1. DL manuals
  2. Jeanneau
  3. Boat
  4. MERRY FISHER 855 OFF SHORE
  5. Owner's Manual

Jeanneau MERRY FISHER 855 OFF SHORE Owner's Manual

Summary of MERRY FISHER 855 OFF SHORE

  • Page 1

    Merry fisher 855 off shore owner's manual 993650 index b.

  • Page 3: Welcome Aboard

    -1/104 welcome aboard madam, sir, you have just taken delivery of your new jeanneau boat and we thank you for the confidence you have shown us in ordering a vessel of our brand. The whole jeanneau team welcomes you aboard. A jeanneau is made to last, in order to bring you all the pleasure you expect...

  • Page 5: Introduction

    1/104 introduction the users of the boat are informed of the following: this user guide/owner's manual is not a maintenance or repair guide. In case of difficulty do not hesitate to call on the services of your concessionaire jeanneau. Any alterations which may affect the safety specifications of th...

  • Page 6

    2/104 anyone on the deck shall wear a life jacket or a buoyancy aid. The safety regulations as defined by the sailing code and enforced by the ’’colreg’’ should be observed. Name plate: some of the data is shown on the manufacturer's plate fixed to the boat. The explanation of the data is given in t...

  • Page 7: History Of Updates

    3/104 history of updates •index a .................................................................................................................. 12/2014 •index b .................................................................................................................. 01/2015.

  • Page 9: Contents

    5/104 contents introduction chapter 1 ...... Specifications and warranty ............................................Page 7 chapter 2 ...... Safety ........................................................................................Page 13 chapter 3 ...... Hull .....................................

  • Page 11

    7/104 specifications and warranty technical specifications certification design category your boat 1.

  • Page 12

    8/104 technical specifications - merry fisher 855 off shore l.O.A (with platform)................................................................................................. 8,72 m l.O.A (without platform .............................................................................................

  • Page 13

    9/104 design category design category wind force (beaufort scale) significant height of waves to be considered (in metres h 1/3) vessel designed for navigation: a - "at high sea" b - "in open sea" c - "near to the coast" d - "in sheltered waters" over 8 up to and including 8 up to and including 6 up...

  • Page 14

    10/104 category a: at high sea the boat is designed to sail in winds that may exceed beaufort force 8 and in waves of a significant height of 4 metres and more. This craft is largely self-sufficient. Abnormal conditions such as hurricanes are excluded. Such conditions may be encountered on extended ...

  • Page 15

    11/104 your boat version name of the boat ............................................................. Name of the owner ............................................................. Address ............................................................. .................................................

  • Page 17: Safety

    13/104 safety safety equipment general information gas system recommendations for gas fight against fire bilge pump system instructions in the event of steering gear failure 2.

  • Page 18

    14/104 safety equipment swimming ladder (means of coming back onboard) reference 1 position of the liferaft (not supplied) reference 2 swimming ladder reference 1 liferaft reference 2.

  • Page 19

    15/104 general information dangers the major hazards concern: - the gas system. - the electrical system. - the handling of the vessel. - the motorisation. Please refer to the relevant paragraphs. Danger - fuel leaks or vapour represent a danger of fire and explosion. - ventilate the compartment leng...

  • Page 20

    16/104 gas system locker closed locker open (the valve is located in the trunk gas cylinder) warning - for all recommendations concerning gas: refer to chapter 2, «safety». - don't use a solution containing ammonia. - don't use a flame to detect leaks. - don't smoke, don't use a naked flame when you...

  • Page 21

    17/104 gas system diagram ref designation 1 hot plate 2 valve hot plate 3 gas cylinder locker 4 gas system 5 regulator valve 6 gas cylinder 2 s a f e t y.

  • Page 22

    18/104 location - gas ref designation 1 cooker 2 drain - gas cylinder locker 3 supply valve - gas 4 regulator valve 5 gas cylinder locker 1 3 4 5 2.

  • Page 23

    19/104 recommendations for gas type of cylinder: butane, service pressure 10 kg/cm 2 or according to current standards of your country). Close the valves on the system and on the cylinder when the appliances are not used. Close the valves before you change cylinders and immediately in case of emerge...

  • Page 24

    20/104 regularly check and replace the rubber tubings that link the cylinder to one end of the circuit and the stove to the other one, depending on the norms and regulations in force in your country. Pay particular attention to keep in good condition the screw thread of the cylinder on which the reg...

