1. DL manuals
  2. Jeep
  3. Automobile
  4. 2006 Grand Cherokee
  5. Owner's Manual

Jeep 2006 Grand Cherokee Owner's Manual

Summary of 2006 Grand Cherokee

  • Page 1

    Table of contents section page 1 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 things to know before starting your vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 3 understanding the fe...

  • Page 3: Introduction

    Introduction contents 䡵 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 ▫ roll over warning . . . . . . . . . . . . . . . . . . . . . 5 䡵 how to use this manual . . . . . . . . . . . . . . . . . . 7 䡵 warnings and cautions . . . . . . . . . . . . . . . . . . . 7 䡵 vehicle identi...

  • Page 4

    Introduction thank you for selecting a jeep 威 grand cherokee and welcome to our worldwide family. This is a specialized utility vehicle designed for both on-road and off-road use. It can go places and perform tasks for which conventional two-wheel drive vehicles were not intended. However, on-road r...

  • Page 5

    Roll over warning utility vehicles have a significantly higher roll over rate than other types of vehicles. This vehicle has a higher ground clearance, higher center of gravity, and narrower track than many passenger cars. It is capable of perform- ing better in a wide variety of off-road applicatio...

  • Page 6

    Failure to use driver and passenger seat belts provided is a major cause of severe or fatal injury. In fact, the u.S. Government notes that the universal use of existing seat belts could cut the highway death toll by 10,000 or more each year, and could reduce disabling injuries by 2 million annually...

  • Page 7

    Warning! Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the state of california to cause cancer and birth defects or other reproductive harm. In addition, certain fluids contained in vehicles and certain prod- ucts of component wear contai...

  • Page 8

    Note: it is illegal to remove the vin label. Vehicle modifications / alterations warning! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death. Vehicle identification number 8 introducti...

  • Page 9: Contents

    Things to know before starting your vehicle contents 䡵 a word about your keys . . . . . . . . . . . . . . . . . .12 ▫ ignition key . . . . . . . . . . . . . . . . . . . . . . . . . .12 ▫ key-in-ignition reminder . . . . . . . . . . . . . . . .13 䡵 sentry key immobilizer system . . . . . . . . . . . ...

  • Page 10

    ▫ transmitter battery service . . . . . . . . . . . . . . .23 䡵 security alarm system — if equipped . . . . . . . . .24 ▫ to set the alarm . . . . . . . . . . . . . . . . . . . . . .25 ▫ to disarm the system . . . . . . . . . . . . . . . . . . .25 䡵 liftgate . . . . . . . . . . . . . . . . . . . . ....

  • Page 11

    䡵 safety tips . . . . . . . . . . . . . . . . . . . . . . . . . . . .69 ▫ exhaust gas . . . . . . . . . . . . . . . . . . . . . . . . . .69 ▫ safety checks you should make inside the vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70 ▫ safety checks you should make outside the veh...

  • Page 12

    A word about your keys the keys for your new vehicle are enclosed in a plastic bag with the key code number on it. If you received your keys without the bag, ask your authorized dealer to give you the number. The key code can also be obtained by your authorized dealer from your vehicle invoice. Igni...

  • Page 13

    Key-in-ignition reminder if the driver’s door is opened when the key is in the ignition and not turned to the on position, a chime will sound to remind you to remove the key. Caution! Always remove the key from the ignition, and lock all doors when leaving the vehicle unattended. Sentry key immobili...

  • Page 14

    If the skim indicator light comes on during normal vehicle operation (it has been running for longer than 10 seconds) a fault has been detected in the electronics and the vehicle should be serviced as soon as possible. Note: • the sentry key immobilizer system is not compatible with remote starting ...

  • Page 15

    At the time of purchase, the original owner is provided with a four digit pin number. This number is required for dealer replacement of keys. Duplication of keys may be performed at an authorized dealer or by using the customer key programming procedure. This procedure consists of programming a blan...

  • Page 16

    General information the sentry key immobilizer system complies with fcc rules part 15 and with rss-210 of industry canada. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference that may be received, includ...

  • Page 17

    Warning! When leaving the vehicle always remove the key from the ignition lock, and lock your vehicle. Do not leave children unattended in the vehicle, or with access to an unlocked vehicle. Unsupervised use of vehicle equipment may cause severe personal inju- ries and death. Caution! An unlocked ve...

  • Page 18

    Warning! Avoid trapping anyone in the vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child protection locks are engaged. Child lock control 18 things to know before starting your vehicle.

  • Page 19

    Power door locks a door lock switch is on each front door panel. Press this switch to lock or unlock the doors. If the plunger is down when the door is closed, the door will lock. Therefore, make sure the keys are not inside the vehicle before closing the door. If you press the door lock switch whil...

  • Page 20

    Automatic unlock on exit feature — only available if auto lock is enabled this feature will unlock all the doors when the driver’s door is opened if the vehicle is stopped and in p (park) or n (neutral). Refer to “electronic vehicle information center (evic) — customer programmable features” in sect...

  • Page 21

    Note: if desired, the system can be programmed to unlock all doors on the first press of the “unlock” button. Refer to “remote unlock driver’s door 1st” in the personal settings section of the “electronic vehicle infor- mation center (evic)”, or simply follow these steps: 1. Press and hold the “lock...

  • Page 22

    Warning! Driving with the flipper glass open can allow poi- sonous exhaust gases into your vehicle. You and your passengers could be injured by these fumes. Keep the flipper glass closed when you are operating the vehicle. Using the panic alarm to turn the panic alarm feature on or off, press and ho...

  • Page 23

    2. While the “unlock” button is pressed, (after 4 seconds) press the “lock” button. Release both buttons. The “flash lights on lock/unlock” feature can be reactivated by repeating this procedure. General information this device complies with part 15 of the fcc rules and rss 210 of industry canada. O...

  • Page 24

    1. With the transmitter buttons facing down, remove the small screw, and separate the two halves of the transmit- ter. Make sure not to damage the rubber gasket during removal. 2. Remove and replace the battery. Avoid touching the new battery with your fingers. Skin oils may cause battery deteriorat...

  • Page 25

    To set the alarm the alarm will set when you use the remote keyless entry transmitter to lock the doors and liftgate or when you use the power door lock switch while the door is open. After all the doors are locked and closed, a red light (located in the instrument cluster) will flash rapidly for ab...

  • Page 26

    Liftgate to open the liftgate, pull up (squeeze) on the handle and lift. Manually unlocking the vehicle doors with the plunger or a key in the lock cylinder will not unlock the liftgate. Warning! Driving with the liftgate open can allow poisonous exhaust gases into your vehicle. You and your pas- se...

  • Page 27

    Warning! To avoid injury stand back when opening. Glass will automatically rise. Once the liftgate flipper glass has been opened, connec- tion to the rear window wiper is interrupted, preventing activation of the rear wiper blade while the flipper glass is open. Note: if a power malfunction to the p...

  • Page 28

    Power windows the power window controls are located on the driver’s door trim panel. There is a single switch on the front passenger door/rear doors which operates the front passenger/rear passenger door windows. The window controls will operate only when the ignition switch is in the on or accessor...

  • Page 29

    Auto down both the driver and front passenger window switch has an “auto down” feature. Press the window switch past the first detent, release, and the window will go down automatically. To cancel the “auto down” movement, operate the switch in either the up or down direction and release the switch....

  • Page 30

    Warning! There is no anti-pinch protection when the window is almost closed. Be sure to clear all objects from the window before closing. Resetting the auto-up feature should the auto-up feature stop working the window probably needs to be reset. To reset auto-up: pull the window switch up and close...

  • Page 31

    Open or partially open positions. This is a normal occur- rence and can be minimized. If the buffeting occurs with the sunroof open, adjust the sunroof opening to minimize the buffeting. Occupant restraints some of the most important safety features in your vehicle are the restraint systems. These i...

  • Page 32

    Research has shown that seat belts save lives, and they can reduce the seriousness of injuries in a collision. Some of the worst injuries happen when people are thrown from the vehicle. Seat belts reduce the possibility of ejection and the risk of injury caused by striking the inside of the vehicle....

  • Page 33

    Lap/shoulder belt operating instructions 1. Enter the vehicle and close the door. Sit back and adjust the seat. 2. The seat belt latch plate is above the back of your seat. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to make the belt go aroun...

  • Page 34

    3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” warning! A belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt ...

  • Page 35

    4. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap portion, pull up a bit on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision. Wa...

  • Page 36

    6. To release the belt, push the red button marked press on the buckle. The belt will automatically retract to its stowed position. If necessary, slide the latch plate down the webbing to allow it to retract fully. Warning! A frayed or torn belt could rip apart in a collision and leave you with no p...

  • Page 37

    As a guide, if you are shorter than average, you will prefer a lower position, and if you are taller than average, you’ll prefer a higher position. When you release the anchorage, try to move it up or down to make sure that it is locked in position. Automatic locking mode — if equipped in this mode,...

  • Page 38

    Warning! • the belt and retractor assembly must be replaced if the seat belt assembly “automatic locking re- tractor” feature or any other seat belt function is not working properly when checked according to the procedures in the service manual. • failure to replace the belt and retractor assembly c...

  • Page 39

    Chime and flash the seat belt warning light for 96 seconds or until the driver or front passenger seat belt is buckled. The enhanced warning system (beltalert) will be reactivated if the driver or front passenger seat belt is unbuckled for more than 10 seconds and the vehicle speed is greater than 5...

  • Page 40

    Seat belts and pregnant women we recommend that pregnant women use the seat belts throughout their pregnancy. Keeping the mother safe is the best way to keep the baby safe. Pregnant women should wear the lap part of the belt across the thighs and as snug across the hips as possible. Keep the belt lo...

  • Page 41

    Driver and front passenger supplemental restraint systems (srs) this vehicle has airbags for both the driver and right front passenger as a supplement to the seat belt restraint systems. The driver’s front airbag is mounted in the steering wheel. The passenger side airbag is mounted in the instrumen...

  • Page 42

    This vehicle may also be equipped with window bags to protect the driver, front, and rear passengers sitting next to a window. If the vehicle is equipped with window bags, they are located above the side windows. Their covers are also labeled srs/airbag. Note: airbag covers may not be obvious in the...

  • Page 43

    Warning! • do not put anything on or around the front airbag covers or attempt to manually open them. You may damage the airbags and you could be injured because the airbags are no longer functional. These protective covers for the airbag cushions are designed to open only when the airbags are infla...

  • Page 44

    If your vehicle is so equipped, the window bag on the crash side of the vehicle is triggered in moderate to severe side collisions. In certain types of collisions, both the front and side airbags may be triggered. But even in collisions where the airbags work, you need the seat belts to keep you in ...

  • Page 45

    4. If your vehicle has window bags, do not lean against the door or window, airbags will inflate forcefully into the space between you and the door. 5. If the airbag system in this vehicle needs to be modified to accommodate a disabled person, contact the customer center. Phone numbers are provided ...

  • Page 46

    Airbag system components the airbag system consists of the following: • occupant restraint control module • airbag warning light • driver airbag • passenger airbag • side curtain airbags above side windows (if equipped) • side remote acceleration sensors (if equipped) • steering wheel and column • i...

  • Page 47

    The orc also monitors the readiness of the electronic parts of the system whenever the ignition switch is in the start or on positions. These include all of the items listed above except the knee bolster, the instru- ment panel, and the steering wheel and column. If the key is in the lock position, ...

  • Page 48

    Note: children 12 years and under should always ride buckled up in a rear seat in an appropriate child restraint. • the passenger airbag disable (pad) indicator light (an amber light located in the center of the instrument panel) tells the driver and front passenger when the front passenger airbag i...

  • Page 49

    The “pad indicator light” should not be illuminated when teenagers, most children in a forward-facing child restraint or booster seats, most children that can properly wear the vehicle’s seat belt, and when an adult passenger is properly seated in the front passen- ger seat. In this case, the airbag...

  • Page 50

    The ocs classifies an occupant using weight sensors mounted in the base of the front passenger seat. Any weight on the seat will be sensed by the system. Objects hanging on the seat or other passengers pushing down on the seat will also be sensed. The weight of an adult will cause the system to turn...

  • Page 51

    Both the “pad indicator light” and the “airbag warning light” are illuminated to show that the passenger airbag is turned off until the fault is cleared. If an object is lodged under the seat and interferes with operation of the weight sensors, a fault will occur which turns on both the “pad indicat...

  • Page 52

    • your vehicle has four weight sensors located between the seat and the floor pan. The weight sensors measure applied weight and transfers that information to the ocm. • the side impact srs side curtain airbags are de- signed to activate only in certain side or rollover collisions. When the orc (wit...

  • Page 53

    • do not modify the front seat center console or center position seat in any way. • do not use prior or future model year seat covers not designated for the specific model being repaired. Al- ways use the correct seat cover specified for the vehicle. • do not replace the seat cover with an aftermark...

  • Page 54

    Note: a frontal collision that is not severe enough to need airbag protection will not activate the system. This does not mean something is wrong with the airbag system. If you do have a collision which deploys the airbags, any or all of the following may occur: • the nylon airbag material may somet...

  • Page 55

    Warning! Deployed airbags and seat belt pretensioners cannot protect you in another collision. Have the airbags, seat belt pretensioner, and seat belt retractor assem- bly, replaced by an authorized dealer as soon as possible. Also, have the occupant classification system serviced as well. Enhanced ...

  • Page 56

    Airbag warning light you will want to have the airbag system ready to inflate for your protection in an impact. The airbag system is designed to be maintenance free. If any of the following occurs, have an authorized dealer service the system promptly: • does not come on during the 6 to 8 seconds af...

  • Page 57

    Provided to the custodial entity upon request. General data that does not identify particular vehicles or crashes may be released for incorporation in aggregate crash databases, such as those maintained by the us govern- ment and various states. Data of a potentially sensitive nature, such as would ...

  • Page 58

    Child restraint everyone in your vehicle needs to be buckled up all the time — babies and children, too. Every state in the united states and all canadian provinces require that small children ride in proper restraint systems. This is the law, and you can be prosecuted for ignoring it. Children 12 y...

