1. DL manuals
  2. Jeep
  3. Automobile
  4. 2010 Grand Cherokee
  5. Owner's Manual

Jeep 2010 Grand Cherokee Owner's Manual

Other manuals for 2010 Grand Cherokee: Owner's Manual, User Manual

Summary of 2010 Grand Cherokee

  • Page 1

    Table of contents section page 1 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 things to know before starting your vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 3 understanding the featu...

  • Page 3: Introduction

    Introduction contents 䡵 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 䡵 rollover warning . . . . . . . . . . . . . . . . . . . . . . . 5 䡵 how to use this manual . . . . . . . . . . . . . . . . . . 6 䡵 warnings and cautions . . . . . . . . . . . . . . . . . . . 8 䡵 vehicle ide...

  • Page 4

    Introduction congratulations on selecting your new chrysler group llc vehicle. Be assured that it represents precision workmanship, distinctive styling, and high quality - all essentials that are traditional to our vehicles. This is a specialized utility vehicle designed for both on-road and off-roa...

  • Page 5

    Note: after you read the manual, it should be stored in the vehicle for convenient referencing and remain with the vehicle when sold, so that the new owner will be aware of all safety warnings. When it comes to service, remember that your authorized dealer knows your vehicle best, has factory-traine...

  • Page 6

    Failure to use driver and passenger seat belts provided is a major cause of severe or fatal injury. In fact, the u.S. Government notes that the universal use of existing seat belts could cut the highway death toll by 10,000 or more each year and could reduce disabling injuries by two million annuall...

  • Page 7

    1 introduction 7.

  • Page 8

    Warnings and cautions this owner’s manual contains warnings against op- erating procedures that could result in an accident or bodily injury. It also contains cautions against proce- dures that could result in damage to your vehicle. If you do not read this entire manual, you may miss important info...

  • Page 9

    Vehicle modifications/alterations warning! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death. 1 introduction 9.

  • Page 11: Contents

    Things to know before starting your vehicle contents 䡵 a word about your keys . . . . . . . . . . . . . . . . . 14 ▫ wireless ignition node (win) . . . . . . . . . . . . 14 ▫ integrated ignition key . . . . . . . . . . . . . . . . . 15 ▫ ignition key removal . . . . . . . . . . . . . . . . . . 15 ▫ ...

  • Page 12

    ▫ remote open window feature — if equipped . . . . . . . . . . . . . . . . . . . . . . . . . 23 ▫ using the panic alarm . . . . . . . . . . . . . . . . . 24 ▫ programming additional transmitters . . . . . . 24 ▫ transmitter battery service . . . . . . . . . . . . . . 24 ▫ general information . . . ....

  • Page 13

    ▫ enhanced seat belt use reminder system (beltalert 威) . . . . . . . . . . . . . . . . . . . . . . . . . 44 ▫ seat belts and pregnant women . . . . . . . . . . 45 ▫ seat belt extender . . . . . . . . . . . . . . . . . . . . . 46 ▫ supplemental restraint systems (srs) . . . . . . 46 ▫ advanced front ...

  • Page 14

    A word about your keys your vehicle uses a keyless ignition system. This system consists of a remote keyless entry (rke) transmitter with integrated ignition key and a wireless ignition node (win) with integral ignition switch. You can insert the double-sided key into the ignition switch with either...

  • Page 15

    Integrated ignition key the integrated ignition key operates the ignition switch. It also contains the remote keyless entry (rke) trans- mitter and an emergency key, which stores in the rear of the rke transmitter. The emergency key allows for entry into the vehicle should the battery in the vehicle...

  • Page 16

    Note: • if you try to remove the key before you place the shift lever in park, it may become trapped temporarily in the ignition switch. If this occurs, rotate the key to the right slightly, then remove the key as described. If a malfunction occurs, the system will trap the key in the ignition switc...

  • Page 17

    Key-in-ignition reminder if you open the driver’s door with the integrated ignition key in the ignition, a chime will sound to remind you to remove the key. Note: the key-in-ignition reminder only sounds when the integrated ignition key is placed in the lock or acc position. Sentry key 姞 the sentry ...

  • Page 18

    Note: the sentry key 威 immobilizer system is not compatible with aftermarket remote starting systems. Use of these systems may result in vehicle starting problems and loss of security protection. All of the rke transmitters provided with your new vehicle have been programmed to the vehicle electroni...

  • Page 19

    General information the sentry key 威 system complies with fcc rules part 15 and with rss-210 of industry canada. Operation is subject to the following conditions: • this device may not cause harmful interference. • this device must accept any interference that may be received, including interference...

  • Page 20

    Vehicle security light (located in the instrument cluster) will flash rapidly for about 16 seconds to signal that the vehicle security alarm is arming. During this 16 second arming period, opening any door or the liftgate will cancel the arming. If the vehicle security alarm success- fully arms, the...

  • Page 21

    Remote keyless entry (rke) this system allows you to lock or unlock the doors and liftgate, or activate the panic alarm, from distances up to approximately 66 ft (20 m) using a hand-held remote keyless entry (rke) transmitter. The rke transmitter does not need to be pointed at the vehicle to activat...

  • Page 22

    Remote key unlock, driver door/all doors first press this feature lets you program the system to unlock either the driver’s door or all doors, on the first press of the unlock button on the rke transmitter. To change the current setting, proceed as follows: • for vehicles equipped with the electroni...

  • Page 23

    To lock the doors press and release the lock button on the rke transmit- ter to lock all doors. The turn signal lamps will flash and the horn will chirp to acknowledge the signal. Sound horn with remote key lock this feature will cause the horn to chirp when the doors are locked with the rke transmi...

  • Page 24

    Using the panic alarm to turn the panic alarm feature on or off, press and hold the panic button on the rke transmitter for at least one second and release. When the panic alarm is on, the headlights and park lamps will flash, the horn will pulse on and off, and the interior lights will turn on. The...

  • Page 25

    2. Remove and replace the battery. Avoid touching the new battery with your fingers. Skin oils may cause battery deterioration. If you touch a battery, clean it with rubbing alcohol. 3. Reposition the access door panel over the battery opening and snap into place. General information this device com...

  • Page 26

    If your rke transmitter fails to operate from a normal distance, check for these two conditions: 1. A weak battery in the rke transmitter. The expected life of the battery is a minimum of three years. 2. Closeness to a radio transmitter such as a radio station tower, airport transmitter, and some mo...

  • Page 27

    Warning! • do not start or run an engine in a closed garage or confined area. Exhaust gas contains carbon mon- oxide (co) which is odorless and colorless. Car- bon monoxide is poisonous and can cause serious injury or death when inhaled. • keep remote keyless entry (rke) transmitters away from child...

  • Page 28

    Note: to avoid unintentional shutdowns, the system will disable the one time press of the remote start button for two seconds after receiving a valid remote start request. To exit remote start mode and drive the vehicle before the end of 15 minute cycle, press and release the unlock button on the rk...

  • Page 29

    Power door locks the power door lock switch is located on each front door panel. Press the switch to lock or unlock the doors. If the plunger is down when the door is closed, the door will lock. Therefore, make sure the key is not inside the vehicle before closing the door. If you press the door loc...

  • Page 30

    This feature is selectable and can be turned on or off. Refer to “auto door locks” under “customer- programmable features” in the “electronic vehicle infor- mation center (evic),” in section 4 of this manual, or see your authorized dealer. Child protection door lock the rear doors of your vehicle ar...

  • Page 31

    Windows power windows the power window controls are located on the driver’s door trim panel. There is a single switch on the front passenger door/rear doors which operates the front passenger/rear passenger door windows. The window controls will operate only when the ignition switch is in the on or ...

  • Page 32

    Auto-down both the driver and front passenger window switches have an “auto-down” feature. Press the window switch past the first detent, release, and the window will go down automatically. To cancel the “auto-down” move- ment, operate the switch in either the up or down direction and release the sw...

