1. DL manuals
  2. Jeep
  3. Automobile
  4. 2007 Cherokee
  5. Owner's Manual

Jeep 2007 Cherokee Owner's Manual

Summary of 2007 Cherokee

  • Page 1

    Table of contents section page 1 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 things to know before starting your vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 3 understanding the fea...

  • Page 3: Introduction

    Introduction contents 䡵 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 ▫ roll over warning . . . . . . . . . . . . . . . . . . . . . 4 䡵 how to use this manual . . . . . . . . . . . . . . . . . . 6 䡵 warnings and cautions . . . . . . . . . . . . . . . . . . . 8 䡵 vehicle identi...

  • Page 4

    Introduction thank you for selecting a jeep 威 grand cherokee and welcome to our worldwide family. This is a specialized utility vehicle designed for both on-road and off-road use. It can go places and perform tasks for which conventional two-wheel drive vehicles were not intended. However, on-road r...

  • Page 5

    Do not attempt sharp turns or abrupt maneuvers or other unsafe driving actions that can cause loss of vehicle control. Failure to operate this vehicle safely may result in an accident, roll over of the vehicle, and severe or fatal injury. Drive carefully. Failure to use driver and passenger seat bel...

  • Page 6

    Note: after you read the manual, it should be stored in the vehicle for convenient reference and remain with the vehicle when sold so that the new owner will be aware of all safety warnings. When it comes to service, remember that your authorized dealer knows your vehicle best, has the factory-train...

  • Page 7

    Introduction 7 1.

  • Page 8

    Warnings and cautions this manual contains warnings against operating procedures which could result in an accident or bodily injury. It also contains cautions against procedures which could result in damage to your vehicle. If you do not read this entire manual you may miss important information. Ob...

  • Page 9

    Vehicle modifications / alterations warning! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death. Introduction 9 1.

  • Page 11: Contents

    Things to know before starting your vehicle contents 䡵 a word about your keys . . . . . . . . . . . . . . . . . .14 ▫ ignition key removal . . . . . . . . . . . . . . . . . . .14 ▫ key-in-ignition reminder . . . . . . . . . . . . . . . .15 䡵 sentry key immobilizer system . . . . . . . . . . . . . .1...

  • Page 12

    ▫ transmitter battery service . . . . . . . . . . . . . . .23 䡵 remote starting system — if equipped . . . . . . . .24 䡵 door locks . . . . . . . . . . . . . . . . . . . . . . . . . . . .26 ▫ manual door locks . . . . . . . . . . . . . . . . . . . . .26 ▫ power door locks — if equipped . . . . . . ....

  • Page 13

    ▫ safety checks you should make inside the vehicle . . . . . . . . . . . . . . . . . . . . . . . . . .65 ▫ safety checks you should make outside the vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66 things to know before starting your vehicle 13 2.

  • Page 14

    A word about your keys the keys for your new vehicle are enclosed in a plastic bag with the key code number on it. If you received your keys without the bag, ask your authorized dealer to give you the number. The key code can also be obtained by your authorized dealer from your vehicle invoice. Igni...

  • Page 15

    Warning! Leaving children in a vehicle unattended is danger- ous for a number of reasons. A child or others could be injured. Children should be warned not to touch the parking brake, brake pedal or the gear selector lever. Don’t leave the keys in the ignition. A child could operate power windows, o...

  • Page 16

    Light will come on for 3 seconds immediately after the ignition switch is turned on for a bulb check. Afterwards, if the bulb remains on, this indicates a malfunction in the electronics. If the bulb begins to flash immediately after the ignition switch is turned on, this indicates that an invalid ke...

  • Page 17

    Replacement keys note: only keys that have been programmed to the vehicle electronics can be used to start the vehicle. Once a sentry key has been programmed to a vehicle, it cannot be programmed to any other vehicle. At the time of purchase, the original owner is provided with a four digit pin numb...

  • Page 18

    4. Insert a blank sentry key into the ignition switch and turn the ignition switch on within 60 seconds. After 10 seconds, a single chime will sound. The skim indicator light will stop flashing, turn on for 3 seconds; then turn off. The new sentry key has been programmed. Repeat this process to prog...

  • Page 19

    The door lock plunger located on the inside of the doors or with the driver’s door key lock cylinder, will not set the alarm. To disarm the system to disarm the system, use the remote keyless entry transmitter. Also, using a valid sentry key and moving the ignition switch to the on/start position wi...

  • Page 20

    Note: if the key is in the ignition switch, then all buttons on that transmitter will be disabled. The buttons on the remaining transmitters will work. If the vehicle is shifted out of p (park), all the transmitter buttons are disabled for all keys. To unlock the doors press and release the “unlock”...

  • Page 21

    Note: if desired, the system can be programmed to unlock all doors on the first press of the “unlock” button. Refer to “remote unlock driver’s door 1st” in the personal settings section of the “electronic vehicle infor- mation center (evic)”, or simply follow these steps: 1. Press and hold the “lock...

  • Page 22

    Warning! Driving with the flipper glass open can allow poi- sonous exhaust gases into your vehicle. You and your passengers could be injured by these fumes. Keep the flipper glass closed when you are operating the vehicle. Using the panic alarm to turn the panic alarm feature on or off, press and ho...

  • Page 23

    2. While the “unlock” button is pressed, (after 4 seconds) press the “lock” button. Release both buttons. The “flash lights on lock/unlock” feature can be reactivated by repeating this procedure. General information this device complies with part 15 of the fcc rules and rss 210 of industry canada. O...

  • Page 24

    1. With the transmitter buttons facing down, remove the small screw, and separate the two halves of the transmit- ter. Make sure not to damage the rubber gasket during removal. 2. Remove and replace the battery. Avoid touching the new battery with your fingers. Skin oils may cause battery deteriorat...

  • Page 25

    Once the vehicle has started, the engine will run for 15 minutes. To cancel remote start, press the “remote start” button twice within two seconds. To enter the vehicle while the engine is running during a remote start, you must first unlock the vehicle using the “unlock” button on the key fob. Afte...

  • Page 26

    Door locks manual door locks use the manual door lock plunger to lock the doors from inside the vehicle. If the plunger is down when the door is closed, the door will lock. Therefore, make sure the keys are not inside the vehicle before closing the door. Warning! • for personal security and safety i...

  • Page 27

    If you press the door lock switch while the keys are in the ignition switch, and the driver’s door is open, the doors will not lock. The rear doors cannot be opened from inside the vehicle until you pull up the lock plungers. Automatic door locks if this feature is selected your door locks will lock...

  • Page 28

    Child protection door lock the rear doors of your vehicle are equipped with child protection locks. If you push up on the lever on the open edge of the door it cannot be opened from the inside of the vehicle. Push the lever down to disengage the child protection locks. Warning! Avoid trapping anyone...

  • Page 29

    Windows power windows the power window controls are located on the driver’s door trim panel. There is a single switch on the front passenger door/rear doors which operates the front passenger/rear passenger door windows. The window controls will operate only when the ignition switch is in the on or ...

  • Page 30

    Auto down both the driver and front passenger window switch has an “auto down” feature. Press the window switch past the first detent, release, and the window will go down automatically. To cancel the “auto down” movement, operate the switch in either the up or down direction and release the switch....

  • Page 31

    Warning! There is no anti-pinch protection when the window is almost closed. Be sure to clear all objects from the window before closing. Resetting the auto-up feature should the auto-up feature stop working the window probably needs to be reset. To reset auto-up: pull the window switch up and close...

  • Page 32

    Wind buffeting wind buffeting can be described as the perception of pressure on the ears or a helicopter type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions. This is a normal occur- rence and ...

  • Page 33

    Warning! Driving with the liftgate open can allow poisonous exhaust gases into your vehicle. You and your pas- sengers could be injured by these fumes. Keep the liftgate closed when you are operating the vehicle. Liftgate flipper glass the liftgate flipper glass is also unlocked when the liftgate is...

  • Page 34

    Once the liftgate flipper glass has been opened, connec- tion to the rear window wiper is interrupted, preventing activation of the rear wiper blade while the flipper glass is open. Note: if a power malfunction to the power liftgate latch should occur, an emergency liftgate latch release can be used...

  • Page 35

    Warning! In a collision, you and your passengers can suffer injuries, including fatalities, if you are not properly buckled up. You can strike the interior of your vehicle or other passengers, or you can be thrown out of the vehicle. Always be sure you and others in your vehicle are buckled up prope...

  • Page 36

    Warning! • wearing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body. These are the strongest parts of your body and can take the forces of a collision the best. Wearing your belt in the wrong place could make your injuries in a collision much wo...

  • Page 37

    3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” latch plate latch plate to buckle things to know before starting your vehicle 37 2.

  • Page 38

    Warning! A belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. A belt that is too loose will not protect you as well. In a sudden stop you ...

  • Page 39

    5. Position the shoulder belt on your chest so that it is comfortable and not resting on your neck. The retractor will withdraw any slack in the belt. 6. To release the belt, push the red button marked press on the buckle. The belt will automatically retract to its stowed position. If necessary, sli...

  • Page 40

    Adjustable upper shoulder belt anchorage in the front seating positions, the shoulder belt can be adjusted upward or downward to position the belt away from your neck. Press the release button to release the anchorage, and then move it up or down to the position that serves you best. As a guide, if ...

  • Page 41

    3. Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode. How to disengage the automatic locking mode disconnect the combination lap/shoulder belt and allow it to retract completely to disengage the automa...

  • Page 42

    Note: these devices are not a substitute for proper seat belt placement by the occupant. The seat belt must still be worn snugly and positioned properly. The pretensioners are triggered by the occupant re- straint control (orc) module. Like the front airbags, the pretensioners are a single use item....

  • Page 43

    Driver and front passenger supplemental restraint systems (srs) this vehicle has airbags for both the driver and right front passenger as a supplement to the seat belt restraint systems. The driver’s front airbag is mounted in the steering wheel. The passenger side airbag is mounted in the instrumen...

  • Page 44

    Note: airbag covers may not be obvious in the interior trim; but they will open to allow airbag deployment. Warning! • do not put anything on or around the front airbag covers or attempt to manually open them. You may damage the airbags and you could be injured because the airbags are no longer func...

  • Page 45

    Note: do not use a clothing bar mounted to the coat hooks in this vehicle. A clothing bar will impede the proper performance of the window bags. The front airbags have a multi stage inflator design. This allows the airbag to have different rates of inflation that are based on collision severity. Alo...

  • Page 46

    Children that are not big enough to properly wear the vehicle seat belt should be secured in the rear seat, in a child restraint or belt-positioning booster seat. Older children who do not use child restraints or belt- positioning booster seats should ride properly buckled up in the rear seat. Never...

  • Page 47

    Warning! • relying on the airbags alone could lead to more severe injuries in a collision. The airbags work with your seat belt to restrain you properly. In some collisions the airbags won’t deploy at all. Always wear your seat belts even though you have airbags. • being too close to the steering wh...

  • Page 48

    • driver and front passenger seat belt pretensioners how the airbag system works • the occupant restraint control (orc) module de- termines if a frontal, side, or rollover collision is severe enough to require the front and/or side airbags to inflate. The front airbag inflators are designed to provi...

  • Page 49

    • the driver and passenger airbag/inflator units are located in the center of the steering wheel and the right side of the instrument panel. When the orc detects a collision requiring the airbags, it signals the inflator units. A large quantity of nontoxic gas is generated to inflate the front airba...

  • Page 50

    If a deployment occurs the airbag system is designed to deploy when the occupant restraint control (orc) module detects a moderate-to-severe frontal collision, to help restrain the driver and front passenger, and then to immediately deflate. Note: a frontal collision that is not severe enough to nee...

  • Page 51

    Warning! Deployed airbags and seat belt pretensioners cannot protect you in another collision. Have the airbags, seat belt pretensioners, and seat belt retractor assem- bly, replaced by an authorized dealer as soon as possible. Enhanced accident response feature if the airbags deploy after an impact...

  • Page 52

    Airbag warning light you will want to have the airbag system ready to inflate for your protection in an impact. The airbag system is designed to be maintenance free. If any of the following occurs, have an authorized dealer service the system promptly: • does not come on during the 6 to 8 seconds af...

  • Page 53

    Provided to the custodial entity upon request. General data that does not identify particular vehicles or crashes may be released for incorporation in aggregate crash databases, such as those maintained by the us govern- ment and various states. Data of a potentially sensitive nature, such as would ...

  • Page 54

    Child restraint everyone in your vehicle needs to be buckled up all the time — babies and children, too. Every state in the united states and all canadian provinces require that small children ride in proper restraint systems. This is the law, and you can be prosecuted for ignoring it. Children 12 y...

  • Page 55

    • the infant carrier is only used rearward-facing in the vehicle. It is recommended for children who weigh up to about 20 lbs (9 kg). “convertible” child seats often have a higher weight limit in the rearward-facing direction than infant carriers do, so they can be used rearward-facing by children w...

  • Page 56

    Standards. The manufacturer also recommends that you try a child restraint in the vehicle seats where you will use it before you buy it. • the restraint must be appropriate for your child’s weight and height. Check the label on the restraint for weight and height limits. • carefully follow the instr...

  • Page 57

    • if the belt still cannot be tightened, or if pulling and pushing on the restraint loosens the belt, disconnect the latch plate from the buckle, turn the buckle around, and insert the latch plate into the buckle again. If you still cannot make the child restraint secure, try a different seating pos...

  • Page 58

    Children too large for booster seats children who are large enough to wear the shoulder belt comfortably, and whose legs are long enough to bend over the front of the seat when their back is against the seat back, should use the lap/shoulder belt in a rear seat. • make sure that the child is upright...

  • Page 59

    Kits or retro-fit kits. You are urged to take advantage of all the available attachments provided with your child re- straint in any vehicle. Note: when using the latch attaching system to install a child restraint, please ensure that all seat belts not being used for occupant restraints are stowed ...

  • Page 60

    Installing the latch-compatible child restraint system we urge that you carefully follow the directions of the manufacturer when installing your child restraint. Not all child restraint systems will be installed as described here. Again, carefully follow the installation instructions that were provi...

  • Page 61

    In addition, there are tether strap anchorages behind each rear seating position located on the back of the seat. Many, but not all restraint systems will be equipped with separate straps on each side, with each having a hook or connector for attachment to the lower anchorage and a means of adjustin...

  • Page 62

    Warning! Improper installation of a child restraint to the latch anchorages can lead to failure of an infant or child restraint. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint. Installing child restraints using th...

  • Page 63

    If the belt still can’t be tightened, or if by pulling and pushing on the restraint loosens the belt, you may need to do something more. Disconnect the latch plate from the buckle, turn the buckle around, and insert the latch plate into the buckle again. If you still can’t make the child restraint s...

  • Page 64

    Transporting pets airbags deploying in the front seat could harm your pet. An unrestrained pet will be thrown about and possibly injured, or injure a passenger during panic braking or in a collision. Pets should be restrained in the rear seat in pet harnesses or pet carriers that are secured by seat...

  • Page 65

    Safety tips exhaust gas warning! Exhaust gases can injure or kill. They contain carbon monoxide (co) which is colorless and odorless. Breath- ing it can make you unconscious and can eventually poison you. To avoid breathing (co) follow the safety tips below. • do not inhale exhaust gases. They conta...

