1. DL manuals
  2. Jeep
  3. Automobile
  4. 2008 Commander
  5. Owner's Manual

Jeep 2008 Commander Owner's Manual

Other manuals for 2008 Commander: Owner's Manual

Summary of 2008 Commander

  • Page 1

    Commander o w n e r ’ s m a n u a l 2 0 0 8 2 0 0 8 c o m m a n d e r 81-326-0810 first edition printed in u.S.A..

  • Page 2: Table Of Contents

    Table of contents section page 1 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 things to know before starting your vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 3 understanding the f...

  • Page 4: Introduction

    Introduction contents m introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 m rollover warning . . . . . . . . . . . . . . . . . . . . . . . . 5 m how to use this manual . . . . . . . . . . . . . . . . . . 6 m warnings and cautions . . . . . . . . . . . . . . . . . . . 8 m vehicle i...

  • Page 5

    Introduction this is a specialized utility vehicle designed for both on-road and off-road use. It can go places and perform tasks for which conventional two-wheel drive enclosed vehicles were not intended. It handles and maneuvers differently from many passenger cars both on-road and off-road, so ta...

  • Page 6

    Note: after you read the manual, it should be stored in the vehicle for convenient reference and remain with the vehicle when sold so that the new owner will be aware of all safety warnings. When it comes to service, remember that your authorized dealer knows your vehicle best, has the factory-train...

  • Page 7

    Failure to use driver and passenger seat belts provided is a major cause of severe or fatal injury. In fact, the u.S. Government notes that the universal use of existing seat belts could cut the highway death toll by 10,000 or more each year and could reduce disabling injuries by two million annuall...

  • Page 8

    Introduction 7 1.

  • Page 9

    Warnings and cautions this owner’s manual contains warnings against op- erating procedures that could result in an accident or bodily injury. It also contains cautions against proce- dures that could result in damage to your vehicle. If you do not read this entire manual, you may miss important info...

  • Page 10

    Vehicle modifications/alterations warning! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death. Introduction 9 1.

  • Page 12: Contents

    Things to know before starting your vehicle contents m a word about your keys . . . . . . . . . . . . . . . . . .14 ▫ wireless ignition node (win) . . . . . . . . . . . . .14 ▫ fob with integrated key (fobik) . . . . . . . . . .15 ▫ ignition key removal . . . . . . . . . . . . . . . . . . .16 ▫ key-...

  • Page 13

    ▫ programming additional transmitters . . . . . . . .25 ▫ transmitter battery service . . . . . . . . . . . . . . .25 ▫ general information . . . . . . . . . . . . . . . . . . . .26 m remote starting system — if equipped . . . . . . . .27 ▫ how to use remote start . . . . . . . . . . . . . . . .27 m...

  • Page 14

    ▫ driver and front passenger supplemental restraint systems (srs) . . . . . . . . . . . . . . . . . .50 ▫ child restraint . . . . . . . . . . . . . . . . . . . . . . . .61 m engine break-in recommendations . . . . . . . . . . .71 m safety tips . . . . . . . . . . . . . . . . . . . . . . . . . . . .7...

  • Page 15

    A word about your keys your vehicle uses a keyless ignition system. This system consists of a fob with integrated key (fobik) and a wireless ignition node (win) with integral ignition switch. You can insert the double-sided integrated key into the ignition switch with either side up. Wireless igniti...

  • Page 16

    Fob with integrated key (fobik) the fob with integrated key operates the ignition switch. It also contains the remote keyless entry (rke) trans- mitter and a valet key, which stores in the rear of the fob. The valet key allows for entry into the vehicle should the battery in the vehicle or the fob g...

  • Page 17

    Ignition key removal place the shift lever in park. Turn the key to the lock position, and remove the key. Note: • if you try to remove the key before you place the shift lever in park, it may become trapped temporarily in the ignition switch. If this occurs, rotate the key to the right slightly, th...

  • Page 18

    Caution! An unlocked car is an invitation to thieves. Always remove key from the ignition and lock all doors when leaving the vehicle unattended. Key-in-ignition reminder if you open the driver’s door and the key is in the ignition, a chime will sound to remind you to remove the key. Note: the key-i...

  • Page 19

    An invalid fob to start the engine. Either of these condi- tions will result in the engine being shut off after two seconds. If the vehicle security alarm indicator light turns on during normal vehicle operation (vehicle running for longer than 10 seconds), it indicates that there is a fault in the ...

  • Page 20

    Keep the pin in a secure location. This number is required for authorized dealer replacement of fobs. Du- plication of fobs may be performed at an authorized dealer or by using the customer key programming procedure. This procedure consists of programming a blank fob to the vehicle electronics. A bl...

  • Page 21

    Note: if a programmed key is lost, see your authorized dealer to have all remaining keys erased from the sys- tem’s memory. This will prevent the lost key from starting your vehicle. The remaining keys must then be reprogrammed. All vehicle keys must be taken to an authorized dealer at the time of s...

  • Page 22

    To set the alarm the alarm will set when you use the remote keyless entry (rke) transmitter to lock the doors and liftgate, or when you use the power door lock switch while the door is open. After all the doors are locked and closed, the sentry key t/security alarm indicator light (located in the in...

  • Page 23

    Remote keyless entry this system allows you to lock or unlock the doors and liftgate, or activate the panic alarm, from distances up to about 23 ft (7 m) using a hand-held rke radio transmit- ter. The rke transmitter does not need not be pointed at the vehicle to activate the system. Note: inserting...

  • Page 24

    Remote key unlock, driver door/all doors first this feature lets you program the system to unlock either the driver’s door, or all doors, on the first press of the unlock button on the rke transmitter. To change the current setting, proceed as follows: • for vehicles equipped with the electronic veh...

  • Page 25

    To lock the doors press and release the lock button on the rke transmit- ter to lock all doors. The turn signal lights will flash and the horn will chirp to acknowledge the signal. Sound horn with remote key lock this feature will cause the horn to chirp when the doors are locked with the rke transm...

  • Page 26

    The panic alarm will stay on for three minutes unless you turn it off by either pressing the panic button a second time, or drive the vehicle at a speed of 15 mph (24 km/h) or greater. Note: • the interior lights will turn off if you turn the ignition switch to the acc or on position while the panic...

  • Page 27

    1. Battery access is through a door located on the rear of the fobik. Insert a small, flat-bladed screwdriver into the slot and gently pry open the access door. 2. Remove and replace the batteries. Avoid touching the new batteries with your fingers. Skin oils may cause battery deterioration. If you ...

  • Page 28

    Note: changes or modifications not expressly ap- proved by the party responsible for compliance could void the user’s authority to operate the equipment. If your remote keyless entry (rke) transmitter fails to operate from a normal distance, check for these two conditions. 1. A weak battery in the t...

  • Page 29

    To enter remote start mode press and release the remote start button on the rke transmitter twice, within five sec- onds. The parking lights will flash and the horn will honk twice (if programmed). Then, the engine will start and the vehicle will remain in the remote start mode for a 15 minute cycle...

  • Page 30

    You turn the key to run. Refer to “electronic vehicle information center” in section 4 of this manual. To turn off the engine while in remote start mode press and release the remote start button one time. Note: to avoid inadvertent shut downs, the system will disable the one time press of the remote...

  • Page 31

    Power door locks the power door lock switch is located on each front door panel. Press the switch to lock or unlock the doors. If the plunger is down when the door is closed, the door will lock. Therefore, make sure the key is not inside the vehicle before closing the door. If you press the door loc...

  • Page 32

    Automatic unlock on exit feature — only available if auto lock is enabled this feature will unlock all the doors when the driver’s door is opened if the vehicle is stopped and in park or neutral. Refer to “electronic vehicle information cen- ter (evic) — customer programmable features” in section 4 ...

  • Page 33

    Windows power windows the power window controls are located on the driver’s door trim panel. There is a single switch on the front passenger door/rear doors which operate the front passenger/rear passenger door windows. The window controls will operate only when the ignition switch is in the on or a...

  • Page 34

    The first detent, release, and the window will go down automatically. To cancel the “auto down” movement, operate the switch in either the up or down direction and release the switch. To stop the window from going all the way down during the auto-down operation, pull up on the switch briefly. To ope...

  • Page 35

    Resetting the auto-up feature should the auto-up feature stop working, the window probably needs to be reset. To reset auto-up: pull the window switch up and close the window com- pletely, then pull and hold the switch for one second. Window lockout switch the window lockout switch on the driver’s d...

  • Page 36

    Wind buffeting wind buffeting can be described as the perception of pressure on the ears or a helicopter type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions. This is a normal occur- rence and ...

  • Page 37

    Liftgate flipper glass the liftgate flipper glass is also unlocked when the liftgate is unlocked. To open the flipper glass, push up on the window switch located on the liftgate. Warning! To avoid injury stand back when opening. Glass will automatically rise. Once the liftgate flipper glass has been...

  • Page 38

    Power liftgate — if equipped the power liftgate may be opened manually or by pressing the liftgate button on the fob with integrated key (fobik). Press the liftgate button on the fob with integrated key (fobik) twice within five seconds, to open the power liftgate. Once the liftgate is fully open, p...

  • Page 39

    Feature is enabled, the turn signals will flash twice to signal that the liftgate is opening or closing. Note: • in the event of a power malfunction to the liftgate, an emergency liftgate latch release can be used to open the liftgate. The emergency liftgate latch release can be accessed through a s...

  • Page 40

    • if the liftgate handle is pulled while the power liftgate is opening, the liftgate motor will disengage to allow manual operation. • the power liftgate buttons will not operate if the vehicle is in gear or the vehicle speed is above 0 mph (0 km/h). • the power liftgate will not operate in temperat...

  • Page 41

    Gas props support the liftgate in the open position. However, because the gas pressure drops with tempera- ture, it may be necessary to assist the props when opening the liftgate in cold weather. Occupant restraints some of the most important safety features in your vehicle are the restraint systems...

  • Page 42

    Research has shown that seat belts save lives, and they can reduce the seriousness of injuries in a collision. Some of the worst injuries happen when people are thrown from the vehicle. Seat belts reduce the possibility of ejection and the risk of injury caused by striking the inside of the vehicle....

  • Page 43

    Lap/shoulder belt operating instructions 1. Enter the vehicle and close the door. Sit back and adjust the seat. 2. The seat belt latch plate is above the back of your seat. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to make the belt go aroun...

  • Page 44

    3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” warning! A belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt ...

  • Page 45

    4. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap portion, pull up a bit on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision. Wa...

  • Page 46

    6. To release the belt, push the red button marked press on the buckle. The belt will automatically retract to its stowed position. If necessary, slide the latch plate down the webbing to allow it to retract fully. Warning! A frayed or torn belt could rip apart in a collision and leave you with no p...

  • Page 47

    As a guide, if you are shorter than average, you will prefer a lower position, and if you are taller than average, you’ll prefer a higher position. When you release the anchorage, try to move it up or down to make sure that it is locked in position. Automatic locking mode — if equipped in this mode,...

  • Page 48

    This safety belt system has a retractor assembly that is designed to release webbing in a controlled manner. This feature is designed to help reduce the belt force acting on the occupant’s chest. Warning! • the belt and retractor assembly must be replaced if the seat belt assembly “automatic locking...

  • Page 49

    Enhanced seat belt use reminder system (beltalert t ) if the driver’s seat belt has not been buckled within 60 seconds of starting the vehicle and if the vehicle speed is greater than 5 mph (8 km/h), the enhanced warning system (beltalert t) will alert the driver to buckle their seat belt. The drive...

  • Page 50

    The enhanced warning system (beltalert t) can be reac- tivated by repeating this procedure. Note: although the enhanced warning system (beltalert t) has been deactivated, the seat belt warning light will continue to illuminate while the driver’s seat belt remains unfastened. Seat belts and pregnant ...

  • Page 51

    Driver and front passenger supplemental restraint systems (srs) this vehicle has airbags for both the driver and right front passenger as a supplement to the seat belt restraint systems. The driver’s front airbag is mounted in the steering wheel. The passenger side airbag is mounted in the instrumen...

  • Page 52

    Note: airbag covers may not be obvious in the interior trim; but they will open to allow airbag deployment. Warning! • do not put anything on or around the front airbag covers or attempt to manually open them. You may damage the airbags and you could be injured because the airbags are no longer func...

  • Page 53

    Note: do not use a clothing bar mounted to the coat hooks in this vehicle. A clothing bar will impede the proper performance of the window bags. The front airbags have a multistage inflator design. This allows the airbag to have different rates of inflation that are based on collision severity. Alon...

  • Page 54

    Seat as far back as possible, and use the proper child restraint. Refer to “child restraint” in this section. You should read the instructions provided with your child restraint to make sure that you are using it properly. 2. All occupants should use their lap and shoulder belts properly. 3. The dri...

  • Page 55

    Airbag system components the airbag system consists of the following: • occupant restraint control module • airbag warning light • driver airbag • passenger airbag • side curtain airbags above side windows • side remote acceleration sensors • driver side seat track position sensor • steering wheel a...

  • Page 56

    Also, the orc turns on the airbag warning light for 2.5 to 8 seconds for a self-check when the ignition is first turned on. After the self-check, the airbag warning light will turn off. If the orc detects a malfunction in any part of the system, it turns on the airbag warning light either momentaril...

  • Page 57

    • the side impact srs side curtain airbags are de- signed to activate only in certain side or rollover collisions. When the occupant restraint control mod- ule (orc) detects a collision requiring the window bags to inflate, it signals the inflators on the crash side of the vehicle, and both sides of...

  • Page 58

    If you do have a collision which deploys the airbags, any or all of the following may occur: • the nylon airbag material may sometimes cause abra- sions and/or skin reddening to the driver and front passenger as the airbags deploy and unfold. The abrasions are similar to friction rope burns or those...

  • Page 59

    Enhanced accident response feature if the airbags deploy after an impact and the electrical system remains functional, vehicles equipped with power door locks will unlock automatically. The hazard lights will flash and the fuel will be cut off to the engine. In addition, after the vehicle has stoppe...

  • Page 60

    Note: perchlorate material – special handling may apply, see www.Dtsc.Ca.Gov/hazardouswaste/perchlorate airbag warning light you will want to have the airbag system ready to inflate for your protection in an impact. The airbag system is designed to be maintenance free. If any of the following occurs...

  • Page 61

    Injuries in order to assess and improve vehicle perfor- mance. In addition to crash investigations initiated by daimlerchrysler corporation, such investigations may be requested by customers, insurance carriers, govern- ment officials, and professional crash researchers, such as those associated wit...

  • Page 62

    Data parameters that may be recorded: • diagnostic trouble code(s) and warning lamp status for electronically-controlled safety systems, including the airbag system • airbag disable lamp status (if equipped) • 9time9 of airbag deployment (in terms of ignition cycles and vehicle mileage) • airbag dep...

  • Page 63

    Seat owner’s manual to ensure you have the right seat for your child. Use the restraint that is correct for your child: warning! In a collision, an unrestrained child, even a tiny baby, can become a missile inside the vehicle. The force required to hold even an infant on your lap can become so great...

  • Page 64

    • rearward-facing child seats must never be used in the front seat of a vehicle with the front passenger airbag unless the airbag is turned off. An airbag deployment could cause severe injury or death to infants in this position. Warning! • improper installation can lead to failure of an infant or c...

  • Page 65

    Around the child restraint so that it is not necessary to use a locking clip. If the seat belt has a cinching latch plate, pulling up on the shoulder portion of the lap/shoulder belt will tighten the belt (the cinching latch plate will keep the belt tight, however, any seat belt system will loosen w...

