1. DL manuals
  2. Jeep
  3. Automobile
  4. 2007 Patriot
  5. Owner's Manual

Jeep 2007 Patriot Owner's Manual

Other manuals for 2007 Patriot: Maintenance Service Manual
Manual is about: Jeep 2007 Patriot

Summary of 2007 Patriot

  • Page 1

    2007 owner’ s manual 2 0 0 7 p a t r io t 81-326-0712 first edition printed in u.S.A..

  • Page 2: Table Of Contents

    Table of contents section page 1 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 things to know before starting your vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 3 understanding the fe...

  • Page 4: Introduction

    Introduction contents m introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 ▫ roll over warning . . . . . . . . . . . . . . . . . . . . . 4 m how to use this manual . . . . . . . . . . . . . . . . . . 5 m warnings and cautions . . . . . . . . . . . . . . . . . . . 7 m vehicle identi...

  • Page 5

    Introduction this manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your new vehicle. It is supplemented by a warranty information booklet and various customer oriented documents. You are urged to read these publ...

  • Page 6

    Failure to use driver and passenger seat belts provided is a major cause of severe or fatal injury. In fact, the u.S. Government notes that the universal use of existing seat belts could cut the highway death toll by 10,000 or more each year, and could reduce disabling injuries by 2 million annually...

  • Page 7

    6 introduction.

  • Page 8

    Warnings and cautions this manual contains warnings against operating procedures, which could result in an accident or bodily injury. It also contains cautions against procedures, which could result in damage to your vehicle. If you do not read this entire manual, you may miss important information....

  • Page 9

    Vehicle modifications/alterations warning! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death. 8 introduction.

  • Page 10: Contents

    Things to know before starting your vehicle contents m a word about your keys . . . . . . . . . . . . . . . . . .12 ▫ ignition key removal . . . . . . . . . . . . . . . . . . .12 ▫ locking doors with the key . . . . . . . . . . . . . .13 ▫ key-in-ignition reminder . . . . . . . . . . . . . . . .14 m...

  • Page 11

    ▫ “child-protection” door lock system (rear doors) — if equipped . . . . . . . . . . . . . . . . . . . . . . . .23 m remote keyless entry — if equipped . . . . . . . . .24 ▫ to unlock the doors and liftgate . . . . . . . . . .25 ▫ to lock the doors and liftgate . . . . . . . . . . . .26 ▫ using the ...

  • Page 12

    ▫ seat belt extender . . . . . . . . . . . . . . . . . . . . . .48 ▫ seat belts and pregnant women . . . . . . . . . . . .49 ▫ driver and front passenger supplemental restraint system (srs) - airbag . . . . . . . . . . . .49 ▫ event data recorder (edr) . . . . . . . . . . . . . . .58 ▫ child restrai...

  • Page 13

    A word about your keys the dealer that sold you your new vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys from your dealer. Ask your dealer for these numbers and keep them in a safe place. Ignition key removal automatic transaxle place the sh...

  • Page 14

    Note: if you try to remove the key before you place the lever in park, the key may become trapped temporarily in the ignition cylinder. If this occurs, rotate the key to the right slightly, then remove the key as described. If a malfunction occurs, the system will trap the key in the ignition cylind...

  • Page 15

    Key-in-ignition reminder opening the driver’s door when the key is in the ignition, sounds a signal to remind you to remove the key. Note: with the driver’s door open, and the key in the ignition, both the power door locks and remote keyless entry (rke) will not function. Sentry key — if equipped th...

  • Page 16

    Note: • the sentry key immobilizer system is not compatible with remote starting systems. Use of these systems may result in vehicle starting problems and loss of security protection. • exxon/mobil speed pass,™ additional sentry keys, or any other transponder equipped components on the same keychain...

  • Page 17

    Sentry key programming you can program new keys to the system if you have two valid sentry keys by performing the following procedure: 1. Cut the additional sentry key transponder blank(s) to match the ignition switch lock cylinder key code. 2. Insert the first valid key into the ignition switch and...

  • Page 18

    Steering wheel lock — manual transmission only your manual transmission vehicle is equipped with a passive steering wheel lock. This lock prevents steering the vehicle without the ignition key. If the steering wheel is moved no more than 1/2 turn in either direction and the key is not in the ignitio...

  • Page 19

    Door locks manual door locks use the manual door lock plunger to lock the doors from inside the vehicle. If the plunger is down when the door is closed, the door will lock. Therefore, make sure the keys are not inside the vehicle before closing the door. Warning! For personal security, and safety in...

  • Page 20

    Caution! An unlocked vehicle is an invitation to thieves. Always remove the key from the ignition and lock all of the doors when leaving the vehicle unattended. Power door locks a door lock switch is located on the driver door panel. Press this switch to lock or unlock the doors. Power door lock swi...

  • Page 21

    Automatic door locks—if equipped the doors will lock automatically on vehicles with power door locks if all of the following conditions are met: 1. The auto lock feature is enabled. 2. The transmission is in gear. 3. All doors are closed. 4. The throttle is pressed. 5. The vehicle speed is above 15 ...

  • Page 22

    3. Depress the power door lock switch to lock the doors. 4. Verify reprogramming by driving the vehicle. Auto unlock the doors will unlock automatically on vehicles with power door locks if: 1. The auto unlock feature is enabled. 2. The transmission was in gear and the vehicle speed returned to 0 mp...

  • Page 23

    The auto unlock feature can be enabled or disabled. Refer to “personal settings” (customer programmable features) in the electronic vehicle information center (evic) — if equipped section of this manual. For vehicles not equipped with the evic the auto unlock feature can be enabled or disabled by pe...

  • Page 24

    Note: use the auto door locks and auto unlock features in accordance with local laws. “child-protection” door lock system (rear doors) — if equipped insert the tip of the ignition key into the lock and rotate to the lock or unlock position. Child protection door lock location inserting ignition key ...

  • Page 25

    Warning! Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child protection locks are engaged. Note: for emergency exit with the system engaged, move the lock plunger up (unlocked position), roll down window and open the door...

  • Page 26

    Note: the line of transmission must not be blocked with metal objects. To unlock the doors and liftgate: press and release the unlock button on the key fob once to unlock only the driver’s door or twice to unlock all the doors and liftgate. When the unlock button is pressed, the illuminated entry wi...

  • Page 27

    Note: pressing the lock button on the keyfob while you are inside the vehicle will activate the security alarm. Opening a door with the security alarm activated will cause the alarm to sound. Press the unlock button to deactivate the security alarm. 5. If the desired programming was not achieved or ...

  • Page 28

    Note: when you turn off the panic alarm by pressing the panic button a second time, you may have to be closer to the vehicle due to the radio frequency noises of the system. To turn off “flash lights with lock” note: the flash lights with lock feature can be turned on or off. On electronic vehicle i...

  • Page 29

    Use the following procedure to program additional key fobs if the vehicle is not equipped with sentry key: 1. Enter your vehicle and close all doors. 2. Fasten your seat belt (fastening the seatbelt will cancel any chiming that may confuse you during this program- ming procedure). 3. Place the key i...

  • Page 30

    Note: if you do not have a programmed transmitter, contact your dealer for details. General information this device complies with part 15 of fcc rules and with rs-210 of industry canada. Operation is subject to the following conditions: 1. This device may not cause harmful interference. 2. This devi...

  • Page 31

    1. If the key fob is equipped with a screw, remove the screw. With the transmitter buttons facing down, use a flat blade to pry the two halves of the transmitter apart. Make sure not to damage the elastomer seal during removal. 2. Remove and replace the batteries. Avoid touching the new batteries wi...

  • Page 32

    If the monitored system, which triggered the alarm is deactivated the alarm will continue to sound until 3 minutes of alarm time is reached. If the monitored system, which triggered the alarm is deactivated after the alarm has been on for 3 minutes the alarm will shut off immediately. To set the ala...

  • Page 33

    Security system manual override the system will not arm if you lock the doors using the manual door lock plunger. Liftgate note: the key that is used to start the vehicle is also used to lock or unlock the doors and open the liftgate. To unlock the liftgate, insert the key into the lock and turn to ...

  • Page 34

    Note: in the event of a power malfunction, or the remote transmitter is inoperative, insert the key into the liftgate lock cylinder and turn to the right (manual lock models only). Using the liftgate handle, pull the liftgate open with one fluid motion. Note: although the liftgate has no inside rele...

  • Page 35

    Gas props support the liftgate in the open position. However, because the gas pressure drops with tempera- ture, it may be necessary to assist the props when opening the liftgate in cold weather. Power windows power window switches power window switch location 34 things to know before starting your ...

  • Page 36

    The control on the left front door has up-down switches that give you finger tip control of all four power win- dows. There is a single opening and closing switch on the passenger doors for passenger window control. The windows will operate only when the ignition switch is turned to the on position ...

  • Page 37

    Window lockout switch the window lockout switch on the driver’s door allows you to disable the window control on the other doors. To disable the window controls on the other doors, press the window lock button. To enable the window controls, press the window control button again. Occupant restraints...

  • Page 38

    Warning! In a collision, you and your passengers can suffer much greater injuries if you are not properly buckled up. You can strike the interior of your vehicle or other passengers, or you can be thrown out of the vehicle. Always be sure you and others in your vehicle are buckled up properly. Buckl...

  • Page 39

    Warning! • it is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seri- ously injured or killed. • do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • ...

  • Page 40

    Lap/shoulder belt operating instructions 1. Enter the vehicle and close the door. Sit back and adjust the seat. 2. The seat belt latch plate is above the back of the front seat, next to your arm. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to...

  • Page 41

    3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” warning! • a belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your bel...

  • Page 42

    4. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision. War...

  • Page 43

    6. To release the belt, push the red button on the buckle. The belt will automatically retract to its stowed position. If necessary, slide the latch plate down the webbing to allow the belt to retract fully. Warning! A frayed or torn belt could rip apart in a collision and leave you with no protecti...

  • Page 44

    As a guide, if you are shorter than average, you will prefer a lower position, and if you are taller than average, you’ll prefer a higher position. When you release the anchorage, try to move it up or down to make sure that it is locked in position. Second row center lap/shoulder belt operating inst...

  • Page 45

    3. Route the shoulder belt to the inside of the right head restraint. 4. When the belt is long enough to fit, insert the mini latch plate into the mini buckle until you hear a “click.” 5. Sit back in seat. Slide the regular latch plate up the webbing as far as necessary to allow the belt to go aroun...

  • Page 46

    6. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” 7. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt if it is too tight, pull on the lap ...

  • Page 47

    9. To release the belt, push the red button on the buckle. 10. To disengage the mini latch from the mini buckle for storage, insert the regular latch plate into the black button on the top of the mini buckle. The belt will automatically retract to its stowed position. If necessary, slide the latch p...

  • Page 48

    Items. After a collision that is severe enough to deploy the airbags and pretensioners, both must be replaced. Enhanced driver seat belt reminder system (beltalert) if the driver’s seat belt has not been buckled within 60 seconds of starting the vehicle and if the vehicle speed is greater than 5 mph...

  • Page 49

    Note: watch for the seat belt warning light to turn on while unbuckling and off while re-buckling the seat belt. It may be necessary to retract the seat belt. 4. Turn the ignition switch to the lock position. A single chime will sound to signify that you have success- fully completed the programming...

  • Page 50

    Seat belts and pregnant women we recommend that pregnant women use the seat belts throughout their pregnancy. Keeping the mother safe is the best way to keep the baby safe. Pregnant women should wear the lap part of the belt across the thighs and as snug across the hips as possible. Keep the belt lo...

  • Page 51

    Note: the front airbags are certified to the federal regulations that allow less forceful deployment. The front airbags have a multistage inflator design. This may allow the airbag to have different rates of inflation that are based on collision severity. This vehicle may also be equipped with side ...

  • Page 52

    Warning! • do not put anything on or around the front airbag covers or attempt to manually open them. You may damage the airbags and you could be injured because the airbags are no longer functional. These protective covers for the airbag cushions are designed to open only when the airbags are infla...

  • Page 53

    Here are some simple steps you can take to minimize the risk of harm from a deploying airbag. 1. Children 12 years old and under should ride buckled up in the rear seat. 2. Infants in rear-facing child restraints should never ride in the front seat of a vehicle with a passenger front airbag. An airb...

  • Page 54

    Warning! • relying on the airbags alone could lead to more severe injuries in a collision. The airbags work with your seat belt to restrain you properly. In some collisions, the airbags won’t deploy at all. Always wear your seat belts even though you have airbags. • being too close to the steering w...

  • Page 55

    • front acceleration sensors • driver and front passenger seat belt pretensioners how the airbag system works • the occupant restraint controller (orc) determines if a frontal collision is severe enough to require the airbags to inflate. The front airbag inflators are de- signed to provide different...

  • Page 56

    • the driver and front passenger airbag/inflator units are located in the center of the steering wheel and the passenger side of the instrument panel. When the orc detects a collision requiring the airbags, it signals the inflator units. A large quantity of nontoxic gas is generated to inflate the f...

  • Page 57

    If a deployment occurs the airbag system is designed to deploy when the orc detects a moderate-to-severe collision, to help restrain the driver and front passenger, and then to immediately deflate. Note: a frontal collision that is not severe enough to need airbag protection will not activate the sy...

  • Page 58

    Warning! Deployed airbags can’t protect you in another colli- sion. Have the airbags replaced by an authorized dealer as soon as possible. Enhanced accident response system in the event of an impact that causes airbag deployment, with the vehicle stopped, and the vehicle communication network intact...

  • Page 59

    Airbag warning light you will want to have the airbags ready to inflate for your protection in an impact. While the airbag system is designed to be mainte- nance free, if any of the following occurs, have an authorized dealer service the system promptly: • the airbag warning light does not come on o...

