1. DL manuals
  2. Jeep
  3. Automobile
  4. 2006 commander
  5. Owner's Manual

Jeep 2006 commander Owner's Manual

Manual is about: Chrysler LLC

Summary of 2006 commander

  • Page 1

    Table of contents section page 1 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 things to know before starting your vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 3 understanding the fea...

  • Page 3: Introduction

    Introduction contents 䡵 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 ▫ roll over warning . . . . . . . . . . . . . . . . . . . . . 5 䡵 how to use this manual . . . . . . . . . . . . . . . . . . 7 䡵 warnings and cautions . . . . . . . . . . . . . . . . . . . 7 䡵 vehicle identi...

  • Page 4

    Introduction thank you for selecting a jeep 威 commander and wel- come to our worldwide family. This is a specialized utility vehicle designed for both on-road and off-road use. It can go places and perform tasks for which conventional two-wheel drive vehicles were not intended. However, on-road ride...

  • Page 5

    Roll over warning utility vehicles have a significantly higher roll over rate than other types of vehicles. This vehicle has a higher ground clearance, higher center of gravity, and narrower track than many passenger cars. It is capable of perform- ing better in a wide variety of off-road applicatio...

  • Page 6

    Failure to use driver and passenger seat belts provided is a major cause of severe or fatal injury. In fact, the u.S. Government notes that the universal use of existing seat belts could cut the highway death toll by 10,000 or more each year, and could reduce disabling injuries by 2 million annually...

  • Page 7

    Warning! Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the state of california to cause cancer and birth defects or other reproductive harm. In addition, certain fluids contained in vehicles and certain prod- ucts of component wear contai...

  • Page 8

    Vehicle identification number the vehicle identification number (vin) is found on a label located on the left front corner of the instrument panel pad, visible from outside of the vehicle through the windshield. This number also appears on the automobile information disclosure label affixed to a win...

  • Page 9

    Vehicle modifications / alterations warning! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death. Introduction 9 1.

  • Page 11: Contents

    Things to know before starting your vehicle contents 䡵 a word about your keys . . . . . . . . . . . . . . . . . .14 ▫ ignition key . . . . . . . . . . . . . . . . . . . . . . . . . .14 ▫ key-in-ignition reminder . . . . . . . . . . . . . . . .15 䡵 sentry key immobilizer system . . . . . . . . . . . ...

  • Page 12

    ▫ transmitter battery service . . . . . . . . . . . . . . .24 䡵 security alarm system — if equipped . . . . . . . . .25 ▫ to set the alarm . . . . . . . . . . . . . . . . . . . . . .26 ▫ to disarm the system . . . . . . . . . . . . . . . . . . .26 䡵 liftgate . . . . . . . . . . . . . . . . . . . . ....

  • Page 13

    䡵 safety tips . . . . . . . . . . . . . . . . . . . . . . . . . . . .69 ▫ exhaust gas . . . . . . . . . . . . . . . . . . . . . . . . . .69 ▫ safety checks you should make inside the vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70 ▫ safety checks you should make outside the veh...

  • Page 14

    A word about your keys the keys for your new vehicle are enclosed in a plastic bag with the key code number on it. If you received your keys without the bag, ask your authorized dealer to give you the number. The key code can also be obtained by your authorized dealer from your vehicle invoice. Igni...

  • Page 15

    Key-in-ignition reminder if the driver’s door is opened when the key is in the ignition and not turned to the on position, a chime will sound to remind you to remove the key. Caution! Always remove the key from the ignition, and lock all doors when leaving the vehicle unattended. Sentry key immobili...

  • Page 16

    If the skim indicator light comes on during normal vehicle operation (it has been running for longer than 10 seconds) a fault has been detected in the electronics and the vehicle should be serviced as soon as possible. Note: • the sentry key immobilizer system is not compatible with remote starting ...

  • Page 17

    Consists of programming a blank key to the vehicle electronics. A blank key is one which has never been programmed. Note: when having the sentry key system serviced, bring all vehicle keys to the dealer. Customer key programming you can program new keys to the system if you have two valid keys by do...

  • Page 18

    2. This device must accept any interference that may be received, including interference that may cause undes- ired operation. Illuminated entry the interior lights come on when you open any door. They will remain on for about 30 seconds after all doors are closed then fade to off. The lights also w...

  • Page 19

    Caution! An unlocked vehicle is an invitation to thieves. Always remove the key from the ignition and lock all of the doors when leaving the vehicle unattended. Child protection locks the rear doors of your vehicle are equipped with child protection locks. If you push up on the lever on the open edg...

  • Page 20

    Power door locks a door lock switch is on each front door panel. Press this switch to lock or unlock the doors. If the plunger is down when the door is closed, the door will lock. Therefore, make sure the keys are not inside the vehicle before closing the door. If you press the door lock switch whil...

  • Page 21

    Automatic unlock on exit feature — only available if auto lock is enabled this feature will unlock all the doors when the driver’s door is opened if the vehicle is stopped and in p (park) or n (neutral). Refer to “electronic vehicle information center (evic) — customer programmable features” in sect...

  • Page 22

    Note: if desired, the system can be programmed to unlock all doors on the first press of the “unlock” button. Refer to “remote unlock driver’s door 1st” in the personal settings section of the “electronic vehicle infor- mation center (evic)”, or simply follow these steps: 1. Press and hold the “lock...

  • Page 23

    Warning! Driving with the flipper glass open can allow poi- sonous exhaust gases into your vehicle. You and your passengers could be injured by these fumes. Keep the flipper glass closed when you are operating the vehicle. Using the panic alarm to turn the panic alarm feature on or off, press and ho...

  • Page 24

    2. While the “unlock” button is pressed, (after 4 seconds) press the “lock” button. Release both buttons. The “flash lights on lock/unlock” feature can be reactivated by repeating this procedure. General information this device complies with part 15 of the fcc rules and rss 210 of industry canada. O...

  • Page 25

    2. Remove and replace the battery. Avoid touching the new battery with your fingers. Skin oils may cause battery deterioration. If you touch a battery, clean it with rubbing alcohol. 3. To reassemble the transmitter case, join the two halves of the case together. Install and tighten the screw until ...

  • Page 26

    To set the alarm the alarm will set when you use the remote keyless entry transmitter to lock the doors and liftgate or when you use the power door lock switch while the door is open. After all the doors are locked and closed, a red light (located in the instrument cluster) will flash rapidly for ab...

  • Page 27

    Liftgate to open the liftgate, pull up (squeeze) on the handle and lift. Manually unlocking the vehicle doors with the plunger or a key in the lock cylinder will not unlock the liftgate. Warning! Driving with the liftgate open can allow poisonous exhaust gases into your vehicle. You and your pas- se...

  • Page 28

    Liftgate flipper glass the liftgate flipper glass is also unlocked when the liftgate is unlocked. To open the flipper glass, push up on the window switch located on the liftgate. Warning! To avoid injury stand back when opening. Glass will automatically rise. Once the liftgate flipper glass has been...

  • Page 29

    Power windows the power window controls are located on the driver’s door trim panel. There is a single switch on the front passenger door/rear doors which operates the front passenger/rear passenger door windows. The window controls will operate only when the ignition switch is in the on or accessor...

  • Page 30

    Auto down both the driver and front passenger window switch has an “auto down” feature. Press the window switch past the first detent, release, and the window will go down automatically. To cancel the “auto down” movement, operate the switch in either the up or down direction and release the switch....

  • Page 31

    Warning! There is no anti-pinch protection when the window is almost closed. Be sure to clear all objects from the window before closing. Resetting the auto-up feature should the auto-up feature stop working the window probably needs to be reset. To reset auto-up: pull the window switch up and close...

  • Page 32

    Open or partially open positions. This is a normal occur- rence and can be minimized. If the buffeting occurs with the sunroof open, adjust the sunroof opening to minimize the buffeting. Occupant restraints some of the most important safety features in your vehicle are the restraint systems. These i...

  • Page 33

    Research has shown that seat belts save lives, and they can reduce the seriousness of injuries in a collision. Some of the worst injuries happen when people are thrown from the vehicle. Seat belts reduce the possibility of ejection and the risk of injury caused by striking the inside of the vehicle....

  • Page 34

    Lap/shoulder belt operating instructions 1. Enter the vehicle and close the door. Sit back and adjust the seat. 2. The seat belt latch plate is above the back of your seat. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to make the belt go aroun...

  • Page 35

    3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” warning! A belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt ...

  • Page 36

    4. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap portion, pull up a bit on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision. Wa...

  • Page 37

    6. To release the belt, push the red button marked press on the buckle. The belt will automatically retract to its stowed position. If necessary, slide the latch plate down the webbing to allow it to retract fully. Warning! A frayed or torn belt could rip apart in a collision and leave you with no p...

  • Page 38

    As a guide, if you are shorter than average, you will prefer a lower position, and if you are taller than average, you’ll prefer a higher position. When you release the anchorage, try to move it up or down to make sure that it is locked in position. Automatic locking mode — if equipped in this mode,...

  • Page 39

    This safety belt system has a retractor assembly that is designed to release webbing in a controlled manner. This feature is designed to help reduce the belt force acting on the occupant’s chest. Warning! • the belt and retractor assembly must be replaced if the seat belt assembly “automatic locking...

  • Page 40

    Enhanced seat belt use reminder system (beltalert) if the driver or front passenger seat belt has not been buckled within 60 seconds of starting the vehicle and if the vehicle speed is greater than 5 mph (8 km/h), the enhanced warning system (beltalert) will alert the driver or front passenger to bu...

  • Page 41

    The enhanced warning system (beltalert) can be reacti- vated by repeating this procedure. Note: although the enhanced warning system (beltalert) has been deactivated, the seat belt warning light will continue to illuminate while the driver or front passenger seat belt remains unfastened. Seat belts ...

  • Page 42

    Driver and front passenger supplemental restraint systems (srs) this vehicle has airbags for both the driver and right front passenger as a supplement to the seat belt restraint systems. The driver’s front airbag is mounted in the steering wheel. The passenger side airbag is mounted in the instrumen...

  • Page 43

    This vehicle also is equipped with window bags to protect the driver, front, and rear passengers sitting next to a window. They are located above the side windows. Their covers are also labeled srs/airbag. Note: airbag covers may not be obvious in the interior trim; but they will open to allow airba...

  • Page 44

    The front airbags have a multi stage inflator design. This allows the airbag to have different rates of inflation that are based on collision severity. Along with the seat belts, front airbags work with the instrument panel knee bol- sters to provide improved protection for the driver and front pass...

  • Page 45

    Children that are not big enough to properly wear the vehicle seat belt should be secured in the rear seat, in a child restraint or belt-positioning booster seat. Older children who do not use child restraints or belt- positioning booster seats should ride properly buckled up in the rear seat. Never...

  • Page 46

    Warning! • relying on the airbags alone could lead to more severe injuries in a collision. The airbags work with your seat belt to restrain you properly. In some collisions the airbags won’t deploy at all. Always wear your seat belts even though you have airbags. • being too close to the steering wh...

  • Page 47

    • driver and front passenger seat belt pretensioner • occupant classification system (ocs) — front pas- senger seat only − occupant classification module − passenger airbag disable (pad) indicator light − weight sensors how the airbag system works • the occupant restraint control (orc) module de- te...

  • Page 48

    Warning! Ignoring the “airbag warning light” in your instru- ment panel could mean you won’t have the airbags to protect you in a collision. If the light does not come on, stays on after you start the vehicle, or if it comes on as you drive, have the airbag system checked right away. • the occupant ...

  • Page 49

    The “pad indicator light” should not be illuminated when teenagers, most children in a forward-facing child restraint or booster seats, most children that can properly wear the vehicle’s seat belt, and when an adult passenger is properly seated in the front passen- ger seat. In this case, the airbag...

  • Page 50

    Front passenger seat occupant passenger air- bag disable (pad) indicator light airbag status adult off on grocery bags, heavy briefcases and other rela- tively light ob- jects on off empty or very small objects off* off * since the system senses weight, some small objects will turn the pad indicator...

  • Page 51

    Because this can also affect occupant classification. Also, if you fold down the rear seat check to be sure it doesn’t touch the front passenger seat. If the front passenger seat is damaged in any way, it should only be serviced by an authorized dealer. If the seat is removed (or even if the seat at...

  • Page 52

    The driver front airbag gas is vented through the vent holes in the sides of the airbag. The passenger front airbag gas is vented through the vent holes in the sides of the airbag. In this way, the airbags do not interfere with your control of the vehicle. • the occupant classification module (ocm) ...

  • Page 53

    The front passenger seat assembly contains critical com- ponents that affect the front passenger airbag deploy- ment. Correctly functioning front passenger seat compo- nents are critical for the occupant classification system (ocs) to properly classify the front passenger and calcu- late the proper ...

  • Page 54

    Warning! Unapproved modifications or service procedures to the front passenger seat assembly, its related compo- nents, or seat cover may inadvertently change the airbag deployment in case of a frontal crash. This could result in death or serious injury to the front seat passenger if the vehicle is ...

  • Page 55

    • as the airbags deflate you may see some smoke-like particles. The particles are a normal by-product of the process that generates the nontoxic gas used for airbag inflation. These airborne particles may irritate the skin, eyes, nose, or throat. If you have skin or eye irritation, rinse the area wi...

  • Page 56

    Maintaining your airbag system warning! • modifications to any part of the airbag system could cause it to fail when you need it. You could be injured if the airbag system is not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the stee...

  • Page 57

    With other data gathered during a complete accident investigation, the electronic data may be used by daimlerchrysler corporation and others to learn more about the possible causes of crashes and associated injuries in order to assess and improve vehicle perfor- mance. In addition to crash investiga...

  • Page 58

    Data parameters that may be recorded: • diagnostic trouble code(s) and warning lamp status for electronically-controlled safety systems, including the airbag system • airbag disable lamp status (if equipped) • ⬙time⬙ of airbag deployment (in terms of ignition cycles and vehicle mileage) • airbag dep...

