1. DL manuals
  2. Jeep
  3. Automobile
  4. 2006 Wrangler
  5. Owner's Manual

Jeep 2006 Wrangler Owner's Manual

Summary of 2006 Wrangler

  • Page 1

    Table of contents section page 1 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 things to know before starting your vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 3 understanding the fea...

  • Page 3: Introduction

    Introduction contents 䡵 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 ▫ roll over warning . . . . . . . . . . . . . . . . . . . . . 4 䡵 how to use this manual . . . . . . . . . . . . . . . . . . 7 䡵 warnings and cautions . . . . . . . . . . . . . . . . . . . 7 䡵 vehicle identi...

  • Page 4

    Introduction thank you for selecting a jeep 威 wrangler and welcome to our worldwide family. This is a specialized utility vehicle designed for both on-road and off-road use. It can go places and perform tasks for which conventional two-wheel drive enclosed vehicles were not intended. It handles and ...

  • Page 5

    Control. Failure to operate this vehicle safely may result in an accident, roll over of the vehicle and serious injury or death. Because of its open-body construction, your vehicle offers less protection than closed vehicles in the event of an accident. Failure to use driver and passenger seat belts...

  • Page 6

    Operating this vehicle at excessive speeds or while intoxicated may result in loss of control, collision with other vehicles or objects, going off the road, or overturn- ing, any of which may lead to serious injury or death. Also, failure to use standard seat belts subjects the driver and passengers...

  • Page 7

    Warning! Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the state of california to cause cancer and birth defects or other reproductive harm. In addition, certain fluids contained in vehicles and certain prod- ucts of component wear contai...

  • Page 8

    Vehicle identification number the vehicle identification number (vin) is found on a stamped plate located on the left front corner of the instrument panel pad, visible from outside of vehicle through windshield. This number also appears on the automobile information disclosure label affixed to a win...

  • Page 9

    Vehicle modifications / alterations warning! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death. Introduction 9 1.

  • Page 11: Contents

    Things to know before starting your vehicle contents 䡵 a word about your keys . . . . . . . . . . . . . . . . . .13 ▫ ignition key . . . . . . . . . . . . . . . . . . . . . . . . . .13 ▫ key-in-ignition reminder . . . . . . . . . . . . . . . .14 䡵 sentry key immobilizer system — if equipped . .14 ▫ ...

  • Page 12

    ▫ seat belt extender . . . . . . . . . . . . . . . . . . . . . .26 ▫ driver and front passenger supplemental restraint systems (srs) — airbags . . . . . . . . . .27 ▫ child restraint . . . . . . . . . . . . . . . . . . . . . . . .34 䡵 engine break-in recommendations . . . . . . . . . . .44 䡵 safety ...

  • Page 13

    A word about your keys the keys for your new vehicle are enclosed in a plastic bag with the key code number on it. If you received your keys without the bag, ask your dealer to give you the number. The key code can also be obtained by the dealer from your vehicle invoice. Ignition key insert the key...

  • Page 14

    To remove the ignition key on models with a manual transmission, depress and hold the key release button, turn the ignition key to lock, and remove the key. Key-in-ignition reminder opening the driver’s door when the key is in the ignition, sounds a signal to remind you to remove the key. Caution! A...

  • Page 15

    Keys that have been programmed to the vehicle can be used to start and operate the vehicle for longer than the 2 second validation time period. The sentry key immobilizer system does not need to be armed or activated. Operation of the system is automatic regardless of whether or not the vehicle is l...

  • Page 16

    Important note about service a four digit pin number is needed to service the sentry key immobilizer system. This number can be obtained from your authorized dealer. However, this number can also be found on your customer invoice that you were given upon receipt of your vehicle. Replacement keys not...

  • Page 17

    3. Insert the second valid key and turn the ignition switch on within 15 seconds. After ten seconds, a chime will sound and the skim indicator light will begin to flash. Turn the ignition switch off and remove the second key. 4. Insert a blank sentry key into the ignition switch and turn the ignitio...

  • Page 18

    To manually lock the steering wheel with the engine running, rotate the steering wheel 1/2 revolution from straight ahead position, turn off the engine and remove the key. Rotate the steering wheel slightly in both directions until the lock engages. To release the steering wheel lock insert the key ...

  • Page 19

    Door locks doors on both hard-top and soft-top models are equipped with a rocker-type interior door lock. To lock a door when leaving your vehicle, press to the “lock” position and close the door. Warning! • for personal security reasons and safety in an accident, lock the vehicle doors when you dri...

  • Page 20

    You will be carrying children too small for adult-size belts, your seat belts can also be used to hold infant and child restraint systems. Please pay close attention to the information in this section. It tells you how to use your restraint system properly to keep you and your passengers as safe as ...

  • Page 21

    Normal conditions. But in a collision, the belt will lock and reduce the risk of your striking the inside of the vehicle or being thrown out. Warning! • it is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to ...

  • Page 22

    Lap/shoulder belt operating instructions 1. Enter the vehicle and close the door. Sit back and adjust the seat. 2. The seat belt latch plate is above the back of the front seat, next to your arm in the rear seat. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as fa...

  • Page 23

    Warning! • a belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • a belt that is loose will not protect you as well. In a sudden stop you ...

  • Page 24

    Warning! • a lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as possible and keep it snug. • a twisted belt cannot do its job as well. In a collision ...

  • Page 25

    Warning! A frayed or torn belt could rip apart in a collision and leave you with no protection. Inspect the belt system periodically, checking for cuts, frays, or loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Seat belt assemblies must be replaced a...

  • Page 26

    Seat belts and pregnant women we recommend that pregnant women use seat belts throughout their pregnancy. Keeping the mother safe is the best way to keep the baby safe. Pregnant women should wear the lap part of the belt across the thighs and as snug across the hips as possible. Keep the belt low so...

  • Page 27

    Driver and front passenger supplemental restraint systems (srs) — airbags this vehicle has front airbags for both the driver and front passenger as a supplement to the seat belt restraint system. The driver’s front airbag is mounted in the center of the steering wheel. The passenger’s front airbag i...

  • Page 28

    Airbags inflate in moderate to high speed impacts. Along with the seat belts, front airbags work with the instru- ment panel knee bolsters to provide improved protection for the driver and front passenger. The seat belts are designed to protect you in many types of collisions. The front airbags depl...

  • Page 29

    You should read the instructions provided with your child restraint to make sure that you are using it properly. 2. All occupants should use their lap and shoulder belts properly. 3. The driver and front passenger seats should be moved back as far as practical to allow the front airbags room to infl...

  • Page 30

    Airbag system components the airbag system consists of the following: • occupant restraint control (orc) module • airbag warning light • driver airbag • passenger airbag • steering wheel and column • instrument panel • crash sensor • interconnecting wiring • knee impact bolsters how the airbag syste...

  • Page 31

    Orc detects a malfunction, the “airbag warning light” will illuminate for a minimum of 12 seconds and will remain illuminated as long as the malfunction exists. Warning! Ignoring the “airbag warning light” in your instru- ment panel could mean you won’t have the airbags to protect you in a collision...

  • Page 32

    If a deployment occurs the airbag system is designed to deploy when the impact sensors detect a moderate-to-severe frontal collision, to help restrain the driver and front passenger, and then to immediately deflate. Note: a frontal collision that is not severe enough to need airbag protection will n...

  • Page 33

    Warning! Deployed airbags cannot protect you in another collision. Have the airbags replaced by an autho- rized dealer as soon as possible. Maintaining your airbag system warning! • modifications to any part of the airbag system could cause it to fail when you need it. You could be injured because t...

  • Page 34

    Airbag warning light you will want to have the airbags ready to inflate for your protection in an collision. While the airbag system is designed to be maintenance free, if any of the following occurs, have an authorized dealer service the system immediately. • the “airbag warning light” does not com...

  • Page 35

    Warning! In a collision, an unrestrained child, even a tiny baby, can become a missile inside the vehicle. The force required to hold even an infant on your lap can become so great that you could not hold the child, no matter how strong you are. The child and others could be badly injured. Any child...

  • Page 36

    The child seat is held in the vehicle by the lap belt, lap/shoulder belt, or the latch child restraint an- chorage system. • the belt-positioning booster seat is for children weigh- ing more than 40 lbs (18 kg), but who are still too small to fit in the vehicle’s seat belts properly. If the child ca...

  • Page 37

    Here are some tips on getting the most out of your child restraint: • before buying any restraint system, make sure that it has a label certifying that it meets all applicable safety standards. The manufacturer also recommends that you make sure that you can install the child restraint in the vehicl...

  • Page 38

    • buckle the child into the seat according to the child restraint manufacturer’s instructions. • when your child restraint is not in use, secure it with the seat belt or remove it from the vehicle. Do not leave it loose in the vehicle. In a sudden stop or collision, it could strike the occupants or ...

  • Page 39

    Note: when using the latch attaching system to install a child restraint, please ensure that all seat belts not being used for occupant restraints are stowed and out of reach of children. It is recommended that before installing the child restraint, buckle the seat belt so the seat belt is tucked be...

  • Page 40

    The rear seat lower anchorages are round bars, located at the rear of the seat cushion where it meets the seat back, and are just visible when you lean into the rear seat to install the child restraint. You will easily feel them if you run your finger along the intersection of the seatback and seat ...

  • Page 41

    Many, but not all restraint systems will be equipped with separate straps on each side, with each having a hook or connector for attachment to the lower anchorage and a means of adjusting the tension in the strap. Forward- facing toddler restraints and some rear-facing infant restraints will also be...

  • Page 42

    Installing child restraints using the vehicle seat belt the passenger seat belts are equipped with cinching latch plates, which are designed to keep the lap portion tight around the child restraint so that it is not necessary to use a locking clip. Pull up on the shoulder portion of the lap/shoulder...

  • Page 43

    Warning! An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchor positions directly behind the child seat to secure a child restraint top tether strap. Children too large for booster seats children who are large enough to wear th...

  • Page 44

    • check belt fit periodically. A child’s squirming or slouching can move the belt out of position. • if the shoulder belt contacts the child’s face or neck, move the child closer to the center of the vehicle. Never allow a child to put the shoulder belt under an arm or behind their back. Transportin...

  • Page 45

    A new engine may consume some oil during its first few thousand miles (kilometers) of operation. This should be considered as a normal part of the break-in and not interpreted as an indication of difficulty. Safety tips exhaust gas warning! Exhaust gases can injure or kill. They contain carbon monox...

  • Page 46

    • on hardtop models, keep the tailgate window closed when driving your vehicle. On fabric top models, do not drive with the rear window curtain up unless the side curtains are also open. This will prevent carbon monoxide and other poisonous exhaust gases from entering the vehicle. Safety checks you ...

  • Page 47

    Safety checks you should make outside the vehicle tires examine tires for excessive tread wear or uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread. Inspect for tread cuts or sidewall cracks. Check wheel nuts for tightness and tires (includ- ing spare) for pr...

  • Page 49: Contents

    Understanding the features of your vehicle contents 䡵 mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52 ▫ inside day/night mirror . . . . . . . . . . . . . . . . .52 ▫ inside automatic dimming compass/temperature mirror — if equipped . . . . . . . . . . . . . . . . . . .52 ▫ co...

  • Page 50

    ▫ parking lights, instrument panel lights, and headlights . . . . . . . . . . . . . . . . . . . . . . . . . . .64 ▫ lights-on reminder . . . . . . . . . . . . . . . . . . . .65 ▫ headlight dimmer switch . . . . . . . . . . . . . . . .65 ▫ passing light . . . . . . . . . . . . . . . . . . . . . . . ....