  • Page 25

    21/104 fight against fire it is the owner's or the skipper's responsibility: - to have the extinguishers checked in pursuance of the instructions given. - use extinguisher replacements with equivalent features (same capacity and fire resistance) if the ones in place are out of date or have been used...

  • Page 26

    22/104 extinguishers the extinguishers are part of the compulsory equipment. An extinguisher or a fire blanket shall be set less than 2 m from any flame appliance. Extinguishers must be placed less than 5 m from any berth. An extinguisher shall be less than 1 m from the steering station. The extingu...

  • Page 27

    23/104 supply valve - fuel location - on the fuel tank 2 s a f e t y.

  • Page 28

    24/104 manual bilge pump location arm - pump location operation capacity: 0.7 l / blow warning - the bilge pump system is not designed to provide buoyancy to the boat in case of damage. - the bilge pump system is designed to drive out the water being either sea spray or leaks but absolutely not the ...

  • Page 29

    25/104 schema - bilge pump system 2 1 2 3 4 5 6 7 8 9 10 11 12 13 14 s a f e t y.

  • Page 30

    26/104 ref designation 1 drain scupper - gangway 2 manual bilge pump 3 drain scupper - chain locker 4 electric bilge pump 5 washbasin drain plug 6 washbasin draining 7 forward electrical bilge pump draining 8 sink plug hole 9 sink draining 10 draining of manual bilge pump 11 electric bilge pump drai...

  • Page 31

    27/104 bilge pump system procedure to be followed - switch on the electric bilge pump. - if necessary activate the manual pump. - identify the source of the leak by tasting the water and decide on the relevant action to be taken: • freshwater = watertank leak. • seawater = breach of hull. Electric b...

  • Page 32

    28/104 manual bilge pump location: in the cockpit. The control arm of the pump shall be kept accessible whatever the circumstances. Instructions in the event of steering gear failure - stop the engine. - drop anchor to avoid drifting. - find out if you can solve the problem yourself by looking at th...

  • Page 33: Hull

    29/104 hull maintenance of the hull lifting 3.

  • Page 34

    30/104 lifting wetted area: 20 m² upper limit of antifoul: measurements are expressed in mm. Precaution - consult the harbourmaster's office to find out the conditions of water use and the maintenance area for cleaning your vessel. - it is necessary to seek the advice of your concessionnaire with re...

  • Page 35

    31/104 maintenance of the hull the materials and equipments of your boat have been selected because of their high quality and performance and ease of maintenance. However you shall carry out a minimum maintenance in order to protect your boat from outside attacks (salt, sun, electrolysis ...). Prefe...

  • Page 37: Deck

    33/104 deck navigation - deck layout mooring lines towing stability prevention of man overboard mooring maintenance of the deck 4.

  • Page 38

    34/104 navigation - deck layout p a. Mooring cleats - jack-lines to be fixed to the mooring cleats b. Towing: - at the bow, to be towed - at the stern, to tow c. Swimming ladder (means of coming back onboard) d. Ring - handling. Used to maneuver the boat on a trailer warning the sudden closing of a ...

  • Page 39: Deck

    35/104 mooring lines a sufficient number of mooring lines suitably sized and suitable for the environment shall be on board for mooring your boat. - always manoeuvre your boat using the engine. - make allowance for the current and wind when you handle your boat. - protect your boat to the highest de...

  • Page 40

    36/104 opening / closure sliding hatch window lock - to be kept closed when sailing access - cockpit danger: it is essential that the door remains closed while sailing rod holder.

  • Page 41: Deck

    37/104 cockpit fixed box location mechanism samson post the only function of the samson post is to support the navigation light. Any other use is dangerous and forbidden. 4 deck.

  • Page 42

    38/104 stability breaking waves represent a serious danger for stability and for taking in water. Close the companionway doors and hatches in heavy seas. During sailing keep all the portholes, windows and doors closed. - the stability is reduced when you add weight in the upper parts. - stability ma...

  • Page 43: Deck

    39/104 deck electric windlass - breaker location . Operation the windlass operates on the service batteries. Turn on the boat engine. 1. Bow fitting 2. Chain locker 3. Opening - chain locker 4. Chain holder 5. Windlass 12v - 700 w 6. Chain rim - 08 mm diameter 7. Remote control 8. Handle breaker 80a...

  • Page 45: Deck

    41/104 mooring as a rule, set the anchor in at least 3 times the depth of water. Anchoring without windlass - have your boat pointed into the wind and without speed. - pay out the chain while moving back slowly. - once the anchor snags, make it fast by reversing slightly. - secure the hawser or the ...