  • Page 59

    Warning! In a collision, an unrestrained child, even a tiny baby, can become a missile inside the vehicle. The force required to hold even an infant on your lap can become so great that you could not hold the child, no matter how strong you are. The child and others could be badly injured. Any child...

  • Page 60

    Warning! • improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the manufacturer’s directions ex- actly when installing an infant or child restraint. • a rearward facing infant restraint shou...

  • Page 61

    Belt tight, however, any seat belt system will loosen with time, so check the belt occasionally and pull it tight if necessary). For the second and third row seat belts with the automatic locking retractor, pull the belt from the retractor until there is enough to allow you to pass through the child...

  • Page 62

    Older children and child restraints children who weigh more than 20 lbs (9 kg) and who are older than one year can ride forward-facing in the vehicle. Forward-facing child seats and convertible child seats used in the forward-facing direction, are for chil- dren who weigh 20 to 40 lbs (9 to 18 kg), ...

  • Page 63

    Latch — child seat anchorage system (lower anchors and tether for ch ildren) your vehicle’s second row seat is equipped with the child restraint anchorage system called latch. The latch system provides for the installation of the child restraint without using the vehicle’s seat belts, instead securi...

  • Page 64

    The second row outboard seating positions have lower anchorages that are capable of accommodating latch- compatible child seats having flexible, webbing-mounted lower attachments. Child seats with fixed lower attach- ments must be installed in the outboard positions only. Regardless of the specific ...

  • Page 65

    In addition, there are tether strap anchorages behind each rear outboard seating position located on the back of the seat. Many, but not all restraint systems will be equipped with separate straps on each side, with each having a hook or connector for attachment to the lower anchorage and a means of...

  • Page 66

    Hook for attachment to the tether strap anchorage and a means of adjusting the tension of the strap. You will first loosen the adjusters on the lower straps and on the tether strap so that you can more easily attach the hooks or connectors to the vehicle anchorages. Next attach the lower hooks or co...

  • Page 67

    If the seat belt has a automatic locking retractor, it will have a distinctive label. Pull the belt from the retractor until there is enough to allow you to pass through the child restraint and slide the latch plate into the buckle. Then, pull the belt until it is all extracted from the retractor. A...

  • Page 68

    Route the tether strap over the seat back and attach the hook to the tether anchor located on the back of the seat. For the outboard seating positions, route the tether over the head rests, and attach the hook to the tether anchor located on the back of the seat. Warning! An incorrectly anchored tet...

  • Page 69

    The engine oil installed in the engine at the factory is a high quality energy conserving type lubricant. Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur. The recommended viscosity and quality grades are shown in section 7 of this manual...

  • Page 70

    • do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas which can kill. Never run the engine in a closed area, such as a garage, and never sit in a parked vehicle with the engine running for a extended period. If the vehicle is stopped in an open area with engine ru...

  • Page 71

    Defrosters check operation by selecting the defrost mode and place the blower control on high speed. You should feel the air directed against the windshield. Safety checks you should make outside the vehicle tires examine tires for excessive tread wear or uneven wear patterns. Check for stones, nail...

  • Page 73: Contents

    Understanding the features of your vehicle contents 䡵 mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78 ▫ inside day/night mirror . . . . . . . . . . . . . . . . .78 ▫ inside automatic dimming mirror — if equipped . . . . . . . . . . . . . . . . . . . . . . . . . .79 ▫ exterior...

  • Page 74

    ▫ front seat adjustment — recline . . . . . . . . . . 106 ▫ manual lumbar support adjustment . . . . . . . 106 ▫ head restraints . . . . . . . . . . . . . . . . . . . . . . 107 ▫ 8 - way driver’s power seat . . . . . . . . . . . . . . 108 ▫ 4 - way passenger’s power seat — if equipped . . . . . . . ...

  • Page 75

    ▫ lights-on reminder . . . . . . . . . . . . . . . . . . . 125 ▫ fog lights — if equipped . . . . . . . . . . . . . . . 126 ▫ turn signals . . . . . . . . . . . . . . . . . . . . . . . . . 126 ▫ high beam switch . . . . . . . . . . . . . . . . . . . . 126 ▫ passing light . . . . . . . . . . . . . . ...

  • Page 76

    䡵 electronic speed control . . . . . . . . . . . . . . . . . . 148 ▫ to activate . . . . . . . . . . . . . . . . . . . . . . . . . . 149 ▫ to set at a desired speed . . . . . . . . . . . . . . . 149 ▫ to deactivate . . . . . . . . . . . . . . . . . . . . . . . . 149 ▫ to resume speed . . . . . . . ....

  • Page 77

    ▫ sunroof fully closed . . . . . . . . . . . . . . . . . . . 161 䡵 command-view™ skylights — if equipped . . . . 161 䡵 power outlet . . . . . . . . . . . . . . . . . . . . . . . . . . 162 䡵 cup holders . . . . . . . . . . . . . . . . . . . . . . . . . . 164 䡵 cargo area features . . . . . . . . . . ...

  • Page 78

    Mirrors inside day/night mirror the mirror should be adjusted to center on the view through the rear window. A two-point pivot system allows for horizontal and vertical adjustment of the mirror. The mirror should be adjusted while set in the day position (toward windshield). Annoying headlight glare...

  • Page 79

    Inside automatic dimming mirror — if equipped this mirror automatically adjusts for annoying headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light next to the button will indicate when the dimming feature is activated. ...

  • Page 80

    Exterior mirrors folding feature all exterior mirrors are hinged and may be moved either forward or rearward to resist damage. The hinges have three detent positions; full forward, full rearward, and normal. Outside mirrors to receive maximum benefit, adjust the outside mirrors to center on the adja...

  • Page 81

    Power remote control outside mirrors the power mirror switch is located on the driver’s door trim panel next to the power door lock switch. A rotary knob selects the left mirror, right mirror, or off position. After selecting a mirror move the knob in the same direction you want the mirror to move. ...

  • Page 82

    Lighted vanity mirrors — if equipped to access a lighted vanity mirror, flip down one of the visors. Lift the cover to reveal the mirror. The light will turn on automatically. Sun visor extension this feature has a pull out extension on the sun visor for increased coverage. Hands–free communication ...

  • Page 83

    Uconnect™ allows you to transfer calls between the system and your cellular phone as you enter or exit your vehicle, and enables you to mute the system’s micro- phone for private conversation. The uconnect™ phonebook enables you to store up to 32 names and four numbers per name. Each language has a ...

  • Page 84

    The uconnect™ system can be used with any hands- free profile certified bluetooth™ cellular phone. See www.Chrysler.Com/uconnect for supported phones. If your cellular phone supports a different profile (e.G., headset profile), you may not be able to use any ucon- nect™ features. Refer to your cellu...

  • Page 85

    Example, you can either use the combined form voice command ⬙phonebook new entry,⬙ or you can break the combined form command into two voice com- mands: ⬙phonebook⬙ and ⬙new entry.⬙ please remem- ber, the uconnect™ system works best when you talk in a normal conversational tone, as if speaking to so...

  • Page 86

    Note: • www.Chrysler.Com/uconnect • www.Dodge.Com/uconnect • www.Jeep.Com/uconnect the following are general phone to uconnect™ system pairing instructions: • press the ’phone’ button to begin. • after the ⬙ready⬙ prompt and the following beep, say ⬙setup phone pairing.⬙ • when prompted, after the v...

  • Page 87

    Phones are present in the vehicle, the uconnect™ system will use the priority 3 cellular phone when you make a call. You can select to use a lower priority cellular phone at any time (refer to ⬙advanced phone connectivity ⬙). Dial by saying a number • press the ’phone’ button to begin. • after the ⬙...

  • Page 88

    • after the ⬙ready⬙ prompt and the following beep, say the name of the person you want to call. For example, you can say ⬙john doe,⬙ where john doe is a previ- ously stored name entry in the uconnect™ phone- book. Refer to ⬙add names to your uconnect™ phonebook, ⬙ to learn how to store a name in the...

  • Page 89

    Four associated phone numbers and designations. Each language has a separate 32 name phonebook accessible only in that language. Edit entries in the uconnect™ phonebook note: editing phonebook entries is recommended when vehicle is not in motion. • press the ’phone’ button to begin. • after the ⬙rea...

  • Page 90

    • after you enter the phonebook delete menu, you will then be asked for the name of the entry that you wish to delete. You can either say the name of a phonebook entry that you wish to delete or you can say ⬙list names ⬙ to hear a list of the entries in the phonebook from which you choose. To select...

  • Page 91

    • to call one of the names in the list, press the ⬙voice recognition’ button during the playing of the desired name and say ⬙call.⬙ note: the user can also exercise ⬙edit⬙ or ⬙delete⬙ operations at this point. • the uconnect™ system will then prompt you as to number designation you wish to call. • t...

  • Page 92

    Making a second call while current call in progress to make a second call while you are currently in a call, press the ’voice recognition’ button and say ⬙dial⬙ or ⬙call⬙ followed by the phone number or phonebook entry you wish to call. The first call will be on hold while the second call is in prog...

  • Page 93

    Call termination to end a call in progress, momentarily press the ⬘phone’ button. Only the active call(s) will be terminated and if there is a call on hold, it will become the new active call. Redial • press the ’phone’ button to begin. • after the ⬙ready⬙ prompt and the following beep, say ⬙redial....

  • Page 94

    • after the ⬙ready⬙ prompt and the following beep, say the name of the language you wish to switch to (english, espanol, or francais, if so equipped). • continue to follow the system prompts to complete language selection. After selecting one of the languages, all prompts and voice commands will be ...

  • Page 95

    Your phone must be turned on and paired to the ucon- nect™ system to allow use of this vehicle feature in emergency situations when the cell phone has network coverage and stays paired to the uconnect™ system. Towing assistance if you need towing assistance, • press the ’phone’ button to begin. • af...

  • Page 96

    When calling a number with your uconnect™ system that normally requires you to enter in a touch-tone sequence on your cellular phone keypad, you can push the ’voice recognition’ button and say the sequence you wish to enter followed by the word ⬙send.⬙ for example, if required to enter your pin numb...

  • Page 97

    Dialing using the cellular phone keypad you can dial a phone number with your cellular phone keypad and still use the uconnect™ system (while dialing via the cell phone keypad, the user must exercise caution and take precautionary safety measures). By dialing a number with your paired bluetooth™ cel...

  • Page 98

    Information service when using at&t wireless service, dialing to phone number ⬙#121,⬙ you can access voice activated automated system to receive news, weather, stocks, traffic, etc. Related information. Advanced phone connectivity transfer call to and from cellular phone the uconnect™ system allows ...

  • Page 99

    Select another cellular phone this feature allows you to select and start using another phone with the uconnect™ system. The phone must have been previously paired to the uconnect™ system that you want to use it with. • press the ’phone’ button to begin. • after the ⬙ready⬙ prompt and the following ...

  • Page 100

    Things you should know about your uconnect™ system voice recognition (vr) • always wait for the beep before speaking. • speak normally, without pausing, just as you would speak to a person sitting approximately eight (8) feet away from you. • make sure that no one other than you is speaking during a...

  • Page 101

    • you can say ⬙o⬙ (letter ⬙o⬙) for ⬙0⬙ (zero). ⬙800⬙ must be spoken ⬙eight-zero-zero.⬙ • even though international dialing for most number combinations is supported, some shortcut dialing number combinations may not be supported. Far end audio performance • audio quality is maximized under: • low-to...

  • Page 102

    102 understanding the features of your vehicle.

  • Page 103

    Understanding the features of your vehicle 103 3.

  • Page 104

    104 understanding the features of your vehicle.

  • Page 105

    North american english primary alternate(s) zero oh add location add new all all of them confirmation prompts confirmations prompts delete a name delete language select language list names list all list paired phones list phones pager beeper phone pairing pairing phonebook phone book return to main ...

  • Page 106

    Front seat adjustment — recline to adjust the seatback, lift the lever located on the outboard side of the seat, lean back, and release the lever at the desired position. To return the seatback, lift the lever, lean forward, and release the lever. Warning! Do not ride with the seatback reclined so t...

  • Page 107

    Head restraints head restraints can reduce the risk of whiplash injury in the event of impact from the rear. Adjustable head restraints should be adjusted so that the upper edge is as high as practical. The head restraints have a locking button which must be pushed in to lower the head restraint to ...

  • Page 108

    8 - way driver’s power seat the driver’s power seat switches are located on the outboard side of the driver’s seat lower side trim. The bottom switch controls up/down, forward/rearward, and tilt adjustment. The top switch controls the seatback recline adjustment. 4 - way passenger’s power seat — if ...

  • Page 109

    Indicate the level of heat in use. Two leds are illumi- nated for high, one for low, and none for off. Pressing the switch once will select high-level heating. Pressing the switch a second time will select low-level heating. Pressing the switch a third time will shut the heating elements off. When h...

  • Page 110

    1. Pull up on the seatback lever located on the outboard side of the seat. Note: also, pulling upward on this handle allows the outboard seating positions to be reclined. 2. Fold the seatback down, and tumble the seat forward. Warning! Do not drive the vehicle with the outer second row seats in the ...

  • Page 111

    Note: if sitting in the third row seat, pull rearward on the release strap located at the rear of the seat and tumble the seat forward. Fold and tumble seat release strap understanding the features of your vehicle 111 3.

  • Page 112

    Folding middle seatback (second row seat) 1. Pull the release strap. 2. Lower the center seatback. Center seat armrest (second row seat) — if equipped the second row center seat may be equipped with a armrest. Pull strap to lower armrest. Release strap folding center seatback 112 understanding the f...

  • Page 113

    50/50 third row folding seat to lower rear seat either side of the third row seat can be lowered to allow for extended cargo space, and still maintain some rear seating room. 1. Open the tailgate. 2. Push the seatback release handle (toward rear of vehicle), and lower the seatback using the pull str...

  • Page 114

    To raise rear seat 1. Open the tailgate. 2. Detach pull strap from back of seat, and pull seatback upward until it locks into place. Reattach strap. 3. Raise the head restraints. 4. Close the tailgate. Warning! The cargo area in the rear of the vehicle (with the rear seatbacks in the locked-up or fo...

