1. DL manuals
  2. Jeep
  3. Automobile
  4. 2006 Liberty
  5. Owner's Manual

Jeep 2006 Liberty Owner's Manual

Summary of 2006 Liberty

  • Page 1

    Table of contents section page 1 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 things to know before starting your vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 3 understanding the fe...

  • Page 3: Introduction

    Introduction contents 䡵 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 ▫ roll over warning . . . . . . . . . . . . . . . . . . . . . 4 䡵 how to use this manual . . . . . . . . . . . . . . . . . . 6 䡵 warnings and cautions . . . . . . . . . . . . . . . . . . . 6 䡵 vehicle identi...

  • Page 4

    Introduction thank you for selecting a jeep 威 liberty and welcome to our worldwide family. This is a specialized utility vehicle designed for both on-road and off-road use. It can go places and perform tasks for which conventional two-wheel drive vehicles were not intended. However, on-road ride and...

  • Page 5

    Do not attempt sharp turns or abrupt maneuvers or other unsafe driving actions that can cause loss of vehicle control. Failure to operate this vehicle safely may result in an accident, roll over of the vehicle, and severe or fatal injury. Drive carefully. Failure to use driver and passenger seat bel...

  • Page 6

    Note: after you read the manual, it should be stored in the vehicle for convenient reference and remain with the vehicle when sold so that the new owner will be aware of all safety warnings. When it comes to service, remember that the manufac- turer knows your vehicle best, has the factory-trained t...

  • Page 7

    Vehicle identification number the vehicle identification number (vin) is located on a stamped plate on the bottom of the left front a-pillar, visible from outside of the vehicle through the wind- shield. This number also appears on the automobile information disclosure label affixed to a window on y...

  • Page 8

    Vehicle modifications / alterations warning! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death. 8 introduction.

  • Page 9: Contents

    Things to know before starting your vehicle contents 䡵 a word about your keys . . . . . . . . . . . . . . . . . .12 ▫ ignition key . . . . . . . . . . . . . . . . . . . . . . . . . .12 ▫ key-in-ignition reminder . . . . . . . . . . . . . . . .14 䡵 sentry key immobilizer system . . . . . . . . . . . ...

  • Page 10

    ▫ to unlock the doors . . . . . . . . . . . . . . . . . . .23 ▫ to lock the doors . . . . . . . . . . . . . . . . . . . . .23 ▫ to unlatch the swing gate flip-up window . .24 ▫ panic alarm . . . . . . . . . . . . . . . . . . . . . . . . . .25 ▫ to use the panic alarm . . . . . . . . . . . . . . . . ...

  • Page 11

    ▫ seat belt extender . . . . . . . . . . . . . . . . . . . . . .46 ▫ driver and front passenger supplemental restraint systems (srs) — airbags . . . . . . . . . .47 ▫ child restraint . . . . . . . . . . . . . . . . . . . . . . . .61 䡵 engine break-in recommendations . . . . . . . . . . .71 䡵 safety ...

  • Page 12

    A word about your keys the keys for your new vehicle are enclosed in a plastic bag with the key code number on it. If you received your keys without the bag, ask your dealer to give you the number. The key code can also be obtained by the dealer from your vehicle invoice. Ignition key insert the key...

  • Page 13

    Warning! Leaving children in a vehicle unattended is danger- ous for a number of reasons. A child or others could be injured. Children should be warned not to touch the parking brake, brake pedal, or the gear selector lever. Do not leave the keys in the ignition. A child could operate power windows,...

  • Page 14

    Key-in-ignition reminder if you open the driver’s door and the key is fully inserted in the ignition switch, a chime will sound to remind you to remove the key. Sentry key immobilizer system the sentry key immobilizer system (skim) prevents unauthorized operation of the vehicle by disabling the engi...

  • Page 15

    Note: • the sentry key immobilizer system is not compatible with remote starting systems. Use of these systems may result in vehicle starting problems and loss of security protection. • mobil speedpass™, additional sentry keys, or any other transponder equipped components on the same keychain will n...

  • Page 16

    Consists of programming a blank key to the vehicle electronics. A blank key is one which has never been programmed. Note: when having the sentry key system serviced, bring all vehicle keys to the dealer. Customer key programming you can program new keys to the system if you have two valid keys by do...

  • Page 17

    2. This device must accept any interference that may be received, including interference that may cause undes- ired operation. Steering wheel lock — if equipped your vehicle may be equipped with a passive steering wheel lock (manual transmission only). This lock pre- vents steering the vehicle witho...

  • Page 18

    Doors and door locks the vacuum fluorescent (vf) display located in the odometer area displays the word “door” as an indication of a door ajar or door not completely closed. When the vehicle is not moving and the door is ajar or not completely closed, the vf display will show the word “door” and the...

  • Page 19

    Chime for each complete display cycle (three cycles total). After this, the display will continue to cycle only (no chimes). If the trip/reset button is pressed while the vf warnings are being displayed, the vf display will revert back to only displaying the odometer/trip odometer mileage. Manual do...

  • Page 20

    Warning! • for personal security, and safety in the event of an accident, lock the vehicle doors as you drive as well as when you park and leave the vehicle. • when leaving the vehicle always remove the key from the ignition lock, and lock your vehicle. Do not leave children unattended in the vehicl...

  • Page 21

    If you press the door lock switch while the keys are in the ignition switch, and the driver’s door is open, the doors will not lock. The rear doors cannot be opened from inside the vehicle until you pull up the lock plungers. Automatic door locks — if equipped the doors will lock automatically if: 1...

  • Page 22

    Remote keyless entry this system allows you to lock or unlock the doors, open the swing gate flip-up window, or activate the panic alarm from distances of 23–50 feet (7–15 meters) using a transmitter. You don’t have to point the transmitter at the vehicle to activate the system. Each vehicle comes w...

  • Page 23

    To unlock the doors press and release the “unlock” button once to unlock the driver’s door. Press the button again within 5 seconds to unlock all the doors. If your vehicle is equipped with illuminated entry, the interior lights also come on and remain on for about 30 seconds, when you unlock the do...

  • Page 24

    Note: the horn chirp can be enabled or disabled (within 23–50 feet (7–15 meters) of the vehicle) by the following procedure: 1. Press and hold the ⬙lock⬙ button on the transmitter. 2. Continue to hold the ⬙lock⬙ button, wait at least 4 but no longer than 10 seconds, then press the ⬙panic⬙ button. 3....

  • Page 25

    Panic alarm the panic mode flashes the park lights, and sounds the horn for about 3 minutes or until the alarm is turned off. To use the panic alarm press and hold the panic button for at least 1 second to activate the panic alarm. Press and hold the panic button a second time to deactivate the alar...

  • Page 26

    2. Enter program mode: turn the ignition to the on position, and using a currently programmed transmitter; press and hold the ⬙unlock⬙ button on the transmitter. Continue to hold the “unlock” button, wait at least 4 but no longer than 10 seconds, then press and hold the panic button for at least 1 s...

  • Page 27

    Transmitter battery service the recommended replacement battery is the panasonic cr2032 or equivalent. 1. Pry the transmitter halves apart with a dime or similar object. Make sure not to damage the rubber gasket material during removal. 2. Remove and replace the batteries. Avoid touching the new bat...

  • Page 28

    Note: the “panic” and “security” alarms are quite different. Please take a moment to activate the “panic” and the “security” modes to hear the differences in the horn. In case one should go off in the future, you will need to know which mode has been activated in order to deactivate it. To set the a...

  • Page 29

    Press the “unlock” button on the remote keyless entry transmitter to disarm the system. You may also acciden- tally disarm the system by unlocking the driver’s door with the key and then locking it. The door will be locked but the security alarm will not arm. Rear swing gate the swing gate can be un...

  • Page 30

    Warning! To avoid injury stand back when opening. Glass will automatically rise. The vacuum fluorescent (vf) display located in the odometer area displays the words “gate” and/or “glass” as an indication of when the swing gate and/or flip-up window, is not completely closed. When the vehicle is not ...

  • Page 31

    If any other active warnings including “door” or “lo- wash” are present, they will be shown in the vf display and will also continue to cycle. If the vehicle is moving, two single chimes will occur if the rear glass is open or three single chimes will occur if the rear swing gate is open (one chime ...

  • Page 32

    Warning! Driving with the flip-up window open can allow poisonous exhaust gases into your vehicle. You and your passengers could be injured by these fumes. Keep the flip-up window closed when you are operating the vehicle. Note: the rear swing gate will lock while the rear wiper is operating. The ga...

  • Page 33

    The window lock switch located next to the window switches allows you to disable the rear passenger win- dow switches that are located on the back of the center floor console. Auto down feature — if equipped the driver’s and passenger’s front window switches have an auto down feature. Press the wind...

  • Page 34

    Rear passenger window switches the rear passenger window switches are located on the back of the center floor console. Wind buffeting wind buffeting can be described as the perception of pressure on the ears or a helicopter type sound in the ears. Your vehicle may exhibit wind buffeting with the win...

  • Page 35

    Note: the front airbags have a multi stage inflator design. This allows the airbag to have different rates of inflation that are based on collision severity. Please pay close attention to the information in this section. It tells you how to use your restraint system properly to keep you and your pas...

  • Page 36

    Lap/shoulder belts all the seats in your vehicle are equipped with lap/ shoulder belts. The belt webbing retractor is designed to lock during very sudden stops or collisions. This feature allows the shoulder part of the belt to move freely with you under normal conditions. But in a collision, the be...

  • Page 37

    Lap/shoulder belt operating instructions 1. Enter the vehicle and close the door. Sit back and adjust the seat. 2. The seat belt latch plate is above the back of your seat. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to make the belt go aroun...

  • Page 38

    3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” warning! A belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt ...

  • Page 39

    4. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap portion, pull up a bit on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision. No...

  • Page 40

    Warning! A lap belt worn too high can increase the risk of injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdo- men. Always wear the lap part of your seat belt as low as possible and keep it snug. A twisted belt cannot do its job as well. In a col...

  • Page 41

    Rear center lap/shoulder belt retractor lock-out this feature is designed to lock the retractor whenever the 65% rear seat back is not fully latched. This prevents someone from wearing the rear center lap/shoulder belt when the rear seat back is not fully latched. Note: • if the rear center lap/shou...

  • Page 42

    The height of the shoulder belt, slide the height adjuster up. Pull down on the height adjuster to make sure it is locked in place. Warning! Position the shoulder belt height adjusters so that the belt rests across the middle of your shoulder. Failure to adjust the safety belt properly could reduce ...

  • Page 43

    When to use the automatic locking mode anytime a child safety seat is installed in a passenger front or outboard rear seating position (if equipped). Children 12 years old and under should be properly restrained in the rear seat whenever possible. How to use the automatic locking mode 1. Buckle the ...

  • Page 44

    Warning! • after a vehicle collision, the driver and front passenger outboard seat belt system must be checked by a qualified technician to verify that the “automatic locking retractor” feature for child seats is still functioning properly. In addition, all seat belts should be checked for proper fu...

  • Page 45

    Enhanced seat belt use reminder system (beltalert) if the driver’s or front passenger seat belt has not been buckled within 60 seconds of starting the vehicle and if the vehicle speed is greater than 5 mph (8 km/h), the enhanced warning system (beltalert) will alert the driver or front passenger to ...

  • Page 46

    4. Turn the ignition key to the off position. A single chime will sound to signify that you have successfully completed the programming. The enhanced warning system (beltalert) can be reacti- vated by repeating this procedure. Note: although the enhanced warning system (beltalert) has been deactivat...

  • Page 47

    Warning! Using a seat belt extender when not needed can increase the risk of injury in a collision. Only use when the lap belt is not long enough when it is worn low and snug, and in the recommended seating positions. Remove and store the extender when not needed. Driver and front passenger suppleme...

  • Page 48

    The instrument panel, above the glove compartment. The words srs/airbag are embossed on the airbag covers. Note: the front airbags are certified to the federal regulations that allow less forceful deployment. The front airbags have a multi stage inflator design. This may allow the airbag to have dif...

  • Page 49

    Warning! • do not put anything on or around the front airbag covers or attempt to manually open them. You may damage the airbags and you could be injured be- cause the airbags are no longer functional. These protective covers for the airbag cushions are de- signed to open only when the airbags are i...

  • Page 50

    Airbags work, you need the seat belts to keep you in the right position for the airbags to protect you properly. Here are some simple steps you can take to minimize the risk of harm from a deploying airbag. 1. Children 12 years and under should always ride buckled up in a rear seat in an appropriate...

  • Page 51

    Warning! • relying on the airbags alone could lead to more severe injuries in a collision. The airbags work with your seat belt to restrain you properly. In some collisions the airbags won’t deploy at all. Always wear your seat belts even though you have airbags. • being too close to the steering wh...

  • Page 52

    • driver and front passenger seat belt pretensioners • front passenger seat occupant classification system (ocs) − occupant classification module − passenger airbag disabled (pad) indicator light − interconnecting wiring − pressure sensor, bladder assembly, and belt tension sensor how the airbag sys...

  • Page 53

    In any part of the system, it turns on the airbag warning light either momentarily or continuously. A single chime will sound if the light comes on again after initial start up. Warning! Ignoring the airbag warning light in your instru- ment panel could mean you won’t have the airbags to protect you...

  • Page 54

    The crash side of the vehicle. A quantity of nontoxic gas is generated to inflate the window bag. The inflating window bag pushes the outside edge of the headliner out of the way and covers the window. The airbag inflates in about 30 milliseconds (about one quarter of the time it takes to blink your...