  • Page 66

    Seat belt assemblies must be replaced after an accident if they have been damaged (bent retractor, torn webbing, etc.). If there is any question regarding belt or retractor condition, replace the belt. Airbag warning light the light should come on and remain on for 6 to 8 seconds as a bulb check whe...

  • Page 67: Contents

    Understanding the features of your vehicle contents 䡵 mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72 ▫ inside day/night mirror . . . . . . . . . . . . . . . . .72 ▫ automatic dimming mirror — if equipped . . . .72 ▫ outside mirrors . . . . . . . . . . . . . . . . . . . . . ....

  • Page 68

    ▫ advanced phone connectivity . . . . . . . . . . . . .92 ▫ things you should know about your uconnect™ system . . . . . . . . . . . . . . . . . . . . .94 䡵 seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .99 ▫ front manual seat adjustment . . . . . . . . . . . . .99 ▫ front se...

  • Page 69

    ▫ daytime running lights — if equipped . . . . . 116 ▫ lights-on reminder . . . . . . . . . . . . . . . . . . . 117 ▫ fog lights — if equipped . . . . . . . . . . . . . . . 117 ▫ turn signals . . . . . . . . . . . . . . . . . . . . . . . . . 117 ▫ high beam switch . . . . . . . . . . . . . . . . . ....

  • Page 70

    ▫ bas (brake assist system) . . . . . . . . . . . . . . . 131 ▫ erm (electronic roll mitigation) . . . . . . . . . . 132 ▫ esp (electronic stability program) . . . . . . . . . 133 ▫ esp/bas warning lamp and esp/tcs indicator light . . . . . . . . . . . . . . . . . . . . . . . 137 䡵 rear park assist ...

  • Page 71

    ▫ closing sunroof - express . . . . . . . . . . . . . . . 154 ▫ pinch protect feature . . . . . . . . . . . . . . . . . . . 154 ▫ pinch protect override . . . . . . . . . . . . . . . . . 154 ▫ venting sunroof - express . . . . . . . . . . . . . . . 154 ▫ sunshade operation . . . . . . . . . . . . . ...

  • Page 72

    Mirrors inside day/night mirror the mirror should be adjusted to center on the view through the rear window. A two-point pivot system allows for horizontal and vertical adjustment of the mirror. Annoying headlight glare from vehicles behind you can be reduced by moving the small control under the mi...

  • Page 73

    Caution! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror. Apply the solution onto a clean cloth and wipe the mirror clean. Outside mirrors to receive maximum benefit, adjust the outside mirrors to center on the adjacent lane of traffic with a...

  • Page 74

    Warning! Vehicles and other objects seen in the passenger side convex mirror will look smaller and farther away than they really are. Relying too much on your passenger side convex mirror could cause you to collide with another vehicle or other object. Use your inside mirror when judging the size or...

  • Page 75

    Both mirrors will always move together and will fold anytime the knob is turned. The ignition switch does not have to be in the on position. Driver’s outside automatic dimming mirror — if equipped if your vehicle is equipped with a driver’s outside auto- matic dimming mirror, it operates when the in...

  • Page 76

    Power mirror preselected positions can be controlled by the optional memory seat feature. Refer to “driver memory seat” in this section for details. (see page 106 for more information.) heated remote control mirrors — if equipped these mirrors are heated to melt frost or ice. This feature is activat...

  • Page 77

    Hands–free communication (uconnect™) — if equipped uconnect™ is a voice-activated, hands-free, in- vehicle communications system. Uconnect™ allows you to dial a phone number with your cellular phone using simple voice commands (e.G., ⬙call” ѧ “mike” ѧ”work⬙ or ⬙dial” ѧ “248-555-1212⬙). Your cellular...

  • Page 78

    The rearview mirror contains the microphone for the system and the control buttons that will enable you to access the system. The uconnect™ system can be used with any hands- free profile certified bluetooth™ cellular phone. See www.Chrysler.Com/uconnect for supported phones. If your cellular phone ...

  • Page 79

    Operations voice commands can be used to operate the uconnect™ system and to navigate through the uconnect™ menu structure. Voice commands are required after most uconnect™ system prompts. You will be prompted for a specific command and then guided through the available options. • prior to giving a ...

  • Page 80

    Cancel command at any prompt, after the voice on beep, you can say ⬙cancel⬙ and you will be returned to the main menu. However, in a few instances the system will take you back to the previous menu. Pair (link) uconnect™ system to a cellular phone to begin using your uconnect™ system, you must pair ...

  • Page 81

    • for identification purposes, you will be prompted to give the uconnect™ system a name for your cellular phone. Each cellular phone that is paired should be given a unique phone name. • you will then be asked to give your cellular phone a priority level between 1 and 7, 1 being the highest priority...

  • Page 82

    • system will prompt you to say the name of the person you want call. • after the ⬙ready⬙ prompt and the following beep, say the name of the person you want to call. For example, you can say ⬙john doe,⬙ where john doe is a previ- ously stored name entry in the uconnect™ phone- book. Refer to ⬙add na...

  • Page 83

    The uconnect™ system will allow you to enter up to 32 names in the phonebook with each name having up to four associated phone numbers and designations. Each language has a separate 32-name phonebook accessible only in that language. Edit entries in the uconnect™ phonebook note: editing phonebook en...

  • Page 84

    • after the ⬙ready⬙ prompt and the following beep, say ⬙phonebook delete.⬙ • after you enter the phonebook delete menu, you will then be asked for the name of the entry that you wish to delete. You can either say the name of a phonebook entry that you wish to delete or you can say ⬙list names ⬙ to h...

  • Page 85

    • the uconnect™ system will play the names of all the phonebook entries. • to call one of the names in the list, press the ⬙voice recognition’ button during the playing of the desired name, and then say ⬙call.⬙ note: the user can also exercise ⬙edit⬙ or ⬙delete⬙ operations at this point. • the uconn...

  • Page 86

    Making a second call while current call in progress to make a second call while you are currently in a call, press the ’voice recognition’ button and say ⬙dial⬙ or ⬙call⬙ followed by the phone number or phonebook entry you wish to call. The first call will be on hold while the second call is in prog...

  • Page 87

    Call termination to end a call in progress, momentarily press the ⬘phone’ button. Only the active call(s) will be terminated and if there is a call on hold, it will become the new active call. Redial • press the ’phone’ button to begin. • after the ⬙ready⬙ prompt and the following beep, say ⬙redial....

  • Page 88

    • after the ⬙ready⬙ prompt and the following beep, say the name of the language you wish to switch to (english, espanol, or francais, if so equipped). • continue to follow the system prompts to complete language selection. After selecting one of the languages, all prompts and voice commands will be ...

  • Page 89

    Your phone must be turned on and paired to the ucon- nect™ system to allow use of this vehicle feature in emergency situations when the cell phone has network coverage and stays paired to the uconnect™ system. Towing assistance if you need towing assistance, • press the ’phone’ button to begin. • af...

  • Page 90

    When calling a number with your uconnect™ system that normally requires you to enter in a touch-tone sequence on your cellular phone keypad, you can push the ’voice recognition’ button and say the sequence you wish to enter followed by the word ⬙send.⬙ for example, if required to enter your pin numb...

  • Page 91

    Dialing using the cellular phone keypad you can dial a phone number with your cellular phone keypad and still use the uconnect™ system (while dialing via the cell phone keypad, the user must exercise caution and take precautionary safety measures). By dialing a number with your paired bluetooth™ cel...

  • Page 92

    Information service when using at&t wireless service, dialing to phone number ⬙#121,⬙ you can access voice activated automated system to receive news, weather, stocks, traffic, etc. Related information. Advanced phone connectivity transfer call to and from cellular phone the uconnect™ system allows ...

  • Page 93

    Select another cellular phone this feature allows you to select and start using another phone with the uconnect™ system. The phone must have been previously paired to the uconnect™ system that you want to use it with. • press the ’phone’ button to begin. • after the ⬙ready⬙ prompt and the following ...

  • Page 94

    Things you should know about your uconnect™ system voice recognition (vr) • always wait for the beep before speaking. • speak normally, without pausing, just as you would speak to a person sitting approximately eight (8) feet away from you. • make sure that no one other than you is speaking during a...

  • Page 95

    • you can say ⬙o⬙ (letter ⬙o⬙) for ⬙0⬙ (zero). ⬙800⬙ must be spoken ⬙eight-zero-zero.⬙ • even though international dialing for most number combinations is supported, some shortcut dialing number combinations may not be supported. Far end audio performance • audio quality is maximized under: • low-to...

  • Page 96

    96 understanding the features of your vehicle.

  • Page 97

    Understanding the features of your vehicle 97 3.

  • Page 98

    98 understanding the features of your vehicle.

  • Page 99

    North american english primary alternate(s) zero oh add location add new all all of them confirmation prompts confirmations prompts delete a name delete language select language list names list all list paired phones list phones pager beeper phone pairing pairing phonebook phone book return to main ...

  • Page 100

    Front seat adjustment — recline to adjust the seatback, lift the lever located on the outboard side of the seat, lean back, and release the lever at the desired position. To return the seatback, lift the lever, lean forward, and release the lever. Warning! Do not ride with the seatback reclined so t...

  • Page 101

    Manual lumbar support adjustment the manual lumbar support adjustment lever is located on the right side of the driver’s seat and on the left side of the passenger’s seat. Moving the lumbar control lever fore and aft increases or decreases the lumbar support. 8 - way driver’s power seat the driver’s...

  • Page 102

    4 - way passenger’s power seat — if equipped the front passenger’s power seat switches are located on the outboard side of the passenger seat lower side trim. The bottom switch controls forward/rearward adjust- ment. The top switch controls the seatback recline adjust- ment. Note: the 4 - way seat d...

  • Page 103

    Center of the instrument panel. After turning on the ignition, you can choose from high, off, or low heat settings. Amber leds in the top portion of each switch indicate the level of heat in use. Two leds are illumi- nated for high, one for low, and none for off. Pressing the switch once will select...

  • Page 104

    Warning! Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaus- tion or other physical condition must exercise care when using the seat heater. It may cause burns even at low temperatures, especially if...

  • Page 105

    Note: do not fold the rear seat down with the center seat belt buckled. 2. Fold the rear seat completely forward. Note: the automatic folding rear head restraints will lower as the seat is folded down. To raise rear seat raise the rear seatback and lock it into place. If interfer- ence from the carg...

  • Page 106

    Storage — rear seat armrest (if equipped) the rear seat may be equipped with a center storage armrest. Press the latch and lift the top of the armrest to access the storage bin. Driver memory seat — if equipped once programmed, the memory buttons 1 and 2 on the driver’s door panel can be used to rec...

  • Page 107

    Keyless entry transmitters can also be programmed to recall the same positions when the “unlock” button is pressed. Your vehicle may have been delivered with two remote keyless entry transmitters. One or both transmitters can be linked to either memory position. The memory system can accommodate up ...

  • Page 108

    4. Adjust the brake and accelerator pedals to the desired positions. 5. Turn on the radio and set the radio station presets (up to 10 am and 10 fm stations can be set). 6. Turn the ignition switch to the off position and remove the key. 7. Press and release the set (s) button located on the driver’s...

  • Page 109

    To recall the memory settings for driver one, press memory button number 1 on the driver’s door or the “unlock” button on the remote keyless entry transmit- ter linked to memory position 1. To recall the memory setting for driver two, press memory button number 2 on the driver’s door or the “unlock”...

  • Page 110

    Note: once programmed, all transmitters linked to memory can be easily enabled or disabled at one time. Refer to remote linked to memory under ⬙electronic vehicle information center (evic) — customer pro- grammable features ⬙ in section 4 for more information. Easy entry/exit seat this feature provi...

  • Page 111

    Note: the easy entry easy exit feature is not enabled when the vehicle is delivered from the factory. The easy entry easy exit feature is enabled (or later disabled) through the programmable features in the electronic vehicle information center (evic). Refer to ⬙electronic vehicle information center...

  • Page 112

    Then, reach under the hood, move safety latch to the left, and lift the hood. To prevent possible damage, do not slam the hood to close it. Use a firm downward push at the center of the hood to ensure that both latches engage. Warning! If the hood is not fully latched, it could fly up when the vehic...

  • Page 113

    Lights multi-function control lever the multi-function control lever controls the operation of the headlights, turn signals, headlight beam selection, instrument panel light dimming, passing light, interior courtesy/dome lights, and optional fog lights. Battery saver feature—exterior/interior lights...

  • Page 114

    Headlights and parking lights turn the end of the multi-function control lever to the first detent for parking light operation. Turn to the second detent for headlight operation. Turn to the third detent for “auto” headlight operation (if equipped). Automatic headlight system — if equipped turn the ...

  • Page 115

    Stop. Refer to “windshield wipers and washers” in this section for more information. (see page 120 for more information.) note: when your headlights come on during the daytime, the instrument panel lights will automatically dim to the lower nighttime intensity. Refer to “instru- ment panel and inter...

  • Page 116

    To deactivate 1. Pull back on the muti-function control lever to manu- ally deactivate the system (normal operation of high beams). 2. Pull back on the multi-function control lever once again to re-activate the system. Note: broken, muddy, or obstructed headlights and taillights of vehicles in the f...

  • Page 117

    Lights-on reminder if the headlights or parking lights are on after the ignition is turned off, a chime will sound when the driver’s door is opened. Fog lights — if equipped the fog light switch is located in the multi- function control lever. To activate the fog lights, turn on the park/turn lights...

  • Page 118

    High beam switch pull the multi-function control lever towards you to switch the headlights to “high” beam. The “high beam indicator light” on the instrument cluster will illumi- nate. Pull the multi-function control lever a second time to switch the headlights to “low” beam. Passing light you can s...

  • Page 119

    Front map/reading lights these lights are mounted in the overhead console. Each light can be turned on by pressing the recessed area of the lens. To turn these lights off, press the recessed area of the lens a second time. There are also reading lights located above the rear doors. Each light can be...

  • Page 120

    Windshield wipers and washers the front and rear wipers and washers are operated by a switch in the right side control lever. Turn the end of the control lever to select “lo,” “hi,” or one of the five speed sensitive intermittent windshield wiper speeds. Refer to “speed sensitive intermittent wiper ...

  • Page 121

    To use the washer, pull the lever toward you and hold while spray is desired. If the lever is pulled while in the delay range, the wiper will operate for several seconds after the lever is released, and then resume the intermit- tent interval previously selected. If the lever is pulled while in the ...

  • Page 122

    Rain sensing wipers—if equipped this feature senses moisture on the windshield and automatically activates the wipers for the driver. The feature is especially useful for road splash or overspray from the windshield washers of the vehicle ahead. Rotate the end of the multi-function lever to one of f...

  • Page 123

    Driver desires more sensitivity. Place the wiper switch in the off position when not using the system. Note: • the rain sensing feature will not operate when the wiper switch is in the low or high speed position. • the rain sensing feature may not function properly when ice, or dried salt water is p...

  • Page 124

    Tilt steering column to tilt the column, push down on the lever below the turn signal control and move the wheel up or down, as desired. Pull the lever back towards you and firmly push the lever until it is above the lower surface of the shroud to lock the column in place. Warning! Tilting the steer...