  • Page 115

    Your vehicle may have been delivered with two remote keyless entry transmitters. One or both transmitters can be linked to either memory position. The memory system can accommodate up to four transmitters, each one linked to either of the two memory positions. Setting memory positions and linking re...

  • Page 116

    5. Turn on the radio and set the radio station presets (up to 10 am and 10 fm stations can be set). 6. Turn the ignition switch to the off position and remove the key. 7. Press and release the set (s) button located on the driver’s door. 8. Within 5 seconds, press and release memory button 1 or 2 on...

  • Page 117

    To recall the memory settings for driver one, press memory button number 1 on the driver’s door or the “unlock” button on the remote keyless entry transmit- ter linked to memory position 1. To recall the memory setting for driver two, press memory button number 2 on the driver’s door or the “unlock”...

  • Page 118

    Note: once programmed, all transmitters linked to memory can be easily enabled or disabled at one time. Refer to remote linked to memory under ⬙electronic vehicle information center (evic) — customer pro- grammable features ⬙ in section 4 for more information. Easy entry/exit seat this feature provi...

  • Page 119

    Note: the easy entry easy exit feature is not enabled when the vehicle is delivered from the factory. The easy entry easy exit feature is enabled (or later disabled) through the programmable features in the electronic vehicle information center (evic). Refer to ⬙electronic vehicle information center...

  • Page 120

    Then, reach under the hood, move safety latch to the left, and lift the hood. To prevent possible damage, do not slam the hood to close it. Use a firm downward push at the center of the hood to ensure that both latches engage. Warning! If the hood is not fully latched, it could fly up when the vehic...

  • Page 121

    Courtesy/reading lights each light can be turned on by pressing the recessed area of the lens. To turn these lights off, press the recessed area of the lens a second time. There are also reading lights located above the rear doors. Each light can be turned on by pressing the front recessed area of t...

  • Page 122

    Multi-function control lever the multi-function control lever controls the operation of the headlights, turn signals, headlight beam selection, instrument panel light dimming, passing light, interior courtesy/dome lights, and optional fog lights. Turn signal auto-mode — if equipped tap the multi-fun...

  • Page 123

    Automatic headlight system — if equipped turn the end of the multi-function control lever to the third detent to activate the automatic headlight system. This system performs two functions. With the engine running and the multi-function control lever in the a (auto) position, the headlights will tur...

  • Page 124

    Note: when your headlights come on during the daytime, the instrument panel lights will automatically dim to the lower nighttime intensity. Refer to “instru- ment panel and interior lights” below for setting the instrument panel lights to full daytime intensity. Smartbeams — if equipped the smartbea...

  • Page 125

    Headlights to remain on longer (closer to the vehicle). Also, dirt, film, and other obstructions (sticker, toll box, etc.) on the windshield or camera lens will cause the system to function improperly. Instrument panel and interior lights when the multi-function control lever is in the parklight, he...

  • Page 126

    Fog lights — if equipped the fog light switch is located in the multi- function control lever. To activate the fog lights, turn on the park/turn lights, low beam headlights, or “auto” headlights and pull out the end of the multi- function control lever. A light in the instrument cluster shows when t...

  • Page 127

    Headlight time delay there is also a feature that delays turning off the vehicle lights for 30, 60, or 90 seconds after the ignition switch is turned off. To activate the headlight delay, the multi- function control lever must be rotated to the “off” position after the ignition switch is turned off....

  • Page 128

    To use the washer, pull the lever toward you and hold while spray is desired. If the lever is pulled while in the delay range, the wiper will operate for several seconds after the lever is released, and then resume the intermit- tent interval previously selected. If the lever is pulled while in the ...

  • Page 129

    Rain sensing wipers—if equipped this feature senses moisture on the windshield and automatically activates the wipers for the driver. The feature is especially useful for road splash or overspray from the windshield washers of the vehicle ahead. Rotate the end of the multi-function lever to one of f...

  • Page 130

    Driver desires more sensitivity. Place the wiper switch in the off position when not using the system. Note: • the rain sensing feature will not operate when the wiper switch is in the low or high speed position. • the rain sensing feature may not function properly when ice, or dried salt water is p...

  • Page 131

    Tilt steering column to tilt the column, push down on the lever below the turn signal control and move the wheel up or down, as desired. Pull the lever back towards you and firmly push the lever until it is above the lower surface of the shroud to lock the column in place. Warning! Tilting the steer...

  • Page 132

    Abs (anti-lock brake system) this system aids the driver in maintaining vehicle control under adverse braking conditions. The system controls hydraulic brake pressure to prevent wheel lock-up and help avoid skidding on slippery surfaces during braking. Refer to “anti-lock brake system” in section 5 ...

  • Page 133

    Tcs (traction control system) this system monitors the amount of wheel spin of each of the driven wheels. If wheel spin is detected, brake pressure is applied to the slipping wheel(s) and engine power is reduced to provide enhanced acceleration and stability. A feature of the tcs system functions si...

  • Page 134

    Warning! Bas (brake assist system) cannot prevent the natu- ral laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions. Bas cannot prevent accidents, in- cluding those resulting from excessive speed in turns, driving on very slippery surfa...

  • Page 135

    Note: anytime the esp system is in the “full off” mode, erm is disabled. Refer to esp (electronic stability program) for a complete explanation of the available esp modes. Warning! Many factors, such as vehicle loading, road condi- tions and driving conditions, influence the chance that wheel lift o...

  • Page 136

    • understeer - when the vehicle is turning less than appropriate for the steering wheel position. The ⬙esp/tcs indicator light⬙ located in the instrument cluster, starts to flash as soon as the tires lose traction and the esp system becomes active. The ⬙esp/tcs indicator light ⬙ also flashes when tc...

  • Page 137

    High range (4wd models) or 2wd models on this is the normal operating mode for esp in 4wd high range and in 2wd vehicles. Whenever the vehicle is started or the transfer case (if equipped) is shifted from 4wd low range or neutral back to 4wd high range, the esp system will be in this mode. This mode...

  • Page 138

    Note: to improve the vehicle’s traction when driving with snow chains, or starting off in deep snow, sand, or gravel, it may be desirable to switch to the “partial off” mode by pressing the esp switch. Once the situation requiring esp to be switched to the “partial off” mode is overcome, turn esp ba...

  • Page 139

    Warning! With the esp switched off, the enhanced vehicle stability offered by esp and erm are unavailable. In an emergency evasive maneuver, the esp and erm systems will not engage to assist in maintaining stability. The “full off” esp mode is intended for off-highway or off-road use only. 4wd low r...

  • Page 140

    Electronic vehicle information center (evic). Refer to “electronic vehicle information center (evic)” in sec- tion 4 of this manual. (see page 186 for more informa- tion.) to turn esp on again, momentarily depress the “esp control switch”. This will restore the normal “par- tial off” mode of operati...

  • Page 141

    If the “esp/bas warning lamp” comes on continuously with the engine running, a mal- function has been detected in either the esp or the bas system, or both. If this light remains on after several ignition cycles, and the vehicle has been driven several miles at speeds greater than 30 mph (48 km/h), ...

  • Page 142

    Rear park assist sensors the four rear park assist sensors, located in the rear fascia, monitor the area behind the vehicle that is within the sensors’ field of view. The monitored area seems oval in shape. The sensors can detect obstacles from approximately 11.8 inches (30 cm) up to 59 inches (150 ...

  • Page 143

    When the obstacle is detected at a distance of about 59 inches (150 cm) from the rear fascia, the outermost leds of the warning display will be on with increased bright- ness. Along with the led, a half second tone will occur. As the distance of the detected obstacle to the rear fascia decreases, mo...

  • Page 144

    Enable/disable the rear park assist system the rear park assist system can be enabled and disabled with a switch located in the switch bank of the instru- ment panel. When the switch is pressed to disable the system, the instrument cluster will display the ⬙park assist dis- abled ⬙ message. Refer to...

  • Page 145

    Service the rear park assist system when the rear park assist system is defective, the instrument cluster will actuate a single chime, once per ignition cycle, and it will display the ⬙service park assist system ⬙ message. Refer to “electronic vehicle information center (evic)” in section 4 of this ...

  • Page 146

    Warning! • drivers must be careful when backing up even when using the rear park assist system. Always check carefully behind your vehicle, look behind you, and be sure to check for pedestrians, animals, other vehicles, obstructions, and blind spots before back- ing up. You are responsible for safet...

  • Page 147

    Adjustable pedals — if equipped this feature allows both the brake and accelerator pedals to move toward the driver to provide improved position with the steering wheel. The adjustable pedal system is designed to allow a greater range of driver comfort for steering wheel tilt and seat position. The ...

  • Page 148

    • the pedals can be adjusted while driving. • the pedals cannot be adjusted when the vehicle is in r (reverse) or when the speed control is on. A message will be displayed in the electronic vehicle information center (evic) if the pedals are attempted to be ad- justed when the system is locked out (...

  • Page 149

    To activate press the on·off button to turn the system on. To turn the system off, press the on·off button again. The system should be turned off when not in use. The cruise indicator light in the instrument cluster will illuminate when the system is on. To set at a desired speed when the vehicle ha...

  • Page 150

    To vary the speed setting when the speed control is on, speed can be increased by pressing and holding the res·accel button. When the button is released, a new set speed will be estab- lished. Tapping the res·accel button once will result in a 2 mph (3 km/h) (3.7l/4.7l models) or a 1 mph (2 km/h) (5...

  • Page 151

    Warning! Leaving the speed control on when not in use is dangerous. You could accidentally set the system or cause it to go faster than you want. You could lose control and have an accident. Always leave the system off when you aren’t using it. Driving up or down hills when going up or down hills, i...

  • Page 152

    Overhead console — if equipped the overhead console contains an optional universal garage door opener (homelink 威), storage for sunglasses, and optional power sunroof switches. Garage door opener — if equipped the homelink 威 universal transceiver replaces up to three remote controls (hand held trans...

  • Page 153

    Warning! A moving garage door can cause injury to people and pets in the path of the door. People or pets could be seriously or fatally injured. Only use this transceiver with a garage door opener that has a “stop and reverse” feature as required by federal safety stan- dards. This includes most gar...

  • Page 154

    Programming homelink note: when programming a garage door opener, it is advised to park outside the garage. It is also recom- mended that a new battery be placed in the hand-held transmitter of the device being programmed to homelink for quicker training and accurate transmis- sion of the radio-freq...

  • Page 155

    2. Position the end of your hand-held transmitter 1-3 inches (3-8 cm) away from the homelink buttons. 3. Simultaneously press and hold both the homelink button that you want to train and the hand-held trans- mitter buttons. Do not release the buttons until step 4 has been completed. Note: some gate ...

  • Page 156

    Note: to program the remaining two homelink but- tons, begin with ⬙programming⬙ step two. Do not repeat step one. Note: if your hand-held transmitter appears to pro- gram the universal transceiver, but your garage door does not operate using the transmitter and your garage door opener was manufactur...

  • Page 157

    Canadian programming/gate programming canadian radio-frequency laws require transmitter sig- nals to ⬙time-out⬙ (or quit) after several seconds of transmission which may not be long enough for homelink to pick up the signal during programming. Similar to this canadian law, some u.S. Gate operators a...

  • Page 158

    • press and hold the two outer homelink buttons and release only when the evic display shows “chan- nels cleared” (after 20 seconds). Release both buttons. Do not hold for longer that 30 seconds. Homelink is now in the train (or learning) mode and can be programmed at any time beginning with ⬙pro- g...

  • Page 159

    Homelink 威 is a trademark owned by johnson controls, inc. Power sunroof — if equipped the power sunroof switch is located on the overhead console. Warning! • never leave children in a vehicle, with the keys in the ignition switch. Occupants, particularly unat- tended children, can become entrapped b...

  • Page 160

    Opening sunroof - express press the switch rearward and release, and the sunroof will open automatically from any position. The sunroof will open fully, then stop automatically. This is called express open. During express open operation, any movement of the sunroof switch will stop the sunroof. Clos...

  • Page 161

    Sunshade operation the sunshade can be opened manually. However, the sunshade will open automatically as the sunroof opens. Note: the sunshade cannot be closed if the sunroof is open. Wind buffeting wind buffeting can be described as the perception of pressure on the ears or a helicopter type sound ...

  • Page 162

    Note: hold onto shade handle until shade is com- pletely open or closed. Power outlet to the right of the convenience tray (lower center of instrument panel) is an outlet for electrically powered accessories. Pull lightly on the tab of the plastic cover to access the outlet. Roller shade front power...

  • Page 163

    The rear power outlet (if equipped) is located in the left rear cargo area. The power outlets are a direct feed from the battery so they receive power whether the ignition is in the on or off position. All accessories connected to this outlet should be re- moved or turned off when the vehicle is not...

  • Page 164

    Caution! Electrical outlet use with engine off • many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.E., cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or ...

  • Page 165

    Note: the cup holder insert is removable, from the console, for cleaning. It can be reinstalled with the larger cup depression towards the passenger seat, but the top surface will not be flush with the console surface. Cup holders (second row seat) the second row seat has two cup holders in the cent...

  • Page 166

    Cup holders (third row seat) the third row seat passengers have cup holders on the left and right rear trim panels. Cargo area features cargo load floor the panel in the load floor is reversible for added utility. One side is carpeted and the other side features a plastic lined tray which holds a va...

  • Page 167

    Note: the cargo load floor latches should not be used as cargo tie-downs. 1. Flip up pull loop(s) so they are perpendicular (straight up) to the top surface of the tray. 2. Pull up on loop(s) and twist 90 degrees, so they are parallel to the slotted hole in tray. 3. Lift tray over loop(s), and repos...

  • Page 168

    5. Push loop(s) back down, so they are parallel to the top of the tray. Rear window features rear window wiper/washer a switch on the right side of the steering column controls operation of the rear wiper/washer function. Rotating the center of the switch up to the del (delay) position or the on pos...