  • Page 60

    In conjunction with other data gathered during a com- plete accident investigation, the electronic data may be used by daimlerchrysler and others to learn more about the possible causes of crashes and associated injuries in order to assess and improve vehicle performance. In addition to crash invest...

  • Page 61

    Data parameters that may be recorded: • diagnostic trouble code(s) and warning lamp status for electronically-controlled safety systems, including the airbag system • airbag disable lamp status (if equipped) • 9time9 of airbag deployment (in terms of ignition cycles and vehicle mileage) • airbag dep...

  • Page 62

    Warning! In a collision, an unrestrained child, even a tiny baby, can become a missile inside the vehicle. The force required to hold even an infant on your lap could become so great that you could not hold the child, no matter how strong you are. The child and others could be badly injured. Any chi...

  • Page 63

    • rearward-facing child seats must never be used in the front seat of a vehicle with a front passenger airbag. An airbag deployment could cause severe injury or death to infants in this position. • children who weigh more than 20 lbs (9 kg) and who are older than one year can ride forward-facing in ...

  • Page 64

    Here are some tips on getting the most out of your child restraint: • before buying any restraint system, make sure that it has a label certifying that it meets all applicable safety standards. We also recommend that you make sure that you can install the child restraint in the vehicle where you wil...

  • Page 65

    • if the belt still can’t be tightened, or if by pulling and pushing on the restraint loosens the belt, disconnect the latch plate from the buckle, turn the latch plate around, and insert the latch plate into the buckle again. If you still can’t make the child restraint secure, try a different seati...

  • Page 66

    Fixed lower attachments must be installed in the out- board positions only. Regardless of the specific type of lower attachment, never install latch-compatible child seats such that two seats share a common lower anchorage. If you are installing latch-compatible child restraints in adjacent rear sea...

  • Page 67

    Provide add-on tether strap kits for some of their older products. Tether anchorage kits are also available for most older vehicles. Because the lower anchorages are to be introduced to passenger carrying vehicles over a period of years, child restraint systems having attachments for those anchor- a...

  • Page 68

    In general, you will first loosen the adjusters on the lower and tether straps so that you can more easily attach the hook or connector to the lower and tether anchorages. The tether strap should be routed under the center of the head restraint and attached to the tether anchor on the rear of the se...

  • Page 69

    Warning! An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchor position directly behind the child seat to secure a child restraint top tether strap. Children too large for booster seats children who are large enough to wear the...

  • Page 70

    Engine break-in recommendations a long break-in period is not required for the engine in your new vehicle. Drive moderately during the first 300 miles (500 km). After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable. While cruising, brief full-throttle accelerat...

  • Page 71

    Do not run the engine in a closed garage or in confined areas any longer than needed to move your vehicle in or out of the area. If it is necessary to sit in a parked vehicle with the engine running, adjust your heating or cooling controls to force outside air into the vehicle. Set the blower at hig...

  • Page 72

    Defroster check operation by selecting the defrost mode and place the blower control on high speed. You should be able to feel the air directed against the windshield. Periodic safety checks you should make outside the vehicle tires examine tires for excessive tread wear or uneven wear patterns. Che...

  • Page 74: Contents

    Understanding the features of your vehicle contents m mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78 ▫ inside day/night mirror — if equipped . . . . . .78 ▫ outside mirror—driver’s side . . . . . . . . . . . . .78 ▫ outside mirror—passenger’s side . . . . . . . . . . .79 ▫ f...

  • Page 75

    ▫ front seat adjustment . . . . . . . . . . . . . . . . . . 108 ▫ manual seat height adjustment — if equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . 109 ▫ manual lumbar— if equipped . . . . . . . . . . . . 109 ▫ driver’s seat back recline . . . . . . . . . . . . . . . 110 ▫ adjustable...

  • Page 76

    ▫ windshield wiper operation . . . . . . . . . . . . . 125 ▫ intermittent wiper system . . . . . . . . . . . . . . . 125 ▫ adding washer fluid . . . . . . . . . . . . . . . . . . 126 m tilt steering column . . . . . . . . . . . . . . . . . . . . 126 m electronic speed control — if equipped . . . . ....

  • Page 77

    ▫ hill descent control (hdc) – if equipped . . . 140 ▫ esp (electronic stability program) . . . . . . . . . 141 m power sunroof — if equipped . . . . . . . . . . . . . 146 ▫ opening sunroof – manual . . . . . . . . . . . . . . 147 ▫ opening sunroof – express mode . . . . . . . . . . 147 ▫ closing su...

  • Page 78

    ▫ rear window defroster . . . . . . . . . . . . . . . . . 159 m roof luggage rack — if equipped . . . . . . . . . . 160 understanding the features of your vehicle 77 3.

  • Page 79

    Mirrors inside day/night mirror — if equipped adjust the mirror to center on the view through the rear window. A two point pivot system allows for horizontal and vertical mirror adjustment. Annoying headlight glare can be reduced by moving the small control under the mirror to the night position (to...

  • Page 80

    Outside mirror—passenger’s side adjust the convex ( passenger’s side) outside mirror to center on the adjacent lane of traffic with a slight overlap of the view obtained on the inside mirror. Warning! Vehicles and other objects seen in the passenger side convex mirror will look smaller and farther a...

  • Page 81

    Folding outside mirrors — if equipped the exterior mirrors are hinged and may be moved, manually, either forward or rearward to resist damage. The hinges have three detent positions; full forward, full rearward, and normal. Electric remote-control mirrors the controls for the power mirrors are locat...

  • Page 82

    To adjust a mirror, turn the control wand toward the left or right mirror positions indicated. Tilt the control wand in the direction you want the mirror to move. When finished adjusting the mirror, turn the control to the center position to prevent accidentally moving a mirror. Warning! Vehicles an...

  • Page 83

    Vanity mirrors — if equipped to use the mirror, rotate the sun visor down and swing the mirror cover upward. Sun visor sliding feature the sun visors may be pulled out to provide extended coverage of the side glass. Hands–free communication (uconnect™) — if equipped uconnect™ is a voice-activated, h...

  • Page 84

    Uconnect™ allows you to transfer calls between the system and your cellular phone as you enter or exit your vehicle, and enables you to mute the system’s micro- phone for private conversation. The uconnect™ phonebook enables you to store up to 32 names and four numbers per name. Each language has a ...

  • Page 85

    The uconnect™ system can be used with any hands- free profile certified bluetooth™ cellular phone. See www.Chrysler.Com/uconnect for supported phones. If your cellular phone supports a different profile (e.G., headset profile), you may not be able to use any ucon- nect™ features. Refer to your cellu...

  • Page 86

    Example, you can use the combined form voice com- mand 9phonebook new entry,9 or you can break the combined form command into two voice commands: 9phonebook9 and 9new entry.9 please remember, the uconnect™ system works best when you talk in a normal conversational tone, as if speaking to some one si...

  • Page 87

    Note: • www.Chrysler.Com/uconnect • www.Dodge.Com/uconnect • www.Jeep.Com/uconnect the following are general phone to uconnect™ system pairing instructions: • press the ’phone’ button to begin. • after the 9ready9 prompt and the following beep, say 9setup phone pairing9 and follow the audible prompt...

  • Page 88

    Call/dial by saying a number • press the ’phone’ button to begin. • after the 9ready9 prompt and the following beep, say 9dial.9 • system will prompt you to say the number you want call. • for example, you can say “234-567-8901.” the phone number that you enter must be of valid length and combinatio...

  • Page 89

    Add names to your uconnect™ phonebook note: adding names to phonebook is recommended when vehicle is not in motion. • press the “phone” button to begin. • after the 9ready9 prompt and the following beep, say 9phonebook new entry.9 • when prompted, say the name of the new entry. Use of long names hel...

  • Page 90

    • you will then be asked for the name of the phonebook entry that you wish to edit. • next, choose the number designation (home, work, mobile, or pager) that you wish to edit. • when prompted, recite the new phone number for the phonebook entry that you are editing. After you are finished editing an...

  • Page 91

    • after you enter the name, the uconnect™ system will ask you which designation you wish to delete, home, work, mobile, or pager. Say the designation you wish to delete. • note that only the phonebook entry in the current language is deleted. After confirmation, the phonebook entries will be de- let...

  • Page 92

    Phone call features the following features can be accessed through the uconnect™ system if the feature(s) are available on your cellular service plan. For example, if your cellular service plan provides three-way calling, this feature can be accessed through the uconnect™ system. Check with your cel...

  • Page 93

    Second call is in progress. To go back to the first call, refer to 9toggling between calls.9 to combine two calls, refer to 9conference call.9 place/retrieve a call from hold to put a call on hold, press the 8phone’ button until you hear a single beep. This indicates that the call is on hold. To bri...

  • Page 94

    Hold may not become active automatically. This is cell phone dependent. To bring the call back from hold, press and hold the ‘phone’ button until you hear a single beep. Redial • press the ’phone’ button to begin. • after the 9ready9 prompt and the following beep, say 9redial.9 • the uconnect™ syste...

  • Page 95

    • after the 9ready9 prompt and the following beep, say the name of the language you wish to switch to (english, espanol, or francais, if so equipped). • continue to follow the system prompts to complete language selection. After selecting one of the languages, all prompts and voice commands will be ...

  • Page 96

    Your phone must be turned on and paired to the ucon- nect™ system to allow use of this vehicle feature in emergency situations when the cell phone has network coverage and stays paired to the uconnect™ system. Towing assistance if you need towing assistance, • press the ’phone’ button to begin. • af...

  • Page 97

    When calling a number with your uconnect™ system that normally requires you to enter in a touch-tone sequence on your cellular phone keypad, you can push the ’voice recognition’ button and say the sequence you wish to enter followed by the word 9send.9 for example, if required to enter your pin numb...

  • Page 98

    Dialing using the cellular phone keypad you can dial a phone number with your cellular phone keypad and still use the uconnect™ system (while dialing via the cell phone keypad, the user must exercise caution and take precautionary safety measures). By dialing a number with your paired bluetooth™ cel...

  • Page 99

    Information service when using at&t wireless service, dialing to phone number 9#121,9 you can access voice activated automated system to receive news, weather, stocks, traffic, etc. Related information. Advanced phone connectivity transfer call to and from cellular phone the uconnect™ system allows ...

  • Page 100

    Select another cellular phone this feature allows you to select and start using another phone with the uconnect™ system. The phone must have been previously paired to the uconnect™ system that you want to use it with. • press the ’phone’ button to begin. • after the 9ready9 prompt and the following ...

  • Page 101

    Training mode, follow one of the two procedures: from outside the uconnect mode (e.G. From radio mode), • press and hold the ‘voice recognition’ button for 5 seconds until the session begins, or • press the ‘voice recognition’ button and say 9setup, voice training 9 command. Repeat the words and phr...

  • Page 102

    • in a convertible vehicle, the system performance may be compromised with roof top down. • even though the system is designed for users speaking in north american english, french, and spanish ac- cents, the system may not always work for some. • when navigating through an automated system, such as ...

  • Page 103

    • in a convertible vehicle, the system performance may be compromised with roof top down. • performance, such as audio clarity, echo, and loudness to a large degree rely on the phone and network, and not the uconnect™ system. • echo at far end can sometime be reduced by lowering the in-vehicle audio...

  • Page 104

    Understanding the features of your vehicle 103 3.

  • Page 105

    104 understanding the features of your vehicle.

  • Page 106

    Understanding the features of your vehicle 105 3.

  • Page 107

    North american english primary alternate(s) zero one two three four five six seven eight nine star (*) plus (+) pound (#) add location all call cancel confirmation prompts continue delete dial edit emergency english erase all espanol francais help home language list names list phones 106 understandi...

  • Page 108

    Mobile mute mute off new entry no pager pair a phone phone pairing pairing phonebook phone book previous record again redial return to main menu return. Main menu select phone select send set up phone settings / phone set up towing assistance transfer call try again voice training work yes general i...

  • Page 109

    Seats front seat adjustment the adjusting bar is at the front of the seats, near the floor. Pull the bar up to move the seat to the desired position. Using body pressure, move forward and rearward on the seat to be sure the seat adjusters have latched. Warning! • adjusting a seat while the vehicle i...

  • Page 110

    Manual seat height adjustment — if equipped the driver’s seat height can be raised or lowered by using the ratcheting handle on the outboard side of the seat to adjust the driving position. Manual lumbar— if equipped the lumbar adjustment is located on the outboard side of the driver’s seat. To incr...

  • Page 111

    Driver’s seat back recline to recline: 1. Lean forward before lifting the handle, then lean back to the desired position and release the handle. 2. Lift the handle to return the seatback to an upright position. Adjustable head restraints head restraints can reduce the risk of whiplash injury in the ...

  • Page 112

    Heated seats — if equipped warning! Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaus- tion or other physical condition must exercise care when using the seat heater. It may cause burns even at low ...

  • Page 113

    This feature heats the front driver’s and passenger’s seats. The controls for the heater is located on the instrument panel, below the radio. After turning on the ignition, you may choose off, high, or low heat settings. An indicator on the switch shows which setting has been chosen. • pressing the ...

  • Page 114

    Fold flat front passenger seat fold flat front passenger seat control front passenger seat folded flat understanding the features of your vehicle 113 3.

  • Page 115

    Folding rear seat to provide additional storage area, each rear seatback can be folded forward. Pull the strap forward to move the seat forward and flat. Folding rear seat rear seat folded flat 114 understanding the features of your vehicle.

  • Page 116

    Reclining rear seat — if equipped rear seat recline pull reclining the rear seat understanding the features of your vehicle 115 3.

