1. DL manuals
  2. Jeep
  3. Automobile
  4. 2004 Liberty
  5. Owner's Manual

Jeep 2004 Liberty Owner's Manual

Summary of 2004 Liberty

  • Page 1

    Table of contents section page 1 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 things to know before starting your vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 3 understanding the fe...

  • Page 3: Introduction

    Introduction contents m introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 ▫ roll over warning . . . . . . . . . . . . . . . . . . . . . 4 m how to use this manual . . . . . . . . . . . . . . . . . . 6 m warnings and cautions . . . . . . . . . . . . . . . . . . . 7 m vehicle identi...

  • Page 4

    Introduction thank you for selecting a jeep t liberty and welcome to our worldwide family. This is a specialized utility vehicle designed for both on-road and off-road use. It can go places and perform tasks for which conventional two-wheel drive vehicles were not intended. However, on-road ride and...

  • Page 5

    And the narrower track, if this vehicle is out of control it may roll over when some other vehicles may not. Do not attempt sharp turns or abrupt maneuvers or other unsafe driving actions that can cause loss of vehicle control. Failure to operate this vehicle safely may result in an accident, roll o...

  • Page 6

    Note: after you read the manual, it should be stored in the vehicle for convenient reference and remain with the vehicle when sold so that the new owner will be aware of all safety warnings. When it comes to service, remember that the manufac- turer knows your vehicle best, has the factory-trained t...

  • Page 7

    Warnings and cautions this manual contains warnings against operating procedures which could result in an accident or bodily injury. It also contains cautions against procedures which could result in damage to your vehicle. If you do not read this entire manual you may miss important information. Ob...

  • Page 8

    Vehicle modifications / alterations warning! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death. 8 introduction.

  • Page 9: Contents

    Things to know before starting your vehicle contents m a word about your keys . . . . . . . . . . . . . . . . . .12 ▫ ignition key . . . . . . . . . . . . . . . . . . . . . . . . . .12 ▫ key-in-ignition reminder . . . . . . . . . . . . . . . .14 m sentry key immobilizer system — if equipped . .14 ▫ ...

  • Page 10

    ▫ to unlock the doors . . . . . . . . . . . . . . . . . . .23 ▫ to lock the doors . . . . . . . . . . . . . . . . . . . . .24 ▫ to unlatch the swing gate flip-up window . .24 ▫ panic alarm . . . . . . . . . . . . . . . . . . . . . . . . . .25 ▫ to use the panic alarm . . . . . . . . . . . . . . . . ...

  • Page 11

    ▫ driver and front passenger supplemental restraint systems (srs) — airbags . . . . . . . . . .46 ▫ child restraint . . . . . . . . . . . . . . . . . . . . . . . .58 m engine break-in recommendations . . . . . . . . . . .68 m safety tips . . . . . . . . . . . . . . . . . . . . . . . . . . . .68 ▫ ex...

  • Page 12

    A word about your keys the keys for your new vehicle are enclosed in a plastic bag with the key code number on it. If you received your keys without the bag, ask your dealer to give you the number. The key code can also be obtained by the dealer from your vehicle invoice. Ignition key insert the key...

  • Page 13

    To remove the ignition key on models with an automatic transmission, place the gearshift lever in p (park), turn the ignition key to lock and remove the key. To remove the ignition key on models with a manual transmission, depress and hold the key release button, turn the ignition key to lock and re...

  • Page 14

    Key-in-ignition reminder if you open the driver’s door and the key is fully inserted in the ignition switch, a chime will sound to remind you to remove the key. Sentry key immobilizer system — if equipped the sentry key immobilizer system (skis) prevents unauthorized operation of the vehicle by disa...

  • Page 15

    Note: • the sentry key immobilizer system is not compatible with remote starting systems. Use of these systems may result in vehicle starting problems and loss of security protection. • mobil speedpass™, additional sentry keys, or any other transponder equipped components on the same keychain will n...

  • Page 16

    Consists of programming a blank key to the vehicle electronics. A blank key is one which has never been programmed. Note: when having the sentry key system serviced, bring all vehicle keys to the dealer. Customer key programming you can program new keys to the system if you have two valid keys by do...

  • Page 17

    2. This device must accept any interference that may be received, including interference that may cause undes- ired operation. Steering wheel lock — if equipped your vehicle may be equipped with a passive steering wheel lock (manual transmission only). This lock pre- vents steering the vehicle witho...

  • Page 18

    Doors and door locks the vacuum fluorescent (vf) display located in the odometer area displays the word “door” as an indication of a door ajar or door not completely closed. When the vehicle is not moving and the door is ajar or not completely closed, the vf display will show the word “door” and the...

  • Page 19

    If the trip/reset button is pressed while the vf warnings are being displayed, the vf display will revert back to only displaying the odometer/trip odometer mileage. Manual door locks use the manual door lock plunger to lock the doors from inside the vehicle. If the plunger is down when the door is ...

  • Page 20

    Warning! • for personal security, and safety in the event of an accident, lock the vehicle doors as you drive as well as when you park and leave the vehicle. • when leaving the vehicle always remove the key from the ignition lock, and lock your vehicle. Do not leave children unattended in the vehicl...

  • Page 21

    Power door locks — if equipped a door lock switch is on each front door panel. Press this switch to lock or unlock the doors. If the plunger is down when the door is closed, the door will lock. Therefore, make sure the keys are not inside the vehicle before closing the door. If you press the door lo...

  • Page 22

    Child protection locks the rear doors of your vehicle are equipped with child protection locks. If you push up on the lever on the open edge of the door it cannot be opened from the inside of the vehicle. Push the lever down to disengage the child protection locks. Warning! Avoid trapping anyone in ...

  • Page 23

    Remote keyless entry this system allows you to lock or unlock the doors or open the swing gate flip-up window from distances of 23–50 feet (7–15 meters) using a transmitter. You don’t have to point the transmitter at the vehicle to activate the system. Each vehicle comes with two transmitters. To un...

  • Page 24

    2. Continue to hold the 9lock9 button, wait at least 4 but no longer than 10 seconds, then press the “rear release” button. 3. Release both buttons. 4. Repeating steps 1–3 will restore original transmitter operation. To lock the doors press and release the “lock” button once to lock the doors, swing...

  • Page 25

    Note: the transmitter can be programmed to unlatch the flip-up window immediately upon activation of the “rear release” button (without pressing and holding) (within 23–50 feet (7–15 meters) of the vehicle) by per- forming the following procedure: 1. Press and hold the “unlock” button on the transmi...

  • Page 26

    To program additional transmitters note: if vehicle is equipped with the optional elec- tronic vehicle information center (evic) in the overhead console, the transmitters may also be programmed through the evic display. For additional information, refer to “overhead console — if equipped” in section...

  • Page 27

    2. This device must accept any interference that may be received, including interference that may cause undes- ired operation. If your remote keyless entry fails to operate from a normal distance, check for these two conditions: 1. Weak batteries in transmitter. The expected life of batteries is fro...

  • Page 28

    Security alarm system — if equipped this system monitors the vehicle doors, swing gate, swing gate flip-up window, and ignition for unautho- rized operation. When the alarm is activated, the system provides both audible and visual signals. The horn, headlights, and tail lights will sound/flash repea...

  • Page 29

    Note: on vehicles equipped with remote keyless entry (rke), there will not be a door lock cylinder on the front passenger door, rear doors, or rear swing gate. Therefore, you will be unable to disarm the system with a manual unlock of the passenger or rear doors. The security alarm system is designe...

  • Page 30

    To open the swing gate, pull the gate handle to its first detent to open just the flip-up window. Pull the handle to its second detent (all the way) to open both the flip-up window and swing gate. Warning! To avoid injury stand back when opening. Glass will automatically rise. The vacuum fluorescent...

  • Page 31

    Note: if vehicle is equipped with the optional elec- tronic vehicle information center (evic) in the overhead console, all warnings including “door”, “gate”, “glass”, and “lowash” will only be displayed in the evic display (not in the instrument cluster). For addi- tional information, refer to “over...

  • Page 32

    If the trip/reset button is pressed while the vf warnings are being displayed, the vf display will revert back to only displaying the odometer/trip odometer mileage. Note: close swing gate before flip-up window. Caution! Do not press on rear wiper blade when closing swing gate, as damage to the blad...

  • Page 33

    Auto down feature — if equipped the driver’s and passenger’s front window switches have an auto down feature. Press the window switch past the detent, release, and the window will go down auto- matically. To open the window part way, press the window switch part way and release it when you want the ...

  • Page 34

    Wind buffeting wind buffeting can be described as the perception of pressure on the ears or a helicopter type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions. This is a normal occur- rence and ...

  • Page 35

    Buckle up even though you are an excellent driver, even on short trips. Someone on the road may be a poor driver and cause a collision which includes you. This can happen far away from home or on your own street. Research has shown that seat belts save lives, and they can reduce the seriousness of i...

  • Page 36

    Warning! • wearing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body. These are the strongest parts of your body and can take the forces of a collision the best. Wearing your belt in the wrong place could make your injuries in a collision much wo...

  • Page 37

    3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” things to know before starting your vehicle 37 2.

  • Page 38

    Warning! A belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. A belt that is too loose will not protect you as well. In a sudden stop you ...

  • Page 39

    Warning! A lap belt worn too high can increase the risk of injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdo- men. Always wear the lap part of your seat belt as low as possible and keep it snug. A twisted belt cannot do its job as well. In a col...

  • Page 40

    6. To release the belt, push the red button marked press on the buckle. The belt will automatically retract to its stowed position. If necessary, slide the latch plate down the webbing to allow it to retract fully. Warning! A frayed or torn belt could rip apart in a collision and leave you with no p...

  • Page 41

    Warning! Position the shoulder belt height adjusters so that the belt rests across the middle of your shoulder. Failure to adjust the safety belt properly could reduce the effectiveness of the seat belt and increase the risk of injury in a collision. As a guide, if you are shorter than average, you ...

  • Page 42

    When to use the automatic locking mode anytime a child safety seat is installed in a passenger front or outboard rear seating position (if equipped). Children 12 years old and under should be properly restrained in the rear seat whenever possible. How to use the automatic locking mode 1. Buckle the ...

  • Page 43

    Warning! • after a vehicle collision, the driver and front passenger outboard seat belt system must be checked by a qualified technician to verify that the “automatic locking retractor” feature for child seats is still functioning properly. In addition, all seat belts should be checked for proper fu...

  • Page 44

    Enhanced driver seat belt use reminder system (beltalert) if the driver’s seat belt has not been buckled within 60 seconds of starting the vehicle and if the vehicle speed is greater than 5 mph (8 km/h), the enhanced warning system (beltalert) will alert the driver to buckle their seat belt. The dri...

  • Page 45

    The enhanced warning system (beltalert) can be reacti- vated by repeating this procedure. Note: although the enhanced warning system (belta- lert) has been deactivated, the seat belt warning light will continue to illuminate while the driver’s seat belt remains unfastened. Seat belts and pregnant wo...

  • Page 46

    Driver and front passenger supplemental restraint systems (srs) — airbags this vehicle has airbags for both the driver and right front passenger as a supplement to the seat belt restraint systems. The driver’s front airbag is mounted in the steering wheel. The passenger side airbag is mounted in the...

  • Page 47

    This vehicle may also be equipped with window bags to protect the driver, front, and rear passengers sitting next to a window. If the vehicle is equipped with window bags, they are located above the side windows. Their covers are also labeled srs airbag. Note: airbag covers may not be obvious in the...

  • Page 48

    Along with the seat belts, front airbags work with the instrument panel knee bolsters to provide improved protection for the driver and front passenger. Window bags also work with seat belts to improve occupant protection. The seat belts are designed to protect you in many types of collisions. The f...

