Summary of Lil' Buttie
Page 1
Lil' buttief telephone test set user's guide www.Jdsu.Com/hbn.
Page 2
Norm rev flash store mem last/p line p olarity tone pulse lil' buttie made in usa tm test-um inc. Www com .Test-u m. Talk bell mon mute 1 2 3 abc def 0 * # / t qz 4 5 6 ghi jkl mno 7 8 9 prs tuv wxy flsh store lst/p mem headset jack mute button rj jack talk - bell - monitor switch line polarity indi...
Page 3: Caution
Caution please follow correct safety practices when operating this unit. Do not connect this unit to 110 volt or 220 volt ac electric power lines. Correct operation is entirely the responsibility of the user. Should the lil' buttie, intentionally or by accident, be connected to electric power, all w...
Page 4
Pocket and can be worn on either ear. Its unobtrusive design makes it easy to use while wearing a hard hat or inclement weather clothing. The body is made of high impact resistant abs to withstand the rough handling and shocks that craft tools are normally subjected to in their everyday use. A belt ...
Page 5: Features
Features tone and pulse dialing microphone mute feature last number redial - digits continuous line polarity indication ( talk or monitor ) electronic ringer amplified line monitor for volume levels comparable to “off hook” operation. Modular cord set attachment low battery indicator headset jack fo...
Page 6: And Leds
Function switches, buttons, and leds talk-bell-monitor switch - this three- position slide switch is located on the side of the unit below the receiver. It is used to select the mode of operation. Talk - this position creates an off-hook condition. In this mode, the unit can be used for signaling, c...
Page 7
Mute - this button is located on the opposite side of the talk-bell-monitor switch. Press and hold to shut the unit's transmitter off. This feature may also be used to improve communications in noisy locations where it is difficult for the user to hear a person on the other end of the line. Flash - ...
Page 8: Line Polarity Indicators
6 mem - to retrieve a stored number, press mem and the numeric key (0-9) you stored the number to and the number will be automatically dialed. Line polarity indicators norm - a green led indicates correct polarity rev - a red led indicates reversed line polarity battery low (batt low) - when operate...
Page 9: Operation
7 operation note: always position the talk-bell- monitor switch in the monitor position before connecting to a subscriber line to avoid possibly compromising any transmission in progress. Connecting to a line monitor select the monitor mode. Connect the red cord set lead to ring (- ) and black cord ...
Page 10: Mixed-Mode Dialing
Select the talk mode and confirm that dial tone is present. Proceed with dialing, line testing, etc. Mixed-mode dialing in certain situations, it may be necessary to set up a call using both pulse and tone dialing. In this situation, a number can be entered in the pulse mode then by pressing the */t...
Page 11: Polarity Check
9 to answer the call, switch the unit to talk . To disable the ringer, switch the unit to monitor mode. Polarity check the lil' buttie indicates polarity continuously in monitor and talk modes as long as the line is powered. To test, select the monitor or talk mode. Connect the black cord set lead t...
Page 12: Line Cord Connections
0 line cord connections the lil' buttie is designed with a standard 6-position modular jack for quick connection to various cord sets. The jack is located at the base of the unit below the microphone. To replace the cord set, simply remove the strain relief attachment screw and unplug the cord set. ...
Page 13: Accessories
Accessories lil' buttie test sets are sold with either a piercing clip set, a mini headset, and a metal belt clip (lb00), a bed of nails cord set, a mini headset, and a metal belt clip (lb0) or the bed of nails cord set, mini headset, and at&t hook/clip assembly (lb). Replacement cord sets bed of na...
Page 14: Belt Clip Attachment
Belt clip attachment to install the belt clip attachment, remove the strain relief attahment screw and position the belt clip as shown. Attach the clip using the provided /" flat head screw. Take care not to over torque the screw to cause damage to the body. Optional accessories for a complete descr...
Page 15: Battery Installation
Battery installation battery not included. Should the batt low led indicate low battery, the battery should be replaced as shown below. Using a # phillips screwdriver, unscrew and remove the battery cover on the back of the lil' buttie. Connect a 9v alkaline battery to the battery snaps. Slide the b...
Page 16: Specifications
Specifications electrical return loss — @ 600 ohms: greater than db line current range: to ma apparent line resistance: 7 ohms at 0ma rotary dial output pulse rate: 0 pps +/- 0% m/b ratio: 60/0% +/- % interdigit interval: 0 msec leakage during break: >0 kohms dtmf output (into 600 ohms ) tone freque...
Page 17: Physical
Physical length without lanyard: 7. In (. Cm) width: .0 in (6. Cm ) height: .6 in (. Cm ) weight with cord set: ozs. (7 gms) environmental temperature — operating: -0°c to 60°c storage: -0°c to 66°c specifications subject to change.
Page 18: Maintenance
6 maintenance the test set may be cleaned with a damp cloth. If heavy accumulations of dirt are present, a small amount of liquid soap may be applied to the cloth to assist in cleaning. Do not use solvents, scouring powders, or other abrasive cleaners as they may scratch the unit and/or cause malfun...
Page 19: Warranty
7 warranty jdsu guarantees that its products will be free of all defects in material and workmanship. This warranty extends for the period of months for test instruments and months for cables from date of manufacture or purchase (proof of purchase required). All product deemed defective under this w...
Page 20
In an environmentally friendly manner, and in compliance with all applicable national and international waste legislation. It is the responsibility of the equipment owner to return the equipment to jdsu for appropriate disposal. If the equipment was imported by a reseller whose name or logo is marke...
Page 21: Shipping
9 shipping before returning any product to jdsu, you must first request a return merchandise authorization number by contacting our customer service dept. At (0) -00. No shipments will be accepted without this number, which must be clearly marked on the shipping label. Ship the equipment with a copy...
Page 22: Contact Information:
Contact information: 808 calle plano camarillo, ca 93012 usa regional sales north america tel: +1 805 383 1500 fax:+1 805 383 1595 latin america tel: +55 11 5503 3800 fax:+55 11 5505 1598 asia pacific tel: +852 2892 0990 fax:+852 2892 0770 emea tel: +49 7121 86 2222 fax:+49 7121 86 1222 customer ser...