1. DL manuals
  2. JBL
  3. Speakers
  4. FLIP3
  5. Service Manual

JBL FLIP3 Service Manual

Other manuals for FLIP3: Quick Start Manual
Manual is about: Bluetooth Portable Speaker, Black/Grey/Orange/Yellow/Blue/Red/Teal/Pink

Summary of FLIP3

  • Page 1

    Released global quality 2015 harman consumer group, inc. Rev 1.3 8500 balboa boulevard northridge, california 91329 contents 2 3 6 7 technical specifications safety instruction, wa rning & notes reset instruction set block diagram set wiring diagram disassembly instruction schematic diagrams pcb lay...

  • Page 2: Technical Specifications

    Technical specifications 1 audio section 1.1.1 speaker output description specification rated output power 2 x 8w +-10% (measure before power limiter at 1% thd). Please refer to acoustic design specification. Input sensitivity aux : 370mv +/- 10% wireless input:-9dbfs +/-1db input overload aux : 1v ...

  • Page 3

    1.1.2 microphone short circuit protection at output stage the amplifier should be protected so that no functional failure occurs when it is operated with a short across its output stage for 2 minutes. The amplifier should recover after removing the short condition. Dc offset protection the amplifier...

  • Page 4

    1.3 bluetooth section 1.3.1 general description specification bluetooth standard version 4.1 frequency band 2.402 – 2.480 ghz host interface uart profile supported hfp (audio gateway and handsfree) a2dp (advanced audio distribution profile) avrcp (audio/video remote control profile) refer srd audio ...

  • Page 5

    1.3.4 transmitter performance @edr mode description specification relative transmit power @ antenna connector -2 to 1 dbm edr carrier frequency stability and modulation accuracy _ǵ 0 _.+] _ǵ l _.+] _ǵ 0 + ǵ l _.+] 506'(90 '(90 3hdn'(90 edr differential phase encoding >=99% 1.3.5 antenna performance ...

  • Page 6

    1.5 battery section 1.5.1 general specification description specification standard and method of measurement typical capacity 3000 mah charge voltage 4.2v output voltage typical : 3.7v limit : 4.2v no load condition cut off voltage typical : 3.0v limit : 2.8v standard charging method 0.5c constant c...

  • Page 7

    1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with a dry cloth. 7. Do not block any ventilation openings.Install in accordance with the manufacturer’s instructions. 8. Do not install ne...

  • Page 8

    Each precaution in this manual should be followed during servicing. Components identified with the iec symbol in the parts list are special significance to safety. When replacing a component identified with , use only the replacement parts designated, or parts with the same ratings or resistance, wa...

  • Page 9

    Safety precautions the following check should be performed for the continued protection of the customer and service technician. Leakage current check measure leakage current to a known earth ground (water pipe, conduit, etc.) by connecting a leakage current tester between the earth ground and all ex...

  • Page 10

    Hw reset: hold down the buttons “bluetooth & vol+ & vol-” for 2 seconds key in power on mode. Factory reset: hold down the buttons “phone & vol+” for 5 seconds in power on mode. 4.

  • Page 11

    • bc8670 power led jbl link led bt led 10v bt antenna 5v 4ohm x2 usb upgrade d+/d- i2c charge status ba ery detect aux_in ti class d tpa3130 bt module(bm870) csr8670 (bt and mcu) power key and other keys v+/v- key ba ery leds micro usb 1.8a/0.5a/ 1a ba ery charger mp2637 input voltage detect mic1 on...

  • Page 12

    Set wiring diagram 6.

  • Page 13

    Toolslist 序号 名称 备注 序号 (number) 名称 （name） 备注 (remark) 小号电批头 1 小号电批头 screw driver （small） 2.0 （small） 2 中号电批头 screw 3 0 2 driver （middle） 3.0 一字螺丝刀（包美纹胶纸）’ 3 翘刀knife 一字螺丝刀（包美纹胶纸） - ’typeknife(wrappedbytape) 电批 4 electrical screw driver 1 2 3 4 7 - 1.

  • Page 14

    1.先用翘刀沿着网罩与双色件间隙（按键面对 面）从上往下稍微翘起open the grille 2.再用翘刀沿着网罩与双 面）从上往下稍微翘起o 面）从上往下稍微翘起openthegrille carefullyusingscrewdriverbasedonthe direction. 面）从上往下稍微翘起o (closetobuttons)caref driverbasedonthed z型电批 4 用z型电批将产品双色件两头的4颗螺丝取下 2 1 4 3 4.用z型电批将产品双色件两头的4颗螺丝取下 （批头用2.0）takeoffthescrew...