  • Page 49

    You should read the instructions provided with your child restraint to make sure that you are using it properly. 2. All occupants should use their lap and shoulder belts properly. 3. The driver and front passenger seats should be moved back as far as practical to allow the airbag room to inflate. 4....

  • Page 50

    Airbag system components the airbag system consists of the following: • occupant restraint controller • remote acceleration sensors • airbag warning light • driver airbag • passenger airbag • window bags above side windows (if equipped) • steering wheel and column • instrument panel • interconnectin...

  • Page 51

    Modify the rate of inflation based on the occupant size provided by the occupant classification module. The orc will not detect roll over, or rear impacts. The orc monitors the readiness of the electronic parts of the system whenever the ignition switch is in the start or run positions. These includ...

  • Page 52

    Not be able to properly approximate occupant size. Furthermore, the occupant size may appear to increase or decrease due to objects hanging on the seat, other passengers pushing on the seat, or objects lodged underneath the seat. If there is a rapid change in temperature or humidity, the ocs may not...

  • Page 53

    For almost all sizes of properly seated adults, the passen- ger frontal airbag will be enabled in the event of a collision. For small teenagers and some small adults, depending on size, the airbag may or may not be enabled in the event of a collision. For small teenagers and some small adults, depen...

  • Page 54

    Upper right side of the instrument panel separate and fold out of the way as the bags inflate to their full size. The bags fully inflate in about 50–70 milliseconds. This is about half of the time it takes to blink your eyes. The bags then quickly deflate while helping to restrain the driver and fro...

  • Page 55

    Pressure increase due to applied lap belt tension does not cause a small occupant to be classified as a larger occupant. • the bladder mat and pressure sensor are located beneath the seat cushion foam. The pressure sensor sends a signal to the ocm. • the side impact srs window bags are designed to a...

  • Page 56

    • the nylon airbag material may sometimes cause abra- sions and/or skin reddening to the driver and front passenger as the airbags deploy and unfold. The abrasions are similar to friction rope burns or those you might get sliding along a carpet or gymnasium floor. They are not caused by contact with...

  • Page 57

    Also, the fuel system will shut off immediately upon airbag deployment (gasoline models only). The ignition switch will need to be cycled (i.E. Turn the ignition key from the on position to the lock position) after ap- proximately 5 seconds in order to restart the vehicle. Maintaining your airbag sy...

  • Page 58

    Warning! • you need proper knee impact protection in a collision. Do not mount or locate any aftermarket equipment on or behind the knee bolsters. • it is dangerous to try to repair any part of the airbag system yourself. Be sure to tell anyone who works on your vehicle that it has an airbag system....

  • Page 59

    Warning! In a collision, an unrestrained child, even a tiny baby, can become a missile inside the vehicle. The force required to hold even an infant on your lap can become so great that you could not hold the child, no matter how strong you are. The child and others could be badly injured. Any child...

  • Page 60

    • rearward-facing child seats must never be used in the front seat of a vehicle with a front passenger airbag. An airbag deployment could cause severe injury or death to infants in this position. • children who weigh more than 20 lbs (9 kg) and who are older than one year can ride forward-facing in ...

  • Page 61

    Here are some tips for getting the most out of your child restraint: • before buying any restraint system, make sure that it has a label certifying that it meets all applicable safety standards. The manufacturer recommends that you try a child restraint in the vehicle seats where you will use it bef...

  • Page 62

    • when your child restraint is not in use, secure it in the vehicle with the seat belt or remove it from the vehicle. Do not leave it loose in the vehicle. In a sudden stop or collision, it could strike the occupants or seat backs and cause serious personal injury. Latch — child seat anchorage syste...

  • Page 63

    Installing the latch-compatible child restraint system we urge that you carefully follow the directions of the manufacturer when installing your child restraint. Not all child restraint systems will be installed as described here. Again, carefully follow the installation instructions that were provi...

  • Page 64

    In addition, there are tether strap anchorages behind each rear seating position located on the back of the seat. Many, but not all restraint systems will be equipped with separate straps on each side, with each having a hook or connector for attachment to the lower anchorage and a means of adjustin...

  • Page 65

    The seat, removing slack in the straps according to the child restraint manufacturer’s instructions. Warning! Improper installation of a child restraint to the latch anchorages can lead to failure of an infant or child restraint. The child could be badly injured or killed. Follow the manufacturer’s ...

  • Page 66

    If the belt still can’t be tightened, or if by pulling and pushing on the restraint loosens the belt, you may need to do something more. Disconnect the latch plate from the buckle, turn the buckle around, and insert the latch plate into the buckle again. If you still can’t make the child restraint s...

  • Page 67

    Warning! An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchor positions directly behind the child seat to secure a child restraint top tether strap. Children too large for booster seats children who are large enough to wear th...

  • Page 68

    Engine break-in recommendations a long break-in period is not required for the engine in your new vehicle. Drive moderately during the first 300 miles (500 km). After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable. While cruising, brief full-throttle accelerat...

  • Page 69

    • do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas which can kill. Never run the engine in a closed area, such as a garage, and never sit in a parked vehicle with the engine running for a extended period. If the vehicle is stopped in an open area with engine ru...

  • Page 70

    Defrosters check operation by selecting the defrost mode and place the blower control on high speed. You should feel the air directed against the windshield. Safety checks you should make outside the vehicle tires examine tires for excessive tread wear or uneven wear patterns. Check for stones, nail...

  • Page 71: Contents

    Understanding the features of your vehicle contents m mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75 ▫ inside day/night mirror . . . . . . . . . . . . . . . . .75 ▫ inside automatic dimming mirror if equipped . . . . . . . . . . . . . . . . . . . . . . . . . .76 ▫ outside mi...

  • Page 72

    ▫ head restraints . . . . . . . . . . . . . . . . . . . . . . .92 ▫ power seat adjuster — if equipped . . . . . . . . .93 ▫ 65/35 split folding rear seat . . . . . . . . . . . . . .94 ▫ heated seats — if equipped . . . . . . . . . . . . . .97 m to open and close the hood . . . . . . . . . . . . . .9...

  • Page 73

    M electronic speed control . . . . . . . . . . . . . . . . . . 108 ▫ to activate . . . . . . . . . . . . . . . . . . . . . . . . . . 108 ▫ to set at a desired speed . . . . . . . . . . . . . . . 109 ▫ to deactivate . . . . . . . . . . . . . . . . . . . . . . . . 109 ▫ to resume speed . . . . . . . ....

  • Page 74

    ▫ smoker’s package — if equipped . . . . . . . . . . 136 m cargo area features . . . . . . . . . . . . . . . . . . . . . 137 ▫ cargo light . . . . . . . . . . . . . . . . . . . . . . . . . 137 ▫ retractable cargo area cover — if equipped . . . . . . . . . . . . . . . . . . . . . . . 137 ▫ cargo tie-...

  • Page 75

    Mirrors inside day/night mirror the mirror should be adjusted to center on the view through the rear window. A two-point pivot system allows for horizontal and vertical adjustment of the mirror. The mirror should be adjusted while set in the day position (toward windshield). Annoying headlight glare...

  • Page 76

    Inside automatic dimming mirror — if equipped this mirror automatically adjusts for annoying headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light in the button will indicate when the dimming feature is activated. Cauti...

  • Page 77

    Warning! Vehicles and other objects seen in the right side convex mirror will look smaller and farther away than they really are. Relying too much on your right side mirror could cause you to collide with another vehicle or other objects. Use your inside mirror when judging the size or distance of a...

  • Page 78

    Heated remote control mirrors — if equipped these mirrors are heated to melt frost or ice. This feature is activated whenever you turn on the rear window defrost. Illuminated vanity mirrors — if equipped an illuminated vanity mirror is on the sun visor. To use the mirror, rotate the sun visor down a...

  • Page 79

    Phone’s audio is transmitted through your vehicle’s stereo system; the system will automatically mute your radio before receiving or sending a call. Uconnect™ allows you to transfer calls between the system and your cellular phone as you enter or exit your vehicle, and enables you to mute the system...

  • Page 80

    Cellular phone has a different profile (i.E. Headset profile), you will not be able to use any uconnect™ features. The uconnect™ system is fully integrated into your vehicle, including your vehicle’s stereo system. All voice prompts as well as the other party’s voice in a conversa- tion will be play...

  • Page 81

    Pin number. You will not need to remember this pin number after the initial registration process. • the uconnect™ system will then prompt you to begin the cellular phone pairing process on your cellular phone. Please see your cellular phone user’s manual for instructions on how to complete this step...

  • Page 82

    Add names to your uconnect™ phonebook • press the “phone” button to begin. • after the 9ready9 prompt, say 9phonebook new en- try 9. • when prompted, say the name of the new entry. • next, enter the number designation (e.G. “home”, “work”, “mobile”, or “pager”). This will allow you to have multiple ...

  • Page 83

    Phonebook edit can be used to add another phone number to a name entry that already exists in the phonebook. For example, the entry john doe may have a mobile and a home number, but you can add john doe’s work number later through phonebook edit. Delete entries in the uconnect™ phonebook • press the...

  • Page 84

    • the uconnect™ system will play the names of all the phonebook entries. • to call one of the names in the list, press the ’voice recognition’ button during the playing of the desired name and say 9call9. • the uconnect™ system will then prompt you as to number designation you wish to call. • the se...

  • Page 85

    Making a second call while current call in progress to make a second call while you are currently in a call, press the ’voice recognition’ button and say 9dial9 or 9call9 followed by the phone number or phonebook entry you wish to call. The first call will be on hold while the second call is in prog...

  • Page 86

    Phone redial • press the ’phone’ button to begin. • after the 9ready9 prompt, say 9redial9. • the uconnect™ system will call the last number that was dialed on your cellular phone. This may not be the last number dialed by your uconnect™ system. Advanced phone connectivity transferring an active cal...

  • Page 87

    If you would like to connect or disconnect the blue- tooth™ connection between a paired cellular phone and the uconnect™ system, follow the instruction described in your cellular phone user’s manual. List paired cellular phone names • press the ’phone’ button to begin. • after the 9ready9 prompt, sa...

  • Page 88

    Pin. This method can also be used in instances where you are pressing a number on your keypad to navigate through a menu structure or to enter a number for a pager. Barge in - overriding prompts the ’voice recognition’ button can be used when you wish to skip part of a prompt and issue your voice re...

  • Page 89

    Low signal, battery strength, and roam notification the uconnect™ system will provide notification to inform you if your cellular phone is in roaming status, has low signal strength, or has a low battery when you are trying to place a phone call. Dialing using the cellular phone keypad you can dial ...

  • Page 90

    Towing assistance if you need towing assistance, say 9dial towing assis- tance 9 or 9call towing assistance9. Please refer to the 24-hour towing assistance coverage details in the daimlerchrysler motors company 24-hour towing as- sistance program guide. Seats front seat (manual) adjustment move the ...

  • Page 91

    Warning! • adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust any seat only while the vehicle is parked. • do not ride with the seatback reclined so ...

  • Page 92

    Head restraints head restraints can reduce the risk of whiplash injury in the event of impact from the rear. Adjustable head restraints should be adjusted so that the upper edge is as high as practical. The head restraints have a locking button that must be pushed inward to lower the head restraint....

  • Page 93

    Power seat adjuster — if equipped warning! Do not ride with the seatback reclined so that the seat belt is no longer resting against your chest. In a collision you could slide under the seat belt and be seriously or even fatally injured. Use the recliner only when the vehicle is parked. 6–way power ...

  • Page 94

    This seat also has a manual recline lever located just to the rear of the power seat switch. Pull up on the lever to recline the seat. 65/35 split folding rear seat to provide additional storage area, each rear seat can be folded flat to allow for extended cargo space and still maintain some rear se...

  • Page 95

    Warning! • it is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • be...

  • Page 96

    Note: when lifting up on the release handle, the seatback will release easier if you do not pull forward on the seatback; only lift up on the release handle until the seatback disengages, then fold the seat forward. When the seatback is folded completely forward, the head restraints should be flush ...

