- DL manuals
- JBL
- Speakers
- LSR6300 Series
- Owner's Manual
JBL LSR6300 Series Owner's Manual
Summary of LSR6300 Series
Page 1
Lsr6300 studio monitors owner’s manual.
Page 2
Important safety instructions 2 caution risk of electric shock do not open! Do not expose to rain or moisture! Attention risque de choc Électrique ne pas enlever! Ne pas exposer Á la pluie ni Á l'humiditÉ! Explanation of graphic symbols the exclamation point within an equilateral triangle is intende...
Page 3
Table of contents 3 introduction 4 getting started 5 unpacking 5 placement 5 power connections 6 making sound 6 lsr6328p biamplified studio monitor system 7 - 9 audio connections 7 ac power connections 8 audio level adjustment 8 low frequency adjustment 8 high frequency adjustment 9 led indication 9...
Page 4
Introduction 4 congratulation on your purchase of lsr6300 studio monitors. All lsr6300 models incorporate proprietary and patented jbl transducer and network technologies., to provide ultra-accurate response, and exceptional spl capability. Because production rooms are acousti- cally less-than-perfe...
Page 5
5 getting started unpacking: when removing the systems from their packaging, it is important not to grasp the units from the front. Because the high frequency device is located near the top of the cabinet on the front baffle, a stray hand or finger can cause damage. The best way to safely unpack you...
Page 6
Getting started 6 the lsr6312sp can be placed in either a vertical or horizontal orientation. More important than orientation is the physical position in the room. Angling toward the listening position: the lsr6300-series monitors should be angled to directly face the listener. The center of the hig...
Page 7
7 lsr6328p biamplified studio monitor system the lsr6328p bi-amplified studio monitor sets the standard for exceptional performance in near field design. With a combination of advanced transducer engineering and powerful drive electronics, the lsr6328p meets the professional’s requirement for accura...
Page 8
Ac power connections the lsr6328p can accommodate power from 100 to 250 vac 50/60 hz by way of an autosensing power supply. This requires no atten- tion on the part of the user. The ground terminal of the iec plug is required by wiring codes and regulations. It must always be connected to the electr...
Page 9
Lsr6328p biamplified studio monitor system 9 boundary compensation switch 5 introduces a low frequency shelf roll-off of -1.5 db, while switch 6 introduces a low frequency shelf rolloff of -3 db. Engaging both switches will produce a low frequency shelf rolloff of -4.5 db. These functions are known ...
Page 10
10 lsr6332 studio monitor system the lsr6332 linear spatial reference studio monitor combines jbl's latest in transducer and technology with recent breakthroughs in system design to provide a more accurate studio reference in a variety of pro- duction environments. The neodymium 12" woofer is based ...
Page 11
11 lsr6332 studio monitor system this adjustment is accomplished via the barrier strip on the back of the enclosure located above the dual pair of 5-way binding posts. Moving the link between the 0 and -1 db positions will change the high frequency drive level. Please note that the loudspeaker shoul...
Page 12: Lsr6312Sp
Lsr6312sp powered subwoofer system 12 the lsr6312sp active subwoofer consists of a neodymium differential drive ndd™ 12" neodymium woofer integrated with a powerful 260 watt continuous power output amplifier. The active drive circuitry has been developed to maximize the acoustic output power while m...
Page 13
There are several ways to connect the lsr6312sp in a monitoring system including stereo, multi-channel for- mats such as dolby prologic, ac-3, dts, and others. The bass management system in the lsr6312sp pro- vides the flexibility to switch between configurations. In a stereo configuration, it is ty...
Page 14
Input trim active +4 dbu input sensitivity +8 dbu input sensitivity signal polarity inverted -4 db bass alignment rmc defeat ac power connections the lsr6312sp power supply voltage is internally set at the factory for 100-125v or 200-250v. The ground terminal of the iec plug is required by wiring co...
Page 15
15 lsr6312sp powered studio subwoofer system l in c in r in direct lfe in source l out r out c out out out out out center right left right rear left rear out out in in in in in system configuration.
Page 16
16 appendix a wiring requirements for optimum performance, some attention to wiring details now can reduce system degradation later. The cabling recommendations given below follow standard wiring practice for differential inputs. Balanced sources: the best way to run your system is balanced, where b...
Page 17
17 appendex a diagram d details the connections using single conductor shielded cable with a tip/ring/sleeve plug for the 6328p input. Single con- ductor cable should be used as a last resort as it provides the greatest likelihood of problems. The "hot" (+) signal should be connect- ed to the tip of...
Page 18
Appendix b mounting specifications for lsr6328p, lsr6332 and lsr6312sp mounting points are provided for use with readily available industry standard mounting brackets. Mounting points are located on the bottom of the lsr6328p and rears of the lsr6332 and lsr6312sp models. Fasterner specifications: t...
Page 19
Specifications - lsr6328p 19 frequency response (+1, -1.5 db): 50 hz - 20 khz enclosure resonance frequency: 38 hz low frequency extension: user controls set to default -3 db: 46 hz -10 db: 36 hz low-high frequency crossover: 1.7 khz 6th-order acoustic linkwitz-riley distortion, 96 db spl, 1 m: mid-...
Page 20
Specifications - lsr6332 20 notes: all measurements unless otherwise stated made anechoically at 2 meters and refer- enced to 1 meter by the inverse square law. The reference measurement microphone position is located perpendicular to the center line of the mid and high frequency transducers, at the...
Page 21
21 specifications - lsr6312sp notes: 1 left, center and right input 2 produces quasi-fourth order linkwitz-riley acoustic high pass alignment when used with lsr6328p or lsr6332. All measurements unless otherwise stated made anechoically in a 4p environment at 2 meters and referenced to 1 meter by th...
Page 22
22.
Page 23
Who is protected by this warranty? Your jbl warranty protects the original owner and all subsequent owners so long as: a.) your jbl product has been purchased in the continental united states, hawaii or alaska. (this warranty does not apply to jbl products purchased elsewhere except for purchases th...
Page 24
Mailing address: jbl professional 8500 balboa blvd. Northridge, ca 91329 shipping address: jbl professional 8370 balboa blvd., dock d northridge, ca 91329 customer service monday through friday 8:00am - 5:00pm pacific coast time in the u.S.A. (800) 8jblpro (800.852.5776) www.Jblproservice.Com on the...