  • Page 169

    The rear wiper switch or the ignition switch needs to be turned off and on to restart the rear wiper. Adding washer fluid the fluid reservoir for the windshield washers and the rear window washer is shared. It is located in the front of the engine compartment on the passenger side and should be chec...

  • Page 170

    Note: if the rear cross rail (or any metallic object) is placed over the satellite radio antenna (if equipped), you may experience interruption of satellite radio reception. For improved satellite radio reception, place the rear cross rail in detent position #4 when not in use. Caution! • to prevent...

  • Page 171

    Warning! Cargo must be securely tied before driving your vehicle. Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in personal injury or property damage. Follow the roof rack “cautions” when carrying cargo on your roof rack. Understanding the features of your ...

  • Page 173: Contents

    Understanding your instrument panel contents 䡵 instrument panel and interior controls . . . . . . . 176 䡵 instrument cluster . . . . . . . . . . . . . . . . . . . . . . 177 䡵 instrument cluster description . . . . . . . . . . . . . 178 䡵 electronic vehicle information center — if equipped . . . . . ...

  • Page 174

    ▫ operation instructions - (cd mode for cd audio play) . . . . . . . . . . . 206 ▫ load/eject button (cd mode for cd audio play) . . . . . . . . . . . 208 ▫ notes on playing mp3 files . . . . . . . . . . . . . 210 ▫ operation instructions - (cd mode for mp3 audio play) . . . . . . . . . . 212 ▫ load...

  • Page 175

    ▫ selecting satellite mode in ref radios . . . . . . 227 ▫ selecting satellite mode in raq radios . . . . . 227 ▫ selecting a channel . . . . . . . . . . . . . . . . . . . . 228 ▫ storing and selecting pre-set channels . . . . . . 228 ▫ using the pty (program type) button — if equipped . . . . . . ....

  • Page 176

    Instrument panel and interior controls 176 understanding your instrument panel.

  • Page 177

    Instrument cluster understanding your instrument panel 177 4.

  • Page 178

    Instrument cluster description 1. Speedometer indicates vehicle speed. 2. Brake warning light the brake warning light will come on when the ignition is first turned on, and stay on briefly as a bulb check. If the bulb does not come on during starting, have the bulb re- paired promptly. If the light ...

  • Page 179

    Engine start. If the bulb does not come on when turning the key from off to on, have the condition checked promptly. Certain conditions such as a loose or missing gas cap, poor fuel quality, etc. May illuminate the light after engine start. The vehicle should be serviced if the light stays on throug...

  • Page 180

    If the abs light is on, the brake system should be serviced as soon as possible to restore the benefits of anti-lock brakes. If the abs light does not turn on when the ignition switch is turned to the on position, have the light inspected by an authorized dealer. 8. Tachometer the red segments indic...

  • Page 181

    Prevailing road conditions. The “esp/tcs indicator light” will flash any time the esp or tcs is active and helping to improve vehicle stability. If the “esp/tcs indicator light” is on solid, the esp system has been turned off by the driver or a temporary condition exists that will not allow full esp...

  • Page 182

    13. Temperature gauge the temperature gauge shows engine coolant tempera- ture. Any reading within the normal range indicates that the engine cooling system is operating satisfactorily. The gauge pointer will likely indicate a higher tempera- ture when driving in hot weather, up mountain grades, or ...

  • Page 183

    14. Electronic vehicle information center display when the appropriate conditions exist, this display shows the electronic vehicle information center (evic) messages. Refer to “electronic vehicle information cen- ter” later in this section. (see page 186 for more informa- tion.) 15. Tow/haul indicat...

  • Page 184

    Or remain on continuously. Refer to ⬙enhanced driver seat belt reminder system (beltalert) ⬙ in the occupant restraints section for more information. 19. Cruise indicator light this indicator lights when the speed control system is turned on. 20. Odometer the odometer shows the total distance the ve...

  • Page 185

    When the engine is running, immediate service is re- quired and you may experience reduced performance, an elevated/rough idle or engine stall and your vehicle may require towing. The light will come on when the ignition is first turned on and remain on briefly as a bulb check. If the light does not...

  • Page 186

    Electronic vehicle information center — if equipped the electronic vehicle information center (evic) located in the instrument cluster, when the appropriate condi- tions exist, will display the following messages and symbols. Some of the messages are accompanied by a chime. • turn signal on • perfor...

  • Page 187

    • liftgate/door open (with graphic) • liftgate/doors open (with graphic) • liftglass open (with graphic) • hood open (with graphic) • hood/door open (with graphic) • hood/doors open (with graphic) • liftgate/hood open (with graphic) • hood/glass/door open (with graphic) • hood/glass/doors open (with...

  • Page 188

    • check gas cap • esp off • memory #1 positions set • memory #2 positions set • memory system disabled — seatbelt fas- tened (with graphic) • memory system disabled — vehicle not in park • driver 1 memory • driver 2 memory • pedal adjust disabled — cruise control set • pedal adjust disabled — shifte...

  • Page 189

    Customer programmable features press the menu button until one of the display choices following appears: language? When in this display you may select one of three lan- guages for all display nomenclature, including the trip computer functions. Press the step button while in this display selects eng...

  • Page 190

    Display u.S. Or metric? Pressing the step button when in this display selects us or metric. The overhead console and instrument panel displays will be in the selected units. Auto door locks? When this feature is selected, all doors and the liftgate lock automatically when the speed of the vehicle re...

  • Page 191

    Memory set position using the door mounted switch. Pressing the step button when in this display will select “yes” or “no.” sound horn with lock? When this feature is selected a short horn sound will occur when the remote keyless entry “lock” button is pressed. This feature may be selected with or w...

  • Page 192

    This display will select “low beam” or “low/high beam.” refer to “lights — smartbeams” in section 3 of this manual. Note: system will activate at or above 20 mph (32 km/h). Headlamps on with wipers? (available with auto headlights only) when this feature is selected and the headlight switch has at l...

  • Page 193

    Easy entry/exit seat? (available with memory seat only) this feature provides automatic driver’s seat positioning which will enhance driver mobility out of and into the vehicle. The easy entry/ easy exit feature is not enabled when the vehicle is delivered from the factory. The easy entry/ easy exit...

  • Page 194

    Warning! Even if the display still reads a few degrees above 32°f ( 0°c), the road surface may be icy, particularly in woods or on bridges. Drive carefully under such conditions to prevent an accident and possible per- sonal injury or property damage. Compass/temperature display 194 understanding yo...

  • Page 195

    Trip computer this feature, located in the instrument cluster, displays the following information when the display is in the “compass/temperature” mode and the step button is pressed: step button press the step button to cycle through all of the compass/mini-trip computer displays. Step button under...

  • Page 196

    Reset button press the reset button to reset the display you are in. Press and hold the reset button (for 2 seconds) to reset all of the displays. Average fuel economy shows the average fuel economy since the last reset. When the fuel economy is reset, the display will read “reset” or show dashes fo...

  • Page 197

    Elapsed time shows the accumulated ignition on time since the last reset. Tire pressure display — if equipped shows the current pressure of all 4 road tires. Note: tires heat up during normal driving conditions. Heat will cause the tire pressure to increase from 2 to 6 psi (14 to 41 kpa) during norm...

  • Page 198

    Note: to ensure proper compass calibration, make sure the compass variance is properly set before manu- ally calibrating the compass. Refer to variance map. To put into a calibration mode start the engine and leave the transmission in the p (park) position. Set the display to “compass/temperature.” ...

  • Page 199

    To set the variance: turn the ignition on and set the display to “compass/temperature.” press the c/t but- ton for approximately 5 seconds. The last variance zone number will be displayed. Press and hold the step button for 1 second to select the new variance zone and press the reset button to resum...

  • Page 200

    Two types of signals there are two basic types of radio signals... Am or amplitude modulation, in which the transmitted sound causes the amplitude, or height, of the radio waves to vary... And fm or frequency modulation, in which the frequency of the wave is varied to carry the sound. Electrical dis...

  • Page 201

    Operating instructions - radio mode note: the ignition switch must be in the on or acc position to operate the radio. Power switch/volume control (rotary) press the on/vol control to turn the radio on. Press the on/vol a second time to turn off the radio. Electronic volume control the electronic vol...

  • Page 202

    Seek button (radio mode) press and release the seek button to search for the next listenable station in either am/fm or satellite (if equipped) mode. Press the right side of the button to seek up and the left side to seek down. The radio will remain tuned to the new station until you make another se...

  • Page 203

    2. Adjust the hours by turning the right side tune / audio control. 3. After the hours are adjusted, press the right side tune / audio control to set the minutes. The minutes will begin to blink. 4. Adjust the minutes using the right side tune / audio control. 5. To exit, press any button/knob or wa...

  • Page 204

    Press the rotary tune control a fifth time and fade will display. Turn the tune control to the left or right to adjust the sound level between the front and rear speak- ers. Press the rotary tune control again to exit setting tone, balance and fade. Rnd/pty button (radio mode) pressing this button o...

  • Page 205

    Nostalgia nostalgia oldies oldies personality personality public public rhythm and blues rhythm_and_blues religious music religious_music religious talk religious_talk rock rock soft soft soft rock soft_rock soft rhythm and blues soft_r_&_b sports sports talk talk top 40 top_40 weather weather by pr...

  • Page 206

    You may add a second station to each push-button by repeating the above procedure with this exception: press the set/dir button twice and set 2 will show in the display window. Each button can be set for set 1 and set 2 in both am and fm. This allows a total of 12 am,12 fm and 12 satellite (if equip...

  • Page 207

    Caution! This cd player will accept 4 3/4 inch (12 cm) discs only. The use of other sized discs may damage the cd player mechanism. You may eject a disc with the radio off. If you insert a disc with the ignition on and the radio on, the unit will switch from radio to cd mode and begin to play when y...

  • Page 208

    Load/eject button (cd mode for cd audio play) load/ eject - load press the load/ eject button and the push- button with the corresponding number where the cd is being loaded. The radio will display please wait and prompt when to insert disc. After the radio displays ⬙load disc⬙ insert the cd into th...

  • Page 209

    Time button (cd mode for cd audio play) press this button to change the display from a large cd playing time display to a small cd playing time display. Rw/ff (cd mode for cd audio play) press and hold ff (fast forward) and the cd player will begin to fast forward until ff is released or rw or anoth...

  • Page 210

    Notes on playing mp3 files the radio can play mp3 files, however, acceptable mp3 file recording media and formats are limited. When writing mp3 files, pay attention to the following restric- tions. Supported media (disc types) the mp3 file recording media supported by the radio are cd-rom, cd-r and ...

  • Page 211

    Supported mp3 file formats the radio will recognize only files with the *.Mp3 exten- sion as mp3 files. Non-mp3 files named with the *.Mp3 extension may cause playback problems. The radio is designed to recognize the file as an invalid mp3 and will not play the file. When using the mp3 encoder to co...

  • Page 212

    Playback of mp3 files when a medium containing mp3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the mp3 files. Loading times for playback of mp3 files may be affected by the following: • med...

  • Page 213

    Load / eject - eject press the load/ eject button and the push- button with the corresponding number where the cd was loaded and the disc will unload and move to the entrance for easy removal. Radio display will show ⬙ejecting disc⬙ when the disc is being ejected and prompt the user to remove the di...

  • Page 214

    Am/fm button (cd mode for mp3 play) switches back to radio mode. Rnd/ pty button (cd mode for mp3 play) pressing this button plays files randomly. Set/dir button (cd mode for mp3 play) press the set/dir button to display folders, when playing an mp3 discs that have a file/folder structure. Turn the ...

  • Page 215

    Operating instructions - radio mode note: the ignition switch must be in the on or acc position to operate the radio. Power switch/volume control (rotary) press the on/vol control to turn the radio on. Press the on/vol a second time to turn off the radio. Electronic volume control the electronic vol...

  • Page 216

    Seek button (radio mode) press and release the seek button to search for the next listenable station in either am/fm or satellite (if equipped) mode. Press the right side of the button to seek up and the left side to seek down. The radio will remain tuned to the new station until you make another se...

  • Page 217

    2. Adjust the hours by turning the right side tune/ audio control. 3. After the hours are adjusted, press the right side tune/audio control to set the minutes. The minutes will begin to blink. 4. Adjust the minutes using the right side tune/audio control. 5. To exit, press any button/knob or wait 5 ...

  • Page 218

    Press the rotary tune control a fifth time and fade will be displayed. Turn the tune control to the left or right to adjust the sound level between the front and rear speak- ers. Press the tune control again or wait 5 seconds to exit setting tone, balance, and fade. Rnd/set button (radio mode) to se...

  • Page 219

    Inserting the compact disc (single cd player) gently insert one cd into the cd player with the cd label facing up. The cd will automatically be pulled into the cd player and the cd icon will illuminate on the radio display. If the volume control is on, the unit will switch to cd mode and begin to pl...

  • Page 220

    Eject button (cd mode) press this button and the disc will unload and move to the entrance for easy removal. The unit will switch to the last selected mode. If you do not remove the disc within 15 seconds, it will be reloaded. The radio mode will continue to appear. Time button (cd mode) press this ...

  • Page 221

    Operation instructions - auxiliary mode the auxiliary (aux) jack is an audio input jack, which allows the user to plug in a portable device such as an mp3 player, cassette player or microphone and utilize the vehicle’s audio system to amplify the source and play through the vehicle speakers. The aux...

  • Page 222

    Time button (auxiliary mode) press this button to change the display from elapsed playing time to time of day. The time of day will be displayed for 5 seconds. Rw/ff (auxiliary mode) no function. Rnd/set button (auxiliary mode) no function. Mode button (auxiliary mode) press the mode button repeated...

  • Page 223

    Satellite navigation radio with cd player with mp3 capability (rec) - combines a global-positioning system-based navigation system with an integrated color screen to provide maps, turn identification, selection menus and instructions for selecting a variety of destina- tions and routes, am/fm stereo...