  • Page 59

    • the infant carrier is only used rearward-facing in the vehicle. It is recommended for children who weigh up to about 20 lbs (9 kg). “convertible” child seats often have a higher weight limit in the rearward-facing direction than infant carriers do, so they can be used rearward-facing by children w...

  • Page 60

    Standards. The manufacturer also recommends that you try a child restraint in the vehicle seats where you will use it before you buy it. • the restraint must be appropriate for your child’s weight and height. Check the label on the restraint for weight and height limits. • carefully follow the instr...

  • Page 61

    • if the belt still cannot be tightened, or if pulling and pushing on the restraint loosens the belt, disconnect the latch plate from the buckle, turn the buckle around, and insert the latch plate into the buckle again. If you still cannot make the child restraint secure, try a different seating pos...

  • Page 62

    Children too large for booster seats children who are large enough to wear the shoulder belt comfortably, and whose legs are long enough to bend over the front of the seat when their back is against the seat back, should use the lap/shoulder belt in a rear seat. • make sure that the child is upright...

  • Page 63

    Kits or retro-fit kits. You are urged to take advantage of all the available attachments provided with your child re- straint in any vehicle. Note: when using the latch attaching system to install a child restraint, please ensure that all seat belts not being used for occupant restraints are stowed ...

  • Page 64

    Installing the latch-compatible child restraint system we urge that you carefully follow the directions of the manufacturer when installing your child restraint. Not all child restraint systems will be installed as described here. Again, carefully follow the installation instructions that were provi...

  • Page 65

    Many, but not all restraint systems will be equipped with separate straps on each side, with each having a hook or connector for attachment to the lower anchorage and a means of adjusting the tension in the strap. Forward- facing toddler restraints and some rear-facing infant restraints will also be...

  • Page 66

    Warning! Improper installation of a child restraint to the latch anchorages can lead to failure of an infant or child restraint. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint. Installing child restraints using th...

  • Page 67

    If the belt still can’t be tightened, or if by pulling and pushing on the restraint loosens the belt, you may need to do something more. Disconnect the latch plate from the buckle, turn the buckle around, and insert the latch plate into the buckle again. If you still can’t make the child restraint s...

  • Page 68

    Warning! An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchor positions directly behind the child seat to secure a child restraint top tether strap. Transporting pets airbags deploying in the front seat could harm your pet. An...

  • Page 69

    A new engine may consume some oil during its first few thousand miles (kilometers) of operation. This should be considered as a normal part of the break-in and not interpreted as an indication of difficulty. Safety tips exhaust gas warning! Exhaust gases can injure or kill. They contain carbon monox...

  • Page 70

    Safety checks you should make inside the vehicle seat belts inspect the belt system periodically, checking for cuts, frays and loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Seat belt assemblies must be replaced after an accident if they have been d...

  • Page 71

    Fluid leaks check area under vehicle after overnight parking for fuel, coolant, oil or other fluid leaks. Also, if gasoline fumes are detected, the cause should be located and corrected immediately. Things to know before starting your vehicle 71 2.

  • Page 73: Contents

    Understanding the features of your vehicle contents 䡵 mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78 ▫ inside day/night mirror . . . . . . . . . . . . . . . . .78 ▫ inside automatic dimming mirror — if equipped . . . . . . . . . . . . . . . . . . . . . . . . . .79 ▫ exterior...

  • Page 74

    ▫ things you should know about your uconnect™ system . . . . . . . . . . . . . . . . . . . . 101 䡵 seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106 ▫ front manual seat adjustment . . . . . . . . . . . . 106 ▫ front seat adjustment — recline . . . . . . . . . . 107 ▫ manual l...

  • Page 75

    ▫ automatic headlight system — if equipped . . 122 ▫ smartbeams — if equipped . . . . . . . . . . . . . . 123 ▫ instrument panel and interior lights . . . . . . . 124 ▫ daytime running lights — canada only . . . . 125 ▫ lights-on reminder . . . . . . . . . . . . . . . . . . . 125 ▫ fog lights — if e...

  • Page 76

    ▫ enable/disable the rear park assist system . . 143 ▫ service the rear park assist system . . . . . . . . 144 ▫ cleaning the rear park assist system . . . . . . 144 䡵 adjustable pedals — if equipped . . . . . . . . . . . 146 䡵 electronic speed control . . . . . . . . . . . . . . . . . . 148 ▫ to ac...

  • Page 77

    ▫ pinch protect override . . . . . . . . . . . . . . . . . 160 ▫ venting sunroof - express . . . . . . . . . . . . . . . 160 ▫ sunshade operation . . . . . . . . . . . . . . . . . . . 161 ▫ wind buffeting . . . . . . . . . . . . . . . . . . . . . . . 161 ▫ sunroof maintenance . . . . . . . . . . . ....

  • Page 78

    Mirrors inside day/night mirror the mirror should be adjusted to center on the view through the rear window. A two-point pivot system allows for horizontal and vertical adjustment of the mirror. The mirror should be adjusted while set in the day position (toward windshield). Annoying headlight glare...

  • Page 79

    Inside automatic dimming mirror — if equipped this mirror automatically adjusts for annoying headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light next to the button will indicate when the dimming feature is activated. ...

  • Page 80

    Exterior mirrors folding feature all exterior mirrors are hinged and may be moved either forward or rearward to resist damage. The hinges have three detent positions; full forward, full rearward, and normal. Outside mirrors to receive maximum benefit, adjust the outside mirrors to center on the adja...

  • Page 81

    Power remote control outside mirrors the power mirror switch is located on the driver’s door trim panel next to the power door lock switch. A rotary knob selects the left mirror, right mirror, or off position. After selecting a mirror move the knob in the same direction you want the mirror to move. ...

  • Page 82

    Power folding outside mirrors — if equipped turn the power mirror switch knob all the way down to the left or right to fold in the mirrors. Turn the knob back upward to the left mirror, right mirror, or off (center) position to the normal (unfolded) driving position. Both mirrors will always move to...

  • Page 83

    Sun visor extension (if equipped) this feature has a pull out extension on the sun visor for increased coverage. Hands–free communication (uconnect™) — if equipped uconnect™ is a voice-activated, hands-free, in- vehicle communications system. Uconnect™ allows you to dial a phone number with your cel...

  • Page 84

    The uconnect™ phonebook enables you to store up to 32 names and four numbers per name. Each language has a separate 32 name phonebook accessible only in that language. This system is driven through your blue- tooth™ hands-free profile cellular phone. Uconnect™ features bluetooth™ technology - the gl...

  • Page 85

    Headset profile), you may not be able to use any ucon- nect™ features. Refer to your cellular service provider or the phone manufacturer for details. The uconnect™ system is fully integrated with the vehicle’s audio system. The volume of the uconnect™ system can either be adjusted from the radio vol...

  • Page 86

    Voice command tree refer to “voice tree” at the end of this section. Help command if you need assistance at any prompt or if you want to know what your options are at any prompt, say ⬙help⬙ following the voice on beep. The uconnect™ system will play all the options at any prompt if you ask for help....

  • Page 87

    The following are general phone to uconnect™ system pairing instructions: • press the ’phone’ button to begin. • after the ⬙ready⬙ prompt and the following beep, say ⬙setup phone pairing.⬙ • when prompted, after the voice on beep, say ⬙pair a phone. ⬙ • you will be asked to say a four-digit pin numb...

  • Page 88

    Dial by saying a number • press the ’phone’ button to begin. • after the ⬙ready⬙ prompt and the following beep, say ⬙dial.⬙ • system will prompt you to say the number you want call. • for example, you can say ⬙234-567-8901.⬙ the phone number that you enter must be of valid length and combination. Th...

  • Page 89

    Add names to your uconnect™ phonebook note: adding names to phonebook is recommended when vehicle is not in motion. • press the “phone” button to begin. • after the ⬙ready⬙ prompt and the following beep, say ⬙phonebook new entry.⬙ • when prompted, say the name of the new entry. Use of long names hel...

  • Page 90

    • you will then be asked for the name of the phonebook entry that you wish to edit. • next, choose the number designation (home, work, mobile, or pager) that you wish to edit. • when prompted, recite the new phone number for the phonebook entry that you are editing. After you are finished editing an...

  • Page 91

    • after you enter the name, the uconnect™ system will ask you which designation you wish to delete: home, work, mobile or pager. Say the designation you wish to delete. • note that only the phonebook entry in the current language is deleted. After confirmation, the phonebook entries will be de- lete...

  • Page 92

    Phone call features the following features can be accessed through the uconnect™ system if the feature(s) are available on your cellular service plan. For example, if your cellular service plan provides three-way calling, this feature can be accessed through the uconnect™ system. Check with your cel...

  • Page 93

    Second call is in progress. To go back to the first call, refer to ⬙toggling between calls.⬙ to combine two calls, refer to ⬙conference call.⬙ place/retrieve a call from hold to put a call on hold, press the ⬘phone’ button until you hear a single beep which will indicate that the call has been place...

  • Page 94

    Redial • press the ’phone’ button to begin. • after the ⬙ready⬙ prompt and the following beep, say ⬙redial.⬙ • the uconnect™ system will call the last number that was dialed on your cellular phone. Note: this may not be the last number dialed from the uconnect™ sys- tem. Call continuation call conti...

  • Page 95

    • after the ⬙ready⬙ prompt and the following beep, say the name of the language you wish to switch to (english, espanol, or francais, if so equipped). • continue to follow the system prompts to complete language selection. After selecting one of the languages, all prompts and voice commands will be ...

  • Page 96

    Your phone must be turned on and paired to the ucon- nect™ system to allow use of this vehicle feature in emergency situations when the cell phone has network coverage and stays paired to the uconnect™ system. Towing assistance if you need towing assistance, • press the ’phone’ button to begin. • af...

  • Page 97

    When calling a number with your uconnect™ system that normally requires you to enter in a touch-tone sequence on your cellular phone keypad, you can push the ’voice recognition’ button and say the sequence you wish to enter followed by the word ⬙send.⬙ for example, if required to enter your pin numb...

  • Page 98

    Dialing using the cellular phone keypad you can dial a phone number with your cellular phone keypad and still use the uconnect™ system (while dialing via the cell phone keypad, the user must exercise caution and take precautionary safety measures). By dialing a number with your paired bluetooth™ cel...

  • Page 99

    Information service when using at&t wireless service, dialing to phone number ⬙#121,⬙ you can access voice activated automated system to receive news, weather, stocks, traffic, etc. Related information. Advanced phone connectivity transfer call to and from cellular phone the uconnect™ system allows ...

  • Page 100

    Select another cellular phone this feature allows you to select and start using another phone with the uconnect™ system. The phone must have been previously paired to the uconnect™ system that you want to use it with. • press the ’phone’ button to begin. • after the ⬙ready⬙ prompt and the following ...

  • Page 101

    Things you should know about your uconnect™ system voice recognition (vr) • always wait for the beep before speaking. • speak normally, without pausing, just as you would speak to a person sitting approximately eight (8) feet away from you. • make sure that no one other than you is speaking during a...

  • Page 102

    • you can say ⬙o⬙ (letter ⬙o⬙) for ⬙0⬙ (zero). ⬙800⬙ must be spoken ⬙eight-zero-zero.⬙ • even though international dialing for most number combinations is supported, some shortcut dialing number combinations may not be supported. Far end audio performance • audio quality is maximized under: • low-to...

  • Page 103

    Understanding the features of your vehicle 103 3.

  • Page 104

    104 understanding the features of your vehicle.

  • Page 105

    Understanding the features of your vehicle 105 3.

  • Page 106

    North american english primary alternate(s) zero oh add location add new all all of them confirmation prompts confirmations prompts delete a name delete language select language list names list all list paired phones list phones pager beeper phone pairing pairing phonebook phone book return to main ...

  • Page 107

    Front seat adjustment — recline to adjust the seatback, lift the lever located on the outboard side of the seat, lean back, and release the lever at the desired position. To return the seatback, lift the lever, lean forward, and release the lever. Warning! Do not ride with the seatback reclined so t...

  • Page 108

    Manual lumbar support adjustment the manual lumbar support adjustment lever is located on the right side of the driver’s seat and on the left side of the passenger’s seat. Moving the lumbar control lever fore and aft increases or decreases the lumbar support. Head restraints head restraints can redu...

  • Page 109

    8 - way driver’s power seat the driver’s power seat switches are located on the outboard side of the driver’s seat lower side trim. The bottom switch controls up/down, forward/rearward, and tilt adjustment. The top switch controls the seatback recline adjustment. Adjustable head restraints power sea...

  • Page 110

    4 - way passenger’s power seat — if equipped the front passenger’s power seat switches are located on the outboard side of the passenger seat lower side trim. The bottom switch controls forward/rearward adjust- ment. The top switch controls the seatback recline adjust- ment. Note: the 4 - way seat d...

  • Page 111

    When high-temperature heating is selected, the heaters provide a boosted heat level during the first four minutes of operation after heating is activated. The heat output then drops to the normal high-temperature level. If high-level heating is selected, the system will automati- cally switch to the...

  • Page 112

    Note: do not fold the rear seat down with the center seat belt buckled. 2. Fold the rear seat completely forward. Note: the automatic folding rear head restraints will lower as the seat is folded down. To raise rear seat raise the rear seatback and lock it into place. If interfer- ence from the carg...

  • Page 113

    Storage — rear seat armrest (if equipped) the rear seat may be equipped with a center storage armrest. Press the latch and lift the top of the armrest to access the storage bin. Rear seat armrest armrest storage bin understanding the features of your vehicle 113 3.

  • Page 114

    Driver memory seat — if equipped once programmed, the memory buttons 1 and 2 on the driver’s door panel can be used to recall the driver’s seat, driver’s outside mirror, adjustable brake and accelerator pedals, and radio station preset settings. Your remote keyless entry transmitters can also be pro...

  • Page 115

    Setting memory positions and linking remote keyless entry transmitter to memory note: each time the set (s) button and a numbered button (1 or 2) are pressed, you erase the memory settings for that button and store a new one. 1. Insert the ignition key and turn the ignition switch to the on position...

  • Page 116

    11. Select ⬙remote linked to memory⬙ in the electronic vehicle information center (evic) and enter ⬙yes⬙ or select ⬙use factory settings⬙ from the evic and enter ⬙yes⬙. Refer to “electronic vehicle information center (evic) — customer programmable features” in section 4 for more information. 12. Rep...

