JBL S120P II STUDIO SERIES Owner's Manual

Page of 8

Download

Print this page

Bookmark us

S P E C I F I C A T I O N S

All features and specifications are subject to change without notice.

* Trademarks of Dolby Laboratories.

DTS is a registered trademark of Digital Theater Systems, Inc.

Amplifier Power (RMS):

400 Watts

Driver:

12" PolyPlas

™

(polymer-coated cellulose fiber) cone;

rubber surround; SFG

™

; magnetic shorting rings;

high-temp, oversized, fiberglass voice coil; HeatScape

™

motor structure; cast-aluminum basket

Inputs:

Line Level (switchable to LFE), BassQ

™

and

Speaker Level with gold-plated, 5-way binding posts

Outputs:

BassQ and Speaker Level (High-Pass with

gold-plated, 5-way binding posts)

Low-Pass Frequency:

Continuously variable from 50Hz – 150Hz

High-Pass Frequency:

150Hz when using speaker-level outputs

Frequency Response:

22Hz – Low-pass crossover setting

Dimensions (H x W x D):

17-3/16" (with feet, without spikes) x 16-3/16" x 18" (19" with grille)

437mm (with feet, without spikes) x 411mm x 457mm (483mm with grille)

Weight:

56 lb/25.5kg

JBL Consumer Products

250 Crossways Park Drive, Woodbury, NY 11797

8500 Balboa Boulevard, Northridge, CA 91329

800-336-4JBL (4525) (USA only)

www.jbl.com

JBL is a registered trademark of JBL, Incorporated.

Part No.: 338003-001

D E S I G N G O A L : Bring the thrill of live performance and movie sound to

the home environment by calling on JBL’s professional engineering leadership.

W O O F E R T Y P E : Pure-cellulose fiber

P O R T D E S I G N : FreeFlow™ flared

P R O F E S S I O N A L R E F E R E N C E : Studio Monitor

O W N E R ’ S G U I D E

P R O S O U N D

C O M E S H O M E

™

P R O D U C T L I N E :

STUDIO

™

SERIES

M O D E L

S120P

N U M B E R :

1 2 3 4 5 6 7 Next › »

Summary of S120P II STUDIO SERIES

Page 1
S p e c i f i c a t i o n s all features and specifications are subject to change without notice. * trademarks of dolby laboratories. Dts is a registered trademark of digital theater systems, inc. Amplifier power (rms): 400 watts driver: 12" polyplas ™ (polymer-coated cellulose fiber) cone; rubber s...
Page 2: X +
X + 0 + y 2 0 m h z x + 0 + y 2 0 m h z ” x + 0 + y 2 t h a n k y o u f o r c h o o s i n g j b l for more than 50 years, jbl has been involved in every aspect of music and film recording and reproduction, from live performances to the recordings you play in your home, car or office. We’re confident...
Page 3: Caution
2 1. Read instructions. All the safety and operating instructions should be read before the product is operated. 2. Retain instructions. The safety and operating instructions should be retained for future reference. 3. Heed warnings. All warnings on the product and in the operating instructions shou...
Page 4
3 s p e a k e r p l a c e m e n t • as a general rule, bass response increases as a subwoofer is placed closer to a wall. Therefore, bass output is maximized when the subwoofer is placed in a corner. • it is also recommended that the subwoofer be positioned along the same wall as the front loudspeak...
Page 5
Dolby pro logic (non-digital) – line level use this installation method for dolby pro logic appli- cations (not dolby digital, dts or other digital processing), where the receiver/processor is equipped with a subwoofer output or a volume-controlled preamp (line-) level output: use rca-type patch cor...
Page 6
5 dolby digital or dts (or other digital surround mode) connection use this installation method for dolby digital, dts or other digital surround processors: important: make sure that the lfe toggle switch ™ on the subwoofer is in the “lfe” position. Use the line level input jacks ¶ for the low- freq...
Page 7: O P E R A T I O N
6 o p e r a t i o n the s120p ii is equipped with both a master power switch ‚ and an auto turn-on/turn- off switch £. In order to function, the s120p ii must be plugged into an active electrical outlet (but not an accessories outlet on another component of your audio system such as a receiver), and...
Page 8
7 t r o u b l e s h o o t i n g if you used the high level (speaker) inputs • and there is no sound from any of the speakers: • check that receiver/amplifier is on and a source is playing. • check that powered subwoofer is plugged into an active electrical outlet and is switched on £‚. • check all w...