  • Page 97

    Heated seats — if equipped the heated seat switch is located on the outboard side of the front seats. Pressing this switch to its desired setting (hi or lo) will activate the respective heating element for the heated seat. Once the heated seat switch is activated, depressing it a second time will de...

  • Page 98

    Then, reach under the hood and slide the safety latch to the right and lift the hood. To prevent possible damage, do not slam the hood to close it. Lower the hood until it is open approximately 12 inches (30 cm) and then push hood closed. This should secure both latches. Never drive your vehicle unl...

  • Page 99

    The overhead lights will automatically turn off in about 8 minutes if a door is left open or the dimmer control is left in the dome light position. Turn the ignition switch on to restore the overhead light operation. Rear cargo light the rear cargo light includes an independent “on/off” switch, whic...

  • Page 100

    Front map/reading lights these lights are mounted in the overhead console. Each light can be turned on by pressing the recessed area of the lens. To turn these lights off, press the recessed area of the lens a second time. Multi-function control lever the multi-function control lever controls the op...

  • Page 101

    Parking lights, instrument panel lights, and headlights turn the end cap of the multi-function control lever to the first detent for parking lights and instrument panel lights. Turn to the second detent for headlight operation. To change the brightness of the instrument panel lights, rotate the cent...

  • Page 102

    Note: a tone will chime if the turn signals are left on for more than 2 miles (3.2 km). Lights-on reminder a chime will sound if the driver’s door is left open, and the headlights or parking lights are left on. Battery saver feature — exterior lights if the park lights, headlights, fog lights, or hi...

  • Page 103

    Light bar — if equipped 1. Remove lamp covers by pressing the thumb tab up- wards, and pulling the cover off. Caution! The auxiliary lights mounted on the off road light bar should be illuminated during (off-road use only. ( having them illuminated on public streets, highways, roads, etc. May be ill...

  • Page 104

    2. With the ignition in the on position, press the button to turn on the light bar (located on the instrument panel to the left of the steering column). Press the button again to turn off the light bar. An indicator light in the instrument cluster will illumi- nate when the light bar has been activa...

  • Page 105

    Windshield washers to use the washer, pull the lever toward you and hold while spray is desired. If the lever is pulled while in the delay range, the wiper will operate for two wipe cycles after the lever is released, and then resume the intermit- tent interval previously selected. Note: if vehicle ...

  • Page 106

    Complete display cycle). After this, the display will continue to sequence. After fifteen “lowash” se- quences, the vf display will no longer provide this warning. If the trip/reset button is pressed while the vf warnings are being displayed, the vf display will revert back to only displaying the od...

  • Page 107

    Intermittent wiper system use the intermittent wiper when weather conditions make a single wiping cycle, with a variable pause be- tween cycles, desirable. Move the control lever to any of the first five wiper switch positions by turning the end cap of the control lever. The delay can be regulated f...

  • Page 108

    Warning! Tilting the steering column while the vehicle is moving is dangerous. Without a stable steering col- umn, you could lose control of the vehicle and have an accident. Adjust the column only while the ve- hicle is stopped. Be sure it is locked before driving. Electronic speed control when eng...

  • Page 109

    To set at a desired speed when the vehicle has reached the desired speed, press and release the set button. Release the accelerator and the vehicle will operate at the selected speed. To deactivate a soft tap on the brake pedal, normal braking, or pressing the cancel button will deactivate the speed...

  • Page 110

    Note: when driving uphill, at elevations above 2,000 ft. (610 meters), or when the vehicle is heavily loaded (especially when towing) the vehicle may slow below the set speed. (if the vehicle speed drops below 30 mph (48 km/h), the speed control will automatically disengage). If this happens, you ca...

  • Page 111

    Pressing the menu button will change the displayed programming features. Pressing the step button will select the available choices. Pressing the c/t (compass/ temperature) button will return the display to the normal compass/temperature display. Note: temperature accuracy can be effected from heat ...

  • Page 112

    Note: the dome/reading lights will remain on until the switch is pressed a second time, so be sure they have been turned off before leaving the vehicle. Electronic vehicle information center the electronic vehicle information center (evic), when the appropriate conditions exist, displays the followi...

  • Page 113

    • spare low pressure • spare high pressure • tire pressure unavailable • tire pressure now available • tire sensor bad/missing • spare swap detected tire pressure monitor system the tire pressure monitor (tpm) system uses wireless technology to monitor tire pressure levels. Sensors, mounted to each ...

  • Page 114

    Into the tire pressure display screen and flash the pres- sure value of the tire that is low or high. This will be displayed for the rest of the ignition cycle, or until the c/t, menu, step, or reset button is pressed. Note: this display will return 60 seconds after the c/t, menu, step, or reset but...

  • Page 115

    4. In addition to monitoring the vehicle tires, the tpm system monitors faults within the system. When any fault has been set, the tpm system will display tire sensor bad/missing. Be sure to inspect your tires for proper inflation pressure. After you determine that your tires are properly inflated, ...

  • Page 116

    Display u.S. Or metric? Pressing the step button when in this display selects us or metric. The overhead console and instrument panel displays will be in the selected units. Auto door locks? When this feature is selected, all doors and the swing gate will lock automatically when the speed of the veh...

  • Page 117

    To train additional key fobs (using the evic module) 1. Press the menu button until train remote? No is displayed. Press the step button to change to yes. Then, press a valid fob key will be displayed. Press either the “lock” or “unlock” button on the current key fob. 2. The next display will say pr...

  • Page 118

    Headlamp delay when this feature is selected the driver can choose, when exiting the vehicle, to have the headlamps remain on for 30, 60, or 90 seconds, or not remain on. Pressing the step button when in this display will select 30, 60, 90, or off. Service interval when this feature is selected a se...

  • Page 119

    Note: the tire pressure sensors must be retrained after rotating the tires or replacing one or more sensors. If a wheel rotation is not followed by the retrain procedure, the system will not properly inform you of the correct vehicle location for a low or high pressure tire. The following describes ...

  • Page 120

    7. Repeat step 6 working clockwise around the vehicle (left front, right front, right rear, left rear, spare) until all five tpm sensor positions are trained. 8. Return magnet to storage location. If the display reads training complete, pressing either the step, c/t, reset, or menu buttons will exit...

  • Page 121

    A resettable function is currently being displayed (aver- age economy, trip miles, and time elapsed). A single chime will sound to indicate that a reset has occurred. Global reset if the reset button is pressed twice within 3 seconds while in any of the three resettable displays, the reset button wi...

  • Page 122

    Average miles/gal shows the average fuel economy in miles per gallon (mpg), or liters per 100 km (l/100 km) since the last reset. Miles to empty shows the estimated distance that can be traveled before the fuel gauge shows e (empty). The distance is calcu- lated by multiplying the amount of fuel rem...

  • Page 123

    After completing three 360 degree turns in an area free from large metal or metallic objects, the cal symbol will turn off and the compass will function normally. Manual compass calibration if the compass appears erratic and the cal symbol does not appear, you must manually put the compass into the ...

  • Page 124

    To set the variance: turn the ignition on and set the display to “compass/temperature.” press and hold the reset button five seconds (no more than 10 seconds). The last variance zone number will be displayed. Press the step button to select the new variance zone and press the reset button to resume ...

  • Page 125

    Caution! Changes or modifications not expressively approved by the party responsible for compliance could void the user’s authority to operate this equipment. Garage door opener — if equipped equipped in vehicles that have the optional electronic vehicle information center (evic) the homelink t wire...

  • Page 126

    Retain the original transmitter of the rf device you are programming for use in other vehicles as well as for future homelink programming. It is also suggested that upon the sale of the vehicle, the programmed homelink buttons be erased for security purposes. To erase the programmed buttons, perform...

  • Page 127

    Warning! Your motorized door or gate will open and close while you are programming homelink. Do not program homelink if people or pets are in the path of the door or gate. A moving door or gate can cause serious injury or death to people and pets or damage to objects. 1. Position the end of your han...

  • Page 128

    Note: if the homelink display does not change to trained, contact homelink at www.Homelink.Com or call 1-800-355-3515 for assistance. 4. Press and hold the just-trained homelink button. Transmit should appear on the display. If your device activates when the homelink button is depressed and released...

  • Page 129

    Homelink should now activate your rolling code equipped device. Note: to program the remaining two homelink but- tons, simply repeat the 9programming homelink9 pro- cess. If, after programming the homelink wireless control system, the hand-held transmitter and/or other homelink units in other vehicl...

  • Page 130

    Proceed with the remaining steps under 9programming homelink 9 to complete. Using homelink to operate, simply press and release the programmed homelink button. Activation will now occur for the trained device (i.E. Garage door opener, gate operator, security system, entry door lock, home/office ligh...

  • Page 131

    Press and hold the “v” button in the center of the sunroof switch to open the vent. The sunroof can be stopped at any position between closed and full vent. To close the sunroof from the vent position, press and hold the switch forward. Releasing the switch will stop the movement of the sunroof and ...

  • Page 132

    Express open feature during the express open operation, any movement of the switch will stop the sunroof and it will remain in a partial open position. Again, momentarily pressing the switch rearward will activate the express open feature. To close the sunroof, hold the switch in the forward positio...

  • Page 133

    Power outlet to the right of the convenience tray (lower center of instrument panel) is an outlet for electrically powered accessories. Pull lightly on the top of the plastic cover to open the outlet. There is a rear power outlet located in the right rear cargo area above the storage cargo net/cd ch...

  • Page 134

    The rear power outlet is a direct feed from the battery so it receives power whether the ignition is in the on or off position. All accessories connected to this outlet should be re- moved or turned off when the vehicle is not in use. Caution! Electrical outlet use with engine off • many accessories...

  • Page 135

    Cigar lighter — if equipped the lighter is a direct feed from the battery so it receives power whether the ignition is in the on or off position. It heats when pushed in and pops out automatically when ready for use. To preserve the heating element, do not hold the lighter element in the heating pos...

  • Page 136

    Cup holders in the center console there are two cup holders for the front seat passengers. Note: the front cup holder insert is removable from the console, for cleaning. Smoker’s package — if equipped with the optional smoker’s package, a removable ash tray is inserted into the front cup holder loca...

  • Page 137

    Cargo area features cargo light the cargo area light is activated by opening the swing gate, opening any door, or by rotating the dimmer control on the multi-function control lever to the extreme top position. If all doors are closed and only the swing gate is open, pushing on the cargo light lens s...

  • Page 138

    Warning! In an accident a cargo cover loose in the vehicle could cause injury. It could fly around in a sudden stop and strike someone in the vehicle. Do not store the cargo cover on the cargo floor or in the passenger compartment. Remove the cover from the vehicle when taken from its mounting. Do n...

  • Page 139

    Warning! • cargo tie-down hooks are not safe anchors for a child seat tether strap. In a sudden stop or colli- sion a hook could pull loose and allow the child seat to come loose. A child could be badly injured. Use only the anchors provided for child seat tethers. • the weight and position of cargo...

  • Page 140

    Cargo organizer — if equipped this vehicle may be equipped with a cargo organizer that mounts on the floor behind the rear seat. Items may be placed on the flat surface or stored in the three storage compartments. Warning! • to avoid tipping, lock the shelf securely in all positions. • do not drive ...

  • Page 141

    2. Place the rear corners of the cargo organizer into the supports located on the rear trim panel. Press down on the back of the cargo organizer to lock it into place. Warning! Do not load objects over 30 lbs (13.5 kg) in the upper position. Failure to follow this warning could cause the cargo organ...

  • Page 142

    To open storage compartments 1. Pull up on the center opening of the cargo organizer. 2. Lift up on the storage compartment dividers and lock into place. Cargo organizer removal loosen screw, then lift lever from each mount located on the floor of the rear cargo area, and remove the cargo organizer ...

