1. DL manuals
  2. Jeep
  3. Automobile
  4. 2004 Cherokee
  5. Owner's Manual

Jeep 2004 Cherokee Owner's Manual

Summary of 2004 Cherokee

  • Page 1

    Table of contents section page 1 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 things to know before starting your vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 3 understanding the fe...

  • Page 3: Introduction

    Introduction contents m introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 ▫ roll over warning . . . . . . . . . . . . . . . . . . . . . 4 m how to use this manual . . . . . . . . . . . . . . . . . . 6 m warnings and cautions . . . . . . . . . . . . . . . . . . . 7 m vehicle identi...

  • Page 4

    Introduction thank you for selecting a jeep t grand cherokee and welcome to our worldwide family. This is a specialized utility vehicle designed for both on-road and off-road use. It can go places and perform tasks for which conventional two-wheel drive vehicles were not intended. However, on-road r...

  • Page 5

    And the narrower track, if this vehicle is out of control it may roll over when some other vehicles may not. Do not attempt sharp turns or abrupt maneuvers or other unsafe driving actions that can cause loss of vehicle control. Failure to operate this vehicle safely may result in an accident, roll o...

  • Page 6

    Note: after you read the manual, it should be stored in the vehicle for convenient reference and remain with the vehicle when sold so that the new owner will be aware of all safety warnings. When it comes to service, remember that your authorized dealer knows your vehicle best, has the factory-train...

  • Page 7

    Warnings and cautions this manual contains warnings against operating procedures which could result in an accident or bodily injury. It also contains cautions against procedures which could result in damage to your vehicle. If you do not read this entire manual you may miss important information. Ob...

  • Page 8

    Vehicle modifications / alterations warning! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death. 8 introduction.

  • Page 9: Contents

    Things to know before starting your vehicle contents m a word about your keys . . . . . . . . . . . . . . . . . .11 ▫ ignition key . . . . . . . . . . . . . . . . . . . . . . . . . .11 ▫ key-in-ignition reminder . . . . . . . . . . . . . . . .12 m sentry key immobilizer system — if equipped . .12 ▫ ...

  • Page 10

    ▫ programming additional transmitters . . . . . . . .22 ▫ transmitter battery replacement . . . . . . . . . . .22 m security alarm system — if equipped . . . . . . . . .23 ▫ to set the alarm . . . . . . . . . . . . . . . . . . . . . .23 ▫ to disarm the system . . . . . . . . . . . . . . . . . . .23 ...

  • Page 11

    A word about your keys the keys for your new vehicle are enclosed in a plastic bag with the key code number on it. If you received your keys without the bag, ask your authorized dealer to give you the number. The key code can also be obtained by your authorized dealer from your vehicle invoice. Igni...

  • Page 12

    Key-in-ignition reminder if the driver’s door is opened when the key is in the ignition and not turned to the on position, a chime will sound to remind you to remove the key. Caution! Always remove the key from the ignition, and lock all doors when leaving the vehicle unattended. Sentry key immobili...

  • Page 13

    If the skis indicator light comes on during normal vehicle operation (it has been running for longer than 10 seconds) a fault has been detected in the electronics and the vehicle should be serviced as soon as possible. Note: • the sentry key immobilizer system is not compatible with remote starting ...

  • Page 14

    Consists of programming a blank key to the vehicle electronics. A blank key is one which has never been programmed. Note: when having the sentry key system serviced, bring all vehicle keys to the dealer. Customer key programming you can program new keys to the system if you have two valid keys by do...

  • Page 15

    2. This device must accept any interference that may be received, including interference that may cause undes- ired operation. Illuminated entry the interior lights come on when you open any door. They will remain on for about 30 seconds after all doors are closed then fade to off. The lights also w...

  • Page 16

    Can be used to open the liftgate. The emergency liftgate latch release can be accessed through a snap-in cover located on the liftgate trim panel. Warning! Driving with the flipper glass open can allow poi- sonous exhaust gases into your vehicle. You and your passengers could be injured by these fum...

  • Page 17

    Door locks all doors are equipped with a slide-type interior door lock. To manually lock a door, slide the lever rearward (toward the rear of the vehicle) to the “lock” position. Once locked, the rear doors cannot be opened from the inside until the lock lever has been released. However, the front d...

  • Page 18

    Child protection locks the rear doors of your vehicle are equipped with child protection locks. If you push up on the lever on the open edge of the door it cannot be opened from the inside of the vehicle. Push the lever down to disengage the child protection locks. Warning! Avoid trapping anyone in ...

  • Page 19

    As a safety feature, the power door lock switch will not lock when the door is open and the key is in the ignition. Once locked, the rear doors cannot be opened from the inside until the lock lever has been released. However, both front doors can be opened using the inside door handle. Automatic doo...

  • Page 20

    Remote keyless entry this system allows you to lock or unlock the doors and liftgate or activate the panic alarm from distances up to about 23 feet (7 meters) using a hand held radio trans- mitter. The transmitter need not be pointed at the vehicle to activate the system. To unlock the doors and lif...

  • Page 21

    To lock the doors and liftgate press and release the “lock” button on the key fob to lock all doors and liftgate. If you wish, the horn can be programmed to chirp once and/or the turn signals can be programmed to flash once to show the system is acti- vated. For customer programmable features, refer...

  • Page 22

    Programming additional transmitters up to four transmitters can be programmed. See your authorized dealer. Transmitter battery replacement the recommended replacement battery is a panasonic cr2016 or equivalent. Note: do not touch the battery terminals that are on the back housing or the printed cir...

  • Page 23

    4. Reset the transmitter by pressing the “unlock” button six times. Test the transmitter operation. Security alarm system — if equipped this system monitors the vehicle doors, liftgate, liftgate flipper glass, and ignition for unauthorized operation. When the alarm is activated, the system provides ...

  • Page 24

    Transmitter to disarm the system. You may also acciden- tally disarm the system by unlocking the driver’s door with the key and then locking it. The door will be locked but the security alarm will not arm. Power windows the power window controls are located on the driver’s door trim panel. There is ...

  • Page 25

    The window lock switch located next to the power door lock switch allows you to disable the rear passenger window switches that are located on the rear door trim panels. Auto down feature — if equipped the driver’s door window switch has an “auto down” feature. Press the window switch past the deten...

  • Page 26

    Open or partially open positions. This is a normal occur- rence and can be minimized. If the buffeting occurs with the sunroof open, adjust the sunroof opening to minimize the buffeting. Occupant restraints some of the most important safety features in your vehicle are the restraint systems. These i...

  • Page 27

    Research has shown that seat belts save lives, and they can reduce the seriousness of injuries in a collision. Some of the worst injuries happen when people are thrown from the vehicle. Seat belts reduce the possibility of ejection and the risk of injury caused by striking the inside of the vehicle....

  • Page 28

    Lap/shoulder belt operating instructions 1. Enter the vehicle and close the door. Sit back and adjust the seat. 2. The seat belt latch plate is above the back of your seat. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to make the belt go aroun...

  • Page 29

    Warning! • a belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • a belt that is too loose will not protect you as well. In a sudden stop ...

  • Page 30

    5. Position the shoulder belt on your chest so that it is comfortable and not resting on your neck. The retractor will withdraw any slack in the belt. 6. To release the belt, push the red button marked press on the buckle. The belt will automatically retract to its stowed position. If necessary, sli...

  • Page 31

    As a guide, if you are shorter than average, you will prefer a lower position, and if you are taller than average, you’ll prefer a higher position. When you release the anchorage, try to move it up or down to make sure that it is locked in position. Automatic locking mode — if equipped in this mode,...

  • Page 32

    How to disengage the automatic locking mode disconnect the combination lap/shoulder belt and allow it to retract completely to disengage the automatic lock- ing mode and activate the vehicle sensitive (emergency) locking mode. Energy management feature this vehicle has a safety belt system with an e...

  • Page 33

    Rear center lap belt the rear center seating position has a lap belt only. To fasten the lap belt, slide the latch plate into the buckle until you hear a “click.” to lengthen the lap belt, tilt the latch plate and pull. To remove slack, pull the loose end of the webbing. Wear the belt snug against t...

  • Page 34

    Note: the following steps must occur within the first 60 seconds of the ignition switch being turned to the on or start position. The manufacturer does not recom- mend deactivating the enhanced warning system (beltalert). 1. Turn the ignition switch to the off position, and fasten the driver’s seat ...

  • Page 35

    Seat belt extender if a seat belt is too short, even when fully extended and when the adjustable upper shoulder belt anchorage (if equipped) is in its lowest position, your authorized dealer can provide you with a seat belt extender. This extender should be used only if the existing belt is not long...

  • Page 36

    The instrument panel, above the glove compartment. The words srs/airbag are embossed on the airbag covers. Note: the front airbags are certified to the federal regulations that allow less forceful deployment. The front airbags have a multi stage inflator design. This allows the airbag to have differ...

  • Page 37

    Warning! • do not put anything on or around the front airbag covers or attempt to manually open them. You may damage the airbags and you could be injured be- cause the airbags are not there to protect you. These protective covers for the airbag cushions are de- signed to open only when the airbags a...

  • Page 38

    1. Children 12 years and under should always ride buckled up in a rear seat. Infants in rear facing child restraints should never ride in the front seat of a vehicle with a passenger airbag. An airbag deplyment could cause severe injury or death to infants in that position. Children that are not big...

  • Page 39

    Warning! • relying on the airbags alone could lead to more severe injuries in a collision. The airbags work with your seat belt to restrain you properly. In some collisions the airbags won’t deploy at all. Always wear your seat belts even though you have airbags. • being too close to the steering wh...

  • Page 40

    How the airbag system works • the airbag control module (acm) determines if a frontal collision is severe enough to require the airbags to inflate. Based on the level of collision severity, the front control module determines the proper rate of inflation. The front airbag inflators are designed to p...

  • Page 41

    Units. A large quantity of nontoxic gas is generated to inflate the front airbags. Different airbag inflation rates are possible, these rates are determined by the front airbag control module based on collision severity. The steering wheel hub trim cover and the upper right side of the instrument pa...

  • Page 42

    If a deployment occurs the airbag system is designed to deploy the airbags when the impact sensors detect a moderate-to-severe frontal collision, to help restrain the driver and front passenger, and then immediately deflate. Note: a frontal collision that is not severe enough to need airbag protecti...

  • Page 43

    Warning! Deployed airbags can’t protect you in another colli- sion. Have the airbags replaced by an authorized dealer as soon as possible. Maintaining your airbag system warning! • modifications to any part of the airbag system could cause it to fail when you need it. You could be injured if the air...

  • Page 44

    Airbag warning light you will want to have the airbag system ready to inflate for your protection in an impact. The airbag system is designed to be maintenance free. If any of the following occurs, have an authorized dealer service the system promptly: • does not come on during the 6 to 8 seconds af...