  • Page 224

    Video entertainment system (sales code xrv) — if equipped the optional ves™ (video entertainment system) con- sists of a dvd player and lcd (liquid crystal display) screen, a battery-powered remote control, and two head- sets. The dvd player is mounted in the rear of the center console storage bin, ...

  • Page 225

    The lcd screen is located on the headliner behind the front seats. Lowering the display screen remote control location understanding your instrument panel 225 4.

  • Page 226

    Satellite radio — if equipped satellite radio uses direct satellite to receiver broadcast- ing technology to provide clear digital sound, coast to coast. The subscription service provider is sirius™ satel- lite radio. This service offers over 100 channels of music, sports, news, entertainment, and p...

  • Page 227

    First four digits are displayed. The radio will exit the esn/sid mode when any other button is pushed, the ignition is turned off, or 5 minutes has passed since any button was pushed. Esn/sid access with raq radios with the ignition switch in the accessory position and the radio off, press the cd ej...

  • Page 228

    Selecting a channel press and release the seek or tune buttons to search for the next channel. Press the top of the button to search up and the bottom of the button to search down. Holding the tune button causes the radio to bypass channels until the button is released. Press and release the scan bu...

  • Page 229

    Note: pressing the ⬙seek⬙ or ⬙scan⬙ button while performing a music type scan will change the channel by one and stop the search. Pressing a pre-set memory button during a music type scan, will call up the memory channel and stop the search. Pty button ⴖseekⴖ when the desired program is obtained, pr...

  • Page 230

    Remote sound system controls — if equipped the remote sound system controls are located on the rear surface of the steering wheel. Reach behind the wheel to access the switches. The right hand control is a rocker type switch with a push-button in the center and controls the volume and mode of the so...

  • Page 231

    The button located in the center of the left hand control will tune to the next preset station that you have pro- grammed in the radio preset push-button. Cd player pressing the top of the switch once will go to the next track on the cd. Pressing the bottom of the switch once will go to the beginnin...

  • Page 232

    Radio operation and cellular phones under certain conditions, the cellular phone being on in your vehicle can cause erratic or noisy performance from your radio. This condition may be lessened or eliminated by relocating the cellular phone antenna. This condition is not harmful to the radio. If your...

  • Page 233

    Press this button to turn on and off the air condi- tioning. Cool dehumidified air comes through the outlets selected by the mode selector. Press the button a second time to turn off the air conditioning. The button includes an led that illuminates when compres- sor operation is selected. Electric r...

  • Page 234

    Temperature control the temperature of air can be selected by rotating the center temperature control knob. The coldest temperature setting is on the extreme left and the warmest setting on the extreme right of the rotation. The knob can be posi- tioned at any point on the dial. Mode selection the m...

  • Page 235

    Bi-level air flows both through the outlets located in the instrument panel and those located on the floor. Air flows through the registers in the back of the center console, and under the front seats to the rear seat passengers. These registers can be closed to partially block airflow. The center c...

  • Page 236

    Operating tips 236 understanding your instrument panel.

  • Page 237

    Automatic temperature control — if equipped the infrared dual-zone climate control system auto- matically maintains the interior comfort level desired by the driver and passenger. This is accomplished by a dual sun-sensor in the top of the instrument panel, and an infrared sensor located in the face...

  • Page 238

    Lo auto position should be used for front seat occu- pants only. The hi auto position should be used when more air flow is desired, or when rear seat occupants are present. Dial in the comfort setting you would like the system to maintain by rotating the driver’s or passenger’s control knob. Once th...

  • Page 239

    Note: • the surface of the climate control panel, and the top center of the instrument panel should be kept free of debris due to the climate control sensor’s location. Mud on the windshield may also cause poor operation of this system. • to provide you with maximum comfort in the auto- matic mode, ...

  • Page 240

    240 understanding your instrument panel.

  • Page 241

    Note: regardless of the type of operation, when a temperature knob is set to the full clockwise or full counterclockwise position, the system will deliver full hot or full cold air out of the ducts, respectively. The operator can override the auto mode setting and select the direction of the air by ...

  • Page 242

    Air flows through the registers in the back of the center console, and under the front seats to the rear seat passengers. These registers can be closed to block airflow. The center console outlets deliver conditioned air while the floor outlets deliver heated air. • panel air flows through the outle...

  • Page 243

    This button can be used to block out smoke, odors, dust, high humidity, or if rapid cooling is desired. The recirculation mode should only be used temporarily. The button includes an led that illuminates, which indicates that the recircula- tion mode is active. You may use this feature separately. N...

  • Page 244

    Rear mode control if rear heating/cooling is desired, press the “rear on/off switch” (located in the upper switch bank above the controls) and select “floor” “bi-level” or “panel” from the rear control panel (right knob located on the right rear quarter trim panel). • floor air flows through the flo...

  • Page 245

    • bi-level air flows through both the outlets located in the rear quarter trim panels, and the one located on the floor. The rear quarter trim panel outlets can be closed to block airflow. • panel air flows through the outlets located in the rear quarter trim panels. These registers can be closed to...

  • Page 246

    • when the temperature knob is in the cold (blue) position, cold air will be delivered from the outlets. As the temperature knob is turned towards the hot (red) position, the air will get warmer. Summer operation the engine cooling system in air conditioned vehicles must be protected with a high-qua...

  • Page 247

    Window fogging interior fogging on the windshield can be quickly re- moved by turning the mode selector to defrost, and turning on the high blower. The defrost/floor mode can be used to maintain a clear windshield and provide sufficient heating. If side window fogging becomes a problem increase blow...

  • Page 249: Starting And Operating

    Starting and operating contents 䡵 starting procedures . . . . . . . . . . . . . . . . . . . . . 253 ▫ normal starting . . . . . . . . . . . . . . . . . . . . . . 253 ▫ extreme cold weather (below –20°f (–29°c) . . 254 ▫ if engine fails to start . . . . . . . . . . . . . . . . . 254 ▫ after starting ...

  • Page 250

    䡵 anti-lock brake system . . . . . . . . . . . . . . . . . . 271 䡵 power steering . . . . . . . . . . . . . . . . . . . . . . . . 274 䡵 on-road driving tips . . . . . . . . . . . . . . . . . . . 275 䡵 off-road driving tips . . . . . . . . . . . . . . . . . . . 276 ▫ when to use 4wd low range — if eq...

  • Page 251

    䡵 tire pressure monitor system (tpms) . . . . . . . . 297 ▫ base system . . . . . . . . . . . . . . . . . . . . . . . . . 297 ▫ premium system . . . . . . . . . . . . . . . . . . . . . . 299 ▫ general information . . . . . . . . . . . . . . . . . . . 303 䡵 tire chains . . . . . . . . . . . . . . . ....

  • Page 252

    ▫ towing – 2wd models . . . . . . . . . . . . . . . . . 323 ▫ towing — quadra-trac i (single-speed transfer case) 4wd models . . . . 323 ▫ towing — quadra–trac ii /quadra–drive ii 4wd models . . . . . . . . . . . . . . . . . . . . . . . . 324 䡵 snow plow . . . . . . . . . . . . . . . . . . . . . . ....

  • Page 253

    Starting procedures before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. Warning! Do not leave children or animals inside parked vehicles in hot weather. Interior heat build up may cause serious injury or death. The gear selector must be...

  • Page 254

    Warning! Never pour fuel or other flammable liquids into the throttle body air inlet opening in an attempt to start the vehicle. This could result in a flash fire causing serious personal injury. Extreme cold weather (below –20°f (–29°c) to insure reliable starting at these temperatures, use of an e...

  • Page 255

    After starting the idle speed will automatically decrease as the engine warms up. Caution! Long periods of engine idling, especially at high engine speeds can cause excessive exhaust tempera- tures which can damage your vehicle. Do not leave your vehicle unattended with the engine running. Engine bl...

  • Page 256

    Transmission shifting 5–speed automatic transmission the electronically controlled transmission provides a precise shift schedule. The transmission electronics are self-calibrating; therefore, the first few shifts on a new vehicle, may be somewhat abrupt. This is a normal condition, and precision sh...

  • Page 257

    Warning! It is dangerous to shift the selector lever out of p (park) or n (neutral) if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in reverse. You could lose control of the vehicle and hit someone or somet...

  • Page 258

    Warning! Unintended movement of a vehicle could injure those in and near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, you should apply the park brake, shift the transmission into p (park), and remove the key from the igniti...

  • Page 259

    Shifter is in the d (drive) position, allowing the selection of the desired top gear. For example, if the driver shifts the transmission into 3 (third gear), the transmission will never shift above third gear, but can shift down to 2 (second) or 1 (first), when needed. Warning! Do not downshift for ...

  • Page 260

    Note: if the vehicle is started in extremely cold tem- peratures, the transmission may not shift into overdrive and will automatically select the most desirable gear for operation at this temperature. Normal operation will resume when the transmission fluid temperature has risen to a suitable level....

  • Page 261

    Overheating or failure due to excessive shifting. When operating in “tow/haul” mode, the transmission will shift to 3rd gear and 4th will be enabled under steady cruise conditions. The “tow/haul” light will illuminate in the instru- ment cluster to indicate when the switch has been activated. Pressi...

  • Page 262

    4. Wait approximately 10 seconds, then restart the en- gine. 5. Move the shift lever to the desired gear range. If the problem is no longer detected, the transmission will return to normal operation. If the problem persists, p (park), r (reverse), and n (neutral) will continue to operate. Only secon...

  • Page 263

    Cause damage to the transmission. The torque converter will refill within five seconds of shifting from park into any other gear position. Rocking the vehicle if the vehicle becomes stuck in snow, sand, or mud, it can often be moved by a rocking motion. Move the gear selector rhythmically between d ...

  • Page 264

    Four-wheel drive operation quadra-trac i 姞 operating instructions/precautions — if equipped the quadra-trac i 威 is a single speed (hi range only) transfer case which provides convenient full-time 4–wheel drive. No driver interaction is required. This transfer case divides engine torque almost evenly...

  • Page 265

    Road surfaces only. Driving in the 4 low position on dry hard surfaced roads may cause increased tire wear and damage to driveline components. When operating your vehicle in 4 low, the engine speed is approximately three times that of the 4 hi position at a given road speed. Take care not to overspe...

  • Page 266

    N (neutral) neutral — disengages both the front and rear driveshafts from the powertrain. To be used for flat towing behind another vehicle. Refer to “recreational towing” in sec- tion 5 of this manual. 4 low four wheel drive low range — low speed 4 wheel drive. Locks the front and rear driveshafts ...

  • Page 267

    4 low to 4 hi with the vehicle at speeds of 0 to 3 mph (0 to 5 km/h), key on or engine running, shift the transmission into n (neutral), and raise the transfer case t-handle. The “4wd low indicator lamp” in the instrument cluster will flash and go out when the shift is complete. Release the t-handle...

  • Page 268

    Neutral (n) shift procedure 1. Key on, engine off. 2. Vehicle stopped, with foot on brake. 3. Place transmission in n (neutral). 4. Hold down n (neutral) “pin” switch (with a pen, etc.) for 4 seconds until the led lamp by the switch starts to blink indicating shift in progress. Lamp will stop blinki...

  • Page 269

    Note: if shift conditions/interlocks are not met, a “check shift procedures” message will flash from the evic (electronic vehicle information center). Refer to “electronic vehicle information center (evic)” in section 4 of this manual. (see page 186 for more information.) quadra-drive ii 姞 system — ...

  • Page 270

    Note: the instrument cluster “brake warning light” indicates only that the parking brake is applied. It does not indicate the degree of brake application. Before leaving the vehicle parked on a hill, you must make sure the parking brake is fully applied and place the gear selector in the p (park) po...

  • Page 271

    Warning! • leaving children unattended in a vehicle is dan- gerous for a number of reasons. A child or others could be injured. Children should be warned not to touch the parking brake or the gear selector lever. Don’t leave the keys in the ignition. A child could operate power windows, other contro...

  • Page 272

    Warning! Significant over or under inflation of tires, or mixing sizes of tires or wheels on the vehicle can lead to loss of braking effectiveness. The anti-lock brake system conducts a low-speed self- test at about 12 mph (20 km/h). If you have your foot lightly on the brake while this test is occu...

  • Page 273

    Warning! • the anti-lock brake system (abs) cannot pre- vent the natural laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency beyond that afforded by the condition of the vehicle brakes and tires or the traction afforded. • the abs cannot prevent accidents, ...

  • Page 274

    • do not “ride” the brakes by resting your foot on the pedal. This could overheat the brakes and result in unpredictable braking action, longer stopping dis- tances, or brake damage. • when descending mountains or hills, repeated brak- ing can cause brake fade with loss of braking control. Avoid rep...

  • Page 275

    Note: increased noise levels at the end of the steering wheel travel are considered normal and does not indicate that there is a problem with the power steering system. Upon initial start-up in cold weather, the power steering pump may make noise for a short period of time. This is due to the cold, ...

  • Page 276

    Conventional 2-wheel drive vehicles any more than low- slung sports cars are designed to perform satisfactorily in off-road conditions. If at all possible, avoid sharp turns or abrupt maneuvers. As with other vehicles of this type, failure to operate this vehicle correctly may result in loss of cont...

  • Page 277

    Caution and maintain a steady controlled speed less than 5 mph (8 km/h) in deep water to minimize wave effects. Flowing water if the water is swift flowing and rising (as in storm run-off) avoid crossing until the water level recedes and/or the flow rate is reduced. If you must cross flowing water a...

  • Page 278

    Hill climbing note: before attempting to climb a hill, determine the conditions at the crest and/or on the other side. Before climbing a steep hill, shift the transmission to a lower gear and shift the transfer case to 4wd low. Use first gear and 4wd low for very steep hills. If you stall or begin t...

  • Page 279

    Traction downhill shift the transmission into a low gear and the transfer case to 4wd low range. Let the vehicle go slowly down the hill with all four wheels turning against engine compression drag. This will permit you to control the vehicle speed and direction. When descending mountains or hills, ...

  • Page 280

    Warning! Abrasive material in any part of the brakes may cause excessive wear or unpredictable braking. You might not have full braking power when you need it to prevent an accident. If you have been operating your vehicle in dirty conditions, get your brakes checked and cleaned as necessary. • if y...