  • Page 55

    Grab handle) and airbag warning light (located in the instrument cluster) are illuminated the airbag will be disabled. The orc will not allow front airbag deployment in the event of a collision for occupants classified into the empty or child size categories. The pad indicator light will illuminate ...

  • Page 56

    Should always use the pad indicator light as an indica- tion if the front passenger is properly positioned or not. If the pad indicator light comes on when an adult is in the passenger seat, have the passenger re-position them- selves in the seat until the light goes out. Remember, if the pad indica...

  • Page 57

    Pressure increase due to applied lap belt tension does not cause a small occupant to be classified as a larger occupant. • the bladder mat and pressure sensor are located beneath the seat cushion foam. The pressure sensor sends a signal to the ocm. The front passenger seat assembly contains critical...

  • Page 58

    • do not use prior or future model year seat covers not designated for the specific model being repaired. Al- ways use the correct seat cover specified for the vehicle. • do not replace the seat cover with an aftermarket seat cover. • do not add a secondary seat cover other than those approved by da...

  • Page 59

    However, if you haven’t healed significantly within a few days, or if you have any blistering, see your doctor immediately. As the airbags deflate you may see some smoke-like particles. The particles are a normal by- product of the process that generates the nontoxic gas used for airbag inflation. T...

  • Page 60

    Enhanced accident response system (e.A.R.S.) if the airbags deploy after an impact and the electrical system remains functional, the interior lights will turn on and the power door locks (if equipped) will unlock 5 seconds after airbag deployment. Also, the fuel system will shut off immediately upon...

  • Page 61

    Warning! • you need proper knee impact protection in a collision. Do not mount or locate any aftermarket equipment on or behind the knee bolsters. • it is dangerous to try to repair any part of the airbag system yourself. Be sure to tell anyone who works on your vehicle that it has an airbag system....

  • Page 62

    Warning! In a collision, an unrestrained child, even a tiny baby, can become a missile inside the vehicle. The force required to hold even an infant on your lap can become so great that you could not hold the child, no matter how strong you are. The child and others could be badly injured. Any child...

  • Page 63

    Infant carriers do, so they can be used rearward-facing by children who weigh more than 20 lbs (9 kg) but are less than one year old. • rearward-facing child seats must never be used in the front seat of a vehicle with a front passenger airbag. An airbag deployment could cause severe injury or death...

  • Page 64

    Warning! • improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the manufacturer’s directions ex- actly when installing an infant or child restraint. • a rearward facing infant restraint shou...

  • Page 65

    Belt system will loosen with time, so check the belt occasionally and pull it tight if necessary. If the seat belt has a automatic locking retractor, it will have a distinctive label. Pull the belt from the retractor until there is enough to allow you to pass through the child restraint and slide th...

  • Page 66

    Kits or retro-fit kits. You are urged to take advantage of all the available attachments provided with your child re- straint in any vehicle. Note: when using the latch attaching system to install a child restraint, please ensure that all seat belts not being used for occupant restraints are stowed ...

  • Page 67

    The rear seat lower anchorages are round bars, located at the rear of the seat cushion where it meets the seat back, and are just visible when you lean into the rear seat to install the child restraint. You will easily feel them if you run your finger along the intersection of the seatback and seat ...

  • Page 68

    Many, but not all restraint systems will be equipped with separate straps on each side, with each having a hook or connector for attachment to the lower anchorage and a means of adjusting the tension in the strap. Forward- facing toddler restraints and some rear-facing infant restraints will also be...

  • Page 69

    Installing child restraints using the vehicle seat belt the passenger seat belts are equipped with either cinch- ing latch plates or automatic locking retractors, which are designed to keep the lap portion tight around the child restraint so that it is not necessary to use a locking clip. If the sea...

  • Page 70

    To attach a child restraint tether strap: route the tether strap over the seat back and attach the hook to the tether anchor located on the back of the seat. For the outboard seating positions, route the tether under the head restraint between the head restraint posts. Warning! An incorrectly anchor...

  • Page 71

    • check belt fit periodically. A child’s squirming or slouching can move the belt out of position. • if the shoulder belt contacts the face or neck, move the child closer to the center of the vehicle. Never allow a child to put the shoulder belt under an arm. Transporting pets airbags deploying in t...

  • Page 72

    A new engine may consume some oil during its first few thousand miles (kilometers) of operation. This should be considered as a normal part of the break-in and not interpreted as an indication of difficulty. Safety tips exhaust gas warning! Exhaust gases can injure or kill. They contain carbon monox...

  • Page 73

    Safety checks you should make inside the vehicle seat belts inspect the belt system periodically, checking for cuts, frays and loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Seat belt assemblies must be replaced after an accident if they have been d...

  • Page 74

    Fluid leaks check area under vehicle after overnight parking for fuel, coolant, oil or other fluid leaks. Also, if gasoline fumes are detected, the cause should be located and corrected immediately. 74 things to know before starting your vehicle.

  • Page 75: Contents

    Understanding the features of your vehicle contents 䡵 mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79 ▫ inside day/night mirror . . . . . . . . . . . . . . . . .79 ▫ inside automatic dimming mirror — if equipped . . . . . . . . . . . . . . . . . . . . . . . . . .80 ▫ outside ...

  • Page 76

    ▫ front seat adjustment — recline . . . . . . . . . . 107 ▫ head restraints . . . . . . . . . . . . . . . . . . . . . . 108 ▫ power seat adjuster — if equipped . . . . . . . . 109 ▫ heated seats — if equipped . . . . . . . . . . . . . 110 ▫ 65/35 split folding rear seat . . . . . . . . . . . . . 111...

  • Page 77

    䡵 electronic brake control system . . . . . . . . . . . . 125 ▫ abs (anti-lock brake system) . . . . . . . . . . . . 125 ▫ tcs (traction control system) . . . . . . . . . . . . 126 ▫ bas (brake assist system) . . . . . . . . . . . . . . . 127 ▫ erm (electronic rollover mitigation) . . . . . . . 128 ...

  • Page 78

    ▫ sunroof maintenance . . . . . . . . . . . . . . . . . . . 153 䡵 power outlet . . . . . . . . . . . . . . . . . . . . . . . . . . 153 䡵 cup holders . . . . . . . . . . . . . . . . . . . . . . . . . . 155 ▫ smoker’s package — if equipped . . . . . . . . . . 156 䡵 cargo area features . . . . . . . . ...

  • Page 79

    Mirrors inside day/night mirror the mirror should be adjusted to center on the view through the rear window. A two-point pivot system allows for horizontal and vertical adjustment of the mirror. The mirror should be adjusted while set in the day position (toward windshield). Annoying headlight glare...

  • Page 80

    Inside automatic dimming mirror — if equipped this mirror automatically adjusts for annoying headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light in the button will indicate when the dimming feature is activated. Cauti...

  • Page 81

    Warning! Vehicles and other objects seen in the right side convex mirror will look smaller and farther away than they really are. Relying too much on your right side mirror could cause you to collide with another vehicle or other objects. Use your inside mirror when judging the size or distance of a...

  • Page 82

    Heated remote control mirrors — if equipped these mirrors are heated to melt frost or ice. This feature is activated whenever you turn on the rear window defrost. Illuminated vanity mirrors — if equipped an illuminated vanity mirror is on the sun visor. To use the mirror, rotate the sun visor down a...

  • Page 83

    Hands–free communication (uconnect™) — if equipped uconnect™ is a voice-activated, hands-free, in- vehicle communications system. Uconnect™ allows you to dial a phone number with your cellular phone using simple voice commands (e.G., ⬙call” ѧ “mike” ѧ”work⬙ or ⬙dial” ѧ “248-555-1212⬙). Your cellular...

  • Page 84

    The rearview mirror contains the microphone for the system and the control buttons that will enable you to access the system. The uconnect™ system can be used with any hands- free profile certified bluetooth™ cellular phone. See www.Chrysler.Com/uconnect for supported phones. If your cellular phone ...

  • Page 85

    Uconnect™ system prompts. You will be prompted for a specific command and then guided through the available options. • prior to giving a voice command, one must wait for the voice on beep, which follows the ⬙ready⬙ prompt or another prompt. • for certain operations, compound commands can be used. Fo...

  • Page 86

    Cancel command at any prompt, after the voice on beep, you can say ⬙cancel⬙ and you will be returned to the main menu. However, in a few instances the system will take you back to the previous menu. Pair (link) uconnect™ system to a cellular phone to begin using your uconnect™ system, you must pair ...

  • Page 87

    • the uconnect™ system will then prompt you to begin the cellular phone pairing process on your cellular phone. Before attempting to pair phone, please see your cellular phone’s user manual (bluetooth section) for instructions on how to complete this step. • for identification purposes, you will be ...

  • Page 88

    234-567-890 is nine digits long, which is not a valid phone number - the closest valid phone number has ten digits. • the uconnect™ system will confirm the phone num- ber and then dial. The number will appear in the display of certain radios. Call by saying a name • press the “phone” button to begin...

  • Page 89

    • when prompted, say the name of the new entry. Use of long names helps the voice recognition and is recom- mended. For example, say ⬙robert smith⬙ or ⬙robert⬙ instead of ⬙bob.⬙ • when prompted, enter the number designation (e.G.: ⬙home,⬙ ⬙work,⬙ ⬙mobile,⬙ or ⬙pager⬙). This will allow you to store m...

  • Page 90

    After you are finished editing an entry in the phonebook, you will be given the opportunities to edit another entry in the phonebook, call the number you just edited, or return to the main menu. ⬙phonebook edit⬙ can be used to add another phone number to a name entry that already exists in the phone...

  • Page 91

    Delete all entries in the uconnect™ phonebook • press the ’phone’ button to begin. • after the ⬙ready⬙ prompt and the following beep, say ⬙phonebook erase all.⬙ • the uconnect™ system will ask you to verify that you wish to delete all the entries from the phonebook. • after confirmation, the phonebo...

  • Page 92

    Answer or reject an incoming call - no call currently in progress when you receive a call on your cellular phone, the uconnect™ system will interrupt the vehicle audio system, if on, and will ask if you would like to answer the call. To reject the call, press and hold the ’phone’ button until you he...

  • Page 93

    Conference call when two calls are in progress (one active and one on hold), press and hold the ’phone’ button until you hear a double beep indicating that the two calls have been joined into one conference call. Three-way calling to initiate three-way calling, press the ’voice recogni- tion’ button...

  • Page 94

    Until the vehicle battery condition dictates cessation of the call on the uconnect™ system and transfer of the call to the mobile phone. • after ignition key is switched to off, a call can continue on the uconnect™ system for certain duration, after which the call is automatically transferred from t...

  • Page 95

    If the phone is not reachable and the uconnect™ system is operational, you may reach the emergency number as follows: • press the ’phone’ button to begin. • after the ⬙ready⬙ prompt and the following beep, say ⬙emergency⬙ and the uconnect™ system will instruct the paired cellular phone to call the e...

  • Page 96

    Paging to learn how to page, refer to ⬙working with automated systems. ⬙ paging works properly except for pagers of certain companies which time-out a little too soon to work properly with the uconnect™ system. Voice mail calling to learn how to access your voice mail, refer to ⬙working with automat...

  • Page 97

    Turning confirmation prompts on/off turning confirmation prompts off will stop the system from confirming your choices (e.G. The uconnect™ sys- tem will not repeat a phone number before you dial it). • press the ’phone’ button to begin. • after the ⬙ready⬙ prompt and the following beep, say ⬙setup c...

  • Page 98

    Mute/un-mute (mute off) when you mute the uconnect™ system, you will still be able to hear the conversation coming from the other party, but the other party will not be able to hear you. In order to mute the uconnect™ system: • press the ’voice recognition’ button. • after the ⬙ready⬙ prompt and the...

  • Page 99

    If you would like to connect or disconnect the blue- tooth™ connection between a uconnect™ paired cellular phone and the uconnect™ system, follow the instruction described in your cellular phone user’s manual. List paired cellular phone names • press the ’phone’ button to begin. • after the “ready” ...

  • Page 100

    • the selected phone will be used for the next phone call. If the selected phone is not available, the ucon- nect™ system will return to using the highest priority phone present in or near (approximately with in 30 feet) the vehicle. Delete uconnect™ paired cellular phones • press the ’phone’ button...

  • Page 101

    • low road noise, • smooth road surface, • fully closed windows, • dry weather condition. • even though the system is designed for users speaking in north american english, french, and spanish ac- cents, the system may not always work for some. • when navigating through an automated system, such as,...

  • Page 102

    • dry weather condition. • operation from driver seat. • performance, such as, audio clarity, echo. And loud- ness to a large degree, rely on the phone and network, and not the uconnect™ system. • echo at far end can sometime be reduced by lowering the in-vehicle audio volume. Bluetooth communicatio...

  • Page 103

    Understanding the features of your vehicle 103 3.

  • Page 104

    104 understanding the features of your vehicle.

  • Page 105

    Understanding the features of your vehicle 105 3.

  • Page 106

    North american english primary alternate(s) zero oh add location add new all all of them confirmation prompts confirmations prompts delete a name delete language select language list names list all list paired phones list phones pager beeper phone pairing pairing phonebook phone book return to main ...

  • Page 107

    Using body pressure, move forward and rearward on the seat to be sure the seat adjusters have latched. Warning! • adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be ...

  • Page 108

    Head restraints head restraints can reduce the risk of whiplash injury in the event of impact from the rear. Adjustable head restraints should be adjusted so that the upper edge is as high as practical. The head restraints have a locking button that must be pushed inward to lower the head restraint....

