1. DL manuals
  2. Jeep
  3. Automobile
  4. 2009 Liberty
  5. Owner's Manual

Jeep 2009 Liberty Owner's Manual

Other manuals for 2009 Liberty: Owner's Manual

Summary of 2009 Liberty

  • Page 1

    Liberty 2009 owner’s manual 2009 liber ty chrysler llc 81-326-0941 second edition printed in u.S.A..

  • Page 2

    Vehicles sold in canada with respect to any vehicles sold in canada, the name chrysler llc shall be deemed to be deleted and the name chrysler canada inc. Used in substitution therefor. Driving and alcohol drunken driving is one of the most frequent causes of accidents. Your driving ability can be s...

  • Page 3: Table Of Contents

    Table of contents section page 1 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 things to know before starting your vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 3 understanding the ...

  • Page 5: Introduction

    Introduction contents 䡵 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 䡵 rollover warning . . . . . . . . . . . . . . . . . . . . . . . 4 䡵 how to use this manual . . . . . . . . . . . . . . . . . . 5 䡵 warnings and cautions . . . . . . . . . . . . . . . . . . . 7 䡵 vehicle ide...

  • Page 6

    Introduction this owner’s manual has been prepared with the assis- tance of service and engineering specialists to acquaint you with the operation and maintenance of your vehicle. It is supplemented by a warranty information booklet and various customer-oriented documents. You are urged to read thes...

  • Page 7

    Failure to use driver and passenger seat belts provided is a major cause of severe or fatal injury. In fact, the u.S. Government notes that the universal use of existing seat belts could cut the highway death toll by 10,000 or more each year and could reduce disabling injuries by two million annuall...

  • Page 8

    6 introduction.

  • Page 9

    Warnings and cautions this owner’s manual contains warnings against op- erating procedures that could result in an accident or bodily injury. It also contains cautions against proce- dures that could result in damage to your vehicle. If you do not read this entire manual, you may miss important info...

  • Page 10

    Vehicle modifications/alterations warning! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death. 8 introduction.

  • Page 11: Contents

    Things to know before starting your vehicle contents 䡵 a word about your keys . . . . . . . . . . . . . . . . . 12 ▫ ignition key removal . . . . . . . . . . . . . . . . . . 12 ▫ key-in-ignition reminder . . . . . . . . . . . . . . . 14 䡵 sentry key威 . . . . . . . . . . . . . . . . . . . . . . . . ....

  • Page 12

    ▫ using the panic alarm . . . . . . . . . . . . . . . . . 24 ▫ programming additional transmitters . . . . . . 25 ▫ battery replacement . . . . . . . . . . . . . . . . . . . 25 ▫ general information . . . . . . . . . . . . . . . . . . . 26 䡵 remote starting system — if equipped . . . . . . . 27 ▫ ho...

  • Page 13

    ▫ driver and front passenger supplemental restraint system (srs) - airbags . . . . . . . . . . 53 ▫ child restraint . . . . . . . . . . . . . . . . . . . . . . . 71 䡵 engine break-in recommendations . . . . . . . . . . 80 䡵 safety tips . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 ▫ trans...

  • Page 14

    A word about your keys you can insert the double-sided keys into the locks with either side up. The authorized dealer that sold you your new vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys from your authorized dealer. Ask your authorized dea...

  • Page 15

    Note: • for vehicles not equipped with the electronic vehicle information center (evic), features such as the power window switches, radio, power sunroof or sky slider 威 (if equipped), and power outlets will remain active for 45 seconds after the ignition switch is turned to the lock position. Openi...

  • Page 16

    Warning! Never leave children alone in a vehicle. Leaving unattended children in a vehicle is dangerous for a number of reasons. A child or others could be seri- ously or fatally injured. Don’t leave the key in the ignition. A child could operate power windows, other controls, or move the vehicle. C...

  • Page 17

    Note: a key that has not been programmed is also considered an invalid key, even if it is cut to fit the ignition switch lock cylinder for that vehicle. During normal operation, after turning on the ignition switch, the vehicle security light will turn on for three seconds for a bulb check. If the l...

  • Page 18

    Replacement keys note: only keys that are programmed to the vehicle electronics can be used to start and operate the vehicle. Once a sentry key 威 is programmed to a vehicle, it cannot be programmed to any other vehicle. Caution! Always remove the sentry keys 威 from the vehicle and lock all doors whe...

  • Page 19

    3. Insert the second valid key into the ignition switch. Turn the ignition switch to the on position within 15 seconds. After 10 seconds, a chime will sound. In addition, the vehicle security light will begin to flash. Turn the ignition switch to the lock position and remove the second key. 4. Inser...

  • Page 20

    Vehicle security alarm — if equipped the vehicle security alarm monitors the vehicle doors, liftgate, and liftgate flip-up window for unauthorized entry and ignition for unauthorized operation. If something triggers the alarm, the vehicle security alarm will sound the horn intermittently, flash the ...

  • Page 21

    Cancel the arming process. If the vehicle security alarm arms successfully, the vehicle security light will flash at a slower rate to indicate the alarm is set. Note: for added security, whenever the security alarm is armed, the homelink 威/garage door opener (if equipped) is disabled as well. To dis...

  • Page 22

    Under “personal settings (customer-programmable fea- tures)” under “electronic vehicle information center (evic)” in section 4. The interior lights will fade to off after approximately 30 seconds or they will immediately fade to off once the ignition switch is turned on. Note: • the illuminated entr...

  • Page 23

    To unlock the doors and liftgate press and release the unlock button on the rke transmitter once to unlock the driver’s door or twice to unlock all doors and the liftgate. The turn signal lights will flash to acknowledge the unlock signal. The illumi- nated entry system will also turn on. Remote key...

  • Page 24

    Illuminated approach — if equipped this feature activates the headlights for up to 90 seconds when the doors are unlocked with the rke transmitter. The time for this feature is programmable on vehicles equipped with the electronic vehicle information center (evic). For details, refer to “illuminatio...

  • Page 25

    3. Test the feature from outside the vehicle by pressing the lock button on the rke transmitter. 4. Repeat these steps if you want to return this feature to its previous setting. Note: pressing the lock button on the rke transmit- ter while you are inside the vehicle will activate the security alarm...

  • Page 26

    Note: pressing the lock button on the rke transmit- ter while you are inside the vehicle will activate the security alarm. Opening a door with the security alarm activated will cause the alarm to sound. Press the un- lock button to deactivate the security alarm. To unlatch the liftgate flip-up windo...

  • Page 27

    The panic alarm will stay on for three minutes unless you turn it off by pressing the panic button a second time or if the vehicle speed is 5 mph (8 km/h) or greater. During the panic mode, the door locks and remote keyless entry (rke) system will function normally. Panic mode will not disarm the se...

  • Page 28

    2. With the rke transmitter buttons facing down, use a flat blade tool to pry the two halves of the rke transmit- ter case apart. Make sure not to damage the seal during removal. 3. Remove and replace the battery. Avoid touching the new battery with your fingers. Skin oils may cause battery deterior...

  • Page 29

    Note: changes or modifications not expressly ap- proved by the party responsible for compliance could void the user’s authority to operate the equipment. If your rke transmitter fails to operate from a normal distance, check for these two conditions: 1. Weak battery in rke transmitter. The expected ...

  • Page 30

    To enter remote start mode press and release the remote start button on the rke transmitter twice, within five sec- onds. The parking lights will flash and the horn will chirp twice (if programmed). Then, the engine will start and the vehicle will remain in the remote start mode for a 15-minute cycl...

  • Page 31

    Door locks manual door locks to lock each door, push the door lock plunger on each door trim panel downward. To unlock each door, pull the door lock plunger on each door trim panel upward. If the door lock plunger is down when you shut the door, the door will lock. Make sure the keys are not inside ...

  • Page 32

    Warning! (continued) • never leave children alone in a vehicle. Leaving unattended children in a vehicle is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Don’t leave the key in the ignition. A child could operate power win- dows, other controls, or move ...

  • Page 33

    If you press the power door lock switch while the key is in the ignition, and any front door is open, the power locks will not operate. This prevents you from acciden- tally locking your keys in the vehicle. Removing the key or closing the door will allow the locks to operate. A chime will sound if ...

  • Page 34

    3. Press the power door lock switch to lock the doors. 4. A single chime will indicate the completion of the programming. 5. Repeat these steps if you want to return this feature to its previous setting. Note: use the automatic door locks feature in accor- dance with local laws. Automatic unlock doo...

  • Page 35

    3. Press the power door unlock switch to unlock the doors. 4. A single chime will indicate the completion of the programming. Repeat these steps if you want to return this feature to its previous setting. Note: use the automatic unlock doors on exit feature in accordance with local laws. Child-prote...

  • Page 36

    Warning! Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child protection locks are engaged. Note: • after engaging the child protection door lock sys- tem, always test the door from the inside to make certain it is in the ...

  • Page 37

    Windows power windows the window controls on the driver’s door trim panel control all the door windows. There are single window controls on each passenger door trim panel, which operate the passenger door windows. The window controls will operate when the ignition switch is in the on or acc position...

  • Page 38

    To open the window part way, press the window switch to the first detent and release it when you want the window to stop. To stop the window from going all the way down during the auto-down operation, pull up on the switch briefly. For vehicles not equipped with the electronic vehicle information ce...

  • Page 39

    For vehicles not equipped with the electronic vehicle information center (evic), the power window switches will remain active for 45 seconds after the ignition switch is turned to the lock position. Opening either front door will cancel this feature. For vehicles equipped with the evic, the power wi...

  • Page 40

    Window lockout switch the window lockout switch on the driver’s door trim panel allows you to disable the window control on the other doors. To disable the window control on the other doors, press and release the window lock button (setting it in the down position). To enable the window controls, pr...

  • Page 41

    Reset it may be necessary at some point in time to reactivate the auto up feature. To do so, perform the following proce- dure: 1. Pull the window switch up to close window com- pletely and continue to hold the switch up for an additional two seconds after the window is closed. 2. Push the window sw...

  • Page 42

    Liftgate to open the liftgate, pull up (squeeze) on the handle and lift. Note: use the power door lock switch on either front door trim panel or the remote keyless entry (rke) transmitter to lock and unlock the liftgate. The manual door locks on the doors and the driver’s door lock cylinder will not...

  • Page 43

    Liftgate flipper glass the liftgate flipper glass is also unlocked when the liftgate is unlocked. To open the flipper glass, push up on the window switch located on the liftgate. Warning! To avoid injury, stand back when opening. Glass may automatically rise. Note: if a malfunction to the liftgate l...

  • Page 44

    Occupant restraints some of the most important safety features in your vehicle are the restraint systems. These include the front and rear seat belts for the driver and all passengers, front airbags for both the driver and front passenger, and side curtain airbags for the driver and passengers seate...

  • Page 45

    Inside of the vehicle. Everyone in a motor vehicle should be belted at all times to reduce or prevent injuries. Lap/shoulder belts all seating positions in your vehicle have combination lap/shoulder belts. The belt webbing retractor is de- signed to lock during very sudden stops or collisions. This ...

  • Page 46

    Warning! (continued) • two people should never be belted into a single seat belt. People belted together can crash into one another in an accident, hurting one another badly. Never use a lap/shoulder belt or a lap belt for more than one person, no matter what their size. Lap/shoulder belt operating ...

  • Page 47

    Warning! • a belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • a belt that is too loose will not protect you as well. In a sudden stop,...

  • Page 48

    Warning! (continued) • a shoulder belt placed behind you will not protect you from injury during a collision. You are more likely to hit your head in a collision if you do not wear your shoulder belt. The lap and shoulder belt are meant to be used together. 4. Position the lap belt across your thigh...

  • Page 49

    6. To release the belt, push the red button on the buckle. The belt will automatically retract to its stowed position. If necessary, slide the latch plate down the webbing to allow the belt to retract fully. Warning! A frayed or torn belt could rip apart in a collision and leave you with no protecti...

  • Page 50

    The shoulder belt anchorage to be adjusted in the upward position without pressing the release button. To verify the shoulder belt anchorage is latched, pull downward on the shoulder belt anchorage until it is locked into position. As a guide, if you are shorter than average, you will prefer a lower...

  • Page 51

    Seat belt pretensioner — if equipped the front passenger seat belt is equipped with a preten- sioning device that is designed to remove any slack from the seat belt systems in the event of a collision. These devices improve the performance of the seat belt by assuring that the belt is tight around t...

  • Page 52

    Beltalert 威 programming beltalert 威 can be enabled or disabled by your authorized dealer or by performing the following steps: note: chrysler llc does not recommend deactivating beltalert 威. 1. With all doors closed, and the ignition switch in any position except on or start, buckle the driver’s sea...

  • Page 53

    Automatic locking mode — if equipped in this mode, the shoulder belt is automatically pre- locked. However, the belt will still retract to remove any slack in the shoulder belt. When to use the automatic locking mode use the automatic locking mode anytime a child safety seat is installed in the rear...

  • Page 54

    Warning! • the belt and retractor assembly must be replaced if the seat belt assembly “automatic locking retrac- tor” feature or any other seat belt function is not working properly when checked according to the procedures in the service manual. • failure to replace the belt and retractor assembly c...

  • Page 55

    Driver and front passenger supplemental restraint system (srs) - airbags this vehicle has airbags for both the driver and front passenger as a supplement to the seat belt restraint systems. The driver’s airbag is mounted in the steering wheel. The passenger’s front airbag is mounted in the instrumen...

  • Page 56

    Note: the front airbags are certified to the federal regulations that allow less forceful deployment. The front airbags have a multistage inflator design. This may allow the airbag to have different rates of inflation that are based on collision severity and occupant size. The front passenger airbag...

  • Page 57

    Warning! • do not put anything on or around the front and side curtain airbag covers or attempt to manually open them. You may damage the airbags and you could be injured because the airbags are no longer functional. These protective covers for the airbag cushions are designed to open only when the ...

  • Page 58

    Trigger on the crash side of the vehicle in moderate-to- severe side collisions or on both sides of the vehicle in rollover collisions. In certain types of collisions, both the front and side airbags may be triggered. However, even in collisions where the airbags deploy, you need the seat belts to k...

  • Page 59

    If a child from 1 to 12 years old must ride in the front passenger seat because the vehicle is crowded, move the seat as far back as possible, and use the proper child restraint (refer to information on child restraint in this section). You should read the instructions provided with your child restr...

  • Page 60

    Airbag system components the airbag system consists of the following: • occupant restraint controller (orc) • airbag warning light • driver airbag • front passenger airbag • side curtain airbags above side windows • side remote acceleration sensors • steering wheel and column • instrument panel • in...

  • Page 61

    The orc also monitors the readiness of the electronic parts of the system whenever the ignition switch is in the start or on position. These include all of the items listed above except the passenger airbag disable (pad) indicator light, the instrument panel, and the steering wheel and column. If th...

  • Page 62

    Note: children 12 years and younger should always ride buckled up in a rear seat in an appropriate child restraint. • the passenger airbag disable (pad) indicator light (an amber light located in the center of the instrument panel) tells the driver and front passenger when the front passenger airbag...

  • Page 63

    The “pad indicator light” should not be illuminated when an adult passenger is properly seated in the front passenger seat. In this case, the airbag is ready to be inflated if a collision requiring an airbag occurs. For all other occupants, the “pad indicator light” will be illuminated indicating th...

  • Page 64

    Will cause the system to turn the airbag on. In this case, the ocs has classified the occupant of the seat as an adult. An adult occupant needs to sit in a normal position (with their feet on or near the floor) in order to be properly classified. Reclining the seat back too far may change how an occ...

  • Page 65

    Lodged under the seat and interferes with operation of the weight sensors, a fault will occur which turns on both the “pad indicator light” and the “airbag warning light.” once the lodged object is removed, the fault will be automatically cleared after a short period of time. • the driver and passen...