  • Page 117

    To disable a transmitter linked to memory 1. Turn the ignition switch to the off position and remove the key. 2. Press and release memory button number 1. The system will recall any memory settings stored in position 1. Wait for the system to complete the memory recall before continuing to step 3. 3...

  • Page 118

    There are two possible easy exit and easy entry adjust- ments available: • the seat cushion will move rearward approximately 2.5 inches (60 mm) if the starting position of the seat is greater than or equal to 3.75 inches (90 mm) forward of the rear seat stop when the key is removed from the ignition...

  • Page 119

    To open and close the hood to open the hood, pull the release lever inside your vehicle located below the instrument panel and in front of the driver’s door. Then, reach under the hood, move safety latch to the left, and lift the hood. To prevent possible damage, do not slam the hood to close it. Us...

  • Page 120

    Warning! If the hood is not fully latched, it could fly up when the vehicle is moving and block your forward vision. Be sure all hood latches are fully latched before driving. Lights interior lighting the interior lighting consists of courtesy lights mounted below the instrument panel, an overhead c...

  • Page 121

    Multi-function control lever the multi-function control lever controls the operation of the headlights, turn signals, headlight beam selection, instrument panel light dimming, passing light, interior courtesy/dome lights, and optional fog lights. Front map/reading lights multi-function control lever...

  • Page 122

    Turn signal auto-mode — if equipped tap the multi-function control lever once and the turn signal (left or right) will flash 3 times, and automatically turn off. Battery saver feature—exterior/interior lights if the multi-function control lever is left in the interior light position, parking light p...

  • Page 123

    This system performs two functions. With the engine running and the multi-function control lever in the a (auto) position, the headlights will turn on and off based on the surrounding light levels. Headlights on automatically with wipers if your vehicle is equipped with automatic headlights it also ...

  • Page 124

    To activate 1. Select “auto headlamp low/high beams? — low/ high beam.” refer to “evic — customer programmable features” in section 4 of this manual. 2. Turn the end of the multi-function control lever to the a (auto) headlight position. Note: this system will not activate until the vehicle is at or...

  • Page 125

    “off” position the instrument panel lighting is at the lowest light level and may not be suitable for night driving. Daytime running lights — canada only the high beam headlights come on at a low intensity level whenever the engine is running, and the transmis- sion in not in the p (park) position. ...

  • Page 126

    Turn signals move the multi-function control lever up or down and the arrows on each side of the instrument cluster will flash to show proper operation of the front and rear turn signal lights. You can signal a lane change by moving the lever partially up or down. High beam switch pull the multi-fun...

  • Page 127

    Note: always remove any build-up of snow that prevents the windshield wiper blades from returning to the off position. If the windshield wiper switch is turned off and the blades cannot return to the off position, damage to the wiper motor may occur. To use the washer, pull the lever toward you and ...

  • Page 128

    Mist use this feature when weather conditions make occa- sional usage of the wipers necessary. Pull down and release the control lever for a single wiping cycle. Speed sensitive intermittent wiper system use one of the five intermittent wiper speeds when weather conditions make a single wiping cycle...

  • Page 129

    The sensitivity of the system can be adjusted with the multi-function lever. Wiper delay position 1 is the least sensitive, and wiper delay position 5 is the most sensi- tive. Setting 3 should be used for normal rain conditions. Settings 1 and 2 can be used if the driver desires less wiper sensitivi...

  • Page 130

    The rain sensing system has protection features for the wiper blades and arms, and will not operate under the following conditions: • low ambient temperature — when the ignition is first turned on, the rain sensing system will not operate until the wiper switch is moved, vehicle speed is greater tha...

  • Page 131

    Warning! Tilting the steering wheel column while the vehicle is moving is dangerous. Without a stable steering column, you could lose control of the vehicle and have an accident. Adjust the tilting mechanism only while the vehicle is stopped. Be sure it is locked before driving. Electronic brake con...

  • Page 132

    Warning! Abs (anti-lock brake system) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevail- ing road conditions. Abs cannot prevent accidents, including those resulting from excessive speed in turns, driving on very slippery surf...

  • Page 133

    Bas (brake assist system) the bas is designed to optimize the vehicle’s braking capability during emergency braking maneuvers. The system detects an emergency braking situation by sens- ing the rate and amount of brake application and then applies optimum pressure to the brakes. This can help reduce...

  • Page 134

    Erm (electronic rollover mitigation) this system anticipates the potential for wheel lift by monitoring the driver’s steering wheel input and the speed of the vehicle. When erm determines that the rate of change of the steering wheel angle and vehicles speed are sufficient to potentially cause wheel...

  • Page 135

    Esp (electronic stability program) this system enhances directional control and stability of the vehicle under various driving conditions. Esp cor- rects for over/under steering of the vehicle by applying the brake of the appropriate wheel to assist in counter- acting the over/under steer condition....

  • Page 136

    Warning! Esp (electronic stability program) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions. Esp cannot prevent acci- dents, including those resulting from excessive speed in turns, driving on very slipper...

  • Page 137

    Or gravel conditions and more wheel spin than esp would normally allow is required to gain traction. To turn esp on again, momentarily depress the ⬙esp control switch ⬙. This will restore the normal “esp on” mode of operation. Note: to improve the vehicle’s traction when driving with snow chains, or...

  • Page 138

    Vehicle information center (evic). Refer to “electronic vehicle information center (evic)” in section 4 of this manual. (see page 187 for more information.) to turn esp on again, momentarily depress the ⬙esp control switch⬙. This will restore the normal “esp on” mode of operation. Note: the “esp off...

  • Page 139

    30 mph (48 km/h). At 30 mph (48 km/h), the normal esp stability function returns but tcs remains off. When the vehicle speed drops below 25 mph (40 km/h), the esp system shuts off. Esp is off at low vehicle speeds in 4wd low range so that it will not interfere with off-road driving but esp function ...

  • Page 140

    Warning! With the esp switched off, the enhanced vehicle stability offered by esp and erm are unavailable. In an emergency evasive maneuver, the esp and erm systems will not engage to assist in maintaining stability. The “full off” mode is intended for off- highway or off-road use only. Esp/bas warn...

  • Page 141

    Rear park assist system— if equipped the rear park assist system provides visual and audible indications of the distance between the rear fascia and the detected obstacle when backing up. Refer to the warning section and note section for limitations of this system and recommendations. The rear park ...

  • Page 142

    Rear park assist warning display the rear park assist warning display, located in the headliner near the flipper glass, provides both visual and audible warnings to indicate the distance between the rear fascia and the detected obstacle. When the ignition is changed to the run/on position, the warni...

  • Page 143

    When the detected obstacle is about 11.8 inches (30 cm) from the rear fascia, the warning display will actuate a continuous tone for about 10 seconds, and it will turn on all 8 leds, including both red leds, on the correspond- ing side of the display. The radio will be muted while the tone is actuat...

  • Page 144

    When the switch is pressed to disable the system, the instrument cluster will display the ⬙park assist dis- abled ⬙ message. Refer to “electronic vehicle informa- tion center (evic)” in section 4 of this manual. When the shifter is changed to r (reverse) and the system is disabled, the instrument cl...

  • Page 145

    Caution! • the rear park assist system is only a parking aid and it is unable to recognize every obstacle, in- cluding small obstacles. Parking curbs might be temporarily detected or not detected at all. Ob- stacles located above or below the sensors will not be detected when they are in close proxi...

  • Page 146

    Note: clean all four rear park assist sensors regularly, taking care not to scratch or damage them. The sensors must not be covered with ice, snow, slush, mud, dirt or debris. Failure to do so can result in the system not working properly. The system might not detect an ob- stacle behind the fascia ...

  • Page 147

    Press the left side of the button to move the pedals rearward (toward the driver). Press the right side of the button to move the pedals forward (away from the driver). • the pedals can be adjusted with the ignition off. • the pedals can be adjusted while driving. • the pedals cannot be adjusted whe...

  • Page 148

    Caution! Do not place any article under the adjustable pedal’s or impede its ability to move as it may cause damage to the pedal controls. Pedal travel may become limited if movement is stopped by an obstruction in the adjustable pedal’s path. Electronic speed control when engaged, this device takes...

  • Page 149

    To set at a desired speed when the vehicle has reached the desired speed, press and release the set button. Release the accelerator and the vehicle will operate at the selected speed. To deactivate a soft tap on the brake pedal, normal braking, or pressing the cancel button will deactivate the speed...

  • Page 150

    To accelerate for passing depress the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed. Note: when driving uphill, at elevations above 2,000 feet (610 meters), or when the vehicle is heavily loaded (especially when towing) the vehicle may slow b...

  • Page 151

    Warning! To help keep your vehicle under control, do not use speed control under these conditions: • when it is not possible to keep your vehicle at a set speed. • on slippery roads, such as on snow or ice. • in heavy or varying traffic volume, in traffic that varies in speed, or on winding roads. •...

  • Page 152

    Courtesy/reading lights at the forward end of the console are two courtesy/ reading lights. Press the lens to turn these lights on. Press a second time to turn the lights off. The lights also turn on when a front door or rear door is opened. The lights will also turn on when the unlock button on the...

  • Page 153

    Warning! A moving garage door can cause injury to people and pets in the path of the door. People or pets could be seriously or fatally injured. Only use this transceiver with a garage door opener that has a “stop and reverse” feature as required by federal safety stan- dards. This includes most gar...

  • Page 154

    Programming homelink note: when programming a garage door opener, it is advised to park outside the garage. It is also recom- mended that a new battery be placed in the hand-held transmitter of the device being programmed to homelink for quicker training and accurate transmis- sion of the radio-freq...

  • Page 155

    2. Position the end of your hand-held transmitter 1-3 inches (3-8 cm) away from the homelink buttons. 3. Simultaneously press and hold both the homelink button that you want to train and the hand-held trans- mitter buttons. Do not release the buttons until step 4 has been completed. Note: some gate ...

  • Page 156

    Note: to program the remaining two homelink but- tons, begin with ⬙programming⬙ step two. Do not repeat step one. Note: if your hand-held transmitter appears to pro- gram the universal transceiver, but your garage door does not operate using the transmitter and your garage door opener was manufactur...

  • Page 157

    Canadian programming/gate programming canadian radio-frequency laws require transmitter sig- nals to ⬙time-out⬙ (or quit) after several seconds of transmission which may not be long enough for homelink to pick up the signal during programming. Similar to this canadian law, some u.S. Gate operators a...

  • Page 158

    • press and hold the two outer homelink buttons and release only when the evic display shows “chan- nels cleared” (after 20 seconds). Release both buttons. Do not hold for longer that 30 seconds. Homelink is now in the train (or learning) mode and can be programmed at any time beginning with ⬙pro- g...

  • Page 159

    Homelink 威 is a trademark owned by johnson controls, inc. Power sunroof — if equipped the power sunroof switch is located between the sun visors on the overhead console. Warning! • never leave children in a vehicle, with the keys in the ignition switch. Occupants, particularly unat- tended children,...

  • Page 160

    Opening sunroof - express press the switch rearward and release, and the sunroof will open automatically from any position. The sunroof will open fully, then stop automatically. This is called express open. During express open operation, any movement of the sunroof switch will stop the sunroof. Clos...

  • Page 161

    Sunshade operation the sunshade can be opened manually. However, the sunshade will open automatically as the sunroof opens. Note: the sunshade cannot be closed if the sunroof is open. Wind buffeting wind buffeting can be described as the perception of pressure on the ears or a helicopter type sound ...

  • Page 162

    Power outlet to the right of the convenience tray (lower center of instrument panel) is an outlet for electrically powered accessories. Pull lightly on the tab of the plastic cover to access the outlet. The rear power outlet (if equipped) is located in the left rear cargo area. Front power outlet re...

  • Page 163

    The power outlets are a direct feed from the battery so they receive power whether the ignition is in the on or off position. All accessories connected to this outlet should be re- moved or turned off when the vehicle is not in use to protect the battery against discharge. Caution! Electrical outlet...

  • Page 164

    Cup holders in the center console there are two cup holders for the front seat passengers. Note: the cup holder insert is removable, from the console, for cleaning. It can be reinstalled with the larger cup depression towards the passenger seat, but the top surface will not be flush with the console...

  • Page 165

    Cargo area features cargo light the cargo area light is activated by opening the liftgate, opening any door, or by rotating the dimmer control on the multi-function control lever to the extreme top posi- tion. If all doors are closed and only the liftgate is open, pushing on the cargo light lens sur...

  • Page 166

    Retractable cargo area cover — if equipped note: the purpose of this cover is for privacy, not to secure loads. It will not prevent cargo from shifting or protect passengers from loose cargo. To cover the cargo area: 1. Grasp the cover at the center handle. Pull it over the cargo area. 2. Insert the...

  • Page 167

    Warning! In an accident a cargo cover loose in the vehicle could cause injury. It could fly around in a sudden stop and strike someone in the vehicle. Do not store the cargo cover on the cargo floor or in the passenger compartment. Remove the cover from the vehicle when taken from its mounting. Do n...

  • Page 168

    Warning! Cargo tie-down hooks are not safe anchors for a child seat tether strap. In a sudden stop or collision a hook could pull loose and allow the child seat to come loose. A child could be badly injured. Use only the anchors provided for child seat tethers. Warning! The weight and position of ca...

  • Page 169

    Warning! To help protect against personal injury, passengers should not be seated in the rear cargo area. The rear cargo space is intended for load carrying purposes only, not for passengers, who should sit in seats and use seat belts. Cargo load floor the panel in the load floor is reversible for a...

  • Page 170

    1. Flip up pull loop(s) so they are perpendicular (straight up) to the top surface of the tray. 2. Pull up on loop(s) and twist 90 degrees, so they are parallel to the slotted hole in tray. 3. Lift tray over loop(s), and reposition tray. 4. Pull up on loop(s) and twist 90 degrees, so they are perpen...

  • Page 171

    If the rear wiper is operating when the ignition is turned off, the wiper will automatically return to the “park” position. If the liftgate flipper glass is open, connection to the rear window wiper is interrupted preventing activation of the rear wiper blade. When the liftgate flipper glass is clos...

