1. DL manuals
  2. Jeep
  3. Automobile
  4. 2005 Wrangler
  5. Owner's Manual

Jeep 2005 Wrangler Owner's Manual

Summary of 2005 Wrangler

  • Page 1

    Table of contents section page 1 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 things to know before starting your vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 3 understanding the fea...

  • Page 3: Introduction

    Introduction contents 䡵 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 ▫ roll over warning . . . . . . . . . . . . . . . . . . . . . 4 䡵 how to use this manual . . . . . . . . . . . . . . . . . . 7 䡵 warnings and cautions . . . . . . . . . . . . . . . . . . . 7 䡵 vehicle identi...

  • Page 4

    Introduction thank you for selecting a jeep 威 wrangler and welcome to our worldwide family. This is a specialized utility vehicle designed for both on-road and off-road use. It can go places and perform tasks for which conventional two-wheel drive enclosed vehicles were not intended. It handles and ...

  • Page 5

    Do not attempt sharp turns or abrupt maneuvers or other unsafe driving actions that can cause loss of vehicle control. Failure to operate this vehicle safely may result in an accident, roll over of the vehicle and serious injury or death. Because of its open-body construction, your vehicle offers le...

  • Page 6

    Operating this vehicle at excessive speeds or while intoxicated may result in loss of control, collision with other vehicles or objects, going off the road, or overturn- ing, any of which may lead to serious injury or death. Also, failure to use standard seat belts subjects the driver and passengers...

  • Page 7

    Warning! Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the state of california to cause cancer and birth defects or other reproductive harm. In addition, certain fluids contained in vehicles and certain prod- ucts of component wear contai...

  • Page 8

    Vehicle identification number the vehicle identification number (vin) is found on a stamped plate located on the left front corner of the instrument panel pad, visible from outside of vehicle through windshield. This number also appears on the automobile information disclosure label affixed to a win...

  • Page 9

    Vehicle modifications / alterations warning! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death. Introduction 9 1.

  • Page 11: Contents

    Things to know before starting your vehicle contents 䡵 a word about your keys . . . . . . . . . . . . . . . . . .13 ▫ ignition key . . . . . . . . . . . . . . . . . . . . . . . . . .13 ▫ key-in-ignition reminder . . . . . . . . . . . . . . . .14 䡵 sentry key immobilizer system — if equipped . .14 ▫ ...

  • Page 12

    ▫ seat belt extender . . . . . . . . . . . . . . . . . . . . . .26 ▫ driver and front passenger supplemental restraint systems (srs) — airbags . . . . . . . . . .27 ▫ child restraint . . . . . . . . . . . . . . . . . . . . . . . .34 䡵 engine break-in recommendations . . . . . . . . . . .44 䡵 safety ...

  • Page 13

    A word about your keys the keys for your new vehicle are enclosed in a plastic bag with the key code number on it. If you received your keys without the bag, ask your dealer to give you the number. The key code can also be obtained by the dealer from your vehicle invoice. Ignition key insert the key...

  • Page 14

    To remove the ignition key on models with a manual transmission, depress and hold the key release button, turn the ignition key to lock, and remove the key. Key-in-ignition reminder opening the driver’s door when the key is in the ignition, sounds a signal to remind you to remove the key. Caution! A...

  • Page 15

    Keys that have been programmed to the vehicle can be used to start and operate the vehicle for longer than the 2 second validation time period. The sentry key immobilizer system does not need to be armed or activated. Operation of the system is automatic regardless of whether or not the vehicle is l...

  • Page 16

    Important note about service a four digit pin number is needed to service the sentry key immobilizer system. This number can be obtained from your authorized dealer. However, this number can also be found on your customer invoice that you were given upon receipt of your vehicle. Replacement keys not...

  • Page 17

    Will sound and the skis indicator light will begin to flash. Turn the ignition switch off and remove the second key. 4. Insert a blank sentry key into the ignition switch and turn the ignition switch on within 60 seconds. After 10 seconds, a single chime will sound. The skis indicator light will sto...

  • Page 18

    To manually lock the steering wheel with the engine running, rotate the steering wheel 1/2 revolution from straight ahead position, turn off the engine and remove the key. Rotate the steering wheel slightly in both directions until the lock engages. To release the steering wheel lock insert the key ...

  • Page 19

    Warning! • for personal security reasons and safety in an accident, lock the vehicle doors when you drive as well as when you park and leave the vehicle. • when leaving the vehicle always remove the key from the ignition lock, and lock your vehicle. Do not leave children unattended in the vehicle, o...

  • Page 20

    You will be carrying children too small for adult-size belts, your seat belts can also be used to hold infant and child restraint systems. Please pay close attention to the information in this section. It tells you how to use your restraint system properly to keep you and your passengers as safe as ...

  • Page 21

    Normal conditions. But in a collision, the belt will lock and reduce the risk of your striking the inside of the vehicle or being thrown out. Warning! • it is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to ...

  • Page 22

    Lap/shoulder belt operating instructions 1. Enter the vehicle and close the door. Sit back and adjust the seat. 2. The seat belt latch plate is above the back of the front seat, next to your arm in the rear seat. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as fa...

  • Page 23

    Warning! • a belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal inju- ries. Always buckle your belt into the buckle nearest you. • a belt that is loose will not protect you as well. In a sudden stop yo...

  • Page 24

    Warning! • a lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as possible and keep it snug. • a twisted belt cannot do its job as well. In a collision ...

  • Page 25

    Warning! A frayed or torn belt could rip apart in a collision and leave you with no protection. Inspect the belt system periodically, checking for cuts, frays, or loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Seat belt assemblies must be replaced a...

  • Page 26

    Seat belts and pregnant women we recommend that pregnant women use seat belts throughout their pregnancy. Keeping the mother safe is the best way to keep the baby safe. Pregnant women should wear the lap part of the belt across the thighs and as snug across the hips as possible. Keep the belt low so...

  • Page 27

    Driver and front passenger supplemental restraint systems (srs) — airbags this vehicle has front airbags for both the driver and front passenger as a supplement to the seat belt restraint system. The driver’s front airbag is mounted in the center of the steering wheel. The passenger’s front airbag i...

  • Page 28

    Airbags inflate in moderate to high speed impacts. Along with the seat belts, front airbags work with the instru- ment panel knee bolsters to provide improved protection for the driver and front passenger. The seat belts are designed to protect you in many types of collisions. The front airbags depl...

  • Page 29

    You should read the instructions provided with your child restraint to make sure that you are using it properly. 2. All occupants should use their lap and shoulder belts properly. 3. The driver and front passenger seats should be moved back as far as practical to allow the front airbags room to infl...

  • Page 30

    • driver airbag • passenger airbag • steering wheel and column • instrument panel • crash sensor • interconnecting wiring • knee impact bolsters how the airbag system works • the airbag control module (acm) determines if a frontal collision is severe enough to require the airbags to inflate. • the a...

  • Page 31

    Warning! Ignoring the “airbag warning light” in your instru- ment panel could mean you won’t have the airbags to protect you in a collision. If the light does not come on, stays on after you start the vehicle, or if it comes on as you drive, have the airbag system checked right away. • the driver an...

  • Page 32

    If you do have a collision which deploys the airbags, any or all of the following may occur: • the nylon airbag material may sometimes cause abra- sions and/or skin reddening to the driver and front passenger as the airbags deploy and unfold. The abrasions are similar to friction rope burns or those...

  • Page 33

    Maintaining your airbag system warning! • modifications to any part of the airbag system could cause it to fail when you need it. You could be injured because the airbags are not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the stee...

  • Page 34

    Child restraint everyone in your vehicle needs to be buckled up all the time-babies and children, too. Every state in the united states and all canadian provinces require that small children ride in proper restraint systems. This is the law, and you can be prosecuted for ignoring it. Children 12 yea...

  • Page 35

    • the rearward-facing infant carrier is for babies weigh- ing up to about 20 lbs (9 kg), and one year old or more. The infant restraint must never be used in the front seat of a vehicle with a front passenger airbag unless the airbag is turned off. An airbag deployment could cause severe injury or d...

  • Page 36

    Warning! • improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the manufacturer’s directions ex- actly when installing an infant or child restraint. • a rearward facing infant restraint shou...

  • Page 37

    Portion of the lap/shoulder belt, or on the free end of the lap belt to tighten the belt. The cinching latch plate will keep the belt tight, however, any seat belt system will loosen with time, so check the belt occasionally and pull it tight if necessary. • in the rear seat, you may have trouble ti...

  • Page 38

    Introduced over a period of years, child restraint systems having attachments for those anchorages will continue to also have features for installation using the vehicle’s seat belts. Child restraints having tether straps and hooks for connection to the top tether anchorages have been avail- able fo...

  • Page 39

    In addition, there are tether strap anchorages behind the rear seat (on the floor behind each rear outboard seating position). Rear seat latch anchors rear seat tether anchor things to know before starting your vehicle 39 2.

  • Page 40

    Many, but not all restraint systems will be equipped with separate straps on each side, with each having a hook or connector for attachment to the lower anchorage and a means of adjusting the tension in the strap. Forward- facing toddler restraints and some rear-facing infant restraints will also be...

  • Page 41

    Installing child restraints using the vehicle seat belt the passenger seat belts are equipped with cinching latch plates, which are designed to keep the lap portion tight around the child restraint so that it is not necessary to use a locking clip. Pull up on the shoulder portion of the lap/shoulder...

  • Page 42

    To attach a child restraint tether strap: for the rear outboard seating positions, route the tether over the rear seat and attach to the rear floor tether anchors. If the add-a-trunk™ option is present in the vehicle, the lid should be opened and positioned against the back of the rear seat prior to...

  • Page 43

    Warning! An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchor positions directly behind the child seat to secure a child restraint top tether strap. Children too large for booster seats children who are large enough to wear th...

  • Page 44

    Engine break-in recommendations a long break-in period is not required for the engine in your new vehicle. Drive moderately during the first 300 miles (500 km). After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable. While cruising, brief full-throttle accelerat...

  • Page 45

    Garage, and never sit in a parked vehicle with the engine running for a extended period. If the vehicle is stopped in an open area with engine running for more than a short period, adjust the ventilation system to force fresh, outside air into the vehicle. • guard against carbon monoxide with proper...

  • Page 46

    Have it serviced. If the light stays on or comes on while driving, have the system checked by an authorized dealer. Defrosters check operation by selecting the defrost mode and place the blower control on high speed. You should feel the air directed against the windshield. Safety checks you should m...

  • Page 47: Contents

    Understanding the features of your vehicle contents 䡵 mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50 ▫ inside day/night mirror . . . . . . . . . . . . . . . . .50 ▫ inside automatic dimming compass/temperature mirror — if equipped . . . . . . . . . . . . . . . . . . . .50 ▫ ...

  • Page 48

    ▫ parking lights, instrument panel lights, and headlights . . . . . . . . . . . . . . . . . . . . . . . . . . .62 ▫ lights-on reminder . . . . . . . . . . . . . . . . . . . .63 ▫ headlight dimmer switch . . . . . . . . . . . . . . . .63 ▫ passing light . . . . . . . . . . . . . . . . . . . . . . . ....

