1. DL manuals
  2. Jeep
  3. Automobile
  4. 2007 JK Wrangler
  5. Owner's Manual

Jeep 2007 JK Wrangler Owner's Manual

Summary of 2007 JK Wrangler

  • Page 1

    Table of contents section page 1 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 things to know before starting your vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 3 understanding the fea...

  • Page 3: Introduction

    Introduction contents 䡵 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 ▫ roll over warning . . . . . . . . . . . . . . . . . . . . . 5 䡵 how to use this manual . . . . . . . . . . . . . . . . . . 7 䡵 warnings and cautions . . . . . . . . . . . . . . . . . . . 9 䡵 vehicle identi...

  • Page 4

    Introduction this is a specialized utility vehicle designed for both on-road and off-road use. It can go places and perform tasks for which conventional two-wheel drive enclosed vehicles were not intended. It handles and maneuvers differently from many passenger cars both on-road and off-road, so ta...

  • Page 5

    Roll over warning utility vehicles have a significantly higher roll over rate than other types of vehicles. This vehicle has a higher ground clearance, higher center of gravity, and narrower track than many passenger cars. It is capable of perform- ing better in a wide variety of off-road applicatio...

  • Page 6

    Million annually. In a roll over crash, an unbelted person is significantly more likely to die than a person wearing a seal belt. Always buckle up. Although your vehicle may be equipped with a soft top or optional hard top to give the occupants protection from the weather, these tops do not offer st...

  • Page 7

    When it comes to service, remember that your authorized dealer knows your vehicle best, has the factory-trained technicians and genuine mopar 威 parts, and is interested in your satisfaction. Warning! Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals k...

  • Page 8

    8 introduction.

  • Page 9

    Warnings and cautions this manual contains warnings against operating procedures which could result in an accident or bodily injury. It also contains cautions against procedures which could result in damage to your vehicle. If you do not read this entire manual you may miss important information. Ob...

  • Page 11: Contents

    Things to know before starting your vehicle contents 䡵 a word about your keys . . . . . . . . . . . . . . . . . .14 ▫ ignition key removal . . . . . . . . . . . . . . . . . . .14 ▫ key-in-ignition reminder . . . . . . . . . . . . . . . .15 䡵 steering wheel lock — if equipped . . . . . . . . . .15 ▫ ...

  • Page 12

    ▫ using the panic alarm . . . . . . . . . . . . . . . . . .22 ▫ to turn off “flash lights with lock” . . . . . . . .22 ▫ programming additional transmitters . . . . . . . .23 ▫ general information . . . . . . . . . . . . . . . . . . . .24 ▫ battery replacement . . . . . . . . . . . . . . . . . . . ....

  • Page 13

    ▫ child restraint . . . . . . . . . . . . . . . . . . . . . . . .63 䡵 engine break-in recommendations . . . . . . . . . . .75 䡵 safety tips . . . . . . . . . . . . . . . . . . . . . . . . . . . .76 ▫ exhaust gas . . . . . . . . . . . . . . . . . . . . . . . . . .76 ▫ safety checks you should make in...

  • Page 14

    A word about your keys the keys for your new vehicle are enclosed in a plastic bag with the key code number on it. If you received your keys without the bag, ask your dealer to give you the number. The key code can also be obtained by the dealer from your vehicle invoice. Ignition key removal manual...

  • Page 15

    Warning! Leaving children in a vehicle unattended is danger- ous for a number of reasons. A child or others could be injured. Children should be warned not to touch the parking brake, brake pedal, or the gear selector lever. Do not leave the keys in the ignition. A child could operate power windows,...

  • Page 16

    To release the steering wheel lock insert the key in the ignition and turn the wheel slightly to the right or left to disengage the lock. Note: if you turned the wheel to the right to engage the lock, you must turn the wheel slightly to the right to disengage it. If you turned the wheel to the left ...

  • Page 17

    Longer than 10 seconds) a fault has been detected in the electronics and the vehicle should be serviced as soon as possible. Note: • the sentry key immobilizer system is not compatible with remote starting systems. Use of these systems may result in vehicle starting problems and loss of security pro...

  • Page 18

    Consists of programming a blank key to the vehicle electronics. A blank key is one which has never been programmed. Note: when having the sentry key system serviced, bring all vehicle keys to the dealer. Customer key programming you can program new keys to the system if you have two valid keys by do...

  • Page 19

    2. This device must accept any interference that may be received, including interference that may cause undes- ired operation. Security alarm system — if equipped this system monitors the vehicle doors, swing gate, and ignition for unauthorized operation. When the alarm is activated, the system prov...

  • Page 20

    The security alarm system is designed to protect your vehicle; however, you can create conditions where the system will arm unexpectedly. If you remain in the vehicle and lock the doors with the transmitter, once the system is armed (after 16 seconds), when you pull the door handle to exit the alarm...

  • Page 21

    Note: the line of transmission must not be blocked with metal objects. To unlock the doors and swing gate press and release the “unlock” button on the key fob once to unlock only the driver’s door or twice to unlock all the doors and swing gate. When the “unlock” button is pressed, the illuminated e...

  • Page 22

    2. While the “lock” button is pressed (after 4 seconds), press the panic button. Release both buttons. The “sound horn on lock” feature can be reactivated by repeating this procedure. Using the panic alarm to turn the panic alarm feature on or off, press and hold the panic button on the transmitter ...

  • Page 23

    The “flash lights on lock/unlock” feature can be reactivated by repeating this procedure. Programming additional transmitters vehicles will be shipped from the assembly plants with two key fob transmitters programmed only for that vehicle. A total of eight fobs can be programmed for your vehicle. Ad...

  • Page 24

    11. A single chime will be heard. 12. Repeat steps 8 through 10 to program up to six additional fobs. 13. Turn the ignition to the off position. 14. Your vehicle will remain in program mode up to 60 seconds from when the original chime was heard. After 60 seconds, all programmed fobs function normal...

  • Page 25

    Battery replacement the recommended replacement battery is cr2032. 1. If the key fob is equipped with a screw, remove the screw. With the transmitter buttons facing down, use a flat blade (screw driver) to pry the two halves of the transmitter apart. Use extreme care not to damage the seal or intern...

  • Page 26

    Shown in the vf display and will also continue to cycle. If the vehicle is moving, three single chimes will occur (one chime for each complete display cycle (three cycles total). After this, the display will continue to cycle only (no chimes). If the trip/reset button is pressed while the vf warning...

  • Page 27

    2. Unplug wiring harness connector under instrument panel. 3. Unhook door strap from the body hook. Be careful not to allow door to swing fully open as mirror may damage paint. 4. With the door open, lift the door to clear hinge pins from their hinges, and remove door. To reinstall the door(s), perf...

  • Page 28

    3. Remove interior b-pillar trim access door at bottom of b-pillar. 4. Unplug wiring harness connector. 5. Unhook door strap from the body hook. 6. With the door open, lift the door to clear hinge pins from their hinges, and remove door. To reinstall the door(s), perform the above steps in the oppos...

  • Page 29

    Door locks the vacuum fluorescent (vf) display located in the odometer area displays the word “door” as an indication of a door ajar or door not completely closed. When the vehicle is not moving and the door is ajar or not completely closed, the vf display will show the word “door.” if any other act...

  • Page 30

    Manual door locks the front (2 door models) and rear doors (4 door models) are equipped with a rocker-type interior door lock. To lock a door when leaving your vehicle, press to the “lock” position (flush) and close the door. Warning! • for personal security reasons and safety in an accident, lock t...

  • Page 31

    Power door locks — if equipped the door lock switch is located on each front door panel. Press the switch downward to lock the doors, and upward to unlock the doors. Warning! • for personal security reasons and safety in an accident, lock the vehicle doors when you drive as well as when you park and...

  • Page 32

    Windows power windows — if equipped the power window switches are located on the instru- ment panel center stack (below the radio). The top left switch controls the left front window and the top right switch controls the right front window. The lower left switch controls the left rear passenger wind...

  • Page 33

    Automatically. To cancel the “auto down” movement, operate the switch in either the up or down direction and release the switch. To stop the window from going all the way down during the auto-down operation, pull up on the switch briefly. To open the window part way, press to the first detent and re...

  • Page 34

    Console. To disable the window controls, press the win- dow lockout button downward. To enable the window controls, press the window lockout button upward. Wind buffeting wind buffeting can be described as the perception of pressure on the ears or a helicopter type sound in the ears. Your vehicle ma...

  • Page 35

    To open the swing gate, press the button on the gate handle. Note: close flip-up window before swing gate (hard top models only). Caution! Do not press on rear wiper blade when closing swing gate, as damage to the blade will result. Warning! Driving with the flip-up window open can allow poisonous e...

  • Page 36

    Occupant restraints some of the most important safety features in your vehicle are the restraint systems. These include the front and rear seat belts for the driver and all passengers, front airbags for both the driver and front passenger, and side airbags (if equipped) for both the driver and front...

  • Page 37

    Inside of the vehicle. Everyone in a motor vehicle should be belted at all times to reduce or prevent injuries. Lap/shoulder belts all seating positions in your vehicle have combination lap/shoulder belts. The belt webbing retractor is de- signed to lock during very sudden stops or collisions. This ...

  • Page 38

    Warning! • wearing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body. These are the strongest parts of your body and take the forces of a collision the best. Wearing your belt in the wrong place could make your injuries in a collision much worse....

  • Page 39

    3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” latch plate latch plate to buckle things to know before starting your vehicle 39 2.

  • Page 40

    Warning! A belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. A belt that is loose will not protect you as well. In a sudden stop you coul...

  • Page 41

    Warning! A lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as pos- sible and keep it snug. A twisted belt cannot do its job as well. In a collision it...

  • Page 42

    Rear center lap/shoulder belt retractor lock-out this feature is designed to lock the retractor whenever the 60% rear seat back is not fully latched. This prevents someone from wearing the rear center lap/shoulder belt when the rear seat back is not fully latched. Note: • if the rear center lap/shou...

  • Page 43

    Adjustable upper shoulder belt anchorage in the front seat positions, the shoulder belt anchorage can be adjusted upward or downward to position the belt away from your neck. Push in on the anchorage near your outside shoulder and slide it up or down to reach the position that serves you best. Warni...

  • Page 44

    Seat belt by assuring that the belt is tight around the occupant early in a collision. Pretensioners work for all size occupants, including those in child restraints. Note: these devices are not a substitute for proper seat belt placement by the occupant. The seat belt must still be worn snugly and ...

  • Page 45

    1. Turn the ignition switch to the off position, and buckle the driver or front passenger seat belt. 2. Turn the ignition key to the accessory/run posi- tion (engine does not need to be running), and wait for the seat belt warning light to turn off. 3. Within 60 seconds of starting the vehicle, unbu...

  • Page 46

    Seat belt extender if a seat belt is too short, even when fully extended and when the adjustable upper shoulder belt anchorage (if equipped) is in its lowest position, your dealer can provide you with a seat belt extender. This extender should be used only if the existing belt is not long enough. Wh...

  • Page 47

    The instrument panel, above the glove compartment. The words srs/airbag are embossed on the airbag covers. Note: the front airbags are certified to the federal regulations that allow less forceful deployment. The front airbags have a multistage inflator design. This may allow the airbag to have diff...

  • Page 48

    Warning! • do not put anything on or around the front airbag covers or attempt to manually open them. You may damage the airbags and you could be injured be- cause the airbags are no longer functional. These protective covers for the airbag cushions are de- signed to open only when the airbags are i...

  • Page 49

    Severe side collisions. In certain types of collisions, both the front and side airbags may be triggered. But even in collisions where the airbags work, you need the seat belts to keep you in the right position for the airbags to protect you properly. Here are some simple steps you can take to minim...

  • Page 50

    4. If your vehicle has side airbags, do not lean against the door, airbags will inflate forcefully into the space be- tween you and the door. 5. If the airbag system in this vehicle needs to be modified to accommodate a disabled person, contact the customer center. Phone numbers are provided under “...

  • Page 51

    Airbag system components the airbag system consists of the following: • occupant restraint control module • airbag warning light • driver airbag • passenger airbag • front seat mounted side airbags (if equipped) • steering wheel and column • instrument panel • interconnecting wiring • knee impact bo...

  • Page 52

    The start or on positions. These include all of the items listed above except the knee bolster, the instru- ment panel, and the steering wheel and column. If the key is in the lock position, in the acc position, or not in the ignition, the airbags are not on and will not inflate. Also, the orc turns...

  • Page 53

    The driver and front passenger when the front passen- ger airbag is turned off. The “pad indicator light” illuminates the words ⬙pass air bag off⬙ to show that the passenger airbag will not inflate during a collision requiring airbags. When the right front pas- senger seat is empty or when very ligh...

  • Page 54

    Adult passenger is properly seated in the front passen- ger seat. In this case, the airbag is ready to be inflated if a collision requiring an airbag occurs. For almost all properly installed rear facing child re- straints, the “pad indicator light” will be illuminated indicating that the front pass...

  • Page 55

    Will cause the system to turn the airbag on. In this case, the ocs has classified the occupant of the seat as an adult. An adult occupant needs to sit in a normal position (with their feet on or near the floor) in order to be properly classified. Reclining the seat back too far may change how an occ...

  • Page 56

    Lodged under the seat and interferes with operation of the weight sensors, a fault will occur which turns on both the “pad indicator light” and the “airbag warning light.” once the lodged object is removed, the fault will be automatically cleared after a short period of time. • the driver and passen...

  • Page 57

    • the side impact (srs) seat mounted side airbags (if equipped) are designed to activate only in certain side collisions. The orc module determines if a side collision is severe enough to require the side airbags to inflate. The orc module monitors the readiness of the electronic parts of the system...

  • Page 58

    • do not use prior or future model year seat covers not designated for the specific model being repaired. Al- ways use the correct seat cover specified for the vehicle. • do not replace the seat cover with an aftermarket seat cover. • do not add a secondary seat cover other than those approved by da...

  • Page 59

    Note: a frontal collision that is not severe enough to need airbag protection will not activate the system. This does not mean something is wrong with the airbag system. If you do have a collision which deploys the airbags, any or all of the following may occur: • the nylon airbag material may somet...

  • Page 60

    Warning! Deployed airbags and seat belt pretensioners cannot protect you in another collision. Have the airbags, seat belt pretensioner, and seat belt retractor assem- bly, replaced by an authorized dealer as soon as possible. Also, have the occupant classification system serviced as well. Enhanced ...

  • Page 61

    Airbag warning light you will want to have the airbag system ready to inflate for your protection in an impact. The airbag system is designed to be maintenance free. If any of the following occurs, have an authorized dealer service the system promptly: • does not come on during the 6 to 8 seconds af...

  • Page 62

    Provided to the custodial entity upon request. General data that does not identify particular vehicles or crashes may be released for incorporation in aggregate crash databases, such as those maintained by the us govern- ment and various states. Data of a potentially sensitive nature, such as would ...