  • Page 66

    Note: for additional information refer to www.Seatcheck.Org or call 1-866-seatcheck. Older children and child restraints children who weigh more than 20 lbs (9 kg) and who are older than one year can ride forward-facing in the vehicle. Forward-facing child seats and convertible child seats used in t...

  • Page 67

    Latch — child seat anchorage system (lower anchors and tether for children) your vehicle’s second row seat is equipped with the child restraint anchorage system called latch. The latch system provides for the installation of the child restraint without using the vehicle’s seat belts, instead securin...

  • Page 68

    If you are installing latch-compatible child restraints in adjacent rear seating positions, you can use the latch anchors or the vehicle’s seat belt for the outboard position, but you must use the vehicle’s seat belt at the center position. If your child seats are not latch- compatible, you can only...

  • Page 69

    In addition, there are tether strap anchorages behind each rear outboard seating position located on the back of the seat. Many, but not all restraint systems will be equipped with separate straps on each side, with each having a hook or connector for attachment to the lower anchorage and a means of...

  • Page 70

    Downward into the seat, removing slack in the straps according to the child restraint manufacturer’s instruc- tions. Warning! Improper installation of a child restraint to the latch anchorages can lead to failure of an infant or child restraint. The child could be badly injured or killed. Follow the...

  • Page 71

    In the rear seat, you may have trouble tightening the lap/shoulder belt on the child restraint because the buckle or latch plate is too close to the belt path opening on the restraint. Disconnect the latch plate from the buckle and twist the short buckle-end belt several times to shorten it. Insert ...

  • Page 72

    Warning! An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchor positions directly behind the child seat to secure a child restraint top tether strap. Transporting pets airbags deploying in the front seat could harm your pet. An...

  • Page 73

    A new engine may consume some oil during its first few thousand miles (kilometers) of operation. This should be considered as a normal part of the break-in and not interpreted as an indication of difficulty. Safety tips exhaust gas warning! Exhaust gases can injure or kill. They contain carbon monox...

  • Page 74

    Safety checks you should make inside the vehicle seat belts inspect the belt system periodically, checking for cuts, frays and loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Seat belt assemblies must be replaced after an accident if they have been d...

  • Page 75

    Lights have someone observe the operation of all exterior lights while you work the controls. Check turn signal and high beam indicator lights on the instrument panel. Fluid leaks check the area under the vehicle after overnight parking for fuel, coolant, oil or other fluid leaks. Also, if gasoline ...

  • Page 76: Contents

    Understanding the features of your vehicle contents m mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80 ▫ inside day/night mirror . . . . . . . . . . . . . . . . .80 ▫ automatic dimming mirror — if equipped . . . .80 ▫ outside mirrors . . . . . . . . . . . . . . . . . . . . . ....

  • Page 77

    M voice recognition system (vr) — if equipped . . 111 ▫ voice recognition system (vr) operation . . . . 111 ▫ commands . . . . . . . . . . . . . . . . . . . . . . . . . . 112 ▫ voice training . . . . . . . . . . . . . . . . . . . . . . . . 115 m seats . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Page 78

    ▫ smartbeams — if equipped . . . . . . . . . . . . . . 134 ▫ instrument panel and interior lights . . . . . . . 135 ▫ daytime running lights — if equipped . . . . . 135 ▫ lights-on reminder . . . . . . . . . . . . . . . . . . . 135 ▫ fog lights — if equipped . . . . . . . . . . . . . . . 136 ▫ turn ...

  • Page 79

    ▫ abs (anti-lock brake system) . . . . . . . . . . . . 147 ▫ tcs (traction control system) . . . . . . . . . . . . 148 ▫ bas (brake assist system) . . . . . . . . . . . . . . . 149 ▫ erm (electronic roll mitigation) . . . . . . . . . . 150 ▫ esp (electronic stability program) . . . . . . . . . 151 ▫...

  • Page 80

    ▫ security . . . . . . . . . . . . . . . . . . . . . . . . . . . . 172 ▫ troubleshooting tips . . . . . . . . . . . . . . . . . . . 173 ▫ general information . . . . . . . . . . . . . . . . . . . 173 m power sunroof — if equipped . . . . . . . . . . . . . 174 ▫ opening sunroof - express . . . . . . ...

  • Page 81

    Mirrors inside day/night mirror the mirror should be adjusted to center on the view through the rear window. A two-point pivot system allows for horizontal and vertical adjustment of the mirror. Annoying headlight glare from vehicles behind you can be reduced by moving the small control under the mi...

  • Page 82

    Caution! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror. Apply the solution onto a clean cloth and wipe the mirror clean. Outside mirrors to receive maximum benefit, adjust the outside mirrors to center on the adjacent lane of traffic with a...

  • Page 83

    Warning! Vehicles and other objects seen in the passenger side convex mirror will look smaller and farther away than they really are. Relying too much on your passenger side convex mirror could cause you to collide with another vehicle or other object. Use your inside mirror when judging the size or...

  • Page 84

    Power mirror preselected positions can be controlled by the optional memory seat feature. Refer to “driver memory seat” in this section for details. Heated remote control mirrors — if equipped these mirrors are heated to melt frost or ice. This feature is activated whenever you turn on the rear wind...

  • Page 85

    Lift the cover to reveal the mirror. The light will turn on automatically. Sun visor extension (if equipped) this feature has a pull out extension on the sun visor for increased coverage. Hands-free communication (uconnect t ) — if equipped note: the sales code rer radio contains an inte- grated han...

  • Page 86

    Note: for uconnect t customer support, visit the following websites: • www.Chrysler.Com/uconnect • www.Dodge.Com/uconnect • www.Jeep.Com/uconnect • or call 1–877–855–8400 uconnect t allows you to transfer calls between the system and your cellular phone as you enter or exit your vehicle and enables ...

  • Page 87

    Voice recognition button actual button location may vary with radio. The individual buttons are described in the “operation” section. The uconnect t system can be used with any hands-free profile certified bluetooth t cellular phone. See the uconnect t website for supported phones. If your cellu- la...

  • Page 88

    • for each feature explanation in this section, only the combined form of the voice command is given. You can also break the commands into parts and say each part of the command when you are asked for it. For example, you can use the combined form voice com- mand 9phonebook new entry,9 or you can br...

  • Page 89

    The following are general phone to uconnect t system pairing instructions: • press the phone button to begin. • after the 9ready9 prompt and the following beep, say 9setup phone pairing.9 • when prompted, after the beep, say 9pair a phone9 and follow the audible prompts. • you will be asked to say a...

  • Page 90

    • the system will prompt you to say the number you want to call. • for example, you can say 9234-567-8901.9 the phone number that you enter must be of valid length and combination. Based on the country in which the ve- hicle was purchased, the uconnect t system limits the user from dialing an invali...

  • Page 91

    • after the 9ready9 prompt and the following beep, say 9phonebook new entry.9 • when prompted, say the name of the new entry. Use of long names helps the voice recognition and it is recommended. For example, say 9robert smith9 or 9robert9 instead of 9bob.9 • when prompted, enter the number designati...

  • Page 92

    • some phones cannot send phonebook entries if they are already connected to any system via bluetooth t, and you may see a message on the phone display that the bluetooth t link is busy. In this case, the user must first disconnect or drop the bluetooth t connection to the uconnect t system, and the...

  • Page 93

    Delete entries in the uconnect t phonebook note: editing phonebook entries is recommended when the vehicle is not in motion. • press the phone button to begin. • after the 9ready9 prompt and the following beep, say 9phonebook delete.9 • after you enter the phonebook delete menu, you will then be ask...

  • Page 94

    List all names in the uconnect t phonebook • press the phone button to begin. • after the 9ready9 prompt and the following beep, say 9phonebook list names.9 • the uconnectt system will play the names of all the phonebook entries. • to call one of the names in the list, press the “voice recognition” ...

  • Page 95

    Answer or reject an incoming call - call currently in progress if a call is currently in progress and you have another incoming call, you will hear the same network tones for call waiting that you normally hear when using your cell phone. Press the phone button to place the current call on hold and ...

  • Page 96

    Three-way calling to initiate three-way calling, press the “voice recogni- tion” button while a call is in progress, and make a second phone call, as described under 9making a second call while current call in progress. 9 after the second call has established, press and hold the phone button until y...

  • Page 97

    • after the ignition key is switched to off, a call can continue on the uconnect t system for a certain dura- tion, after which the call is automatically transferred from the uconnect t system to the mobile phone. • an active call is automatically transferred to the mobile phone after the ignition k...

  • Page 98

    • after the 9ready9 prompt and the following beep, say 9emergency9 and the uconnectt system will instruct the paired cellular phone to call the emergency num- ber. This feature is only supported in the u.S. Note: the emergency number dialed is based on the country where the vehicle is purchased (911...

  • Page 99

    Certain companies, which time out a little too soon to work properly with the uconnect t system. Voice mail calling to learn how to access your voice mail, refer to 9working with automated systems. 9 working with automated systems this method is used in instances where one generally has to press num...

  • Page 100

    Note: • you may not hear all of the tones due to cellular phone network configurations; this is normal. • some paging and voice mail systems have system time out settings that are too short and may not allow the use of this feature. Barge in - overriding prompts the “voice recognition” button can be...

  • Page 101

    Dialing a number with your paired bluetooth t cellular phone, the audio will be played through your vehicle’s audio system. The uconnect t system will work the same as if you dial the number using voice recognition. Note: certain brands of mobile phones do not send the dial ring to the uconnect t sy...

  • Page 102

    Connect or disconnect link between the uconnect t system and cellular phone your cellular phone can be paired with many different electronic devices, but can only be actively 9connected9 with one electronic device at a time. If you would like to connect or disconnect the bluetooth t connection betwe...

  • Page 103

    Uconnect t system will return to using the highest priority phone present in or near (approximately within 30 ft [9 m]) the vehicle. Delete uconnect t paired cellular phones • press the phone button to begin. • after the 9ready9 prompt and the following beep, say 9setup phone pairing.9 • at the next...

  • Page 104

    Repeat the words and phrases when prompted by the uconnect t system. For best results, the voice training session should be completed when the vehicle is parked with the engine running, all windows closed, and the blower fan switched off. This procedure may be repeated with a new user. The system wi...

  • Page 105

    • when navigating through an automated system such as voice mail, or when sending a page, at the end of speaking the digit string, make sure to say 9send.9 • storing names in the phonebook when the vehicle is not in motion is recommended. • it is not recommended to store similar sounding names in th...

  • Page 106

    • performance, such as audio clarity, echo, and loudness to a large degree rely on the phone and network, and not the uconnect t system. • echo at the far end can sometimes be reduced by lowering the in-vehicle audio volume. • in a convertible vehicle, system performance may be compromised with the ...

  • Page 107

    106 understanding the features of your vehicle.

  • Page 108

    Understanding the features of your vehicle 107 3.

  • Page 109

    108 understanding the features of your vehicle.

  • Page 110

    Voice commands primary alternate(s) zero one two three four five six seven eight nine star (*) plus (+) pound (#) add location all voice commands primary alternate(s) call cancel confirmation prompts continue delete dial download edit emergency english erase all espanol francais help home understand...

  • Page 111

    Voice commands primary alternate(s) language list names list phones mobile mute mute off new entry no pager pair a phone phone pairing pairing phonebook phone book previous record again redial voice commands primary alternate(s) return to main menu return or main menu select phone select send set up...

  • Page 112

    General information this device complies with part 15 of the fcc rules and rss 210 of industry canada. Operation is subject to the following conditions: • this device may not cause harmful interference. • this device must accept any interference received, including interference that may cause undesi...

  • Page 113

    If you ever wish to interrupt the system while it lists options, press the vr hard-key, listen for the beep, and say your command. Pressing the vr hard-key while the system is speaking is known as “barging in.” the system will be interrupted and you can add or change commands. This will become helpf...

  • Page 114

    3. Use the on/off volume rotary knob to adjust the volume to a comfortable level while the voice recognition system is speaking. Please note the volume setting for vr is different then the audio system. Main menu start a dialogue by pressing the vr hard-key. You may say main menu to switch to the ma...

  • Page 115

    Satellite radio to switch to satellite radio mode say sat or satellite radio. In this mode, you may say the following com- mands: • channel number (to change the channel by its spoken number) • next channel (to select the next channel) • previous channel (to select the previous chan- nel) • list cha...

  • Page 116

    − continue (to continue recording) − delete (to delete the recording) • play memos (to play previously recorded memos) — during the playback you may press the vr hard- key to stop playing memos. You continue by saying one of the following commands: − repeat (to repeat a memo) − next (to play the nex...

  • Page 117

    Seats front manual seat adjustment move the seat forward or rearward using the adjustment bar. Lift up on the bar located on the front of the seat near the floor. Position the seat and be sure the latch engages fully. Warning! Adjusting a seat while the vehicle is moving is dangerous. The sudden mov...

  • Page 118

    Warning! • it is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seri- ously injured or killed. • do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • ...

  • Page 119

    4–way passenger’s power seat — if equipped the front passenger’s power seat switches are located on the outboard side of the passenger seat lower side trim. The bottom switch controls forward/rearward adjust- ment. The top switch controls the seatback recline adjust- ment. Note: the 4–way seat does ...

  • Page 120

    Front heated seats — if equipped heated seats provide comfort and warmth on cold days and can help soothe sore muscles and backs. The heaters provide the same heat level for both cushion and back. The front driver and passenger seats are heated. The controls for each heater are located near the bott...

  • Page 121

    Warning! Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaus- tion or other physical condition must exercise care when using the seat heater. It may cause burns even at low temperatures, especially if...

  • Page 122

    2. Fold the seatback down, and tumble the seat forward. Warning! Do not drive the vehicle with the outer second row seats in the tumbled position. The outer second row seats are only intended to be tumbled for entry and exit to the third row seat. Failure to follow these instructions could result in...

  • Page 123

    Note: if sitting in the third row seat, pull rearward on the release strap located at the rear of the seat and tumble the seat forward. Fold and tumble seat release strap 122 understanding the features of your vehicle.

  • Page 124

    Folding middle seatback (second row seat) 1. Pull the release strap. 2. Lower the center seatback. Release strap folding center seatback understanding the features of your vehicle 123 3.

  • Page 125

    Center seat armrest (second row seat) — if equipped the second row center seat may be equipped with a armrest. Pull strap to lower armrest. 50/50 third row folding seat — if equipped to lower rear seat either side of the third row seat can be lowered to allow for extended cargo space, and still main...

  • Page 126

    3. Close the tailgate. To raise rear seat 1. Open the tailgate. 2. Detach pull strap from back of seat, and pull seatback upward until it locks into place. Reattach strap. 3. Close the tailgate. Seatback release handle pull strap understanding the features of your vehicle 125 3.

  • Page 127

    Warning! The cargo area in the rear of the vehicle (with the rear seatbacks in the locked-up or folded down position) should not be used as a play area by children when the vehicle is in motion. They could be seriously injured in an accident. Children should be seated and using the proper restraint ...

  • Page 128

    Setting memory positions and linking remote keyless entry transmitter to memory note: each time the s (set) button and a numbered button 1 or 2 are pressed, you erase the memory settings for that button and store a new one. 1. Insert the ignition key, and turn the ignition switch to the on position....

  • Page 129

    11. Select 9remote linked to memory9 in the electronic vehicle information center (evic) and enter 9yes9 or select 9use factory settings9 from the evic and enter 9yes9. Refer to “electronic vehicle information center (evic) — customer programmable features” in section 4 for more information. 12. Rep...

