1. DL manuals
  2. Jeep
  3. Automobile
  4. 2005 Liberty
  5. Owner's Manual

Jeep 2005 Liberty Owner's Manual

Summary of 2005 Liberty

  • Page 1

    Table of contents section page 1 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 things to know before starting your vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 3 understanding the fea...

  • Page 3: Introduction

    Introduction contents 䡵 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 ▫ roll over warning . . . . . . . . . . . . . . . . . . . . . 5 䡵 how to use this manual . . . . . . . . . . . . . . . . . . 7 䡵 warnings and cautions . . . . . . . . . . . . . . . . . . . 7 䡵 vehicle identi...

  • Page 4

    Introduction thank you for selecting a jeep 威 liberty and welcome to our worldwide family. This is a specialized utility vehicle designed for both on-road and off-road use. It can go places and perform tasks for which conventional two-wheel drive vehicles were not intended. However, on-road ride and...

  • Page 5

    Roll over warning utility vehicles have a significantly higher roll over rate than other types of vehicles. This vehicle has a higher ground clearance, higher center of gravity, and narrower track than many passenger cars. It is capable of perform- ing better in a wide variety of off-road applicatio...

  • Page 6

    Failure to use driver and passenger seat belts provided is a major cause of severe or fatal injury. In fact, the u.S. Government notes that the universal use of existing seat belts could cut the highway death toll by 10,000 or more each year, and could reduce disabling injuries by 2 million annually...

  • Page 7

    Warning! Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the state of california to cause cancer and birth defects or other reproductive harm. In addition, certain fluids contained in vehicles and certain prod- ucts of component wear contai...

  • Page 8

    Vehicle identification number the vehicle identification number (vin) is located on a stamped plate on the bottom of the left front a-pillar, visible from outside of the vehicle through the wind- shield. This number also appears on the automobile information disclosure label affixed to a window on y...

  • Page 9

    Vehicle modifications / alterations warning! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death. Introduction 9 1.

  • Page 11: Contents

    Things to know before starting your vehicle contents 䡵 a word about your keys . . . . . . . . . . . . . . . . . .14 ▫ ignition key . . . . . . . . . . . . . . . . . . . . . . . . . .14 ▫ key-in-ignition reminder . . . . . . . . . . . . . . . .16 䡵 sentry key immobilizer system . . . . . . . . . . . ...

  • Page 12

    ▫ to unlock the doors . . . . . . . . . . . . . . . . . . .25 ▫ to lock the doors . . . . . . . . . . . . . . . . . . . . .26 ▫ to unlatch the swing gate flip-up window . .26 ▫ panic alarm . . . . . . . . . . . . . . . . . . . . . . . . . .27 ▫ to use the panic alarm . . . . . . . . . . . . . . . . ...

  • Page 13

    ▫ driver and front passenger supplemental restraint systems (srs) — airbags . . . . . . . . . .48 ▫ child restraint . . . . . . . . . . . . . . . . . . . . . . . .63 䡵 engine break-in recommendations . . . . . . . . . . .73 䡵 safety tips . . . . . . . . . . . . . . . . . . . . . . . . . . . .73 ▫ ex...

  • Page 14

    A word about your keys the keys for your new vehicle are enclosed in a plastic bag with the key code number on it. If you received your keys without the bag, ask your dealer to give you the number. The key code can also be obtained by the dealer from your vehicle invoice. Ignition key insert the key...

  • Page 15

    To remove the ignition key on models with a manual transmission, depress and hold the key release button, turn the ignition key to lock and remove the key. Warning! Leaving children in a vehicle unattended is danger- ous for a number of reasons. A child or others could be injured. Children should be...

  • Page 16

    Key-in-ignition reminder if you open the driver’s door and the key is fully inserted in the ignition switch, a chime will sound to remind you to remove the key. Sentry key immobilizer system the sentry key immobilizer system (skis) prevents unauthorized operation of the vehicle by disabling the engi...

  • Page 17

    Note: • the sentry key immobilizer system is not compatible with remote starting systems. Use of these systems may result in vehicle starting problems and loss of security protection. • mobil speedpass™, additional sentry keys, or any other transponder equipped components on the same keychain will n...

  • Page 18

    Consists of programming a blank key to the vehicle electronics. A blank key is one which has never been programmed. Note: when having the sentry key system serviced, bring all vehicle keys to the dealer. Customer key programming you can program new keys to the system if you have two valid keys by do...

  • Page 19

    2. This device must accept any interference that may be received, including interference that may cause undes- ired operation. Steering wheel lock — if equipped your vehicle may be equipped with a passive steering wheel lock (manual transmission only). This lock pre- vents steering the vehicle witho...

  • Page 20

    Doors and door locks the vacuum fluorescent (vf) display located in the odometer area displays the word “door” as an indication of a door ajar or door not completely closed. When the vehicle is not moving and the door is ajar or not completely closed, the vf display will show the word “door” and the...

  • Page 21

    Chime for each complete display cycle (three cycles total). After this, the display will continue to cycle only (no chimes). If the trip/reset button is pressed while the vf warnings are being displayed, the vf display will revert back to only displaying the odometer/trip odometer mileage. Manual do...

  • Page 22

    Warning! • for personal security, and safety in the event of an accident, lock the vehicle doors as you drive as well as when you park and leave the vehicle. • when leaving the vehicle always remove the key from the ignition lock, and lock your vehicle. Do not leave children unattended in the vehicl...

  • Page 23

    Power door locks — if equipped a door lock switch is on each front door panel. Press this switch to lock or unlock the doors. If the plunger is down when the door is closed, the door will lock. Therefore, make sure the keys are not inside the vehicle before closing the door. If you press the door lo...

  • Page 24

    Child protection locks the rear doors of your vehicle are equipped with child protection locks. If you push up on the lever on the open edge of the door it cannot be opened from the inside of the vehicle. Push the lever down to disengage the child protection locks. Warning! Avoid trapping anyone in ...

  • Page 25

    Remote keyless entry this system allows you to lock or unlock the doors or open the swing gate flip-up window from distances of 23–50 feet (7–15 meters) using a transmitter. You don’t have to point the transmitter at the vehicle to activate the system. Each vehicle comes with two transmitters. To un...

  • Page 26

    4. Repeating steps 1–3 will restore original operation. Note: the light flash can be enabled or disabled (within 23–50 feet (7–15 meters) of the vehicle) by per- forming the following procedure: 1. Press and hold the ⬙lock⬙ button on the transmitter. 2. Continue to hold the ⬙lock⬙ button, wait at le...

  • Page 27

    Warning! To avoid injury stand back when opening. Glass will automatically rise. Note: the transmitter can be programmed to unlatch the flip-up window immediately upon activation of the “rear release” button (without pressing and holding) (within 23–50 feet (7–15 meters) of the vehicle) by per- form...

  • Page 28

    To program additional transmitters note: if vehicle is equipped with the optional elec- tronic vehicle information center (evic) in the overhead console, the transmitters may also be programmed through the evic display. For additional information, refer to “overhead console — if equipped” in section...

  • Page 29

    2. This device must accept any interference that may be received, including interference that may cause undes- ired operation. If your remote keyless entry fails to operate from a normal distance, check for these two conditions: 1. Weak batteries in transmitter. The expected life of batteries is fro...

  • Page 30

    Security alarm system — if equipped this system monitors the vehicle doors, swing gate, swing gate flip-up window, and ignition for unautho- rized operation. When the alarm is activated, the system provides both audible and visual signals. The horn, headlights, and tail lights will sound/flash repea...

  • Page 31

    To disarm the system to disarm the system, you will need to press the “un- lock” button on the remote keyless entry transmitter or turn the ignition key to the run position. If something has triggered the system in your absence, the horn will sound three times when you unlock the doors. Check the ve...

  • Page 32

    To open the swing gate, pull the gate handle to its first detent to open just the flip-up window. Pull the handle to its second detent (all the way) to open both the flip-up window and swing gate. Warning! To avoid injury stand back when opening. Glass will automatically rise. The vacuum fluorescent...

  • Page 33

    Evic display (not in the instrument cluster). For addi- tional information, refer to “overhead console — if equipped” in section 3. If any other active warnings including “door” or “lo- wash” are present, they will be shown in the vf display and will also continue to cycle. If the vehicle is moving,...

  • Page 34

    Open (one chime for each complete display cycle). After this, the vf display will continue to sequence only (no chimes). If the trip/reset button is pressed while the vf warnings are being displayed, the vf display will revert back to only displaying the odometer/trip odometer mileage. Note: close s...

  • Page 35

    Windows power windows — if equipped the power window switches are located on the center floor console. The top left switch controls the left front window and the top right switch controls the right front window. The lower left switch controls the left rear passenger window, and the lower right switc...

  • Page 36

    Auto down feature — if equipped the driver’s and passenger’s front window switches have an auto down feature. Press the window switch past the detent, release, and the window will go down auto- matically. To open the window part way, press the window switch part way and release it when you want the ...

  • Page 37

    Windows down, or the sunroof (if equipped) in certain open or partially open positions. This is a normal occur- rence and can be minimized. If the buffeting occurs with the sunroof open, adjust the sunroof opening to minimize the buffeting. Occupant restraints some of the most important safety featu...

  • Page 38

    Research has shown that seat belts save lives, and they can reduce the seriousness of injuries in a collision. Some of the worst injuries happen when people are thrown from the vehicle. Seat belts reduce the possibility of ejection and the risk of injury caused by striking the inside of the vehicle....

  • Page 39

    Lap/shoulder belt operating instructions 1. Enter the vehicle and close the door. Sit back and adjust the seat. 2. The seat belt latch plate is above the back of your seat. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to make the belt go aroun...

  • Page 40

    3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” warning! A belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt ...

  • Page 41

    4. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap portion, pull up a bit on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision. No...

  • Page 42

    Warning! A lap belt worn too high can increase the risk of injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdo- men. Always wear the lap part of your seat belt as low as possible and keep it snug. A twisted belt cannot do its job as well. In a col...

  • Page 43

    Adjustable upper shoulder belt anchorage in the front seat positions, the shoulder belt can be adjusted upward or downward to position the belt away from your neck. To lower the shoulder belt height, push the button and slide the height adjuster down. To raise the height of the shoulder belt, slide ...

  • Page 44

    Warning! Position the shoulder belt height adjusters so that the belt rests across the middle of your shoulder. Failure to adjust the safety belt properly could reduce the effectiveness of the seat belt and increase the risk of injury in a collision. As a guide, if you are shorter than average, you ...

  • Page 45

    Energy management feature this vehicle has a safety belt system with an energy management feature at the driver and front passenger seating positions to help further reduce the risk of injury in the event of a head-on collision. This safety belt system has a retractor assembly that is designed to pa...

  • Page 46

    Seat belt pretensioners the driver and front passenger seat belts are equipped with a pretensioning device that is designed to remove any slack from the seat belt systems in the event of a collision. This device improves the performance of the seat belt by assuring that the belt is tight around the ...

  • Page 47

    The enhanced warning system (beltalert) can be en- abled or disabled by your authorized dealer or by following these steps: note: the following steps must occur within the first 60 seconds of the ignition switch being turned to the on or start position. The manufacturer does not recom- mend deactiva...

  • Page 48

    Seat belt extender if a seat belt is too short, even when fully extended and when the adjustable upper shoulder belt anchorage (if equipped) is in its lowest position, your authorized dealer can provide you with a seat belt extender. This extender should be used only if the existing belt is not long...

  • Page 49

    The instrument panel, above the glove compartment. The words srs/airbag are embossed on the airbag covers. Note: the front airbags are certified to the federal regulations that allow less forceful deployment. The front airbags have a multi stage inflator design. This may allow the airbag to have dif...

  • Page 50

    Warning! • do not put anything on or around the front airbag covers or attempt to manually open them. You may damage the airbags and you could be injured be- cause the airbags are not there to protect you. These protective covers for the airbag cushions are de- signed to open only when the airbags a...

  • Page 51

    Airbags work, you need the seat belts to keep you in the right position for the airbags to protect you properly. Here are some simple steps you can take to minimize the risk of harm from a deploying airbag. 1. Children 12 years and under should always ride buckled up in a rear seat in an appropriate...

  • Page 52

    Warning! • relying on the airbags alone could lead to more severe injuries in a collision. The airbags work with your seat belt to restrain you properly. In some collisions the airbags won’t deploy at all. Always wear your seat belts even though you have airbags. • being too close to the steering wh...

  • Page 53

    • driver and front passenger seat belt pretensioners • front passenger seat occupant classification system (ocs) − occupant classification module − passenger airbag disabled (pad) indicator light − interconnecting wiring − pressure sensor, bladder assembly, and belt tension sensor how the airbag sys...

  • Page 54

    In any part of the system, it turns on the airbag warning light either momentarily or continuously. A single chime will sound if the light comes on again after initial start up. Warning! Ignoring the airbag warning light in your instru- ment panel could mean you won’t have the airbags to protect you...

  • Page 55

    • the side impact srs window bags are designed to activate only in certain side collisions. When the orc (with side impact option) detects a collision requiring the window bags to inflate, it signals the inflators on the crash side of the vehicle. A quantity of nontoxic gas is generated to inflate t...

  • Page 56

    If there is a fault present in the system, the airbag warning light will light indicating that you should take the vehicle to an authorized dealer. In the pres- ence of an occupant in the passenger seat, if both the pad indicator light (located in the front passenger grab handle) and airbag warning ...