  • Page 281

    Tire safety information tire markings note: • p (passenger)-metric tire sizing is based on u.S. Design standards. P-metric tires have the letter “p” molded into the sidewall preceding the size designation. Ex- ample: p215/65r15 95h. • european metric tire sizing is based on european design standards...

  • Page 282

    Tire sizing chart example: size designation: p = passenger car tire size based on u.S. Design standards ⴖ....Blank....ⴖ = passenger car tire based on european design standards lt = light truck tire based on u.S. Design standards t = temporary spare tire 31 = overall diameter in inches (in) 215 = sec...

  • Page 283

    Example: service description: 95 = load index —a numerical code associated with the maximum load a tire can carry. H = speed symbol —a symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions. —the maximum speed corresp...

  • Page 284

    Tire identification number (tin) the tin may be found on one or both sides of the tire however the date code may only be on one side. Tires with white sidewalls will have the full tin including date code located on the white sidewall side of the tire. Look for the tin on the outboard side of black s...

  • Page 285

    Tire loading and tire pressure tire placard location note: the proper cold tire inflation pressure is listed on either the face of the driver’s door or the driver’s side “b” pillar. Tire and loading information placard this placard tells you important information about the: 1) number of people that ...

  • Page 286

    3) the tire size designed for your vehicle 4) the cold tire inflation pressures for the front, rear and spare tires. Loading the vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adher...

  • Page 287

    4. The resulting figure equals the available amount of cargo and luggage load capacity. For example, if “xxx” amount equals 1400 lbs. And there will be five 150 lb. Passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lb. (since 5 x 150 = 750, and 1400 – 750 = 6...

  • Page 288

    288 starting and operating.

  • Page 289

    Warning! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. Tires — general information tire pressure proper tire inflation pressur...

  • Page 290

    2. Economy— improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Under inflation also increases tire rolling resistance and results in higher fuel consump- t...

  • Page 291

    Check tire pressure. Do not make a visual judgement when determining proper inflation. Radial tires may look properly inflated even when they are under inflated. Caution! After inspecting or adjusting the tire pressure al- ways reinstall the valve stem cap–if equipped. This will prevent moisture and...

  • Page 292

    Tire pressures for high speed operation the manufacturer advocates driving at safe speeds within posted speed limits. Where speed limits or condi- tions are such that the vehicle can be driven at high speeds, maintaining correct tire inflation pressure is very important. Increased tire pressure and ...

  • Page 293

    Radial-ply tires warning! Combining radial ply tires with other types of tires on your vehicle will cause your vehicle to handle poorly. The instability could cause an accident. Al- ways use radial tires in sets of four. Never combine them with other types of tires. Cuts and punctures in radial tire...

  • Page 294

    Tread wear indicators tread wear indicators are in the original equipment tires to help you in determining when your tires should be replaced. These indicators are molded into the bottom of the tread grooves and will appear as bands when the tread depth becomes 1/16 inch (2 mm). When the indicators ...

  • Page 295

    Warning! Tires and spare tire should be replaced after six years, regardless of the remaining tread. Failure to follow this warning can result in sudden tire failure. You could lose control and have an accident result- ing in serious injury or death. Keep unmounted tires in a cool, dry place with as...

  • Page 296

    Warning! • do not use a tire, wheel size or rating other than that specified for your vehicle. Some combina- tions of unapproved tires and wheels may change suspension dimensions and performance charac- teristics, resulting in changes to steering, han- dling, and braking of your vehicle. This can ca...

  • Page 297

    Improper alignment will not cause vehicle vibration. Vibration may be a result of tire and wheel out-of- balance. Proper balancing will reduce vibration and avoid tire cupping and spotty wear. Tire pressure monitor system (tpms) base system the tire pressure monitor system (tpms) uses wireless techn...

  • Page 298

    Note: for vehicles with optional wheel/tire sizes and significantly different tire placard pressures, the placard pressure value and the low-pressure threshold value is re-programmable at your authorized dealer to accommo- date the customer selected wheel/tire combinations rec- ommended by daimlerch...

  • Page 299

    Caution! After inspecting or adjusting the tire pressure al- ways reinstall the valve stem cap. This will prevent moisture and dirt from entering the valve stem, which could damage the wheel rim sensor. Note: • the tpms can inform the driver of a low tire pressure condition. • the tpms is not intend...

  • Page 300

    When a system fault is detected. The flash cycle will repeat every ten minutes or until the fault condition is removed and reset. The tire pressure monitor system (tpms) consists of the following components: • receiver module • 5 wheel sensors (including full size spare tire) • 4 wheel sensor trigge...

  • Page 301

    Telltale light” will illuminate continuously (solid) and shall remain illuminated until the warning condition is removed/reset. Note: the “tire pressure monitoring telltale light” will only illuminate for the four active road tires. A low spare tire pressure will not cause the “tire pressure monitor...

  • Page 302

    Caution! The tpms has been optimized for the original equipment tires and wheels. Tpms pressures have been established for the tire size equipped on your vehicle. Undesirable system operation or sensor damage may result when using replacement equip- ment that is not of the same size, type, and/or st...

  • Page 303

    General information this device complies with part 15 of the fcc rules and rss 210 of industry canada. Operation is subject to the following conditions: • this device may not cause harmful interference. • this device must accept any interference received, including interference that may cause undesi...

  • Page 304

    Tire rotation recommendations tires on the front and rear axles of vehicles operate at different loads and perform different steering, handling, and braking functions. For these reasons, they wear at unequal rates, and develop irregular wear patterns. These effects can be reduced by timely rotation ...

  • Page 305

    Fuel requirements 3.7/4.7l engines (if equipped) all engines (except 5.7l engines) are de- signed to meet all emissions regulations and provide excellent fuel economy and performance when using high quality un- leaded “regular” gasoline having an oc- tane rating of 87. The use of premium gasoline is...

  • Page 306

    Over 40 auto manufacturer’s world wide have issued and endorsed consistent gasoline specifications (the world- wide fuel charter, wwfc) to define fuel properties necessary to deliver enhanced emissions, performance, and durability for your vehicle. The manufacturer recom- mends the use of gasoline t...

  • Page 307

    Mmt in gasoline mmt is a manganese containing metallic additive that is blended into some gasoline to increase octane. Gasoline blended with mmt provides no performance advantage beyond gasoline of the same octane number without mmt. Gasoline blended with mmt reduces spark plug life and reduces emis...

  • Page 308

    • an out-of-tune engine, or certain fuel or ignition malfunctions, can cause the catalytic converter to overheat. If you notice a pungent burning odor or some light smoke, your engine may be out of tune or malfunctioning and may require immediate service. Contact your dealer for service assistance. ...

  • Page 309

    • guard against carbon monoxide with proper mainte- nance. Have the exhaust system inspected every time the vehicle is raised. Have any abnormal conditions repaired promptly. Until repaired, drive with all side windows fully open. • keep the liftgate closed when driving your vehicle to prevent carbo...

  • Page 310

    Caution! Damage to the fuel system or emission control system could result from using an improper fuel cap (gas cap). A poorly fitting cap could let impurities into the fuel system. Also, a poorly fitting after- market cap can cause the mil (malfunction indica- tor light) to illuminate, due to fuel ...

  • Page 311

    Loose fuel filler cap message if the vehicle diagnostic system determines that the fuel filler cap is loose, improperly installed, or damaged, a “check gas cap” message will be displayed in the evic (electronic vehicle information center). Refer to “electronic vehicle information center” in section ...

  • Page 312

    Warning! A fire may result if gasoline is pumped into a portable container that is inside of a vehicle. You could be burned. Always place gas containers on the ground while filling. Trailer towing in this section you will find safety tips and information on limits to the type of towing you can reaso...

  • Page 313

    Gross combination weight rating (gcwr) the gross combination weight rating (gcwr) is the total permissible weight of your vehicle and trailer when weighed in combination. (note that gcwr ratings in- clude a 150 lbs (68 kg) allowance for the presence of a driver). Gross axle weight rating (gawr) the ...

  • Page 314

    Hitches are the most popular on the market today and they’re commonly used to tow small- and medium-sized trailers. Weight-distributing hitch a weight-distributing hitch includes a receiver attached to the tow vehicle, plus a removable hitch head and spring bar assembly that fits into the receiver o...

  • Page 315

    Trailer towing weights (maximum trailer weight ratings) the following chart provides the maximum trailer weight ratings towable for your given drivetrain. Engine/ transmission model gvwr (gross ve- hicle wt. Rating) gcwr (gross com- bined wt. Rating) frontal area max. Gtw (gross trailer wt.) max. To...

  • Page 316

    Note 1 – the trailer tongue weight must be considered as part of the combined weight of occupants and cargo, and should never exceed the weight referenced on the tire and loading information placard. Refer to the tire– safety information section in this manual. Trailer and tongue weight always load ...

  • Page 317

    Note: remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options, or dealer-installed options, must be considered as part of the total load on your vehicle. Refer to the tire and loading information plac- ard in the tire safety in...

  • Page 318

    Warning! Improper towing can lead to an injury accident. Follow these guidelines to make your trailer towing as safe as possible: make certain that the load is secured in the trailer and will not shift during travel. When trailering cargo that is not fully secured, dynamic load shifts can occur that...

  • Page 319

    2. Gtw 3. Gawr 4. Tongue weight rating for the trailer hitch utilized (this requirement may limit the ability to always achieve the 10% to 15% range of tongue weight as a percentage of total trailer weight). Towing requirements — tires − do not attempt to tow a trailer while using a compact spare ti...

  • Page 320

    − an electronically actuated trailer brake controller is required when towing a trailer with electronically actuated brakes. When towing a trailer equipped with a hydraulic surge actuated brake system, an electronic brake controller is not required. − trailer brakes are recommended for trailers over...

  • Page 321

    Note: do not cut or splice wiring into the vehicles wiring harness. The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector. Refer to the following illustrations. Towing tips before setting out on a trip, practice turning, stopping and backing ...

  • Page 322

    If using a manual transmission vehicle for trailer towing, all starts must be in first gear to avoid excessive clutch slippage. Towing tips — automatic transmission the “d” range can be selected when towing. However, if frequent shifting occurs while in this range, the ”tow/ haul” mode (if equipped)...

  • Page 323

    − city driving when stopped for short periods of time, put transmission in neutral and increase engine idle speed. − highway driving reduce speed. − air conditioning turn off temporarily. − refer to cooling system operating information in the maintenance section of this manual for more informa- tion...

  • Page 324

    Towing — quadra–trac ii /quadra–drive ii 4wd models caution! Front or rear wheel lifts should not be used. Internal damage to the transmission or transfer case will occur if a front or rear wheel lift is used when recreational towing. Note: the transfer case must be in the n (neutral) position, and ...

  • Page 325

    “electronic vehicle information center (evic)” in sec- tion 4 of this manual. (see page 186 for more informa- tion.) 5. Start engine. 6. Shift transmission into d (drive). 7. Release brake pedal and ensure that there is no vehicle movement. 8. Shut the engine off. 9. Shift transmission into p (park)...

  • Page 326

    Caution! Transmission damage may occur if the transmission is shifted into p (park) with the transfer case in n (neutral) and the engine running. With the transfer case in n (neutral) ensure that the engine is off prior to shifting the transmission into p (park) (refer to steps 7 – 8 above). Shiftin...

  • Page 327

    5. Shift transmission into p (park). 6. Start the engine. 7. Shift transmission into d (drive). Note: when shifting out of transfer case n (neutral), turning the engine off may be required to avoid gear clash. Warning! You or others could be injured if you leave the vehicle unattended with the trans...

  • Page 328

    Caution! Do not use a bumper mounted clamp-on tow bar on your vehicle. The bumper face bar will be damaged. Snow plow snow plows, winches, and other aftermarket equipment should not be added to the front end of your vehicle. The airbag crash sensors may be affected by the change in the front end str...

  • Page 329: Contents

    What to do in emergencies contents 䡵 hazard warning flashers . . . . . . . . . . . . . . . . . 330 䡵 if your engine overheats . . . . . . . . . . . . . . . . . 331 䡵 jacking and tire changing . . . . . . . . . . . . . . . . 332 ▫ jack location . . . . . . . . . . . . . . . . . . . . . . . . 332 ▫ sp...

  • Page 330

    Hazard warning flashers your vehicle’s hazard warning flasher is an emergency warning system. When you activate it, all front and rear directional signals will flash intermittently. Use it when your vehicle is disabled on or near the road. It warns other drivers to steer clear of you and your vehicl...

  • Page 331

    If your engine overheats in any of the following situations, you can reduce the potential for overheating by taking the appropriate ac- tion. • on the highways — slow down. • in city traffic — while stopped, put transmission in n (neutral), but do not increase engine idle speed. Note: there are step...

  • Page 332

    Jacking and tire changing warning! • getting under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never get any part of your body under a vehicle that is on a jack. If you need to get under a raised vehicle, take it to a service center wh...

  • Page 333

    Spare tire stowage the spare tire is stowed under the rear of the vehicle by means of a cable winch mechanism. To remove or stow the spare, use the jack handle to rotate the “spare tire drive” nut. The nut is located under a plastic cover at the center-rear of the cargo floor area, just inside the l...

  • Page 334

    Spare tire removal fit the jack handle extension over the drive nut. Use the lug wrench to rotate the nut counter clockwise until the spare is on the ground with enough slack in the cable to allow to pull the tire out from under the vehicle. Caution! The winch mechanism is designed for use with the ...

  • Page 335

    For example, if changing the right front tire, block the left rear wheel. • passengers should not remain in the vehicle when the vehicle is being jacked. Jacking instructions 1. Remove the spare tire, jack, and tools from storage. 2. Loosen (but do not remove) the wheel lug nuts by turning them to t...

  • Page 336

    4. Locate the jack as shown. For the front axle, place it under the front lower control arm as shown. For the rear axle, place it under the axle near the wheel to be changed. Ensure the jack is closest to the inside of the wheel when jacking on the rear axle. Do not raise the vehicle until you are s...