  • Page 45

    Enough for an adult seat belt. Always check the child seat owner’s manual to ensure you have the right seat for your child. Use the restraint that is correct for your child: • the rearward-facing infant restraint is for babies weighing up to about 20 lbs (9 kg), and one year old or more. The infant ...

  • Page 46

    • for additional information, refer to www.Seatcheck.Org. Warning! • improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the manufacturer’s directions ex- actly when installing an infant or ...

  • Page 47

    • the passenger seat belts are equipped with cinching latch plates, which are designed to keep the latch portion tight around the child restraint so that it is not necessary to use a locking clip. Pulling up on the shoulder portion of the lap/shoulder belt will tighten the belt. The cinching latch p...

  • Page 48

    Anchors and tethers for children. The latch system provides for the installation of the child restraint without using the vehicle seat belt. The two rear outboard seating positions have exclusive lower anchorages located at the rear of the seat cushion. They are round bars, part of the seat and body...

  • Page 49

    And between the two posts. Attach the tether strap hook to the anchor loop. Install the child restraint according to the manufacturer’s instructions, and tighten the vehicle seat belt. Remove the slack from the tether strap accord- ing to the manufacturer’s instructions. Child restraints systems hav...

  • Page 50

    In general, you will first loosen the adjusters on the lower and tether straps so that you can more easily attach the hook or connector to the lower and tether anchorages. The tether strap should be routed under the center of the head restraint and attached to the tether anchor above the rear liftga...

  • Page 51

    Engine break-in recommendations a long break-in period is not required for the engine in your new vehicle. Drive moderately during the first 300 miles (500 km). After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable. While cruising, brief full-throttle accelerat...

  • Page 52

    Garage, and never sit in a parked vehicle with the engine running for a extended period. If the vehicle is stopped in an open area with engine running for more than a short period, adjust the ventilation system to force fresh, outside air into the vehicle. • guard against carbon monoxide with proper...

  • Page 53

    Defrosters check operation by selecting the defrost mode and place the blower control on high speed. You should feel the air directed against the windshield. Safety checks you should make outside the vehicle tires examine tires for excessive tread wear or uneven wear patterns. Check for stones, nail...

  • Page 55: Contents

    Understanding the features of your vehicle contents m mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59 ▫ inside day/night mirror . . . . . . . . . . . . . . . . .59 ▫ inside automatic dimming mirror — if equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . .60 ▫ exte...

  • Page 56

    M lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75 ▫ interior lighting . . . . . . . . . . . . . . . . . . . . . . .75 ▫ front map/reading lights . . . . . . . . . . . . . . .75 ▫ multi-function control lever . . . . . . . . . . . . . .76 ▫ battery saver feature—exterior/inte...

  • Page 57

    ▫ to resume speed . . . . . . . . . . . . . . . . . . . . . .87 ▫ to vary the speed setting . . . . . . . . . . . . . . . .87 ▫ to accelerate for passing . . . . . . . . . . . . . . . .87 ▫ driving up or down hills . . . . . . . . . . . . . . .88 m overhead console . . . . . . . . . . . . . . . . . ...

  • Page 58

    M glove compartment . . . . . . . . . . . . . . . . . . . . . 116 m cup holders . . . . . . . . . . . . . . . . . . . . . . . . . . 116 m cargo area features . . . . . . . . . . . . . . . . . . . . . 118 ▫ cargo light . . . . . . . . . . . . . . . . . . . . . . . . . 118 ▫ retractable cargo area cov...

  • Page 59

    Mirrors inside day/night mirror the mirror should be adjusted to center on the view through the rear window. A two-point pivot system allows for horizontal and vertical adjustment of the mirror. The mirror should be adjusted while set in the day position (toward windshield). Annoying headlight glare...

  • Page 60

    Inside automatic dimming mirror — if equipped this mirror automatically adjusts for annoying headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light in the button will indicate when the dimming feature is activated. Cauti...

  • Page 61

    Exterior mirrors folding feature all exterior mirrors are hinged and may be moved either forward or rearward to resist damage. The hinges have three detent positions; full forward, full rearward, and normal. Outside mirrors to receive maximum benefit, adjust the outside mirrors to center on the adja...

  • Page 62

    Set the top switch to the left or right for the left or right mirror, and set it to the center off position to prevent accidentally moving a mirror when you are finished adjusting the mirror. To adjust a mirror, select left or right with the top switch, and press one of the four arrows for the direc...

  • Page 63

    Seats warning! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust any seat only while the vehicle is parked. Front manual seat adjustment move the se...

  • Page 64

    Warning! • it is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • be...

  • Page 65

    Power seat adjuster — if equipped warning! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt and be seriously injured or even fatally injured. Use the recliner only when the vehicle is parked. ...

  • Page 66

    This seat also has a manual recline lever located just to the rear of the power seat switch. Pull up on the lever to recline the seat. 10–way power seat with power recliner and power lumbar — if equipped these seat switches are located on the outboard side of the seat near the floor. Use these switc...

  • Page 67

    Caution! Do not put anything under a power seat. It may cause damage to the seat controls. Power lumbar the power lumbar control is located on the outboard side of the seat. Use this switch to increase or decrease the desired amount of lumbar support. Understanding the features of your vehicle 67 3.

  • Page 68

    Power reclining seat the recliner control is on the outboard side of the seat. Use this switch to recline the seatback and to return the seatback to the upright position. Warning! Do not ride with the seatback reclined so that the seat belt is no longer resting against your chest. In a collision you...

  • Page 69

    The memory position buttons located on the driver’s door will always recall stored settings. The remote keyless entry transmitters can be programmed to recall positions when the “unlock” button is pressed. For customer programmable features refer to the section on “overhead console” for programming ...

  • Page 70

    2. Press the memory button “1” if you are setting the memory for driver one or number “2” if you are setting the memory for driver two. 3. Adjust the seat, recliner, and driver’s outside rear view mirrors to the desired position. 4. Set the radio station presets as you desire (up to 10 am and 10 fm ...

  • Page 71

    Heated seats — if equipped this feature heats the driver’s and passenger’s front seats. The controls for the heated seats are located on the instrument panel below the heater/air conditioning con- trols. After turning on the ignition you can choose from hi, off, or lo heat settings. An indicator on ...

  • Page 72

    To fold the 60/40 rear seat perform the following steps: 1. Use the pull straps available on each seat cushion section; pull the strap forward and pivot the cushion forward flush with the front seatback. 2. Remove the headrests from the rear seatback. Press the button and pull the headrest from the ...

  • Page 73

    Note: when lifting up on the release handle, the seatback will release easier if you do not pull forward on the seatback; only lift up on the release handle until the seatback disengages, then fold the seat forward. To restore the 60/40 rear seat to the upright position perform the following steps: ...

  • Page 74

    To open and close the hood to open the hood, pull the release lever inside your vehicle located below the instrument panel and in front of the driver’s door. Then reach under the hood and pull upward on the safety latch and lift the hood. To prevent possible dam- age, do not slam the hood to close i...

  • Page 75

    Warning! If the hood is not fully latched, it could fly up when the vehicle is moving and block your forward vision. Be sure all hood latches are fully latched before driving. Lights interior lighting the interior lighting consists of courtesy lights mounted below the instrument panel, an overhead c...

  • Page 76

    Multi-function control lever the multi-function control lever controls the operation of the headlights, turn signals, headlight beam selection, instrument panel light dimming, passing light, interior courtesy/dome lights, and optional fog lights. Battery saver feature—exterior/interior lights if the...

  • Page 77

    Headlights and parking lights turn the end of the multi-function control lever to the first detent for parking light operation. Turn to the second detent for headlight operation. Turn to the third detent for “auto” headlights operation (if equipped). Automatic headlight system — if equipped turn the...

  • Page 78

    To turn this feature on or off. Also, refer to “windshield wipers and washers” in this section for more information note: when your headlights come on during the daytime, the instrument panel lights will automatically dim to the lower nighttime intensity. Refer to “instru- ment panel and interior li...

  • Page 79

    Fog lights — if equipped the fog light switch is located in the multi- function control lever. To activate the fog lights, turn on the park/turn lights, low beam headlights, or auto headlights and pull out the end of the multi- function control lever. A light in the instrument cluster shows when the...

  • Page 80

    Headlight time delay there is also a feature that delays turning off the vehicle lights for 30, 60, or 90 seconds after the ignition switch is turned off. To activate the headlight delay, the multi- function control lever must be rotated to the “off” position after the ignition switch is turned off....

  • Page 81

    Delay range, the wiper will operate for several seconds after the lever is released, and then resume the intermit- tent interval previously selected. If the lever is pulled while in the off position, the wipers will operate for several wipe cycles, then turn off. Warning! Sudden loss of visibility t...

  • Page 82

    Rain sensitive wiper system — if equipped the rain sensitive wiper system provides you with the convenience of automatically detecting moisture on your windshield and turning on the wipers at the appropriate speed. The rain sensor is located above the rear view mirror and reacts to any moisture pres...

  • Page 83

    Note: since the rain sensor is designed to detect moisture, road spray, smashed bugs, and moisture from passing trucks may occasionally cause the wipers to cycle if the lever is in auto. Also, manual intervention may be necessary under certain conditions: additional wipes may be desired, in foggy/mi...

  • Page 84

    Tilt steering column to tilt the column, pull the small lever, located behind the turn signal control, toward you and move the wheel up or down, as desired. Release the lever to lock the wheel firmly in place. Warning! Tilting the steering wheel column while the vehicle is moving is dangerous. Witho...

  • Page 85

    Press the top of the button to move the pedals rearward (toward the front of the vehicle). Press the bottom of the button to move the pedals forward (toward the driver). • the pedals can be adjusted with the ignition off. • the pedals can be adjusted while driving. • the pedals cannot be adjusted wh...

  • Page 86

    Electronic speed control when engaged, this device takes over accelerator opera- tions at speeds greater than 40 mph (60 km/h). The controls are mounted on the steering wheel and consist of on·off, set, res·accel, cancel, and coast con- trols. To activate press the on·off button to turn the system o...

  • Page 87

    To resume speed to resume a previously set speed, press and release the res·accel button. Resume can be used at any speed above 30 mph (48 km/h). To vary the speed setting when the speed control is on, speed can be increased by pressing and holding the res·accel button. When the button is released, ...

  • Page 88

    Warning! Leaving the speed control on when not in use is dangerous. You could accidentally set the system or cause it to go faster than you want. You could lose control and have an accident. Always leave the system off when you aren’t using it. Driving up or down hills when going up or down hills, i...

  • Page 89

    Overhead console the overhead console contains dome/reading lights, an optional universal garage door opener (homelink t), an optional sunroof switch, and an electronic vehicle infor- mation center (evic) that consists of the following: • compass/temperature display • trip information displays • veh...

  • Page 90

    The dome/reading lights illuminate when a door or the liftgate is opened or when the interior lights are turned on by rotating the dimmer control located on the multi- function lever. The reading lights are activated by pressing on the recessed area of the corresponding lens. Note: the dome/reading ...