  • Page 125

    Press the left side of the button to move the pedals rearward (toward the driver). Press the right side of the button to move the pedals forward (away from the driver). • the pedals can be adjusted with the ignition off. • the pedals can be adjusted while driving. • the pedals cannot be adjusted whe...

  • Page 126

    Caution! Do not place any article under the adjustable pedal’s or impede its ability to move as it may cause damage to the pedal controls. Pedal travel may become limited if movement is stopped by an obstruction in the adjustable pedal’s path. Electronic speed control when engaged, this device takes...

  • Page 127

    To set at a desired speed when the vehicle has reached the desired speed, press and release the set button. Release the accelerator and the vehicle will operate at the selected speed. To deactivate a soft tap on the brake pedal, normal braking, or pressing the cancel button will deactivate the speed...

  • Page 128

    To accelerate for passing depress the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed. Note: when driving uphill, at elevations above 2,000 feet (610 meters), or when the vehicle is heavily loaded (especially when towing) the vehicle may slow b...

  • Page 129

    Warning! To help keep your vehicle under control, do not use speed control under these conditions: • when it is not possible to keep your vehicle at a set speed. • on slippery roads, such as on snow or ice. • in heavy or varying traffic volume, in traffic that varies in speed, or on winding roads. •...

  • Page 130

    Warning! Abs (anti-lock brake system) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevail- ing road conditions. Abs cannot prevent accidents, including those resulting from excessive speed in turns, driving on very slippery surf...

  • Page 131

    Bas (brake assist system) the bas is designed to optimize the vehicle’s braking capability during emergency braking maneuvers. The system detects an emergency braking situation by sens- ing the rate and amount of brake application and then applies optimum pressure to the brakes. This can help reduce...

  • Page 132

    Erm (electronic roll mitigation) this system anticipates the potential for wheel lift by monitoring the driver’s steering wheel input and the speed of the vehicle. When erm determines that the rate of change of the steering wheel angle and vehicles speed are sufficient to potentially cause wheel lif...

  • Page 133

    Esp (electronic stability program) this system enhances directional control and stability of the vehicle under various driving conditions. Esp cor- rects for over/under steering of the vehicle by applying the brake of the appropriate wheel to assist in counter- acting the over/under steer condition....

  • Page 134

    Warning! Esp (electronic stability program) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions. Esp cannot prevent acci- dents, including those resulting from excessive speed in turns, driving on very slipper...

  • Page 135

    Or gravel conditions and more wheel spin than esp would normally allow is required to gain traction. To turn esp on again, momentarily depress the ⬙esp control switch ⬙. This will restore the normal “esp on” mode of operation. Note: to improve the vehicle’s traction when driving with snow chains, or...

  • Page 136

    In this mode, esp and tcs, except for the “limited slip” feature described in the tcs section, are turned off until the vehicle reaches a speed of 40 mph (64 km/h). At 40 mph (64 km/h) the system returns to “partial off” mode, described above. When the vehicle speed drops below 35 mph (56 km/h) the ...

  • Page 137

    40 mph (64 km/h). At 40 mph (64 km/h), the normal esp stability function returns but tcs remains off. When the vehicle speed drops below 35 mph (56 km/h), the esp system shuts off. Esp is off at low vehicle speeds in 4wd low range so that it will not interfere with off-road driving but esp function ...

  • Page 138

    If the “esp/bas warning lamp” comes on continuously with the engine running, a mal- function has been detected in either the esp or the bas system, or both. If this light remains on after several ignition cycles, and the vehicle has been driven several miles at speeds greater than 30 mph (48 km/h), ...

  • Page 139

    Rear park assist sensors the four rear park assist sensors, located in the rear fascia, monitor the area behind the vehicle that is within the sensors’ field of view. The monitored area seems oval in shape. The sensors can detect obstacles from approximately 11.8 inches (30 cm) up to 59 inches (150 ...

  • Page 140

    When the obstacle is detected at a distance of about 59 inches (150 cm) from the rear fascia, the outermost leds of the warning display will be on with increased bright- ness. Along with the led, a half second tone will occur. As the distance of the detected obstacle to the rear fascia decreases, mo...

  • Page 141

    When the switch is pressed to disable the system, the instrument cluster will display the ⬙park assist dis- abled ⬙ message. Refer to “electronic vehicle informa- tion center (evic)” in section 4 of this manual. When the shifter is changed to r (reverse) and the system is disabled, the instrument cl...

  • Page 142

    Cleaning the rear park assist system clean the rear park assist sensors with water, car wash soap and a soft cloth. Do not use rough or hard cloths. Do not scratch or poke the sensors. Otherwise, you could damage the sensors. Caution! • the rear park assist system is only a parking aid and it is una...

  • Page 143

    Warning! • drivers must be careful when backing up even when using the rear park assist system. Always check carefully behind your vehicle, look behind you, and be sure to check for pedestrians, animals, other vehicles, obstructions, and blind spots before back- ing up. You are responsible for safet...

  • Page 144

    Rear camera — if equipped vehicles with a navigation radio may be equipped with a rear view camera (located on the rear liftgate) that allows you to see an on-screen image (on the navigation radio screen) of the rear of your vehicle whenever the vehicle is put into r (reverse). Warning! Drivers must...

  • Page 145

    Turning the rear camera off 1. To turn the rear camera off, select “rear camera” at the systems settings screen and press enter. Refer to your “navigation user’s manual” for detailed operating instructions. 2. Select “off” at the “rear camera” screen. Highlight “done” and press enter. The rear camer...

  • Page 146

    The lights also turn on when a front door or rear door is opened. The lights will also turn on when the unlock button on the remote keyless entry transmitter is pressed. Sunglasses storage at the rear of the console a compartment is provided for the storage of a pair of sunglasses. The storage compa...

  • Page 147

    Warning! A moving garage door can cause injury to people and pets in the path of the door. People or pets could be seriously or fatally injured. Only use this transceiver with a garage door opener that has a “stop and reverse” feature as required by federal safety stan- dards. This includes most gar...

  • Page 148

    Programming homelink note: when programming a garage door opener, it is advised to park outside the garage. It is also recom- mended that a new battery be placed in the hand-held transmitter of the device being programmed to homelink for quicker training and accurate transmis- sion of the radio-freq...

  • Page 149

    2. Position the end of your hand-held transmitter 1-3 inches (3-8 cm) away from the homelink buttons. 3. Simultaneously press and hold both the homelink button that you want to train and the hand-held trans- mitter buttons. Do not release the buttons until step 4 has been completed. Note: some gate ...

  • Page 150

    Note: to program the remaining two homelink but- tons, begin with ⬙programming⬙ step two. Do not repeat step one. Note: if your hand-held transmitter appears to pro- gram the universal transceiver, but your garage door does not operate using the transmitter and your garage door opener was manufactur...

  • Page 151

    Canadian programming/gate programming canadian radio-frequency laws require transmitter sig- nals to ⬙time-out⬙ (or quit) after several seconds of transmission which may not be long enough for homelink to pick up the signal during programming. Similar to this canadian law, some u.S. Gate operators a...

  • Page 152

    • press and hold the two outer homelink buttons and release only when the evic display shows “chan- nels cleared” (after 20 seconds). Release both buttons. Do not hold for longer that 30 seconds. Homelink is now in the train (or learning) mode and can be programmed at any time beginning with ⬙pro- g...

  • Page 153

    Homelink 威 is a trademark owned by johnson controls, inc. Power sunroof — if equipped the power sunroof switch is located between the sun visors on the overhead console. Warning! • never leave children in a vehicle, with the keys in the ignition switch. Occupants, particularly unat- tended children,...

  • Page 154

    Opening sunroof - express press the switch rearward and release, and the sunroof will open automatically from any position. The sunroof will open fully, then stop automatically. This is called express open. During express open operation, any movement of the sunroof switch will stop the sunroof. Clos...

  • Page 155

    Sunshade operation the sunshade can be opened manually. However, the sunshade will open automatically as the sunroof opens. Note: the sunshade cannot be closed if the sunroof is open. Wind buffeting wind buffeting can be described as the perception of pressure on the ears or a helicopter type sound ...

  • Page 156

    Power outlet to the right of the convenience tray (lower center of instrument panel) is an outlet for electrically powered accessories. Pull lightly on the tab of the plastic cover to access the outlet. The rear power outlet (if equipped) is located in the left rear cargo area. The power outlets are...

  • Page 157

    All accessories connected to this outlet should be re- moved or turned off when the vehicle is not in use to protect the battery against discharge. Caution! Electrical outlet use with engine off • many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i....

  • Page 158

    Cup holders in the center console there are two cup holders for the front seat passengers. Note: the cup holder insert is removable, from the console, for cleaning. It can be reinstalled with the larger cup depression towards the passenger seat, but the top surface will not be flush with the console...

  • Page 159

    Cargo area features cargo light the cargo area light is activated by opening the liftgate, opening any door, or by rotating the dimmer control on the multi-function control lever to the extreme top posi- tion. If all doors are closed and only the liftgate is open, pushing on the cargo light lens sur...

  • Page 160

    Retractable cargo area cover — if equipped note: the purpose of this cover is for privacy, not to secure loads. It will not prevent cargo from shifting or protect passengers from loose cargo. To cover the cargo area: 1. Grasp the cover at the center handle. Pull it over the cargo area. 2. Insert the...

  • Page 161

    Warning! In an accident a cargo cover loose in the vehicle could cause injury. It could fly around in a sudden stop and strike someone in the vehicle. Do not store the cargo cover on the cargo floor or in the passenger compartment. Remove the cover from the vehicle when taken from its mounting. Do n...

  • Page 162

    Warning! Cargo tie-down hooks are not safe anchors for a child seat tether strap. In a sudden stop or collision a hook could pull loose and allow the child seat to come loose. A child could be badly injured. Use only the anchors provided for child seat tethers. Warning! The weight and position of ca...

  • Page 163

    Warning! To help protect against personal injury, passengers should not be seated in the rear cargo area. The rear cargo space is intended for load carrying purposes only, not for passengers, who should sit in seats and use seat belts. Cargo load floor the panel in the load floor is reversible for a...

  • Page 164

    1. Flip up pull loop(s) so they are perpendicular (straight up) to the top surface of the tray. 2. Pull up on loop(s) and twist 90 degrees, so they are parallel to the slotted hole in tray. 3. Lift tray over loop(s), and reposition tray. 4. Pull up on loop(s) and twist 90 degrees, so they are perpen...

  • Page 165

    If the liftgate flipper glass is open, connection to the rear window wiper is interrupted preventing activation of the rear wiper blade. When the liftgate flipper glass is closed, the rear wiper switch or the ignition switch needs to be turned off and on to restart the rear wiper. Adding washer flui...

  • Page 166

    Roof luggage rack — if equipped external racks do not increase the total load carrying capacity of the vehicle. Be sure that the total occupant and luggage load inside the vehicle, plus the load on the luggage rack, do not exceed the rated vehicle capacity. This vehicle is not equipped with roof rac...

  • Page 167

    Caution! • to prevent damage to the roof of your vehicle, do not carry any loads on the roof rack without cross rails in- stalled. The load should be secured and placed on top of the cross rails, not directly on the roof. If it is necessary to place the load on the roof, place a blanket or some othe...

  • Page 169: Contents

    Understanding your instrument panel contents 䡵 instrument panel and controls . . . . . . . . . . . . . 172 䡵 instrument cluster . . . . . . . . . . . . . . . . . . . . . . 173 ▫ gasoline engine . . . . . . . . . . . . . . . . . . . . . . 173 ▫ diesel engine . . . . . . . . . . . . . . . . . . . . . ...

  • Page 170

    䡵 sales code raq – am/fm/cd (6-disc) radio with optional satellite radio, hands free phone, and vehicle entertainment systems (ves) capabilities . . . . . . . . . . . . . . . . . . . . . . . . . . . 199 ▫ operating instructions - radio mode . . . . . . . 199 ▫ operation instructions - (cd mode for c...

  • Page 171

    䡵 satellite radio — if equipped . . . . . . . . . . . . . . 226 ▫ system activation . . . . . . . . . . . . . . . . . . . . . 227 ▫ electronic serial number/sirius identification number (esn/sid) . . . . . . . . . . . . . . . . . . . . 227 ▫ selecting satellite mode in ref radios . . . . . . 228 ▫ s...

  • Page 172

    Instrument panel and controls 172 understanding your instrument panel.

  • Page 173

    Instrument cluster gasoline engine understanding your instrument panel 173 4.

  • Page 174

    Diesel engine 174 understanding your instrument panel.

  • Page 175

    Instrument cluster description 1. Speedometer indicates vehicle speed. 2. Brake warning light the brake warning light will come on when the ignition is first turned on, and stay on briefly as a bulb check. If the bulb does not come on during starting, have the bulb re- paired promptly. If the light ...

  • Page 176

    Engine start. If the bulb does not come on when turning the key from off to on, have the condition checked promptly. Certain conditions such as a loose or missing gas cap, poor fuel quality, etc. May illuminate the light after engine start. The vehicle should be serviced if the light stays on throug...

  • Page 177

    8. Tachometer the red segments indicate the maximum permissible engine revolutions-per-minute (r.P.M. X 1000) for each gear range. Before reaching the red area, ease up on the accelerator. 9. Security alarm system indicator light — if equipped this light will flash rapidly for approximately 15 secon...

  • Page 178

    12. Tire pressure monitoring telltale light each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. (if your vehicle has tires of a differ...

  • Page 179

    Caution! The tpms has been optimized for the original equipment tires and wheels. Tpms pressures and warnings have been established for the tire size equipped on your vehicle. Undesirable system op- eration or sensor damage may result when using replacement equipment that is not of the same size, ty...

  • Page 180

    Warning! A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant. If you decide to look under the hood your- self, refer to section 7 of this manual. Follow the warnings under “cooling system pressure cap.” 14. Electronic vehicle information center d...

  • Page 181

    18. Seat belt reminder light when the ignition switch is first turned on, this light will turn on for 5 to 8 seconds as a bulb check. During the bulb check, if the driver’s seat belt is unbuckled, a chime will sound. After the bulb check or when driving, if the driver or front passenger seat belt re...

  • Page 182

    Is placed in the p (park) position. The light should turn off. If the light remains lit with the engine running your vehicle will usually be drivable, however, see your dealer for service as soon as possible. If the light is flashing when the engine is running, immediate service is re- quired and yo...

  • Page 183

    Electronic vehicle information center — if equipped the electronic vehicle information center (evic) located in the instrument cluster, when the appropriate condi- tions exist, will display the following messages and symbols. Some of the messages are accompanied by a chime. • turn signal on • perfor...

  • Page 184

    • liftgate/door open (with graphic) • liftgate/doors open (with graphic) • liftglass open (with graphic) • hood open (with graphic) • hood/door open (with graphic) • hood/doors open (with graphic) • liftgate/hood open (with graphic) • hood/glass/door open (with graphic) • hood/glass/doors open (with...

  • Page 185

    • check gas cap • esp off • memory #1 positions set • memory #2 positions set • memory system disabled — seatbelt fas- tened (with graphic) • memory system disabled — vehicle not in park • driver 1 memory • driver 2 memory • pedal adjust disabled — cruise control set • pedal adjust disabled — shifte...