  • Page 49

    ▫ console storage compartment — if equipped . .72 ▫ add-a-trunk™ — if equipped . . . . . . . . . . . .72 䡵 dual top — if equipped . . . . . . . . . . . . . . . . . .73 ▫ removing the soft top . . . . . . . . . . . . . . . . . .73 ▫ installing the soft top . . . . . . . . . . . . . . . . . .75 䡵 hard...

  • Page 50

    Mirrors inside day/night mirror the mirror should be adjusted to center on the view through the rear window. A two-point pivot system allows for horizontal and vertical adjustment of the mirror. Annoying headlight glare can be reduced by moving the small control under the mirror to the night positio...

  • Page 51

    Caution! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror. Apply the solution onto a clean cloth and wipe the mirror clean. The compass/temperature display provides the outside temperature and one of eight compass headings (n, ne, e, se, s, sw...

  • Page 52

    Compass calibration automatic calibration once calibrated, the compass has the ability to self- correct for changes in magnetic field to keep the compass accurate. This is referred to as automatic calibration. If magnetic field changes are too great, the compass will enter cal mode on it’s own and m...

  • Page 53

    Compass variation adjustment compass variance is the difference between magnetic north and geographic north. In some areas of the country, the difference between magnetic and geographic north is great enough to cause the compass to give false readings. If this occurs, the compass variance must be se...

  • Page 54

    To set the variance: turn the ignition on, and press and hold the center button for 3 to 6 seconds. The last variance zone number will be displayed. Each press of the center button will select a new variance zone. When the proper zone is selected, wait 5 seconds to resume normal operation. Outside m...

  • Page 55

    Warning! • vehicles and other objects seen in the right side convex mirror will look smaller and farther away than they really are. Relying too much on your right side mirror could cause you to collide with another vehicle or other object. • use your inside mirror when judging the size or distance o...

  • Page 56

    Front seat adjustment — recline to adjust seatback, lift lever, lean back, and release lever at desired position. To return seatback, lift the lever, lean forward and release the lever. Warning! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest....

  • Page 57

    Tilting front seats push the lever upward on the seatback to tilt the entire seat forward. Fold and tumble rear seat to expand the cargo area: 1. Slide seat belts through the seat cushions into the cargo area. 2. Lift the seatback release lever and fold seatback for- ward. Front seat tilt lever rear...

  • Page 58

    3. Slowly flip the entire seat forward. 4. When completed, return seat to it’s normal position. Removing the rear seat warning! • it is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision people riding in these areas are more likely to be seri- ously injured o...

  • Page 59

    • press down on release bar on each side, and pull seat out and away from lower bracket. • remove seat from the vehicle. Replacing the rear seat reverse steps for removing the seat. Be certain to pull the seat belts between the seat cushion and seatback. Position them for passenger use. Warning! • t...

  • Page 60

    To open and close the hood to open hood, first release both hood latches. Next, locate handle in middle of the front end of the hood. Insert hand into gap between hood and radiator support and lift up on handle to raise hood. You may have to push down slightly on hood before lifting up on handle. In...

  • Page 61

    To close the hood, remove the support rod from the radiator support and place it in the retaining clip. Lower the hood slowly, then let it drop the last few inches. Secure both of the hood latches. Warning! If the hood is not fully latched, it could fly up when the vehicle is moving and block your f...

  • Page 62

    Multi-function control lever the multi-function control lever controls the operation of the parking lights, headlights, headlight beam selection, passing light, fog lights, instrument panel light dimming, and turn signals. Parking lights, instrument panel lights, and headlights turn the end of the m...

  • Page 63

    Note: if the driver’s door is left open, and the head- lights or parking lights are left on, the “high beam indicator light” will flash and a chime will sound. Lights-on reminder if the headlights or parking lights are on after the ignition is turned off, a chime will sound when the driver’s door is...

  • Page 64

    Bulb. If an indicator fails to light when the lever is moved, it would suggest that the fuse or indicator bulb is defective. Note: a tone will chime if the turn signals are left on for more than 1 mile (2 km). Daytime running lights — canada only the headlights come on at a low intensity level after...

  • Page 65

    Windshield wiper operation move the lever upward to the second detent for lo speed wiper operation, or to the third detent for hi speed operation windshield washers to use the washer, pull the lever toward you and hold while spray is desired. If the lever is pulled while in the delay range, the wipe...

  • Page 66

    Tilt steering column to tilt the column, push down on the lever below the turn signal control and move the wheel up or down, as desired. Pull the lever back upwards to lock the column firmly in place. Warning! Tilting the steering column while the vehicle is moving is dangerous. Without a stable ste...

  • Page 67

    To activate press and release the on·off button to turn the system on. To turn the system off, press the on·off button again. The system should be turned off when not in use. The cruise indicator light in the instrument cluster illuminates when the system is on. To set at a desired speed when the ve...

  • Page 68

    To vary the speed setting when the speed control is on and set, speed can be increased by pressing and holding the resume/accel button. When the button is released, a new set speed will be established. Tapping the resume/accel button once will result in a 2 mph (3 km/h) speed increase. Each time the...

  • Page 69

    Electrical power outlet to the right of the cigar lighter (if equipped) is the 12 volt power outlet. The outlet is connected directly to the battery, items plugged into this outlet may discharge the battery and/or prevent engine starting. The outlet in- cludes a tethered cap labeled with a battery s...

  • Page 70

    Electrical outlet use with engine off warning! • many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.E. Cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge suffi- ciently to degrade battery life and/or...

  • Page 71

    The rear passengers have cup holders at the rear of the center console. Storage glove compartment to open the glove compartment, pull the latch up. Rear cup holders glove compartment understanding the features of your vehicle 71 3.

  • Page 72

    Console storage compartment — if equipped to unlock, insert key and turn. To open, press the latch button. Add-a-trunk™ — if equipped the factory-installed add-a-trunk™ option provides a secured compartment for parcels or equipment when the tailgate is closed and locked. To gain access to this compa...

  • Page 73

    Dual top — if equipped if your vehicle is equipped with a dual top, you must remove one of the tops from the vehicle. The soft top was installed at the factory for shipping purposes only. The soft top and the hard top are to be used indepen- dently. Removal is mandatory to prevent any possible wear ...

  • Page 74

    4. Using a rubber mallet, carefully tap the knuckles from the outside edge. This will disconnect the bow assembly from the pivot bracket. Remove the soft top from the vehicle and store in a clean, dry location. 5. Unzip the zipper on the sport bar cover to expose the pivot bracket. Remove the bracke...

  • Page 75

    6. Reinstall the hard top. Refer to “hard top installation” in this section. Installing the soft top note: the following procedures are for first time set up only. For future soft top procedures, refer to “soft top” in this section. 1. Locate and remove the following items prior to hard top removal:...

  • Page 76

    4. If the soft top has been removed, follow these steps to reinstall the soft top. If the soft top is on the vehicle, proceed to step #5. A. If the pivot brackets have been removed, unzip the sport bar cover and attach the pivot brackets and screws with a #t40 torx 威 head driver. Re-cover and re-zip...

  • Page 77

    5. Unsnap and remove the black boot cover. This cover should be discarded. It was intended as a protective cover for shipping only. Note: a visual instruction sheet is enclosed in the dual top wrap. 6. Open the tailgate. 7. Remove the tailgate bar (black bar with end caps) that is located in the sof...

  • Page 78

    11. Working from the rear of the vehicle with the tailgate open, lift the plastic header (with latches) up and over the sport bar. As the header reaches the top, locate the 2 bow and push it up and over the sport bar. 12. Move to the side of the vehicle and pull the side bow forward and down. You wi...

  • Page 79

    13. Unclip and move the sun visor to the side. 14. Open the header latches and engage the hooks on each side into the windshield slot. Note: do not latch at this time. 15. Grasp the drip rail retainers and untuck them from the door frame. The soft top fabric should cover the header completely from o...

  • Page 80

    Require you to pull some of the fabric down and around the corners. Repeat this step for the other side. Note: do not tuck the drip rail retainers into the frame at this time. 16. Move to the rear of the vehicle and gently pull the sail panels over the 3 bow letting them hang down. Make sure the nyl...

  • Page 81

    Attaching it with the velcro 威. Exit the vehicle, and go to the rear of the vehicle. Fold the rear seat and sit in the rear cargo area facing rearward. Look up at the 3 bow and locate the 4 snaps on the 3 bow. Grasp the fabric (fabric contains snaps), and pull it around the 3 bow, and attach all 4 s...

  • Page 82

    Note: this may be difficult due to fabric tension. If difficulty is experienced with fabric tension, place your hand on top of the 3 bow and gently pull down to help tuck in the sail panels. 19. To install the quarter windows, affix the rear corner of the quarter window temporarily to the velcro 威. ...

  • Page 83

    20. Tuck in the bottom retainers on the quarter windows into the bodyside retainer, beginning from the rear and working to the front of the vehicle. Repeat this step for the other side. 21. Locate the black retainer bar that was set aside, and the rear window. Remove and discard the end caps. Slide ...

  • Page 84

    22. Zip the rear window beginning from the left using both zipper ends. Run the upper zipper around the window to the right side leaving the lower zipper end at the start on the left. 23. Tuck in the retainer bar ends into the tailgate clips on each side of the tailgate opening. 84 understanding the...

  • Page 85

    24. Tuck the lower retainers on both sides of the rear window under the tailgate clips. Reinstall the left sail panel if it was untucked to get the rear window zipper started. 25. Tuck the drip rail retainers into the door frame slots above the door on both sides. Understanding the features of your ...

  • Page 86

    26. Close the header latches and return the sun visor to it’s secure position. Hard top caution! • the hard top is not designed to carry any addi- tional loads such as roof racks, spare tires, build- ing, hunting, or camping supplies, and/or lug- gage, etc. Also, it was not designed as a structural ...

  • Page 87

    Hard top removal 1. Fold down the sun visors and move them to the side. 2. Unlatch the two hard top latches located at the top of the windshield. 3. Unbolt the six torx 威 head screws which secure the hard top to the vehicle using a #40 torx 威 head driver. Caution! When removing the 2 front screws ju...

  • Page 88

    Note: on a dual top vehicle, the two rear and center nuts are retained onto the bodyside. 4. Open both doors. 5. Open tailgate all the way to ensure clearance of the rear window glass. Lift rear window glass. 6. Locate the wiring harness at the rear left side corner of the vehicle. 88 understanding ...

  • Page 89

    7. Disconnect the washer hose and install the tethered cap. Caution! Make sure storage cap is installed to prevent foreign materials from entering tube and clogging system. 8. Disconnect the wire harness from the hard top by pressing the tab at the side of the connector and pulling to disconnect. Un...

  • Page 90

    Note: if the red latch on the connector is locked, push the red latch to the right until you can only see the latch on one end (right) of the connector. This will unlock connector tab, allowing the tab to be pressed down and enabling the harness to be disconnected from the hard top. 9. Remove the ha...

  • Page 91

    Soft top caution! • the soft top is not designed to carry any addi- tional loads such as roof racks, spare tires, build- ing, hunting, or camping supplies, and/or lug- gage, etc. Also, it was not designed as a structural member of the vehicle, and thus cannot properly carry any additional loads othe...