  • Page 57

    Should always use the pad indicator light as an indica- tion if the front passenger is properly positioned or not. If the pad indicator light comes on when an adult is in the passenger seat, have the passenger re-position them- selves in the seat until the light goes out. Remember, if the pad indica...

  • Page 58

    • the belt tension sensor (bts) is located at the outboard passenger lap belt anchor. The bts creates a signal based on outboard lap belt tension. This signal is sent to the ocm to ensure that the resultant bladder pressure increase due to applied lap belt tension does not cause a small occupant to ...

  • Page 59

    • do not use prior or future model year seat covers not designated for the specific model being repaired. Al- ways use the correct seat cover specified for the vehicle. • do not replace the seat cover with an aftermarket seat cover. • do not add a secondary seat cover other than those approved by da...

  • Page 60

    However, if you haven’t healed significantly within a few days, or if you have any blistering, see your doctor immediately. As the airbags deflate you may see some smoke-like particles. The particles are a normal by- product of the process that generates the nontoxic gas used for airbag inflation. T...

  • Page 61

    Enhanced accident response system (e.A.R.S.) if the airbags deploy after an impact and the electrical system remains functional, the interior lights will turn on and the power door locks (if equipped) will unlock 5 seconds after airbag deployment. Also, the fuel system will shut off immediately upon...

  • Page 62

    Maintaining your airbag system warning! • modifications to any part of the airbag system could cause it to fail when you need it. You could be injured if the airbag system is not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the stee...

  • Page 63

    Child restraint everyone in your vehicle needs to be buckled up all the time — babies and children, too. Every state in the united states and all canadian provinces require that small children ride in proper restraint systems. This is the law, and you can be prosecuted for ignoring it. Children 12 y...

  • Page 64

    Infants and small children there are different sizes and types of restraints for children from newborn size to the child almost large enough for an adult seat belt. Always check the child seat owner’s manual to ensure you have the right seat for your child. Use the restraint that is correct for your...

  • Page 65

    • children who weigh more than 20 lbs (9 kg) and who are older than one year can ride forward-facing in the vehicle. Forward-facing child seats and convertible child seats used in the forward-facing direction are for children who weigh 20 to 40 lbs (9 to 18 kg), and are older than one year old. Thes...

  • Page 66

    Standards. The manufacturer recommends that you try a child restraint in the vehicle seats where you will use it before you buy it. • the restraint must be appropriate for your child’s weight and height. Check the label on the restraint for weight and height limits. • carefully follow the instructio...

  • Page 67

    Latch — child seat anchorage system (lower anchors and tether for ch ildren) your vehicle’s rear seat is equipped with the child restraint anchorage system called latch. The latch system provides for the installation of the child restraint without using the vehicle’s seat belts, instead securing the...

  • Page 68

    Installing the latch-compatible child restraint system we urge that you carefully follow the directions of the manufacturer when installing your child restraint. Not all child restraint systems will be installed as described here. Again, carefully follow the installation instructions that were provi...

  • Page 69

    In addition, there are tether strap anchorages behind each rear seating position located on the back of the seat. Many, but not all restraint systems will be equipped with separate straps on each side, with each having a hook or connector for attachment to the lower anchorage and a means of adjustin...

  • Page 70

    Downward into the seat, removing slack in the straps according to the child restraint manufacturer’s instruc- tions. Warning! Improper installation of a child restraint to the latch anchorages can lead to failure of an infant or child restraint. The child could be badly injured or killed. Follow the...

  • Page 71

    Buckle and twist the short buckle-end belt several times to shorten it. Insert the latch plate into the buckle with the release button facing out. If the belt still can’t be tightened, or if by pulling and pushing on the restraint loosens the belt, you may need to do something more. Disconnect the l...

  • Page 72

    Warning! An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchor positions directly behind the child seat to secure a child restraint top tether strap. Children too large for booster seats children who are large enough to wear th...

  • Page 73

    Engine break-in recommendations a long break-in period is not required for the engine in your new vehicle. Drive moderately during the first 300 miles (500 km). After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable. While cruising, brief full-throttle accelerat...

  • Page 74

    Garage, and never sit in a parked vehicle with the engine running for a extended period. If the vehicle is stopped in an open area with engine running for more than a short period, adjust the ventilation system to force fresh, outside air into the vehicle. • guard against carbon monoxide with proper...

  • Page 75

    Defrosters check operation by selecting the defrost mode and place the blower control on high speed. You should feel the air directed against the windshield. Safety checks you should make outside the vehicle tires examine tires for excessive tread wear or uneven wear patterns. Check for stones, nail...

  • Page 77: Contents

    Understanding the features of your vehicle contents 䡵 mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81 ▫ inside day/night mirror . . . . . . . . . . . . . . . . .81 ▫ inside automatic dimming mirror — if equipped . . . . . . . . . . . . . . . . . . . . . . . . . .82 ▫ outside ...

  • Page 78

    ▫ front seat adjustment — recline . . . . . . . . . . 109 ▫ head restraints . . . . . . . . . . . . . . . . . . . . . . 110 ▫ power seat adjuster — if equipped . . . . . . . . 111 ▫ heated seats — if equipped . . . . . . . . . . . . . 112 ▫ 65/35 split folding rear seat . . . . . . . . . . . . . 113...

  • Page 79

    䡵 electronic speed control . . . . . . . . . . . . . . . . . . 127 ▫ to activate . . . . . . . . . . . . . . . . . . . . . . . . . . 127 ▫ to set at a desired speed . . . . . . . . . . . . . . . 128 ▫ to deactivate . . . . . . . . . . . . . . . . . . . . . . . . 128 ▫ to resume speed . . . . . . . ....

  • Page 80

    ▫ cargo tie-down hooks . . . . . . . . . . . . . . . . . 152 ▫ cargo organizer — if equipped . . . . . . . . . . . 154 䡵 rear window features . . . . . . . . . . . . . . . . . . . 156 ▫ rear window wiper/washer . . . . . . . . . . . . . 156 ▫ rear window defroster . . . . . . . . . . . . . . . . . 1...

  • Page 81

    Mirrors inside day/night mirror the mirror should be adjusted to center on the view through the rear window. A two-point pivot system allows for horizontal and vertical adjustment of the mirror. The mirror should be adjusted while set in the day position (toward windshield). Annoying headlight glare...

  • Page 82

    Inside automatic dimming mirror — if equipped this mirror automatically adjusts for annoying headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light in the button will indicate when the dimming feature is activated. Cauti...

  • Page 83

    Warning! Vehicles and other objects seen in the right side convex mirror will look smaller and farther away than they really are. Relying too much on your right side mirror could cause you to collide with another vehicle or other objects. Use your inside mirror when judging the size or distance of a...

  • Page 84

    Heated remote control mirrors — if equipped these mirrors are heated to melt frost or ice. This feature is activated whenever you turn on the rear window defrost. Illuminated vanity mirrors — if equipped an illuminated vanity mirror is on the sun visor. To use the mirror, rotate the sun visor down a...

  • Page 85

    Hands–free communication (uconnect™) — if equipped uconnect™ is a voice-activated, hands-free, in vehicle communications system. Uconnect™ allows you to dial a phone number with your cellular phone* using simple voice commands (e.G., ⬙call ѧ mike ѧwork⬙ or ⬙dial ѧ 248-555-1212 ⬙). Your cellular phon...

  • Page 86

    With the system at a time. The system is available in english, spanish, or french languages (as equipped). The rearview mirror contains the microphone for the system and the control buttons that will enable you to access the system. The diagram below shows the mirror with the appropriate buttons. In...

  • Page 87

    The uconnect™ system is fully integrated with the vehicle’s audio system. The volume of the uconnect™ system can either be adjusted from the radio volume control knob, or from the steering wheel radio control (right switch), if so equipped. The radio display will be used for visual prompts from the ...

  • Page 88

    Help command if you need assistance at any prompt or if you want to know what your options are at any prompt, say ⬙help⬙ following the voice on beep. The uconnect™ system will play all the options at any prompt if you ask for help. To activate the uconnect™ system from idle, simply press the ’phone’...

  • Page 89

    • you will be asked to say a four-digit pin number which you will later need to enter into your cellular. You can enter any four-digit pin number. You will not need to remember this pin number after the initial pairing process. • the uconnect™ system will then prompt you to begin the cellular phone ...

  • Page 90

    • for example, you can say ⬙234-567-8901.⬙ the phone number that you enter must be of valid length and combination. The uconnect™ limits the user from dialing invalid combination of numbers. For example, 234-567-890 is nine digits long, which is not a valid phone number - the closest valid phone num...

  • Page 91

    • when prompted, say the name of the new entry. Use of long names helps the voice recognition and is recom- mended. For example, say ⬙robert smith⬙ or ⬙robert⬙ instead of ⬙bob.⬙ • when prompted, enter the number designation (e.G.: ⬙home,⬙ ⬙work,⬙ ⬙mobile,⬙ or ⬙pager⬙). This will allow you to store m...

  • Page 92

    After you are finished editing an entry in the phonebook, you will be given the opportunities to edit another entry in the phonebook, call the number you just edited, or return to the main menu. ⬙phonebook edit⬙ can be used to add another phone number to a name entry that already exists in the phone...

  • Page 93

    • the uconnect™ system will ask you to verify that you wish to delete all the entries from the phonebook. • after confirmation, the phonebook entries will be deleted. List all names in the uconnect™ phonebook • press the ’phone’ button to begin. • after the ⬙ready⬙ prompt and the following beep, say...

  • Page 94

    Answer or reject an incoming call - call currently in progress if a call is currently in progress and you have another incoming call, you will hear the same network tones for call waiting that you normally hear when using your cell phone. Press the ’phone’ button to place the current call on hold an...

  • Page 95

    Conference call when two calls are in progress (one active and one on hold), press and hold the ’phone’ button until you hear a double beep indicating that the two calls have been joined into one conference call. Three-way calling to initiate three-way calling, press the ’voice recogni- tion’ button...

  • Page 96

    • after ignition key is switched to off, a call can continue on the uconnect™ system for certain duration, after which the call is automatically transferred from the uconnect™ system to the mobile phone. • an active call is automatically transferred to the mobile phone after ignition key is switched...

  • Page 97

    • after the ⬙ready⬙ prompt and the following beep, say ⬙emergency⬙ and the uconnect™ system will instruct the paired cellular phone to call the emergency num- ber. This feature is only supported in the usa. Note: the emergency number dialed is based on the country where the vehicle is purchased (911...

  • Page 98

    Paging to learn how to page, refer to section ⬙working with automated systems. ⬙ paging works properly except for pagers of certain companies which time-out a little too soon to work properly with the uconnect™ system. Voice mail calling to learn how to access your voice mail, refer to section ⬙work...

  • Page 99

    Turning confirmation prompts on/off turning confirmation prompts off will stop the system from confirming your choices (e.G. The uconnect™ sys- tem will not repeat a phone number before you dial it). • press the ’phone’ button to begin. • after the ⬙ready⬙ prompt and the following beep, say ⬙setup c...

  • Page 100

    Mute/un-mute (mute off) when you mute the uconnect™ system, you will still be able to hear the conversation coming from the other party, but the other party will not be able to hear you. In order to mute the uconnect™ system: • press the ’voice recognition’ button. • after the ⬙ready⬙ prompt and the...

  • Page 101

    Connect or disconnect link between the uconnect™ system and cellular phone your cellular phone can be paired with many different electronic devices, but can only be actively ⬙connected⬙ with one electronic device at a time. If you would like to connect or disconnect the blue- tooth™ connection betwe...

  • Page 102

    • when prompted say the priority number of the cellu- lar phone you wish to select. You can also press the ⬘voice recognition’ button anytime while the list is being played and say the priority number. • the selected phone will be used for the next phone call. If the selected phone is not available,...

  • Page 103

    • performance is maximized under: • low-to-medium blower setting, • low-to-medium vehicle speed, • low road noise, • smooth road surface, • fully closed windows, • dry weather condition. • even though the system is designed for users speaking in north american english and spanish accents, the system...

  • Page 104

    • smooth road surface, • fully closed windows, and • dry weather condition. • operation from driver seat. • performance, such as, audio clarity, echo. And loud- ness to a large degree, rely on the phone and network, and not the uconnect™ system. • echo at far end can sometime be reduced by lowering ...

  • Page 105

    Understanding the features of your vehicle 105 3.

  • Page 106

    106 understanding the features of your vehicle.

  • Page 107

    Understanding the features of your vehicle 107 3.

  • Page 108

    North american english primary alternate(s) zero oh add location add new all all of them confirmation prompts confirmations prompts delete a name delete language select language list names list all list paired phones list phones pager beeper phone pairing pairing phonebook phone book return to main ...

  • Page 109

    Using body pressure, move forward and rearward on the seat to be sure the seat adjusters have latched. Warning! • adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be ...

  • Page 110

    Head restraints head restraints can reduce the risk of whiplash injury in the event of impact from the rear. Adjustable head restraints should be adjusted so that the upper edge is as high as practical. The head restraints have a locking button that must be pushed inward to lower the head restraint....

  • Page 111

    Power seat adjuster — if equipped warning! Do not ride with the seatback reclined so that the seat belt is no longer resting against your chest. In a collision you could slide under the seat belt and be seriously or even fatally injured. Use the recliner only when the vehicle is parked. 6–way power ...