  • Page 109

    Power seat adjuster — if equipped warning! Do not ride with the seatback reclined so that the seat belt is no longer resting against your chest. In a collision you could slide under the seat belt and be seriously or even fatally injured. Use the recliner only when the vehicle is parked. 6–way power ...

  • Page 110

    This seat also has a manual recline lever located just to the rear of the power seat switch. Pull up on the lever to recline the seat. Heated seats — if equipped the heated seat switch is located on the outboard side of the front seats. Pressing this switch to its desired setting (hi or lo) will act...

  • Page 111

    Once the heated seat switch is activated, depressing it a second time will de-activate it. Warning! Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaus- tion or other physical condition must exercise ...

  • Page 112

    Warning! • it is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • be...

  • Page 113

    Note: when lifting up on the release handle, the seatback will release easier if you do not pull forward on the seatback; only lift up on the release handle until the seatback disengages, then fold the seat forward. When the seatback is folded completely forward, the head restraints should be flush ...

  • Page 114

    To open and close the hood to open the hood, two latches must be released. First pull the hood release lever inside your vehicle located under the left side of the instrument panel. Then, reach under the hood and slide the safety latch to the right and lift the hood. To prevent possible damage, do n...

  • Page 115

    Secure both latches. Never drive your vehicle unless the hood is fully closed, with both latches engaged. Warning! If the hood is not fully latched, it could fly up when the vehicle is moving and block your forward vision. Be sure all hood latches are latched fully before driving. Lights interior li...

  • Page 116

    Daytime brightness feature certain components (odometer, radio, etc.) can be illumi- nated at full brightness during the daytime. This can be helpful when driving with your headlights on during the daytime such as in a parade or a funeral procession. To activate this feature, rotate the multi-functi...

  • Page 117

    To change the brightness of the instrument panel lights, rotate the center portion of the multi-function control lever up or down. High beam/low beam select switch pull the multi-function control lever towards you to switch the headlights to high beam. Pull the multi- function control lever a second...

  • Page 118

    Lights-on reminder a chime will sound if the driver’s door is left open, and the headlights or parking lights are left on. Battery saver feature — exterior lights if the park lights, headlights, fog lights, or high beams are left on when the ignition switch is in the off position, the battery saver ...

  • Page 119

    Light bar — if equipped 1. Remove lamp covers by pressing the thumb tab up- wards, and pulling the cover off. Caution! The auxiliary lights mounted on the off road light bar should be illuminated during ⴖoff-road use only. ⴖ having them illuminated on public streets, highways, roads, etc. May be ill...

  • Page 120

    2. With the ignition in the on position, press the button to turn on the light bar (located on the instrument panel to the left of the steering column). Press the button again to turn off the light bar. An indicator light in the instrument cluster will illumi- nate when the light bar has been activa...

  • Page 121

    Windshield wipers and washers the wipers and washers are operated by a switch on the control lever. This control lever is located on the right side of the steering column. For front wiper operation, turn the control lever end cap upward to select the desired wiper speed. Windshield wiper/washer swit...

  • Page 122

    Windshield washers to use the washer, pull the lever toward you and hold while spray is desired. If the lever is pulled while in the delay range, the wiper will operate for two wipe cycles after the lever is released, and then resume the intermit- tent interval previously selected. Note: if vehicle ...

  • Page 123

    Mist feature push down on the wiper lever to activate a single wipe to clear off road mist or spray from a passing vehicle. As long as the lever is held down, the wipers will continue to operate. Caution! In cold weather, always turn off the wiper switch and allow the wipers to return to the park po...

  • Page 124

    Tilt steering column to tilt the column, push down on the lever below the turn signal control and move the wheel up or down, as desired. Pull the lever back towards you and firmly push the lever until it is above the lower surface of the shroud to lock the column in place. Tilt steering column 124 u...

  • Page 125

    Warning! Tilting the steering column while the vehicle is moving is dangerous. Without a stable steering col- umn, you could lose control of the vehicle and have an accident. Adjust the column only while the ve- hicle is stopped. Be sure it is locked before driving. Electronic brake control system y...

  • Page 126

    Warning! Abs (anti-lock brake system) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevail- ing road conditions. Abs cannot prevent accidents, including those resulting from excessive speed in turns, driving on very slippery surf...

  • Page 127

    Bas (brake assist system) the bas is designed to optimize the vehicle’s braking capability during emergency braking maneuvers. The system detects an emergency braking situation by sens- ing the rate and amount of brake application and then applies optimum pressure to the brakes. This can help reduce...

  • Page 128

    Erm (electronic rollover mitigation) this system anticipates the potential for wheel lift by monitoring the driver’s steering wheel input and the speed of the vehicle. When erm determines that the rate of change of the steering wheel angle and vehicles speed are sufficient to potentially cause wheel...

  • Page 129

    Esp (electronic stability program) this system enhances directional control and stability of the vehicle under various driving conditions. Esp cor- rects for over/under steering of the vehicle by applying the brake of the appropriate wheel to assist in counter- acting the over/under steer condition....

  • Page 130

    Warning! Esp (electronic stability program) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions. Esp cannot prevent acci- dents, including those resulting from excessive speed in turns, driving on very slipper...

  • Page 131

    Partial off this mode is entered by momentarily depressing the “esp control switch” (located on top of the steering column). When in “partial off” mode, the tcs portion of esp, except for the “limited slip” feature described in the tcs section, has been disabled and the “esp/tcs indi- cator light” w...

  • Page 132

    Overcome, turn esp back on by momentarily depressing the “esp control switch”. This may be done while the vehicle is in motion. 4wd low range partial off this is the normal operating mode for esp in 4wd low range. Whenever the vehicle is started in 4wd low range or the transfer case (if equipped) is...

  • Page 133

    Note: • ⬙the ⬙esp/tcs indicator light⬙ and the ⬙esp/bas warning lamp ⬙ come on momentarily each time the ignition switch is turned on. • each time the ignition is turned on, the esp system will be on even if it was turned off previously. • the esp control system will make buzzing or clicking sounds ...

  • Page 134

    To set at a desired speed when the vehicle has reached the desired speed, press and release the set button. Release the accelerator and the vehicle will operate at the selected speed. To deactivate a soft tap on the brake pedal, normal braking, or pressing the cancel button will deactivate the speed...

  • Page 135

    To accelerate for passing depress the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed. Note: when driving uphill, at elevations above 2,000 ft. (610 meters), or when the vehicle is heavily loaded (especially when towing) the vehicle may slow be...

  • Page 136

    Pressing the menu button will change the displayed programming features. Pressing the step button will select the available choices. Pressing the c/t (compass/ temperature) button will return the display to the normal compass/temperature display. Note: temperature accuracy can be effected from heat ...

  • Page 137

    Note: the dome/reading lights will remain on until the switch is pressed a second time, so be sure they have been turned off before leaving the vehicle. Electronic vehicle information center the electronic vehicle information center (evic), when the appropriate conditions exist, displays the followi...

  • Page 138

    Customer programmable features press the menu button until one of the display choices following appears: language? When in this display you may select one of five lan- guages for all display nomenclature, including the trip computer functions. Press the step button while in this display to select en...

  • Page 139

    All doors. This can also be programmed using the key fob, refer to “remote keyless entry” earlier in this section. Train remote? Pressing the step button when in this display will select “yes” or “no.” note: any time you perform this procedure, it is necessary to retrain all currently trained key fo...

  • Page 140

    Flash lights with locks? When this feature is selected, the front and rear turn signals will flash when the doors are locked or unlocked using the remote keyless entry transmitter. This feature may be selected with or without the sound horn on lock feature selected. Pressing the step button when in ...

  • Page 141

    Low fuel chime? When this feature is selected a chime will sound when the “low fuel indicator light” is displayed in the instrument panel cluster. Pressing the step button when in this display will select “yes” or “no.” mini-trip computer this feature, located in the overhead console, displays infor...

  • Page 142

    Warning! Even if the display still reads a few degrees above 32°f (0°c), the road surface may be icy, particularly in woods or on bridges. Drive carefully under such conditions to prevent an accident and possible per- sonal injury or property damage. Step button press the step button to cycle throug...

  • Page 143

    Tire psi shows the pressure and location of each tire, except for the spare tire. The tire location will blink when under pressure. Blank screen shows a blank screen. Pressing the c/t button returns to the compass and temperature display. Pressing the step button returns you to the average miles per...

  • Page 144

    Compass variance is the difference between magnetic north and geographic north. In some areas of the country, the difference between magnetic and geographic north is great enough to cause the compass to give false readings. If this occurs, the compass variance must be set according to the compass va...

  • Page 145

    To set the variance: turn the ignition on and set the display to “compass/temperature.” press and hold the reset button five seconds (no more than 10 seconds). The last variance zone number will be displayed. Press the step button to select the new variance zone and press the reset button to resume ...

  • Page 146

    Warning! Before programming homelink to a garage door opener or gate operator, make sure that people and objects are out of the way of the device to prevent potential harm or damage. When programming a garage door opener, it is advised to park outside of the garage. Do not use homelink with any gara...

  • Page 147

    Warning! Vehicle exhaust contains carbon monoxide, a danger- ous gas. Do not run the vehicle’s engine while programming homelink. Exhaust gas can cause se- rious injury or death. Warning! Your motorized door or gate will open and close while you are programming homelink. Do not program homelink if p...

  • Page 148

    2. Simultaneously press and hold both the desired homelink button and the hand-held transmitter button. After a short time, the message training will show on homelink display. Do not release the buttons until the next step has been completed. 3. When the message trained appears on the homelink displ...

  • Page 149

    Steps five through seven below to complete the program- ming of a rolling code equipped device (most commonly a garage door opener). 5. At the garage door opener receiver (motor-head unit) in the garage, locate the ⬙learn⬙ or ⬙smart⬙ button. This can usually be found where the hanging antenna wire i...

  • Page 150

    Garage door opener’s owner’s manual. Finally, repro- gram the hand-held transmitter(s) to homelink using the steps under ⴖprogramming homelinkⴖ. Gate operator/canadian programming canadian radio-frequency laws require transmitter sig- nals to ⬙time-out⬙ (or quit) after several seconds of transmissio...

  • Page 151

    Power sunroof — if equipped the sunroof control is located on the headliner between the sun visors. Press and hold the switch rearward to fully open the sunroof. The sunroof can be stopped at any position between closed and full open. Momentarily pressing the switch rearward will activate the expres...

  • Page 152

    Press and hold the “v” button in the center of the sunroof switch to open the vent. The sunroof can be stopped at any position between closed and full vent. To close the sunroof from the vent position, press and hold the switch forward. Releasing the switch will stop the movement of the sunroof and ...

  • Page 153

    Warning! • in an accident, there is a greater risk of being thrown from a vehicle with an open sunroof. You could also be seriously injured or killed. Always fasten your seat belt properly and make sure all passengers are properly secured too. • do not allow small children to operate the sun- roof. ...

  • Page 154

    There is a rear power outlet located in the right rear cargo area above the storage cargo net/cd changer (if equipped). The rear power outlet is a direct feed from the battery so it receives power whether the ignition is in the on or off position. All accessories connected to this outlet should be r...

  • Page 155

    Caution! Electrical outlet use with engine off • many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.E., cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or ...

  • Page 156

    Smoker’s package — if equipped with the optional smoker’s package, a removable ash tray is inserted into the front cup holder location. The rear passengers have access to a cup holder on each rear door trim panel. Rear cup holders 156 understanding the features of your vehicle.

  • Page 157

    Cargo area features cargo light the cargo area light is activated by opening the swing gate, opening any door, or by rotating the dimmer control on the multi-function control lever to the extreme top position. If all doors are closed and only the swing gate is open, pushing on the cargo light lens s...

  • Page 158

    Warning! In an accident a cargo cover loose in the vehicle could cause injury. It could fly around in a sudden stop and strike someone in the vehicle. Do not store the cargo cover on the cargo floor or in the passenger compartment. Remove the cover from the vehicle when taken from its mounting. Do n...

  • Page 159

    Warning! • cargo tie-down hooks are not safe anchors for a child seat tether strap. In a sudden stop or colli- sion a hook could pull loose and allow the child seat to come loose. A child could be badly injured. Use only the anchors provided for child seat tethers. • the weight and position of cargo...

  • Page 160

    Cargo organizer — if equipped this vehicle may be equipped with a cargo organizer that mounts on the floor behind the rear seat. Items may be placed on the flat surface or stored in the three storage compartments. Warning! • to avoid tipping, lock the shelf securely in all positions. • do not drive ...

  • Page 161

    2. Place the rear corners of the cargo organizer into the supports located on the rear trim panel. Press down on the back of the cargo organizer to lock it into place. Warning! Do not load objects over 30 lbs (13.5 kg) in the upper position. Failure to follow this warning could cause the cargo organ...

  • Page 162

    To open storage compartments 1. Pull up on the center opening of the cargo organizer. 2. Lift up on the storage compartment dividers and lock into place. Cargo organizer removal loosen screw, then lift lever from each mount located on the floor of the rear cargo area, and remove the cargo organizer ...

  • Page 163

    If the swing gate flip-up window is open or the swing gate is open, connection to the rear window wiper is interrupted preventing activation of the rear wiper blade. When the swing gate flip-up window or the swing gate is closed, the rear wiper switch or the ignition switch needs to be turned off, a...

  • Page 164

    The defroster will automatically turn off after about ten minutes. For about five more minutes of operation, push the button again. To prevent excessive battery drain, use the defroster only when the engine is operating. The push button also activates the heated exterior mirrors, if so equipped. Cau...

  • Page 165

    Caution! • to avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity of 150 lbs (68 kg) or 65 lbs (29.5 kg) on renegade models. Always distribute heavy loads as evenly as possible and secure the load appropriately. • long loads which extend over the windshield, ...