  • Page 46

    42/104 anchoring by hand with use of a manual windlass - release the windlass brake using the handle located in the chain locker so as to allow the chain lifter to turn freely and to release the anchor from the stem fitting - re-engage the brake and let the anchor hang until the mooring position is ...

  • Page 47: Deck

    43/104 maintenance of the deck preferably wash your boat on shore. Use as few cleaning agents as possible. Don't use solvents or aggressive detergent agents (refer to chapter 3 "hull"). Don't discharge cleaning agents into the water. Regularly brush the deck with a degreasing shampoo and fresh water...

  • Page 49: Steering System

    45/104 steering system steering gear 5.

  • Page 50

    46/104 steering gear steering and turns - the steering only works when the engine is running. It is impossible to make a turn without using the accelerator. - to turn, reduce speed, turn the wheel and then accelerate sufficiently to make the turn. - it stops under the effect of water resistance when...

  • Page 51

    47/104 schema 5 1 2 3 4 5 6 7 8 9 9 (option) 10 s t e e r in g s y s t e m.

  • Page 52

    48/104 ref designation 1 engine control 2 steering wheel 3 control cables 4 steering cable (hydraulic) 5 steering cable (hydraulic) 6 watertight bellows (control cables) 7 watertight bellows (steering cable) 8 piston 9 outboard 10 steering rack.

  • Page 53: Interior

    49/104 interior introduction interior maintenance maintenance of fabrics 6.

  • Page 54

    50/104 introduction deck saloon interior accommodation.

  • Page 55: Interior

    51/104 interior maintenance interior - take advantage of the fine weather to take the settee and berth cushions out. - put the cushions vertically if you leave the boat for long. - use blinds to protect the inside of the boat against uv rays. - carefully remove all crumbs. - make sure the bilges are...

  • Page 56

    52/104 galley warning make sure the temperature of the stove before you close the hood. Mosquito net / blackout curtain pilot seat / leaning post.

  • Page 57: Interior

    53/104 100% polyester/dralon jacquard if you cannot remove the fabric: - clean with the vacuum cleaner. - clean with a foam for synthetic fabrics (please refer to the product instructions). If you can remove the fabric: - hand wash with an ordinary washing powder at 30° c. In both cases, dry cleanin...

  • Page 59: Water And Sewage Water

    55/104 water and sewage water water tanks water system - distribution water system - drainage sewage 7.

  • Page 60

    56/104 water tank operation in order to prevent any handling mistakes, never fill the water and fuel tanks at the same time. During filling, avoid handling contaminants near the fillers. Open and close the filler caps with the suitable key. Check the filler cap seals for condition during filling. Th...

  • Page 61

    57/104 plumbing compartment access: aft cabin water pump 12v + filter 220v water heater 1. Thermostatic mixer valve 2. Water heater - 25 litre cockpit shower spray warning to avoid freezing during very cold spells and/or winter storage bleed the cockpit shower hose water system. Precaution - never o...

  • Page 62

    58/104 operation waste water from the sink, washbasins and heads is drained off by thru-hull fittings with ball valves (the valve is closed when the valve handle is perpendicular to the hose, the valve is open when the valve handle is in line with the hose). All the floors have holes (limber holes) ...

  • Page 63

    59/104 use of washbasin close the valves and turn off the taps after use. Shower shower draining - control draining pump for shower access: hatch - companionway shower draining - intake waste water advice - recommendation - regularly check the valves and thru-hull seacocks for proper operation and w...

  • Page 64

    60/104 sewage use of the marine heads before you use the heads, check that the water intake valve and draining valve are open. To empty the bowl: - set the control lever of the pump slantwise (flush). - operate the pump. To dry the bowl: - set the lever back vertical (dry). - operate the pump. To av...

  • Page 65

    61/104 holding tank capacity: 80 litre respect of the environment - remain informed of local regulations concerning the environment and follow the codes of best practice. - do not drain the contents of the sewage tank near the coast or in zones where it is forbidden. - make use of the port or marina...

  • Page 66

    62/104 sewage - location ref designation 1 marine toilet 2 seawater inlet - wc 3 wc evacuation - to sea 4 wc evacuation - deck 5 vent hole - holding tank 6 holding tank - 85 litre 1 6 2 3 4 5.

  • Page 67

    63/104 use of marine heads equipped with a waste holding tank (wht) open the water intake valve (valve handle parallel to the pipe). In the case of a direct discharge into the sea: open the draining valve. In case you store the waste waters in the tank: make sure the draining valve is closed (valve ...