  • Page 112

    This seat also has a manual recline lever located just to the rear of the power seat switch. Pull up on the lever to recline the seat. Heated seats — if equipped the heated seat switch is located on the outboard side of the front seats. Pressing this switch to its desired setting (hi or lo) will act...

  • Page 113

    Once the heated seat switch is activated, depressing it a second time will de-activate it. 65/35 split folding rear seat to provide additional storage area, each rear seat can be folded flat to allow for extended cargo space and still maintain some rear seating room. Note: prior to folding the rear ...

  • Page 114

    To fold the 65/35 rear seat, perform the following steps: 1. Locate the seatback release handle on the outboard top side of each rear seatback; lift up on the handle, and rotate the lever forward until the seatback releases. Fold the seatback completely forward. Note: when lifting up on the release ...

  • Page 115

    To restore the 65/35 rear seat to the upright position perform the following steps: raise the seatback and lock it into place. If interference from the cargo area prevents the seatback from fully locking, you will have difficulty returning the seat to its proper position. The seat release handle wil...

  • Page 116

    To open and close the hood to open the hood, two latches must be released. First pull the hood release lever inside your vehicle located under the left side of the instrument panel. Then, reach under the hood and slide the safety latch to the right and lift the hood. To prevent possible damage, do n...

  • Page 117

    Secure both latches. Never drive your vehicle unless the hood is fully closed, with both latches engaged. Warning! If the hood is not fully latched, it could fly up when the vehicle is moving and block your forward vision. Be sure all hood latches are latched fully before driving. Lights interior li...

  • Page 118

    Daytime brightness feature certain components (odometer, radio, etc.) can be illumi- nated at full brightness during the daytime. This can be helpful when driving with your headlights on during the daytime such as in a parade or a funeral procession. To activate this feature, rotate the multi-functi...

  • Page 119

    Parking lights, instrument panel lights, and headlights turn the end cap of the multi-function control lever to the first detent for parking lights and instrument panel lights. Turn to the second detent for headlight operation. To change the brightness of the instrument panel lights, rotate the cent...

  • Page 120

    Note: a tone will chime if the turn signals are left on for more than 2 miles (3.2 km). Lights-on reminder a chime will sound if the driver’s door is left open, and the headlights or parking lights are left on. Battery saver feature — exterior lights if the park lights, headlights, fog lights, or hi...

  • Page 121

    Light bar — if equipped 1. Remove lamp covers by pressing the thumb tab up- wards, and pulling the cover off. Caution! The auxiliary lights mounted on the off road light bar should be illuminated during ⴖoff-road use only. ⴖ having them illuminated on public streets, highways, roads, etc. May be ill...

  • Page 122

    2. With the ignition in the on position, press the button to turn on the light bar (located on the instrument panel to the left of the steering column). Press the button again to turn off the light bar. An indicator light in the instrument cluster will illumi- nate when the light bar has been activa...

  • Page 123

    Windshield wipers and washers the wipers and washers are operated by a switch on the control lever. This control lever is located on the right side of the steering column. For front wiper operation, turn the control lever end cap upward to select the desired wiper speed. Windshield wiper/washer swit...

  • Page 124

    Windshield washers to use the washer, pull the lever toward you and hold while spray is desired. If the lever is pulled while in the delay range, the wiper will operate for two wipe cycles after the lever is released, and then resume the intermit- tent interval previously selected. Note: if vehicle ...

  • Page 125

    Mist feature push down on the wiper lever to activate a single wipe to clear off road mist or spray from a passing vehicle. As long as the lever is held down, the wipers will continue to operate. Caution! In cold weather, always turn off the wiper switch and allow the wipers to return to the park po...

  • Page 126

    Tilt steering column to tilt the column, push down on the lever below the turn signal control and move the wheel up or down, as desired. Pull the lever back towards you and firmly push the lever until it is above the lower surface of the shroud to lock the column in place. Tilt steering column 126 u...

  • Page 127

    Warning! Tilting the steering column while the vehicle is moving is dangerous. Without a stable steering col- umn, you could lose control of the vehicle and have an accident. Adjust the column only while the ve- hicle is stopped. Be sure it is locked before driving. Electronic speed control when eng...

  • Page 128

    To set at a desired speed when the vehicle has reached the desired speed, press and release the set button. Release the accelerator and the vehicle will operate at the selected speed. To deactivate a soft tap on the brake pedal, normal braking, or pressing the cancel button will deactivate the speed...

  • Page 129

    To accelerate for passing depress the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed. Note: when driving uphill, at elevations above 2,000 ft. (610 meters), or when the vehicle is heavily loaded (especially when towing) the vehicle may slow be...

  • Page 130

    Pressing the menu button will change the displayed programming features. Pressing the step button will select the available choices. Pressing the c/t (compass/ temperature) button will return the display to the normal compass/temperature display. Note: temperature accuracy can be effected from heat ...

  • Page 131

    The reading lights are activated by pressing on the recessed area of the corresponding lens. Note: the dome/reading lights will remain on until the switch is pressed a second time, so be sure they have been turned off before leaving the vehicle. Electronic vehicle information center the electronic v...

  • Page 132

    Customer programmable features press the menu button until one of the display choices following appears: language? When in this display you may select one of five lan- guages for all display nomenclature, including the trip computer functions. Press the step button while in this display to select en...

  • Page 133

    All doors. This can also be programmed using the key fob, refer to “remote keyless entry” earlier in this section. Train remote? Pressing the step button when in this display will select “yes” or “no.” note: any time you perform this procedure, it is necessary to retrain all currently trained key fo...

  • Page 134

    Flash lights with locks? When this feature is selected, the front and rear turn signals will flash when the doors are locked or unlocked using the remote keyless entry transmitter. This feature may be selected with or without the sound horn on lock feature selected. Pressing the step button when in ...

  • Page 135

    Mini-trip computer this feature, located in the overhead console, displays information on outside temperature, compass direction, and trip information. Reset button use this button to reset the average economy, trip miles, and time elapsed displays to zero. This will occur only if a resettable funct...

  • Page 136

    Warning! Even if the display still reads a few degrees above 32°f (0°c), the road surface may be icy, particularly in woods or on bridges. Drive carefully under such conditions to prevent an accident and possible per- sonal injury or property damage. Step button press the step button to cycle throug...

  • Page 137

    Tire psi shows the pressure and location of each tire, except for the spare tire. The tire location will blink when under pressure. Blank screen shows a blank screen. Pressing the c/t button returns to the compass and temperature display. Pressing the step button returns you to the average miles per...

  • Page 138

    Compass variance is the difference between magnetic north and geographic north. In some areas of the country, the difference between magnetic and geographic north is great enough to cause the compass to give false readings. If this occurs, the compass variance must be set according to the compass va...

  • Page 139

    General information this transmitter complies with fcc rules part 15 and with rss-210 of industry canada. Operation is subject to the following two conditions: 1. This device may not cause harmful interference 2. This device must accept any interference that may be received, including interference t...

  • Page 140

    Warning! Before programming homelink to a garage door opener or gate operator, make sure that people and objects are out of the way of the device to prevent potential harm or damage. When programming a garage door opener, it is advised to park outside of the garage. Do not use homelink with any gara...

  • Page 141

    Programming homelink note: it is recommended that a new battery be placed in the hand-held transmitter of the device being pro- grammed to homelink for quicker training and accurate transmission of the radio frequency signal. Warning! Vehicle exhaust contains carbon monoxide, a danger- ous gas. Do n...

  • Page 142

    2. Simultaneously press and hold both the desired homelink button and the hand-held transmitter button. After a short time, the message training will show on homelink display. Do not release the buttons until the next step has been completed. 3. When the message trained appears on the homelink displ...

  • Page 143

    If the message transmit appears on the homelink display but your device does not activate, the device may be equipped with a ⬙rolling code⬙ system. Continue with steps five through seven below to complete the program- ming of a rolling code equipped device (most commonly a garage door opener). 5. At...

  • Page 144

    If, after programming the homelink wireless control system, the hand-held transmitter and/or other homelink units in other vehicles fail to activate the rolling code equipped device, you may need to clear (or ⴖeraseⴖ) the device’s receiver memory. Refer to your garage door opener’s owner’s manual fo...

  • Page 145

    Press and hold the homelink button while you press and release - every two seconds ( ⴖcycleⴖ) your hand-held transmitter button until the radio signal has success- fully been accepted by homelink. (the message trained will appear on the homelink display.) proceed with the remaining steps under ⬙prog...

  • Page 146

    Press and hold the switch rearward to fully open the sunroof. The sunroof can be stopped at any position between closed and full open. Momentarily pressing the switch rearward will activate the express open feature, causing the sunroof to open automatically. Press and hold the “v” button in the cent...

  • Page 147

    The sunroof and the sunroof will remain in the partial vent position until the switch is pushed forward again. Express open feature during the express open operation, any movement of the switch will stop the sunroof and it will remain in a partial open position. Again, momentarily pressing the switc...

  • Page 148

    Power outlet to the right of the convenience tray (lower center of instrument panel) is an outlet for electrically powered accessories. Pull lightly on the top of the plastic cover to open the outlet. There is a rear power outlet located in the right rear cargo area above the storage cargo net/cd ch...

  • Page 149

    The rear power outlet is a direct feed from the battery so it receives power whether the ignition is in the on or off position. All accessories connected to this outlet should be re- moved or turned off when the vehicle is not in use. Caution! Electrical outlet use with engine off • many accessories...

  • Page 150

    Cup holders in the center console there are two cup holders for the front seat passengers. Note: the front cup holder insert is removable from the console, for cleaning. Smoker’s package — if equipped with the optional smoker’s package, a removable ash tray is inserted into the front cup holder loca...

  • Page 151

    Cargo area features cargo light the cargo area light is activated by opening the swing gate, opening any door, or by rotating the dimmer control on the multi-function control lever to the extreme top position. If all doors are closed and only the swing gate is open, pushing on the cargo light lens s...

  • Page 152

    Warning! In an accident a cargo cover loose in the vehicle could cause injury. It could fly around in a sudden stop and strike someone in the vehicle. Do not store the cargo cover on the cargo floor or in the passenger compart- ment. Remove the cover from the vehicle when taken from its mounting. Do...

  • Page 153

    Warning! • cargo tie-down hooks are not safe anchors for a child seat tether strap. In a sudden stop or colli- sion a hook could pull loose and allow the child seat to come loose. A child could be badly injured. Use only the anchors provided for child seat tethers. • the weight and position of cargo...

  • Page 154

    Cargo organizer — if equipped this vehicle may be equipped with a cargo organizer that mounts on the floor behind the rear seat. Items may be placed on the flat surface or stored in the three storage compartments. Warning! • to avoid tipping, lock the shelf securely in all positions. • do not drive ...

  • Page 155

    2. Place the rear corners of the cargo organizer into the supports located on the rear trim panel. Press down on the back of the cargo organizer to lock it into place. Warning! Do not load objects over 30 lbs (13.5 kg) in the upper position. Failure to follow this warning could cause the cargo organ...

  • Page 156

    To open storage compartments 1. Pull up on the center opening of the cargo organizer. 2. Lift up on the storage compartment dividers and lock into place. Cargo organizer removal loosen screw, then lift lever from each mount located on the floor of the rear cargo area, and remove the cargo organizer ...

  • Page 157

    If the rear wiper is operating when the ignition is turned off, the wiper will automatically return to the “park” position. When the vehicle is restarted, the wiper will resume function at whichever position the switch is set at. If the swing gate flip-up window is open or the swing gate is open, co...

  • Page 158

    Rear window defroster on the top of the climate control panel is a push button for rear window defrosting. An amber indicator in the push button will light when the defroster is turned on. Push again to turn off the defroster prior to an automatic time-out. The defroster will automatically turn off ...

  • Page 159

    Roof luggage rack external racks do not increase the total load carrying capacity of the vehicle. Be sure that the total occupant and luggage load inside the vehicle, plus the load on the luggage rack, do not exceed the rated vehicle capacity as shown on the label attached to the drivers door shut f...

  • Page 160

    Warning! Cargo must be securely tied before driving your vehicle. Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in personal injury or property damage. Follow the roof rack “cautions” when carrying cargo on your roof rack. 160 understanding the features of y...

  • Page 161: Contents

    Understanding your instrument panel contents 䡵 instrument panel and interior controls . . . . . . . 165 䡵 instrument cluster . . . . . . . . . . . . . . . . . . . . . . 166 ▫ 2.4l/3.7l engines . . . . . . . . . . . . . . . . . . . . . 166 ▫ 2.8l diesel engines . . . . . . . . . . . . . . . . . . . ....

  • Page 162

    ▫ tuning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 179 ▫ radio data system (rds) . . . . . . . . . . . . . . . 179 ▫ pty (program type) button . . . . . . . . . . . . . . 179 ▫ balance . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181 ▫ fade . . . . . . . . . . . . . . . . ...

  • Page 163

    ▫ mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 186 ▫ tape cd button . . . . . . . . . . . . . . . . . . . . . . 186 ▫ time button . . . . . . . . . . . . . . . . . . . . . . . . . 187 ▫ scan button . . . . . . . . . . . . . . . . . . . . . . . . . 187 ▫ cd changer control capabil...