  • Page 172

    Note: the optional cross rails have seven specific locations identified by a feature on both the side rail and the cross rail. Cross rails must be secured in one of the seven detent locations on the side rail to prevent move- ment with a sudden stop. For improved windnoise performance when cross rai...

  • Page 173

    Warning! Cargo must be securely tied before driving your vehicle. Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in personal injury or property damage. Follow the roof rack “cautions” when carrying cargo on your roof rack. Understanding the features of your ...

  • Page 175: Contents

    Understanding your instrument panel contents 䡵 instrument panel and interior controls . . . . . . . 178 䡵 instrument cluster . . . . . . . . . . . . . . . . . . . . . . 179 䡵 instrument cluster description . . . . . . . . . . . . . 180 䡵 electronic vehicle information center — if equipped . . . . . ...

  • Page 176

    ▫ operation instructions - (cd mode for cd audio play) . . . . . . . . . . . 208 ▫ load/eject button (cd mode for cd audio play) . . . . . . . . . . . 209 ▫ notes on playing mp3 files . . . . . . . . . . . . . 211 ▫ operation instructions - (cd mode for mp3 audio play) . . . . . . . . . . 214 ▫ load...

  • Page 177

    ▫ selecting satellite mode in ref radios . . . . . . 228 ▫ selecting satellite mode in raq radios . . . . . 228 ▫ selecting a channel . . . . . . . . . . . . . . . . . . . . 228 ▫ storing and selecting pre-set channels . . . . . . 229 ▫ using the pty (program type) button — if equipped . . . . . . ....

  • Page 178

    Instrument panel and interior controls 178 understanding your instrument panel.

  • Page 179

    Instrument cluster understanding your instrument panel 179 4.

  • Page 180

    Instrument cluster description 1. Speedometer indicates vehicle speed. 2. Brake warning light the brake warning light will come on when the ignition is first turned on, and stay on briefly as a bulb check. If the bulb does not come on during starting, have the bulb re- paired promptly. If the light ...

  • Page 181

    Engine start. If the bulb does not come on when turning the key from off to on, have the condition checked promptly. Certain conditions such as a loose or missing gas cap, poor fuel quality, etc. May illuminate the light after engine start. The vehicle should be serviced if the light stays on throug...

  • Page 182

    If the abs light is on, the brake system should be serviced as soon as possible to restore the benefits of anti-lock brakes. If the abs light does not turn on when the ignition switch is turned to the on position, have the light inspected by an authorized dealer. 8. Tachometer the red segments indic...

  • Page 183

    Prevailing road conditions. The “esp/tcs indicator light” will flash any time the esp or tcs is active and helping to improve vehicle stability. If the “esp/tcs indicator light” is on solid, the esp system has been turned off by the driver or a temporary condition exists that will not allow full esp...

  • Page 184

    13. Temperature gauge the temperature gauge shows engine coolant tempera- ture. Any reading within the normal range indicates that the engine cooling system is operating satisfactorily. The gauge pointer will likely indicate a higher tempera- ture when driving in hot weather, up mountain grades, or ...

  • Page 185

    16. Electronic stability program (esp) warning light/brake assist system (bas) warning light — if equipped the esp/bas warning light in the instrument cluster comes on when the ignition switch is turned to the “on” position. The light should go out with the engine running. If the esp/ bas warning li...

  • Page 186

    U.S. Federal regulations require that upon transfer of vehicle ownership, the seller certify to the purchaser the correct mileage that the vehicle has been driven. There- fore, if the odometer reading is changed during repair or replacement, be sure to keep a record of the reading before and after t...

  • Page 187

    25. Voltage warning light this light monitors the electrical system voltage. The light should turn on momentarily as the engine is started. If the light stays on or turns on while driving, it indicates a problem with the charging system. Immediate service should be obtained. 26. Low fuel warning lig...

  • Page 188

    • turn signal on • perform service • key not programmed — damaged key • key not programmed — invalid key • key not programmed — exceeded key pro- gram limit • programming active — new key pro- grammed • service security key • invalid key — try alternate key • driver/passenger door open (with graphic...

  • Page 189

    • liftglass/hood open (with graphic) • washer fluid low (with graphic) • check gauges • auto highbeam on • auto highbeam off • park assist disabled • service park assist system • transmission over temp • check shift procedure • service 4wd system • 4wd system in neutral • low brake fluid level • war...

  • Page 190

    • service tire press system • left front low pressure (premium tpm sys- tem only) • right front low pressure (premium tpm sys- tem only) • left rear low pressure (premium tpm system only) • right rear low pressure (premium tpm sys- tem only) • spare low pressure (premium tpm system only) customer pr...

  • Page 191

    Language? When in this display you may select one of three lan- guages for all display nomenclature, including the trip computer functions. Press the step button while in this display selects english, espanol, or francais. As you continue the displayed information will be shown in the selected langu...

  • Page 192

    Remote unlock driver’s door 1st? When this feature is selected only the driver’s door will unlock on the first press of the remote keyless entry unlock button and require a second press to unlock the remaining locked doors and liftgate. When remote unlock all doors is selected all of the doors and t...

  • Page 193

    Headlamp delay when this feature is selected the driver can choose, when exiting the vehicle, to have the headlamps remain on for 30, 60, or 90 seconds, or not remain on. Pressing the step button when in this display will select 30, 60, 90, or off. Illuminated approach? When this feature is selected...

  • Page 194

    Front wipers rain sense? (available with rain sensing wipers only) pressing the step button when in this display will select “manual” or “rain sense.” service interval when this feature is selected a service interval between 2,000 (3 200 km) and 6,000 miles (10 000 km) in 500 mile (800 km) increment...

  • Page 195

    Compass/temperature/trip computer this display provides the outside temperature, one of the eight compass headings to indicate the direction the vehicle is facing, and vehicle trip information. The com- pass and temperature display is the normal display. When the c/t button is pressed the compass/ t...

  • Page 196

    Warning! Even if the display still reads a few degrees above 32°f ( 0°c), the road surface may be icy, particularly in woods or on bridges. Drive carefully under such conditions to prevent an accident and possible per- sonal injury or property damage. Compass/temperature display 196 understanding yo...

  • Page 197

    Trip computer this feature, located in the instrument cluster, displays the following information when the display is in the “compass/temperature” mode and the step button is pressed: step button press the step button to cycle through all of the compass/mini-trip computer displays. Step button under...

  • Page 198

    Reset button press the reset button to reset the display you are in. Press and hold the reset button (for 2 seconds) to reset all of the displays. Average fuel economy shows the average fuel economy since the last reset. When the fuel economy is reset, the display will read “reset” or show dashes fo...

  • Page 199

    Elapsed time shows the accumulated ignition on time since the last reset. Tire pressure display — if equipped shows the current pressure of all 4 road tires. Note: tires heat up during normal driving conditions. Heat will cause the tire pressure to increase from 2 to 6 psi (14 to 41 kpa) during norm...

  • Page 200

    Note: to ensure proper compass calibration, make sure the compass variance is properly set before manu- ally calibrating the compass. Refer to variance map. To put into a calibration mode start the engine and leave the transmission in the p (park) position. Set the display to “compass/temperature.” ...

  • Page 201

    To set the variance: turn the ignition on and set the display to “compass/temperature.” press the c/t but- ton for approximately 5 seconds. The last variance zone number will be displayed. Press and hold the step button for 1 second to select the new variance zone and press the reset button to resum...

  • Page 202

    Two types of signals there are two basic types of radio signals... Am or amplitude modulation, in which the transmitted sound causes the amplitude, or height, of the radio waves to vary... And fm or frequency modulation, in which the frequency of the wave is varied to carry the sound. Electrical dis...

  • Page 203

    Operating instructions - radio mode note: the ignition switch must be in the on or acc position to operate the radio. Power switch/volume control (rotary) press the on/vol control to turn the radio on. Press the on/vol a second time to turn off the radio. Electronic volume control the electronic vol...

  • Page 204

    Seek button (radio mode) press and release the seek button to search for the next listenable station in either am/fm or satellite (if equipped) mode. Press the right side of the button to seek up and the left side to seek down. The radio will remain tuned to the new station until you make another se...

  • Page 205

    2. Adjust the hours by turning the right side tune / audio control. 3. After the hours are adjusted, press the right side tune / audio control to set the minutes. The minutes will begin to blink. 4. Adjust the minutes using the right side tune / audio control. 5. To exit, press any button/knob or wa...

  • Page 206

    Press the rotary tune control a fifth time and fade will display. Turn the tune control to the left or right to adjust the sound level between the front and rear speak- ers. Press the rotary tune control again to exit setting tone, balance and fade. Rnd/pty button (radio mode) pressing this button o...

  • Page 207

    Nostalgia nostalgia oldies oldies personality personality public public rhythm and blues rhythm_and_blues religious music religious_music religious talk religious_talk rock rock soft soft soft rock soft_rock soft rhythm and blues soft_r_&_b sports sports talk talk top 40 top_40 weather weather by pr...

  • Page 208

    Display window. Each button can be set for set 1 and set 2 in both am and fm. This allows a total of 12 am,12 fm and 12 satellite (if equipped) stations to be stored into push-button memory. The stations stored in set 2 memory can be selected by pressing the push-button twice. Every time a preset bu...

  • Page 209

    If you insert a disc with the ignition on and the radio on, the unit will switch from radio to cd mode and begin to play when you insert the disc. The display will show the disc number, the track number, and index time in minutes and seconds. Play will begin at the start of track 1. Seek button (cd ...

  • Page 210

    Radio display will show ⬙loading disc⬙ when the disc is loading, and “reading disc” when the radio is reading the disc. Load / ejt - eject press the load/ ejt button and the push- button with the corresponding number where the cd was loaded and the disc will unload and move to the entrance for easy ...

  • Page 211

    Am/fm button (cd mode for cd audio play) switches the radio to the radio mode. Rnd/pty button (random play button) (cd mode for cd audio play) press this button while the cd is playing to activate random play. This feature plays the selections on the compact disc in random order to provide an intere...

  • Page 212

    • maximum number of files: 255 • maximum number of folders: 100 • maximum number of characters in file/folder names: • level 1: 12 (including a separator ⬙.⬙ and a 3-character extension) • level 2: 31 (including a separator ⬙.⬙ and a 3-character extension) multisession disc formats are supported by ...

  • Page 213

    Mpeg specifi- cation sampling fre- quency (khz) bit rate (kbps) mpeg-1 audio layer 3 48, 44.1, 32 320, 256, 224, 192, 160, 128, 112, 96, 80, 64, 56, 48, 40, 32 mpeg-2 audio layer 3 24, 22.05, 16 160, 128, 144, 112, 96, 80, 64, 56, 48, 40, 32, 24, 16, 8 id3 tag information for artist, song title and ...

  • Page 214

    Operation instructions - (cd mode for mp3 audio play) seek button (cd mode for mp3 play) pressing the right side of the seek button plays the next mp3 file. Pressing the left side of the seek button plays the beginning of the mp3 file. Pressing the button within the first ten seconds plays the previ...

  • Page 215

    Msg or info button (cd mode for mp3 play) press and msg or info button while playing mp3 disc. The radio scrolls through the following tag information: song title, artist, file name, and folder name (if avail- able). Press the msg or info button once more to return to ⬙elapsed time⬙ priority mode. P...

  • Page 216

    Operating instructions - satellite radio mode (if equipped) refer to the satellite radio section of the owner’s manual. Operating instructions - video entertainment system (ves 威) (if equipped) refer to separate video entertainment system (ves 威) guide. Sales code ref — am/fm/cd (single disc) radio ...

  • Page 217

    Power switch/volume control (rotary) press the on/vol control to turn the radio on. Press the on/vol a second time to turn off the radio. Electronic volume control the electronic volume control turns continuously (360 degrees) in either direction without stopping. Turning the volume control to the r...

  • Page 218

    Scan button (radio mode) pressing the scan button causes the tuner to search for the next listenable station, in either am, fm or satellite (if equipped) frequencies, pausing for 5 seconds at each listenable station before continuing to the next. To stop the search, press scan a second time. Pscan b...

  • Page 219

    Am/fm button (radio mode) press the button to select am or fm modes. Setting the tone, balance, and fade press the rotary tune control and bass will be dis- played. Turn the tune control to the right or left to increase or decrease the bass tones. Press the rotary tune control a second time and mid ...

  • Page 220

    The set button twice and set 2 will show in the display window. Each button can be set for set 1 and set 2 in both am and fm. This allows a total of 12 am,12 fm and 12 satellite (if equipped) stations to be stored into push- button memory. The stations stored in set 2 memory can be selected by press...

  • Page 221

    Seek button (cd mode) press the right side of the seek button for the next track on the cd. Press the left side of the button to return to the beginning of the current track, or return to the beginning of the previous track if the cd is within the first 10 seconds of the current selection. Mute butt...

  • Page 222

    Rnd/set button (random play button) (cd mode) press this button while the cd is playing to activate random play. This feature plays the selections on the compact disc in random order to provide an interesting change of pace. Press the seek button to move to the next randomly selected track. Press an...

  • Page 223

    Mute button (auxiliary mode) press the mute button to cancel the sound from the speakers. ⬙mute⬙ will be displayed. Press the mute button a second time and the sound from the speakers will return. Rotating the volume control or turning off the ignition will also return the sound from the speakers. S...

  • Page 224

    Operating instructions - satellite radio — if equipped refer to the satellite radio section of the owner’s manual. Sales code rec — am/fm/cd (6–disc) radio with navigation system satellite navigation radio with cd player with mp3 capability (rec) - combines a global-positioning system-based navigati...

  • Page 225

    Clock setting procedure refer to “setting the clock” under ”system settings” in your navigation user’s manual for details about setting the clock. Video entertainment system (sales code xrv) — if equipped the optional ves™ (video entertainment system) con- sists of a dvd player and lcd (liquid cryst...

  • Page 226

    The lcd screen is located on the headliner behind the front seats. Satellite radio — if equipped satellite radio uses direct satellite to receiver broadcast- ing technology to provide clear digital sound, coast to coast. The subscription service provider is sirius™ satel- lite radio. This service of...