  • Page 69: Electrical Equipment

    65/104 electrical equipment 12 v dc system electrical circuit, 110-220 v equipment 8.

  • Page 70

    66/104 location 9 9 p p 9 r p 45 47 48 46 39 39 11 4 10 3 39 13 14 37 39 15 16 17 28 38 39 27 42 50 44 12 30 36 29 43 31 32 40 40 42 40 34 26 41 2 1 51 49 35 33 52 b1 b2 ii i.

  • Page 71

    67/104 location ref designation 1 service battery - 110a 2 service battery - 110a 3 engine battery - 70a 4 bow thruster 5 battery switch - starboard engine 6 breaker - 80a (windlass) 7 battery switch of house system 8 battery switch - port engine 9 coupling 10 fuse - bow thruster 8 18 19 20 21 22 23...

  • Page 72

    68/104 ref designation 11 relay box - bow thruster 12 control - bow thruster 13 starboard windscreen wiper 14 port windscreen wiper 15 control panel 16 fuse box 17 control panel (switches) 18 switch - navigation lights & compass light 19 switch - water unit 20 switch - aft electric bilge pump 21 swi...

  • Page 73

    69/104 electrical circuit, 12 vdc general recommendations - never work on a live electric fitting. - the batteries must be strongly fastened. - do not block the battery ventilation ducts, some of them may give off hydrogen which represents a danger of explosion. - the batteries must be handled with ...

  • Page 74

    70/104 access to fuses hatch - head 1. Electronic instruments 2. Fridge 3. Navigation lights 4. Relay box 5. Aft electric bilge pump 6. Shower pump 7. Water unit 8. Cockpit lighting 9. Forward electrical bilge pump 10. Lighting - steering station 11. 12 v socket 12. Wiper 2. Interior lighting 4. Coc...

  • Page 75

    71/104 bow thruster location operation the thruster works with the vessel's engine running. The electric battery switch for the thruster automatically comes on or goes off when the thruster is started or stopped. The dc negative supply is connected to the main earthing point. Nozzle access: forward ...

  • Page 76

    72/104 wiper location wiper tank location: unit - head control fridge control: located - directly on the device during long absence leave the fridge and icebox doors open to avoid mould developing. Defrost the fridge regularly..

  • Page 77

    73/104 location battery switch operation in the case of low engine battery power use the battery coupling function by turning on the coupling handle located in the aft cabin. Once the engines have been restarted make sure that the coupling handle is turned back to its original position. Access 1. Ba...

  • Page 78

    74/104 battery set batteries battery charging is achieved through the alternator coupled to the engine or through use of the 220 v shore charger. Keep the batteries charged enough (essential to ensure them a correct service life). Make the most of time alongside to use the 220 v shore charger so as ...

  • Page 79

    75/104 always check the condition of the batteries and charge system before putting to sea warning - never work on a live electric fitting - do not touch the battery terminals, danger of electric shock. Precaution - switch off the electrical system with the battery switches when the boat is unattend...

  • Page 80

    76/104 electrical circuit, 110-220 v general recommendations certain vessels are equipped (as either standard or optional features depending on the model)with a 110 v or 220 v circuit. The following measures are recommended in order to avoid the danger of electrical shock and fire: - never work on a...

  • Page 81

    77/104 shore power socket 220v shore power socket - 220v - 30a breaker - 220v - 32a access: plumbing compartment from left to right: - 220v - general - water heater - 220v socket 8 e l e c t r ic a l e q u ip m e n t.

  • Page 82

    78/104 equipment general introduction (as far as possible) use electric appliances with double insulation or with three conductors (neutral-live wire-ground). Electronic wire runs are available to complete the boat equipment. Do not install electronic instruments or repeaters less than 1,50 m away f...

  • Page 83

    79/104 electronic - layout of components lead lines loch speedo sounder 8 e l e c t r ic a l e q u ip m e n t.

  • Page 84

    80/104 lead lines keep the log sensor cowl close to the instrument so as to be able to intervene in complete safety. Do not store material on top of the sensors. Auto pilot - to supply power to all elements switch on the "navigation" circuit breaker on the electrical panel. - for use and maintenance...

  • Page 85: Engine

    81/104 engine general information engine fitting 9.

  • Page 86

    82/104 general information type of motorisation precautions of use, operating advice general point - in this vessel, do not install an engine with a greater power and weight than that recommended, this will create a danger for its stability. - fuel which is stored elsewhere than in the fuel-tanks (p...