  • Page 164

    ▫ using the pty (program type) button (if equipped) . . . . . . . . . . . . . . . . . . . . . . . . 206 ▫ pty button ⬙scan⬙ . . . . . . . . . . . . . . . . . . . . . 206 ▫ pty button ⬙seek⬙ . . . . . . . . . . . . . . . . . . . . . 207 ▫ satellite antenna . . . . . . . . . . . . . . . . . . . . . . ...

  • Page 165

    Instrument panel and interior controls understanding your instrument panel 165 4.

  • Page 166

    Instrument cluster 2.4l/3.7l engines 166 understanding your instrument panel.

  • Page 167

    2.8l diesel engines understanding your instrument panel 167 4.

  • Page 168

    Instrument cluster description 1. Tachometer indicates the permissible engine revolutions-per-minute for each gear range. Before reaching the red area, ease up on the accelerator to prevent engine damage. 2. Turn signal indicator light the arrows will flash in unison with the exterior turn signals, ...

  • Page 169

    The vehicle’s handling and stopping ability. Each tire, including the spare, should be checked monthly when cold and set to the recommended inflation pressure as specified on the vehicle placard. (see page 268 for more information.) 6. 4lo mode indicator light — if equipped this light alerts the dri...

  • Page 170

    Converter damage. The vehicle should be serviced as soon as possible if this occurs. (see page 309 for more information.) 9. Anti-lock warning light (abs) — if equipped this light monitors the anti-lock brake system (abs) described elsewhere in this manual. This light will come on when the ignition ...

  • Page 171

    11. Temperature gage indicates engine coolant temperature. Any read- ing within the normal range indicates that the cooling system is operating satisfactorily. The gage pointer will likely indicate a higher temperature (above center scale) when driving in hot weather, up mountain grades, in heavy st...

  • Page 172

    Evic display (not in the instrument cluster). For addi- tional information, refer to “overhead console — if equipped” in section 3. U.S. Federal regulations require that upon transfer of vehicle ownership, the seller certify to the purchaser the correct mileage that the vehicle has been driven. Ther...

  • Page 173

    17. Part time indicator light — if equipped this light alerts the driver that the vehicle is in the part time four–wheel drive high range mode, and the front and rear driveshafts are mechanically locked together forcing the front and rear wheels to rotate at the same speed. (see page 236 for more in...

  • Page 174

    Also, the light will come on when the parking brake is applied with the ignition switch in the on position. Note: this light shows only that the parking brake is applied. It does not show the degree of brake application. If the parking brake is off and the light remains on, have the brake system ins...

  • Page 175

    24. O/d (overdrive) off indicator light this light will illuminate when the o/d off button has been selected. The o/d off button is located on the gear shift lever. 25. Seat belt indicator light when the ignition switch is first turned on, this light will turn on for 5 to 8 seconds as a bulb check. ...

  • Page 176

    Off. If the light remains lit with the engine running your vehicle will usually be drivable, however, see your dealer for service as soon as possible. If the light is flashing when the engine is running, immediate service is re- quired and you may experience reduced performance, an elevated/rough id...

  • Page 177

    Radio general information radio broadcast signals your new radio will provide excellent reception under most operating conditions. Like any system, however, car radios have performance limitations, due to mobile op- eration and natural phenomena, which might lead you to believe your sound system is ...

  • Page 178

    Remain active for up to 45 seconds after the ignition switch has been turned off. Opening a vehicle front door will cancel this feature. Sales code raz—am/ fm stereo radio with cassette tape player, cd player and cd changer controls note: the radio sales code is located on the lower left side of you...

  • Page 179

    Tuning press the tune control up or down to increase or decrease the frequency. If you press and hold the button, the radio will continue to tune until you release the button. The frequency will be displayed and continu- ously updated while the button is pressed. Radio data system (rds) the radio da...

  • Page 180

    Program type radio display country country information inform jazz jazz foreign language language news news nostalgia nostalga oldies oldies personality persnlty public public rhythm and blues r & b religious music rel musc religious talk rel talk rock rock soft soft soft rock soft rck soft rhythm a...

  • Page 181

    Pressing pty, then scan will scan the fm band and stop at all rds stations. Each rds station will be played for a 5 second scan once around the fm band and stop at the last station. The pty icon will then turn off. Balance the balance control adjusts the left-to-right speaker bal- ance. Push in the ...

  • Page 182

    To set the radio push-button memory when you are receiving a station that you wish to commit to push-button memory, press the set button. Set 1 will show in the display window. Select the push-button you wish to lock onto this station and press and release that button. If a station is not selected w...

  • Page 183

    Press the seek button up or down to move the track number to skip forward or backward 1 to 6 selections. Press the seek button once to move 1 selection, twice to move 2 selections, etc. Fast forward (ff) press the ff button up momentarily to advance the tape in the direction that it is playing. The ...

  • Page 184

    Pinch roller release if ignition power or the radio on/off switch are turned off, the pinch roller will automatically retract to protect the tape from any damage. When power is restored to the tape player, the pinch roller will automatically reengage and the tape will resume play. Noise reduction th...

  • Page 185

    If the volume control is on, the unit will switch from radio to cd mode and begin to play. The display will show the track number and index time in minutes and seconds. Play will begin at the start of track one. Note: • you may eject a disc with the radio off. The ignition switch must be in the on o...

  • Page 186

    Ff/tune/rw press ff (fast forward) and the cd player will begin to fast forward until ff is released. The rw ( reverse) button works in a similar manner. Program button 4 (random play) press this button while the cd is playing to activate random play. This feature plays the tracks on the se- lected ...

  • Page 187

    Time button press this button to change the display from elapsed cd playing time to time of day. Scan button press this button to play the first 10 seconds of each track. To stop the scan function, press the button a second time. Cd changer control capability — if equipped this radio is compatible w...

  • Page 188

    Random play (rnd) press the random button to play the tracks on the selected disc in random order for an interesting change of pace. Random can be cancelled by pressing the button a second time or by ejecting the cd from the changer. Cd diagnostic indicators when driving over a very rough road, the ...

  • Page 189

    Sales code rbk—am/ fm stereo radio with cd player and cd changer controls note: the radio sales code is located on the lower left side of your radio faceplate. Radio operation power/volume control press the on/vol control to turn the radio on. Turn the volume control clockwise to increase the volume...

  • Page 190

    Tune press the tune control up or down to increase or decrease the frequency. If you press and hold the button, the radio will continue to tune until you release the button. The frequency will be displayed and continu- ously updated while the button is pressed. To set the radio push-button memory wh...

  • Page 191

    Press the audio button a third time and bal will be displayed. Press the seek + or seek – to adjust the sound level from the right or left side speakers. Press the audio button a fourth time and fade will be displayed. Press the seek + or seek – to adjust the sound level between the front and rear s...

  • Page 192

    Inserting the compact disc caution! This cd player will accept 4 3 ⁄ 4 inch (12 cm) discs only. The use of other sized discs may damage the cd player mechanism. You may either insert or eject a disc with the radio off. If you insert a disc with the ignition on and the radio off, the display will sho...

  • Page 193

    Ff/tune/rw press ff (fast forward) and the cd player will begin to fast forward until ff is released. The rw ( reverse) button works in a similar manner. Random play — rnd/program button 4 press the rnd (button 4) button while the cd is playing to activate random play. This feature plays the tracks ...

  • Page 194

    Disc up/program button 1 press the disc up (button 1) button to play the next available disc. Disc down/program button 5 press the disc down (button 5) button to play the previous disc. Seek button press the seek up or down to select another track on the same disc. A seek symbol will appear on the d...

  • Page 195

    Cd hot will pause the operation. Play can be resumed when the operating temperature is corrected or another mode is selected. An err symbol will appear on the display if the laser is unable to read the disc data for the following reasons: • excessive vibration • disc inserted upside down • damaged d...

  • Page 196

    Note: power to operate the radio is controlled by the ignition switch. It must be in the on or acc position to operate the radio. Mode press the mode button repeatedly to select between am, fm, the cd changer and sirius satellite radio™ (if equipped). The display will show st when a stereo station i...

  • Page 197

    And release that button. If a button is not selected within 5 seconds after pressing the set rnd button, the station will continue to play but will not be locked into push- button memory. You may add a second station to each push-button by repeating the above procedure with this exception: press the...

  • Page 198

    General information this radio complies with part 15 of fcc rules and with rss-210 of industry canada. Operation is subject to the following conditions: 1. This device may not cause harmful interference, 2. This device must accept any interference received, including interference that may cause unde...

  • Page 199

    Show the disc number, the track number, and index time in minutes and seconds. Play will begin at the start of track 1. Load/ ejt — load press the load/ ejt button and the button with the corresponding number where the cd is being loaded. After the radio displays “load” insert the cd into the player...

  • Page 200

    Ff/tune/rw press ff (fast forward) and the cd player will begin to fast forward until ff is released. The rw ( reverse) button works in a similar manner. Random play — set / rnd press the rnd button while the cd is playing to activate random play. This feature plays the tracks on the disc in random ...

  • Page 201

    Program type radio display nostalgia nostalga oldies oldies personality persnlty public public rhythm and blues r & b religious music rel musc religious talk rel talk rock rock soft soft soft rock soft rck soft rhythm and blues soft r&b sports sports talk talk top 40 top 40 weather weather by pressi...

  • Page 202

    Time press the time button to change the display from elapsed cd playing time to time of day. Operating instructions - satellite radio mode (if equipped) refer to the satellite radio section of the owner’s manual. Cd diagnostic indicators when driving over a very rough road, the cd player may skip m...

  • Page 203

    Sales code rb1—am/fm stereo radio with dvd/gps navigation system the navigation system provides maps, turn identifica- tion, selection menus and instructions for selecting a variety of destinations and routes. Refer to your “navi- gation user’s manual” for detailed operating instruc- tions. Note: if...

  • Page 204

    System activation to activate your sirius satellite radio service, call the toll-free number 888-539-7474, or visit the sirius web site at www.Sirius.Com. Please have the following informa- tion available when activating your system: 1. The electronic serial number/sirius identification number (esn/...

  • Page 205

    Esn/sid access with rbp, rbu, raz, rb1 and rbq radios with the ignition switch in the accessory position and the radio off, press the cd eject and time buttons simultaneously for 3 seconds. All twelve esn/sid num- bers will be displayed. The radio will exit the esn/sid mode when any other button is ...

  • Page 206

    Selecting a channel press and release the seek or tune buttons to search for the next channel. Press the top of the button to search up and the bottom of the button to search down. Holding the tune button causes the radio to bypass channels until the button is released. Press and release the scan bu...

  • Page 207

    Note: pressing the ⬙seek⬙ or ⬙scan⬙ button while performing a music type scan will change the channel by one and stop the search. Pressing a pre-set memory button during a music type scan, will call up the memory channel and stop the search. Pty button ⴖseekⴖ when the desired program is obtained, pr...

  • Page 208

    Remote sound system controls — if equipped the remote sound system controls are located on the rear surface of the steering wheel. Reach behind the wheel to access the switches. The right hand control is a rocker type switch with a push-button in the center and controls the volume and mode of the so...

  • Page 209

    Radio operation pressing the top of the switch will “seek” up for the next listenable station and pressing the bottom of the switch will “seek” down for the next listenable station. The button located in the center of the left hand control will tune to the next preset station that you have pro- gram...

  • Page 210

    If you press the switch up or down twice it plays the second track, three times, it will play the third, etc. The button in the center of the left hand switch will cause the cd changer to play the next available disc in the 6–disc magazine. Cassette tape and player maintenance to keep the cassette t...

  • Page 211

    As preventive maintenance, clean the head about every 30 hours of use. If you wait until the head becomes very dirty (noticeably poor sound), it may not be possible to remove all deposits with a simple wet cleaning cassette. Cd/dvd disc maintenance to keep the cd/dvd discs in good condition, take th...

  • Page 212

    Climate controls the controls for the heating, air conditioning, and venti- lation system in this vehicle consist of a series of rotary knobs, and a push-button. These comfort controls can be set to obtain desired interior conditions. Blower control the rotary knob on the left controls the blower an...

  • Page 213

    Off this position turns off the blower motor and outside air will not pass through any outlets. Recirculate (max a/c) air flows through the outlets located in the instrument panel. Allows for circulation of interior air only which will cool the cabin faster. This setting can be used in very hot weat...

  • Page 214

    Mix air flows through the floor outlets, the outlets at the base of the windshield, and the side window demisters outlets. Defrost air flows through the outlets at the base of the windshield and through the side window demister outlets. Operating tips fast cool down for a fast cool down, turn the bl...

  • Page 215

    Summer operation air conditioned equipped vehicle’s cooling systems must be protected with a high quality engine coolant during summer to provide proper corrosion protection and to raise the boiling point of the coolant for protection against overheating. A 50% concentration is recom- mended. Winter...

  • Page 217: Starting And Operating

    Starting and operating contents 䡵 starting procedures . . . . . . . . . . . . . . . . . . . . . 220 ▫ manual transmission . . . . . . . . . . . . . . . . . . 220 ▫ automatic transmission . . . . . . . . . . . . . . . . 220 ▫ normal starting — gasoline engines . . . . . . . 221 ▫ normal starting — di...

  • Page 218

    ▫ shift positions . . . . . . . . . . . . . . . . . . . . . . . . 242 ▫ shifting procedure . . . . . . . . . . . . . . . . . . . . 243 䡵 trac-lok™ rear axle — if equipped . . . . . . . . . 245 䡵 parking brake . . . . . . . . . . . . . . . . . . . . . . . . . 245 䡵 anti-lock brake system — if equippe...