  • Page 117

    For additional comfort, pull the strap forward just enough to release the seatback latch. Then push the seatback to a reclined position, approximately 35 degrees maximum, and release the strap. Warning! • it is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collisi...

  • Page 118

    Then move the safety catch located under the front edge of the hood, near the center and raise the hood. Lift the hood prop rod, clipped to the right side (left side facing hood) of the engine compartment, to secure the hood in the open position. Place the hood prop at the location stamped into the ...

  • Page 119

    Lights map/reading lights these lights are mounted between the sun visors above the rear view mirror. Each light is turned on by pressing the button. Press the button a second time to turn the light off. The lights also come on when a door is opened or the dimmer control is turned fully upward, past...

  • Page 120

    Multi-function control lever the multi-function control lever controls the operation of the headlights, parking lights, turn signals, headlight beam selection, instrument panel light dimming, interior lights, the passing lights, and fog lights. The lever is located on the left side of the steering c...

  • Page 121

    To change the brightness of the instrument panel lights, rotate the center portion of the multi-function control lever up or down. Lights-on reminder if the headlights or parking lights are on after the ignition is turned off, a chime will sound to alert the driver when the driver’s door is opened. ...

  • Page 122

    Fog lights — if equipped the front fog light switch is on the multi-function control lever. To activate the front fog lights, turn on the parking lights or the low beam headlights and pull out the end of the control lever. Note: the fog lights will only operate with the head- lights on low beam. Sel...

  • Page 123

    Show proper operation of the front and rear turn signal lights. You can signal a lane change by moving the lever partially up or down without moving beyond the detent. If either light remains on and does not flash, or there is a very fast flash rate, check for a defective outside light bulb. If an i...

  • Page 124

    Passing light you can signal another vehicle with your headlights by lightly pulling the multi-function control lever toward you. This will cause the headlights to turn on at high beam and remain on until the lever is released. Note: if the multi-function control lever is held in the flash to pass p...

  • Page 125

    If the lever is pulled while in the off position, the wipers will operate for two wipe cycles, then turn off. Mist feature push down on the wiper control lever to activate a single wipe to clear the windshield of road mist or spray from a passing vehicle. As long as the lever is held down, the wiper...

  • Page 126

    Caution! In cold weather, always turn off the wiper switch and allow the wipers to return to the park position before turning off the engine. If the wiper switch is left on and the wipers freeze to the windshield, damage to the wiper motor may occur when the vehicle is restarted. Windshield wiper op...

  • Page 127

    (counterclockwise) to increase the delay time. The delay can be regulated from a maximum of approximately 18 seconds between cycles, to a cycle every second. Adding washer fluid the fluid reservoir for the windshield washers and the rear window washer (if equipped) is shared. It is located in the fr...

  • Page 128

    Warning! Tilting the steering column while the vehicle is moving is dangerous. Without a stable steering col- umn, you could lose control of the vehicle and have an accident. Adjust the column only while the ve- hicle is stopped. Be sure it is locked before driving. Electronic speed control — if equ...

  • Page 129

    Warning! Leaving the electronic speed control system on when not in use is dangerous. You could accidentally set the system or cause it to go faster than you want. You could lose control and have an accident. Always leave the system off when you are not using it. To set at a desired speed: when the ...

  • Page 130

    Tapping “resume accel” once will result in a 1 mph (1.6 km/h) speed increase. Each time the lever is tapped, speed increases so that tapping the lever three times will increase speed by 3 mph (4.8 km/h), etc. To decrease speed while speed control is on, push down and hold “set decel”. Release the le...

  • Page 131

    On steep hills a greater speed loss or gain may occur so it may be preferable to drive without speed control. Garage door opener — if equipped note: the homelink t system will be disabled if the vehicle theft alarm (if equipped) is in the armed or alarming state. The homelink t system will only oper...

  • Page 132

    Warning! A moving garage door can cause injury to people and pets in the path of the door. People or pets could be seriously or fatally injured. Only use this transceiver with a garage door opener that has a “stop and reverse” feature as required by federal safety stan- dards. This includes most gar...

  • Page 133

    Warning! Your motorized door or gate will open and close while you are training the universal transceiver. Do not train the transceiver if people or pets are in the path of the door or gate. A moving door or gate can cause serious injury or death to people and pets or damage to objects. 2. Erase the...

  • Page 134

    4. Using both hands, press the hand held transmitter button and the desired universal transceiver button. Do not release the buttons until step 5 has been completed. Note: some entry gates and garage door openers may require you to replace step 4 with the procedures listed under canadian programming...

  • Page 135

    • press and hold the programmed button on the univer- sal transceiver. If the universal transceiver indicator light flashes rapidly and then stays on after 2 seconds, the device has the “rolling code” feature. To train a garage door opener (or other rolling code equipped devices) with the rolling co...

  • Page 136

    Canadian programming/gate programming canadian frequency laws, and the technology of some entry gates, require you to press and release the hand held transmitter button every two seconds during pro- gramming. Continue to press and hold the universal transceiver button while you press and release the...

  • Page 137

    Security if you sell your vehicle, be sure to erase the frequencies. To erase all of the previously trained frequencies, hold down both outside buttons until the indicator light begins to flash. This device complies with part 15 of fcc rules and with rs-210 of industry canada. Operation is subject t...

  • Page 138

    Warning! • anti-lock system (abs) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency beyond that afforded by the condition of the vehicle brakes and tires or the traction afforded. • the abs cannot prevent accidents, including th...

  • Page 139

    Traction control system (tcs) this system monitors the amount of wheel spin of each of the driven wheels. If wheel spin is detected, brake pressure is applied to the slipping wheel(s) and engine power is reduced to provide enhanced acceleration and stability. A feature of the tcs system functions si...

  • Page 140

    Warning! • bas cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase braking efficiency beyond that afforded by the condition of the vehicle brakes and tires or the traction afforded. • the bas cannot prevent accidents, including those resulting from excessive sp...

  • Page 141

    Warning! Many factors, such as vehicle loading, road condi- tions and driving conditions, influence the chance that wheel lift or rollover may occur. Erm can not prevent all wheel lift or rollovers, especially those that involve leaving the roadway or striking objects or other vehicles. Only a safe,...

  • Page 142

    The accelerator pedal will increase vehicle speed like normal. When either the brake or the accelerator is released, hdc will control the vehicle back to the origi- nal set speed. Hdc is only intended for low speed off-road driving. At vehicle speeds above 31 mph (50 km/h) hdc will no longer functio...

  • Page 143

    Warning! • electronic stability program (esp) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions. • esp cannot prevent accidents, including those resulting from excessive speed in turns, driving on very slipp...

  • Page 144

    Gravel conditions and more wheel spin than esp would normally allow is required to gain traction. To turn esp on again, momentarily depress the “esp control switch”. This will restore the normal “esp on” mode of operation. Warning! In the partial esp mode, the engine torque reduction and stability f...

  • Page 145

    In this mode, esp and tcs, except for the “limited slip” feature described in the tcs section, are turned off until the vehicle reaches a speed of 35 mph (56 km/h). At 35 mph (56 km/h) the normal esp stability function returns with the exception of engine power reduction. Tcs remains off. When the v...

  • Page 146

    Warning! With the esp switched off, the enhanced vehicle stability offered by esp is unavailable. In an emer- gency evasive maneuver, the esp system will not engage to assist in maintaining stability. “esp off” mode is intended for off-highway or off-road use, only. Note: • the “esp indicator light”...

  • Page 147

    Power sunroof — if equipped the power sunroof switch is located in the reading lamp. Warning! • never leave children in a vehicle, with the keys in the ignition switch. Occupants, particularly unat- tended children, can become entrapped by the power sunroof while operating the power sunroof switch. ...

  • Page 148

    Opening sunroof – manual to open the sunroof, press and hold the switch rearward to full open. Any release of the switch will stop the movement and the sunroof will remain in a partial open condition until the switch is pushed and held rearward again. Opening sunroof – express mode by pressing the s...

  • Page 149

    Pinch protect override if a known obstruction (ice, debris, etc.) prevents closing, press the switch forward and hold for two seconds after the reversal occurs. This allows the sunroof to move towards the close position. Note: pinch protection is disabled while the switch is pressed. Venting sunroof...

  • Page 150

    Sunroof maintenance use only a non-abrasive cleaner and a soft cloth to clean the glass panel. Ignition off operation the sunroof will also operate up to 45 seconds after the ignition has been turned off. The sunroof operation will be canceled if either of the front doors are opened during the acces...

  • Page 151

    Power outlet 12 volts power outlet 115 volts (150 watt) 150 understanding the features of your vehicle.

  • Page 152

    Electrical outlet use with engine off caution! • many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.E. Cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or p...

  • Page 153

    The floor console’s sliding armrest moves forward 3 inches to accommodate shorter drivers. The armrest lid also includes a unique flip pocket for storing a phone or an mp3 player. The bin inside the console can hold up to 10 cd jewel cases or other items securely out of sight. Note: the flip pocket ...

  • Page 154

    To operate the flashlight, press the switch once for high, twice for low, and a third time to return to off. Press and release removing flashlight understanding the features of your vehicle 153 3.

  • Page 155

    Retractable cargo area cover — if equipped to cover the cargo area: 1. Grasp the center portion of the cover flap. Pull it over the cargo area. 2. Insert the pins on the ends of the cover into the slots in the pillar trim cover. 3. The liftgate may be opened or closed with the cargo cover in place. ...

  • Page 156

    Cargo cover removal warning! In an accident a cargo cover loose in the vehicle could cause injury. It could fly around in a sudden stop and strike someone in the vehicle. Do not store the cargo cover on the cargo floor or in the passenger compart- ment. Remove the cover from the vehicle when taken f...

  • Page 157

    Removable load floor the cargo area load floor is removable and can be washed with mild soap and water. For removal, lift the load floor with your finger at the space provided at the rear. Cargo tie-down loops there are four d-rings tie-down loops in the lower trim for securing cargo. The tie-downs ...

  • Page 158

    • always place cargo evenly on the cargo floor. Put heavier objects as low and as far forward as possible. • place as much cargo as possible in front of the rear axle. Too much weight or improperly placed weight over or behind the rear axle can cause the rear of the vehicle to sway. • do not pile lu...

  • Page 159

    Rear window features rear window wiper/washer a switch on the right side of the steering column controls operation of the rear wiper/washer function. Rotating the center of the switch forward to the on position will activate the wiper. The rear wiper operates in an inter- mittent mode only. Rotating...

  • Page 160

    Adding washer fluid the fluid reservoir for the windshield washers and the rear window washer (if equipped) is shared. It is located in the front of the engine compartment on the passenger side and should be checked for fluid level at regular intervals. Fill the reservoir with windshield washer sol-...

  • Page 161

    Caution! Use care when washing the inside of the rear window to prevent damage to heating elements. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements. Also, keep all objects a safe distance from the window to prevent damaging the heating elements. Roof luggage rac...

  • Page 162

    Caution! • to prevent damage to the roof of your vehicle, do not carry any loads on the roof rack without cross rails installed. The load should be secured and placed on top of the cross rails, not directly on the roof. If it is necessary to place the load on the roof, place a blanket or some other ...

  • Page 164: Contents

    Understanding your instrument panel contents m instrument panel features . . . . . . . . . . . . . . . . . 167 m instrument cluster—premium . . . . . . . . . . . . . . 168 m instrument cluster descriptions . . . . . . . . . . . . 169 m electronic vehicle information center (evic) – if equipped . . ....

  • Page 165

    ▫ two types of signals . . . . . . . . . . . . . . . . . . 189 ▫ electrical disturbances . . . . . . . . . . . . . . . . . . 190 ▫ am reception . . . . . . . . . . . . . . . . . . . . . . . 190 ▫ fm reception . . . . . . . . . . . . . . . . . . . . . . . . 190 m electronic digital clock . . . . . . ...

  • Page 166

    M sales code rec — am/fm/cd (6–disc) radio with navigation system . . . . . . . . . . . . . . . . . . . . . . 213 ▫ operating instructions — satellite radio (if equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . 213 ▫ rec setting the clock . . . . . . . . . . . . . . . . . 213 ▫ audio clo...

  • Page 167

    ▫ air conditioning . . . . . . . . . . . . . . . . . . . . . 226 ▫ air filtration system – if equipped . . . . . . . . 228 ▫ operating tips . . . . . . . . . . . . . . . . . . . . . . . 229 166 understanding your instrument panel.

  • Page 168

    Instrument panel features 1 — air outlet 5 — glove box 9 — hazard warning flasher 2 — demisters 6 — storage bin 10 — esp off switch* 3 — instrument cluster 7 — climate control * if equipped 4 — radio 8 — heated seat switches* understanding your instrument panel 167 4.

  • Page 169

    Instrument cluster—premium 168 understanding your instrument panel.

  • Page 170

    Instrument cluster descriptions 1. Fuel gauge/fuel door location when the ignition switch is in the on position, the pointer will show the level of fuel remain- ing in the fuel tank. The fuel pump symbol points to the side of the vehicle where the fuel door is located 2. Charging system light 9this ...

  • Page 171

    4. Oil pressure light shows low engine oil pressure. The light will come on and remain on when the ignition switch is turned from the off to the on position, and the light will turn off after the engine is started. If the bulb does not come on during starting, have the system checked by an authorize...

  • Page 172

    10. Anti-lock warning light (abs) — if equipped this light monitors the anti-lock brake system (abs) described elsewhere in this manual. This light will come on when the ignition key is turned to the on position and may stay on for as long as four seconds. If the abs light remains on or comes on dur...

  • Page 173

    Will sound 10 times. After the chime turns off, the engine will still be critically hot until the light goes out. 14. Brake system warning light this light monitors various brake functions, in- cluding brake fluid level and parking brake appli- cation. If the brake light turns on, it may indicate th...