  • Page 167: Contents

    Understanding your instrument panel contents 䡵 instrument panel and interior controls . . . . . . . 170 䡵 instrument cluster . . . . . . . . . . . . . . . . . . . . . . 171 ▫ 3.7l engines . . . . . . . . . . . . . . . . . . . . . . . . . 171 ▫ 2.8l diesel engines . . . . . . . . . . . . . . . . . . ...

  • Page 168

    ▫ cd changer control capability — if equipped . . . . . . . . . . . . . . . . . . . . . . . . . 189 䡵 sales code rbq—am/fm stereo radio with 6 - disc cd changer . . . . . . . . . . . . . . . . . . . . 191 ▫ radio operation . . . . . . . . . . . . . . . . . . . . . . 191 ▫ cd player operation . . . ....

  • Page 169

    ▫ tape player . . . . . . . . . . . . . . . . . . . . . . . . . 206 ▫ cd player — single disc in radio . . . . . . . . . 206 ▫ cd player — 6 disc in cargo area . . . . . . . . . 206 䡵 cd/dvd disc maintenance . . . . . . . . . . . . . . . 207 䡵 radio operation and cellular phones . . . . . . . . 207 ...

  • Page 170

    Instrument panel and interior controls 170 understanding your instrument panel.

  • Page 171

    Instrument cluster 3.7l engines understanding your instrument panel 171 4.

  • Page 172

    2.8l diesel engines 172 understanding your instrument panel.

  • Page 173

    Instrument cluster description 1. Tachometer indicates the permissible engine revolutions-per-minute for each gear range. Before reaching the red area, ease up on the accelerator to prevent engine damage. 2. Turn signal indicator light the arrows will flash in unison with the exterior turn signals, ...

  • Page 174

    Inflate them to the proper pressure. Driving on a signifi- cantly under-inflated tire causes the tire to overheat and can lead to tire failure. Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability. Please note that the tpms is n...

  • Page 175

    When the engine is running, the “malfunction indicator light” may flash to alert of serious conditions that could lead to immediate loss of power or severe catalytic converter damage. The vehicle should be serviced as soon as possible if this occurs. (see page 316 for more information.) 9. Anti-lock...

  • Page 176

    Or the battery is low. Also, a chime will sound if the light comes back on. See your authorized dealer immediately. 11. Temperature gage indicates engine coolant temperature. Any read- ing within the normal range indicates that the cooling system is operating satisfactorily. The gage pointer will li...

  • Page 177

    The instrument cluster). For additional information, refer to “overhead console — if equipped” in section 3. (see page 135 for more information.) note: the warnings “locool” and “gascap” will always be displayed in the odometer display. U.S. Federal regulations require that upon transfer of vehicle ...

  • Page 178

    17. Part time indicator light — if equipped this light alerts the driver that the vehicle is in the part time four–wheel drive high range mode, and the front and rear driveshafts are mechanically locked together forcing the front and rear wheels to rotate at the same speed. (see page 234 for more in...

  • Page 179

    Also, the light will come on when the parking brake is applied with the ignition switch in the on position. Note: this light shows only that the parking brake is applied. It does not show the degree of brake application. If the parking brake is off and the light remains on, have the brake system ins...

  • Page 180

    Light doesn’t come on, stays on, or comes on while driving, have the airbag system checked by an autho- rized dealer. 24. O/d (overdrive) off indicator light this light will illuminate when the o/d off button has been selected. The o/d off button is located on the gear shift lever. 25. Seat belt ind...

  • Page 181

    The vehicle is safely and completely stopped and the gear selector is placed in the p (park) position. The light should turn off. If the light remains on with the engine running, your vehicle will usually be drivable, however, see your dealer for service as soon as possible. If the light continues t...

  • Page 182

    30. Electronic stability program (esp) warning light/brake assist system (bas) warning light — if equipped the esp/bas warning light in the instrument cluster comes on when the ignition switch is turned to the “on” position. The light should go out with the engine running. If the esp/ bas warning li...

  • Page 183

    Electronic digital clock the clock and radio each use the display panel built into the radio. A digital readout shows the time in hours and minutes whenever the ignition switch is in the on or acc position and the time button is pressed. When the ignition switch is in the off position, or when the r...

  • Page 184

    Electrical disturbances radio waves may pick up electrical disturbances during transmission. They mainly affect the wave amplitude, and thus remain a part of the am reception. They interfere very little with the frequency variations that carry the fm signal. Am reception am sound is based on wave am...

  • Page 185

    Sales code rbk—am/ fm stereo radio with cd player and cd changer controls note: the radio sales code is located on the lower left side of your radio faceplate. Radio operation power/volume control press the on/vol control to turn the radio on. Turn the volume control clockwise to increase the volume...

  • Page 186

    The radio will continue to tune until you release the button. The frequency will be displayed and continu- ously updated while the button is pressed. To set the radio push-button memory when you are receiving a station that you wish to commit to push-button memory, press the set button. Set 1 will s...

  • Page 187

    Press the audio button a fourth time and fade will be displayed. Press the seek + or seek – to adjust the sound level between the front and rear speakers. Press the audio button again or wait 5 seconds to exit setting tone, balance, and fade. Am/fm selection press the am/fm button to change from am ...

  • Page 188

    Inserting the compact disc caution! This cd player will accept 4 3 ⁄ 4 inch (12 cm) discs only. The use of other sized discs may damage the cd player mechanism. You may either insert or eject a disc with the radio off. If you insert a disc with the ignition on and the radio off, the display will sho...

  • Page 189

    Ff/tune/rw press ff (fast forward) and the cd player will begin to fast forward until ff is released. The rw ( reverse) button works in a similar manner. Random play — rnd/program button 4 press the rnd (button 4) button while the cd is playing to activate random play. This feature plays the tracks ...

  • Page 190

    Disc up/program button 1 press the disc up (button 1) button to play the next available disc. Disc down/program button 5 press the disc down (button 5) button to play the previous disc. Seek button press the seek up or down to select another track on the same disc. A seek symbol will appear on the d...

  • Page 191

    Cd hot will pause the operation. Play can be resumed when the operating temperature is corrected or another mode is selected. An err symbol will appear on the display if the laser is unable to read the disc data for the following reasons: • excessive vibration • disc inserted upside down • damaged d...

  • Page 192

    Note: power to operate the radio is controlled by the ignition switch. It must be in the on or acc position to operate the radio. Mode press the mode button repeatedly to select between am, fm, the cd changer and sirius satellite radio™ (if equipped). The display will show st when a stereo station i...

  • Page 193

    And release that button. If a button is not selected within 5 seconds after pressing the set rnd button, the station will continue to play but will not be locked into push- button memory. You may add a second station to each push-button by repeating the above procedure with this exception: press the...

  • Page 194

    General information this radio complies with part 15 of fcc rules and with rss-210 of industry canada. Operation is subject to the following conditions: 1. This device may not cause harmful interference, 2. This device must accept any interference received, including interference that may cause unde...

  • Page 195

    Show the disc number, the track number, and index time in minutes and seconds. Play will begin at the start of track 1. Load/ ejt — load press the load/ ejt button and the button with the corresponding number where the cd is being loaded. After the radio displays “load” insert the cd into the player...

  • Page 196

    Ff/tune/rw press ff (fast forward) and the cd player will begin to fast forward until ff is released. The rw ( reverse) button works in a similar manner. Random play — set / rnd press the rnd button while the cd is playing to activate random play. This feature plays the tracks on the disc in random ...

  • Page 197

    Program type radio display nostalgia nostalga oldies oldies personality persnlty public public rhythm and blues r & b religious music rel musc religious talk rel talk rock rock soft soft soft rock soft rck soft rhythm and blues soft r&b sports sports talk talk top 40 top 40 weather weather by pressi...

  • Page 198

    Time press the time button to change the display from elapsed cd playing time to time of day. Operating instructions - satellite radio mode (if equipped) refer to the satellite radio section of the owner’s manual. Cd diagnostic indicators when driving over a very rough road, the cd player may skip m...

  • Page 199

    Sales code rb1—am/fm stereo radio with dvd/gps navigation system the navigation system provides maps, turn identifica- tion, selection menus and instructions for selecting a variety of destinations and routes. Refer to your “navi- gation user’s manual” for detailed operating instruc- tions. Note: if...

  • Page 200

    1. Slide the cd changer door all the way to the right. 2. Press the green eject button. 3. Gently remove the magazine by pulling it out of the cd changer. 4. Close the cd changer door by sliding it to the left. Loading discs into the magazine gently pull out a tray from the magazine, and place the d...

  • Page 201

    Installing the cd changer magazine 1. Slide the cd changer door all the way to the right to access the magazine slot. 2. Insert the magazine into the changer slot in the direction of the arrow on the magazine. 3. Slide the changer door to the left to close the changer door. Satellite radio — if equi...

  • Page 202

    Esn/sid access with rbb, rah and rbk radios with the ignition switch in the accessory position and the radio off, press the tape eject or cd eject (depend- ing on the radio type) and time buttons simultaneously for 3 seconds. The first four digits of the twelve-digit esn/sid number will be displayed...

  • Page 203

    • the current channel number will then be displayed until an action occurs. A cd or tape may remain in the radio while in the satellite radio mode. Selecting a channel press and release the seek or tune buttons to search for the next channel. Press the top of the button to search up and the bottom o...

  • Page 204

    Note: pressing the ⬙seek⬙ or ⬙scan⬙ button while performing a music type scan will change the channel by one and stop the search. Pressing a pre-set memory button during a music type scan, will call up the memory channel and stop the search. Pty button ⴖseekⴖ when the desired program is obtained, pr...

  • Page 205

    Remote sound system controls — if equipped the remote sound system controls are located on the rear surface of the steering wheel. Reach behind the wheel to access the switches. The right hand control is a rocker type switch with a push-button in the center and controls the volume and mode of the so...

  • Page 206

    Radio operation pressing the top of the switch will “seek” up for the next listenable station and pressing the bottom of the switch will “seek” down for the next listenable station. The button located in the center of the left hand control will tune to the next preset station that you have pro- gram...

  • Page 207

    If you press the switch up or down twice it plays the second track, three times, it will play the third, etc. The button in the center of the left hand switch will cause the cd changer to play the next available disc in the 6–disc magazine. Cd/dvd disc maintenance to keep the cd/dvd discs in good co...

  • Page 208

    Climate controls the controls for the heating, air conditioning, and venti- lation system in this vehicle consist of a series of rotary knobs, and a push-button. These comfort controls can be set to obtain desired interior conditions. Blower control the rotary knob on the left controls the blower an...

  • Page 209

    Off this position turns off the blower motor and outside air will not pass through any outlets. Recirculate (max a/c) air flows through the outlets located in the instrument panel. Allows for circulation of interior air only which will cool the cabin faster. This setting can be used in very hot weat...

  • Page 210

    Mix air flows through the floor outlets, the outlets at the base of the windshield, and the side window demisters outlets. Defrost air flows through the outlets at the base of the windshield and through the side window demister outlets. Operating tips fast cool down for a fast cool down, turn the bl...

  • Page 211

    Summer operation air conditioned equipped vehicle’s cooling systems must be protected with a high quality engine coolant during summer to provide proper corrosion protection and to raise the boiling point of the coolant for protection against overheating. A 50% concentration is recom- mended. Winter...

  • Page 213: Starting And Operating

    Starting and operating contents 䡵 starting procedures . . . . . . . . . . . . . . . . . . . . . 217 ▫ manual transmission . . . . . . . . . . . . . . . . . . 217 ▫ automatic transmission . . . . . . . . . . . . . . . . 217 ▫ normal starting — gasoline engines . . . . . . . 218 ▫ normal starting — di...

  • Page 214

    ▫ shift positions . . . . . . . . . . . . . . . . . . . . . . . . 240 ▫ shifting procedure . . . . . . . . . . . . . . . . . . . . 241 䡵 trac-lok™ rear axle — if equipped . . . . . . . . . 243 䡵 parking brake . . . . . . . . . . . . . . . . . . . . . . . . . 243 䡵 anti-lock brake system — if equippe...

  • Page 215

    ▫ replacement tires . . . . . . . . . . . . . . . . . . . . . 266 ▫ alignment and balance . . . . . . . . . . . . . . . . . 267 䡵 tire pressure monitor system (tpms) — if equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . 268 ▫ base system . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Page 216

    ▫ towing tips . . . . . . . . . . . . . . . . . . . . . . . . . 292 䡵 recreational towing (behind motorhome, etc.) . . 294 ▫ towing – 2wd models . . . . . . . . . . . . . . . . . 294 ▫ towing — 4wd models . . . . . . . . . . . . . . . . 294 䡵 snow plow . . . . . . . . . . . . . . . . . . . . . . . ....

  • Page 217

    Starting procedures before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. Warning! Do not leave children or animals inside parked vehicles in hot weather. Interior heat build up may cause serious injury or death. Manual transmission apply...

  • Page 218

    Normal starting — gasoline engines normal starting of either a cold or a warm engine is obtained without pumping or depressing the accelerator pedal. Turn the key to the start position and release when the engine starts. If the engine fails to start within 10 seconds, turn the key to the off positio...

  • Page 219

    Caution! To prevent damage to the starter, do not crank the engine for more than 15 seconds at a time. Wait 10 to 15 seconds before trying again. If the engine has been flooded, it may start to run, but not have enough power to continue running when the key is released. If this occurs, continue cran...

  • Page 220

    Operation may result in starter or battery damage. If the engine does not start at once, repeat steps 1 through 4. • cold engine speeds higher than necessary for driving or higher than specified for idling may damage engine components. • before turning off your diesel engine, always allow the engine...