  • Page 186

    Customer programmable features press the menu button until one of the display choices following appears: language? When in this display you may select one of three lan- guages for all display nomenclature, including the trip computer functions. Press the step button while in this display selects eng...

  • Page 187

    Display u.S. Or metric? Pressing the step button when in this display selects us or metric. The overhead console and instrument panel displays will be in the selected units. Auto door locks? When this feature is selected, all doors and the liftgate lock automatically when the speed of the vehicle re...

  • Page 188

    Remote linked to memory? (available with memory seat only) when this feature is selected the memory seat, mirror, and radio settings will return to the memory set position when the remote keyless entry “unlock” button is pressed. If this feature is not selected then the memory seat, mirror, and radi...

  • Page 189

    Illuminated approach? When this feature is selected the driver can choose, when entering the vehicle, to have the headlamps come on for 30, 60, or 90 seconds, or not come on at all. Pressing the step button when in this display will select 30, 60, 90, or off. Auto headlamp low/high beams? (available...

  • Page 190

    Service interval gasoline models — if equipped when this feature is selected, a service interval between 2,000 (3 200 km) and 6,000 miles (10 000 km) in 500 mile (800 km) increments may be selected. Pressing the step button when in this display will select distances between 2,000 (3 200 km) and 6,00...

  • Page 191

    Link to memory is set to yes) when the remote keyless entry transmitter is used to unlock the door. For more information, refer to “easy entry/exit seat — driver memory seat” in section 3 of this manual. (see page 110 for more information.) compass/temperature/trip computer this display provides the...

  • Page 192

    Warning! Even if the display still reads a few degrees above 32°f ( 0°c), the road surface may be icy, particularly in woods or on bridges. Drive carefully under such conditions to prevent an accident and possible per- sonal injury or property damage. Compass/temperature display 192 understanding yo...

  • Page 193

    Trip computer this feature, located in the instrument cluster, displays the following information when the display is in the “compass/temperature” mode and the step button is pressed: step button press the step button to cycle through all of the compass/mini-trip computer displays. Step button under...

  • Page 194

    Reset button press the reset button to reset the display you are in. Press and hold the reset button (for 2 seconds) to reset all of the displays. Average fuel economy shows the average fuel economy since the last reset. When the fuel economy is reset, the display will read “reset” or show dashes fo...

  • Page 195

    Elapsed time shows the accumulated ignition on time since the last reset. Tire pressure display — if equipped shows the current pressure of all 4 road tires. Note: tires heat up during normal driving conditions. Heat will cause the tire pressure to increase from 2 to 6 psi (14 to 41 kpa) during norm...

  • Page 196

    Note: to ensure proper compass calibration, make sure the compass variance is properly set before manu- ally calibrating the compass. Refer to variance map. To put into a calibration mode start the engine and leave the transmission in the p (park) position. Set the display to “compass/temperature.” ...

  • Page 197

    To set the variance: turn the ignition on and set the display to “compass/temperature.” press the c/t but- ton for approximately 5 seconds. The last variance zone number will be displayed. Press and hold the step button for 1 second to select the new variance zone and press the reset button to resum...

  • Page 198

    Two types of signals there are two basic types of radio signals... Am or amplitude modulation, in which the transmitted sound causes the amplitude, or height, of the radio waves to vary... And fm or frequency modulation, in which the frequency of the wave is varied to carry the sound. Electrical dis...

  • Page 199

    Sales code raq – am/fm/cd (6-disc) radio with optional satellite radio, hands free phone, and vehicle entertainment systems (ves) capabilities note: the radio sales code is located on the lower right side of your radio faceplate. Operating instructions - radio mode note: the ignition switch must be ...

  • Page 200

    Mode button (radio mode) press the mode button repeatedly to select between the cd player, satellite radio, or vehicle entertainment system (ves) (if equipped). Seek button (radio mode) press and release the seek button to search for the next listenable station in either am/fm or satellite (if equip...

  • Page 201

    Time button press the time button and the time of day will be displayed for 5 seconds. Clock setting procedure 1. Press and hold the time button until the hours blink. 2. Adjust the hours by turning the right side tune / audio control. 3. After the hours are adjusted, press the right side tune / aud...

  • Page 202

    Press the rotary tune control a third time and treble will display. Turn the tune control to the right or left to increase or decrease the treble tones. Press the rotary tune control a fourth time and bal- ance will display. Turn the tune control to the right or left to adjust the sound level from t...

  • Page 203

    Jazz jazz news news nostalgia nostalgia oldies oldies personality personality public public rhythm and blues rhythm_and_blues religious music religious_music religious talk religious_talk rock rock soft soft soft rock soft_rock soft rhythm and blues soft_r_&_b sports sports talk talk top 40 top_40 w...

  • Page 204

    You may add a second station to each push-button by repeating the above procedure with this exception: press the set/dir button twice and set 2 will show in the display window. Each button can be set for set 1 and set 2 in both am and fm. This allows a total of 12 am,12 fm and 12 satellite (if equip...

  • Page 205

    Caution! This cd player will accept 4 3/4 inch (12 cm) discs only. The use of other sized discs may damage the cd player mechanism. You may eject a disc with the radio off. If you insert a disc with the ignition on and the radio on, the unit will switch from radio to cd mode and begin to play when y...

  • Page 206

    Load/eject button (cd mode for cd audio play) load/ eject - load press the load/ eject button and the push- button with the corresponding number where the cd is being loaded. The radio will display please wait and prompt when to insert disc. After the radio displays ⬙load disc⬙ insert the cd into th...

  • Page 207

    Time button (cd mode for cd audio play) press this button to change the display from a large cd playing time display to a small cd playing time display. Rw/ff (cd mode for cd audio play) press and hold ff (fast forward) and the cd player will begin to fast forward until ff is released or rw or anoth...

  • Page 208

    Notes on playing mp3 files the radio can play mp3 files, however, acceptable mp3 file recording media and formats are limited. When writing mp3 files, pay attention to the following restric- tions. Supported media (disc types) the mp3 file recording media supported by the radio are cd-rom, cd-r and ...

  • Page 209

    Supported mp3 file formats the radio will recognize only files with the *.Mp3 exten- sion as mp3 files. Non-mp3 files named with the *.Mp3 extension may cause playback problems. The radio is designed to recognize the file as an invalid mp3 and will not play the file. When using the mp3 encoder to co...

  • Page 210

    Id3 tag information for artist, song title and album title are supported for version 1 id3 tags. Id3 version 2 is not supported by the radios. Playlist files are not supported. Mp3 pro files are not supported. Playback of mp3 files when a medium containing mp3 data is loaded, the radio checks all fi...

  • Page 211

    Load/eject button (cd mode for mp3 play) load/ eject - load press the load/ eject button and the push- button with the corresponding number where the cd is being loaded. The radio will display please wait and prompt when to insert disc. After the radio displays ⬙load disc⬙ insert the cd into the pla...

  • Page 212

    Press and hold the msg or info button while in the message display priority mode or elapsed time display priority mode will display the song title for each file. Rw/ff (cd mode for mp3 play) press the ff side of the button to move forward through the mp3 selection. Tune control (cd mode for mp3 play...

  • Page 213

    Sales code ref — am/fm/cd (single disc) radio with optional satellite radio and hands free phone capability note: the radio sales code is located on the lower right side of your radio faceplate. Operating instructions - radio mode note: the ignition switch must be in the on or acc position to operat...

  • Page 214

    Mode button (radio mode) press the mode button repeatedly to select between the cd player and satellite radio (if equipped). Seek button (radio mode) press and release the seek button to search for the next listenable station in either am/fm or satellite (if equipped) mode. Press the right side of t...

  • Page 215

    Clock setting procedure 1. Press and hold the time button until the hours blink. 2. Adjust the hours by turning the right side tune/ audio control. 3. After the hours are adjusted, press the right side tune/audio control to set the minutes. The minutes will begin to blink. 4. Adjust the minutes usin...

  • Page 216

    Press the rotary tune control a fourth time and bal will display. Turn the tune control to the right or left to adjust the sound level from the right or left side speakers. Press the rotary tune control a fifth time and fade will display. Turn the tune control to the left or right to adjust the soun...

  • Page 217

    Operation instructions - cd mode note: the ignition switch must be in the on or acc position to operate the radio. Inserting the compact disc (single cd player) gently insert one cd into the cd player with the cd label facing up. The cd will automatically be pulled into the cd player and the cd icon...

  • Page 218

    Scan button (cd mode) press this button to play the first 10 seconds of each track. To stop the scan function, press the button a second time. Eject button (cd mode) press this button and the disc will unload and move to the entrance for easy removal. The unit will switch to the last selected mode. ...

  • Page 219

    Operation instructions - auxiliary mode the auxiliary (aux) jack is an audio input jack, which allows the user to plug in a portable device such as an mp3 player, cassette player, or microphone and utilize the vehicle’s audio system to amplify the source and play through the vehicle speakers. The au...

  • Page 220

    Time button (auxiliary mode) press this button to change the display from elapsed playing time to time of day. The time of day will display for 5 seconds. Rw/ff (auxiliary mode) no function. Rnd/set button (auxiliary mode) no function. Mode button (auxiliary mode) press the mode button repeatedly to...

  • Page 221

    Satellite navigation radio with cd player with mp3 capability (rec) - combines a global-positioning system-based navigation system with an integrated color screen to provide maps, turn identification, selection menus and instructions for selecting a variety of destina- tions and routes, am/fm stereo...

  • Page 222

    1. At the main menu screen, highlight “clock setup” and press enter or press and hold for 3 seconds the time button on the unit’s faceplate. The clock setup screen appears. 2. To show the gps clock, select “displayed clock: gps clock” and press enter. 3. To adjust the time zone, select “time zone” a...

  • Page 223

    2. To increase the clock by hours, make sure “hr +” is highlighted and press enter. Press enter again to increase the clock by another hour. You will see on the “user defined time” display the number of hours you have increased the clock by. 3. To decrease the clock by one hour, use the select encod...

  • Page 224

    1. When you are at an audio screen, quickly press the time button on the navigation faceplate. 2. In this example the large clock appears on the screen. 3. To switch the clock to the small clock, quickly press time again. 4. To toggle back to the large clock, simply press time. 224 understanding you...

  • Page 225

    Video entertainment system (sales code xrv) — if equipped the optional ves™ (video entertainment system) con- sists of a dvd player and lcd (liquid crystal display) screen, a battery-powered remote control, and two head- sets. The dvd player is mounted in the rear of the center console storage bin, ...

  • Page 226

    The lcd screen is located on the headliner behind the front seats. Satellite radio — if equipped satellite radio uses direct satellite to receiver broadcast- ing technology to provide clear digital sound, coast to coast. The subscription service provider is sirius™ satel- lite radio. This service of...

  • Page 227

    Sports, news, entertainment, and programming for chil- dren, directly from its satellites and broadcasting studios. System activation to activate your sirius satellite radio service, call the toll-free number 888-539-7474, or visit the sirius web site at www.Sirius.Com. Please have the following inf...

  • Page 228

    Esn/sid access with raq radios with the ignition switch in the accessory position and the radio off, press the cd eject and time buttons simultaneously for 3 seconds. All twelve esn/sid num- bers will be displayed. The radio will exit the esn/sid mode when any other button is pushed, the ignition is...

  • Page 229

    Appear in the display between each channel change. Press the scan button a second time to stop the search. Note: channels that may contain objectionable content can be blocked. Contact sirius customer care at 888-539- 7474 to discuss options for channel blocking or unblock- ing. Please have your esn...

  • Page 230

    Satellite antenna to ensure optimum reception on vehicles available with a luggage rack, do not place items on the roof around the rooftop antenna location. Metal objects placed within the line of sight of the antenna will cause decreased perfor- mance. Larger luggage items should be placed as far f...

  • Page 231

    The right hand control is a rocker type switch with a push-button in the center and controls the volume and mode of the sound system. Pressing the top of the rocker switch will increase the volume and pressing the bottom of the rocker switch will decrease the volume. Pressing the center button will ...

  • Page 232

    The center button on the left side rocker switch has no function for a single disc cd player. However, when a multiple disc cd player is equipped on the vehicle, the center button will select the next available cd in the player. Cd/dvd disc maintenance to keep the cd/dvd discs in good condition, tak...

  • Page 233

    Climate controls manual air conditioning and heating system — if equipped the controls for the heating/air conditioning and venti- lation system in this vehicle consist of a series of rotary knobs. These comfort controls can be set to obtain desired interior conditions. The instrument panel features...

  • Page 234

    Temperature control the temperature of air can be selected by rotating the temperature control knob in the center. The coldest tem- perature setting is on the extreme left and the warmest setting on the ex- treme right of the rotation. The knob can be positioned at any point on the dial. Mode contro...

  • Page 235

    Through vents under the front seats. Some airflow is delivered to defrost while in the floor mode so that comfort can be maintained. Bi-level air flows both through the outlets located in the instrument panel and those located on the floor. Air flows through the registers in the back of the center c...

  • Page 236

    Slight changes in engine speed or power may be noticed when the air conditioning compressor is on. This is a normal occurrence as the compressor will cycle on and off to maintain comfort and increase fuel economy. Automatic temperature control — if equipped the infrared dual-zone climate control sys...

  • Page 237

    Lo auto position should be used for front seat occu- pants only. The hi auto position should be used when more air flow is desired, or when rear seat occupants are present. Dial in the comfort setting you would like the system to maintain by rotating the driver’s or passenger’s control knob. Once th...

  • Page 238

    Debris due to the climate control sensor’s location. Mud on the windshield may also cause poor operation of this system. • to provide you with maximum comfort in the auto- matic mode, during cold start-ups the blower fan will remain off until the engine warms up. However, the fan will engage immedia...

  • Page 239

    Understanding your instrument panel 239 4.

  • Page 240

    Note: regardless of the type of operation, when a temperature knob is set to the full clockwise or full counterclockwise position, the system will deliver full hot or full cold air out of the ducts, respectively. The operator can override the auto mode setting and select the direction of the air by ...

  • Page 241

    • bi-level air flows both through the outlets located in the instrument panel and those located on the floor. Air flows through the registers in the back of the center console, and under the front seats to the rear seat passengers. These registers can be closed to block airflow. The center console o...

  • Page 242

    Note: extended use of recirculation may cause the windows to fog. If the interior of the windows begins to fog, press the “recirculate” icon button to return to outside air. Some temp./humidity conditions will cause captured interior air to condense on windows and ham- per visibility. For this reaso...

  • Page 243

    When using the air conditioner in extremely heavy traffic in hot weather especially when towing a trailer, addi- tional engine cooling may be required. If this situation is encountered, operate the transmission in a lower gear to increase engine rpm, coolant flow and fan speed. When stopped in heavy...

  • Page 244

    Operating tips chart 244 understanding your instrument panel.

  • Page 245: Starting And Operating

    Starting and operating contents 䡵 starting procedure . . . . . . . . . . . . . . . . . . . . . . 249 ▫ normal starting — gasoline engines . . . . . . . 249 ▫ if engine fails to start . . . . . . . . . . . . . . . . . 249 ▫ normal starting — diesel engines . . . . . . . . . 250 䡵 engine block heater ...