  • Page 33

    Resetting the auto up feature should the auto up feature stop working, the window probably needs to be reset. To reset auto up: pull the window switch up and close the window com- pletely, then pull and hold the switch for one second. Window lockout button the window lockout button on the driver’s d...

  • Page 34

    Wind buffeting wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions. This is a normal occur- rence and ...

  • Page 35

    Liftgate flipper glass the liftgate flipper glass is also unlocked when the liftgate is unlocked. To open the flipper glass, push up on the window switch located on the liftgate. Warning! To avoid injury, stand back when opening. Glass may automatically rise. Once the liftgate flipper glass has been...

  • Page 36

    Warning! Driving with the flipper glass open can allow poi- sonous exhaust gases into your vehicle. You and your passengers could be injured by these fumes. Keep the flipper glass closed when you are operating the vehicle. Occupant restraints some of the most important safety features in your vehicl...

  • Page 37

    Note: the advanced front airbags have a multistage inflator design. This allows the airbag to have different rates of inflation based on severity and type of collision. Please pay close attention to the information in this section. It tells you how to use your restraint system properly, to keep you ...

  • Page 38

    Warning! • it is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seri- ously injured or killed. • wearing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your...

  • Page 39

    2. The seat belt latch plate is above the back of your seat. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to make the belt go around your lap. 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “cli...

  • Page 40

    Warning! • a belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • a belt that is too loose will not protect you as well. In a sudden stop ...

  • Page 41

    4. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap portion, pull up a bit on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision. Wa...

  • Page 42

    Warning! A frayed or torn belt could rip apart in a collision and leave you with no protection. Inspect the belt system periodically, checking for cuts, frays, or loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Seat belt assemblies must be replaced a...

  • Page 43

    Energy management feature this vehicle has a safety belt system with an energy management feature in the front seating positions to help further reduce the risk of injury in the event of a head-on collision. This safety belt system has a retractor assembly that is designed to release webbing in a co...

  • Page 44

    How to disengage the automatic locking mode disconnect the combination lap/shoulder belt and allow it to retract completely to disengage the automatic locking mode and activate the vehicle sensitive (emer- gency) locking mode. Seat belt pretensioners — if equipped the driver and front passenger seat...

  • Page 45

    Beltalert 威 can be enabled or disabled by your authorized dealer or by following these steps: note: the following steps must occur within the first 60 seconds of the ignition switch being turned to the on or start position. Chrysler group llc does not recom- mend deactivating beltalert 威. 1. Turn th...

  • Page 46

    Seat belt extender if a seat belt is too short, even when fully extended and when the adjustable upper shoulder belt anchorage (if equipped) is in its lowest position, your authorized dealer can provide you with a seat belt extender. This extender should be used only if the existing belt is not long...

  • Page 47

    Note: these airbags are certified to the new federal regulations for advanced airbags. The advanced front airbags have a multistage inflator design. This allows the airbag to have different rates of inflation based on the severity and type of collision. This vehicle may also be equipped with supplem...

  • Page 48

    • front passenger airbag • front and side impact sensors • steering wheel and column • instrument panel • knee impact bolster • front seat belt pretensioners — if equipped • supplemental side airbag inflatable curtains (sabic) — if equipped advanced front airbag features the advanced front airbag sy...

  • Page 49

    Warning! (continued) • do not mount any accessories to the knee bolster such as alarm lights, stereos, citizen band radios, etc. Supplemental side airbag inflatable curtain (sabic) — if equipped sabic airbags offer side-impact and vehicle rollover protection to front and rear seat outboard occupants...

  • Page 50

    • airbag covers may not be obvious in the interior trim; but they will open during airbag deployment. The system includes sensors adjacent to both front and rear seat occupants that are calibrated to deploy the sabic airbags during impacts that require airbag occu- pant protection. Warning! • if you...

  • Page 51

    Warning! Infants in rear-facing child restraints should never ride in the front seat of a vehicle with a passenger front airbag. An airbag deployment can cause severe injury or death to infants in that position. Children that are not big enough to wear the vehicle seat belt properly (see section on ...

  • Page 52

    Warning! • relying on the airbags alone could lead to more severe injuries in a collision. The airbags work with your seat belt to restrain you properly. In some collisions, the airbags won’t deploy at all. Always wear your seat belts even though you have airbags. • being too close to the steering w...

  • Page 53

    The advanced front airbags will not deploy in all frontal collisions, including some that may produce substantial vehicle damage — for example, some pole collisions, truck underrides, and angle offset collisions. On the other hand, depending on the type and location of impact, advanced front airbags...

  • Page 54

    It also includes diagnostics that will illuminate the instru- ment cluster airbag warning light if a malfunction is noted. The diagnostics also record the nature of the malfunction. Warning! Ignoring the airbag warning light in your instru- ment panel could mean you won’t have the airbags to protect...

  • Page 55

    Deploy the sabic airbags, depending on severity and type of collision. In these events, the orc will deploy the sabic only on the impact side of the vehicle. A quantity of non-toxic gas is generated to inflate the side curtain airbag. The inflating side curtain airbag pushes the outside edge of the ...

  • Page 56

    • turn on the interior lights, which remain on as long as the battery has power or until the ignition key is removed. • unlock the doors automatically. If a deployment occurs the airbags are designed to deflate immediately after deployment. Note: front and/or side airbags will not deploy in all coll...

  • Page 57

    Warning! Deployed airbags and seat belt pretensioners cannot protect you in another collision. Have the airbags, seat belt pretensioners, and the front passenger seat belt retractor assembly replaced by an authorized dealer as soon as possible. Also, have the occupant restraint controller (orc) syst...

  • Page 58

    Warning! (continued) • do not attempt to modify any part of your ad- vanced airbag system. The airbag may inflate accidentally or may not function properly if modi- fications are made. Take your vehicle to an autho- rized dealer for any advanced airbag system ser- vice. If your seat, including your ...

  • Page 59

    Located on the inside of the fuse block cover for the proper airbag fuses. See your authorized dealer if the fuse is good. Event data recorder (edr) in the event of an accident, your vehicle is designed to record up to five seconds of specific vehicle data param- eters (see list below) in an event d...

  • Page 60

    Accessing the electronic data stored, unless ordered to download data by a court with legal jurisdiction (i.E., pursuant to a warrant). A copy of the data will be provided to the custodial entity upon request. General data that does not identify particular vehicles or crashes may be released for inc...

  • Page 61

    Child restraints everyone in your vehicle needs to be buckled up all the time, including babies and children. Every state in the united states, and all canadian provinces, require that small children ride in proper restraint systems. This is the law, and you can be prosecuted for ignoring it. Childr...

  • Page 62

    • the infant carrier is only used rearward-facing in the vehicle. It is recommended for children who weigh up to about 20 lbs (9 kg). Convertible child seats often have a higher weight limit in the rearward-facing direction than infant carriers do, so they can be used rearward-facing by children who...

  • Page 63

    Standards. Chrysler group llc also recommends that you try a child restraint in the vehicle seats where you will use it before you buy it. • the restraint must be appropriate for your child’s weight and height. Check the label on the restraint for weight and height limits. • carefully follow the ins...

  • Page 64

    • if the belt still cannot be tightened, or if pulling and pushing on the restraint loosens the belt, disconnect the latch plate from the buckle, turn the buckle around, and insert the latch plate into the buckle again. If you still cannot make the child restraint secure, try a different seating pos...

  • Page 65

    Children too large for booster seats children who are large enough to wear the shoulder belt comfortably, and whose legs are long enough to bend over the front of the seat when their back is against the seatback, should use the lap/shoulder belt in a rear seat. • make sure that the child is upright ...

  • Page 66

    Strap kits or retro-fit kits. You are urged to take advantage of all the available attachments provided with your child restraint in any vehicle. Note: when using the latch attaching system to install a child restraint, please ensure that all seat belts not being used for occupant restraints are sto...

  • Page 67

    The rear seat lower anchorages are round bars, located at the rear of the seat cushion where it meets the seatback, and are just visible when you lean into the rear seat to install the child restraint. You will easily feel them if you run your finger along the intersection of the seatback and seat c...