  • Page 221

    Turbocharger ⬙cool down⬙ chart driving conditions load turbocharger temperature idle time (in minutes) before shut down stop & go empty cool less than 1 stop & go medium warm 1 highway speeds medium warm 2 city traffic max. Gcwr warm 3 highway speeds max. Gcwr warm 4 uphill grade max. Gcwr hot 5 die...

  • Page 222

    Should your vehicle run out of fuel, the fuel system must be re-primed in order to start the engine. Factors such as temperature, which affects the viscosity of the fuel, how long the vehicle has been sitting and other factors will influence how quickly the engine starts. Re-priming the diesel fuel ...

  • Page 223

    5. Depress the fuel-water separator knob 20 consecutive times. 6. Turn the ignition to start and crank the engine a maximum of 10 seconds. The engine should start and remain running. Note: if the engine does not start, repeat the cycle as many times as necessary. Engine block heater — if equipped th...

  • Page 224

    Transmission shifting 6-speed manual transmission follow the shift pattern on the gearshift knob. Note: the backup lights will come on when your vehicle is in r (reverse) gear and the ignition is in the on position. Manual shift controls 224 starting and operating.

  • Page 225

    Warning! When parking your vehicle, always leave a manual transmission in first gear and apply the parking brake fully to guard against vehicle movement and possible injury or damage. Never use any gear as a substitute for the parking brake. Caution! To drive as safely as possible and to prolong the...

  • Page 226

    • when “rocking” a stuck vehicle by shifting between a forward gear and reverse, do not spin wheels faster than 15 mph (24 km/h), or drivetrain damage may result. Recommended manual transmission shifting speeds the manufacturer recommends that you use the shift speeds listed in the chart below. Manu...

  • Page 227

    Automatic transmission shifting from d (drive) to p (park) or r (reverse) (or from p or r to d) should be done only after the accelerator pedal is released and the vehicle is stopped. Be sure to keep your foot on the brake when moving the shift lever between these gears. Warning! It is dangerous to ...

  • Page 228

    Gear ranges p (park) supplements the parking brake by locking the transmis- sion. The engine can be started in this range. Never use p (park) while the vehicle is in motion. Apply the parking brake when leaving the vehicle in this range. Always place the gear selector in the p (park) position first,...

  • Page 229

    The following indicators should be used to ensure that you have engaged the transmission shift lever into the p (park) position: • when shifting into p (park), depress the button on the shift lever and firmly move the lever all the way forward until it stops. • look at the shift indicator window on ...

  • Page 230

    Warning! Do not coast in n (neutral) and never turn off the ignition to coast down a hill. These are unsafe prac- tices that limit your response to changing traffic or road conditions. You might lose control of the vehicle. Overdrive (o/d) for most city and highway driving. The transmission contains...

  • Page 231

    Overdrive can be locked out by pressing the o/d off button located on side of the gearshift lever. The o/d off indicator light will illuminate to show that the switch has been activated. When the indicator light is on, overdrive is locked out. Pressing the switch a second time restores the overdrive...

  • Page 232

    Caution! • never press on the accelerator pedal with the engine running, vehicle in gear, and the brakes applied. Always apply the brakes when stopped on a incline. Failure to follow these instructions can cause overheating and damage to the trans- mission. • when “rocking” a stuck vehicle by moving...

  • Page 233

    (48 km/h). To understand the difference in operation, drive the vehicle so that tcc engagement conditions are correct, and then press and release the “o/d off” button once to disengage the tcc. Wait a few seconds, and then press and release the “o/d off” button again to engage the tcc. You will noti...

  • Page 234

    Caution! When “rocking” a stuck vehicle by moving between “first” and r (reverse), do not spin the wheels faster than 15 mph (24 km/h), or drivetrain damage may result. Four-wheel drive operation command-trac 姞 operating information/precautions the command-trac 威 transfer case provides 4 mode positi...

  • Page 235

    Caution! • do not attempt to make a shift while only the front or rear wheels are spinning. The command- trac transfer case is not equipped with a synchro- nizer and therefore the front and rear driveshaft speeds must be equal for the shift to take place. Shifting while only the front or rear wheels...

  • Page 236

    Warning! • because 4-wheel drive provides improved trac- tion, there is a tendency to exceed safe turning and stopping speeds. Do not go faster than road con- ditions permit. • you or others could be injured if you leave the vehicle unattended with the transfer case in the neutral (n) position witho...

  • Page 237

    4l 4-wheel-drive low range - low speed 4 wheel drive. Locks the front and rear driveshafts together. Forces the front and rear wheels to rotate at the same speed. Additional traction and maximum pulling power for loose, slippery road surfaces only. Do not exceed 25 mph (40 km/h). (allows engine star...

  • Page 238

    Note: shifting into or out of 4l is possible with the vehicle completely stopped, however difficulty may oc- cur due to the mating clutch teeth not being properly aligned. Several attempts may be required for clutch teeth alignment and shift completion to occur. The pre- ferred method is with the ve...

  • Page 239

    The part time indicator light, located on the instru- ment cluster, illuminates when the transfer case is shifted to the 4 part time position. The full time indicator light, located on the instru- ment cluster, illuminates when the transfer case is shifted to the 4 full time position. The 4lo mode i...

  • Page 240

    Proper operation of 4-wheel drive vehicles depends on tires of equal size, type, and circumference on each wheel. Any difference will adversely affect shifting and can cause damage to the transfer case. Warning! • because 4-wheel drive provides improved trac- tion, there is a tendency to exceed safe...

  • Page 241

    N neutral - disengages both the front and rear driveshafts from the powertrain. To be used for flat towing behind another vehicle. Refer to “recreational towing” in sec- tion 5 for more information. 4lo part time 4–wheel drive low range - low speed 4–wheel drive. Locks the transfer case inter-axle d...

  • Page 242

    Shifting. This will allow full engagement of the newly selected position. Apply a constant force when shifting the transfer case lever. 4 full time to 4 lo or 4 lo to 4 full time with the vehicle rolling at 2 to 3 mph (3 to 5 km/h), shift an automatic transmission to n (neutral). While the vehicle i...

  • Page 243

    Trac-lok™ rear axle — if equipped the optional trac-lok™ rear axle provides a constant driving force to both rear wheels and reduces wheel spin caused by the loss of traction at one driving wheel. If traction differs between the two rear wheels, the differ- ential automatically proportions the usabl...

  • Page 244

    To release the parking brake, pull up slightly, press the center button, then lower the lever completely. Before leaving the vehicle parked on a hill, you must make sure the parking brake is fully applied and place the gear selector in the p (park) position. Make certain the transfer case is in gear...

  • Page 245

    Be sure the parking brake is fully disengaged before driving. Failure to do so can lead to brake failure. Note: parking brake adjustment and maintenance should be performed by your authorized dealer. Anti-lock brake system — if equipped the anti-lock brake system is designed to aid the driver in mai...

  • Page 246

    During off-road use, loss of traction can temporarily defeat the system and cause the warning light to illumi- nate. Turn the ignition off and on again to restore anti-lock brake system function. Warning! Pumping of the anti-lock brakes will diminish their effectiveness and may lead to an accident. ...

  • Page 247

    Caution! The anti-lock brake system is subject to possible detrimental effects of electronic interference caused by improperly installed aftermarket radios or tele- phones. Note: during severe braking conditions, a pulsing sensation may occur and a clicking noise will be heard. This is normal, indic...

  • Page 248

    Warning! Continued operation with reduced power steering assist could pose a safety risk to yourself and others. Service should be obtained as soon as possible. Caution! Prolong operation of the steering system at the end of the steering wheel travel will increase the steering fluid temperature and ...

  • Page 249

    Off-road driving tips when to use 4l or 4lo (low) range when off-road driving, shift to 4l or 4lo for additional traction and control on slippery or difficult terrain, ascending or descending steep hills, and to increase low-speed pulling power. This range should be limited to extreme situations suc...

  • Page 250

    And/or the flow rate is reduced. If you must cross flowing water avoid depths in excess of 9 inches. The flowing water can erode the streambed causing your vehicle to sink into deeper water. Determine exit point(s) that are downstream of your entry point to allow for drifting. Standing water avoid d...

  • Page 251

    If you stall or begin to lose headway while climbing a steep hill, allow your vehicle to come to a stop and immediately apply the brakes. Restart the engine and shift to r (reverse). Back slowly down the hill allowing the compression braking of the engine to help regulate your speed. If the brakes a...

  • Page 252

    After driving off-road off-road operation puts more stress on your vehicle than does most on-road driving. After going off-road it is always a good idea to check for damage. That way you can get any problems taken care of right away and have your vehicle ready when you need it. • completely inspect ...

  • Page 253

    Tire safety information tire markings note: • p(passenger)-metric tire sizing is based on u.S. Design standards. P-metric tires have the letter “p” molded into the sidewall preceding the size designation. Ex- ample: p215/65r15 95h. • european metric tire sizing is based on european design standards....

  • Page 254

    Tire sizing chart example: size designation: p = passenger car tire size based on u.S. Design standards ⴖ....Blank....ⴖ = passenger car tire based on european design standards lt = light truck tire based on u.S. Design standards t = temporary spare tire 31 = overall diameter in inches (in) 215 = sec...

  • Page 255

    Example: service description: 95 = load index —a numerical code associated with the maximum load a tire can carry. H = speed symbol —a symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions. —the maximum speed corresp...

  • Page 256

    Tire identification number (tin) the tin may be found on one or both sides of the tire however the date code may only be on one side. Tires with white sidewalls will have the full tin including date code located on the white sidewall side of the tire. Look for the tin on the outboard side of black s...

  • Page 257

    Tire loading and tire pressure tire placard location note: the proper cold tire inflation pressure for pas- senger cars is listed on either the face of the driver’s door or the driver’s side “b” pillar. For vehicles other than passenger cars, the cold tire inflation pressures are listed on either th...

  • Page 258

    Tire and loading information placard this placard tells you important information about the: 1) number of people that can be carried in the vehicle 2) the total weight your vehicle can carry 3) the tire size designed for your vehicle 4) the cold tire inflation pressures for the front, rear and spare...

  • Page 259

    Combined weight of occupants, cargo/luggage and trailer tongue weight (if applicable) should never exceed the weight referenced here. Steps for determining correct load limit 1. Locate the statement “the combined weight of occu- pants and cargo should never exceed xxx pounds” on your vehicle’s placa...

  • Page 260

    260 starting and operating.

  • Page 261

    Warning! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. Tires — general information tire pressure proper tire inflation pressur...

  • Page 262

    2. Economy— improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Under inflation also increases tire rolling resistance and results in higher fuel consump- t...

  • Page 263

    Check tire pressure. Do not make a visual judgement when determining proper inflation. Radial tires may look properly inflated even when they are under inflated. Caution! After inspecting or adjusting the tire pressure al- ways reinstall the valve stem cap–if equipped. This will prevent moisture and...

  • Page 264

    Tire pressures for high speed operation the manufacturer advocates driving at safe speeds within posted speed limits. Where speed limits or condi- tions are such that the vehicle can be driven at high speeds, maintaining correct tire inflation pressure is very important. Increased tire pressure and ...

  • Page 265

    Warning! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause tire dam- age or failure. A tire could explode and injure someone. Do not spin your vehicle’s wheels faster than 35 mph (55 km/h) when you are stuck, and do not let anyone near a spinning wheel no m...

  • Page 266

    Life of tire the service life of a tire is dependent upon varying factors including but not limited to: • driving style • tire pressure • distance driven warning! Tires and spare tire should be replaced after six years, regardless of the remaining tread. Failure to follow this warning can result in ...

  • Page 267

    Warning! • do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change sus- pension dimensions and performance characteris- tics, resulting in changes to steering, handling, and braking of your vehicle. This can caus...

  • Page 268

    Improper alignment will not cause vehicle vibration. Vibration may be a result of tire and wheel out-of- balance. Proper balancing will reduce vibration and avoid tire cupping and spotty wear. Tire pressure monitor system (tpms) — if equipped base system the tire pressure monitor system (tpms) uses ...

  • Page 269

    The system will consist of tire pressure monitoring sensors attached to each wheel through the valve stem mounting hole, a central receiver module and a “tire pressure monitoring telltale light.” a sensor is located in the spare wheel if the vehicle is equipped with a match- ing full size spare whee...

  • Page 270

    Caution! After inspecting or adjusting the tire pressure al- ways reinstall the valve stem cap. This will prevent moisture and dirt from entering the valve stem, which could damage the wheel rim sensor. Note: • the tpms can inform the driver of a low tire pressure condition. • the tpms is not intend...

  • Page 271

    When a system fault is detected. The flash cycle will repeat every ten minutes or until the fault condition is removed and reset. The tire pressure monitor system (tpms) consists of the following components: • receiver module • 4/5 wheel sensors • 4 wheel sensor trigger modules • tire pressure monit...

  • Page 272

    Telltale light” will illuminate continuously (solid) and shall remain illuminated until the warning condition is removed/reset. Note: the “tire pressure monitoring telltale light” will only illuminate for the four active road tires. A low spare tire pressure will not cause the “tire pressure monitor...

  • Page 273

    Caution! The tpms has been optimized for the original equipment tires and wheels. Tpms pressures have been established for the tire size equipped on your vehicle. Undesirable system operation or sensor damage may result when using replacement equip- ment that is not of the same size, type, and/or st...

  • Page 274

    General information this device complies with part 15 of the fcc rules and rss 210 of industry canada. Operation is subject to the following conditions: • this device may not cause harmful interference. • this device must accept any interference received, including interference that may cause undesi...