  • Page 246

    䡵 off-road driving tips . . . . . . . . . . . . . . . . . . . 268 ▫ when to use 4wd low range — if equipped . . . . . . . . . . . . . . . . . . . . . . . . . 268 ▫ driving through water . . . . . . . . . . . . . . . . . 268 ▫ driving in snow, mud and sand . . . . . . . . . . 270 ▫ hill climbing . . ...

  • Page 247

    ▫ alignment and balance . . . . . . . . . . . . . . . . . 293 䡵 tire chains . . . . . . . . . . . . . . . . . . . . . . . . . . . 294 䡵 tire rotation recommendations . . . . . . . . . . . . 294 䡵 tire pressure monitor system (tpms) . . . . . . . . 295 ▫ base system — if equipped . . . . . . . . . . ...

  • Page 248

    䡵 fuel requirements — diesel . . . . . . . . . . . . . . . 312 䡵 adding fuel . . . . . . . . . . . . . . . . . . . . . . . . . . 313 ▫ fuel filler cap (gas cap) . . . . . . . . . . . . . . . 313 䡵 vehicle loading . . . . . . . . . . . . . . . . . . . . . . . . 316 ▫ certification label . . . . . . ....

  • Page 249

    Starting procedure start the engine with the selector lever in the n (neutral) or p (park) position. Apply the brake before shifting to any driving range. Normal starting — gasoline engines do not press the accelerator. Turn the ignition key briefly to start position, and release it. The starter mot...

  • Page 250

    If the engine shows no sign of starting after two 15 second periods of cranking with the accelerator pedal held to the floor, the normal starting procedure should be repeated. Warning! Never pour fuel or other flammable liquids into the throttle body air inlet opening in an attempt to start the vehi...

  • Page 251

    Starting and operating cautions — diesel engines warning! Never pour fuel or other flammable liquid into the air inlet opening in an attempt to start the vehicle. This could result in a flash fire causing serious personal injury. • running a cold engine at high speeds during driving or idling may da...

  • Page 252

    Turbocharger ⬙cool down⬙ chart driving conditions load turbocharger temperature idle time (in minutes) before shut down stop & go empty cool less than 1 stop & go medium warm 1 highway speeds medium warm 2 city traffic max. Gcwr warm 3 highway speeds max. Gcwr warm 4 uphill grade max. Gcwr hot 5 252...

  • Page 253

    Engine block heater — if equipped the engine block heater warms engine coolant and per- mits quicker starts in cold weather. Connect the cord to a standard 110-115 volt ac electrical outlet with grounded, three wire extension cord. Use the heater when temperatures below 0°f (-18°c) are expected to l...

  • Page 254

    Warning! It is dangerous to shift the selector lever out of p (park) or n (neutral) if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in reverse. You could lose control of the vehicle and hit someone or somet...

  • Page 255

    Gear ranges note: after selecting any gear range, wait a moment to allow the selected gear to engage before accelerating. This is especially important when the engine is cold. If there is a need to restart the engine be sure to cycle the key to the lock position before restarting. Transmission gear ...

  • Page 256

    Warning! It is dangerous to shift the selector lever out of p (park) or n (neutral) if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in reverse. You could lose control of the vehicle and hit someone or somet...

  • Page 257

    Of the desired top gear. For example, if the driver shifts the transmission into 3 (third gear), the transmission will never shift above third gear, but can shift down to 2 (second) or 1 (first), when needed. On vehicles equipped with 4.7l or 5.7l engines, use of ers (or tow/haul mode) also enables ...

  • Page 258

    Overdrive operation the automatic transmission includes an electronically controlled overdrive (5th gear for 3.7l engine, 4th and 5th gears for 4.7l and 5.7l engines). The transmission will automatically shift from direct gear to overdrive if the following conditions are present: • the transmission ...

  • Page 259

    In high ambient temperatures with sustained high engine speed and load, an upshift followed shortly thereafter by a downshift may occur. This is a normal part of the overheat protection strategy when operating in the “tow/haul” mode. The transmission will downshift from overdrive to the most desirab...

  • Page 260

    Transmission limp home mode transmission function is monitored for abnormal condi- tions. If a condition is detected that could result in transmission damage, the transmission limp home mode will be engaged. In this mode, the transmission will remain in the current gear (3.7l engine) or in direct ge...

  • Page 261

    Note: the torque converter clutch will not engage until the transmission fluid and engine coolant are warm [usually after 1-3 miles (1.6 - 4.8 km) of driving]. Because the engine speed is higher when the torque converter clutch is not engaged, it may seem as if the transmission is not shifting into ...

  • Page 262

    Five rocking-motion cycles. This will minimize overheat- ing and reduce the risk of transmission failure during prolonged efforts to free a stuck vehicle. Caution! When “rocking” a stuck vehicle by moving between “first” and r (reverse), do not spin the wheels faster than 15 mph (24 km/h), or drivet...

  • Page 263

    Percent of engine torque to the rear axle. When speed differences are increased between the front and rear drive shafts, the transfer case can transmit up to 100 percent of available engine torque to the front or rear drive shafts. When additional traction is required, the 4 low position can be used...

  • Page 264

    Warning! You or others could be injured if you leave the vehicle unattended with the transfer case in the n (neutral) position without first fully engaging the parking brake. The transfer case n (neutral) position disengages both the front and rear driveshafts from the powertrain and will allow the ...

  • Page 265

    Low indicator lamp” in the instrument cluster will begin to flash and remain on solid when the shift is complete. Release the t-handle. Note: if shift conditions/interlocks are not met, or a transfer case motor temperature protection condition exists, a “check shift procedures” message will flash fr...

  • Page 266

    Low indicator lamp” in the instrument cluster will flash and go out when the shift is complete. Release the t-handle. Note: if shift conditions/interlocks are not met, or a transfer case motor temperature protection condition exists, a “check shift procedures” message will flash from the evic (elect...

  • Page 267

    5. Repeat steps 1– 4 to shift out of neutral. Note: if shift conditions/interlocks are not met, a “check shift procedures” message will flash from the evic (electronic vehicle information center). Refer to “electronic vehicle information center (evic)” in section 4 of this manual. (see page 183 for ...

  • Page 268

    Operation is similar. Follow the quadra-trac ii 威 transfer case shifting information, preceding this section, for shifting this system. On-road driving tips utility vehicles have higher ground clearance and a narrower track to make them capable of performing in a wide variety of off-road application...

  • Page 269

    Caution! When driving through water, do not exceed 5 mph (8 km/h). Always check water depth before entering as a precaution, and check all fluids afterward. Driving through water may cause damage that may not be covered by the new vehicle limited warranty. Driving through water more than a few inche...

  • Page 270

    Driving in snow, mud and sand in heavy snow, when pulling a load, or for additional control at slower speeds, shift the transmission to a low gear and shift the transfer case to 4wd low if necessary. Refer to “four-wheel drive operation” in this section. Do not shift to a lower gear than necessary t...

  • Page 271

    Remember, never drive diagonally across a hill-always drive straight up or down. If the wheels start to slip as you approach the crest of a hill, ease off the accelerator and maintain headway by turning the front wheels slowly. This may provide a fresh “bite” into the surface and will usually provid...

  • Page 272

    • after extended operation in mud, sand, water, or similar dirty conditions, have brake rotors, wheels, brake linings, and axle yokes inspected and cleaned as soon as possible. Warning! Abrasive material in any part of the brakes may cause excessive wear or unpredictable braking. You might not have ...

  • Page 273

    Be sure the parking brake is firmly set when parked and the gear shift lever is in the p (park) position. When parking on a hill, you should apply the parking brake before placing the gear shift lever in p (park), otherwise the load on the transmission locking mechanism may make it difficult to move...

  • Page 274

    When parking on a hill, turn the front wheels toward the curb on a downhill grade and away from the curb on an uphill grade. The parking brake should always be applied whenever the driver is not in the vehicle. Anti-lock brake system the anti-lock brake system (abs) is designed to aid the driver in ...

  • Page 275

    Warning! Pumping of the anti-lock brakes will diminish their effectiveness and may lead to an accident. Pumping makes the stopping distance longer. Just press firmly on your brake pedal when you need to slow down or stop. Warning! • the anti-lock brake system (abs) cannot pre- vent the natural laws ...

  • Page 276

    Caution! The anti-lock brake system is subject to possible detrimental effects of electronic interference caused by improperly installed after-market radios or tele- phones. Note: during severe braking conditions, a pulsing sensation may occur and a clicking noise will be heard. This is normal, indi...

  • Page 277

    Build up between the tire tread and the road. This hydroplaning action can cause loss of traction, braking ability, and control. • after going through deep water or a car wash, brakes may become wet, resulting in decreased performance and unpredictable braking action. Dry the brakes by gentle, inter...

  • Page 278

    Caution! Prolonged operation of the steering system at the end of the steering wheel travel will increase the steering fluid temperature and it should be avoided when possible. Damage to the power steering pump may occur. Multi displacement system (mds) - 5.7l engine only this feature offers improve...

  • Page 279

    • european metric tire sizing is based on european design standards. Tires designed to this standard have the tire size molded into the sidewall beginning with the section width. The letter ⬙p⬙ is absent from this tire size designation. Example: 215/65r15 96h • lt (light truck)-metric tire sizing is...

  • Page 280

    Tire sizing chart example: size designation: p = passenger car tire size based on u.S. Design standards ⴖ....Blank....ⴖ = passenger car tire based on european design standards lt = light truck tire based on u.S. Design standards t = temporary spare tire 31 = overall diameter in inches (in) 215 = sec...

  • Page 281

    Example: service description: 95 = load index —a numerical code associated with the maximum load a tire can carry. H = speed symbol —a symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions. —the maximum speed corresp...

  • Page 282

    Tire identification number (tin) the tin may be found on one or both sides of the tire; however, the date code may only be on one side. Tires with white sidewalls will have the full tin including date code located on the white sidewall side of the tire. Look for the tin on the outboard side of black...

  • Page 283

    Tire loading and tire pressure tire placard location note: the proper cold tire inflation pressure is listed on either the face of the driver’s door or the driver’s side “b” pillar. Tire and loading information placard this placard tells you important information about the: 1) number of people that ...

  • Page 284

    Loading the vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size, and cold tire inflation pressures specified on the “tire and loading informat...

  • Page 285

    5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in step 4. 6. If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. Consult th...

  • Page 286

    286 starting and operating.

  • Page 287

    Warning! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. Tires — general information tire pressure proper tire inflation pressur...

  • Page 288

    2. Economy— improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Under inflation also increases tire rolling resistance and results in higher fuel consump- t...

  • Page 289

    Check tire pressure. Do not make a visual judgement when determining proper inflation. Radial tires may look properly inflated even when they are under inflated. Caution! After inspecting or adjusting the tire pressure al- ways reinstall the valve stem cap–if equipped. This will prevent moisture and...

  • Page 290

    Tire pressures for high speed operation the manufacturer advocates driving at safe speeds within posted speed limits. Where speed limits or condi- tions are such that the vehicle can be driven at high speeds, maintaining correct tire inflation pressure is very important. Increased tire pressure and ...

  • Page 291

    Warning! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause tire dam- age or failure. A tire could explode and injure someone. Do not spin your vehicle’s wheels faster than 35 mph (55 km/h) when you are stuck, and do not let anyone near a spinning wheel no m...

  • Page 292

    Life of tire the service life of a tire is dependent upon varying factors including but not limited to: • driving style • tire pressure • distance driven warning! Tires and spare tire should be replaced after six years, regardless of the remaining tread. Failure to follow this warning can result in ...

  • Page 293

    Warning! • do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change suspen- sion dimensions and performance characteristics, resulting in changes to steering, handling, and brak- ing of your vehicle. This can caus...

  • Page 294

    Improper alignment will not cause vehicle vibration. Vibration may be a result of tire and wheel out-of- balance. Proper balancing will reduce vibration and avoid tire cupping and spotty wear. Tire chains certain models have sufficient tire-to-body clearance to allow use of tire chains. Install chai...

  • Page 295

    Follow the recommended tire rotation frequency for your type of driving found in the “maintenance schedules” section of this manual. More frequent rotation is permis- sible if desired. The reasons for any rapid or unusual wear should be corrected prior to rotation being per- formed. Note: the premiu...

  • Page 296

    Decrease. Tire pressure should always be set based on cold inflation tire pressure. This is defined as the tire pressure after a vehicle has not been driven for more than 3 hours - and in outside ambient temperature. Refer to the “tires – general information” in this section for information on how t...

  • Page 297

    Telltale light” will turn off only after the tires have been inflated to the vehicle’s recommended cold tire pressure value. Note: seasonal temperature changes will affect tire pressure, and the tpm system will monitor the actual tire pressure in the tire. Base system — if equipped the tire pressure...

  • Page 298

    Will automatically update and the “tire pressure moni- toring light” will extinguish once the updated tire pres- sures have been received. The vehicle may need to be driven for up to 10 minutes above 15 mph (24 km/h) to receive this information. A low spare tire will not cause the “tire pressure mon...

  • Page 299

    Will update automatically, and the “tire pressure moni- toring telltale light” will be off as long as none of the road tires are below the low pressure warning threshold. The vehicle may need to be driven for up to 10 minutes above 15 mph (24 km/h) to receive this information. Caution! The tpms has ...

  • Page 300

    Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability. • the tpms is not a substitute for proper tire mainte- nance, and it is the driver’s responsibility to maintain correct tire pressure, even if under-inflation has not reached...

  • Page 301

    Tire pressure monitoring low pressure warnings the “tire pressure monitoring telltale light” will illuminate in the instrument cluster, and an au- dible chime will be activated when one or more of the four active road tire pressures are low. The audible chime will sound once every ignition cycle for...

  • Page 302

    Should a low tire condition occur on any of the four active road tire(s), you should stop as soon as possible, and inflate the low tire(s) that is flashing on the graphic display to the vehicle’s recommended cold tire pressure. The system will automatically update, the graphic dis- play of the press...

  • Page 303

    If the ignition key is cycled, this sequence will repeat, providing the system fault still exists. If the system fault no longer exists, the “tire pressure monitoring telltale light” will no longer flash, the ⬙service tire press. System ⬙ text message will no longer display, and a pressure value wil...

  • Page 304

    Telltale light” will be off as long as no road tire(s) are below the low pressure warning threshold. The vehicle may need to be driven for up to 10 minutes above 15 mph (24 km/h) to receive this information. Caution! The tpms has been optimized for the original equipment tires and wheels. Tpms press...

  • Page 305

    Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability. • the tpms is not a substitute for proper tire mainte- nance, and it is the driver’s responsibility to maintain correct tire pressure, even if under-inflation has not reached...

  • Page 306

    5.7l engines (if equipped) the 5.7l engine is designed to meet all emissions regulations and provide satisfac- tory fuel economy and performance when using high quality unleaded gasoline hav- ing an octane range of 87 to 89. The manu- facturer recommends the use of 89 octane for optimum performance....

  • Page 307

    The manufacturer supports the use of reformulated gaso- lines. Properly blended reformulated gasolines will pro- vide excellent performance and durability of engine and fuel system components. Gasoline/oxygenate blends some fuel suppliers blend unleaded gasoline with oxy- genates such as 10% ethanol...