  • Page 130

    To disable a transmitter linked to memory 1. Turn the ignition switch to the lock position, and remove the key. 2. Press and release memory button number 1. The system will recall any memory settings stored in position 1. Wait for the system to complete the memory recall before continuing to step 3....

  • Page 131

    • the seat will move to the position located 0.3 in (8 mm) forward of the rear stop if the starting position is between 0.9 to 2.67 in (23 to 68 mm) forward of the rear stop when the key is removed from the ignition switch. The seat will move forward to the memory/ driving position when the key is p...

  • Page 132

    To open and close the hood to open the hood, pull the release lever inside your vehicle located below the instrument panel and in front of the driver’s door. Then, reach under the hood, move safety latch to the left, and lift the hood. To prevent possible damage, do not slam the hood to close it. Us...

  • Page 133

    Warning! If the hood is not fully latched, it could fly up when the vehicle is moving and block your forward vision. Be sure all hood latches are fully latched before driving. Lights multifunction control lever the multifunction control lever controls the operation of the headlights, turn signals, h...

  • Page 134

    Headlights and parking lights turn the end of the multifunction control lever to the first detent for parking light operation. Turn to the second detent for headlight operation. Turn to the third detent for “auto” headlight operation (if equipped). Automatic headlight system — if equipped turn the e...

  • Page 135

    Approximately four minutes after the wipers completely stop. Refer to “windshield wipers and washers” in this section for more information. Note: when your headlights come on during the daytime, the instrument panel lights will automatically dim to the lower nighttime intensity. Refer to “instru- me...

  • Page 136

    Note: broken, muddy, or obstructed headlights and taillights of vehicles in the field of view will cause headlights to remain on longer (closer to the vehicle). Also, dirt, film, and other obstructions (sticker, toll box, etc.) on the windshield or camera lens will cause the system to function impro...

  • Page 137

    Fog lights — if equipped the fog light switch is located in the multifunction control lever. To activate the fog lights, turn on the park/turn lights, low beam headlights, or “auto” headlights and pull out the end of the multifunction control lever. A light in the instrument cluster shows when the f...

  • Page 138

    Passing light you can signal another vehicle with your headlights by lightly pulling the multifunction control lever toward the steering wheel. This will cause the headlights to turn on at high beam and remain on until the lever is released. Headlight time delay there is also a feature that delays t...

  • Page 139

    Courtesy/reading lights each light can be turned on by pressing the recessed area of the lens. To turn these lights off, press the recessed area of the lens a second time. There are also reading lights located above the rear doors. Each light can be turned on by pressing the front recessed area of t...

  • Page 140

    Windshield wipers and washers the front and rear wipers and washers are operated by a switch in the right side control lever. Turn the end of the control lever to select “lo,” “hi,” or one of the five speed sensitive intermittent windshield wiper speeds. Refer to “speed sensitive intermittent wiper ...

  • Page 141

    To use the washer, pull the lever toward you and hold while spray is desired. If the lever is pulled while in the delay range, the wiper will operate for several seconds after the lever is released, and then resume the intermit- tent interval previously selected. If the lever is pulled while in the ...

  • Page 142

    Rain sensing wipers—if equipped this feature senses moisture on the windshield and automatically activates the wipers for the driver. The feature is especially useful for road splash or overspray from the windshield washers of the vehicle ahead. Rotate the end of the multifunction lever to one of fi...

  • Page 143

    Operate until the wiper switch is moved, vehicle speed is greater than 0 mph (0 km/h), or the outside tem- perature is greater than 32°f (0°c). • transmission in neutral position — when the ignition is on, and the transmission is in the neu- tral position, the rain sensing system will not oper- ate ...

  • Page 144

    The steering wheel outward or push it inward as desired. To lock the steering column in position, push the control handle upward until fully engaged. Warning! Do not adjust the steering wheel while driving. The telescoping adjustment must be locked while driv- ing. Adjusting the steering wheel while...

  • Page 145

    Press the top of the switch to move the pedals forward (away from the driver). • the pedals can be adjusted with the ignition off. • the pedals can be adjusted while driving. • the pedals cannot be adjusted when the vehicle is in reverse (r) or when the speed control is on. A message will be display...

  • Page 146

    To activate push the on/off button. The cruise indicator light in the instrument cluster will illuminate. To turn the system off, push the on/off button a second time. The cruise indicator light will turn off. The system should be turned off when not in use. Warning! Leaving the speed control system...

  • Page 147

    To deactivate a soft tap on the brake pedal, pulling the speed control lever towards you, or normal brake pressure while slowing the vehicle will deactivate speed control without erasing the set speed memory. Pressing the on/off button or turning off the ignition switch erases the set speed memory. ...

  • Page 148

    To accelerate for passing depress the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed. Using speed control on hills the automatic transmission may downshift on hills to maintain the vehicle set speed. Note: the speed control system maintains sp...

  • Page 149

    Help avoid skidding on slippery surfaces during braking. Refer to “anti-lock brake system” in section 5 of this manual. Warning! Abs (anti-lock brake system) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions...

  • Page 150

    Bas (brake assist system) the bas is designed to optimize the vehicle’s braking capability during emergency braking maneuvers. The system detects an emergency braking situation by sens- ing the rate and amount of brake application and then applies optimum pressure to the brakes. This can help reduce...

  • Page 151

    Erm (electronic roll mitigation) this system anticipates the potential for wheel lift by monitoring the driver’s steering wheel input and the speed of the vehicle. When erm determines that the rate of change of the steering wheel angle and vehicle speed are sufficient to potentially cause wheel lift...

  • Page 152

    Esp (electronic stability program) this system enhances directional control and stability of the vehicle under various driving conditions. Esp cor- rects for oversteering or understeering of the vehicle by applying the brake of the appropriate wheel to assist in counteracting the oversteer or unders...

  • Page 153

    Warning! Esp (electronic stability program) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions. Esp cannot prevent accidents, in- cluding those resulting from excessive speed in turns, driving on very slipper...

  • Page 154

    Conditions and more wheel spin than esp would nor- mally allow is required to gain traction. To turn esp on again, momentarily depress the esp off switch. This will restore the normal “esp on” mode of operation. Note: to improve the vehicle’s traction when driving with snow chains, or starting off i...

  • Page 155

    In this mode, esp and tcs, except for the “limited slip” feature described in the tcs section, are turned off until the vehicle reaches a speed of 40 mph (64 km/h). At 40 mph (64 km/h), the system returns to “partial off” mode, described above. When the vehicle speed drops below 35 mph (56 km/h), th...

  • Page 156

    Vehicle reaches a speed of 40 mph (64 km/h). At 40 mph (64 km/h), the normal esp stability function returns but tcs remains off. When the vehicle speed drops below 35 mph (56 km/h), the esp system shuts off. Esp is deacti- vated at low vehicle speeds in 4wd low range so that it will not interfere wi...

  • Page 157

    Swaying. Always use caution when towing a trailer and follow the trailer tongue weight recommendations. Refer to “trailer towing” in section 5 of this manual. When tsc is functioning, the esp/tcs indicator light will flash, the engine power may be reduced and you may feel the brakes being applied to...

  • Page 158

    • gear selection matches vehicle uphill direction (i.E., vehicle facing uphill is in forward gear; vehicle back- ing uphill is in reverse gear). Hsa will work in reverse and all forward gears when the activation criteria have been met. The system will not activate if the vehicle is placed in neutral...

  • Page 159

    Hsa off if you wish to turn off the hsa system, it can be done using the customer programmable features in the elec- tronic vehicle information center (evic). Refer to “elec- tronic vehicle information center (evic)” in section 4 of this manual. Hdc (hill descent control) (4wd models with nv245 two–...

  • Page 160

    And will only activate when the vehicle is descending a hill. It will usually not activate on level ground. The hdc speed may be adjusted by the driver to suit the driving conditions. The speed corresponds to the trans- mission gear selected. • 1st = 1 mph (1.6 km/h) • 2nd = 2.5 mph (4 km/h) • 3rd =...

  • Page 161

    Warning! Hdc is only intended to assist the driver in control- ling vehicle speed when descending hills. The driver must remain attentive to the driving conditions and is responsible for maintaining a safe vehicle speed. Esp/bas warning light and esp/tcs indicator light the malfunction indicator lam...

  • Page 162

    Rear park assist system— if equipped the rear park assist system provides visible and audible indications of the distance between the rear fascia and the detected obstacle when backing up. Refer to the warning section and note section for limitations of this system and recommendations. The rear park...

  • Page 163

    Rear park assist warning display the rear park assist warning display, located in the headliner near the flipper glass, provides both visible and audible warnings to indicate the distance between the rear fascia and the detected obstacle. When the ignition is turned to the on position, the warning d...

  • Page 164

    Warning display distances display led obstacle distance from: led color audible signal rear corners rear center 1st led 59 in (150 cm) yellow yes, half second 2nd led 51 in (130 cm) yellow none 3rd led 45 in (115 cm) yellow none 4th led 31.5 in (80 cm) 39 in (100 cm) yellow none 5th led 25.5 in (65 ...

  • Page 165

    Enable/disable the rear park assist system the rear park assist system can be enabled and disabled with a switch located on the upper switch bank of the instrument panel. When the switch is pressed to disable the system, the instrument cluster will display the “park assist dis- abled” message. Refer...

  • Page 166

    Cleaning the rear park assist system clean the rear park assist sensors with water, car wash soap and a soft cloth. Do not use rough or hard cloths. Do not scratch or poke the sensors. Otherwise, you could damage the sensors. Rear camera — if equipped vehicles with a navigation radio may be equipped...

  • Page 167

    2. Select on at the “rear camera” screen. Highlight done and press enter. The rear camera is now en- abled. 3. When the vehicle is shifted into reverse, the cau- tion screen will appear, followed by an image of the rear of the vehicle. 4. When the vehicle is shifted out of reverse, the rear camera m...

  • Page 168

    Garage door opener — if equipped homelink t replaces up to three remote controls (hand- held transmitters) that operate devices such as garage door openers, motorized gates, lighting, or home security systems. The homelink t unit operates off your vehicle’s battery. The homelink t buttons are locate...

  • Page 169

    Warning! Your motorized door or gate will open and close while you are training the universal transceiver. Do not train the transceiver if people or pets are in the path of the door or gate. Only use this transceiver with a garage door opener that has a “stop and reverse” feature as required by fede...

  • Page 170

    It is recommended that a new battery be placed in the hand-held transmitter of the device being programmed to homelink t for more efficient training and accurate transmission of the radio-frequency signal. Your vehicle should be parked outside of the garage while training. 1. Turn the ignition switc...

  • Page 171

    Note: after training a homelink t channel, if the garage door does not operate with homelink t and the garage door opener was manufactured after 1995, the garage door opener may have rolling code. If so, proceed to the heading “programming a rolling code system.” 5. Programming a rolling code system...

  • Page 172

    7. Return to the vehicle and press the programmed homelink t button twice (holding the button for two seconds each time). If the device is plugged in and activates, programming is complete. If the device does not activate, press the button a third time (for two seconds) to complete the training. If ...

  • Page 173

    Then proceed with step 4 under “programming homelink t” earlier in this section. Using homelink t to operate, simply press and release the programmed homelink t button. Activation will now occur for the trained device (i.E., garage door opener, gate operator, security system, entry door lock, home/o...

  • Page 174

    Troubleshooting tips if you are having trouble programming homelink t, here are some of the most common solutions: • replace the battery in the original transmitter. • press the learn button on the garage door opener to complete the training for rolling code. • did you unplug the device for training...

  • Page 175

    Power sunroof — if equipped the power sunroof switch is located on the overhead console. Warning! • never leave children in a vehicle with the keys in the ignition switch. Occupants, particularly unat- tended children, can become entrapped by the power sunroof while operating the power sunroof switc...

  • Page 176

    Opening sunroof - express press the switch rearward and release, and the sunroof will open automatically from any position. The sunroof will open fully, then stop automatically. This is called express open. During express open operation, any movement of the sunroof switch will stop the sunroof. Clos...

  • Page 177

    Sunshade operation the sunshade can be opened manually. However, the sunshade will open automatically as the sunroof opens. Note: the sunshade cannot be closed if the sunroof is open. Wind buffeting wind buffeting can be described as the perception of pressure on the ears or a helicopter type sound ...

  • Page 178

    Note: hold onto shade handle until shade is com- pletely open or closed. Power outlet front power outlet to the left and right of the convenience tray (lower center of instrument panel) is an outlet for electrically powered accessories. Pull lightly on the tab of the plastic cover to access the outl...

  • Page 179

    Rear power outlet — if equipped the rear power outlet (if equipped) is located in the left rear cargo area. All accessories connected to this outlet should be re- moved or turned off when the vehicle is not in use to protect the battery against discharge. Caution! Electrical outlet use with engine o...

  • Page 180

    Power inverter — if equipped there is a 115–volt, 150–watt inverter outlet located on the back of the center console to convert dc current to ac current. This outlet can be used to power small appliances and electronics. Press the power inverter switch (located on the upper switch bank) to turn the ...

  • Page 181

    The inverter status indicator turns on. The status indica- tor of the ac power inverter indicates whether the inverter is producing ac power. Note: due to built-in overload protection, the inverter will shut down if the power rating is exceeded. Warning! To avoid serious injury or death: • do not us...

  • Page 182

    Note: the cupholder insert is removable, from the console, for cleaning. It can be reinstalled with the larger cup depression towards the passenger seat, but the top surface will not be flush with the console surface. Cupholders (second row seat) the second row seat has two cupholders in the center ...

  • Page 183

    Cupholders (third row seat) the third row seat passengers have cupholders on the left and right rear trim panels. Cargo area features cargo load floor the panel in the load floor is reversible for added utility. One side is carpeted and the other side features a plastic lined tray which holds a vari...

  • Page 184

    Note: the cargo load floor latches should not be used as cargo tie-downs. 1. Flip up pull loop(s) so they are perpendicular (straight up) to the top surface of the tray. 2. Pull up on loop(s) and twist 90 degrees, so they are parallel to the slotted hole in tray. 3. Lift tray over loop(s), and repos...

  • Page 185

    5. Push loop(s) back down, so they are parallel to the top of the tray. Rear window features rear window wiper/washer a switch on the right side of the steering column controls operation of the rear wiper/washer function. Rotating the center of the switch up to the del (delay) position or the on pos...

  • Page 186

    The rear wiper switch or the ignition switch needs to be turned off and on to restart the rear wiper. Adding washer fluid the fluid reservoir for the windshield washers and the rear window washer is shared. It is located in the front of the engine compartment on the passenger side and should be chec...

  • Page 187

    If not equipped, your authorized dealer can order and install mopar t cross rails built specifically for this roof rack system or a number of aftermarket rails that are tailored to your life-style or activities. The optional cross rails have five specific locations iden- tified by a feature on both ...

  • Page 188

    Caution! • to prevent damage to the roof of your vehicle, do not carry any loads on the roof rack without cross rails installed. The load should be secured and placed on top of the cross rails, not directly on the roof. If it is necessary to place the load on the roof, place a blanket or some other ...

  • Page 190: Contents

    Understanding your instrument panel contents m instrument panel and controls . . . . . . . . . . . . . 193 m instrument cluster . . . . . . . . . . . . . . . . . . . . . . 194 m instrument cluster description . . . . . . . . . . . . . 195 m electronic vehicle information center (evic) . . . 203 ▫ el...

  • Page 191

    M sales code req — am/fm stereo radio and 6–disc cd/dvd changer (mp3/wma aux jack) . . . . . . . . . . . . . . . . . . 220 ▫ operating instructions - radio mode . . . . . . . 220 ▫ operation instructions - (disc mode for cd and mp3/wma audio play, dvd-video) . . . . 228 ▫ notes on playing mp3/wma fi...