  • Page 51

    ▫ console storage compartment — if equipped . .74 ▫ add-a-trunk™ — if equipped . . . . . . . . . . . .74 䡵 dual top — if equipped . . . . . . . . . . . . . . . . . .75 ▫ removing the soft top . . . . . . . . . . . . . . . . . .75 ▫ installing the soft top . . . . . . . . . . . . . . . . . .77 䡵 hard...

  • Page 52

    Mirrors inside day/night mirror the mirror should be adjusted to center on the view through the rear window. A two-point pivot system allows for horizontal and vertical adjustment of the mirror. Annoying headlight glare can be reduced by moving the small control under the mirror to the night positio...

  • Page 53

    Note: in some long, low speed traffic situations, the displayed temperature readings will be higher than the actual ambient temperature. This is considered normal. Accurate readings will resume with vehicle speed and sensor airflow. Caution! To avoid damage to the mirror during cleaning, never spray...

  • Page 54

    Compass calibration automatic calibration once calibrated, the compass has the ability to self- correct for changes in magnetic field to keep the compass accurate. This is referred to as automatic calibration. If magnetic field changes are too great, the compass will enter cal mode on it’s own and m...

  • Page 55

    Compass variation adjustment compass variance is the difference between magnetic north and geographic north. In some areas of the country, the difference between magnetic and geographic north is great enough to cause the compass to give false readings. If this occurs, the compass variance must be se...

  • Page 56

    To set the variance: turn the ignition on, and press and hold the center button for 3 to 6 seconds. The last variance zone number will be displayed. Each press of the center button will select a new variance zone. When the proper zone is selected, wait 5 seconds to resume normal operation. Outside m...

  • Page 57

    Warning! • vehicles and other objects seen in the right side convex mirror will look smaller and farther away than they really are. Relying too much on your right side mirror could cause you to collide with another vehicle or other object. • use your inside mirror when judging the size or distance o...

  • Page 58

    Front seat adjustment move seat forward or rearward by lifting the lever. Be sure the latch engages fully. Front seat adjustment — recline to adjust seatback, lift lever, lean back, and release lever at desired position. To return seatback, lift the lever, lean forward and release the lever. Front s...

  • Page 59

    Warning! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt and be seriously or even fatally injured. Use the recliner only when the vehicle is parked. Tilting front seats push the lever upward ...

  • Page 60

    2. Lift the seatback release lever and fold seatback for- ward. 3. Slowly flip the entire seat forward. 4. When completed, return seat to it’s normal position. Rear seat release lever folding rear seat 60 understanding the features of your vehicle.

  • Page 61

    Removing the rear seat warning! • it is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision people riding in these areas are more likely to be seri- ously injured or killed. • do not allow people to ride in any area of your vehicle that is not equipped with se...

  • Page 62

    Replacing the rear seat reverse steps for removing the seat. Be certain to pull the seat belts between the seat cushion and seatback. Position them for passenger use. Warning! • to help protect against personal injury, passen- gers should not be seated in the rear cargo area with the rear seat folde...

  • Page 63

    Next, locate handle in middle of the front end of the hood. Insert hand into gap between hood and radiator support and lift up on handle to raise hood. You may have to push down slightly on hood before lifting up on handle. Insert the support rod into the slot in the radiator support. To close the h...

  • Page 64

    Lights interior lights the overhead light comes on when a door is opened. It may also be turned on by rotating the control for the dimmer switch on the muti-function control lever fully upward. The overhead light will automatically turn off in about 20 minutes if a door is left open or the dimmer co...

  • Page 65

    To change the brightness of the instrument panel lights, rotate the center portion of the muti-function control lever up or down. Note: if the driver’s door is left open, and the head- lights or parking lights are left on, the “high beam indicator light” will flash and a chime will sound. Lights-on ...

  • Page 66

    Front fog lights — if equipped the front fog light switch is in the multi-function control lever. To activate the front fog lights, turn on the parking or low beam headlights and pull out the end of the lever. Note: the fog lights will only operate with the parking lights or the headlights on low be...

  • Page 67

    Windshield wipers and washers caution! In cold weather, always turn off the wiper switch and allow the wipers to return to the park position before turning off the engine. If the wiper switch is left on and the wipers freeze to the windshield, damage to the wiper motor may occur when the vehicle is ...

  • Page 68

    Windshield washers to use the washer, pull the lever toward you and hold while spray is desired. If the lever is pulled while in the delay range, the wiper will operate for two wipe cycles after the lever is released, and then resume the intermit- tent interval previously selected. If the lever is p...

  • Page 69

    Warning! Tilting the steering column while the vehicle is moving is dangerous. Without a stable steering col- umn, you could lose control of the vehicle and have an accident. Adjust the column only while the ve- hicle is stopped. Be sure it is locked before driving. Electronic speed control when eng...

  • Page 70

    To set at a desired speed when the vehicle has reached the desired speed, press and release the set button. Release the accelerator and the vehicle will operate at the selected speed. To deactivate a soft tap on the brake pedal, normal braking, or pressing the cancel button will deactivate the speed...

  • Page 71

    Note: when driving uphill, at elevations above 2,000 ft. (610 meters), or when the vehicle is heavily loaded (especially when towing) the vehicle may slow below the set speed. (if the vehicle speed drops below 35 mph (56 km/h), the speed control will automatically disengage). If this happens, you ca...

  • Page 72

    Electrical outlet use with engine off warning! • many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.E. Cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or p...

  • Page 73

    The rear passengers have cup holders at the rear of the center console. Storage glove compartment to open the glove compartment, pull the latch up. Rear cup holders glove compartment understanding the features of your vehicle 73 3.

  • Page 74

    Console storage compartment — if equipped to unlock, insert key and turn. To open, press the latch button. Add-a-trunk™ — if equipped the factory-installed add-a-trunk™ option provides a secured compartment for parcels or equipment when the tailgate is closed and locked. To gain access to this compa...

  • Page 75

    Dual top — if equipped if your vehicle is equipped with a dual top, you must remove one of the tops from the vehicle. The soft top was installed at the factory for shipping purposes only. The soft top and the hard top are to be used indepen- dently. Removal is mandatory to prevent any possible wear ...

  • Page 76

    4. Using a rubber mallet, carefully tap the knuckles from the outside edge. This will disconnect the bow assembly from the pivot bracket. Remove the soft top from the vehicle and store in a clean, dry location. 5. Unzip the zipper on the sport bar cover to expose the pivot bracket. Remove the bracke...

  • Page 77

    6. Reinstall the hard top. Refer to “hard top installation” in this section. Installing the soft top note: the following procedures are for first time set up only. For future soft top procedures, refer to “soft top” in this section. 1. Locate and remove the following items prior to hard top removal:...

  • Page 78

    4. If the soft top has been removed, follow these steps to reinstall the soft top. If the soft top is on the vehicle, proceed to step #5. A. If the pivot brackets have been removed, unzip the sport bar cover and attach the pivot brackets and screws with a #t40 torx 威 head driver. Re-cover and re-zip...

  • Page 79

    5. Unsnap and remove the black boot cover. This cover should be discarded. It was intended as a protective cover for shipping only. Note: a visual instruction sheet is enclosed in the dual top wrap. 6. Open the tailgate. 7. Remove the tailgate bar (black bar with end caps) that is located in the sof...

  • Page 80

    11. Working from the rear of the vehicle with the tailgate open, lift the plastic header (with latches) up and over the sport bar. As the header reaches the top, locate the 2 bow and push it up and over the sport bar. 12. Move to the side of the vehicle and pull the side bow forward and down. You wi...

  • Page 81

    13. Unclip and move the sun visor to the side. 14. Open the header latches and engage the hooks on each side into the windshield slot. Note: do not latch at this time. Understanding the features of your vehicle 81 3.

  • Page 82

    15. Grasp the drip rail retainers and untuck them from the door frame. The soft top fabric should cover the header completely from one side to the other. This may require you to pull some of the fabric down and around the corners. Repeat this step for the other side. For unlimited models — pull the ...

  • Page 83

    16. Move to the rear of the vehicle and gently pull the sail panels over the 3 bow letting them hang down. Make sure the nylon check straps between the 2 bow and 3 bow are not twisted or wrapped around the 2 bow. Move to the rear of the vehicle and gently pull the rear corners (sail panels) over the...

  • Page 84

    For unlimited models — look up at the 3 bow and remove the four screws. Grasp the fabric rearward of the 3 bow, and pull it up and around, reinstalling all four screws through the existing fabric holes. (refer to the instruction sheet in the soft top for additional informa- tion and photos). 18. Ali...

  • Page 85

    Note: this may be difficult due to fabric tension. If difficulty is experienced with fabric tension, place your hand on top of the 3 bow and gently pull down to help tuck in the sail panels. 19. To install the quarter windows, affix the rear corner of the quarter window temporarily to the velcro 威. ...

  • Page 86

    20. Tuck in the bottom retainers on the quarter windows into the bodyside retainer, beginning from the rear and working to the front of the vehicle. Repeat this step for the other side. 21. Locate the black retainer bar that was set aside, and the rear window. Remove and discard the end caps. Slide ...

  • Page 87

    22. Zip the rear window beginning from the left using both zipper ends. Run the upper zipper around the window to the right side leaving the lower zipper end at the start on the left. 23. Tuck in the retainer bar ends into the tailgate clips on each side of the tailgate opening. Understanding the fe...

  • Page 88

    24. Tuck the lower retainers on both sides of the rear window under the tailgate clips. Reinstall the left sail panel if it was untucked to get the rear window zipper started. 25. Tuck the drip rail retainers into the door frame slots above the door on both sides. 88 understanding the features of yo...

  • Page 89

    26. Close the header latches and return the sun visor to it’s secure position. Hard top caution! • the hard top is not designed to carry any addi- tional loads such as roof racks, spare tires, build- ing, hunting, or camping supplies, and/or lug- gage, etc. Also, it was not designed as a structural ...

  • Page 90

    Caution! Do not move your vehicle until the top has been either fully attached to the windshield frame and bodyside, or fully removed. Hard top removal 1. Fold down the sun visors and move them to the side. 2. Unlatch the two hard top latches located at the top of the windshield. 3. Unbolt the six t...

  • Page 91

    Caution! When removing the 2 front screws just rearward of the doors, make sure that the nut does not fall into the seat belt retractor. Grasp the nut to prevent this from occurring. Note: on a dual top vehicle, the two rear and center nuts are retained onto the bodyside. 4. Open both doors. 5. Open...

  • Page 92

    6. Locate the wiring harness at the rear left side corner of the vehicle. 7. Disconnect the washer hose and install the tethered cap. Caution! Make sure storage cap is installed to prevent foreign materials from entering tube and clogging system. 92 understanding the features of your vehicle.

  • Page 93

    8. Disconnect the wire harness from the hard top by pressing the tab at the side of the connector and pulling to disconnect. Note: if the red latch on the connector is locked, push the red latch to the right until you can only see the latch on one end (right) of the connector. This will unlock conne...

  • Page 94

    Hard top installation note: if the door frames are installed from soft top usage, they must be removed prior to installation of the hard top. 1. Inspect the hard top seals for damage and replace if necessary. 2. Install the hard top using the same steps for removal in reverse order. Note: the hard t...

  • Page 95

    If the temperature is below 72°f (24°c) and/or the top has been folded down for a period of time, the top will appear to have shrunk when you raise it, making it difficult to put up. This is caused by a natural contraction of the vinyl coating on the fabric top. Place the vehicle in a warm area. Pul...

  • Page 96

    Warning! • do not drive vehicle with rear window curtain up unless side curtains are also open. Dangerous exhaust gases which can kill could enter the vehicle. • the fabric upper doors and fabric top are de- signed only for protection against the elements. Do not rely on them to contain occupants wi...