  • Page 63

    Child restraint everyone in your vehicle needs to be buckled up at all times — babies and children, too. Every state in the united states and all canadian provinces require that small children ride in proper restraint systems. This is the law, and you can be prosecuted for ignoring it. Children 12 y...

  • Page 64

    • the infant carrier is only used rearward-facing in the vehicle. It is recommended for children who weigh up to about 20 lbs (9 kg). “convertible” child seats often have a higher weight limit in the rearward-facing direction than infant carriers do, so they can be used rearward-facing by children w...

  • Page 65

    Standards. The manufacturer also recommends that you try a child restraint in the vehicle seats where you will use it before you buy it. • the restraint must be appropriate for your child’s weight and height. Check the label on the restraint for weight and height limits. • carefully follow the instr...

  • Page 66

    • buckle the child into the restraint exactly as the manufacturer’s instructions tell you. • when your child restraint is not in use, secure it in the vehicle with the seat belt or remove it from the vehicle. Do not leave it loose in the vehicle. In a sudden stop or collision, it could strike the oc...

  • Page 67

    • the lap portion should be low on the hips and as snug as possible. • check belt fit periodically. A child’s squirming or slouching can move the belt out of position. • if the shoulder belt contacts the face or neck, move the child closer to the center of the vehicle. Never allow a child to put the...

  • Page 68

    Head restraint and attached to the tether anchor on the rear of the seat back. Then tighten all three straps as you push the child restraint rearward and downward into the seat. Not all child restraint systems will be installed as we have described here. Again, carefully follow the instruc- tions th...

  • Page 69

    Kits or retro-fit kits. You are urged to take advantage of all the available attachments provided with your child re- straint in any vehicle. Note: when using the latch attaching system to install a child restraint, please ensure that all seat belts not being used for occupant restraints are stowed ...

  • Page 70

    Installing the latch-compatible child restraint system we urge that you carefully follow the directions of the manufacturer when installing your child restraint. Not all child restraint systems will be installed as described here. Again, carefully follow the installation instructions that were provi...

  • Page 71

    In addition, there are tether strap anchorages behind each rear seating position located on the back of the seat. Latch anchorages (4 door models) tether strap mounting (2 door models) things to know before starting your vehicle 71 2.

  • Page 72

    Many, but not all restraint systems will be equipped with separate straps on each side, with each having a hook or connector for attachment to the lower anchorage and a means of adjusting the tension in the strap. Forward- facing toddler restraints and some rear-facing infant restraints will also be...

  • Page 73

    Warning! Improper installation of a child restraint to the latch anchorages can lead to failure of an infant or child restraint. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint. Installing child restraints using th...

  • Page 74

    To do something more. Disconnect the latch plate from the buckle, turn the buckle around, and insert the latch plate into the buckle again. If you still can’t make the child restraint secure, try a different seating position. To attach a child restraint tether strap: route the tether strap over the ...

  • Page 75

    Warning! An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchor positions directly behind the child seat to secure a child restraint top tether strap. Transporting pets airbags deploying in the front seat could harm your pet. An...

  • Page 76

    A new engine may consume some oil during its first few thousand miles (kilometers) of operation. This should be considered as a normal part of the break-in and not interpreted as an indication of difficulty. Safety tips exhaust gas warning! Exhaust gases can injure or kill. They contain carbon monox...

  • Page 77

    Side curtains are also open. This will prevent carbon monoxide and other poisonous exhaust gases from entering the vehicle. Safety checks you should make inside the vehicle seat belts inspect the belt system periodically, checking for cuts, frays and loose parts. Damaged parts must be replaced immed...

  • Page 78

    Lights have someone observe the operation of all exterior lights while you work the controls. Check turn signal and high beam indicator lights on the instrument panel. Fluid leaks check area under vehicle after overnight parking for fuel, coolant, oil, or other fluid leaks. Also, if gasoline fumes a...

  • Page 79: Contents

    Understanding the features of your vehicle contents 䡵 mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83 ▫ inside day/night mirror . . . . . . . . . . . . . . . . .83 ▫ outside mirrors . . . . . . . . . . . . . . . . . . . . . . .84 䡵 seats . . . . . . . . . . . . . . . . . . . ...

  • Page 80

    ▫ interior lights . . . . . . . . . . . . . . . . . . . . . . . .94 ▫ multi-function control lever . . . . . . . . . . . . . .96 ▫ parking lights, instrument panel lights, and headlights . . . . . . . . . . . . . . . . . . . . . . . . . . .97 ▫ lights-on reminder . . . . . . . . . . . . . . . . . . ...

  • Page 81

    ▫ tcs (traction control system) . . . . . . . . . . . . 106 ▫ bas (brake assist system) . . . . . . . . . . . . . . . 106 ▫ erm (electronic roll mitigation) . . . . . . . . . . 107 ▫ esp (electronic stability program) . . . . . . . . . 108 ▫ esp/bas warning lamp . . . . . . . . . . . . . . . . 113 䡵...

  • Page 82

    䡵 door frame . . . . . . . . . . . . . . . . . . . . . . . . . . . 167 ▫ door frame removal (2 door models) . . . . . . 167 ▫ door frame installation (2 door models) . . . . 169 ▫ door frame removal (4 door models) . . . . . . 170 ▫ door frame installation (4 door models) . . . . 173 䡵 folding winds...

  • Page 83

    Mirrors inside day/night mirror the mirror should be adjusted to center on the view through the rear window. A two-point pivot system allows for horizontal and vertical adjustment of the mirror. Annoying headlight glare can be reduced by moving the small control under the mirror to the night positio...

  • Page 84

    Outside mirrors to receive maximum benefit, adjust the outside mirror(s) to center on the adjacent lane of traffic with a slight overlap of the view obtained on the inside mirror. Warning! • vehicles and other objects seen in the right side convex mirror will look smaller and farther away than they ...

  • Page 85

    Seats warning! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust any seat only while the vehicle is parked. Front seat adjustment move seat forward ...

  • Page 86

    Manual seat height adjustment — if equipped the driver’s seat height can be raised or lowered, by using the ratcheting handle on the outboard side of the seat. Pull upward on the handle to raise the seat, push downward on the handle to lower the seat. Front seat back recline to recline: 1. Lean forw...

  • Page 87

    Front passenger easy entry seat (2 door models) push the lever on the seatback rearward (toward the rear of the vehicle) to tilt the entire seat forward. Head restraints head restraints can reduce the risk of whiplash injury in the event of impact from the rear. Adjustable head restraints should be ...

  • Page 88

    Fold and tumble rear seat (2 door models) note: prior to folding the rear seat, it may be necessary to reposition the front seats. Also, be sure that the front seats are fully upright and positioned forward. This will allow the rear seat to fold down easily. 1. Lift the seatback release lever and fo...

  • Page 89

    2. Slowly flip the entire seat forward. 3. When completed, return seat to it’s normal position. 4. Raise the rear seatback using the assist strap and firmly lock seat into position. Removing the rear seat (2 door models) warning! • it is extremely dangerous to ride in a cargo area, inside or outside...

  • Page 90

    1. Remove the rear subwoofer (if equipped) mounting screws (3) using a #t30 torx 威 head driver. 2. Unplug electrical connector from rear subwoofer (if equipped). 3. Fold the rear seat forward following steps 1 through 3 under “fold and tumble rear seat” in this section. 4. Press down on release bar ...

  • Page 91

    Replacing the rear seat (2 door models) reverse steps for removing the seat. Warning! • to help protect against personal injury, passen- gers should not be seated in the rear cargo area with the rear seat folded down or removed from the vehicle. • the rear cargo space is intended for load carrying p...

  • Page 92

    To fold down the rear seat 1. Locate the seatback release handle on the outboard top side of each rear seatback; lift up on the handle until the seatback releases. Fold the seatback completely forward. Note: when lifting up on the release handle, the seatback will release easier if you do not pull f...

  • Page 93

    To raise the rear seat 1. Raise the seatback and lock it into place. If interference from the cargo area prevents the seatback from fully locking, you will have difficulty returning the seat to its proper position. Note: if the rear seatback is not fully latched, the center shoulder belt will not be...

  • Page 94

    Have to push down slightly on hood before pushing the handle. Insert the support rod into the slot on the hood panel. To close the hood, remove the support rod from the hood panel and place it in the retaining clip. Lower the hood slowly. Secure both of the hood latches. Warning! If the hood is not ...

  • Page 95

    Cargo lamp courtesy and dome lights are turned on when the front doors are opened, when the dimmer control (rotating wheel on the right side of the switch) is rotated to the upward detent position, or if equipped, when the “un- lock” button is pressed on the key fob. Also, the rear cargo lamp may be...

  • Page 96

    Daytime brightness feature certain instrument panel components (odometer, radio display) can be illuminated at full brightness during the daytime. This can be helpful when driving with your headlights on during the daytime such as in a parade or a funeral procession. To activate this feature, rotate...

  • Page 97

    Parking lights, instrument panel lights, and headlights turn the end of the multi-function control lever to the first detent for parking lights and instrument panel lights. Turn to the second detent for headlight operation. To change the brightness of the instrument panel lights, rotate the center p...

  • Page 98

    Passing light you can signal another vehicle with your headlights by lightly pulling the multi-function control lever toward the steering wheel. This will cause the headlights to turn on at high beam and remain on until the lever is released. Front fog lights — if equipped the front fog light switch...

  • Page 99

    Daytime running lights — if equipped the headlights come on at a low intensity level after the vehicle has been driven approximately 3 feet (1 meter). They will turn off when the vehicle is turned off or when the headlights are switched on. Windshield wipers and washers caution! In cold weather, alw...

  • Page 100

    Windshield wiper operation move the lever upward to the second detent for lo speed wiper operation, or to the third detent for hi speed operation windshield washers to use the washer, pull the lever toward you and hold while spray is desired. If the lever is pulled while in the delay range, the wipe...

  • Page 101

    Tilt steering column to tilt the column, push down on the lever under the multi-function control lever and move the wheel up or down, as desired. Pull the lever back upwards to lock the column firmly in place. Warning! Tilting the steering column while the vehicle is moving is dangerous. Without a s...

  • Page 102

    Electronic speed control — if equipped when engaged, this device takes over the accelerator operation at speeds greater than 35 mph (56 km/h). The speed control lever is located on the right side of the steering wheel. To activate push the on/off button. The cruise indicator in the instrument cluste...

  • Page 103

    To set at a desired speed when the vehicle has reached the desired speed, press down on the lever and release. Release the accelerator and the vehicle will operate at the selected speed. Note: the vehicle should be traveling at a steady speed and on level ground before pressing the set lever. To dea...

  • Page 104

    Tapping the “set decel” button once will result in a 1 mph (2 km/h) speed decrease. Each time the button is tapped, speed decreases. Manual transmission depressing the clutch pedal will disengage the speed control. A slight increase in engine rpm before the speed control disengages is normal. Vehicl...

  • Page 105

    On steep hills, a greater speed loss or gain and/or more frequent downshifts (auto transmission only) may occur so it may be preferable to drive without speed control. Electronic brake control system your vehicle is equipped with an advanced electronic brake control system that includes abs (anti-lo...

  • Page 106

    Tcs (traction control system) this system monitors the amount of wheel spin of each of the driven wheels. If wheel spin is detected, brake pressure is applied to the slipping wheel(s) to provide enhanced acceleration and stability. A feature of the tcs system functions similar to a limited slip diff...

  • Page 107

    Warning! Bas (brake assist system) cannot prevent the natu- ral laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions. Bas cannot prevent accidents, in- cluding those resulting from excessive speed in turns, driving on very slippery surfa...

  • Page 108

    Note: anytime the esp system is in the “full off” mode, erm is disabled. Refer to esp (electronic stability program) for a complete explanation of the available esp modes. Warning! Many factors, such as vehicle loading, road condi- tions and driving conditions, influence the chance that wheel lift o...

  • Page 109

    • understeer - when the vehicle is turning less than appropriate for the steering wheel position. The ⬙esp/tcs indicator light⬙ located in the instrument cluster, starts to flash as soon as the tires lose traction and the esp system becomes active. The ⬙esp/tcs indicator light ⬙ also flashes when tc...

  • Page 110

    High range (4wd models) or 2wd models on this is the normal operating mode for esp in 4wd high range and in 2wd vehicles. Whenever the vehicle is started or the transfer case (if equipped) is shifted from 4wd low range or neutral back to 4wd high range, the esp system will be in this mode. This mode...

  • Page 111

    Gravel, it may be desirable to switch to the “partial off” mode by pressing the esp switch. Once the situation requiring esp to be switched to the “partial off” mode is overcome, turn esp back on by momentarily depressing the “esp control switch”. This may be done while the vehicle is in motion. Esp...

  • Page 112

    Warning! With the esp switched off, the enhanced vehicle stability offered by esp and erm are unavailable. In an emergency evasive maneuver, the esp and erm systems will not engage to assist in maintaining stability. The “full off” esp mode is intended for off-highway or off-road use only. 4wd low r...

  • Page 113

    Warning! With the esp switched off, the enhanced vehicle stability offered by esp and erm are unavailable. In an emergency evasive maneuver, the esp and erm systems will not engage to assist in maintaining stability. The “full off” mode is intended for off- highway or off-road use only. Esp/bas warn...

  • Page 114

    Electrical power outlet this vehicle has two auxiliary power outlets that can provide up to 20 amps of current for accessories de- signed for use with the standard power outlet adapters. The outlet located in the lower portion of the instrument panel has a snap on plastic cap so that it can be cover...

  • Page 115

    Electrical outlet use with engine off warning! • many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.E. Cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or p...

  • Page 116

    The rear passengers have cup holders at the rear of the center console. Storage console storage compartment to lock or unlock, insert ignition key and turn. To open, press the latch and lift cover. Rear cup holders center console 116 understanding the features of your vehicle.

  • Page 117

    Rear storage compartment the rear storage compartment cover is held by a spring loaded latch. In order to remove the rear storage com- partment cover, use the following procedure: note: the rear storage compartment latch should not be used as cargo tie-down. 1. Flip up pull loop so it is perpendicul...

  • Page 118

    Dual top — if equipped if your vehicle is equipped with a dual top, you must remove one of the tops from the vehicle. If the soft top is removed, the pivot brackets must also be removed from the sport bar. The soft top was installed at the factory for shipping purposes only. The soft top and the har...

  • Page 119

    3. Remove the soft top bow assembly pivot bracket screws (2 per side) using a #t30 torx 威 head driver. 4. Using a rubber mallet, carefully tap the knuckles from the left and right metal pivot brackets. Remove the soft top from the vehicle and store in a clean, dry location. Understanding the feature...