  • Page 192

    M sales code rer — multimedia system — if equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . . 251 ▫ operating instructions — satellite radio . . . . . 252 ▫ operating instructions — hands-free communication (uconnect t) (if equipped) . . . 252 ▫ clock setting procedure . . . . . . . . ....

  • Page 193

    M remote sound system controls — if equipped . . 266 ▫ radio operation . . . . . . . . . . . . . . . . . . . . . . 266 ▫ cd player . . . . . . . . . . . . . . . . . . . . . . . . . . 267 m cd/dvd disc maintenance . . . . . . . . . . . . . . . 267 m radio operation and cellular phones . . . . . . . ....

  • Page 194

    Instrument panel and controls 1 — air outlet 5 — upper switch bank 9 — lower switch bank 2 — instrument cluster 6 — power outlet/cigar lighter 10 — climate controls 3 — radio 7 — storage bin 11 — ignition switch 4 — glove box 8 — power outlet 12 — storage bin understanding your instrument panel 193 ...

  • Page 195

    Instrument cluster 194 understanding your instrument panel.

  • Page 196

    Instrument cluster description 1. Speedometer indicates vehicle speed. 2. Brake warning light the brake warning light will come on when the ignition is first turned on, and stay on briefly as a bulb check. If the bulb does not come on during starting, have the bulb re- paired promptly. If the light ...

  • Page 197

    Engine start. If the bulb does not come on when turning the key from off to on, have the condition checked promptly. Certain conditions such as a loose or missing gas cap, poor fuel quality, etc. May illuminate the light after engine start. The vehicle should be serviced if the light stays on throug...

  • Page 198

    On when the ignition switch is turned to the on position, have the light inspected by an authorized dealer. 8. Tachometer indicates the engine speed in revolutions per minute (rpm). 9. Security alarm system indicator light — if equipped this light will flash rapidly for approximately 15 seconds when...

  • Page 199

    12. Tire pressure monitoring telltale light each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. (if your vehicle has tires of a differ...

  • Page 200

    Your vehicle has also been equipped with a tpms malfunction indicator to indicate when the system is not operating properly. The tpms malfunction indicator is combined with the low tire pressure telltale. When the system detects a malfunction, the telltale will flash for approximately one minute and...

  • Page 201

    13. Temperature gauge the temperature gauge shows engine coolant tempera- ture. Any reading within the normal range indicates that the engine cooling system is operating satisfactorily. The gauge pointer will likely indicate a higher tempera- ture when driving in hot weather, up mountain grades, or ...

  • Page 202

    16. Electronic stability program (esp) warning light/brake assist system (bas) warning light the esp/bas warning light in the instrument cluster comes on when the ignition switch is turned to the on position. The light should go out with the engine running. If the esp/bas warning light comes on cont...

  • Page 203

    Correct mileage that the vehicle has been driven. There- fore, if the odometer reading is changed during repair or replacement, be sure to keep a record of the reading before and after the service so that the correct mileage can be determined. 21. Transmission range indicator this display indicator ...

  • Page 204

    25. Voltage warning light this light monitors the electrical system voltage. The light should turn on momentarily as the engine is started. If the light stays on or turns on while driving, it indicates a problem with the charging system. Immediate service should be obtained. 26. Low fuel warning lig...

  • Page 205

    • vehicle information warning message displays • personal settings (customer programmable features) • compass display • outside temperature display • trip computer functions the system allows the driver to select information by pressing the following buttons mounted on the steering wheel: menu butto...

  • Page 206

    Electronic vehicle information center (evic) displays when the appropriate conditions exist, the electronic vehicle information center (evic) displays the following messages: • turn signal on • perform service • key not programmed — damaged key • key not programmed — invalid key • key not programmed...

  • Page 207

    • hood/gate/door open (with graphic) • hood/gate/doors open (with graphic) • liftglass/door open (with graphic) • liftglass/doors open (with graphic) • liftglass/hood open (with graphic) • washer fluid low (with graphic) • coolant low (with graphic) • oil change required • oil change reset • check g...

  • Page 208

    • memory #2 positions set • memory system disabled — seatbelt buck- led (with graphic) • memory system disabled — vehicle not in park • driver 1 memory • driver 2 memory • adj. Pedals disabled — cruise control set • adj. Pedals disabled — shifter in reverse • tire low pressure • check tpm system • l...

  • Page 209

    Engine oil change indicator system oil change required your vehicle is equipped with an engine oil change indicator system. The “oil change required” message will flash in the evic display for approximately 10 seconds after a single chime has sounded to indicate the next scheduled oil change interva...

  • Page 210

    • service distance • display units of measure in press the scroll button to cycle through all the trip computer functions. The trip functions mode displays the following informa- tion: average fuel economy / fuel saver mode (5.7l engine only) shows the average fuel economy since the last reset. When...

  • Page 211

    This feature allows you to monitor when the mds switches off the fuel on four of the eight cylinders and it can be used to modify driving habits in order to increase the time in which the fuel saver mode is active. Distance to empty (dte) shows the estimated distance that can be traveled with the fu...

  • Page 212

    Trip a shows the total distance traveled for trip a since the last reset. Trip b shows the total distance traveled for trip b since the last reset. Elapsed time shows the total elapsed time of travel since the last reset when the ignition switch is in the acc position. Elapsed time will increment wh...

  • Page 213

    360° turns (in an area free from large metal or metallic objects) until the “cal” indicator displayed in the evic turns off. The compass will now function normally. Manual compass calibration if the compass appears erratic and the “cal” indicator does not appear in the evic display, you must put the...

  • Page 214

    1. Turn the ignition switch on. 2. Press and hold the compass/temperature but- ton for approximately two seconds. 3. Press the scroll button until the “compass vari- ance” message, and the last variance zone number dis- plays in the evic. 4. Press and release the function select button until the pro...

  • Page 215

    Press and release the menu button until personal set- tings displays in the evic. Use the scroll button to display one of the following choices: language when in this display you may select one of three lan- guages for all display nomenclature, including the trip functions and the navigation system ...

  • Page 216

    Entry unlock button twice to unlock the passenger’s doors. When “all doors 1st press” is selected, all of the doors will unlock on the first press of the remote keyless entry unlock button. To make your selection, press and release the function select button until “driver door 1st press” or “all doo...

  • Page 217

    Headlights on with wipers (available with auto headlights only) when yes (y) is selected, and the headlight switch is in the auto position, the headlights will turn on approxi- mately 10 seconds after the wipers are turned on. The headlights will also turn off when the wipers are turned off if they ...

  • Page 218

    Key off power delay when this feature is selected, the power window switches, radio, hands–free system (if equipped), dvd video system (if equipped), power sunroof (if equipped), and power outlets will remain active for up to 60 minutes after the ignition switch is turned off. Opening a vehicle door...

  • Page 219

    • tire pressure monitor system (shows the current pressure of all four road tires.) for additional informa- tion, refer to “tire pressure monitor system” in section 5 of this manual. Note: tires heat up during normal driving conditions. Heat will cause the tire pressure to increase from 2 to 6 psi (...

  • Page 220

    Two types of signals there are two basic types of radio signals: am or amplitude modulation, in which the transmitted sound causes the amplitude, or height, of the radio waves to vary; and fm or frequency modulation, in which the frequency of the wave is varied to carry the sound. Electrical disturb...

  • Page 221

    Sales code req — am/fm stereo radio and 6–disc cd/dvd changer (mp3/wma aux jack) note: the radio sales code is located on the lower right side of your radio faceplate. Operating instructions - radio mode note: the ignition switch must be in the on or acc position to operate the radio. Power switch/v...

  • Page 222

    To seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection. Holding either button will bypass stations without stopping until you release it. Scan button pressing the scan button causes the tuner to search for the next listenable stat...

  • Page 223

    3. After adjusting the hours, press the right side tune/ scroll control knob to set the minutes. The minutes will begin to blink. 4. Adjust the minutes using the right side tune/ scroll control knob. Press the tune/scroll control knob to save the time change. 5. To exit, press any button/knob or wai...

  • Page 224

    Push the rotary tune/scroll control knob a third time and treble will display. Turn the tune/scroll control knob to the right or left to increase or decrease the treble tones. Push the rotary tune/scroll control knob a fourth time and balance will display. Turn the tune/ scroll control knob to the r...

  • Page 225

    Program type 16-digit character display jazz jazz news news nostalgia nostalga oldies oldies personality persnlty public public rhythm and blues r & b religious music rel musc religious talk rel talk rock rock soft soft soft rock soft rck soft rhythm and blues soft r&b sports sports talk talk progra...

  • Page 226

    Note: turn the tune/scroll control knob to scroll through the entries. Push the audio/select button to select an entry and make changes. • dvd enter - when the disc is in dvd menu mode, selecting dvd enter will allow you to play the current highlighted selection. Use the remote control to scroll up ...

  • Page 227

    • vest ch1/ch2 - allows the user to change the mode of either the ir1 or ir2, wireless headphones by pressing the audio/select button (if equipped). • set home clock - pressing the select button allows you to set the clock. Turn the tune/scroll control knob to adjust the hours and then press and tur...

  • Page 228

    Subtitles — if equipped selecting this item allows you to choose between subtitle off or on. Audio drc — if equipped selecting this item allows you to limit maximum audio dynamic range. The default is set to 9high,9 and under this setting, dialogues will play at 11 db higher than if the setting is 9...

  • Page 229

    You may add a second station to each pushbutton by repeating the above procedure with this exception: press the set button twice and set 2 will show in the display window. Each button can be set for set 1 and set 2 in both am and fm. This allows a total of 12 am, 12 fm, and 12 satellite (if equipped...

  • Page 230

    Note: the ignition switch must be in the on or acc position to operate the radio. Load button — loading compact disc(s) press the load button and the pushbutton with the corresponding number (1-6) where the cd is being loaded. The radio will display please wait and prompt when to insert disc. After ...

  • Page 231

    Scan button (cd mode) press the scan button to scan through each track on the cd currently playing. Time button (cd mode) press this button to change the display from a large cd playing time display to a small cd playing time display. Rw/ff (cd mode) press and hold ff (fast forward) and the cd playe...

  • Page 232

    The radio uses the following limits for file systems: • maximum number of directory levels: 8 • maximum number of files: 255 • maximum number of folders: 100 • maximum number of characters in file/folder names: • level 1: 12 (including a separator 9.9 and a three- character extension) • level 2: 31 ...

  • Page 233

    Mpeg specification sampling fre- quency (khz) bit rate (kbps) mpeg-1 audio layer 3 48, 44.1, 32 320, 256, 224, 192, 160, 128, 112, 96, 80, 64, 56, 48 mpeg-2 audio layer 3 24, 22.05, 16 160, 128, 144, 112, 96, 80, 64, 56, 48 wma specification sampling fre- quency (khz) bit rate (kbps) wma 44.1 and 48...

  • Page 234

    To increase the speed of disc loading, it is recommended to use cd-r media and single-session discs. To create a single-session disc, enable the “disc at once” option before writing to the disc. List button (disc mode for mp3/wma play) pressing the list button will bring up a list of all folders on ...

  • Page 235

    Pressing the aux button will change the mode to auxil- iary device if the aux jack is connected. Note: the aux device must be turned on and the device’s volume set to the proper level. If the aux audio is not loud enough, turn the device’s volume up. If the aux audio sounds distorted, turn the devic...

  • Page 236

    Operating instructions - hands-free phone (uconnect t) (if equipped) refer to “hands-free communication (uconnect t)” in section 3. Operating instructions - satellite radio mode (if equipped) refer to “satellite radio” in this section. Operating instructions - video entertainment system (ves t) (if ...

  • Page 237

    Sales code res — am/fm stereo radio with cd player (mp3 aux jack) note: the radio sales code is located on the lower right side of your radio faceplate. Operating instructions - radio mode note: the ignition switch must be in the on or acc position to operate the radio. Power switch/volume control (...

  • Page 238

    Seek buttons press and release the seek buttons to search for the next listenable station in am/fm mode. Press the right switch to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection. Holding either button will bypass stations wit...

  • Page 239

    Time button press the time button and the time of day will display. In am or fm mode, pressing the time button will switch between the time and frequency displays. Clock setting procedure 1. Press and hold the time button, until the hours blink. 2. Adjust the hours by turning the right side tune/ sc...

  • Page 240

    Tune control turn the rotary tune/scroll control knob clockwise to increase or counterclockwise to decrease the frequency. Setting the tone, balance, and fade push the rotary tune/scroll control knob and bass will display. Turn the tune/scroll control knob to the right or left to increase or decreas...

  • Page 241

    Toggle the music type button to select the following format types: program type 16-digit character display no program type or un- defined none adult hits adlt hit classical classicl classic rock cls rock college college country country foreign language language information inform jazz jazz news news...

  • Page 242

    By pressing the seek button when the music type icon is displayed, the radio will be tuned to the next frequency station with the same selected music type name. The music type function only operates when in the fm mode. If a preset button is activated while in the music type (program type) mode, the...

  • Page 243

    Stations to be stored into pushbutton memory. The sta- tions stored in set 2 memory can be selected by pressing the pushbutton twice. Every time a preset button is used, a corresponding button number will display. Buttons 1 - 6 these buttons tune the radio to the stations that you commit to pushbutt...

  • Page 244

    Caution! • this cd player will accept 4–3/4 in (12 cm) discs only. The use of other sized discs may damage the cd player mechanism. • do not use adhesive labels. These labels can peel away and jam the player mechanism. • res is a single cd player. Do not attempt to insert a second cd if one is alrea...

  • Page 245

    Time button press this button to change the display from a large cd playing time display to a small cd playing time display. Rw/ff press the rw button to stop the cd at the beginning of the current cd track/title. Press and hold ff (fast forward) and the cd player will begin to fast forward until ff...

  • Page 246

    Files properly and may be unable to play the file nor- mally. Udf and apple hfs formats are not supported. The radio uses the following limits for file systems: • maximum number of folder levels: 8 • maximum number of files: 255 • maximum number of folders. (the radio display of file names and folde...

  • Page 247

    Rates (vbr) are also supported. The majority of mp3 files use a 44.1 khz sampling rate and a 192, 160, 128, 96 or vbr bit rates. Mpeg specification sampling fre- quency (khz) bit rate (kbps) mpeg-1 audio layer 3 48, 44.1, 32 320, 256, 224, 192, 160, 128, 112, 96, 80, 64, 56, 48, 40, 32 mpeg-2 audio ...

  • Page 248

    List button (cd mode for mp3 play) pressing the list button will bring up a list of all folders on the disc. Scrolling up or down the list is done by turning the tune/scroll control knob. Selecting a folder by pressing the tune/scroll control knob will begin playing the files contained in that folde...

  • Page 249

    Time button (auxiliary mode) press this button to change the display to time of day. The time of day will display for five seconds (when ignition is off). Operating instructions - hands-free phone (uconnect t) (if equipped) refer to “hands-free communication (uconnect t)” in section 3. Operating ins...

  • Page 250

    Through the system’s wireless headphones. This means rear-seat passengers can watch a dvd on the optional rear seat entertainment system, while the driver and front-seat passenger listen to the radio. Other special features include direct tune, music type selections, easy store presets, backup camer...

  • Page 251

    3. To move the hour forward, touch the screen where the word “hour” with the arrow pointing upward is dis- played. To move the hour backward, touch the screen where the word “hour” with the arrow pointing down- ward is displayed. 4. To move the minute forward, touch the screen where the word “min” w...