  • Page 97

    Note: stow half doors carefully outside of the vehicle, never inside to avoid scratches. 2. Grasp the fabric of the top above the door frame. Pull down and out on the fabric to untuck the drip rail retainers from the door frame slot. Start with the rear retainer and work forward towards the windshie...

  • Page 98

    5. Open the tailgate, partially unzip the rear window on each side, and untuck the lower retainers on the window from the tailgate clips on both sides of the tailgate opening. 6. Pull the retainer bar straight out from the tailgate clips. • remove the rear window entirely. This is done by unzipping ...

  • Page 99

    7. Beginning from the rear, moving forward, partially unzip the side window and untuck the bottom retainers. 8. Finish unzipping the window and untuck from the door frame retainer at the front of the window, repeat this step on the other side. Note: stow clean windows carefully outside of the vehicl...

  • Page 100

    10. Completely release the hooks on the rear side of the windshield. Grasp the side bow behind the header and lift top back. 11. As you begin to lower the top, wrap the sail panels so that they rest on the roof of the vehicle. Note: if your vehicle is equipped with a dual top, prevent connector dama...

  • Page 101

    Tuck the top material between the 2 bow and the 3 bow as it folds. 13. Tuck the top material between the 2 bow and the header. Understanding the features of your vehicle 101 3.

  • Page 102

    14. After the top is folded down, ensure that the drip rail retainers are tucked in inward as shown. This is to avoid unnecessary wear to the fabric. 15. After the top is folded down, tuck the check straps so that they are not hanging and flapping outside the vehicle. 102 understanding the features ...

  • Page 103

    Putting up the soft top note: be sure the wire harness is not attached to the soft top bows before you lift the top. 1. Begin working from the rear of the vehicle, with the tailgate open. Lift the plastic header (with latches) up and over the sport bar. As the header reaches the top, locate the 2 bo...

  • Page 104

    3. Unclip and move the sun visor to the side. 4. Open the header latches and engage the hook on each side into the windshield slot. 104 understanding the features of your vehicle.

  • Page 105

    5. Grasp the drip rail retainer and untuck them from the door frame. Note: do not tuck the drip rails into the door frame at this time. 6. Move to the rear of the vehicle and gently pull the sail panels over the 3 bow letting them hang down. Understanding the features of your vehicle 105 3.

  • Page 106

    7. Align the sail panel retainer to the edge of the bodys- ide retainer at the rear. Tuck the sail panel into the bodyside retainer beginning from the rear and working to the corner. Tuck the retainer around the corner and continue forward. Note: this may be difficult due to fabric tension. If diffi...

  • Page 107

    8. To install the quarter window, affix the rear corner of the window temporarily to the velcro 威. Start and zip the zipper only about 1 inch (2.5 cm). At this time it is necessary to tuck in the door frame retainer. 9. After the door frame retainer has been completely tucked in, finish zipping in t...

  • Page 108

    10. Tuck the bottom retainer of the quarter window into the bottom retainer, beginning from the rear and working to the front of the vehicle. Repeat this step for the other side. 11. To assist in getting the zipper started, lay the retainer bar inside the vehicle on the wheel wells and uninstall hal...

  • Page 109

    12. Zip in the rear window beginning from the left using both zipper ends. Run the upper zipper around the window leaving the lower zipper at the start. 13. Tuck the retainer bar into the tailgate clips. Understanding the features of your vehicle 109 3.

  • Page 110

    14. Tuck the lower retainers of the rear window under the tailgate clips. Reinstall the left corner if it was untucked to get the rear window zipper started. 15. Tuck the drip rail retainers into the door frame slot above the door on both sides. 110 understanding the features of your vehicle.

  • Page 111

    16. Close the header latches and return the sun visor to it’s secured position. Soft top — sunrider equipped models caution! • the soft top is not designed to carry any addi- tional loads such as roof racks, spare tires, build- ing, hunting, or camping supplies, and/or lug- gage, etc. Also, it was n...

  • Page 112

    Place the vehicle in a warm area. Pull steadily on the top fabric. The vinyl will stretch back to its original size and the top can then be snapped into place. If temperature is 41°f (5°c) or below, do not attempt to put the top down or roll the rear or side curtains. Caution! • do not run a fabric ...

  • Page 113

    Warning! • do not drive vehicle with rear window curtain up unless side curtains are also open. Dangerous exhaust gases which can kill could enter the vehicle. • the fabric upper doors and fabric top are de- signed only for protection against the elements. Do not rely on them to contain occupants wi...

  • Page 114

    1. Grasp the fabric of the top above the door frame. Pull down and out on the fabric to untuck the drip rail retainers from the door frame slot. Start at the back of the rear drip rail retainer and work forward towards the windshield. Repeat this on the other side. 2. Unclip and move the sun visors ...

  • Page 115

    5. Grip and rotate the retainer bar up towards you to release it from the upper portion of the tailgate clips. The retainer bar runs along the bottom of the rear window. 6. Remove the rear window entirely. This is done by unzipping the window, bringing both the right zipper and the left zipper tabs ...

  • Page 116

    8. Finish unzipping the window and untuck from the door frame retainer at the front of the window, repeat this step on the other side. Note: stow clean windows carefully outside of the vehicle to avoid scratches. 9. Untuck the sail panels from the rear corners of the vehicle. Note: if difficulty is ...

  • Page 117

    10. Release the sunrider pins to release the top bows from the brackets located on both door rails. Push up and back on the bow slightly so it does not fall back and lock into the brackets. 11. Grasp the side bow behind the header and lift the top back. Understanding the features of your vehicle 117...

  • Page 118

    12. As you begin to lower the top, wrap the sail panels so that they rest on the roof of the vehicle. 13. Make sure the sides of the top are folded inward as the top continues to fold, and check straps are clear of the vehicle. For unlimited models — tuck the top between the 2 bow and 2-1/2 bow and ...

  • Page 119

    14. Tuck the top material between the 2 bow and the header. 15. After the top is folded down, ensure that the drip rail retainers are tucked in inward as shown. This is to avoid unnecessary wear to the fabric. Understanding the features of your vehicle 119 3.

  • Page 120

    16. After the top is folded down, tuck the check straps inside the rear corners of the vehicle. This will keep them from hanging and flapping outside the vehicle. 17. Hook the header latches back onto the header to keep them from rattling. Putting up the soft top note: be sure the wire harness is no...

  • Page 121

    3. Begin working from the rear of the vehicle with the tailgate open. Standing to the side of the vehicle, lift the top by the 2 bow and 3 bow over the sport bar. 4. Engage the hooks on each side of the header into the windshield slots and fully engage the header latches. For wrangler models — you m...

  • Page 122

    5. Pull the side bow forward and down. Make certain the blocks on the side bows line up with the retainers on the door rails. Lock the blocks in place. Note: check to make certain the check straps are not tangled on any of the other top hardware. This will prevent the top from being put all the way ...

  • Page 123

    7. Tuck the sail panel retainer into the bodyside retainer. Begin working from the rear tailgate opening and work to the corner. Note: this may be difficult due to fabric tension. If difficulty is experienced with fabric tension, place your hand on top of the 3 bow and pull down to help tuck in the ...

  • Page 124

    8. To install the quarter windows, affix the upper rear corner of the window temporarily using the velcro 威. Next, start the zipper about 1 inch (2.5 cm) at the upper forward corner of the window. At this time it is necessary to tuck in the door frame retainer. 9. After the door frame retainer has b...

  • Page 125

    10. Tuck the bottom retainer on the quarter window into the bottom retainer, beginning from the rear and working to the front of the vehicle. Repeat this step for the other side. 11. Zip in the rear window beginning from the left using both zipper ends. Run the upper zipper around the window leaving...

  • Page 126

    Note: to assist in getting the zipper started, lay the bar inside the vehicle on the right wheel well, uninstall half of the left sail panel from the bodyside retainer, begin- ning near the tailgate open to expose zipper ends. 12. Tuck the retainer bar into the upper portion of the tailgate clips. 1...

  • Page 127

    14. Reinstall the corner of the sail panel that was un- tucked to get the rear window zipper started. 15. Tuck the drip rail retainers into the door frame slots above the door on both sides. Start at the front next to the windshield and work rearward. 16. Return the sun visors to their secure positi...

  • Page 128

    To raise 1. Grasp the drip rail retainers and untuck both of them starting at the rear of the door frame slot. Repeat this on the other side. 2. Unclip and move the sun visors to the side. 3. Release the header latches, and slide the plastic sleeves forward. 128 understanding the features of your ve...

  • Page 129

    4. Grasp the header and lift the top back. Make sure the material is folded back as shown. Secure latches to plastic retainer on header. 5. Locate strap to secure the header to the sport bar. Wrap strap around sport bar and hook to header and tighten. 6. Attach and reposition sun visors. Understandi...

  • Page 130

    To lower 1. Remove strap from header and sport bar. 2. Release header latches from header retainer. 3. Unclip and move the sun visors to the side. 4. Grasp the front header and pull to the front of the vehicle. 5. Slide plastic sleeve rearward over sunrider link. 6. Tuck drip rail retainers into the...

  • Page 131

    2. Fold the door frames and store the knobs and door frames outside of the vehicle. Repeat this step for the other side. Warning! • use both hands to remove the door frames. The door frames will fold and could cause injury if both hands are not used. • never store the door frames in your vehicle. In...

  • Page 132

    3. Slide door frame forward until the pin holes in the top line up with the holes in the side bar. Screw in the knobs and tighten, beginning with the front knob. Repeat procedures on the other side. Folding windshield the fold down windshield and removable side bars on your vehicle are structural el...

  • Page 133

    Do not drive your vehicle on-road with the windshield down and the side bars removed as you lose the protec- tion these structural elements can provide. Note: before lowering windshield, disconnect the elec- trical connector for the inside compass/temperature mirror (if equipped). Note: the windshie...

  • Page 134

    Warning! Carefully follow these warnings to help protect against personal injury: • do not drive your vehicle on-road with the windshield down. • do not drive your vehicle unless the windshield is securely fastened, either up or down. • eye protection, such as goggles, should be worn at all times wh...

  • Page 135

    3. Remove the two torx 威 head screws holding each side bar to the windshield frame. Shift the side bar inboard to clear windshield pillar molding when removing the side bar. Note: store all of the mounting bolts in their original threaded holes and tighten for safekeeping. 4. Unzip the sport bar pad...

  • Page 136

    Caution! Do not remove the head impact foam from the side bars, as damage to the foam may result. 5. To safely store the side bars in your vehicle, use four of the cinch straps, found in the glove box. Attach the straps through the footman loops located in the floor behind the folded rear seat on ea...

  • Page 137

    7. Remove the black round headed windshield torx 威 head screw on each side of the base of the windshield. 8. Lower the windshield gently until it contacts the rubber hood bumpers. Understanding the features of your vehicle 137 3.

  • Page 138

    9. Secure the windshield by passing the remaining cinch strap, found in the glove box, through the footman hoop on the center of the hood and on the center of the windshield frame. Tighten the strap to secure the wind- shield in place. Raising the windshield and replacing side bars to raise the wind...

  • Page 139

    Rear window features — hard top only rear window defogger to turn the rear window defogger on, press the rocker switch. If you press the switch a second time, you will turn the defogger off. A light on the rocker switch will indicate the defogger is on. The defogger will automatically turn off after...

  • Page 140

    Rear window wiper/washer to utilize the rear wiper, press the switch to the first detent. To activate the rear washer, depress the switch to the second detent. The washer will continue to spray as long as the switch is held. The switch will return to the wiper mode when released. To turn the rear wi...