  • Page 92

    Caution! • do not run a fabric top through an automatic car wash. Window scratches and wax build up may result. • do not lower the top when the temperature is below 41°f (5°c). Damage to the top may result. • do not lower the top when the windows are dirty. Grit may scratch the window. • do not move...

  • Page 93

    Etc., clean them with a mild soap solution and a small brush. Cleaning products are available through your authorized dealer. 1. If your vehicle has half doors, remove each half door window by opening the door and lifting the half door window out. Note: stow half doors carefully outside of the vehic...

  • Page 94

    3. Unclip and move the sun visor to the side. 4. Release the header latches and leave the hooks in the windshield slots. 5. Open the tailgate, partially unzip the rear window on each side, and untuck the lower retainers on the window from the tailgate clips on both sides of the tailgate opening. 94 ...

  • Page 95

    6. Pull the retainer bar straight out from the tailgate clips. • remove the rear window entirely. This is done by unzipping the window by bringing both the right zipper and left zipper tabs all the way to the end of the zipper track at the bottom left corner. Both zipper tabs will remain on the zipp...

  • Page 96

    8. Finish unzipping the window and untuck from the door frame retainer at the front of the window, repeat this step on the other side. Note: stow clean windows carefully outside of the vehicle to avoid scratches. 9. Untuck the sail panels from the bodyside retainer. Note: if difficulty is experience...

  • Page 97

    10. Completely release the hooks on the rear side of the windshield. Grasp the side bow behind the header and lift top back. 11. As you begin to lower the top, wrap the sail panels so that they rest on the roof of the vehicle. Note: if your vehicle is equipped with a dual top, prevent connector dama...

  • Page 98

    Tuck the top material between the 2 bow and the 3 bow as it folds. 13. Tuck the top material between the 2 bow and the header. 98 understanding the features of your vehicle.

  • Page 99

    14. After the top is folded down, ensure that the drip rail retainers are tucked in inward as shown. This is to avoid unnecessary wear to the fabric. 15. After the top is folded down, tuck the check straps so that they are not hanging and flapping outside the vehicle. Putting up the soft top note: b...

  • Page 100

    Over the sport bar. As the header reaches the top, locate the 2 bow and push it up and over the sport bar. 2. Move to the side of the vehicle and pull the side bow forward and down. Be sure the check straps are not tangled around the 2 bow. You will see the 3 bow rise from the rear of the vehicle. 1...

  • Page 101

    3. Unclip and move the sun visor to the side. 4. Open the header latches and engage the hook on each side into the windshield slot. Understanding the features of your vehicle 101 3.

  • Page 102

    5. Grasp the drip rail retainer and untuck them from the door frame. Note: do not tuck the drip rails into the door frame at this time. 6. Move to the rear of the vehicle and gently pull the sail panels over the 3 bow letting them hang down. 102 understanding the features of your vehicle.

  • Page 103

    7. Align the sail panel retainer to the edge of the bodys- ide retainer at the rear. Tuck the sail panel into the bodyside retainer beginning from the rear and working to the corner. Tuck the retainer around the corner and continue forward. Note: this may be difficult due to fabric tension. If diffi...

  • Page 104

    8. To install the quarter window, affix the rear corner of the window temporarily to the velcro 威. Start and zip the zipper only about 1 inch (2.5 cm). At this time it is necessary to tuck in the door frame retainer. 9. After the door frame retainer has been completely tucked in, finish zipping in t...

  • Page 105

    10. Tuck the bottom retainer of the quarter window into the bottom retainer, beginning from the rear and working to the front of the vehicle. Repeat this step for the other side. 11. To assist in getting the zipper started, lay the retainer bar inside the vehicle on the wheel wells and uninstall hal...

  • Page 106

    12. Zip in the rear window beginning from the left using both zipper ends. Run the upper zipper around the window leaving the lower zipper at the start. 13. Tuck the retainer bar into the tailgate clips. 106 understanding the features of your vehicle.

  • Page 107

    14. Tuck the lower retainers of the rear window under the tailgate clips. Reinstall the left corner if it was untucked to get the rear window zipper started. 15. Tuck the drip rail retainers into the door frame slot above the door on both sides. Understanding the features of your vehicle 107 3.

  • Page 108

    16. Close the header latches and return the sun visor to it’s secured position. Soft top — unlimited models caution! • the soft top is not designed to carry any addi- tional loads such as roof racks, spare tires, build- ing, hunting, or camping supplies, and/or lug- gage, etc. Also, it was not desig...

  • Page 109

    Place the vehicle in a warm area. Pull steadily on the top fabric. The vinyl will stretch back to its original size and the top can then be snapped into place. If temperature is 41°f (5°c) or below, do not attempt to put the top down or roll the rear or side curtains. Caution! • do not run a fabric ...

  • Page 110

    Warning! • do not drive vehicle with rear window curtain up unless side curtains are also open. Dangerous exhaust gases which can kill could enter the vehicle. • the fabric upper doors and fabric top are de- signed only for protection against the elements. Do not rely on them to contain occupants wi...

  • Page 111

    1. Grasp the fabric of the top above the door frame. Pull down and out on the fabric to untuck the drip rail retainers from the door frame slot. Start at the back of the rear drip rail retainer and work forward towards the windshield. Repeat this on the other side. 2. Unclip and move the sun visors ...

  • Page 112

    5. Grip and rotate the retainer bar up towards you to release it from the upper portion of the tailgate clips. The retainer bar runs along the bottom of the rear window. 6. Remove the rear window entirely. This is done by unzipping the window, bringing both the right zipper and the left zipper tabs ...

  • Page 113

    8. Finish unzipping the window and untuck from the door frame retainer at the front of the window, repeat this step on the other side. Note: stow clean windows carefully outside of the vehicle to avoid scratches. 9. Untuck the sail panels from the rear corners of the vehicle. Note: if difficulty is ...

  • Page 114

    10. Release the sunrider pins to release the top bows from the brackets located on both door rails. Push up and back on the bow slightly so it does not fall back and lock into the brackets. 11. Grasp the side bow behind the header and lift the top back. 114 understanding the features of your vehicle.

  • Page 115

    12. As you begin to lower the top, wrap the sail panels so that they rest on the roof of the vehicle. 13. Make sure the sides of the top are folded inward as the top continues to fold, and check straps are clear of the vehicle. Tuck the top between the 2 bow and 2-1/2 bow and 2-1/2 bow and 3 bow as ...

  • Page 116

    14. Tuck the top material between the 2 bow and the header. 15. After the top is folded down, ensure that the drip rail retainers are tucked in inward as shown. This is to avoid unnecessary wear to the fabric. 116 understanding the features of your vehicle.

  • Page 117

    16. After the top is folded down, tuck the check straps inside the rear corners of the vehicle. This will keep them from hanging and flapping outside the vehicle. 17. Hook the header latches back onto the header to keep them from rattling. Putting up the soft top note: be sure the wire harness is no...

  • Page 118

    3. Begin working from the rear of the vehicle with the tailgate open. Standing to the side of the vehicle, lift the top by the 2 bow and 3 bow over the sport bar. 4. Engage the hooks on each side of the header into the windshield slots and do not fully engage the header latch. If you close the latch...

  • Page 119

    5. Pull the side bow forward and down. Make certain the blocks on the side bows line up with the retainers on the door rails. Lock the blocks in place. Note: check to make certain the check straps are not tangled on any of the other top hardware. This will prevent the top from being put all the way ...

  • Page 120

    7. Tuck the sail panel retainer into the bodyside retainer. Begin working from the rear tailgate opening and work to the corner. Note: this may be difficult due to fabric tension. If difficulty is experienced with fabric tension, place your hand on top of the 3 bow and pull down to help tuck in the ...

  • Page 121

    8. To install the quarter windows, affix the upper rear corner of the window temporarily using the velcro 威. Next, start the zipper about 1 inch (2.5 cm) at the upper forward corner of the window. At this time it is necessary to tuck in the door frame retainer. 9. After the door frame retainer has b...

  • Page 122

    10. Tuck the bottom retainer on the quarter window into the bottom retainer, beginning from the rear and working to the front of the vehicle. Repeat this step for the other side. 11. Zip in the rear window beginning from the left using both zipper ends. Run the upper zipper around the window leaving...

  • Page 123

    Note: to assist in getting the zipper started, lay the bar inside the vehicle on the right wheel well, uninstall half of the left sail panel from the bodyside retainer, begin- ning near the tailgate open to expose zipper ends. 12. Tuck the retainer bar into the upper portion of the tailgate clips. U...

  • Page 124

    13. Tuck the lower retainers on the rear window under the tailgate clips. 14. Reinstall the corner of the sail panel that was un- tucked to get the rear window zipper started. 15. Tuck the drip rail retainers into the door frame slots above the door on both sides. Start at the front next to the wind...

  • Page 125

    16. Fully engage the header latch. 17. Return the sun visors to their secure position. Sunrider — if equipped (unlimited models only) note: if you are going to be driving faster than 40 mph (64 km/h) with the sunrider feature open, it is recom- mended that you remove the rear window of the vehicle. ...

  • Page 126

    To raise 1. Grasp the drip rail retainers and untuck both of them starting at the rear of the door frame slot. Repeat this on the other side. 2. Unclip and move the sun visors to the side. 3. Release the header latches, and slide the plastic sleeves forward. 126 understanding the features of your ve...

  • Page 127

    4. Grasp the header and lift the top back. Make sure the material is folded back as shown. Secure latches to plastic retainer on header. 5. Locate strap to secure the header to the sport bar. Wrap strap around sport bar and hook to header and tighten. 6. Attach and reposition sun visors. Understandi...

  • Page 128

    To lower 1. Remove strap from header and sport bar. 2. Release header latches from header retainer. 3. Unclip and move the sun visors to the side. 4. Grasp the front header and pull to the front of the vehicle. 5. Slide plastic sleeve rearward over sunrider link. 6. Tuck drip rail retainers into the...

  • Page 129

    2. Fold the door frames and store the knobs and door frames outside of the vehicle. Repeat this step for the other side. Warning! • use both hands to remove the door frames. The door frames will fold and could cause injury if both hands are not used. • never store the door frames in your vehicle. In...

  • Page 130

    3. Slide door frame forward until the pin holes in the top line up with the holes in the side bar. Screw in the knobs and tighten, beginning with the front knob. Repeat procedures on the other side. Folding windshield the fold down windshield and removable side bars on your vehicle are structural el...

  • Page 131

    If required for certain off-road uses, the side bars can be removed and the windshield folded down. However, the protection afforded by these features is then lost. If you remove the side bars and fold down the windshield, drive slowly and cautiously. It is recommended that the speed of the vehicle ...

  • Page 132

    Warning! Carefully follow these warnings to help protect against personal injury: • do not drive your vehicle on-road with the wind- shield down. • do not drive your vehicle unless the windshield is securely fastened, either up or down. • eye protection, such as goggles, should be worn at all times ...

  • Page 133

    3. Remove the two torx 威 head screws holding each side bar to the windshield frame. Shift the side bar inboard to clear windshield pillar molding when removing the side bar. Note: store all of the mounting bolts in their original threaded holes and tighten for safekeeping. 4. Unzip the sport bar pad...