  • Page 227

    System activation to activate your sirius satellite radio service, call the toll-free number 888-539-7474, or visit the sirius web site at www.Sirius.Com. Please have the following informa- tion available when activating your system: 1. The electronic serial number/sirius identification number (esn/...

  • Page 228

    Esn/sid access with raq radios with the ignition switch in the accessory position and the radio off, press the cd eject and time buttons simultaneously for 3 seconds. All twelve esn/sid num- bers will be displayed. The radio will exit the esn/sid mode when any other button is pushed, the ignition is...

  • Page 229

    Appear in the display between each channel change. Press the scan button a second time to stop the search. Note: channels that may contain objectionable content can be blocked. Contact sirius customer care at 888-539- 7474 to discuss options for channel blocking or unblock- ing. Please have your esn...

  • Page 230

    Satellite antenna to ensure optimum reception on vehicles available with a luggage rack, do not place items on the roof around the rooftop antenna location. Metal objects placed within the line of sight of the antenna will cause decreased perfor- mance. Larger luggage items should be placed as far f...

  • Page 231

    The right hand control is a rocker type switch with a push-button in the center and controls the volume and mode of the sound system. Pressing the top of the rocker switch will increase the volume and pressing the bottom of the rocker switch will decrease the volume. Pressing the center button will ...

  • Page 232

    The center button on the left side rocker switch has no function for a single disc cd player. However, when a multiple disc cd player is equipped on the vehicle, the center button will select the next available cd in the player. Cd/dvd disc maintenance to keep the cd/dvd discs in good condition, tak...

  • Page 233

    Climate controls climate controls — manual air conditioning the controls for the heating/air conditioning and venti- lation system in this vehicle consist of a series of rotary knobs. These comfort controls can be set to obtain desired interior conditions. The instrument panel features four dual-van...

  • Page 234

    Electric rear window defroster press this button to turn on the rear window defroster and the heated side mirrors (if equipped). An led in the button will illuminate to indicate the rear window defroster is on. The defroster automatically turns off after about 10 minutes of opera- tion. Caution! To ...

  • Page 235

    Mode selection the mode selector (the right rotary knob) can be placed in several posi- tions. Dots between each of the mode selections identify intermediate modes that allow the occupants to fine tune airflow distribution. Defrost air is directed to the windshield through the outlets at the base of...

  • Page 236

    Panel air flows through the outlets located in the instru- ment panel. Air flows through the registers in the back of the center console to the rear seat passengers. These registers can be closed to block airflow. Recirculation the recirculation feature can be selected with the mode control knob. Yo...

  • Page 237

    Operating tips understanding your instrument panel 237 4.

  • Page 238

    Automatic temperature control — if equipped the infrared dual-zone climate control system auto- matically maintains the interior comfort level desired by the driver and passenger. This is accomplished by a dual sun-sensor in the top of the instrument panel, and an infrared sensor located in the face...

  • Page 239

    Lo auto position should be used for front seat occu- pants only. The hi auto position should be used when more air flow is desired, or when rear seat occupants are present. Dial in the comfort setting you would like the system to maintain by rotating the driver’s or passenger’s control knob. Once th...

  • Page 240

    Debris due to the climate control sensor’s location. Mud on the windshield may also cause poor operation of this system. • to provide you with maximum comfort in the auto- matic mode, during cold start-ups the blower fan will remain off until the engine warms up. However, the fan will engage immedia...

  • Page 241

    Understanding your instrument panel 241 4.

  • Page 242

    Note: regardless of the type of operation, when a temperature knob is set to the full clockwise or full counterclockwise position, the system will deliver full hot or full cold air out of the ducts, respectively. The operator can override the auto mode setting and select the direction of the air by ...

  • Page 243

    Air flows through the registers in the back of the center console, and under the front seats to the rear seat passengers. These registers can be closed to block airflow. The center console outlets deliver conditioned air while the floor outlets deliver heated air. • panel air flows through the outle...

  • Page 244

    This button can be used to block out smoke, odors, dust, high humidity, or if rapid cooling is desired. The recirculation mode should only be used temporarily. The button includes an led that illuminates, which indicates that the recircula- tion mode is active. You may use this feature separately. N...

  • Page 245

    Vacation storage anytime you store your vehicle, or keep it out of service (i.E. Vacation) for two weeks or more, run the air condi- tioning system at idle for about five minutes in the fresh air and high blower setting. This will insure adequate system lubrication to minimize the possibility of com...

  • Page 247: Starting And Operating

    Starting and operating contents 䡵 starting procedures . . . . . . . . . . . . . . . . . . . . . 251 ▫ normal starting . . . . . . . . . . . . . . . . . . . . . . 251 ▫ extreme cold weather (below –20°f (–29°c) . . 252 ▫ if engine fails to start . . . . . . . . . . . . . . . . . 252 ▫ after starting ...

  • Page 248

    䡵 anti-lock brake system . . . . . . . . . . . . . . . . . . 269 䡵 power steering . . . . . . . . . . . . . . . . . . . . . . . . 272 䡵 on-road driving tips . . . . . . . . . . . . . . . . . . . 273 䡵 off-road driving tips . . . . . . . . . . . . . . . . . . . 274 ▫ when to use 4wd low range — if eq...

  • Page 249

    䡵 tire pressure monitor system (tpms) . . . . . . . . 294 ▫ base system . . . . . . . . . . . . . . . . . . . . . . . . . 294 ▫ premium system . . . . . . . . . . . . . . . . . . . . . . 296 ▫ general information . . . . . . . . . . . . . . . . . . . 300 䡵 tire chains . . . . . . . . . . . . . . . ....

  • Page 250

    ▫ towing – 2wd models . . . . . . . . . . . . . . . . . 320 ▫ towing — quadra-trac i (single-speed transfer case) 4wd models . . . . . . . . . . . . . . . . . . . . 320 ▫ towing — quadra–trac ii /quadra–drive ii 4wd models . . . . . . . . . . . . . . . . . . . . . . . . 321 䡵 snow plow . . . . . . ....

  • Page 251

    Starting procedures before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. Warning! Do not leave children or animals inside parked vehicles in hot weather. Interior heat build up may cause serious injury or death. The gear selector must be...

  • Page 252

    Warning! Never pour fuel or other flammable liquids into the throttle body air inlet opening in an attempt to start the vehicle. This could result in a flash fire causing serious personal injury. Extreme cold weather (below –20°f (–29°c) to insure reliable starting at these temperatures, use of an e...

  • Page 253

    After starting the idle speed will automatically decrease as the engine warms up. Caution! Long periods of engine idling, especially at high engine speeds can cause excessive exhaust tempera- tures which can damage your vehicle. Do not leave your vehicle unattended with the engine running. Engine bl...

  • Page 254

    Transmission shifting 5–speed automatic transmission the electronically controlled transmission provides a precise shift schedule. The transmission electronics are self-calibrating; therefore, the first few shifts on a new vehicle, may be somewhat abrupt. This is a normal condition, and precision sh...

  • Page 255

    Warning! It is dangerous to shift the selector lever out of p (park) or n (neutral) if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in reverse. You could lose control of the vehicle and hit someone or somet...

  • Page 256

    Warning! Unintended movement of a vehicle could injure those in and near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, you should apply the park brake, shift the transmission into p (park), and remove the key from the igniti...

  • Page 257

    Shifter is in the d (drive) position, allowing the selection of the desired top gear. For example, if the driver shifts the transmission into 3 (third gear), the transmission will never shift above third gear, but can shift down to 2 (second) or 1 (first), when needed. Warning! Do not downshift for ...

  • Page 258

    Note: if the vehicle is started in extremely cold tem- peratures, the transmission may not shift into overdrive and will automatically select the most desirable gear for operation at this temperature. Normal operation will resume when the transmission fluid temperature has risen to a suitable level....

  • Page 259

    Overheating or failure due to excessive shifting. When operating in “tow/haul” mode, the transmission will shift to 3rd gear and 4th will be enabled under steady cruise conditions. The “tow/haul” light will illuminate in the instru- ment cluster to indicate when the switch has been activated. Pressi...

  • Page 260

    4. Wait approximately 10 seconds, then restart the en- gine. 5. Move the shift lever to the desired gear range. If the problem is no longer detected, the transmission will return to normal operation. If the problem persists, p (park), r (reverse), and n (neutral) will continue to operate. Only secon...

  • Page 261

    Cause damage to the transmission. The torque converter will refill within five seconds of shifting from park into any other gear position. Rocking the vehicle if the vehicle becomes stuck in snow, sand, or mud, it can often be moved by a rocking motion. Move the gear selector rhythmically between d ...

  • Page 262

    Four-wheel drive operation quadra-trac i 姞 operating instructions/precautions — if equipped the quadra-trac i 威 is a single speed (hi range only) transfer case which provides convenient full-time 4–wheel drive. No driver interaction is required. This transfer case divides engine torque almost evenly...

  • Page 263

    Road surfaces only. Driving in the 4 low position on dry hard surfaced roads may cause increased tire wear and damage to driveline components. When operating your vehicle in 4 low, the engine speed is approximately three times that of the 4 hi position at a given road speed. Take care not to overspe...

  • Page 264

    N (neutral) neutral — disengages both the front and rear driveshafts from the powertrain. To be used for flat towing behind another vehicle. Refer to “recreational towing” in sec- tion 5 of this manual. 4 low four wheel drive low range — low speed 4 wheel drive. Locks the front and rear driveshafts ...

  • Page 265

    4 low to 4 hi with the vehicle at speeds of 0 to 3 mph (0 to 5 km/h), key on or engine running, shift the transmission into n (neutral), and raise the transfer case t-handle. The “4wd low indicator lamp” in the instrument cluster will flash and go out when the shift is complete. Release the t-handle...

  • Page 266

    Neutral (n) shift procedure 1. Key on, engine off. 2. Vehicle stopped, with foot on brake. 3. Place transmission in n (neutral). 4. Hold down n (neutral) “pin” switch (with a pen, etc.) for 4 seconds until the led lamp by the switch starts to blink indicating shift in progress. Lamp will stop blinki...

  • Page 267

    Note: if shift conditions/interlocks are not met, a “check shift procedures” message will flash from the evic (electronic vehicle information center). Refer to “electronic vehicle information center (evic)” in section 4 of this manual. (see page 187 for more information.) quadra-drive ii 姞 system — ...

  • Page 268

    Note: the instrument cluster “brake warning light” indicates only that the parking brake is applied. It does not indicate the degree of brake application. Before leaving the vehicle parked on a hill, you must make sure the parking brake is fully applied and place the gear selector in the p (park) po...

  • Page 269

    Warning! • leaving children unattended in a vehicle is dan- gerous for a number of reasons. A child or others could be injured. Children should be warned not to touch the parking brake or the gear selector lever. Don’t leave the keys in the ignition. A child could operate power windows, other contro...

  • Page 270

    Warning! Significant over or under inflation of tires, or mixing sizes of tires or wheels on the vehicle can lead to loss of braking effectiveness. The anti-lock brake system conducts a low-speed self- test at about 12 mph (20 km/h). If you have your foot lightly on the brake while this test is occu...

  • Page 271

    Warning! • the anti-lock brake system (abs) cannot pre- vent the natural laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency beyond that afforded by the condition of the vehicle brakes and tires or the traction afforded. • the abs cannot prevent accidents, ...

  • Page 272

    • do not “ride” the brakes by resting your foot on the pedal. This could overheat the brakes and result in unpredictable braking action, longer stopping dis- tances, or brake damage. • when descending mountains or hills, repeated brak- ing can cause brake fade with loss of braking control. Avoid rep...

  • Page 273

    Note: increased noise levels at the end of the steering wheel travel are considered normal and does not indicate that there is a problem with the power steering system. Upon initial start-up in cold weather, the power steering pump may make noise for a short period of time. This is due to the cold, ...

  • Page 274

    Conventional 2-wheel drive vehicles any more than low- slung sports cars are designed to perform satisfactorily in off-road conditions. If at all possible, avoid sharp turns or abrupt maneuvers. As with other vehicles of this type, failure to operate this vehicle correctly may result in loss of cont...

  • Page 275

    Caution and maintain a steady controlled speed less than 5 mph (8 km/h) in deep water to minimize wave effects. Flowing water if the water is swift flowing and rising (as in storm run-off) avoid crossing until the water level recedes and/or the flow rate is reduced. If you must cross flowing water a...

  • Page 276

    Hill climbing note: before attempting to climb a hill, determine the conditions at the crest and/or on the other side. Before climbing a steep hill, shift the transmission to a lower gear and shift the transfer case to 4wd low. Use first gear and 4wd low for very steep hills. If you stall or begin t...

  • Page 277

    Traction downhill shift the transmission into a low gear and the transfer case to 4wd low range. Let the vehicle go slowly down the hill with all four wheels turning against engine compression drag. This will permit you to control the vehicle speed and direction. When descending mountains or hills, ...

  • Page 278

    Warning! Abrasive material in any part of the brakes may cause excessive wear or unpredictable braking. You might not have full braking power when you need it to prevent an accident. If you have been operating your vehicle in dirty conditions, get your brakes checked and cleaned as necessary. • if y...

  • Page 279

    Tire safety information tire markings note: • p (passenger)-metric tire sizing is based on u.S. Design standards. P-metric tires have the letter “p” molded into the sidewall preceding the size designation. Ex- ample: p215/65r15 95h. • european metric tire sizing is based on european design standards...

  • Page 280

    Tire sizing chart example: size designation: p = passenger car tire size based on u.S. Design standards ⴖ....Blank....ⴖ = passenger car tire based on european design standards lt = light truck tire based on u.S. Design standards t = temporary spare tire 31 = overall diameter in inches (in) 215 = sec...

  • Page 281

    Example: service description: 95 = load index —a numerical code associated with the maximum load a tire can carry. H = speed symbol —a symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions. —the maximum speed corresp...

  • Page 282

    Tire identification number (tin) the tin may be found on one or both sides of the tire however the date code may only be on one side. Tires with white sidewalls will have the full tin including date code located on the white sidewall side of the tire. Look for the tin on the outboard side of black s...

  • Page 283

    Tire loading and tire pressure tire placard location note: the proper cold tire inflation pressure is listed on either the face of the driver’s door or the driver’s side “b” pillar. Tire and loading information placard this placard tells you important information about the: 1) number of people that ...