  • Page 275

    Tire chains that are recommended for this vehicle are listed below: • mopar威 p/n 82206828 with p235/70r16 and p235/ 65r17 tires. • mopar威 p/n 82207074 with p215/75r16 tires. Note: in order to avoid damage to tires, chains, and your vehicle do not drive for a prolonged period of time on dry pavement....

  • Page 276

    2.8l turbo diesel engines rotate the tires every 6,000 miles (10 000 km). Note: the premium tire pressure monitor system will automatically locate the pressure values displayed in the correct vehicle position following a tire rotation. The suggested rotation method is the “forward-cross” shown in th...

  • Page 277

    • low humidity light spark knock at low engine speeds is not harmful to your engine. However, continued heavy spark knock at high speeds can cause damage and immediate service is required. Poor quality gasoline can cause problems such as hard starting, stalling and hesitations. If you experience the...

  • Page 278

    Caution! Do not use gasoline containing methanol. Gasoline containing methanol may damage critical fuel system components. Mmt in gasoline mmt is a manganese containing metallic additive that is blended into some gasoline to increase octane. Gasoline blended with mmt provides no performance advantag...

  • Page 279

    • the use of leaded gas is prohibited by federal law. Using leaded gasoline can impair engine performance, damage the emission control system. • an out-of-tune engine, or certain fuel or ignition malfunctions, can cause the catalytic converter to overheat. If you notice a pungent burning odor or som...

  • Page 280

    The vehicle is raised. Have any abnormal conditions repaired promptly. Until repaired, drive with all side windows fully open. • keep the swing gate closed when driving your vehicle to prevent carbon monoxide and other poisonous exhaust gases from entering the vehicle. Fuel requirements (diesel engi...

  • Page 281

    Fuel tank filler cap (gas cap) caution! • to avoid fuel spillage and overfilling, do not “top off” the fuel tank after filling. • do not put gasoline in your diesel vehicle (if equipped). If you accidentally put gasoline in your vehicle, do not start the engine. This will cause damage to the fuel sy...

  • Page 282

    Loose fuel filler cap message if the vehicle diagnostic system determines that the fuel filler cap is loose, improperly installed, or damaged, a “gas cap” message will be displayed in the odometer (located on the instrument cluster). Replace, or tighten the fuel filler cap properly to turn the messa...

  • Page 283

    Common towing definitions the following trailer towing related definitions will assist you in understanding the following information: gross vehicle weight rating (gvwr) the gvwr is the total allowable weight of your vehicle. This includes driver, passengers, cargo and tongue weight. The total load ...

  • Page 284

    Warning! It is important that you do not exceed the maximum front or rear gawr. A dangerous driving condition can result if either rating is exceeded. You could lose control of the vehicle and have an accident. Tongue weight (tw) the downward force exerted on the hitch ball by the trailer. In most c...

  • Page 285

    Trailer hitch classification the rear bumper is intended to tow trailers up to 2,000 lbs (907 kg) without added equipment or alterations to the standard equipment. Your vehicle may be factory equipped for safe towing of trailers weighing over 2,000 lbs (907 kg) with the optional trailer tow prep pac...

  • Page 286

    Engine/ transmission model gvwr (gross vehicle wt. Rating) gcwr (gross combined wt. Rating) frontal area max. Gtw (gross trailer wt.) max. Tongue wt. (see note 1) 3.7l/6-speed manual 4x2 5,350 lbs (2 427 kg) 8,500 lbs (3 855 kg) 40 sq. Ft. (3.72 square meters) 3,500 lbs (1 587 kg) 350 lbs (159 kg) 3...

  • Page 287

    Note 1 – the trailer tongue weight must be considered as part of the combined weight of occupants and cargo, and should never exceed the weight referenced on the tire and loading information placard. Refer to the tire– safety information section in this manual. Trailer and tongue weight always load ...

  • Page 288

    Note: remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options, or dealer-installed options, must be considered as part of the total load on your vehicle. Refer to the tire and loading information plac- ard in the tire safety in...

  • Page 289

    Warning! Improper towing can lead to an injury accident. Follow these guidelines to make your trailer towing as safe as possible: make certain that the load is secured in the trailer and will not shift during travel. When trailering cargo that is not fully secured, dynamic load shifts can occur that...

  • Page 290

    2. Gtw 3. Gawr 4. Tongue weight rating for the trailer hitch utilized (this requirement may limit the ability to always achieve the 10% to 15% range of tongue weight as a percentage of total trailer weight). Towing requirements — tires − do not attempt to tow a trailer while using a compact spare ti...

  • Page 291

    Actuated brakes. When towing a trailer equipped with a hydraulic surge actuated brake system, an electronic brake controller is not required. − trailer brakes are recommended for trailers over 1,000 lbs (454 kg) and required for trailers in excess of 2,000 lbs (907 kg). Caution! If the trailer weigh...

  • Page 292

    Note: do not cut or splice wiring into the vehicles wiring harness. The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector. Refer to the following illustrations. Towing tips before setting out on a trip, practice turning, stopping and backing ...

  • Page 293

    If using a manual transmission vehicle for trailer towing, all starts must be in first gear to avoid excessive clutch slippage. Towing tips — automatic transmission the “d” range can be selected when towing. However, if frequent shifting occurs while in this range, the “3” range should be selected. ...

  • Page 294

    Towing tips — cooling system to reduce potential for engine and transmission over- heating, take the following actions: − city driving when stopped for short periods of time, put transmission in neutral and increase engine idle speed. − highway driving reduce speed. − air conditioning turn off tempo...

  • Page 295

    Note: the transfer case must be shifted into n (neu- tral), and the transmission must be shifted into p (park) (for automatic transmission) or into any forward gear (for manual transmission) for recreational towing. Shifting into neutral (n) use the following procedure to prepare your vehicle for re...

  • Page 296

    Caution! Transmission damage may occur if the automatic transmission is shifted into p (park) with the transfer case in n (neutral) and the engine running. With the transfer case in n (neutral) ensure that the engine is off prior to shifting the transmission into p (park) (refer to steps 7 – 8 above...

  • Page 297

    Caution! Do not use a bumper mounted clamp-on tow bar on your vehicle. The bumper face bar will be damaged. Snow plow snow plows, winches, and other aftermarket equipment should not be added to the front end of your vehicle. The airbag crash sensors may be affected by the change in the front end str...

  • Page 299: Contents

    What to do in emergencies contents 䡵 hazard warning flashers . . . . . . . . . . . . . . . . . 300 䡵 if your engine overheats . . . . . . . . . . . . . . . . . 301 䡵 jacking and tire changing . . . . . . . . . . . . . . . . 302 ▫ jack location . . . . . . . . . . . . . . . . . . . . . . . . 303 ▫ sp...

  • Page 300

    Hazard warning flashers your vehicle’s hazard warning flasher is an emergency warning system. When you activate it, all front and rear directional signals will flash intermittently. Use it when your vehicle is disabled on or near the road. It warns other drivers to steer clear of you and your vehicl...

  • Page 301

    If your engine overheats in any of the following situations, you can reduce the potential for overheating by taking the appropriate ac- tion. • on the highways — slow down. • in city traffic — while stopped, put transmission in n (neutral), but do not increase engine idle speed. Note: there are step...

  • Page 302

    If the coolant temperature of a vehicle equipped with a diesel engine approaches the “h” (hot mark) a warning chime will sound to alert the driver. The air conditioning system will turn off automatically and power loss will occur until the engine temperature returns to the normal range. If the overh...

  • Page 303

    Jack location the scissor-type jack, and tire changing tools are stored beneath the right rear seat. To remove the jack from its stowage position, turn the thumb screw counterclock- wise to loosen jack assembly and then remove it. Spare tire stowage to remove the spare tire from the carrier, remove ...

  • Page 304

    Note: if you have added aftermarket accessories to the spare tire mounted carrier, it cannot exceed a gross weight of 50 lbs (23 kg) including the weight of the spare tire. Preparations for jacking park the vehicle on a firm level surface, avoid ice or slippery areas, set the parking brake and place...

  • Page 305

    4. Locate the jack as shown. For the front tires, place it in the notch on the body weld seam behind wheel to be changed. For the rear tires, place it under the axle by the wheel to be changed. Position the jack handle on the jack. Do not raise the vehicle until you are sure the jack is fully engage...

  • Page 306

    Warning! Raising the vehicle higher than necessary can make the vehicle less stable and cause an accident. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. 6. Remove the lug nuts and wheel. 7. Position the spare wheel/tire on the vehicle and inst...

  • Page 307

    Jump starting — gasoline engines note: check the charge indicator on the battery. If the indicator is light or yellow, replace the battery. 1. Wear eye protection and remove any metal jewelry such as watch bands or bracelets that might make an unintended electrical contact. 2. When boost is provided...

  • Page 308

    Note: to start the vehicle following connection of a booster battery, the security alarm system must first be disabled by cycling a front door key cylinder or by using the keyless entry transmitter. Warning! Jump starting can be dangerous. To avoid personal injury or damage to electrical components ...

  • Page 309

    Warning! Do not attempt to push or tow your vehicle to get it started. Unburned fuel could enter the catalytic converter and, once the engine has started, ignite and damage the converter and vehicle. Emergency tow hooks — if equipped if your vehicle is equipped with tow hooks, they are mounted in th...

  • Page 310

    Towing a disabled vehicle 2wd models only provided the transmission is operable, tow only in n (neutral) at speeds not exceeding 30 mph (48 km/h), for distances of not more than 15 miles (24 km). Towing at more than 30 mph (48 km/h) or for more than 15 miles (24 km) can cause severe transmission dam...

  • Page 311: Maintaining Your Vehicle

    Maintaining your vehicle contents 䡵 3.7l engine . . . . . . . . . . . . . . . . . . . . . . . . . . . 314 䡵 2.8l turbo diesel engine . . . . . . . . . . . . . . . . . 315 䡵 onboard diagnostic system — obd ii . . . . . . . . 316 ▫ loose fuel filler cap message . . . . . . . . . . . . 316 䡵 emissions ...

  • Page 312

    ▫ driveline and steering component lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . 329 ▫ body lubrication . . . . . . . . . . . . . . . . . . . . . 329 ▫ windshield wiper blades . . . . . . . . . . . . . . . . 330 ▫ windshield washers . . . . . . . . . . . . . . . . . . . 330 ▫ exhau...

  • Page 313

    ▫ rear tail, stop, turn signal, and back-up lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 360 ▫ center high mounted stop light (chmsl) . . . 361 䡵 fluid capacities . . . . . . . . . . . . . . . . . . . . . . . . 362 䡵 fluids, lubricants, and genuine parts . . . . . . . . 363 ▫ eng...

  • Page 314

    3.7l engine 314 maintaining your vehicle.

  • Page 315

    2.8l turbo diesel engine maintaining your vehicle 315 7.

  • Page 316

    Onboard diagnostic system — obd ii your vehicle is equipped with a sophisticated onboard diagnostic system called obd ii. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide ex...

  • Page 317

    The fuel filler cap properly to turn the message off (light will time out). If the problem continues, the message will appear the next time the vehicle is started. Emissions inspection and maintenance programs in some localities, it may be a legal requirement to pass an inspection of your vehicle’s ...

  • Page 318

    A. The mil will flash for about 10 seconds and then return to being fully illuminated until you turn off the ignition key or start the engine. This means that your vehicle’s obd system is not ready and you should not proceed to the i/m station. B. The mil will not flash at all and will remain fully ...

  • Page 319

    Note: intentional tampering with emissions control systems can result in civil penalties being assessed against you. Warning! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the proper equipment. If you have any doubt abou...

  • Page 320

    The best time to check the engine oil level is about 5 minutes after a fully warmed engine has been shut off, or before starting the engine after it has sat overnight. Checking the oil while the vehicle is on level ground will improve the accuracy of the oil level readings. Maintain the oil level be...

  • Page 321

    If any of these apply to you, then change your engine oil at every interval shown in schedule “b” of the “mainte- nance schedules” section of this manual. If none of these apply to you, then change your engine oil at every interval shown on schedule “a” of the “main- tenance schedules” section of th...

  • Page 322

    Lubricants which do not have both, the engine oil certi- fication mark and the correct sae viscosity grade num- ber should not be used. Engine oil selection (diesel engines) for best performance and maximum protection for all engines under all types of operating conditions, the manufacturer recommen...

  • Page 323

    Disposing of used engine oil care should be taken in disposing of used engine oil from your vehicle. Used oil and oil filters, indiscriminately discarded, can present a problem to the environment. Contact your authorized dealer, service station, or gov- ernmental agency for advice on how and where u...

  • Page 324

    Spark plugs spark plugs must fire properly to assure engine perfor- mance and emission control. New plugs should be in- stalled at the mileage specified in the appropriate main- tenance chart. The entire set should be replaced if there is any malfunction due to a faulty spark plug. Refer to the “veh...

  • Page 325

    Warning! A hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your ex- haust system. Do not park or operate your vehicle in areas where your exhaust system can contact any- thing that can burn. In unusual sit...

  • Page 326

    Crankcase emission control system proper operation of this system depends on freedom from sticking or plugging due to deposits. As vehicle mileage builds up, the pcv valve and passages may accumulate deposits. If a valve is not working properly, replace it with a new valve. Do not attempt to clean t...

  • Page 327

    Warning! Battery posts, terminals, and related accessories con- tain lead and lead compounds. Always wash hands after handling the battery. To determine the battery charge, check the battery test indicator (if equipped) on top of the battery. Refer to the illustration. Caution! It is essential when ...