  • Page 337

    Warning! Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. 6. Remove the lug nuts and wheel. 7. Position the spare wheel/tire on the vehicle and install the lug nuts with ...

  • Page 338

    Note: tire should be stowed with the “beauty” side up. Storing the tire upside down may result in scratching or damage to the wheel face. Continue winching up the tire until you hear the winch “ratchet” three times. Double check to ensure the tire is snug against the underbody of the vehicle. Damage...

  • Page 339

    5. Connect the other cable, first to the negative terminal of the booster battery and then connect the other end to a non-paint metal surface on the engine of the vehicle with the discharged battery. Make sure you have a good contact on the engine. 6. Start the engine in the vehicle which has the bo...

  • Page 340

    • be sure your vehicle is not touching the jump start vehicle. • observe all battery warnings in section 7 of this manual, while jump starting your vehicle. Warning! Do not attempt to push or tow your vehicle to get it started. Unburned fuel could enter the catalytic converter and, once the engine h...

  • Page 341

    Warning! Stand clear of vehicles when pulling with tow hooks. Tow straps and chains may break, causing serious injury. Towing a disabled vehicle 2wd models only provided the transmission is operable, tow only in n (neutral) at speeds not exceeding 30 mph (48 km/h), for distances of not more than 15 ...

  • Page 343: Maintaining Your Vehicle

    Maintaining your vehicle contents 䡵 3.7l engine . . . . . . . . . . . . . . . . . . . . . . . . . . . 345 䡵 4.7l engine . . . . . . . . . . . . . . . . . . . . . . . . . . . 346 䡵 5.7l engine . . . . . . . . . . . . . . . . . . . . . . . . . . . 347 䡵 onboard diagnostic system — obd ii . . . . . . ....

  • Page 344

    ▫ air conditioner maintenance . . . . . . . . . . . . . 360 ▫ power steering fluid check . . . . . . . . . . . . . . 361 ▫ body lubrication . . . . . . . . . . . . . . . . . . . . . 363 ▫ windshield wiper blades . . . . . . . . . . . . . . . . 363 ▫ windshield washers — front and rear . . . . . 363 ...

  • Page 345

    3.7l engine maintaining your vehicle 345 7.

  • Page 346

    4.7l engine 346 maintaining your vehicle.

  • Page 347

    5.7l engine maintaining your vehicle 347 7.

  • Page 348

    Onboard diagnostic system — obd ii your vehicle is equipped with a sophisticated onboard diagnostic system called obd ii. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide ex...

  • Page 349

    Cap until a ⬙clicking⬙ sound is heard. This is an indication that the gas cap is properly tightened. Press the odometer reset button to turn the message off. If the problem persists, the message will appear the next time the vehicle is started. This might indicate a damaged cap. If the problem is de...

  • Page 350

    4. As soon as you turn your key to the on position, you will see your mil symbol come on as part of a normal bulb check. 5. Approximately 15 seconds later, one of two things will happen: a. The mil will flash for about 10 seconds and then return to being fully illuminated until you turn off the igni...

  • Page 351

    Dealer service your dealer has the qualified service personnel, special tools and equipment to perform all service operations in an expert manner. Service manuals are available which include detailed service information for your vehicle. Refer to these manuals before attempting any procedure yoursel...

  • Page 352

    Could adversely affect the engine or vehicle performance. These items should be inspected if a malfunction is observed or suspected. Engine oil checking oil level to assure proper engine lubrication, the engine oil must be maintained at the correct level. Check the oil level at regular intervals, su...

  • Page 353

    • more than 50% of your driving is at sustained high speeds during hot weather, above 90°f (32°c) • trailer towing • taxi, police, or delivery service (commercial service) • off road or desert operation • if equipped for and operating with e-85 (ethanol) fuel if any of these apply to you, then chang...

  • Page 354

    American petroleum institute (api) engine oil identification symbol this symbol means that the oil has been certified by the american petroleum institute (api). The manufacturer only recommends api certified engine oils that meet the requirements of daimlerchrysler material stan- dard ms-6395. Use m...

  • Page 355

    Materials added to engine oils the manufacturer strongly recommends against the ad- dition of any additives (other than leak detection dyes) to engine oil. Engine oil is an engineered product and it’s performance may be impaired by supplemental addi- tives. Disposing of used engine oil care should b...

  • Page 356

    Belts should be inspected for evidence of cuts, cracks, glazing, or frayed cords and replaced if there is indication of damage which could result in belt failure. Low gen- erator belt tension can cause battery failure. Also, check belt routing to make sure there is no inter- ference between the belt...

  • Page 357

    Caution! Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition. In the event of engine malfunction, particularly involv- ing engine misfire or other apparent loss of perfor- mance, have your vehicle serviced promptly. Contin- ued operation of your veh...

  • Page 358

    To minimize the possibility of catalytic converter damage: • do not shut off the engine or interrupt the ignition when the transmission is in gear and the vehicle is in motion. • do not try to start the engine by pushing or towing the vehicle. • do not idle the engine with any spark plug wires disco...

  • Page 359

    Warning! The air cleaner can provide protection in the case of engine backfire. Do not remove the air cleaner unless it is necessary for repair or maintenance. Make sure that no one is near the engine compart- ment before starting the vehicle with the air cleaner removed. Failure to do so can result...

  • Page 360

    To determine the battery charge, check the battery test indicator (if equipped) on top of the battery. Refer to the illustration. Caution! It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negat...

  • Page 361

    Warning! • use only refrigerants and compressor lubricants approved by the manufacturer for your air condi- tioning system. Some unapproved refrigerants are flammable and can explode, injuring you. Other unapproved refrigerants or lubricants can cause the system to fail, requiring costly repairs. Re...

  • Page 362

    Caution! Do not use automatic transmission fluid (atf) or other types of power steering fluids when servicing the power steering system of this vehicle. Damage to the power steering system can result from the use of the wrong power steering fluid. Checking the power steering fluid level at a defined...

  • Page 363

    Body lubrication locks and all body pivot points, including such items as seat tracks, doors, tailgate and hood hinges, should be lubricated periodically to assure quiet, easy operation and to protect against rust and wear. Prior to the appli- cation of any lubricant, the parts concerned should be w...

  • Page 364

    The fluid reservoir for the windshield washers and the rear window washer is shared. It is located in the front of the engine compartment (on the driver side), and should be checked for fluid level at regular intervals. Fill the reservoir with windshield washer solvent (not antifreeze/coolant) and o...

  • Page 365

    Cooling system warning! You or others can be badly burned by hot antifreeze/ coolant or steam from your radiator. If you see or hear steam coming from under the hood, don’t open the hood until the radiator has had time to cool. Never try to open a cooling system pressure cap when the radiator or coo...

  • Page 366

    Cooling system — drain, flush, and refill at the intervals shown in the appropriate “maintenance schedule,” the system should be drained, flushed, and refilled. If the solution is dirty and contains a considerable amount of sediment, clean and flush with reliable cooling system cleaner. Follow with ...

  • Page 367

    Adding engine coolant your vehicle has been built with an improved antifreeze/ coolant that allows extended maintenance intervals. This antifreeze/coolant can be used up to 5 years or 100,000 miles before replacement. To prevent reducing this ex- tended maintenance period, it is important that you u...

  • Page 368

    The cap should be inspected and cleaned if there is any accumulation of foreign material on the sealing surfaces. Warning! The warning words do not open hot on the cooling system pressure cap are a safety precaution. Never add antifreeze/coolant when the engine is overheated. Do not loosen or remove...

  • Page 369

    When additional antifreeze/coolant is needed to main- tain the proper level, it should be added to the coolant bottle. Do not overfill. Points to remember note: when the vehicle is stopped after a few miles (kilometers) of operation, you may observe vapor coming from the front of the engine compartm...

  • Page 370

    Only the correct type thermostat. Other designs may result in unsatisfactory cooling performance, poor gas mileage, and increased emissions. Hoses and vacuum/vapor harnesses inspect surfaces of hoses and nylon tubing for evidence of heat and mechanical damage. Hard or soft spots, brittle rubber, cra...

  • Page 371

    Brake and power steering system hoses when servicing the vehicle for scheduled maintenance, inspect surface of hoses for evidence of heat and me- chanical damage. Hard and brittle rubber, cracking, tears, cuts, abrasion, and excessive swelling suggest deteriora- tion of the rubber. Particular attent...

  • Page 372

    Fluid reservoir. With disc brakes, fluid level can be expected to fall as the brake pads wear. However, low fluid level may be caused by a leak and a checkup may be needed. Use only manufacturer’s recommended brake fluid, refer to fluids, lubricants, and genuine parts for correct fluid type. Warning...

  • Page 373

    For correct fluid type. It is important that the transmission fluid be maintained at the prescribed level using the recommended fluid. Caution! Using a transmission fluid other than the manufac- turer’s recommended fluid may cause deterioration in transmission shift quality and/or torque converter s...

  • Page 374

    5. Remove the dipstick, wipe it clean and reinsert it until seated. 6. Remove the dipstick again and note the fluid level on both sides. The fluid level should be between the “hot” (upper) reference holes on the dipstick at normal operat- ing temperature. The fluid level is only valid if there is a ...

  • Page 375

    Special additives the manufacturer recommends against the addition of any additives to the transmission. Exception to this policy is the use of special dyes to aid in detecting fluid leaks. Transfer case fluid level check inspect the transfer case for fluid leaks. If a fluid leak is found, the trans...

  • Page 376

    Front/rear axle fluid front axle fluid level check lubricant should be to the bottom of the oil fill hole. Rear axle fluid level check lubricant should be 1/2” (1 cm) below the oil fill hole. Adding fluid add lubricant only at the fill hole and only to the level specified above. Selection of lubrica...

  • Page 377

    Caution! Under frequent heavy-duty driving conditions, change all lubricants and lubricate body compo- nents, all driveline joints and steering linkage more often than in normal service to prevent excessive wear. Appearance care and protection from corrosion protection of body and paint from corrosi...

  • Page 378

    • if insects, tar, or other similar deposits have accumu- lated on your vehicle, use mopar 威 super kleen bug and tar remover to remove. • use mopar威 cleaner wax to remove road film, stains, and to protect your paint finish. Take care never to scratch the paint. • avoid using abrasive compounds and p...

  • Page 379

    • aluminum wheels should be cleaned regularly with a mild soap and water to prevent corrosion. To remove heavy soil, use mopar 威 wheel cleaner or select a nonabrasive, non-acidic cleaner. Do not use scouring pads, steel wool, a bristle brush or metal polishes. Only mopar 威 cleaners are recommended. ...

  • Page 380

    Do not use polishes, oils, cleaning fluids, solvents, deter- gents, or ammonia based cleaners to clean your leather upholstery. Application of a leather conditioner is not required to maintain the original condition. Warning! Do not use volatile solvents for cleaning purposes. Many are potentially f...

  • Page 381

    Seat belt maintenance do not bleach, dye or clean the belts with chemical solvents or abrasive cleaners. This will weaken the fabric. Sun damage will also weaken the fabric. If the belts need cleaning, use mopar 威 total clean, a mild soap solution, or lukewarm water. Do not remove the belts from the...

  • Page 382

    Cavity fuse/color description 1 30 amp pink audio amp (b+) 2 15 amp blue sunroof (b+) 3 10 amp red htd mirror (ebl) 4 20 amp yellow rr pwr out (b+) 5 10 amp red rr hvac (r/o) 6 10 amp red ocm (b+) 7 20 amp yellow door locks (b+) 8 15 amp blue steer col lock (b+) 9 20 amp yellow pwr outlet (b+) 10 10...

  • Page 383

    Underhood fuses (power distribution center) cavity fuse/color description 1 40 amp green hvac blower 2 30 amp pink power outlets 3 30 amp pink rr wiper/ign r/o cavity fuse/color description 4 30 amp pink abs pump 5 50 amp red cabin htr 1 (diesel only) 6 50 amp red asd 7 30 amp pink rr hvac (xk) 8 40...

  • Page 384

    Cavity fuse/color description 20 20 amp yellow pcm batt (gasoline only) 21 30 amp pink abs valves 22 spare 23 20 amp yellow fdcm 24 20 amp yellow fuel pump 25 20 amp yellow fdcm/e-diff. 26 15 amp blue hyd/pcm (diesel only) 27 15 amp blue brake/stop lamps 28 25 amp natural ngc/injectors 29 spare 30 s...

  • Page 385

    Underhood fuses (integrated power module) cavity fuse/color description 1 micro relay wiper on/off rly 2 micro relay wiper hi/lo rly 3 micro relay horn rly cavity fuse/color description 4 micro relay rear fog rly (bux only) 5 micro relay lt t-tow stop/turn rly 6 micro relay rt t-tow stop/turn rly 7 ...

  • Page 386

    Cavity fuse/color description 20 20 amp yellow fcm batt #3 21 20 amp yellow rt t-tow stop/turn 22 30 amp pink fdcm mod 23 50 amp red rad fan 24 mini relay rad fan lo rly 25 micro relay ft fog lamps rly 26 micro relay adjustable pedal rly 27 15 amp blue iod #1 28 20 amp yellow iod #2 (audio) 29 10 am...

  • Page 387

    Replacement bulbs interior lights bulb type glove box light . . . . . . . . . . . . . . . . . . . . . . . . . 194 grab handle light . . . . . . . . . . . . . . . . L002825w5w overhead console reading lights . . . . . . . . . . Vt4976 rear cargo light . . . . . . . . . . . . . . . . . . . . . . . 214...

  • Page 388

    Fluid capacities u.S. Metric fuel (approximate) 20.6 gallons 78 liters engine oil with filter 3.7 liter engine (5w-30, api certified) 5 qts 4.7 liters 4.7 liter engine (5w-30, api certified) 6 qts 5.7 liters 5.7 liter engine (5w-20, api certified) 7 qts 6.6 liters cooling system * 3.7 liter engine (...