  • Page 120

    5. Unzip the zipper on the sport bar cover to expose the pivot brackets. Remove the brackets using a #t30 torx 威 head driver. Recover and re-zip the sports bar cover. Store pivot brackets and screws in a safe place. 6. Reinstall the hard top. Refer to “hard top — hard top installation” in this secti...

  • Page 121

    4. If the soft top has been removed, follow these steps to reinstall the soft top. If the soft top is on the vehicle, proceed to step #5. A. If the pivot brackets have been removed, unzip the sport bar covers and attach the pivot brackets to the sports bar with the 4 screws that were removed using a...

  • Page 122

    C. Tap the knuckles on the side with a rubber mallet to reattach them to the metal pivot brackets. D. Screw the pivot screws back into place using a #t30 torx 威 head driver. Secure them until they are snug being careful not to cross-thread the screws or over tighten. Caution! Do not overtighten the ...

  • Page 123

    5. Unsnap and remove the black boot cover. This cover should be discarded. It was intended as a protective cover for shipping only. Note: a visual instruction sheet is enclosed in the dual top wrap. 6. Remove the swing gate bar (black metal bar for bottom of rear window) located in the soft top and ...

  • Page 124

    Caution! Do not move your vehicle until the top has been either fully attached to the windshield frame and bodyside, or fully removed. Front panel(s) removal note: left panel must be removed before removing right panel. 1. Fold down the sun visor, and move to the side. 2. Turn center dials (2) from ...

  • Page 125

    3. Turn rear dial (located above shoulder belt anchorage). 4. Turn rear fastener (knob) (located on overhead speaker bar assembly). Understanding the features of your vehicle 125 3.

  • Page 126

    5. Unlatch the header panel latch located at the top of the windshield. 6. Remove panel. To remove right panel, follow steps above except for step 2. Front panel(s) installation note: the front panel (s) must be positioned properly to ensure sealing. Set the panels on the windshield frame so that th...

  • Page 127

    4. Unbolt the torx 威 head screws (4 for 2 door models) (6 for 4 door models) which secure the hard top to the vehicle using a #40 torx 威 head driver. 5. Open swing gate all the way to ensure clearance of the rear window glass. Lift rear window glass. 6. Locate the wiring harness at the rear left sid...

  • Page 128

    7. Disconnect the washer hose and install the tethered cap. Caution! Make sure storage cap is installed to prevent foreign materials from entering tube and clogging system. 8. Disconnect the wire harness from the hard top by pressing the tab at the side of the connector and pulling to disconnect. No...

  • Page 129

    9. Remove the hard top from the vehicle. Place on a soft surface to prevent damage. Rear panel installation note: if the door frames are installed from soft top usage, they must be removed prior to installation of the hard top. 1. Inspect the hard top seals for damage and replace if necessary. 2. In...

  • Page 130

    Soft top (2 door models) caution! • the soft top is not designed to carry any addi- tional loads such as roof racks, spare tires, build- ing, hunting, or camping supplies, and/or lug- gage, etc. Also, it was not designed as a structural member of the vehicle, and thus cannot properly carry any addit...

  • Page 131

    Caution! • do not run a fabric top through an automatic car wash. Window scratches and wax build up may result. • do not lower the top when the temperature is below 41°f (5°c). Damage to the top may result. • do not move your vehicle until the top has been either fully attached to the windshield fra...

  • Page 132

    Etc., clean them with a mild soap solution and a small brush. Cleaning products are available through your authorized dealer. 1. If your vehicle has half doors, remove each half door window by opening the door and lifting the half door window out. Note: stow half doors carefully outside of the vehic...

  • Page 133

    4. Release the header latches and leave the hooks in the loops on the windshield. 5. Open the swing gate. 6. Untuck the first three (3) inches of both sail panels, and pull the swing gate bar straight rearward out of the swing gate brackets (prior to unzipping the window). Understanding the features...

  • Page 134

    • unzip the rear window starting at the right lower corner of the window. Pull the zipper up, across the top and down to the left lower corner. Zipper pulls will stay on the rear window. Pull down on the rear window to disengage from the zipper on the top cover. Stow the windows carefully to avoid s...

  • Page 135

    10. Remove the bottom retainers of the sail panels from the body side retainer at the rear corners of the vehicle. Note: it is helpful to pull down on the 3 bow. 11. As you begin to lower the top, fold the sail panels so that they rest on top of the soft top. Understanding the features of your vehic...

  • Page 136

    12. The swing gate brackets do not need to be removed unless the hard top is being installed. To remove the swing gate brackets, pull the front side of clip forward and up to disengage from the bodyside retainer. 13. Completely release the latches from the loops on the windshield frame. 136 understa...

  • Page 137

    14. Grasp the side bow behind the header, lift the top, and fold toward the rear of the vehicle. 15. Tuck the fabric and the check straps between the bows and as far inward as possible. This will keep any portion of the top from flapping outside of the vehicle. When the top is completely down, posit...

  • Page 138

    Putting up the soft top 1. Unclip and move the sun visors to the side. 2. Standing on the side of the vehicle, lift the top by the side bow and the 2–bow (middle bow) up and over the sports bar until the header rests on the top of the windshield frame. 3. Before attaching the header latches, be sure...

  • Page 139

    5. If the swing gate brackets were removed, install them by hooking the front edge on the body side retainer and rotate it downward until it snaps onto the rail. Ensure that the clips are properly located. 6. Move to the rear of the vehicle and gently pull the sail panels over the 3 bow. Understandi...

  • Page 140

    7. Tuck the sail panel retainers into the bodyside retainer. It may be necessary to pull down slightly at the top of the 3 bow to bring the retainers into place. 8. To install the quarter window, affix the upper rear corner of the window temporarily to the velcro 威. Start and zip the zipper only abo...

  • Page 141

    9. Tuck the front retainer into the door frame slot. Ensure that the retainer is fully rolled around and properly positioned into the door frame. Failure to do so will result in possible damage along with wind and water leaks. 10. Continue zipping the window to the upper rear corner. Understanding t...

  • Page 142

    11. Tuck the bottom retainer of the quarter window into the bottom retainer, beginning at the front and working to the rear of the vehicle. Finish zipping the window and attach the velcro 威 along the top and rear of the window. Repeat this step for the other side. 12. If the sail panel is fully inst...

  • Page 143

    14. Install the rear window by starting both zipper ends at the lower left corner of the rear window opening. Ensure that the zippers are properly started and aligned before zipping to prevent damage. 15. Run the zipper fully around to the right side of the window. 16. Finish installing the sail pan...

  • Page 144

    19. Open the doors and tuck the plastic retainers into the door frame slots above the door opening. Start at the front and work toward the rear of the vehicle. 20. Close the header latches and return the sun visors to their secured position. 144 understanding the features of your vehicle.

  • Page 145

    Soft top (4 door models) caution! • the soft top is not designed to carry any addi- tional loads such as roof racks, spare tires, build- ing, hunting, or camping supplies, and/or lug- gage, etc. Also, it was not designed as a structural member of the vehicle, and thus cannot properly carry any addit...

  • Page 146

    Caution! • do not run a fabric top through an automatic car wash. Window scratches and wax build up may result. • do not lower the top when the temperature is below 41°f (5°c). Damage to the top may result. • do not lower the top when the windows are dirty. Grit may scratch the window. • do not move...

  • Page 147

    Etc., clean them with a mild soap solution and a small brush. Cleaning products are available through your authorized dealer. 1. If your vehicle has half doors, remove each half door window by opening the door and lifting the half door window out. Note: stow half doors carefully outside of the vehic...

  • Page 148

    4. Release the header latches and hooks from the loops on the windshield frame. 5. Open the swing gate. 6. Untuck the first three (3) inches of both sail panels, and pull the swing gate bar straight rearward out of the swing gate brackets (prior to unzipping the window). 148 understanding the featur...

  • Page 149

    • unzip the rear window starting at the right lower corner of the window. Pull the zipper up, across the top and down to the left lower corner. Zipper pulls will stay on the rear window. Pull down on the rear window to disengage from the zipper on the top cover. Stow the windows carefully to avoid s...

  • Page 150

    10. Remove the bottom retainers of the sail panels from the body side retainer at the rear corners of the vehicle. Note: it is helpful to pull down on the 4 bow. 11. Fold the sail panels so that they rest on top of the soft top. 150 understanding the features of your vehicle.

  • Page 151

    12. The swing gate brackets do not need to be removed unless the hard top is being installed. To remove the swing gate brackets, pull the front side of clip forward and up to disengage from the bodyside retainer. 13. Grasp the front side bow behind the header, and lift the top. Understanding the fea...

  • Page 152

    14. Fold back the front section of the top, and gently rest the header on top of the rear portion of the deck. 15. Fold the top material so that the plastic retainers form a “w” as shown. Enter the vehicle, and move the material into two folds. 152 understanding the features of your vehicle.

  • Page 153

    16. Release the side bows by pressing down on the latch above the front of the rear door. Push the top rearward to disengage. Repeat this step on the other side. 17. Grasp the folded side bows and slide the top along the door frame track to the rear door frame. Understanding the features of your veh...

  • Page 154

    18. Gently slide the side bows off the door frame track and lower the top down into the vehicle. 19. Tuck the fabric and the check straps between the bows as far inside as possible. This will keep any portion of the top from flapping outside of the vehicle. 20. Once the top is fully down, use the st...

  • Page 155

    Putting up the soft top note: be extremely careful when putting up the soft top to prevent the doors from getting scratched. It may be helpful to open the rear doors. 1. Undo the straps used to secure the top in the down position and store in secure location. 2. Open the swing gate. 3. Grasp the fol...

  • Page 156

    4. Engage the slider feature of the knuckles into the door frame tracks and slide the top forward. 5. Ensure that the top locks into sunrider locking mecha- nisms that are located above the front of the rear doors. 6. Unclip and move the sun visors to the side. 156 understanding the features of your...

  • Page 157

    7. Standing on the side of the vehicle, lift the top by the side bow until it rests on the windshield frame. 8. Before attaching the header latches, be sure the drip retainers above the door opening are not trapped be- tween the top and the door frame. 9. Open the header latches and engage the hook ...

  • Page 158

    10. If the swing gate brackets were removed, install them by hooking the front edge on the body side retainer and rotate it downward until it snaps onto the rail. Ensure that the clips are properly located. 11. Move to the rear of the vehicle and gently pull the sail panels over the 4 bow. 12. Tuck ...

  • Page 159

    13. To install the quarter window, affix the upper rear corner of the window temporarily to the velcro 威. Start and zip the zipper only about 1 inch (2.5 cm). At this time it is necessary to tuck in the door frame retainer. 14. Tuck the front retainer into the door frame slot. Ensure that the retain...

  • Page 160

    15. Continue zipping the window to the upper rear corner. 16. Tuck the bottom retainer of the quarter window into the bottom retainer, beginning at the front and working to the rear of the vehicle. Finish zipping the window and attach the velcro 威 along the top and rear of the window. Repeat this st...

  • Page 161

    18. Locate the black swing gate bar. Slide the swing gate bar over the receiver at the bottom inside of the rear window, with the bulky seal away from you. 19. Install the rear window by starting both zipper ends at the lower left corner of the rear window opening. Ensure that the zippers are proper...

  • Page 162

    22. Grasp the swing gate bar and position it into the swing gate brackets. 23. Completely tuck the sail panel into the bodyside retainer. 24. Open the doors and tuck the plastic retainers into the door frame slots above the door opening. Start at the front and work toward the rear of the vehicle. 16...

  • Page 163

    25. Ensure plastic retainer is tucked in properly at b-pillar not pinching seal. 26. Close the header latches and return the sun visors to their secured position. Sunrider — 4 door models note: if you are going to be driving faster than 40 mph (64 km/h) with the sunrider feature open, it is recom- m...

  • Page 164

    To open 1. Above the front of the rear door, place finger up into the cut out in the plastic retainer and pull down rolling both the front and rear retainers out of the door frame. Repeat this on the other side. 2. Unclip and move the sun visors to the side. 3. Release the header latches from the lo...

  • Page 165

    4. Grasp the front side bow behind the header, and lift the top. 5. Fold back the front section of the top, and gently rest the header on top of the rear portion of the deck. Understanding the features of your vehicle 165 3.

  • Page 166

    6. Fold the top material so that the plastic retainers form a “w” as shown. Enter the vehicle, and move the material into two folds. Ensure that the straps are securely stowed. 7. Secure the top by using the two (2) provided straps. Each strap will wrap around the side bow and velcro 威 to itself, us...

  • Page 167

    Door frame warning! Do not drive your vehicle on-pavement with the door frame removed as you lose the protection these structural elements can provide. This procedure is furnished for use during off-road operation only. Door frame removal (2 door models) 1. Unscrew and remove the door frame attachme...

  • Page 168

    2. Place one hand on the upper rear and one hand on the front of the door frame. 3. Pull the frame towards you with your rearward hand to remove the frame from the vehicle. 4. Screw the knobs back into the door frame and fold for storage. Store in a secure location. Warning! Never store the door fra...

  • Page 169

    Door frame installation (2 door models) 1. Unfold door frame and unscrew thumbscrews. 2. Set the door frame pin into the hole on top of the body side, behind the door opening. 3. After the door frame pin has been set into the bodys- ide hole, carefully set the front of the door frame into the rubber...

  • Page 170

    5. Starting with the front knob, screw in and tighten both knobs. Repeat on the other side. Door frame removal (4 door models) 1. Unscrew and remove the two (2) forward most door frame attachment knobs. 170 understanding the features of your vehicle.

  • Page 171

    Warning! Use both hands to remove the door frames. The door frames will fold and could cause injury if both hands are not used. 2. Place one hand on the upper rear and one hand on the upper front of the front door frame. 3. Pull the frame towards you with your front hand to remove the frame from the...

  • Page 172

    4. Unscrew and remove the remaining door frame at- tachment knob on the rear door frame. 5. Place one hand on the upper rear and one hand on the upper front of the rear door frame. Pull the frame towards you with your rear hand to remove the frame from the vehicle. 172 understanding the features of ...

  • Page 173

    6. Screw the knob back into the door frame and fold for storage. Store in a secure location. Warning! • never store the door frames in your vehicle. In an event of an accident, a loose door frame many cause personal injury. If removed, always store the door frames outside of the vehicle. Door frame ...

  • Page 174

    2. Set the door frame pin into the hole on top of the body side, just behind the rear door opening. 3. Position the top of the door frame against the metal sport bar and press onto the side bar making sure not to pinch the material of the sports bar covers and to ensure it is properly positioned on ...

  • Page 175

    Door frame. Position the rear of the front door frame to lay on top of the front of the rear door frame. 6. Loosely install both knobs beginning with the front knob (long knob). Then, install the middle knob (short knob) through the front and rear door frames and screw into the top of the b-pillar. ...