  • Page 219

    ▫ tire pressure monitoring — base system . . . . . 268 ▫ tire pressure monitoring — premium system . 270 ▫ general information . . . . . . . . . . . . . . . . . . . 273 䡵 tire chains . . . . . . . . . . . . . . . . . . . . . . . . . . . 274 䡵 tire rotation recommendations . . . . . . . . . . . . 275...

  • Page 220

    Starting procedures before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. Warning! Do not leave children or animals inside parked vehicles in hot weather. Interior heat build up may cause serious injury or death. Manual transmission apply...

  • Page 221

    Normal starting — gasoline engines normal starting of either a cold or a warm engine is obtained without pumping or depressing the accelerator pedal. Turn the key to the start position and release when the engine starts. If the engine fails to start within 10 seconds, turn the key to the off positio...

  • Page 222

    Warning! Never pour fuel or other flammable liquids into the throttle body air inlet opening in an attempt to start the vehicle. This could result in a flash fire causing serious personal injury. If engine fails to start if the engine fails to start after you have followed the “normal starting” proc...

  • Page 223

    If the engine shows no sign of starting after two 15 second periods of cranking with the accelerator pedal held to the floor, the “normal starting” procedure should be repeated. After starting the idle speed is automatically controlled and will de- crease as the engine warms up. Normal starting — di...

  • Page 224

    Turbocharger “cool down” note: letting the engine idle after extended operation allows the turbine housing to cool to normal operating temperature. The following chart should be used as a guide in deter- mining the amount of engine idle time required to sufficiently cool down the turbocharger before...

  • Page 225

    Diesel fuel-water separator a diesel fuel-water separator separates the water nor- mally found in diesel fuel. A manual hand prime pump is located on the filter head for re-priming the fuel system. The fuel-water separator is located on the driver side cowl in the engine compartment. Refer to “2.8l ...

  • Page 226

    3. Depress the fuel-water separator knob 20 consecutive times. 4. Turn the ignition to start and crank the engine a maximum of 10 seconds. If the engine does not start, repeat step 3. Note: the engine will typically start within 10 sec- onds; the engine will idle then stall, purging air from the fue...

  • Page 227

    Warning! Remember to disconnect the cord before driving. Damage to the 110-115 volt ac electrical cord could cause electrocution. Use the heater when temperatures below 0°f (-18°c) are expected to last for several days. Transmission shifting 6-speed manual transmission follow the shift pattern on th...

  • Page 228

    Warning! When parking your vehicle, always leave a manual transmission in first gear and apply the parking brake fully to guard against vehicle movement and possible injury or damage. Never use any gear as a substitute for the parking brake. Caution! To drive as safely as possible and to prolong the...

  • Page 229

    • when “rocking” a stuck vehicle by shifting between a forward gear and reverse, do not spin wheels faster than 15 mph (24 km/h), or drivetrain damage may result. Recommended manual transmission shifting speeds the manufacturer recommends that you use the shift speeds listed in the chart below. Manu...

  • Page 230

    Automatic transmission shifting from d (drive) to p (park) or r (reverse) (or from p or r to d) should be done only after the accelerator pedal is released and the vehicle is stopped. Be sure to keep your foot on the brake when moving the shift lever between these gears. Warning! It is dangerous to ...

  • Page 231

    Gear ranges p (park) supplements the parking brake by locking the transmis- sion. The engine can be started in this range. Never use p (park) while the vehicle is in motion. Apply the parking brake when leaving the vehicle in this range. Always place the gear selector in the p (park) position first,...

  • Page 232

    The following indicators should be used to ensure that you have engaged the transmission shift lever into the p (park) position: • when shifting into p (park), depress the button on the shift lever and firmly move the lever all the way forward until it stops. • look at the shift indicator window on ...

  • Page 233

    Overdrive (o/d) for most city and highway driving. The transmission contains an electronically controlled overdrive, and will automatically shift from d (drive) to o/d (overdrive) if the following conditions are present: • the transmission selector is in d (drive). • the o/d off button has not been ...

  • Page 234

    Note: if the vehicle is started in cold outside tempera- tures, shifts into overdrive may be delayed. Normal overdrive and shifting operation will resume when the temperature of the transmission reaches the appropriate temperature. Refer to the “note” under “torque con- verter clutch” later in this ...

  • Page 235

    Over temperature mode the transmission electronics constantly monitor the transmission oil temperature. If the transmission gets too hot, the transmission will change the way it shifts to help control the condition. This may result in a slightly different feeling or response during normal operation ...

  • Page 236

    Normal condition and will not cause damage to the transmission. The torque converter will refill within 5 seconds of shifting from p (park) into any other gear position. Rocking the vehicle if the vehicle becomes stuck in snow, sand, or mud, it can often be moved by a rocking motion. Move the gear s...

  • Page 237

    When additional traction is required the transfer case 4h and 4l positions can be used to lock the front and rear driveshafts together and force the front and rear wheels to rotate at the same speed. This is accomplished by simply moving the shift lever to these positions. The 4h and 4l positions ar...

  • Page 238

    Proper operation of 4-wheel drive vehicles depends on tires of equal size, type and circumference on each wheel. Any difference will adversely affect shifting and can cause damage to the transfer case. Warning! • because 4-wheel drive provides improved trac- tion, there is a tendency to exceed safe ...

  • Page 239

    4l 4-wheel-drive low range - low speed 4 wheel drive. Locks the front and rear driveshafts together. Forces the front and rear wheels to rotate at the same speed. Additional traction and maximum pulling power for loose, slippery road surfaces only. Do not exceed 25 mph (40 km/h). (allows engine star...

  • Page 240

    Note: shifting into or out of 4l is possible with the vehicle completely stopped, however difficulty may oc- cur due to the mating clutch teeth not being properly aligned. Several attempts may be required for clutch teeth alignment and shift completion to occur. The pre- ferred method is with the ve...

  • Page 241

    The part time indicator light, located on the instru- ment cluster, illuminates when the transfer case is shifted to the 4 part time position. The full time indicator light, located on the instru- ment cluster, illuminates when the transfer case is shifted to the 4 full time position. The 4lo mode i...

  • Page 242

    Proper operation of 4-wheel drive vehicles depends on tires of equal size, type, and circumference on each wheel. Any difference will adversely affect shifting and can cause damage to the transfer case. Warning! • because 4-wheel drive provides improved trac- tion, there is a tendency to exceed safe...

  • Page 243

    N neutral - disengages both the front and rear driveshafts from the powertrain. To be used for flat towing behind another vehicle. Refer to “recreational towing” in sec- tion 5 for more information. 4lo part time 4–wheel drive low range - low speed 4–wheel drive. Locks the transfer case inter-axle d...

  • Page 244

    Shifting. This will allow full engagement of the newly selected position. Apply a constant force when shifting the transfer case lever. 4 full time to 4 lo or 4 lo to 4 full time with the vehicle rolling at 2 to 3 mph (3 to 5 km/h), shift an automatic transmission to n (neutral). While the vehicle i...

  • Page 245

    Trac-lok™ rear axle — if equipped the optional trac-lok™ rear axle provides a constant driving force to both rear wheels and reduces wheel spin caused by the loss of traction at one driving wheel. If traction differs between the two rear wheels, the differ- ential automatically proportions the usabl...

  • Page 246

    To release the parking brake, pull up slightly, press the center button, then lower the lever completely. Before leaving the vehicle parked on a hill, you must make sure the parking brake is fully applied and place the gear selector in the p (park) position. Make certain the transfer case is in gear...

  • Page 247

    Anti-lock brake system — if equipped the anti-lock brake system is designed to aid the driver in maintaining vehicle control under adverse braking conditions. The system operates with a separate com- puter to modulate hydraulic pressure to prevent wheel lock-up and help avoid skidding on slippery su...

  • Page 248

    Warning! Pumping of the anti-lock brakes will diminish their effectiveness and may lead to an accident. Pumping makes the stopping distance longer. Just press firmly on your brake pedal when you need to slow down or stop. Warning! • anti-lock system (abs) cannot prevent the natu- ral laws of physics...

  • Page 249

    Caution! The anti-lock brake system is subject to possible detrimental effects of electronic interference caused by improperly installed aftermarket radios or tele- phones. Note: during severe braking conditions, a pulsing sensation may occur and a clicking noise will be heard. This is normal, indic...

  • Page 250

    Where additional low speed pulling power is needed. Vehicle speeds in excess of 25 mph (40 km/h) should be avoided when in 4l or 4lo range. Driving through water although your vehicle is capable of driving through water, there are a number of precautions that must be considered before entering the w...

  • Page 251

    Standing water avoid driving in standing water deeper than 20 inches, and reduce speed appropriately to minimize wave ef- fects. Maximum speed in 20 inches of water is less than 5 mph (8 km/h). Maintenance after driving through deep water, inspect your vehicle fluids and lubricants (engine oil, tran...

  • Page 252

    Your speed. If the brakes are required to control vehicle speed, apply them lightly and avoid locking or skidding the tires. Warning! If the engine stalls or you lose headway or cannot make it to the top of a steep hill or grade, never attempt to turn around. To do so may result in tipping and rolli...

  • Page 253

    After driving off-road off-road operation puts more stress on your vehicle than does most on-road driving. After going off-road it is always a good idea to check for damage. That way you can get any problems taken care of right away and have your vehicle ready when you need it. • completely inspect ...

  • Page 254

    Tire safety information tire markings note: • p(passenger)-metric tire sizing is based on u.S. Design standards. P-metric tires have the letter “p” molded into the sidewall preceding the size designation. Ex- ample: p215/65r15 95h. • european metric tire sizing is based on european design standards....

  • Page 255

    Tire sizing chart example: size designation: p = passenger car tire size based on u.S. Design standards ⴖ....Blank....ⴖ = passenger car tire based on european design standards lt = light truck tire based on u.S. Design standards t = temporary spare tire 31 = overall diameter in inches (in) 215 = sec...

  • Page 256

    Example: service description: 95 = load index —a numerical code associated with the maximum load a tire can carry. H = speed symbol —a symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions. —the maximum speed corresp...

  • Page 257

    Tire identification number (tin) the tin may be found on one or both sides of the tire however the date code may only be on one side. Tires with white sidewalls will have the full tin including date code located on the white sidewall side of the tire. Look for the tin on the outboard side of black s...

  • Page 258

    Tire loading and tire pressure tire placard location note: the proper cold tire inflation pressure for pas- senger cars is listed on either the face of the driver’s door or the driver’s side “b” pillar. For vehicles other than passenger cars, the cold tire inflation pressures are listed on either th...

  • Page 259

    Tire and loading information placard this placard tells you important information about the: 1) number of people that can be carried in the vehicle 2) the total weight your vehicle can carry 3) the tire size designed for your vehicle 4) the cold tire inflation pressures for the front, rear and spare...

  • Page 260

    Combined weight of occupants, cargo/luggage and trailer tongue weight (if applicable) should never exceed the weight referenced here. Steps for determining correct load limit 1. Locate the statement “the combined weight of occu- pants and cargo should never exceed xxx pounds” on your vehicle’s placa...

  • Page 261

    Starting and operating 261 5.

  • Page 262

    Warning! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. Tires — general information proper tire inflation pressure is essential...

  • Page 263

    2. Economy— improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Under inflation also increases tire rolling resistance and results in higher fuel consump- t...

  • Page 264

    More often if subject to a wide range of outdoor tempera- tures, as tire pressures vary with temperature changes. Inflation pressures specified on the label are always “cold inflation pressure.” cold inflation pressure is defined as the tire pressure after the vehicle has been idle for at least 3 ho...

  • Page 265

    Radial-ply tires warning! Combining radial ply tires with other types of tires on your vehicle will cause your vehicle to handle poorly. The instability could cause an accident. Al- ways use radial tires in sets of four. Never combine them with other types of tires. Cuts and punctures in radial tire...

  • Page 266

    Tread wear indicators these indicators are narrow strips 1/16 inch (1.6 mm) thick and are found in the tread pattern grooves. When the tread pattern is worn down to these treadwear indicators, the tires should be replaced. Overloading your vehicle, long trips in very hot weather, and driving on bad ...

  • Page 267

    Warning! • do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unap- proved tires and wheels may change suspension dimen- sions and performance characteristics, resulting in changes to steering, handling, and braking of your vehicle. This can caus...

  • Page 268

    Tires may also cause the vehicle to pull left or right. Alignment will not correct this problem. See your dealer for proper diagnosis of the problem. Improper alignment will not normally cause vehicle vibration, which may be a result of tire and wheel out-of-balance. Proper balancing will reduce vib...

  • Page 269

    The system will consist of tire pressure monitoring sensors attached to each wheel through the valve stem mounting hole, a central receiver module and an amber colored indicator lamp. A sensor is located in the spare wheel if the vehicle is equipped with a matching full size spare wheel and tire ass...

  • Page 270

    Caution! After inspecting or adjusting the tire pressure al- ways reinstall the valve stem cap. This will prevent moisture and dirt from entering the valve stem, which could damage the wheel rim sensor. Note: • the tpm system can inform the driver of a low tire pressure condition. • the tpm system i...