  • Page 66

    • the side impact srs side curtain airbags are de- signed to activate only in certain side collisions and rollover events. When the orc detects a collision requiring the side curtain airbag to inflate, it signals the inflators on the crash side of the vehicle or both sides of the vehicle for a rollo...

  • Page 67

    Warning! Unapproved modifications or service procedures to the front passenger seat assembly or its related com- ponents may inadvertently change the airbag deploy- ment in case of a frontal crash. This could result in death or serious injury to the front seat passenger if the vehicle is involved in...

  • Page 68

    Throat irritation, move to fresh air. If the irritation continues, see your doctor. If these particles settle on your clothing, follow the garment manufacturer’s in- structions for cleaning. • it is not advisable to drive your vehicle after the airbags have deployed. If you are involved in another c...

  • Page 69

    Maintaining your airbag system warning! • modifications to any part of the airbag system could cause it to fail when you need it. You could be injured if the airbag system is not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the stee...

  • Page 70

    Warning! (continued) • do not place or hang any items such as add-on video players on the front passenger seatback. The additional weight may cause the occupant classi- fication system to be unable to classify the front seat passenger correctly. This could allow the passenger frontal airbag to infla...

  • Page 71

    Event data recorder (edr) in the event of an accident, your vehicle is designed to record up to five seconds of specific vehicle data param- eters (see the following list) in an event data recorder prior to the moment of airbag deployment, or near deployment, and up to a quarter second of high-speed...

  • Page 72

    The u.S. Government and various states. Data of a poten- tially sensitive nature, such as would identify a particular driver, vehicle, or crash, will be treated confidentially. Confidential data will not be disclosed by chrysler llc to any third party except when: 1. Used for research purposes, such...

  • Page 73

    Child restraint everyone in your vehicle needs to be buckled up all the time, including babies and children. Every state in the united states and all canadian provinces require that small children ride in proper restraint systems. This is the law, and you can be prosecuted for ignoring it. Children ...

  • Page 74

    Infants and child restraints • safety experts recommend that children ride rearward-facing in the vehicle until they are at least one year old and weigh at least 20 lbs (9 kg). Two types of child restraints can be used rearward-facing: infant carriers and “convertible” child seats. • the infant carr...

  • Page 75

    The belt-positioning booster seat is for children weighing more than 40 lbs (18 kg), but who are still too small to fit the vehicle’s seat belts properly. If the child cannot sit with knees bent over the vehicle’s seat cushion while the child’s back is against the seatback, they should use a belt-po...

  • Page 76

    Warning! (continued) • a rearward- facing infant restraint should only be used in a rear seat. A rearward-facing infant re- straint in the front seat may be struck by a deploy- ing passenger airbag, which may cause severe or fatal injury to the infant. Here are some tips on getting the most out of y...

  • Page 77

    The child restraint using lower anchorages and upper tether straps from the child restraint to the vehicle structure. Latch-compatible child restraint systems are now avail- able. However, because the lower anchorages are to be introduced over a period of years, child restraint systems having attach...

  • Page 78

    Installing the latch-compatible child restraint system we urge you to carefully follow the directions of the manufacturer when installing your child restraint. Not all child restraint systems will be installed as described here. Again, carefully follow the installation instructions that were provide...

  • Page 79

    Many, but not all restraint systems will be equipped with separate straps on each side, with each having a hook or connector for attachment to the lower anchorage and a means of adjusting the tension in the strap. Forward- facing toddler restraints and some rear-facing infant restraints will also be...

  • Page 80

    Warning! Improper installation of a child restraint to the latch anchorages can lead to failure of an infant or child restraint. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint. Installing child restraints using th...

  • Page 81

    The buckle, turn the buckle around, and insert the latch plate into the buckle again. If you still can’t make the child restraint secure, try a different seating position. To attach a child restraint tether strap: route the tether strap over the seatback and attach the hook to the tether anchor loca...

  • Page 82

    Warning! An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchor positions directly behind the child seat to secure a child restraint top tether strap. Transporting pets airbags deploying in the front seat could harm your pet. An...

  • Page 83

    A new engine may consume some oil during its first few thousand miles (kilometers) of operation. This should be considered a normal part of the break-in and not inter- preted as an indication of difficulty. Safety tips transporting passengers never transport passengers in the cargo area. Warning! • ...

  • Page 84

    If it is necessary to sit in a parked vehicle with the engine running, adjust your heating or cooling controls to force outside air into the vehicle. Set the blower at high speed. If you are required to drive with the trunk/liftgate open, make sure that all windows are closed and the climate control...

  • Page 85

    Airbag warning light the light should come on and remain on for six to eight seconds as a bulb check when the ignition switch is first turned on. If the light is not lit during starting, see your authorized dealer. If the light stays on, flickers, or comes on while driving, have the system checked b...

  • Page 87: Contents

    Understanding the features of your vehicle contents 䡵 mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90 ▫ inside day/night mirror . . . . . . . . . . . . . . . . 90 ▫ automatic dimming mirror — if equipped . . . . . . . . . . . . . . . . . . . . . . . . . 90 ▫ outside mirrors . ...

  • Page 88

    䡵 voice recognition (vr) system — if equipped . . . . . . . . . . . . . . . . . . . . . . . . . . 122 ▫ voice recognition (vr) system operation . . . 122 ▫ commands . . . . . . . . . . . . . . . . . . . . . . . . 124 ▫ voice training . . . . . . . . . . . . . . . . . . . . . . 127 䡵 seats . . . . . ...

  • Page 89

    ▫ headlights with wipers (available with auto headlights only) . . . . . . . . . . . . . . . . 143 ▫ headlight time delay — if equipped . . . . . . 144 ▫ daytime running lights (drl) — if equipped . . . . . . . . . . . . . . . . . . . . . . . . . . 144 ▫ lights-on reminder . . . . . . . . . . . . . ...

  • Page 90

    䡵 rear park assist system — if equipped . . . . . . 158 ▫ system usage precautions . . . . . . . . . . . . . . 159 ▫ enabling and disabling the system . . . . . . . 161 ▫ system operation . . . . . . . . . . . . . . . . . . . . 162 䡵 garage door opener — if equipped . . . . . . . . 165 ▫ programming...

  • Page 91

    䡵 sky slider威 full length open roof . . . . . . . . . 174 ▫ sky slider威 usage precautions . . . . . . . . . . . 175 ▫ sky slider威 control . . . . . . . . . . . . . . . . . . . 177 ▫ opening the sky slider威 . . . . . . . . . . . . . . . 177 ▫ closing the sky slider威 . . . . . . . . . . . . . . . 178 ...

  • Page 92

    Mirrors inside day/night mirror a two-point pivot system allows for horizontal and vertical mirror adjustment. Adjust the mirror to center on the view through the rear window. Headlight glare can be reduced by moving the small control under the mirror to the night position (toward the rear of vehicl...

  • Page 93

    Caution! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror. Apply the solution onto a clean cloth and wipe the mirror clean. Outside mirrors to receive maximum benefit, adjust the outside mirror(s) to center on the adjacent lane of traffic and ...

  • Page 94

    Power mirrors the power mirror switch is located on driver’s door trim panel. Models with express window feature press and release the mirror select button marked l (left) or r (right) and then press one of the four arrow buttons to move the mirror in the direction the arrow is pointing. The selecti...

  • Page 95

    Heated mirrors — if equipped these mirrors are heated to melt frost or ice. This feature is activated whenever you turn on the rear window defroster. Refer to “rear window features” in this section, for further information. Illuminated vanity mirrors — if equipped an illuminated vanity mirror is on ...

  • Page 96

    2. Unclip the visor from the center clip. 3. Pull the sun visor toward the inside rearview mirror to extend it. Uconnect 姞 phone — if equipped note: the sales code rer and reu radios contain an integrated uconnect 威 phone. Refer to your “navigation user’s manual” for uconnect 威 phone operating instr...

  • Page 97

    Bluetooth 威 technology - the global standard that enables different electronic devices to connect to each other without wires or a docking station, so uconnect 威 phone works no matter where you stow your cellular phone (be it your purse, pocket, or briefcase), as long as your phone is turned on and ...

  • Page 98

    The radio display will be used for visual prompts from the uconnect 威 phone such as ⬙cell⬙ or caller id on certain radios. Operation voice commands can be used to operate the uconnect 威 phone and to navigate through the uconnect 威 phone menu structure. Voice commands are required after most uconnect...

  • Page 99

    To activate the uconnect 威 phone from idle, simply press the phone button and follow the audible prompts for directions. All uconnect 威 phone sessions begin with a press of the phone button on the radio control head. Cancel command at any prompt, after the beep, you can say ⬙cancel⬙ and you will be ...

  • Page 100

    • you will then be asked to give your cellular phone a priority level between one and seven, with one being the highest priority. You can pair up to seven cellular phones to your uconnect 威 phone. However, at any given time, only one cellular phone can be in use, connected to your uconnect 威 phone. ...

  • Page 101

    Or downloaded phonebook. To learn how to store a name in the phonebook, refer to ⬙add names to your uconnect 威 phonebook,⬙ in the phonebook. • the uconnect威 system will confirm the name and then dial the corresponding phone number, which may appear in the display of certain radios. Add names to your...

  • Page 102

    Phonebook download – automatic phonebook transfer from cellular phone if equipped and specifically supported by your phone, uconnect 威 phone automatically downloads names (text names) and number entries from the cellular phone’s phonebook. Specific bluetooth 威 phones with phone book access profile m...

  • Page 103

    Phonebook download — single entry if equipped and supported by your phone, uconnect 威 phone allows the user to download entries from their phone via bluetooth 威. To use this feature, press the phone button and say “phonebook download.” the system prompts, “ready to accept “v” card entry via bluetoot...

  • Page 104

    • you will then be asked for the name of the phonebook entry that you wish to edit. • next, choose the number designation (home, work, cellular, or pager) that you wish to edit. • when prompted, recite the new phone number for the phonebook entry that you are editing. After you are finished editing ...

  • Page 105

    • after you enter the name, the uconnect威 phone will ask you which designation you wish to delete: home, work, cellular, pager, or all. Say the designation you wish to delete. • note that only the phonebook entry in the current language is deleted. • automatic downloaded phonebook entries cannot be ...

  • Page 106

    • the uconnect威 phone will then prompt you as to the number designation you wish to call. • the selected number will be dialed. Phone call features the following features can be accessed through the uconnect 威 phone if the feature(s) are available on your cellular service plan. For example, if your ...

  • Page 107

    Making a second call while current call is in progress to make a second call while you are currently on a call, press the voice recognition button and say ⬙dial⬙ or ⬙call⬙ followed by the phone number or phonebook entry you wish to call. The first call will be on hold while the second call is in pro...

  • Page 108

    Call termination to end a call in progress, momentarily press the phone button. Only the active call(s) will be terminated and if there is a call on hold, it will become the new active call. If the active call is terminated by the far end, a call on hold may not become active automatically. This is ...

  • Page 109

    Uconnect 姞 phone features language selection to change the language that the uconnect 威 phone is using: • press the phone button to begin. • after the ⬙ready⬙ prompt and the following beep, say the name of the language you wish to switch to english, espanol, or francais. • continue to follow the sys...

  • Page 110

    Canada and 060 for mexico). The number dialed may not be applicable with the available cellular service and area. • if supported, this number may be programmable on some systems. To do this, press the phone button and say ‘setup’, followed by ‘emergency’. • the uconnect威 phone does slightly lower yo...

  • Page 111

    Paging to learn how to page, refer to ⬙working with automated systems. ⬙ paging works properly except for pagers of certain companies, which time out a little too soon to work properly with the uconnect 威 phone. Voice mail calling to learn how to access your voice mail, refer to ⬙working with automa...

  • Page 112

    Send the corresponding phone number associated with the phonebook entry, as tones over the phone. Note: • you may not hear all of the tones due to cellular phone network configurations. This is normal. • some paging and voice mail systems have system time out settings that are too short and may not ...

  • Page 113

    Dialing using the cellular phone keypad you can dial a phone number with your cellular phone keypad and still use the uconnect 威 phone (while dialing via the cellular phone keypad, the user must exercise caution and take precautionary safety measures). By dialing a number with your paired bluetooth ...

  • Page 114

    Advanced phone connectivity transfer call to and from cellular phone the uconnect 威 phone allows ongoing calls to be trans- ferred from your cellular phone to the uconnect 威 phone without terminating the call. To transfer an ongoing call from your uconnect 威 phone paired cellular phone to the uconne...

  • Page 115

    Select another cellular phone this feature allows you to select and start using another phone paired with the uconnect 威 phone. • press the phone button to begin. • after the ⬙ready⬙ prompt and the following beep, say ⬙setup select phone⬙ and follow the prompts. • you can also press the voice recogn...

  • Page 116

    Voice training for users experiencing difficulty with the system recog- nizing their voice commands or numbers, the uconnect 威 phone voice training feature may be used. To enter this training mode, follow one of the two following proce- dures: from outside the uconnect 威 phone mode (e.G., from radio...

  • Page 117

    • performance is maximized under: • low-to-medium blower setting, • low-to-medium vehicle speed, • low road noise, • smooth road surface, • fully closed windows, • dry weather condition. • even though the system is designed for users speaking in north american english, french, and spanish ac- cents,...

  • Page 118

    Far end audio performance • audio quality is maximized under: • low-to-medium blower setting, • low-to-medium vehicle speed, • low road noise, • smooth road surface, • fully closed windows, • dry weather conditions, and • operation from the driver’s seat. • performance, such as audio clarity, echo, ...

  • Page 119

    Understanding the features of your vehicle 117 3.

  • Page 120

    118 understanding the features of your vehicle.

  • Page 121

    Understanding the features of your vehicle 119 3.

  • Page 122

    Voice commands primary alternate(s) zero one two three four five six seven eight nine star (*) plus (+) pound (#) add location all voice commands primary alternate(s) call cancel confirmation prompts continue delete dial download edit emergency english erase all espanol francais help home 120 unders...

  • Page 123

    Voice commands primary alternate(s) language list names list phones mobile mute mute off new entry no pager pair a phone phone pairing pairing phonebook phone book previous record again redial voice commands primary alternate(s) return to main menu return or main menu select phone select send set up...

  • Page 124

    General information this device complies with part 15 of the fcc rules and rss 210 of industry canada. Operation is subject to the following conditions: • changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment....

  • Page 125

    When you press the vr button, you will hear a beep. The beep is your signal to give a command. Note: if you do not say a command within a few seconds, the system will present you with a list of options. If you ever wish to interrupt the system while it lists options, press the vr button, listen for ...

  • Page 126

    Commands the voice recognition (vr) system understands two types of commands. Universal commands are available at all times. Local commands are available if the supported radio mode is active. Changing the volume 1. Start a dialogue by pressing the vr button. 2. Say a command (e.G., “help”). 3. Use ...

  • Page 127

    Radio fm to switch to the fm band, say “fm” or “radio fm”. In this mode, you may say the following commands: • “frequency” (to change the frequency) • “next station” (to select the next station) • “previous station” (to select the previous station) • “radio menu” (to switch to the radio menu) • “mai...

  • Page 128

    Memo to switch to the voice recorder mode, say “memo”. In this mode, you may say the following commands: • “new memo” (to record a new memo) — during the recording, you may press the vr button to stop recording. You proceed by saying one of the following commands: − “save” (to save the memo) − “cont...

  • Page 129

    Note: keep in mind that you have to press the vr button first and wait for the beep before speaking the “barge in” commands. Voice training for users experiencing difficulty with the system recog- nizing their voice commands or numbers, uconnect 威 phone voice training feature may be used. 1. Press t...

  • Page 130

    Desired. Then, using body pressure, move forward and rearward on the seat to be sure that the seat adjusters have latched. Warning! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted...

  • Page 131

    Warning! • adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust the seat only while the vehicle is parked. • do not ride with the seatback reclined so ...

  • Page 132

    Power seat — if equipped the power seat switch is on the outboard side of the seat near the floor. For vehicles equipped with a power driver’s seat, use this switch to move the seat up, down, forward, rearward, or to tilt the seat. For vehicles equipped with a power passenger seat, use this switch t...