  • Page 68

    Means of adjusting the tension in the strap. Forward- facing toddler restraints and some rear-facing infant restraints will also be equipped with a tether strap, a hook for attachment to the tether strap anchorage and a means of adjusting the tension of the strap. First, loosen the adjusters on the ...

  • Page 69

    For seat belts having an automatic locking retractor (alr), pull the belt from the retractor until there is enough allowance to pass it through the child restraint and slide the latch plate into the buckle. Then, pull the belt until it is fully extended from the retractor. Allow the belt to return i...

  • Page 70

    Warning! Always remove the subwoofer from the vehicle whenever the tether anchors behind the subwoofer are required for proper installation of a child re- straining device. In the event of an accident, or under severe vehicle maneuvers, leaving the subwoofer unsecured in the vehicle could result in ...

  • Page 71

    Warning! An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchor positions directly behind the child seat to secure a child restraint top tether strap. Transporting pets airbags deploying in the front seat could harm your pet. An...

  • Page 72

    A new engine may consume some oil during its first few thousand miles (kilometers) of operation. This should be considered a normal part of the break-in and not inter- preted as an indication of difficulty. Safety tips transporting passengers never transport passengers in the cargo area. Warning! • ...

  • Page 73

    Do not run the engine in a closed garage or in confined areas any longer than needed to move your vehicle in or out of the area. If it is necessary to sit in a parked vehicle with the engine running, adjust your heating or cooling controls to force outside air into the vehicle. Set the blower at hig...

  • Page 74

    Airbag warning light the light should come on and remain on for six to eight seconds as a bulb check when the ignition switch is first turned on. If the light is not lit during starting, see your authorized dealer. If the light stays on, flickers, or comes on while driving, have the system checked b...

  • Page 75: Contents

    Understanding the features of your vehicle contents 䡵 mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 ▫ inside day/night mirror . . . . . . . . . . . . . . . . 80 ▫ automatic dimming mirror — if equipped . . . 81 ▫ outside mirrors . . . . . . . . . . . . . . . . . . . . . . 81...

  • Page 76

    ▫ four-way passenger’s power seat — if equipped . . . . . . . . . . . . . . . . . . . . . . . . . 87 ▫ head restraints . . . . . . . . . . . . . . . . . . . . . . 88 ▫ front heated seats — if equipped . . . . . . . . . 89 ▫ rear heated seats — if equipped . . . . . . . . . . 90 ▫ 60/40 split rear se...

  • Page 77

    ▫ fog lights — if equipped . . . . . . . . . . . . . . 106 ▫ turn signals . . . . . . . . . . . . . . . . . . . . . . . . 107 ▫ lane change assist . . . . . . . . . . . . . . . . . . . 108 ▫ high/low beam switch . . . . . . . . . . . . . . . 108 ▫ flash-to-pass . . . . . . . . . . . . . . . . . . . ...

  • Page 78

    ▫ enable/disable the rear park assist . . . . . . 122 ▫ service the rear park assist . . . . . . . . . . . . 122 ▫ cleaning the rear park assist . . . . . . . . . . . 123 ▫ system usage precautions . . . . . . . . . . . . . . 123 䡵 rear camera — if equipped . . . . . . . . . . . . . . 126 ▫ turning ...

  • Page 79

    ▫ sunshade operation . . . . . . . . . . . . . . . . . . 137 ▫ wind buffeting . . . . . . . . . . . . . . . . . . . . . . 137 ▫ sunroof maintenance . . . . . . . . . . . . . . . . . 137 ▫ ignition off operation . . . . . . . . . . . . . . . . . 138 ▫ sunroof fully closed . . . . . . . . . . . . . . ...

  • Page 80

    Mirrors inside day/night mirror a two-point pivot system allows for horizontal and vertical adjustment of the mirror. The mirror should be adjusted to center on the view through the rear window. Headlight glare from vehicles behind you can be reduced by moving the small control under the mirror to t...

  • Page 81

    Automatic dimming mirror — if equipped this mirror automatically adjusts for headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light next to the button will illuminate to indicate when the dimming feature is activated. Ca...

  • Page 82

    Warning! Vehicles and other objects seen in the passenger-side convex mirror will look smaller and farther away than they really are. Relying too much on your passenger-side convex mirror could cause you to collide with another vehicle or other object. Use your inside mirror when judging the size or...

  • Page 83

    After selecting a mirror, move the knob in the same direction you want the mirror to move. Use the off (center) position to guard against accidentally moving a mirror position. Power mirror preselected positions can be controlled by the optional memory seat feature. Refer to “driver memory seat” in ...

  • Page 84

    Lift the cover to reveal the mirror. The light will turn on automatically. Sun visor extension — if equipped this feature has a pull out extension on the sun visor for increased coverage. Uconnect™ phone — if equipped refer to “uconnect™ phone” in the uconnect™ user manual located on the dvd for fur...

  • Page 85

    Warning! • do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. In a collision, people riding in these areas are more likely to be seriously injured or killed. • be sure everyone in your vehicle is in a seat and using a seat belt properly. Front man...

  • Page 86

    Warning! Do not ride with the seatback reclined so that the seat belt is no longer resting against your chest. In a collision, you could slide under the seat belt and be seriously or even fatally injured. Use the recliner only when the vehicle is parked. Manual lumbar support adjustment the manual l...

  • Page 87

    Eight-way driver’s power seat the driver’s power seat switches are located on the outboard side of the driver’s seat. The bottom switch controls up/down, forward/rearward and tilt adjust- ment. The top switch controls the seatback recline adjust- ment. Warning! Adjusting a seat while the vehicle is ...

  • Page 88

    Note: the four-way seat does not have an up/down adjustment. Warning! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust any seat only while the vehi...

  • Page 89

    Warning! Driving a vehicle with the head restraints removed or improperly adjusted could cause serious injury or death in the event of a collision. The head restraints should always be checked prior to operating the vehicle and never adjusted while the vehicle is in motion. Always adjust the head re...

  • Page 90

    Note: once a heat setting is selected, heat will be felt within two to five minutes. Warning! • persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, ex- haustion or other physical conditions must exer- cise c...

  • Page 91

    After turning the ignition on, you can choose from high, low or off heat settings. Amber indicator lights in each switch indicate the level of heat in use. Two indicator lights will illuminate for high, one for low and none for off. Press the switch once to select high-level heat- ing. Press the swi...

  • Page 92

    Warning! • persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, ex- haustion or other physical conditions must exer- cise care when using the seat heater. It may cause burns even at low temperatures, especial...

  • Page 93

    1. Pull the release strap (toward the front of the vehicle) to release. Note: do not fold the rear seat down with the center seat belt buckled. 2. Fold the rear seat completely forward. Rear seat release rear seat folded 3 understanding the features of your vehicle 93.

  • Page 94

    To raise rear seat raise the rear seatback and lock it into place. If interfer- ence from the cargo area prevents the seatback from fully locking, you will have difficulty returning the seat to its proper position. Warning! The cargo area in the rear of the vehicle (with the rear seatbacks in the lo...

  • Page 95

    Press the latch and lift the top of the armrest to access the storage bin. Driver memory seat — if equipped once programmed, the memory buttons 1 and 2 on the driver’s door panel can be used to recall the driver’s seat, driver’s outside mirror, adjustable brake and accelerator pedals and radio stati...

  • Page 96

    Your vehicle is equipped with two rke transmitters. One or both rke transmitters can be linked to either memory position. The memory system can accommodate up to four rke transmitters, each one linked to either of the two memory positions. Setting memory positions and linking remote keyless entry tr...

  • Page 97

    10. Insert the ignition key, and turn the ignition switch to the on position. 11. Select ⬙remote linked to memory⬙ in the electronic vehicle information center (evic) and enter ⬙yes⬙. Refer to “electronic vehicle information center (evic) — customer-programmable features” in section 4 for more infor...