  • Page 389

    Fluids, lubricants, and genuine parts engine component fluid, lubricant, or genuine part engine coolant mopar 威 antifreeze/coolant 5 year/100,000 mile formula hoat (hybrid or- ganic additive technology) engine oil (3.7l/4.7l engines) use api certified sae 5w-30 engine oil, meeting the requirements o...

  • Page 390

    Chassis component fluid, lubricant, or genuine part automatic transmission mopar 威 atf+4 automatic transmission fluid transfer case (3.7l engines) mopar 威 atf+4 automatic transmission fluid transfer case (4.7l/5.7l engines) mopar 威 nv 247 transfer case lubricant axle differential (front-rear) mopar ...

  • Page 391: Maintenance Schedules

    Maintenance schedules contents 䡵 emission control system maintenance . . . . . . . . 392 䡵 maintenance schedules . . . . . . . . . . . . . . . . . . . 392 ▫ schedule “b” . . . . . . . . . . . . . . . . . . . . . . . . 395 ▫ schedule “a” . . . . . . . . . . . . . . . . . . . . . . . . 405 8 m a i n t...

  • Page 392

    Emission control system maintenance the “scheduled” maintenance services, listed in bold type must be done at the times or mileages specified to assure the continued proper functioning of the emission control system. These, and all other maintenance services included in this manual, should be done t...

  • Page 393

    • taxi, police, or delivery service (commercial service) • off-road or desert driving • if equipped for and operated with e-85 (ethanol) fuel. Note: most vehicles are operated under the conditions listed for schedule “b.” note: if any of these apply to you, change your engine oil every 3,000 miles (...

  • Page 394

    • check the windshield washer solvent, add as required. Once a month • check the tire pressure and look for unusual wear or damage. • inspect the battery and clean and tighten the terminals as required. • check the fluid levels of the coolant reservoir, brake master cylinder, and transmission, and a...

  • Page 395

    Schedule “b” follow this schedule if you usually operate your vehicle under one or more of the following conditions. • day or night temperatures are below 32°f (0°c) • stop and go driving • excessive engine idling • driving in dusty conditions • short trips of less than 10 miles (16.2 km) • more tha...

  • Page 396

    Miles 3,000 6,000 9,000 12,000 15,000 (kilometers) (5 000) (10 000) (15 000) (20 000) (25 000) change the engine oil and engine oil filter, if not replaced at 3 months. X x x x x rotate the tires. X x check spare tire for proper pressure and correct stowage. X x inspect the engine air cleaner filter...

  • Page 397

    Miles 18,000 21,000 24,000 27,000 30,000 (kilometers) (30 000) (35 000) (40 000) (45 000) (50 000) change the engine oil and engine oil filter, if not replaced at 3 months. X x x x x rotate the tires. X x x check spare tire for proper pressure and correct stowage. X x x inspect the engine air cleane...

  • Page 398

    Miles 33,000 36,000 39,000 42,000 45,000 (kilometers) (55 000) (60 000) (65 000) (70 000) (75 000) change the engine oil and engine oil filter, if not replaced at 3 months. X x x x x rotate the tires. X x check spare tire for proper pressure and correct stowage. X x inspect the engine air cleaner fi...

  • Page 399

    Miles 48,000 51,000 54,000 57,000 60,000 (kilometers) (80 000) (85 000) (90 000) (95 000) (100 000) change the engine oil and engine oil filter, if not replaced at 3 months. X x x x x rotate the tires. X x x check spare tire for proper pressure and correct stowage. X x x inspect the engine air clean...

  • Page 400

    Miles 63,000 66,000 69,000 72,000 75,000 (kilometers) (105 000) (110 000) (115 000) (120 000) (125 000) change the engine oil and engine oil filter, if not replaced at 3 months. X x x x x rotate the tires. X x check spare tire for proper pressure and correct stowage. X x inspect the engine air clean...

  • Page 401

    Miles 78,000 81,000 84,000 87,000 90,000 (kilometers) (130 000) (135 000) (140 000) (145 000) (150 000) change the engine oil and engine oil filter, if not replaced at 3 months. X x x x x rotate the tires. X x x check spare tire for proper pressure and correct stowage. X x x inspect the engine air c...

  • Page 402

    Miles 93,000 96,000 99,000 102,000 105,000 (kilometers) (155 000) (160 000) (165 000) (170 000) (175 000) change the engine oil and engine oil filter, if not replaced at 3 months. X x x x x rotate the tires. X x check spare tire for proper pressure and correct stowage. X x inspect the engine air cle...

  • Page 403

    Miles 108,000 111,000 114,000 117,000 120,000 (kilometers) (180 000) (185 000) (190 000) (195 000) (200 000) change the engine oil and engine oil filter, if not replaced at 3 months. X x x x x rotate the tires. X x x check spare tire for proper pressure and correct stowage. X x x inspect the engine ...

  • Page 404

    Miles 108,000 111,000 114,000 117,000 120,000 (kilometers) (180 000) (185 000) (190 000) (195 000) (200 000) flush and replace the engine coolant/anti-freeze at 120 months, if not replaced at 102,000 miles (170 000 km). X inspection and service should also be performed anytime a malfunction is obser...

  • Page 405

    Schedule “a” miles 6,000 12,000 18,000 24,000 30,000 (kilometers) (10 000) (20 000) (30 000) (40 000) (50 000) [months] [6] [12] [18] [24] [30] change the engine oil and engine oil filter. X x x x x rotate the tires. X x x x x check spare tire for proper pressure and correct stowage. X x x x x inspe...

  • Page 406

    Miles 36,000 42,000 48,000 54, 000 (kilometers) (60 000) (70 000) (80 000) (90 000) [months] [36] [42] [48] [54] change the engine oil and engine oil filter. X x x x rotate the tires. X x x x check spare tire for proper pressure and correct stowage. X x x x inspect the brake linings. X x 406 schedul...

  • Page 407

    Miles 60,000 66,000 72,000 78,000 (kilometers) (100 000) (110 000) (120 000) (130 000) [months] [60] [66] [72] [78] change the engine oil and engine oil filter. X x x x rotate the tires. X x x x check spare tire for proper pressure and correct stowage. X x x x inspect the engine air cleaner filter, ...

  • Page 408

    Miles 84,000 90,000 96,000 102, 000 (kilometers) (140 000) (150 000) (160 000) (170 000) [months] [84] [90] [96] [102] change the engine oil and engine oil filter. X x x x rotate the tires. X x x x check spare tire for proper pressure and correct stowage. X x x x inspect the engine air cleaner filte...

  • Page 409

    Miles 108,000 114,000 120,000 (kilometers) (180 000) (190 000) (200 000) [months] [108] [114] [120] change the engine oil and engine oil filter. X x x rotate the tires. X x x check spare tire for proper pressure and correct stowage. X x x inspect the engine air cleaner filter, and replace if necessa...

  • Page 410

    * this maintenance is not required if the belt was previously replaced. Warning! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the proper equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a...

  • Page 411: Contents

    If you need consumer assistance contents 䡵 suggestions for obtaining service for your vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 412 ▫ prepare for the appointment . . . . . . . . . . . . 412 ▫ prepare a list . . . . . . . . . . . . . . . . . . . . . . . . 412 ▫ be reasonable...

  • Page 412

    Suggestions for obtaining service for your vehicle prepare for the appointment if you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty, discuss additional charges with the service manager. ...

  • Page 413

    Technicians, special tools, and the latest information to assure your vehicle is fixed correctly and in a timely manner. This is why you should always talk to your dealer’s service manager first. Most matters can be resolved with this process. • if for some reason you are still not satisfied, talk t...

  • Page 414

    Customer assistance for the hearing or speech impaired (tdd/tty) to assist customers who have hearing difficulties, the manufacturer has installed special tdd (telecommuni- cation devices for the deaf) equipment at its customer center. Any hearing or speech impaired customer who has access to a tdd ...

  • Page 415

    Warranty information (u.S. Vehicles only) see the warranty information booklet for the terms and provisions of daimlerchrysler’s warranties applicable to this vehicle. Mopar 姞 parts mopar 威 fluids, lubricants, parts, and accessories are available from your dealer. They will help you keep your vehicl...

  • Page 416

    Publication order forms to order the following manuals, you may use either the website or the phone numbers listed below. Visa, mas- tercard, american express, and discover orders are ac- cepted. If you prefer mailing your payment, please call for an order form. Note: a street address is required wh...

  • Page 417

    Call toll free at: • 1–800–890–4038 (u.S.) • 1–800–387–1143 (canada) or visit us on the world wide web at: • www.Techauthority.Daimlerchrysler.Com • www.Daimlerchrysler.Ca/manuals department of transportation uniform tire quality grades the following describes the tire grading categories estab- lish...

  • Page 418

    On specified government test surfaces of asphalt and concrete. A tire marked c may have poor traction perfor- mance. Warning! The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction chara...

  • Page 419: Index

    Index 10

  • Page 420

    Abs (anti-lock brake system) . . . . . . . . . . . . 179,271 adding washer fluid . . . . . . . . . . . . . . . . . . . . . 169 adjustable pedals . . . . . . . . . . . . . . . . . . . . . . . 147 air cleaner, engine (engine air cleaner filter) . . . 358 air conditioner maintenance . . . . . . . . . ....

  • Page 421

    Autostick . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 258 auxiliary electrical outlet (power outlet) . . . . . . 162 auxiliary power outlet . . . . . . . . . . . . . . . . . . . 162 battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 359 emergency starting . . . . . ....

  • Page 422

    Chains, tire . . . . . . . . . . . . . . . . . . . . . . . . . . . . 303 changing a flat tire . . . . . . . . . . . . . . . . . . . . . 332 chart, tire sizing . . . . . . . . . . . . . . . . . . . . . . . . 282 checks, safety . . . . . . . . . . . . . . . . . . . . . . . . . 70,71 child restraint . ...

  • Page 423

    Defroster, rear window . . . . . . . . . . . . . . . . . . . 233 defroster, windshield . . . . . . . . . . . . . . . . 71,234,241 diagnostic system, onboard . . . . . . . . . . . . . . . . 348 dimmer switch, headlight . . . . . . . . . . . . . . . . . 126 dipsticks automatic transmission . . . . . ....

  • Page 424

    Block heater . . . . . . . . . . . . . . . . . . . . . . . . . 255 break-in recommendations . . . . . . . . . . . . . . . . 68 compartment . . . . . . . . . . . . . . . . . . . . . . . . . 346 cooling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 365 exhaust gas caution . . . . . . . . ....

  • Page 425

    Fluid leaks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 fluid level checks automatic transmission . . . . . . . . . . . . . . . 372,373 engine oil . . . . . . . . . . . . . . . . . . . . . . . . . . . 352 power steering . . . . . . . . . . . . . . . . . . . . . . . . 361 fluids, lub...

  • Page 426

    Gear ranges . . . . . . . . . . . . . . . . . . . . . . . . . . . 257 general information . . . . . . . . . . . . . . . . . . . . 24,303 glass cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . 380 gross axle weight rating . . . . . . . . . . . . . . . . . . 313 gross vehicle weight rating...

  • Page 427

    Interior lighting . . . . . . . . . . . . . . . . . . . . . . . . 120 interior lights . . . . . . . . . . . . . . . . . . . . . . . 120,125 intermittent wipers (delay wipers) . . . . . . . . . . . 128 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 jack location . . . . . . ...

  • Page 428

    Dimmer switch, headlight . . . . . . . . . . . . . 122,126 electronic stability program (esp) indicator . . . . . . . . . . . . . . . . . . . . . . . . 140,180,183 electronic throttle control warning . . . . . . . . . 184 fog . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126,185 four-whe...

  • Page 429

    Liftgate, tailgate . . . . . . . . . . . . . . . . . . . . . . . . 18 power door . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 lower anchors and tether for children (latch) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63,64 lubrication, body . . . . . . . . . . . . . . . . . . ...

  • Page 430

    Occupant classification system (ocs) . . . . . . . . . . 48 occupant restraints . . . . . . . . . . . . . . . . . . . . . . . 32 octane rating, gasoline (fuel) . . . . . . . . . . . . . . 305 odometer . . . . . . . . . . . . . . . . . . . . . . . . . . 183,184 trip . . . . . . . . . . . . . . . . . ...

  • Page 431

    Polishing and waxing . . . . . . . . . . . . . . . . . . . . . 378 power distribution center . . . . . . . . . . . . . . . . . . . . . 383 door locks . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 outlet (auxiliary elec...

  • Page 432

    Recorder, event data . . . . . . . . . . . . . . . . . . . . . . 56 recreational towing . . . . . . . . . . . . . . . . . . . . . . 323 shifting into transfer case neutral (n) . . . . . . . 324 shifting out of transfer case neutral (n) . . . . . 326 reformulated gasoline . . . . . . . . . . . . . . ...

  • Page 433

    Reminder . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183 shoulder belt anchorage . . . . . . . . . . . . . . . . . . 37 seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105 adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . 105 cleaning . . . . . . . . ...

  • Page 434

    Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 353 speed control (cruise control) . . . . . . . . . . . . . . 148 speedometer . . . . . . . . . . . . . . . . . . . . . . . . . . . 178 starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 253 automatic transmissi...

  • Page 435

    Inflation pressures . . . . . . . . . . . . . . . . . . . . . 290 jacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 332 life of tires . . . . . . . . . . . . . . . . . . . . . . . . . . 294 load capacity . . . . . . . . . . . . . . . . . . . . . 285,286 pressure monitor system (tpms)...

  • Page 436

    Transmission automatic . . . . . . . . . . . . . . . . . . . . . . . . 256,372 maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . 372 range indicator . . . . . . . . . . . . . . . . . . . . . . . 184 shifting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 256 transmitter batt...

  • Page 437

    Windows power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 windshield defroster . . . . . . . . . . . . . . . . 71,234,241 windshield washers . . . . . . . . . . . . . . . . . . . . . . 127 fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 363 windshield wiper b...

  • Page 438

    438 index.

  • Page 439: Notes

    Notes.

  • Page 440: Notes

    Notes.