JED T440 User Manual - page 30
T440 User’s manual V096B, © JED Microprocessors Pty Ltd Jan 20
th
2015
Page 30
Optoma Group 1:
DS309, EP721 / EP723 / EP727 / EP728, EW1610 (Code 99 hex, Vol: 0->15)
Optoma Group 2a
: (0/1 cmds, no DVI/HDMI) EH300, DH1011, HD25/LV, EH501, W501, X501,
EH505, W505, EW605ST, EX605ST, EW610ST, EX610ST, TW610ST, TX610ST, EX850, EX850,
EW860, EX865, EW635, EX635, TW635, TX635, EX400,W290 No audio: PRO8000, EH7500,
TH7500, EH7700. (Code 98 hex, Vol: 0->10).
Optoma Group 2b: (0/1/2 cmds, HDMI)
PRO150S,PRO250X,EX540,TX540,EX542,TX542,EX615,TX615,EX762,TX762,EX612,TX612,
DX319,DS216,DS219,DS316,ES526,EX531,EX536,DS317,DS323,TS526,TX536,C222,
ES520,EX520,ES530,EX530,DX617,ES522,EX532,DX623,EP776,EP782W,TX778W,
EX779,TX779,EW775,TW775,EX785,TX785,TW6000,TX7000, EH500, X600, W305ST, X305ST,
W306ST, X306ST, FW5200, FX5200, S303, W303, X303, S2010, X2010, S2015, W2015, X2015,
W401, X401, ZW201ST, ZX_201ST, ZW212ST, ZX212ST (Code 90 hex, Vol: 0->10).
Optoma Group 2c: (1/2 cmds, DVI)
EP752, EP761, EP763, EP783/TX783, EP1080/TX1080.
(Code 91 hex, Vol: 0->15).
Optoma Group 2d: (1/2 cmds HDMI, DVD)
EP783, EP783/TX783, TX783 (Code 93 hex,
Vol: 0->16).
Optoma Group 2e: (0/1 cmds, HDMI)
DS327, DX327, DS329, DS550, DX550, ES550, EX550,
DS551, DX551, ES551, EX551, TS551, TX551, EX565UT, TX565UT, 565UT, EX665UST,
TX665UST, EX665UT, EW675UT, TW675UT, EX685UT, EW695UTi, W307USTi, X307USTi,
EW766W, TW766W, EX765W, TX765W
(Code 92 hex, Vol: 0->20).
Optoma Group 3a *: (1/2 cmds, DVI-A on 2)DS327/DX327,DS329/DX329,ES550,
EX550, ES551, EX551,
EW674, EX772, EX774, HD75, TXR774, TWR1693
(Code 94 hex, Vol: 0->10) Note: If DVI-A is not used as Computer 2 use code 90 (2b above)
Optoma Group 3b *: (1/2 cmds, DVI-A on 2)
DX609, EP721, EP723, EP727, EP728,
EX525ST, HD71
(Code 95 hex, Vol: 0->15) Note: If DVI-A is not used as Computer 2 use code 91 (2c above)
Optoma Group 4a **:
DH1015,
DS318, EW536, EW631, EH1020, EH1060, EH2060, EX542i,
EW762/EX762, EX784, FW5200, GT360, GT700, GT720, HD66, HD600X, PRO350W, TH1020,
TH1060, TW536
(Code 96 hex, Vol: 0->10) Note: If HDMI is not used as Computer 2 use code 90 (2b above)
Optoma Group 4b **:
GT750, EHD87, HD33, HD3300, HD82LV, HD82, HD8200, HD83,
HD8300, HD86, HD87, HD8600 (Code 97 hex, no audio)
(Optoma Group 5: See BenQ SP820 for EP771/EP772 projectors (Code 3B hex))
In the back of each “User’s Manual” is a list of channel selection messages.
See master Optoma manual/code list at:
http://www.optoma.eu/support.aspx
Group 1:
Input1 := '~0039 5' + 0D;
//Computer1 VGA1 analog-RGB
Input2 := '~0039 6' + 0D;
//Computer2 VGA2 analog-RGB
Input3 := '~0039 10' + 0D;
//Video1 Comp Video* (OPT1 swaps Video1 & Video2)
Input4 := '~0039 2' + 0D;
// DVI-D (not EW1610
)*
(OPT1 swaps Video1 & Video2)
*T440: OPT6 switch ON will use S-Video in place of DVI-D/HDMI T430: Uses DVI-D / HDMI as Video2
Input4 := '~0039 9' + 0D;
//Video2 S-Video*
Input5 := '~0039 2' + 0D;
// DVI-D (not EW1610
)
Groups 2, 3, 4:
Input1 := '~0012 5' + 0D;
//Computer1 VGA1 analog-RGB
Input2 := '~0012 6' + 0D;
//Computer2 VGA2 analog-RGB