  • Page 98

    To disable a rke transmitter linked to memory 1. Turn the ignition switch to the lock position, and remove the key. 2. Press and release memory button number 1. The system will recall any memory settings stored in position 1. Wait for the system to complete the memory recall before continuing to ste...

  • Page 99

    • the seat will move to the position located 0.3 in (8 mm) forward of the rear stop if the starting position is between 0.9 to 2.67 in (23 to 68 mm) forward of the rear stop when the key is removed from the ignition switch. The seat will move forward to the memory/ driving position when the key is p...

  • Page 100

    To open and close the hood to open the hood, two latches must be released. 1. Pull the release lever located below the instrument panel and in front of the driver’s door. 2. Reach under the hood, move safety latch to the left and lift the hood. Caution! To prevent possible damage, do not slam the ho...

  • Page 101

    Warning! If the hood is not fully latched, it could fly up when the vehicle is moving and block your forward vision. Be sure all hood latches are fully latched before driving. Lights multifunction lever the multifunction lever controls the operation of the headlights, turn signals, headlight beam se...

  • Page 102

    Headlights and parking lights turn the end of the multifunction lever to the first detent for parking light operation. Turn to the second detent for headlight operation. Turn to the third detent for auto- matic headlight operation (if equipped). Automatic headlight system — if equipped turn the end ...

  • Page 103

    Headlights on automatically with wipers if your vehicle is equipped with automatic headlights, it also has this customer-programmable feature. When your headlights are in the automatic mode and the engine is running, they will automatically turn on when the wiper system is on. Refer to “headlamps on...

  • Page 104

    To activate 1. Select “auto high beams.” refer to “electronic ve- hicle information center (evic) customer- programmable features” in section 4 of this manual. 2. Turn the end of the multifunction lever to the auto headlight position. 3. Push the multifunction lever away from you (toward front of ve...

  • Page 105

    Automatic headlight leveling — hid headlights only this feature prevents the headlights from interfering with the vision of oncoming drivers. Headlight leveling automatically adjusts the height of the headlight beam in reaction to changes in vehicle pitch. Instrument panel and interior lights when t...

  • Page 106

    Battery saver feature if the multifunction lever is left in the interior light position, parking light position, or the headlight position when the ignition switch is moved to the lock position, the battery saver feature will automatically turn off the exterior and interior lights after eight minute...

  • Page 107

    Note: • turning on the high beam headlights turns off the fog lights. • a front fog light is a lighting device that provides illumination in front of the vehicle under conditions of fog, rain, snow, or dust. The front fog lights supple- ment the low beams of a standard headlight system. • proper aim...

  • Page 108

    Lane change assist tap the lever up or down once, without moving beyond the detent, and the turn signal (right or left) will flash three times then automatically turn off. High/low beam switch push the multifunction lever away from you to switch the headlights to high beam. Pull the multifunction le...

  • Page 109

    Lens a second time. There are also reading lights located above the rear doors. Each light can be turned on by pressing the front recessed area of the lens. To turn these lights off, press the recessed area of the lens a second time. Windshield wipers and washers the windshield wiper/washer control ...

  • Page 110

    Windshield wiper operation rotate the end of the lever upward to the lo position for low-speed wiper operation. Rotate the end of the lever upward to the hi position for high-speed wiper operation. Caution! Always remove any buildup of snow that prevents the windshield wiper blades from returning to...

  • Page 111

    Warning! Sudden loss of visibility through the windshield could lead to an accident. You might not see other vehicles or other obstacles. To avoid sudden icing of the windshield during freezing weather, warm the windshield with the defroster before and during windshield washer use. Mist use the mist...

  • Page 112

    Delay interval. The delay can be regulated from a maxi- mum of approximately 18 seconds between cycles, to a cycle every 1/2 second. Note: the wiper delay times depend on vehicle speed. If the vehicle is moving less than 10 mph (16 km/h), delay times will be doubled. Rain sensing wipers — if equippe...

  • Page 113

    Note: • the rain sensing feature will not operate when the wiper switch is in the low or high-speed position. • the rain sensing feature may not function properly when ice, or dried salt water is present on the wind- shield. • use of rain-x威 or products containing wax or silicone may reduce rain sen...

  • Page 114

    Tilt/telescoping steering column this feature allows you to tilt the steering column upward or downward. It also allows you to lengthen or shorten the steering column. The tilt/telescoping control handle is located below the steering wheel at the end of the steering column. To unlock the steering co...

  • Page 115

    Improved position with the steering wheel. The adjust- able pedal system is designed to allow a greater range of driver comfort for steering wheel tilt and seat position. The position of the brake and accelerator pedals can be adjusted without compromising safety or comfort in actuating the pedals. ...

  • Page 116

    Caution! Do not place any article under the adjustable pedal’s or impede its ability to move as it may cause damage to the pedal controls. Pedal travel may become lim- ited if movement is stopped by an obstruction in the adjustable pedal’s path. Warning! Do not adjust the pedals while the vehicle is...

  • Page 117

    Note: in order to ensure proper operation, the elec- tronic speed control system has been designed to shut down if multiple speed control functions are operated simultaneously. If this occurs, the electronic speed con- trol system can be reactivated by pushing the electronic speed control on/off but...

  • Page 118

    Speed control without erasing the set speed memory. Pressing the on/off button or turning the ignition switch off erases the set speed memory. To resume speed to resume a previously set speed, push the resume accel lever up and release. Resume can be used at any speed above 20 mph (32 km/h). To vary...

  • Page 119

    On steep hills, a greater speed loss or gain may occur so it may be preferable to drive without electronic speed control. Rear park assist — if equipped the rear park assist provides visible and audible indi- cations of the distance between the rear fascia and the detected obstacle when backing up. ...

  • Page 120

    Rear park assist warning display the rear park assist warning display, located in the headliner near the flipper glass, provides both visible and audible warnings to indicate the distance between the rear fascia and the detected obstacle. When the ignition is turned to the on position, the warning d...

  • Page 121

    Warning display distances display led obstacle distance from: led color audible signal rear corners rear center 1st led 59 in (150 cm) yellow yes, half second 2nd led 51 in (130 cm) yellow none 3rd led 45 in (115 cm) yellow none 4th led 31.5 in (80 cm) 39 in (100 cm) yellow none 5th led 25.5 in (65 ...

  • Page 122

    Enable/disable the rear park assist the rear park assist can be enabled and disabled with a switch located on the upper switch bank of the instru- ment panel. Press the switch once to turn the rear park assist on, push the switch a second time to turn the rear park assist off. When the switch is pre...

  • Page 123

    Cleaning the rear park assist clean the rear park assist sensors with water, car wash soap and a soft cloth. Do not use rough or hard cloths. Do not scratch or poke the sensors. Otherwise, you could damage the sensors. System usage precautions note: • ensure that the rear bumper is free of dirt and ...

  • Page 124

    • clean the rear park assist sensors regularly, taking care not to scratch or damage them. The sensors must not be covered with ice, snow, slush, mud, dirt, or debris. Failure to do so can result in the system not working properly. The system might not detect an obstacle behind the fascia/bumper, or...

  • Page 125

    Warning! • drivers must be careful when backing up even when using the rear park assist system. Always check carefully behind your vehicle, look behind you, and be sure to check for pedestrians, animals, other vehicles, obstructions, and blind spots be- fore backing up. You are responsible for safet...

  • Page 126

    Rear camera — if equipped vehicles may be equipped with a rearview camera (lo- cated on the rear liftgate) that allows you to see an on-screen image (on the navigation/multimedia radio) of the rear of your vehicle, whenever the vehicle is put into reverse. Warning! Drivers must be careful when backi...

  • Page 127

    Turning the rear camera on or off — with navigation radio 1. Press the ⬙menu⬙ hard key. 2. Select ⬙system setup⬙ soft key. 3. Press the “camera setup” soft key. 4. Enable or disable the rear camera feature by selecting ⬙enable rear camera in reverse⬙ soft key. 5. Press the “save” soft key. 6. When t...