  • Page 308

    It is even more important to look for gasolines without mmt in canada, because mmt can be used at levels higher than those allowed in the united states. Mmt is prohibited in federal and california reformu- lated gasoline. Materials added to fuel all gasoline sold in the united states is required to ...

  • Page 309

    Carbon monoxide warnings warning! Carbon monoxide (co) in exhaust gases is deadly. Follow the precautions below to prevent carbon monoxide poisoning: • do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas which can kill. Never run the engine in a closed area, such ...

  • Page 310

    Caution! Only vehicles with the e-85 fuel filler door label can operate on e-85. Ethanol fuel (e-85) e-85 is a mixture of approximately 85% fuel ethanol and 15% unleaded gasoline. Warning! Ethanol vapors are extremely flammable and could cause serious personal injury. Never have any smok- ing materi...

  • Page 311

    Note: when the ambient temperature is above 90°f (32°c), you may experience hard starting and rough idle following start up even if the above recommendations are followed. Selection of engine oil for flexible fuel vehicles (e-85) and gasoline vehicles whether operating the vehicle on an e-85 ethanol...

  • Page 312

    Maintenance if you operate the vehicle using e-85 fuel, follow “main- tenance schedule b.” refer to section 8 of this manual. Caution! Do not use ethanol mixture greater than 85% in your vehicle. It will cause difficulty in cold starting and may affect driveability. Fuel requirements — diesel diesel...

  • Page 313

    Adding fuel caution! Do not put gasoline in your diesel vehicle (if equipped). If you accidentally put gasoline in your vehicle, do not start the engine. This will cause damage to the fuel system. Have the fuel system flushed. Fuel filler cap (gas cap) the gas cap is located behind the fuel filler d...

  • Page 314

    Caution! Damage to the fuel system or emission control system could result from using an improper fuel cap (gas cap). A poorly fitting cap could let impurities into the fuel system. Also, a poorly fitting after- market cap can cause the mil (malfunction indica- tor light) to illuminate, due to fuel ...

  • Page 315

    Note: tighten the gas cap about 1/4 turn until you hear one click. This is an indication that cap is properly tightened. If the gas cap is not tighten properly, the malfunction indicator light will come on. Be sure the gas cap is tightened every time the vehicle is refueled. Warning! A fire may resu...

  • Page 316

    Warning! • never add fuel when the engine is running. • never have any smoking materials lit in or near the vehicle when the fuel cap is removed or the tank filled. Vehicle loading certification label as required by national highway traffic safety admin- istration regulations, your vehicle has a cer...

  • Page 317

    Each axle gawr is determined by the components in the system with the lowest load carrying capacity (axle, springs, tires or wheels). Heavier axles or suspension components sometimes specified by purchasers for in- creased durability does not necessarily increase the vehi- cle’s gvwr. Tire size the ...

  • Page 318

    Or rear axles has been exceeded but the total load is within the specified gvwr. If so, weight must be shifted from front to rear or rear to front as appropriate until the specified weight limitations are met. Store the heavier items down low and be sure that the weight is distributed equally. Stow ...

  • Page 319

    Gross trailer weight (gtw) the gross trailer weight (gtw) is the weight of the trailer plus the weight of all cargo, consumables and equipment (permanent or temporary) loaded in or on the trailer in its ⬙loaded and ready for operation⬙ condition. The recom- mended way to measure gtw is to put your f...

  • Page 320

    That typically provides adjustable friction associated with the telescoping motion to dampen any unwanted trailer swaying motions while traveling. Weight-carrying hitch a weight-carrying hitch supports the trailer tongue weight, just as if it were luggage located at a hitch ball or some other connec...

  • Page 321

    Weight distributing hitch system improper adjustment of weight distributing system starting and operating 321 5.

  • Page 322

    Trailer hitch classification your vehicle may be factory equipped for safe towing of trailers weighing over 3,500 lbs (1 587 kg) with the optional trailer tow prep package. See your dealer for package content. The following chart provides the industry standard for the maximum trailer weight a given ...

  • Page 323

    Trailer towing weights (maximum trailer weight ratings) the following chart provides the maximum trailer weight ratings towable for your given drivetrain. Engine/ transmission model gcwr (gross com- bined wt. Rating) frontal area max. Gtw (gross trailer wt.) max. Tongue wt. (see note 1) 3.7l/automat...

  • Page 324

    5.7l/automatic 4x2 12,200 lbs (5 534 kg) 64 sq. Ft. (5.95 square meters) 7,400 lbs (3 357 kg) 740 lbs (336 kg) 5.7l/automatic (overland) 4x2 12,200 lbs (5 534 kg) 64 sq. Ft. (5.95 square meters) 7,395 lbs (3 354 kg) 740 lbs (336 kg) 5.7l/automatic 4x4 12,200 lbs (5 534 kg) 64 sq. Ft. (5.95 square me...

  • Page 325

    Trailer and tongue weight always load a trailer with 60% to 65% of the weight in the front of the trailer. This places 10% to 15% of the gross trailer weight (gtw) on the tow hitch of your vehicle. Loads balanced over the wheels or heavier in the rear can cause the trailer to sway severely side to s...

  • Page 326

    Note: remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options, or dealer-installed options, must be considered as part of the total load on your vehicle. Refer to the tire and loading information plac- ard in the tire safety in...

  • Page 327

    Loss of control, poor performance or damage to brakes, axle, engine, transmission, steering, suspension, chas- sis structure or tires. • safety chains must always be used between your vehicle and trailer. Always connect the chains to the hook retainers of the vehicle hitch. Cross the chains under th...

  • Page 328

    Towing requirements — tires − do not attempt to tow a trailer while using a compact spare tire. − proper tire inflation pressures are essential to the safe and satisfactory operation of your vehicle. Refer to the tires–general information section of this manual on tire pressures for proper tire infl...

  • Page 329

    Caution! If the trailer weighs more than 1,000 lbs (454 kg) loaded, it should have its own brakes and they should be of adequate capacity. Failure to do this could lead to accelerated brake lining wear, higher brake pedal ef- fort, and longer stopping distances. Warning! Do not connect trailer brake...

  • Page 330

    Towing tips before setting out on a trip, practice turning, stopping and backing the trailer in an area away from heavy traffic. 4 - pin connector 7- pin connector 330 starting and operating.

  • Page 331

    Towing tips — automatic transmission the “d” range can be selected when towing. However, if frequent shifting occurs while in this range, the ”tow/ haul” mode (if equipped) or a lower gear range should be selected. Note: using the ”tow/haul” mode (if equipped) or a lower gear range while operating t...

  • Page 332

    − air conditioning turn off temporarily. − refer to cooling system operating information in the maintenance section of this manual for more informa- tion. Recreational towing (behind motorhome, etc.) towing – 2wd models recreational towing is allowed only if the driveshaft is removed. Towing with th...

  • Page 333

    Shifting into neutral (n) use the following procedure to prepare your vehicle for recreational towing. Caution! It is necessary to follow these steps to be certain that the transfer case is fully in n (neutral) before recreational towing to prevent damage to internal parts. 1. Depress brake pedal. 2...

  • Page 334

    5. Start engine. 6. Shift transmission into d (drive). 7. Release brake pedal and ensure that there is no vehicle movement. 8. Shut the engine off. 9. Shift transmission into p (park). 10. Place the ignition key in the off position, and remove key. 11. Apply parking brake. 12. Attach vehicle to the ...

  • Page 335

    Hold down n (neutral) “pin” switch (with a pen, etc.) for 4 seconds until the led lamp by the switch starts to blink indicating shift in progress. Lamp will stop blinking (go out) when shift is complete. The “4wd system in neutral” message will no longer be displayed on the evic (electronic vehicle ...

  • Page 336

    Note: when shifting out of transfer case n (neutral), turning the engine off may be required to avoid gear clash. Warning! You or others could be injured if you leave the vehicle unattended with the transfer case in the n (neutral) position without first fully engaging the parking brake. The transfe...

  • Page 337: Contents

    What to do in emergencies contents 䡵 hazard warning flashers . . . . . . . . . . . . . . . . . 338 䡵 if your engine overheats . . . . . . . . . . . . . . . . . 338 䡵 jacking and tire changing . . . . . . . . . . . . . . . . 339 ▫ jack location . . . . . . . . . . . . . . . . . . . . . . . . 340 ▫ sp...

  • Page 338

    Hazard warning flashers your vehicle’s hazard warning flasher is an emergency warning system. When you activate it, all front and rear directional signals will flash intermittently. Use it when your vehicle is disabled on or near the road. It warns other drivers to steer clear of you and your vehicl...

  • Page 339

    Removes this heat. You can also turn the temperature control to maximum heat, the mode control to floor, and the fan control to high. This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system. Caution! Driving with a hot cooling syste...

  • Page 340

    Jack location the scissor-type jack and tire changing tools are located in the passenger side compartment behind the second row seat. Spare tire stowage the spare tire is stowed under the rear of the vehicle by means of a cable winch mechanism. To remove or stow the spare, use the jack handle to rot...

  • Page 341

    Spare tire removal fit the jack handle extension over the drive nut. Use the lug wrench to rotate the nut counter clockwise until the spare is on the ground with enough slack in the cable to allow to pull the tire out from under the vehicle. Caution! The winch mechanism is designed for use with the ...

  • Page 342

    Preparations for jacking park the vehicle on a firm level surface, avoid ice or slippery areas, set the parking brake and place the gear selector in p (park). Turn off the ignition. Warning! Do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the r...

  • Page 343

    4. Locate the jack as shown. For the front axle, place it under the front lower control arm as shown. For the rear axle, place it under the axle near the wheel to be changed. Ensure the jack is closest to the inside of the wheel when jacking on the rear axle. Do not raise the vehicle until you are s...

  • Page 344

    5. Raise the vehicle by turning the jack screw clockwise. Raise the vehicle only until the tire just clears the surface and enough clearance is obtained to install the spare tire. Minimum tire lift provides maximum stability. Warning! Raising the vehicle higher than necessary can make the vehicle le...

  • Page 345

    Nuts until each nut has been tightened twice. Correct wheel nut tightness is 130 n·m (95 ft. Lbs). If in doubt about the correct tightness, have them checked with a torque wrench by your authorized dealer or at a service station. 10. Lower the jack to it’s fully closed position. Warning! A loose tir...

  • Page 346

    Jump starting if the vehicle has a discharged battery, booster cables may be used to obtain a start from a booster battery or the battery in another vehicle. This type of start can be dangerous if done improperly, so follow this procedure carefully. Warning! Battery fluid is a corrosive acid solutio...

  • Page 347

    2. Park the booster vehicle within cable reach but with- out letting the vehicles touch. Set the parking brake on both vehicles, place the transmission in p (park), and turn the ignition off. 3. Turn off the heater, radio, and all unnecessary electri- cal loads. 4. Connect one end of a jumper cable ...

  • Page 348

    Warning! Do not permit vehicles to touch each other as this could establish a ground connection and personal injury could result. 5. Connect the other cable, first to the negative terminal of the booster battery and then to the engine of the vehicle with the discharged battery. Make sure you have a ...

  • Page 349

    Warning! • you should not try to start your vehicle by push- ing or towing. • do not connect the cable to the negative post of the discharge battery. The resulting electrical spark could cause the battery to explode. • during cold weather when temperatures are be- low freezing point, electrolyte in ...

  • Page 350

    Warning! Stand clear of vehicles when pulling with tow hooks. Tow straps and chains may break, causing serious injury. Towing a disabled vehicle 2wd models only provided the transmission is operable, tow only in n (neutral) at speeds not exceeding 30 mph (48 km/h), for distances of not more than 15 ...

  • Page 351: Maintaining Your Vehicle

    Maintaining your vehicle contents 䡵 engine compartment – 3.7l . . . . . . . . . . . . . . . 354 䡵 engine compartment – 4.7l . . . . . . . . . . . . . . . 355 䡵 engine compartment – 5.7l . . . . . . . . . . . . . . . 356 䡵 engine compartment – 3.0l diesel . . . . . . . . . . 357 䡵 onboard diagnostic ...

  • Page 352

    ▫ maintenance-free battery . . . . . . . . . . . . . . . . 370 ▫ air conditioner maintenance . . . . . . . . . . . . . 371 ▫ power steering fluid check . . . . . . . . . . . . . . 372 ▫ body lubrication . . . . . . . . . . . . . . . . . . . . . 374 ▫ windshield wiper blades . . . . . . . . . . . . ....

  • Page 353

    ▫ front fog light . . . . . . . . . . . . . . . . . . . . . . 404 ▫ rear tail, stop, turn signal, and back-up lights . . . . . . . . . . . . . . . . . . . . . . . 404 ▫ center high mounted stop light (chmsl) . . . 406 䡵 fluids and capacities . . . . . . . . . . . . . . . . . . . 407 䡵 fluids, lubric...

  • Page 354

    Engine compartment – 3.7l 354 maintaining your vehicle.

  • Page 355

    Engine compartment – 4.7l maintaining your vehicle 355 7.

  • Page 356

    Engine compartment – 5.7l 356 maintaining your vehicle.

  • Page 357

    Engine compartment – 3.0l diesel maintaining your vehicle 357 7.

  • Page 358

    Onboard diagnostic system — obd ii your vehicle is equipped with a sophisticated onboard diagnostic system called obd ii. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide ex...

  • Page 359

    Manual). Tighten the gas cap until a ⬙clicking⬙ sound is heard. This is an indication that the gas cap is properly tightened. This message may be temporarily overridden by pressing either the c/t, step, or menu buttons. However, after one minute of no customer interaction, the evic will display agai...

  • Page 360

    Replacement. If the obd system should be determined not ready for the i/m test, your vehicle may fail the test. Your vehicle has a simple ignition key actuated test which you can use prior to going to the test station. To check if your vehicle’s obd system is ready, you must do the following: 1. Ins...

  • Page 361

    During normal vehicle operation, you should have your vehicle serviced before going to the i/m station. The i/m station can fail your vehicle because the mil symbol is on with the engine running. Replacement parts use of genuine mopar 威 parts for normal/scheduled maintenance and repairs is highly re...

  • Page 362

    Maintenance procedures the pages that follow contain the required maintenance services determined by the engineers who designed your vehicle. Besides the maintenance items for which there are fixed maintenance intervals, there are other items that should operate satisfactorily without periodic maint...

  • Page 363

    Change engine oil road conditions as well as your kind of driving affect the interval at which your oil should be changed. Check the following to determine if any apply to you: • day or night temperatures are below 32°f (0°c) • stop and go driving • extensive engine idling • driving in dusty conditi...

  • Page 364

    Material standard ms-6395. Use mopar 威 or an equiva- lent oil meeting the specification ms-6395. Engine oil selection - diesel engines for best performance and maximum protection for all engines under all types of operating conditions, the manufacturer recommends engine oils that are api cer- tified...

  • Page 365

    For information on engine oil filler cap location, see the engine compartment illustration in this section. Lubricants which do not have both, the engine oil certi- fication mark and the correct sae viscosity grade num- ber should not be used. Engine oil viscosity (3.0l diesel engine) caution! Your ...