  • Page 143

    Caution! • to avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity of 150 lbs (68 kg) or 65 lbs (29.5 kg) on renegade models. Always distribute heavy loads as evenly as possible and secure the load appropriately. • long loads which extend over the windshield, ...

  • Page 145: Contents

    Understanding your instrument panel contents m instrument panel and interior controls . . . . . . . 149 m instrument cluster . . . . . . . . . . . . . . . . . . . . . . 150 m instrument cluster description . . . . . . . . . . . . . 151 m electronic digital clock . . . . . . . . . . . . . . . . . . 1...

  • Page 146

    ▫ to set the push-button memory . . . . . . . . . . 161 ▫ balance . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162 ▫ fade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162 ▫ bass and treble tone control . . . . . . . . . . . . 162 ▫ am/fm selection . . . . . . . . . . . . . ...

  • Page 147

    M satellite radio — if equipped . . . . . . . . . . . . . . 190 ▫ system activation . . . . . . . . . . . . . . . . . . . . . 190 ▫ electronic serial number/sirius identification number (ens/sid) . . . . . . . . . . . . . . . . . . . . 190 ▫ selecting satellite mode in rbb and rbk radios . . . . . ....

  • Page 148

    ▫ operating tips . . . . . . . . . . . . . . . . . . . . . . . 202 m rear window features . . . . . . . . . . . . . . . . . . . 203 ▫ rear window wiper/washer . . . . . . . . . . . . . 203 ▫ rear window defroster . . . . . . . . . . . . . . . . . 204 148 understanding your instrument panel.

  • Page 149

    Instrument panel and interior controls understanding your instrument panel 149 4.

  • Page 150

    Instrument cluster 150 understanding your instrument panel.

  • Page 151

    Instrument cluster description 1. Tachometer indicates the permissible engine revolutions-per-minute for each gear range. Before reaching the red area, ease up on the accelerator to prevent engine damage. 2. Turn signal indicator light the arrows will flash in unison with the exterior turn signals, ...

  • Page 152

    The vehicle’s handling and stopping ability. Each tire, including the spare, should be checked monthly when cold and set to the recommended inflation pressure as specified on the vehicle placard. 6. 4lo mode indicator light — if equipped this light alerts the driver that the vehicle is in the 4 lo f...

  • Page 153

    Light will come on when the ignition switch is turned to the on position and may stay on for as long as three seconds. If the light comes back on immediately or comes on during driving, it indicates that the anti-lock portion of the brake system is not functioning and that service is required, howev...

  • Page 154

    Towing a trailer. It should not be allowed to exceed the upper limits of the normal operating range. If the pointer rises to the red zone (five chimes will occur), pull over and stop the vehicle. Do not turn the engine off. Idle the vehicle with the air conditioning turned off, until the pointer dro...

  • Page 155

    14. Cruise indicator light this indicator lights when the speed control system is turned on. 15. Oil pressure warning light shows low engine oil pressure. The light will come on and remain on when the ignition switch is turned from the off to the on position, and the light will turn off after the en...

  • Page 156

    Warning! Driving a vehicle with the brake warning light on is dangerous. A significant decrease in braking per- formance or vehicle stability during braking may occur. It will take you longer to stop the vehicle or will make your vehicle harder to control. You could have an accident. Have the vehicl...

  • Page 157

    The system is arming. After the alarm successfully arms, the light will flash at a slower rate to indicate the alarm is set. 21. Fuel gage when the ignition key is in the on position, the pointer will show the level of fuel remaining in the fuel tank. A small arrow indicates the side of the vehicle ...

  • Page 158

    When driving, if the driver seat belt remains unbuckled, the seat belt warning light will flash or remain on continuously. Refer to 9enhanced driver seat belt re- minder system (beltalert™) 9 in the occupant restraints section for more information. 27. Light bar indicator light — if equipped this li...

  • Page 159

    You understand and save you concern about these “ap- parent” malfunctions, you must understand a point or two about the transmission and reception of radio sig- nals. Two types of signals there are two basic types of radio signals... Am or amplitude modulation, in which the transmitted sound causes ...

  • Page 160

    Sales code rbb—am/fm stereo radio with cassette tape player and cd changer capability operating instructions note: power to operate the radio is supplied through the ignition switch. It must be in the on or acc position to operate the radio. Note: when first learning the control functions, the user ...

  • Page 161

    For your convenience, the volume can be turned down, but not up, when the audio system is off and the ignition is on. Seek press and release the seek button to search for the next station in either the am or fm mode. Press the top of the button to seek up and the bottom to seek down. The radio will ...

  • Page 162

    Every time a preset button is used a corresponding button number will be displayed. Balance the balance control adjusts the left-to-right speaker bal- ance. Press the bal button in and it will pop out. Adjust the balance and push the button back in. Fade the fade control provides for balance between...

  • Page 163

    You can turn the tape player on by inserting a cassette or activating the mode button (with a cassette in the radio), but only when the ignition and radio are on. Each time a cassette is inserted the tape player will begin playing on the side of the cassette that is facing up in the player. Music se...

  • Page 164

    Nr (noise reduction) pushing the number 2 pre-set button when a tape is playing deactivates the dolby noise reduction system*. When dolby is on, the nr symbol appears on the display. Each time a tape is inserted the dolby will turn on. * “dolby” noise reduction manufactured under license from dolby ...

  • Page 165

    Random can be cancelled by pressing the button a second time or by ejecting the cd from the changer. Cd diagnostic indicators when driving over a very rough road, the cd player may skip momentarily. Skipping will not damage the disc or the player, and play will resume automatically. As a safeguard a...

  • Page 166

    Radio display messages your radio has been designed to display certain messages when a problem is detected with the cd player. 166 understanding your instrument panel.

  • Page 167

    Sales code rbk—am/ fm stereo radio with cd player and cd changer controls radio operation power/volume control press the on/vol control to turn the radio on. Turn the volume control clockwise to increase the volume. Note: power to operate the radio is supplied through the ignition switch. It must be...

  • Page 168

    The radio will continue to tune until you release the button. The frequency will be displayed and continu- ously updated while the button is pressed. Balance the balance control adjusts the left-to-right speaker bal- ance. Press the bal button in and it will pop out. Adjust the balance and push the ...

  • Page 169

    Both am and fm. This allows a total of 10 am and 10 fm stations to be locked into push-button memory. The stations stored in set 2 memory can be selected by pressing the push-button twice. Every time a preset button is used a corresponding button number will be displayed. Time press the time button ...

  • Page 170

    If you insert a disc with the ignition on and the radio off, the display will show the time of day. If the power is on, the unit will switch from radio to cd mode and begin to play when you insert the disc. The display will show the track number and index time in minutes and seconds. Play will begin...

  • Page 171

    Mode press the mode button repeatedly to select between the cd player, the optional remote cd changer and the satellite radio (if equipped). When satellite radio (if equipped) is selected “sa” will appear in your radio display. A cd or tape may remain in the player while in the satellite mode. Time ...

  • Page 172

    Random play (rnd) press the random button to play the tracks on the selected disc in random order for an interesting change of pace. Random can be cancelled by pressing the button a second time or by ejecting the cd from the changer. Cd diagnostic indicators when driving over a very rough road, the ...

  • Page 173

    Radio display messages your radio has been designed to display certain messages when a problem is detected with the cd player. Understanding your instrument panel 173 4.

  • Page 174

    Sales code rbp—am & fm stereo radio with cassette tape player, cd player, and optional cd/dvd changer controls radio operation power/volume control press the on/vol control to turn the radio on. Turn the volume control to the right to increase the volume. Note: power to operate the radio is supplied...

  • Page 175

    Toggle the pty button to select the following format types: program type radio display adult hits adlt hit classical classicl classic rock cls rock college college country country information inform jazz jazz foreign language language news news nostalgia nostalga oldies oldies personality persnlty p...

  • Page 176

    The radio display will flash “seek” and the selected pty program type when searching for the next pty station. If no station is found with the selected pty program type, the radio will return to the last preset station. If a preset button is activated while in the pty (program type) mode, the pty mo...

  • Page 177

    Fade the fade control provides for balance between the front and rear speakers. Press the fade button in and it will pop out. Adjust the balance and push the button back in. Tone control the tone controls affect the bass and treble frequency bands. Each is controlled by a slider control with a deten...

  • Page 178

    To set the clock, use a ballpoint pen or similar object to press the hour (h) or minute (m) buttons on the radio, the time setting will increase each time you press the button. Press any other button to exit from the clock setting mode. General information this radio complies with part 15 of fcc rul...

  • Page 179

    Seek press the seek button up for the next selection on the tape and down to return to the beginning of the current selection. Press the seek button up or down to move the track number to skip forward or backward 1 to 7 selections. Press the seek button once to move 1 selection, twice to move 2 sele...

  • Page 180

    The tape from any damage. When power is restored to the tape player, the pinch roller will automatically reengage and the tape will resume play. Dolby noise reduction the dolby noise reduction system* is on when- ever the tape player is on, but may be switched on/off. To turn the dolby noise reducti...

  • Page 181

    Seek press the top of the seek button for the next selection on the cd. Press the bottom of the button to return to the beginning of the current selection, or return to the beginning of the previous selection if the cd is within the first second of the current selection. Scan press the scan button t...

  • Page 182

    To select satellite radio (if equipped), press the mode button until the word sirius™ appears. The following will be displayed in this order: after three seconds, the current channel name and number will be displayed for five seconds. The current program type and channel number will then be displaye...

  • Page 183

    Disc down/program button 5 press the disc (button 5) button to play the previous disc. Seek press the top of the seek button for the next selection on the cd. Press the bottom of the button to return to the beginning of the current selection, or return to the beginning of the previous selection if t...

  • Page 184

    Radio operation power/volume control press the pwr/vol control to turn the radio on. Turn the volume control clockwise to increase the volume. Note: power to operate the radio is controlled by the ignition switch. It must be in the on or acc position to operate the radio. Mode press the mode button ...

  • Page 185

    Balance — bal the balance control adjusts the left-to-right speaker bal- ance. Press the bal button in and it will pop out. Adjust the balance and push the button back in. Fade the fade control provides for balance between the front and rear speakers. Press the fade button in and it will pop out. Ad...

  • Page 186

    General information this radio complies with part 15 of fcc rules and with rss-210 of industry canada. Operation is subject to the following conditions: 1. This device may not cause harmful interference, 2. This device must accept any interference received, including interference that may cause unde...

  • Page 187

    Show the disc number, the track number, and index time in minutes and seconds. Play will begin at the start of track 1. Load/ ejt — load press the load/ ejt button and the button with the corresponding number where the cd is being loaded. After the radio displays “load” insert the cd into the player...

  • Page 188

    Ff/tune/rw press ff (fast forward) and the cd player will begin to fast forward until ff is released. The rw ( reverse) button works in a similar manner. Random play — set / rnd press the rnd button while the cd is playing to activate random play. This feature plays the tracks on the disc in random ...

  • Page 189

    Program type radio display information inform jazz jazz foreign language language news news nostalgia nostalga oldies oldies personality persnlty public public rhythm and blues r & b religious music rel musc religious talk rel talk rock rock soft soft soft rock soft rck soft rhythm and blues soft r&...

  • Page 190

    By pressing the scan button when the pty icon is displayed, the radio will stop at every pty station on the band and list each corresponding program type in the radio display. Time press the time button to change the display from elapsed cd playing time to time of day. Satellite radio — if equipped ...

  • Page 191

    Esn/sid access with rbb and rbk radios with the ignition switch in the accessory position and the radio off, press the tape eject or cd eject (depend- ing on the radio type) and time buttons simultaneously for 3 seconds. The first four digits of the twelve-digit esn/sid number will be displayed. Pre...

  • Page 192

    • the current channel number will then be displayed until an action occurs. A cd or tape may remain in the radio while in the satellite radio mode. Selecting a channel press and release the seek or tune buttons to search for the next channel. Press the top of the button to search up and the bottom o...