  • Page 128

    Overhead console the overhead console contains courtesy/reading lights, storage for sunglasses. Universal garage door opener (homelink 威) and power sunroof switches may also be included, if equipped. Courtesy/reading lights at the forward end of the console are two courtesy/ reading lights. Press th...

  • Page 129

    Garage door opener — if equipped homelink 威 replaces up to three remote controls (hand- held transmitters) that operate devices such as garage door openers, motorized gates, lighting or home security systems. The homelink 威 unit operates off your vehicle’s battery. The homelink 威 buttons are located...

  • Page 130

    Warning! • your motorized door or gate will open and close while you are training the universal transceiver. Do not train the transceiver if people or pets are in the path of the door or gate. Only use this trans- ceiver with a garage door opener that has a “stop and reverse” feature as required by ...

  • Page 131

    2. Place the hand-held transmitter 1 to 3 in (3 to 8 cm) from the homelink 威 buttons while keeping the evic display in view. For optimal training, point the battery end of the hand- held transmitter away from the homelink 威. 3. Simultaneously, press and hold both the chosen homelink 威 button and the...

  • Page 132

    This can usually be found where the hanging antenna wire is attached to the garage door opener motor (it is not the button normally used to open and close the door). 6. Firmly press and release the “learn” or “train- ing” button. The name and color of the button may vary by manufacturer. Note: there...

  • Page 133

    Gate operator/canadian programming canadian radio-frequency laws require transmitter sig- nals to “time-out” (or quit) after several seconds of transmission – which may not be long enough for homelink 威 to pick up the signal during programming. Similar to this canadian law, some u.S. Gate operators ...

  • Page 134

    Reprogramming a single homelink 姞 button to reprogram a channel that has been previously trained, follow these steps: 1. Turn the ignition switch to the on/run position. 2. Press and hold the desired homelink 威 button for 20 seconds until the evic display states “channel # training.” do not release ...

  • Page 135

    General information this device complies with fcc rules part 15 and industry canada rss-210. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference that may be received including interference that may cause...

  • Page 136

    Warning! • never leave children in a vehicle with the key in the ignition switch. Occupants, particularly unat- tended children, can become entrapped by the power sunroof while operating the power sunroof switch. Such entrapment may result in serious injury or death. • in an accident, there is a gre...

  • Page 137

    Pinch protect override if a known obstruction (ice, debris, etc.) prevents closing the sunroof, press the switch forward and hold for two seconds after the reversal occurs. This allows the sunroof to move toward the closed position. Note: pinch protection is disabled while the switch is pressed. Ven...

  • Page 138

    Ignition off operation the power sunroof switches remain active for up ap- proximately ten minutes after the ignition switch has been turned off. Opening either front door will cancel this feature. Sunroof fully closed press the switch forward and release to ensure that the sunroof is fully closed. ...

  • Page 139

    The front power outlets are located to the left and right of the convenience tray (lower center of instrument panel). Pull lightly on the tab of the plastic cover to access these power outlets. The power outlet located on the left side of the tray can be used to power a conventional cigar lighter. T...

  • Page 140

    Warning! To avoid serious injury or death: • do not insert any objects into the receptacles. • do not touch with wet hands. • close the lid when not in use and while driving the vehicle. • if this outlet is mishandled, it may cause an electric shock and failure. Caution! • many accessories that can ...

  • Page 141

    The power inverter is designed with built-in overload protection. If the power rating of 150 watts is exceeded, the power inverter will automatically shut down. Once the electrical device has been removed from the outlet the inverter should automatically reset. If the power rating exceeds approximat...

  • Page 142

    Note: when the power inverter switch is pressed, there will be a delay of approximately one second before the inverter status indicator turns on. The status indica- tor of the ac power inverter indicates whether the inverter is producing ac power. Warning! To avoid serious injury or death: • do not ...

  • Page 143

    The rear passengers have access to two cupholders that pull out from the lower center of the rear seat. Cargo area features cargo light the cargo area light is activated by opening the liftgate, opening any door, or by rotating the dimmer control on the multifunction lever to the extreme top positio...

  • Page 144

    Rear storage compartment the rear storage compartment is located on the driver’s side behind the second row seat. Retractable cargo area cover — if equipped note: the purpose of this cover is for privacy, not to secure loads. It will not prevent cargo from shifting or protect passengers from loose c...

  • Page 145

    Warning! In an accident, a loose cargo cover in the vehicle could cause injury. It could fly around in a sudden stop and strike someone in the vehicle. Do not store the cargo cover on the cargo floor or in the passenger compartment. Remove the cover from the vehicle when taken from its mounting. Do ...

  • Page 146

    Cargo tie-down hooks the cargo tie-downs, located on the cargo area floor, should be used to safely secure loads when the vehicle is moving. Warning! • to help protect against personal injury, passengers should not be seated in the rear cargo area. The rear cargo space is intended for load carrying ...

  • Page 147

    Warning! (continued) • do not carry loads which exceed the load limits described on the label attached to the left door or left door center pillar. • always place cargo evenly on the cargo floor. Put heavier objects as low and as far forward as possible. • place as much cargo as possible in front of...

  • Page 148

    The cargo load floor is held by spring loaded latches. In order to use the cargo load floor, use the following procedure: note: the cargo load floor latches should not be used as cargo tie-downs. 1. Flip up the pull loop(s) so they are perpendicular (straight up) to the top surface of the tray. 2. P...

  • Page 149

    Rotate the switch upward to the “on” position to activate the rear wiper. Note: the rear wiper operates in an intermittent mode only. Rotate the switch upward to the “washer” position to activate that rear washer. The washer pump will continue to operate as long as the lever or ring is engaged. Upon...

  • Page 150

    Caution! Failure to follow these cautions can cause damage to the heating elements: • use care when washing the inside of the rear window. Do not use abrasive window cleaners on the interior surface of the window. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements....

  • Page 151

    Parallel to the rack frame. Once the crossbar is in one of the seven detent positions, retighten the thumb screws to lock the crossbar into position. Note: • to help control wind noise when the crossbars are not in use, place the front crossbar in the second detent from the front of the vehicle and ...

  • Page 152

    Caution! (continued) • travel at reduced speeds and turn corners care- fully when carrying large or heavy loads on the roof rack. Wind forces, due to natural causes or nearby truck traffic, can add sudden upward lift to a load. This is especially true on large flat loads and may result in damage to ...

  • Page 153: Contents

    Understanding your instrument panel contents 䡵 instrument panel features . . . . . . . . . . . . . . . 156 䡵 instrument cluster . . . . . . . . . . . . . . . . . . . . 157 䡵 instrument cluster description . . . . . . . . . . . . 158 䡵 electronic vehicle information center (evic) . . 168 ▫ electronic...

  • Page 154

    䡵 sales code res — am/fm stereo radio with cd player (mp3 aux jack) . . . . . . . . . . . . . . . 185 ▫ operating instructions — radio mode . . . . . 186 ▫ operation instructions — cd mode for cd and mp3 audio play . . . . . . . . . . . . . . . . . 189 ▫ notes on playing mp3 files . . . . . . . . . ...

  • Page 155

    ▫ selecting uconnect™ studios (satellite) mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 212 ▫ satellite antenna . . . . . . . . . . . . . . . . . . . . . 212 ▫ reception quality . . . . . . . . . . . . . . . . . . . . 213 ▫ operating instructions - uconnect™ studios (satellite) mode...

  • Page 156

    Instrument panel features 1 — air outlet 5 — upper switch bank 9 — lower switch bank 2 — instrument cluster 6 — power outlet/cigar lighter 10 — climate controls 3 — radio 7 — storage bin 11 — ignition switch 4 — glove compartment 8 — power outlet 12 — storage bin 156 understanding your instrument pa...

  • Page 157

    Instrument cluster 4 understanding your instrument panel 157.

  • Page 158

    Instrument cluster description 1. Speedometer indicates vehicle speed. 2. Brake warning light this light monitors various brake functions, including brake fluid level and parking brake application. If the brake light turns on, it may indicate that the parking brake is applied, that the brake fluid l...