  • Page 141

    Adding washer fluid the fluid reservoir for the windshield washers and the rear window washer is shared. It is located in the front of the engine compartment on the passenger side and should be checked for fluid level at regular intervals. Fill the reservoir with windshield washer solvent (not radia...

  • Page 143: Contents

    Understanding your instrument panel contents 䡵 instrument panel and interior controls . . . . . . . 145 䡵 instrument cluster . . . . . . . . . . . . . . . . . . . . . . 146 䡵 instrument cluster description . . . . . . . . . . . . . 147 䡵 electronic digital clock . . . . . . . . . . . . . . . . . . 1...

  • Page 144

    䡵 sales code rbq—am/fm stereo radio with 6 - disc cd changer . . . . . . . . . . . . . . . . . . . . . . . 160 ▫ radio operation . . . . . . . . . . . . . . . . . . . . . . 160 ▫ cd player operation . . . . . . . . . . . . . . . . . . . 163 䡵 satellite radio — if equipped . . . . . . . . . . . . . ....

  • Page 145

    Instrument panel and interior controls understanding your instrument panel 145 4.

  • Page 146

    Instrument cluster 146 understanding your instrument panel.

  • Page 147

    Instrument cluster description your vehicle is equipped with the instrument cluster described on the following pages. 1. Voltmeter indicates available battery voltage and charging system operation. The lower red zone indicates that battery charge may be too low to start the engine. With the engine r...

  • Page 148

    7. High beam indicator light this light shows that the headlights are on high beam. Pull the turn signal lever towards the steering wheel to switch the headlights from high or low. If the driver’s door is open, and the headlights or parklights are left on, the “high beam indicator light” will flash ...

  • Page 149

    13. Oil pressure gauge indicates engine oil pressure. This gauge does not indicate oil level, and pressure varies with engine speed, temperature and oil viscosity. Consistent lower readings indicate possible malfunction. Seek authorized service. 14. Coolant temperature gauge indicates engine coolant...

  • Page 150

    Certain conditions such as a loose or missing gas cap, poor quality fuel, etc. May illuminate the light after engine start. The vehicle should be serviced if the light stays on through several typical driving styles. In most situations, the vehicle will drive normally and will not require towing. Wh...

  • Page 151

    20. Anti-lock (abs) warning light after ignition is turned on, illuminates to indicate function check at vehicle start-up. If light remains on after start-up or comes on and stays on at road speeds, it may indicate that the abs has detected a malfunction or has become inoperative. The system reverts...

  • Page 152

    23. Fuel cap indicator this symbol indicates the side of the vehicle where the fuel cap is located. 24. Fuel gauge the pointer shows the level of fuel in the fuel tank. When the fuel gauge pointer initially moves to e, for your safety, approximately 2 u.S. Gallons (7.6l) of fuel remain. Note: when t...

  • Page 153

    Radio general information radio broadcast signals your new radio will provide excellent reception under most operating conditions. Like any system, however, car radios have performance limitations, due to mobile op- eration and natural phenomena, which might lead you to believe your sound system is ...

  • Page 154

    Note: on vehicles so equipped the radio, steering wheel radio controls and 6 disc cd/dvd changer will remain active for up to 45 seconds after the ignition switch has been turned off. Opening a vehicle front door will cancel this feature. Sales code rbk—am/ fm stereo radio with cd player and cd chan...

  • Page 155

    Note: power to operate the radio is supplied through the ignition switch. It must be in the on or acc position to operate the radio. Seek press and release the seek button to search for the next station in either the am or fm mode. Press the top of the button to seek up or the bottom to seek down. T...

  • Page 156

    Audio the audio button controls the bass, treble, bal- ance, and fade. Press the audio button and bass will be displayed. Press the seek + or seek – to increase or decrease the bass tones. Press the audio button a second time and treb will be displayed. Press the seek + or seek – to increase or decr...

  • Page 157

    Note: changes or modifications not expressively ap- proved by the party responsible for compliance could void the user’s authority to operate the equipment. Cd player operation note: the ignition switch must be in the on or acc position and the volume control on before the cd player will operate. In...

  • Page 158

    If you do not remove the disc within 15 seconds, it will be reloaded. The unit will continue in radio mode. The disc can be ejected with the radio and ignition off (except on convertibles). Ff/tune/rw press ff (fast forward) and the cd player will begin to fast forward until ff is released. The rw (...

  • Page 159

    Mode button to activate the cd changer, press the mode button until cd information appears on the display. Disc up/program button 1 press the disc up (button 1) button to play the next available disc. Disc down/program button 5 press the disc down (button 5) button to play the previous disc. Seek bu...

  • Page 160

    Cd hot will pause the operation. Play can be resumed when the operating temperature is corrected or another mode is selected. An err symbol will appear on the display if the laser is unable to read the disc data for the following reasons: • excessive vibration • disc inserted upside down • damaged d...

  • Page 161

    Note: power to operate the radio is controlled by the ignition switch. It must be in the on or acc position to operate the radio. Mode press the mode button repeatedly to select between am, fm, the cd changer and sirius satellite radio™ (if equipped). The display will show st when a stereo station i...

  • Page 162

    And release that button. If a button is not selected within 5 seconds after pressing the set rnd button, the station will continue to play but will not be locked into push- button memory. You may add a second station to each push-button by repeating the above procedure with this exception: press the...

  • Page 163

    General information this radio complies with part 15 of fcc rules and with rss-210 of industry canada. Operation is subject to the following conditions: 1. This device may not cause harmful interference, 2. This device must accept any interference received, including interference that may cause unde...

  • Page 164

    Show the disc number, the track number, and index time in minutes and seconds. Play will begin at the start of track 1. Load/ ejt — load press the load/ ejt button and the button with the corresponding number where the cd is being loaded. After the radio displays “load” insert the cd into the player...

  • Page 165

    Ff/tune/rw press ff (fast forward) and the cd player will begin to fast forward until ff is released. The rw ( reverse) button works in a similar manner. Random play — set / rnd press the rnd button while the cd is playing to activate random play. This feature plays the tracks on the disc in random ...

  • Page 166

    Program type radio display nostalgia nostalga oldies oldies personality persnlty public public rhythm and blues r & b religious music rel musc religious talk rel talk rock rock soft soft soft rock soft rck soft rhythm and blues soft r&b sports sports talk talk top 40 top 40 weather weather by pressi...

  • Page 167

    Time press the time button to change the display from elapsed cd playing time to time of day. Operating instructions - satellite radio mode (if equipped) refer to the satellite radio section of the owner’s manual. Cd diagnostic indicators when driving over a very rough road, the cd player may skip m...

  • Page 168

    System activation to activate your sirius satellite radio service, call the toll-free number 888-539-7474, or visit the sirius web site at www.Sirius.Com. Please have the following informa- tion available when activating your system: 1. The electronic serial number/sirius identification number (esn/...

  • Page 169

    Mode when any other button is pushed, the ignition is turned off, or 5 minutes has passed since any button was pushed. Selecting satellite mode in rbb, rah and rbk radios press the mode button repeatedly until ⬙s a⬙ appears in the display. A cd or tape may remain in the radio while in the satellite ...

  • Page 170

    Note: channels that may contain objectionable content can be blocked. Contact sirius customer care at 888-539- 7474 to discuss options for channel blocking or unblock- ing. Please have your esn/sid information available. Storing and selecting pre-set channels in addition to the 10 am and 10 fm pre-s...

  • Page 171

    Satellite antenna to ensure optimum reception, do not place items on the roof around the rooftop antenna location. Metal objects placed within the line of sight of the antenna will cause decreased performance. Larger luggage items should be placed as far forward as possible. Do not place items direc...

  • Page 172

    Radio operation and cellular phones under certain conditions, the cellular phone being on in your vehicle can cause erratic or noisy performance from your radio. This condition may be lessened or eliminated by relocating the cellular phone antenna. This condition is not harmful to the radio. If your...

  • Page 173

    Blower switch the blower switch is the rotary knob to the left of the controls. The blower speed will increase as the knob is turned clockwise. There are four blower speeds. Note: the blower motor will run until the mode control knob is turned to the “off” (“o”) position or the ignition is turned of...

  • Page 174

    Bi-level outside air comes from both instrument panel and floor outlets. Also, a slight amount of airflow may be noticed at the defrost outlet located at the base of the windshield. Floor outside air comes from the floor outlets. Also, a slight amount of airflow may be noticed at the defrost outlet ...

  • Page 175

    You can choose your degree of comfort by rotating the knob. The coldest setting is to the extreme left (blue region) and the warmest setting is to the extreme right (red region). Mode selection the mode selector is the right knob located on the climate controls. It can be set in any of the following...

  • Page 176

    Off turning the rotary knob to this position shuts off the blower motor and outside air will not come through any outlet. Recirculation select this position when the outside air contains smoke, odors, high humidity, or if rapid cooling is desired. This feature allows for recirculation of interior ai...

  • Page 177

    Mix outside air comes from the floor and defrost out- lets. This mode works best in cold or snowy con- ditions. It allows you to stay comfortable while keeping the windshield clear. Defrost outside air comes from the windshield outlets with a small amount being directed through the floor outlets. Us...

  • Page 178

    Window fogging in mild but rainy or humid weather, the windows might fog on the inside. To clear the fog off all of the windows, turn the mode control knob to the “panel” position (with snowflake). Adjust the temperature control and blower speed to maintain comfort. Direct the panel outlets toward t...

  • Page 179: Starting And Operating

    Starting and operating contents 䡵 starting procedures . . . . . . . . . . . . . . . . . . . . . 182 ▫ manual transmission . . . . . . . . . . . . . . . . . . 182 ▫ automatic transmission . . . . . . . . . . . . . . . . 182 ▫ normal starting . . . . . . . . . . . . . . . . . . . . . . 182 ▫ extreme c...

  • Page 180

    䡵 axle lock (tru–lok™) — if equipped . . . . . . . . 199 䡵 parking brake . . . . . . . . . . . . . . . . . . . . . . . . . 200 䡵 about your brakes . . . . . . . . . . . . . . . . . . . . . . 203 䡵 anti-lock brake system — if equipped . . . . . . . 205 䡵 power steering . . . . . . . . . . . . . . . ....

  • Page 181

    䡵 tire chains . . . . . . . . . . . . . . . . . . . . . . . . . . . 228 䡵 tire rotation recommendations . . . . . . . . . . . . 228 䡵 fuel requirements . . . . . . . . . . . . . . . . . . . . . . 229 ▫ reformulated gasoline . . . . . . . . . . . . . . . . . 230 ▫ gasoline/oxygenate blends . . . . . ...

  • Page 182

    Starting procedures before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. Warning! Do not leave children or animals inside parked vehicles in hot weather. Interior heat build up may cause serious injury or death. Manual transmission apply...

  • Page 183

    10 seconds, turn the key to the off position, wait 5 seconds, then repeat the normal starting procedure. Extreme cold weather (below –20°f or –29°c) to insure reliable starting at these temperatures, use of an externally powered electric engine block heater (available from your dealer) is recommende...

  • Page 184

    If the engine has been flooded, it may start to run, but not have enough power to continue running when the key is released. If this occurs, continue cranking with the accel- erator pedal pushed all the way to the floor. Release the accelerator pedal and the key once the engine is running smoothly. ...

  • Page 185

    Warning! Remember to disconnect the cord before driving. Damage to the 110-115 volt ac electrical cord could cause electrocution. Use the heater when temperatures below 0°f (-18°c) are expected to last for several days. Transmission shifting 6-speed manual transmission follow the shift pattern on th...

  • Page 186

    Warning! When parking your vehicle, always leave a manual transmission in first gear and apply the parking brake fully to guard against vehicle movement and possible injury or damage. Never use any gear as a substitute for the parking brake. Caution! To drive as safely as possible and to prolong the...