  • Page 193

    Pty button ( scan ( when the desired program type is obtained, press the 9scan9 button within five seconds. The radio will play 7 seconds of the selected channel before moving to the next channel of the selected program type. Press the 9scan9 button a second time to stop the search. Note: pressing t...

  • Page 194

    • driving under wide bridges or along tall buildings can cause intermittent reception. • placing objects over or too close to the antenna can cause signal blockage. Remote sound system controls — if equipped the remote sound system controls are located on the rear surface of the steering wheel. Reac...

  • Page 195

    Pressing the center button will make the radio switch between the various modes available (am/fm/tape/ cd, etc.). The left hand control is a rocker type switch with a push-button in the center. The function of the left hand control is different depending on which mode you are in. The following descr...

  • Page 196

    If you press the switch up or down twice it plays the second track, three times, it will play the third, etc. The button in the center of the left hand switch has no function in this mode. Cd player — 6 disc in cargo area pressing the top of the switch once will go to the next track on the cd. Press...

  • Page 197

    Maintain your cassette tape player. The head and capstan shaft in the cassette player can pick up dirt or tape deposits each time a cassette is played. The result of deposits on the capstan shaft may cause the tape to wrap around and become lodged in the tape transport. The other adverse condition i...

  • Page 198

    Radio operation and cellular phones under certain conditions, the cellular phone being on in your vehicle can cause erratic or noisy performance from your radio. This condition may be lessened or eliminated by relocating the cellular phone antenna. This condition is not harmful to the radio. If your...

  • Page 199

    Temperature control the degree of comfort can be selected by rotating the temperature control knob on the right. The coldest tem- perature setting is fully counterclockwise and the warm- est setting fully clockwise. The knob can be positioned at any detent. Mode selection the mode selector (the cent...

  • Page 200

    Mix air flows through the floor outlets, the outlets at the base of the windshield, and the side window demisters outlets. Defrost air flows through the outlets at the base of the windshield and through the side window demister outlets. Air conditioning blower control the rotary knob on the left con...

  • Page 201

    Temperature control the degree of comfort can be selected by rotating the temperature control knob on the right. The coldest tem- perature setting is fully counterclockwise and the warm- est setting fully clockwise. The knob can be positioned at any detent. Mode selection the mode selector (the cent...

  • Page 202

    Panel air flows through the outlets located in the instru- ment panel. Slight airflow from the defrost outlet, located at the base of the windshield, may be noticed. Floor air flows through the floor outlets located under the instrument panel and through the outlets lo- cated in the rear of the cent...

  • Page 203

    Window fogging in mild but rainy or humid weather, windows will fog on the inside. To rapidly clear the fog off all the windows, select the defrost mode, turn the temperature control knob fully clockwise, and position the blower control to its highest speed. Once the windshield has been cleared, adj...

  • Page 204

    If the rear wiper is operating when the ignition is turned off, the wiper will automatically return to the “park” position. When the vehicle is restarted, the wiper will resume function at whichever position the switch is set at. If the swing gate flip-up window is open or the swing gate is open, co...

  • Page 205

    The defroster will automatically turn off after about ten minutes. For about five more minutes of operation, push the button again. To prevent excessive battery drain, use the defroster only when the engine is operating. The push button also activates the heated exterior mirrors, if so equipped. Cau...

  • Page 207: Starting And Operating

    Starting and operating contents m starting procedures . . . . . . . . . . . . . . . . . . . . . 210 ▫ manual transmission . . . . . . . . . . . . . . . . . . 210 ▫ automatic transmission . . . . . . . . . . . . . . . . 210 ▫ normal starting . . . . . . . . . . . . . . . . . . . . . . 210 ▫ extreme c...

  • Page 208

    ▫ shifting procedure . . . . . . . . . . . . . . . . . . . . 230 m trac-lok™ rear axle — if equipped . . . . . . . . . 231 m parking brake . . . . . . . . . . . . . . . . . . . . . . . . . 232 m anti-lock brake system — if equipped . . . . . . . 234 m on-road driving tips . . . . . . . . . . . . . ....

  • Page 209

    ▫ tire pressure monitor system/4–lo mode — if equipped . . . . . . . . . . . . . . . . . . . . . . . 256 ▫ general information . . . . . . . . . . . . . . . . . . . 256 m tire chains . . . . . . . . . . . . . . . . . . . . . . . . . . . 257 m tire rotation recommendations . . . . . . . . . . . . 258...

  • Page 210

    Starting procedures before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. Warning! Do not leave children or animals inside parked vehicles in hot weather. Interior heat build up may cause serious injury or death. Manual transmission apply...

  • Page 211

    Warning! Never pour fuel or other flammable liquids into the throttle body air inlet opening in an attempt to start the vehicle. This could result in a flash fire causing serious personal injury. Extreme cold weather to insure reliable starting at temperatures below –20°f (–29°c), use of an external...

  • Page 212

    If the engine has been flooded, it may start to run, but not have enough power to continue running when the key is released. If this occurs, continue cranking with the accel- erator pedal pushed all the way to the floor. Release the accelerator pedal and the key once the engine is running smoothly. ...

  • Page 213

    Warning! Remember to disconnect the cord before driving. Damage to the 110-115 volt ac electrical cord could cause electrocution. Use the heater when temperatures below 0°f (-18°c) are expected to last for several days. Transmission shifting 5-speed manual overdrive transmission follow the shift pat...

  • Page 214

    Caution! To drive as safely as possible and to prolong the life of your manual transmission, follow these tips: • before shifting from a forward gear into reverse, or from reverse to a forward gear, stop vehicle com- pletely. Otherwise, accelerated transmission wear may result. • do not operate at s...

  • Page 215

    • the manual transmission may be equipped with a “reverse blocker” to prevent inadvertent shifts from 5th gear to reverse. If you experience difficulty shift- ing into “reverse”, make sure that you are not inad- vertently moving the shift lever toward 5th gear when shifting into “reverse.” recommend...

  • Page 216

    Automatic transmission shifting from d (drive) to p (park) or r (reverse) (or from p or r to d) should be done only after the accelerator pedal is released and the vehicle is stopped. Be sure to keep your foot on the brake when moving the shift lever between these gears. Warning! It is dangerous to ...

  • Page 217

    Gear ranges p (park) supplements the parking brake by locking the transmis- sion. The engine can be started in this range. Never use p (park) while the vehicle is in motion. Apply the parking brake when leaving the vehicle in this range. Always apply the parking brake first, and then place the selec...

  • Page 218

    • when shifting into p (park), depress the button on the shift lever and firmly move the lever all the way forward until it stops. • look at the shift indicator window on the console to ensure it is in the p (park) position. • when engaged in p (park), you will not be able to move the shifter rearwa...

  • Page 219

    Overdrive (o/d) for most city and highway driving. The transmission contains an electronically controlled overdrive, and will automatically shift from d (drive) to o/d (overdrive) if the following conditions are present: • the transmission selector is in d (drive). • the o/d off switch has not been ...

  • Page 220

    Note: if the vehicle is started in cold outside tempera- tures, shifts into overdrive may be delayed. Normal overdrive and shifting operation will resume when the temperature of the transmission reaches the appropriate temperature. Refer to the “note” under “torque con- verter clutch” later in this ...

  • Page 221

    Over temperature mode the transmission electronics constantly monitor the transmission oil temperature. If the transmission gets too hot, the transmission will change the way it shifts to help control the condition. This may result in a slightly different feeling or response during normal operation ...

  • Page 222

    Four-wheel drive operation command-trac t operating information/precautions the command-trac t transfer case provides 4 mode positions - 2 (rear) wheel drive high range, 4-wheel drive high range, neutral, and 4-wheel drive low range. This transfer case is intended to be driven in the 2-wheel drive p...

  • Page 223

    Caution! • do not attempt to make a shift while only the front or rear wheels are spinning. The command- trac transfer case is not equipped with a synchro- nizer and therefore the front and rear driveshaft speeds must be equal for the shift to take place. Shifting while only the front or rear wheels...

  • Page 224

    Warning! • because 4-wheel drive provides improved trac- tion, there is a tendency to exceed safe turning and stopping speeds. Do not go faster than road con- ditions permit. • you or others could be injured if you leave the vehicle unattended with the transfer case in the neutral (n) position witho...

  • Page 225

    4l 4-wheel-drive low range - low speed 4 wheel drive. Locks the front and rear driveshafts together. Forces the front and rear wheels to rotate at the same speed. Additional traction and maximum pulling power for loose, slippery road surfaces only. Do not exceed 25 mph (40 km/h). (allows engine star...

  • Page 226

    Note: shifting into or out of 4l is possible with the vehicle completely stopped, however difficulty may oc- cur due to the mating clutch teeth not being properly aligned. Several attempts may be required for clutch teeth alignment and shift completion to occur. The pre- ferred method is with the ve...

  • Page 227

    The part time indicator light, located on the instru- ment cluster, illuminates when the transfer case is shifted to the 4 part time position. The full time indicator light, located on the instru- ment cluster, illuminates when the transfer case is shifted to the 4 full time position. The 4lo mode i...

  • Page 228

    Proper operation of 4-wheel drive vehicles depends on tires of equal size, type, and circumference on each wheel. Any difference will adversely affect shifting and can cause damage to the transfer case. Warning! • because 4-wheel drive provides improved trac- tion, there is a tendency to exceed safe...

  • Page 229

    Shift positions for additional information on the appropriate use of each transfer case mode position see the information below: 2wd rear wheel drive high range - normal street and highway driving. Dry hard surfaced roads. 4 part time part time 4–wheel drive high range - locks the transfer case inte...

  • Page 230

    Shifting procedure 2wd to 4 part time or 4 part time to 2wd shifting between 2wd and 4 part time can be made with the vehicle stopped or in motion. If the vehicle is in motion, shifts can be made up to 55 mph (88 km/h). With the vehicle in motion two momentary releases of the accelerator pedal may b...

  • Page 231

    Rearward into 4lo. In 4 full time, there is a neutral stop to prevent shifting into n (neutral) by accident. Note: pausing in transfer case n (neutral) in vehicles equipped with an automatic transmission may require shutting the engine off to avoid gear clash while completing the shift. If difficult...

  • Page 232

    Warning! On vehicles equipped with a limited-slip differen- tial, never run the engine with one rear wheel off the ground. The vehicle may drive through the rear wheel remaining on the ground and cause you to lose control of your vehicle. Parking brake to set the parking brake, pull the lever up as ...

  • Page 233

    Before leaving the vehicle parked on a hill, you must make sure the parking brake is fully applied and place the gear selector in the p (park) position. Make certain the transfer case is in gear. Failure to do so may cause the vehicle to roll and cause damage or injury. When parking on a hill, it is...

  • Page 234

    Anti-lock brake system — if equipped the anti-lock brake system is designed to aid the driver in maintaining vehicle control under adverse braking conditions. The system operates with a separate com- puter to modulate hydraulic pressure to prevent wheel lock-up and help avoid skidding on slippery su...

  • Page 235

    Warning! Pumping of the anti-lock brakes will diminish their effectiveness and may lead to an accident. Pumping makes the stopping distance longer. Just press firmly on your brake pedal when you need to slow down or stop. Warning! • anti-lock system (abs) cannot prevent the natu- ral laws of physics...

  • Page 236

    Caution! The anti-lock brake system is subject to possible detrimental effects of electronic interference caused by improperly installed aftermarket radios or tele- phones. Note: during severe braking conditions, a pulsing sensation may occur and a clicking noise will be heard. This is normal, indic...

  • Page 237

    In snow, mud and sand in heavy snow, when pulling a load, or for additional control at slower speeds, shift the transmission to a low gear and shift the transfer case to 4l or 4 lo if necessary. Don’t shift to a lower gear than necessary to maintain headway. Over-revving the engine can spin the whee...