  • Page 134

    Caution! Do not remove the head impact foam from the side bars, as damage to the foam may result. 5. To safely store the side bars in your vehicle, use four of the cinch straps, found in the glove box. Attach the straps through the footman loops located in the floor behind the folded rear seat on ea...

  • Page 135

    7. Remove the black round headed windshield torx 威 head screw on each side of the base of the windshield. 8. Lower the windshield gently until it contacts the rubber hood bumpers. Understanding the features of your vehicle 135 3.

  • Page 136

    9. Secure the windshield by passing the remaining cinch strap, found in the glove box, through the footman hoop on the center of the hood and on the center of the windshield frame. Tighten the strap to secure the wind- shield in place. Raising the windshield and replacing side bars to raise the wind...

  • Page 137

    Rear window features — hard top only rear window defogger to turn the rear window defogger on, press the rocker switch. If you press the switch a second time, you will turn the defogger off. A light on the rocker switch will indicate the defogger is on. The defogger will automatically turn off after...

  • Page 138

    Rear window wiper/washer to utilize the rear wiper, press the switch to the first detent. To activate the rear washer, depress the switch to the second detent. The washer will continue to spray as long as the switch is held. The switch will return to the wiper mode when released. To turn the rear wi...

  • Page 139: Contents

    Understanding your instrument panel contents 䡵 instrument panel and interior controls . . . . . . . 141 䡵 instrument cluster . . . . . . . . . . . . . . . . . . . . . . 142 䡵 instrument cluster description . . . . . . . . . . . . . 143 䡵 electronic digital clock . . . . . . . . . . . . . . . . . . 1...

  • Page 140

    ▫ radio operation . . . . . . . . . . . . . . . . . . . . . . 156 ▫ cd player operation . . . . . . . . . . . . . . . . . . . 159 䡵 satellite radio — if equipped . . . . . . . . . . . . . . 163 ▫ system activation . . . . . . . . . . . . . . . . . . . . . 164 ▫ electronic serial number/sirius identi...

  • Page 141

    Instrument panel and interior controls understanding your instrument panel 141 4.

  • Page 142

    Instrument cluster 142 understanding your instrument panel.

  • Page 143

    Instrument cluster description your vehicle is equipped with the instrument cluster described on the following pages. 1. Voltmeter indicates available battery voltage and charging system operation. The lower red zone indicates that battery charge may be too low to start the engine. With the engine r...

  • Page 144

    7. High beam indicator light this light shows that the headlights are on high beam. Pull the turn signal lever towards the steering wheel to switch the headlights from high or low. If the driver’s door is open, and the headlights or parklights are left on, the “high beam indicator light” will flash ...

  • Page 145

    13. Oil pressure gauge indicates engine oil pressure. This gauge does not indicate oil level, and pressure varies with engine speed, temperature and oil viscosity. Consistent lower readings indicate possible malfunction. Seek authorized service. 14. Coolant temperature gauge indicates engine coolant...

  • Page 146

    Certain conditions such as a loose or missing gas cap, poor quality fuel, etc. May illuminate the light after engine start. The vehicle should be serviced if the light stays on through several typical driving styles. In most situations, the vehicle will drive normally and will not require towing. Wh...

  • Page 147

    20. Anti-lock (abs) warning light after ignition is turned on, illuminates to indicate function check at vehicle start-up. If light remains on after start-up or comes on and stays on at road speeds, it may indicate that the abs has detected a malfunction or has become inoperative. The system reverts...

  • Page 148

    23. Fuel cap indicator this symbol indicates the side of the vehicle where the fuel cap is located. 24. Fuel gauge the pointer shows the level of fuel in the fuel tank. When the fuel gauge pointer initially moves to e, for your safety, approximately 2 u.S. Gallons (7.6l) of fuel remain. Note: when t...

  • Page 149

    Radio general information radio broadcast signals your new radio will provide excellent reception under most operating conditions. Like any system, however, car radios have performance limitations, due to mobile op- eration and natural phenomena, which might lead you to believe your sound system is ...

  • Page 150

    Remain active for up to 45 seconds after the ignition switch has been turned off. Opening a vehicle front door will cancel this feature. Sales code rbk—am/ fm stereo radio with cd player and cd changer controls radio operation power/volume control press the on/vol control to turn the radio on. Turn ...

  • Page 151

    The radio will continue to tune until you release the button. The frequency will be displayed and continu- ously updated while the button is pressed. To set the radio push-button memory when you are receiving a station that you wish to commit to push-button memory, press the set button. Set 1 will s...

  • Page 152

    Press the audio button a fourth time and fade will be displayed. Press the seek + or seek – to adjust the sound level between the front and rear speakers. Press the audio button again or wait 5 seconds to exit setting tone, balance, and fade. Am/fm selection press the am/fm button to change from am ...

  • Page 153

    Inserting the compact disc caution! This cd player will accept 4 3 ⁄ 4 inch (12 cm) discs only. The use of other sized discs may damage the cd player mechanism. You may either insert or eject a disc with the radio off. If you insert a disc with the ignition on and the radio off, the display will sho...

  • Page 154

    Ff/tune/rw press ff (fast forward) and the cd player will begin to fast forward until ff is released. The rw ( reverse) button works in a similar manner. Random play — rnd/program button 4 press the rnd (button 4) button while the cd is playing to activate random play. This feature plays the tracks ...

  • Page 155

    Disc up/program button 1 press the disc up (button 1) button to play the next available disc. Disc down/program button 5 press the disc down (button 5) button to play the previous disc. Seek button press the seek up or down to select another track on the same disc. A seek symbol will appear on the d...

  • Page 156

    Cd diagnostic indicators when driving over a very rough road, the cd player may skip momentarily. Skipping will not damage the disc or the player, and play will resume automatically. As a safeguard and to protect your cd player, one of the following warning symbols may appear on your display. A cd h...

  • Page 157

    Note: power to operate the radio is controlled by the ignition switch. It must be in the on or acc position to operate the radio. Mode press the mode button repeatedly to select between am, fm, the cd changer and sirius satellite radio™ (if equipped). The display will show st when a stereo station i...

  • Page 158

    And release that button. If a button is not selected within 5 seconds after pressing the set rnd button, the station will continue to play but will not be locked into push- button memory. You may add a second station to each push-button by repeating the above procedure with this exception: press the...

  • Page 159

    General information this radio complies with part 15 of fcc rules and with rss-210 of industry canada. Operation is subject to the following conditions: 1. This device may not cause harmful interference, 2. This device must accept any interference received, including interference that may cause unde...

  • Page 160

    Show the disc number, the track number, and index time in minutes and seconds. Play will begin at the start of track 1. Load/ ejt — load press the load/ ejt button and the button with the corresponding number where the cd is being loaded. After the radio displays “load” insert the cd into the player...

  • Page 161

    Ff/tune/rw press ff (fast forward) and the cd player will begin to fast forward until ff is released. The rw ( reverse) button works in a similar manner. Random play — set / rnd press the rnd button while the cd is playing to activate random play. This feature plays the tracks on the disc in random ...

  • Page 162

    Program type radio display nostalgia nostalga oldies oldies personality persnlty public public rhythm and blues r & b religious music rel musc religious talk rel talk rock rock soft soft soft rock soft rck soft rhythm and blues soft r&b sports sports talk talk top 40 top 40 weather weather by pressi...

  • Page 163

    Time press the time button to change the display from elapsed cd playing time to time of day. Operating instructions - satellite radio mode (if equipped) refer to the satellite radio section of the owner’s manual. Cd diagnostic indicators when driving over a very rough road, the cd player may skip m...

  • Page 164

    System activation to activate your sirius satellite radio service, call the toll-free number 888-539-7474, or visit the sirius web site at www.Sirius.Com. Please have the following informa- tion available when activating your system: 1. The electronic serial number/sirius identification number (esn/...

  • Page 165

    Mode when any other button is pushed, the ignition is turned off, or 5 minutes has passed since any button was pushed. Selecting satellite mode in rbb, rah and rbk radios press the mode button repeatedly until ⬙s a⬙ appears in the display. A cd or tape may remain in the radio while in the satellite ...

  • Page 166

    Note: channels that may contain objectionable content can be blocked. Contact sirius customer care at 888-539- 7474 to discuss options for channel blocking or unblock- ing. Please have your esn/sid information available. Storing and selecting pre-set channels in addition to the 10 am and 10 fm pre-s...

  • Page 167

    Satellite antenna to ensure optimum reception, do not place items on the roof around the rooftop antenna location. Metal objects placed within the line of sight of the antenna will cause decreased performance. Larger luggage items should be placed as far forward as possible. Do not place items direc...

  • Page 168

    5. A loose tape should be corrected before use. To rewind a loose tape, insert the eraser end of a pencil into the tape drive gear and twist the pencil in the required directions. Maintain your cassette tape player. The head and capstan shaft in the cassette player can pick up dirt or tape deposits ...

  • Page 169

    Radio operation and cellular phones under certain conditions, the cellular phone being on in your vehicle can cause erratic or noisy performance from your radio. This condition may be lessened or eliminated by relocating the cellular phone antenna. This condition is not harmful to the radio. If your...

  • Page 170

    Blower switch the blower switch is the rotary knob to the left of the controls. The blower speed will increase as the knob is turned clockwise. There are four blower speeds. Note: the blower motor will run until the mode control knob is turned to the “off” (“o”) position or the ignition is turned of...

  • Page 171

    Bi-level outside air comes from both instrument panel and floor outlets. Also, a slight amount of airflow may be noticed at the defrost outlet located at the base of the windshield. Floor outside air comes from the floor outlets. Also, a slight amount of airflow may be noticed at the defrost outlet ...

  • Page 172

    Temperature control the temperature control is the center knob located on the climate controls. It controls the temperature of the air delivered to the passenger compartment. You can choose your degree of comfort by rotating the knob. The coldest setting is to the extreme left (blue region) and the ...

  • Page 173

    Recirculation select this position when the outside air contains smoke, odors, high humidity, or if rapid cooling is desired. This feature allows for recirculation of interior air only. Air flows through the panel outlets in this mode. Also, a slight amount of airflow may be noticed at the defrost o...

  • Page 174

    Defrost outside air comes from the windshield outlets with a small amount being directed through the floor outlets. Use this setting when necessary to defrost your windshield. Note: for improved safety, the a/c compressor is activated when “mix” or “defrost” modes are selected. This is done to assis...

  • Page 175: Starting And Operating

    Starting and operating contents 䡵 starting procedures . . . . . . . . . . . . . . . . . . . . . 178 ▫ manual transmission . . . . . . . . . . . . . . . . . . 178 ▫ automatic transmission . . . . . . . . . . . . . . . . 178 ▫ normal starting . . . . . . . . . . . . . . . . . . . . . . 178 ▫ extreme c...

  • Page 176

    䡵 axle lock (tru–lok™) — if equipped . . . . . . . . 195 䡵 parking brake . . . . . . . . . . . . . . . . . . . . . . . . . 196 䡵 about your brakes . . . . . . . . . . . . . . . . . . . . . . 198 䡵 anti-lock brake system — if equipped . . . . . . . 200 䡵 on-road driving tips . . . . . . . . . . . . ....