  • Page 284

    3) the tire size designed for your vehicle 4) the cold tire inflation pressures for the front, rear and spare tires. Loading the vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adher...

  • Page 285

    4. The resulting figure equals the available amount of cargo and luggage load capacity. For example, if “xxx” amount equals 1400 lbs. And there will be five 150 lb. Passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lb. (since 5 x 150 = 750, and 1400 – 750 = 6...

  • Page 286

    286 starting and operating.

  • Page 287

    Warning! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. Tires — general information tire pressure proper tire inflation pressur...

  • Page 288

    2. Economy— improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Under inflation also increases tire rolling resistance and results in higher fuel consump- t...

  • Page 289

    Check tire pressure. Do not make a visual judgement when determining proper inflation. Radial tires may look properly inflated even when they are under inflated. Caution! After inspecting or adjusting the tire pressure al- ways reinstall the valve stem cap–if equipped. This will prevent moisture and...

  • Page 290

    Tire pressures for high speed operation the manufacturer advocates driving at safe speeds within posted speed limits. Where speed limits or condi- tions are such that the vehicle can be driven at high speeds, maintaining correct tire inflation pressure is very important. Increased tire pressure and ...

  • Page 291

    Warning! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause tire dam- age or failure. A tire could explode and injure someone. Do not spin your vehicle’s wheels faster than 35 mph (55 km/h) when you are stuck, and do not let anyone near a spinning wheel no m...

  • Page 292

    Life of tire the service life of a tire is dependent upon varying factors including but not limited to: • driving style • tire pressure • distance driven warning! Tires and spare tire should be replaced after six years, regardless of the remaining tread. Failure to follow this warning can result in ...

  • Page 293

    Warning! • do not use a tire, wheel size or rating other than that specified for your vehicle. Some combina- tions of unapproved tires and wheels may change suspension dimensions and performance charac- teristics, resulting in changes to steering, han- dling, and braking of your vehicle. This can ca...

  • Page 294

    Tires may also cause the vehicle to pull left or right. Alignment will not correct this problem. See your autho- rized dealer for proper diagnosis. Improper alignment will not cause vehicle vibration. Vibration may be a result of tire and wheel out-of- balance. Proper balancing will reduce vibration...

  • Page 295

    The system will consist of tire pressure monitoring sensors attached to each wheel through the valve stem mounting hole, a central receiver module and a “tire pressure monitoring telltale light.” a sensor is located in the spare wheel if the vehicle is equipped with a match- ing full size spare whee...

  • Page 296

    Caution! After inspecting or adjusting the tire pressure al- ways reinstall the valve stem cap. This will prevent moisture and dirt from entering the valve stem, which could damage the wheel rim sensor. Note: • the tpms can inform the driver of a low tire pressure condition. • the tpms is not intend...

  • Page 297

    When a system fault is detected. The flash cycle will repeat every ten minutes or until the fault condition is removed and reset. The tire pressure monitor system (tpms) consists of the following components: • receiver module • 5 wheel sensors (including full size spare tire) • 4 wheel sensor trigge...

  • Page 298

    The following ⬙warnings⬙ will cause a text message to be displayed, an audible chime to sound and the “tire pressure monitoring telltale light” to illuminate. The audible chime will occur once every ignition cycle for each ⬙warning⬙ detected. The “tire pressure monitoring telltale light” will illumi...

  • Page 299

    Caution! The tpms has been optimized for the original equipment tires and wheels. Tpms pressures have been established for the tire size equipped on your vehicle. Undesirable system operation or sensor damage may result when using replacement equip- ment that is not of the same size, type, and/or st...

  • Page 300

    General information this device complies with part 15 of the fcc rules and rss 210 of industry canada. Operation is subject to the following conditions: • this device may not cause harmful interference. • this device must accept any interference received, including interference that may cause undesi...

  • Page 301

    Tire rotation recommendations tires on the front and rear axles of vehicles operate at different loads and perform different steering, handling, and braking functions. For these reasons, they wear at unequal rates, and develop irregular wear patterns. These effects can be reduced by timely rotation ...

  • Page 302

    Fuel requirements 3.7/4.7l engines (if equipped) all engines (except 5.7l engines) are de- signed to meet all emissions regulations and provide excellent fuel economy and performance when using high quality un- leaded “regular” gasoline having an oc- tane rating of 87. The use of premium gasoline is...

  • Page 303

    Over 40 auto manufacturer’s world wide have issued and endorsed consistent gasoline specifications (the world- wide fuel charter, wwfc) to define fuel properties necessary to deliver enhanced emissions, performance, and durability for your vehicle. The manufacturer recom- mends the use of gasoline t...

  • Page 304

    Mmt in gasoline mmt is a manganese containing metallic additive that is blended into some gasoline to increase octane. Gasoline blended with mmt provides no performance advantage beyond gasoline of the same octane number without mmt. Gasoline blended with mmt reduces spark plug life and reduces emis...

  • Page 305

    • an out-of-tune engine, or certain fuel or ignition malfunctions, can cause the catalytic converter to overheat. If you notice a pungent burning odor or some light smoke, your engine may be out of tune or malfunctioning and may require immediate service. Contact your dealer for service assistance. ...

  • Page 306

    • guard against carbon monoxide with proper mainte- nance. Have the exhaust system inspected every time the vehicle is raised. Have any abnormal conditions repaired promptly. Until repaired, drive with all side windows fully open. • keep the liftgate closed when driving your vehicle to prevent carbo...

  • Page 307

    Caution! Damage to the fuel system or emission control system could result from using an improper fuel cap (gas cap). A poorly fitting cap could let impurities into the fuel system. Also, a poorly fitting after- market cap can cause the mil (malfunction indica- tor light) to illuminate, due to fuel ...

  • Page 308

    Warning! • remove the fuel cap (gas cap) slowly to prevent fuel spray from the filler neck which may cause injury. • the volatility of some gasoline may cause a buildup of pressure in the fuel tank that may increase while you drive. This pressure can result in a spray of gasoline and/or vapors when ...

  • Page 309

    Common towing definitions the following trailer towing related definitions will assist you in understanding the following information: gross vehicle weight rating (gvwr) the gvwr is the total allowable weight of your vehicle. This includes driver, passengers, cargo and tongue weight. The total load ...

  • Page 310

    Warning! It is important that you do not exceed the maximum front or rear gawr. A dangerous driving condition can result if either rating is exceeded. You could lose control of the vehicle and have an accident. Tongue weight (tw) the downward force exerted on the hitch ball by the trailer. In most c...

  • Page 311

    Trailer hitch classification the rear bumper is intended to tow trailers up to 2,000 lbs (907 kg) without added equipment or alterations to the standard equipment. Your vehicle may be factory equipped for safe towing of trailers weighing over 2,000 lbs (907 kg) with the optional trailer tow prep pac...

  • Page 312

    Trailer towing weights (maximum trailer weight ratings) the following chart provides the maximum trailer weight ratings towable for your given drivetrain. Engine/ transmis- sion model gvwr (gross vehicle wt. Rat- ing) gcwr (gross combined wt. Rating) frontal area max. Gtw (gross trailer wt.) max. To...

  • Page 313

    Note 1 – the trailer tongue weight must be considered as part of the combined weight of occupants and cargo, and should never exceed the weight referenced on the tire and loading information placard. Refer to the tire– safety information section in this manual. Trailer and tongue weight always load ...

  • Page 314

    Note: remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options, or dealer-installed options, must be considered as part of the total load on your vehicle. Refer to the tire and loading information plac- ard in the tire safety in...

  • Page 315

    Warning! Improper towing can lead to an injury accident. Follow these guidelines to make your trailer towing as safe as possible: make certain that the load is secured in the trailer and will not shift during travel. When trailering cargo that is not fully secured, dynamic load shifts can occur that...

  • Page 316

    2. Gtw 3. Gawr 4. Tongue weight rating for the trailer hitch utilized (this requirement may limit the ability to always achieve the 10% to 15% range of tongue weight as a percentage of total trailer weight). Towing requirements — tires − do not attempt to tow a trailer while using a compact spare ti...

  • Page 317

    − an electronically actuated trailer brake controller is required when towing a trailer with electronically actuated brakes. When towing a trailer equipped with a hydraulic surge actuated brake system, an electronic brake controller is not required. − trailer brakes are recommended for trailers over...

  • Page 318

    Note: do not cut or splice wiring into the vehicles wiring harness. The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector. Refer to the following illustrations. Towing tips before setting out on a trip, practice turning, stopping and backing ...

  • Page 319

    If using a manual transmission vehicle for trailer towing, all starts must be in first gear to avoid excessive clutch slippage. Towing tips — automatic transmission the “d” range can be selected when towing. However, if frequent shifting occurs while in this range, the ”tow/ haul” mode (if equipped)...

  • Page 320

    Towing tips — cooling system to reduce potential for engine and transmission over- heating, take the following actions: − city driving when stopped for short periods of time, put transmission in neutral and increase engine idle speed. − highway driving reduce speed. − air conditioning turn off tempo...

  • Page 321

    Towing — quadra–trac ii /quadra–drive ii 4wd models caution! Front or rear wheel lifts should not be used. Internal damage to the transmission or transfer case will occur if a front or rear wheel lift is used when recreational towing. Note: the transfer case must be in the n (neutral) position, and ...

  • Page 322

    Hold down n (neutral) “pin” switch (with a pen, etc.) for 4 seconds until the led lamp by the switch starts to blink indicating shift in progress. Lamp will stop blinking (stay on solid) when neutral shift is complete. A “4wd system in neutral” message will display on the evic (electronic vehicle in...

  • Page 323

    5. Start engine. 6. Shift transmission into d (drive). 7. Release brake pedal and ensure that there is no vehicle movement. 8. Shut the engine off. 9. Shift transmission into p (park). 10. Place the ignition key in the off position, and remove key. 11. Apply parking brake. 12. Attach vehicle to the ...

  • Page 324

    Hold down n (neutral) “pin” switch (with a pen, etc.) for 4 seconds until the led lamp by the switch starts to blink indicating shift in progress. Lamp will stop blinking (go out) when shift is complete. The “4wd system in neutral” message will no longer be displayed on the evic (electronic vehicle ...

  • Page 325

    Note: when shifting out of transfer case n (neutral), turning the engine off may be required to avoid gear clash. Warning! You or others could be injured if you leave the vehicle unattended with the transfer case in the n (neutral) position without first fully engaging the parking brake. The transfe...

  • Page 327: Contents

    What to do in emergencies contents 䡵 hazard warning flashers . . . . . . . . . . . . . . . . . 328 䡵 if your engine overheats . . . . . . . . . . . . . . . . . 329 䡵 jacking and tire changing . . . . . . . . . . . . . . . . 330 ▫ jack location . . . . . . . . . . . . . . . . . . . . . . . . 330 ▫ sp...

  • Page 328

    Hazard warning flashers your vehicle’s hazard warning flasher is an emergency warning system. When you activate it, all front and rear directional signals will flash intermittently. Use it when your vehicle is disabled on or near the road. It warns other drivers to steer clear of you and your vehicl...

  • Page 329

    If your engine overheats in any of the following situations, you can reduce the potential for overheating by taking the appropriate ac- tion. • on the highways — slow down. • in city traffic — while stopped, put transmission in n (neutral), but do not increase engine idle speed. Note: there are step...

  • Page 330

    Jacking and tire changing warning! • getting under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never get any part of your body under a vehicle that is on a jack. If you need to get under a raised vehicle, take it to a service center wh...

  • Page 331

    Spare tire stowage the spare tire is stowed under the rear of the vehicle by means of a cable winch mechanism. To remove or stow the spare, use the jack handle to rotate the “spare tire drive” nut. The nut is located under a plastic cover at the center-rear of the cargo floor area, just inside the l...

  • Page 332

    Spare tire removal fit the jack handle extension over the drive nut. Use the lug wrench to rotate the nut counter clockwise until the spare is on the ground with enough slack in the cable to allow to pull the tire out from under the vehicle. Caution! The winch mechanism is designed for use with the ...

  • Page 333

    For example, if changing the right front tire, block the left rear wheel. • passengers should not remain in the vehicle when the vehicle is being jacked. Jacking instructions 1. Remove the spare tire, jack, and tools from storage. 2. Loosen (but do not remove) the wheel lug nuts by turning them to t...

  • Page 334

    4. Locate the jack as shown. For the front axle, place it under the front lower control arm as shown. For the rear axle, place it under the axle near the wheel to be changed. Ensure the jack is closest to the inside of the wheel when jacking on the rear axle. Do not raise the vehicle until you are s...

  • Page 335

    Warning! Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. 6. Remove the lug nuts and wheel. 7. Position the spare wheel/tire on the vehicle and install the lug nuts with ...

  • Page 336

    Note: tire should be stowed with the “beauty” side up. Storing the tire upside down may result in scratching or damage to the wheel face. Continue winching up the tire until you hear the winch “ratchet” three times. Double check to ensure the tire is snug against the underbody of the vehicle. Damage...

  • Page 337

    5. Connect the other cable, first to the negative terminal of the booster battery and then connect the other end to a non-paint metal surface on the engine of the vehicle with the discharged battery. Make sure you have a good contact on the engine. 6. Start the engine in the vehicle which has the bo...

  • Page 338

    • be sure your vehicle is not touching the jump start vehicle. • observe all battery warnings in section 7 of this manual, while jump starting your vehicle. Warning! Do not attempt to push or tow your vehicle to get it started. Unburned fuel could enter the catalytic converter and, once the engine h...

  • Page 339

    Warning! Stand clear of vehicles when pulling with tow hooks. Tow straps and chains may break, causing serious injury. Towing a disabled vehicle 2wd models only provided the transmission is operable, tow only in n (neutral) at speeds not exceeding 30 mph (48 km/h), for distances of not more than 15 ...

  • Page 341: Maintaining Your Vehicle

    Maintaining your vehicle contents 䡵 3.7l engine . . . . . . . . . . . . . . . . . . . . . . . . . . . 344 䡵 4.7l engine . . . . . . . . . . . . . . . . . . . . . . . . . . . 345 䡵 5.7l engine . . . . . . . . . . . . . . . . . . . . . . . . . . . 346 䡵 onboard diagnostic system — obd ii . . . . . . ....