  • Page 133

    Head restraints head restraints can reduce the risk of whiplash injury in the event of a rear impact. Adjust the head restraints so that the upper edge is as high as practical. The head restraints have a locking button that must be pushed inward to lower the head restraint. However, the head restrai...

  • Page 134

    Heated seats — if equipped this feature heats both the front driver and passenger seats. The controls for the front heated seats are located on the instrument panel below the climate controls. After turning the ignition on, you can choose from high, low, or off heat settings. Amber indicator lights ...

  • Page 135

    Note: when a heat setting is selected, heat will be felt within two to five minutes. Warning! • persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, ex- haustion or other physical condition must exercise care...

  • Page 136

    Warning! (continued) • do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • be sure everyone in your vehicle is in a seat and using a seat belt properly. To lower the rear seat 1. Locate the release strap on the lower outboard side of each rear se...

  • Page 137

    To raise the rear seat note: if interference from the cargo area prevents the seatback from fully locking, you will have difficulty returning the seat to its proper position. 1. If locked in the folded position, pull the release strap (toward the front of the vehicle). 2. Raise the seatback and lock...

  • Page 138

    Driver memory seat — if equipped this feature allows the driver to store up to two different memory profiles, for easy recall through a memory switch. Each memory profile contains desired position settings for the driver seat and side mirrors, and a set of desired radio station presets. The memory s...

  • Page 139

    2. Adjust all memory profile settings to desired prefer- ences (i.E., seat, side mirror, and radio station presets). 3. Press and release the set (s) button on the memory switch, then press the side of the rocker switch labeled (1) within five seconds. The electronic vehicle information center (evic...

  • Page 140

    Linking and unlinking the remote keyless entry transmitter to memory your remote keyless entry (rke) transmitters can be programmed to recall one of two pre-programmed memory profiles with a press of the unlock button on the rke transmitter. To program your rke transmitters, perform the follow- ing:...

  • Page 141

    To recall the memory settings for driver one, press memory button number 1 or the unlock button on the rke transmitter linked to memory position 1. To recall the memory setting for driver two, press memory button number 2 or the unlock button on the rke transmitter linked to memory position 2. A rec...

  • Page 142

    • the easy entry/easy exit feature is disabled when the driver’s seat position is less than 0.9 in (23 mm) forward of the rear stop. At this position, there is no benefit to the driver by moving the seat for easy exit or easy entry. Each stored memory setting will have an associated easy entry and e...

  • Page 143

    Use the hood prop rod to secure the hood in the open position. Place the upper end of the prop rod in the hole on the underside of the hood. Underhood safety latch hood prop rod hole location understanding the features of your vehicle 141 3.

  • Page 144

    Caution! To prevent possible damage: • before closing hood, make sure the hood prop rod is fully seated into its storage retaining clips. • do not slam the hood to close it. Use a firm downward push at the center front edge of the hood to ensure that both latches engage. • never drive your vehicle u...

  • Page 145

    Headlights and parking lights turn the end of the multifunction lever to the first detent for parking light operation. Turn the end of the lever to the second detent for headlight operation. Automatic headlights — if equipped this system automatically turns the headlights on or off according to ambi...

  • Page 146

    In addition, the headlights will turn off when the wipers are turned off if they were turned on by this feature. The headlights with wipers feature can be turned on or off through the electronic vehicle information center (evic) — if equipped. For details, refer to ”headlights on with wipers,” under...

  • Page 147

    Note: the daytime running lights will turn off automatically when the turn signal is in operation and turn on again when the turn signal is not operating. Lights-on reminder if the headlights or parking lights are on after the ignition is turned to the lock position, a chime will sound to alert the ...

  • Page 148

    Turn signals move the multifunction lever upward or downward and the corresponding turn signal indicator on the instru- ment panel will flash to show proper operation of the front and rear turn signal lights. You can signal a lane change by moving the multifunc- tion lever upward or downward partial...

  • Page 149

    High beam/low beam select switch push the multifunction lever away from you to switch the headlights to high beam. Pull the multifunction lever toward you, to switch the headlights back to low beam. Flash-to-pass you can signal another vehicle with your headlights by lightly pulling the multifunctio...

  • Page 150

    Cargo light the cargo light is mounted in the headliner above the rear cargo area. This light will turn on when you open the liftgate or any door, or if you press the unlock button on the rke transmitter, or rotate the dimmer control on the multifunction lever completely upward to the second detent....

  • Page 151

    Parade mode (daytime brightness feature) rotate the dimmer control to the first detent to brighten the odometer and radio display when the parking lights or headlights are on during daylight conditions. Interior light on rotate the dimmer control completely upward to the second detent to turn on the...

  • Page 152

    They are operating. The wipers will resume operation when you turn the ignition switch to the on position again. Caution! • turn the windshield wipers off when driving through an automatic car wash. Damage to the windshield wipers may result if the wiper control is left in any position other than of...

  • Page 153

    Second to a maximum of approximately 18 seconds between cycles at vehicle speeds greater than 10 mph (16 km/h). Warning! Sudden loss of visibility through the windshield could lead to an accident. You might not see other vehicles or other obstacles. To avoid sudden icing of the windshield during fre...

  • Page 154

    Headlights with wipers (available with auto headlights only) when this feature is active, the headlights will turn on approximately 10 seconds after the wipers are turned on if the multifunction lever (on the left side of the steering column) is placed in the auto position. In addition, the headligh...

  • Page 155

    • use of rain-x威 or products containing wax or silicone may reduce rain sensor performance. • the rain-sensing feature can be turned on and off through the electronic vehicle information center (evic) — if equipped. For details, refer to “personal settings (customer-programmable features)” under “el...

  • Page 156

    Windshield washers to use the washer, pull the windshield wiper/washer control lever toward you and hold it for as long as washer spray is desired. If you activate the washer while the wiper control is in the delay range, the wipers will operate in low-speed for two wipe cycles after releasing the l...

  • Page 157

    Warning! Do not adjust the steering wheel while driving. The tilt adjustment must be locked while driving. Adjust- ing the steering wheel while driving or driving without the tilt adjustment locked could cause the driver to lose control of the vehicle. Electronic speed control — if equipped when eng...

  • Page 158

    Simultaneously. If this occurs, the electronic speed con- trol system can be reactivated by pushing the electronic speed control on/off button and resetting the desired vehicle set speed. To activate push and release the on/off button located on the end of the electronic speed control lever. The cru...

  • Page 159

    To deactivate a soft tap on the brake pedal, or pulling the electronic speed control lever toward you (cancel), or normal brake or clutch pressure while slowing the vehicle will deacti- vate the speed control without erasing the set speed from memory. Pressing the on/off button or turning off the ig...

  • Page 160

    To accelerate for passing press the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed. Using electronic speed control on hills note: the electronic speed control system maintains speed up and down hills. A slight speed change on moderate hills is...

  • Page 161

    System usage precautions note: • ensure that the rear bumper is free of dirt and debris to keep the rear park assist system operating prop- erly. • jackhammers, large trucks, and other vibrations could affect the performance of the rear park assist system. • when you turn off the rear park assist sy...

  • Page 162

    Caution! (continued) • the vehicle must be driven slowly when using the rear park assist system to be able to stop in time when the obstacle is detected. It is recommended that the driver looks over his/her shoulder when using the rear park assist system. • clean the rear park assist sensors with wa...

  • Page 163

    Warning! (continued) • before using the rear park assist system, it is strongly recommended that the ball mount and hitch ball assembly is disconnected from the ve- hicle when the vehicle is not used for towing. Failure to do so can result in injury or damage to vehicles or obstacles because the hit...

  • Page 164

    Vehicles equipped with rear park assist switch you can turn the rear park assist system on or off by pressing the rear park assist switch located the lower switch bank below the climate controls. System operation the system uses four sensors located in the rear bumper fascia to scan for obstacles up...

  • Page 165

    The warning display contains two sets of yellow and red leds, one set to warn of obstacles behind the left rear of the vehicle and the other set to warn of obstacles behind the right rear of the vehicle. The driver can view the leds either through the rear view mirror or by looking at the display ab...

  • Page 166

    Warning display distances display led obstacle distance from: led color audible signal rear corners rear center inner led 79 in (200 cm) yellow sounds for 1 ⁄ 2 second 1st led 51 in (130 cm) yellow none 2nd led 45 in (115 cm) yellow none 3rd led 31.5 in (80 cm) 39 in (100 cm) yellow none 4th led 25....

  • Page 167

    Garage door opener — if equipped homelink 威 replaces up to three remote controls (hand- held transmitters) that operate devices such as garage door openers, motorized gates, lighting, or home security systems. The homelink 威 unit operates off your vehicle’s battery. The homelink 威 buttons that are l...

  • Page 168

    Warning! • your motorized door or gate will open and close while you are training the universal transceiver. Do not train the transceiver if people or pets are in the path of the door or gate. Only use this trans- ceiver with a garage door opener that has a “stop and reverse” feature as required by ...

  • Page 169

    Place the hand-held transmitter 1–3 in (3-8 cm) away from the homelink 威 button you wish to program while keeping the indicator light in view. 3. Simultaneously press and hold both the chosen homelink 威 button and the hand-held transmitter button until the homelink 威 indicator changes from a slow to...

  • Page 170

    This can usually be found where the hanging antenna wire is attached to the garage door opener motor (it is not the button normally used to open and close the door). 6. Firmly press and release the “learn” or “training” button. The name and color of the button may vary by manufacturer. Note: there a...

  • Page 171

    Gate operator/canadian programming canadian radio-frequency laws require transmitter sig- nals to “time-out” (or quit) after several seconds of transmission – which may not be long enough for homelink 威 to pick up the signal during programming. Similar to this canadian law, some u.S. Gate operators ...

  • Page 172

    Reprogramming a single homelink 姞 button to re-program a channel that has been previously trained, follow these steps: 1. Turn the ignition switch to the on/run position. 2. Press and hold the desired homelink 威 button until the indicator light begins to flash after 20 seconds. Do not release the bu...

  • Page 173

    General information this device complies with fcc rules part 15 and industry canada rss-210. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference that may be received including interference that may cause...

  • Page 174

    Warning! • never leave unattended children in a vehicle with the key in the ignition switch. Occupants, particu- larly unattended children, can become entrapped by the power sunroof while operating the power sunroof switch. Such entrapment may result in serious injury or death. • in an accident, the...

  • Page 175

    Position. The sunroof will close fully and stop automati- cally. This is called “express close”. During express close operation, any movement of the switch will stop the sunroof. Closing sunroof — manual mode to close the sunroof, press and hold the switch in the forward position. Any release of the...

  • Page 176

    Wind buffeting wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions. This is a normal occur- rence and ...

  • Page 177

    Sky slider 姞 usage precautions note: • the system will not operate when ambient tempera- ture is at –4°f (–20°c) or lower. • the system will not operate at vehicle speeds of 86 mph (138 km/h) or above. • opening and closing the sky slider威 repeatedly with- out the engine running may run the battery ...

  • Page 178

    Warning! Failure to follow these warnings can result in injuries that are serious or fatal to you, your passengers, and others around you: • in an accident, there is a greater risk of being thrown from a vehicle with the sky slider 威 open. Always fasten your seat belt properly and make sure all pass...

  • Page 179

    Sky slider 姞 control the sky slider 威 switch is located between the sun visors on the overhead console. Note: the sky slider 威 switch will operate when the ignition switch is turned to the on position. Opening the sky slider 姞 using automatic mode press the switch rearward and release it within one-...

  • Page 180

    Using operator mode press the switch rearward and hold it, the sky slider 威 will open from the front and move toward the rear of the vehicle. Press the switch forward and hold it, the sky slider 威 will open from the rear and move toward the front of the vehicle. Note: during operation, any movement ...

  • Page 181

    Completely. The left motor facing forward will close the top when it is open from the rear of the vehicle. The right motor will close the top when it is open from the front of the vehicle. Anti-pinch protect feature the sky slider 威 will retract automatically if it detects an obstruction while closi...

  • Page 182

    Electrical power outlet your vehicle is equipped with a fused 12-volt (dc) power outlet. This power outlet is located on the instrument panel, below the climate controls. It has power available when the ignition switch is in the on or acc position. Insert the cigar lighter or accessory plug into the...

  • Page 183

    Caution! • many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.E., cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting. • ac...

  • Page 184

    Power inverter — if equipped your vehicle may be equipped with a 115-volt ac (150 watt maximum) power outlet located on the back of the center console. This outlet can power cellular phones, electronics and other low power devices requiring power up to 150 watts. Certain high-end video games, such a...

  • Page 185

    Press and release the switch once to turn on the power outlet. A status indicator in the switch will illuminate in approximately one second to indicate that power is available at the outlet. Press and release the switch again to turn off the power outlet. The status indicator will also turn off. Not...

  • Page 186

    Cupholders there are two cupholders for the front seat passengers, located in the center console. The rear passengers have cupholders at the rear of the center console. Front cupholders rear cupholders 184 understanding the features of your vehicle.

  • Page 187

    Storage front storage compartment the front storage compartment (located on the left side of the instrument panel) can hold cell phones, pdas, and other small items. Console storage compartment to open, press the latch and lift the cover. Front storage compartment center console understanding the fe...

  • Page 188

    The center console has a removable storage tray which can hold cell phones, pdas, and other small items. Cargo area features cargo load floor the cargo load floor system has a load capacity of 400 lbs (181 kg). The load floor has a built-in storage bin that can hold a variety of items. The underside...

  • Page 189

    1. Flip the spring-loaded latch pull-loops up. 2. Pull the loops upward and twist them one-quarter turn so that they are parallel to the slots in the storage bin cover. 3. Lift the cover upward over the loops. 4. Reinstall the cover with the handle recess facing toward you. Note: you can install the...

  • Page 190

    Cargo tie-down hooks and loops the tie-downs located on cargo area floor should be used to secure loads safely when the vehicle is moving. Cargo tie-down loops are located on the trim panels. Cargo tie-down hooks cargo tie-down loops 188 understanding the features of your vehicle.

  • Page 191

    Warning! • cargo tie-downs are not safe anchors for a child seat tether strap. In a sudden stop or collision, a tie-down could pull loose and allow the child seat to come loose. A child could be badly injured. Use only the anchors provided for child seat tethers. • to help protect against personal i...

  • Page 192

    Warning! (continued) • do not pile luggage or cargo higher than the top of the seatback. This could impair visibility or be- come a dangerous projectile in a sudden stop or collision. Retractable cargo area cover — if equipped note: the purpose of this cover is for privacy, not to secure loads. It w...

  • Page 193

    Then, insert the spring-loaded post on the opposite end of the cover housing into the attachment point on the opposite side of the vehicle. Next, grab the cover handle and pull the cover toward you. As the cover nears the liftgate opening, guide the rear attachment posts (on both ends of the cover) ...

  • Page 194

    Warning! In an accident, a cargo cover loose in the vehicle could cause injury. It could fly around in a sudden stop and strike someone in the vehicle. Do not store the cargo cover on the cargo floor or in the passenger compartment. Remove the cover from the vehicle when taken from its mounting. Do ...

  • Page 195

    Switch. Once released, the wiper will cycle three times, return to the park position, and then resume normal operation. Note: the rear wiper will automatically return to the park position if you turn off the ignition switch while it is operating. The rear wiper will resume operation when you turn th...

  • Page 196

    Defroster automatically turns off after approximately 10 minutes. For an additional five minutes of operation, press the button a second time. Note: to prevent excessive battery drain, use the rear window defroster only when the engine is operating. Caution! Failure to follow these cautions can caus...

  • Page 197

    External racks do not increase the total load carrying capacity of the vehicle. Be sure that the total occupant and luggage load inside the vehicle, plus the load on the luggage rack, do not exceed the maximum vehicle load capacity. Caution! • to avoid damage to the roof rack and vehicle, do not exc...