  • Page 91

    • perform service • door open (one or more, with graphic) • liftgate open (with graphic) • liftglass open (with graphic) • washer fluid low (with graphic) • memory seat disabled • memory #1 positions set • memory #2 positions set • pedal adjust disabled • left front low pressure • left front high pr...

  • Page 92

    Tire pressure monitor system — if equipped the tire pressure monitor (tpm) system uses wireless technology to monitor tire pressure levels. Sensors, mounted to each wheel as part of the valve stem transmit tire pressure readings to a receiver located in the over- head console. The tire pressure is s...

  • Page 93

    1. If any tire pressure has exceeded the low or high pressure (refer to starting and operating — tires and wheels), the tpm system will display a message in the evic and sound a chime. It will then go into the tire pressure display screen and flash the pres- sure value of the tire that is low or hig...

  • Page 94

    When valid tire pressure sensor messages have been received from all 4 road tires. Tpm system function is temporarily unavailable due to external electromagnetic interference, such as electronic devices or nearby radio or tv towers. 4. In addition to monitoring the vehicle tires, the tpm system moni...

  • Page 95

    General information this device complies with fcc rules part 15 and with rss-210 of industry canada. Operation is subject to the following conditions: 1. This device may not cause harmful interference 2. This device must accept any interference that may be received, including interference that may c...

  • Page 96

    Display selects english, francais, deutsch, italiana, or espanol. As you continue the displayed information will be shown in the selected language. Display u.S. Or metric? Pressing the step button when in this display selects us or metric. The overhead console and instrument panel displays will be i...

  • Page 97

    The liftgate will unlock at the first press of the remote keyless entry unlock button. Pressing the step button when in this display will select driver’s door 1st or all doors. Remote linked to memory? (available with memory seat only) when this feature is selected the memory seat, mirror, and radio...

  • Page 98

    Headlights will turn on when the wipers are turned on. The headlights will also turn off when the wipers are turned off if they were turned on in this way. Pressing the step button when in this display will select “yes” or “no.” note: turning the headlights on during the daytime causes the instrumen...

  • Page 99

    To memory is set to yes) when the remote keyless entry transmitter is used to unlock the door. Pressing the step button when in this display will select “yes” or “no.” retrain tire sensors? (available with tpm system only) when this feature is selected, the tpm system will start the retraining proce...

  • Page 100

    Note: there is a 60 second timer for training the first tire and a 30 second timer between training the remain- ing tires. If either of these timers expire, the evic will abort the training procedure. 6. Starting at the left front tire, place the training magnet over the valve stem until the horn ch...

  • Page 101

    8. Return magnet to storage location. If the display reads training complete, pressing either the step, c/t, reset, or menu buttons will exit the training mode. If the display reads training aborted, move the vehicle ahead at least 1 foot and complete steps 1–8 again. For further assistance, questio...

  • Page 102

    102 understanding the features of your vehicle.

  • Page 103

    Trip computer this feature, located in the overhead console, displays the following information when the display is in the “compass/ temperature” mode and the step button is pressed: step button press the step button to cycle through all of the compass/mini-trip computer displays. Average fuel econo...

  • Page 104

    Tire pressure display — if equipped shows the current pressure of all 4 road tires. Note: tires heat up during normal driving conditions. Heat will cause the tire pressure to increase from 2 to 6 psi (14 to 41 kpa) during normal driving conditions. Refer to “tire inflation pressures” in section 5 fo...

  • Page 105

    Note: to ensure proper compass calibration, make sure the compass variance is properly set before manu- ally calibrating the compass. Refer to variance map. To put into a calibration mode turn on the ignition and set the display to “compass/ temperature.” press and hold the reset button to change th...

  • Page 106

    To set the variance: turn the ignition on and set the display to “compass/temperature.” press the reset button approximately five seconds. The last variance zone number will be displayed. Press the step button to select the new variance zone and press the reset button to resume normal operation. Gar...

  • Page 107

    Warning! Before programming homelink to a garage door opener or gate operator, make sure that people and objects are out of the way of the device to prevent potential harm or damage. When programming a garage door opener, it is advised to park outside of the garage. Do not use homelink with any gara...

  • Page 108

    Programming homelink note: it is recommended that a new battery be placed in the hand-held transmitter of the device being pro- grammed to homelink for quicker training and accurate transmission of the radio frequency signal. Warning! Vehicle exhaust contains carbon monoxide, a danger- ous gas. Do n...

  • Page 109

    After a short time, the message training will show on homelink display. Do not release the buttons until the next step has been completed. 3. When the message trained appears on the homelink display, release both the homelink and hand- held transmitter buttons. Note: if the homelink display does not...

  • Page 110

    5. At the garage door opener receiver (motor-head unit) in the garage, locate the 9learn9 or 9smart9 button. This can usually be found where the hanging antenna wire is attached to the motor-head unit. 6. Firmly press and release the 9learn9 or 9smart9 button. (the name and color of the button may v...

  • Page 111

    Gate operator/canadian programming canadian radio-frequency laws require transmitter sig- nals to 9time-out9 (or quit) after several seconds of transmission - which may not be long enough for homelink to pick up the signal during programming. Similar to this canadian law, some u.S. Gate operators ar...

  • Page 112

    Power sunroof — if equipped the sunroof is electrically operated from a switch located in the overhead console. To operate the sunroof, the ignition switch must be in the on or acc position. The sunroof has “manual” and “express open” modes of operation when opening. Express open mode to open the su...

  • Page 113

    Closing operation to close the sunroof from an open position, press the switch forward and hold it until the sunroof glass comes to a complete stop. Releasing the switch at any time in this mode will cause the sunroof to stop at the current position. Vent operation opening the glass panel to the ven...

  • Page 114

    Sunshade operation the sunshade covering the glass in the panel will open with the sunroof and must be closed manually. It can also be opened and closed manually without activating the sunroof. This will allow you to enjoy the warmth of the sun during the winter months. Warning! In an accident, ther...

  • Page 115

    Power outlet to the right of the convenience tray (lower center of instrument panel) is an outlet for electrically powered accessories. Pull lightly on the tab of the plastic cover to access the outlet. There is a rear power outlet located in the right rear cargo area rearward of the storage bin/cd ...

  • Page 116

    Caution! Electrical outlet use with engine off • many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.E., cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or ...

  • Page 117

    Note: the cup holder insert is removable, from the console, for cleaning. It can be reinstalled with the larger cup depression towards the passenger seat, but the top surface will not be flush with the console surface. The rear passengers have access to two cup holders that pull out from the rear of...

  • Page 118

    Cargo area features cargo light the cargo area light is activated by opening the liftgate, opening any door, or by rotating the dimmer control on the multi-function control lever to the extreme top posi- tion. If all doors are closed and only the liftgate is open, pushing on the cargo light lens sur...

  • Page 119

    Warning! In an accident a cargo cover loose in the vehicle could cause injury. It could fly around in a sudden stop and strike someone in the vehicle. Do not store the cargo cover on the cargo floor or in the passenger compartment. Remove the cover from the vehicle when taken from its mounting. Do n...

  • Page 120

    Warning! • cargo tie-down hooks are not safe anchors for a child seat tether strap. In a sudden stop or colli- sion a hook could pull loose and allow the child seat to come loose. A child could be badly injured. Use only the anchors provided for child seat tethers. • the weight and position of cargo...

  • Page 121

    Roof luggage rack external racks do not increase the total load carrying capacity of the vehicle. Be sure that the total occupant and luggage load inside the vehicle, plus the load on the luggage rack, do not exceed the rated vehicle capacity. This vehicle is not equipped with roof rack cross rails ...

  • Page 122

    Warning! Cargo must be securely tied before driving your vehicle. Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in personal injury or property damage. Follow the roof rack “cautions” when carrying cargo on your roof rack. 122 understanding the features of y...

  • Page 123: Contents

    Understanding your instrument panel contents m instrument panel and interior controls . . . . . . . 126 m instrument cluster . . . . . . . . . . . . . . . . . . . . . . 127 ▫ instrument cluster — if equipped . . . . . . . . . 128 m instrument cluster description . . . . . . . . . . . . . 129 m elect...

  • Page 124

    M sales code rbp—am & fm stereo radio with cassette tape player, cd player, and optional cd/dvd changer controls . . . . . . . . . . . . . . . 143 ▫ radio operation . . . . . . . . . . . . . . . . . . . . . . 143 ▫ tape player operation . . . . . . . . . . . . . . . . . . 147 ▫ cd player operation ....

  • Page 125

    M remote sound system controls — if equipped . . 160 ▫ radio operation . . . . . . . . . . . . . . . . . . . . . . 161 ▫ tape player . . . . . . . . . . . . . . . . . . . . . . . . . 161 ▫ cd player — single disc in radio . . . . . . . . . 162 ▫ cd player — 10 disc in cargo area . . . . . . . . 162 ...

  • Page 126

    Instrument panel and interior controls 126 understanding your instrument panel.

  • Page 127

    Instrument cluster understanding your instrument panel 127 4.

  • Page 128

    Instrument cluster — if equipped 128 understanding your instrument panel.

  • Page 129

    Instrument cluster description 1. Voltmeter indicates available battery voltage and charging system operation. The lower red zone shows that the battery charge may be too low to start the engine. With the engine running, the normal operating range is between 11 and 15 volts. Prolonged gage readings ...

  • Page 130

    7. Oil pressure gage indicates the engine oil pressure. This gage does not measure oil level. Pressure varies with engine speed, temperature, and oil viscosity. Normal oil pressure will be midway between the lowest and highest limit marks. 8. Sentry key indicator light — if equipped refer to “sentry...

  • Page 131

    Either too high or too low. Examine the gages carefully, and follow the instructions above for each indicated problem. Note: when the ignition switch is turned to off, the fuel gage, voltmeter, oil pressure, and temperature gages will not show any readings. When the engine is not running, turn the i...

  • Page 132

    Caution! Driving with a hot cooling system could damage your vehicle. If the temperature gage reads high, pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains in the high range, turn the engine...

  • Page 133

    18. Seat belt indicator light when the ignition switch is first turned on, this light will turn on for 5 to 8 seconds as a bulb check. During the bulb check, if the driver’s seat belt is unbuckled, a chime will sound. After the bulb check or when driving, if the driver seat belt remains unbuckled, t...

  • Page 134

    21. Low fuel warning light when the fuel level reaches approximately 1.5 u.S. Gallons (6l) this light will come on and remain on until fuel is added. The “low fuel warning light” may turn on and off again, especially during and after hard braking, accelerations, or turns. This occurs due to the shif...

  • Page 135

    Electronic digital clock the clock and radio each use the display panel built into the radio. A digital readout shows the time in hours and minutes whenever the ignition switch is in the on or acc position and the time button is pressed. When the ignition switch is in the off position, or when the r...

  • Page 136

    Electrical disturbances radio waves may pick up electrical disturbances during transmission. They mainly affect the wave amplitude, and thus remain a part of the am reception. They interfere very little with the frequency variations that carry the fm signal. Am reception am sound is based on wave am...