  • Page 342

    ▫ air conditioner maintenance . . . . . . . . . . . . . 359 ▫ power steering fluid check . . . . . . . . . . . . . . 360 ▫ body lubrication . . . . . . . . . . . . . . . . . . . . . 362 ▫ windshield wiper blades . . . . . . . . . . . . . . . . 362 ▫ windshield washers — front and rear . . . . . 362 ...

  • Page 343

    ▫ rear tail, stop, turn signal, and back-up lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 390 ▫ center high mounted stop light (chmsl) . . . 391 䡵 fluid capacities . . . . . . . . . . . . . . . . . . . . . . . . 392 䡵 fluids, lubricants, and genuine parts . . . . . . . . 393 ▫ eng...

  • Page 344

    3.7l engine 344 maintaining your vehicle.

  • Page 345

    4.7l engine maintaining your vehicle 345 7.

  • Page 346

    5.7l engine 346 maintaining your vehicle.

  • Page 347

    Onboard diagnostic system — obd ii your vehicle is equipped with a sophisticated onboard diagnostic system called obd ii. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide ex...

  • Page 348

    Cap until a ⬙clicking⬙ sound is heard. This is an indication that the gas cap is properly tightened. Press the odometer reset button to turn the message off. If the problem persists, the message will appear the next time the vehicle is started. This might indicate a damaged cap. If the problem is de...

  • Page 349

    4. As soon as you turn your key to the on position, you will see your mil symbol come on as part of a normal bulb check. 5. Approximately 15 seconds later, one of two things will happen: a. The mil will flash for about 10 seconds and then return to being fully illuminated until you turn off the igni...

  • Page 350

    Dealer service your dealer has the qualified service personnel, special tools and equipment to perform all service operations in an expert manner. Service manuals are available which include detailed service information for your vehicle. Refer to these manuals before attempting any procedure yoursel...

  • Page 351

    Could adversely affect the engine or vehicle performance. These items should be inspected if a malfunction is observed or suspected. Engine oil checking oil level to assure proper engine lubrication, the engine oil must be maintained at the correct level. Check the oil level at regular intervals, su...

  • Page 352

    • more than 50% of your driving is at sustained high speeds during hot weather, above 90°f (32°c) • trailer towing • taxi, police, or delivery service (commercial service) • off road or desert operation • if equipped for and operating with e-85 (ethanol) fuel if any of these apply to you, then chang...

  • Page 353

    American petroleum institute (api) engine oil identification symbol this symbol means that the oil has been certified by the american petroleum institute (api). The manufacturer only recommends api certified engine oils that meet the requirements of daimlerchrysler material stan- dard ms-6395. Use m...

  • Page 354

    Materials added to engine oils the manufacturer strongly recommends against the ad- dition of any additives (other than leak detection dyes) to engine oil. Engine oil is an engineered product and it’s performance may be impaired by supplemental addi- tives. Disposing of used engine oil care should b...

  • Page 355

    Belts should be inspected for evidence of cuts, cracks, glazing, or frayed cords and replaced if there is indication of damage which could result in belt failure. Low gen- erator belt tension can cause battery failure. Also, check belt routing to make sure there is no inter- ference between the belt...

  • Page 356

    Caution! Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition. In the event of engine malfunction, particularly involv- ing engine misfire or other apparent loss of perfor- mance, have your vehicle serviced promptly. Contin- ued operation of your veh...

  • Page 357

    To minimize the possibility of catalytic converter dam- age: • do not shut off the engine or interrupt the ignition when the transmission is in gear and the vehicle is in motion. • do not try to start the engine by pushing or towing the vehicle. • do not idle the engine with any spark plug wires dis...

  • Page 358

    Air cleaner filter under normal driving conditions, replace the air filter at the intervals shown on “maintenance schedule a.” if, however, you drive the vehicle frequently under dusty or severe conditions, the filter element should be inspected periodically and replaced if necessary at the interval...

  • Page 359

    To determine the battery charge, check the battery test indicator (if equipped) on top of the battery. Refer to the illustration. Caution! It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negat...

  • Page 360

    Warning! • use only refrigerants and compressor lubricants approved by the manufacturer for your air condi- tioning system. Some unapproved refrigerants are flammable and can explode, injuring you. Other unapproved refrigerants or lubricants can cause the system to fail, requiring costly repairs. Re...

  • Page 361

    Caution! Do not use automatic transmission fluid (atf) or other types of power steering fluids when servicing the power steering system of this vehicle. Damage to the power steering system can result from the use of the wrong power steering fluid. Checking the power steering fluid level at a defined...

  • Page 362

    Body lubrication locks and all body pivot points, including such items as seat tracks, doors, tailgate and hood hinges, should be lubricated periodically to assure quiet, easy operation and to protect against rust and wear. Prior to the appli- cation of any lubricant, the parts concerned should be w...

  • Page 363

    The fluid reservoir for the windshield washers and the rear window washer is shared. It is located in the front of the engine compartment (on the driver side), and should be checked for fluid level at regular intervals. Fill the reservoir with windshield washer solvent (not antifreeze/coolant) and o...

  • Page 364

    Cooling system warning! You or others can be badly burned by hot antifreeze/ coolant or steam from your radiator. If you see or hear steam coming from under the hood, don’t open the hood until the radiator has had time to cool. Never try to open a cooling system pressure cap when the radiator or coo...

  • Page 365

    Cooling system — drain, flush, and refill at the intervals shown in the appropriate “maintenance schedule,” the system should be drained, flushed, and refilled. If the solution is dirty and contains a considerable amount of sediment, clean and flush with reliable cooling system cleaner. Follow with ...

  • Page 366

    Adding engine coolant your vehicle has been built with an improved antifreeze/ coolant that allows extended maintenance intervals. This antifreeze/coolant can be used up to 5 years or 100,000 miles before replacement. To prevent reducing this ex- tended maintenance period, it is important that you u...

  • Page 367

    The cap should be inspected and cleaned if there is any accumulation of foreign material on the sealing surfaces. Warning! The warning words do not open hot on the cooling system pressure cap are a safety precaution. Never add antifreeze/coolant when the engine is overheated. Do not loosen or remove...

  • Page 368

    When additional antifreeze/coolant is needed to main- tain the proper level, it should be added to the coolant bottle. Do not overfill. Points to remember note: when the vehicle is stopped after a few miles (kilometers) of operation, you may observe vapor coming from the front of the engine compartm...

  • Page 369

    Only the correct type thermostat. Other designs may result in unsatisfactory cooling performance, poor gas mileage, and increased emissions. Hoses and vacuum/vapor harnesses inspect surfaces of hoses and nylon tubing for evidence of heat and mechanical damage. Hard or soft spots, brittle rubber, cra...

  • Page 370

    Brake and power steering system hoses when servicing the vehicle for scheduled maintenance, inspect surface of hoses for evidence of heat and me- chanical damage. Hard and brittle rubber, cracking, tears, cuts, abrasion, and excessive swelling suggest deteriora- tion of the rubber. Particular attent...

  • Page 371

    Be sure to clean the top of the master cylinder area before removing the cap. If necessary, add fluid to bring the fluid level up to the requirements described on the brake fluid reservoir. With disc brakes, fluid level can be expected to fall as the brake pads wear. However, low fluid level may be ...

  • Page 372

    Caution! Using a transmission fluid other than the manufac- turer’s recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder. Using a transmission fluid other than the manufacturer’s recommended fluid will result in more frequent fluid and filter change...

  • Page 373

    6. Remove the dipstick again and note the fluid level on both sides. The fluid level should be between the “hot” (upper) reference holes on the dipstick at normal operat- ing temperature. The fluid level is only valid if there is a solid coating of oil is seen on both sides of the dipstick. If the f...

  • Page 374

    Special additives the manufacturer recommends against the addition of any additives to the transmission. Exception to this policy is the use of special dyes to aid in detecting fluid leaks. Transfer case fluid level check inspect the transfer case for fluid leaks. If a fluid leak is found, the trans...

  • Page 375

    Front/rear axle fluid front axle fluid level check lubricant should be to the bottom of the oil fill hole. Rear axle fluid level check lubricant should be 1/2” (1 cm) below the oil fill hole. Adding fluid add lubricant only at the fill hole and only to the level specified above. Selection of lubrica...

  • Page 376

    Caution! Under frequent heavy-duty driving conditions, change all lubricants and lubricate body compo- nents, all driveline joints and steering linkage more often than in normal service to prevent excessive wear. Appearance care and protection from corrosion protection of body and paint from corrosi...

  • Page 377

    • if insects, tar, or other similar deposits have accumu- lated on your vehicle, use mopar 威 super kleen bug and tar remover to remove. • use mopar威 cleaner wax to remove road film, stains, and to protect your paint finish. Take care never to scratch the paint. • avoid using abrasive compounds and p...

  • Page 378

    • aluminum wheels should be cleaned regularly with a mild soap and water to prevent corrosion. To remove heavy soil, use mopar 威 wheel cleaner or select a nonabrasive, non-acidic cleaner. Do not use scouring pads, steel wool, a bristle brush or metal polishes. Only mopar 威 cleaners are recommended. ...

  • Page 379

    Do not use polishes, oils, cleaning fluids, solvents, deter- gents, or ammonia based cleaners to clean your leather upholstery. Application of a leather conditioner is not required to maintain the original condition. Warning! Do not use volatile solvents for cleaning purposes. Many are potentially f...

  • Page 380

    Seat belt maintenance do not bleach, dye or clean the belts with chemical solvents or abrasive cleaners. This will weaken the fabric. Sun damage will also weaken the fabric. If the belts need cleaning, use mopar 威 total clean, a mild soap solution, or lukewarm water. Do not remove the belts from the...

  • Page 381

    Cavity fuse/color description 1 30 amp green audio amp (b+) 2 15 amp blue sunroof (b+) 3 10 amp red htd mirror (ebl) 4 20 amp yellow rr pwr out (b+) 5 10 amp red rr hvac (r/o) 6 10 amp red ocm (b+) 7 20 amp yellow door locks (b+) 8 15 amp blue steer col lock (b+) 9 20 amp yellow pwr outlet (b+) 10 1...

  • Page 382

    Underhood fuses (power distribution center) cavity fuse/color description 1 40 amp green hvac blower 2 30 amp pink power outlets 3 30 amp pink rr wiper/ign r/o cavity fuse/color description 4 30 amp pink abs pump 5 50 amp red cabin htr 1 (diesel only) 6 50 amp red asd 7 30 amp pink rr hvac (xk) 8 40...

  • Page 383

    Cavity fuse/color description 19 20 amp yellow ign sw 20 20 amp yellow pcm batt (gasoline only) 21 30 amp pink abs valves 22 spare 23 20 amp yellow fdcm 24 20 amp yellow fuel pump 25 20 amp yellow fdcm/e-diff. 26 15 amp blue hyd/pcm (diesel only) 27 15 amp blue brake/stop lamps 28 25 amp natu- ral n...

  • Page 384

    Underhood fuses (integrated power module) cavity fuse/color description 1 micro relay wiper on/off rly 2 micro relay wiper hi/lo rly 3 micro relay horn rly cavity fuse/color description 4 micro relay rear fog rly (bux only) 5 micro relay lt t-tow stop/turn rly 6 micro relay rt t-tow stop/turn rly 7 ...

  • Page 385

    Cavity fuse/color description 20 20 amp yellow fcm batt #3 21 20 amp yellow rt t-tow stop/turn 22 30 amp pink fdcm mod 23 50 amp red rad fan 24 mini relay rad fan lo rly 25 micro relay ft fog lamps rly 26 micro relay adjustable pedal rly 27 15 amp blue iod #1 28 20 amp yellow iod #2 (audio) 29 10 am...

  • Page 386

    Replacement bulbs interior lights bulb type glove box light . . . . . . . . . . . . . . . . . . . . . . . . . 194 grab handle light . . . . . . . . . . . . . . . . L002825w5w overhead console reading lights . . . . . . . . . . Vt4976 rear cargo light . . . . . . . . . . . . . . . . . . . . . . . 214...

  • Page 387

    Bulb replacement head light 1. Open the hood. 2. Remove the headlamp cover. 3. Turn the low or high beam bulb 1/4 turn counter clockwise to remove from housing. 4. Disconnect the electrical connector and replace the bulb. Maintaining your vehicle 387 7.

  • Page 388

    Caution! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol. Front turn signal 1. Open the hood. 2. Remove the headlamp cover. 3. Turn the turn signal bulb 1/4 turn co...

  • Page 389

    4. Disconnect the electrical connector and replace the bulb. Caution! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol. Front fog light 1. Reach behind the front fas...

  • Page 390

    Caution! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol. Rear tail, stop, turn signal, and back-up lights 1. Raise the liftgate. 2. Remove the two torx fasteners. ...

  • Page 391

    4. Pull the bulb to remove it from the socket. 5. Replace the bulb, reinstall the socket, and reattach the light assembly. Center high mounted stop light (chmsl) 1. Remove the two screws securing the chmsl. 2. Twist the bulb socket to remove from the chmsl housing. 3. Pull the bulb out of the socket...

  • Page 392

    Fluid capacities u.S. Metric fuel (approximate) 20.6 gallons 78 liters engine oil with filter 3.7 liter engine (5w-30, api certified) 5 qts 4.7 liters 4.7 liter engine (5w-30, api certified) 6 qts 5.7 liters 5.7 liter engine (5w-20, api certified) 7 qts 6.6 liters cooling system * 3.7 liter engine (...

  • Page 393

    Fluids, lubricants, and genuine parts engine component fluid, lubricant, or genuine part engine coolant mopar 威 antifreeze/coolant 5 year/100,000 mile formula hoat (hybrid or- ganic additive technology) engine oil (3.7l/4.7l engines) use api certified sae 5w-30 engine oil, meeting the requirements o...

  • Page 394

    Chassis component fluid, lubricant, or genuine part automatic transmission mopar 威 atf+4 automatic transmission fluid transfer case (3.7l engines) mopar 威 atf+4 automatic transmission fluid transfer case (4.7l/5.7l engines) mopar 威 nv 247 transfer case lubricant axle differential (front-rear) mopar ...