  • Page 252

    Touch the screen where the words “show time if radio is off” are displayed to change the current setting. Changing the time zone 1. Turn on the multimedia system. 2. Touch the screen where the time is displayed. The clock setting menu will appear on the screen. 3. Touch the screen where the words “s...

  • Page 253

    The satellite navigation capability combines a global- positioning system (gps)-based navigation system with an integrated color screen to provide maps, turn identi- fication, selection menus, and instructions for selecting a variety of destinations and routes. A shared hdd for the navigation system...

  • Page 254

    Clock setting procedure the gps receiver in this system is synchronized to the time data being transmitted by the gps satellites. The satellites’ clock is greenwich mean time (gmt). This is the worldwide standard for time. This makes the sys- tem’s clock very accurate once the appropriate time zone ...

  • Page 255

    3. When this feature is on, a check mark will appear in the box next to the words “daylight savings.” touch the screen where the words “daylight savings” are dis- played to change the current setting. Setting the user clock if you wish to set the clock to a time different from the system clock, you ...

  • Page 256

    2. Touch the screen where the time is displayed. The clock setting menu will appear on the screen. 3. When this feature is on, a check mark will appear in the box next to the words “show time if radio is off.” touch the screen where the words “show time if radio is off” are displayed to change the c...

  • Page 257

    Controlling the ipod t using radio buttons to get into the uci (ipod t) mode and access a connected ipod t, press the aux button on the radio faceplate. Once in the uci (ipod t) mode, the ipodt audio track (if available from ipod t) will start playing over the vehicle audio system. Play mode when sw...

  • Page 258

    Pressing and releasing the ff button will go forward five seconds of the current track. Seek buttons use the seek buttons to move to the previous or the next track. If the left (down) button is pressed during the first two seconds of the current track, it will go back to the previous track in the li...

  • Page 259

    List or browse mode during play mode, pressing any of the following buttons will take you to list mode. List mode enables you to scroll through the list of menus and tracks on the ipod t device. Tune/scroll knob in the list mode, the tune/scroll knob functions in a similar manner as the scroll wheel...

  • Page 260

    After pressing a preset button, you will see the list you are in on the top line and the first item in that list on the second line. To exit the list mode without selecting a track, press the same preset button again to go back to play mode. List button pressing the list button will take to the top ...

  • Page 261

    Number 888-539-7474, or visit the sirius web site at www.Sirius.Com, or at www.Siriuscanada.Ca for cana- dian residents. Electronic serial number/sirius identification number (esn/sid) please have the following information available when calling: 1. The electronic serial number/sirius identification...

  • Page 262

    Antenna will cause decreased performance. Larger lug- gage items such as bikes should be placed as far rearward as possible, within the loading design of the rack. Do not place items directly on or above the antenna. Reception quality satellite reception may be interrupted due to one of the followin...

  • Page 263

    Info button pressing the info button will cycle between artist, song title, and composer (if available) information. Also, pressing and holding the info button for an additional three seconds will make the radio display the song title all of the time (press and hold again to return to normal display...

  • Page 264

    Set button – to set the pushbutton memory when you are receiving a channel that you wish to commit to pushbutton memory, press the set button. The symbol set 1 will now show in the display window. Select the button (1-6) you wish to lock onto this channel and press and release that button. If a butt...

  • Page 265

    Sirius backseat tv™ — if equipped satellite video uses direct satellite receiver broadcasting technology to provide streaming video coast to coast. The subscription service provider is sirius satellite radio. Sirius backseat tv™ offers three video channels for family entertainment, directly from its...

  • Page 266

    Lowering the display screen remote control location understanding your instrument panel 265 4.

  • Page 267

    Remote sound system controls — if equipped the remote sound system controls are located on the rear surface of the steering wheel. Reach behind the wheel to access the switches. The right-hand control is a rocker-type switch with a pushbutton in the center and controls the volume and mode of the sou...

  • Page 268

    The button located in the center of the left-hand control will tune to the next preset station that you have pro- grammed in the radio preset pushbutton. Cd player pressing the top of the switch once will go to the next track on the cd. Pressing the bottom of the switch once will go to the beginning...

  • Page 269

    Radio operation and cellular phones under certain conditions, the cellular phone being on in your vehicle can cause erratic or noisy performance from your radio. This condition may be lessened or eliminated by relocating the cellular phone antenna. This condition is not harmful to the radio. If your...

  • Page 270

    Blower control the blower control rotary knob (on the left) controls the blower and can be set in one of four speeds and off. The blower fan motor will remain on un- til the system is turned to the off position or the ignition is turned off. Temperature control the temperature control rotary knob (i...

  • Page 271

    Side window demister grilles. Some airflow is delivered to the floor while in defrost so that comfort can be maintained. Floor air flows through the floor outlets located under the instrument panel and into the rear seating area through vents under the front seats. Some airflow is delivered to defro...

  • Page 272

    Located on the control panel. Conditioned air will be directed through the outlets selected by the mode control. A light in the snowflake button shows that the air conditioning is on. Slight changes in engine speed or power may be noticed when the air conditioning compressor is on. This is a normal ...

  • Page 273

    Note: the numbers on the temperature dial represent a comfort setting when the mode knob is set to auto, and not the actual air temperature. Turn the mode control (on the right) knob to auto, and place the blower control (on the left) to either lo auto or hi auto. The lo auto position should be used...

  • Page 274

    Note: • the surface of the climate control panel, and the top center of the instrument panel should be kept free of debris due to the climate control sensor’s location. Mud on the windshield may also cause poor operation of this system. • to provide you with maximum comfort in the auto- matic mode, ...

  • Page 275

    274 understanding your instrument panel.

  • Page 276

    Note: regardless of the type of operation, when a temperature knob is set to the full clockwise or full counterclockwise position, the system will deliver full hot or full cold air out of the ducts, respectively. The operator can override the auto mode setting and select the direction of the air by ...

  • Page 277

    Flows through the registers in the back of the center console, and under the front seats to the rear seat passengers. These registers can be closed to block airflow. The center console outlets deliver conditioned air while the floor outlets deliver heated air. Panel air flows through the outlets loc...

  • Page 278

    Defrost or defrost/floor modes. Attempting to use the recirculation while in these modes will cause the led in the button to blink and then turn off. Rear climate control — if equipped the manual rear climate control system has one floor air outlet (passenger side), and two panel outlets in the rear...

  • Page 279

    The rear temperature, blower speed, and mode control can be adjusted as desired by the third row seat occu- pants. Note: the rear climate control system cannot be con- trolled from the front seat; it can only be turned on and off. All control of the rear system must be performed by the rear occupant...

  • Page 280

    Caution! Interior air enters the manual rear zone climate control system through an intake grille located in the passenger side trim panel behind the third seat. The heater outlets are located in the passenger side trim panel just behind the sliding door. Do not block or place objects directly in fr...

  • Page 281

    Operating tips window fogging windows will fog on the inside when the humidity inside the vehicle is high. This often occurs in mild or cool temperatures when it’s rainy or humid. In most cases, turning on the air conditioning (pressing the snowflake button) will clear the fog. Adjust the temperatur...

  • Page 282

    When using the air conditioner in extremely heavy traffic, in hot weather, especially when towing a trailer, additional engine cooling may be required. If this situa- tion is encountered, operate the transmission in a lower gear to increase engine rpm, coolant flow and fan speed. When stopped in hea...

  • Page 283

    Operating tips chart 282 understanding your instrument panel.

  • Page 284: Starting And Operating

    Starting and operating contents m starting procedures . . . . . . . . . . . . . . . . . . . . . 287 ▫ normal starting . . . . . . . . . . . . . . . . . . . . . . 288 ▫ extremely cold weather (below 220°f or 229°c) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 288 ▫ if engine fails to sta...

  • Page 285

    ▫ shifting procedures . . . . . . . . . . . . . . . . . . . . 302 ▫ quadra-drive iit system — if equipped . . . . . 305 m on-road driving tips . . . . . . . . . . . . . . . . . . . 305 m off-road driving tips . . . . . . . . . . . . . . . . . . . 306 ▫ when to use 4wd low range — if equipped . . . ....

  • Page 286

    ▫ tread wear indicators . . . . . . . . . . . . . . . . . . 329 ▫ life of tire . . . . . . . . . . . . . . . . . . . . . . . . . 330 ▫ replacement tires . . . . . . . . . . . . . . . . . . . . . 331 ▫ alignment and balance . . . . . . . . . . . . . . . . . 332 m tire chains . . . . . . . . . . . . ....

  • Page 287

    ▫ cruising range . . . . . . . . . . . . . . . . . . . . . . . 352 ▫ replacement parts . . . . . . . . . . . . . . . . . . . . . 352 m adding fuel . . . . . . . . . . . . . . . . . . . . . . . . . . 352 ▫ fuel filler cap (gas cap) . . . . . . . . . . . . . . . 352 m vehicle loading . . . . . . . . ....

  • Page 288

    Starting procedures before starting your vehicle, adjust your seat, adjust the inside and outside mirrors, fasten your seat belt, and if present, instruct all other occupants to buckle their seat belts. Warning! • never leave children alone in a vehicle. Leaving unattended children in a vehicle is d...

  • Page 289

    Normal starting the shift lever must be in the neutral or park position before you can start the engine. Apply the brakes before shifting into any driving gear. Note: normal starting of either a cold or a warm engine is obtained without pumping or depressing the accelerator pedal. Do not press the a...

  • Page 290

    If engine fails to start warning! • never pour fuel or other flammable liquids into the throttle body air inlet opening in an attempt to start the vehicle. This could result in a flash fire causing serious personal injury. • do not attempt to push or tow your vehicle to get it started. Unburned fuel...

  • Page 291

    After starting the idle speed is controlled automatically and it will decrease as the engine warms up. Engine block heater — if equipped the engine block heater warms engine coolant and permits quicker starts in cold weather. Connect the heater cord to a ground-fault interrupter protected 110-115 vo...

  • Page 292

    Automatic transmission caution! Damage to the transmission may occur if the follow- ing precautions are not observed: • shift into park only after the vehicle has come to a complete stop. • shift into or out of reverse only after the vehicle has come to a complete stop and the engine is at idle spee...

  • Page 293

    1. Firmly set the parking brake. 2. Using a flat blade screwdriver, carefully remove the shift lock manual override cover, which is located on the prndl bezel. 3. Depress and maintain firm pressure on the brake pedal. 4. Using the screwdriver, reach into the manual override opening. Press and hold t...

  • Page 294

    Brake/transmission interlock system this system prevents you from moving the shift lever out of park and into any gear unless the brake pedal is pressed. This system is active only while the ignition switch is in the on position. Always depress the brake pedal first, before moving the shift lever ou...

  • Page 295

    Warning! It is dangerous to move the shift lever out of park or neutral if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in reverse. You could lose control of the vehicle and hit someone or something. Only s...

  • Page 296

    Electronic range select (ers)operation the electronic range select (ers) shift control allows you to move the shift lever left (-) or right (+) when the shift lever is in the drive position, allowing the selection of the desired top gear. For example, if the driver shifts the transmission into 3 (th...

  • Page 297

    Note: to select the proper gear position for maximum deceleration (engine braking), move the shift lever to the left “d(-)” and hold it there. The transmission will shift to the range from which the vehicle can best be slowed down. Overdrive operation the automatic transmission includes an electroni...

  • Page 298

    Over temp” message may display, and the transmis- sion may downshift out of overdrive until the transmis- sion cools down. After cool down, the transmission will resume normal operation. In high ambient temperatures with sustained high engine speed and load, an upshift, followed shortly thereafter b...

  • Page 299

    Activated. Pressing the switch a second time restores normal operation. If the tow/haul mode is desired, the switch must be pressed each time the engine is started. Transmission limp home mode transmission function is monitored for abnormal condi- tions. If a condition is detected that could result ...

  • Page 300

    Drops below a calibrated speed, or during acceleration, the clutch automatically and smoothly disengages. The feature is operational in overdrive and in drive. Note: the torque converter clutch will not engage until the transmission fluid and engine coolant are warm [usually after 1 to 3 mi (1.6 to ...

  • Page 301

    Spinning the wheels, due to the frustration of not freeing the vehicle, may lead to transmission overheating and failure. Allow the engine to idle with the shift lever in neutral for at least one minute after every five rocking-motion cycles. This will minimize overheating and reduce the risk of tra...

  • Page 302

    Quadra-trac ii t operating instructions/precautions — if equipped the quadra-trac ii t transfer case is fully automatic in the normal driving 4wd hi mode. The quadra-trac ii t transfer case provides three mode positions — 4wd hi, neutral, and 4wd low. This transfer case is fully automatic in the 4wd...

  • Page 303

    Shift positions for additional information on the appropriate use of each transfer case mode position, see the information below: 4wd hi all roads surfaces such as ice, snow, gravel, sand, and dry hard pavement. Neutral disengages both the front and rear driveshafts from the powertrain. To be used f...

  • Page 304

    4wd low to 4wd hi with the vehicle at speeds of 0 to 3 mph (0 to 5 km/h), key on or engine running, shift the transmission into neutral, and raise the transfer case t-handle. The “4wd low” indicator light in the instrument cluster, will flash and go out when the shift is complete. Release the t-hand...

  • Page 305

    Neutral shift procedure 1. Key on, engine off. 2. Vehicle stopped, with foot on brake. 3. Place transmission into neutral. 4. Hold down the neutral “pin” switch (with a pen, etc.) for four seconds until the led lamp by the switch starts to blink indicating shift in progress. The lamp will stop blink...

  • Page 306

    Quadra-drive ii t system — if equipped the optional quadra-drive ii t system features three torque transfer couplings. The couplings include elsd (electronic limited-slip differential) front and rear axles and quadra-trac ii t transfer case. The optional elsd axles are fully automatic and require no...

  • Page 307

    Off-road driving tips note: prior to off-road driving, remove the front air dam to prevent damage. The front air dam is attached to the lower front fascia with quarter turn fasteners, and can be removed by hand. When to use 4wd low range — if equipped when off-road driving, shift to 4wd low for addi...

  • Page 308

    Flowing water if the water is swift flowing and rising (as in storm run-off) avoid crossing until the water level recedes and/or the flow rate is reduced. If you must cross flowing water avoid depths in excess of 9 in (23 cm). The flowing water can erode the streambed causing your vehicle to sink in...

  • Page 309

    Hill climbing note: before attempting to climb a hill, determine the conditions at the crest and/or on the other side. Before climbing a steep hill, shift the transmission to a lower gear and shift the transfer case to 4wd low. Use first gear and 4wd low for very steep hills. If you stall or begin t...

  • Page 310

    Traction downhill shift the transmission into a low gear, and the transfer case into 4wd low range. Let the vehicle go slowly down the hill with all four wheels turning against engine compression drag. This will permit you to control the vehicle speed and direction. When descending mountains or hill...

  • Page 311

    Warning! Abrasive material in any part of the brakes may cause excessive wear or unpredictable braking. You might not have full braking power when you need it to prevent an accident. If you have been operating your vehicle in dirty conditions, get your brakes checked and cleaned as necessary. • if y...

  • Page 312

    Be sure the parking brake is firmly set when parked and the shift lever is in the park position. When parking on a hill, you should apply the parking brake before placing the shift lever in park, otherwise the load on the transmission locking mechanism may make it difficult to move the shift lever o...

  • Page 313

    When parking on a hill, turn the front wheels toward the curb on a downhill grade, and away from the curb on an uphill grade. The parking brake should always be applied whenever the driver is not in the vehicle. Anti-lock brake system the anti-lock brake system (abs) is designed to aid the driver in...