  • Page 199: Contents

    Understanding your instrument panel contents 䡵 instrument panel features . . . . . . . . . . . . . . . 200 䡵 instrument cluster . . . . . . . . . . . . . . . . . . . . 201 䡵 instrument cluster descriptions . . . . . . . . . . . 202 䡵 electronic vehicle information center (evic) — if equipped . . . ....

  • Page 200

    ▫ info button (disc mode for mp3/wma play) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 240 䡵 am/fm/cd/dvd radio (rer/ren) – if equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . . 243 ▫ operating instructions — voice recognition system (vr) — if equipped . . . . . . . . . ....

  • Page 201

    ▫ electronic serial number/sirius identification number (esn/sid) . . . . . . . . . 266 ▫ selecting uconnect威 studios (satellite) mode . . . . . . . . . . . . . . . . . . . . . 267 ▫ satellite antenna . . . . . . . . . . . . . . . . . . . . . 267 ▫ reception quality . . . . . . . . . . . . . . . . ....

  • Page 202

    Instrument panel features 1 — air outlet 4 — radio 7 — power outlet 2 — instrument cluster 5 — glove compartment 8 — lower switch bank 3 — storage tray 6 — climate control 9 — storage bin (if equipped) 200 understanding your instrument panel.

  • Page 203

    Instrument cluster understanding your instrument panel 201 4.

  • Page 204

    Instrument cluster descriptions 1. Fuel gauge the fuel gauge shows level of fuel in tank when ignition switch is in the on position. 2. Fuel door reminder this symbol indicates the side of the vehicle where the fuel cap is located. 3. Low fuel light this indicator lights when the fuel level drops to...

  • Page 205

    Maintain correct tire pressure, even if under-inflation has not reached the level to trigger illumination of the tpms low tire pressure telltale. Your vehicle has also been equipped with a tpms malfunction indicator to indicate when the system is not operating properly. The tpms malfunction indicato...

  • Page 206

    5. Electronic throttle control (etc) light this light informs you of a problem with the electronic throttle control (etc) system. If a problem is detected, the light will come on while the engine is running. Cycle the ignition key when the vehicle has completely stopped and the shift lever is placed...

  • Page 207

    7. High beam indicator this indicator shows that the high beam head- lights are on. Pull the multifunction control lever on the left side of the steering column toward you to switch to low beam. 8. Front fog light indicator — if equipped this indicator will illuminate when the fog lights are on. 9. ...

  • Page 208

    The charging system light remains on, it means that the vehicle is experiencing a problem with the charging system. Obtain service immediately. See an autho- rized dealer. 13. Oil pressure warning light this light indicates low engine oil pressure. The light should turn on momentarily when the engin...

  • Page 209

    15. Tachometer this gauge measures engine revolutions-per-minute (rpm x 1000). Before the pointer reaches the red area, ease up on the accelerator to prevent engine damage. 16. 4wd low indicator — if equipped this light alerts the driver that the vehicle is in the 4wd low mode. In this mode, the fro...

  • Page 210

    20. Electronic stability program (esp) / brake assist system (bas) indicator light – if equipped the malfunction indicator for the electronic stability program (esp) is combined with the brake assist system (bas). The yellow “esp/ bas warning light” in the instrument cluster comes on when the igniti...

  • Page 211

    If the light turns on while driving, safely pull over and stop the vehicle. If the a/c system is on, turn it off. Also, shift the transmission into neutral and idle the ve- hicle. If the temperature reading does not return to normal, turn the engine off immediately and call for service. Refer to “if...

  • Page 212

    Warning! A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant. You may want to call an authorized dealer- ship for service if your vehicle overheats. If you decide to look under the hood yourself, see section 7 of this manual. Follow the warnings ...

  • Page 213

    26. 4wd indicator — vehicles equipped with selec-trac 威 ii this light alerts the driver that the vehicle is in the full-time four-wheel drive auto mode. In this mode, the system operates with a normal torque split of 42% front axle and 58% rear axle. It can redirect up to 100% of torque to the front...

  • Page 214

    Fuel cap fault message if the vehicle diagnostic system determines that the fuel filler cap is loose, improperly installed, or damaged, the words “gascap” will display in the odometer. If this occurs, tighten the fuel filler cap properly and press the odometer reset button to turn off the message. I...

  • Page 215

    28. Cruise indicator — if equipped this indicator lights when the electronic speed control system is turned on. 29. Shift lever indicator this display indicator shows automatic transmission shift lever selection. 30. Seat belt reminder light this light will turn on for several seconds after the igni...

  • Page 216

    Note: the light may flash momentarily during sharp cornering maneuvers, which change fluid level condi- tions. The vehicle should have service performed, and the brake fluid level checked. If brake failure is indicated, immediate repair is neces- sary. Warning! Driving a vehicle with the red brake l...

  • Page 217

    33. Airbag warning light this light turns on and remains on for six to eight seconds as a bulb check when the ignition switch is first turned on. If the light does not turn on during starting, stays on, or turns on while driving, have the system checked by an authorized dealer. 34. Electronic vehicl...

  • Page 218

    This system conveniently allows the driver to select a variety of useful information by pressing the switches mounted on the steering wheel. The evic consists of the following: • system status • vehicle information warning message displays • tire pressure monitor system (if equipped) • personal sett...

  • Page 219

    Press the function select button to accept a selection. Electronic vehicle information center (evic) displays when the appropriate conditions exist, the evic displays the following messages. • turn signal on (with a continuous warning chime) • left front turn signal light out (with a single chime) •...

  • Page 220

    • left/right rear door ajar (one or more, with a single chime if speed is above 1 mph(1.6 km/h)) • door(s) ajar (with a single chime if vehicle is in motion) • liftgate ajar (with a single chime) • left front low pressure (with a single chime). Refer to “tire pressure monitoring system” in section 5...

  • Page 221

    Unless reset, this message will continue to display each time you turn the ignition switch to the on position. To turn off the message temporarily, press and release the menu button. To reset the oil change indicator system (after performing the scheduled maintenance) perform the following procedure...

  • Page 222

    • distance to empty (dte) shows the estimated distance that can be traveled with the fuel remaining in the tank. This estimated distance is determined by a weighted average of the instantaneous and average fuel economy, according to the current fuel tank level. Dte cannot be reset through the functi...

  • Page 223

    Compass display the compass readings indicate the direction the vehicle is facing. Press and release the compass button to display one of eight com- pass readings and the outside temperature. Automatic compass calibration this compass is self-calibrating, which eliminates the need to set the compass...

  • Page 224

    5. Complete one or more 360–degree turns (in an area free from large metal or metallic objects) until the “cal” indicator turns off. The compass will now function normally. Compass variance compass variance is the difference between magnetic north and geographic north. To compensate for the differen...

  • Page 225

    4. Press and release function select button until the proper variance zone is selected according to the map. 5. Press and release the compass button to exit. Personal settings (customer-programmable features) personal settings allows the driver to set and recall features when the vehicle speed is at...

  • Page 226

    Remote key unlock when driver door 1st press is selected, only the driver’s door will unlock on the first press of the remote keyless entry (rke) transmitter unlock button. When driver door 1st press is selected, you must press the rke transmitter unlock button twice to unlock the passen- ger’s door...

  • Page 227

    Automatically move seat back on exit — if equipped this feature provides automatic driver seat positioning to enhance driver mobility when entering and exiting the vehicle. To make your selection, press and release the function select button until “on” or “off” appears. Note: the seat will return to...

  • Page 228

    Delay turning headlights off when this feature is selected, the driver can choose to have the headlights remain on for 0, 30, 60, or 90 seconds when exiting the vehicle. To make your selection, press and release the function select button until “0,” “30,” “60,” or “90” appears. Turn headlights on wi...

  • Page 229

    Hill start assist (hsa) — if equipped when on is selected, the hsa system is active. Refer to “hsa (hill start assist)” under “electronic brake control system” in section 5 of this manual for system function and operating information. To make your selection, press and release the function select but...

  • Page 230

    Power switch/volume control (rotary) push the on/volume control knob to turn on the radio. Press the on/volume control knob a second time to turn off the radio. Electronic volume control the electronic volume control turns continuously (360 degrees) in either direction without stopping. Turning the ...

  • Page 231

    If your vehicle is not equipped with or this feature is not available on your vehicle, a “not equipped with uconnect” message will display on the radio screen. Time button press the time button to alternate locations of the time and frequency display. Clock setting procedure 1. Press and hold the ti...

  • Page 232

    Setting the tone, balance, and fade push the rotary tune/scroll control knob and bass will display. Turn the tune/scroll control knob to the right or left to increase or decrease the bass tones. Push the rotary tune/scroll control knob a second time and mid will display. Turn the tune/scroll control...

  • Page 233

    Toggle the music type button to select the following format types: program type 16-digit character display no program type or un- defined none adult hits adlt hit classical classicl classic rock cls rock college college country country foreign language language information inform jazz jazz news news...

  • Page 234

    By pressing the seek button when the music type icon is displayed, the radio will be tuned to the next frequency station with the same selected music type name. The music type function only operates when in the fm mode. If a preset button is activated while in the music type (program type) mode, the...

  • Page 235

    Note: • the available selections for each of the above entries varies depending upon the disc. • these selections can only be made while playing a dvd. • ves™ power - allows you to turn ves™ on and off (if equipped). • ves™ lock - locks out rear ves™ remote controls (if equipped). • ves™ ch1/ch2 - a...

  • Page 236

    Subtitle language — if equipped selecting this item allows you to choose a default subtitle language (effective only if the language is supported by the disc). You can select a language not listed by scrolling down and selecting ⬙other.⬙ enter the country code using the tune/scroll control knob to s...

  • Page 237

    Set button — to set the pushbutton memory when you are receiving a station that you wish to commit to pushbutton memory, press the set button. The symbol set 1 will now show in the display window. Select the button (1-6) you wish to lock onto this station and press and release that button. If a butt...

  • Page 238

    Caution! The radio may shut down during extremely hot conditions. When this occurs, the radio will indicate “disc hot” and shut off until a safe temperature is reached. This shutdown is necessary to protect the optics of the dvd player and other radio internal components. Note: the ignition switch m...

  • Page 239

    Eject button — ejecting compact disc(s) press the eject button and the pushbutton with the corresponding number (1-6) where the cd was loaded and the disc will unload and move to the entrance for easy removal. Radio display will show ⬙ejecting disc⬙ when the disc is being ejected and prompt the user...

  • Page 240

    Notes on playing mp3/wma files the radio can play mp3/wma files; however, acceptable mp3/wma file recording media and formats are limited. When writing mp3/wma files, pay attention to the following restrictions. Supported media (disc types) the mp3/wma file recording media supported by the radio are...

  • Page 241

    If a disc contains multi-formats, such as cd audio and mp3/wma tracks, the radio will only play the mp3/ wma tracks on that disc. Supported mp3/wma file formats the radio will recognize only files with the *.Mp3/wma extension as mp3/wma files. Non-mp3/wma files named with the *.Mp3/wma extension may...

  • Page 242

    Playback of mp3/wma files when a medium containing mp3/wma data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the mp3/wma files. Loading times for playback of mp3/wma files may be affected by the ...

  • Page 243

    Press and hold the info button again for three seconds to return to ⬙elapsed time⬙ display. Operation instructions - auxiliary mode the auxiliary (aux) jack is an audio input jack which allows the user to plug in a portable device such as an mp3/wma player, cassette player, or microphone and utilize...

  • Page 244

    Operating instructions — voice recognition system (vr) (if equipped) for the radio, refer to “voice recognition system (vr)” in section 3. For uconnect 威 “voice recognition system (vr),” refer to “uconnect 威 phone” in section 3. Operating instructions - uconnect 威 phone (if equipped) refer to “uconn...

  • Page 245

    Am/fm/cd/dvd radio (rer/ren) – if equipped note: the sales code is located on the lower right side of the unit’s faceplate. The ren and rer radios contain a cd/dvd player, usb port, and a 30-gigabyte hard drive (hdd). Sirius satellite radio is optional. The 6.5 in (16.5 cm) touch screen allows for e...

  • Page 246

    4. To move the hour forward, touch the screen where the word “hour” with the arrow pointing upward is dis- played. To move the hour backward, touch the screen where the word “hour” with the arrow pointing down- ward is displayed. 5. To move the minute forward, touch the screen where the word “min” w...

  • Page 247

    Changing the time zone 1. Turn on the radio. 2. Touch the screen where the time is displayed. The clock setting menu will appear on the screen. 3. Touch the screen where the words “set time zone” are displayed. The time zone selection menu will appear on the screen. 4. Select a time zone by touching...

  • Page 248

    Operating instructions — radio mode note: the ignition switch must be in the on or acc position to operate the radio. Power switch/volume control (rotary) push the on/volume control knob to turn on the radio. Push the on/volume control knob a second time to turn off the radio. Electronic volume cont...

  • Page 249

    5. To exit, press any button/knob, or wait five seconds. Rw/ff pressing the rw (rewind) or ff (fast forward) buttons causes the tuner to search for the next frequency in the direction of the arrows. This feature operates in either am or fm frequencies. Tune control turn the rotary tune/scroll contro...

  • Page 250

    Set/rnd button — to set the pushbutton memory when you are receiving a station that you wish to commit to pushbutton memory, press the set/rnd button. The symbol set 1 will now show in the display window. Select the button (1 to 6) you wish to lock onto this station and press and release that button...

  • Page 251

    Operation instructions — cd mode for cd and mp3 audio play note: • the ignition switch must be in the on or acc position to operate the radio. • this radio is capable of playing compact discs (cd), recordable compact discs (cd-r), rewritable compact discs (cd-rw), compact discs with mp3 tracks and m...

  • Page 252

    Eject button - ejecting a cd press the eject button to eject the cd. If you have ejected a disc and have not removed it within 10 seconds, it will be reloaded. If the cd is not removed, the radio will reinsert the cd but will not play it. A disc can be ejected with the radio and ignition off. Note: ...

  • Page 253

    Press the rnd button a second time to stop random play. Notes on playing mp3 files the radio can play mp3 files; however, acceptable mp3 file recording media and formats are limited. When writing mp3 files, pay attention to the following restric- tions. Supported media (disc types) the mp3 file reco...

  • Page 254

    Multisession disc formats are supported by the radio. Multisession discs may contain combinations of normal cd audio tracks and computer files (including mp3 files). Discs created with an option such as ⬙keep disc open after writing ⬙ are most likely multisession discs. The use of multisession for c...

  • Page 255

    Playback of mp3 files when a medium containing mp3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the mp3 files. Loading times for playback of mp3 files may be affected by the following: • med...

  • Page 256

    Sales code res/rsc — am/fm stereo radio with cd player (mp3 aux jack) and sirius radio note: the radio sales code is located on the lower right side of the radio faceplate. Operating instructions — radio mode note: the ignition switch must be in the on or acc position to operate the radio. Power swi...

  • Page 257

    Seek buttons press and release the seek buttons to search for the next listenable station in am/fm mode. Press the right switch to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection. Holding either button will bypass stations wit...

  • Page 258

    4. Adjust the minutes using the right side tune/ scroll control knob. Press the tune/scroll control knob to save time change. 5. To exit, press any button/knob or wait five seconds. The clock can also be set by pressing the setup button. For vehicles equipped with satellite radio, press the setup bu...

  • Page 259

    Push the rotary tune/scroll control knob a third time and treble will display. Turn the tune/scroll control knob to the right or left to increase or decrease the treble tones. Push the rotary tune/scroll control knob a fourth time and balance will display. Turn the tune/ scroll control knob to the r...

  • Page 260

    Program type 16-digit character display news news nostalgia nostalga oldies oldies personality persnlty public public rhythm and blues r & b religious music rel musc religious talk rel talk rock rock soft soft soft rock soft rck soft rhythm and blues soft r&b sports sports talk talk top 40 top 40 we...