  • Page 187

    • when “rocking” a stuck vehicle by shifting between a forward gear and reverse, do not spin wheels faster than 15 mph (24 km/h), or drivetrain damage may result. Recommended manual transmission shifting speeds manual transmission shift speeds in mph (km/h) engine speeds 1 to 2 2 to 3 3 to 4 4 to 5 ...

  • Page 188

    3. Be sure to re-engage the clutch interlock safety feature by following these steps in reverse order when you are finished off-road driving. Automatic transmission shifting from d (drive) to p (park) or r (reverse) (or from p or r to d) should be done only after the accelerator pedal is released an...

  • Page 189

    Warning! It is dangerous to shift the selector lever out of “p” or “n” if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in re- verse. You could lose control of the vehicle and hit someone or something. Only ...

  • Page 190

    Warning! Unintended movement of a vehicle could injure those in and near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, you should always shift the vehicle into p (park), remove the key from the ignition, and apply the parkin...

  • Page 191

    R (reverse) for moving the vehicle rearward. Always stop before moving the lever to r (reverse), except when rocking the vehicle. N (neutral) engine may be started in this position. Note: towing the vehicle, coasting, or otherwise driv- ing with the transmission in n (neutral) can cause severe damag...

  • Page 192

    When frequent transmission shifting occurs while using overdrive, such as when operating the vehicle under heavy load conditions (for example, in hilly terrain, strong head winds, or trailer towing), turning off over- drive will improve performance and extend transmission life by reducing excessive ...

  • Page 193

    Warning! Never use p (park) position with an automatic trans- mission as a substitute for the parking brake. Al- ways apply parking brake fully when parked to guard against vehicle movement and possible injury or damage. Caution! • before moving the shift lever out of p (park), you must turn the ign...

  • Page 194

    Note: the transmission electronics constantly monitor the transmission oil temperature. If the transmission gets too hot, the transmission will change the way it shifts to help control the condition. This may result in a slightly different feeling or response during normal operation in d (drive) pos...

  • Page 195

    Operating instructions/precautions the transfer case provides four mode positions — two (rear) wheel drive high range, four wheel drive high range, neutral, and four wheel drive low range. This transfer case is intended to be driven in the two wheel drive (2h) position for normal street and highway ...

  • Page 196

    Proper operation of four wheel drive vehicles depends on tires of equal size, type, and circumference on each wheel. Any difference will adversely affect shifting and cause damage to the transfer case. Because four wheel drive provides improved traction, there is a tendency to exceed safe turning an...

  • Page 197

    4h position four wheel drive high range — locks the front and rear driveshafts together. Forces the front and rear wheels to rotate at the same speed. Additional traction for loose, slippery road surfaces. Note: this range should not be used during dry pavement operation. N (neutral) position neutra...

  • Page 198

    Is coasting at 2 to 3 mph (3 to 5 km/h), shift the transfer case lever firmly to the desired position. Do not pause in transfer case n (neutral). Note: pausing in transfer case n (neutral) in vehicles equipped with an automatic transmission may require shutting the engine off to avoid gear clash whi...

  • Page 199

    Slight application of the accelerator will supply maxi- mum traction. When starting with only one rear wheel on an excessively slippery surface, slight application of the parking brake may be necessary to gain maximum trac- tion. Warning! On vehicles equipped with a limited-slip differen- tial, neve...

  • Page 200

    • vehicle speed should be 10 mph (16 km/h) or less. To activate the system, press the switch once to lock the rear axle only (the rear lock indicator light will illuminate), press the switch again to lock the front axle (the front lock indicator light will illuminate). Once the rear axle is locked, ...

  • Page 201

    If the parking brake is not completely released, the brake warning light will remain on. Note: your vehicle has automatically adjusting rear brakes and we do not recommend any adjustment other than the maintenance performed by your authorized dealer. Before leaving the vehicle parked on a hill, you ...

  • Page 202

    Warning! • always fully apply the parking brake when leav- ing your vehicle, or vehicle may roll and cause damage or injury. Also be certain to leave a automatic transmission in p (park), or a manual transmission in 1st gear. Make certain the transfer case is in gear. Failure to do so may cause the ...

  • Page 203

    About your brakes your vehicle is equipped with power assisted brakes as standard equipment. In the event power assist is lost for any reason (for example, repeated brake applications with the engine off), the brakes will still function. The effort required to brake the vehicle will be much greater ...

  • Page 204

    Warning! To use your brakes and decelerate more safely, follow these tips: • do not “ride” the brakes by resting your foot on the pedal. This could overheat the brakes and result in unpredictable braking action, longer stopping distances, or brake damage. • when descending mountains or hills, repeat...

  • Page 205

    Warning! To help avoid personal injury, follow these tips: • never reach through the steering wheel to operate steering column controls. Injury to your hands or loss of vehicle control may result. • if the engine stalls or power assist fails due to a malfunction, vehicle steering and braking will re...

  • Page 206

    The anti-lock brake system pump motor runs during the self-test and during an abs stop to provide the regulated hydraulic pressure. The motor pump makes a low humming noise during operation, this is normal. During off-road use, loss of traction can temporarily defeat the system and cause the warning...

  • Page 207

    Caution! The anti-lock brake system is subject to possible detrimental effects of electronic interference caused by improperly installed aftermarket radios or tele- phones. Note: during severe braking conditions, a pulsing sensation may occur and a clicking noise will be heard. This is normal, indic...

  • Page 208

    Warning! Continued operation with reduced power steering assist could pose a safety risk to yourself and others. Service should be obtained as soon as possible. Caution! Prolong operation of the steering system at the end of the steering wheel travel will increase the steering fluid temperature and ...

  • Page 209

    Off-road driving tips when to use 4l (low) range when off-road driving, shift to 4l (low) for additional traction and control on slippery or difficult terrain, ascending or descending steep hills, and to increase low speed pulling power. This range should be limited to extreme situations such as dee...

  • Page 210

    And/or the flow rate is reduced. If you must cross flowing water avoid depths in excess of 9 inches. The flowing water can erode the streambed causing your vehicle to sink into deeper water. Determine exit point(s) that are downstream of your entry point to allow for drifting. Standing water avoid d...

  • Page 211

    If you stall or begin to lose headway while climbing a steep hill, allow your vehicle to come to a stop and immediately apply the brakes. Restart the engine and shift to r (reverse). Back slowly down the hill allowing the compression braking of the engine to help regulate your speed. If the brakes a...

  • Page 212

    After driving off-road off-road operation puts more stress on your vehicle than does most on-road driving. After going off-road it is always a good idea to check for damage. That way you can get any problems taken care of right away and have your vehicle ready when you need it. • completely inspect ...

  • Page 213

    Tire safety information tire markings note: • p(passenger)-metric tire sizing is based on u.S. Design standards. P-metric tires have the letter “p” molded into the sidewall preceding the size designation. Ex- ample: p215/65r15 95h. • european metric tire sizing is based on european design standards....

  • Page 214

    Tire sizing chart example: size designation: p = passenger car tire size based on u.S. Design standards ⴖ....Blank....ⴖ = passenger car tire based on european design standards lt = light truck tire based on u.S. Design standards t = temporary spare tire 31 = overall diameter in inches (in) 215 = sec...

  • Page 215

    Example: service description: 95 = load index —a numerical code associated with the maximum load a tire can carry. H = speed symbol —a symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions. —the maximum speed corresp...

  • Page 216

    Tire identification number (tin) the tin may be found on one or both sides of the tire however the date code may only be on one side. Tires with white sidewalls will have the full tin including date code located on the white sidewall side of the tire. Look for the tin on the outboard side of black s...

  • Page 217

    Tire loading and tire pressure tire placard location note: the proper cold tire inflation pressures are listed on the lower front inside corner of the driver door opening. Tire and loading information placard this placard tells you important information about the, 1) number of people that can be car...

  • Page 218

    3) the tire size designed for your vehicle 4) the cold tire inflation pressures for the front, rear and spare tires. Loading the vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adher...

  • Page 219

    4. The resulting figure equals the available amount of cargo and luggage load capacity. For example, if “xxx” amount equals 1400 lbs. And there will be five 150 lb. Passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lb. (since 5 x 150 = 750, and 1400 – 750 = 6...

  • Page 220

    220 starting and operating.

  • Page 221

    Warning! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. Tires — general information tire pressure proper tire inflation pressur...

  • Page 222

    2. Economy— improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Under inflation also increases tire rolling resistance and results in higher fuel consump- t...

  • Page 223

    Caution! After inspecting or adjusting the tire pressure al- ways reinstall the valve stem cap–if equipped. This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Inflation pressures specified on the placard are always “cold tire inflation pressure”. Col...

  • Page 224

    Tire pressures for high speed operation the manufacturer advocates driving at safe speeds within posted speed limits. Where speed limits or condi- tions are such that the vehicle can be driven at high speeds, maintaining correct tire inflation pressure is very important. Increased tire pressure and ...

  • Page 225

    Warning! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause tire dam- age or failure. A tire could explode and injure someone. Do not spin your vehicle’s wheels faster than 35 mph (55 km/h) when you are stuck, and do not let anyone near a spinning wheel no m...

  • Page 226

    Life of tire the service life of a tire is dependent upon varying factors including but not limited to: • driving style • tire pressure • distance driven warning! Tires and spare tire should be replaced after six years, regardless of the remaining tread. Failure to follow this warning can result in ...

  • Page 227

    Warning! • do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of un- approved tires and wheels may change suspension dimensions and performance characteristics, resulting in changes to steering, handling, and braking of your vehicle. This can cause ...

  • Page 228

    Tires may also cause the vehicle to pull left or right. Alignment will not correct this problem. See your autho- rized dealer for proper diagnosis. Improper alignment will not cause vehicle vibration. Vibration may be a result of tire and wheel out-of- balance. Proper balancing will reduce vibration...

  • Page 229

    These effects can be reduced by timely rotation of tires. The benefits of rotation are especially worthwhile with aggressive tread designs such as those on on/off road type tires. Rotation will increase tread life, help to main- tain mud, snow, and wet traction levels, and contribute to a smooth, qu...

  • Page 230

    Premium gasoline will provide no benefit over high quality regular gasoline, and in some circumstances may result in poorer performance. Light spark knock at low engine speeds is not harmful to your engine. However, continued heavy spark knock at high speeds can cause damage and immediate service is...

  • Page 231

    Caution! Do not use gasoline containing methanol. Gasoline containing methanol may damage critical fuel system components. Mmt in gasoline mmt is a manganese containing metallic additive that is blended into some gasoline to increase octane. Gasoline blended with mmt provides no performance advantag...

  • Page 232

    Fuel system cautions caution! Follow these guidelines to maintain your vehicle’s performance: • the use of leaded gas is prohibited by federal law. Using leaded gasoline can impair engine performance, damage the emission control system. • an out-of-tune engine, or certain fuel or ignition malfunctio...

  • Page 233

    Engine running for an extended period. If the vehicle is stopped in an open area with the engine running for more than a short period, adjust the ventilation system to force fresh, outside air into the vehicle. • guard against carbon monoxide with proper mainte- nance. Have the exhaust system inspec...

  • Page 234

    Caution! Damage to the fuel system or emission control system could result from using an improper fuel cap (gas cap). A poorly fitting cap could let impurities into the fuel system. Also, a poorly fitting after- market cap can cause the mil (malfunction indica- tor light) to illuminate, due to fuel ...

  • Page 235

    Warning! • remove the fuel cap (gas cap) slowly to prevent fuel spray from the filler neck which may cause injury. • the volatility of some gasoline may cause a buildup of pressure in the fuel tank that may increase while you drive. This pressure can result in a spray of gasoline and/or vapors when ...