  • Page 159

    Warning! Driving a vehicle with the red brake light on is dangerous. Part of the brake system may have failed. It will take longer to stop the vehicle. You could have an accident. Have the vehicle checked immediately. Vehicles equipped with the anti-lock brake system (abs), are also equipped with el...

  • Page 160

    The on position before engine start. If the bulb does not come on when turning the key from off to on, have the condition checked promptly. Certain conditions such as a loose or missing gas cap, poor fuel quality, etc., may illuminate the light after engine start. The vehicle should be serviced if t...

  • Page 161

    7. Anti-lock brake (abs) light this light monitors the anti-lock brake system (abs). The light will turn on when the ignition switch is turned to the on position and may stay on for as long as four seconds. If the abs light remains on or turns on while driving, it indicates that the anti-lock portio...

  • Page 162

    11. Electronic stability program (esp) indicator light / traction control system (tcs) indicator light if this indicator light flashes during accelera- tion, apply as little throttle as possible. While driving, ease up on the accelerator. Adapt your speed and driving to the prevailing road con- diti...

  • Page 163

    Your vehicle has also been equipped with a tpms malfunction indicator to indicate when the system is not operating properly. The tpms malfunction indicator is combined with the low tire pressure telltale. When the system detects a malfunction, the telltale will flash for approximately one minute and...

  • Page 164

    The gauge pointer will likely indicate a higher tempera- ture when driving in hot weather, up mountain grades, or when towing a trailer. It should not be allowed to exceed the upper limits of the normal operating range. Caution! Driving with a hot engine cooling system could damage your vehicle. If ...

  • Page 165

    15. Tow/haul indicator light — if equipped this light will illuminate when the tow/ haul button has been selected. The tow/ haul button is located in the center of the instrument panel (below the climate controls). 16. Electronic stability program (esp) indicator light / brake assist system (bas) wa...

  • Page 166

    18. Seat belt reminder light when the ignition switch is first turned on, this light will turn on for five to eight seconds as a bulb check. During the bulb check, if the driver’s seat belt is unbuckled, a chime will sound. After the bulb check or when driving, if the driver or front passenger seat ...

  • Page 167

    22. Fuel gauge the pointer shows the level of fuel in the fuel tank when the ignition switch is in the on position. 23. Electronic throttle control (etc) warning light this light informs you of a problem with the electronic throttle control (etc) system. If a problem is detected the light will come ...

  • Page 168

    If jump starting is required, refer to “jump starting procedures” in section 6 of this manual. 26. Low fuel light this light will turn on, and a single chime will sound, when the fuel level drops to 1/8 tank. The low fuel warning light may turn on and off again, especially during and after hard brak...

  • Page 169

    • compass display • outside temperature display • trip computer functions the system allows the driver to select information by pressing the following buttons mounted on the steering wheel: menu button press and release the menu button and the mode displayed will change between trip functions, perso...

  • Page 170

    • damaged key — key does not communi- cate • key not programmed — key not pro- grammed • wrong key — key does not belong to vehicle • key not programmed — exceeded key pro- gram limit • programming active — new key pro- grammed • service security key • driver/passenger door open (with graphic) • lef...

  • Page 171

    • liftglass/hood open (with graphic) • washer fluid low (with graphic) • coolant low (with graphic) • oil change required • oil change reset • check gauges • auto high beams on • auto high beams off • park assist disabled • service suspension • service park assist system • transmission over temp • c...

  • Page 172

    • driver 1 memory • driver 2 memory • adj. Pedals disabled — cruise control set • adj. Pedals disabled — shifter in reverse • low tire pressure • check tpm system • left front low pressure (premium tpm sys- tem only) • right front low pressure (premium tpm sys- tem only) • left rear low pressure (pr...

  • Page 173

    Engine oil change indicator system oil change required (gasoline engines only) your vehicle is equipped with an engine oil change indicator system. The “oil change required” message will flash in the evic display for approximately 10 sec- onds after a single chime has sounded, to indicate the next s...

  • Page 174

    • display units of measure in press the scroll button to cycle through all the trip computer functions. The trip functions mode displays the following informa- tion: average fuel economy / fuel saver mode shows the average fuel economy since the last reset. When the fuel economy is reset, the displa...

  • Page 175

    Distance to empty (dte) shows the estimated distance that can be traveled with the fuel remaining in the tank. This estimated distance is determined by a weighted average of the instantaneous and average fuel economy, according to the current fuel tank level. Dte cannot be reset through the function...

  • Page 176

    Elapsed time shows the total elapsed time of travel since the last reset when the ignition switch is in the acc position. Elapsed time will increment when the ignition switch is in the on or start position. Display units of measure in to make your selection, press and release the function select but...

  • Page 177

    2. Press the menu button until personal settings (customer-programmable features) menu is reached. 3. Press the scroll button until “calibrate compass” is displayed in the evic. 4. Press and release the function select button to start the calibration. The “cal” indicator will be dis- played in the e...

  • Page 178

    1. Turn the ignition switch on. 2. Press the menu button until personal settings (customer-programmable features) menu is reached. 3. Press the scroll button until “compass variance” is displayed in the evic. 4. Press and release the function select button to change the variance number. Continue unt...

  • Page 179

    Auto unlock on exit when yes (y) is selected, all of the doors will unlock when the vehicle is stopped and the transmission is in the park or neutral position and the driver’s door is opened. To make your selection, press and release the function select button until yes (y) or no (n) appears. Remote...

  • Page 180

    When exiting the vehicle. To make your selection, press and release the function select button until “0,” “30,” “60,” or “90” appears. Auto high beams (available with smartbeam™ only) when this feature is selected, the high beam headlights will deactivate automatically under certain conditions. To m...

  • Page 181

    Vehicle. To make your selection, press and release the function select button until yes (y) or no (n) appears. Note: the seat will return to the memorized seat location (if recall memory with remote key unlock is set to on) when the rke transmitter is used to unlock the door. Refer to “easy entry/ex...

  • Page 182

    Display eco — if equipped the “eco” message is located in the compass/ temperature display, this message can be turned on or off. To make your selection, press and release the func- tion select button until “on” or “off” appears. System status press and release the menu button until one of the follo...

  • Page 183

    • your system can be set to display pressure units in psi, kpa, or bar. Sales code (rer/ren) — am/fm/cd/dvd radio – if equipped note: the sales code is located on the lower right side of the unit’s faceplate. The ren and rer radios contain a cd/dvd player, usb port, and a 30-gigabyte hard drive (hdd...

  • Page 184

    To manually set the clock — rer/ren 1. Turn on the radio. 2. Touch the screen where the time is displayed. 3. Touch the screen where “user clock” is displayed. The clock setting menu will appear on the screen. 4. To move the hour forward, touch the screen where the word “hour” with the arrow pointin...

  • Page 185

    2. Touch the screen where the time is displayed. The clock setting menu will appear on the screen. 3. When this feature is on, a check mark will appear in the box next to the words “show time if radio is off.” touch the screen where the words “show time if radio is off” are displayed to change the c...

  • Page 186

    Operating instructions — radio mode note: the ignition switch must be in the on or acc position to operate the radio. Power switch/volume control (rotary) push the on/volume control knob to turn on the radio. Push the on/volume control knob a second time to turn off the radio. Electronic volume cont...

  • Page 187

    4. Adjust the minutes using the right side tune/ scroll control knob. Press the tune/scroll control knob to save time change. 5. To exit, press any button/knob, or wait five seconds. Rw/ff pressing the rw (rewind) or ff (fast forward) buttons causes the tuner to search for the next frequency in the ...

  • Page 188

    Push the rotary tune/scroll control knob again to exit setting tone, balance, and fade. Am/fm button press the buttons to select either am or fm mode. Set/rnd button — to set the pushbutton memory when you are receiving a station that you wish to commit to pushbutton memory, press the set/rnd button...