  • Page 261

    Am/fm button press the button to select either am or fm mode. Set/rnd button — to set the pushbutton memory when you are receiving a station that you wish to commit to pushbutton memory, press the set/rnd button. The symbol set 1 will now show in the display window. Select the button (1 to 6) you wi...

  • Page 262

    Operation instructions — cd mode for cd and mp3 audio play note: • the ignition switch must be in the on or acc position to operate the radio. • this radio is capable of playing compact discs (cd), recordable compact discs (cd-r), rewritable compact discs (cd-rw), compact discs with mp3 tracks and m...

  • Page 263

    Eject button - ejecting a cd press the eject button to eject the cd. If you have ejected a disc and have not removed it within 10 seconds, it will be reloaded. If the cd is not removed, the radio will reinsert the cd but will not play it. A disc can be ejected with the radio and ignition off. Note: ...

  • Page 264

    Press the set/rnd button a second time to stop ran- dom play. Notes on playing mp3 files the radio can play mp3 files; however, acceptable mp3 file recording media and formats are limited. When writing mp3 files, pay attention to the following restric- tions. Supported media (disc types) the mp3 fil...

  • Page 265

    Multisession disc formats are supported by the radio. Multisession discs may contain combinations of normal cd audio tracks and computer files (including mp3 files). Discs created with an option such as ⬙keep disc open after writing ⬙ are most likely multisession discs. The use of multisession for c...

  • Page 266

    Playback of mp3 files when a medium containing mp3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the mp3 files. Loading times for playback of mp3 files may be affected by the following: • med...

  • Page 267

    Press and hold the info button again for three seconds to return to ⬙elapsed time⬙ display. Operation instructions - auxiliary mode the auxiliary (aux) jack is an audio input jack which allows the user to plug in a portable device such as an mp3 player or cassette player and utilize the vehicle’s au...

  • Page 268

    Uconnect 姞 studios (satellite radio) — if equipped (ren/req/rer/res/reu radios only) satellite radio uses direct satellite-to-receiver broadcast- ing technology to provide clear digital sound, coast to coast. The subscription service provider is sirius satellite radio. This service offers over 130 c...

  • Page 269

    Selected. Press the tune/scroll control knob and the sirius id number will display. The sirius id number display will time out in two minutes. Press any button on the radio to exit this screen. Esn/sid access with ren/rer radios while in sat mode, press the menu button on the radio faceplate. Next, ...

  • Page 270

    • dense tree coverage may interrupt reception in the form of short audio mutes. • driving under wide bridges or along tall buildings can cause intermittent reception. • placing objects over or too close to the antenna can cause signal blockage. Operating instructions — uconnect 姞 studios (satellite)...

  • Page 271

    Rw/ff pressing the rw (rewind) or ff (fast forward) buttons causes the tuner to search for the next channel in the direction of the arrows. Tune control (rotary) turn the rotary tune/scroll control knob clockwise to increase or counterclockwise to decrease the channel. Music type button — except reu...

  • Page 272

    Setup button pressing the setup button allows you to select the following items: • display sirius id number — press the audio/ select button to display the sirius id number. This number is used to activate, deactivate, or change the sirius subscription. Set button – to set the pushbutton memory when...

  • Page 273

    Operating instructions — uconnect 姞 phone (if equipped) refer to “uconnect 威 phone” in section 3. Operating instructions — video entertainment system (ves)™ (if equipped) refer to separate “video entertainment system (ves)™ guide.” remote sound system controls — if equipped the remote sound system c...

  • Page 274

    Right-hand switch functions • press the top of the switch to increase the volume. • press the bottom of the switch to decrease the volume. • press the button in the center of the switch to change modes (i.E., am, fm, etc.). Left-hand switch functions for radio operation • press the top of the switch...

  • Page 275

    Cd/dvd maintenance to keep a cd/dvd in good condition, take the following precautions: 1. Handle the disc by its edge; avoid touching the surface. 2. If the disc is stained, clean the surface with a soft cloth, wiping from center to edge. 3. Do not apply paper or tape to the disc; avoid scratch- ing...

  • Page 276

    Climate controls the air conditioning and heating system is designed to make you comfortable in all types of weather. Manual air conditioning and heating system the manual temperature controls consist of a series of outer rotary dials and inner pushbuttons. Blower control use this control to regulat...

  • Page 277

    Note: if your air conditioning performance seems lower than expected, check the front of the a/c con- denser (located in front of the radiator) for an accumu- lation of dirt or insects. Clean with a gentle water spray from behind the radiator and through the condenser. Fabric front fascia protectors...

  • Page 278

    • mix air is directed through the floor, defrost, and side window demist outlets. This setting works best in cold or snowy conditions that require extra heat to the windshield. This setting is good for maintaining comfort while reducing moisture on the windshield. • defrost air is directed through t...

  • Page 279

    • the a/c can be deselected manually without disturb- ing the mode control selection. Air conditioning control use this button to engage the air conditioning. A light will illuminate when the air conditioning system is engaged note: the air conditioning compressor will not engage until the engine ha...

  • Page 280

    Accomplish this, the system gathers information from the cabin infrared sensor mounted between the sun-visors and from various sensors located throughout the vehicle. The controls on the climate control provide the system with operator input. Other sensors take account of ve- hicle speed, a/c pressu...

  • Page 281

    Note: • the temperature setting can be adjusted at anytime without affecting automatic operation. • pressing the air conditioning control button while in auto mode will cause the led in the control button to flash three times and then turn off. This indicates that the system is in auto mode and requ...

  • Page 282

    280 understanding your instrument panel.

  • Page 283

    The operator can override the auto mode setting to change airflow distribution by rotating the mode control knob (on the right) to one of the following positions. • panel air is directed through the outlets in the instrument panel. These outlets can be adjusted to direct airflow. Note: the center in...

  • Page 284

    • air conditioner control press this button to turn on the air conditioning during manual operation only. When the air con- ditioning is turned on, cool dehumidified air will flow through the outlets selected with the mode control dial. Press this button a second time to turn off the air conditionin...

  • Page 285

    • most of the time, when in automatic operation, you can temporarily put the system into recirculation mode by pressing the recirculation button. However, under certain conditions, while in auto- matic mode, the system is blowing air out the defrost vents. When these conditions are present, and the ...

  • Page 286

    Window fogging interior fogging on the windshield can be quickly re- moved by turning the mode selector to defrost. The defrost/floor mode can be used to maintain a clear windshield and provide sufficient heating. If side win- dow fogging becomes a problem, increase blower speed. Vehicle windows ten...

  • Page 287

    Control setting suggestions for various weather conditions understanding your instrument panel 285 4.

  • Page 289: Starting And Operating

    Starting and operating contents 䡵 starting procedures . . . . . . . . . . . . . . . . . . . . 291 ▫ normal starting . . . . . . . . . . . . . . . . . . . . . 291 ▫ extreme cold weather (below –20°f or –29°c) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 291 ▫ if engine fails to start . . ....

  • Page 290

    䡵 off-road driving tips . . . . . . . . . . . . . . . . . . 314 ▫ when to use 4wd low range . . . . . . . . . . 314 ▫ driving through water . . . . . . . . . . . . . . . . 314 ▫ driving in snow, mud and sand . . . . . . . . . 315 ▫ hill climbing . . . . . . . . . . . . . . . . . . . . . . . 316 ▫ tr...

  • Page 291

    ▫ tire loading and tire pressure . . . . . . . . . . 342 䡵 tires — general information . . . . . . . . . . . . . 346 ▫ tire pressure . . . . . . . . . . . . . . . . . . . . . . . 346 ▫ tire inflation pressures . . . . . . . . . . . . . . . . 347 ▫ tire pressures for high speed operation . . . 349 ▫ ...

  • Page 292

    䡵 adding fuel . . . . . . . . . . . . . . . . . . . . . . . . . 370 ▫ fuel filler cap (gas cap) . . . . . . . . . . . . . . 370 ▫ loose fuel filler cap message . . . . . . . . . . . 371 䡵 vehicle loading . . . . . . . . . . . . . . . . . . . . . . 371 ▫ certification label . . . . . . . . . . . . . ...

  • Page 293

    Starting procedures before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. Warning! Do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death. Start the engine with the...

  • Page 294

    If engine fails to start warning! • never pour fuel or other flammable liquids into the throttle body air inlet opening in an attempt to start the vehicle. This could result in a flash fire causing serious personal injury. (continued) warning! (continued) • do not attempt to push or tow your vehicle...

  • Page 295

    With tip start if the engine fails to start after you have followed the “normal starting” or “extreme cold weather” proce- dures, it may be flooded. To clear any excess fuel, push the accelerator pedal all the way to the floor and hold it. Then, turn the ignition switch to the start position and rel...

  • Page 296

    Warning! Remember to disconnect the cord before driving. Damage to the 110-115 volt ac electrical cord could cause electrocution. Use the heater when temperatures below 0 °f (-18 °c) are expected to last for several days. Automatic transmission caution! Damage to the transmission may occur if the fo...

  • Page 297

    Warning! It is dangerous to move the shift lever out of park or neutral if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in reverse. You could lose control of the vehicle and hit someone or something. Only s...

  • Page 298

    5. Using the screwdriver, reach into the manual override opening. Press and hold the shift lock lever down. 6. Move the shift lever into the neutral position. 7. The vehicle may then be started in neutral. Have your vehicle inspected by your local authorized dealer if the shift lock manual override ...

  • Page 299

    Gear ranges do not race the engine when shifting from park or neutral position into another gear range. Park this range supplements the parking brake by locking the transmission. The engine can be started in this range. Never use park while the vehicle is in motion. Apply the parking brake when leav...

  • Page 300

    Warning! (continued) • it is dangerous to move the shift lever out of park or neutral if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in reverse. You could lose control of the vehicle and hit someone or som...

  • Page 301

    Overdrive operation the overdrive automatic transmission contains an elec- tronically controlled 4th speed (overdrive). The trans- mission will automatically shift from 3rd gear to over- drive if the following conditions are present: • the shift lever is in drive • the engine coolant has reached nor...

  • Page 302

    When to use tow/haul mode when driving in hilly areas, towing a trailer, carrying a heavy load, etc., and frequent transmission shifting oc- curs, press the tow/haul button. This will improve performance and reduce the potential for transmission overheating or failure due to excessive shifting. When...

  • Page 303

    Transmission limp home mode transmission function is monitored for abnormal condi- tions. If a condition is detected that could result in transmission damage, the transmission limp home mode will be engaged. In this mode, the transmission will remain in second gear in any forward driving range. To r...

  • Page 304

    Four-wheel drive operation mp1522 command-trac 姞 transfer case — if equipped operating information and precautions the command-trac 威 transfer case provides four posi- tions: • two–wheel drive (2wd) high range • four-wheel drive (4wd lock) high range • four-wheel drive (4wd low) low range • neutral ...

  • Page 305

    Caution! (continued) • the 4wd lock position and 4wd low position are intended for loose or slippery road surfaces only. Driving in these positions on dry hard- surfaced roads may cause increased tire wear and damage to the driveline components. • when operating your vehicle in 4wd low, the engine s...

  • Page 306

    Warning! (continued) • since four-wheel drive provides improved trac- tion, there is a tendency to exceed safe turning and stopping speeds. Do not go faster than road con- ditions permit. You or others could be injured. Shift positions the electronic transfer case switch is located on the center con...

  • Page 307

    4wd lock 4-wheel drive high range - this range locks the front driveshaft and rear driveshaft together forcing the front and rear wheels to rotate at the same speed. Additional traction for loose or slippery road surfaces only. 4wd low 4-wheel drive low range - this range provides low speed four-whe...

  • Page 308

    Shifting procedures note: if any of the requirements to select a new transfer case position have not been met, the transfer case will not shift, the indicator light for the previous position will remain on, and the newly selected position indicator light will continue to flash until all the requirem...

  • Page 309

    Shifting can be performed with the vehicle rolling 2 to 3 mph (3 to 5 km/h) using the “preferred procedure” or completely stopped using the “alternate procedure.” preferred procedure 1. With the engine running, slow the vehicle speed to 2 to 3 mph (3 to 5 km/h). 2. Shift the transmission into neutra...

  • Page 310

    Operable. If the ignition switch is not in the on position, then the shift will not take place and no position indicator lights will be on or flashing. Mp3022 selec-trac ii 姞 transfer case — if equipped operating information and precautions the selec-trac ii 威 active on-demand transfer case pro- vid...

  • Page 311

    Caution! (continued) • when operating your vehicle in 4wd low, the engine speed is approximately three times that of the 2wd position or 4wd auto position at a given road speed. Take care not to over-speed the engine and do not exceed 25 mph (40 km/h). • proper operation of four-wheel drive vehicles...

  • Page 312

    Warning! (continued) • since four-wheel drive provides improved trac- tion, there is a tendency to exceed safe turning and stopping speeds. Do not go faster than road con- ditions permit. You or others could be injured. Shift positions the electronic transfer case switch is located on the center con...

  • Page 313

    Wide range of conditions, while maximizing driver con- venience. This position is always in four-wheel drive mode, with a normal 42% front axle, 58% rear axle torque split. The system also anticipates and prevents slip by redirecting torque as necessary, up to 100% to the front or rear axle, if need...

  • Page 314

    Shifting procedures note: if any of the requirements to select a new transfer case position have not been met, the transfer case will not shift, the indicator light for the previous position will remain on, and the newly selected position indicator light will continue to flash until all the requirem...

  • Page 315

    Alternate procedure 1. Bring the vehicle to a complete stop. 2. With the ignition switch in the on position and the engine off or running, shift the transmission into neutral. 3. Move the 4wd control switch to the desired position. 4. After the desired position indicator light is on (not flashing), ...

  • Page 316

    Turns or abrupt maneuvers. As with other vehicles of this type, failure to operate this vehicle correctly may result in loss of control or vehicle rollover. Off-road driving tips when to use 4wd low range when off-road driving, shift to 4wd low for additional traction and control on slippery or diff...

  • Page 317

    Entering. Proceed with caution and maintain a steady controlled speed less than 5 mph (8 km/h) in deep water to minimize wave effects. Flowing water if the water is swift flowing and rising (as in storm run-off) avoid crossing until the water level recedes and/or the flow rate is reduced. If you mus...

  • Page 318

    Hill climbing note: before attempting to climb a hill, determine the conditions at the crest and/or on the other side. Before climbing a steep hill, shift the transmission to a lower gear and shift the transfer case to 4wd low. Use first gear and 4wd low for very steep hills. If you stall or begin t...

  • Page 319

    Traction downhill shift the transmission into a low gear and the transfer case to 4wd low range. Let the vehicle go slowly down the hill with all four wheels turning against engine compression drag. This will permit you to control the vehicle speed and direction. When descending mountains or hills, ...

  • Page 320

    Warning! Abrasive material in any part of the brakes may cause excessive wear or unpredictable braking. You might not have full braking power when you need it to prevent an accident. If you have been operating your vehicle in dirty conditions, get your brakes checked and cleaned as necessary. • if y...

  • Page 321

    Warning! Continued operation with reduced power steering assist could pose a safety risk to yourself and others. Service should be obtained as soon as possible. Caution! Prolonged operation of the steering system at the end of the steering wheel travel will increase the steering fluid temperature an...

  • Page 322

    Parking brake to set the parking brake, pull the lever up as firmly as possible. When the parking brake is applied with the ignition on, the “brake warning light” in the instru- ment cluster will light. To release the parking brake, pull up slightly, press the center button, then lower the lever com...

  • Page 323

    Warning! • always apply the parking brake fully when leav- ing your vehicle or it may roll and cause damage or injury. Also, be certain to leave the transmission in the park position. Failure to do so may allow the vehicle to roll and cause damage or injury. • leaving unattended children in a vehicl...

  • Page 324

    Warning! Significant over or under-inflation of tires or mixing sizes of tires or wheels on the vehicle can lead to loss of braking effectiveness. The abs conducts a low-speed self-test at about 12 mph (20 km/h). If you have your foot lightly on the brake while this test is occurring, you may feel s...