  • Page 314

    Warning! Pumping of the anti-lock brakes will diminish their effectiveness and may lead to an accident. Pumping makes the stopping distance longer. Just press firmly on your brake pedal when you need to slow down or stop. Warning! • the anti-lock brake system (abs) cannot prevent the natural laws of...

  • Page 315

    Caution! The anti-lock brake system (abs) is subject to possible detrimental effects of electronic interference caused by improperly installed aftermarket radios or telephones. Note: during severe braking conditions, a pulsing sensation may occur and a clicking noise will be heard. This is normal, i...

  • Page 316

    Build up between the tire tread and the road. This hydroplaning action can cause loss of traction, braking ability, and control. • after going through deep water or a car wash, brakes may become wet, resulting in decreased performance and unpredictable braking action. Dry the brakes by gentle, inter...

  • Page 317

    Caution! Prolonged operation of the steering system at the end of the steering wheel travel will increase the steering fluid temperature and it should be avoided when possible. Damage to the power steering pump may occur. Multi-displacement system (mds) — 5.7l engine only this feature offers improve...

  • Page 318

    • european metric tire sizing is based on european design standards. Tires designed to this standard have the tire size molded into the sidewall beginning with the section width. The letter 9p9 is absent from this tire size designation. Example: 215/65r15 96h. • lt (light truck)-metric tire sizing i...

  • Page 319

    Tire sizing chart example: size designation: p = passenger car tire size based on u.S. Design standards 9....Blank....9 = passenger car tire based on european design standards lt = light truck tire based on u.S. Design standards t = temporary spare tire 31 = overall diameter in inches (in) 215 = sec...

  • Page 320

    Example: service description: 95 = load index —a numerical code associated with the maximum load a tire can carry h = speed symbol —a symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions —the maximum speed correspon...

  • Page 321

    Tire identification number (tin) the tin may be found on one or both sides of the tire, however, the date code may only be on one side. Tires with white sidewalls will have the full tin, including the date code, located on the white sidewall side of the tire. Look for the tin on the outboard side of...

  • Page 322

    Tire loading and tire pressure tire placard location note: the proper cold tire inflation pressure is listed on either the face of the driver’s door or the driver’s side b-pillar. Tire and loading information placard this placard tells you important information about the: 1) number of people that ca...

  • Page 323

    Loading the vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size, and cold tire inflation pressures specified on the tire and loading informati...

  • Page 324

    Available cargo and luggage load capacity is 650 lbs (295 kg) {(since 5 x 150 = 750, and 1400 – 750 = 650 lbs (295 kg)}. 5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in st...

  • Page 325

    324 starting and operating.

  • Page 326

    Warning! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. Tires — general information tire pressure proper tire inflation pressur...

  • Page 327

    Economy improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Underinflation also increases tire rolling resistance and results in higher fuel consumption. Ri...

  • Page 328

    Check tire pressure. Do not make a visual judgement when determining proper inflation. Radial tires may look properly inflated even when they are underinflated. Caution! After inspecting or adjusting the tire pressure, al- ways reinstall the valve stem cap (if equipped). This will prevent moisture a...

  • Page 329

    Tire pressures for high speed operation the manufacturer advocates driving at safe speeds within posted speed limits. Where speed limits or condi- tions are such that the vehicle can be driven at high speeds, maintaining correct tire inflation pressure is very important. Increased tire pressure and ...

  • Page 330

    Tire spinning when stuck in mud, sand, snow, or ice conditions, do not spin your vehicle’s wheels above 35 mph (55 km/h). Warning! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause tire dam- age or failure. A tire could explode and injure some- one. Do not ...

  • Page 331

    Becomes 1/16 in (2 mm). When the indicators appear in two or more adjacent grooves, the tire should be re- placed. Many states have laws requiring tire replacement at this point. Life of tire the service life of a tire is dependent upon various factors including but not limited to: • driving style •...

  • Page 332

    Replacement tires the tires on your new vehicle provide a balance of many characteristics. They should be inspected regularly for wear and correct cold tire inflation pressure. The manu- facturer strongly recommends that you use tires equiva- lent to the originals in size, quality and performance wh...

  • Page 333

    Caution! Replacing original tires with tires of a different size may result in false speedometer and odometer readings. Alignment and balance poor suspension alignment may result in: • fast tire wear • uneven tire wear, such as feathering and one-sided wear • vehicle pull to the left or right tires ...

  • Page 334

    • use sae class “s” tire chains or traction devices only. • follow tire chain manufacturer’s instructions for mounting chains. • install chains snugly and tighten after 1/2 mi (1 km) of driving. • do not exceed 30 mph (48 km/h), unless otherwise specified by the chain manufacturer. • drive cautiousl...

  • Page 335

    The suggested rotation method is the “forward-cross” shown in the following diagram. Tire pressure monitor system (tpms) the tire pressure monitoring system (tpms) will warn the driver of a low tire pressure based on the vehicle recommended cold tire pressure. The tire pressure will vary with temper...

  • Page 336

    Warning threshold for any reason, including low tem- perature effects, or natural pressure loss through the tire. The tpm system will continue to warn the driver of low tire pressure as long as the condition exists, and will not turn off until the tire pressure is at or above recom- mended cold tire...

  • Page 337

    Caution! The tpms has been optimized for the original equipment tires and wheels. Tpms pressures have been established for the tire size equipped on your vehicle. Undesirable system operation or sensor damage may result when using replacement equip- ment that is not of the same size, type, and/or st...

  • Page 338

    Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability. • the tpms is not a substitute for proper tire mainte- nance, and it is the driver’s responsibility to maintain correct tire pressure using an accurate tire gauge, even if un...

  • Page 339

    The tire pressure monitoring telltale light will illuminate in the instrument cluster, and an au- dible chime will be activated when one or more of the four active road tire pressures are low. Should this occur, you should stop as soon as possible, check the inflation pressure of each tire on your v...

  • Page 340

    Matching full size spare tire is swapped with a low pressure road tire, the next ignition key cycle will still show the tire pressure monitoring telltale light to be on, and a chime to sound. Driving the vehicle for up to 10 minutes above 15 mph (24 km/h) will turn off the tire pressure monitoring t...

  • Page 341

    Note: it is particularly important, for you to check the tire pressure in all of your tires regularly and to maintain the proper pressure. The tire pressure monitor system (tpms) consists of the following components: • receiver module • four tire pressure monitoring sensors • three trigger modules (...

  • Page 342

    Should a low tire condition occur on any of the four active road tire(s), you should stop as soon as possible, and inflate the low tire(s) that is “flashing” on the graphic display to the vehicle’s recommended cold tire pressure. The system will automatically update, the graphic dis- play of the pre...

  • Page 343

    Note: your system can be set to display pressure units in psi, kpa, or bar. If the ignition key is cycled, this sequence will repeat, providing the system fault still exists. If the system fault no longer exists, the tire pressure monitoring telltale light will no longer flash, the 9check tpm system...

  • Page 344

    Case, the 9check tpm system9 message is then fol- lowed by a graphic display, with pressure values still shown. This indicates the pressure values are still being received from the tpm sensors. However, the system still needs to be serviced as long as the 9check tpm system 9 message exists. Note: if...

  • Page 345

    Pressure value. For each subsequent ignition key cycle, a chime will sound, the tire pressure monitoring telltale light will flash on and off for 75 seconds and then remain on solid, and the evic will display a 9check tpm system 9 message for three seconds and then display dashes (- -) in place of t...

  • Page 346

    Fuel requirements 3.7/4.7l engines (if equipped) all engines (except 5.7l engines) are de- signed to meet all emissions regulations and provide excellent fuel economy and performance when using high-quality un- leaded “regular” gasoline having an oc- tane rating of 87. The use of premium gasoline is...

  • Page 347

    Over 40 auto manufacturer’s worldwide have issued and endorsed consistent gasoline specifications (the world- wide fuel charter, wwfc) to define fuel properties necessary to deliver enhanced emissions, performance, and durability for your vehicle. The manufacturer recom- mends the use of gasoline th...

  • Page 348

    Mmt in gasoline mmt is a manganese containing metallic additive that is blended into some gasoline to increase octane. Gasoline blended with mmt provides no performance advantage beyond gasoline of the same octane number without mmt. Gasoline blended with mmt reduces spark plug life and reduces emis...

  • Page 349

    • an out-of-tune engine, or certain fuel or ignition malfunctions, can cause the catalytic converter to overheat. If you notice a pungent burning odor or some light smoke, your engine may be out of tune or malfunctioning and may require immediate service. Contact your authorized dealer for service a...

  • Page 350

    • guard against carbon monoxide with proper mainte- nance. Have the exhaust system inspected every time the vehicle is raised. Have any abnormal conditions repaired promptly. Until repaired, drive with all side windows fully open. • keep the liftgate closed when driving your vehicle to prevent carbo...

  • Page 351

    Caution! Only vehicles with the e-85 fuel filler cap (gas cap) can operate on e-85. Ethanol fuel (e-85) e-85 is a mixture of approximately 85% fuel ethanol and 15% unleaded gasoline. Warning! Ethanol vapors are extremely flammable and could cause serious personal injury. Never have any smok- ing mat...

  • Page 352

    For best results, a refueling pattern that alternates be- tween e-85 and unleaded gasoline should be avoided. When you do switch fuels, it is recommended that; • you do not switch when the fuel gauge indicates less than one–quarter full • you do not add less than 5 gallons (23 l) when refueling • yo...

  • Page 353

    Cruising range because e-85 fuel contains less energy per gallon/liter than gasoline, you will experience an increase in fuel consumption. You can expect your mpg and your driv- ing range to decrease by about 30% compared to gasoline operation. Replacement parts many components in your flexible fuel...

  • Page 354

    Caution! Damage to the fuel system or emission control sys- tem could result from using an improper fuel cap (gas cap). A poorly fitting cap could let impurities into the fuel system. Also, a poorly fitting aftermar- ket cap can cause the malfunction indicator light to illuminate, due to fuel vapors...

  • Page 355

    Caution! To avoid fuel spillage and overfilling, do not “top off” the fuel tank after filling. Note: when the fuel nozzle “clicks” or shuts off, the fuel tank is full. Warning! • never have any smoking materials lit in or near the vehicle when the gas cap is removed or the tank filled. • never add f...

  • Page 356

    Warning! A fire may result if gasoline is pumped into a portable container that is inside of a vehicle. You could be burned. Always place gas containers on the ground while filling. Caution! Damage to the fuel system or emission control sys- tem could result from using an improper fuel tank filler c...

  • Page 357

    Included on this label and indicates the month, day, and hour of manufacture. The bar code that appears on the bottom of the label is your vin. Gross vehicle weight rating (gvwr) the gvwr is the total permissible weight of your vehicle including driver, passengers, vehicle, options, trailer tongue w...

  • Page 358

    Curb weight the curb weight of a vehicle is defined as the total weight of the vehicle with all fluids, including vehicle fuel, at full capacity conditions, and with no occupants or cargo loaded into the vehicle. The front and rear curb weight values are determined by weighing your vehicle on a comm...

  • Page 359

    Caution! Do not load your vehicle any heavier than the gvwr or the maximum front and rear gawr. If you do, parts on your vehicle can break, or it can change the way your vehicle handles. This could cause you to lose control. Also, overloading can shorten the life of your vehicle. Trailer towing in t...

  • Page 360

    Gross combination weight rating (gcwr) the gcwr is the total permissible weight of your vehicle and trailer when weighed in combination. (note that gcwr ratings include a 150 lbs (68 kg) allowance for the presence of a driver). Gross axle weight rating (gawr) the gawr is the maximum capacity of the ...

  • Page 361

    Weight-distributing hitch a weight-distributing hitch system works by applying leverage through spring (load) bars. They are typically used for heavier loads, to distribute trailer tongue weight to the tow vehicle’s front axle and the trailer axle(s). When used in accordance with the manufacturer’s ...

  • Page 362

    Weight-distributing hitch system improper adjustment of weight-distributing system starting and operating 361 5.

  • Page 363

    Trailer hitch classification your vehicle may be factory equipped for safe towing of trailers weighing over 3,500 lbs (1 587 kg) with the optional trailer tow prep package. See your authorized dealer for package content. The following chart provides the industry standard for the maximum trailer weig...

  • Page 364

    Trailer towing weights (maximum trailer weight ratings) the following chart provides the maximum trailer weight ratings towable for your given drivetrain. Engine model gcwr (gross com- bined wt. Rating) frontal area max. Gtw (gross trailer wt.) max. Trailer tongue wt. (see note) 3.7l 4x2 8,670 lbs (...

  • Page 365

    Note: the trailer tongue weight must be considered as part of the combined weight of occupants and cargo, and should never exceed the weight referenced on the tire and loading information placard. Refer to the “tire– safety information” section in this manual. Trailer and tongue weight always load a...

  • Page 366

    Note: remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options, or dealer-installed options, must be considered as part of the total load on your vehicle. Refer to the tire and loading information plac- ard in the “tire—safety i...

  • Page 367

    Warning! Improper towing can lead to an injury accident. Follow these guidelines to make your trailer towing as safe as possible: make certain that the load is secured in the trailer and will not shift during travel. When trailering cargo that is not fully secured, dynamic load shifts can occur that...

  • Page 368

    3. Gawr 4. Trailer tongue weight rating for the trailer hitch utilized (this requirement may limit the ability to always achieve the 10% to 15% range of tongue weight as a percentage of total trailer weight). Towing requirements — tires − do not attempt to tow a trailer while using a compact spare t...

  • Page 369

    − an electronically-actuated trailer brake controller is required when towing a trailer with electronically- actuated brakes. When towing a trailer equipped with a hydraulic surge-actuated brake system, an electronic brake controller is not required. − trailer brakes are recommended for trailers ove...

  • Page 370

    The trailer tow package may include a 4 and 7–pin wiring harness. Use a factory approved trailer harness and connector. The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector. Refer to the following illustrations. Towing tips before setting ou...

  • Page 371

    Towing tips — automatic transmission the drive range can be selected when towing. How- ever, if frequent shifting occurs while in this range, the tow/haul mode (if equipped) or a lower gear range should be selected. Note: using the tow/haul mode (if equipped) or a lower gear range while operating th...

  • Page 372

    − air conditioning turn off temporarily. Recreational towing (behind motorhome, etc.) towing – 2wd models recreational towing is allowed only if the driveshaft is removed. Towing with the rear wheels on the ground while the driveshaft is connected can result in severe transmission damage. Towing — q...

  • Page 373

    Caution! It is necessary to follow these steps to be certain that the transfer case is fully in neutral before recre- ational towing to prevent damage to internal parts. 1. Depress the brake pedal. 2. Turn the ignition key on, engine off. 3. Shift the transmission into neutral. 4. Shift the transfer...

  • Page 374

    9. Shift the transmission into park. 10. Place the ignition key in the off position, and remove key. 11. Apply the parking brake. 12. Attach the vehicle to the tow vehicle with tow bar. 13. Release the parking brake. Caution! Transmission damage may occur if the transmission is shifted into park wit...

  • Page 375

    Displayed on the evic (electronic vehicle information center). Refer to “electronic vehicle information center (evic)” in section 4 of this manual. 5. Shift the transmission into park. 6. Start the engine. 7. Shift the transmission into drive. Note: when shifting out of transfer case neutral, turnin...

  • Page 376

    Caution! Do not use a bumper-mounted clamp-on tow bar on your vehicle. The bumper face bar will be damaged. Snow plow snow plows, winches, and other aftermarket equipment should not be added to the front end of your vehicle. The airbag crash sensors may be affected by the change in the front end str...