  • Page 189

    Operation instructions — cd mode for cd and mp3 audio play note: • the ignition switch must be in the on or acc position to operate the radio. • this radio is capable of playing compact discs (cd), recordable compact discs (cd-r), rewritable compact discs (cd-rw), compact discs with mp3 tracks and m...

  • Page 190

    Eject button - ejecting a cd press the eject button to eject the cd. If you have ejected a disc and have not removed it within 10 seconds, it will be reloaded. If the cd is not removed, the radio will reinsert the cd but will not play it. A disc can be ejected with the radio and ignition off. Note: ...

  • Page 191

    Set/rnd button (random play button) press this button while the cd is playing to activate random play. This feature plays the selections on the compact disc in random order to provide an interesting change of pace. Press the right seek button to move to the next ran- domly selected track. Press the ...

  • Page 192

    • maximum number of characters in file/folder names: • level 1: 12 (including a separator ⬙.⬙ and a three- character extension) • level 2: 31 (including a separator ⬙.⬙ and a three- character extension) multisession disc formats are supported by the radio. Multisession discs may contain combinations...

  • Page 193

    Id3 tag information for artist, song title, and album title are supported for version 1 id3 tags. Id3 version 2 is not supported by the radios. Playlist files are not supported. Mp3 pro files are not supported. Playback of mp3 files when a medium containing mp3 data is loaded, the radio checks all f...

  • Page 194

    Note: the aux device must be turned on and the device’s volume set to proper level. If the aux audio is not loud enough, turn the device’s volume up. If the aux audio sounds distorted, turn the device’s volume down. Time button (auxiliary mode) press this button to change the display to time of day....

  • Page 195

    Power switch/volume control (rotary) push the on/volume control knob to turn on the radio. Push the on/volume control knob a second time to turn off the radio. Electronic volume control the electronic volume control turns continuously (360 degrees) in either direction without stopping. Turning the o...

  • Page 196

    If your vehicle is not equipped with or this feature is not available on your vehicle, a “not equipped with uconnect” message will display on the radio screen. Time button press the time button to alternate display of the time and radio frequency. Clock setting procedure 1. Press and hold the time b...

  • Page 197

    Tune control turn the rotary tune/scroll control knob clockwise to increase or counterclockwise to decrease the frequency. Setting the tone, balance, and fade push the rotary tune/scroll control knob and bass will display. Turn the tune/scroll control knob to the right or left to increase or decreas...

  • Page 198

    Toggle the music type button to select the following format types: program type 16-digit character display no program type or un- defined none adult hits adlt hit classical classicl classic rock cls rock college college country country foreign language language information inform jazz jazz news news...

  • Page 199

    By pressing the seek button when the music type icon is displayed, the radio will be tuned to the next frequency station with the same selected music type name. The music type function only operates when in the fm mode. If a preset button is activated while in the music type (program type) mode, the...

  • Page 200

    You may add a second station to each pushbutton by repeating the above procedure with this exception: press the set/rnd button twice and set 2 will show in the display window. Each button can be set for set 1 and set 2 in both am and fm. This allows a total of 12 am and 12 fm stations to be stored i...

  • Page 201

    If you insert a disc with the ignition on and the radio on, the unit will switch from radio to cd mode and begin to play when you insert the disc. The display will show the track number, and index time in minutes and seconds. Play will begin at the start of track 1. Caution! • this cd player will ac...

  • Page 202

    Time button press this button to change the display from a large cd playing time display to a small cd playing time display. Rw/ff press and hold ff (fast forward) and the cd player will begin to fast forward until ff is released or rw or another cd button is pressed. The rw (reverse) button works i...

  • Page 203

    The radio uses the following limits for file systems: • maximum number of folder levels: 8 • maximum number of files: 255 • maximum number of folders. (the radio display of file names and folder names is limited. For large numbers of files and/or folders, the radio may be unable to display the file ...

  • Page 204

    Mpeg specification sampling frequency (khz) bit rate (kbps) mpeg-1 audio layer 3 48, 44.1, 32 320, 256, 224, 192, 160, 128, 112, 96, 80, 64, 56, 48, 40, 32 mpeg-2 audio layer 3 24, 22.05, 16 160, 128, 144, 112, 96, 80, 64, 56, 48, 40, 32, 24, 16, 8 id3 tag information for artist, song title, and alb...

  • Page 205

    List button (cd mode for mp3 play) pressing the list button will bring up a list of all folders on the disc. Scrolling up or down the list is done by turning the tune/scroll control knob. Selecting a folder by pressing the tune/scroll control knob will begin playing the files contained in that folde...

  • Page 206

    Time button (auxiliary mode) press this button to change the display to time of day. The time of day will display for five seconds (when the ignition is off). Operating instructions - uconnect™ phone (if equipped) refer to “uconnect™ phone” in the uconnect™ user manual located on the dvd for further...

  • Page 207

    • connecting an ipod威 to the aux port located in the radio faceplate, plays media, but does not use the uci feature to control the connected device. Connecting the ipod 姞 use the provided connection cable to connect an ipod 威 to the vehicle’s 16–pin connector port (which is located in the glove comp...

  • Page 208

    Controlling the ipod 姞 using radio buttons to get into the uci (ipod 威) mode and access a connected ipod 威, press the “aux” button on the radio faceplate. Once in the uci (ipod 威) mode, ipod威 audio tracks (if available from ipod 威) start playing over the vehicle’s audio system. Play mode when switch...

  • Page 209

    Beginning of the track. If you press the seek >> button during play mode, it will jump to the next track in the list. • while a track is playing, press the info button to see the associated metadata (artist, track title, album, etc.) for that track. Pressing the info button again jumps to the next s...

  • Page 210

    • turning it clockwise (forward) and counterclock- wise (backward) scrolls through the lists, displaying the track detail on the radio display. Once you have the track to be played highlighted on the radio display, press the tune control knob to select and start playing the track. Turning the tune c...

  • Page 211

    • music type button: the music type button is another shortcut button to the genre listing on your ipod 威. Caution! • leaving the ipod威 (or any supported device) any- where in the vehicle in extreme heat or cold can alter the operation or damage the device. Follow the device manufacturer’s guideline...

  • Page 212

    Electronic serial number/sirius identification number (esn/sid) please have the following information available when calling: 1. The electronic serial number/sirius identification number (esn/sid). 2. Your vehicle identification number. To access the esn/sid, refer to the following steps: esn/sid ac...

  • Page 213

    Reception quality satellite reception may be interrupted due to one of the following reasons: • the vehicle is parked in an underground parking structure or under a physical obstacle. • dense tree coverage may interrupt reception in the form of short audio mutes. • driving under wide bridges or alon...

  • Page 214

    Rw/ff pressing the rw (rewind) or ff (fast forward) buttons causes the tuner to search for the next channel in the direction of the arrows. Tune control (rotary) turn the rotary tune/scroll control knob clockwise to increase or counterclockwise to decrease the channel. Music type button pressing thi...

  • Page 215

    Select the button (1-6) you wish to lock onto this channel and press and release that button. If a button is not selected within five seconds after pressing the set but- ton, the channel will continue to play but will not be stored into pushbutton memory. You may add a second channel to each pushbut...

  • Page 216

    Video entertainment system™ (sales code xrv) — if equipped the optional ves™ (video entertainment system) con- sists of a dvd player and lcd (liquid crystal display) screen, a battery-powered remote control, and two head- sets. Refer to the “uconnect™ studios” section of uconnect™ user manual locate...

  • Page 217

    Remote sound system controls — if equipped the remote sound system controls are located on the rear surface of the steering wheel. Reach behind the wheel to access the switches. The right-hand control is a rocker-type switch with a pushbutton in the center and controls the volume and mode of the sou...

  • Page 218

    Pressing the center button will make the radio switch between the various modes available (am/fm/tape/ cd, etc.). The left-hand control is a rocker-type switch with a pushbutton in the center. The function of the left-hand control is different depending on which mode you are in. The following descri...