  • Page 236

    • make sure that the fuel cap tether strap is not caught under the fuel cap. • be sure to remove the key. Caution! To avoid fuel spillage and overfilling, do not “top off” the fuel tank after filling. Note: when the fuel nozzle “clicks” or shuts off, the fuel tank is full. Trailer towing in this sec...

  • Page 237

    Gross trailer weight (gtw) the gross trailer weight (gtw) is the weight of the trailer plus the weight of all cargo, consumables and equipment (permanent or temporary) loaded in or on the trailer in its ⬙loaded and ready for operation⬙ condition. The recom- mended way to measure gtw is to put your f...

  • Page 238

    Frontal area the maximum height and maximum width of the front of a trailer. Trailer sway control the trailer sway control is a telescoping link that can be installed between the hitch receiver and the trailer tongue that typically provides adjustable friction associated with the telescoping motion ...

  • Page 239

    Refer to the trailer towing weights (maximum trailer weight ratings) chart for the max. Gtw towable for your given drivetrain. Trailer hitch classification class max. Gtw (gross trailer wt.) class i - light duty 2,000 lbs (907 kg) class ii - medium duty 3,500 lbs (1 587 kg) class iii - heavy duty 5,...

  • Page 240

    Engine/ transmis- sion model gvwr (gross vehicle wt. Rat- ing) gcwr (gross combined wt. Rating) frontal area max. Gtw (gross trailer wt.) max. Tongue wt. (see note 1) 2.4l/ manual 4,350 lbs (1 973 kg) 5,350 lbs (2 427 kg) 25 sq. Ft. (2.32 square meters) 1,000 lbs (453 kg) 100 lbs (45 kg) 4.0l/all 4,...

  • Page 241

    Which will cause loss of control of vehicle and trailer. Failure to load trailers heavier in front is the cause of many trailer accidents. Never exceed the maximum tongue weight stamped on your bumper or trailer hitch. Consider the following items when computing the weight on the rear axle of the ve...

  • Page 242

    Towing requirements to promote proper break-in of your new vehicle drivetrain components the following guidelines are recommended: note: trailer towing requires special rear axle lubri- cant. Refer to “fluids, lubricants, and genuine parts” in section 7 for more information. Caution! • avoid towing ...

  • Page 243

    • safety chains must always be used between your vehicle and trailer. Always connect the chains to the frame or hook retainers of the vehicle hitch. Cross the chains under the trailer tongue and allow enough slack for turning corners. • vehicles with trailers should not be parked on a grade. When pa...

  • Page 244

    Towing requirements — tires − do not attempt to tow a trailer while using a compact spare tire. − proper tire inflation pressures are essential to the safe and satisfactory operation of your vehicle. Refer to the tires–general information section of this manual on tire pressures for proper tire infl...

  • Page 245

    Caution! If the trailer weighs more than 1,000 lbs (454 kg) loaded, it should have its own brakes and they should be of adequate capacity. Failure to do this could lead to accelerated brake lining wear, higher brake pedal effort, and longer stopping distances. Warning! Do not connect trailer brakes ...

  • Page 246

    Note: do not cut or splice wiring into the vehicles wiring harness. The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector. Refer to the following illustrations. Towing tips before setting out on a trip, practice turning, stopping and backing ...

  • Page 247

    If using a manual transmission vehicle for trailer towing, all starts must be in first gear to avoid excessive clutch slippage. Towing tips — automatic transmission the “d” range can be selected when towing. However, if frequent shifting occurs while in this range, the “3” range should be selected. ...

  • Page 248

    Towing tips — cooling system to reduce potential for engine and transmission over- heating, take the following actions: − city driving when stopped for short periods of time, put transmission in neutral and increase engine idle speed. − highway driving reduce speed. − air conditioning turn off tempo...

  • Page 249

    Caution! It is necessary to follow these steps to be certain that the transfer case is fully in n (neutral) before recreational towing to prevent damage to internal parts. 1. Depress brake pedal. 2. Shift automatic transmission into n (neutral) or de- press clutch pedal on manual transmission. 3. Sh...

  • Page 250

    Shifting out of neutral (n) use the following procedure to prepare your vehicle for normal usage. 1. Shift automatic transmission into n (neutral) or de- press clutch pedal on manual transmission. 2. Shift transfer case lever into desired position. 3. Shift automatic transmission into d (drive) or r...

  • Page 251: Contents

    What to do in emergencies contents 䡵 hazard warning flasher . . . . . . . . . . . . . . . . . . 252 䡵 if your engine overheats . . . . . . . . . . . . . . . . . 253 䡵 jacking and tire changing . . . . . . . . . . . . . . . . 254 ▫ jack location . . . . . . . . . . . . . . . . . . . . . . . . 255 ▫ s...

  • Page 252

    Hazard warning flasher the flasher switch is on top of the steering column, just behind the steering wheel. Depress the switch and both cluster indicators and all front and rear directional sig- nals will flash. Depress the switch again to turn hazard warning flashers off. Hazard flasher switch 252 ...

  • Page 253

    Do not use this emergency warning system when the vehicle is in motion. Use it when your vehicle is disabled and is creating a safety hazard for other motorists. If it is necessary to leave the vehicle to go for service, the flasher system will continue to operate with the ignition key removed and t...

  • Page 254

    Caution! Driving with a hot cooling system could damage your vehicle. If the temperature gauge reads “h”, pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on the “h”, and you hear continuou...

  • Page 255

    Jack location the jack and lug wrench are stored under the front passenger seat. The jack handle driver and jack extension are located in a kit that is stored on the floor board to the right of the front passenger seat. On some models, this tool kit is under the carpeting in the same location. To re...

  • Page 256

    Note: if you have added aftermarket accessories to the spare tire mounted carrier, it cannot exceed a gross weight of 50 lbs (23 kg) including the weight of the spare tire. Preparations for jacking park on a firm level surface, avoid ice or slippery areas, set the parking brake and place automatic t...

  • Page 257

    4. Operate jack from the front or the rear of the vehicle. Place the jack under the axle tube, as shown. Do not raise the vehicle until you are sure the jack is fully engaged. 5. Raise the vehicle by turning the jack screw to the right. Raise the vehicle only until the tire just clears the surface a...

  • Page 258

    9. Finish tightening the lug nuts. Push down on the wrench while tightening for increased leverage. Alternate nuts until each nut has been tightened twice. Correct wheel nut tightness is 130 n·m (95 ft. Lbs). If in doubt about the correct tightness, have them checked with a torque wrench by your aut...

  • Page 259

    Set the parking brake, place an automatic transmission in p (park) (or n (neutral) for a manual transmission). Turn off lights, heater, and other electrical loads. Observe charge indicator in the battery. If indicator is light or yellow, replace the battery. Caution! Use the “jump starting” procedur...

  • Page 260

    Warning! • do not connect the cable to the negative terminal of the discharged battery. The resulting electrical spark could cause the battery to explode. • during cold weather when temperatures are be- low freezing point, electrolyte in a discharged battery may freeze. Do not attempt jump starting ...

  • Page 261

    Warning! Any procedure other than above could result in: • personal injury caused by electrolyte squirting out the battery vent. • personal injury or property damage due to battery explosion. • damage to charging system of booster vehicle or of immobilized vehicle. Towing a disabled vehicle the manu...

  • Page 263: Maintaining Your Vehicle

    Maintaining your vehicle contents 䡵 2.4l engine . . . . . . . . . . . . . . . . . . . . . . . . . . . 266 䡵 4.0l engine . . . . . . . . . . . . . . . . . . . . . . . . . . . 267 䡵 onboard diagnostic system — obd ii . . . . . . . . 268 䡵 emissions inspection and maintenance programs . . . . . . . . ....

  • Page 264

    ▫ air conditioner maintenance . . . . . . . . . . . . . 280 ▫ power steering fluid check . . . . . . . . . . . . . . 281 ▫ driveline and steering component lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . 282 ▫ body lubrication . . . . . . . . . . . . . . . . . . . . . 282 ▫ windshiel...

  • Page 265

    ▫ front side marker . . . . . . . . . . . . . . . . . . . . . 311 ▫ front fog light . . . . . . . . . . . . . . . . . . . . . . 311 ▫ rear tail, stop, turn signal, and back-up lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 313 ▫ center high mounted stop light (chmsl) . . . 313 䡵 fl...

  • Page 266

    2.4l engine 266 maintaining your vehicle.

  • Page 267

    4.0l engine maintaining your vehicle 267 7.

  • Page 268

    Onboard diagnostic system — obd ii your vehicle is equipped with a sophisticated onboard diagnostic system called obd ii. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide ex...

  • Page 269

    Emissions inspection and maintenance programs in some localities, it may be a legal requirement to pass an inspection of your vehicle’s emissions control system. Failure to pass could prevent vehicle registration. For states which have an i/m (inspection and maintenance) requirement, this check veri...

  • Page 270

    Ignition key or start the engine. This means that your vehicle’s obd system is not ready and you should not proceed to the i/m station. B. The mil will not flash at all and will remain fully illuminated until you turn off the ignition key or start the engine. This means that your vehicle’s obd syste...

  • Page 271

    Note: intentional tampering with emissions control systems can result in civil penalties being assessed against you. Warning! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the proper equipment. If you have any doubt abou...

  • Page 272

    The best time to check the engine oil level is about 5 minutes after a fully warmed engine is shut off, or before starting the engine after it has sat overnight. Checking the oil while the vehicle is on level ground will improve the accuracy of the oil level readings. Maintain the oil level between ...

  • Page 273

    • more than 50% of your driving is at sustained high speeds during hot weather, above 90°f (32°c) • taxi, police, or delivery service (commercial service) • trailer towing • off-road or desert driving • if equipped for and operating with e–85 (ethanol) fuel if any of these apply to you, then change ...

  • Page 274

    Engine oil viscosity (2.4l engines) sae 5w-30 engine oil is recommended for all operating temperatures. This engine oil improves low tempera- ture starting and vehicle fuel economy. Your engine oil filler cap shows the recommended engine oil viscosity for your vehicle. Engine oil viscosity (4.0l eng...

  • Page 275

    Engine oil filter selection all of the manufacturer’s engines have a full-flow type disposable oil filter. Use a filter of this type for replace- ment. The quality of replacement filters varies consider- ably. Only high quality filters should be used to assure most efficient service. Mopar 威 engine ...

  • Page 276

    Under normal operating conditions, the catalytic con- verter will not require maintenance. However, it is im- portant to keep the engine properly tuned to assure proper catalyst operation and prevent possible catalyst damage. Caution! Damage to the catalytic converter can result if your vehicle is n...

  • Page 277

    To minimize the possibility of catalytic converter dam- age: • do not shut off the engine or interrupt the ignition when the transmission is in gear and the vehicle is in motion. • do not try to start the engine by pushing or towing the vehicle. • do not idle the engine with any spark plug wires dis...

  • Page 278

    Fuel filter a plugged fuel filter can cause hard starting or limit the speed at which a vehicle can be driven. Should an excessive amount of dirt accumulate in the fuel tank, frequent replacement of the fuel filter which is mounted in the fuel tank may be necessary. Engine air cleaner filter under n...

  • Page 279

    Warning! Battery posts, terminals, and related accessories con- tain lead and lead compounds. Always wash hands after handling the battery. To determine the battery charge, check the battery test indicator (if equipped) on top of the battery. Refer to the illustration. Caution! It is essential when ...

  • Page 280

    Air conditioner maintenance for best possible performance, your air conditioner should be checked and serviced by an authorized dealer at the start of each warm season. This service should include cleaning of the condenser fins and a performance test. Drive belt tension should also be checked at thi...