  • Page 325

    Warning! (continued) • the capabilities of an abs equipped vehicle must never be exploited in a reckless or dangerous manner, which could jeopardize the user’s safety or the safety of others. Caution! The abs is subject to possible detrimental effects of electronic interference caused by improperly ...

  • Page 326

    Build up between the tire tread and the road. This hydroplaning action can cause loss of traction, braking ability, and control. • after going through deep water or a car wash, brakes may become wet, resulting in decreased performance and unpredictable braking action. Dry the brakes by gentle, inter...

  • Page 327

    Warning! The anti-lock brake system (abs) cannot prevent the natural laws of physics from acting on the ve- hicle, nor can it increase the traction afforded by prevailing road conditions. Abs cannot prevent acci- dents, including those resulting from excessive speed in turns, driving on very slipper...

  • Page 328

    Benefit of the system, you must apply continuous brak- ing pressure during the stopping sequence, (do not “pump” the brakes). Do not reduce brake pedal pressure unless braking is no longer desired. Once the brake pedal is released, the bas is deactivated. Warning! The brake assist system (bas) canno...

  • Page 329

    Warning! Many factors, such as vehicle loading, road condi- tions, and driving conditions, influence the chance that wheel lift or rollover may occur. Electronic roll mitigation (erm) cannot prevent all wheel lift or rollovers, especially those that involve leaving the roadway or striking objects or...

  • Page 330

    Warning! (continued) • failure to follow these warnings can result in an accident or serious personal injury. Hill start assist (hsa) the hsa system is designed to help the driver accelerate the vehicle from a complete stop while on an incline. If the driver releases the brake while stopped on an in...

  • Page 331

    Warning! There may be situations where the hill start assist (hsa) will not activate and slight rolling may occur, such as on minor hills (i.E., less than 7%), or with a loaded vehicle, or while pulling a trailer. Hsa is not a substitute for active driving involvement. It is always the driver’s resp...

  • Page 332

    Disabling and enabling hsa this feature can be turned on or turned off. To change the current setting, proceed as follows: for vehicles equipped with the electronic vehicle infor- mation center (evic), refer to “hill start assist,” under ⬙personal settings (customer programmable features),” under “e...

  • Page 333

    Hill descent control (hdc) — if equipped hdc is only intended for low speed off-road driving. Hdc maintains vehicle speed while descending hills in off-road driving conditions by applying the brakes when necessary. When enabled, hdc senses the terrain and activates when the vehicle is descending a h...

  • Page 334

    The “hill descent” button is located in the lower switch bank below the climate control. Enabling hdc 1. Shift the transfer case into 4wd low range. Refer to “four-wheel drive operation” in this section for transfer case operation information. 2. Press the “hill descent” button. The “hill descent co...

  • Page 335

    The esp uses sensors in the vehicle to determine the path that the driver intends to steer the vehicle and compares it to the actual path of the vehicle. When the actual path does not match the intended path, the esp applies the brake of the appropriate wheel to assist in counteracting the condition...

  • Page 336

    Depending upon model and mode of operation, the esp system has up to three operating modes: “esp on” “partial off,” and “full off.” esp on — two-wheel drive vehicles and four-wheel drive vehicles in 2wd and 4wd high range this is the normal operating mode for esp when operat- ing a two-wheel drive v...

  • Page 337

    Note: to improve the vehicle’s traction when driving with snow chains, or when starting off in deep snow, sand, or gravel, it may be desirable to switch to the “partial off” mode by momentarily depressing the “esp off” button. Once the situation requiring “partial off” mode is overcome, turn esp bac...

  • Page 338

    In this mode, esp and tcs are turned off (except for the “limited slip” feature described in the tcs section) until the vehicle reaches a speed of 40 mph (64 km/k). At speeds over 40 mph (64 km/k), the system automatically switches to “partial off” mode, described above. When the vehicle speed retur...

  • Page 339

    Running. If the “esp/bas malfunction indicator light” turns on continuously with the engine running, a mal- function has been detected in either the esp or the bas system, or both. If this light remains on after several ignition cycles, and the vehicle has been driven several miles/kilometers at spe...

  • Page 340

    Note: • p (passenger) - metric tire sizing is based on u.S. Design standards. P-metric tires have the letter “p” molded into the sidewall preceding the size designa- tion. Example: p215/65r15 95h. • european-metric tire sizing is based on european design standards. Tires designed to this standard ha...

  • Page 341

    Tire sizing chart example: size designation: p = passenger car tire size based on u.S. Design standards ⴖ....Blank....ⴖ = passenger car tire based on european design standards lt = light truck tire based on u.S. Design standards t = temporary spare tire 31 = overall diameter in inches (in) 215 = sec...

  • Page 342

    Example: service description: 95 = load index — a numerical code associated with the maximum load a tire can carry h = speed symbol — a symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions — the maximum speed corres...

  • Page 343

    Tire identification number (tin) the tin may be found on one or both sides of the tire, however, the date code may only be on one side. Tires with white sidewalls will have the full tin, including the date code, located on the white sidewall side of the tire. Look for the tin on the outboard side of...

  • Page 344

    Tire loading and tire pressure tire placard location note: the proper cold tire inflation pressure is listed on the driver’s side b-pillar. Tire and loading information placard this placard tells you important information about the: 1) number of people that can be carried in the vehicle 2) total wei...

  • Page 345

    Note: under a maximum loaded vehicle condition, gross axle weight ratings (gawrs) for the front and rear axles must not be exceeded. For further information on gawrs, vehicle loading, and trailer towing, refer to “vehicle loading” in this section. To determine the maximum loading conditions of your ...

  • Page 346

    5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in step 4. 6. If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. Consult th...

  • Page 347

    Starting and operating 345 5.

  • Page 348

    Warning! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. Tires — general information tire pressure proper tire inflation pressur...

  • Page 349

    Warning! (continued) • unequal tire pressures can cause steering prob- lems. You could lose control of your vehicle. • over-inflated or under-inflated tires can affect vehicle handling and can fail suddenly, resulting in loss of vehicle control. • unequal tire pressures from one side of the vehicle ...

  • Page 350

    The pressure should be checked and adjusted, as well as inspected for signs of tire wear or visible damage, at least once a month. Use a good quality pocket-type gauge to check tire pressure. Do not make a visual judgement when determining proper inflation. Radial tires may look properly inflated ev...

  • Page 351

    Tire pressure may increase from 2 to 6 psi (13 to 40 kpa) during operation. Do not reduce this normal pressure build-up, or your tire pressure will be too low. Tire pressures for high speed operation the manufacturer advocates driving at safe speeds within posted speed limits. Where speed limits or ...

  • Page 352

    Cuts and punctures in radial tires are repairable only in the tread area because of sidewall flexing. Consult your authorized dealer for radial tire repairs. Compact spare tire — if equipped the compact spare is for temporary emergency use with radial tires. It is engineered to be used on your style...

  • Page 353

    Caution! Because of the reduced ground clearance, do not take your vehicle through an automatic car wash with the compact spare installed. Damage to the vehicle may result. Tire spinning when stuck in mud, sand, snow, or ice conditions, do not spin your vehicle’s wheels above 35 mph (55 km/h). Warni...

  • Page 354

    These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth becomes 1/16 in (2 mm). When the indicators appear in two or more adjacent grooves, the tire should be replaced. Life of tire the service life of a tire is dependent upon various factors ...

  • Page 355

    Warning! • do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change sus- pension dimensions and performance characteris- tics, resulting in changes to steering, handling, and braking of your vehicle. This can caus...

  • Page 356

    Caution! To avoid damage to your vehicle, tires, or chains, observe the following precautions: • do not use tire chains on vehicles equipped with tires other than p225/75r16 or smaller tires. There may not be adequate clearance for the chains and you are risking structural or body damage to your veh...

  • Page 357

    These cautions apply to all chain traction devices, includ- ing link and cable (radial) chains. Tire rotation recommendations tires on the front and rear axles of vehicles operate at different loads and perform different steering, handling, and braking functions. For these reasons, they wear at uneq...

  • Page 358

    Refer to the “maintenance schedule” in section 8 of this manual for the proper maintenance intervals. Remember, more frequent rotation is permissible if desired. Also, correct for anything causing rapid or unusual wear prior to performing the tire rotation. Tire pressure monitor system (tpms) the ti...

  • Page 359

    Telltale light will turn off once the system receives the updated tire pressures. The vehicle may need to be driven for up to 20 minutes above 15 mph (25 km/h) in order for the tpms to receive this information. For example, your vehicle may have a recommended cold (parked for more than three hours) ...

  • Page 360

    Note: • the tpms is not intended to replace normal tire care and maintenance, or to provide warning of a tire failure or condition. • the tpms should not be used as a tire pressure gauge while adjusting your tire pressure. • driving on a significantly under-inflated tire causes the tire to overheat ...

  • Page 361

    The matching full-size spare wheel and tire assembly (if equipped) has a tire pressure monitoring sensor. The matching full-size spare can be used in place of any of the four road tires. The tpms will only monitor the pressure in the full-size spare when it is used in place of a road tire. Otherwise...

  • Page 362

    3. Lots of snow or ice around the wheels or wheel housings. 4. Using tire chains on the vehicle. 5. Using wheels/tires not equipped with tpms sensors. Vehicles with full-size spare 1. The matching full-size spare wheel and tire assembly has a tire pressure monitoring sensor that can be moni- tored b...

  • Page 363

    Telltale light will turn off, as long as no tire pressure is below the low-pressure warning limit in any of the four active road tires. The vehicle may need to be driven for up to 20 minutes above 15 mph (25 km/h) in order for the tpms to receive this information. Premium system — if equipped the ti...

  • Page 364

    Tire pressure monitoring low pressure warnings the tire pressure monitoring telltale light will illuminate in the instrument cluster and a chime will sound when tire pressure is low in one or more of the four active road tires. In addition, the electronic vehicle information center (evic) will displ...

  • Page 365

    If the ignition key is cycled, this sequence will repeat, providing the system fault still exists. If the system fault no longer exists, the tire pressure monitoring telltale light will no longer flash, and the ⬙check tpm sys- tem ⬙ message will no longer display, and a pressure value will display i...

  • Page 366

    On upon the next ignition key cycle. In addition, the evic will display a low pressure message and a graphic showing the low tire pressure value flashing. 3. After driving the vehicle for up to 20 minutes above 15 mph (25 km/h) the tpms telltale light will turn off, as long as no tire pressure is be...

  • Page 367

    5. Once you repair or replace the original road tire and reinstall it on the vehicle in place of the compact spare, the tpms will update automatically. In addition, the tpms telltale light will turn off and the graphic in the evic will display a new pressure value instead of dashes (- -), as long as...

  • Page 368

    As hard starting, stalling, and hesitations. If you experi- ence these symptoms, try another brand of gasoline before considering service for the vehicle. Over 40 auto manufacturers worldwide have issued and endorsed consistent gasoline specifications (the world- wide fuel charter, wwfc) which defin...

  • Page 369

    Problems that result from using methanol/gasoline or e85 ethanol blends are not the responsibility of the manufacturer. While mtbe is an oxygenate made from methanol, it does not have the negative effects of methanol. E-85 usage in non-flex fuel vehicles non-ffv vehicles are compatible with gasoline...

  • Page 370

    Of gasoline may not be indicated on the gasoline pump; therefore, you should ask your gasoline retailer whether the gasoline contains mmt. It is even more important to look for gasolines without mmt in canada, because mmt can be used at levels higher than those allowed in the united states. Mmt is p...

  • Page 371

    • the use of fuel additives, which are now being sold as octane enhancers, is not recommended. Most of these products contain high concentrations of methanol. Fuel system damage or vehicle performance problems resulting from the use of such fuels or additives is not the responsibility of the manufac...

  • Page 372

    Adding fuel fuel filler cap (gas cap) the gas cap is located behind the fuel filler door on the left side of the vehicle. If the gas cap is lost or damaged, be sure the replacement cap is designed for use with this vehicle. Caution! • damage to the fuel system or emission control system could result...

  • Page 373

    Warning! (continued) • never add fuel to the vehicle when the engine is running. • a fire may result if gasoline is pumped into a portable container that is inside of a vehicle. You could be burned. Always place gas containers on the ground while filling. Note: • tighten the gas cap until you hear a...

  • Page 374

    This label contains the month and year of manufacture, gross vehicle weight rating (gvwr), gross axle weight rating (gawr) front and rear, and vehicle identification number (vin). A month-day-hour (mdh) number is included on this label and indicates the month, day, and hour of manufacture. The bar c...

  • Page 375

    Inflation pressure this is the cold tire inflation pressure for your vehicle for all loading conditions up to full gawr. Curb weight the curb weight of a vehicle is defined as the total weight of the vehicle with all fluids, including vehicle fuel, at full capacity conditions, and with no occupants ...

  • Page 376

    Caution! Do not load your vehicle any heavier than the gvwr or the maximum front and rear gawr. If you do, parts on your vehicle can break, or it can change the way your vehicle handles. This could cause you to lose control. Also, overloading can shorten the life of your vehicle. Trailer towing in t...

  • Page 377

    Warning! If the gross trailer weight (gtw) is 3,500 lbs (1 587 kg) or more, it is mandatory to use a weight-distributing hitch to ensure stable handling of your vehicle. If you use a standard weight- carrying hitch, you could lose control of your vehicle and cause an accident. Gross combination weig...

  • Page 378

    Trailer sway control — electronic refer to “tsc (trailer sway control)” under “electronic brake control system” in this section for information on this system. Trailer sway control — mechanical the trailer sway control is a telescoping link that can be installed between the hitch receiver and the tr...

  • Page 379

    Warning! • an improperly adjusted weight distributing hitch system may reduce handling, stability, brak- ing performance, and could result in an accident. • weight distributing systems may not be compat- ible with surge brake couplers. Consult with your hitch and trailer manufacturer or a reputable ...

  • Page 380

    With weight distributing hitch (correct) improper adjustment of weight-distributing hitch (incorrect) 378 starting and operating.

  • Page 381

    Trailer hitch classification your vehicle is capable of towing trailers up to 2,000 lbs (907 kg) without added equipment or alterations to the standard equipment. Your vehicle may be factory equipped for safe towing of trailers weighing over 2,000 lbs (907 kg) with the optional trailer tow prep pack...

  • Page 382

    Trailer towing weights (maximum trailer weight ratings) the following chart provides the maximum trailer weight ratings towable for your given drivetrain. Engine/ transmission model frontal area max. Gtw (gross trailer wt.) tongue wt. (see note) 3.7l/automatic 4x2 32 sq ft (2.97 sq m) 2,000 lbs (907...

  • Page 383

    When towing trailers with gross trailer weight (gtw) between 3,500 lbs (1 588 kg) and 5,000 lbs (2 268 kg) the following chart provides maximum trailer weight ratings towable for the following engine/transmission combinations, only if using a weight distributing hitch. Engine/ transmission model fro...

  • Page 384

    Trailer and tongue weight always load a trailer with 60% to 65% of the weight in the front of the trailer. This places 10% to 15% of the gross trailer weight (gtw) on the tow hitch of your vehicle. Loads balanced over the wheels or heavier in the rear can cause the trailer to sway severely side to s...

  • Page 385

    Note: remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options, or authorized dealer-installed options, must be considered as part of the total load on your vehicle. Refer to the “tire and loading information” placard for the ma...

  • Page 386

    • safety chains must always be used between your vehicle and trailer. Always connect the chains to the frame or hook retainers of the vehicle hitch. Cross the chains under the trailer tongue and allow enough slack for turning corners. • vehicles with trailers should not be parked on a grade. When pa...

  • Page 387

    − check for signs of tire wear or visible tire damage before towing a trailer. Refer to “tires–general infor- mation” in this section for information on tread wear indicators and for the proper inspection procedure. − when replacing tires, refer to “tires–general informa- tion” in this section for i...