  • Page 177

    䡵 fuel requirements . . . . . . . . . . . . . . . . . . . . . . 222 ▫ reformulated gasoline . . . . . . . . . . . . . . . . . 223 ▫ gasoline/oxygenate blends . . . . . . . . . . . . . . 223 ▫ mmt in gasoline . . . . . . . . . . . . . . . . . . . . . 224 ▫ materials added to fuel . . . . . . . . . . ...

  • Page 178

    Starting procedures before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. Warning! Do not leave children or animals inside parked vehicles in hot weather. Interior heat build up may cause serious injury or death. Manual transmission apply...

  • Page 179

    10 seconds, turn the key to the off position, wait 5 seconds, then repeat the normal starting procedure. Extreme cold weather (below –20°f or –29°c) to insure reliable starting at these temperatures, use of an externally powered electric engine block heater (available from your dealer) is recommende...

  • Page 180

    If the engine has been flooded, it may start to run, but not have enough power to continue running when the key is released. If this occurs, continue cranking with the accel- erator pedal pushed all the way to the floor. Release the accelerator pedal and the key once the engine is running smoothly. ...

  • Page 181

    Warning! Remember to disconnect the cord before driving. Damage to the 110-115 volt ac electrical cord could cause electrocution. Use the heater when temperatures below 0°f (-18°c) are expected to last for several days. Transmission shifting 6-speed manual transmission follow the shift pattern on th...

  • Page 182

    Warning! When parking your vehicle, always leave a manual transmission in first gear and apply the parking brake fully to guard against vehicle movement and possible injury or damage. Never use any gear as a substitute for the parking brake. Caution! To drive as safely as possible and to prolong the...

  • Page 183

    • push in the clutch pedal completely when shifting. Otherwise, transmission or clutch damage may result. • when “rocking” a stuck vehicle by shifting between a forward gear and reverse, do not spin wheels faster than 15 mph (24 km/h), or drivetrain damage may result. • the manual transmission may b...

  • Page 184

    Off-road driving (4l range only), which will allow crank- ing the engine without depressing the clutch, follow these steps: 1. Locate the power distribution center (pdc) in the engine compartment. Refer to “fuse panel” in section 7 of this manual. 2. Put a 10 amp fuse in the pdc cavity (#28) marked ...

  • Page 185

    Warning! It is dangerous to shift the selector lever out of “p” or “n” if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in re- verse. You could lose control of the vehicle and hit someone or something. Only ...

  • Page 186

    Warning! Unintended movement of a vehicle could injure those in and near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, you should always shift the vehicle into p (park), remove the key from the ignition, and apply the parkin...

  • Page 187

    Caution! Before moving the shift lever out of p (park), you must turn the ignition from lock to on so the steering wheel and shift lever are released. Other- wise, damage to the steering column or shifter could result. R (reverse) for moving the vehicle rearward. Always stop before moving the lever ...

  • Page 188

    When frequent transmission shifting occurs while using overdrive, such as when operating the vehicle under heavy load conditions (for example, in hilly terrain, strong head winds, or trailer towing), turning off over- drive will improve performance and extend transmission life by reducing excessive ...

  • Page 189

    Warning! Never use p (park) position with an automatic trans- mission as a substitute for the parking brake. Al- ways apply parking brake fully when parked to guard against vehicle movement and possible injury or damage. Caution! • before moving the shift lever out of p (park), you must turn the ign...

  • Page 190

    Note: the transmission electronics constantly monitor the transmission oil temperature. If the transmission gets too hot, the transmission will change the way it shifts to help control the condition. This may result in a slightly different feeling or response during normal operation in d (drive) pos...

  • Page 191

    Operating instructions/precautions the transfer case provides four mode positions — two (rear) wheel drive high range, four wheel drive high range, neutral, and four wheel drive low range. This transfer case is intended to be driven in the two wheel drive (2h) position for normal street and highway ...

  • Page 192

    Proper operation of four wheel drive vehicles depends on tires of equal size, type, and circumference on each wheel. Any difference will adversely affect shifting and cause damage to the transfer case. Because four wheel drive provides improved traction, there is a tendency to exceed safe turning an...

  • Page 193

    4l position four wheel drive low range — locks the front and rear driveshafts together. Forces the front and rear wheels to rotate at the same speed. Additional traction and maxi- mum pulling power for loose, slippery road surfaces only. Do not exceed 25 mph (40 km/h). Shifting procedure 2h to 4h or...

  • Page 194

    Warning! Failure to engage a position completely can cause transfer case damage or loss of power and vehicle control. You could have an injury accident. Do not drive the vehicle unless the transfer case is fully engaged. Trac-lok™ rear axle the trac-lok™ rear axle provides a constant driving force t...

  • Page 195

    Axle lock (tru–lok™) — if equipped the axle lock switch is located on the lower center of the instrument panel. This feature will only activate when the following con- ditions are met: • key in ignition, vehicle in 4l (low) range. • the vehicle must be traveling at 10 mph (16 km/h) or less. To activ...

  • Page 196

    Parking brake to set the parking brake, pull the lever up as firmly as possible. When the parking brake is applied with the ignition on, the brake warning light in the instrument cluster will light. Note: the brake warning light indicates only that the parking brake is applied. It does not indicate ...

  • Page 197

    Note: your vehicle has automatically adjusting rear brakes and we do not recommend any adjustment other than the maintenance performed by your authorized dealer. Before leaving the vehicle parked on a hill, you must make sure the parking brake is fully applied and place the gear selector in the p (p...

  • Page 198

    The parking brake should always be applied when the driver is not in the vehicle. Warning! • leaving children unattended in a vehicle is dan- gerous for a number of reasons. A child or others could be injured. Children should be warned not to touch the parking brake or the gear selector lever. Don’t...

  • Page 199

    Warning! To use your brakes and decelerate more safely, follow these tips: • do not “ride” the brakes by resting your foot on the pedal. This could overheat the brakes and result in unpredictable braking action, longer stopping distances, or brake damage. • when descending mountains or hills, repeat...

  • Page 200

    Warning! To help avoid personal injury, follow these tips: • never reach through the steering wheel to operate steering column controls. Injury to your hands or loss of vehicle control may result. • if the engine stalls or power assist fails due to a malfunction, vehicle steering and braking will re...

  • Page 201

    Regulated hydraulic pressure. The motor pump makes a low humming noise during operation, this is normal. During off-road use, loss of traction can temporarily defeat the system and cause the warning light to illumi- nate. Turn the ignition off and on again to restore anti-lock brake system function....

  • Page 202

    Caution! The anti-lock brake system is subject to possible detrimental effects of electronic interference caused by improperly installed aftermarket radios or tele- phones. Note: during severe braking conditions, a pulsing sensation may occur and a clicking noise will be heard. This is normal, indic...

  • Page 203

    Where additional low speed pulling power is needed. Vehicle speeds in excess of 25 mph (40 km/h) should be avoided when in 4l (low) range. Driving through water although your vehicle is capable of driving through water, there are a number of precautions that must be considered before entering the wa...

  • Page 204

    Standing water avoid driving in standing water deeper than 20 inches, and reduce speed appropriately to minimize wave ef- fects. Maximum speed in 20 inches of water is less than 5 mph (8 km/h). Maintenance after driving through deep water, inspect your vehicle fluids and lubricants (engine oil, tran...

  • Page 205

    Your speed. If the brakes are required to control vehicle speed, apply them lightly and avoid locking or skidding the tires. Warning! If the engine stalls or you lose headway or cannot make it to the top of a steep hill or grade, never attempt to turn around. To do so may result in tipping and rolli...

  • Page 206

    After driving off-road off-road operation puts more stress on your vehicle than does most on-road driving. After going off-road it is always a good idea to check for damage. That way you can get any problems taken care of right away and have your vehicle ready when you need it. • completely inspect ...

  • Page 207

    Tire safety information tire markings note: • p(passenger)-metric tire sizing is based on u.S. Design standards. P-metric tires have the letter “p” molded into the sidewall preceding the size designation. Ex- ample: p215/65r15 95h. • european metric tire sizing is based on european design standards....

  • Page 208

    Tire sizing chart example: size designation: p = passenger car tire size based on u.S. Design standards ⴖ....Blank....ⴖ = passenger car tire based on european design standards lt = light truck tire based on u.S. Design standards t = temporary spare tire 31 = overall diameter in inches (in) 215 = sec...

  • Page 209

    Example: service description: 95 = load index —a numerical code associated with the maximum load a tire can carry. H = speed symbol —a symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions. —the maximum speed corresp...

  • Page 210

    Tire identification number (tin) the tin may be found on one or both sides of the tire however the date code may only be on one side. Tires with white sidewalls will have the full tin including date code located on the white sidewall side of the tire. Look for the tin on the outboard side of black s...

  • Page 211

    Tire loading and tire pressure tire placard location note: the proper cold tire inflation pressures are listed on the lower front inside corner of the driver door opening. Tire and loading information placard this placard tells you important information about the, 1) number of people that can be car...

  • Page 212

    Loading the vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size and cold tire inflation pressures specified on the tire and loading informatio...

  • Page 213

    5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in step 4. 6. If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. Consult th...

  • Page 214

    214 starting and operating.

  • Page 215

    Warning! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. Tires — general information proper tire inflation pressure is essential...

  • Page 216

    2. Economy— improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Under inflation also increases tire rolling resistance and results in higher fuel consump- t...

  • Page 217

    More often if subject to a wide range of outdoor tempera- tures, as tire pressures vary with temperature changes. Inflation pressures specified on the label are always “cold inflation pressure.” cold inflation pressure is defined as the tire pressure after the vehicle has been idle for at least 3 ho...

  • Page 218

    Radial-ply tires warning! Combining radial ply tires with other types of tires on your vehicle will cause your vehicle to handle poorly. The instability could cause an accident. Al- ways use radial tires in sets of four. Never combine them with other types of tires. Cuts and punctures in radial tire...

  • Page 219

    Overloading your vehicle, long trips in very hot weather, and driving on bad roads may result in greater wear. Replacement tires the tires on your new vehicle provide a balance of many characteristics. They should be inspected regularly for wear and correct inflation pressure. The manufacturer stron...

  • Page 220

    Warning! • do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change suspen- sion dimensions and performance characteristics, resulting in changes to steering, handling, and brak- ing of your vehicle. This can caus...

  • Page 221

    Tires may also cause the vehicle to pull left or right. Alignment will not correct this problem. See your dealer for proper diagnosis of the problem. Improper alignment will not normally cause vehicle vibration, which may be a result of tire and wheel out-of-balance. Proper balancing will reduce vib...

  • Page 222

    Aggressive tread designs such as those on on/off road type tires. Rotation will increase tread life, help to main- tain mud, snow, and wet traction levels, and contribute to a smooth, quiet ride. Follow the recommended tire rotation frequency for your type of driving found in the “maintenance schedu...

  • Page 223

    Premium gasoline will provide no benefit over high quality regular gasoline, and in some circumstances may result in poorer performance. Light spark knock at low engine speeds is not harmful to your engine. However, continued heavy spark knock at high speeds can cause damage and immediate service is...