  • Page 395: Maintenance Schedules

    Maintenance schedules contents 䡵 emission control system maintenance . . . . . . . . 396 䡵 maintenance schedules . . . . . . . . . . . . . . . . . . . 396 ▫ schedule “b” . . . . . . . . . . . . . . . . . . . . . . . . 399 ▫ schedule “a” . . . . . . . . . . . . . . . . . . . . . . . . 409 8 m a i n t...

  • Page 396

    Emission control system maintenance the “scheduled” maintenance services, listed in bold type must be done at the times or mileages specified to assure the continued proper functioning of the emission control system. These, and all other maintenance services included in this manual, should be done t...

  • Page 397

    • taxi, police, or delivery service (commercial service) • off-road or desert driving • if equipped for and operated with e-85 (ethanol) fuel. Note: most vehicles are operated under the conditions listed for schedule “b.” note: if any of these apply to you, change your engine oil every 3,000 miles (...

  • Page 398

    • check the windshield washer solvent, add as required. Once a month • check the tire pressure and look for unusual wear or damage. • inspect the battery and clean and tighten the terminals as required. • check the fluid levels of the coolant reservoir, brake master cylinder, and transmission, and a...

  • Page 399

    Schedule “b” follow this schedule if you usually operate your vehicle under one or more of the following conditions. • day or night temperatures are below 32°f (0°c) • stop and go driving • excessive engine idling • driving in dusty conditions • short trips of less than 10 miles (16.2 km) • more tha...

  • Page 400

    Miles 3,000 6,000 9,000 12,000 15,000 (kilometers) (5 000) (10 000) (15 000) (20 000) (25 000) change the engine oil and engine oil filter, if not replaced at 3 months. X x x x x rotate the tires. X x check spare tire for proper pressure and correct stowage. X x inspect the engine air cleaner filter...

  • Page 401

    Miles 18,000 21,000 24,000 27,000 30,000 (kilometers) (30 000) (35 000) (40 000) (45 000) (50 000) change the engine oil and engine oil filter, if not replaced at 3 months. X x x x x rotate the tires. X x x check spare tire for proper pressure and correct stowage. X x x inspect the engine air cleane...

  • Page 402

    Miles 33,000 36,000 39,000 42,000 45,000 (kilometers) (55 000) (60 000) (65 000) (70 000) (75 000) change the engine oil and engine oil filter, if not replaced at 3 months. X x x x x rotate the tires. X x check spare tire for proper pressure and correct stowage. X x inspect the engine air cleaner fi...

  • Page 403

    Miles 48,000 51,000 54,000 57,000 60,000 (kilometers) (80 000) (85 000) (90 000) (95 000) (100 000) change the engine oil and engine oil filter, if not replaced at 3 months. X x x x x rotate the tires. X x x check spare tire for proper pressure and correct stowage. X x x inspect the engine air clean...

  • Page 404

    Miles 63,000 66,000 69,000 72,000 75,000 (kilometers) (105 000) (110 000) (115 000) (120 000) (125 000) change the engine oil and engine oil filter, if not replaced at 3 months. X x x x x rotate the tires. X x check spare tire for proper pressure and correct stowage. X x inspect the engine air clean...

  • Page 405

    Miles 78,000 81,000 84,000 87,000 90,000 (kilometers) (130 000) (135 000) (140 000) (145 000) (150 000) change the engine oil and engine oil filter, if not replaced at 3 months. X x x x x rotate the tires. X x x check spare tire for proper pressure and correct stowage. X x x inspect the engine air c...

  • Page 406

    Miles 93,000 96,000 99,000 102,000 105,000 (kilometers) (155 000) (160 000) (165 000) (170 000) (175 000) change the engine oil and engine oil filter, if not replaced at 3 months. X x x x x rotate the tires. X x check spare tire for proper pressure and correct stowage. X x inspect the engine air cle...

  • Page 407

    Miles 108,000 111,000 114,000 117,000 120,000 (kilometers) (180 000) (185 000) (190 000) (195 000) (200 000) change the engine oil and engine oil filter, if not replaced at 3 months. X x x x x rotate the tires. X x x check spare tire for proper pressure and correct stowage. X x x inspect the engine ...

  • Page 408

    Miles 108,000 111,000 114,000 117,000 120,000 (kilometers) (180 000) (185 000) (190 000) (195 000) (200 000) flush and replace the engine coolant/anti-freeze at 120 months, if not replaced at 102,000 miles (170 000 km). X inspection and service should also be performed anytime a malfunction is obser...

  • Page 409

    Schedule “a” miles 6,000 12,000 18,000 24,000 30,000 (kilometers) (10 000) (20 000) (30 000) (40 000) (50 000) [months] [6] [12] [18] [24] [30] change the engine oil and engine oil filter. X x x x x rotate the tires. X x x x x check spare tire for proper pressure and correct stowage. X x x x x inspe...

  • Page 410

    Miles 36,000 42,000 48,000 54, 000 (kilometers) (60 000) (70 000) (80 000) (90 000) [months] [36] [42] [48] [54] change the engine oil and engine oil filter. X x x x rotate the tires. X x x x check spare tire for proper pressure and correct stowage. X x x x inspect the brake linings. X x 410 schedul...

  • Page 411

    Miles 60,000 66,000 72,000 78,000 (kilometers) (100 000) (110 000) (120 000) (130 000) [months] [60] [66] [72] [78] change the engine oil and engine oil filter. X x x x rotate the tires. X x x x check spare tire for proper pressure and correct stowage. X x x x inspect the engine air cleaner filter, ...

  • Page 412

    Miles 84,000 90,000 96,000 102, 000 (kilometers) (140 000) (150 000) (160 000) (170 000) [months] [84] [90] [96] [102] change the engine oil and engine oil filter. X x x x rotate the tires. X x x x check spare tire for proper pressure and correct stowage. X x x x inspect the engine air cleaner filte...

  • Page 413

    Miles 108,000 114,000 120,000 (kilometers) (180 000) (190 000) (200 000) [months] [108] [114] [120] change the engine oil and engine oil filter. X x x rotate the tires. X x x check spare tire for proper pressure and correct stowage. X x x inspect the engine air cleaner filter, and replace if necessa...

  • Page 414

    * this maintenance is not required if the belt was previously replaced. Warning! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the proper equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a...

  • Page 415: Contents

    If you need consumer assistance contents 䡵 suggestions for obtaining service for your vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 416 ▫ prepare for the appointment . . . . . . . . . . . . 416 ▫ prepare a list . . . . . . . . . . . . . . . . . . . . . . . . 416 ▫ be reasonable...

  • Page 416

    Suggestions for obtaining service for your vehicle prepare for the appointment if you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty, discuss additional charges with the service manager. ...

  • Page 417

    Technicians, special tools, and the latest information to assure your vehicle is fixed correctly and in a timely manner. This is why you should always talk to your dealer’s service manager first. Most matters can be resolved with this process. • if for some reason you are still not satisfied, talk t...

  • Page 418

    Customer assistance for the hearing or speech impaired (tdd/tty) to assist customers who have hearing difficulties, the manufacturer has installed special tdd (telecommuni- cation devices for the deaf) equipment at its customer center. Any hearing or speech impaired customer who has access to a tdd ...

  • Page 419

    Warranty information (u.S. Vehicles only) see the warranty information booklet for the terms and provisions of daimlerchrysler’s warranties applicable to this vehicle. Mopar 姞 parts mopar 威 fluids, lubricants, parts, and accessories are available from your dealer. They will help you keep your vehicl...

  • Page 420

    Publication order forms to order the following manuals, you may use either the website or the phone numbers listed below. Visa, mas- tercard, american express, and discover orders are ac- cepted. If you prefer mailing your payment, please call for an order form. Note: a street address is required wh...

  • Page 421

    Call toll free at: • 1–800–890–4038 (u.S.) • 1–800–387–1143 (canada) or visit us on the world wide web at: • www.Techauthority.Daimlerchrysler.Com • www.Daimlerchrysler.Ca/manuals department of transportation uniform tire quality grades the following describes the tire grading categories estab- lish...

  • Page 422

    Warning! The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics. Temperature grades the temperature grades are a (the highest), b, and c, representing the tire’s resistan...

  • Page 423: Index

    Index 10

  • Page 424

    Abs (anti-lock brake system) . . . . . . . . . . . . 181,269 adding washer fluid . . . . . . . . . . . . . . . . . . . . . 171 adjustable pedals . . . . . . . . . . . . . . . . . . . . . . . 146 air cleaner, engine (engine air cleaner filter) . . . 358 air conditioner maintenance . . . . . . . . . ....

  • Page 425

    Auxiliary electrical outlet (power outlet) . . . . . . 162 auxiliary power outlet . . . . . . . . . . . . . . . . . . . 162 battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 358 emergency starting . . . . . . . . . . . . . . . . . . . . . 336 keyless transmitter replacement (rke)...

  • Page 426

    Caution, exhaust gas . . . . . . . . . . . . . . . . . . . . . 153 cd (compact disc) player . . . . . . . . . . . . . . . 202,216 cellular phone . . . . . . . . . . . . . . . . . . . . . . . . . . 83 center high mounted stop light . . . . . . . . . . . . 391 chains, tire . . . . . . . . . . . . . . ...

  • Page 427

    Daytime running lights . . . . . . . . . . . . . . . . . . . 125 dealer service . . . . . . . . . . . . . . . . . . . . . . . . . . 350 defroster, rear window . . . . . . . . . . . . . . . . . . . 234 defroster, windshield . . . . . . . . . . . . . . . . 70,235,242 diagnostic system, onboard . . . ....

  • Page 428

    Engine air cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . 358 block heater . . . . . . . . . . . . . . . . . . . . . . . . . 253 break-in recommendations . . . . . . . . . . . . . . . . 68 compartment . . . . . . . . . . . . . . . . . . . . . . . . . 345 cooling . . . . . . . . . . . . ...

  • Page 429

    Fluid capacities . . . . . . . . . . . . . . . . . . . . . . . . . 392 fluid leaks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 fluid level checks automatic transmission . . . . . . . . . . . . . . . 371,372 engine oil . . . . . . . . . . . . . . . . . . . . . . . . . . . 351 power s...

  • Page 430

    Tachometer . . . . . . . . . . . . . . . . . . . . . . . . . . 182 gear ranges . . . . . . . . . . . . . . . . . . . . . . . . . . . 255 general information . . . . . . . . . . . . . . . . . . . . 23,300 glass cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . 379 gross axle weight rating ...

  • Page 431

    Integrated power module . . . . . . . . . . . . . . . . . . 384 interior appearance care . . . . . . . . . . . . . . . . . . 378 interior fuses . . . . . . . . . . . . . . . . . . . . . . . . . . 380 interior lighting . . . . . . . . . . . . . . . . . . . . . . . . 120 interior lights . . . . . . . ...

  • Page 432

    Cargo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165 center mounted stop . . . . . . . . . . . . . . . . . . . 391 cruise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185 daytime running . . . . . . . . . . . . . . . . . . . . . . 125 dimmer switch, headlight . . . . ...

  • Page 433

    Turn signal . . . . . . . . . . . . . . . . . . 121,126,388,390 vanity mirror . . . . . . . . . . . . . . . . . . . . . . . . . . 82 voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 187 load floor, cargo . . . . . . . . . . . . . . . . . . . . . . . 169 loading vehicle tires . . . ....

  • Page 434

    Rearview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78 vanity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82 modifications/alterations, vehicle . . . . . . . . . . . . . 8 monitor, tire pressure system . . . . . . . . . . . . . . . 294 mopar parts . . . . . . . . . ....

  • Page 435

    Park assist system, rear . . . . . . . . . . . . . . . . . . 141 parking brake . . . . . . . . . . . . . . . . . . . . . . . . . . 267 passing light . . . . . . . . . . . . . . . . . . . . . . . . . . . 126 pedals, adjustable . . . . . . . . . . . . . . . . . . . . . . . 146 pets . . . . . . . . . ....

  • Page 436

    Rear park assist system . . . . . . . . . . . . . . . . . . . 141 rear seat, folding . . . . . . . . . . . . . . . . . . . . . . . 111 rear window defroster . . . . . . . . . . . . . . . . . . . 234 rear window features . . . . . . . . . . . . . . . . . . . . 170 rear wiper/washer . . . . . . . . . ...

  • Page 437

    Adjustable upper shoulder anchorage . . . . . . . . 36 and pregnant women . . . . . . . . . . . . . . . . . . . 40 child restraint . . . . . . . . . . . . . . . . . . . . . . . 58,66 extender . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 front seat . . . . . . . . . . . . . . . . . . ...

  • Page 438

    Snow plow . . . . . . . . . . . . . . . . . . . . . . . . . . . . 325 spare tire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 331 spark plugs . . . . . . . . . . . . . . . . . . . . . . . . . . . . 355 specifications fuel (gasoline) . . . . . . . . . . . . . . . . . . . . . . . . 302 oi...

  • Page 439

    Tire identification number (tin) . . . . . . . . . . . . . 282 tire markings . . . . . . . . . . . . . . . . . . . . . . . . . . 279 tire safety information . . . . . . . . . . . . . . . . . . . . 279 tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70,287,421 air pressure . . . . . . ....

  • Page 440

    Cooling system tips . . . . . . . . . . . . . . . . . . . . 320 hitches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 311 minimum requirements . . . . . . . . . . . . . . . . . 314 trailer and tongue weight . . . . . . . . . . . . . . . . 313 wiring . . . . . . . . . . . . . . . . . . . ...

  • Page 441

    Washer, adding fluid . . . . . . . . . . . . . . . . . . . . . 171 washers, windshield . . . . . . . . . . . . . . . . . . 126,362 washing vehicle . . . . . . . . . . . . . . . . . . . . . . . . . 376 waxing and polishing . . . . . . . . . . . . . . . . . . . . . 376 wheel alignment and balance . . ...

  • Page 442

    442 index.

  • Page 443: Notes

    Notes.

  • Page 444: Notes

    Notes.

  • Page 445: Notes

    Notes.

  • Page 446: Notes

    Notes.

  • Page 447: Notes

    Notes.

  • Page 448: Notes

    Notes.