  • Page 137

    Note: power to operate the radio is supplied through the ignition switch. It must be in the on or acc position to operate the radio. Seek press and release the seek button to search for the next station in either the am or fm mode. Press the top of the button to seek up and the bottom to seek down. ...

  • Page 138

    Am/fm selection press the am/fm button to change from am to fm. The operating mode will be displayed next to the station frequency. The display will show st when a stereo station is received. To set the radio push-button memory when you are receiving a station that you wish to commit to push-button ...

  • Page 139

    Note: changes or modifications not expressively ap- proved by the party responsible for compliance could void the user’s authority to operate the equipment. Cd player operation note: the ignition switch must be in the on or acc position and the volume control on before the cd player will operate. In...

  • Page 140

    If you do not remove the disc within 15 seconds, it will be reloaded. The unit will continue in radio mode. The disc can be ejected with the radio and ignition off. Ff/tune/rw press ff (fast forward) and the cd player will begin to fast forward until ff is released. The rw ( reverse) button works in...

  • Page 141

    Mode button to activate the cd changer, press the mode button until cd information appears on the display. Push-button while the cd changer is playing, press the number 1 push-button or the number 5 push-button to select a disc numbered higher or lower than the one currently being played. Seek butto...

  • Page 142

    An err symbol will appear on the display if the laser is unable to read the disc data for the following reasons: • excessive vibration • disc inserted upside down • damaged disc • water condensation on optics radio display messages your radio has been designed to display certain messages when a prob...

  • Page 143

    Sales code rbp—am & fm stereo radio with cassette tape player, cd player, and optional cd/dvd changer controls radio operation power/volume control press the on/vol control to turn the radio on. Turn the volume control to the right to increase the volume. Note: power to operate the radio is supplied...

  • Page 144

    Program type radio display jazz jazz foreign language language news news nostalgia nostalga oldies oldies personality persnlty public public rhythm and blues r & b religious music rel musc religious talk rel talk rock rock soft soft soft rock soft rck soft rhythm and blues soft r&b sports sports tal...

  • Page 145

    Seek press and release the seek button to search for the next station in either the am or fm mode. Press the top of the button to seek up and the bottom to seek down. The radio will remain tuned to the new station until you make another selection. Holding the button in will by- pass stations without...

  • Page 146

    To set the radio push-button memory when you are receiving a station that you wish to commit to push-button memory, press the set button. Set 1 will now show in the display window. Select the “1–5” button you wish to lock onto this station and press and release that button. If a button is not select...

  • Page 147

    Tape player operation insert the cassette with the exposed tape side toward the right and the mechanical action of the player will gently pull the cassette into the play position. Note: when subjected to extremely cold temperatures, the tape mechanism may require a few minutes to warm up for proper ...

  • Page 148

    Rewind — rw press the rw button down momentarily to reverse the tape direction. The tape will rewind until the button is pressed again or until the beginning of the tape is reached. At the beginning of the tape, the tape will play in the opposite direction. Ejt tape press the ejt tape button and the...

  • Page 149

    Cd player operation note: the ignition switch must be in the on or acc position and the volume control on before the cd player will operate. Inserting the compact disc you may either insert or eject a disc with the radio off. If you insert a disc with the ignition on and the radio off, the display w...

  • Page 150

    Ff/tune/rw press ff (fast forward) and the cd player will begin to fast forward until ff is released. The rw (reverse) button works in a similar manner. Random play — rnd/program button 4 press the rnd (button 4) button while the cd is playing to activate random play. This feature plays the selectio...

  • Page 151

    Disc up/program button 1 press the disc (button 1) button to play the next avail- able disc. Random play — rnd/program button 4 press the rnd (button 4) button while the cd is playing to activate random play. This feature plays the selections on the currently playing compact disc in random order to ...

  • Page 152

    Sales code rb1—am/fm stereo radio with dvd/gps navigation system the navigation system provides maps, turn identifica- tion, selection menus and instructions for selecting a variety of destinations and routes. Refer to your “navi- gation user’s manual” for detailed operating instruc- tions. Satellit...

  • Page 153

    Electronic serial number/sirius identification number (ens/sid) the electronic serial number/sirius identification num- ber is needed to activate your sirius satellite radio system. To access the esn/sid, refer to the following steps: esn/sid access with rbb and rbk radios with the ignition switch i...

  • Page 154

    Selecting satellite mode in rbp, rbu, raz, and rbq radios press the mode button repeatedly until the word 9sirius9 appears in the display. These radios will also display the following: • after 3 seconds, the current channel name and channel number will be displayed for 5 seconds. • the current progr...

  • Page 155

    Storing and selecting pre-set channels in addition to the 10 am and 10 fm pre-set stations, you may also commit 10 satellite stations to push button memory. These satellite channel pre-set stations will not erase any am or fm pre-set memory stations. Follow the memory pre-set procedures that apply t...

  • Page 156

    Reception quality satellite reception may be interrupted due to one of the following reasons. • the vehicle is parked in an underground parking structure or under a physical obstacle. • dense tree coverage may interrupt reception in the form of short audio mutes. • driving under wide bridges or alon...

  • Page 157

    1. Open the cd changer compartment located in the right rear cargo area. 2. Slide the cd changer door all the way to the right. 3. Press the eject button. Understanding your instrument panel 157 4.

  • Page 158

    4. Gently remove the magazine by pulling it up and out of the cd changer. 5. Close the cd changer door by sliding it to the left. Loading discs into the magazine gently slide the discs into the magazine with the disc label in the direction indicated on the magazine label (up to 10 discs). If the dis...

  • Page 159

    Note: do not use 3 inch (8 cm) discs in the magazine. If a cd adaptor for 3 inch (8 cm) discs is used, the disc will not be ejected. Removing discs from the magazine to remove the disc, gently press on the exposed edge of the disc. There is a light spring tension holding the disc in place. Note: do ...

  • Page 160

    3. Insert the magazine into the changer slot with the writing on the magazine label facing in the same direc- tion as the word jeep t on the changer door (disc loading slots facing to the right). 4. Slide the changer door to the left to close the changer door. Remote sound system controls — if equip...

  • Page 161

    Mode of the sound system. Pressing the top of the rocker switch will increase the volume and pressing the bottom of the rocker switch will decrease the volume. Pressing the center button will make the radio switch between the various modes available (am/fm/tape/ cd, etc.). The left hand control is a...

  • Page 162

    Cd player — single disc in radio pressing the top of the switch once will go to the next track on the cd. Pressing the bottom of the switch once will go to the beginning of the current track or to the beginning of the previous track if it is within one second after the current track begins to play. ...

  • Page 163

    3. Keep the cassette tape away from direct sunlight, heat and magnetic fields such as the radio speakers. 4. Before inserting a tape, make sure that the label is adhering flatly to the cassette. 5. A loose tape should be corrected before use. To rewind a loose tape, insert the eraser end of a pencil...

  • Page 164

    6. Do not expose the disc to direct sunlight. 7. Do not store the disc where temperatures may become too high. Radio operation and cellular phones under certain conditions, the cellular phone being on in your vehicle can cause erratic or noisy performance from your radio. This condition may be lesse...

  • Page 165

    Blower control the rotary knob on the left controls the blower and can be set in one of four positions from lo to hi. The blower fan motor will remain on un- til the system is turned to the off position or the ignition is turned off. Temperature control the degree of comfort can be selected by rotat...

  • Page 166

    Mode selection the mode selector (the right rotary knob) can be set in any of the following positions: off this position turns off the blower motor and outside air will not pass through any outlets. Recirculation the recirculation feature can be selected with the mode control knob. Outside air is no...

  • Page 167

    Defrost/floor air flows through the front and rear floor outlets and the outlets at the base of the windshield. Defrost air is directed to the windshield through the outlets at the base of the windshield. Note: to improve fuel economy, leave in defrost only when necessary. Infrared dual-zone climate...

  • Page 168

    Level is displayed the system will maintain that level automatically using the heating system. Should the de- sired comfort level require air conditioning, the system will automatically make the adjustment. You may notice the blower speed getting lower as the difference between the driver and passen...

  • Page 169

    • floor air flows through the floor outlets located under the instrument panel and into the rear seating area through vents under the front seats. • bi-level air flows both through the outlets located in the instrument panel and those located on the floor. • panel air flows through the outlets locat...

  • Page 170

    Off until the engine warms up. However, the fan will engage immediately if the defrost mode is selected or if you select a fixed blower speed. Window fogging vehicle windows tend to fog on the inside in mild rainy or humid weather. To clear the windows, use the a/c, panel, and blower controls. Direc...

  • Page 171

    If the liftgate flipper glass is open, connection to the rear window wiper is interrupted preventing activation of the rear wiper blade. When the liftgate flipper glass is closed, the rear wiper switch or the ignition switch needs to be turned off and on to restart the rear wiper. Adding washer flui...

  • Page 172

    The defroster will automatically turn off after about ten minutes. For about five more minutes of operation, push the button again. To prevent excessive battery drain, use the defroster only when the engine is operating. The push button also activates the heated exterior mirrors, if so equipped. Cau...

  • Page 173: Starting And Operating

    Starting and operating contents m starting procedures . . . . . . . . . . . . . . . . . . . . . 176 ▫ normal starting . . . . . . . . . . . . . . . . . . . . . . 176 ▫ extreme cold weather (below –20°f (–29°c) . . 177 ▫ if engine fails to start . . . . . . . . . . . . . . . . . 177 ▫ after starting ...

  • Page 174

    ▫ selec-tract operating instructions/precautions . . . . . . . . . . . . . . . . 186 ▫ shift positions . . . . . . . . . . . . . . . . . . . . . . . . 188 ▫ shifting procedure . . . . . . . . . . . . . . . . . . . . 189 ▫ quadra-trac iit operating instructions/precautions — if equipped . . . . . 191...

  • Page 175

    ▫ tire spinning . . . . . . . . . . . . . . . . . . . . . . . . 214 ▫ tread wear indicators . . . . . . . . . . . . . . . . . . 215 ▫ replacement tires . . . . . . . . . . . . . . . . . . . . . 215 ▫ alignment and balance . . . . . . . . . . . . . . . . . 217 m tire pressure monitor system — if equi...

  • Page 176

    Starting procedures before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. Warning! Do not leave children or animals inside parked vehicles in hot weather. Interior heat build up may cause serious injury or death. The gear selector must be...

  • Page 177

    Warning! Never pour fuel or other flammable liquids into the throttle body air inlet opening in an attempt to start the vehicle. This could result in a flash fire causing serious personal injury. Extreme cold weather (below –20°f (–29°c) to insure reliable starting at these temperatures, use of an e...

  • Page 178

    After starting the idle speed will automatically decrease as the engine warms up. Caution! Long periods of engine idling, especially at high engine speeds can cause excessive exhaust tempera- tures which can damage your vehicle. Do not leave your vehicle unattended with the engine running. Engine bl...