  • Page 224

    Caution! Do not use gasoline containing methanol. Gasoline containing methanol may damage critical fuel system components. Mmt in gasoline mmt is a manganese containing metallic additive that is blended into some gasoline to increase octane. Gasoline blended with mmt provides no performance advantag...

  • Page 225

    • the use of leaded gas is prohibited by federal law. Using leaded gasoline can impair engine performance, damage the emission control system. • an out-of-tune engine, or certain fuel or ignition malfunctions, can cause the catalytic converter to overheat. If you notice a pungent burning odor or som...

  • Page 226

    The vehicle is raised. Have any abnormal conditions repaired promptly. Until repaired, drive with all side windows fully open. • keep the swing gate closed when driving your vehicle to prevent carbon monoxide and other poisonous exhaust gases from entering the vehicle. Fuel filler cap (gas cap) the ...

  • Page 227

    Caution! Damage to the fuel system or emission control system could result from using an improper fuel cap (gas cap). A poorly fitting cap could let impurities into the fuel system. Also, a poorly fitting after- market cap can cause the mil (malfunction indica- tor light) to illuminate, due to fuel ...

  • Page 228

    Warning! • remove the fuel cap (gas cap) slowly to prevent fuel spray from the filler neck which may cause injury. • the volatility of some gasoline may cause a buildup of pressure in the fuel tank that may increase while you drive. This pressure can result in a spray of gasoline and/or vapors when ...

  • Page 229

    • be sure to remove the key. Caution! To avoid fuel spillage and overfilling, do not “top off” the fuel tank after filling. Note: when the fuel nozzle “clicks” or shuts off, the fuel tank is full. Trailer towing in this section you will find information on limits to the type of towing you can reason...

  • Page 230

    A load equalizing hitch is recommended for loaded trailer weights above 1,000 lbs (454 kg). Caution! If the trailer weighs more than 1,000 lbs (454 kg) loaded, it should have its own brakes and they should be of adequate capacity. Failure to do this could lead to accelerated brake lining wear, highe...

  • Page 231

    Starting and operating 231 5.

  • Page 232

    Note: refer to “recommended fluids, lubricants, and genuine parts” in section 7 for axle differential lubrica- tion specifications for towing. Recreational towing (behind motorhome, etc.) caution! Internal damage to the transfer case will occur if a front or rear wheel lift is used when recreational...

  • Page 233

    5. Shift automatic transmission into d (drive) or manual transmission into gear. 6. Release brake pedal and ensure that there is no vehicle movement. 7. Shut the engine off and place the ignition key into the unlocked off position. 8. Shift automatic transmission into p (park). 9. Apply parking brak...

  • Page 234

    Note: when shifting out of transfer case n (neutral) on automatic transmission equipped vehicles, turning the engine off may be required to avoid gear clash. Warning! You or others could be injured if you leave the vehicle unattended with the transfer case in the n (neutral) position without first f...

  • Page 235: Contents

    What to do in emergencies contents 䡵 hazard warning flasher . . . . . . . . . . . . . . . . . . 236 䡵 if your engine overheats . . . . . . . . . . . . . . . . . 237 䡵 jacking and tire changing . . . . . . . . . . . . . . . . 238 ▫ jack location . . . . . . . . . . . . . . . . . . . . . . . . 238 ▫ s...

  • Page 236

    Hazard warning flasher the flasher switch is on top of the steering column, just behind the steering wheel. Depress the switch and both cluster indicators and all front and rear directional sig- nals will flash. Depress the switch again to turn hazard warning flashers off. Hazard flasher switch 236 ...

  • Page 237

    Do not use this emergency warning system when the vehicle is in motion. Use it when your vehicle is disabled and is creating a safety hazard for other motorists. If it is necessary to leave the vehicle to go for service, the flasher system will continue to operate with the ignition key removed and t...

  • Page 238

    Jacking and tire changing warning! • getting under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never get any part of your body under a vehicle that is on a jack. If you need to get under a raised vehicle, take it to a service center wh...

  • Page 239

    Spare tire stowage to remove the spare tire from the carrier, remove the tire cover, if equipped, and remove the lug nuts with the lug wrench turning them counterclockwise. Note: if you have added aftermarket accessories to the spare tire mounted carrier, it cannot exceed a gross weight of 50 lbs (2...

  • Page 240

    • block both the front and rear of the wheel diagonally oppo- site of the jacking position. For example, if changing the right front tire, block the left rear wheel. • passengers should not remain in the vehicle when the vehicle is being jacked. Jacking instructions 1. Remove spare tire, jack and to...

  • Page 241

    And enough clearance is obtained to install the spare tire. Minimum tire lift provides maximum stability. Warning! Raising the vehicle higher than necessary can make the vehicle less stable and cause an accident. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to r...

  • Page 242

    Jump starting warning! To prevent personal injury or damage to clothing, do not allow battery fluid to contact eyes, skin, or fabrics. Do not lean over a battery when connecting jumper cables or allow cable clamps to touch each other. Keep open flames or sparks away from battery vent holes. Always w...

  • Page 243

    1. Attach one end of the jumper cable to the positive terminal of the discharged battery and the other end of the same cable to the positive terminal of the booster battery. Warning! Do not permit vehicles to touch each other as this could establish a ground connection and personal injury could resu...

  • Page 244

    4. After the engine is started or if the engine fails to start, the cables must be disconnected in the following order: a. Disconnect the negative cable at the engine ground. B. Disconnect the negative cable at the negative termi- nal on the booster battery. C. Disconnect the cable from the positive...

  • Page 245: Maintaining Your Vehicle

    Maintaining your vehicle contents 䡵 2.4l engine . . . . . . . . . . . . . . . . . . . . . . . . . . . 248 䡵 4.0l engine . . . . . . . . . . . . . . . . . . . . . . . . . . . 249 䡵 onboard diagnostic system — obd ii . . . . . . . . 250 䡵 emissions inspection and maintenance programs . . . . . . . . ....

  • Page 246

    ▫ air conditioner maintenance . . . . . . . . . . . . . 262 ▫ power steering fluid check . . . . . . . . . . . . . . 263 ▫ driveline and steering component lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . 264 ▫ body lubrication . . . . . . . . . . . . . . . . . . . . . 264 ▫ windshiel...

  • Page 247

    ▫ front side marker . . . . . . . . . . . . . . . . . . . . . 292 ▫ front fog light . . . . . . . . . . . . . . . . . . . . . . 292 ▫ rear tail, stop, turn signal, and back-up lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 294 ▫ center high mounted stop light (chmsl) . . . 294 䡵 fl...

  • Page 248

    2.4l engine 248 maintaining your vehicle.

  • Page 249

    4.0l engine maintaining your vehicle 249 7.

  • Page 250

    Onboard diagnostic system — obd ii your vehicle is equipped with a sophisticated onboard diagnostic system called obd ii. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide ex...

  • Page 251

    Emissions inspection and maintenance programs in some localities, it may be a legal requirement to pass an inspection of your vehicle’s emissions control system. Failure to pass could prevent vehicle registration. For states which have an i/m (inspection and maintenance) requirement, this check veri...

  • Page 252

    Ignition key or start the engine. This means that your vehicle’s obd system is not ready and you should not proceed to the i/m station. B. The mil will not flash at all and will remain fully illuminated until you turn off the ignition key or start the engine. This means that your vehicle’s obd syste...

  • Page 253

    Note: intentional tampering with emissions control systems can result in civil penalties being assessed against you. Warning! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the proper equipment. If you have any doubt abou...

  • Page 254

    The best time to check the engine oil level is about 5 minutes after a fully warmed engine is shut off, or before starting the engine after it has sat overnight. Checking the oil while the vehicle is on level ground will improve the accuracy of the oil level readings. Maintain the oil level between ...

  • Page 255

    • more than 50% of your driving is at sustained high speeds during hot weather, above 90°f (32°c) • taxi, police, or delivery service (commercial service) • trailer towing • off-road or desert driving • if equipped for and operating with e–85 (ethanol) fuel if any of these apply to you, then change ...

  • Page 256

    Engine oil viscosity (2.4l engines) sae 5w-30 engine oil is recommended for all operating temperatures. This engine oil improves low tempera- ture starting and vehicle fuel economy. Refer to your engine oil filler cap for the recommended engine oil viscosity for your vehicle. Engine oil viscosity (4...

  • Page 257

    Materials added to engine oils the manufacturer strongly recommends against the ad- dition of any additives (other than leak detection dyes) to engine oil. Engine oil is an engineered product and it’s performance may be impaired by supplemental addi- tives. Disposing of used engine oil care should b...

  • Page 258

    Special tools are required to properly measure tension and to restore belt tension to factory specifications. Also, check belt routing to make sure there is no interference between the belts and other engine components. Spark plugs spark plugs must fire properly to assure engine perfor- mance and em...

  • Page 259

    Warning! A hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your ex- haust system. Do not park or operate your vehicle in areas where your exhaust system can contact any- thing that can burn. In unusual sit...

  • Page 260

    Engine timing belt — 2.4l engine replace the engine timing belt at the intervals described in the appropriate maintenance schedule. Ignition wiring system — 2.4l engine replace the ignition cables at the intervals described in the appropriate maintenance schedule. Crankcase emission control system p...

  • Page 261

    Warning! The air cleaner can provide protection in the case of engine backfire. Do not remove the air cleaner unless it is necessary for repair or maintenance. Make sure that no one is near the engine compart- ment before starting the vehicle with the air cleaner removed. Failure to do so can result...

  • Page 262

    To determine the battery charge, check the battery test indicator (if equipped) on top of the battery. Refer to the illustration. Caution! It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negat...

  • Page 263

    Warning! • use only refrigerants and compressor lubricants approved by the manufacturer for your air condi- tioning system. Some unapproved refrigerants are flammable and can explode, injuring you. Other unapproved refrigerants or lubricants can cause the system to fail, requiring costly repairs. Re...

  • Page 264

    Warning! Fluid level should be checked on a level surface with the engine off to prevent injury from moving parts, and to insure accurate fluid level reading. Do not overfill. Use only the manufacturer’s recommended fluid. If necessary, add fluid to restore to the proper indicated level. With a clea...

  • Page 265

    Amount of a high quality lubricant such as mopar 威 lock cylinder lubricant directly into the lock cylinder. Windshield wiper blades clean the rubber edges of the wiper blades and the windshield periodically with a sponge or soft cloth and a mild non-abrasive cleaner. This will remove accumula- tions...

  • Page 266

    Warning! Commercial windshield washer solvents are flam- mable. They could ignite and burn you. Care must be exercised when filling or working around the washer solution. Exhaust system the best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust sy...

  • Page 267

    System should be drained, flushed and refilled with fresh antifreeze/coolant. Check the front of the a/c condenser (if equipped) or radiator for any accumulation of bugs, leaves, etc. If dirty, clean by gently spraying water from a garden hose vertically down the face of the a/c con- denser (if equi...