  • Page 271

    System fault is detected. The flash cycle will repeat every ten minutes or until the fault condition is removed and reset. The tire pressure monitoring system consists of the following components: • receiver module • 4/5 wheel sensors • 4 wheel sensor trigger modules • tire pressure monitoring syste...

  • Page 272

    Note: the indicator lamp will only illuminate for the four active road tires. A low spare tire pressure will not cause the indicator lamp to illuminate when the appropriate conditions exist, the electronic vehicle information center (evic) displays the following messages. Left front, left rear, righ...

  • Page 273

    Caution! After inspecting or adjusting the tire pressure al- ways reinstall the valve stem cap. This will prevent moisture and dirt from entering the valve stem, which could damage the wheel rim sensor. Note: • the tpm system can inform the driver of a low tire pressure condition. • the tpm system i...

  • Page 274

    Tire chains caution! To avoid damage to your vehicle or tires, observe the following precautions: • because of restricted chain clearance between tires and other suspension components, it is important that only chains in good condition are used. Broken chains can cause serious damage. Stop the vehic...

  • Page 275

    Tire rotation recommendations tires on the front and rear axles of vehicles operate at different loads and perform different steering, handling, and braking functions. For these reasons, they wear at unequal rates, and develop irregular wear patterns. These effects can be reduced by timely rotation ...

  • Page 276

    The suggested rotation method is the “forward-cross” shown in the following diagram. Fuel requirements (gasoline engines) your engine is designed to meet all emis- sions regulations and provide excellent fuel economy and performance when us- ing high quality unleaded gasoline having an octane rating...

  • Page 277

    Light spark knock at low engine speeds is not harmful to your engine. However, continued heavy spark knock at high speeds can cause damage and immediate service is required. Poor quality gasoline can cause problems such as hard starting, stalling and hesitations. If you experience these symptoms, tr...

  • Page 278

    Gasoline/oxygenate blends some fuel suppliers blend unleaded gasoline with oxy- genates such as 10% ethanol, mtbe, and etbe. Oxygen- ates are required in some areas of the country during the winter months to reduce carbon monoxide emissions. Fuels blended with these oxygenates may be used in your ve...

  • Page 279

    Materials added to fuel all gasoline sold in the united states is required to contain effective detergent additives. Use of additional detergents or other additives is not needed under normal conditions. Fuel system cautions caution! Follow these guidelines to maintain your vehicle’s performance: • ...

  • Page 280

    Carbon monoxide warnings warning! Carbon monoxide (co) in exhaust gases is deadly. Follow the precautions below to prevent carbon monoxide poisoning: • do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas which can kill. Never run the engine in a closed area, such ...

  • Page 281

    Note: daimlerchrysler corporation recommends that this vehicle should be operated using diesel fuel with 15 ppm sulfur or less, where it is available. Warning! Do not use alcohol or gasoline as a fuel blending agent. They can be unstable under certain conditions and hazardous or explosive when mixed...

  • Page 282

    The gas cap is located behind the fuel filler door, on the left side of the vehicle. If the gas cap is lost or damaged, be sure the replacement cap has been designed for use with this vehicle. When tightening the gas cap, tighten until 2 or 3 clicks are heard to insure that the cap is properly seate...

  • Page 283

    Loose fuel filler cap message if the vehicle diagnostic system determines that the fuel filler cap is loose, improperly installed, or damaged, a “check gas cap” message will be displayed in the evic (electronic vehicle information center). Refer to “overhead console” in section 3 of this manual. Tig...

  • Page 284

    Perform maintenance services as prescribed in the “maintenance schedules” section. When your vehicle is used for trailer towing, never exceed the gross axle weight rating (gawr) by the addition of: • the tongue weight of the trailer. • the weight of any other type of cargo or equipment put in or on ...

  • Page 285

    Caution! If the trailer weighs more than 1,000 lbs (454 kg) loaded, it should have its own brakes and they should be of adequate capacity. Failure to do this could lead to accelerated brake lining wear, higher brake pedal effort, and longer stopping distances. Warning! Connecting trailer brakes to y...

  • Page 286

    Minimum vehicle requirements for trailer towing 286 starting and operating.

  • Page 287

    Recreational towing (behind motorhome, etc.) towing – 2wd models recreational towing is not allowed. Towing with the rear wheels on the ground can result in severe transmis- sion damage. Towing — 4wd models caution! Internal damage to the transfer case will occur if a front or rear wheel lift is use...

  • Page 288

    5. Shift automatic transmission into d (drive) or manual transmission into any forward gear. 6. Release brake pedal and ensure that there is no vehicle movement. 7. Shut the engine off and place the ignition key into the unlocked off position. 8. Shift automatic transmission into p (park) or ensure ...

  • Page 289

    5. Start engine. 6. Shift automatic transmission into d (drive) or manual transmission into any forward gear. Warning! You or others could be injured if you leave the vehicle unattended with the transfer case in the n (neutral) position without first fully engaging the parking brake. The transfer ca...

  • Page 290

    Warning! Do not add a snow plow, winches, or any other aftermarket equipment to the front of your vehicle. This could adversely affect the functioning of the airbag system and you could be injured. 290 starting and operating.

  • Page 291: Contents

    What to do in emergencies contents 䡵 hazard warning flashers . . . . . . . . . . . . . . . . . 292 䡵 if your engine overheats . . . . . . . . . . . . . . . . . 293 䡵 jacking and tire changing . . . . . . . . . . . . . . . . 294 ▫ jack location . . . . . . . . . . . . . . . . . . . . . . . . 295 ▫ sp...

  • Page 292

    Hazard warning flashers your vehicle’s hazard warning flasher is an emergency warning system. When you activate it, all front and rear directional signals will flash intermittently. Use it when your vehicle is disabled on or near the road. It warns other drivers to steer clear of you and your vehicl...

  • Page 293

    If your engine overheats in any of the following situations, you can reduce the potential for overheating by taking the appropriate ac- tion. • on the highways — slow down. • in city traffic — while stopped, put transmission in n (neutral), but do not increase engine idle speed. Note: there are step...

  • Page 294

    If the coolant temperature of a vehicle equipped with a diesel engine approaches the “h” (hot mark) a warning chime will sound to alert the driver. The air conditioning system will turn off automatically and power loss will occur until the engine temperature returns to the normal range. If the overh...

  • Page 295

    Jack location the scissor-type jack, and tire changing tools are stored beneath the right rear seat. To remove the jack from its stowage position, turn the thumb screw counterclock- wise to loosen jack assembly and then remove it. Spare tire stowage to remove the spare tire from the carrier, remove ...

  • Page 296

    Note: if you have added aftermarket accessories to the spare tire mounted carrier, it cannot exceed a gross weight of 50 lbs (23 kg) including the weight of the spare tire. Preparations for jacking park the vehicle on a firm level surface, avoid ice or slippery areas, set the parking brake and place...

  • Page 297

    4. Locate the jack as shown. For the front tires, place it in the notch on the body weld seam behind wheel to be changed. For the rear tires, place it under the axle by the wheel to be changed. Position the jack handle on the jack. Do not raise the vehicle until you are sure the jack is fully engage...

  • Page 298

    Warning! Raising the vehicle higher than necessary can make the vehicle less stable and cause an accident. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. 6. Remove the lug nuts and wheel. 7. Position the spare wheel/tire on the vehicle and inst...

  • Page 299

    Jump starting procedure note: check the charge indicator on the battery. If the indicator is light or yellow, replace the battery. 1. Wear eye protection and remove any metal jewelry such as watch bands or bracelets that might make an unintended electrical contact. 2. When boost is provided by a bat...

  • Page 300

    Note: to start the vehicle following connection of a booster battery, the security alarm system must first be disabled by cycling a front door key cylinder or by using the keyless entry transmitter. Warning! Jump starting can be dangerous. To avoid personal injury or damage to electrical components ...

  • Page 301

    Warning! Do not attempt to push or tow your vehicle to get it started. Unburned fuel could enter the catalytic converter and, once the engine has started, ignite and damage the converter and vehicle. Emergency tow hooks — if equipped if your vehicle is equipped with tow hooks, they are mounted in th...

  • Page 302

    Towing a disabled vehicle 2wd models only provided the transmission is operable, tow only in n (neutral) at speeds not exceeding 30 mph (48 km/h), for distances of not more than 15 miles (24 km). Towing at more than 30 mph (48 km/h) or for more than 15 miles (24 km) can cause severe transmission dam...

  • Page 303: Maintaining Your Vehicle

    Maintaining your vehicle contents 䡵 2.4l engine . . . . . . . . . . . . . . . . . . . . . . . . . . . 306 䡵 3.7l engine . . . . . . . . . . . . . . . . . . . . . . . . . . . 307 䡵 2.8l turbo diesel engine . . . . . . . . . . . . . . . . . 308 䡵 onboard diagnostic system — obd ii . . . . . . . . 309 ...

  • Page 304

    ▫ maintenance-free battery . . . . . . . . . . . . . . . . 320 ▫ air conditioner maintenance . . . . . . . . . . . . . 321 ▫ power steering fluid check . . . . . . . . . . . . . . 322 ▫ driveline and steering component lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . 322 ▫ body lubric...

  • Page 305

    䡵 bulb replacement . . . . . . . . . . . . . . . . . . . . . . 351 ▫ head light . . . . . . . . . . . . . . . . . . . . . . . . . . 351 ▫ front turn signal . . . . . . . . . . . . . . . . . . . . . 352 ▫ front fog light (front fascia mounted) . . . . . 353 ▫ light bar . . . . . . . . . . . . . . . ....

  • Page 306

    2.4l engine 306 maintaining your vehicle.

  • Page 307

    3.7l engine maintaining your vehicle 307 7.

  • Page 308

    2.8l turbo diesel engine 308 maintaining your vehicle.

  • Page 309

    Onboard diagnostic system — obd ii your vehicle is equipped with a sophisticated onboard diagnostic system called obd ii. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide ex...

  • Page 310

    That the gas cap is properly tightened. Press the odometer reset button to turn the message off. If the problem persists, the message will appear the next time the vehicle is started. This might indicate a damaged cap. If the problem is detected twice in a row, the system will turn on the malfunctio...

  • Page 311

    5. Approximately 15 seconds later, one of two things will happen: a. The mil will flash for about 10 seconds and then return to being fully illuminated until you turn off the ignition key or start the engine. This means that your vehicle’s obd system is not ready and you should not proceed to the i/...

  • Page 312

    Dealer service your dealer has the qualified service personnel, special tools and equipment to perform all service operations in an expert manner. Service manuals are available which include detailed service information for your vehicle. Refer to these manuals before attempting any procedure yoursel...

  • Page 313

    The best time to check the engine oil level is about 5 minutes after a fully warmed engine has been shut off, or before starting the engine after it has sat overnight. Checking the oil while the vehicle is on level ground will improve the accuracy of the oil level readings. Maintain the oil level be...

  • Page 314

    If any of these apply to you, then change your engine oil at every interval shown in schedule “b” of the “mainte- nance schedules” section of this manual. If none of these apply to you, then change your engine oil at every interval shown on schedule “a” of the “main- tenance schedules” section of th...

  • Page 315

    Engine oil selection (diesel engines) for best performance and maximum protection for all engines under all types of operating conditions, the manufacturer recommends using synthetic engine oils that are api certified (sl/cf), and meet the require- ments of daimlerchrysler material standard ms-10725...

  • Page 316

    Disposing of used engine oil care should be taken in disposing of used engine oil from your vehicle. Used oil and oil filters, indiscriminately discarded, can present a problem to the environment. Contact your authorized dealer, service station, or gov- ernmental agency for advice on how and where u...

  • Page 317

    Spark plugs spark plugs must fire properly to assure engine perfor- mance and emission control. New plugs should be in- stalled at the mileage specified in the appropriate main- tenance chart. The entire set should be replaced if there is any malfunction due to a faulty spark plug. Refer to the “veh...

  • Page 318

    Warning! A hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your ex- haust system. Do not park or operate your vehicle in areas where your exhaust system can contact any- thing that can burn. In unusual sit...

  • Page 319

    Engine timing belt — 2.4l engine replace the engine timing belt at the intervals described in the appropriate maintenance schedule. Ignition wiring system — 2.4l engine replace the ignition cables at the intervals described in the appropriate maintenance schedule. Crankcase emission control system p...

  • Page 320

    Maintenance-free battery your vehicle is equipped with a maintenance-free battery. You will never have to add water, nor is periodic main- tenance required. Warning! Battery posts, terminals, and related accessories con- tain lead and lead compounds. Always wash hands after handling the battery. To ...

  • Page 321

    Caution! It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked (+) positive and negative (-) and identified on the battery case. Also, if a “fast charger” is ...

  • Page 322

    Refrigerant recovery and recycling r-134a air conditioning refrigerant is a hydrofluorocar- bon (hfc) that is endorsed by the environmental pro- tection agency and is an ozone-saving product. How- ever, the manufacturer recommends that air conditioning service be performed by dealers or other servic...

  • Page 323

    “maintenance schedule” in section 8 is very important, particularly if your vehicle is subjected to off-road or other heavy-duty use. See your authorized dealer for complete service information. Body lubrication locks and all body pivot points, including such items as seat tracks, doors, swing gate ...

  • Page 324

    Windshield washers the fluid reservoir for the windshield washers and the rear window washer is shared. It is located in the front of the engine compartment on the passenger side and should be checked for fluid level at regular intervals. Fill the reservoir with windshield washer solvent (not antifr...