  • Page 176

    Folding windshield the fold down windshield and removable side bars on your vehicle are structural elements that can provide some protection in some accidents. The windshield also provides some protection against weather, road debris and intrusion of small branches and other objects. Do not drive yo...

  • Page 177

    Warning! Carefully follow these warnings to help protect against personal injury: • do not drive your vehicle on-road with the wind- shield down. • do not drive your vehicle unless the windshield is securely fastened, either up or down. • eye protection, such as goggles, should be worn at all times ...

  • Page 178

    2. Remove the 2 top hex bolts (13mm), and the 1 side hex bolt (13mm) visible through the trim (do not remove plastic corner trim, sun visor bolts, or sport bar covering). 3. Open sport bar velcro covering. 4. Remove 1 hex bolt (13mm) visible through the plastic trim on bottom side of side bar, 1 hex...

  • Page 179

    Caution! Do not remove the head impact foam from the side bars, as damage to the foam may result. Note: store all of the mounting bolts in their original threaded holes and tighten for safekeeping. 5. Remove side bar assembly, and reattach sport bar velcro covering. 6. To safely store the side bars ...

  • Page 180

    8. Remove the lower windshield plates by removing the 6 black round headed torx 威 head screws (using a #40 torx 威 head driver) on each side of the base of the windshield. 9. Lower the windshield gently until it contacts the rubber hood bumpers. 10. Secure the windshield by passing a cinch strap thro...

  • Page 181

    2. Loosely attach rear of side bar to sport bar. Refer to step 4 of “lowering windshield and removing side bars” earlier in this section. • reattach sport bar velcro covering. 3. Attach front of side bar to windshield frame. • install top two (2) hex bolts (13mm) first, then lower side hex bolt (13m...

  • Page 182

    5. Install the lower windshield plates with the 6 black round headed torx 威 head screws (using a #40 torx威 head driver) on each side of the base of the windshield. 6. Reinstall wiper arms. Rear window features — hard top only rear window wiper/washer — if equipped a rotary ring switch on the control...

  • Page 183

    If the rear wiper is operating when the ignition is turned off, the wiper will automatically return to the “park” position. When the vehicle is restarted, the wiper will resume function at whichever position the switch is set at. If the swing gate flip-up window is open or the swing gate is open, co...

  • Page 184

    Level at regular intervals. Fill the reservoir with wind- shield washer solvent (not radiator antifreeze) and oper- ate the system for a few seconds to flush out the residual water. Rear window defroster — if equipped the push-button is located on the bottom right side of the blower control knob. Pr...

  • Page 185: Contents

    Understanding your instrument panel contents 䡵 instrument panel and controls . . . . . . . . . . . . . 188 䡵 instrument cluster . . . . . . . . . . . . . . . . . . . . . . 189 䡵 instrument cluster description . . . . . . . . . . . . . 190 䡵 compass and trip computer — if equipped . . . 198 ▫ control...

  • Page 186

    ▫ notes on playing mp3/wma files . . . . . . . . 214 ▫ list button (disc mode for mp3/wma play) . . . . . . . . . . 217 ▫ info button (disc mode for mp3/wma play) . . . . . . . . . . 217 䡵 sales code res — am/fm stereo radio with cd player (mp3 aux jack) . . . . . . . . . . . . . . . . . . . 219 ▫ o...

  • Page 187

    䡵 cd/dvd disc maintenance . . . . . . . . . . . . . . . 237 䡵 radio operation and cellular phones . . . . . . . . 237 䡵 climate controls . . . . . . . . . . . . . . . . . . . . . . . 238 ▫ manual heater only . . . . . . . . . . . . . . . . . . . 238 ▫ manual air conditioning and heating system — if ...

  • Page 188

    Instrument panel and controls 188 understanding your instrument panel.

  • Page 189

    Instrument cluster understanding your instrument panel 189 4.

  • Page 190

    Instrument cluster description your vehicle is equipped with the instrument cluster described on the following pages. 1. Fuel gauge the pointer shows the level of fuel in the fuel tank. When the fuel gauge pointer initially moves to e, for your safety, approximately 2 u.S. Gallons (7.6l) of fuel rem...

  • Page 191

    7. Seat belt indicator light a warning chime and an indicator light will alert you to buckle the seat belts. When the belt is buckled, the chime will stop, but the light will stay on until it times out (about 6 seconds). 8. Turn signal indicator lights the arrows will flash with the exterior turn si...

  • Page 192

    If the parking brake is applied and the vehicle is in motion, the red brake warning light will “flash” and a chime will sound. The operation of the brake warning light can be checked by turning the ignition switch from the off position to the on position. The light should illuminate for approximatel...

  • Page 193

    Caution! Do not operate the engine with the tachometer pointer in the red area. Engine damage will occur. 16. Engine coolant temperature warning light this light warns of an overheated engine condi- tion. If the engine is critically hot, a warning chime will sound 10 times. After the chime turns off...

  • Page 194

    22. Transmission range indicator this display indicator shows the automatic transmission gear selection. 23. Tire pressure monitoring telltale light — if equipped each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by t...

  • Page 195

    And off for 60 seconds when a system fault is detected. The flash cycle will repeat every ten minutes or until the fault condition is removed and reset. Caution! The tpms has been optimized for the original equipment tires and wheels. Tpms pressures and warnings have been established for the tire si...

  • Page 196

    Stays on through several typical driving styles. In most situations, the vehicle will drive normally and will not require towing. When the engine is running, the “malfunction indicator light” may flash to alert serious conditions that could lead to immediate loss of power or severe catalytic convert...

  • Page 197

    Engine running, a malfunction has been detected in either the esp or the bas system. If this light stays illuminated, have the esp and bas checked at your authorized dealer as soon as possible. Refer to “electronic brake control system” in section 5 for more information. 30. Electronic throttle cont...

  • Page 198

    Compass and trip computer — if equipped this feature, located on the instrument cluster (speedom- eter and tachometer), displays information on outside temperature, compass direction, and trip information. The compass/trip computer, when the appropriate con- ditions exist, will show the following me...

  • Page 199

    Press and hold the left button (on the instrument cluster) for 2 to 3 seconds to switch from english to metric displays. Reset press and hold the right button (on the instrument cluster) while function is being displayed to reset. The following trip conditions can be reset: • avg eco (changes to pre...

  • Page 200

    Trip a shows the total distance traveled for trip a since the last reset. Trip b shows the total distance traveled for trip b since the last reset. Compass temperature display this display provides the outside temperature and one of eight compass readings to indicate the direction the vehicle is fac...

  • Page 201

    After initial calibration, the compass will continue to automatically update this calibration whenever the ve- hicle is in motion. Manual compass calibration note: before attempting a manual compass calibra- tion, the engine must be running and the transmission in the p (park) position (if equipped)...

  • Page 202

    Symbol appears. The current variance value will also be displayed. To change the zone, press the left button once to increment the zone. The default is zone 8. After zone 15, the values will wrap around to zone 1. When the correct zone is displayed (per the zone map) for the zone that the vehicle is...

  • Page 203

    Outside temperature if the outside temperature is more than 131°f (55°c), the display will show 131°f (55°c). When the outside tem- perature is less than ⫺40°f (⫺40°c), the display will show ⫺40°f (⫺40°c). Radio general information radio broadcast signals your new radio will provide excellent recept...

  • Page 204

    Fm reception because fm transmission is based on frequency varia- tions, interference that consists of amplitude variations can be filtered out, leaving the reception relatively clear, which is the major feature of fm radio. Note: the radio, steering wheel radio controls (if equipped), and 6 disc cd...

  • Page 205

    Power switch/volume control (rotary) press the on/vol control to turn the radio on. Press the on/vol a second time to turn off the radio. Electronic volume control the electronic volume control turns continuously (360 degrees) in either direction without stopping. Turning the volume control to the r...

  • Page 206

    2. Adjust the hours by turning the right side tune control knob. 3. After the hours are adjusted, press the right side tune control knob to set the minutes. The minutes will begin to blink. 4. Adjust the minutes using the right side tune control knob. Press the tune control knob to save time change....

  • Page 207

    Press the rotary tune control knob a fifth time and fade will display. Turn the tune control knob to the left or right to adjust the sound level between the front and rear speakers. Press the rotary tune control knob again to exit setting tone, balance and fade. Music type button (radio mode) pressi...

  • Page 208

    Program type 16 digit-character display religious music rel musc religious talk rel talk rock rock soft soft soft rock soft rck soft rhythm and blues soft r&b sports sports talk talk top 40 top 40 weather weather by pressing the seek button when the music type icon is displayed, the radio will be tu...

  • Page 209

    • dvd play options - selecting the dvd play options will display the following: • subtitle – repeatedly pressing select will switch subtitles to different subtitle languages that are available on the disc (if equipped). • audio stream – repeatedly pressing select will switch to different audio langu...

  • Page 210

    A language not listed, then scroll down and select ⬙other⬙. Enter the 4 digit country code using the tune control knob to scroll up and down to select the # and then push to select. Audio language — if equipped selecting this item will allow the user to choose a default audio language (effective onl...

  • Page 211

    Autoplay — if equipped when this is set to on and a dvd video is inserted, it will bypass the dvd menu screen and automatically play the movie. In some rare cases, the dvd player may not auto play the main title. In such cases, use the menu button on the remote control to select desired title to pla...

  • Page 212

    Buttons 1 - 6 (radio mode) these buttons tune the radio to the stations that you commit to push-button memory {12 am, 12 fm, and 12 satellite (if equipped) stations}. Disc button pressing the disc button will allow you to switch from am/fm modes to disc modes. Operation instructions - (disc mode for...

  • Page 213

    Radio display will show ⬙loading disc⬙ when the disc is loading and “reading disc” when the radio is reading the disc. Caution! • this cd player will accept 4 3/4 inch (12 cm) discs only. The use of other sized discs may damage the cd player mechanism. Eject button — ejecting compact disc(s) press t...

  • Page 214

    Rw/ff (cd mode) press and hold ff (fast forward) and the cd player will begin to fast forward until ff is released or rw or another cd button is pressed. The rw (reverse) button works in a similar manner. Am or fm button (cd mode) switches the radio to the radio mode. Rnd button (random play button)...

  • Page 215

    • maximum number of directory levels: 8 • maximum number of files: 255 • maximum number of folders: 100 • maximum number of characters in file/folder names: • level 1: 12 (including a separator ⬙.⬙ and a 3-character extension) • level 2: 31 (including a separator ⬙.⬙ and a 3-character extension) mul...

  • Page 216

    Mpeg specifi- cation sampling fre- quency (khz) bit rate (kbps) mpeg-1 audio layer 3 48, 44.1, 32 320, 256, 224, 192, 160, 128, 112, 96, 80, 64, 56, 48 mpeg-2 audio layer 3 24, 22.05, 16 160, 128, 144, 112, 96, 80, 64, 56, 48 wma specifica- tion sampling fre- quency (khz) bit rate (kbps) wma 44.1 an...

  • Page 217

    List button (disc mode for mp3/wma play) pressing the list button will bring up a list of all folders on the disc. Scrolling up or down the list is done by turning the tune control knob. Selecting a folder by pressing the tune control knob will begin playing the files contained in that folder (or th...

  • Page 218

    Scan button (auxiliary mode) no function. Eject button (auxiliary mode) no function. Pscan button (auxiliary mode) no function. Time button (auxiliary mode) press this button to change the display from elapsed playing time to time of day. The time of day will be displayed for 5 seconds. Rw/ff (auxil...

  • Page 219

    Macrovision this product incorporates copyright protection technol- ogy that is protected by u.S. Patents and other intellec- tual property rights. Use of this copyright protection technology must be authorized by macrovision, and is intended for home and other limited viewing uses only unless other...

  • Page 220

    Power switch/volume control (rotary) press the on/volume control knob to turn the radio on. Press the on/volume control knob a second time to turn the radio off. Electronic volume control the electronic volume control turns continuously (360 degrees) in either direction without stopping. Turning the...

  • Page 221

    2. Adjust the hours by turning the right side tune control knob. 3. After the hours are adjusted, press the right side tune control knob to set the minutes. The minutes will begin to blink. 4. Adjust the minutes using the right side tune control knob. Press the tune control knob to save time change....

  • Page 222

    Press the rotary tune control knob a fifth time and fade will display. Turn the tune control knob to the left or right to adjust the sound level between the front and rear speakers. Press the rotary tune control knob again to exit setting tone, balance and fade. Music type button pressing this butto...

  • Page 223

    Program type 16 digit-character display religious music rel musc religious talk rel talk rock rock soft soft soft rock soft rck soft rhythm and blues soft r&b sports sports talk talk top 40 top 40 weather weather by pressing the seek button when the music type icon is displayed, the radio will be tu...

  • Page 224

    Select the button (1-6) you wish to lock onto this station and press and release that button. If a button is not selected within 5 seconds after pressing the set button, the station will continue to play but will not be stored into push-button memory. You may add a second station to each push-button...

  • Page 225

    Inserting compact disc(s) gently insert one cd into the cd player with the cd label facing up. The cd will automatically be pulled into the cd player and the cd icon will illuminate on the radio display. If a cd does not go into the slot more than an inch, a disc may already be loaded and must be ej...

  • Page 226

    If you have ejected a disc and have not removed it within 10 seconds, it will be reloaded. If the cd is not removed, the radio will reinsert the cd but will not play it. A disc can be ejected with the radio and ignition off. Note: ejecting with ignition off is not allowed on convertible or soft-top ...

  • Page 227

    Press the right seek button to move to the next ran- domly selected track. Press the rnd button a second time to stop random play. Notes on playing mp3 files the radio can play mp3 files, however, acceptable mp3 file recording media and formats are limited. When writing mp3 files, pay attention to t...

  • Page 228

    • level 2: 31 (including a separator ⬙.⬙ and a 3-character extension) multisession disc formats are supported by the radio. Multisession discs may contain combinations of normal cd audio tracks and computer files (including mp3 files). Discs created with an option such as ⬙keep disc open after writi...

  • Page 229

    Playback of mp3 files when a medium containing mp3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the mp3 files. Loading times for playback of mp3 files may be affected by the following: • med...

  • Page 230

    Press and hold the info button again for 3 seconds to return to ⬙elapsed time⬙ display. Operation instructions - auxiliary mode the auxiliary (aux) jack is an audio input jack, which allows the user to plug in a portable device such as an mp3 player, or cassette player, and utilize the vehicle’s aud...

  • Page 231

    Sales code rer — am/fm/cd/dvd radio with navigation system — if equipped note: the radio sales code is located on the lower right side of your radio faceplate. Satellite navigation radio with cd player with mp3 capability (rer) - combines a global-positioning system-based navigation system with an i...

  • Page 232

    Either the h button on the faceplate to change the hour or the m button on the faceplate to change the minute. 2. The time setting will increase each time you press the button. Holding either button in will fast forward the setting. 3. If no changes are made within 5 seconds of accessing the setup s...