  • Page 268

    Caution! • mixing of antifreeze/coolant other than the speci- fied hoat antifreeze/coolant may result in de- creased corrosion protection and engine damage. If a non-hoat antifreeze/coolant is introduced into the cooling system in an emergency, it should be replaced with the specified antifreeze/coo...

  • Page 269

    Use only high purity water such as distilled or deionized water when mixing the water/antifreeze (coolant) solu- tion. The use of lower quality water will reduce the amount of corrosion protection in the engine cooling system. Please note that it is the owner’s responsibility to main- tain the prope...

  • Page 270

    Children, do not store ethylene glycol based antifreeze/ coolant in open containers or allow it to remain in puddles on the ground. If ingested by a child, contact a physician immediately. Clean up any ground spills im- mediately. Engine coolant level the coolant bottle provides a quick visual metho...

  • Page 271

    Coolant needs to be added, contents of coolant recov- ery bottle must also be protected against freezing. • if frequent antifreeze/coolant additions are required, or if the level in the recovery bottle does not drop when the engine cools, the cooling system should be pressure tested for leaks. • mai...

  • Page 272

    Are present. Components should be replaced immedi- ately if there is any evidence of degradation that could cause failure. Brake system in order to assure brake system performance, all brake system components should be inspected periodically. Refer to the appropriate “maintenance schedule” in sectio...

  • Page 273

    Warning! Worn brake hoses can burst and cause brake failure. You could have an accident. If you see any signs of cracking, scuffing, or worn spots, have the brake hoses replaced immediately. Brake master cylinder the fluid level in the master cylinder should be checked when performing under hood ser...

  • Page 274

    Should be checked when pads are replaced. However, low fluid level may be caused by a leak and a checkup may be needed. Use only manufacturer’s recommended brake fluid, refer to recommended fluids, lubricants, and genuine parts for correct fluid type. Warning! • use of a brake fluid that may have a ...

  • Page 275

    Caution! Using a transmission fluid other than the manufac- turer’s recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder. Using a transmission fluid other than the manufacturer’s recommended fluid will result in more frequent fluid and filter change...

  • Page 276

    (cross-hatched area) on the oil level indicator. The fluid level indicator should be in the cold region at 70° f (21° c) fluid temperature. If the fluid level is low, add sufficient fluid to bring to the proper level. Refer to recommended fluids, lubricants and genuine parts for correct fluid type. ...

  • Page 277

    Frequency of fluid change under normal operating conditions, the fluid installed at the factory will give satisfactory lubrication for the life of the vehicle. Fluid changes are not necessary unless the lubricant has become contaminated with water. If con- taminated with water, the fluid should be c...

  • Page 278

    Caution! When replacing plugs, do not overtighten. You could damage them and cause them to leak. Selection of lubricant use only manufacturer’s recommended fluid, refer to recommended fluids, lubricants, and genuine parts for correct fluid type. Front/rear axle fluid fluid level check lubricant shou...

  • Page 279

    Selection of lubricant use only manufacturer’s recommended fluid, refer to recommended fluids, lubricants, and genuine parts for correct fluid type. Appearance care and protection from corrosion protection of body and paint from corrosion vehicle body care requirements vary according to geo- graphic...

  • Page 280

    Washing • wash your vehicle regularly. Always wash your ve- hicle in the shade using a mild car wash soap and rinse the panels completely with clear water. • if insects, tar, or other similar deposits have accumu- lated on your vehicle, wash it as soon as possible. • use mopar威 auto polish to remove...

  • Page 281

    • be especially careful when washing the windows by following the directions for “care of fabric top win- dows.” washing — always use mild soap suds, lukewarm water, and a brush with soft bristles. If extra cleaning is required, use a mild foaming cleaner on the entire top, but support top from unde...

  • Page 282

    Soft top zipper cleaner and lubricant to ease zipper operation. Before applying, make sure the zipper teeth are clear of sand, mud, and other materials. Clean both sides of the zipper, not just one side. Rinse both zipper halves with fresh water and allow to dry. Aggressively work the mopar 威 soft t...

  • Page 283

    Do not use scouring pads or metal polishes. Avoid automatic car washes that use acidic solutions or harsh brushes that may damage the wheels’ protective fin- ish. Interior care use mopar 威 fabric cleaner to clean fabric upholstery and carpeting. Use mopar 威 vinyl cleaner to clean vinyl or leather up...

  • Page 284

    Warning! Only remove the carpet for cleaning purposes. It provides insulation against high floor pan tempera- tures. You or your passengers could be burned if the carpet is not properly in place. Always put the carpet back into the vehicle before driving. Follow these steps to remove the carpet: 1. ...

  • Page 285

    Seat belt maintenance do not bleach, dye or clean the belts with chemical solvents or abrasive cleaners. This will weaken the fabric. Sun damage will also weaken the fabric. If the belts need cleaning, use a mild soap solution or lukewarm water. Do not remove the belts from the vehicle to wash them....

  • Page 286

    Fuse panel interior fuses the fuse panel is located behind the glove box. To access the fuse panel the glove box must be removed. It is removed by slipping the glove box strap off the hook and letting the door roll down off its hinges. To reinstall, position the glove box door at an 8 o’clock orient...

  • Page 287

    Cavity fuse description 1 20 amp yel- low park lights, skim (sentry key) 2 20 amp yel- low stop lights 3 20 amp yel- low subwoofer system 4 10 amp red door switch defeat 5 10 amp red airbag 6 20 amp yel- low rear wiper 7 10 amp red back-up lights, rear win- dow defroster relay, abs 8 10 amp red heva...

  • Page 288

    Underhood fuses (power distribution center) your vehicle is equipped with an electrical power distri- bution center located in the engine compartment near the battery. This power center houses plug-in “cartridge” fuses, iso relays, and mini (micro) fuses. A label inside the latching cover of the cen...

  • Page 289

    Cavity fuse/color description 13 40 amp green accessories 14 open 15 50 amp red iod 16 open 17 20 amp yellow power 18 20 amp yellow horn 19 20 amp yellow fog lights 20 15 amp lt. Blue radio 21 10 amp red a/c clutch 22 25 amp natural ignition switch 23 20 amp yellow fuel 24 20 amp yellow off road 25 ...

  • Page 290

    Vehicle storage if you are leaving your vehicle dormant for more than 21 days you may want to take steps to protect your battery. You may: • remove cartridge fuse #15 in the power distribution center labeled ignition-off draw (iod). • store the removed iod fuse in the power distribution center locat...

  • Page 291

    Fog lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . H3 front park/turn lights (2) . . . . . . . . . . . . . . . . . 3157 front side marker lights (2) . . . . . . . . . . 168 or w3w headlights (2) . . . . . . . . . . . . . . . . . . . . . . H 6024bl stop/tail/turn lights (2) . . . ...

  • Page 292

    4. Remove and replace the lamp. Front park/turn signal 1. Reach under the front fender and locate the front park/turn signal socket. 2. Turn the socket assembly counter–clockwise 1/3 turn and remove it from the housing. Pull the bulb straight from the socket to replace. Front side marker 1. Reach un...

  • Page 293

    3. Squeeze the bulb/element spring retainer from the reflector. 4. Disconnect the electrical connector. Caution! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol. Ma...

  • Page 294

    Rear tail, stop, turn signal, and back-up lights 1. Remove the screws attaching the lens to the tailight housing. 2. Separate the lens from the housing. 3. Push the bulb in, turn it counter-clockwise 1/3 turn, then remove it from the housing, and replace. Center high mounted stop light (chmsl) the s...

  • Page 295

    Fluid capacities u.S. Metric fuel (approximate) 19 gallons 71.9 liters engine oil with filter 2.4 liter engine (sae 5w-30, api certified engine oil) 5 qts 4.7 liters 4.0 liter engine (sae 10w-30, api certified engine oil) 6 qts 5.7 liters cooling system * 2.4 liter engine (mopar 威 antifreeze/engine ...

  • Page 296

    Recommended fluids, lubricants and genuine parts engine component fluid, lubricant, or genuine part engine coolant mopar 威 antifreeze/coolant 5 year/100,000 mile formula hoat (hybrid or- ganic additive technology) engine oil api certified sae 5w-30 engine oil is recommended for the 2.4l engine. Api ...

  • Page 297

    Chassis component fluid, lubricant, or genuine part automatic transmission mopar 威 atf+4 automatic transmission fluid or equivalent. Manual transmission mopar 威 manual transmission lubricant or equivalent (meeting the require- ments of daimlerchrysler material standard ms-9224) transfer case mopar 威...

  • Page 298

    Component fluid, lubricant, or genuine part brake master cylinder mopar 威 dot 3 brake fluid, sae j1703 should be used. If dot 3, sae j1703 brake fluid is not available, then dot 4 is acceptable. Use only recom- mended brake fluids. Power steering reservoir mopar 威 atf+4 automatic transmission fluid ...

  • Page 299: Maintenance Schedules

    Maintenance schedules contents 䡵 emission control system maintenance . . . . . . . . 300 䡵 maintenance schedules . . . . . . . . . . . . . . . . . . . 300 ▫ schedule “b” . . . . . . . . . . . . . . . . . . . . . . . . 303 ▫ schedule “a” . . . . . . . . . . . . . . . . . . . . . . . . 314 8 m a i n t...

  • Page 300

    Emission control system maintenance the “scheduled” maintenance services, listed in bold type must be done at the times or mileages specified to assure the continued proper functioning of the emission control system. These, and all other maintenance services included in this manual, should be done t...

  • Page 301

    • off-road or desert driving • if equipped for and operated with e-85 (ethanol) fuel. Note: if any of these apply to you then change your engine oil every 3,000 miles (5 000 km) or 3 months, whichever comes first and follow “schedule b” of the “maintenance schedules” section of this manual. Note: if...

  • Page 302

    Once a month • check the tire pressure and look for unusual wear or damage. • inspect the battery and clean and tighten the terminals as required. • check the fluid levels of the coolant reservoir, brake master cylinder, and transmission, and add as needed. • check all lights and all other electrica...

  • Page 303

    Schedule “b” follow this schedule if you usually operate your vehicle under one or more of the following conditions. • day or night temperatures are below 32°f (0°c) • stop and go driving • excessive engine idling • driving in dusty conditions • short trips of less than 10 miles (16.2 km) • more tha...

  • Page 304

    Miles 3,000 6,000 9,000 12,000 15,000 (kilometers) (5 000) (10 000) (14 000) (19 000) (24 000) change the engine oil and engine oil filter, if not replaced at 3 months. X x x x x rotate the tires. X x inspect the engine air filter element, replace if necessary. X lubricate the steering linkage tie r...

  • Page 305

    Miles 18,000 21,000 24,000 27,000 30,000 (kilometers) (29 000) (34 000) (38 000) (43 000) (48 000) change the engine oil and engine oil filter, if not replaced at 3 months. X x x x x rotate the tires. X x x inspect the engine air filter element, replace if necessary. X inspect the pcv valve, and rep...

  • Page 306

    Miles 33,000 36,000 39,000 42,000 45,000 (kilometers) (53 000) (58 000) (62 000) (67 000) (72 000) change the engine oil and engine oil filter, if not replaced at 3 months. X x x x x rotate the tires. X x inspect the engine air filter element, replace if necessary. X lubricate the steering linkage t...