  • Page 174

    In the event of an ebd failure, the brake warning light will turn on along with the abs light. Immediate repair to the abs system is required. The operation of the brake warning light can be checked by turning the ignition switch from the off position to the on position. The light should illuminate ...

  • Page 175

    The pointer drops back into the normal range. If the pointer remains on the h (red) mark, turn the engine off immediately and call for service. There are steps that you can take to slow down an impending overheat condition. If your air conditioning is on, turn it off. The air conditioning system add...

  • Page 176

    Vehicle placard or tire inflation pressure label, you should determine the proper tire inflation pressure for those tires.) as an added safety feature, your vehicle has been equipped with a tire pressure monitoring system (tpms) that illuminates a low tire pressure telltale when one or more of your ...

  • Page 177

    Caution! The tpms has been optimized for the original equipment tires and wheels. Tpms pressures and warning have been established for the tire size equipped on your vehicle. Undesirable system opera- tion or sensor damage may result when using re- placement equipment that is not of the same size, t...

  • Page 178

    25. Off road light — if equipped the symbol illuminates (is armed) when the 4wd lock switch is activated and the transmission range indicator is in low or reverse position. 26. Malfunction indicator light this light is part of an onboard diagnostic system called obd that monitors emissions, engine, ...

  • Page 179

    29. Electronic stability program (esp) indicator light/traction control system (tcs) indicator light — if equipped if this indicator light flashes during accelera- tion, apply as little throttle as possible. While driving, ease up on the accelerator. Adapt your speed and driving to the prevailing ro...

  • Page 180

    32. Electronic vehicle information center display—if equipped when the appropriate conditions exist, this display shows the electronic vehicle information center (evic) messages. 33. Electronic vehicle information center (evic) button—if equipped pushing this button, will change the display to the c...

  • Page 181

    The electronic vehicle information center (evic) fea- tures a driver-interactive display. It is located in the lower left part of the cluster below the fuel and engine tem- perature gauge. The evic consists of the following: • system status • vehicle information warning message displays • personal s...

  • Page 182

    • left/right front door ajar (one or more, with a single chime if speed is above 1 mph) • left/right rear door ajar (one or more, with a single chime if speed is above 1 mph) • door (s) ajar (with a single chime if vehicle is in motion) • gate ajar (with a single chime) • low washer fluid (with a si...

  • Page 183

    • distance to empty (dte) • elapsed time • tire pressure monitor (tpm) • personal settings to reset the display pressing and holding the evic button once will clear the function currently being displayed. Reset will only occur if a resettable function is currently being displayed. To reset all reset...

  • Page 184

    Distance to empty (dte) shows the estimated distance that can be travelled with the fuel remaining in the tank. This estimated distance is determined by a weighted average of the instantaneous and average fuel economy, according to the current fuel tank level. This is not resettable. Note: significa...

  • Page 185

    Language when in this display you may select different languages for all display nomenclature, including the trip functions. Pressing the evic button while in this display selects english, espanol, deutsch, italiano, or francais depend- ing on availability. As you continue the displayed infor- matio...

  • Page 186

    Sound horn with remote key lock when on is selected a short horn sound will occur when the remote keyless entry “lock” button is pressed. This feature may be selected with or without the flash lights on lock/unlock feature. Press and hold the evic button when in this display until “on” or “off” appe...

  • Page 187

    Power outlets will remain active for up to 60 minutes after the ignition switch has been turned off. Opening a vehicle door will cancel this feature. Press and hold the evic button when in this display until “off”, “45 sec.”, “5 min.”, or “10 min.” appears to make your selection. Turn headlamps on w...

  • Page 188

    Note: magnetic materials should be kept away from the instrument panel. This is where the compass sensor is located. Understanding your instrument panel 187 4.

  • Page 189

    To set the variance: with the ignition in the on position, with a short button press (less than one second) press and release the evic button several times until you have displayed the personal settings (customer program- mable features) menu. Once in the personal settings (customer programmable fea...

  • Page 190

    Programmable features) menu, press and release (less than one second) the evic button several times until “calibrate compass (yes)” is displayed. Using a long button press (more than one second), pressing the evic button will place the compass in calibration mode. The cal indicator will come on cont...

  • Page 191

    Electrical disturbances radio waves may pick up electrical disturbances during transmission. They mainly affect the wave amplitude, and thus remain a part of the am reception. They interfere very little with the frequency variations that carry the fm signal. Am reception am sound is based on wave am...

  • Page 192

    Clock setting procedure 1. Press and hold the time button until the hours blink. 2. Adjust the hours by turning the right side tune / audio control. 3. After the hours are adjusted, press the right side tune / audio control to set the minutes. 4. Adjust the minutes using the right side tune / audio ...

  • Page 193

    Operating instructions - radio mode note: the ignition switch must be in the on or acc position to operate the radio. Power switch/volume control (rotary) press the on/vol control to turn the radio on. Press the on/vol a second time to turn off the radio. Electronic volume control the electronic vol...

  • Page 194

    Note: in hands free phone (if equipped) mode, the mute button mutes the microphone. Scan button (radio mode) pressing the scan button causes the tuner to search for the next listenable station in either, am, fm, or satellite (if equipped) frequencies, pausing for 5 seconds at each listenable station...

  • Page 195

    Tune control (radio mode) turn the right side rotary control clockwise to increase or counter-clockwise to decrease the frequency. Am/fm button (radio mode) press the button to select am or fm modes. Setting the tone, balance, and fade press the rotary tune control and bass will display. Turn the tu...

  • Page 196

    Selected within 5 seconds after pressing the set button, the station will continue to play but will not be stored into push-button memory. You may add a second station to each push-button by repeating the above procedure with this exception: press the set button twice and set 2 will show in the disp...

  • Page 197

    • if you insert a disc with the ignition on and the radio off, the cd will automatically be pulled into the cd player. • this radio does not play discs with mp3 tracks. Seek button (cd mode) press the right side of the seek button for the next track on the cd. Press the left side of the button to re...

  • Page 198

    Rnd/set button (random play button) (cd mode) press this button while the cd is playing to activate random play. This feature plays the selections on the compact disc in random order to provide an interesting change of pace. Press the seek button to move to the next randomly selected track. Press an...

  • Page 199

    Mute button (auxiliary mode) press the mute button to cancel the sound from the speakers. 9mute9 will display. Press the mute button a second time and the sound from the speakers will return. Rotating the volume control or turning off the ignition will also return the sound from the speakers. Scan b...

  • Page 200

    Operating instructions - satellite radio — if equipped refer to the “satellite radio” section of the owner’s manual. Sales code raq – am/fm/cd (6-disc) radio with optional satellite radio, hands free phone, and vehicle entertainment systems (ves) capabilities note: the radio sales code is located on...

  • Page 201

    Power switch/volume control (rotary) press the on/vol control to turn the radio on. Press the on/vol a second time to turn off the radio. Electronic volume control the electronic volume control turns continuously (360 degrees) in either direction without stopping. Turning the volume control to the r...

  • Page 202

    Scan button (radio mode) pressing the scan button causes the tuner to search for the next listenable station, in either am, fm or satellite (if equipped) frequencies, pausing for 5 seconds at each listenable station before continuing to the next. To stop the search, press scan a second time. Msg or ...

  • Page 203

    Am/fm button (radio mode) press the button to select am or fm modes. Setting the tone, balance, and fade press the rotary tune control and bass will display. Turn the tune control to the right or left to increase or decrease the bass tones. Press the rotary tune control a second time and mid will di...

  • Page 204

    Program type 16 digit-character dis- play no program type or un- defined none adult hits adult_hits alert alert alert alert classical classical classic rock classic_rock college college country country emergency test emergency test foreign language foreign_language information information jazz jazz ...

  • Page 205

    If a preset button is activated while in the pty (program type) mode, the pty mode will be exited and the radio will tune to the preset station. Set/dir button (radio mode) — to set the push-button memory when you are receiving a station that you wish to commit to push-button memory, press the set/d...

  • Page 206

    Compact discs (cd-rw) compact discs with mp3 tracks and multisession compact discs with cd and mp3 tracks. Inserting compact disc(s) gently insert one cd into the cd player with the cd label facing up. The cd will automatically be pulled into the cd player and the cd icon will illuminate on the radi...

  • Page 207

    Scan button (cd mode for cd audio play) press the scan button to scan through each track on the cd currently playing. Load/eject button (cd mode for cd audio play) load/ eject - load press the load/ eject button and the push- button with the corresponding number where the cd is being loaded. The rad...

  • Page 208

    9insert disc” for 10 seconds. If no discs are inserted within 10 seconds “no discs loaded” will be dis- played. On some vehicles a disc can be ejected with the radio and ignition off. Time button (cd mode for cd audio play) press this button to change the display from a large cd playing time display...

  • Page 209

    Notes on playing mp3 files the radio can play mp3 files, however, acceptable mp3 file recording media and formats are limited. When writing mp3 files, pay attention to the following restric- tions. Supported media (disc types) the mp3 file recording media supported by the radio are cd-rom, cd-r and ...

  • Page 210

    Supported mp3 file formats the radio will recognize only files with the *.Mp3 exten- sion as mp3 files. Non-mp3 files named with the *.Mp3 extension may cause playback problems. The radio is designed to recognize the file as an invalid mp3 and will not play the file. When using the mp3 encoder to co...

  • Page 211

    Playback of mp3 files when a medium containing mp3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the mp3 files. Loading times for playback of mp3 files may be affected by the following: • med...

  • Page 212

    Load / eject - eject press the load/ eject button and the push- button with the corresponding number where the cd was loaded and the disc will unload and move to the entrance for easy removal. Radio display will show 9ejecting disc9 when the disc is being ejected and prompt the user to remove the di...

  • Page 213

    Am/fm button (cd mode for mp3 play) switches back to radio mode. Rnd/ pty button (cd mode for mp3 play) pressing this button plays files randomly. Set/dir button (cd mode for mp3 play) press the set/dir button to display folders, when playing an mp3 discs that have a file/folder structure. Turn the ...

  • Page 214

    Sales code rec — am/fm/cd (6–disc) radio with navigation system satellite navigation radio with cd player with mp3 capability (rec) - combines a global-positioning system-based navigation system with an integrated color screen to provide maps, turn identification, selection menus and instructions fo...

  • Page 215

    The worldwide standard for time. This makes the sys- tem’s clock very accurate once the appropriate time zone and daylight savings information is set. 1. At the main menu screen, highlight “clock setup” and press enter or press and hold for 3 seconds the time button on the unit’s faceplate. The cloc...

  • Page 216

    1. At the clock setup screen highlight “displayed clock: user defined clock”. 2. To increase the clock by hours, make sure “hr +” is highlighted and press enter. Press enter again to increase the clock by another hour. You will see on the “user defined time” display the number of hours you have incr...

  • Page 217

    1. When you are at an audio screen, quickly press the time button on the navigation faceplate. 2. In this example the large clock appears on the screen. 3. To switch the clock to the small clock, quickly press time again. 4. To toggle back to the large clock, simply press time. 216 understanding you...

  • Page 218

    Satellite radio — if equipped satellite radio uses direct satellite to receiver broadcast- ing technology to provide clear digital sound, coast to coast. The subscription service provider is sirius™ satel- lite radio. This service offers over 100 channels of music, sports, news, entertainment, and p...

  • Page 219

    Esn/sid access with raq radios with the ignition switch in the accessory position and the radio off, press the cd eject and time buttons simultaneously for 3 seconds. All twelve esn/sid num- bers will be displayed. The radio will exit the esn/sid mode when any other button is pushed, the ignition is...

  • Page 220

    Press and release the scan button (if equipped) to automatically change channels every 7 seconds. The radio will pause on each channel for 7 seconds before moving on to the next channel. The word 9scan9 will appear in the display between each channel change. Press the scan button a second time to st...

  • Page 221

    Pty button ( seek ( when the desired program is obtained, press the 9seek9 button within five seconds. The channel will change to the next channel that matches the program type selected. Satellite antenna to ensure optimum reception, do not place items on the roof around the rooftop antenna location...

  • Page 222

    Remote sound system controls — if equipped the remote sound system controls are located on the rear surface of the steering wheel. Reach behind the wheel to access the switches. The right hand control is a rocker type switch with a push button in the center. Pressing the top of the switch will incre...

  • Page 223

    The button located in the center of the left hand control will tune to the next pre-set station that you have programmed in the radio pre-set push-buttons. Cd player pressing the top of the switch once will go to the next track on the cd. Pressing the bottom of the switch once will go to the beginni...

  • Page 224

    Radio operation and cellular phones under certain conditions, the cellular phone being on in your vehicle can cause erratic or noisy performance from your radio. This condition may be lessened or eliminated by relocating the cellular phone antenna. This condition is not harmful to the radio. If your...

  • Page 225

    The air conditioning system of your vehicle contains r-134a, a refrigerant that does not deplete the ozone layer in the upper atmosphere. The controls are as follows: fan control use this control to regulate the amount of air forced through the system in any mode you select. The fan speed increases ...

  • Page 226

    Note: there is a difference in temperature between the upper and lower outlets for added comfort. The warmer air goes to the floor outlets. This feature gives improved comfort during sunny but cool conditions. Floor air is directed through the floor outlets and side window demist outlets with a smal...

  • Page 227

    Note: for maximum airflow to the rear seat passen- gers, the center instrument panel outlets can be aimed, so that the left center outlet is directed toward the right rear passenger and the right center outlet is directed toward the left rear passenger. Temperature control use this control to regula...

  • Page 228

    Note: see “circulation control” later in this section, for proper or extended use of this position. Air conditioning (normal) use this button to engage the air conditioning. A lamp will illuminate when the air con- ditioning system is engaged. Once the air conditioning is engaged, use a combination ...