  • Page 325

    Have an authorized technician inspect the complete ex- haust system and adjacent body areas for broken, dam- aged, deteriorated, or mispositioned parts. Open seams or loose connections could permit exhaust fumes to seep into the passenger compartment. In addition, inspect the exhaust system each tim...

  • Page 326

    Cooling system — drain, flush, and refill at the intervals shown on the appropriate “maintenance schedule” the system should be drained, flushed, and refilled. If the coolant solution is dirty or contains a considerable amount of sediment, clean and flush with a reliable cooling system cleaner (see ...

  • Page 327

    Adding engine coolant your vehicle has been built with an improved antifreeze/ coolant that allows extended maintenance intervals. This antifreeze/coolant can be used up to 5 years or 100,000 miles before replacement. To prevent reducing this ex- tended maintenance period, it is important that you u...

  • Page 328

    The cap should be inspected and cleaned if there is any accumulation of foreign material on the sealing surfaces. Warning! The warning words do not open hot on the cooling system pressure cap are a safety precaution. Never add antifreeze/coolant when the engine is overheated. Do not loosen or remove...

  • Page 329

    When additional antifreeze/coolant is needed to main- tain the proper level, it should be added to the coolant recovery bottle. Do not overfill. Points to remember note: when the vehicle is stopped after a few miles (kilometers) of operation, you may observe vapor coming from the front of the engine...

  • Page 330

    • make sure that the radiator and coolant recovery bottle hoses are not kinked or obstructed. • keep the front of the radiator clean. Also, if your vehicle is equipped with air conditioning, keep the front of the condenser clean. • do not change the thermostat for summer or winter operation. If repl...

  • Page 331

    Warning! Riding the brakes can lead to brake failure and possibly an accident. Driving with your foot resting or riding on the brake pedal can result in abnormally high brake temperatures, excessive lining wear, and possible brake damage. You wouldn’t have your full braking capacity in an emergency....

  • Page 332

    Warning! Worn brake hoses can burst and cause brake failure. You could have an accident. If you see any signs of cracking, scuffing, or worn spots, have the brake hoses replaced immediately. Brake master cylinder the fluid level in the master cylinder should be checked when performing under hood ser...

  • Page 333

    Use only manufacturer’s recommended brake fluid, refer to recommended fluids, lubricants, and genuine parts for correct fluid type. Warning! Use of a brake fluid that may have a lower initial boiling point or unidentified as to specification, may result in sudden brake failure during hard pro- longe...

  • Page 334

    Caution! Using a transmission fluid other than the manufac- turer’s recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder. Using a transmission fluid other than the manufacturer’s recommended fluid will result in more frequent fluid and filter change...

  • Page 335

    (cross-hatched area) on the oil level indicator. The fluid level indicator should be in the cold region at 70° f (21° c) fluid temperature. If the fluid level is low, add sufficient fluid to bring to the proper level. Refer to recommended fluids, lubricants and genuine parts for correct fluid type. ...

  • Page 336

    Frequency of fluid change under normal operating conditions, the fluid installed at the factory will give satisfactory lubrication for the life of the vehicle. Fluid changes are not necessary unless the lubricant has become contaminated with water. If con- taminated with water, the fluid should be c...

  • Page 337

    Caution! When installing plugs, do not overtighten. You could damage them and cause them to leak. Selection of lubricant use only manufacturer’s recommended fluid, refer to recommended fluids, lubricants, and genuine parts for correct fluid type. Front/rear axle fluid the front axle has a threaded “...

  • Page 338

    Hot or cold weather and other extreme conditions will have an adverse effect on paint, metal trim, and under- body protection. The following maintenance recommendations will enable you to obtain maximum benefit from the corrosion resistance built into your vehicle. What causes corrosion? Corrosion i...

  • Page 339

    Caution! Do not use abrasive or strong cleaning materials such as steel wool or scouring powder, which will scratch metal and painted surfaces. Special care • if you drive on salted or dusty roads or if you drive near the ocean, hose off the undercarriage at least once a month. • it is important tha...

  • Page 340

    • if a lot of driving is done on gravel roads, consider mud or stone shields behind each wheel. • use mopar威 touch up paint on scratches or chips as soon as possible. Your authorized dealer has touch up paint to match the color of your vehicle. Interior care use mopar 威 fabric cleaner to clean fabri...

  • Page 341

    Cleaning inside rear windows equipped with electric defrosters. Do not use scrapers or other sharp instru- ments which may scratch the elements. When cleaning the rear view mirror, spray cleaner on the towel or rag that you are using. Do not spray cleaner directly on the mirror. Carpet vacuum your c...

  • Page 342

    Vegetation or brush that could become a fire hazard, or conceal damage to fuel lines, brake hoses, axle pinion seals, and propeller shafts. Caution! Under frequent heavy-duty driving conditions, change all lubricants and lubricate body compo- nents, all driveline joints and steering linkage more oft...

  • Page 343

    Cavity fuse description 1 15 amp blue horn relay, power sunroof relay, power window relay 2 10 amp red rear fog lights (export only) 3 20 amp yel- low cigar lighter 4 10 amp red headlight low beam right 5 10 amp red headlight low beam left 6 20 amp yel- low body control module/power door locks 7 10 ...

  • Page 344

    Cavity fuse description 19 20 amp yel- low frt fog lights/trailer tow stop and turn lights 20 spare 21 10 amp red radio 22 20 amp yel- low power sunroof relay/ antenna module (export only) 23 spare 24 10 amp red pdc blower motor 25 10 amp red heated seat switches/hvac control head/trailer tow batter...

  • Page 345

    Cavity fuse description 38 10 amp red abs controller/shifter as- sembly 39 10 amp red hazard flasher (turn signals)/backup lamp switch (manual transmission only)/transmission range switch (automatic transmis- sion only) underhood fuses (power distribution center) your vehicle is equipped with an ele...

  • Page 346

    Cavity fuse description f3 50 amp red jb power f4 40 amp green abs pump f5 20 amp yel- low ngc trans f6 30 amp pink asd f7 50 amp red jb power f8 40 amp green ign/start f9 50 amp red jb power f10 30 amp pink trailer tow f11 open f12 30 amp pink light bar f13 40 amp green windows f14 40 amp green ign...

  • Page 347

    Cavity fuse description f27 open f28 15 amp blue starter r29 half iso re- lay fuel pump r30 half iso re- lay starter r31 half iso re- lay wiper on/off r32 half iso re- lay wiper hi/lo r33 full iso re- lay h. Blower r34 full iso re- lay rad. Fan hi r35 half iso re- lay a/c clutch r36 open cavity fuse...

  • Page 348

    Cavity fuse description f5 open f6 30 amp pink asd f7 50 amp red jb power f8 40 amp green ign/start f9 50 amp red jb power f10 30 amp pink trailer tow f11 20 amp yel- low fuel heater f12 30 amp pink light bar f13 40 amp green windows f14 40 amp green ignition switch f15 50 amp red jb power f16 15 am...

  • Page 349

    Cavity fuse description r30 half iso re- lay starter r31 half iso re- lay wiper on/off r32 half iso re- lay wiper hi/lo r33 full iso re- lay h. Blower r34 full iso re- lay rad. Fan hi r35 half iso re- lay a/c clutch r36 half iso re- lay viscous heat r37 open r38 open cavity fuse description r39 full...

  • Page 350

    Air conditioning system at idle for about five minutes in the fresh air and high blower setting. This will insure adequate system lubrication to minimize the possibility of compressor damage when the system is started again. Replacement bulbs interior lights bulb type a/c heater . . . . . . . . . . ...

  • Page 351

    Bulb replacement head light 1. Open the hood. 2. Reach behind the headlamp unit in the engine com- partment to access the headlamp bulb lock ring. 3. Firmly grasp the lock ring on the back of the headlamp unit housing. 4. Rotate the lock ring on the back of the headlamp housing counter-clockwise to ...

  • Page 352

    Front turn signal 1. Remove the screw from the turn signal/park lamp unit. 2. Pull the inboard side of the lamp away enough to disengage the tab that secures the outboard side of the lamp from the slot in the front bumper fascia. 3. Rotate the bulb socket counter-clockwise to unlock it. Caution! Do ...

  • Page 353

    Front fog light (front fascia mounted) 1. Remove the three screws from the backside of the lamp housing. 2. Pull the bezel and lens away from the lamp housing far enough to access and disconnect the wiring connector from the bulb pigtail wire. 3. Pinch together the two hooked ends of the bulb retain...

  • Page 354

    Light bar 1. Remove the screws from the light bar cover. 2. Remove the light bar cover. 3. Disconnect wiring harness from bulb socket. 4. Rotate the socket on the back of the lamp housing counter-clockwise to unlock it. Caution! Do not touch the new bulb with your fingers. Oil contamination will sev...

  • Page 355

    Rear tail, stop, turn signal, and back-up lights 1. Open the swing gate. 2. Remove the two torx fasteners. 3. Remove rear lamp assembly. 4. Rotate the socket on the back of the lamp housing counter-clockwise to unlock it. 5. Replace the bulb. Center high mounted stop light (chmsl) 1. Remove the two ...

  • Page 356

    Fluid capacities u.S. Metric fuel (approximate) 20.5 gallons 78 liters engine oil with filter 2.4/3.7 liter engines (sae 5w-30, api certified engine oil) 5 qts 4.7 liters 2.8 liter diesel engine (sae 0w-40 mobil 1 威 synthetic, api certified engine oil) 6.4 qts 6.1 liters cooling system * 2.4 liter e...

  • Page 357

    Recommended fluids, lubricants and genuine parts engine component fluid, lubricant, or genuine part engine coolant mopar 威 antifreeze/coolant 5 year/100,000 mile formula hoat (hybrid or- ganic additive technology) engine oil (2.4l and 3.7l engines) use api certified sae 5w-30 engine oil, meeting the...

  • Page 358

    Chassis component fluid, lubricant, or genuine part automatic transmission mopar 威 atf+4 automatic transmission fluid manual transmission mopar 威 manual transmission lubricant or equivalent (meeting the re- quirements of daimlerchrysler material standard ms-9224) transfer case mopar 威 atf+4 automati...

  • Page 359: Maintenance Schedules

    Maintenance schedules contents 䡵 emission control system maintenance . . . . . . . . 360 䡵 maintenance schedules — gasoline engines . . . . 360 ▫ schedule “b” — gasoline engines . . . . . . . . . 363 ▫ schedule “a” — gasoline engines . . . . . . . . . 373 䡵 maintenance schedules — diesel engines . ....

  • Page 360

    Emission control system maintenance the “scheduled” maintenance services, listed in bold type must be done at the times or mileages specified to assure the continued proper functioning of the emission control system. These, and all other maintenance services included in this manual, should be done t...

  • Page 361

    • taxi, police, or delivery service (commercial service). • off-road or desert driving. • if equipped for and operated with e-85 (ethanol) fuel. Note: if any of these apply to you then change your engine oil every 3,000 miles (5 000 km) or 3 months, whichever comes first and follow “schedule b” of t...

  • Page 362

    At each stop for fuel • check the engine oil level about 5 minutes after a fully warmed engine is shut off. Checking the oil level while the vehicle is on level ground will improve the accu- racy of the oil level reading. Add oil only when the level is at or below the add or min mark. • check the wi...

  • Page 363

    Schedule “b” — gasoline engines follow schedule “b” if you usually operate your vehicle under one or more of the following conditions. • day or night temperatures are below 32°f (0°c). • stop and go driving. • extensive engine idling. • driving in dusty conditions. • short trips of less than 10 mile...

  • Page 364

    Miles 3,000 6,000 9,000 12,000 15,000 (kilometers) (5 000) (10 000) (14 000) (19 000) (24 000) change the engine oil and engine oil filter, if not replaced at 3 months. X x x x x rotate the tires. X x inspect the engine air filter element, replace if necessary. X inspect the brake linings. X drain a...

  • Page 365

    Miles 18,000 21,000 24,000 27,000 30,000 (kilometers) (29 000) (34 000) (38 000) (43 000) (48 000) change the engine oil and engine oil filter, if not replaced at 3 months. X x x x x rotate the tires. X x x inspect the engine air filter element, replace if necessary. X replace the spark plugs. X ins...

  • Page 366

    Miles 33,000 36,000 39,000 42,000 45,000 (kilometers) (53 000) (58 000) (62 000) (67 000) (72 000) change the engine oil and engine oil filter, if not replaced at 3 months. X x x x x rotate the tires. X x inspect the engine air filter element, replace if necessary. X inspect the brake linings. X dra...

  • Page 367

    Miles 48,000 51,000 54,000 57,000 60,000 (kilometers) (77 000) (82 000) (86 000) (91 000) (96 000) change the engine oil and engine oil filter, if not replaced at 3 months. X x x x x rotate the tires. X x x inspect the engine air filter element, replace if necessary. X replace the spark plugs. X ins...

  • Page 368

    Miles 63,000 66,000 69,000 72,000 75,000 (kilometers) (101 000) (106 000) (110 000) (115 000) (120 000) change the engine oil and engine oil filter, if not replaced at 3 months. X x x x x rotate the tires. X x inspect the engine air filter element, replace if necessary. X inspect the brake linings. ...