  • Page 307

    Miles 48,000 51,000 54,000 57,000 60,000 (kilometers) (77 000) (82 000) (86 000) (91 000) (96 000) change the engine oil and engine oil filter, if not replaced at 3 months. X x x x x rotate the tires. X x x inspect the engine air filter element, replace if necessary. X inspect the pcv valve, and rep...

  • Page 308

    Miles 48,000 51,000 54,000 57,000 60,000 (kilometers) (77 000) (82 000) (86 000) (91 000) (96 000) inspect the drive belt and replace as needed. Not required if belt was previously. X drain and refill the transfer case fluid. X flush and replace the engine coolant/anti-freeze at 60 months, if not do...

  • Page 309

    Miles 63,000 66,000 69,000 72,000 75,000 (kilometers) (101 000) (106 000) (110 000) (115 000) (120 000) change the engine oil and engine oil filter, if not replaced at 3 months. X x x x x rotate the tires. X x inspect the engine air filter element, replace if necessary. X lubricate the steering link...

  • Page 310

    Miles 78,000 81,000 84,000 87,000 90,000 (kilometers) (125 000) (130 000) (134 000) (139 000) (144 000) change the engine oil and engine oil filter, if not replaced at 3 months. X x x x x rotate the tires. X x x inspect the engine air filter element, replace if necessary. X inspect the pcv valve, an...

  • Page 311

    Miles 93,000 96,000 99,000 102,000 105,000 (kilometers) (149 000) (154 000) (158 000) (163 000) (168 000) change the engine oil and engine oil filter, if not replaced at 3 months. X x x x x rotate the tires. X x inspect the engine air filter element, replace if necessary. X lubricate the steering li...

  • Page 312

    Miles 108,000 111,000 114,000 117,000 120,000 (kilometers) (173 000) (178 000) (182 000) (187 000) (192 000) change the engine oil and engine oil filter, if not replaced at 3 months. X x x x x rotate the tires. X x x inspect the engine air filter element, replace if necessary. X inspect the pcv valv...

  • Page 313

    Miles 108,000 111,000 114,000 117,000 120,000 (kilometers) (173 000) (178 000) (182 000) (187 000) (192 000) inspect the drive belt and replace as needed. Not required if belt was previously replaced. X drain and refill the transfer case fluid. X flush and replace the engine coolant/anti-freeze at 1...

  • Page 314

    Schedule “a” miles 6,000 12,000 18,000 24,000 30,000 (kilometers) (10 000) (19 000) (29 000) (38 000) (48 000) [months] [6] [12] [18] [24] [30] change the engine oil and engine oil filter. X x x x x rotate the tires. X x x x x inspect the engine air filter element, and replace if necessary. X replac...

  • Page 315

    Miles 36,000 42,000 48,000 54, 000 (kilometers) (58 000) (67 000) (77 000) (86 000) [months] [36] [42] [48] [54] change the engine oil and engine oil filter. X x x x rotate the tires. X x x x lubricate the steering and suspension ball joints. X x lubricate the steering linkage joints and outer tie r...

  • Page 316

    Miles 60,000 66,000 72,000 78,000 (kilometers) (96 000) (106 000) (115 000) (125 000) [months] [60] [66] [72] [78] change the engine oil and engine oil filter. X x x x rotate the tires. X x x x inspect the engine air filter element, and replace if nec- essary. X inspect the pcv valve, and replace if...

  • Page 317

    Miles 60,000 66,000 72,000 78,000 (kilometers) (96 000) (106 000) (115 000) (125 000) [months] [60] [66] [72] [78] flush and replace the engine coolant/anti-freeze at 60 months, if not done at 102,000 miles (163 000 km). X inspect transfer case fluid. X schedule “a” 317 8 m a i n t e n a n c e s c h...

  • Page 318

    Miles 84,000 90,000 96,000 102, 000 (kilometers) (134 000) (144 000) (154 000) (163 000) [months] [84] [90] [96] [102] change the engine oil and engine oil filter. X x x x rotate the tires. X x x x inspect the engine air filter element, and replace if nec- essary. X inspect the pcv valve, and replac...

  • Page 319

    Miles 108,000 114,000 120,000 (kilometers) (173 000) (182 000) (192 000) [months] [108] [114] [120] change the engine oil and engine oil filter. X x x rotate the tires. X x x inspect the engine air filter element, and replace if necessary. X replace the ignition cables (2.4l only). X inspect the pcv...

  • Page 320

    Miles 108,000 114,000 120,000 (kilometers) (173 000) (182 000) (192 000) [months] [108] [114] [120] flush and replace the engine coolant/anti-freeze, if not done at 102,000 miles (163 000 km). X inspection and service should also be performed anytime a malfunction is observed or suspected. Retain al...

  • Page 321: Contents

    If you need consumer assistance contents 䡵 suggestions for obtaining service for your vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 322 ▫ prepare for the appointment . . . . . . . . . . . . 322 ▫ prepare a list . . . . . . . . . . . . . . . . . . . . . . . . 322 ▫ be reasonable...

  • Page 322

    Suggestions for obtaining service for your vehicle prepare for the appointment if you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty, discuss additional charges with the service manager. ...

  • Page 323

    Technicians, special tools, and the latest information to assure your vehicle is fixed correctly and in a timely manner. This is why you should always talk to your dealer’s service manager first. Most matters can be resolved with this process. • if for some reason you are still not satisfied, talk t...

  • Page 324

    Customer assistance for the hearing or speech impaired (tdd/tty) to assist customers who have hearing difficulties, the manufacturer has installed special tdd (telecommuni- cation devices for the deaf) equipment at its customer center. Any hearing or speech impaired customer who has access to a tdd ...

  • Page 325

    We appreciate that you have made a major investment when you purchased your new vehicle. Your dealer has also made a major investment in facilities, tools, and training to assure that you are absolutely delighted with your ownership experience. You’ll be pleased with their sincere efforts to resolve...

  • Page 326

    U.S. Only 326 if you need consumer assistance.

  • Page 327

    Mopar 姞 parts mopar 威 fluids, lubricants, parts, and accessories are available from your dealer. They will help you keep your vehicle operating at its best. Reporting safety defects in the 50 united states and washington d.C.: if you believe that your vehicle has a defect which could cause a crash o...

  • Page 328

    Publication order forms to order the following manuals, you may use either the website or the phone numbers listed below. Visa, mas- tercard, american express, and discover orders are ac- cepted. If you prefer mailing your payment, please call for an order form. Note: a street address is required wh...

  • Page 329

    Call toll free at 1–800–890–4038 (u.S.) or 1–800–387–1143 (canada) or visit us on the world wide web at: www.Techauthority.Daimlerchrysler.Com or www.Daimlerchrysler.Ca/manuals if you need consumer assistance 329 9.

  • Page 331: Index

    Index 10

  • Page 332

    About your brakes . . . . . . . . . . . . . . . . . . . . . . . 198 abs (anti-lock brake) system . . . . . . . . . . . . 147,200 add-a-trunk . . . . . . . . . . . . . . . . . . . . . . . . . . . 72 adding washer fluid . . . . . . . . . . . . . . . . . . . . . 138 air cleaner, engine (engine air clea...

  • Page 333

    Voltmeter . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143 belts, drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . 257 belts, seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 body mechanism lubrication . . . . . . . . . . . . . . . 264 b-pillar location . ....

  • Page 334

    Child restraint . . . . . . . . . . . . . . . . . . . . . . 34,38,41 child restraint tether anchors . . . . . . . . . . . . . 37,38 climate control . . . . . . . . . . . . . . . . . . . . . . . . . 169 clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148 clutch interlocking igni...

  • Page 335

    Dimmer switch, headlight . . . . . . . . . . . . . . . . . . 63 dipsticks oil (engine) . . . . . . . . . . . . . . . . . . . . . . . . . . 253 disabled vehicle towing . . . . . . . . . . . . . . . . . . . 244 disposal engine oil . . . . . . . . . . . . . . . . . . . . . . . . . . . 257 used coolant ...

  • Page 336

    Oil filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . 257 oil pressure gauge . . . . . . . . . . . . . . . . . . . . . 145 oil selection . . . . . . . . . . . . . . . . . . . . . . . . . . 295 overheating . . . . . . . . . . . . . . . . . . . . . . . . . . 237 starting . . . . . . . . ....

  • Page 337

    Front axle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 278 fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 222 filler cap . . . . . . . . . . . . . . . . . . . . . . . . . . . . 226 filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260 gasoline...

  • Page 338

    Heater, engine block . . . . . . . . . . . . . . . . . . . . . 180 high beam indicator . . . . . . . . . . . . . . . . . . . . . 144 holder, cup . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 hood release . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 hoses . . . . . . . . . . ...

  • Page 339

    Lead free gasoline . . . . . . . . . . . . . . . . . . . . . . 222 lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 airbag . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33,145 anti-lock . . . . . . . . . . . . . . . . . . . . . . . . . . . 147 anti-lock warning ....

  • Page 340

    Lower anchors and tether for children (latch) . . . . . . . . . . . . . . . . . . . . . . . . . . . 37,38 lubrication, body . . . . . . . . . . . . . . . . . . . . . . . 264 maintenance, airbag . . . . . . . . . . . . . . . . . . . . . . 33 maintenance free battery . . . . . . . . . . . . . . . . . ...

  • Page 341

    Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 257 identification logo . . . . . . . . . . . . . . . . . . . . . 255 materials added to . . . . . . . . . . . . . . . . . . . . . 257 recommendation . . . . . . . . . . . . . . . . . . . 255,295 viscosity . . . . . . . . . . . . ....

  • Page 342

    Recommended fluids, lubricants and genuine parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 296 recreational towing . . . . . . . . . . . . . . . . . . . . . . 232 shifting into transfer case neutral (n) . . . . . . . 232 shifting out of transfer case neutral (n) . . . . . 233 ref...

  • Page 343

    Tilting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 selection of oil . . . . . . . . . . . . . . . . . . . . . . . . . 255 sentry key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 sentry key programming . . . . . . . . . . . . . . . . . . . 16 sentry key replaceme...

  • Page 344

    Storage, vehicle . . . . . . . . . . . . . . . . . . . . . . . . . 290 storing your vehicle . . . . . . . . . . . . . . . . . . . . . . 290 supplemental restraint system - airbag . . . . . . . . 27 tachometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143 temperature gauge, engine coola...

  • Page 345

    Hitches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 222 transfer case . . . . . . . . . . . . . . . . . . . . . . . . . . . 277 four-wheel-drive operation . . . . . . . . . . . . . . 191 maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . 277 transmission automatic . . . . ...

  • Page 346

    Windshield, folding . . . . . . . . . . . . . . . . . . . . . . 130 windshield washers . . . . . . . . . . . . . . . . . . . . 64,265 fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 265 windshield wiper blades . . . . . . . . . . . . . . . . . . 265 windshield wipers . . . . . . ...

  • Page 347: Notes

    Notes.

  • Page 348: Notes

    Notes.

  • Page 349: Notes

    Notes.

  • Page 350: Notes

    Notes.

  • Page 351: Notes

    Notes.

  • Page 352: Notes

    Notes.