  • Page 378: Contents

    What to do in emergencies contents m hazard warning flashers . . . . . . . . . . . . . . . . . 378 m if your engine overheats . . . . . . . . . . . . . . . . . 379 m jacking and tire changing . . . . . . . . . . . . . . . . 380 ▫ jack location . . . . . . . . . . . . . . . . . . . . . . . . 380 ▫ sp...

  • Page 379

    Hazard warning flashers your vehicle’s hazard warning flasher is an emergency warning system. When you activate it, all front and rear directional signals will flash intermittently. Use it when your vehicle is disabled on, or near, the road. It warns other drivers to steer clear of you and your vehi...

  • Page 380

    If your engine overheats in any of the following situations, you can reduce the potential for overheating by taking the appropriate ac- tion. • on the highways — slow down. • in city traffic — while stopped, put transmission in neutral, but do not increase engine idle speed. Note: there are steps th...

  • Page 381

    Jacking and tire changing warning! • getting under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never get any part of your body under a vehicle that is on a jack. If you need to get under a raised vehicle, take it to a service center wh...

  • Page 382

    Spare tire stowage the spare tire is stowed under the rear of the vehicle by means of a cable winch mechanism. To remove or stow the spare, use the jack handle to rotate the “spare tire drive” nut. The nut is located under a plastic cover at the center-rear of the cargo floor area, just inside the l...

  • Page 383

    Caution! The winch mechanism is designed for use with the jack extension tube only. Use of an air wrench or other power tools is not recommended and can dam- age the winch. When the spare is clear, tilt the retainer at the end of the cable and pull it through the center of the wheel. Preparations fo...

  • Page 384

    Jacking instructions 1. Remove the spare tire, jack, and tools from storage. 2. Loosen (but do not remove) the wheel lug nuts by turning them to the left one turn while the wheel is still on the ground. 3. Assemble the jack and jacking tools as shown. Connect jack handle driver (a) to two extensions...

  • Page 385

    4. Locate the jack as shown. For the front axle, place it under the front lower control arm as shown. For the rear axle, place it under the axle near the wheel to be changed. Ensure the jack is closest to the inside of the wheel when jacking on the rear axle. Do not raise the vehicle until you are s...

  • Page 386

    Warning! Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. 6. Remove the lug nuts and wheel. 7. Position the spare wheel/tire on the vehicle and install the lug nuts with ...

  • Page 387

    Tire until you hear the winch “ratchet” three times. Double check to ensure the tire is snug against the underbody of the vehicle. Damage to the winch cable may result if the vehicle is driven with the tire loose. Warning! Do not use power tools to winch the tire up or down. Impact type tools may da...

  • Page 388

    2. Park the booster vehicle within cable reach but with- out letting the vehicles touch. Set the parking brake on both vehicles, place the transmission in park, and turn the ignition off. 3. Turn off the heater, radio, and all unnecessary electri- cal loads. 4. Connect one end of a jumper cable to t...

  • Page 389

    Warning! Any procedure other than above could result in: 1. Personal injury caused by electrolyte squirting out the battery vent; 2. Personal injury or property damage due to battery explosion; 3. Damage to charging system of booster vehicle or of immobilized vehicle. Warning! • you should not try t...

  • Page 390

    Emergency tow hooks — if equipped if your vehicle is equipped with tow hooks, there will be one in the rear and two mounted on the front of the vehicle. The rear hook will be located on the driver’s side of the vehicle. Note: for off-road recovery, it is recommended to use both of the front tow hook...

  • Page 391

    Towing a disabled vehicle 2wd models only provided the transmission is operable, tow only in neu- tral at speeds not exceeding 30 mph (48 km/h), for distances of not more than 15 mi (24 km). Towing at more than 30 mph (48 km/h) or for more than 15 mi (24 km), can cause severe transmission damage. If...

  • Page 392: Maintaining Your Vehicle

    Maintaining your vehicle contents m engine compartment – 3.7l . . . . . . . . . . . . . . . 394 m engine compartment – 4.7l . . . . . . . . . . . . . . . 395 m engine compartment – 5.7l . . . . . . . . . . . . . . . 396 m onboard diagnostic system — obd ii . . . . . . . . 397 ▫ loose fuel filler cap...

  • Page 393

    ▫ air conditioner maintenance . . . . . . . . . . . . . 409 ▫ power steering fluid check . . . . . . . . . . . . . . 410 ▫ body lubrication . . . . . . . . . . . . . . . . . . . . . 411 ▫ windshield wiper blades . . . . . . . . . . . . . . . . 412 ▫ windshield washers — front and rear . . . . . 412 ...

  • Page 394

    ▫ front fog light . . . . . . . . . . . . . . . . . . . . . . 445 ▫ rear tail, stop, turn signal, and backup lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 446 ▫ center high mounted stop light (chmsl) . . . 448 m fluids and capacities . . . . . . . . . . . . . . . . . . . 449 m flu...

  • Page 395

    Engine compartment – 3.7l 394 maintaining your vehicle.

  • Page 396

    Engine compartment – 4.7l maintaining your vehicle 395 7.

  • Page 397

    Engine compartment – 5.7l 396 maintaining your vehicle.

  • Page 398

    Onboard diagnostic system — obd ii your vehicle is equipped with a sophisticated onboard diagnostic system called obd ii. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide ex...

  • Page 399

    Loose fuel filler cap message after fuel is added, the vehicle diagnostic system can determine if the fuel filler cap is loose, improperly installed, or damaged. A “check gascap” message will be displayed in the evic (refer to section 4 of this manual). Tighten the gas cap until a 9clicking9 sound i...

  • Page 400

    Normally, the obd system will be ready. The obd system may not be ready if your vehicle was recently serviced, if you recently had a dead battery, or a battery replacement. If the obd system should be determined not ready for the i/m test, your vehicle may fail the test. Your vehicle has a simple ig...

  • Page 401

    Regardless of whether your vehicle’s obd system is ready or not ready, if the mil symbol is illuminated during normal vehicle operation, you should have your vehicle serviced before going to the i/m station. The i/m station can fail your vehicle because the mil symbol is on with the engine running. ...

  • Page 402

    Warning! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the proper equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic. Maintenance procedures the pages ...

  • Page 403

    Caution! Overfilling or underfilling the crankcase will cause aeration or loss of oil pressure. This could damage your engine. Change engine oil refer to the maintenance schedule in section 8 for recommended engine oil change intervals. Engine oil selection for best performance and maximum protectio...

  • Page 404

    Note: vehicles equipped with a 5.7l engine must use sae 5w-20 oil. Failure to do so may result in improper operation of the multiple displacement system (mds). Refer to “multi-displacement system” in section 5 for more details. Lubricants, which do not have both the engine oil certi- fication mark a...

  • Page 405

    High-quality filters should be used to assure most effi- cient service. Mopar t engine oil filters are high-quality oil filters and are recommended. Drive belts — check condition and tension belt tension is controlled by means of an automatic tensioner. No belt tension adjustments are required. Howe...

  • Page 406

    Engine air cleaner filter refer to the maintenance schedule in section 8 for recommended engine air cleaner filter change intervals. Warning! The air induction system (air cleaner, hoses, etc) can provide a measure of protection in the case of engine backfire. Do not remove the air induction system ...

  • Page 407

    Caution! Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition. In the event of engine malfunction, particularly involv- ing engine misfire or other apparent loss of perfor- mance, have your vehicle serviced promptly. Contin- ued operation of your veh...

  • Page 408

    To minimize the possibility of catalytic converter dam- age: • do not shut off the engine or interrupt the ignition, when the transmission is in gear and the vehicle is in motion. • do not try to start the engine by pushing or towing the vehicle. • do not idle the engine with any spark plug wires di...

  • Page 409

    Warning! • battery fluid is a corrosive acid solution and can burn or even blind you. Don’t allow battery fluid to contact your eyes, skin or clothing. Don’t lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area imme- diately with large amounts of water. • ba...

  • Page 410

    Air conditioner maintenance for best possible performance, your air conditioner should be checked and serviced by an authorized dealer at the start of each warm season. This service should include cleaning of the condenser fins and a performance test. Drive belt condition should also be checked at t...

  • Page 411

    Note: use only manufacturer approved a/c system sealers, stop leak products, seal conditioners, compres- sor oil, and refrigerants. Refrigerant recovery and recycling r-134a air conditioning refrigerant is a hydrofluorocar- bon (hfc) that is endorsed by the environmental pro- tection agency (epa) an...

  • Page 412

    Warning! Fluid level should be checked on a level surface with the engine off to prevent injury from moving parts, and to ensure accurate fluid level reading. Do not overfill. Use only the manufacturer’s recommended fluid. If necessary, add fluid to restore to the proper indicated level. With a clea...

  • Page 413

    Windshield wiper blades the rubber edges of the wiper blades and the windshield should be cleaned periodically with a sponge or soft cloth and a mild nonabrasive cleaner to remove accumulations of salt or road film. Operation of the wipers on dry glass for long periods may cause deterioration of the...

  • Page 414

    Warning! Commercially available windshield washer solvents are flammable. They could ignite and burn you. Care must be exercised when filling or working around the washer solution. Exhaust system the best protection against carbon monoxide entry into the vehicle body is a properly maintained engine ...

  • Page 415

    Cooling system warning! You or others can be badly burned by hot antifreeze/ coolant or steam from your radiator. If you see or hear steam coming from under the hood, don’t open the hood until the radiator has had time to cool. Never try to open a cooling system pressure cap when the radiator or coo...

  • Page 416

    Cooling system — drain, flush, and refill at the intervals shown on the maintenance schedule, the system should be drained, flushed and refilled. Refer to section 8 of this manual. If the solution is dirty and contains a considerable amount of sediment, clean and flush with reliable cooling system c...

  • Page 417

    Adding coolant your vehicle has been built with an improved antifreeze/ coolant that allows extended maintenance intervals. This antifreeze/coolant can be used up to 5 years or 100,000 mi (160 000 km) before replacement. To prevent reducing this extended maintenance period, it is important that you ...

  • Page 418

    Please note that it is the owner’s responsibility to main- tain the proper level of protection against freezing ac- cording to the temperatures occurring in the area where the vehicle is operated. Note: mixing antifreeze/coolant types will decrease the life of the antifreeze/coolant and will require...

  • Page 419

    Your local authorities to determine the disposal rules for your community. To prevent ingestion by animals and children, do not store ethylene glycol-based antifreeze/ coolant in open containers or allow it to remain in puddles on the ground. If ingested by a child, contact a physician immediately. ...

  • Page 420

    • check antifreeze/coolant freeze point in the radiator and in the coolant recovery bottle. If antifreeze/ coolant needs to be added, contents of coolant recov- ery bottle must also be protected against freezing. • if frequent antifreeze/coolant additions are required, or if the level in the coolant...

  • Page 421

    Are present. Components should be replaced immedi- ately if there is any evidence of degradation that could cause failure. Fuel system connections electronic fuel injection high pressure fuel systems are designed with tubes and special connects, connections and clamps, which have unique material cha...

  • Page 422

    Inspect all hose clamps and couplings to make sure they are secure and no leaks are present. Note: often fluids such as oil, power steering fluid, and brake fluid are used during assembly plant opera- tions to ease the assembly of hoses to couplings. There- fore, oil wetness at the hose-coupling are...

  • Page 423

    With disc brakes, the fluid level can be expected to fall as the brake linings wear. However, an unexpected drop in fluid level may be caused by a leak and a system check should be conducted. Refer to fluids, lubricants and genuine parts in this section for the correct fluid type. Warning! Use of a ...

  • Page 424

    Front/rear axle fluid front axle fluid level check lubricant should be to the bottom of the oil fill hole. Rear axle fluid level check lubricant should be 1/2 inch (1 cm) below the oil fill hole. Adding fluid add lubricant only at the fill hole and only to the level specified above. Selection of lub...

  • Page 425

    Caution! When installing plugs, do not overtighten. You could damage them and cause them to leak. Selection of lubricant use only the manufacturer’s recommended fluid. Refer to fluids, lubricants, and genuine parts in this section for correct fluid type. Automatic transmission selection of lubricant...

  • Page 426

    Policy is the use of special dyes to aid in detecting fluid leaks. In addition, avoid using transmission sealers as they may adversely affect seals. Fluid level check (3.7l engine) regular fluid level checks are not required. For this reason, the dipstick is omitted. If you notice fluid loss or shif...

  • Page 427

    Fluid level check (4.7l and 5.7l engine) check the fluid level while the transmission is at normal operating temperature. This occurs after at least 15 mi (25 km) of driving. At normal operating temperature the fluid cannot be held comfortably between the fingertips. To check the fluid level properl...

  • Page 428

    Caution! Be aware that if the fluid temperature is below 50°f (10°c) it may not register on the dipstick. Do not add fluid until the temperature is elevated enough to produce an accurate reading. 7. Check for leaks. Release parking brake. To prevent dirt and water from entering the transmission afte...

  • Page 429

    Caution! Under frequent heavy-duty driving conditions, change all lubricants, and lubricate body compo- nents, all driveline joints and steering linkage more often than in normal service, to prevent excessive wear. Appearance care and protection from corrosion protection of body and paint from corro...

  • Page 430

    Washing • wash your vehicle regularly. Always wash your ve- hicle in the shade using mopar t car wash or a mild car wash soap, and rinse the panels completely with clear water. • if insects, tar, or other similar deposits have accumu- lated on your vehicle, use mopar t super kleen bug and tar remove...

  • Page 431

    • if you detect any stone chips or scratches in the paint, touch them up immediately. The cost of such repairs is considered the responsibility of the owner. • if your vehicle is damaged due to an accident or similar cause which destroys the paint and protective coating, have your vehicle repaired a...

  • Page 432

    • for tough stains, apply mopart total clean or a mild soap solution to a clean, damp cloth and remove stain. Use a fresh, damp towel to remove soap residue. • for grease stains, apply mopart multi-purpose cleaner to a clean, damp cloth and remove stain. Use a fresh, damp towel to remove soap residu...

  • Page 433

    Warning! Do not use volatile solvents for cleaning purposes. Many are potentially flammable, and if used in closed areas, they may cause respiratory harm. Cleaning headlights your vehicle has plastic headlights that are lighter and less susceptible to stone breakage than glass headlights. Plastic is...

  • Page 434

    2. Dry with a soft tissue. Seat belt maintenance do not bleach, dye or clean the belts with chemical solvents or abrasive cleaners. This will weaken the fabric. Sun damage will also weaken the fabric. If the belts need cleaning, use mopar t total clean, a mild soap solution, or lukewarm water. Do no...

  • Page 435

    Cav- ity cartridge fuse mini-fuse description 1 30 amp green audio amp (b+) 2 15 amp blue sunroof (b+) 3 10 amp red htd mirror (ebl) 4 20 amp yellow rr pwr out (b+) 5 10 amp red rr hvac (r/o) (commander only) 6 spare (b+) 7 20 amp yellow door locks (b+) 8 spare (b+) 9 20 amp yellow pwr outlet (b+) c...

  • Page 436

    Cav- ity cartridge fuse mini-fuse description 14 20 amp yellow cigar ltr (r/a) 15 10 amp red tire pressure trans- ducers (r/o) 16 10 amp red upper & lower switch bank, diag. Connector, cluster (b+) 17 15 amp blue flipper glass (b+) 19 spare (r/s) 20 10 amp red sentry key remote entry module (skreem)...

