JBL PowerBass PB10 Owner's Manual

Other manuals for PowerBass PB10: Service Manual, Service Manual, Preliminary Service Manual

Manual is about: PowerBass Series Powered Subwoofer

Page of 8

Download

Print this page

Bookmark us

S P E C I F I C A T I O N S

Occasional refinements may be made to existing products without notice,

but will always meet or exceed original specifications unless otherwise

stated.

* Trademarks of Dolby Laboratories.

DTS is a registered trademark of Digital Theater Systems, Inc.

PB10

PB12

Amplifier

Power (RMS):

150 Watts

250 Watts

Driver:

10" Pure-Cellulose Fiber

12" Pure-Cellulose Fiber

Inputs:

Line Level (switchable to LFE)

and Speaker Level with

gold-plated 5-way binding posts

Outputs:

Speaker Level, High-Pass with

gold-plated 5-way binding posts

Low-Pass

Frequency:

Continuously variable

from 50Hz – 150Hz

High-Pass

Frequency:

150Hz when using

speaker-level output

speaker-level outputs

Frequency

Response:

27Hz – low-pass

25Hz – low-pass

crossover setting

Dimensions

(H x W x D):

14" (16" with feet) x 14" x 15"

15-1/2" (17-1/2" with feet) x 15" x 16"

356mm (406mm with feet) x

394mm (445mm with feet) x

356mm x 381mm

381mm x 406mm

Weight:

35 lb/15.9kg

40 lb/18.2kg

JBL Consumer Products

250 Crossways Park Drive, Woodbury, NY 11797

8500 Balboa Boulevard, Northridge, CA 91329

800-336-4JBL (4525) (USA only)

www.jbl.com

of JBL, Incorporated.

Part No. 338129-001

D E S I G N G O A L :

Bring the thrill of live performance and movie sound to

the home environment by calling on JBL’s professional engineering leadership.

W O O F E R T Y P E :

Pure cellulose fiber

P O R T D E S I G N :

FreeFlow™ flared

P R O F E S S I O N A L R E F E R E N C E :

Cinema Loudspeaker Series

O W N E R ’ S G U I D E

P R O S O U N D

C O M E S H O M E

™

P R O D U C T L I N E :

PowerBass

™

Series

M O D E L

PB10, PB12

N U M B E R :

1 2 3 4 5 6 7 Next › »

Summary of PowerBass PB10

Page 1
S p e c i f i c a t i o n s occasional refinements may be made to existing products without notice, but will always meet or exceed original specifications unless otherwise stated. * trademarks of dolby laboratories. Dts is a registered trademark of digital theater systems, inc. Pb10 pb12 amplifier p...
Page 2: X +
X + 0 + y 2 0 m h z x + 0 + y 2 0 m h z ” x + 0 + y 2 t h a n k y o u f o r c h o o s i n g j b l for more than 50 years, jbl has been involved in every aspect of music and film recording and reproduction, from live performances to the recordings you play in your home, car or office. We’re confident...
Page 3: Caution
2 1. Read instructions. All the safety and operating instructions should be read before the product is operated. 2. Retain instructions. The safety and operating instructions should be retained for future reference. 3. Heed warnings. All warnings on the product and in the operating instructions shou...
Page 4
3 s p e a k e r p l a c e m e n t • as a general rule, bass response increases as a subwoofer is placed closer to a wall. Therefore, bass output is maximized when the subwoofer is placed in a corner. • it is also recommended that the subwoofer be positioned along the same wall as the front loudspeak...
Page 5: + –
Dolby pro logic (non-digital) – line level use this installation method for dolby pro logic appli- cations (not dolby digital, dts or other digital processing), where the receiver/processor is equipped with a subwoofer output or a volume-controlled preamp (line-) level output: use rca-type patch cor...
Page 6: + –
5 dolby digital or dts (or other digital surround mode) connection use this installation method for dolby digital, dts or other digital surround processors: important: make sure that the lfe toggle switch on the subwoofer is in the “lfe” position. Use the line-level input jacks for the low- frequenc...
Page 7: O P E R A T I O N
6 o p e r a t i o n when the unit is plugged in and the power switch is on and no signal is received, the leds on the front of the unit will turn red. When a signal is present, the leds will turn green. Note: it will take several minutes for the leds to turn from green to red after the input signal ...
Page 8
7 t r o u b l e s h o o t i n g if you used the high-level (speaker) inputs and there is no sound from any of the speakers: • check that receiver/amplifier is on and a source is playing. • check that powered subwoofer is plugged into an active electrical outlet and is switched on. • check all wires ...