  • Page 281

    Refrigerant recovery and recycling r-134a air conditioning refrigerant is a hydrofluorocar- bon (hfc) that is endorsed by the environmental pro- tection agency and is an ozone-saving product. How- ever, the manufacturer recommends that air conditioning service be performed by dealers or other servic...

  • Page 282

    Driveline and steering component lubrication u-joints (cardan joints) are sealed and do not require lubrication. Prop shafts, yokes, ball joints and other driveline and steering components may be provided with grease fittings for lubrication. Lubrication of these com- ponents at the intervals specif...

  • Page 283

    Remove frost or ice from the windshield. Keep the blade rubber out of contact with petroleum products such as engine oil, gasoline, etc. Windshield washers the fluid reservoir in the engine compartment should be checked for fluid level at regular intervals. Fill the reservoir with windshield antifre...

  • Page 284

    Have an authorized technician inspect the complete ex- haust system and adjacent body areas for broken, dam- aged, deteriorated, or mispositioned parts. Open seams or loose connections could permit exhaust fumes to seep into the passenger compartment. In addition, inspect the exhaust system each tim...

  • Page 285

    With the engine at normal operating temperature (but not running), check the cooling system pressure cap for proper vacuum sealing by draining a small amount of antifreeze/coolant from the radiator drain cock. If the cap is sealing properly, the antifreeze/coolant will begin to drain from the coolan...

  • Page 286

    Caution! • mixing of antifreeze/coolant other than the speci- fied hoat antifreeze/coolant may result in de- creased corrosion protection and engine damage. If a non-hoat antifreeze/coolant is introduced into the cooling system in an emergency, it should be replaced with the specified antifreeze/coo...

  • Page 287

    Use only high purity water such as distilled or deionized water when mixing the water/antifreeze (coolant) solu- tion. The use of lower quality water will reduce the amount of corrosion protection in the engine cooling system. Please note that it is the owner’s responsibility to main- tain the prope...

  • Page 288

    Children, do not store ethylene glycol based antifreeze/ coolant in open containers or allow it to remain in puddles on the ground. If ingested by a child, contact a physician immediately. Clean up any ground spills im- mediately. Engine coolant level the coolant bottle provides a quick visual metho...

  • Page 289

    • check antifreeze/coolant freeze point in the radiator and in the coolant recovery bottle. If antifreeze/ coolant needs to be added, contents of coolant recov- ery bottle must also be protected against freezing. • if frequent antifreeze/coolant additions are required, or if the level in the recover...

  • Page 290

    Are present. Components should be replaced immedi- ately if there is any evidence of degradation that could cause failure. Brake system in order to assure brake system performance, all brake system components should be inspected periodically. Refer to the appropriate “maintenance schedule” in sectio...

  • Page 291

    Warning! Worn brake hoses can burst and cause brake failure. You could have an accident. If you see any signs of cracking, scuffing, or worn spots, have the brake hoses replaced immediately. Brake master cylinder the fluid level in the master cylinder should be checked when performing under hood ser...

  • Page 292

    Should be checked when pads are replaced. However, low fluid level may be caused by a leak and a checkup may be needed. Use only manufacturer’s recommended brake fluid, refer to fluids, lubricants, and genuine parts for correct fluid type. Warning! • use of a brake fluid that may have a lower initia...

  • Page 293

    Caution! Using a transmission fluid other than the manufac- turer’s recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder. Using a transmission fluid other than the manufacturer’s recommended fluid will result in more frequent fluid and filter change...

  • Page 294

    (cross-hatched area) on the oil level indicator. The fluid level indicator should be in the cold region at 70° f (21° c) fluid temperature. If the fluid level is low, add sufficient fluid to bring to the proper level. Refer to fluids, lubricants and genuine parts for correct fluid type. Fluid is add...

  • Page 295

    Frequency of fluid change under normal operating conditions, the fluid installed at the factory will give satisfactory lubrication for the life of the vehicle. Fluid changes are not necessary unless the lubricant has become contaminated with water. If con- taminated with water, the fluid should be c...

  • Page 296

    Caution! When replacing plugs, do not overtighten. You could damage them and cause them to leak. Selection of lubricant use only manufacturer’s recommended fluid, refer to fluids, lubricants, and genuine parts for correct fluid type. Front/rear axle fluid fluid level check lubricant should be at bot...

  • Page 297

    Selection of lubricant use only manufacturer’s recommended fluid, refer to fluids, lubricants, and genuine parts for correct fluid type. Maintenance after off-road driving after extended operation in mud, sand or water, or similar dirty conditions, have your brake drums, brake linings, and axle join...

  • Page 298

    Trees and road surfaces during other seasons, are highly corrosive to the metal in your vehicle. Outside parking, which exposes your vehicle to airborne contaminants, road surfaces on which the vehicle is operated, extreme hot or cold weather and other extreme conditions will have an adverse effect ...

  • Page 299

    • avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish. Caution! Do not use abrasive or strong cleaning materials such as steel wool or scouring powder, which will scratch metal and painted surfaces. Special care • if you drive on salted or dusty ...

  • Page 300

    • if you carry special cargo such as chemicals, fertilizers, de-icer salt, etc., assure that such materials are well packaged and sealed. • if a lot of driving is done on gravel roads, consider mud or stone shields behind each wheel. • use mopar威 touch up paint on scratches or chips as soon as possi...

  • Page 301

    Cleaning plastic instrument cluster lenses the lenses in front of the instruments in this vehicle are molded in clear plastic. When cleaning the lenses, care must be taken to avoid scratching the plastic. 1. Clean with a wet soft rag. A mild soap solution may be used, but do not use high alcohol con...

  • Page 302

    Follow these steps to remove the carpet: 1. Unsnap the front and rear floor carpets. A snap is located on the outboard side of each front seat. 2. Remove the attachment cap from the front footwell area on both the driver and passenger side. The cap is removed by pulling it straight out. 3. Remove th...

  • Page 303

    • do not use harsh cleaners or bleaching agents on top material, as damage may result. • do not allow any vinyl cleaner to run down and dry on the paint, leaving a streak. • after cleaning your vehicle’s fabric top, always make sure it is completely dry before lowering. • be especially careful when ...

  • Page 304

    3. Always rinse thoroughly with cold water, then wipe with a soft and slightly moist, clean cloth. 4. When removing frost, snow or ice, never use a scraper or de-icing chemicals. Use warm water only if you must clean the window quickly. 5. Debris (sand, mud/dirt, dust, or salt) from off-road driving...

  • Page 305

    Fuse panel interior fuses the fuse panel is located behind the glove box. To access the fuse panel the glove box must be removed. It is removed by slipping the glove box strap off the hook and letting the door roll down off its hinges. To reinstall, position the glove box door at an 8 o’clock orient...

  • Page 306

    Cavity fuse description 1 20 amp yellow park lights, skim (sentry key) 2 20 amp yellow stop lights 3 20 amp yellow subwoofer system 4 10 amp red door switch defeat 5 10 amp red airbag 6 20 amp yellow rear wiper 7 10 amp red back-up lights, rear window defroster relay, abs 8 10 amp red hevac 9 10 amp...

  • Page 307

    Underhood fuses (power distribution center) your vehicle is equipped with an electrical power distri- bution center located in the engine compartment near the battery. This power center houses plug-in “cartridge” fuses, iso relays, and mini (micro) fuses. A label inside the latching cover of the cen...

  • Page 308

    Cavity fuse/color description 13 40 amp green accessories 14 open 15 50 amp red iod 16 open 17 20 amp yellow power 18 20 amp yellow horn 19 20 amp yellow fog lights 20 15 amp lt. Blue radio 21 10 amp red a/c clutch 22 25 amp natural ignition switch 23 20 amp yellow fuel 24 20 amp yellow off road 25 ...

  • Page 309

    Vehicle storage if you are leaving your vehicle dormant for more than 21 days you may want to take steps to protect your battery. You may: • remove cartridge fuse #15 in the power distribution center labeled ignition-off draw (iod). • store the removed iod fuse in the power distribution center locat...

  • Page 310

    Exterior lights bulb type backup lights (2). . . . . . . . . . . . . . . . . . . . . . . . 1156 center high mounted stop light (1) . . . . 921 or w16w fog lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . H3 front park/turn lights (2) . . . . . . . . . . . . . . . . . 3157 front sid...

  • Page 311

    4. Remove and replace the lamp. Front park/turn signal 1. Reach under the front fender and locate the front park/turn signal socket. 2. Turn the socket assembly counter–clockwise 1/3 turn and remove it from the housing. Pull the bulb straight from the socket to replace. Front side marker 1. Reach un...

  • Page 312

    3. Squeeze the bulb/element spring retainer from the reflector. 4. Disconnect the electrical connector. Caution! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol. 31...

  • Page 313

    Rear tail, stop, turn signal, and back-up lights 1. Remove the screws attaching the lens to the tailight housing. 2. Separate the lens from the housing. 3. Push the bulb in, turn it counter-clockwise 1/3 turn, then remove it from the housing, and replace. Center high mounted stop light (chmsl) the s...

  • Page 314

    Fluid capacities u.S. Metric fuel (approximate) 19 gallons 71.9 liters engine oil with filter 2.4 liter engine (sae 5w-30, api certified engine oil) 5 qts 4.7 liters 4.0 liter engine (sae 10w-30, api certified engine oil) 6 qts 5.7 liters cooling system * 2.4 liter engine (mopar 威 antifreeze/engine ...

  • Page 315

    Fluids, lubricants and genuine parts engine component fluid, lubricant, or genuine part engine coolant mopar 威 antifreeze/coolant 5 year/100,000 mile formula hoat (hybrid or- ganic additive technology) engine oil api certified sae 5w-30 engine oil is recommended for the 2.4l engine. Api certified sa...

  • Page 316

    Chassis component fluid, lubricant, or genuine part automatic transmission mopar 威 atf+4 automatic transmission fluid manual transmission mopar 威 manual transmission lubricant or equivalent (meeting the requirements of daimlerchrysler material standard ms-9224) transfer case mopar 威 atf+4 automatic ...

  • Page 317: Maintenance Schedules

    Maintenance schedules contents 䡵 emission control system maintenance . . . . . . . . 318 䡵 maintenance schedules . . . . . . . . . . . . . . . . . . . 318 ▫ schedule “b” . . . . . . . . . . . . . . . . . . . . . . . . 321 ▫ schedule “a” . . . . . . . . . . . . . . . . . . . . . . . . 332 8 m a i n t...

  • Page 318

    Emission control system maintenance the “scheduled” maintenance services, listed in bold type must be done at the times or mileages specified to assure the continued proper functioning of the emission control system. These, and all other maintenance services included in this manual, should be done t...

  • Page 319

    • off-road or desert driving • if equipped for and operated with e-85 (ethanol) fuel. Note: if any of these apply to you then change your engine oil every 3,000 miles (5 000 km) or 3 months, whichever comes first and follow “schedule b” of the “maintenance schedules” section of this manual. Note: if...

  • Page 320

    Once a month • check the tire pressure and look for unusual wear or damage. • inspect the battery and clean and tighten the terminals as required. • check the fluid levels of the coolant reservoir, brake master cylinder, and transmission, and add as needed. • check all lights and all other electrica...

  • Page 321

    Schedule “b” follow this schedule if you usually operate your vehicle under one or more of the following conditions. • day or night temperatures are below 32°f (0°c) • stop and go driving • excessive engine idling • driving in dusty conditions • short trips of less than 10 miles (16.2 km) • more tha...