  • Page 366

    Indiscriminately discarded, can present a problem to the environment. Contact your local authorized dealer, ser- vice station, or governmental agency for advice on how and where used oil and oil filters can be safely discarded in your area. Engine oil filter the engine oil filter should be replaced ...

  • Page 367

    Spark plugs spark plugs must fire properly to assure engine perfor- mance and emission control. New spark plugs should be installed at the specified mileage. The entire set should be replaced if there is any malfunction due to a faulty spark plug. Refer to the “vehicle emission control informa- tion...

  • Page 368

    Catalytic converter the catalytic converter requires the use of unleaded fuel only. Leaded gasoline will destroy the effectiveness of the converter as an emission control device. Under normal operating conditions, the catalytic con- verter will not require maintenance. However, it is im- portant to ...

  • Page 369

    Warning! A hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your ex- haust system. Do not park or operate your vehicle in areas where your exhaust system can contact any- thing that can burn. In unusual sit...

  • Page 370

    Check ventilation hose for indication of damage or plugging deposits. Replace if necessary. Maintenance-free battery your vehicle is equipped with a maintenance-free battery. You will never have to add water, nor is periodic main- tenance required. Warning! • battery fluid is a corrosive acid soluti...

  • Page 371

    To determine the battery charge, check the battery test indicator (if equipped) on top of the battery. Refer to the illustration. Caution! • it is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the neg...

  • Page 372

    Cleaning of the condenser fins and a performance test. Drive belt condition should also be checked at this time. Warning! • use only refrigerants and compressor lubricants approved by the manufacturer for your air condi- tioning system. Some unapproved refrigerants are flammable and can explode, inj...

  • Page 373

    Caution! Do not use automatic transmission fluid (atf) or other types of power steering fluids when servicing the power steering system of this vehicle. Damage to the power steering system can result from the use of the wrong power steering fluid. Checking the power steering fluid level at a defined...

  • Page 374

    Body lubrication locks and all body pivot points, including such items as seat tracks, doors, tailgate and hood hinges, should be lubricated periodically to assure quiet, easy operation and to protect against rust and wear. Prior to the appli- cation of any lubricant, the parts concerned should be w...

  • Page 375

    The fluid reservoir for the windshield washers and the rear window washer is shared. It is located in the front of the engine compartment (on the driver side), and should be checked for fluid level at regular intervals. Fill the reservoir with windshield washer solvent (not antifreeze/coolant) and o...

  • Page 376

    Warning! Exhaust gases can injure or kill. They contain carbon monoxide (co) which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing co, refer to exhaust gas in the safety tips section of this manual. Cooling system warning! You or oth...

  • Page 377

    For any accumulation of bugs, leaves, etc. If dirty, clean by gently spraying water from a garden hose vertically down the face of the condenser. Check the engine cooling system hoses for brittle rubber, cracking, tears, cuts, and tightness of the connection at the coolant recovery bottle and radiat...

  • Page 378

    Caution! Mixing of antifreeze/coolant other than the specified hoat antifreeze/coolant may result in decreased corrosion protection and engine damage. If a non- hoat antifreeze/coolant is introduced into the cool- ing system in an emergency, it should be replaced with the specified antifreeze/coolan...

  • Page 379

    Use only high purity water such as distilled or deionized water when mixing the water/antifreeze (coolant) solu- tion. The use of lower quality water will reduce the amount of corrosion protection in the engine cooling system. Please note that it is the owner’s responsibility to main- tain the prope...

  • Page 380

    Disposal of used engine coolant used ethylene glycol-based antifreeze/coolant is a regu- lated substance requiring proper disposal. Check with your local authorities to determine the disposal rules for your community. To prevent ingestion by animals and children, do not store ethylene glycol-based a...

  • Page 381

    If an examination of your engine compartment shows no evidence of radiator or hose leaks, the vehicle may be safely driven. The vapor will soon dissipate. • do not overfill the coolant recovery bottle. • check antifreeze/coolant freeze point in the radiator and in the coolant recovery bottle. If ant...

  • Page 382

    Pay particular attention to the hoses nearest to high heat sources such as the exhaust manifold. Inspect hose rout- ing to be sure hoses do not touch any heat source or moving component that may cause heat damage or mechanical wear. Insure nylon tubing in these areas has not melted or collapsed. Ins...

  • Page 383

    Brake and power steering system hoses when servicing the vehicle for scheduled maintenance, inspect surface of hoses for evidence of heat and me- chanical damage. Hard and brittle rubber, cracking, tears, cuts, abrasion, and excessive swelling suggest deteriora- tion of the rubber. Particular attent...

  • Page 384

    Brake master cylinder — brake fluid level check the fluid level of the master cylinder should be checked when performing under the hood service, or immedi- ately if the brake system warning lamp indicates system failure. The brake master cylinder has a translucent plastic reservoir. On the outboard ...

  • Page 385

    Caution! Do not allow a petroleum-base fluid to contaminate the brake fluid. Seal damage may result. Front/rear axle fluid front axle fluid level check lubricant should be to the bottom of the oil fill hole. Rear axle fluid level check lubricant should be 1/2” (1 cm) below the oil fill hole. Adding ...

  • Page 386

    Caution! When installing plugs, do not overtighten. You could damage them and cause them to leak. Selection of lubricant use only manufacturer’s recommended fluid, refer to fluids, lubricants, and genuine parts for correct fluid type. Automatic transmission selection of lubricant it is important tha...

  • Page 387

    Check the fluid level while the transmission is at normal operating temperature. This occurs after at least 15 miles (25 km) of driving. At normal operating temperature the fluid cannot be held comfortably between the fingertips. To check the automatic transmission fluid level properly, the followin...

  • Page 388

    Caution! Be aware that if the fluid temperature is below 50°f (10°c) it may not register on the dipstick. Do not add fluid until the temperature is elevated enough to produce an accurate reading. 7. Check for leaks. Release parking brake. To prevent dirt and water from entering the transmission afte...

  • Page 389

    Service manual. Also check for accumulations of vegeta- tion or brush that could become a fire hazard, or conceal damage to fuel lines, brake hoses, axle pinion seals, and propeller shafts. Caution! Under frequent heavy-duty driving conditions, change all lubricants and lubricate body compo- nents, ...

  • Page 390

    Washing • wash your vehicle regularly. Always wash your ve- hicle in the shade using mopar 威 car wash or a mild car wash soap, and rinse the panels completely with clear water. • if insects, tar, or other similar deposits have accumu- lated on your vehicle, use mopar 威 super kleen bug and tar remove...

  • Page 391

    • if your vehicle is damaged due to an accident or similar cause which destroys the paint and protective coating have your vehicle repaired as soon as possible. The cost of such repairs is considered the responsibil- ity of the owner. • if you carry special cargo such as chemicals, fertilizers, de-i...

  • Page 392

    Your leather upholstery can be best preserved by regular cleaning with a damp soft cloth. Small particles of dirt can act as an abrasive and damage the leather upholstery and should be removed promptly with a damp cloth. Stubborn soils can be removed easily with a soft cloth and mopar 威 total clean....

  • Page 393

    Equipped with electric defrosters. Do not use scrapers or other sharp instruments which may scratch the elements. When cleaning the rear view mirror, spray cleaner on the towel or rag that you are using. Do not spray cleaner directly on the mirror. Cleaning plastic instrument cluster lenses the lens...

  • Page 394

    Cavity cartridge fuse mini fuse description 1 30 amp green audio amp (b+) 2 15 amp blue sunroof (b+) cavity cartridge fuse mini fuse description 3 10 amp red htd mirror (ebl) 4 20 amp yellow rr pwr out (b+) 5 10 amp red rr hvac (r/o) (xk only) 6 spare (b+) 7 20 amp yellow door locks (b+) 8 15 amp bl...

  • Page 395

    Cavity cartridge fuse mini fuse description 10 10 amp red final drive control module (fdcm), heater ventilation, air conditioning (hvac), switch bank, transfer case switch, o/h, heater ventila- tion, air conditioning (hvac) relay, rear park assist 11 spare (b+) 12 10 amp red door mods, mem. Sw, o/h ...

  • Page 396

    Cavity cartridge fuse mini fuse description 21 spare (acc de- lay) 22 15 amp blue rear wiper (b+) 24 10 amp red power distribution center (pdc) relays, final drive control module (fdcm), front control module (fcm) (r/s), a580 (r/s) 25 10 amp red shifter assy (btsi), trans. Case switch, esp/abs, brak...

  • Page 397

    Cavity cartridge fuse mini fuse description 2 30 amp pink power outlets 3 30 amp pink rr wiper/ign r/o 4 30 amp pink abs pump 5 50 amp red cabin htr 1 (diesel only) 6 50 amp red auto shut down (asd) 7 30 amp pink rr hvac (xk only) 8 40 amp green acc delay/seats 9 40 amp green pwr liftgate (xk only) ...

  • Page 398

    Cavity cartridge fuse mini fuse description 18 20 amp yellow eatx/ac clutch 19 20 amp yellow ign sw 20 20 amp yellow pcm batt (gasoline only) 21 30 amp green abs valves 22 20 amp yellow t-tow (bux) 23 20 amp yellow final drive control module (fdcm) 24 20 amp yellow fuel pump 25 20 amp yellow final d...

  • Page 399

    Underhood fuses (integrated power module) cavity cartridge fuse mini fuse description 8 10 amp red lt park lamps cavity cartridge fuse mini fuse description 9 10 amp red trailer-tow park lamps 10 10 amp red rt park lamps 12 20 amp yellow front control module (fcm) batt #4 13 20 amp yellow front cont...

  • Page 400

    Cavity cartridge fuse mini fuse description 18 20 amp yellow front control module (fcm) batt #1 19 20 amp yellow lt trailer-tow stop/ turn 20 20 amp yellow front control module (fcm) batt #3 21 20 amp yellow rt trailer-tow stop/ turn 22 30 amp pink final drive control module (fdcm) mod 23 50 amp red...

  • Page 401

    In the fresh air and high blower setting. This will insure adequate system lubrication to minimize the possibility of compressor damage when the system is started again. Replacement bulbs interior lights bulb type glove box light . . . . . . . . . . . . . . . . . . . . . . . . . 194 grab handle ligh...

  • Page 402

    2bulb replacement head light 1. Open the hood. 2. Remove the headlamp cover. 3. Turn the low or high beam bulb 1/4 turn counter clockwise to remove from housing. 4. Disconnect the electrical connector and replace the bulb. Caution! Do not touch the new bulb with your fingers. Oil contamination will ...

  • Page 403

    Front turn signal 1. Open the hood. 2. Remove the headlamp cover. 3. Turn the turn signal bulb 1/4 turn counter clockwise to remove from housing. 4. Disconnect the electrical connector and replace the bulb. Maintaining your vehicle 403 7.

  • Page 404

    Caution! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol. Front fog light 1. Reach behind the front fascia from under the vehicle. 2. Turn the front fog light bulb ...

  • Page 405

    3. Squeeze the socket assembly tabs to remove it from the housing. 4. Pull the bulb to remove it from the socket. 5. Replace the bulb, reinstall the socket, and reattach the light assembly. Maintaining your vehicle 405 7.

  • Page 406

    Center high mounted stop light (chmsl) 1. Remove the two screws securing the chmsl. 2. Twist the bulb socket to remove from the chmsl housing. 3. Pull the bulb out of the socket. 4. Replace the bulb, reinstall the socket and reattach the chmsl. 406 maintaining your vehicle.

  • Page 407

    Fluids and capacities u.S. Metric fuel (approximate) 3.7/4.7/5.7l gasoline engines 21 gallons 79 liters 3.0l diesel engine 22 gallons 83 liters engine oil with filter 3.7 liter engine (sae 5w-20, api certified) 5 qts 4.7 liters 4.7 liter engine (sae 5w-20, api certified) 6 qts 5.7 liters 5.7 liter e...

  • Page 408

    Fluids, lubricants, and genuine parts engine component fluid, lubricant, or genuine part engine coolant mopar 威 antifreeze/coolant 5 year/100,000 mile formula hoat (hybrid organic additive technology) engine oil (3.7l/4.7l/5.7l engines) use api certified sae 5w-20 engine oil, meeting the requirement...

  • Page 409

    Chassis component fluid, lubricant, or genuine part automatic transmission mopar 威 atf+4 automatic transmission fluid transfer case (3.7l engine only) mopar 威 atf+4 automatic transmission fluid transfer case mopar 威 nv 247/245 transfer case lubricant axle differential (front-rear) mopar 威 synthetic ...

  • Page 411: Maintenance Schedules

    Maintenance schedules contents 䡵 emission control system maintenance . . . . . . . . 412 䡵 maintenance schedules . . . . . . . . . . . . . . . . . . . 412 ▫ schedule “b” . . . . . . . . . . . . . . . . . . . . . . . . 415 ▫ schedule “a” . . . . . . . . . . . . . . . . . . . . . . . . 427 䡵 maintenan...

  • Page 412

    Emission control system maintenance the “scheduled” maintenance services, listed in bold type must be done at the times or mileages specified to assure the continued proper functioning of the emission control system. These, and all other maintenance services included in this manual, should be done t...

  • Page 413

    • taxi, police, or delivery service (commercial service) • off-road or desert driving note: most vehicles are operated under the conditions listed for schedule “b.” note: if any of these apply to you, change your engine oil every 3,000 miles (5 000 km) or 3 months, whichever comes first, and follow ...

  • Page 414

    Once a month • check the tire pressure and look for unusual wear or damage. • inspect the battery and clean and tighten the terminals as required. • check the fluid levels of the coolant reservoir, brake master cylinder, and transmission, and add as needed. • check all lights and all other electrica...

  • Page 415

    Schedule “b” follow this schedule if you usually operate your vehicle under one or more of the following conditions. • day or night temperatures are below 32°f (0°c) • stop and go driving • excessive engine idling • driving in dusty conditions • short trips of less than 10 miles (16.2 km) • more tha...

  • Page 416

    Miles 3,000 6,000 9,000 12,000 15,000 (kilometers) (5 000) (10 000) (15 000) (20 000) (25 000) change the engine oil and engine oil filter, if not replaced at 3 months. X x x x x rotate the tires. X x check spare tire for proper pressure and correct stowage. X x inspect the engine air cleaner filter...

  • Page 417

    Miles 18,000 21,000 24,000 27,000 30,000 (kilometers) (30 000) (35 000) (40 000) (45 000) (50 000) change the engine oil and engine oil filter, if not replaced at 3 months. X x x x x rotate the tires. X x x check spare tire for proper pressure and correct stowage. X x x inspect the engine air cleane...

  • Page 418

    Miles 33,000 36,000 39,000 42,000 45,000 (kilometers) (55 000) (60 000) (65 000) (70 000) (75 000) change the engine oil and engine oil filter, if not replaced at 3 months. X x x x x rotate the tires. X x check spare tire for proper pressure and correct stowage. X x inspect the engine air cleaner fi...

  • Page 419

    Miles 48,000 51,000 54,000 57,000 60,000 (kilometers) (80 000) (85 000) (90 000) (95 000) (100 000) change the engine oil and engine oil filter, if not replaced at 3 months. X x x x x rotate the tires. X x x check spare tire for proper pressure and correct stowage. X x x inspect the engine air clean...