  • Page 229

    Note: continuous use of the recirculate mode may make the inside air stuffy and window fogging may occur. Extended use of this mode is not recommended. In cold or damp weather, the use of the recirculate position will cause windows to fog on the inside because of moisture build up inside the vehicle...

  • Page 230

    Operating tips understanding your instrument panel 229 4.

  • Page 231

    Window fogging vehicle side windows tend to fog on the inside in mild rainy or humid weather. To clear the windows, set mode to the mix or defrost position. Direct the panel outlets toward the side windows. Do not use recirculate without a/c for long periods as fogging may occur. Interior fogging on...

  • Page 232

    The blower air will heat faster in cold weather if you use only a low blower speed for the first few minutes of vehicle operation. Side window demisters a side window demister outlet is at each end of the instrument panel. These nonadjustable outlets direct air toward the side windows when the syste...

  • Page 234: Starting And Operating

    Starting and operating contents m starting procedures . . . . . . . . . . . . . . . . . . . . . 237 ▫ automatic transaxle . . . . . . . . . . . . . . . . . . . 237 ▫ manual transaxle . . . . . . . . . . . . . . . . . . . . . 238 ▫ normal starting . . . . . . . . . . . . . . . . . . . . . . 238 ▫ ext...

  • Page 235

    ▫ off-road driving tips and vehicle characteristics . . . . . . . . . . . . . . . . . . . . . . . 247 ▫ freedom drive ii 4wd system operation . . . . 248 ▫ freedom drive ii – off-road features . . . . . . . 249 ▫ high mobility characteristics . . . . . . . . . . . . . 250 ▫ water fording characteris...

  • Page 236

    M tires — general information . . . . . . . . . . . . . . . 285 ▫ tire pressure . . . . . . . . . . . . . . . . . . . . . . . . . 285 ▫ tire inflation pressures . . . . . . . . . . . . . . . . . 286 ▫ radial-ply tires . . . . . . . . . . . . . . . . . . . . . . 289 ▫ compact spare tire — if equipped...

  • Page 237

    ▫ fuel system cautions . . . . . . . . . . . . . . . . . . 305 ▫ carbon monoxide warnings . . . . . . . . . . . . . . 306 m adding fuel . . . . . . . . . . . . . . . . . . . . . . . . . . 307 ▫ fuel filler cap (gas cap) . . . . . . . . . . . . . . . 307 ▫ loose fuel filler cap message . . . . . . . ...

  • Page 238

    Starting procedures before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. Warning! Never leave children alone in a vehicle. Leaving children in a vehicle unattended is dangerous for a number of reasons. A child or others could be seri- ou...

  • Page 239

    Manual transaxle before starting the engine fully apply the parking brake, press the clutch pedal to the floor and place the gear selector in neutral. Note: the engine will not start unless the clutch pedal is pressed to the floor. Note: if key won’t turn and steering wheel is locked, rotate the whe...

  • Page 240

    If engine fails to start if the engine fails to start after you have followed the “normal starting” procedure, it may be flooded. Push the accelerator pedal all the way to the floor and hold it there. Crank the engine for no more than 15 seconds. This should clear any excess fuel in case the engine ...

  • Page 241

    Automatic transaxle — if equipped caution! Damage to the transaxle may occur if the following precautions are not observed: • shift into park only after the vehicle has come to a complete stop. • shift into or out of reverse only after the vehicle has come to a complete stop and the engine is at idl...

  • Page 242

    Warning! It is dangerous to shift the selector lever out of “p” or “n” if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in reverse. You could lose control of the vehicle and hit someone or something. Only sh...

  • Page 243

    Gear ranges for continuously variable automatic transaxle (cvt) do not race the engine when shifting from park or neutral positions into another gear range. “p” park supplements the parking brake by locking the transmis- sion. The engine can be started in this range. Never use p (park) while the veh...

  • Page 244

    • when shifting into p (park), firmly move the lever all the way forward until it stops. • look at the shift indicator window on the console to ensure it is in the p (park) position. • you must depress the brake pedal to move the shift lever out of the p (park) position. Caution! Before moving the s...

  • Page 245

    Manual transaxle operation warning! You or others could be injured if you leave the vehicle unattended without having the parking brake fully applied. The parking brake should al- ways be applied when the driver is not in the vehicle, especially on an incline. Fully depress the clutch pedal before y...

  • Page 246

    Use each gear in numerical order - do not skip a gear. Be sure the transaxle is in first gear, (not third), when starting from a standing position. Damage to the clutch can result from starting in third. For most city driving you will find it easier to use only the lower gears. For steady highway dr...

  • Page 247

    Caution! If you skip more than one gear while downshifting or downshift at too high a vehicle speed, you could damage the engine, transmission, or clutch. To maintain a safe speed and prolong brake life, shift down to 2nd or 1st when descending a steep grade. When turning a corner, or driving up a s...

  • Page 248

    Traction surfaces, activate the 4wd lock switch by pull- ing up once and releasing. This locks the center coupling allowing more torque to be sent to the rear wheels. The amber 94wd9 light will come on in the cluster. This can be done on the fly, at any vehicle speed. To deactivate, simply pull on t...

  • Page 249

    The package includes: • 2.4l dohc 16-valve i4 (172 bhp @ 6000 rpm, 165 lb-ft @ 4400 rpm) • second generation continuously variable transaxle (cvt2l) with 19:1 crawl ratio • tow hooks: 2 front and 1 rear • front engine and transaxle skid plate • fuel tank skid plate • air filtration system • unique s...

  • Page 250

    Roads. The active four wheel drive mode has the same functionality with the freedom drive i system. Shifting the transaxle gear select lever into low off-road mode with the 4wd lock lever active, lights the amber off-road and 4wd cluster lights. This off-road mode gives the combined benefits of a 19...

  • Page 251

    Improved traction capability off-road. It also, turns on other system features in conjunction with l off-road mode. • unique engine calibration – when the system has the 4wd lock lever engaged and is in the low off-road mode or reverse, the engine calibration changes to run higher spark advance with...

  • Page 252

    Angles a b c d starting and operating 251 5.

  • Page 253

    Water fording characteristics water fording characteristics is the vehicle’s ability to cross a body of still water, where the powertrain and drivetrain are safe from water ingestion. The patriot with the freedom drive ii off-road package has high water fording characteristics with the ability to cr...

  • Page 254

    Water fording characteristics starting and operating 253 5.

  • Page 255

    The basics of off-road driving you will encounter many types of terrain driving off- road. You should be familiar with the terrain and area before proceeding. There are many types of surface conditions: hard packed dirt, gravel, rocks, grass, sand, mud, snow and ice. Every surface has a different ef...

  • Page 256

    Additional traction and activates the numerous off-road features to improve handling and control on slippery or difficult terrain. Due to the sustained lower gearing, low (l off-road) with 4wd lock engaged will allow the engine to operate in a higher power range. This will allow you to cross over ob...

  • Page 257

    Caution! On icy or slippery roads, do not downshift at high engine rpm’s or vehicle speeds because engine brak- ing may cause skidding and loss of control. • mud – deep mud creates a great deal of suction around the tires and is very difficult to get through. You should use low (l off-road) with the...

  • Page 258

    On pavement or other hard surfaces. Be sure you have a way to air the tires back up prior to reducing the pressure. Caution! Reduced tire pressures may cause tire unseating and total loss of air pressure. To reduce the risk of tire unseating, while at a reduced tire pressure, reduce your speed and a...

  • Page 259

    Stand a safe distance in front of you where they can see the obstacle, watch your tires and undercarriage, and guide you through. Crossing large rocks when approaching large rocks, choose a path which ensures you drive over the largest of them with your tires. This will lift your undercarriage over ...

  • Page 260

    Dirt to fill the rut ahead of the turnout you just created. You should now be able to drive out following the trench you just created at a 45-degree angle. Warning! There is an increased risk of roll over when crossing an obstacle, at any angle, with steep sides. Crossing logs to cross a log, approa...

  • Page 261

    Caution! Winching or rocking the vehicle off hard objects increases the risk of underbody damage. Hill climbing hill climbing requires good judgment and a good under- standing of your abilities and your vehicle’s limitations. Hills can cause serious problems. Some are just too steep to climb and sho...

  • Page 262

    A 1/4; turn quickly back and forth. This will provide a fresh 9bite9 into the surface and will usually provide enough traction to complete the climb. If you do not make it to the top, place the vehicle in reverse and back straight down the grade using engine resistance along with the vehicle brakes....

  • Page 263

    The possibilities of a down hill slide or roll over. Make sure the surface has good traction with firm and stable soils. If possible transverse the incline at an angle heading slightly up or down. Warning! Driving across an incline increases the risk of a roll over, which may result in severe injury...

  • Page 264

    Avoid damage to the environment. You should know your vehicles abilities and be able to recover it if some- thing goes wrong. You should never stop or shut a vehicle off when crossing deep water unless you ingested water into the engine air intake. If the engine stalls do not attempt to restart it. ...

  • Page 265

    • before you cross any type of water – as you approach any type of water you need to determine if you can cross it safely and responsibly. If necessary, get out and walk through the water or probe it with a stick. You need to be sure of its depth, approach angle, current and bottom condition. Be car...

  • Page 266

    Your tires putting you and your vehicle in jeopardy. There is still a high risk of personal injury and vehicle damage with slower water currents in depths greater than the vehicle’s running ground clearance. You should never attempt to cross flowing water which is deeper than the vehicle’s running g...

  • Page 267

    Replace it so, start high and lower it as required. Remem- ber you must return the tires to normal air pressure before driving on road or at highway conditions. Be sure you have a way to return the tires to their normal on road air pressure. Caution! Reduced tire pressure increases the risk of tire ...

  • Page 268

    Surroundings, then using a tow strap to the vehicle tow hooks would be fast and easy. If the vehicle is severely hung up or in a situation where great care needs to be taken during the recovery, then nothing can do the job better than a winch. If you are severely hung up on something you should jack...

  • Page 269

    Caution! Damage can occur when spinning your tires at an excessive high speed. Do not spin your tires faster than an indicated 30 mph (48 km/h) • using the tow hooks with a tow strap – tow straps are a quick and easy way to recover your vehicle from minor situations if you have a secondary vehicle w...

  • Page 270

    Warning! Never use tow straps with end hooks or link two straps with a clevis pin. These heavy metal objects could become projectiles if a strap breaks, which could cause severe injury. Never leave more than 2 to 3 ft. (61 to 91 cm) of slack in the strap. More slack than this greatly increases the r...

  • Page 271

    Warning! Abrasive material in any part of the brakes may cause excessive wear or unpredictable braking. You might not have full braking power when you need it to prevent an accident. If you have been operating your vehicle in dirty conditions, get your brakes checked and cleaned as necessary. Failur...

  • Page 272

    When parking on a hill, it is important to set the parking brake before placing the gear selector in park, otherwise the load on the automatic transaxle locking mechanism may make it difficult to move the selector out of park. As an added precaution, turn the front wheels toward the curb on a downhi...

  • Page 273

    Brake system your vehicle is equipped with power assisted brakes as standard equipment. In the event power assist is lost for any reason (for example, repeated brake applications with the engine off), the brakes will still function. How- ever, the effort required to brake the vehicle will be much gr...

  • Page 274

    Anti-lock brake system (abs) — if equipped the anti-lock brake system provides increased vehicle stability and brake performance under most braking conditions. The system automatically “pumps” the brakes during severe braking conditions to prevent wheel lock-up. Warning! Pumping of the anti-lock bra...

  • Page 275

    Warning! • anti-lock system (abs) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency beyond that afforded by the condition of the vehicle brakes and tires or the traction afforded. • the abs cannot prevent accidents, including th...

  • Page 276

    When the vehicle is driven over 7 mph (11 km/h), you may also hear a slight clicking sound as well as some related motor noises. These noises are the system per- forming its self check cycle to ensure that the abs system is working properly. This self check occurs each time the vehicle is started an...

  • Page 277

    Power steering the standard power steering system will give you good vehicle response and increased ease of maneuverability in tight spaces. The system will provide mechanical steering capability if power assist is lost. If for some reason the power assist is interrupted, it will still be possible t...

  • Page 278

    Tire safety information tire markings note: • p (passenger)-metric tire sizing is based on u.S. Design standards. P-metric tires have the letter “p” molded into the sidewall preceding the size designation. Ex- ample: p215/65r15 95h. • european metric tire sizing is based on european design standards...

  • Page 279

    Tire sizing chart example: size designation: p = passenger car tire size based on u.S. Design standards (....Blank....( = passenger car tire based on european design standards lt = light truck tire based on u.S. Design standards t = temporary spare tire 31 = overall diameter in inches (in) 215 = sec...

  • Page 280

    Example: service description: 95 = load index —a numerical code associated with the maximum load a tire can carry. H = speed symbol —a symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions. —the maximum speed corresp...

  • Page 281

    Tire identification number (tin) the tin may be found on one or both sides of the tire; however, the date code may only be on one side. Tires with white sidewalls will have the full tin including date code located on the white sidewall side of the tire. Look for the tin on the outboard side of black...

  • Page 282

    Tire loading and tire pressure tire placard location note: the proper cold tire inflation pressure is listed on either the face of the driver’s door or the driver’s side “b” pillar. Tire and loading information placard this placard tells you important information about the: 1) number of people that ...

  • Page 283

    3) the tire size designed for your vehicle 4) the cold tire inflation pressures for the front, rear, and spare tires. Loading the vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhe...

  • Page 284

    4. The resulting figure equals the available amount of cargo and luggage load capacity. For example, if “xxx” amount equals 1400 lbs. And there will be five 150 lb. Passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lbs. (since 5 x 150 = 750, and 1400 – 750 = ...