  • Page 437

    Underhood fuses (power distribution center) cav- ity cartridge fuse mini-fuse description 1 50 amp green ptc heater 1 (diesel only) cav- ity cartridge fuse mini-fuse description 2 40 amp green hid headlamps 3 50 amp green ptc heater 2 (diesel only) 4 30 amp pink power outlets 5 50 amp red ptc heater...

  • Page 438

    Cav- ity cartridge fuse mini-fuse description 11 40 amp green hvac blower 12 30 amp pink rear wiper, ign r/o 13 40 amp green rear window de- froster (ebl)/heated mirror 14 30 amp pink rear hvac (if equipped) 15 — spare 16 50 amp red asd 17 30 amp pink abs pump 18 40 amp green accessory delay, seats ...

  • Page 439

    Cav- ity cartridge fuse mini-fuse description 27 20 amp yellow hd washer (if equipped) 28 30 amp green abs valves 29 20 amp yellow pcm batt (gasoline only) 30 — spare 31 — spare 32 15 amp blue powertrain control module (diesel only) 33 20 amp yellow final drive control module (fdcm) e-diff 34 — spar...

  • Page 440

    Underhood fuses (integrated power module) cav- ity cartridge fuse mini-fuse description 8 10 amp red lt park lamps cav- ity cartridge fuse mini-fuse description 9 10 amp red trailer-tow park lamps 10 10 amp red rt park lamps 12 20 amp yellow front control module (fcm) batt #4 13 20 amp yellow front ...

  • Page 441

    Cav- ity cartridge fuse mini-fuse description 18 20 amp yellow front control module (fcm) batt #1 19 20 amp yellow lt trailer-tow stop/ turn 20 20 amp yellow front control module (fcm) batt #3 21 20 amp yellow rt trailer-tow stop/ turn 22 30 amp pink final drive control module (fdcm) mod 23 50 amp r...

  • Page 442

    Ensure adequate system lubrication to minimize the possibility of compressor damage when the system is started again. Replacement bulbs interior lights bulb type glove box light . . . . . . . . . . . . . . . . . . . . . . . . . 194 grab handle light . . . . . . . . . . . . . . . . L002825w5w overhea...

  • Page 443

    Bulb replacement head light 1. Open the hood. 2. Remove the headlamp cover. Insert a finger into each hole of the headlamp cover, and pull upward to unsnap the rear edge of the cover from the two upper lamp mounting brackets. Slide the cover rearward to disengage the front edge from beneath the tab ...

  • Page 444

    3. Disconnect the electrical connector. 4. Turn the low or high beam bulb 1/4 turn counterclock- wise to unlock it from the housing. 5. Pull the bulb and base straight out from the opening in the reflector. Caution! Do not touch the new bulb with your fingers. Oil contamination will severely shorten...

  • Page 445

    Front turn signal 1. Turn the steering wheel all the way to the left or right. 2. Reach into the front wheel house ahead of the front wheel to unsnap and lift the cover over the access hole in the front of the wheel house splash shield. Access to the bulb can be gained through the wheel liner hole. ...

  • Page 446

    4. Turn the socket on the bottom of the front lamp unit housing 1/4 turn counterclockwise to unlock it. 5. Pull the socket and bulb straight out from the opening in the housing. 6. Disconnect the electrical connector. 7. Pull the base of the bulb straight out of the socket. Caution! Do not touch the...

  • Page 447

    3. Reach through the access hole to access the back of the front fog light housing on the back of the front fascia. 4. Disconnect the electrical connector. 5. Turn the socket on the back of the housing 1/4 turn counterclockwise to unlock it. 6. Pull the socket and bulb straight out from the opening ...

  • Page 448

    3. Pull the outboard side of the rear lamp unit rearward far enough to unsnap the two ball studs on the outboard side of the lamp housing from the two plastic grommets in the quarter outer panel. Pull the lamp unit rearward far enough away to access the bulbs. 4. Firmly grasp the appropriate bulb so...

  • Page 449

    7. Pull the base of the bulb straight out of the socket. Caution! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol. Center high mounted stop light (chmsl) 1. Remove ...

  • Page 450

    Fluids and capacities u.S. Metric fuel (approximate) 21 gallons 79 liters engine oil with filter 3.7 liter engine (sae 5w-20, api certified) 5 quarts 4.7 liters 4.7 liter engine (sae 5w-20, api certified) 6 quarts 5.7 liters 5.7 liter engine (sae 5w-20, api certified) 7 quarts 6.6 liters cooling sys...

  • Page 451

    Fluids, lubricants, and genuine parts engine component fluid, lubricant, or genuine part engine coolant mopar t antifreeze/coolant 5 year/100,000 mile formula hoat (hybrid organic additive technology) engine oil (3.7l/4.7l/5.7l en- gines) use api certified sae 5w-20 engine oil, meeting the requireme...

  • Page 452

    Chassis component fluid, lubricant, or genuine part automatic transmission mopar t atf+4 automatic transmission fluid transfer case (nv140 single speed only) mopar t atf+4 automatic transmission fluid transfer case (nv245 two speed only) mopar t nv 247/245 transfer case lubricant axle differential (...

  • Page 454: Maintenance Schedules

    Maintenance schedules contents m emission control system maintenance . . . . . . . . 454 m maintenance schedule — gasoline engines . . . . 454 ▫ required maintenance intervals . . . . . . . . . . . 456 8 m a i n t e n a n c e s c h e d u l e s.

  • Page 455

    Emission control system maintenance the “scheduled” maintenance services, listed in bold type must be done at the times or mileages specified to assure the continued proper functioning of the emission control system. These, and all other maintenance services included in this manual, should be done t...

  • Page 456

    • change your engine oil more often if you drive your vehicle off-road for an extended period of time. • under no circumstances should oil change intervals exceed 6,000 mi (10,000 km) or 6 months, whichever comes first. Your authorized dealer will reset the oil change indicator message after complet...

  • Page 457

    At each oil change • change the engine oil filter. • inspect the brake hoses and lines. Caution! Failure to perform the required maintenance items may result in damage to the vehicle. Required maintenance intervals note: ** vehicles built with the 4.7l engine are equipped with sixteen spark plugs, o...

  • Page 458

    Perform maintenance every (where time and mileage are listed, follow the interval that occurs first.) maintenance items miles kilometers or months change the engine oil and engine oil filter. 6,000 10 000 6 rotate tires. 6,000 10 000 6 if using your vehicle for any of the following: dusty or off-roa...

  • Page 459

    Perform maintenance every (where time and mileage are listed, follow the interval that occurs first.) maintenance items miles kilometers or months replace the engine air cleaner filter. 30,000 50 000 30 inspect the transfer case fluid. 30,000 50 000 30 replace the top row of spark plugs (4.7l engine...

  • Page 460

    Perform maintenance every (where time and mileage are listed, follow the interval that occurs first.) maintenance items miles kilometers or months change the automatic transmission fluid & filter. 120,000 200 000 120 replace accessory drive belt(s) (3.7l, 4.7l and 5.7l en- gines). 120,000 200 000 12...

  • Page 462: Contents

    If you need consumer assistance contents m suggestions for obtaining service for your vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 463 ▫ prepare for the appointment . . . . . . . . . . . . 463 ▫ prepare a list . . . . . . . . . . . . . . . . . . . . . . . . 463 ▫ be reasonable...

  • Page 463

    M publication order forms . . . . . . . . . . . . . . . . . . 468 m department of transportation uniform tire quality grades . . . . . . . . . . . . . . . . . . . . . . . . 469 ▫ treadwear . . . . . . . . . . . . . . . . . . . . . . . . . . 469 ▫ traction grades . . . . . . . . . . . . . . . . . . ....

  • Page 464

    Suggestions for obtaining service for your vehicle prepare for the appointment if you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty. Discuss additional charges with the service manager. ...

  • Page 465

    Special tools, and the latest information to ensure your vehicle is fixed correctly and in a timely manner. This is why you should always talk to your authorized dealer’s service manager first. Most matters can be re- solved with this process. • if for some reason you are still not satisfied, talk t...

  • Page 466

    Customer assistance for the hearing or speech impaired (tdd/tty) to assist customers who have hearing difficulties, the manufacturer has installed special tdd (telecommuni- cation devices for the deaf) equipment at its customer center. Any hearing or speech impaired customer, who has access to a tdd...

  • Page 467

    Warning! Engine exhaust, some of its constituents, and certain vehicle components contain, or emit, chemicals known to the state of california to cause cancer and birth defects or other reproductive harm. In addition, certain fluids contained in vehicles and certain prod- ucts of component wear cont...

  • Page 468

    Reporting safety defects in the 50 united states and washington, d.C. If you believe that your vehicle has a defect which could cause a crash or cause injury or death, you should immediately inform the national highway traffic safety administration (nhtsa) in addition to notifying the manufacturer. ...

  • Page 469

    Publication order forms to order the following manuals, you may use either the website or the phone numbers listed below. Visa, mas- tercard, american express, and discover orders are ac- cepted. If you prefer mailing your payment, please call for an order form. Note: a street address is required wh...

  • Page 470

    Call toll free at: • 1–800–890–4038 (u.S.) • 1–800–387–1143 (canada) or visit us on the worldwide web at: • www.Techauthority.Daimlerchrysler.Com • www.Daimlerchrysler.Ca/manuals department of transportation uniform tire quality grades the following tire grading categories were established by the na...

  • Page 471

    On specified government test surfaces of asphalt and concrete. A tire marked c may have poor traction perfor- mance. Warning! The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction chara...

  • Page 472: Index

    Index 10

  • Page 473

    Abs (anti-lock brake system) . . . . . . . . . . . . 196,312 adding fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . 352 adding washer fluid . . . . . . . . . . . . . . . . . . . . . 185 adjustable pedals . . . . . . . . . . . . . . . . . . . . . . . 143 air cleaner, engine (engine air cle...

  • Page 474

    Fluid and filter changes . . . . . . . . . . . . . . . . . 424 fluid level check . . . . . . . . . . . . . . . . . . . 425,426 fluid type . . . . . . . . . . . . . . . . . . . . . . . . . . . 424 special additives . . . . . . . . . . . . . . . . . . . . . . 424 torque converter . . . . . . . . . . ....

  • Page 475

    Carbon monoxide warning . . . . . . . . . . . . . . . 72,348 cargo area features . . . . . . . . . . . . . . . . . . . . . . 182 cargo compartment . . . . . . . . . . . . . . . . . . . . . . 182 luggage carrier . . . . . . . . . . . . . . . . . . . . . . . 185 cargo load floor . . . . . . . . . . . ...

  • Page 476

    Drain, flush, and refill . . . . . . . . . . . . . . . . . . 415 inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . 414 points to remember . . . . . . . . . . . . . . . . . . . . 418 pressure cap . . . . . . . . . . . . . . . . . . . . . . . . . 417 radiator cap . . . . . . . . . . . ....

  • Page 477

    E-85 fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 349 electric remote mirrors . . . . . . . . . . . . . . . . . . . . 82 electrical outlet, auxiliary (power outlet) . . . . . . 177 electronic brake control system . . . . . . . . . . . . . 147 anti-lock brake system . . . . . . . . ...

  • Page 478

    Oil selection . . . . . . . . . . . . . . . . . . . . . . . 402,449 oil synthetic . . . . . . . . . . . . . . . . . . . . . . . . . 403 operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 overheating . . . . . . . . . . . . . . . . . . . . . . . . . . 379 starting . . . . . . . . . ...

  • Page 479

    Engine oil . . . . . . . . . . . . . . . . . . . . . . . . . . . 401 power steering . . . . . . . . . . . . . . . . . . . . . . . . 410 fluids, lubricants and genuine parts . . . . . . . . . . 450 fog light service . . . . . . . . . . . . . . . . . . . . . . . . 445 fog lights . . . . . . . . . . . ...

  • Page 480

    Tachometer . . . . . . . . . . . . . . . . . . . . . . . . . . 197 gear ranges . . . . . . . . . . . . . . . . . . . . . . . . . . . 293 general information . . . . . . . . . . . . . . . 20,26,111,344 glass cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . 432 gross axle weight rating . ....

  • Page 481

    Immobilizer (sentry key) . . . . . . . . . . . . . . . . . . . 17 infant restraint . . . . . . . . . . . . . . . . . . . . . . . . 61,62 inflation pressure tires . . . . . . . . . . . . . . . . . . . . 326 information center, vehicle . . . . . . . . . . . . . . . . . 203 inside rearview mirror . . ....

  • Page 482

    Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74,132 airbag . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59,196 alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 anti-lock . . . . . . . . . . . . . . . . . . . . . . . . . . . 196 automatic headlig...

  • Page 483

    Seat belt reminder . . . . . . . . . . . . . . . . . . . . . 201 security alarm (theft alarm) . . . . . . . . . . . . . . 197 service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 442 service engine soon (malfunction indicator) . . . 195 side marker . . . . . . . . . . . . . . . . . . ...

  • Page 484

    Electric remote . . . . . . . . . . . . . . . . . . . . . . . . 82 exterior folding . . . . . . . . . . . . . . . . . . . . . . . . 82 heated . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83 outside . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 rearview . . . . . . . ....

  • Page 485

    Onboard diagnostic system . . . . . . . . . . . . . . 397,398 opener, garage door (homelink t) . . . . . . . . . . . 167 outside rearview mirrors . . . . . . . . . . . . . . . . . . 81 overdrive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 296 overdrive off switch . . . . . . . . . . . ...

  • Page 486

    Preparation for jacking . . . . . . . . . . . . . . . . . . . . 382 pretensioners seat belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 programmable electronic features . . . . . . . . . . . . 213 programming transmitters (remote keyless entry) . . . . . . . . . . . . . . . . . . ....

  • Page 487

    Remote control starting system . . . . . . . . . . . . . . . . . . . . . . . . 27 remote keyless entry (rke) . . . . . . . . . . . . . . . . . 22 remote sound system (radio) controls . . . . . . . . 266 remote starting system . . . . . . . . . . . . . . . . . . . . 27 replacement bulbs . . . . . . ....

  • Page 488

    Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116 adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . 116 cleaning . . . . . . . . . . . . . . . . . . . . . . . . . 430,431 easy entry . . . . . . . . . . . . . . . . . . . . . . . . . . . 129 fold and tumble rear ...

  • Page 489

    Spark plugs . . . . . . . . . . . . . . . . . . . . . . . . . . . . 404 specifications fuel (gasoline) . . . . . . . . . . . . . . . . . . . . . . . . 345 oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 402 speed control (cruise control) . . . . . . . . . . . . . . 144 speedomete...

  • Page 490

    Tire and loading information placard . . . . . . . . . 321 tire identification number (tin) . . . . . . . . . . . . . 320 tire markings . . . . . . . . . . . . . . . . . . . . . . . . . . 316 tire safety information . . . . . . . . . . . . . . . . . . . . 316 tires . . . . . . . . . . . . . . . . . ...

  • Page 491

    Traction control . . . . . . . . . . . . . . . . . . . . . . . . . 148 traction control light . . . . . . . . . . . . . . . . . . . . 197 trailer sway control (tsc) . . . . . . . . . . . . . . . . . 155 trailer towing . . . . . . . . . . . . . . . . . . . . . . . . . . 358 cooling system tips . . . ...

  • Page 492

    Vacuum/vapor harnesses . . . . . . . . . . . . . . . . . 419 vanity mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . 83 variance, compass . . . . . . . . . . . . . . . . . . . . . . . 212 vehicle certification label . . . . . . . . . . . . . . . . . 355 vehicle identification number (vi...

  • Page 493

    Commander o w n e r ’ s m a n u a l 2 0 0 8 2 0 0 8 c o m m a n d e r 81-326-0810 first edition printed in u.S.A..