  • Page 369

    Miles 78,000 81,000 84,000 87,000 90,000 (kilometers) (125 000) (130 000) (134 000) (139 000) (144 000) change the engine oil and engine oil filter, if not replaced at 3 months. X x x x x rotate the tires. X x x inspect the engine air filter element, replace if necessary. X replace the spark plugs. ...

  • Page 370

    Miles 93,000 96,000 99,000 102,000 105,000 (kilometers) (149 000) (154 000) (158 000) (163 000) (168 000) change the engine oil and engine oil filter, if not replaced at 3 months. X x x x x rotate the tires. X x inspect the engine air filter element, replace if necessary. X inspect the brake linings...

  • Page 371

    Miles 108,000 111,000 114,000 117,000 120,000 (kilometers) (173 000) (178 000) (182 000) (187 000) (192 000) change the engine oil and engine oil filter, if not replaced at 3 months. X x x x x rotate the tires. X x x inspect the engine air filter element, replace if necessary. X replace the spark pl...

  • Page 372

    Miles 108,000 111,000 114,000 117,000 120,000 (kilometers) (173 000) (178 000) (182 000) (187 000) (192 000) inspect the drive belt and replace as needed. Not required if belt was previously replaced. X drain and refill the transfer case fluid. X flush and replace the engine coolant/anti-freeze at 1...

  • Page 373

    Schedule “a” — gasoline engines miles 6,000 12,000 18,000 24,000 30,000 (kilometers) (10 000) (19 000) (29 000) (38 000) (48 000) [months] [6] [12] [18] [24] [30] change the engine oil and engine oil filter. X x x x x rotate the tires. X x x x x inspect the engine air filter element, and replace if ...

  • Page 374

    Miles 36,000 42,000 48,000 54,000 (kilometers) (58 000) (67 000) (77 000) (86 000) [months] [36] [42] [48] [54] change the engine oil and engine oil filter. X x x x rotate the tires. X x x x inspect the brake linings. X x 374 schedule “a” — gasoline engines 8 m a i n t e n a n c e s c h e d u l e s.

  • Page 375

    Miles 60,000 66,000 72,000 78,000 (kilometers) (96 000) (106 000) (115 000) (125 000) [months] [60] [66] [72] [78] change the engine oil and engine oil filter. X x x x rotate the tires. X x x x inspect the engine air filter element, and replace if nec- essary. X replace the spark plugs. X inspect th...

  • Page 376

    Miles 84,000 90,000 96,000 102,000 (kilometers) (134 000) (144 000) (154 000) (163 000) [months] [84] [90] [96] [102] change the engine oil and engine oil filter. X x x x rotate the tires. X x x x inspect the engine air filter element, and replace if nec- essary. X replace the spark plugs. X inspect...

  • Page 377

    Miles 108,000 114,000 120,000 (kilometers) (173 000) (182 000) (192 000) [months] [108] [114] [120] change the engine oil and engine oil filter. X x x rotate the tires. X x x inspect the engine air filter element, and replace if necessary. X replace the spark plugs. X inspect and replace the pcv val...

  • Page 378

    Maintenance schedules — diesel engines there are two maintenance schedules that show the required service for your vehicle. First is schedule ⴖbⴖ. It is for vehicles that are operated under the conditions that are listed below and at the beginning of the schedule. • day or night temperatures are bel...

  • Page 379

    At each stop for fuel • check the engine oil level about 5 minutes after a fully warmed engine is shut off. Checking the oil level while the vehicle is on level ground will improve the accu- racy of the oil level reading. Add oil only when the level is at or below the add or min mark. • check the wi...

  • Page 380

    Schedule “b” — diesel engines follow schedule “b” if you usually operate your vehicle under one or more of the following conditions. • day or night temperatures are below 32°f (0°c). • stop and go driving. • extensive engine idling. • driving in dusty conditions. • short trips of less than 10 miles ...

  • Page 381

    Miles 6,250 12,500 18,750 25,000 31,250 (kilometers) (10 000) (20 000) (30 000) (40 000) (50 000) change the engine oil and engine oil filter. X x x x x inspect the engine air filter element. Replace as necessary. X x x x x replace the engine air filter element. X x inspect the boost pressure soleno...

  • Page 382

    Miles 37,500 43,750 50,000 56,250 62,500 (kilometers) (60 000) (70 000) (80 000) (90 000) (100 000) change the engine oil and engine oil filter. X x x x x inspect the engine air filter element. Replace as necessary. X x x x x replace the engine air filter element. X x x inspect the boost pressure so...

  • Page 383

    Miles 68,750 75,000 81,250 87,500 93,750 100,000 (kilometers) (110 000) (120 000) (130 000) (140 000) (150 000) (160 000) change the engine oil and engine oil filter. X x x x x x inspect the engine air filter element. Re- place as necessary. X x x x x x replace the engine air filter element. X x x i...

  • Page 384

    Miles 68,750 75,000 81,250 87,500 93,750 100,000 (kilometers) (110 000) (120 000) (130 000) (140 000) (150 000) (160 000) inspect the brake linings. X x drain and refill the front and rear axle fluid. X x 〫 applies only if vehicle is used for frequent trailer towing, or fleet/commercial service. † t...

  • Page 385

    Schedule “a” — diesel engines miles 12,500 25,000 37,500 50,000 (kilometers) (20 000) (40 000) (60 000) (80 000) change the engine oil and engine oil filter. X x x x inspect the engine air filter element. Replace as neces- sary. X x x x replace the engine air filter element. X x inspect the boost pr...

  • Page 386

    Miles 62,500 75,000 87,500 100,000 (kilometers) (100 000) (120 000) (140 000) (160 000) change the engine oil and engine oil filter. X x x x inspect the engine air filter element. Replace as neces- sary. X x x x replace the engine air filter element. X x inspect the boost pressure solenoid filter. R...

  • Page 387

    Miles 62,500 75,000 87,500 100,000 (kilometers) (100 000) (120 000) (140 000) (160 000) replace the engine accessory drive belt. X inspect the brake linings. X x inspect the transfer case fluid. X † the replacement of such component is requested if there is superficial wear, bearing clearance, or ev...

  • Page 389: Contents

    If you need consumer assistance contents 䡵 suggestions for obtaining service for your vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 390 ▫ prepare for the appointment . . . . . . . . . . . . 390 ▫ prepare a list . . . . . . . . . . . . . . . . . . . . . . . . 390 ▫ be reasonable...

  • Page 390

    Suggestions for obtaining service for your vehicle prepare for the appointment if you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty, discuss additional charges with the service manager. ...

  • Page 391

    Technicians, special tools, and the latest information to assure your vehicle is fixed correctly and in a timely manner. This is why you should always talk to your dealer’s service manager first. Most matters can be resolved with this process. • if for some reason you are still not satisfied, talk t...

  • Page 392

    Customer assistance for the hearing or speech impaired (tdd/tty) to assist customers who have hearing difficulties, the manufacturer has installed special tdd (telecommuni- cation devices for the deaf) equipment at its customer center. Any hearing or speech impaired customer who has access to a tdd ...

  • Page 393

    Warranty information see your manufacturer’s warranty information booklet for information on warranty coverage and transfer of warranty. If you need consumer assistance 393 9.

  • Page 394

    U.S. Only 394 if you need consumer assistance.

  • Page 395

    Mopar 姞 parts mopar 威 fluids, lubricants, parts, and accessories are available from your dealer. They will help you keep your vehicle operating at its best. Reporting safety defects in the 50 united states and washington d.C.: if you believe that your vehicle has a defect which could cause a crash o...

  • Page 396

    Publication order forms to order the following manuals, you may use either the website or the phone numbers listed below. Visa, mas- tercard, american express, and discover orders are ac- cepted. If you prefer mailing your payment, please call for an order form. Note: a street address is required wh...

  • Page 397

    Call toll free at: • 1–800–890–4038 (u.S.) • 1–800–387–1143 (canada) or visit us on the world wide web at: • www.Techauthority.Daimlerchrysler.Com • www.Daimlerchrysler.Ca/manuals if you need consumer assistance 397 9.

  • Page 399: Index

    Index 10

  • Page 400

    Abs (anti-lock brake) system . . . . . . . . . . . . 170,247 adding washer fluid . . . . . . . . . . . . . . . . . . . . . 157 air cleaner, engine (engine air cleaner filter) . . . 319 air conditioner maintenance . . . . . . . . . . . . . . . 321 air conditioning, operating tips . . . . . . . . . . ...

  • Page 401

    Bar, light . . . . . . . . . . . . . . . . . . . . . . . . . . 121,354 battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 320 emergency starting . . . . . . . . . . . . . . . . . . . . . 299 keyless transmitter replacement . . . . . . . . . . . . 29 saving feature (protection) . ....

  • Page 402

    Caution, exhaust gas . . . . . . . . . . . . . . . . . . . 73,141 cd changer . . . . . . . . . . . . . . . . . . . . . . . . 187,193 cd player . . . . . . . . . . . . . . . . . . 184,189,191,195,198 cd player maintenance . . . . . . . . . . . . . . . . . . . 211 cellular phone . . . . . . . . . . . ...

  • Page 403

    Selection of coolant . . . . . . . . . . . . . . . . . . 326,356 temperature gauge . . . . . . . . . . . . . . . . . . . . . 171 crankcase emission control system . . . . . . . . . . 319 cruise control (speed control) . . . . . . . . . . . . . . 127 cruise light . . . . . . . . . . . . . . . . . . ....

  • Page 404

    Electronic throttle control warning light . . . . . . 175 electronic vehicle information center . . . . . . . . . 131 emergency, in case of freeing vehicle when stuck . . . . . . . . . . . . . . . 236 hazard warning flasher . . . . . . . . . . . . . . . . . 292 jacking . . . . . . . . . . . . . . . ...

  • Page 405

    Exhaust gas caution . . . . . . . . . . . . . . . . . . . 73,280 exhaust system . . . . . . . . . . . . . . . . . . . . . . . . . 324 exterior finish care . . . . . . . . . . . . . . . . . . . . . . 338 filters air cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . 319 engine oil . . . . . ...

  • Page 406

    Requirements . . . . . . . . . . . . . . . . . . . 276,280,356 tank capacity . . . . . . . . . . . . . . . . . . . . . . . . 356 fuel system caution . . . . . . . . . . . . . . . . . . . 279,283 fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 342 garage door opener . . . . . . ...

  • Page 407

    Identifying your engine . . . . . . . . . . . . . . . . 306,307 ignition key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 wiring system . . . . . . . . . . . . . . . . . . . . . . . . 319 illuminated entry . . . . . . . . . . . . . . . . . . . . . . . . 19 inflation pressure ...

  • Page 408

    Anti-lock . . . . . . . . . . . . . . . . . . . . . . . . . . . 170 back-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 355 battery saver . . . . . . . . . . . . . . . . . . . . . . . . . 120 brake warning . . . . . . . . . . . . . . . . . . . . . . . . 173 bulb replacement . . . . . ....

  • Page 409

    Transmission warning . . . . . . . . . . . . . . . . . . . 172 turn signal . . . . . . . . . . . . . . . . . . 119,168,352,355 warning (instrument cluster description) . . . . . 168 loading vehicle tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 258 locks automatic door . . . . ....

  • Page 410

    Heated . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84 outside . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82 rearview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 vanity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84 modifications/alt...

  • Page 411

    Owner’s manual . . . . . . . . . . . . . . . . . . . . . . . . 396 paint care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 337 paint damage . . . . . . . . . . . . . . . . . . . . . . . . . . 337 panic alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 parking brake . . . ...

  • Page 412

    Rear wiper/washer . . . . . . . . . . . . . . . . . . . . . . 156 rearview mirrors . . . . . . . . . . . . . . . . . . . . . . . . 81 reclining front seats . . . . . . . . . . . . . . . . . . . . . 109 recommended fluids, lubricants and genuine parts . . . . . . . . . . . . . . . . . . . . . . . . ....

  • Page 413

    Seat belts adjustable upper shoulder anchorage . . . . . . . . 43 and pregnant women . . . . . . . . . . . . . . . . . . . 47 child restraint . . . . . . . . . . . . . . . . . . . . . . . 63,70 extender . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 inspection . . . . . . . . . . . . ....

  • Page 414

    Snow plow . . . . . . . . . . . . . . . . . . . . . . . . . . . . 289 spare tire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 295 spark plugs . . . . . . . . . . . . . . . . . . . . . . . . . . . . 317 specifications fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2...

  • Page 415

    Timing belt . . . . . . . . . . . . . . . . . . . . . . . . . . . . 319 tire and loading information placard . . . . . . 258,259 tire identification number (tin) . . . . . . . . . . . . . 257 tire markings . . . . . . . . . . . . . . . . . . . . . . . . . . 254 tire safety information . . . . . . . ...

  • Page 416

    Maintenance . . . . . . . . . . . . . . . . . . . . . . . 333,335 manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 227 shifting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 227 warning light . . . . . . . . . . . . . . . . . . . . . . . . 172 transmitter battery service ...

  • Page 417

    Wind buffeting . . . . . . . . . . . . . . . . . . . . . . . . . . 36 window fogging . . . . . . . . . . . . . . . . . . . . . . . . 214 windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 windshield washers . ...

  • Page 418: Notes

    Notes.

  • Page 419: Notes

    Notes.

  • Page 420: Notes

    Notes.

  • Page 421: Notes

    Notes.

  • Page 422: Notes

    Notes.

  • Page 423: Notes

    Notes.

  • Page 424: Notes

    Notes.