  • Page 15

    1 3 4 6 2 5 6 6.将灯板软胶垫撕扯取掉（底部备3m胶纸） 左辐射器 takeofftherubberpart 7.用电批将左右辐射器如 下（批头用2 0）take o 下（批头用2.0）takeo twoendsasshowed 2 3 1 4 9 将led灯板及按键板的13pin及6pin排线 1 4 9.将led灯板及按键板的13pin及6pin排线 （fpc），拔拆方法为将贴片fpc插座扣位90° 翻起后再将排线取出，再将pcb板取下（底部 备3m胶）take off the 13pin cable and 6pin 10 用电批将左右喇叭共计 备3m胶...

  • Page 16

    12.先将腔体右侧3p及13p排线（fpc）及麦克 风2p aux板3p排插线从主板上取下 再用 13.将pcb板从腔体左边向 往另 方向推）推出后将 风2p、aux板3p排插线从主板上取下，再用 翘刀将pcb板两边固定黄胶翘开清理干净take offthe3pin,13pincable,2pinmiccable d 3 i i bl d th l th 往另一方向推）推出后将 线取下pushthepcba showedandthentake and3pinmiccable,andthencleanthe glueasshowediny...

  • Page 17

    1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 d d c c b b a a title number revision size a2 date: 2015/3/17 sheet of file: d:\e\..\amp(20150227).Schdoc drawn by: modsel 1 sdz 2 faultz 3 rinp 4 rinn 5 plimit 6 gvdd 7 gain/slv 8 gnd 9 linp 10 linn 11 mute 12 am2 13 am1 14 am0 15 sync 16 avcc 17 pvcc 18 pvcc 19 bsnl...

  • Page 18

    Harman consumer group harman international shenzhen, guangdong, china size title rev. Sheet of scale: b drawing no. Created checked a b c d a b c 1 2 3 4 1 2 3 4 d date cad file: revision history rev eco checked date proprietary information - these documents and the information contained therein are...

  • Page 19

    1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 d d c c b b a a title number revision size a2 date: 2015/3/17 sheet of file: d:\e\..\io_expander(20150227).Schdoc drawn by: p12 15 p11 14 p10 13 gnd 12 p07 11 p06 10 p05 9 p04 8 p03 7 p02 6 p01 5 p00 4 /reset 3 a1 2 /int 1 p13 16 p14 17 p15 18 p16 19 p17 20 a0 21 scl ...

  • Page 20

    1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 d d c c b b a a title number revision size a2 date: 2015/3/17 sheet of file: d:\e\..\key+led board(20150227).Schdoc drawn by: jbl_link_key agnd power white power bt blue led agnd battery >75% white agnd agnd agnd agnd agnd agnd battery 60-75% white battery 45-60% whit...

  • Page 21

    1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 d d c c b b a a title number revision size a2 date: 2015/3/17 sheet of file: d:\e\..\key1 board(20150114).Schdoc drawn by: agnd bt_key v- v+ phone agnd bt_rsset_in_1 agnd 10v c154 1uf 100k r167 100k r168 100k r169 nc r191 nc r192 nc r195 nc r196 1 2 3 4 5 6 j100 0.5s-...

  • Page 22

    1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 d d c c b b a a title number revision size a2 date: 2015/3/17 sheet of file: d:\e\..\power(20150105).Schdoc drawn by: n/ c 1 ch g 2 b oos t 3 csp 4 ba t t 5 agnd 6 olim 7 iset 8 ntc 9 fb 10 acok 11 reg 12 tm r 13 pw in 14 il im 15 vc c 16 vb 17 en 18 mode 19 vin 20 sy...

  • Page 23

    1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 d d c c b b a a title number revision size a2 date: 2015/3/17 sheet of file: d:\e\..\usb_socket(20150227).Schdoc drawn by: agnd 4 2 3 j301 pj-321b 1 2 3 4 j12 b 4b-ph-k-s c800 nc c801 esd0402v18c15 c802 esd0402v18c15 vbus 1 d- 2 d+ 3 id 4 gnd 5 sh ie d 0 con600 micro_...

  • Page 24

    Layout diagram - main board 9.

  • Page 25

    Layout diagram - usb board.

  • Page 26

    Layout diagram - led board.

  • Page 27

    Layout diagram - key board.

  • Page 28

    Mechanical exploded view 10

  • Page 29

    Spare parts list pos. No. Part number description 2 25104880202009 usb cover flip3 black nd 2 25104880202029 usb cover flip3 pink nd 2 25104880202019 usb cover flip3 grey nd 2 25104880202039 usb cover flip3 teal nd 2 25104880202049 usb cover flip3 blue nd 2 25104880202059 usb cover flip3 red nd 2 25...

  • Page 30

    Revision list version 1.0 initial release for jbl flip3. Update on page 11 for grille ass’y part numbers. Version 1.1 add position number for part list on page 11 version 1. 2 grille ass'y p/n on page 29 updated. Version 1. 3.