  • Page 328

    Warning! • use only refrigerants and compressor lubricants approved by the manufacturer for your air condi- tioning system. Some unapproved refrigerants are flammable and can explode, injuring you. Other unapproved refrigerants or lubricants can cause the system to fail, requiring costly repairs. Re...

  • Page 329

    Warning! Fluid level should be checked on a level surface with the engine off to prevent injury from moving parts, and to insure accurate fluid level reading. Do not overfill. Use only the manufacturer’s recommended fluid. If necessary, add fluid to restore to the proper indicated level. With a clea...

  • Page 330

    Attention should also be given to hood latching compo- nents to insure proper function. When performing other underhood services, the hood latch, release mechanism and safety catch should be cleaned and lubricated. The external lock cylinders should be lubricated twice a year, preferably in the fall...

  • Page 331

    Should be checked for fluid level at regular intervals. Fill the reservoir with windshield washer solvent (not antifreeze/coolant) and operate the system for a few seconds to flush out the residual water. Warning! Commercial windshield washer solvents are flam- mable. They could ignite and burn you....

  • Page 332

    Cooling system warning! You or others can be badly burned by hot antifreeze/ coolant or steam from your radiator. If you see or hear steam coming from under the hood, don’t open the hood until the radiator has had time to cool. Never try to open a cooling system pressure cap when the radiator or coo...

  • Page 333

    Selection of engine coolant use only the manufacturer’s recommended antifreeze/ coolant, refer to fluids, lubricants, and genuine parts for correct antifreeze/coolant type. Caution! • mixing of antifreeze/coolant other than the speci- fied hoat antifreeze/coolant may result in de- creased corrosion ...

  • Page 334

    Adding engine coolant your vehicle has been built with an improved antifreeze/ coolant that allows extended maintenance intervals. This antifreeze/coolant can be used up to 5 years or 100,000 miles before replacement. To prevent reducing this ex- tended maintenance period, it is important that you u...

  • Page 335

    The cap should be inspected and cleaned if there is any accumulation of foreign material on the sealing surfaces. Warning! The warning words do not open hot on the cooling system pressure cap are a safety precaution. Never add antifreeze/coolant when the engine is overheated. Do not loosen or remove...

  • Page 336

    When additional antifreeze/coolant is needed to main- tain the proper level, it should be added to the coolant recovery bottle. Do not overfill. Points to remember note: when the vehicle is stopped after a few miles (kilometers) of operation, you may observe vapor coming from the front of the engine...

  • Page 337

    Only the correct type thermostat. Other designs may result in unsatisfactory cooling performance, poor gas mileage, and increased emissions. Hoses and vacuum/vapor harnesses inspect surfaces of hoses and nylon tubing for evidence of heat and mechanical damage. Hard or soft spots, brittle rubber, cra...

  • Page 338

    Brake and power steering system hoses when servicing the vehicle for scheduled maintenance, inspect surface of hoses for evidence of heat and me- chanical damage. Hard and brittle rubber, cracking, tears, cuts, abrasion, and excessive swelling suggest deteriora- tion of the rubber. Particular attent...

  • Page 339

    Be sure to clean the top of the master cylinder area before removing the cap. If necessary, add fluid to bring the fluid level up to the requirements described on the brake fluid reservoir. With disc brakes, fluid level can be expected to fall as the brake pads wear. However, low fluid level may be ...

  • Page 340

    Use only brake fluid that has been in a tightly closed container to avoid contamination from foreign matter. Do not allow petroleum base fluid to contaminate the brake fluid as seal damage will result. Automatic transmission selection of lubricant it is important that the proper lubricant is used in...

  • Page 341

    To check the automatic transmission fluid level properly, the following procedure must be used: 1. The vehicle must be on level ground. 2. The engine should be running at curb idle speed for a minimum of 60 seconds. 3. Fully apply parking brake. 4. Apply the brakes and shift the transmission into p ...

  • Page 342

    Hydraulic clutch fluid — manual transmission the clutch hydraulic system is a sealed maintenance free system. In the event of leakage or other malfunction, the system must be replaced. Manual transmission selection of lubricant use only manufacturer’s recommended manual trans- mission fluid, refer t...

  • Page 343

    Adding fluid only at filler hole until fluid runs out of the hole, when the vehicle is in a level position. Drain first remove fill plug (b), then drain plug (c). Recom- mended tightening torque for drain and fill plugs is 15–25 ft. Lbs. (20–34 n·m). Caution! When installing plugs, do not overtighte...

  • Page 344

    Adding fluid add lubricant only at the fill hole and only to the level specified above. Selection of lubricant use only manufacturer’s recommended fluid, refer to fluids, lubricants, and genuine parts for correct fluid type. Maintenance after off-pavement driving after extended operation in mud, san...

  • Page 345

    Appearance care and protection from corrosion protection of body and paint from corrosion vehicle body care requirements vary according to geo- graphic locations and usage. Chemicals that make roads passable in snow and ice, and those that are sprayed on trees and road surfaces during other seasons,...

  • Page 346

    • use mopar威 cleaner wax to remove road film, stains, and to protect your paint finish. Take care never to scratch the paint. • avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish. Caution! Do not use abrasive or strong cleaning materials such as...

  • Page 347

    Oven cleaner. Avoid automatic car washes that use acidic solutions or harsh brushes that may damage the wheels’ protective finish. • if you carry special cargo such as chemicals, fertilizers, de-icer salt, etc., assure that such materials are well packaged and sealed. • if a lot of driving is done o...

  • Page 348

    Warning! Do not use volatile solvents for cleaning purposes. Many are potentially flammable, and if used in closed areas they may cause respiratory harm. Glass surfaces all glass surfaces should be cleaned on a regular basis with mopar 威 glass cleaner or any commercial household-type glass cleaner. ...

  • Page 349

    Fuse panel interior fuses the fuse panel is on the left side of the instrument panel. A label is attached to the fuse panel cover to identify each fuse for ease of replacement. Cavity fuse description 1 15 amp blue horn relay, power sunroof relay, power window relay 2 10 amp red rear fog lights (exp...

  • Page 350

    Cavity fuse description 13 10 amp red body control module/ cmtc/cluster/pass. Airbag on,off indicator, auto day- light mirror/light bar switch (renegade only) 14 10 amp red pdc fuel pump/ac clutch, starter relay/engine controller/transmission controller (diesel only) 15 spare 16 20 amp yellow power ...

  • Page 351

    Cavity fuse description 34 15 amp blue body control module/ cluster/interior lights, hands free module/radio/ cmtc/itm module & siren (export only) 35 spare 36 10 amp red airbag control module/ occupation classification module (right front seat) 37 10 amp red airbag control module 38 10 amp red abs ...

  • Page 352

    Power distribution center (gasoline engines) cavity fuse description f1 40 amp green blower motor f2 40 amp green radiator fan f3 50 amp red jb power f4 40 amp green abs pump f5 20 amp yellow ngc trans f6 30 amp pink asd f7 50 amp red jb power f8 40 amp green ign/start f9 50 amp red jb power f10 30 ...

  • Page 353

    Cavity fuse description f16 open f17 open f18 open f19 30 amp pink rear window defogger (hbl) f20 open f21 20 amp yellow a/c clutch f22 open f23 open f24 20 amp yellow fuel pump f25 20 amp yellow abs valves f26 25 amp natural injectors f27 open f28 15 amp blue starter r29 half iso relay fuel pump r3...

  • Page 354

    Power distribution center (diesel engines) cavity fuse description f1 40 amp green blower motor f2 40 amp green radiator fan f3 50 amp red jb power f4 40 amp green abs pump f5 open f6 30 amp pink asd f7 50 amp red jb power f8 40 amp green ign/start f9 50 amp red jb power f10 30 amp pink trailer tow ...

  • Page 355

    Cavity fuse description r31 half iso relay wiper on/off r32 half iso relay wiper hi/lo r33 full iso relay h. Blower r34 full iso relay rad. Fan hi r35 half iso relay a/c clutch r36 half iso relay viscous heat r37 open r38 open r39 full iso relay asd r40 full iso relay rad. Fan lo vehicle storage if ...

  • Page 356

    Replacement bulbs interior lights bulb type a/c heater . . . . . . . . . . . . . . . . . . . . Not serviceable ashtray receiver light . . . . . . . . . . . . . . . . . . . . 161 climate control (manual a/c). . . . . . . . . . . . . . . . 74 front reading . . . . . . . . . . . . . . . . . . . . . . ....

  • Page 357

    3. Firmly grasp the lock ring on the back of the headlamp unit housing. 4. Rotate the lock ring on the back of the headlamp housing counter-clockwise to unlock it. Caution! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact wi...

  • Page 358

    3. Rotate the bulb socket counter-clockwise to unlock it. Caution! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol. 4. Disconnect the electrical connector and repla...

  • Page 359

    4. Pivot the retainer clip up off of the bulb flange and out of the way. Caution! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol. 5. Pull the bulb straight out of ...

  • Page 360

    Caution! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol. 5. Replace the bulb. Rear tail, stop, turn signal, and back-up lights 1. Open the swing gate. 2. Remove th...

  • Page 361

    Center high mounted stop light (chmsl) 1. Remove the two screws securing the chmsl. 2. Twist the bulb socket to remove from the chmsl housing. 3. Pull the bulb out of the socket. 4. Replace the bulb, reinstall the socket and reattach the chmsl. Maintaining your vehicle 361 7.

  • Page 362

    Fluid capacities u.S. Metric fuel (approximate) 20.5 gallons 78 liters engine oil with filter 3.7 liter engines (sae 5w-30, api certified engine oil) 5 qts 4.7 liters 2.8 liter diesel engine (sae 0w-40 synthetic engine oil) 6.4 qts 6.1 liters cooling system * 3.7 liter engine (mopar 威 antifreeze/coo...

  • Page 363

    Fluids, lubricants, and genuine parts engine component fluid, lubricant, or genuine part engine coolant mopar 威 antifreeze/coolant 5 year/100,000 mile formula hoat (hybrid organic ad- ditive technology) engine oil (3.7l engines) use api certified sae 5w-30 engine oil, meeting the requirements of dai...

  • Page 364

    Chassis component fluid, lubricant, or genuine part automatic transmission mopar 威 atf+4 automatic transmission fluid manual transmission mopar 威 manual transmission lubricant or equivalent (meeting the re- quirements of daimlerchrysler material standard ms-9224) transfer case mopar 威 atf+4 automati...

  • Page 365: Maintenance Schedules

    Maintenance schedules contents 䡵 emission control system maintenance . . . . . . . . 366 䡵 maintenance schedules — gasoline engines . . . . 366 ▫ schedule “b” — gasoline engines . . . . . . . . . 369 ▫ schedule “a” — gasoline engines . . . . . . . . . 379 䡵 maintenance schedules — diesel engines . ....

  • Page 366

    Emission control system maintenance the “scheduled” maintenance services, listed in bold type must be done at the times or mileages specified to assure the continued proper functioning of the emission control system. These, and all other maintenance services included in this manual, should be done t...

  • Page 367

    • heavy loading. • taxi, police, or delivery service (commercial service). • off-road or desert driving. • if equipped for and operated with e-85 (ethanol) fuel. Note: if any of these apply to you then change your engine oil every 3,000 miles (5 000 km) or 3 months, whichever comes first and follow ...

  • Page 368

    • check the windshield washer solvent, add as required. Once a month • check the tire pressure and look for unusual wear or damage. • inspect the battery, and clean and tighten the terminals as required. • check the fluid levels of the engine coolant/anti- freeze reservoir, brake master cylinder, an...

  • Page 369

    Schedule “b” — gasoline engines follow schedule “b” if you usually operate your vehicle under one or more of the following conditions. • day or night temperatures are below 32°f (0°c). • stop and go driving. • extensive engine idling. • driving in dusty conditions. • short trips of less than 10 mile...

  • Page 370

    Miles 3,000 6,000 9,000 12,000 15,000 (kilometers) (5 000) (10 000) (15 000) (20 000) (25 000) change the engine oil and engine oil filter, if not replaced at 3 months. X x x x x rotate the tires. X x inspect the engine air filter element, replace if necessary. X inspect the brake linings. X drain a...

  • Page 371

    Miles 18,000 21,000 24,000 27,000 30,000 (kilometers) (30 000) (35 000) (40 000) (45 000) (50 000) change the engine oil and engine oil filter, if not replaced at 3 months. X x x x x rotate the tires. X x x inspect the engine air filter element, replace if necessary. X replace the spark plugs. X ins...

  • Page 372

    Miles 33,000 36,000 39,000 42,000 45,000 (kilometers) (55 000) (60 000) (65 000) (70 000) (75 000) change the engine oil and engine oil filter, if not replaced at 3 months. X x x x x rotate the tires. X x inspect the engine air filter element, replace if necessary. X inspect the brake linings. X dra...

  • Page 373

    Miles 48,000 51,000 54,000 57,000 60,000 (kilometers) (80 000) (85 000) (90 000) (95 000) (100 000) change the engine oil and engine oil filter, if not replaced at 3 months. X x x x x rotate the tires. X x x inspect the engine air filter element, replace if necessary. X replace the spark plugs. X in...

  • Page 374

    Miles 63,000 66,000 69,000 72,000 75,000 (kilometers) (105 000) (110 000) (115 000) (120 000) (125 000) change the engine oil and engine oil filter, if not replaced at 3 months. X x x x x rotate the tires. X x inspect the engine air filter element, replace if necessary. X inspect the brake linings. ...