  • Page 179

    Automatic transmission the pointer on the selector indicates the transmission gear range (selector is illuminated for night driving). Start the engine with the selector lever in n (neutral) or p (park) position. Note: when the ignition is in the on position, the brake pedal must be pressed to move t...

  • Page 180

    Brake transmission shift interlock system (btsi) this vehicle is equipped with a brake transmission shift interlock system (btsi) that holds the gearshift lever in the p (park) position when the ignition switch is in an unlocked position. To move the gear selector lever out of the p (park) position,...

  • Page 181

    Note: even if the transmission can be reset, it is recommend that you see your dealer at your earliest possible convenience. Your dealer has the proper diag- nostic equipment to determine if the problem could recur. If the transmission is cannot be reset, dealer service is required. Gear ranges do n...

  • Page 182

    • when shifting into p (park), depress the button on the shift lever and firmly move the lever all the way forward until it stops. • look at the shift indicator window on the console to ensure it is in the p (park) position. • when engaged in p (park), you will not be able to move the shifter rearwa...

  • Page 183

    • vehicle speed is above approximately 30 mph (48 km/h). • transmission has reached normal operating tempera- ture. When frequent transmission shifting occurs while using overdrive, such as when operating the vehicle under heavy load conditions (for example, in hilly terrain, strong head winds, or t...

  • Page 184

    Reaches the appropriate temperature. Refer to the “note” under “torque converter clutch” later in this section. If the transmission temperature gets too hot, the trans- mission may downshift out of overdrive or engage overdrive at higher vehicle speeds (4.7l engines only) until the transmission cool...

  • Page 185

    Over temperature mode the transmission electronics constantly monitor the transmission oil temperature. If the transmission gets too hot, the transmission will change the way it shifts to help control the condition. This may result in a slightly different feeling or response during normal operation ...

  • Page 186

    Rocking the vehicle if the vehicle becomes stuck in snow, sand, or mud, it can often be moved by a rocking motion. Move the gear selector rhythmically between “first” and r (reverse), while applying slight pressure to the accelerator. The least amount of accelerator pedal pressure to main- tain the ...

  • Page 187

    Mode allows the front and rear wheels to rotate at different speeds which eliminates driveline binding and component wear that is normally associated with driving the vehicle in the 4 part time position on dry hard surfaced roads. This feature provides the safety, security, and convenience of operat...

  • Page 188

    Proper operation of four wheel drive vehicles depends on tires of equal size, type, and circumference on each wheel. Any difference will adversely affect shifting and cause damage to the transfer case. Because four wheel drive provides improved traction, there is a tendency to exceed safe turning an...

  • Page 189

    N (neutral) neutral — disengages both the front and rear driveshafts from the powertrain. To be used for flat towing behind another vehicle. Refer to “recreational towing” in sec- tion 5 of this manual. 4lo part time four wheel drive low range — low speed 4 wheel drive. Locks the transfer case inter...

  • Page 190

    Induce a torque interrupt and allow full engagement of the newly selected position. With the vehicle stationary, it may be necessary to shift from d (drive) to r (reverse) and back to d (drive) after shifting. This will allow full engagement of the newly selected position. Apply a constant force whe...

  • Page 191

    5 km/h). Avoid attempting to engage or disengage 4lo with the vehicle moving faster than 2 to 3 mph (3 to 5 km/h). Quadra-trac ii t operating instructions/precautions — if equipped the quadra-trac ii t transfer case is fully automatic in the normal driving 4 all time mode. The quadra-trac ii t trans...

  • Page 192

    Warning! You or others could be injured if you leave the vehicle unattended with the transfer case in the n (neutral) position without first fully engaging the parking brake. The transfer case n (neutral) position disengages both the front and rear driveshafts from the powertrain and will allow the ...

  • Page 193

    Speed. Additional traction and maximum pulling power for loose, slippery road surfaces only. Do not exceed 25 mph (40 km/h). Shifting procedure 4 all time to 4 lo or 4 lo to 4 all time with the vehicle rolling at 2 to 3 mph (3 to 5 km/h), shift the transmission into n (neutral). While the vehicle is...

  • Page 194

    Quadra-drive t system — if equipped the optional quadra-drive t system features three torque transfer couplings. The couplings include vari- lok front and rear axles and quadra-trac ii t transfer case. The optional vari-lok axles are fully automatic and require no driver input to operate. Under norm...

  • Page 195

    Note: the instrument cluster “brake warning light” indicates only that the parking brake is applied. It does not indicate the degree of brake application. Before leaving the vehicle parked on a hill, you must make sure the parking brake is fully applied and place the gear selector in the p (park) po...

  • Page 196

    Warning! • leaving children unattended in a vehicle is dan- gerous for a number of reasons. A child or others could be injured. Children should be warned not to touch the parking brake or the gear selector lever. Don’t leave the keys in the ignition. A child could operate power windows, other contro...

  • Page 197

    Anti-lock brake system the anti-lock brake system (abs) is designed to aid the driver in maintaining vehicle control under adverse braking conditions. The system operates with a separate computer to modulate hydraulic pressure to prevent wheel lock-up and help avoid skidding on slippery surfaces. Al...

  • Page 198

    Warning! • anti-lock system (abs) cannot prevent the natu- ral laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency be- yond that afforded by the condition of the vehicle brakes and tires or the traction afforded. • the abs cannot prevent accidents, includin...

  • Page 199

    • do not “ride” the brakes by resting your foot on the pedal. This could overheat the brakes and result in unpredictable braking action, longer stopping dis- tances, or brake damage. • when descending mountains or hills, repeated brak- ing can cause brake fade with loss of braking control. Avoid rep...

  • Page 200

    An advantage of the higher ground clearance is a better view of the road, allowing you to anticipate problems. They are not designed for cornering at the same speeds as conventional 2-wheel drive vehicles any more than low- slung sports cars are designed to perform satisfactorily in off-road conditi...

  • Page 201

    To help regulate your speed. If the brakes are required to control vehicle speed, apply them lightly and avoid locking or skidding the tires. Warning! If the engine stalls or you lose headway or cannot make it to the top of a steep hill or grade, never attempt to turn around. To do so may result in ...

  • Page 202

    After driving off-road off-road operation puts more stress on your vehicle than does most on-road driving. After going off-road it is always a good idea to check for damage. That way you can get any problems taken care of right away and have your vehicle ready when you need it. • completely inspect ...

  • Page 203

    Tire safety information tire markings note: • p(passenger)-metric tire sizing is based on u.S. Design standards. P-metric tires have the letter “p” molded into the sidewall preceding the size designation. Ex- ample: p215/65r15 95h. • european metric tire sizing is based on european design standards....

  • Page 204

    Tire sizing chart example: size designation: p = passenger car tire size based on u.S. Design standards (....Blank....( = passenger car tire based on european design standards lt = light truck tire based on u.S. Design standards t = temporary spare tire 31 = overall diameter in inches (in) 215 = sec...

  • Page 205

    Example: service description: 95 = load index —a numerical code associated with the maximum load a tire can carry. H = speed symbol —a symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions. —the maximum speed corresp...

  • Page 206

    Tire identification number (tin) the tin may be found on one or both sides of the tire however the date code may only be on one side. Tires with white sidewalls will have the full tin including date code located on the white sidewall side of the tire. Look for the tin on the outboard side of black s...

  • Page 207

    Tire loading and tire pressure tire placard location note: some vehicles have a “tire and loading infor- mation” placard located on the driver’s side “b” pillar. Tire and loading information placard this placard tells you important information about the, 1) number of people that can be carried in th...

  • Page 208

    Loading the vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size and cold tire inflation pressures specified on the tire and loading informatio...

  • Page 209

    3. Subtract the combined weight of the driver and pas- sengers from xxx kilograms or xxx pounds. 4. The resulting figure equals the available amount of cargo and luggage load capacity. For example, if “xxx” amount equals 1400 lbs. And there will be five 150 lb. Passengers in your vehicle, the amount...

  • Page 210

    210 starting and operating.

  • Page 211

    Warning! Overloading of your tire is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. Tires — general information proper tire inflation pressure is essential ...

  • Page 212

    2. Economy— improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Under inflation also increases tire rolling resistance and results in higher fuel consump- t...

  • Page 213

    The tire pressure should be checked and adjusted at least once every month. Check more often if subject to a wide range of outdoor temperatures, as tire pressures vary with temperature changes. Inflation pressures specified on the label are always “cold inflation pressure.” cold inflation pressure i...

  • Page 214

    Radial-ply tires warning! Combining radial ply tires with other types of tires on your vehicle will cause your vehicle to handle poorly. The instability could cause an accident. Al- ways use radial tires in sets of four. Never combine them with other types of tires. Cuts and punctures in radial tire...

  • Page 215

    Tread wear indicators these indicators are narrow strips 1/16 inch (1.6 mm) thick and are found in the tread pattern grooves. When the tread pattern is worn down to these treadwear indicators, the tires should be replaced. Overloading your vehicle, long trips in very hot weather, and driving on bad ...

  • Page 216

    Warning! • do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change suspen- sion dimensions and performance characteristics, resulting in changes to steering, handling, and brak- ing of your vehicle. This can caus...

  • Page 217

    Alignment and balance the suspension components of your vehicle should be inspected and aligned when needed, to obtain maximum tire tread life. Poor suspension alignment may result in: • reduced tread life; • uneven tire wear, such as feathering and one-sided wear; • vehicle pull to the right or to ...

  • Page 218

    Gauge. There will be a delay between the instant you adjust the air pressure in a tire and when the system updates the display. The tpm system is not intended to provide you with notification of rapid air loss. The following chart indicates the tpm system pressure levels. A threshold is the level at...

  • Page 219

    And display spare swap detected along with a chime. This could take up to 10 minutes with vehicle speed above 25 mph (40 km/h). With the 4 tire tpm system, if a road tire and wheel is replaced by the spare, the tpm system will display tire sensor bad/missing. This is due to the spare tire not being ...

  • Page 220

    Tire chains certain models have sufficient tire-to-body clearance to allow use of tire chains. Install chains on rear tires only. Follow these recommendations to guard against damage and excessive tire and chain wear: • do not install tire chains or traction devices on ve- hicles with larger than p2...

  • Page 221

    Note: the tire pressure monitor system must be retrained following a tire rotation. See your authorized dealer for service. The suggested rotation method is the “forward-cross” shown in the following diagram. Fuel requirements your engine is designed to meet all emis- sions regulations and provide e...

  • Page 222

    Poor quality gasoline can cause problems such as hard starting, stalling and hesitations. If you experience these symptoms, try another brand of gasoline before consid- ering service for the vehicle. Over 40 auto manufacturer’s world wide have issued and endorsed consistent gasoline specifications (...

  • Page 223

    Mmt in gasoline mmt is a manganese containing metallic additive that is blended into some gasoline to increase octane. Gasoline blended with mmt provides no performance advantage beyond gasoline of the same octane number without mmt. Gasoline blended with mmt reduces spark plug life and reduces emis...