  • Page 233

    Satellite radio — if equipped satellite radio uses direct satellite to receiver broadcast- ing technology to provide clear digital sound, coast to coast. The subscription service provider is sirius™ satel- lite radio. This service offers up to 100 channels of music, sports, news, entertainment, and ...

  • Page 234

    Number will be displayed. The sirius id number display will time out in 2 minutes. Press any button on the radio to exit this screen. Selecting satellite mode (rsc radios) press the sat button until ⬙sat⬙ appears in the display. A cd may remain in the radio while in the satellite radio mode. Satelli...

  • Page 235

    Seek buttons press and release the seek buttons to search for the next channel in satellite mode. Press the right switch to seek up and the left switch to seek down. The radio will remain tuned to the new channel until you make another selection. Holding either button will bypass channels without st...

  • Page 236

    If a preset button is activated while in the music type (program type) mode, the music type mode will be exited and the radio will tune to the preset channel. Setup button pressing the setup button allows you to select the following items: • display sirius id number — press the select button to disp...

  • Page 237

    Operating instructions - hands free phone (if equipped) refer to hands free phone in section 3 of the owner’s manual. Operating instructions - video entertainment system (ves 姞) (if equipped) refer to separate video entertainment system (ves 威) guide. Cd/dvd disc maintenance to keep the cd/dvd discs...

  • Page 238

    Climate controls manual heater only the controls for the heating/ventilation system in this vehicle consist of a series of rotary knobs. These comfort controls can be set to obtain desired interior conditions. Mode control the mode control (left rotary knob) allows you to choose from several pattern...

  • Page 239

    Floor air is directed through the floor outlets and side window demist outlets with a small amount through the defrost outlet. Mix air is directed through the floor, defrost and side window demist outlets. This setting works best in cold or snowy conditions that require extra heat at the windshield....

  • Page 240

    Manual air conditioning and heating system — if equipped the controls for the heating/air conditioning and venti- lation system in this vehicle consist of a series of rotary knobs. These comfort controls can be set to obtain desired interior conditions. The instrument panel features four airflow reg...

  • Page 241

    Panel air is directed through the outlets in the instrument panel. These outlets can be adjusted to direct air flow. Bi-level air is directed through the panel and floor outlets. Note: there is a difference in temperature between the upper and lower outlets for added comfort. The warmer air goes to ...

  • Page 242

    Blower control use this control to regulate the amount of air forced through the system in any mode you select. The fan speed increases as you move the control to the right from the off position. Temperature control use this control to regulate the temperature of the air in- side the passenger compa...

  • Page 243

    Circulation control press this button to choose between outside air intake or recirculation of the air inside the vehicle. A lamp will illu- minate when you are in “re- circulate” mode. Only use the “recirculate” mode to tempo- rarily block out any outside odors, smoke, or dust and to cool the inter...

  • Page 244

    Operating tips window fogging windows will fog on the inside when the humidity inside the vehicle is high. This often occurs in mild or cool temperatures when it’s rainy or humid. In most cases turning on the air-conditioning (pressing the snowflake button) will clear the fog. Adjust the temperature...

  • Page 245

    Winter operation when operating the system during the winter months, make sure the air intake, located directly in front of the windshield, is free of ice, slush, snow, or other obstruc- tions. Vacation storage anytime you store your vehicle, or keep it out of service (i.E. Vacation) for two weeks o...

  • Page 247: Starting And Operating

    Starting and operating contents 䡵 starting procedures . . . . . . . . . . . . . . . . . . . . . 251 ▫ manual transmission . . . . . . . . . . . . . . . . . . 251 ▫ automatic transmission . . . . . . . . . . . . . . . . 251 ▫ normal starting . . . . . . . . . . . . . . . . . . . . . . 251 ▫ extreme c...

  • Page 248

    ▫ shift positions . . . . . . . . . . . . . . . . . . . . . . . . 267 ▫ shifting procedure . . . . . . . . . . . . . . . . . . . . 268 䡵 trac-lok™ rear axle — if equipped . . . . . . . . . 269 䡵 axle lock (tru–lok™) — rubicon models . . . . . 270 䡵 rear axle lock — 4wd non-rubicon models (if equippe...

  • Page 249

    ▫ radial-ply tires . . . . . . . . . . . . . . . . . . . . . . 297 ▫ tire spinning . . . . . . . . . . . . . . . . . . . . . . . . 297 ▫ tread wear indicators . . . . . . . . . . . . . . . . . . 298 ▫ life of tire . . . . . . . . . . . . . . . . . . . . . . . . . 298 ▫ replacement tires . . . . . . ...

  • Page 250

    ▫ trailer towing weights (maximum trailer weight ratings) . . . . . . . . . 320 ▫ trailer and tongue weight . . . . . . . . . . . . . . 324 ▫ towing requirements . . . . . . . . . . . . . . . . . . 325 ▫ towing tips . . . . . . . . . . . . . . . . . . . . . . . . . 330 䡵 recreational towing (behind ...

  • Page 251

    Starting procedures before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. Warning! Never leave children alone in a vehicle. Leaving children in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriousl...

  • Page 252

    Tip start feature — automatic transmission only do not press the accelerator. Turn the ignition key briefly to start position, and release it. The starter motor will continue to run, but will automatically disengage itself when the engine is running. Extreme cold weather (below –20°f or –29°c) to in...

  • Page 253

    Warning! Never pour fuel or other flammable liquids into the throttle body air inlet opening in an attempt to start the vehicle. This could result in a flash fire causing serious personal injury. Warning! Do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automat...

  • Page 254

    Warning! Never leave children alone in a vehicle. Leaving children in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Do not leave the keys in the ignition. A child could operate power windows, other controls, or move the vehicle. E...

  • Page 255

    Manual transmission 6-speed manual transmission warning! You or others could be injured if you leave the vehicle unattended without having the parking brake fully applied. The parking brake should al- ways be applied when the driver is not in the vehicle, especially on an incline. Follow the shift p...

  • Page 256

    Warning! When parking your vehicle, always leave a manual transmission in first gear and apply the parking brake fully to guard against vehicle movement and possible injury or damage. Never use any gear as a substitute for the parking brake. Caution! To drive as safely as possible and to prolong the...

  • Page 257

    • when “rocking” a stuck vehicle by shifting between a forward gear and reverse, do not spin wheels faster than 15 mph (24 km/h), or drivetrain damage may result. Recommended manual transmission shifting speeds the manufacturer recommends that you use the shift speeds listed in the chart below. Manu...

  • Page 258

    Caution! Failure to follow the recommended downshifting speeds may cause the engine to over speed and/or damage the clutch disc even if the clutch pedal is depressed. Automatic transmission caution! Damage to the transmission may occur if the follow- ing precautions are not observed: • shift into p ...

  • Page 259

    Warning! It is dangerous to shift the selector lever out of p (park) or n (neutral) if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in reverse. You could lose control of the vehicle and hit someone or somet...

  • Page 260

    4. Using the screwdriver, reach into the manual override opening. Press and hold the shift lock lever down. 5. Depress the shifter release button and shift into n (neutral). 6. The vehicle may then be started in n (neutral). Have your vehicle inspected by your local authorized dealer, if the shift l...

  • Page 261

    Automatic transmission with overdrive shifting from d (drive) to p (park) or r (reverse) (or from p or r to d) should be done only after the accelerator pedal is released and the vehicle is stopped. Be sure to keep your foot on the brake when moving the shift lever between these gears. Gear ranges d...

  • Page 262

    Warning! It is dangerous to shift the selector lever out of p (park) or n (neutral) if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in reverse. You could lose control of the vehicle and hit someone or somet...

  • Page 263

    Strong head winds, or trailer towing), turning off over- drive will improve performance and extend transmission life by reducing excessive shifting and heat buildup. Overdrive can be locked out by pressing the o/d off switch located on the center console. The o/d off indicator light (on the switch) ...

  • Page 264

    Warning! Never use p (park) position with an automatic trans- mission as a substitute for the parking brake. Al- ways apply parking brake fully when parked to guard against vehicle movement and possible injury or damage. Caution! • before moving the shift lever out of p (park), you must turn the ign...

  • Page 265

    Clutch within the torque converter engages automatically at calibrated speeds. This may result in a slightly differ- ent feeling or response during normal operation in high gear. When the vehicle speed drops or during accelera- tion, the clutch automatically and smoothly disengages. Four–wheel drive...

  • Page 266

    And rear wheels to rotate at the same speed. This is accomplished by simply moving the shift lever to these positions. The 4h and 4l positions are intended for loose, slippery road surfaces only. Driving in the 4h and 4l positions on dry hard surfaced roads may cause in- creased tire wear and damage...

  • Page 267

    Warning! You or others could be injured if you leave the vehicle unattended with the transfer case in the n (neutral) position without first fully engaging the parking brake. The transfer case n (neutral) position disengages both the front and rear driveshafts from the powertrain and will allow the ...

  • Page 268

    4l position four wheel drive low range — locks the front and rear driveshafts together. Forces the front and rear wheels to rotate at the same speed. Additional traction and maxi- mum pulling power for loose, slippery road surfaces only. Do not exceed 25 mph (40 km/h). The “4wd indicator light” (loc...

  • Page 269

    Method is with the vehicle rolling at 2 to 3 mph (3 to 5 km/h). Avoid attempting to engage or disengage 4l with the vehicle moving faster than 2 to 3 mph (3 to 5 km/h). Warning! Failure to engage a position completely can cause transfer case damage or loss of power and vehicle control. You could hav...

  • Page 270

    Axle lock (tru–lok™) — rubicon models the axle lock switch is located on the lower switch bank (below the climate controls). This feature will only activate when the following con- ditions are met: • key in ignition, vehicle in 4l (low) range. • vehicle speed should be 10 mph (16 km/h) or less. To a...

  • Page 271

    Rear axle lock — 4wd non-rubicon models (if equipped) the rear axle lock switch is located on the lower switch bank (below the climate controls). This feature will only activate when the following con- ditions are met: • key in ignition, vehicle in 4l (low) range. • vehicle speed should be 10 mph (1...

  • Page 272

    Press the sway bar switch to activate the system. Press the switch again to deactivate the system. The “sway bar indicator light” (located in the instrument cluster) will illuminate when the bar is disconnected. The “sway bar indicator light” will flash during activation transition, or when activati...

  • Page 273

    Obtain the off-road position. The amber indicator light will flash until the stabilizer/sway bar has been fully disconnected. Note: the stabilizer/sway bar may be torque locked due to left and right suspension height differences. This condition is due to driving surface differences or vehicle loadin...

  • Page 274

    They are not designed for cornering at the same speeds as conventional 2-wheel drive vehicles any more than low- slung sports cars are designed to perform satisfactorily in off-road conditions. If at all possible, avoid sharp turns or abrupt maneuvers. As with other vehicles of this type, failure to...

  • Page 275

    3. Remove side step assembly. When to use 4l (low) range when off-road driving, shift to 4l (low) for additional traction and control on slippery or difficult terrain, ascending or descending steep hills, and to increase low speed pulling power. This range should be limited to extreme situations suc...

  • Page 276

    Driving through water more than a few inches deep will require extra caution to ensure safety and prevent dam- age to your vehicle. If you must drive through water, try to determine the depth and the bottom condition (and location of any obstacles) prior to entering. Proceed with caution and maintai...

  • Page 277

    Do not shift to a lower gear than necessary to maintain headway. Over-revving the engine can spin the wheels and traction will be lost. Avoid abrupt downshifts on icy or slippery roads, be- cause engine braking may cause skidding and loss of control. Hill climbing note: before attempting to climb a ...

  • Page 278

    Turning the front wheels slowly left and right. This may provide a fresh “bite” into the surface and will usually provide traction to complete the climb. Traction downhill shift the transmission into a low gear and the transfer case to 4l (low) range. Let the vehicle go slowly down the hill with all...

  • Page 279

    • after extended operation in mud, sand, water, or similar dirty conditions, have brake rotors, wheels, brake linings, and axle yokes inspected and cleaned as soon as possible. Warning! Abrasive material in any part of the brakes may cause excessive wear or unpredictable braking. You might not have ...

  • Page 280

    Be sure the parking brake is firmly set when parked, and the gear shift lever is in the p (park) position (automatic transmission) or r (reverse) or 1st gear (manual trans- mission). When parking on a hill, you should apply the parking brake before placing the gear shift lever in p (park), otherwise...

  • Page 281

    When parking on a hill, turn the front wheels toward the curb on a downhill grade and away from the curb on an uphill grade. The parking brake should always be applied whenever the driver is not in the vehicle. Anti-lock brake system the anti-lock brake system is designed to aid the driver in mainta...

  • Page 282

    During off-road use, loss of traction can temporarily defeat the system and cause the warning light to illumi- nate. Turn the ignition off and on again to restore anti-lock brake system function. Warning! Pumping of the anti-lock brakes will diminish their effectiveness and may lead to an accident. ...

  • Page 283

    Caution! The anti-lock brake system is subject to possible detrimental effects of electronic interference caused by improperly installed aftermarket radios or tele- phones. Note: during severe braking conditions, a pulsing sensation may occur and a clicking noise will be heard. This is normal, indic...

  • Page 284

    Warning! Continued operation with reduced power steering assist could pose a safety risk to yourself and others. Service should be obtained as soon as possible. Caution! Prolonged operation of the steering system at the end of the steering wheel travel will increase the steering fluid temperature an...

  • Page 285

    Note: • p(passenger)-metric tire sizing is based on u.S. Design standards. P-metric tires have the letter “p” molded into the sidewall preceding the size designation. Ex- ample: p215/65r15 95h. • european metric tire sizing is based on european design standards. Tires designed to this standard have ...

  • Page 286

    Tire sizing chart example: size designation: p = passenger car tire size based on u.S. Design standards ⴖ....Blank....ⴖ = passenger car tire based on european design standards lt = light truck tire based on u.S. Design standards t = temporary spare tire 31 = overall diameter in inches (in) 215 = sec...

  • Page 287

    Example: service description: 95 = load index —a numerical code associated with the maximum load a tire can carry. H = speed symbol —a symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions. —the maximum speed corresp...

  • Page 288

    Tire identification number (tin) the tin may be found on one or both sides of the tire however the date code may only be on one side. Tires with white sidewalls will have the full tin including date code located on the white sidewall side of the tire. Look for the tin on the outboard side of black s...

  • Page 289

    Tire loading and tire pressure tire placard location tire placard location (2 door models) tire placard location (4 door models) starting and operating 289 5.

  • Page 290

    Tire and loading information placard this placard tells you important information about the, 1) number of people that can be carried in the vehicle 2) the total weight your vehicle can carry 3) the tire size designed for your vehicle 4) the cold tire inflation pressures for the front, rear and spare...