  • Page 420

    Miles 63,000 66,000 69,000 72,000 75,000 (kilometers) (105 000) (110 000) (115 000) (120 000) (125 000) change the engine oil and engine oil filter, if not replaced at 3 months. X x x x x rotate the tires. X x check spare tire for proper pressure and correct stowage. X x inspect the engine air clean...

  • Page 421

    Miles 78,000 81,000 84,000 87,000 90,000 (kilometers) (130 000) (135 000) (140 000) (145 000) (150 000) change the engine oil and engine oil filter, if not replaced at 3 months. X x x x x rotate the tires. X x x check spare tire for proper pressure and correct stowage. X x x inspect the engine air c...

  • Page 422

    Miles 93,000 96,000 99,000 102,000 105,000 (kilometers) (155 000) (160 000) (165 000) (170 000) (175 000) change the engine oil and engine oil filter, if not replaced at 3 months. X x x x x rotate the tires. X x check spare tire for proper pressure and correct stowage. X x inspect the engine air cle...

  • Page 423

    Miles 108,000 111,000 114,000 117,000 120,000 (kilometers) (180 000) (185 000) (190 000) (195 000) (200 000) change the engine oil and engine oil filter, if not replaced at 3 months. X x x x x rotate the tires. X x x check spare tire for proper pressure and correct stowage. X x x inspect the engine ...

  • Page 424

    Miles 123,000 126,000 129,000 132,000 135,000 (kilometers) (205 000) (210 000) (215 000) (220 000) (225 000) change the engine oil and engine oil filter, if not replaced at 3 months. X x x x x rotate the tires. X x x check spare tire for proper pressure and correct stowage. X x x inspect the engine ...

  • Page 425

    Miles 138,000 141,000 144,000 147,000 150,000 (kilometers) (230 000) (235 000) (240 000) (245 000) (250 000) change the engine oil and engine oil filter, if not replaced at 3 months. X x x x x rotate the tires. X x x check spare tire for proper pressure and correct stowage. X x x inspect the engine ...

  • Page 426

    Inspection and service should also be performed anytime a malfunction is observed or suspected. Retain all re- ceipts. 〫 this maintenance is recommended by the manufac- turer to the owner, but is not required to maintain emissions warranty. * this maintenance is not required if the belt was previous...

  • Page 427

    Schedule “a” miles 6,000 12,000 18,000 24,000 30,000 (kilometers) (10 000) (20 000) (30 000) (40 000) (50 000) [months] [6] [12] [18] [24] [30] change the engine oil and engine oil filter. X x x x x rotate the tires. X x x x x check spare tire for proper pressure and correct stowage. X x x x x inspe...

  • Page 428

    Miles 36,000 42,000 48,000 54, 000 (kilometers) (60 000) (70 000) (80 000) (90 000) [months] [36] [42] [48] [54] change the engine oil and engine oil filter. X x x x rotate the tires. X x x x check spare tire for proper pressure and correct stowage. X x x x inspect the brake linings. X x 428 schedul...

  • Page 429

    Miles 60,000 66,000 72,000 78,000 (kilometers) (100 000) (110 000) (120 000) (130 000) [months] [60] [66] [72] [78] change the engine oil and engine oil filter. X x x x rotate the tires. X x x x check spare tire for proper pressure and correct stowage. X x x x inspect the engine air cleaner filter, ...

  • Page 430

    Miles 84,000 90,000 96,000 102, 000 (kilometers) (140 000) (150 000) (160 000) (170 000) [months] [84] [90] [96] [102] change the engine oil and engine oil filter. X x x x rotate the tires. X x x x check spare tire for proper pressure and correct stowage. X x x x inspect the engine air cleaner filte...

  • Page 431

    Miles 108,000 114,000 120,000 126,000 (kilometers) (180 000) (190 000) (200 000) (210 000) [months] [108] [114] [120] [126] change the engine oil and engine oil filter. X x x x rotate the tires. X x x x check spare tire for proper pressure and correct stowage. X x x x inspect the engine air cleaner ...

  • Page 432

    Miles 132,000 138,000 144,000 150,000 (kilometers) (220 000) (230 000) (240 000) (250 000) [months] [132] [138] [144] [150] change the engine oil and engine oil filter. X x x x rotate the tires. X x x x check spare tire for proper pressure and correct stowage. X x x x inspect the engine air cleaner ...

  • Page 433

    Inspection and service should also be performed anytime a malfunction is observed or suspected. Retain all re- ceipts. 〫 this maintenance is recommended by the manufac- turer to the owner, but is not required to maintain emissions warranty. * this maintenance is not required if the belt was previous...

  • Page 434

    Note: most vehicles are operated under the conditions listed for schedule “b.” second is schedule “a”. It is for vehicles that are not operated under any of the conditions listed under sched- ule “b.” use the schedule that best describes your driving condi- tions. Where time and mileage are listed, ...

  • Page 435

    At each oil change • change the engine oil filter. • inspect the exhaust system. • inspect brake hoses. • check the engine coolant/anti-freeze level, hoses, and clamps. • inspect engine accessory drive belts. Replace as neces- sary. • inspect for the presence of water in the fuel filter/ water separ...

  • Page 436

    Schedule “b” — diesel engines follow schedule “b” if you usually operate your vehicle under one or more of the following conditions. • day or night temperatures are below 32°f (0°c). • stop and go driving. • extensive engine idling. • driving in dusty conditions. • short trips of less than 10 miles ...

  • Page 437

    Miles 6,250 12,500 18,750 25,000 31,250 (kilometers) (10 000) (20 000) (30 000) (40 000) (50 000) change the engine oil and engine oil filter. X x x x x rotate the tires. X x x check spare tire for proper pressure and correct stowage. X x x x x inspect the engine air filter element. Replace as neces...

  • Page 438

    Miles 37,500 43,750 50,000 56,250 62,500 (kilometers) (60 000) (70 000) (80 000) (90 000) (100 000) change the engine oil and engine oil filter. X x x x x rotate the tires. X x check spare tire for proper pressure and correct stowage. X x x x x inspect the engine air filter element. Replace as neces...

  • Page 439

    Miles 68,750 75,000 81,250 87,500 93,750 100,000 (kilometers) (110 000) (120 000) (130 000) (140 000) (150 000) (160 000) change the engine oil and engine oil filter. X x x x x x rotate the tires. X x x check spare tire for proper pressure and cor- rect stowage. X x x x x x inspect the engine air fi...

  • Page 440

    〫 applies only if vehicle is used for frequent trailer towing, or fleet/commercial service. † the replacement of such component is requested when there is superficial wear, bearing clearance, or evident grease leak. Inspection and service should be performed anytime a malfunction is observed or susp...

  • Page 441

    Schedule “a” miles 12,500 25,000 37,500 50,000 (kilometers) (20 000) (40 000) (60 000) (80 000) change the engine oil and engine oil filter. X x x x rotate the tires. X x x x check spare tire for proper pressure and correct stowage. X x x x inspect the engine air filter element. Replace as neces- sa...

  • Page 442

    Miles 62,500 75,000 87,500 100,000 (kilometers) (100 000) (120 000) (140 000) (160 000) change the engine oil and engine oil filter. X x x x rotate the tires. X x x x check spare tire for proper pressure and correct stowage. X x x x inspect the engine air filter element. Replace as neces- sary. X x ...

  • Page 443: Contents

    If you need consumer assistance contents 䡵 suggestions for obtaining service for your vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . 444 ▫ prepare for the appointment . . . . . . . . . . . . 444 ▫ prepare a list . . . . . . . . . . . . . . . . . . . . . . . . 444 ▫ be reasonable with re...

  • Page 444

    Suggestions for obtaining service for your vehicle prepare for the appointment if you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty, discuss additional charges with the service manager. ...

  • Page 445

    Technicians, special tools, and the latest information to assure your vehicle is fixed correctly and in a timely manner. This is why you should always talk to your dealer’s service manager first. Most matters can be resolved with this process. • if for some reason you are still not satisfied, talk t...

  • Page 446

    Customer assistance for the hearing or speech impaired (tdd/tty) to assist customers who have hearing difficulties, the manufacturer has installed special tdd (telecommuni- cation devices for the deaf) equipment at its customer center. Any hearing or speech impaired customer who has access to a tdd ...

  • Page 447

    Warranty information (u.S. Vehicles only) see the warranty information booklet for the terms and provisions of daimlerchrysler’s warranties applicable to this vehicle. Mopar 姞 parts mopar 威 fluids, lubricants, parts, and accessories are available from your dealer. They will help you keep your vehicl...

  • Page 448

    Publication order forms to order the following manuals, you may use either the website or the phone numbers listed below. Visa, mas- tercard, american express, and discover orders are ac- cepted. If you prefer mailing your payment, please call for an order form. Note: a street address is required wh...

  • Page 449

    Call toll free at: • 1–800–890–4038 (u.S.) • 1–800–387–1143 (canada) or visit us on the world wide web at: • www.Techauthority.Daimlerchrysler.Com • www.Daimlerchrysler.Ca/manuals department of transportation uniform tire quality grades the following describes the tire grading categories estab- lish...

  • Page 450

    On specified government test surfaces of asphalt and concrete. A tire marked c may have poor traction perfor- mance. Warning! The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction chara...

  • Page 451: Index

    Index 10

  • Page 452

    Abs (anti-lock brake system) . . . . . . . . . . . . 176,274 adding fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . 313 adding washer fluid . . . . . . . . . . . . . . . . . . . . . 165 adjustable pedals . . . . . . . . . . . . . . . . . . . . . . . 124 air cleaner, engine (engine air cle...

  • Page 453

    Autostick . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 256 auxiliary electrical outlet (power outlet) . . . . . . 156 auxiliary power outlet . . . . . . . . . . . . . . . . . . . 156 battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 370 emergency starting . . . . . ....

  • Page 454

    Cargo light . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159 cargo load floor . . . . . . . . . . . . . . . . . . . . . . . . 163 cargo tie-downs . . . . . . . . . . . . . . . . . . . . . . . . 161 catalytic converter . . . . . . . . . . . . . . . . . . . . . . 368 caution, exhaust gas . ...

  • Page 455

    Cruise light . . . . . . . . . . . . . . . . . . . . . . . . . . . 181 cup holder . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158 customer assistance . . . . . . . . . . . . . . . . . . . . . 444 data recorder, event . . . . . . . . . . . . . . . . . . . . . . 52 daytime running lights ....

  • Page 456

    Electronic vehicle information center (evic) . . . . . . . . . . . . . . . . . . . . . . . 180,183 emergency, in case of freeing vehicle when stuck . . . . . . . . . . . . . . . 261 hazard warning flasher . . . . . . . . . . . . . . . . . 338 jacking . . . . . . . . . . . . . . . . . . . . . . . . ....

  • Page 457

    Filters air cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . 367 engine oil . . . . . . . . . . . . . . . . . . . . . . . . . . . 366 engine oil disposal . . . . . . . . . . . . . . . . . . . . 365 finish care . . . . . . . . . . . . . . . . . . . . . . . . . . . . 390 flashers . . . . . ...

  • Page 458

    Gauge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181 hoses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 382 materials added . . . . . . . . . . . . . . . . . . . . . . . 308 octane rating . . . . . . . . . . . . . . . . . . . . . . 305,306 requirements . . . . . . . ....

  • Page 459

    Heated mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . 76 heated seats . . . . . . . . . . . . . . . . . . . . . . . . . . . 102 heater, engine block . . . . . . . . . . . . . . . . . . . . . 253 high beam indicator . . . . . . . . . . . . . . . . . . . . . 175 high beam/low beam select ...

  • Page 460

    Key, replacement . . . . . . . . . . . . . . . . . . . . . . . . 17 key, sentry (immobilizer) . . . . . . . . . . . . . . . . . . . 15 key-in reminder . . . . . . . . . . . . . . . . . . . . . . . . . 15 keyless entry system . . . . . . . . . . . . . . . . . . . . . . 19 keys . . . . . . . . . . . ....

  • Page 461

    Headlight switch . . . . . . . . . . . . . . . . . . . . . . 114 headlights . . . . . . . . . . . . . . . . . . . . . . . . . . . 402 headlights on with wipers . . . . . . . . . . . . . . . 114 high beam indicator . . . . . . . . . . . . . . . . . . . . 175 illuminated entry . . . . . . . . . . . . ...

  • Page 462

    Lower anchors and tether for children (latch) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58,60 lubrication, body . . . . . . . . . . . . . . . . . . . . . . . 374 luggage rack (roof rack) . . . . . . . . . . . . . . . . . 166 lumbar support . . . . . . . . . . . . . . . . . . . . . . . ...

  • Page 463

    New vehicle break-in period . . . . . . . . . . . . . . . . 64 occupant restraints . . . . . . . . . . . . . . . . . . . . . . . 34 octane rating, gasoline (fuel) . . . . . . . . . . . . 305,306 odometer . . . . . . . . . . . . . . . . . . . . . . . . . . 180,181 trip . . . . . . . . . . . . . . . ....

  • Page 464

    Pets, transporting . . . . . . . . . . . . . . . . . . . . . . . . 64 phone, cellular . . . . . . . . . . . . . . . . . . . . . . . . . . 77 phone, hands-free (uconnect™) . . . . . . . . . . . . . 77 placard, tire and loading information . . . . . . . . . 283 polishing and waxing . . . . . . . . . ....

  • Page 465

    Rear wiper/washer . . . . . . . . . . . . . . . . . . . . . . 164 rearview mirrors . . . . . . . . . . . . . . . . . . . . . . . . 72 reclining front seats . . . . . . . . . . . . . . . . . . . . . 100 recorder, event data . . . . . . . . . . . . . . . . . . . . . . 52 recreational towing . . . . . ...

  • Page 466

    Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 maintenance . . . . . . . . . . . . . . . . . . . . . . . . 65,393 pretensioners . . . . . . . . . . . . . . . . . . . . . . . . . . 41 reminder . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181 shoulder belt anchorage ....

  • Page 467

    Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 363,364 speed control (cruise control) . . . . . . . . . . . . . . 126 speedometer . . . . . . . . . . . . . . . . . . . . . . . . . . . 175 starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 249 automatic transmissi...

  • Page 468

    Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66,287,449 air pressure . . . . . . . . . . . . . . . . . . . . . . . . . . 288 alignment and balance . . . . . . . . . . . . . . . . . . 293 chains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 294 changing . . . . . . . . ...

  • Page 469

    Trailer and tongue weight . . . . . . . . . . . . . . . . 325 wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 329 trailer towing guide . . . . . . . . . . . . . . . . . . . . . 323 trailer weight . . . . . . . . . . . . . . . . . . . . . . . . . . 323 transfer case . . . . . . . ....

  • Page 470

    Washers, windshield . . . . . . . . . . . . . . . . . . 120,374 washing vehicle . . . . . . . . . . . . . . . . . . . . . . . . . 390 waxing and polishing . . . . . . . . . . . . . . . . . . . . . 390 wheel alignment and balance . . . . . . . . . . . . . . . 293 wheel and wheel trim . . . . . . . . ...

  • Page 471: Notes

    Notes.

  • Page 472: Notes

    Notes.