  • Page 238

    Remember, never drive diagonally across a hill-always drive straight up or down. If the wheels start to slip as you approach the crest of a hill, ease off the accelerator and maintain headway by turning the front wheels sharply left and right. This will provide fresh “bite” into the surface and will...

  • Page 239

    • after extended operation in mud, sand, water, or similar dirty conditions, have brake rotors, wheels, brake linings, and axle yokes inspected and cleaned as soon as possible. Warning! Abrasive material in any part of the brakes may cause excessive wear or unpredictable braking. You might not have ...

  • Page 240

    • european metric tire sizing is based on european design standards. Tires designed to this standard have the tire size molded into the sidewall beginning with the section width. The letter 9p9 is absent from this tire size designation. Example: 215/65r15 96h • lt(light truck)-metric tire sizing is ...

  • Page 241

    Tire sizing chart example: size designation: p = passenger car tire size based on u.S. Design standards (....Blank....( = passenger car tire based on european design standards lt = light truck tire based on u.S. Design standards t = temporary spare tire 31 = overall diameter in inches (in) 215 = sec...

  • Page 242

    Example: service description: 95 = load index —a numerical code associated with the maximum load a tire can carry. H = speed symbol —a symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions. —the maximum speed corresp...

  • Page 243

    Tire identification number (tin) the tin may be found on one or both sides of the tire however the date code may only be on one side. Tires with white sidewalls will have the full tin including date code located on the white sidewall side of the tire. Look for the tin on the outboard side of black s...

  • Page 244

    Tire loading and tire pressure tire placard location note: some vehicles have a “tire and loading infor- mation” placard located on the driver’s side “b” pillar. Tire and loading information placard this placard tells you important information about the, 1) number of people that can be carried in th...

  • Page 245

    4) the cold tire inflation pressures for the front, rear and spare tires. Loading the vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size and ...

  • Page 246

    3. Subtract the combined weight of the driver and pas- sengers from xxx kilograms or xxx pounds. 4. The resulting figure equals the available amount of cargo and luggage load capacity. For example, if “xxx” amount equals 1400 lbs. And there will be five 150 lb. Passengers in your vehicle, the amount...

  • Page 247

    Starting and operating 247 5.

  • Page 248

    Warning! Overloading of your tire is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. Tires — general information proper tire inflation pressure is essential ...

  • Page 249

    2. Economy— improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Under inflation also increases tire rolling resistance and results in higher fuel consump- t...

  • Page 250

    The tire pressure should be checked and adjusted at least once every month. Check more often if subject to a wide range of outdoor temperatures, as tire pressures vary with temperature changes. Inflation pressures specified on the label are always “cold inflation pressure.” cold inflation pressure i...

  • Page 251

    Radial-ply tires warning! Combining radial ply tires with other types of tires on your vehicle will cause your vehicle to handle poorly. The instability could cause an accident. Al- ways use radial tires in sets of four. Never combine them with other types of tires. Cuts and punctures in radial tire...

  • Page 252

    Tread wear indicators these indicators are narrow strips 1/16 inch (1.6 mm) thick and are found in the tread pattern grooves. When the tread pattern is worn down to these treadwear indicators, the tires should be replaced. Overloading your vehicle, long trips in very hot weather, and driving on bad ...

  • Page 253

    Warning! • do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unap- proved tires and wheels may change suspension dimen- sions and performance characteristics, resulting in changes to steering, handling, and braking of your vehicle. This can caus...

  • Page 254

    Tires may also cause the vehicle to pull left or right. Alignment will not correct this problem. See your dealer for proper diagnosis of the problem. Improper alignment will not normally cause vehicle vibration, which may be a result of tire and wheel out-of-balance. Proper balancing will reduce vib...

  • Page 255

    The following chart indicates the tpm system pressure levels. A threshold is the level at which the tpm system provides you with an indication. High pressure threshold 44 psi (303 kpa ) placard pressure (cold) 33 psi (227 kpa) low pressure threshold 25 psi (172 kpa) note: a tpm system does not repla...

  • Page 256

    Tire pressure monitor system tire/wheel rotation and sensor replacement — if equipped with the tpm system, if a road tire and wheel is replaced by the spare, the tpm system will detect the swap automatically (after the ignition has been cycled) and display spare swap detected along with a chime. Thi...

  • Page 257

    • this device must accept any interference received, including interference that may cause undesired op- eration. The tire pressure sensors are covered under one of the following licenses: united states . . . . . . . . . . . . . . . . . . . . . Kr5s120123 canada . . . . . . . . . . . . . . . . . . ....

  • Page 258

    Tire chains that are recommended for this vehicle are listed below: • mopart p/n 82206828 with p235/70r16 and p235/ 65r17 tires. • mopart p/n 82207074 with p215/75r16 tires. Note: in order to avoid damage to tires, chains, and your vehicle do not drive for a prolonged period of time on dry pavement....

  • Page 259

    Note: the tire pressure monitor system must be retrained following a tire rotation. See your authorized dealer for service. The suggested rotation method is the “forward-cross” shown in the following diagram. Fuel requirements your engine is designed to meet all emis- sions regulations and provide e...

  • Page 260

    Light spark knock at low engine speeds is not harmful to your engine. However, continued heavy spark knock at high speeds can cause damage and immediate service is required. Engine damage resulting from operation with a heavy spark knock may not be covered by the new vehicle warranty. Poor quality g...

  • Page 261

    Caution! Do not use gasoline containing methanol. Gasoline containing methanol may damage critical fuel system components. Mmt in gasoline mmt is a manganese containing metallic additive that is blended into some gasoline to increase octane. Gasoline blended with mmt provides no performance advantag...

  • Page 262

    Caution! If the “malfunction indicator light” is flashing, immediate service is required. See “onboard diag- nostic system” in section 7 of this manual. Materials added to fuel all gasoline sold in the united states is required to contain effective detergent additives. Use of additional detergents o...

  • Page 263

    Caution! Damage to the fuel system or emission control system could result from using an improper fuel tank filler cap (gas cap). A poorly fitting cap could let impurities into the fuel system. Warning! • remove the fuel cap slowly to prevent fuel spray from the filler neck which may cause injury. •...

  • Page 264

    Trailer towing in this section you will find information on limits to the type of towing you can reasonably do with your vehicle. Before towing a trailer, carefully review this information to tow your load as efficiently and safely as possible. To maintain warranty coverage, follow the requirements ...

  • Page 265

    Caution! If the trailer weighs more than 1,000 lbs (454 kg) loaded, it should have its own brakes and they should be of adequate capacity. Failure to do this could lead to accelerated brake lining wear, higher brake pedal effort, and longer stopping distances. Warning! Connecting trailer brakes to y...

  • Page 266

    Minimum vehicle requirements for trailer towing 266 starting and operating.

  • Page 267

    Recreational towing (behind motorhome, etc.) towing – 2wd models recreational towing is not recommended. Provided that the transmission is operable, tow only in n (neutral) at speeds not exceeding 45 mph (72 km/h) and distances less than 100 miles (161 km). If the vehicle is to be towed more than 10...

  • Page 268

    Caution! It is necessary to follow these steps to be certain that the transfer case is fully in n (neutral) before recreational towing to prevent damage to internal parts. 1. Depress brake pedal. 2. Shift transmission into n (neutral). 3. Shift transfer case lever into n (neutral). 4. Start engine. ...

  • Page 269

    Shifting out of neutral (n) use the following procedure to prepare your vehicle for normal usage. 1. Shift transmission into n (neutral). 2. Shift transfer case lever to desired position. 3. Shift automatic transmission into d (drive) or manual transmission into any forward gear. Note: when shifting...

  • Page 270

    Snow plow snow plows, winches, and other aftermarket equipment should not be added to the front end of your vehicle. The airbag crash sensors may be affected by the change in the front end structure. The airbags could deploy unexpect- edly or could fail to deploy during a collision. Warning! Do not ...

  • Page 271: Contents

    What to do in emergencies contents m hazard warning flashers . . . . . . . . . . . . . . . . . 272 m if your engine overheats . . . . . . . . . . . . . . . . . 273 m changing a flat tire . . . . . . . . . . . . . . . . . . . . 274 ▫ jack and lug wrench locations . . . . . . . . . . . 274 ▫ spare tir...

  • Page 272

    Hazard warning flashers your vehicle’s hazard warning flasher is an emergency warning system. When you activate it, all front and rear directional signals will flash intermittently. Use it when your vehicle is disabled on or near the road. It warns other drivers to steer clear of you and your vehicl...

  • Page 273

    If your engine overheats in any of the following situations, you can reduce the potential for overheating by taking the appropriate ac- tion. • on the highways — slow down. • in city traffic — while stopped, put transmission in n (neutral), but do not increase engine idle speed. Note: there are step...

  • Page 274

    Changing a flat tire jack and lug wrench locations the jack, jack handle, and lug wrench are stored beneath the right rear seat. To remove the jack from its stowage position, turn the thumb screw counterclockwise to loosen jack assembly and then remove it. Warning! • always store the jack, lug wrenc...

  • Page 275

    Spare tire location to remove the spare tire from the carrier, remove the tire cover, if equipped, and remove the lug nuts with the lug wrench turning them counterclockwise. Note: if you have added aftermarket accessories to the spare tire mounted carrier, it cannot exceed a gross weight of 50 lbs (...

  • Page 276

    Preparation • park on a firm, level surface well off the road, to provide ample work space. Place automatic transmis- sion in p (park), or manual transmission in r (re- verse), and stop engine. Set parking brake firmly and activate hazard warning flasher. • block tire diagonally oppo- site tire to b...

  • Page 277

    5. Raise the vehicle by turning the jack handle clockwise until the tire clears the ground. Warning! Raising the vehicle higher than necessary can make the vehicle less stable and cause an accident. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire...

  • Page 278

    9. Finish tightening the lug nuts securely in crisscross pattern. Have an authorized service technician check that the torque is 85-110 ft. Lbs. (115-149 n·m) as soon as possible. 10. Remove jack assembly and wheel blocks. 11. Secure jack, lug wrench, jack handle driver, jack extension, and tire in ...

  • Page 279

    • do not let passengers sit in the vehicle when it is on a jack. • do not get under the vehicle when it is on a jack. • failure to follow the “tire changing procedure” may result in personal injury or damage to your vehicle. • only use the jack in the positions indicated. Jump starting procedure not...

  • Page 280

    7. When removing the jumper cables, reverse the above sequence exactly. Be careful of the moving belts and fan. Note: to start the vehicle following connection of a booster battery, the security alarm system must first be disabled by cycling a front door key cylinder or by using the keyless entry tr...

  • Page 281

    Warning! Do not attempt to push or tow your vehicle to get it started. Unburned fuel could enter the catalytic converter and, once the engine has started, ignite and damage the converter and vehicle. Emergency tow hooks — if equipped if your vehicle is equipped with tow hooks, they are mounted in th...

  • Page 283: Maintaining Your Vehicle

    Maintaining your vehicle contents m 2.4l engine . . . . . . . . . . . . . . . . . . . . . . . . . . . 285 m 3.7l engine . . . . . . . . . . . . . . . . . . . . . . . . . . . 286 m onboard diagnostic system — obd ii . . . . . . . . 287 m emissions inspection and maintenance programs . . . . . . . . ....

  • Page 284

    ▫ power steering fluid check . . . . . . . . . . . . . . 300 ▫ driveline and steering component lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . 301 ▫ body lubrication . . . . . . . . . . . . . . . . . . . . . 301 ▫ windshield wiper blades . . . . . . . . . . . . . . . . 301 ▫ windshi...

  • Page 285

    2.4l engine maintaining your vehicle 285 7.

  • Page 286

    3.7l engine 286 maintaining your vehicle.

  • Page 287

    Onboard diagnostic system — obd ii your vehicle is equipped with a sophisticated onboard diagnostic system called obd ii. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide ex...