  • Page 322

    Miles 3,000 6,000 9,000 12,000 15,000 (kilometers) (5 000) (10 000) (15 000) (20 000) (25 000) change the engine oil and engine oil filter, if not replaced at 3 months. X x x x x rotate the tires. X x inspect the engine air filter element, replace if necessary. X lubricate the steering linkage tie r...

  • Page 323

    Miles 18,000 21,000 24,000 27,000 30,000 (kilometers) (30 000) (35 000) (40 000) (45 000) (50 000) change the engine oil and engine oil filter, if not replaced at 3 months. X x x x x rotate the tires. X x x inspect the engine air filter element, replace if necessary. X inspect the pcv valve, and rep...

  • Page 324

    Miles 33,000 36,000 39,000 42,000 45,000 (kilometers) (55 000) (60 000) (65 000) (70 000) (75 000) change the engine oil and engine oil filter, if not replaced at 3 months. X x x x x rotate the tires. X x inspect the engine air filter element, replace if necessary. X lubricate the steering linkage t...

  • Page 325

    Miles 48,000 51,000 54,000 57,000 60,000 (kilometers) (80 000) (85 000) (90 000) (95 000) (100 000) change the engine oil and engine oil filter, if not replaced at 3 months. X x x x x rotate the tires. X x x inspect the engine air filter element, replace if necessary. X inspect the pcv valve, and re...

  • Page 326

    Miles 48,000 51,000 54,000 57,000 60,000 (kilometers) (80 000) (85 000) (90 000) (95 000) (100 000) inspect the drive belt and replace as needed. Not required if belt was previously. X drain and refill the transfer case fluid. X flush and replace the engine coolant/anti-freeze. X 326 schedule “b” 8 ...

  • Page 327

    Miles 63,000 66,000 69,000 72,000 75,000 (kilometers) (105 000) (110 000) (115 000) (120 000) (125 000) change the engine oil and engine oil filter, if not replaced at 3 months. X x x x x rotate the tires. X x inspect the engine air filter element, replace if necessary. X lubricate the steering link...

  • Page 328

    Miles 78,000 81,000 84,000 87,000 90,000 (kilometers) (130 000) (135 000) (140 000) (145 000) (150 000) change the engine oil and engine oil filter, if not replaced at 3 months. X x x x x rotate the tires. X x x inspect the engine air filter element, replace if necessary. X inspect the pcv valve, an...

  • Page 329

    Miles 93,000 96,000 99,000 102,000 105,000 (kilometers) (155 000) (160 000) (165 000) (170 000) (175 000) change the engine oil and engine oil filter, if not replaced at 3 months. X x x x x rotate the tires. X x inspect the engine air filter element, replace if necessary. X lubricate the steering li...

  • Page 330

    Miles 108,000 111,000 114,000 117,000 120,000 (kilometers) (180 000) (185 000) (190 000) (195 000) (200 000) change the engine oil and engine oil filter, if not replaced at 3 months. X x x x x rotate the tires. X x x inspect the engine air filter element, replace if necessary. X inspect the pcv valv...

  • Page 331

    Miles 108,000 111,000 114,000 117,000 120,000 (kilometers) (180 000) (185 000) (190 000) (195 000) (200 000) inspect the drive belt and replace as needed. Not required if belt was previously replaced. X drain and refill the transfer case fluid. X flush and replace the engine coolant/anti-freeze, if ...

  • Page 332

    Schedule “a” miles 6,000 12,000 18,000 24,000 30,000 (kilometers) (10 000) (20 000) (30 000) (40 000) (50 000) [months] [6] [12] [18] [24] [30] change the engine oil and engine oil filter. X x x x x rotate the tires. X x x x x inspect the engine air filter element, and replace if necessary. X replac...

  • Page 333

    Miles 36,000 42,000 48,000 54, 000 (kilometers) (60 000) (70 000) (80 000) (90 000) [months] [36] [42] [48] [54] change the engine oil and engine oil filter. X x x x rotate the tires. X x x x lubricate the steering and suspension ball joints. X x lubricate the steering linkage joints and outer tie r...

  • Page 334

    Miles 60,000 66,000 72,000 78,000 (kilometers) (100 000) (110 000) (120 000) (130 000) [months] [60] [66] [72] [78] change the engine oil and engine oil filter. X x x x rotate the tires. X x x x inspect the engine air filter element, and replace if nec- essary. X inspect the pcv valve, and replace i...

  • Page 335

    Miles 60,000 66,000 72,000 78,000 (kilometers) (100 000) (110 000) (120 000) (130 000) [months] [60] [66] [72] [78] flush and replace the engine coolant/anti-freeze. X inspect the manual transmission fluid, add as necessary. X inspect transfer case fluid. X schedule “a” 335 8 m a i n t e n a n c e s...

  • Page 336

    Miles 84,000 90,000 96,000 102, 000 (kilometers) (140 000) (150 000) (160 000) (170 000) [months] [84] [90] [96] [102] change the engine oil and engine oil filter. X x x x rotate the tires. X x x x inspect the engine air filter element, and replace if necessary. X inspect the pcv valve, and replace ...

  • Page 337

    Miles 108,000 114,000 120,000 (kilometers) (180 000) (190 000) (200 000) [months] [108] [114] [120] change the engine oil and engine oil filter. X x x rotate the tires. X x x inspect the engine air filter element, and replace if necessary. X replace the ignition cables (2.4l only). X inspect the pcv...

  • Page 338

    Miles 108,000 114,000 120,000 (kilometers) (180 000) (190 000) (200 000) [months] [108] [114] [120] inspect the manual transmission fluid, add as necessary. X drain and refill the transfer case fluid. X flush and replace the engine coolant/anti-freeze, if not done at 102,000 miles (170 000 km). X in...

  • Page 339: Contents

    If you need consumer assistance contents 䡵 suggestions for obtaining service for your vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . 340 ▫ prepare for the appointment . . . . . . . . . . . . 340 ▫ prepare a list . . . . . . . . . . . . . . . . . . . . . . . . 340 ▫ be reasonable with re...

  • Page 340

    Suggestions for obtaining service for your vehicle prepare for the appointment if you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty, discuss additional charges with the service manager. ...

  • Page 341

    Technicians, special tools, and the latest information to assure your vehicle is fixed correctly and in a timely manner. This is why you should always talk to your dealer’s service manager first. Most matters can be resolved with this process. • if for some reason you are still not satisfied, talk t...

  • Page 342

    Customer assistance for the hearing or speech impaired (tdd/tty) to assist customers who have hearing difficulties, the manufacturer has installed special tdd (telecommuni- cation devices for the deaf) equipment at its customer center. Any hearing or speech impaired customer who has access to a tdd ...

  • Page 343

    Warranty information (u.S. Vehicles only) see the warranty information booklet for the terms and provisions of daimlerchrysler’s warranties applicable to this vehicle. Mopar 姞 parts mopar 威 fluids, lubricants, parts, and accessories are available from your dealer. They will help you keep your vehicl...

  • Page 344

    Publication order forms to order the following manuals, you may use either the website or the phone numbers listed below. Visa, mas- tercard, american express, and discover orders are ac- cepted. If you prefer mailing your payment, please call for an order form. Note: a street address is required wh...

  • Page 345

    Call toll free at: • 1–800–890–4038 (u.S.) • 1–800–387–1143 (canada) or visit us on the world wide web at: • www.Techauthority.Daimlerchrysler.Com • www.Daimlerchrysler.Ca/manuals department of transportation uniform tire quality grades the following describes the tire grading categories estab- lish...

  • Page 346

    Warning! The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics. Temperature grades the temperature grades are a (the highest), b, and c, representing the tire’s resistan...

  • Page 347: Index

    Index 10

  • Page 348

    About your brakes . . . . . . . . . . . . . . . . . . . . . . . 203 abs (anti-lock brake system) . . . . . . . . . . . . 151,205 add-a-trunk . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 adding washer fluid . . . . . . . . . . . . . . . . . . . . . 141 air cleaner, engine (engine air clea...

  • Page 349

    Emergency starting . . . . . . . . . . . . . . . . . . . . . 258 voltmeter . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147 belts, drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . 275 belts, seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 body mechanism lu...

  • Page 350

    Child restraint tether anchors . . . . . . . . . . . . . 38,39 climate control . . . . . . . . . . . . . . . . . . . . . . . . . 172 clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152 clutch interlocking ignition system . . . . . . . . 182,187 compact disc (cd) maintenance . ....

  • Page 351

    Dipsticks oil (engine) . . . . . . . . . . . . . . . . . . . . . . . . . . 271 disabled vehicle towing . . . . . . . . . . . . . . . . . . . 261 disposal engine oil . . . . . . . . . . . . . . . . . . . . . . . . . . . 274 used coolant (antifreeze) . . . . . . . . . . . . . . . . 287 door locks . . ...

  • Page 352

    Oil filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . 274 oil pressure gauge . . . . . . . . . . . . . . . . . . . . . 149 oil selection . . . . . . . . . . . . . . . . . . . . . . . . . . 314 overheating . . . . . . . . . . . . . . . . . . . . . . . . . . 253 starting . . . . . . . . ....

  • Page 353

    Shifting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 196 four wheel drive operation . . . . . . . . . . . . . 194,195 front axle (differential) . . . . . . . . . . . . . . . . . . . 296 fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 229 filler cap (gas cap) . . ...

  • Page 354

    Dimmer switch . . . . . . . . . . . . . . . . . . . . . . . . 65 replacing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 310 switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 heater . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 172 heater, engine block...

  • Page 355

    Key-in reminder . . . . . . . . . . . . . . . . . . . . . . . . . 14 keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 lane change and turn signals . . . . . . . . . . . . . . 147 lap belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 lap/shoulder belts . . ...

  • Page 356

    Turn signal . . . . . . . . . . . . . . . . . . . 66,147,311,313 warning (instrument cluster description) . . . . . 147 loading vehicle tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 217 locking axle . . . . . . . . . . . . . . . . . . . . . . . . . . . 199 locks . . . . . . . ....

  • Page 357

    Octane rating, gasoline (fuel) . . . . . . . . . . . . . . 230 odometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150 trip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150 off-pavement driving (off-road) . . . . . . . . . . . . 209 off-road driving (off-pavement) ....

  • Page 358

    Radio (sound systems) . . . . . . . . . . . . . . . . . 154,160 rear axle (differential) . . . . . . . . . . . . . . . . . . . . 296 rear window defroster . . . . . . . . . . . . . . . . . . . 139 rear window features . . . . . . . . . . . . . . . . . . . . 139 rear wiper/washer . . . . . . . . . . ...

  • Page 359

    Reminder . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148 seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 rear folding . . . . . . . . . . . . . . . . . . . . . . . . . . 59 rear seat cushion re...

  • Page 360

    Steering power . . . . . . . . . . . . . . . . . . . . . . . . . . . 207,281 tilt column . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 wheel lock . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 wheel, tilt . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 storage . . . ....

  • Page 361

    Tongue weight/trailer weight . . . . . . . . . . . . . . 240 torque converter clutch . . . . . . . . . . . . . . . . . . 194 towing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 236,261 disabled vehicle . . . . . . . . . . . . . . . . . . . . . . . 261 guide . . . . . . . . . . . . . . . ....

  • Page 362

    Vehicle modifications/alterations . . . . . . . . . . . . . . 9 vehicle storage . . . . . . . . . . . . . . . . . . . . . . . . . 309 viscosity, engine oil . . . . . . . . . . . . . . . . . . . . . . 274 voltmeter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147 warning lights (instrume...

  • Page 363: Notes

    Notes.

  • Page 364: Notes

    Notes.

  • Page 365: Notes

    Notes.

  • Page 366: Notes

    Notes.

  • Page 367: Notes

    Notes.

  • Page 368: Notes

    Notes.