  • Page 224

    Caution! If the “malfunction indicator light” is flashing, immediate service is required. See “onboard diag- nostic system” in section 7 of this manual. Materials added to fuel all gasoline sold in the united states is required to contain effective detergent additives. Use of additional detergents o...

  • Page 225

    Caution! Damage to the fuel system or emission control system could result from using an improper fuel tank filler cap (gas cap). A poorly fitting cap could let impurities into the fuel system. Warning! • remove the fuel cap slowly to prevent fuel spray from the filler neck which may cause injury. •...

  • Page 226

    Trailer towing in this section you will find information on limits to the type of towing you can reasonably do with your vehicle. And you will find safety tips. Before towing a trailer carefully review this information to tow your load as efficiently and safely as possible. The factory-installed cla...

  • Page 227

    Warning! Improper towing can lead to an injury accident. Follow these guidelines to make your trailer towing as safe as possible: • be sure a trailer is loaded heavier in front, about 10% to 15% of gross trailer weight. Loads balanced over the wheels or heavier in the rear cause the trailer to sway ...

  • Page 228

    • it is recommended that any hitches installed on your vehicle be factory installed, or installed by a dealer using factory approved parts. Factory approved parts are specifically engineered with your vehicle’s perfor- mance in mind, including the possibility that it will be involved in an accident....

  • Page 229

    Always load a trailer with 60% of the cargo weight in the front of the trailer. This places approximately 10% to 15% of the gtw on the tow hitch of your vehicle. This portion of the gtw becomes the tongue weight. Trailer sway control and equalizing hitch are required for tongue weights above 350 lbs...

  • Page 230

    Minimum vehicle requirements for trailer towing 230 starting and operating.

  • Page 231

    Note: if you tow a trailer frequently, especially in hilly country or when the outdoor temperature is high, we recommend that you change the transmission fluid at 30,000 mile (48 000 km) intervals. Caution! When pulling a heavy load or driving a fully loaded vehicle use a premium unleaded fuel to he...

  • Page 232

    Shifting into neutral (n) use the following procedure to prepare your vehicle for recreational towing. Caution! It is necessary to follow these steps to be certain that the transfer case is fully in n (neutral) before recreational towing to prevent damage to internal parts. 1. Depress brake pedal. 2...

  • Page 233

    Caution! Transmission damage may occur if the transmission is shifted into p (park) with the transfer case in n (neutral) and the engine running. With the transfer case in n (neutral) ensure that the engine is off prior to shifting the transmission into p (park) (refer to steps 7 – 8 above). Shiftin...

  • Page 234

    Caution! • do not use a bumper mounted clamp-on tow bar on your vehicle. The bumper face bar will be damaged. • do not disconnect the rear driveshaft because fluid will leak from the transfer case and damage internal parts. Snow plow snow plows, winches, and other aftermarket equipment should not be...

  • Page 235: Contents

    What to do in emergencies contents m hazard warning flashers . . . . . . . . . . . . . . . . . 236 m if your engine overheats . . . . . . . . . . . . . . . . . 237 m changing a flat tire . . . . . . . . . . . . . . . . . . . . 238 ▫ jack and lug wrench locations . . . . . . . . . . . 238 ▫ spare tir...

  • Page 236

    Hazard warning flashers your vehicle’s hazard warning flasher is an emergency warning system. When you activate it, all front and rear directional signals will flash intermittently. Use it when your vehicle is disabled on or near the road. It warns other drivers to steer clear of you and your vehicl...

  • Page 237

    If your engine overheats in any of the following situations, you can reduce the potential for overheating by taking the appropriate ac- tion. • on the highways — slow down. • in city traffic — while stopped, put transmission in n (neutral), but do not increase engine idle speed. Note: there are step...

  • Page 238

    Changing a flat tire jack and lug wrench locations the three piece tool set, consisting of two snap-together extensions that operate the jack and a wheel wrench that also is used as a crank for the jack, is stored under the right rear seat. The scissor-type jack is located under the left rear seat. ...

  • Page 239

    Warning! • always store the jack, lug wrench and spare, flat or damaged tire securely in the proper place. Never leave them loose in the vehicle where they could become dangerous projectiles during a quick stop or collision. • the jack is designed to use as a tool for changing tires only. The jack s...

  • Page 240

    Seatback or completely removed from the vehicle. It can also be kneeled down upon and used as ground cover to prevent clothing from getting soiled. 3. Remove the nut and tire. To replace the spare tire 1. Place the tire into the rear compartment with the wheel facing upward: a. Replace the hold-down...

  • Page 241

    Warning! Temporary-use spare tires are for emergency use only. With these tires, do not drive more than 50 miles (80 km) or exceed 50 mph (80 km/h). Temporary-use spare tires have a total tread life of 3,000 miles (4 800 km). Be sure to follow the warn- ings which apply to your spare. Failure to do ...

  • Page 242

    Tire changing procedure preparation warning! You can be injured or killed if you try to change a wheel too close to moving traffic. Pull far enough off the road to avoid being hit when operating the jack or changing the wheel. • park on a firm, level surface well off the road to provide ample work s...

  • Page 243

    4. Locate the jack as shown. For the front axle, place it under the axle near the wheel to be changed. For the rear axle, place it under the axle as shown. Front jacking location what to do in emergencies 243 6.

  • Page 244

    5. Raise the vehicle by turning the jack handle clockwise until the tire clears the ground. Warning! Raising the vehicle higher than necessary can make the vehicle less stable and cause an accident. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire...

  • Page 245

    9. Tighten the lug nuts securely in a crisscross pattern. Have an authorized service technician check that the torque is 85-115 ft.Lbs. (115-156 n·m) as soon as possible. 10. Secure the jack, lug wrench, jack handle and tire in the proper locations. Warning! • a loose tire or jack thrown forward in ...

  • Page 246

    • do not let anyone sit in the vehicle when it is on a jack. • do not get under the vehicle when it is on a jack. • only use the jack in the positions indicated. • if working on or near a roadway, be extremely careful of motor traffic. Jump starting procedure note: check the charge indicator on top ...

  • Page 247

    Note: to start the vehicle following connection of a booster battery, the security alarm system must first be disabled by cycling a front door key cylinder or by using the keyless entry transmitter. Warning! Jump starting can be dangerous. To avoid personal injury or damage to electrical components ...

  • Page 248

    Warning! Do not attempt to push or tow your vehicle to get it started. Unburned fuel could enter the catalytic converter and, once the engine has started, ignite and damage the converter and vehicle. Emergency tow hooks — if equipped if your vehicle is equipped with tow hooks, they will be mounted i...

  • Page 249: Maintaining Your Vehicle

    Maintaining your vehicle contents m 4.0l engine . . . . . . . . . . . . . . . . . . . . . . . . . . . 251 m 4.7l/4.7 ho engine . . . . . . . . . . . . . . . . . . . . . 252 m onboard diagnostic system — obd ii . . . . . . . . 253 m emissions inspection and maintenance programs . . . . . . . . . . . ...

  • Page 250

    ▫ driveline and steering component lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . 267 ▫ body lubrication . . . . . . . . . . . . . . . . . . . . . 267 ▫ windshield wiper blades . . . . . . . . . . . . . . . . 268 ▫ windshield washers — front and rear . . . . . 268 ▫ exhaust system ....

  • Page 251

    4.0l engine maintaining your vehicle 251 7.

  • Page 252

    4.7l/4.7 ho engine 252 maintaining your vehicle.

  • Page 253

    Onboard diagnostic system — obd ii your vehicle is equipped with a sophisticated onboard diagnostic system called obd ii. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide ex...

  • Page 254

    Emissions inspection and maintenance programs in some localities, it may be a legal requirement to pass an inspection of your vehicle’s emissions control system. Failure to pass could prevent vehicle registration. For states which have an i/m (inspection and maintenance) requirement, this check veri...

  • Page 255

    Ignition key or start the engine. This means that your vehicle’s obd system is not ready and you should not proceed to the i/m station. B. The mil will not flash at all and will remain fully illuminated until you turn off the ignition key or start the engine. This means that your vehicle’s obd syste...

  • Page 256

    Note: intentional tampering with emissions control systems can result in civil penalties being assessed against you. Warning! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the proper equipment. If you have any doubt abou...

  • Page 257

    The best time to check the engine oil level is about 5 minutes after a fully warmed engine is shut off or before starting the engine after it has sat overnight. Checking the oil while the vehicle is on level ground will improve the accuracy of the oil level readings. Maintain the oil level between t...

  • Page 258

    Caution! Overfilling or underfilling the crankcase will cause aeration or loss of oil pressure. This could damage your engine. Change engine oil road conditions as well as your kind of driving affect the interval at which your oil should be changed. Check the following to determine if any apply to y...

  • Page 259

    Engine oil selection for best performance and maximum protection for all engines under all types of operating conditions, the manufacturer recommends engine oils that are api cer- tified and meet the requirements of daimlerchrysler material standard ms-6395. American petroleum institute (api) engine...

  • Page 260

    Materials added to engine oils the manufacturer strongly recommends against the ad- dition of any additives (other than leak detection dyes) to engine oil. Engine oil is an engineered product and it’s performance may be impaired by supplemental addi- tives. Disposing of used engine oil care should b...

  • Page 261

    Drive belts - check condition and tension at the mileages shown in the appropriate “maintenance schedule,” check all drive belts for condition and proper tension. Improper belt tension can cause belt slippage and failure. Inspect the drive belt for evidence of cuts, cracks, or glazing and replace th...

  • Page 262

    Caution! Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition. In the event of engine malfunction, particularly involv- ing engine misfire or other apparent loss of perfor- mance, have your vehicle serviced promptly. Contin- ued operation of your veh...

  • Page 263

    To minimize the possibility of catalytic converter dam- age: • do not shut off the engine or interrupt the ignition when the transmission is in gear and the vehicle is in motion. • do not try to start the engine by pushing or towing the vehicle. • do not idle the engine with any spark plug wires dis...

  • Page 264

    Air cleaner filter under normal driving conditions, replace the air filter at the intervals shown on “maintenance schedule a.” if, however, you drive the vehicle frequently under dusty or severe conditions, the filter element should be inspected periodically and replaced if necessary at the interval...

  • Page 265

    To determine the battery charge, check the battery test indicator (if equipped) on top of the battery. Refer to the illustration. Caution! It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negat...

  • Page 266

    Warning! • use only refrigerants and compressor lubricants approved by the manufacturer for your air condi- tioning system. Some unapproved refrigerants are flammable and can explode, injuring you. Other unapproved refrigerants or lubricants can cause the system to fail, requiring costly repairs. • ...

  • Page 267

    Apparent, and/or the system is not functioning as antici- pated. Coordinate inspection efforts through a certified “daimlerchrysler dealership.” warning! Fluid level should be checked on a level surface with the engine off to prevent injury from moving parts, and to insure accurate fluid level readi...