  • Page 291

    Combined weight of occupants, cargo/luggage and trailer tongue weight (if applicable) should never exceed the weight referenced here. Steps for determining correct load limit 1. Locate the statement “the combined weight of occu- pants and cargo should never exceed xxx pounds” on your vehicle’s placa...

  • Page 292

    292 starting and operating.

  • Page 293

    Warning! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. Tires — general information tire pressure proper tire inflation pressur...

  • Page 294

    2. Economy— improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Under inflation also increases tire rolling resistance and results in higher fuel consump- t...

  • Page 295

    The pressure should be checked and adjusted as well as inspecting for signs of tire wear or visible damage at least once a month. Use a good quality pocket-type gauge to check tire pressure. Do not make a visual judgement when determining proper inflation. Radial tires may look properly inflated eve...

  • Page 296

    Tire pressures change by approximately 1 psi (7 kpa) per 12° f (7° c) of air temperature change. Keep this in mind when checking tire pressure inside a garage especially in the winter. Example: if garage temperature = 68° f (20° c) and the outside temperature = 32° f (0° c) then the cold tire inflat...

  • Page 297

    Radial-ply tires warning! Combining radial ply tires with other types of tires on your vehicle will cause your vehicle to handle poorly. The instability could cause an accident. Al- ways use radial tires in sets of four. Never combine them with other types of tires. Cuts and punctures in radial tire...

  • Page 298

    Tread wear indicators tread wear indicators are in the original equipment tires to help you in determining when your tires should be replaced. These indicators are molded into the bottom of the tread grooves and will appear as bands when the tread depth becomes 1/16 inch (2 mm). When the indicators ...

  • Page 299

    Keep unmounted tires in a cool, dry place with as little exposure to light as possible. Protect tires from contact with oil, grease and gasoline. Replacement tires the tires on your new vehicle provide a balance of many characteristics. They should be inspected regularly for wear and correct cold ti...

  • Page 300

    Caution! Replacing original tires with tires of a different size may result in false speedometer and odometer read- ings. Alignment and balance poor suspension alignment may result in: • fast tire wear. • uneven tire wear, such as feathering and one-sided wear. • vehicle pull to right or left. Tires...

  • Page 301

    • install chains snugly and tighten after.6 mile (1 km) of driving. • do not exceed 30 mph (48 km/h). • drive cautiously, avoiding large bumps, potholes and extreme driving maneuvers. Tire rotation recommendations tires on the front and rear axles of vehicles operate at different loads and perform d...

  • Page 302

    Tire pressure monitor system (tpms) — if equipped the tire pressure monitoring system (tpms) will warn the driver of a low tire pressure based on the vehicle recommended cold placard pressure. The tire pressure will vary with temperature by about 1 psi (6.9 kpa) for every 12°f (6.5°c). This means th...

  • Page 303

    (241 kpa). If the ambient temperature is 65°f (18°c) and the measured tire pressure is 30 psi (207 kpa), a tempera- ture drop to 20°f (-7°c) will decrease the tire pressure to approximately 26 psi (179 kpa). This tire pressure is sufficiently low enough to turn on the “tire pressure monitoring tellt...

  • Page 304

    The four active road tire pressures are low. The audible chime will sound once every ignition cycle for each condition that it detects. Should this occur, you should stop as soon as possible, check the inflation pressure of each tire on your vehicle, and inflate each tire to the pressure recommended...

  • Page 305

    Caution! The tpms has been optimized for the original equipment tires and wheels. Tpms pressures have been established for the tire size equipped on your vehicle. Undesirable system operation or sensor damage may result when using replacement equip- ment that is not of the same size, type, and/or st...

  • Page 306

    • the tpms is not a substitute for proper tire mainte- nance, and it is the driver’s responsibility to maintain correct tire pressure, even if under-inflation has not reached the level to trigger illumination of the “tire pressure monitoring telltale light.” general information this device complies ...

  • Page 307

    Over 40 auto manufacturer’s world wide have issued and endorsed consistent gasoline specifications (the world- wide fuel charter, wwfc) to define fuel properties necessary to deliver enhanced emissions, performance, and durability for your vehicle. The manufacturer recom- mends the use of gasoline t...

  • Page 308

    Manufacturer. While mtbe is an oxygenate made from methanol, it does not have the negative effects of metha- nol. Mmt in gasoline mmt is a manganese containing metallic additive that is blended into some gasoline to increase the octane num- ber. Gasolines blended with mmt offer no performance advant...

  • Page 309

    • the use of leaded gasoline is prohibited by federal law. Using leaded gasoline can impair engine perfor- mance, damage the emission control system. • an out-of-tune engine, or certain fuel or ignition malfunctions, can cause the catalytic converter to overheat. If you notice a pungent burning odor...

  • Page 310

    The vehicle is raised. Have any abnormal conditions repaired promptly. Until repaired, drive with all side windows fully open. • keep the swing gate closed when driving your vehicle to prevent carbon monoxide and other poisonous exhaust gases from entering the vehicle. Adding fuel fuel filler cap (g...

  • Page 311

    Caution! Damage to the fuel system or emission control system could result from using an improper fuel cap (gas cap). A poorly fitting cap could let impurities into the fuel system. Also, a poorly fitting after- market cap can cause the mil (malfunction indica- tor light) to illuminate, due to fuel ...

  • Page 312

    Note: tighten the gas cap about 1/4 turn until you hear one click. This is an indication that cap is properly tightened. If the gas cap is not tighten properly, the malfunction indicator light will come on. Be sure the gas cap is tightened every time the vehicle is refueled. Warning! A fire may resu...

  • Page 313

    Vehicle loading certification label as required by national highway traffic safety admin- istration regulations, your vehicle has a certification label affixed to the driver’s side door or pillar. This label contains the month and year of manufacture, gross vehicle weight rating (gvwr), gross axle w...

  • Page 314

    Tire size the tire size on the label represents the actual tire size on your vehicle. Replacement tires must be equal to the load capacity of this tire size. Rim size this is the rim size that is appropriate for the tire size listed. Inflation pressure this is the cold tire inflation pressure for yo...

  • Page 315

    Improper weight distributions can have an adverse effect on the way your vehicle steers and handles and the way the brakes operate. Caution! Do not load your vehicle any heavier than the gvwr or the maximum front and rear gawr. If you do, parts on your vehicle can break, or it can change the way you...

  • Page 316

    Gross trailer weight (gtw) the gross trailer weight (gtw) is the weight of the trailer plus the weight of all cargo, consumables and equipment (permanent or temporary) loaded in or on the trailer in its ⬙loaded and ready for operation⬙ condition. The recom- mended way to measure gtw is to put your f...

  • Page 317

    Frontal area the maximum height and maximum width of the front of a trailer. Trailer sway control the trailer sway control is a telescoping link that can be installed between the hitch receiver and the trailer tongue that typically provides adjustable friction associated with the telescoping motion ...

  • Page 318

    Warning! An improperly adjusted weight distributing hitch system may reduce handling, stability, braking per- formance, and could result in an accident. Weight distributing systems may not be compatible with surge brake couplers. Consult with your hitch and trailer manufacturer or a reputable recrea...

  • Page 319

    Trailer hitch classification the following chart provides the industry standard for the maximum trailer weight a given trailer hitch class can tow and should be used to assist you in selecting the correct trailer hitch for your intended towing condition. Refer to the trailer towing weights (maximum ...

  • Page 320

    Trailer towing weights (maximum trailer weight ratings) the following chart provides the maximum trailer weight ratings towable for your given drivetrain. Engine/ transmis- sion axle model gcwr (gross combined wt. Rat- ing) frontal area max. Gtw (gross trailer wt.) max. Tongue wt. (see note 1) 3.8l/...

  • Page 321

    3.8l/ manual 4.10 2 door sahara model (4wd) 6,101 lbs (2 767 kg) 25 sq. Ft. (2.32 square meters) 2,000 lbs (907 kg) 200 lbs (91 kg) 3.8l/ automatic 4.10 2 door sahara model (4wd) 6,126 lbs (2 779 kg) 25 sq. Ft. (2.32 square meters) 2,000 lbs (907 kg) 200 lbs (91 kg) 3.8l/ manual 4.10 2 door rubicon ...

  • Page 322

    3.8l/ manual 4.10 4 door x model (2wd) 7,514 lbs (3 408 kg) 32 sq. Ft. (2.97 square meters) 3,500 lbs (1 587 kg) 350 lbs (159 kg) 3.8l/ automatic 4.10 4 door x model (2wd) 7,539 lbs (3 420 kg) 32 sq. Ft. (2.97 square meters) 3,500 lbs (1 587 kg) 350 lbs (159 kg) 3.8l/ manual 3.21 4 door sahara model...

  • Page 323

    3.8l/ manual 3.21 4 door x model (4wd) 5,225 lbs (2 370 kg) 32 sq. Ft. (2.97 square meters) 1,000 lbs (453 kg) 100 lbs (45 kg) 3.8l/ manual 4.10 4 door x model (4wd) 7,725 lbs (3 504 kg) 32 sq. Ft. (2.97 square meters) 3,500 lbs (1 587 kg) 350 lbs (159 kg) 3.8l/ automatic 4.10 4 door x model (4wd) 7...

  • Page 324

    3.8l/ automatic 4.10 4 door sahara model (4wd) 7,944 lbs (3 603 kg) 32 sq. Ft. (2.97 square meters) 3,500 lbs (1 587 kg) 350 lbs (159 kg) 3.8l/ manual 4.10 4 door rubicon model (4wd) 7,965 lbs (3 613 kg) 32 sq. Ft. (2.97 square meters) 3,500 lbs (1 587 kg) 350 lbs (159 kg) 3.8l/ automatic 4.10 4 doo...

  • Page 325

    Which will cause loss of control of vehicle and trailer. Failure to load trailers heavier in front is the cause of many trailer accidents. Consider the following items when computing the weight on the rear axle of the vehicle: • the tongue weight of the trailer. • the weight of any other type of car...

  • Page 326

    Note: trailer towing requires special rear axle lubri- cant. Refer to “fluids, lubricants, and genuine parts” in section 7 for more information. Caution! • avoid towing a trailer for the first 500 miles (805 km) of vehicle operation. Doing so may damage your vehicle. Perform the maintenance listed i...

  • Page 327

    • safety chains must always be used between your vehicle and trailer. Always connect the chains to the frame or hook retainers of the vehicle hitch. Cross the chains under the trailer tongue and allow enough slack for turning corners. • vehicles with trailers should not be parked on a grade. When pa...

  • Page 328

    − check for signs of tire wear or visible tire damage before towing a trailer. Refer to the tires–general information section of this manual on tread wear indicators for the proper inspection procedure. − when replacing tires, refer to the tires–general infor- mation section of this manual on replac...

  • Page 329

    Warning! Do not connect trailer brakes to your vehicle’s hy- draulic brake lines. It can overload your brake sys- tem and cause it to fail. You might not have brakes when you need them and could have an accident. Towing any trailer will increase your stopping dis- tance. When towing you should allow...

  • Page 330

    Towing tips before setting out on a trip, practice turning, stopping and backing the trailer in an area away from heavy traffic. If using a manual transmission vehicle for trailer towing, all starts must be in first gear to avoid excessive clutch slippage. Towing tips — automatic transmission the “d...

  • Page 331

    Note: check the automatic transmission fluid level before towing. Towing tips — o/d off (if equipped) to reduce potential for automatic transmission overheat- ing, turn the “o/d off” feature off when driving in hilly areas or shift the transmission to drive position 2 on more severe grades. Refer to...

  • Page 332

    Recreational towing (behind motorhome, etc.) caution! Front or rear wheel lifts should not be used. Internal damage to the transmission or transfer case will occur if a front or rear wheel lift is used when recreational towing. Note: the transfer case must be shifted into n (neu- tral) for recreatio...

  • Page 333

    7. Shut the engine off and place the ignition key into the unlocked off position. 8. Shift automatic transmission into p (park). 9. Apply parking brake. 10. Attach vehicle to the tow vehicle with tow bar. 11. Release parking brake. Caution! Damage to the transmission may occur if the trans- mission ...

  • Page 334

    Warning! You or others could be injured if you leave the vehicle unattended with the transfer case in the n (neutral) position without first fully engaging the parking brake. The transfer case n (neutral) position disengages both the front and rear driveshafts from the powertrain and will allow the ...

  • Page 335: Contents

    What to do in emergencies contents 䡵 hazard warning flashers . . . . . . . . . . . . . . . . . 336 䡵 if your engine overheats . . . . . . . . . . . . . . . . . 337 䡵 jacking and tire changing . . . . . . . . . . . . . . . . 338 ▫ jack location . . . . . . . . . . . . . . . . . . . . . . . . 338 ▫ sp...

  • Page 336

    Hazard warning flashers your vehicle’s hazard warning flasher is an emergency warning system. When you activate it, all front and rear directional signals will flash intermittently. Use it when your vehicle is disabled on or near the road. It warns other drivers to steer clear of you and your vehicl...

  • Page 337

    If your engine overheats in any of the following situations, you can reduce the potential for overheating by taking the appropriate ac- tion. • on the highways — slow down. • in city traffic — while stopped, put transmission in n (neutral), but do not increase engine idle speed. Note: there are step...

  • Page 338

    Jacking and tire changing warning! • getting under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never get any part of your body under a vehicle that is on a jack. If you need to get under a raised vehicle, take it to a service center wh...

  • Page 339

    Spare tire stowage to remove the spare tire from the carrier, remove the tire cover, if equipped, and remove the lug nuts with the lug wrench turning them counterclockwise. Note: if you have added aftermarket accessories to the spare tire mounted carrier, it cannot exceed a gross weight of 50 lbs (2...

  • Page 340

    Jacking instructions 1. Remove spare tire, jack and tools from stored location. 2. Loosen (but do not remove) the wheel lug nuts by turning them to the left one turn while the wheel is still on the ground. 3. Assemble the jack and jacking tools. Connect jack handle driver to extension, then to lug w...

  • Page 341

    5. Raise the vehicle by turning the jack screw to the right. Raise the vehicle only until the tire just clears the surface and enough clearance is obtained to install the spare tire. Minimum tire lift provides maximum stability. Warning! Raising the vehicle higher than necessary can make the vehicle...

  • Page 342

    Warning! A loose tire or jack, thrown forward in a collision or hard stop could endanger the occupants of the ve- hicle. Always stow the jack parts and the spare tire in the places provided. 11. Secure the tire, jack, and tools in their proper loca- tions. Jump starting if the vehicle has a discharg...

  • Page 343

    2. Park the booster vehicle within cable reach but with- out letting the vehicles touch. Set the parking brake on both vehicles, place the automatic transmission in p (park), or the manual transmission in n (neutral), and turn the ignition off. 3. Turn off the heater, radio, and all unnecessary elec...