  • Page 388

    Warning! • do not connect trailer brakes to your vehicle’s hydraulic brake lines. It can overload your brake system and cause it to fail. You might not have brakes when you need them and could have an accident. • towing any trailer will increase your stopping distance. When towing you should allow f...

  • Page 389

    Four-pin connector 1 — female pins 4 — park 2 — male pin 5 — left stop/turn 3 — ground 6 — right stop/turn seven-pin connector 1 — battery 5 — ground 2 — backup lamps 6 — left stop/turn 3 — right stop/turn 7 — running lamps 4 — electric brakes starting and operating 387 5.

  • Page 390

    Towing tips before setting out on a trip, practice turning, stopping, and backing the trailer in an area located away from heavy traffic. Automatic transmission the “d” range can be selected when towing. However, if frequent shifting occurs while in this range, you will want to activate the tow/haul...

  • Page 391

    Cooling system to reduce potential for engine and transmission over- heating, take the following actions: − city driving when stopped for short periods of time, put transmission in neutral and increase engine idle speed. − highway driving reduce speed. − air conditioning turn off temporarily. Recrea...

  • Page 392

    Caution! (continued) • before recreational towing, perform the procedure outlined under “shifting into neutral” to be certain that the transfer case is fully in neutral. Otherwise, internal damage will result. • do not use a bumper mounted clamp-on tow bar on your vehicle. The bumper face bar will b...

  • Page 393

    10. Repeat steps 8 and 9 with the transmission in drive. 11. Turn off the engine. 12. Turn the ignition switch to the unlocked off posi- tion. 13. Shift the transmission into park. 14. Attach the vehicle to a tow vehicle with a tow bar. 15. Disconnect the battery negative cable. Note: steps 1 throug...

  • Page 394

    2. Reconnect the battery negative cable. 3. Place the ignition switch in the lock position (if it has been moved or the engine has been started). 4. Turn the ignition switch to the on position, but do not start the engine. 5. Press the brake pedal. 6. Shift the transmission into neutral. 7. Use the ...

  • Page 395: Contents

    What to do in emergencies contents 䡵 hazard warning flasher . . . . . . . . . . . . . . . . 394 䡵 if your engine overheats . . . . . . . . . . . . . . . . 394 䡵 jacking and tire changing . . . . . . . . . . . . . . . 395 ▫ jack location . . . . . . . . . . . . . . . . . . . . . . . 396 ▫ spare tire ...

  • Page 396

    Hazard warning flasher the hazard warning flasher switch is located in the switch bank below the climate controls. Press the switch to turn on the hazard warning flasher. When the switch is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency. Press ...

  • Page 397

    Note: there are steps that you can take to slow down an impending overheat condition: • if your air conditioner (a/c) is on, turn it off. The a/c system adds heat to the engine cooling system and turning the a/c can help remove this heat. • you can also turn the temperature control to maxi- mum heat...

  • Page 398

    Jack location the scissor-type jack and tire changing tools are located in the cargo compartment behind a trim cover on the left rear trim panel. The latch is located at the bottom of the trim cover. Spare tire stowage the spare tire is stowed underneath the rear of the vehicle and is held in place ...

  • Page 399

    Caution! The winch mechanism is designed for use with the jack extension tube only. Use of an air wrench or other power tools is not recommended and they can damage the winch. When the spare is clear, tilt the retainer at the end of the cable, and pull it through the center of the wheel. Preparation...

  • Page 400

    5. Turn on the hazard warning flasher. 6. Block both the front and rear of the wheel diagonally opposite of the jack- ing position. For example, if changing the right front tire, block the left rear wheel. Note: passengers should not remain in the vehicle when the vehicle is being jacked. Jacking in...

  • Page 401

    Warning! (continued) • do not let anyone sit in the vehicle when it is on a jack. • do not get under the vehicle when it is on a jack. • only use the jack in the positions indicated and for lifting this vehicle during a tire change. • if working on or near a roadway, be extremely careful of motor tr...

  • Page 402

    4. Locate the jack as shown. For the front tires, place it (rearward) of the notch on the body weld seam behind wheel to be changed. For the rear tires, place it under the axle by the wheel to be changed. Position the jack handle on the jack. Do not raise the vehicle until you are sure the jack is f...

  • Page 403

    Warning! Raising the vehicle higher than necessary can make the vehicle less stable and cause an accident. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. 6. Remove the lug nuts and wheel. 7. Position the spare wheel/tire on the vehicle and inst...

  • Page 404

    Jump-starting warning! • take care to avoid the radiator cooling fan when- ever the hood is raised. It can start anytime the ignition switch is on. You can be hurt by the fan. • do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic transmission cannot be s...

  • Page 405

    2. When boosting from a battery in another vehicle, park that vehicle within booster cable reach, but without allowing the vehicles to touch. Warning! Do not permit vehicles to touch each other as this could establish a ground connection and personal injury could result. 3. Set the parking brake, pl...

  • Page 406

    7. If the vehicle is equipped with sentry key 威 immobi- lizer, turn the ignition switch to the on position for three seconds before moving the ignition switch to the start position. 8. Start the engine in the vehicle that has the booster battery, let the engine idle a few minutes, and then start the...

  • Page 407

    Towing methods note: when towing a 4x4 model, the transfer case must be in neutral and the transmission must be in park. Model flat towing (all four wheels on the ground) flatbed towing (recommended method) front wheels raised, rear wheels on the ground rear wheels raised, front wheels on the ground...

  • Page 409: Maintaining Your Vehicle

    Maintaining your vehicle contents 䡵 engine compartment — 3.7l . . . . . . . . . . . . . 409 䡵 onboard diagnostic system — obd ii . . . . . . 410 ▫ loose fuel filler cap message . . . . . . . . . . . 410 䡵 emissions inspection and maintenance programs . . . . . . . . . . . . . . . . . . . . . . . . ....

  • Page 410

    ▫ cooling system . . . . . . . . . . . . . . . . . . . . . 423 ▫ brake system . . . . . . . . . . . . . . . . . . . . . . . 429 ▫ automatic transmission . . . . . . . . . . . . . . . 430 ▫ transfer case . . . . . . . . . . . . . . . . . . . . . . . 431 ▫ front/rear axle fluid . . . . . . . . . . . ....

  • Page 411

    Engine compartment — 3.7l 1 — air cleaner filter 6 — washer fluid reservoir 2 — engine oil dipstick 7 — engine coolant reservoir 3 — brake fluid reservoir 8 — engine oil fill 4 — integrated power module 9 — coolant pressure cap 5 — battery maintaining your vehicle 409 7.

  • Page 412

    Onboard diagnostic system — obd ii your vehicle is equipped with a sophisticated onboard diagnostic system called obd ii. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide ex...

  • Page 413

    Appear the next time the vehicle is started. This might indicate a damaged cap. If the problem is detected twice in a row, the system will turn on the mil. Resolving the problem will turn the mil light off. Emissions inspection and maintenance programs in some localities, it may be a legal requireme...

  • Page 414

    5. Approximately 15 seconds later, one of two things will happen: a. The mil will flash for about 10 seconds and then return to being fully illuminated until you turn off the ignition or start the engine. This means that your vehicle’s obd ii system is not ready and you should not proceed to the i/m...

  • Page 415

    Your vehicle. Refer to these manuals before attempting any procedure yourself. Note: intentional tampering with emissions control systems can result in civil penalties being assessed against you. Warning! You can be badly injured working on or around a motor vehicle. Only do service work for which y...

  • Page 416

    Dipstick. Adding 1 quart (0.9 l) of oil when the reading is at the bottom of the safe zone will result in a reading at the top of the safe zone on these engines. Caution! Overfilling or underfilling the crankcase will cause aeration or loss of oil pressure. This could damage your engine. Change engi...

  • Page 417

    Engine oil viscosity sae 5w-20 engine oil is recommended for all operating temperatures. This engine oil improves low temperature starting and vehicle fuel economy. The engine oil filler cap also shows the recommended engine oil viscosity for your engine. For information on engine oil filler cap loc...

  • Page 418

    Engine oil filter selection all of this manufacturer’s engines have a full-flow type disposable oil filter. Use a filter of this type for replace- ment. The quality of replacement filters varies consider- ably. Only high-quality filters should be used to assure most efficient service. Mopar 威 engine...

  • Page 419

    Maintenance-free battery the top of the maintenance-free battery is permanently sealed. You will never have to add water, nor is periodic maintenance required. Warning! • battery fluid is a corrosive acid solution and can burn or even blind you. Do not allow battery fluid to contact your eyes, skin,...

  • Page 420

    Caution! (continued) • if a “fast charger” is used while the battery is in the vehicle, disconnect both vehicle battery cables before connecting the charger to the battery. Do not use a “fast charger” to provide starting voltage as battery damage can result. Air conditioner maintenance for best poss...

  • Page 421

    Refrigerant recovery and recycling r-134a air conditioning refrigerant is a hydrofluoro- carbon (hfc) that is endorsed by the environmental protection agency and is an ozone-saving product. How- ever, the manufacturer recommends that air conditioning service be performed by an authorized dealer or o...

  • Page 422

    Windshield wiper blades clean the rubber edges of the wiper blades and the windshield periodically with a sponge or soft cloth and a mild non-abrasive cleaner or use the washer solvent. This will remove accumulations of salt or road film. Operation of the wipers on dry glass for long periods may cau...

  • Page 423

    Exhaust system the best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system. If you notice a change in the sound of the exhaust system or if the exhaust fumes can be detected inside the vehicle, or when the underside or rear of the vehicle is...

  • Page 424

    Caution! Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition. In the event of engine malfunction, particularly involv- ing engine misfire or other apparent loss of perfor- mance, have your vehicle serviced promptly. Contin- ued operation of your veh...

  • Page 425

    To minimize the possibility of catalytic converter dam- age: • do not shut off the engine or interrupt the ignition when the transmission is in gear and the vehicle is in motion. • do not try to start the engine by pushing or towing the vehicle. • do not idle the engine with any ignition coil connec...

  • Page 426

    Spraying water from a garden hose vertically down the face of the a/c condenser (if equipped) or the back of the radiator core. Check the engine cooling system hoses for brittle rubber, cracking, tears, cuts, and tightness of the connection at the coolant recovery bottle and radiator. Inspect the en...

  • Page 427

    Caution! • mixing of engine coolant (antifreeze) other than specified hoat engine coolant (antifreeze), may result in engine damage and may decrease corro- sion protection. If a non-hoat engine coolant (antifreeze) is introduced into the cooling system in an emergency, it should be replaced with the...

  • Page 428

    When adding engine coolant (antifreeze): • the manufacturer recommends using mopar威 antifreeze/coolant 5 year/100,000 mile formula hoat (hybrid organic additive technology). • mix a minimum solution of 50% hoat engine coolant (antifreeze) and distilled water. Use higher concentra- tions (not to exce...

  • Page 429

    Warning! • the warning words “do not open hot” on the cooling system pressure cap are a safety pre- caution. Never add engine coolant (antifreeze) when the engine is overheated. Do not loosen or remove the cap to cool an overheated engine. Heat causes pressure to build up in the cooling system. To p...

  • Page 430

    The engine operating temperature is satisfactory, the coolant bottle need only be checked once a month. When additional engine coolant (antifreeze) is needed to maintain the proper level, it should be added to the coolant bottle. Do not overfill. Points to remember note: when the vehicle is stopped ...

  • Page 431

    • do not change the thermostat for summer or winter operation. If replacement is ever necessary, install only the correct type thermostat. Other designs may result in unsatisfactory cooling performance, poor gas mileage, and increased emissions. Brake system in order to assure brake system performan...

  • Page 432

    Warning! • overfilling the brake fluid reservoir can result in spilling brake fluid on hot engine parts and the brake fluid catching fire. • use of a brake fluid that has a lower initial boiling point than the recommended product or a brake fluid that is unidentified as to fmvss specification may re...

  • Page 433

    Fluid and filter changes refer to the “maintenance schedule” in section 8 for the proper maintenance intervals. In addition, change the fluid and filter if the transmission is disassembled for any reason. Special additives the manufacturer strongly recommends against the ad- dition of any additives ...

  • Page 434

    Draining fluid first remove fill plug (2), then drain plug (3). Recom- mended tightening torque for drain and fill plugs is 15–25 ft lbs (20–34 n·m). Caution! Do not over-tighten the plugs. You could damage them and cause a leak. Lubricant selection use only manufacturer’s recommended fluid. Refer t...

  • Page 435

    Sky slider 姞top care immediate removal of any contaminant is recommended. Regular washing of the top will enhance its life and appearance, and make successive cleaning easier. Do not subject the top to excessive heat. Frequently vacuum the top and tracks. Periodically wipe dust and dirt from the top...

  • Page 436

    • allow the top to dry before opening. Vacuuming the top with a wet/dry shop vacuum will decrease the tops drying time, ensure removal of all dirt, and delete streaks in the material. • multiple cleanings may be necessary to remove stub- born stains. If stains persist, contact your local autho- rize...

  • Page 437

    Weather strip care lubricate the weather strips periodically with mopar 威 weather strip lubricant, to keep them soft and pliable. Appearance care and protection from corrosion protection of body and paint from corrosion vehicle body care requirements vary according to geo- graphic locations and usag...

  • Page 438

    • if insects, tar, or other similar deposits have accumu- lated on your vehicle, use mopar 威 super kleen bug and tar remover to remove. • use mopar威 cleaner wax to remove road film, stains, and to protect your paint finish. Take care never to scratch the paint. • avoid using abrasive compounds and p...

  • Page 439

    • if you carry special cargo such as chemicals, fertilizers, de-icer salt, etc., assure that such materials are well packaged and sealed. • if a lot of driving is done on gravel roads, consider mud or stone shields behind each wheel. • use mopar威 touch up paint or equivalent on scratches or chips as...

  • Page 440

    • for grease stains, apply mopar威 multi-purpose cleaner to a clean, damp cloth and remove the stain. Use a fresh, damp towel to remove soap residue. • do not use any solvents or protectants on stain repel products. Interior care instrument panel cover the instrument panel cover has a low glare surfa...

  • Page 441

    Warning! Do not use volatile solvents for cleaning purposes. Many are potentially flammable, and if used in closed areas they may cause respiratory harm. Cleaning headlights your vehicle has plastic headlights that are lighter and less susceptible to stone breakage than glass headlights. Plastic is ...

  • Page 442

    1. Clean with a wet soft rag. A mild soap solution may be used, but do not use high alcohol content or abrasive cleaners. If soap is used, wipe clean with a clean damp rag. 2. Dry with a soft cloth. Seat belt maintenance do not bleach, dye, or clean the seat belts with chemical solvents or abrasive ...

  • Page 443

    Cav- ity car- tridge fuse mini- fuse description j1 — — — j2 30 amp pink — transfer case module - if equipped j3 40 amp green — rear door modules j4 25 amp white — driver door node j5 25 amp white — passenger door node j6 40 amp green — anti-lock brake system (abs) pump/esp - if equipped j7 30 amp p...

  • Page 444

    Cav- ity car- tridge fuse mini- fuse description j18 20 amp blue — powertrain control mod- ule (pcm) transmission relay j19 60 amp yellow — radiator fan j20 30 amp pink — front wiper j21 20 amp blue — front washer/rear washer - if equipped j22 25 amp white — sunroof module - if equipped m1 — 15 amp ...

  • Page 445

    Cav- ity car- tridge fuse mini- fuse description m10 — 15 amp blue hands-free module (hfm) – if equipped/ universal garage door opener (ugdo) – if equipped/vanity light m11 — 10 amp red automatic temperature control (atc) - if equipped m12 — 30 amp green radio/amplifier - if equipped m13 — 20 amp ye...

  • Page 446

    Cav- ity car- tridge fuse mini- fuse description m18 — 15 amp blue exterior lighting — right front park and side marker, right tail and running lights m19 — 25 amp natural auto shut down (asd) #1 and #2 m20 — 15 amp blue interior lighting/steering wheel switches - if equipped/switch bank/ electronic...