  • Page 268

    Attention should also be given to hood latching compo- nents to insure proper function. When performing other underhood services, the hood latch, release mechanism and safety catch should be cleaned and lubricated. The external lock cylinders should be lubricated twice a year, preferably in the fall...

  • Page 269

    Warning! Commercially available windshield washer solvents are flammable. They could ignite and burn you. Care must be exercised when filling or working around the washer solution. Exhaust system the best protection against carbon monoxide entry into the vehicle body is a properly maintained engine ...

  • Page 270

    Dirty or rusty in appearance, the system should be drained, flushed and refilled with fresh coolant. Check the front of the radiator for any accumulation of bugs, leaves, etc. Clean the radiator by gently spraying water from a garden hose at the back of the core. Check the engine cooling system hose...

  • Page 271

    Caution! • mixing of coolants other than the specified hoat coolant may result in decreased corrosion protec- tion and engine damage that may not be covered under the new vehicle warranty. If a non-hoat coolant is introduced into the cooling system in an emergency, it should be replaced with the spe...

  • Page 272

    Cooling system pressure cap the cap must be fully tightened to prevent loss of coolant, and to insure that coolant will return to the radiator from the coolant reserve tank. The cap should be inspected and cleaned if there is any accumulation of foreign material on the sealing surfaces. Warning! The...

  • Page 273

    See your authorized dealer if the coolant level drops quickly. Points to remember note: when the vehicle is stopped after a few miles of operation, you may observe vapor coming from the front of the engine compartment. This is normally a result of moisture from rain, snow, or high humidity accumulat...

  • Page 274

    Hoses and vacuum/vapor harnesses inspect surfaces of hoses and nylon tubing for evidence of heat and mechanical damage. Hard or soft spots, brittle rubber, cracking, tears, cuts, abrasions, and exces- sive swelling indicate deterioration of the rubber. Pay particular attention to the hoses nearest t...

  • Page 275

    Cuts, abrasion, and excessive swelling suggest deteriora- tion of the rubber. Particular attention should be made to examining those hose surfaces nearest to high heat sources, such as the exhaust manifold. Inspect all hose clamps and couplings to make sure they are secure and no leaks are present. ...

  • Page 276

    Brake master cylinder the fluid level in the master cylinder should be checked when performing under hood services, or immediately if the brake system warning lamp shows system failure be sure to clean the top of the master cylinder area before removing the cap. If necessary, add fluid to bring the ...

  • Page 277

    Warning! Overfilling the brake fluid reservoir can result in spilling brake fluid on hot engine parts and the brake fluid catching fire. Use only brake fluid that has been in a tightly closed container to avoid contamination from foreign matter. Do not allow petroleum base fluid to contaminate the b...

  • Page 278

    The transmission with an improper fluid level will greatly reduce the life of the transmission and of the fluid. To check the automatic transmission fluid level properly, the following procedure must be used: 1. The vehicle must be on level ground. 2. The engine should be running at curb idle speed ...

  • Page 279

    Least 15 miles (25 km) of driving. At normal operating temperature the fluid cannot be held comfortably be- tween the fingertips. To check the automatic transmission fluid level properly, the following procedure must be used: 1. Operate the engine at idle speed and normal operating temperature. 2. T...

  • Page 280

    Caution! Be aware that if the fluid temperature is below 50°f (10°c) it may not register on the dipstick. Do not add fluid until the temperature is elevated enough to produce an accurate reading. 7. Check for leaks. Release parking brake. To prevent dirt and water from entering the transmission afte...

  • Page 281

    Drain first remove fill plug, then remove drain plug. Recom- mended tightening torque for drain and fill plugs is 15–25 ft. Lbs (20–34 n·m). Caution! When installing plugs, do not overtighten. You could damage them and cause them to leak. Selection of lubricant use only manufacturer’s recommended fl...

  • Page 282

    The following maintenance recommendations will enable you to obtain maximum benefit from the corrosion resistance built into your vehicle. What causes corrosion? Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle. The most common causes are: • road...

  • Page 283

    Caution! Do not use abrasive or strong cleaning materials such as steel wool or scouring powder, which will scratch metal and painted surfaces. Special care • if you drive on salted or dusty roads or if you drive near the ocean, hose off the undercarriage at least once a month. • the drain holes in ...

  • Page 284

    Interior care use mopar t fabric cleaner to clean fabric upholstery and carpeting. Use mopar t vinyl cleaner to clean vinyl upholstery. Mopar t vinyl cleaner is specifically recommended for interior vinyl trim. Do not use silicon based cleaning products on leather seats. They could cause cracking of...

  • Page 285

    Warning! Do not use volatile solvents for cleaning purposes. Many are potentially flammable, and if used in closed areas they may cause respiratory harm. Do not use gasoline, turpentine, kerosene, etc. For cleaning. Use the mopar t recommended products or the equivalents. Carpet vacuum your carpet r...

  • Page 286

    Vegetation or brush that could become a fire hazard, or conceal damage to fuel lines, brake hoses, axle pinion seals, and propeller shafts. Caution! Under frequent heavy-duty driving conditions, change all lubricants and lubricate body compo- nents, all driveline joints and steering linkage more oft...

  • Page 287

    Cavity fuse description 1 spare 2 spare 3 10 amp red headlight high beam left 4 15 amp lt. Blue flasher 5 25 amp natural radio/amplifier 6 15 amp lt. Blue park lights 7 10 amp red interior lights 8 15 amp lt. Blue overhead console, rear wiper, ip lights, rear flip- per glass solenoid 9 20 amp yellow...

  • Page 288

    Cavity fuse description 26 15 amp lt. Blue cigar 27 15 amp lt. Blue rear fog lamps (if equipped) 28 10 amp red body control module, acc/ run 29 10 amp red rear wiper switch, washer motors 30 15 amp lt. Blue radio 31 10 amp red ignition start 32 10 amp red ignition run/start- airbag 33 10 amp red ign...

  • Page 289

    Center identifies each component for ease of replacement, if necessary. “cartridge” fuses and relays can be obtained from your authorized dealer. Vehicle storage if you are leaving your vehicle dormant for more than 21 days you may want to take steps to protect your battery. You may: • remove cartri...

  • Page 290

    Interior lights bulb type underpanel courtesy lights . . . . . . . . . . . . . . . . . 906 instrument cluster (general illumination) . . . . . . . 103 telltale/hazard light . . . . . . . . . . . . . . . . . . . . . . 74 * available only from authorized dealers. Exterior lights bulb type backup light...

  • Page 291

    Fluid capacities u.S. Metric fuel (approximate) 20 gallons 76 liters engine oil with filter 4.0 liter engine (sae 10w-30, api certified engine oil) 6 qts 5.7 liters 4.7, 4.7ho liter engine (sae 5w-30, api certified engine oil) 6 qts 5.7 liters cooling system * 4.0 liter engine (mopar t antifreeze/co...

  • Page 292

    Recommended fluids, lubricants and genuine parts engine component fluid, lubricant, or genuine part engine coolant mopar t antifreeze/coolant 5 year/100,000 mile formula hoat (hybrid or- ganic additive technology) engine oil api certified sae 10w-30 engine oil is recommended for the 4.0l engine. Api...

  • Page 293

    Chassis component fluid, lubricant, or genuine part automatic transmission mopar t atf+4 automatic transmission fluid transfer case selec-trac models - mopar t atf+4 automatic transmission fluid. Quadra-trac models - mopar t transfer case fluid (p/n 05016796) axle differential (front-rear) mopar t s...

  • Page 295: Maintenance Schedules

    Maintenance schedules contents m emission control system maintenance . . . . . . . . 296 m maintenance schedules . . . . . . . . . . . . . . . . . . . 296 ▫ schedule “b” . . . . . . . . . . . . . . . . . . . . . . . . 299 ▫ schedule “a” . . . . . . . . . . . . . . . . . . . . . . . . 310 8 m a i n t...

  • Page 296

    Emission control system maintenance the “scheduled” maintenance services, listed in bold type must be done at the times or mileages specified to assure the continued proper functioning of the emission control system. These, and all other maintenance services included in this manual, should be done t...

  • Page 297

    • taxi, police, or delivery service (commercial service) • off-road or desert driving • if equipped for and operated with e-85 (ethanol) fuel. Note: most vehicles are operated under the conditions listed for schedule “b.” note: if any of these apply to you, change your engine oil every 3,000 miles (...

  • Page 298

    Once a month • check the tire pressure and look for unusual wear or damage. • inspect the battery and clean and tighten the terminals as required. • check the fluid levels of the coolant reservoir, brake master cylinder, and transmission, and add as needed. • check all lights and all other electrica...

  • Page 299

    Schedule “b” follow this schedule if you usually operate your vehicle under one or more of the following conditions. • day or night temperatures are below 32°f (0°c) • stop and go driving • excessive engine idling • driving in dusty conditions • short trips of less than 10 miles (16.2 km) • more tha...

  • Page 300

    Miles 3,000 6,000 9,000 12,000 15,000 (kilometers) (5 000) (10 000) (14 000) (19 000) (24 000) change the engine oil and engine oil filter. X x x x x inspect the engine air cleaner filter, replace if nec- essary. X lubricate the upper knuckle ball stud at steering & suspension ball joints. X x drain...

  • Page 301

    Miles 18,000 21,000 24,000 27,000 30,000 (kilometers) (29 000) (34 000) (38 000) (43 000) (48 000) change the engine oil and engine oil filter. X x x x x inspect the engine air cleaner filter, replace if nec- essary. X inspect the pcv valve, replace if necessary. L x replace the spark plugs. X lubri...

  • Page 302

    Miles 33,000 36,000 39,000 42,000 45,000 (kilometers) (53 000) (58 000) (62 000) (67 000) (72 000) change the engine oil and engine oil filter. X x x x x inspect the engine air cleaner filter, replace if nec- essary. X drain and refill the front and rear axles. X inspect the brake linings. X lubrica...

  • Page 303

    Miles 48,000 51,000 54,000 57,000 60,000 (kilometers) (77 000) (82 000) (86 000) (91 000) (96 000) change the engine oil and engine oil filter. X x x x x inspect the engine air cleaner filter, replace if necessary. X inspect the pcv valve, replace if necessary. L x replace the spark plugs. X lubrica...

  • Page 304

    Miles 63,000 66,000 69,000 72,000 75,000 (kilometers) (101 000) (106 000) (110 000) (115 000) (120 000) change the engine oil and engine oil filter. X x x x x inspect the engine air cleaner filter, replace if nec- essary. X lubricate the upper knuckle ball stud at steering & suspension ball joints. ...

  • Page 305

    Miles 78,000 81,000 84,000 87,000 90,000 (kilometers) (125 000) (130 000) (134 000) (139 000) (144 000) change the engine oil and engine oil filter. X x x x x inspect the engine air cleaner filter, replace if nec- essary. X inspect the pcv valve, replace if necessary. L x replace the spark plugs. X ...