  • Page 285

    284 starting and operating.

  • Page 286

    Warning! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. Tires — general information tire pressure proper tire inflation pressur...

  • Page 287

    2. Economy— improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Under inflation, also increases tire rolling resistance and results in higher fuel consump- ...

  • Page 288

    The pressure should be checked and adjusted as well as inspecting for signs of tire wear or visible damage at least once a month. Use a good quality pocket-type gauge to check tire pressure. Do not make a visual judgement when determining proper inflation. Radial tires may look properly inflated eve...

  • Page 289

    Tire pressure may increase from 2 to 6 psi (13 to 40 kpa) during operation. Do not reduce this normal pressure build up or your tire pressure will be too low. Tire pressures for high speed operation the manufacturer advocates driving at safe speeds within posted speed limits. Where speed limits or c...

  • Page 290

    Radial-ply tires warning! Combining radial ply tires with other types of tires on your vehicle will cause your vehicle to handle poorly. The instability could cause an accident. Al- ways use radial ply tires in sets of four (or 6, in case of trucks with dual rear wheels). Never combine them with oth...

  • Page 291

    Do not install a wheel cover or attempt to mount a conventional tire on the compact spare wheel, since the wheel is designed specifically for the compact spare. Do not install more than one compact spare tire/wheel on the vehicle at any given time. Caution! Because of the reduced ground clearance, d...

  • Page 292

    Tire spinning when stuck in mud, sand, snow, or ice conditions, do not spin your vehicle’s wheels above 30 mph (48 km/h) or for more than 30 seconds. Refer to the paragraph on “freeing a stuck vehicle” in section 6 of this manual. Warning! Fast spinning tires can be dangerous. Forces gener- ated by ...

  • Page 293

    These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth becomes 1/16 inch (2 mm). When the tread is worn to the tread wear indicators, the tire should be replaced. Many states have laws requiring tire replacement at this point. Life of tire th...

  • Page 294

    “tread wear indicators”). Refer to the “tire and loading information” placard for the size designation of your tire. The service description and load identification will be found on the original equipment tire. Failure to use equivalent replacement tires may adversely affect the safety, handling, an...

  • Page 295

    Caution! Replacing original tires with tires of a different size may result in false speedometer and odometer readings. Alignment and balance poor suspension alignment may result in: • fast tire wear. • uneven tire wear, such as feathering and one-sided wear. • vehicle pull to right or left. Tires m...

  • Page 296

    Based on cold inflation tire pressure. This is defined as the tire pressure after a vehicle has not been driven for more than 3 hours - and in outside ambient tempera- ture. Refer to the “tires – general information” in this section for information on how to properly inflate the vehicle’s tires. The...

  • Page 297

    Premium system – if equipped the tire pressure monitor system (tpms) uses wireless technology with wheel rim mounted electronic sensors to monitor tire pressure levels. Sensors, mounted to each wheel as part of the valve stem, transmit tire pressure readings to the receiver module. Note: it is parti...

  • Page 298

    Display settings • your system can be set to display pressure units in psi, kpa, or bar. Note: these display settings may not be available due to regulatory authorities. In this case, the display will only show approved units. Note: a low spare tire will not cause the tire pressure monitoring tellta...

  • Page 299

    Check tpm system message the tire pressure monitoring telltale light will flash on and off for 60 seconds, and an audible chime will sound when a system fault is detected. The flash cycle will repeat every ten minutes, without an audible chime, until the fault condition no longer exists. The evic wi...

  • Page 300

    Display settings • your system can be set to display pressure units in psi, kpa, or bar. Note: these display settings may not be available due to regulatory authorities. In this case, the display will only show approved units. Note: if your vehicle is equipped with a compact spare wheel and tire ass...

  • Page 301

    Caution! The tpms has been optimized for the original equipment tires and wheels. Tpms pressures have been established for the tire size equipped on your vehicle. Undesirable system operation or sensor damage may result when using replacement equip- ment that is not of the same size, type, and/or st...

  • Page 302

    Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability. • the tpms is not a substitute for proper tire mainte- nance, and it is the driver’s responsibility to maintain correct tire pressure, even if under-inflation has not reached...

  • Page 303

    Snow tires some areas of the country require the use of snow tires during winter. Standard tires are of the all season type and satisfy this requirement as indicated by the m+s designation on the tire sidewall. If you need snow tires, select tires equivalent in size and type to the original equipmen...

  • Page 304

    Wear should be corrected before rotating. The suggested rotation method is the “forward-cross” shown in the diagram. Fuel requirements gasoline engines your vehicle is designed to meet all emis- sion regulations and provide excellent fuel economy when using high quality regular unleaded gasoline wit...

  • Page 305

    Reformulated gasolines contain oxygenates, and are spe- cifically blended to reduce vehicle emissions and im- prove air quality. The manufacturer supports the use of reformulated gaso- lines. Properly blended reformulated gasolines will pro- vide excellent performance and durability of engine and fu...

  • Page 306

    Performance in some vehicles. The manufacturer recom- mends using gasolines without mmt. Since the mmt content of gasoline may not be indicated on the pump, you should ask your gasoline retailer whether or not his/her gasoline contains mmt. It is even more important to look for gasolines without mmt...

  • Page 307

    Products contain high concentrations of methanol. Fuel system damage or vehicle performance problems resulting from the use of such fuels or additives is not the responsibility of the manufacturer. Note: intentional tampering with emissions control systems can result in civil penalties being assesse...

  • Page 308

    Adding fuel fuel filler cap (gas cap) the gas cap is behind the fuel filler door, on the left side of the vehicle. If the gas cap is lost or damaged, be sure the replacement cap is for use with this vehicle. Caution! Damage to the fuel system or emission control sys- tem could result from using an i...

  • Page 309

    Note: when the fuel nozzle “clicks” or shuts off, the fuel tank is full. Warning! • never have any smoking materials lit in or near the vehicle when the gas cap is removed or the tank filled. • never add fuel when the engine is running. This is in violation of most state and federal fire regula- tio...

  • Page 310

    Problem continues, the message will appear the next time the vehicle is started. Refer to “onboard diagnostic system — obdii” in section 7 of this manual for more information. Vehicle loading vehicle loading capacities front seat occupants . . . . . . . . . . . . . . . . . . . . . . . 2 rear seat oc...

  • Page 311

    Gross trailer weight (gtw) the gross trailer weight (gtw) is the weight of the trailer plus the weight of all cargo, consumables and equipment (permanent or temporary) loaded in or on the trailer in its 9loaded and ready for operation9 condition. The recom- mended way to measure gtw is to put your f...

  • Page 312

    Frontal area the maximum height and maximum width of the front of a trailer. Trailer sway control the trailer sway control is a telescoping link that can be installed between the hitch receiver and the trailer tongue that typically provides adjustable friction associated with the telescoping motion ...

  • Page 313

    Warning! An improperly adjusted weight distributing hitch system may reduce handling, stability, braking per- formance, and could result in an accident. Weight distributing systems may not be compatible with surge brake couplers. Consult with your hitch and trailer manufacturer or a reputable recrea...

  • Page 314

    All trailer hitches should be professionally installed on your vehicle. Trailer towing weights (maximum trailer weight ratings) the following chart provides the maximum trailer weight ratings towable for your given drivetrain. Trailer towing weights (maximum trailer weight rat- ings) the following c...

  • Page 315

    Engine/transmission frontal area max. Gtw (gross trailer wt.) max. Tongue wt. (see note 1) 2.4l auto/man 22 sq. Ft. (2.04 sq. M) 1000 lbs (450 kg) 150 lbs (68 kg) 2.4l auto/man with trailer tow prep package (ahc) 32 sq. Ft. (3.0 sq. M) 2000 lbs (450 kg) 225 lbs (102 kg) refer to local laws for maxim...

  • Page 316

    Never exceed the maximum tongue weight stamped on your bumper or trailer hitch. Consider the following items when computing the weight on the rear axle of the vehicle: • the tongue weight of the trailer. • the weight of any other type of cargo or equipment put in or on your vehicle. • the weight of ...

  • Page 317

    Caution! • avoid towing a trailer for the first 500 miles (805 km) of vehicle operation. Doing so may damage your vehicle. • during the first 500 miles (805 km) of trailer towing, limit your speed to 50 mph (80 km/h). Perform the maintenance listed in section 8 of this manual. When towing a trailer,...

  • Page 318

    • safety chains must always be used between your vehicle and trailer. Always connect the chains to the frame or hook retainers of the vehicle hitch. Cross the chains under the trailer tongue and allow enough slack for turning corners. • vehicles with trailers should not be parked on a grade. When pa...

  • Page 319

    − when replacing tires refer to the tires–general infor- mation section of this manual on replacement tires for proper tire replacement procedures. Replacing tires with a higher load carrying capacity will not increase the vehicle’s gvwr and gawr limits. Towing requirements — trailer brakes − do not...

  • Page 320

    Warning! Do not connect trailer brakes to your vehicle’s hy- draulic brake lines. It can overload your brake sys- tem and cause it to fail. You might not have brakes when you need them and could have an accident. Towing any trailer will increase your stopping dis- tance. When towing you should allow...

  • Page 321

    The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector. Refer to the following illustrations. Towing tips before setting out on a trip, practice turning, stopping and backing the trailer in an area away from heavy traffic. 4 - pin connector 7-...

  • Page 322

    Towing tips — automatic transmission the automatic transmission fluid and filter should be changed if you regularly tow a trailer for more than 45 minutes of continuous operation. See schedule “b” in section 8 of this manual for transmission fluid change intervals. Note: check the automatic transmis...

  • Page 323

    Recreational towing (behind motorhome, etc.) towing this vehicle behind another vehicle (flat towing with all four wheels on the ground) caution! Do not flat tow this vehicle. Damage to the driv- etrain will result. Note: if the vehicle requires towing make sure all four wheels are off the ground. 3...

  • Page 324: Contents

    What to do in emergencies contents m hazard warning flasher . . . . . . . . . . . . . . . . . . 324 m if your engine overheats . . . . . . . . . . . . . . . . . 324 m automatic transaxle overheating . . . . . . . . . . . 326 m jacking and tire changing . . . . . . . . . . . . . . . . 326 ▫ jack loca...

  • Page 325

    Hazard warning flasher the flasher switch is located on the instrument panel, below the radio. Depress the switch and both cluster indicators and all front and rear directional signals will flash. Depress the switch again to turn hazard warning flashers off. Do not use this emergency warning system ...

  • Page 326

    The normal range. If the pointer remains on the h (red) mark for more than a minute, turn the engine off imme- diately and call for service. Note: there are steps that you can take to slow down an impending overheat condition. If your air conditioner is on, turn it off. The air conditioning system a...

  • Page 327

    Warning! A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant. You may want to call a service center if your vehicle overheats. If you decide to look under the hood yourself, refer to section 7, maintenance, of this manual. Follow the warnings und...

  • Page 328

    Jack location the jack and jack-handle are stowed under the load floor in the cargo area. Spare tire stowage the spare tire is stowed under the rear load floor in the cargo area. Spare tire removal lift up the load floor cover and remove the hold down. Preparations for jacking park the vehicle on a ...

  • Page 329

    • turn on the hazard warning flasher. • block both the front and rear of the wheel diagonally oppo- site the jacking position. For example, if changing the right front tire, block the left rear wheel. • passengers should not remain in the vehicle while the vehicle is being jacked. Jacking instructio...

  • Page 330

    3. There are two front jacking locations and two rear jacking locations on each side of the body. The front locations are outlined by two triangular cutouts, the rear ones by two rectangular cutouts. For vehicles equipped with plastic trim, the plastic has been cut away to expose the jacking locatio...

  • Page 331

    7. Lower the vehicle by turning the jack screw to the left. 8. Finish tightening the nuts. Push down on the wrench while tightening the wheel nuts. Alternate nuts until each nut has been tightened twice. Correct wheel nut torque is 100 ft. Lbs (135 n·m). If you doubt that you have tightened the nuts...

  • Page 332

    Jump-starting procedures due to a low battery warning! Take care to avoid the radiator cooling fan whenever the hood is raised. It can start anytime the ignition switch is on. You can be hurt by the fan. Warning! Do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an...

  • Page 333

    Warning! Wear eye protection and remove any metal jewelry such as watch bands or bracelets that might make an inadvertent electrical contact. You could be seriously injured. Note: disconnecting the battery with the ignition in the on position will cause vehicles with an automatic transaxle (cvt2) to...

  • Page 334

    5. Connect one end of a jumper cable to the positive terminal of the booster battery. Connect the other end of the jumper cable to the positive terminal of the dis- charged battery. Warning! Battery fluid is a corrosive acid solution; do not allow battery fluid to contact eyes, skin or clothing. Don...

  • Page 335

    Driving on slippery surfaces acceleration rapid acceleration on snow covered, wet, or other slip- pery surfaces may cause the front wheels to pull errati- cally to the right or left. This phenomenon occurs when there is a difference in the surface traction under the front (driving) wheels. Warning! ...

  • Page 336

    Freeing a stuck vehicle note: if your vehicle is equipped with traction con- trol, turn the system off before attempting to “rock” the vehicle. If your vehicle becomes stuck in mud, sand or snow, it can often be moved by a rocking motion. Turn your steering wheel right and left to clear the area aro...

  • Page 337

    Caution! Racing the engine or spinning the wheels too fast may lead to transaxle overheating and failure. It can also damage the tires. Do not spin the wheels above 30 mph (48 km/h). Do not spin the wheels continu- ously for more than 30 seconds. Towing a disabled vehicle with ignition key automatic...