  • Page 344

    6. Start the engine in the vehicle which has the booster battery, let the engine idle a few minutes, then start the engine in the vehicle with the discharged battery. 7. When removing the jumper cables, reverse the above sequence exactly. Be careful of the moving belts and fan. Warning! Any procedur...

  • Page 345

    Warning! Stand clear of vehicles when pulling with tow hooks. Tow straps and chains may break, causing serious injury. Towing a disabled vehicle the manufacturer recommends towing with all four wheels off the ground. Acceptable methods are to tow the vehicle on a flatbed or with one end of the vehic...

  • Page 347: Maintaining Your Vehicle

    Maintaining your vehicle contents 䡵 engine compartment – 3.8l . . . . . . . . . . . . . . . 350 䡵 onboard diagnostic system — obd ii . . . . . . . . 351 ▫ loose fuel filler cap message . . . . . . . . . . . . 351 䡵 emissions inspection and maintenance programs . . . . . . . . . . . . . . . . . . . 3...

  • Page 348

    ▫ power steering fluid check . . . . . . . . . . . . . . 363 ▫ driveline and steering component lubrication . . . . . . . . . . . . . . . . . 364 ▫ body lubrication . . . . . . . . . . . . . . . . . . . . . 364 ▫ windshield wiper blades . . . . . . . . . . . . . . . . 365 ▫ windshield washers . . . ...

  • Page 349

    ▫ center high mounted stop light (chmsl) . . . 397 䡵 fluid capacities . . . . . . . . . . . . . . . . . . . . . . . . 397 䡵 fluids, lubricants and genuine parts . . . . . . . . 398 ▫ engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 398 ▫ chassis . . . . . . . . . . . . . . . . . . . ...

  • Page 350

    Engine compartment – 3.8l 350 maintaining your vehicle.

  • Page 351

    Onboard diagnostic system — obd ii your vehicle is equipped with a sophisticated onboard diagnostic system called obd ii. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide ex...

  • Page 352

    Cap until a ⬙clicking⬙ sound is heard. This is an indication that the gas cap is properly tightened. Press the odometer reset button to turn the message off. If the problem persists, the message will appear the next time the vehicle is started. This might indicate a damaged cap. If the problem is de...

  • Page 353

    4. As soon as you turn your key to the on position, you will see your mil symbol come on as part of a normal bulb check. 5. Approximately 15 seconds later, one of two things will happen: a. The mil will flash for about 10 seconds and then return to being fully illuminated until you turn off the igni...

  • Page 354

    Dealer service your dealer has the qualified service personnel, special tools, and equipment to perform all service operations in an expert manner. Service manuals are available which include detailed service information for your vehicle. Refer to these manuals before attempting any procedure yourse...

  • Page 355

    Checking the oil while the vehicle is on level ground will improve the accuracy of the oil level readings. Always maintain the oil level within the safe zone on the dipstick. Adding one quart of oil when the reading is at the bottom of the safe zone will result in a reading at the top of the safe zo...

  • Page 356

    • more than 50% of your driving is at sustained high speeds during hot weather, above 90°f (32°c) • taxi, police, or delivery service (commercial service) • trailer towing • off-road or desert driving • if equipped for and operating with e–85 (ethanol) fuel if any of these apply to you, then change ...

  • Page 357

    Engine oil viscosity (3.8l engines) sae 5w-20 engine oil is recommended for all operating temperatures. This engine oil improves low tempera- ture starting and vehicle fuel economy. Your engine oil filler cap shows the recommended engine oil viscosity for your vehicle. Lubricants which do not have b...

  • Page 358

    Drive belts — check condition and tension belt tension is controlled by means of an automatic tensioner. No belt tension adjustments are required. However, belt and belt tensioner condition should be inspected at the specified intervals, and replaced if re- quired. See your authorized dealer for ser...

  • Page 359

    Caution! Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition. In the event of engine malfunction, particularly involv- ing engine misfire or other apparent loss of perfor- mance, have your vehicle serviced promptly. Contin- ued operation of your veh...

  • Page 360

    • do not shut off the engine or interrupt the ignition when the transmission is in gear and the vehicle is in motion. • do not try to start the engine by pushing or towing the vehicle. • do not idle the engine with any spark plug wires disconnected or removed, such as when diagnostic testing. • do n...

  • Page 361

    Engine air cleaner filter under normal driving conditions, replace the air filter at the intervals shown on “maintenance schedule a.” if, however, you drive the vehicle frequently under dusty or severe conditions, the filter element should be inspected periodically and replaced if necessary at the i...

  • Page 362

    To determine the battery charge, check the battery test indicator (if equipped) on top of the battery. Refer to the illustration. Caution! It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negat...

  • Page 363

    Warning! • use only refrigerants and compressor lubricants approved by the manufacturer for your air condi- tioning system. Some unapproved refrigerants are flammable and can explode, injuring you. Other unapproved refrigerants or lubricants can cause the system to fail, requiring costly repairs. Re...

  • Page 364

    Warning! Fluid level should be checked on a level surface with the engine off to prevent injury from moving parts, and to insure accurate fluid level reading. Do not overfill. Use only the manufacturer’s recommended fluid. If necessary, add fluid to restore to the proper indicated level. With a clea...

  • Page 365

    Amount of a high quality lubricant such as mopar 威 lock cylinder lubricant directly into the lock cylinder. Windshield wiper blades clean the rubber edges of the wiper blades and the windshield periodically with a sponge or soft cloth and a mild non-abrasive cleaner. This will remove accumula- tions...

  • Page 366

    Exhaust system the best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system. If you notice a change in the sound of the exhaust system; or if the exhaust fumes can be detected inside the vehicle; or when the underside or rear of the vehicle i...

  • Page 367

    Garden hose vertically down the face of the a/c con- denser (if equipped) or the back of the radiator core. Check the engine cooling system hoses for brittle rubber, cracking, tears, cuts, and tightness of the connection at the coolant recovery bottle and radiator. Inspect the entire system for leak...

  • Page 368

    Caution! • mixing of antifreeze/coolant other than the speci- fied hoat antifreeze/coolant may result in de- creased corrosion protection and engine damage. If a non-hoat antifreeze/coolant is introduced into the cooling system in an emergency, it should be replaced with the specified antifreeze/coo...

  • Page 369

    Use only high purity water such as distilled or deionized water when mixing the water/antifreeze (coolant) solu- tion. The use of lower quality water will reduce the amount of corrosion protection in the engine cooling system. Please note that it is the owner’s responsibility to main- tain the prope...

  • Page 370

    Children, do not store ethylene glycol based antifreeze/ coolant in open containers or allow it to remain in puddles on the ground. If ingested by a child, contact a physician immediately. Clean up any ground spills im- mediately. Engine coolant level the coolant bottle provides a quick visual metho...

  • Page 371

    Coolant needs to be added, contents of coolant recov- ery bottle must also be protected against freezing. • if frequent antifreeze/coolant additions are required, or if the level in the recovery bottle does not drop when the engine cools, the cooling system should be pressure tested for leaks. • mai...

  • Page 372

    Are present. Components should be replaced immedi- ately if there is any evidence of degradation that could cause failure. Brake system in order to assure brake system performance, all brake system components should be inspected periodically. Refer to the appropriate “maintenance schedule” in sectio...

  • Page 373

    Warning! Worn brake hoses can burst and cause brake failure. You could have an accident. If you see any signs of cracking, scuffing, or worn spots, have the brake hoses replaced immediately. Brake master cylinder the fluid level in the master cylinder should be checked when performing under hood ser...

  • Page 374

    Use only brake fluid that has been in a tightly closed container to avoid contamination from foreign matter. Do not allow petroleum base fluid to contaminate the brake fluid as seal damage will result. Automatic transmission selection of lubricant it is important that the proper lubricant is used in...

  • Page 375

    Check the fluid level while the transmission is at normal operating temperature 180° f (82° c). This occurs after at least 15 mi (25 km) of driving. At normal operating temperature the fluid cannot be held comfortably be- tween the fingertips. To properly check the automatic transmission fluid level...

  • Page 376

    Caution! Be aware that if the fluid temperature is below 50° f (10° c), it may not register on the dipstick. Do not add fluid until the temperature is elevated enough to produce an accurate reading. 7. Check for leaks. Release the parking brake. Note: to prevent dirt and water from entering the tran...

  • Page 377

    Frequency of fluid change under normal operating conditions, the fluid installed at the factory will give satisfactory lubrication for the life of the vehicle. Fluid changes are not necessary unless the lubricant has become contaminated with water. If con- taminated with water, the fluid should be c...

  • Page 378

    Caution! When replacing plugs, do not overtighten. You could damage them and cause them to leak. Selection of lubricant use only manufacturer’s recommended fluid, refer to fluids, lubricants, and genuine parts for correct fluid type. Front/rear axle fluid fluid level check lubricant should be at bot...

  • Page 379

    Damage to fuel lines, brake hoses, axle pinion seals, and propeller shafts. Check air conditioning drain tube on the lower dash wall in the engine compartment for mud or debris, and clean as required. A plugged tube will adversely affect air conditioning performance. Caution! Under frequent heavy-du...

  • Page 380

    • insects, tree sap and tar. • salt in the air near sea-coast localities. • atmospheric fallout/industrial pollutants. • bird droppings. Washing • wash your vehicle regularly. Always wash your ve- hicle in the shade using mopar 威 car wash or a mild car wash soap, and rinse the panels completely with...

  • Page 381

    • if you detect any stone chips or scratches in the paint, touch them up immediately. The cost of such repairs is considered the responsibility of the owner. • if your vehicle is damaged due to an accident or similar cause which destroys the paint and protective coating have your vehicle repaired as...

  • Page 382

    • for tough stains, apply mopar威 total clean or a mild soap solution to a clean, damp cloth and remove stain. Use a fresh, damp towel to remove soap residue. • for grease stains, apply mopar威 multi-purpose cleaner to a clean, damp cloth and remove stain. Use a fresh, damp towel to remove soap residu...

  • Page 383

    Cleaning plastic instrument cluster lenses the lenses in front of the instruments in this vehicle are molded in clear plastic. When cleaning the lenses, care must be taken to avoid scratching the plastic. 1. Clean with a wet soft rag. A mild soap solution may be used, but do not use high alcohol con...

  • Page 384

    • after cleaning your vehicle’s fabric top, always make sure it is completely dry before lowering. • be especially careful when washing the windows by following the directions for “care of fabric top win- dows.” washing — use mopar 威 car wash or mild soap suds, lukewarm water, and a brush with soft ...

  • Page 385

    3. Always rinse thoroughly with cold water, then wipe with a soft and slightly moist, clean cloth. 4. When removing frost, snow or ice, never use a scraper or de-icing chemicals. Use warm water only if you must clean the window quickly. 5. Debris (sand, mud/dirt, dust, or salt) from off-road driving...

  • Page 386

    Cavity cartridge fuse mini fuse description j1 40 amp green power folding seat j2 30 amp pink transfer case/pwr liftgate module cavity cartridge fuse mini fuse description j3 40 amp green rear door module (rr door node) j4 25 amp natural driver door node j5 25 amp natural passenger door node j6 40 a...

  • Page 387

    Cavity cartridge fuse mini fuse description j11 30 amp pink sway bar/ thatcham lock- unlock/power slid- ing door module j13 60 amp yellow ignition off draw (iod) — main j14 40 amp green ebl (rear window defogger) j15 30 amp pink rear blower j17 40 amp green starter solenoid j18 20 amp yellow powertr...

  • Page 388

    Cavity cartridge fuse mini fuse description m6 20 amp yellow power outlet #1/rain sensor m7 20 amp yellow power outlet #2 (batt/acc select) m8 20 amp yellow front heated seat m9 20 amp yellow rear heated seat m10 20 amp yellow satellite digital audio receiver (sdars), radio, antenna (ant), vanity la...

  • Page 389

    Cavity cartridge fuse mini fuse description m15 20 amp yellow col mod, ir sns, heater ventilation, air conditioning/ automatic tempera- ture control (hvac/ atc), rear view mirror (rr vw mir), cabin compartment node (ccn), transfer case switch (t-case sw), run/st, multi- function control switch (mult...

  • Page 390

    Cavity cartridge fuse mini fuse description m20 15 amp blue cabin compartment node interior light (ccn int light), switch bank (sw bank), steering con- trol module (scm) m21 20 amp yellow auto shut down (asd #3) m22 10 amp red right horn (rt horn (hi/low) m23 10 amp red left horn (lt horn (hi/low) m...

  • Page 391

    Cavity cartridge fuse mini fuse description m29 10 amp red occupant classifica- tion module (ocm) m30 15 amp blue rear wiper module (rr wiper mod), power folding mirror (pwr fold mir) m31 20 amp yellow back-up lamps (b/u lamps) m32 10 amp red occupant restraint controller (orc), tt europe m33 10 amp...

  • Page 392

    Cavity cartridge fuse mini fuse description m37 10 amp red anti-lock brake sys- tem (abs), electronic stability program (esp), stop lamp switch (stp lp sw), fuel pump rly hi control m38 25 amp natural lock/unlock motors (lock/unlock mtrs) caution! • when installing the integrated power module cover,...

  • Page 393

    Vehicle storage if you are leaving your vehicle dormant for more than 21 days you may want to take steps to protect your battery. You may: • remove cartridge fuse #15 in the power distribution center labeled ignition-off draw (iod). • store the removed iod fuse in the power distribution center locat...

  • Page 394

    Exterior lights bulb type backup lights (2). . . . . . . . . . . . . . . . . . . . . . . . 3157 center high mounted stop light (1) . . . . . . . . . L.E.D. Fog lights. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9145 front park/turn lights (2) . . . . . . . . . . . . . . . . . 3157 front...

  • Page 395

    9. Push connector locking tab to the unlock position. 10. Remove connector from bulb. 11. Push connector onto new bulb base, and push the connector locking tab to the lock position. Caution! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb c...

  • Page 396

    Front fog light 1. Locate the front fog lamp in the front fascia, and disconnect the electrical connector from underneath. 2. Turn the bulb 1/4 turn counter-clockwise. Caution! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contac...

  • Page 397

    Center high mounted stop light (chmsl) the stop lamp is mounted on a bracket that extends upward from the tailgate behind the spare tire. If service is needed, obtain the led/cover assembly from your local authorized dealer. 1. Remove the spare tire. 2. Remove the four (4) screws holding the lens/co...

  • Page 398

    Fluids, lubricants and genuine parts engine component fluid, lubricant, or genuine part engine coolant mopar 威 antifreeze/coolant 5 year/100,000 mile formula hoat (hybrid or- ganic additive technology) engine oil api certified sae 5w-20 engine oil is recommended. Meets the requirements of daimlerchr...

  • Page 399

    Chassis component fluid, lubricant, or genuine part automatic transmission mopar 威 atf+4 automatic transmission fluid manual transmission mopar 威 manual transmission lubricant or equivalent (meeting the require- ments of daimlerchrysler material standard ms-9224) transfer case mopar 威 atf+4 automati...