  • Page 306

    Miles 78,000 81,000 84,000 87,000 90,000 (kilometers) (125 000) (130 000) (134 000) (139 000) (144 000) drain and refill the automatic transmission fluid, replace main sump filter, and spin-on cooler return filter (if equipped) (4.7l only). X inspect the drive belt and replace as needed. Not require...

  • Page 307

    Miles 93,000 96,000 99,000 102,000 105,000 (kilometers) (149 000) (154 000) (158 000) (163 000) (168 000) change the engine oil and engine oil filter. X x x x x inspect the engine air cleaner filter, replace if nec- essary. X lubricate the upper knuckle ball stud at steering & suspension ball joints...

  • Page 308

    Miles 108,000 111,000 114,000 117,000 120,000 (kilometers) (173 000) (178 000) (182 000) (187 000) (192 000) change the engine oil and engine oil filter. X x x x x inspect the engine air cleaner filter, replace if nec- essary. X inspect the pcv valve, replace if necessary. L x replace the spark plug...

  • Page 309

    Miles 108,000 111,000 114,000 117,000 120,000 (kilometers) (173 000) (178 000) (182 000) (187 000) (192 000) inspect the drive belt and replace as needed. Not required if belt was previously replaced. X drain and refill the transfer case fluid (selec-trac and quadra-trac models). X inspection and se...

  • Page 310

    Schedule “a” miles 6,000 12,000 18,000 24,000 30,000 (kilometers) (10 000) (19 000) (29 000) (38 000) (48 000) [months] [6] [12] [18] [24] [30] change the engine oil and engine oil filter. X x x x x inspect the engine air cleaner filter, and replace if necessary. X replace the spark plugs. X lubrica...

  • Page 311

    Miles 36,000 42,000 48,000 54, 000 (kilometers) (58 000) (67 000) (77 000) (86 000) [months] [36] [42] [48] [54] change the engine oil and engine oil filter. X x x x inspect the brake linings. X x lubricate the upper knuckle ball stud at steering & sus- pension ball joints. X x clean and lubricate t...

  • Page 312

    Miles 60,000 66,000 72,000 78,000 (kilometers) (96 000) (106 000) (115 000) (125 000) [months] [60] [66] [72] [78] change the engine oil and engine oil filter. X x x x inspect the engine air cleaner filter, and replace if nec- essary. X inspect the pcv valve, replace if necessary. L x replace the sp...

  • Page 313

    Miles 84,000 90,000 96,000 102, 000 (kilometers) (134 000) (144 000) (154 000) (163 000) [months] [84] [90] [96] [102] change the engine oil and engine oil filter. X x x x inspect the engine air cleaner filter, and replace if nec- essary. X inspect the pcv valve, replace if necessary. L x replace th...

  • Page 314

    Miles 84,000 90,000 96,000 102, 000 (kilometers) (134 000) (144 000) (154 000) (163 000) [months] [84] [90] [96] [102] drain and refill the automatic transmission fluid, replace main sump filter, and spin-on cooler return filter (if equipped) (4.7l only). X inspect the transfer case fluid (selec-tra...

  • Page 315

    Miles 108,000 114,000 120,000 (kilometers) (173 000) (182 000) (192 000) [months] [108] [114] [120] change the engine oil and engine oil filter. X x x inspect the engine air cleaner filter, and replace if necessary. X inspect the pcv valve, replace if necessary. L x replace the spark plugs. X lubric...

  • Page 316

    Warning! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the proper equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic. 316 schedule “a” 8 m a i n t e n a n c e s c h e d ...

  • Page 317: Contents

    If you need consumer assistance contents m suggestions for obtaining service for your vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 318 ▫ prepare for the appointment . . . . . . . . . . . . 318 ▫ prepare a list . . . . . . . . . . . . . . . . . . . . . . . . 318 ▫ be reasonable...

  • Page 318

    Suggestions for obtaining service for your vehicle prepare for the appointment if you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty, discuss additional charges with the service manager. ...

  • Page 319

    The manufacturer has empowered its dealers to make warranty and repair decisions that ensure you are not inconvenienced. There is no need for you to wait for a decision from the manufacturer. If a special circumstance occurs that requires information from the manufacturer, we have asked the dealer’s...

  • Page 320

    In mexico contact: av. Prolongacion paseo de la reforma, 1240 sante fe c.P. 05109 mexico, d. F. In mexico (915) 729–1248 or 729–1240 outside mexico (525) 729–1248 or 729–1240 customer assistance for the hearing or speech impaired (tdd/tty) to assist customers who have hearing difficulties, the manuf...

  • Page 321

    The manufacturer will not stand behind any service contract that is not the manufacturer’s service contract. It is not responsible for any service contract other than the manufacturer’s service contract. If you purchased a service contract that is not a manufacturer’s service contract, and you requi...

  • Page 322

    322 if you need consumer assistance.

  • Page 323

    Mopar t parts mopar t fluids, lubricants, parts, and accessories are available from your dealer. They will help you keep your vehicle operating at its best. Reporting safety defects in the 50 united states and washington d.C.: if you believe that your vehicle has a defect which could cause a crash o...

  • Page 324

    Publication order forms to order the following manuals, you may use either the website or the phone numbers listed below. Visa, mas- tercard, american express, and discover orders are ac- cepted. If you prefer mailing your payment, please call for an order form. Note: a street address is required wh...

  • Page 325

    Call toll free at 1–800–890–4038 (u.S.) or 1–800–387–1143 (canada) or visit us on the world wide web at: www.Techauthority.Daimlerchrysler.Com or www.Daimlerchrysler.Ca/manuals if you need consumer assistance 325 9.

  • Page 327: Index

    Index 10

  • Page 328

    Adding washer fluid . . . . . . . . . . . . . . . . . . . . . 171 adjustable pedals . . . . . . . . . . . . . . . . . . . . . . . . 84 air cleaner, engine . . . . . . . . . . . . . . . . . . . . . . 264 air conditioner maintenance . . . . . . . . . . . . . . . 265 air conditioning . . . . . . . . . ...

  • Page 329

    Torque converter . . . . . . . . . . . . . . . . . . . . . . 185 auxiliary electrical outlet . . . . . . . . . . . . . . . . . . 115 auxiliary power outlet . . . . . . . . . . . . . . . . . . . . 115 battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 264 emergency starting . . . ....

  • Page 330

    Cassette tape and player maintenance . . . . . . . . . 162 cassette tape player . . . . . . . . . . . . . . . . . . . 143,147 catalytic converter . . . . . . . . . . . . . . . . . . . . . . 261 caution, exhaust gas . . . . . . . . . . . . . . . . . . . . . . 51 cd changer . . . . . . . . . . . . . ....

  • Page 331

    Temperature gauge . . . . . . . . . . . . . . . . . . . . . 131 crankcase emission control system . . . . . . . . . . 263 cruise control . . . . . . . . . . . . . . . . . . . . . . . . . . 86 cruise light . . . . . . . . . . . . . . . . . . . . . . . . . . . 130 cup holder . . . . . . . . . . . . . ...

  • Page 332

    Coolant temperature gauge . . . . . . . . . . . . . . 131 engine oil pressure gauge . . . . . . . . . . . . . . . 130 freeing vehicle when stuck . . . . . . . . . . . . . . . 186 hazard warning flasher . . . . . . . . . . . . . . . . . 236 jacking . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Page 333

    Filters air cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . 264 engine fuel . . . . . . . . . . . . . . . . . . . . . . . . . . 263 finish care . . . . . . . . . . . . . . . . . . . . . . . . . . . . 282 flashers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 236 hazard warn...

  • Page 334

    Gasoline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 221 gasoline, reformulated . . . . . . . . . . . . . . . . . . . 222 gasoline/oxygenate blends . . . . . . . . . . . . . . . . 222 gauges coolant temperature . . . . . . . . . . . . . . . . . . . . 131 fuel . . . . . . . . . . . . ...

  • Page 335

    Instrument cluster . . . . . . . . . . . . . . . . . . . . . . . 127 instrument panel and controls . . . . . . . . . . . . . . 126 interior appearance care . . . . . . . . . . . . . . . . . . 284 interior fuses . . . . . . . . . . . . . . . . . . . . . . . . . . 286 interior lighting . . . . . . . ....

  • Page 336

    Check gauges . . . . . . . . . . . . . . . . . . . . . . . . 130 cruise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130 daytime running . . . . . . . . . . . . . . . . . . . . . . . 78 dimmer switch, headlight . . . . . . . . . . . . . . 76,79 dome . . . . . . . . . . . . . . . . . ....

  • Page 337

    Lumbar support . . . . . . . . . . . . . . . . . . . . . . . . . 67 maintenance, airbag . . . . . . . . . . . . . . . . . . . . . . 43 maintenance free battery . . . . . . . . . . . . . . . . . . 264 maintenance procedures . . . . . . . . . . . . . . . . . . . 256 maintenance schedule . . . . . . . ...

  • Page 338

    Off-pavement driving . . . . . . . . . . . . . . . . . . . . 285 off-road driving . . . . . . . . . . . . . . . . . . . . . 200,285 oil, engine capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . 291 change interval . . . . . . . . . . . . . . . . . . . . . . . 258 dipstick . . . . . . ...

  • Page 339

    Pressure gauge, oil . . . . . . . . . . . . . . . . . . . . . . 130 programmable electronic features . . . . . . . . . . . . . 95 programming transmitters . . . . . . . . . . . . . . . . . . 22 quadra-trac . . . . . . . . . . . . . . . . . . . . . . . . . . . 191 radial ply tires . . . . . . . . . ....

  • Page 340

    Retractable cargo area cover . . . . . . . . . . . . . . . 118 rocking vehicle when stuck . . . . . . . . . . . . . . . . 186 roof type carrier . . . . . . . . . . . . . . . . . . . . . . . 121 rotation, tires . . . . . . . . . . . . . . . . . . . . . . . 218,220 safety checks inside vehicle . . . ....

  • Page 341

    Sentry key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 sentry key programming . . . . . . . . . . . . . . . . . . . 14 sentry key replacement . . . . . . . . . . . . . . . . . . . 13 service assistance . . . . . . . . . . . . . . . . . . . . . . . 318 service contract . . . . . . . ...

  • Page 342

    Supplemental restraint system - airbag . . . . . . . . 35 system, navigation . . . . . . . . . . . . . . . . . . . . . . 152 tachometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129 tape player . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147 temperature control, automatic ....

  • Page 343

    Wheel nut torque . . . . . . . . . . . . . . . . . . . . . 245 tongue weight/trailer weight . . . . . . . . . . . . . . 228 torque converter clutch . . . . . . . . . . . . . . . . . . 185 tow hooks, emergency . . . . . . . . . . . . . . . . . . . 248 towing . . . . . . . . . . . . . . . . . . . . . ...

  • Page 344

    Vehicle storage . . . . . . . . . . . . . . . . . . . . . . . . . 289 vinyl trim . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 284 voltmeter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129 warning flasher, hazard . . . . . . . . . . . . . . . . . . 236 warning lights (instr...