  • Page 338

    Without the ignition key special care must be taken when the vehicle is towed with the ignition in the lock position. A dolly should be used under the front wheels if the rear wheels are raised. Proper towing equipment is necessary to prevent dam- age to the vehicle. Battery power is required to rel...

  • Page 340: Maintaining Your Vehicle

    Maintaining your vehicle contents m engine compartment — gasoline engines . . . . . 342 m onboard diagnostic system — obd ii . . . . . . . . 343 ▫ loose fuel filler cap message . . . . . . . . . . . . 344 m emissions inspection and maintenance programs . . . . . . . . . . . . . . . . . . . . . . . ....

  • Page 341

    ▫ front suspension ball joints . . . . . . . . . . . . . . 357 ▫ body lubrication . . . . . . . . . . . . . . . . . . . . . 358 ▫ windshield wiper blades . . . . . . . . . . . . . . . . 358 ▫ windshield washer reservoir . . . . . . . . . . . . . 359 ▫ exhaust system . . . . . . . . . . . . . . . . ....

  • Page 342

    M fluids and capacities . . . . . . . . . . . . . . . . . . . 388 m fluids, lubricants and genuine parts . . . . . . . . 388 ▫ engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 388 ▫ chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . . 389 maintaining your vehicle 341 7.

  • Page 343

    Engine compartment — gasoline engines 342 maintaining your vehicle.

  • Page 344

    Onboard diagnostic system — obd ii your vehicle is equipped with a sophisticated onboard diagnostic system called obd ii. This system monitors the performance of the emissions, engine, and automatic transaxle control systems. When these systems are oper- ating properly, your vehicle will provide exc...

  • Page 345

    Loose fuel filler cap message after fuel is added, the vehicle diagnostic system can determine if the fuel filler cap is possible loose or improperly installed. A gascap message will be dis- played in the instrument cluster. Tighten the gas cap until a 9clicking9 sound is heard. This is an indicatio...

  • Page 346

    Your vehicle has a simple ignition key actuated test, which you can use prior to going to the test station. To check if your vehicle’s obd system is ready, you must do the following: 1. Insert your ignition key into the ignition switch. 2. Turn the ignition to the on position, but do not crank or st...

  • Page 347

    Vehicle serviced before going to the i/m station. The i/m station can fail your vehicle because the mil symbol is on with the engine running. Replacement parts use of genuine mopar t parts for normal/scheduled maintenance and repairs is highly recommended to in- sure the designed performance. Damage...

  • Page 348

    Maintenance procedures the pages that follow contain the required maintenance services determined by the engineers who designed your vehicle. Besides the maintenance items for which there are fixed maintenance intervals, there are other items that should operate satisfactorily without periodic maint...

  • Page 349

    Checking the oil while the vehicle is on level ground and only when the engine is hot, will improve the accuracy of the oil level readings. Maintain the oil level between the range markings on the dipstick. The range markings will consist of a crosshatch zone that says safe or a cross- hatch zone th...

  • Page 350

    Note: if any of these apply to you then change your engine oil every 3,000 miles (5 000 km) or 3 months, whichever comes first, and follow schedule “b—all engines” of the 9maintenance schedules9 section of this manual. If none of these apply to you, then change your engine oil at every interval show...

  • Page 351

    Lubricants which do not have both, the engine oil certi- fication mark and the correct sae viscosity grade num- ber should not be used. Synthetic engine oils there are a number of engine oils being promoted as either synthetic or semi-synthetic. If you chose to use such a product, use only those oil...

  • Page 352

    Drive belt – check condition at the mileage shown in the maintenance schedules, check the drive belt for condition. Inspect the drive belt for evidence of cuts, cracks, or glazing and replace belt if any sign of damage which could result in belt failure. The belt is self-tensioning and will not need...

  • Page 353

    Caution! Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition. In the event of engine malfunction, particularly involv- ing engine misfire or other apparent loss of perfor- mance, have your vehicle serviced promptly. Contin- ued operation of your veh...

  • Page 354

    To minimize the possibility of catalyst damage: • do not shut off the engine or interrupt the ignition when the transaxle is in gear and the vehicle is in motion. • do not try to start the engine by pushing or towing the vehicle. • do not idle the engine with any spark plug wires disconnected for pr...

  • Page 355

    Warning! The air cleaner can provide a measure of protection in the case of engine backfire. Do not remove the air cleaner unless such removal is necessary for repair or maintenance. Make sure that no one is near the engine compartment before starting the vehicle with the air cleaner removed. Failur...

  • Page 356

    Warning! Battery fluid is a corrosive acid solution and can burn or even blind you. Don’t allow battery fluid to contact your eyes, skin or clothing. Don’t lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area immediately with large amounts of water. Battery ...

  • Page 357

    Air conditioner maintenance for best possible performance, your air conditioner should be checked and serviced by an authorized dealer at the start of each warm season. This service should include cleaning of the condenser fins and a performance test. Drive belt tension should also be checked at thi...

  • Page 358

    Refrigerant recovery and recycling r-134a air conditioning refrigerant is a hydrofluorocar- bon (hfc) that is endorsed by the environmental pro- tection agency and is an ozone-saving product. How- ever, the manufacturer recommends that air conditioning service be performed by dealers or other servic...

  • Page 359

    Body lubrication locks and all body pivot points, including such items as seat tracks, doors, liftgate and hood hinges, should be lubricated periodically to assure quiet, easy operation and to protect against rust and wear. Prior to the appli- cation of any lubricant, the parts concerned should be w...

  • Page 360

    2. Push the release tab and slide the wiper blade assem- bly down along the arm. Gently place the wiper arm on the windshield. 3. Install the new blade assembly onto the wiper arm tip until it locks in place. Windshield washer reservoir the washer fluid reservoir is located in the rear of the engine...

  • Page 361

    Cooling system warning! • when working near the radiator cooling fan, dis- connect the fan motor lead or turn the ignition switch to the off position. The fan is temperature controlled and can start at any time the ignition switch is in the on position. • you or others can be badly burned by hot coo...

  • Page 362

    System cleaner. Follow with a thorough rinsing to remove all deposits and chemicals. Properly dispose of old antifreeze solution. Selection of coolant use only the manufacturers recommended coolant, refer to fluids, lubricants and genuine parts for correct coolant type. Caution! Mixing of coolants o...

  • Page 363

    Adding coolant your vehicle has been built with an improved engine coolant that allows extended maintenance intervals. This coolant can be used up to 5 years or 100,000 miles before replacement. To prevent reducing this extended mainte- nance period, it is important that you use the same coolant thr...

  • Page 364

    Warning! • the warning words “do not open hot” on the cooling system pressure cap are a safety pre- caution. Never add coolant when the engine is overheated. Do not loosen or remove the cap to cool an overheated engine. Heat causes pressure to build up in the cooling system. To prevent scald- ing or...

  • Page 365

    When additional coolant is needed to maintain the proper level, it should be added to the coolant bottle. Do not overfill. Points to remember note: when the vehicle is stopped after a few miles (a few kilometers) of operation, you may observe vapor coming from the front of the engine compartment. Th...

  • Page 366

    • do not change the thermostat for summer or winter operation. If replacement is ever necessary, install only the correct type thermostat. Other designs may result in unsatisfactory coolant performance, poor gas mileage, and increased emissions. Hoses and vacuum/vapor harnesses inspect surfaces of h...

  • Page 367

    Brake system in order to assure brake system performance, all brake system components should be inspected periodically. Suggested service intervals can be found in the mainte- nance section. Warning! Riding the brakes can lead to brake failure and possibly an accident. Driving with your foot resting...

  • Page 368

    Note: inspection of brake hoses should be done when- ever the brake system is serviced and at every engine oil change. Warning! Worn brake hoses can burst and cause brake failure. You could have an accident. If you see any signs of cracking, scuffing, or worn spots, have the brake hoses replaced imm...

  • Page 369

    Warning! Use of a brake fluid that may have a lower initial boiling point or unidentified as to specification, may result in sudden brake failure during hard prolonged braking. You could have an accident. Caution! Use of improper brake fluids will affect overall clutch system performance. Improper b...

  • Page 370

    Steel belt traction on the drive and driven pulleys. Refer to fluids, lubricants and genuine parts for correct fluid type. Caution! Using a transmission fluid other than the manufac- turers recommended fluid will cause belt slip and result in a complete transmission failure! Refer to fluids, lubrica...

  • Page 371

    Fluid level check check the fluid level by removing the fill plug. The fluid level should be between the bottom of the fill hole and a point not more that 3/16” (4.7 mm) below the bottom of the hole. Add fluid, if necessary, to maintain the proper level. Frequency of fluid change under normal operat...

  • Page 372

    Power transfer unit (ptu) – awd/4wd models only lubricant selection use only manufacturers recommended fluid. Refer to fluids, lubricants and genuine parts for correct fluid type. Fluid level check visually inspected the unit at each oil change for leakage. If leakage is detected, check the fluid le...

  • Page 373

    The most common causes are: • road salt, dirt and moisture accumulation. • stone and gravel impact. • insects, tree sap and tar. • salt in the air near sea coast localities. • atmospheric fallout/industrial pollutants. Washing • wash your vehicle regularly. Always wash your ve- hicle in the shade us...

  • Page 374

    • it is important that the drain holes in the lower edges of the doors, rocker panels and trunk be kept clear and open. • if you detect any stone chips or scratches in the paint, touch them up immediately. The cost of such repairs is considered the responsibility of the owner. • if your vehicle is d...

  • Page 375

    • remove as much of the stain as possible by blotting with a clean, dry towel. • blot any remaining stain with a clean, damp towel. • for tough stains, apply mopart total clean or a mild soap solution to a clean, damp cloth and remove stain. Use a fresh, damp towel to remove soap residue. • for grea...

  • Page 376

    Warning! Do not use volatile solvents for cleaning purposes. Many are potentially flammable, and if used in closed areas they may cause respiratory harm. Cleaning headlights your vehicle has plastic headlights that are lighter and less susceptible to stone breakage than glass headlights. Plastic is ...

  • Page 377

    Cleaning plastic instrument cluster lenses the lenses in front of the instruments in this vehicle are molded in clear plastic. When cleaning the lenses, care must be taken to avoid scratching the plastic. 1. Clean with a wet soft rag. A mild soap solution may be used, but do not use high alcohol con...

  • Page 378

    Cavity cartridge fuse mini fuse description 1 empty empty 2 15 amp lt. Blue awd/4wd ecu feed 3 10 amp red chmsl brake switch feed 4 10 amp red ignition switch feed 5 20 amp yellow trailer tow 6 10 amp red iod sw/pwr mir/ ocm steering cntrl sdar/hands free phone 7 30 amp green iod sense1 8 30 amp gre...

  • Page 379

    Cavity cartridge fuse mini fuse description 17 10 amp red iod feed mod-wcm 18 40 amp green asd relay contact pwr feed 19 20 amp yellow pwr amp 1 & amp 2 feed 20 15 amp lt. Blue iod feed radio 21 10 amp red iod feed intrus mod/siren 22 10 amp red ign run heat/ac/ compass sensor 23 15 amp lt. Blue eng...

  • Page 380

    Cavity cartridge fuse mini fuse description 33 10 amp red abs mod/j1962 conn/pcm 34 30 amp pink abs valve feed 35 40 amp green abs pump feed 36 30 amp pink headlamp /washer control / smart glass 37 25 amp natural 110 inverter caution! • when installing the integrated power module cover, it is import...

  • Page 381

    Vehicle storage if you will not be using your vehicle for more than 21 days you may want to take steps to preserve your battery. You may: • disengage the mini fuse in the power distribution center labeled iod (ignition off-draw). • or, disconnect the negative cable from the battery. Replacement bulb...

  • Page 382

    Bulb replacement headlamps • raise the hood and locate connector behind the head- lamp. Locating headlamp connector releasing red lock tab maintaining your vehicle 381 7.

  • Page 383

    • reach into engine compartment and pull red lock out at connector. • twist the bulb to the left and pull outward from assembly. Remove green connector from back of bulb by pulling straight back twisting bulb from socket 382 maintaining your vehicle.

  • Page 384

    Note: these are halogen bulbs. Take care not to touch the bulb with your fingers. Body oils from your fingers could cause excessive heat buildup which reduces bulb life. Fog lights see your authorized dealer for replacement. Removing halogen bulb from assembly maintaining your vehicle 383 7.

  • Page 385

    Tail lights, rear turn signals and backup lights — replacement 1. Remove the two push-pins from the tail light housing. 2. Grasp the tail lamp and pull firmly to disengage the lamp from the aperture panel. Removing push-pins push-pins removed 384 maintaining your vehicle.

  • Page 386

    3. Twist and remove socket from lamp. Pulling lamp from body removing socket and bulb maintaining your vehicle 385 7.

  • Page 387

    4. Remove bulb from socket and replace. License lights 1. Use a screw driver to gently pry against the side of the snap tab to remove the lamp from the liftgate. 2. Rotate the socket 1/4 turn counterclockwise. Removing bulb from socket prying lamp from liftgate 386 maintaining your vehicle.

  • Page 388

    3. Pull bulb from socket. Center high-mounted stoplight light is an led assembly. See your authorized dealer for replacement. Removing socket from lamp removing bulb from socket maintaining your vehicle 387 7.

  • Page 389

    Fluids and capacities u.S. Metric fuel (approximate) 13.5 gallons 51.0 liters engine oil-with filter all gasoline engines (use api certified sae 5w-20 engine oil.) 4.5 quarts 4.26 liters cooling system * mopar t antifreeze/coolant 5 year/100,000 miles formula), or equivalent. 7.2 quarts 6.8 liters *...