  • Page 401: Maintenance Schedules

    Maintenance schedules contents 䡵 emission control system maintenance . . . . . . . . 402 䡵 maintenance schedules . . . . . . . . . . . . . . . . . . . 402 ▫ schedule “b” . . . . . . . . . . . . . . . . . . . . . . . . 405 ▫ schedule “a” . . . . . . . . . . . . . . . . . . . . . . . . 417 8 m a i n t...

  • Page 402

    Emission control system maintenance the “scheduled” maintenance services, listed in bold type must be done at the times or mileages specified to assure the continued proper functioning of the emission control system. These, and all other maintenance services included in this manual, should be done t...

  • Page 403

    • off-road or desert driving note: if any of these apply to you then change your engine oil every 3,000 miles (5 000 km) or 3 months, whichever comes first and follow “schedule b” of the “maintenance schedules” section of this manual. Note: if any of these apply to you then flush and replace your en...

  • Page 404

    Once a month • check the tire pressure and look for unusual wear or damage. • inspect the battery and clean and tighten the terminals as required. • check the fluid levels of the coolant reservoir, brake master cylinder, and transmission, and add as needed. • check all lights and all other electrica...

  • Page 405

    Schedule “b” follow this schedule if you usually operate your vehicle under one or more of the following conditions. • day or night temperatures are below 32°f (0°c) • stop and go driving • excessive engine idling • driving in dusty conditions • short trips of less than 10 miles (16.2 km) • more tha...

  • Page 406

    Miles 3,000 6,000 9,000 12,000 15,000 (kilometers) (5 000) (10 000) (14 000) (19 000) (24 000) change the engine oil and engine oil filter, if not replaced at 3 months. X x x x x rotate the tires. X x inspect the engine air filter element, replace if necessary. X inspect the brake linings. X drain a...

  • Page 407

    Miles 18,000 21,000 24,000 27,000 30,000 (kilometers) (29 000) (34 000) (39 000) (43 000) (48 000) change the engine oil and engine oil filter, if not replaced at 3 months. X x x x x rotate the tires. X x x inspect the engine air filter element, replace if necessary. X inspect the pcv valve, and rep...

  • Page 408

    Miles 33,000 36,000 39,000 42,000 45,000 (kilometers) (53 000) (58 000) (63 000) (68 000) (72 000) change the engine oil and engine oil filter, if not replaced at 3 months. X x x x x rotate the tires. X x inspect the engine air filter element, replace if necessary. X inspect the brake linings. X dra...

  • Page 409

    Miles 48,000 51,000 54,000 57,000 60,000 (kilometers) (77 000) (82 000) (87 000) (92 000) (97 000) change the engine oil and engine oil filter, if not replaced at 3 months. X x x x x rotate the tires. X x x inspect the engine air filter element, replace if necessary. X inspect the pcv valve, and rep...

  • Page 410

    Miles 63,000 66,000 69,000 72,000 75,000 (kilometers) (101 000) (106 000) (111 000) (116 000) (121 000) change the engine oil and engine oil filter, if not replaced at 3 months. X x x x x rotate the tires. X x inspect the engine air filter element, replace if necessary. X inspect the brake linings. ...

  • Page 411

    Miles 78,000 81,000 84,000 87,000 90,000 (kilometers) (126 000) (130 000) (135 000) (140 000) (145 000) change the engine oil and engine oil filter, if not replaced at 3 months. X x x x x rotate the tires. X x x inspect the engine air filter element, replace if necessary. X inspect the pcv valve, an...

  • Page 412

    Miles 93,000 96,000 99,000 102,000 105,000 (kilometers) (150 000) (154 000) (159 000) (164 000) (169 000) change the engine oil and engine oil filter, if not replaced at 3 months. X x x x x rotate the tires. X x inspect the engine air filter element, replace if necessary. X replace the spark plugs. ...

  • Page 413

    Miles 108,000 111,000 114,000 117,000 120,000 (kilometers) (174 000) (179 000) (183 000) (188 000) (193 000) change the engine oil and engine oil filter, if not replaced at 3 months. X x x x x rotate the tires. X x x inspect the engine air filter element, replace if necessary. X inspect the pcv valv...

  • Page 414

    Miles 123,000 126,000 129,000 132,000 135,000 (kilometers) (198 000) (203 000) (208 000) (212 000) (217 000) change the engine oil and engine oil filter, if not replaced at 3 months. X x x x x rotate the tires. X x inspect the engine air filter element, replace if necessary. X inspect the brake lini...

  • Page 415

    Miles 138,000 141,000 144,000 147,000 150,000 (kilometers) (222 000) (227 000) (232 000) (237 000) (241 000) change the engine oil and engine oil filter, if not replaced at 3 months. X x x x x rotate the tires. X x inspect the engine air filter element, replace if necessary. X inspect the pcv valve,...

  • Page 416

    Inspection and service should also be performed anytime a malfunction is observed or suspected. Retain all re- ceipts. † applies only if vehicle is used for frequent trailer towing or fleet/commercial service. 〫 this maintenance is recommended by the manufac- turer to the owner, but is not required ...

  • Page 417

    Schedule “a” miles 6,000 12,000 18,000 24,000 30,000 (kilometers) (10 000) (19 000) (29 000) (39 000) (48 000) [months] [6] [12] [18] [24] [30] change the engine oil and engine oil filter. X x x x x rotate the tires. X x x x x inspect the engine air filter element, and replace if necessary. X inspec...

  • Page 418

    Miles 36,000 42,000 48,000 54, 000 (kilometers) (58 000) (68 000) (77 000) (87 000) [months] [36] [42] [48] [54] change the engine oil and engine oil filter. X x x x rotate the tires. X x x x inspect the brake linings. X x clean and lubricate soft top zippers (if equipped). X x x x 418 schedule “a” ...

  • Page 419

    Miles 60,000 66,000 72,000 78,000 (kilometers) (97 000) (106 000) (116 000) (126 000) [months] [60] [66] [72] [78] change the engine oil and engine oil filter. X x x x rotate the tires. X x x x inspect the engine air filter element, and replace if nec- essary. X inspect the pcv valve, and replace if...

  • Page 420

    Miles 84,000 90,000 96,000 102, 000 (kilometers) (135 000) (145 000) (154 000) (164 000) [months] [84] [90] [96] [102] change the engine oil and engine oil filter. X x x x rotate the tires. X x x x inspect the engine air filter element, and replace if necessary. X inspect the pcv valve, and replace ...

  • Page 421

    Miles 108,000 114,000 120,000 126,000 (kilometers) (174 000) (183 000) (193 000) (203 000) [months] [108] [114] [120] [126] change the engine oil and engine oil filter. X x x x rotate the tires. X x x x inspect the engine air filter element, and replace if nec- essary. X inspect the pcv valve, and r...

  • Page 422

    Miles 132,000 138,000 144,000 150,000 (kilometers) (212 000) (222 000) (232 000) (241 000) [months] [132] [138] [144] [150] change the engine oil and engine oil filter. X x x x rotate the tires. X x x x inspect the engine air filter element, and replace if nec- essary. X inspect the pcv valve, and r...

  • Page 423

    Inspection and service should also be performed anytime a malfunction is observed or suspected. Retain all re- ceipts. 〫 this maintenance is recommended by the manufac- turer to the owner, but is not required to maintain emissions warranty. Schedule “a” 423 8 m a i n t e n a n c e s c h e d u l e s.

  • Page 425: Contents

    If you need consumer assistance contents 䡵 suggestions for obtaining service for your vehicle . . . . . . . . . . . . . . . . . . . . . . . 426 ▫ prepare for the appointment . . . . . . . . . . . . 426 ▫ prepare a list . . . . . . . . . . . . . . . . . . . . . . . . 426 ▫ be reasonable with requests...

  • Page 426

    Suggestions for obtaining service for your vehicle prepare for the appointment if you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty, discuss additional charges with the service manager. ...

  • Page 427

    Technicians, special tools, and the latest information to assure your vehicle is fixed correctly and in a timely manner. This is why you should always talk to your dealer’s service manager first. Most matters can be resolved with this process. • if for some reason you are still not satisfied, talk t...

  • Page 428

    Customer assistance for the hearing or speech impaired (tdd/tty) to assist customers who have hearing difficulties, the manufacturer has installed special tdd (telecommuni- cation devices for the deaf) equipment at its customer center. Any hearing or speech impaired customer who has access to a tdd ...

  • Page 429

    Warranty information (u.S. Vehicles only) see the warranty information booklet for the terms and provisions of daimlerchrysler’s warranties applicable to this vehicle. Mopar 姞 parts mopar 威 fluids, lubricants, parts, and accessories are available from your dealer. They will help you keep your vehicl...

  • Page 430

    Publication order forms to order the following manuals, you may use either the website or the phone numbers listed below. Visa, mas- tercard, american express, and discover orders are ac- cepted. If you prefer mailing your payment, please call for an order form. Note: a street address is required wh...

  • Page 431

    Call toll free at: • 1–800–890–4038 (u.S.) • 1–800–387–1143 (canada) or visit us on the world wide web at: • www.Techauthority.Daimlerchrysler.Com • www.Daimlerchrysler.Ca/manuals department of transportation uniform tire quality grades the following describes the tire grading categories estab- lish...

  • Page 432

    On specified government test surfaces of asphalt and concrete. A tire marked c may have poor traction perfor- mance. Warning! The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction chara...

  • Page 433: Index

    Index 10

  • Page 434

    Abs (anti-lock brake system) . . . . . . . . . . . . 192,281 adding fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . 310 adding washer fluid . . . . . . . . . . . . . . . . . . . . . 183 air cleaner, engine (engine air cleaner filter) . . . 361 air conditioner maintenance . . . . . . . . ....

  • Page 435

    Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 361 emergency starting . . . . . . . . . . . . . . . . . . . . . 342 keyless transmitter replacement (rke) . . . . . . . 25 belts, drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . 358 belts, seat . . . . . . . . . . ....

  • Page 436

    Child restraint . . . . . . . . . . . . . . . . . . . . . . 63,70,73 child restraint tether anchors . . . . . . . . . . . . . 68,70 child seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 climate control . . . . . . . . . . . . . . . . . . . . . . . . . 238 clock . . . . . . . . . ...

  • Page 437

    Dipsticks oil (engine) . . . . . . . . . . . . . . . . . . . . . . . . . . 354 disabled vehicle towing . . . . . . . . . . . . . . . . . . . 345 disarming, theft system . . . . . . . . . . . . . . . . . . . 19 disposal engine oil . . . . . . . . . . . . . . . . . . . . . . . . . . . 357 used coolant...

  • Page 438

    Exhaust gas caution . . . . . . . . . . . . . . . . . . 76,309 fails to start . . . . . . . . . . . . . . . . . . . . . . . . . . 252 flooded, starting . . . . . . . . . . . . . . . . . . . . . . 252 fuel requirements . . . . . . . . . . . . . . . . . . 306,397 jump starting . . . . . . . . . . . . ...

  • Page 439

    Power steering . . . . . . . . . . . . . . . . . . . . . . . . 363 fluids, lubricants and genuine parts . . . . . . . . . . 398 fog light service . . . . . . . . . . . . . . . . . . . . . . . . 396 fog lights . . . . . . . . . . . . . . . . . . . . . . . . . . . 98,396 fold and tumble rear seat . . ...

  • Page 440

    Gross vehicle weight rating . . . . . . . . . . . . . . . . 315 gvwr . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 313 hard top . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123 hard top, modular . . . . . . . . . . . . . . . . . . . . . . 123 hard top removal . . . . . ....

  • Page 441

    Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 jack location . . . . . . . . . . . . . . . . . . . . . . . . . . . 338 jack operation . . . . . . . . . . . . . . . . . . . . . . . 338,340 jacking instructions . . . . . . . . . . . . . . . . . . . . . . 340 jump starting . ....

  • Page 442

    Fog . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98,396 hazard warning flasher . . . . . . . . . . . . . . . . . 336 headlight switch . . . . . . . . . . . . . . . . . . . . . . . 97 headlights . . . . . . . . . . . . . . . . . . . . . . . . . . . 394 high beam . . . . . . . . . . . ....

  • Page 443

    Schedule “b” . . . . . . . . . . . . . . . . . . . . . . . . . 405 maintenance schedules . . . . . . . . . . . . . . . . . . . . 402 malfunction indicator light (check engine) . . . . . . . . . . . . . . . . . . . . . . . 195,352 manual, service . . . . . . . . . . . . . . . . . . . . . . . . . 430 ...

  • Page 444

    Oil pressure light . . . . . . . . . . . . . . . . . . . . . . . 191 onboard diagnostic system . . . . . . . . . . . . . . 351,352 outside rearview mirrors . . . . . . . . . . . . . . . . . . 84 overheating, engine . . . . . . . . . . . . . . . . . . . . . . 337 owner’s manual (operator manual) . . ...

  • Page 445

    Recreational towing . . . . . . . . . . . . . . . . . . . . . . 332 shifting into transfer case neutral (n) . . . . . . . 332 shifting out of transfer case neutral (n) . . . . . 333 reformulated gasoline . . . . . . . . . . . . . . . . . . . . 307 refrigerant . . . . . . . . . . . . . . . . . . . . ...

  • Page 446

    Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . 85 cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . 381 easy entry . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87 fold and tumble rear . . . . . . . . . . . . . . . . . . . 88 head restraints . . . . . . . ....

  • Page 447

    Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 251 automatic transmission . . . . . . . . . . . . . . . . . 251 cold weather . . . . . . . . . . . . . . . . . . . . . . . . . 252 engine block heater . . . . . . . . . . . . . . . . . . . . 254 engine fails to start . . . . . ....

  • Page 448

    High speed . . . . . . . . . . . . . . . . . . . . . . . . . . 296 inflation pressures . . . . . . . . . . . . . . . . . . . . . 294 jacking . . . . . . . . . . . . . . . . . . . . . . . . . . . 338,340 load capacity . . . . . . . . . . . . . . . . . . . . . 289,290 pressure monitor system (tpms) . ...

  • Page 449

    Transmission automatic . . . . . . . . . . . . . . . . . . . . . . . . . . . 261 maintenance . . . . . . . . . . . . . . . . . . . . . . . 374,376 manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 255 range indicator . . . . . . . . . . . . . . . . . . . . . . . 194 shifting . . . . ....

  • Page 450

    Wind buffeting . . . . . . . . . . . . . . . . . . . . . . . . . . 34 window fogging . . . . . . . . . . . . . . . . . . . . . . . . 244 windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 windshield, folding ....

  • Page 451: Notes

    Notes.

  • Page 452: Notes

    Notes.

  • Page 453: Notes

    Notes.

  • Page 454: Notes

    Notes.

  • Page 455: Notes

    Notes.

  • Page 456: Notes

    Notes.