  • Page 447

    Cav- ity car- tridge fuse mini- fuse description m30 — 15 amp blue rear wiper module - if equipped/diagnostic link m31 — 20 amp yellow back-up lights m32 — 10 amp red occupant restraint con- troller (orc) m33 — 10 amp red powertrain control mod- ule (pcm) m34 — 10 amp red park assist module - if equ...

  • Page 448

    Caution! • when installing the integrated power module cover, it is important to ensure the cover is prop- erly positioned and fully latched. Failure to do so may allow water to get into the integrated power module, and possibly result in an electrical system failure. • when replacing a blown fuse, ...

  • Page 449

    Bulb replacement headlight 1. Open the hood. 2. Reach behind the headlight housing to access the headlight bulb lock ring. 3. Firmly grasp the lock ring and rotate it counterclock- wise to unlock it. 4. Remove the bulb and connector assembly from the headlight housing. 5. Disconnect the bulb from th...

  • Page 450

    Front turn signal and front side marker lights 1. Turn the steering wheel all the way to the right to access the left front turn signal or side marker. Turn the steering wheel all the way to the left to access the right front turn signal or side marker. 2. Remove three push-pins from the wheel-well ...

  • Page 451

    6. Close the hood. Rear tail/stop, turn signal, and back-up lights 1. Open the liftgate. 2. Remove the screws that fasten the taillight housing to the vehicle. 3. Pull the taillight housing straight back to separate it from the vehicle. 4. Disconnect the electrical connector. 5. Remove the two screw...

  • Page 452

    Fluid capacities u.S. Metric fuel (approximate) 19.5 gallons 73.8 liters engine oil with filter 3.7 liter engine (sae 5w-20, api certified) 5 quarts 4.7 liters cooling system * 3.7 liter engine (mopar 威 antifreeze/engine coolant 5 year/100,000 mile formula) 14 quarts 13.3 liters * includes heater an...

  • Page 453

    Fluids, lubricants, and genuine parts engine component fluid, lubricant, or genuine part engine coolant mopar 威 antifreeze/coolant 5 year/100,000 mile formula hoat (hybrid organic additive technology) engine oil (3.7l engine) use api certified sae 5w-20 engine oil, meeting the requirements of chrysl...

  • Page 454

    Chassis component fluid, lubricant, or genuine part automatic transmission mopar 威 atf+4 automatic transmission fluid transfer case mopar 威 atf+4 automatic transmission fluid front axle sae 80w-90 multi-purpose type, gl-5 gear lubricant or equivalent rear axle sae 75w-140 synthetic gear lubricant or...

  • Page 455: Maintenance Schedules

    Maintenance schedules contents 䡵 emissions control system maintenance . . . . . . 454 䡵 maintenance schedule . . . . . . . . . . . . . . . . . . 454 ▫ required maintenance intervals . . . . . . . . . . 456 8 m a i n t e n a n c e s c h e d u l e s.

  • Page 456

    Emissions control system maintenance the scheduled maintenance services listed in bold type must be done at the times or mileages specified to ensure the continued proper functioning of the emissions control system. These and all other maintenance services in- cluded in this manual, should be done t...

  • Page 457

    Note: • the oil change indicator message will not monitor the time since the last oil change. Change your vehicles oil if it has been six months since your last oil change even if the oil change indicator message is not illumi- nated. • change your engine oil more often if you drive your vehicle off...

  • Page 458

    • check the fluid levels of coolant reservoir, brake master cylinder, and transmission and add as needed. • check all lights and other electrical items for correct operation. At each oil change • change the engine oil filter. • inspect the brake hoses and lines. Caution! Failure to perform the requi...

  • Page 459

    6,000 miles (10,000 km) or 6 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. Odometer reading date repair order # dealer code signature authorized chrysler dealer 12,000 miles (20,000 km) or 12 months maintenance service schedule ❏ change the engine...

  • Page 460

    18,000 miles (30,000 km) or 18 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. ❏ inspect the front and rear axle fluid; change if using your vehicle for police, taxi, fleet, off-road or frequent trailer towing. Odometer reading date repair order # d...

  • Page 461

    36,000 miles (60,000 km) or 36 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. ❏ if using your vehicle for any of the following: dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. ❏ inspect the brake linings; ...

  • Page 462

    54,000 miles (90,000 km) or 54 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. ❏ inspect the front and rear axle fluid; change if using your vehicle for police, taxi, fleet, off-road or frequent trailer towing. Odometer reading date repair order # d...

  • Page 463

    66,000 miles (110,000 km) or 66 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. Odometer reading date repair order # dealer code signature authorized chrysler dealer 72,000 miles (120,000 km) or 72 months maintenance service schedule ❏ change the en...

  • Page 464

    78,000 miles (130,000 km) or 78 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. Odometer reading date repair order # dealer code signature authorized chrysler dealer 84,000 miles (140,000 km) or 84 months maintenance service schedule ❏ change the en...

  • Page 465

    90,000 miles (150,000 km) or 90 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. ❏ replace the engine air cleaner filter. ❏ inspect and replace pcv valve if necessary. † ❏ replace the spark plugs (3.7l engine). ❏ adjust parking brake on vehicles equi...

  • Page 466

    102,000 miles (170,000 km) or 102 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. ❏ flush and replace the engine coolant if not done at 60 months. Odometer reading date repair order # dealer code signature authorized chrysler dealer 108,000 miles (1...

  • Page 467

    120,000 miles (200,000 km) or 120 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. ❏ replace the engine air cleaner filter. ❏ replace the ignition cables (3.7l engine). ❏ replace the spark plugs (3.7l engine). ❏ inspect the brake linings; replace if ...

  • Page 468

    132,000 miles (220,000 km) or 132 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. ❏ if using your vehicle for any of the following: dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. ❏ inspect the brake lining...

  • Page 469

    144,000 miles (240,000 km) or 144 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. ❏ if using your vehicle for any of the following: dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. ❏ inspect the brake lining...

  • Page 470

    † this maintenance is recommended by the manufacturer to the owner, but is not required to maintain emissions warranty. Warning! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the right equipment. If you have any doubt ab...

  • Page 471: Contents

    If you need consumer assistance contents 䡵 suggestions for obtaining service for your vehicle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 471 ▫ prepare for the appointment . . . . . . . . . . . 471 ▫ prepare a list . . . . . . . . . . . . . . . . . . . . . . 471 ▫ be reasonable with r...

  • Page 472

    䡵 department of transportation uniform tire quality grades . . . . . . . . . . . . . . . . . . . . . . . . 476 ▫ treadwear . . . . . . . . . . . . . . . . . . . . . . . . . 477 ▫ traction grades . . . . . . . . . . . . . . . . . . . . . 477 ▫ temperature grades . . . . . . . . . . . . . . . . . . 47...

  • Page 473

    Suggestions for obtaining service for your vehicle prepare for the appointment if you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty. Discuss additional charges with the service manager. ...

  • Page 474

    This is why you should always talk to an authorized dealer’s service manager first. Most matters can be re- solved with this process. • if for some reason you are still not satisfied, talk to the general manager or owner of the authorized dealer- ship. They want to know if you need assistance. • if ...

  • Page 475

    Customer assistance for the hearing or speech impaired (tdd/tty) to assist customers who have hearing difficulties, the manufacturer has installed special tdd (telecommuni- cation devices for the deaf) equipment at its customer center. Any hearing or speech impaired customer, who has access to a tdd...

  • Page 476

    The ownership experience. You’ll be pleased with their sincere efforts to resolve any warranty issues or related concerns. Warning! Engine exhaust, some of its constituents, and certain vehicle components contain, or emit, chemicals known to the state of california to cause cancer and birth defects,...

  • Page 477

    To contact nhtsa, you may either call the auto safety hotline toll free at 1–888–327–4236 (tty: 1–800–424– 9153), or go to http://www.Safercar.Gov; or write to: administrator, nhtsa, 400 seventh street, sw., wash- ington, d.C. 20590. You can also obtain other information about motor vehicle safety f...

  • Page 478

    • diagnostic procedure manuals diagnostic procedure manuals are filled with dia- grams, charts and detailed illustrations. These practi- cal manuals make it easy for students and technicians to find and fix problems on computer-controlled ve- hicle systems and features. They show exactly how to find...

  • Page 479

    Treadwear the treadwear grade is a comparative rating, based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half times as well on the government course as a tire graded 100. The relativ...

  • Page 480

    Temperature grades the temperature grades are a (the highest), b, and c, representing the tire’s resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the mater...

  • Page 481: Index

    Index 10

  • Page 482

    About your brakes . . . . . . . . . . . . . . . . . . . . . . . 320 abs (anti-lock brake system) . . . . . . . . . . . . 321,324 adding engine coolant (antifreeze) . . . . . . . . . . 425 adding fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . 370 additives, fuel . . . . . . . . . . . . . ...

  • Page 483

    Automatic headlights . . . . . . . . . . . . . . . . . . . . 143 automatic oil change indicator . . . . . . . . . . 212,218 automatic temperature control (atc) . . . . . . . . . 277 automatic transaxle . . . . . . . . . . . . . . . . . . . . . . 294 special additives . . . . . . . . . . . . . . . . ...

  • Page 484

    Brakes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 429 brake/transmission interlock . . . . . . . . . . . . . . . 295 break-in recommendations, new vehicle . . . . . . . . 80 brightness, interior lights . . . . . . . . . . . . . . . . . . 148 bulb replacement . . . . . . . . . . . ...

  • Page 485

    Climate control . . . . . . . . . . . . . . . . . . . . . . . . . 274 clock . . . . . . . . . . . . . . . . . . . . . . . . 229,243,246,255 coin holder . . . . . . . . . . . . . . . . . . . . . . . . . . . 185 cold weather operation . . . . . . . . . . . . . . . . . . . 291 command-trac operation . ...

  • Page 486

    Dimmer switch, headlight . . . . . . . . . . . . . . . . . 147 dipsticks oil (engine) . . . . . . . . . . . . . . . . . . . . . . . . . . 413 power steering . . . . . . . . . . . . . . . . . . . . . . . . 319 disposal antifreeze (engine coolant) . . . . . . . . . . . . . . . 427 engine oil . . . . ....

  • Page 487

    Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 409 air cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . 416 block heater . . . . . . . . . . . . . . . . . . . . . . . . . 293 break-in recommendations . . . . . . . . . . . . . . . . 80 checking oil level . . . . . . ....

  • Page 488

    Engine oil . . . . . . . . . . . . . . . . . . . . . . . . 415,451 engine oil disposal . . . . . . . . . . . . . . . . . . . . 415 finish care . . . . . . . . . . . . . . . . . . . . . . . . . . . . 435 flashers hazard warning . . . . . . . . . . . . . . . . . . . . . . . 394 turn signal . . . . . ....

  • Page 489

    Materials added . . . . . . . . . . . . . . . . . . . . . . . 368 methanol . . . . . . . . . . . . . . . . . . . . . . . . . . . . 366 octane rating . . . . . . . . . . . . . . . . . . . . . . 365,451 requirements . . . . . . . . . . . . . . . . . . . . . . . . . 365 specifications . . . . . . . . ....

  • Page 490

    Automatic . . . . . . . . . . . . . . . . . . . . . . . . . . . 143 bulb replacement . . . . . . . . . . . . . . . . . . . . . . 447 cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . 439 delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144 high beam/low beam select sw...

  • Page 491

    Instrument panel cover . . . . . . . . . . . . . . . . . . . 438 instrument panel lens cleaning . . . . . . . . . . . . . 439 integrated power module (fuses) . . . . . . . . . . . . 440 interior appearance care . . . . . . . . . . . . . . . . . . 438 interior lighting . . . . . . . . . . . . . . . ....

  • Page 492

    Automatic headlights . . . . . . . . . . . . . . . . . . . 143 back-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . 449 battery saver . . . . . . . . . . . . . . . . . . . . . . . . . 148 brake assist warning . . . . . . . . . . . . . . . . 208,336 brake warning . . . . . . . . . . . . . ...

  • Page 493

    Rear servicing . . . . . . . . . . . . . . . . . . . . . . . . 449 rear tail . . . . . . . . . . . . . . . . . . . . . . . . . . . . 449 seat belt reminder . . . . . . . . . . . . . . . . . . . . . 213 service . . . . . . . . . . . . . . . . . . . . . . . . . . . 446,447 service engine soon (malfunc...

  • Page 494

    Manual transmission lubricant selection . . . . . . . . . . . . . . . . . . . . . 452 map/reading lights . . . . . . . . . . . . . . . . . . . . . 147 marker lights, side . . . . . . . . . . . . . . . . . . . . . . 448 master cylinder (brakes) . . . . . . . . . . . . . . . . . . 429 memory feature (...

  • Page 495

    Dipstick . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 413 disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . 415 filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . 415,451 filter disposal . . . . . . . . . . . . . . . . . . . . . . . . 415 identification logo ....

  • Page 496

    Steering . . . . . . . . . . . . . . . . . . . . . . . . . . 318,319 sunroof . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171 sunroof (sky slider) . . . . . . . . . . . . . . . . . 174,433 windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 power steering fluid . . . . ...

  • Page 497

    Replacement keys . . . . . . . . . . . . . . . . . . . . . . . . 16 replacement parts . . . . . . . . . . . . . . . . . . . . . . . 412 replacement tires . . . . . . . . . . . . . . . . . . . . . . . 352 reporting safety defects . . . . . . . . . . . . . . . . . . . 474 resetting oil change indicato...

  • Page 498

    Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127 adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . 127 easy entry . . . . . . . . . . . . . . . . . . . . . . . . . . . 139 head restraints . . . . . . . . . . . . . . . . . . . . . . . 131 heated . . . . . . . ....

  • Page 499

    Spark plugs . . . . . . . . . . . . . . . . . . . . . . . . . . . . 451 specifications fuel (gasoline) . . . . . . . . . . . . . . . . . . . . . . . . 451 oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 414,451 speed control (cruise control) . . . . . . . . . . . . . . 155 speedomete...

  • Page 500

    Theft alarm (security alarm) . . . . . . . . . . . . . . . . 18 theft system (security alarm) . . . . . . . . . . . . . . . 18 tie down hooks, cargo . . . . . . . . . . . . . . . . . . . 188 tilt steering column . . . . . . . . . . . . . . . . . . . . . 154 time delay, headlight . . . . . . . . . . ...

  • Page 501

    Behind a motor home . . . . . . . . . . . . . . . . . . 389 disabled vehicle . . . . . . . . . . . . . . . . . . . . . . . 404 guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 380 recreational . . . . . . . . . . . . . . . . . . . . . . . . . . 389 weight . . . . . . . . . . . . . ....

  • Page 502

    Turn signals . . . . . . . . . . . . . . . . 142,146,205,448,449 uconnect 威 (hands-free phone) . . . . . . . . . . . . . . . 94 uniform tire quality grades . . . . . . . . . . . . . . . . 476 universal transmitter . . . . . . . . . . . . . . . . . . . . . 165 unleaded gasoline . . . . . . . . . . . ...

  • Page 503

    Windshield wiper blades . . . . . . . . . . . . . . . . . . 420 windshield wipers . . . . . . . . . . . . . . . . . . . . . . . 149 wiper blade replacement . . . . . . . . . . . . . . . . . . 420 wiper, delay . . . . . . . . . . . . . . . . . . . . . . . . . . . 150 wiper, rear . . . . . . . . . . ....

  • Page 504

    Introduction introduction rollover warning how to use this manual warnings and cautions vehicle identification number vehicle modifications/alterations things to know before starting your vehicle a word about your keys ignition key removalkey-in-ignition remindersentry key replacement keyscustomer k...

  • Page 505

    Installation of radio transmitting equipment special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained person- nel. The following must be obs...

  • Page 506

    Liberty 2009 owner’s manual 2009 liber ty chrysler llc 81-326-0941 second edition printed in u.S.A..