  • Page 390

    Component fluids, lubricants and genuine parts engine oil filter mopar t 04884900ab or equivalent. Spark plugs refer to the vehicle emission control information label in the engine com- partment. Fuel selection 87 octane (r + m)/2 chassis component fluids, lubricants and genuine parts. Automatic tra...

  • Page 392: Maintenance Schedules

    Maintenance schedules contents m emission control system maintenance . . . . . . . . 392 m maintenance schedules . . . . . . . . . . . . . . . . . . . 392 ▫ schedule “b” . . . . . . . . . . . . . . . . . . . . . . . . 395 ▫ schedule “a” . . . . . . . . . . . . . . . . . . . . . . . . 405 8 m a i n t...

  • Page 393

    Emission control system maintenance the “scheduled” maintenance services, listed in bold type must be done at the times or mileages specified to assure the continued proper functioning of the emission control system. These, and all other maintenance services included in this manual, should be done t...

  • Page 394

    • off-road or desert operation. • heavy loading note: if any of these apply to you then change your engine oil every 3,000 miles (5 000 km) or 3 months, whichever comes first and follow schedule “b” of the 9maintenance schedules9 section of this manual. Note: if any of these apply to you then change...

  • Page 395

    Once a month • check tire pressure and look for unusual wear or damage. • inspect the battery and clean and tighten the terminals as required. • check the fluid levels of coolant reservoir, brake/ clutch master cylinder, and manual transaxle and add as needed. • check all lights and all other electr...

  • Page 396

    Schedule “b” follow schedule “b” if you usually operate your vehicle under one or more of the following conditions. • day or night temperatures are below 32 °f (0 °c). • stop and go driving. • extensive engine idling. • driving in dusty conditions. • short trips of less than 10 miles (16 km). • more...

  • Page 397

    Miles 3,000 6,000 9,000 12,000 15,000 (kilometers) (5 000) (10 000) (15 000) (20 000) (25 000) change engine oil and engine oil filter, or at 3 months whichever comes first. X x x x x rotate tires. X x check spare tire for proper pressure and correct stowage. X x inspect engine air cleaner filter, r...

  • Page 398

    Miles 18,000 21,000 24,000 27,000 30,000 (kilometers) (30 000) (35 000) (40 000) (45 000) (50 000) change engine oil and engine oil filter, or at 3 months whichever comes first. X x x x x rotate tires. X x x check spare tire for proper pressure and correct stowage. X x x inspect brake linings. X rep...

  • Page 399

    Miles 33,000 36,000 39, 000 42,000 45,000 (kilometers) (55 000) (60 000) (65 000) (70 000) (75 000) change engine oil and engine oil filter, or at 3 months whichever comes first. X x x x x rotate tires. X x check spare tire for proper pressure and correct stowage. X x inspect brake linings. X inspec...

  • Page 400

    Miles 48,000 51,000 54,000 57,000 60,000 (kilometers) (80 000) (85 000) (90 000) (95 000) (100 000) change engine oil and engine oil filter, or at 3 months whichever comes first. X x x x x change automatic transaxle (cvt) fluid and filter x change manual transaxle fluid. X change rear drive assembly...

  • Page 401

    Miles 63,000 66,000 69,000 72,000 75,000 (kilometers) (105 000) (110 000) (115 000) (120 000) (125 000) change engine oil and engine oil filter, or at 3 months whichever comes first. X x x x x rotate tires. X x check spare tire for proper pressure and correct stowage. X x inspect brake linings. X in...

  • Page 402

    Miles 78,000 81,000 84,000 87,000 90,000 (kilometers) (130 000) (135 000) (140 000) (145 000) (150 000) change engine oil and engine oil filter, or at 3 months whichever comes first. X x x x x rotate tires. X x x check spare tire for proper pressure and correct stowage. X x x inspect brake linings. ...

  • Page 403

    Miles 93,000 96,000 99,000 102,000 (kilometers) (155 000) (160 000) (165 000) (170 000) change engine oil and engine oil filter, or at 3 months whichever comes first. X x x x change manual transaxle fluid. X rotate tires. X x check spare tire for proper pressure and correct stowage. X x flush and re...

  • Page 404

    Miles 105,000 108,000 111,000 114,000 117,000 120,000 (kilometers) (175 000) (180 000) (185 000) (190 000) (195 000) (200 000) change engine oil and engine oil filter, or at 3 months whichever comes first. X x x x x x change automatic transaxle (cvt) fluid and filter x change rear drive assembly (rd...

  • Page 405

    Miles 105,000 108,000 111,000 114,000 117,000 120,000 (kilometers) (175 000) (180 000) (185 000) (190 000) (195 000) (200 000) replace climate control air filtration filter (if equipped). X x ** this maintenance is recommended by the manufac- turer to the owner, but not required to maintain the emis...

  • Page 406

    Schedule “a” miles 6,000 12,000 18,000 24,000 30,000 (kilometers) (10 000) (20 000) (30 000) (40 000 ) (50 000) [months] [6] [12] [18] [24] [30] change engine oil and engine oil filter. X x x x x rotate tires. X x x x x check spare tire for proper pressure and correct stowage. X x x x x inspect brak...

  • Page 407

    Miles 36,000 42,000 48,000 54000 60,000 66,000 (kilometers) (60 000) (70 000) (80 000) (90 000) (100 000) (110 000) [months] [36] [42] [48] [54] [60] [66] change engine oil and engine oil filter. X x x x x x change rear drive assembly (rda) fluid. X change power transfer unit (ptu) fluid. X rotate t...

  • Page 408

    Miles 72,000 78,000 84,000 90,000 96,000 (kilometers) (120 000) (130 000) (140 000) (150 000) (160 000) [months] [72] [78] [84] [90] [96] change engine oil and engine oil filter. X x x x x rotate tires. X x x x x check spare tire for proper pressure and correct stowage. X x x x x inspect brake linin...

  • Page 409

    Miles 102,000 108,000 114,000 120,000 (kilometers) (170 000) (180 000) (190 000) (200 000) [months] [102] [108] [114] [120] change engine oil and engine oil filter. X x x x change rear drive assembly (rda) fluid. X change power transfer unit (ptu) fluid. X rotate tires. X x x x check spare tire for ...

  • Page 410

    ** this maintenance is recommended by the manufac- turer to the owner, but not required to maintain the emissions warranty. Inspection and service should also be performed anytime a malfunction is observed or suspected. Retain all re- ceipts. Warning! You can be badly injured working on or around a ...

  • Page 412: Contents

    If you need consumer assistance contents m suggestions for obtaining service for your vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . 412 ▫ prepare for the appointment . . . . . . . . . . . . 412 ▫ prepare a list . . . . . . . . . . . . . . . . . . . . . . . . 412 ▫ be reasonable with re...

  • Page 413

    Suggestions for obtaining service for your vehicle prepare for the appointment if you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty, discuss additional charges with the service manager. ...

  • Page 414

    Technicians, special tools, and the latest information to assure your vehicle is fixed correctly and in a timely manner. This is why you should always talk to your dealer’s service manager first. Most matters can be resolved with this process. • if for some reason you are still not satisfied, talk t...

  • Page 415

    Customer assistance for the hearing or speech impaired (tdd/tty) to assist customers who have hearing difficulties, the manufacturer has installed special tdd (telecommuni- cation devices for the deaf) equipment at its customer center. Any hearing or speech impaired customer who has access to a tdd ...

  • Page 416

    Warning! Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the state of california to cause cancer and birth defects or other reproductive harm. In addition, certain fluids contained in vehicles and certain prod- ucts of component wear contai...

  • Page 417

    To contact nhtsa, you may either call the auto safety hotline toll free at 1–888–327–4236 (tty: 1–800–424– 9153), or go to http://www.Safercar.Gov; or write to: administrator, nhtsa, 400 seventh street, sw., wash- ington, dc 20590. You can also obtain other information about motor vehicle safety fro...

  • Page 418

    • diagnostic procedure manuals. Filled with diagrams, charts and detailed illustrations, these practical manuals make it easy for students and technicians to find and fix problems on computer- controlled vehicle systems and features. They show exactly how to find and correct problems the first time,...

  • Page 419

    All passenger car tires must conform to federal safety requirements in addition to these grades. Treadwear the treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled con- ditions on a specified government test course. For ex- ample, a tire graded 150 ...

  • Page 420

    Temperature grades the temperature grades are a (the highest), b, and c, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the materi...

  • Page 422: Index

    Index 10

  • Page 423

    Abs (anti-lock brake system) . . . . . . . . . . . . . . 273 adding engine coolant (antifreeze) . . . . . . . . . . 362 adding fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . 307 adding washer fluid . . . . . . . . . . . . . . . . . . 126,159 additives, fuel . . . . . . . . . . . . . . . ...

  • Page 424

    Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 354 keyless transmitter replacement (rke) . . . . . . . 29 belts, drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . 351 body mechanism lubrication . . . . . . . . . . . . . . . 358 b-pillar location . . . . . . . . . ....

  • Page 425

    Cd (compact disc) player maintenance . . . . . . . . 222 cellular phone . . . . . . . . . . . . . . . . . . . . . . . . 82,223 center high mounted stop light . . . . . . . . . . . . 387 chains, tire . . . . . . . . . . . . . . . . . . . . . . . . . . . . 301 changing a flat tire . . . . . . . . . . ...

  • Page 426

    Crankcase emission control system . . . . . . . . . . 353 cruise light . . . . . . . . . . . . . . . . . . . . . . . . . . . 174 cup holder . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151 customer assistance . . . . . . . . . . . . . . . . . . . . . 412 data recorder, event . . . . . . ....

  • Page 427

    Emergency, in case of jacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 326 jump starting . . . . . . . . . . . . . . . . . . . . . . . . . 331 towing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 336 emission control system maintenance . . . . . . 344,392 engine . . . . ...

  • Page 428

    Fluid level checks automatic transaxle . . . . . . . . . . . . . . . . . . . . 369 fluids . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 388 fluids, lubricants and genuine parts . . . . . . . . . . 388 fog lights . . . . . . . . . . . . . . . . . . . . . . . 121,177,383 folding rear...

  • Page 429

    Tachometer . . . . . . . . . . . . . . . . . . . . . . . . . . 171 gearshift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 242 general information . . . . . . . . . . . . . . . . . 16,107,301 general maintenance . . . . . . . . . . . . . . . . . . . . . 347 glass cleaning . . . . . . ....

  • Page 430

    Interior appearance care . . . . . . . . . . . . . . . . . . 374 intermittent wipers (delay wipers) . . . . . . . . . . . 125 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 jack location . . . . . . . . . . . . . . . . . . . . . . . . . . . 327 jack operation . . . . . . . ...

  • Page 431

    Headlight switch . . . . . . . . . . . . . . . . . . . . . . 119 headlights . . . . . . . . . . . . . . . . . . . . . . . . . . . 119 high beam indicator . . . . . . . . . . . . . . . . . . . . 170 instrument cluster . . . . . . . . . . . . . . . . . . . . . 119 license . . . . . . . . . . . . . . ....

  • Page 432

    Fluid level check . . . . . . . . . . . . . . . . . . . 370,371 frequency of fluid change . . . . . . . . . . . . 370,371 lubricant selection . . . . . . . . . . . . . . . 369,370,371 map/reading lights . . . . . . . . . . . . . . . . . . . . . 118 master cylinder (brakes) . . . . . . . . . . . . . ...

  • Page 433

    Opener, garage door (homelink t) . . . . . . . . . . . 130 operator manual (owner’s manual) . . . . . . . . . . . . 5 outside air intake . . . . . . . . . . . . . . . . . . . . . . . 230 overdrive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 243 overheating, engine . . . . . . . . . . ....

  • Page 434

    Radio, navigation . . . . . . . . . . . . . . . . . . . . . . . 213 radio operation . . . . . . . . . . . . . . . . . . . 191,199,223 radio, satellite . . . . . . . . . . . . . . . . . . . . . . . 213,217 radio (sound systems) . . . . . . . . . . . . . . . . . 191,199 rear axle (differential) . . . ...

  • Page 435

    Satellite radio antenna . . . . . . . . . . . . . . . . . . . 220 schedule, maintenance . . . . . . . . . . . . . . . . . . . . 392 seat belt maintenance . . . . . . . . . . . . . . . . . . . . 376 seat belt reminder . . . . . . . . . . . . . . . . . . . . . . . 47 seat belts . . . . . . . . . . . ....

  • Page 436

    Signals, turn . . . . . . . . . . . . . . . . . . . . . . . . . . . 384 slippery surfaces, driving on . . . . . . . . . . . . . . . 334 snow tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . 302 spare tire . . . . . . . . . . . . . . . . . . . . . . . 289,290,327 spark plugs . . . . . . ...

  • Page 437

    Tire and loading information placard . . . . . . . . . 281 tire identification number (tin) . . . . . . . . . . . . . 280 tire markings . . . . . . . . . . . . . . . . . . . . . . . . . . 277 tire safety information . . . . . . . . . . . . . . . . . . . . 277 tires . . . . . . . . . . . . . . . . . ...

  • Page 438

    Hitches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 312 minimum requirements . . . . . . . . . . . . . . . . . 315 trailer and tongue weight . . . . . . . . . . . . . . . . 314 wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 319 trailer towing guide . . . . . . . . ....

  • Page 439

    Vehicle theft alarm (security alarm) . . . . . . . . . . 30 warning lights (instrument cluster description) . 169 warnings and cautions . . . . . . . . . . . . . . . . . . . . . 7 warranty information . . . . . . . . . . . . . . . . . . . . . 415 washer, adding fluid . . . . . . . . . . . . . . . . ...

  • Page 440

    2007 owner’ s manual 2 0 0 7 p a t r io t 81-326-0712 first edition printed in u.S.A..