  • Page 375

    Miles 78,000 81,000 84,000 87,000 90,000 (kilometers) (130 000) (135 000) (140 000) (145 000) (150 000) change the engine oil and engine oil filter, if not replaced at 3 months. X x x x x rotate the tires. X x x inspect the engine air filter element, replace if necessary. X replace the spark plugs. ...

  • Page 376

    Miles 93,000 96,000 99,000 102,000 105,000 (kilometers) (155 000) (160 000) (165 000) (170 000) (175 000) change the engine oil and engine oil filter, if not replaced at 3 months. X x x x x rotate the tires. X x inspect the engine air filter element, replace if necessary. X inspect the brake linings...

  • Page 377

    Miles 108,000 111,000 114,000 117,000 120,000 (kilometers) (180 000) (185 000) (190 000) (195 000) (200 000) change the engine oil and engine oil filter, if not replaced at 3 months. X x x x x rotate the tires. X x x inspect the engine air filter element, replace if necessary. X replace the spark pl...

  • Page 378

    Miles 108,000 111,000 114,000 117,000 120,000 (kilometers) (180 000) (185 000) (190 000) (195 000) (200 000) drain and refill the transfer case fluid. X flush and replace the engine coolant/anti-freeze at 120 months, if not replaced at 102,000 miles (170 000 km). X inspection and service should be p...

  • Page 379

    Schedule “a” — gasoline engines miles 6,000 12,000 18,000 24,000 30,000 (kilometers) (10 000) (20 000) (30 000) (40 000) (50 000) [months] [6] [12] [18] [24] [30] change the engine oil and engine oil filter. X x x x x rotate the tires. X x x x x inspect the engine air filter element, and replace if ...

  • Page 380

    Miles 36,000 42,000 48,000 54,000 (kilometers) (60 000) (70 000) (80 000) (90 000) [months] [36] [42] [48] [54] change the engine oil and engine oil filter. X x x x rotate the tires. X x x x inspect the brake linings. X x 380 schedule “a” — gasoline engines 8 m a i n t e n a n c e s c h e d u l e s.

  • Page 381

    Miles 60,000 66,000 72,000 78,000 (kilometers) (100 000) (110 000) (120 000) (130 000) [months] [60] [66] [72] [78] change the engine oil and engine oil filter. X x x x rotate the tires. X x x x inspect the engine air filter element, and replace if nec- essary. X replace the spark plugs. X inspect a...

  • Page 382

    Miles 84,000 90,000 96,000 102,000 (kilometers) (140 000) (150 000) (160 000) (170 000) [months] [84] [90] [96] [102] change the engine oil and engine oil filter. X x x x rotate the tires. X x x x inspect the engine air filter element, and replace if nec- essary. X replace the spark plugs. X inspect...

  • Page 383

    Miles 108,000 114,000 120,000 (kilometers) (180 000) (190 000) (200 000) [months] [108] [114] [120] change the engine oil and engine oil filter. X x x rotate the tires. X x x inspect the engine air filter element, and replace if necessary. X replace the spark plugs. X inspect and replace the pcv val...

  • Page 384

    Maintenance schedules — diesel engines there are two maintenance schedules that show the required service for your vehicle. First is schedule ⴖbⴖ. It is for vehicles that are operated under the conditions that are listed below and at the beginning of the schedule. • day or night temperatures are bel...

  • Page 385

    At each stop for fuel • check the engine oil level about 5 minutes after a fully warmed engine is shut off. Checking the oil level while the vehicle is on level ground will improve the accu- racy of the oil level reading. Add oil only when the level is at or below the add or min mark. • check the wi...

  • Page 386

    Schedule “b” — diesel engines follow schedule “b” if you usually operate your vehicle under one or more of the following conditions. • day or night temperatures are below 32°f (0°c). • stop and go driving. • extensive engine idling. • driving in dusty conditions. • short trips of less than 10 miles ...

  • Page 387

    Miles 6,250 12,500 18,750 25,000 31,250 (kilometers) (10 000) (20 000) (30 000) (40 000) (50 000) change the engine oil and engine oil filter. X x x x x inspect the engine air filter element. Replace as necessary. X x x replace the engine air filter element. X x inspect the boost pressure solenoid f...

  • Page 388

    Miles 37,500 43,750 50,000 56,250 62,500 (kilometers) (60 000) (70 000) (80 000) (90 000) (100 000) change the engine oil and engine oil filter. X x x x x inspect the engine air filter element. Replace as necessary. X x replace the engine air filter element. X x x inspect the boost pressure solenoid...

  • Page 389

    Miles 68,750 75,000 81,250 87,500 93,750 100,000 (kilometers) (110 000) (120 000) (130 000) (140 000) (150 000) (160 000) change the engine oil and engine oil filter. X x x x x x inspect the engine air filter element. Re- place as necessary. X x x replace the engine air filter element. X x x inspect...

  • Page 390

    Miles 68,750 75,000 81,250 87,500 93,750 100,000 (kilometers) (110 000) (120 000) (130 000) (140 000) (150 000) (160 000) inspect the brake linings. X x drain and refill the front and rear axle fluid. X x 〫 applies only if vehicle is used for frequent trailer towing, or fleet/commercial service. † t...

  • Page 391

    Schedule “a” — diesel engines miles 12,500 25,000 37,500 50,000 (kilometers) (20 000) (40 000) (60 000) (80 000) change the engine oil and engine oil filter. X x x x inspect the engine air filter element. Replace as neces- sary. X x replace the engine air filter element. X x inspect the boost pressu...

  • Page 392

    Miles 62,500 75,000 87,500 100,000 (kilometers) (100 000) (120 000) (140 000) (160 000) change the engine oil and engine oil filter. X x x x inspect the engine air filter element. Replace as necessary. X x replace the engine air filter element. X x inspect the boost pressure solenoid filter. Replace...

  • Page 393: Contents

    If you need consumer assistance contents 䡵 suggestions for obtaining service for your vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 394 ▫ prepare for the appointment . . . . . . . . . . . . 394 ▫ prepare a list . . . . . . . . . . . . . . . . . . . . . . . . 394 ▫ be reasonable...

  • Page 394

    Suggestions for obtaining service for your vehicle prepare for the appointment if you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty, discuss additional charges with the service manager. ...

  • Page 395

    Technicians, special tools, and the latest information to assure your vehicle is fixed correctly and in a timely manner. This is why you should always talk to your dealer’s service manager first. Most matters can be resolved with this process. • if for some reason you are still not satisfied, talk t...

  • Page 396

    Customer assistance for the hearing or speech impaired (tdd/tty) to assist customers who have hearing difficulties, the manufacturer has installed special tdd (telecommuni- cation devices for the deaf) equipment at its customer center. Any hearing or speech impaired customer who has access to a tdd ...

  • Page 397

    Warranty information (u.S. Vehicles only) see the warranty information booklet for the terms and provisions of daimlerchrysler’s warranties applicable to this vehicle. Mopar 姞 parts mopar 威 fluids, lubricants, parts, and accessories are available from your dealer. They will help you keep your vehicl...

  • Page 398

    Publication order forms to order the following manuals, you may use either the website or the phone numbers listed below. Visa, mas- tercard, american express, and discover orders are ac- cepted. If you prefer mailing your payment, please call for an order form. Note: a street address is required wh...

  • Page 399

    Call toll free at: • 1–800–890–4038 (u.S.) • 1–800–387–1143 (canada) or visit us on the world wide web at: • www.Techauthority.Daimlerchrysler.Com • www.Daimlerchrysler.Ca/manuals department of transportation uniform tire quality grades the following describes the tire grading categories estab- lish...

  • Page 400

    On specified government test surfaces of asphalt and concrete. A tire marked c may have poor traction perfor- mance. Warning! The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction chara...

  • Page 401: Index

    Index 10

  • Page 402

    Abs (anti-lock brake system) . . . . . . . . . . . . 175,245 adding washer fluid . . . . . . . . . . . . . . . . . . . . . 163 air cleaner, engine (engine air cleaner filter) . . . 326 air conditioner maintenance . . . . . . . . . . . . . . . 327 air conditioning, operating tips . . . . . . . . . . ...

  • Page 403

    Bar, light . . . . . . . . . . . . . . . . . . . . . . . . . . . 119,359 battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 326 emergency starting . . . . . . . . . . . . . . . . . . . . . 307 keyless transmitter replacement (rke) . . . . . . . 27 saving feature (protection) . . ....

  • Page 404

    Caution, exhaust gas . . . . . . . . . . . . . . . . . . . 72,147 cd (compact disc) changer . . . . . . . . . . . . . 189,199 cd (compact disc) player . . . . . . . . . 185,187,191,194 cd (compact disc) player maintenance . . . . . . . . 207 cellular phone . . . . . . . . . . . . . . . . . . . . . ....

  • Page 405

    Temperature gauge . . . . . . . . . . . . . . . . . . . . . 176 crankcase emission control system . . . . . . . . . . 326 cruise control (speed control) . . . . . . . . . . . . . . 133 cruise light . . . . . . . . . . . . . . . . . . . . . . . . . . . 177 cup holder . . . . . . . . . . . . . . . . ....

  • Page 406

    Electronic stability program (esp) . . . . . . . . . . . . 129 electronic throttle control warning light . . . . . . 180 electronic vehicle information center (evic) . . . . 137 emergency, in case of freeing vehicle when stuck . . . . . . . . . . . . . . . 233 hazard warning flasher . . . . . . . . ...

  • Page 407

    Exhaust gas caution . . . . . . . . . . . . . . . . . . . 72,279 exhaust system . . . . . . . . . . . . . . . . . . . . . . . . . 331 exterior finish care . . . . . . . . . . . . . . . . . . . . . . 345 filters air cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . 326 engine oil . . . . . ...

  • Page 408

    Octane rating . . . . . . . . . . . . . . . . . . . . . . . . 276 requirements . . . . . . . . . . . . . . . . . . . 276,280,362 tank capacity . . . . . . . . . . . . . . . . . . . . . . . . 362 fuel system caution . . . . . . . . . . . . . . . . . . . 278,282 fuses . . . . . . . . . . . . . . . . ....

  • Page 409

    Hitches trailer towing . . . . . . . . . . . . . . . . . . . . . . . . 285 holder, cup . . . . . . . . . . . . . . . . . . . . . . . . . . . 155 homelink 威 (garage door opener) transmitter . . . 145 hood release . . . . . . . . . . . . . . . . . . . . . . . . . . 114 hoses . . . . . . . . . . . . . ...

  • Page 410

    Lane change and turn signals . . . . . . . . . . . . . . 173 lap/shoulder belts . . . . . . . . . . . . . . . . . . . . . . . 36 latch (lower anchors and tether for children) . . . . . 65,66 lead free gasoline . . . . . . . . . . . . . . . . . . . . . . 276 life of tires . . . . . . . . . . . . . . ...

  • Page 411

    Malfunction indicator (check engine) . . . . . . . . 174 map reading . . . . . . . . . . . . . . . . . . . . . . . . . 116 oil pressure . . . . . . . . . . . . . . . . . . . . . . . . . . 177 park . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116 passing . . . . . . . . . . . . . . ....

  • Page 412

    Diesel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 384 light duty schedule “a” . . . . . . . . . . . . . . 379,391 light duty schedule “b” . . . . . . . . . . . . . . 369,386 schedule “a” . . . . . . . . . . . . . . . . . . . . . . 379,391 schedule “b” . . . . . . . . . . . . . . . ....

  • Page 413

    Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . 362 change interval . . . . . . . . . . . . . . . . . . . . . . . 320 checking . . . . . . . . . . . . . . . . . . . . . . . . . . . . 319 dipstick . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 319 identification logo . . ....

  • Page 414

    Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 pregnant women and seat belts . . . . . . . . . . . . . . 46 preparation for jacking . . . . . . . . . . . . . . . . . . . . 304 pretensioners seat belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 programmable ele...

  • Page 415

    Restraints, occupant . . . . . . . . . . . . . . . . . . . . . . 34 retractable cargo area cover . . . . . . . . . . . . . . . 157 rocking vehicle when stuck . . . . . . . . . . . . . . . . 233 roof rack (luggage rack) . . . . . . . . . . . . . . . . . 164 rotation, tires . . . . . . . . . . . . . ....

  • Page 416

    Sentry key (immobilizer) . . . . . . . . . . . . . . . . . . . 14 sentry key programming . . . . . . . . . . . . . . . . . . . 16 sentry key replacement . . . . . . . . . . . . . . . . . . . 15 service assistance . . . . . . . . . . . . . . . . . . . . . . . 394 service contract . . . . . . . . . . ...

  • Page 417

    Storage, vehicle . . . . . . . . . . . . . . . . . . . . . . . . . 355 storing your vehicle . . . . . . . . . . . . . . . . . . . . . . 355 sun roof . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151 sun visor extension . . . . . . . . . . . . . . . . . . . . . . . 82 sunroof maintenanc...

  • Page 418

    Sizes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 254 spare tire . . . . . . . . . . . . . . . . . . . . . . . . . . . 303 spinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . 264 tread wear indicators . . . . . . . . . . . . . . . . . . . 265 tongue weight/trailer weig...

  • Page 419

    Turbo cool down . . . . . . . . . . . . . . . . . . . . . . . 220 turn signals . . . . . . . . . . . . . . . . . . . 117,173,357,360 underhood fuses . . . . . . . . . . . . . . . . . . . . . . . . 351 uniform tire quality grades . . . . . . . . . . . . . . . . 399 universal transmitter . . . . . . ....

  • Page 420: Notes

    Notes.

  • Page 421: Notes

    Notes.

  • Page 422: Notes

    Notes.

  • Page 423: Notes

    Notes.

  • Page 424: Notes

    Notes.