  • Page 87

    83/104 danger - stop the engine and refrain from smoking during fuel tank filling. - make sure that the ventilation openings in the engine (and generator, if installed) compartment are well cleared. Warning - the tanks' nominal capacity cannot be fully used due to the load and the need to maintain t...

  • Page 88

    84/104 schema - system - fuel ref designation 1 fuel tank 400 litres 2 vent hole 3 deck filler 4 fuel supply valve - port engine 5 fuel filter 6 gauge dial 7 fuel supply valve - starboard engine 8 gauge transmitter 9 fuel filter 1 2 3 4 5 6 7 8 9.

  • Page 89

    85/104 motor these instructions give detailed explanations on proper operation of the engine. - refill before the fuel tanks have almost run dry (the fuel system may be stopped for lack of fuel). - make sure you have enough fuel before sailing. Engine water intake valve the engine water valve is ess...

  • Page 90

    86/104 fuel filter engine running problems may have different origins, including dirty fuel. The injection pump may wear out if there is water in the system. The water results either from the condensation resulting from an insufficiently filled tank, or from a filler cap either not closed properly o...

  • Page 91

    87/104 epa version (united states environmental protection agency) - the maintenance of the complete petrol circuit system must be done professionally every year. It is advisable to clean the circuit only with soapy water. All the fuel circuit connections must be checked once a year. - when cleaning...

  • Page 92

    88/104 wheelhouse - detail synoptic 1. Gauge 2. Compass 3. Tachometer 4. Central - electronic 5. Engine control 6. Engine starter 7. Electrical controls 8. Steering wheel 9. Propeller control 10. Hifi danger attach the cutout to the pilot at engine start..

  • Page 93

    89/104 the instrument panel has all the testing functions of the engine and it does not require any special precaution (refer to engine leaflet). Check the clutch and accelerator cables (lubricate the end fittings and forks). Visibility from the steering station the international regulations to prev...

  • Page 94

    90/104 navigation: reminder of some advice stability during sailing keep all the portholes, windows and doors closed. - the stability is reduced when you add weight in the upper parts. - stability may be reduced when towing a boat or when heavy weights are lifted with the davits. - breaking waves re...

  • Page 95: Launching

    91/104 launching launching recommendations 10

  • Page 96

    92/104 position of hoisting cradle and straps note: measurements are expressed in mm. 1150 4000

  • Page 97

    93/104 launching recommendations a lot of skill and care is required to commission your jeanneau boat. The proper working of all your boat's equipment is the result of the quality of the commissioning operations. In order to remain completely under guarantee in the case of any failure of parts or ma...

  • Page 99: Winter Storage

    95/104 winter storage laying up protection and maintenance 11.

  • Page 100

    96/104 laying up - take ashore all the ship's log, the ropes that are not used for mooring, the galley equipment, supplies, clothes, the safety equipment, batteries, the gas cylinder. - mark again the safety equipment, check the expiration dates, have the liferaft overhauled. - take advantage of thi...

  • Page 101

    97/104 motor the engine winterization shall be carried out by a professional. Depending on the boat location, afloat or ashore, winterization is different. Here are a few major tasks to carry out: afloat - drain the cooling system and fill it with antifreeze. - shut off the battery switches, grease ...

  • Page 103: Appendixes 1

    99/104 appendixes 1 12.

  • Page 104

    1 0 0 /1 0 4 c e rt if ic a te s o f s ta n d a rd s e p a pressure relief system deck fill 99dfpv series installation instructions 11/04 69485 rev. B save these instructions caution: the vessel manufacturer must comply with the requirements of cfr 40 1060.202. Any questions can be directed to www.A...

  • Page 105

    1 0 1 /1 0 4 1 2 integrated fuel demand valve 99ifdv series installation instructions 2/12 69487 rev. C save these instructions caution: the vessel manufacturer must comply with the requirements of cfr 40 1060.202. Any questions can be directed to www.Attwood.Com failure to follow these instructions...

  • Page 106

    1 0 2 /1 0 4 inlet control valve 99icv series installation instructions 11/04 69482 rev. B save these instructions caution: the vessel manufacturer must comply with the requirements of cfr 40 1060.202. Any questions can be directed to www.Attwoodmarine.Com failure to follow these instructions may re...

  • Page 107

    1 0 3 /1 0 4 1 2 appendixes.

  • Page 108

    104/104.