  • Page 288

    Emissions inspection and maintenance programs in some localities, it may be a legal requirement to pass an inspection of your vehicle’s emissions control system. Failure to pass could prevent vehicle registration. For states which have an i/m (inspection and maintenance) requirement, this check veri...

  • Page 289

    Ignition key or start the engine. This means that your vehicle’s obd system is not ready and you should not proceed to the i/m station. B. The mil will not flash at all and will remain fully illuminated until you turn off the ignition key or start the engine. This means that your vehicle’s obd syste...

  • Page 290

    Note: intentional tampering with emissions control systems can result in civil penalties being assessed against you. Warning! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the proper equipment. If you have any doubt abou...

  • Page 291

    The best time to check the engine oil level is about 5 minutes after a fully warmed engine has been shut off, or before starting the engine after it has sat overnight. Checking the oil while the vehicle is on level ground will improve the accuracy of the oil level readings. Maintain the oil level be...

  • Page 292

    Caution! Overfilling or underfilling the crankcase will cause aeration or loss of oil pressure. This could damage your engine. Change engine oil road conditions as well as your kind of driving affect the interval at which your oil should be changed. Check the following to determine if any apply to y...

  • Page 293

    Engine oil selection for best performance and maximum protection for all engines under all types of operating conditions, the manufacturer recommends engine oils that are api cer- tified and meet the requirements of daimlerchrysler material standard ms-6395. American petroleum institute (api) engine...

  • Page 294

    Materials added to engine oils the manufacturer strongly recommends against the ad- dition of any additives (other than leak detection dyes) to engine oil. Engine oil is an engineered product and it’s performance may be impaired by supplemental addi- tives. Disposing of used engine oil care should b...

  • Page 295

    Special tools are required to properly measure tension and to restore belt tension to factory specifications. Also, check belt routing to make sure there is no interference between the belts and other engine components. Spark plugs spark plugs must fire properly to assure engine perfor- mance and em...

  • Page 296

    Warning! A hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your ex- haust system. Do not park or operate your vehicle in areas where your exhaust system can contact any- thing that can burn. In unusual sit...

  • Page 297

    Engine timing belt — 2.4l engine replace the engine timing belt at the intervals described in the appropriate maintenance schedule. Ignition wiring system — 2.4l engine replace the ignition cables at the intervals described in the appropriate maintenance schedule. Crankcase emission control system p...

  • Page 298

    Maintenance-free battery your vehicle is equipped with a maintenance-free battery. You will never have to add water, nor is periodic main- tenance required. Warning! Battery posts, terminals, and related accessories con- tain lead and lead compounds. Always wash hands after handling the battery. To ...

  • Page 299

    Caution! It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked (+) positive and negative (-) and identified on the battery case. Also, if a “fast charger” is ...

  • Page 300

    Refrigerant recovery and recycling r-134a air conditioning refrigerant is a hydrofluorocar- bon (hfc) that is endorsed by the environmental pro- tection agency and is an ozone-saving product. How- ever, the manufacturer recommends that air conditioning service be performed by dealers or other servic...

  • Page 301

    Driveline and steering component lubrication u-joints (cardan joints) are sealed and do not require lubrication. Prop shafts, yokes, ball joints and other driveline and steering components may be provided with grease fittings for lubrication. Lubrication of these com- ponents at the intervals specif...

  • Page 302

    Remove frost or ice from the windshield. Keep the blade rubber out of contact with petroleum products such as engine oil, gasoline, etc. Windshield washers the fluid reservoir for the windshield washers and the rear window washer is shared. It is located in the front of the engine compartment on the...

  • Page 303

    Or when the underside or rear of the vehicle is damaged; have an authorized technician inspect the complete ex- haust system and adjacent body areas for broken, dam- aged, deteriorated, or mispositioned parts. Open seams or loose connections could permit exhaust fumes to seep into the passenger comp...

  • Page 304

    If the solution is dirty and contains a considerable amount of sediment, clean and flush with reliable cooling system cleaner. Follow with a thorough rinsing to remove all deposits and chemicals. Engine coolant disposal used ethylene glycol based engine coolant is a regulated substance requiring pro...

  • Page 305

    Adding coolant when adding coolant, a minimum solution of 50% rec- ommended ethylene glycol antifreeze coolant in water should be used. Use higher concentrations (not to exceed 70%) if temperatures below -37°f (-38°c) are anticipated. Use only high purity water such as distilled or deionized water w...

  • Page 306

    Coolant level the coolant recovery bottle provides a quick visual method for determining that the coolant level is ad- equate. The coolant level must be at or above the cold full level on the bottle. The radiator normally remains completely full, so there is no need to remove the radiator cap unless...

  • Page 307

    Moisture from rain, snow, or high humidity accumulat- ing on the radiator and being vaporized when the thermostat opens, allowing hot water to enter the radia- tor. If an examination of your engine compartment shows no evidence of radiator or hose leaks, the vehicle may be safely driven. The vapor w...

  • Page 308

    Insure nylon tubing in these areas has not melted or collapsed. Inspect all hose connections such as clamps and couplings to make sure they are secure and no leaks are present. Components should be replaced immedi- ately if there is any evidence of degradation that could cause failure. Brake system ...

  • Page 309

    Inspect all hose clamps and couplings to make sure they are secure and no leaks are present. Note: often fluids such as oil, power steering fluid, and brake fluid are used during assembly plant opera- tions to ease the assembly of hoses to couplings. There- fore, oil wetness at the hose-coupling are...

  • Page 310

    Brake master cylinder the fluid level in the master cylinder should be checked when performing under hood services, or immediately if the “brake warning light” shows system failure. Be sure to clean the top of the master cylinder area before removing the cap. If necessary, add fluid to bring the flu...

  • Page 311

    Warning! Overfilling the brake fluid reservoir can result in spilling brake fluid on hot engine parts and the brake fluid catching fire. Use only brake fluid that has been in a tightly closed container to avoid contamination from foreign matter. Do not allow petroleum base fluid to contaminate the b...

  • Page 312

    To check the automatic transmission fluid level properly, the following procedure must be used: 1. The vehicle must be on level ground. 2. The engine should be running at curb idle speed for a minimum of 60 seconds. 3. Fully apply parking brake. 4. Apply the brakes and shift the transmission into p ...

  • Page 313

    Hydraulic clutch fluid — manual transmission the clutch hydraulic system is a sealed maintenance free system. In the event of leakage or other malfunction, the system must be replaced. Manual transmission selection of lubricant use only manufacturer’s recommended manual trans- mission fluid, refer t...

  • Page 314

    The fluid level should be to the bottom edge of the fill hole (a) when the vehicle is in a level position. Adding fluid only at filler hole until fluid runs out of the hole, when the vehicle is in a level position. Drain first remove fill plug (b), then drain plug (c). Recom- mended tightening torqu...

  • Page 315

    Front/rear axle fluid the front axle has a threaded “fill plug” on the cover plate, and a threaded “drain plug” on the bottom side of the carrier. Fluid level check lubricant should be 1/2 9 (1 cm) below the oil fill hole. Adding fluid add lubricant only at the fill hole and only to the level specif...

  • Page 316

    The most common causes are: • road salt, dirt and moisture accumulation. • stone and gravel impact. • insects, tree sap and tar. • salt in the air near sea-coast localities. • atmospheric fallout/industrial pollutants. Washing • wash your vehicle regularly. Always wash your ve- hicle in the shade us...

  • Page 317

    • if you detect any stone chips or scratches in the paint, touch them up immediately. The cost of such repairs is considered the responsibility of the owner. • if your vehicle is damaged due to an accident or similar cause which destroys the paint and protective coating have your vehicle repaired as...

  • Page 318

    Leather seat care & cleaning leather is best preserved by regular cleaning with a damp soft cloth. Small particles of dirt can act as an abrasive and damage the leather surface and should be removed promptly with a damp cloth. Stubborn soils can be removed easily with a soft cloth and mopar t total ...

  • Page 319

    Seat belt maintenance do not bleach, dye or clean the belts with chemical solvents or abrasive cleaners. This will weaken the fabric. Sun damage will also weaken the fabric. If the belts need cleaning, use a mild soap solution or lukewarm water. Do not remove the belts from the vehicle to wash them....

  • Page 320

    Fuse panel interior fuses the fuse panel is on the left side of the instrument panel. A label is attached to the fuse panel cover to identify each fuse for ease of replacement. 320 maintaining your vehicle.

  • Page 321

    Fuse panel description cavity fuse description 1 15 amp blue horn relay, power sunroof relay, power window relay 2 10 amp red rear fog lights (export only) 3 20 amp yel- low cigar lighter 4 10 amp red headlight low beam right 5 10 amp red headlight low beam left 6 20 amp yel- low body control module...

  • Page 322

    Cavity fuse description 18 20 amp yel- low radio choke & relay 19 20 amp yel- low frt fog lights/trailer tow stop and turn lights 20 spare 21 10 amp red radio 22 20 amp yel- low power sunroof relay/ antenna module (export only) 23 spare 24 10 amp red pdc blower motor 25 10 amp red heated seat switch...

  • Page 323

    Cavity fuse description 37 10 amp red airbag control module 38 10 amp red abs controller/shifter as- sembly 39 10 amp red hazard flasher (turn signals)/backup lamp switch (manual transmission only)/transmission range switch (automatic transmis- sion only) underhood fuses (power distribution center) ...

  • Page 324

    Vehicle storage if you are leaving your vehicle dormant for more than 21 days you may want to take steps to protect your battery. You may: • remove cartridge fuse #15 in the power distribution center labeled ignition-off draw (iod). • store the removed iod fuse in the power distribution center locat...

  • Page 325

    Exterior lights bulb type backup lights . . . . . . . . . . . . . . . . . . . . 3157 p27/7w center high-mounted stoplight . . . . . . . . . 921/w16w fog lights. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9145 front park/turn lights . . . . . . . . . . . . . 3157 p27/7w front side marker...

  • Page 326

    Fluid capacities u.S. Metric fuel (approximate) 19.5 gallons 74 liters engine oil with filter 2.4 & 3.7 liter engine (sae 5w-30, api certified engine oil) 5 qts 4.7 liters cooling system * 2.4 liter engine (mopar t antifreeze/coolant 5 year/100,000 mile formula) 10 qts 9.5 liters 3.7 liter engine (m...

  • Page 327

    Recommended fluids, lubricants and genuine parts engine component fluid, lubricant, or genuine part engine coolant mopar t antifreeze/coolant 5 year/100,000 mile formula hoat (hybrid or- ganic additive technology) engine oil use api certified sae 5w-30 engine oil. Refer to oil viscosity chart for co...

  • Page 328

    Chassis component fluid, lubricant, or genuine part automatic transmission mopar t atf+4 automatic transmission fluid manual transmission mopar t manual transmission lubricant (p/n 04874464) transfer case mopar t atf+4 automatic transmission fluid axle differential (front-rear) mopar t sae 75w-140 (...

  • Page 329: Maintenance Schedules

    Maintenance schedules contents m emission control system maintenance . . . . . . . . 330 m maintenance schedules . . . . . . . . . . . . . . . . . . . 330 ▫ schedule “b” . . . . . . . . . . . . . . . . . . . . . . . . 333 ▫ schedule “a” . . . . . . . . . . . . . . . . . . . . . . . . 342 8 m a i n t...

  • Page 330

    Emission control system maintenance the “scheduled” maintenance services, listed in bold type must be done at the times or mileages specified to assure the continued proper functioning of the emission control system. These, and all other maintenance services included in this manual, should be done t...

  • Page 331

    • off-road or desert driving. Note: most vehicles are operated under the conditions listed for schedule “b.” second is schedule “a”. It is for vehicles that are not operated under any of the conditions listed under sched- ule “b.” use the schedule that best describes your driving condi- tions. Where...

  • Page 332

    At each oil change • change the engine oil filter. • inspect the exhaust system. • inspect brake hoses. • check the coolant level, hoses, and clamps. • inspect manual transmission fluid level — if equipped. • rotate the tires at each oil change interval shown on schedule “a” 6,000 miles (10 000 km) ...

  • Page 333

    Schedule “b” follow schedule “b” if you usually operate your vehicle under one or more of the following conditions. • day or night temperatures are below 32°f (0°c). • stop and go driving. • extensive engine idling. • driving in dusty conditions. • short trips of less than 10 miles (16.2 km). • more...

  • Page 334

    Miles 18,000 21,000 24,000 27,000 30,000 (kilometers) (29 000) (34 000) (38 000) (43 000) (48 000) change the engine oil and engine oil filter. X x x x x inspect the engine air filter element, replace if necessary. X replace the spark plugs. X inspect and replace the pcv valve, if necessary. L x ins...

  • Page 335

    Miles 33,000 36,000 39,000 42,000 45,000 (kilometers) (53 000) (58 000) (62 000) (67 000) (72 000) change the engine oil and engine oil filter. X x x x x inspect the engine air filter element, replace if necessary. X inspect the brake linings. X drain and refill the front and rear axle fluid‡ x insp...

  • Page 336

    Miles 48,000 51,000 54,000 57,000 60,000 (kilometers) (77 000) (82 000) (86 000) (91 000) (96 000) change the engine oil and engine oil filter. X x x x x inspect the engine air filter element, replace if necessary. X replace the spark plugs. X inspect and replace the pcv valve, if necessary. L x rep...

  • Page 337

    Miles 63,000 66,000 69,000 72,000 75,000 (kilometers) (101 000) (106 000) (110 000) (115 000) (120 000) change the engine oil and engine oil filter. X x x x x inspect the engine air filter element, replace if necessary. X inspect the brake linings. X drain and refill the front and rear axle fluid‡ x...

  • Page 338

    Miles 78,000 81,000 84,000 87,000 90,000 (kilometers) (125 000) (130 000) (134 000) (139 000) (144 000) change the engine oil and engine oil filter. X x x x x inspect the engine air filter element, replace if necessary. X replace the spark plugs. X inspect and replace the pcv valve, if necessary. L ...

  • Page 339

    Miles 93,000 96,000 99,000 102,000 105,000 (kilometers) (149 000) (154 000) (158 000) (163 000) (168 000) change the engine oil and engine oil filter. X x x x x inspect the engine air filter element, replace if necessary. X inspect the brake linings. X drain and refill the front and rear axle fluid‡...

  • Page 340

    Miles 108,000 111,000 114,000 117,000 120,000 (kilometers) (173 000) (178 000) (182 000) (187 000) (192 000) change the engine oil and engine oil filter. X x x x x inspect the engine air filter element, replace if necessary. X replace the spark plugs. X inspect and replace the pcv valve, if necessar...

  • Page 341

    Inspection and service should be performed anytime a malfunction is observed or suspected. Retain all receipts. L this maintenance is recommended by the manufac- turer to the owner, but it is not required to maintain emissions warranty. ‡off-highway operation, trailer towing, taxi, limousine, bus, s...

  • Page 342

    Schedule “a” miles 6,000 12,000 18,000 24,000 30,000 (kilometers) (10 000) (19 000) (29 000) (38 000) (48 000) [months] [6] [12] [18] [24] [30] change the engine oil and engine oil filter. X x x x x inspect the engine air filter element, and replace if necessary. X replace the spark plugs. X inspect...

  • Page 343

    Miles 36,000 42,000 48,000 54,000 (kilometers) (58 000) (67 000) (77 000) (86 000) [months] [36] [42] [48] [54] change the engine oil and engine oil filter. X x x x inspect the brake linings. X x schedule “a” 343 8 m a i n t e n a n c e s c h e d u l e s.

  • Page 344

    Miles 60,000 66,000 72,000 78,000 (kilometers) (96 000) (106 000) (115 000) (125 000) [months] [60] [66] [72] [78] change the engine oil and engine oil filter. X x x x inspect the brake linings. X inspect the engine air filter element, and replace if nec- essary. X replace the spark plugs. X inspect...

  • Page 345

    Miles 84,000 90,000 96,000 102,000 (kilometers) (134 000) (144 000) (154 000) (163 000) [months] [84] [90] [96] [102] change the engine oil and engine oil filter. X x x x inspect the brake linings. X inspect the engine air filter element, and replace if nec- essary. X replace the spark plugs. X insp...

  • Page 346

    Miles 108,000 114,000 120,000 (kilometers) (173 000) (182 000) (192 000) [months] [108] [114] [120] change the engine oil and engine oil filter. X x x inspect the brake linings. X inspect the engine air filter element, and replace if necessary. X replace the spark plugs. X inspect and replace the pc...

  • Page 347: Contents

    If you need consumer assistance contents m suggestions for obtaining service for your vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 348 ▫ prepare for the appointment . . . . . . . . . . . . 348 ▫ prepare a list . . . . . . . . . . . . . . . . . . . . . . . . 348 ▫ be reasonable...

  • Page 348

    Suggestions for obtaining service for your vehicle prepare for the appointment if you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty, discuss additional charges with the service manager. ...

  • Page 349

    The manufacturer has empowered its dealers to make warranty and repair decisions that ensure you are not inconvenienced. There is no need for you to wait for a decision from the manufacturer. If a special circumstance occurs that requires information from the manufacturer, we have asked the dealer’s...

  • Page 350

    In mexico contact: av. Prolongacion paseo de la reforma, 1240 sante fe c.P. 05109 mexico, d. F. In mexico (915) 729–1248 or 729–1240 outside mexico (525) 729–1248 or 729–1240 customer assistance for the hearing or speech impaired (tdd/tty) to assist customers who have hearing difficulties, the manuf...

  • Page 351

    The manufacturer will not stand behind any service contract that is not the manufacturer’s service contract. It is not responsible for any service contract other than the manufacturer’s service contract. If you purchased a service contract that is not a manufacturer’s service contract, and you requi...

  • Page 352

    352 if you need consumer assistance.

  • Page 353

    Mopar t parts mopar t fluids, lubricants, parts, and accessories are available from your dealer. They will help you keep your vehicle operating at its best. Reporting safety defects in the 50 united states and washington d.C.: if you believe that your vehicle has a defect which could cause a crash o...

  • Page 354

    Publication order forms to order the following manuals, you may use either the website or the phone numbers listed below. Visa, mas- tercard, american express, and discover orders are ac- cepted. If you prefer mailing your payment, please call for an order form. Note: a street address is required wh...

  • Page 355

    Call toll free at 1–800–890–4038 (u.S.) or 1–800–387–1143 (canada) or visit us on the world wide web at: www.Techauthority.Daimlerchrysler.Com or www.Daimlerchrysler.Ca/manuals if you need consumer assistance 355 9.

  • Page 357: Index

    Index 10

  • Page 358

    Adding washer fluid . . . . . . . . . . . . . . . . . . . . . 204 air cleaner, engine . . . . . . . . . . . . . . . . . . . . . . 297 air conditioner maintenance . . . . . . . . . . . . . . . 299 air conditioning . . . . . . . . . . . . . . . . . . . . . . . . 200 air conditioning controls . . . . ....

  • Page 359

    Auxiliary power outlet . . . . . . . . . . . . . . . . . . . 133 bar, light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103 battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 298 emergency starting . . . . . . . . . . . . . . . . . . . . . 279 keyless transmitter rep...

  • Page 360

    Catalytic converter . . . . . . . . . . . . . . . . . . . . . . 295 caution, exhaust gas . . . . . . . . . . . . . . . . . . . . . . 68 cd changer . . . . . . . . . . . . . . . . . . . . . . 164,171,182 cd player . . . . . . . . . . . . . . . 167,169,174,180,183,186 cd player maintenance . . . . . ....

  • Page 361

    Crankcase emission control system . . . . . . . . . . 297 cruise control . . . . . . . . . . . . . . . . . . . . . . . . . . 108 cruise light . . . . . . . . . . . . . . . . . . . . . . . . . . . 155 cup holder . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136 customer assistance . . . . ....

  • Page 362

    Jump starting . . . . . . . . . . . . . . . . . . . . . . . . . 279 tow hooks . . . . . . . . . . . . . . . . . . . . . . . . . . 281 emission control system maintenance . . . . . . 288,330 engine air cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . 297 block heater . . . . . . . . . . . ...

  • Page 363

    Flashers hazard warning . . . . . . . . . . . . . . . . . . . . . . . 272 turn signal . . . . . . . . . . . . . . . . . . . . . . . . . . 151 flat tire changing . . . . . . . . . . . . . . . . . . . . . . . 274 flooded engine starting . . . . . . . . . . . . . . . . . . . 211 fluid capacities . . . ...

  • Page 364

    Gauges coolant temperature . . . . . . . . . . . . . . . . . . . . 153 fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157 odometer . . . . . . . . . . . . . . . . . . . . . . . . . . . 154 speedometer . . . . . . . . . . . . . . . . . . . . . . . . . 151 tachometer . . . . . . ...

  • Page 365

    Instrument cluster . . . . . . . . . . . . . . . . . . . . . . . 150 instrument panel and controls . . . . . . . . . . . . . . 149 interior appearance care . . . . . . . . . . . . . . . . . . 317 interior fuses . . . . . . . . . . . . . . . . . . . . . . . . . . 320 interior lighting . . . . . . . ....

  • Page 366

    Dome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111 fog . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102 four-wheel drive indicator . . . . . . . . . . . . . . . 152 fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 320 hazard warning flasher . ....

  • Page 367

    Lug nuts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 278 luggage carrier . . . . . . . . . . . . . . . . . . . . . . . . . 142 luggage rack . . . . . . . . . . . . . . . . . . . . . . . . . . 142 maintenance free battery . . . . . . . . . . . . . . . . . . 298 maintenance procedures . ...

  • Page 368

    Odometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154 trip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154 off-pavement driving . . . . . . . . . . . . . . . . . . 236,319 off-road driving . . . . . . . . . . . . . . . . . . . . . . . . 319 oil, engine . . . . . ...

  • Page 369

    Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77 outlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133 seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93 steering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300 sunroof . . . ...

  • Page 370

    Replacement tires . . . . . . . . . . . . . . . . . . . . . . . 252 reporting safety defects . . . . . . . . . . . . . . . . . . . 353 restraint, head . . . . . . . . . . . . . . . . . . . . . . . . . . 92 restraints, child . . . . . . . . . . . . . . . . . . . . . . . . . 58 restraints, infant . . ...

  • Page 371

    Security against theft . . . . . . . . . . . . . . . . . . . 20,28 security alarm . . . . . . . . . . . . . . . . . . . . . . . . . . 28 selection of oil . . . . . . . . . . . . . . . . . . . . . . . . . 293 selec-trac operation . . . . . . . . . . . . . . . . . . . . . . 226 sentry key . . . . . . ...

  • Page 372

    Steering power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300 wheel lock . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 wheel, tilt . . . . . . . . . . . . . . . . . . . . . . . . . . . 107 steering wheel mounted sound system controls . . . . . . . . . . . . . . . . . . . ...

  • Page 373

    Pressure monitor system . . . . . . . . . . . . . . 113,254 radial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 251 replacement . . . . . . . . . . . . . . . . . . . . . . . . . 252 rotation . . . . . . . . . . . . . . . . . . . . . . . . . . 256,258 safety . . . . . . . . . . . . . ....

  • Page 374

    Unleaded gasoline . . . . . . . . . . . . . . . . . . . . . . . 259 upholstery care . . . . . . . . . . . . . . . . . . . . . . . . 317 vacuum/vapor harnesses . . . . . . . . . . . . . . . . . 307 vanity mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . 78 variance, compass . . . . . . ....