  • Page 219

    Cd/dvd maintenance to keep a cd/dvd in good condition, take the following precautions: 1. Handle the disc by its edge; avoid touching the surface. 2. If the disc is stained, clean the surface with a soft cloth, wiping from center to edge. 3. Do not apply paper or tape to the disc; avoid scratch- ing...

  • Page 220

    Climate controls manual air conditioning and heating system — if equipped the controls for the heating/air conditioning and venti- lation system in this vehicle consist of a series of rotary knobs. These comfort controls can be set to obtain desired interior conditions. The instrument panel features...

  • Page 221

    Temperature control the temperature control rotary knob (in the center) controls the air tem- perature. The coldest temperature set- ting is on the extreme left and the warmest setting on the extreme right of the rotation. The knob can be posi- tioned at any point on the dial. Mode control the mode ...

  • Page 222

    Bi-level air flows both through the outlets located in the instrument panel and those located on the floor. Air flows through the registers in the back of the center console, and under the front seats to the rear seat passengers. These registers can be closed to partially block airflow. The center c...

  • Page 223

    Slight changes in engine speed or power may be noticed when the air conditioning compressor is on. This is a normal occurrence as the compressor will cycle on and off to maintain comfort and increase fuel economy. Automatic temperature control — if equipped the automatic temperature control system a...

  • Page 224

    Be used for front seat occupants only. The hi auto position should be used when more airflow is desired, or when rear seat occupants are present. Dial in the comfort setting you would like the system to maintain by rotating the driver’s or passenger’s control knob. Once the com- fort level is select...

  • Page 225

    Note: • the surface of the climate control panel, and the top center of the instrument panel should be kept free of debris due to the climate control sensor’s location. Mud on the windshield may also cause poor operation of this system. • to provide you with maximum comfort in the auto- matic mode, ...

  • Page 226

    226 understanding your instrument panel.

  • Page 227

    Note: regardless of the type of operation, when a temperature knob is set to the full clockwise or full counterclockwise position, the system will deliver full hot or full cold air out of the ducts, respectively. The operator can override the auto mode setting and select the direction of the air by ...

  • Page 228

    Bi-level air flows both through the outlets located in the instrument panel and those located on the floor. Air flows through the registers in the back of the center console, and under the front seats to the rear seat passengers. These registers can be closed to block airflow. The center console out...

  • Page 229

    Recirculation mode to be selected while in the defrost or defrost/floor modes. Attempting to use recirculation while in these modes will cause the led in the button to blink and then turn off. Operating tips window fogging windows will fog on the inside when the humidity inside the vehicle is high. ...

  • Page 230

    When using the air conditioner in extremely heavy traffic, in hot weather, especially when towing a trailer, additional engine cooling may be required. If this situa- tion is encountered, operate the transmission in a lower gear to increase engine rpm, coolant flow and fan speed. When stopped in hea...

  • Page 231

    Operating tips chart 4 understanding your instrument panel 231.

  • Page 233: Starting And Operating

    Starting and operating contents 䡵 starting procedure . . . . . . . . . . . . . . . . . . . . . 238 ▫ normal starting . . . . . . . . . . . . . . . . . . . . . 238 ▫ extreme cold weather (below ⫺20°f or ⫺29°c) . . . . . . . . . . . . . . . 239 ▫ if engine fails to start . . . . . . . . . . . . . . . ...

  • Page 234

    ▫ quadra-trac ii威 operating instructions/ precautions — if equipped . . . . . . . . . . . . . 251 ▫ shift positions . . . . . . . . . . . . . . . . . . . . . . 253 ▫ shifting procedures . . . . . . . . . . . . . . . . . . . 253 ▫ quadra-drive威 ii system — if equipped . . . . 256 䡵 on-road driving ti...

  • Page 235

    ▫ hill start assist (hsa) – four-wheel drive models with nv245 two–speed transfer case only . . . . . . . . . . . . . . . . . . . . . . . . . 275 ▫ hill descent control (hdc) – four-wheel drive models with nv245 two–speed transfer case only . . . . . . . . . . . . . . . . . . . 278 ▫ esp/bas warning...

  • Page 236

    䡵 fuel requirements . . . . . . . . . . . . . . . . . . . . . 309 ▫ 3.7 engine . . . . . . . . . . . . . . . . . . . . . . . . . 309 ▫ 5.7l engine . . . . . . . . . . . . . . . . . . . . . . . . 310 ▫ reformulated gasoline . . . . . . . . . . . . . . . . 310 ▫ gasoline/oxygenate blends . . . . . . ....

  • Page 237

    ▫ towing — quadra-trac i威 (single-speed transfer case) four-wheel drive models . . . 333 ▫ towing — quadra–trac ii威 /quadra–drive威 ii four-wheel drive models . . . . . . . . . . . . . 333 5 starting and operating 237.

  • Page 238

    Starting procedure before starting your vehicle, adjust your seat, adjust the inside and outside mirrors, fasten your seat belt, and if present, instruct all other occupants to buckle their seat belts. Warning! • never leave children alone in a vehicle. Leaving unattended children in a vehicle is da...

  • Page 239

    Extreme cold weather (below ⫺ 20°f or ⫺ 29°c) to ensure reliable starting at these temperatures, use of an externally powered electric engine block heater (avail- able from your authorized dealer) is recommended. If engine fails to start warning! • never pour fuel or other flammable liquids into the...

  • Page 240

    Release it as soon as the starter engages. The starter motor will disengage automatically in 10 seconds. Once this occurs, release the accelerator pedal, turn the ignition switch to the lock position, wait 10 to 15 seconds, then repeat the “normal starting” procedure. Caution! To prevent damage to t...

  • Page 241

    Automatic transmission caution! Damage to the transmission may occur if the follow- ing precautions are not observed: • shift into park only after the vehicle has come to a complete stop. • shift into or out of reverse only after the vehicle has come to a complete stop and the engine is at idle spee...

  • Page 242

    Brake/transmission shift interlock system this vehicle is equipped with a brake transmission shift interlock system (btsi) that holds the shift lever in the park position when the ignition switch is in the lock position. To move the shift lever out of the park position, the ignition switch must be t...

  • Page 243

    6. Move the shift lever into the neutral position. 7. The vehicle may then be started in neutral. Have your vehicle inspected by your local authorized dealer if the shift lock manual override has been used. Five–speed automatic transmission the electronically-controlled transmission provides a preci...

  • Page 244

    Warning! (continued) • it is dangerous to move the shift lever out of park or neutral if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in reverse. You could lose control of the vehicle and hit someone or som...

  • Page 245

    Note: • if you pull and hold (not tap) the shift lever to the left (-), the transmission will downshift to the lowest gear that can be attained without overrevving the engine. The display will show the gear the vehicle is in and will limit the top gear to the one displayed. • if you pull and hold (n...

  • Page 246

    Warning! Do not downshift for additional engine braking on a slippery surface. The drive wheels could lose their grip and the vehicle could skid. Screen display 1 2 3 4 5* d actual gear(s) allowed 1 1-2 1-3 1-4 1-5 1-5 * applies to vehicles equipped with 5.7l engines only. Note: to select the proper...

  • Page 247

    Note: if the vehicle is started in extremely cold tem- peratures, the transmission may not shift into overdrive and will automatically select the most desirable gear for operation at this temperature. Normal operation will resume when the transmission fluid temperature has risen to a suitable level....

  • Page 248

    When to use tow/haul mode — if equipped when driving in hilly areas, towing a trailer, carrying a heavy load, etc., and frequent transmission shifting oc- curs, press the tow/haul switch. This will improve performance and reduce the potential for transmission overheating or failure due to excessive ...

  • Page 249

    Transmission limp home mode transmission function is monitored for abnormal condi- tions. If a condition is detected that could result in transmission damage, the transmission limp home mode will be engaged. In this mode, the transmission will remain in the current gear (3.7l engine) or in direct ge...

  • Page 250

    Note: • the torque converter clutch will not engage until the transmission fluid and engine coolant are warm [usu- ally after 1 to 3 miles (1.6 to 4.8 km) of driving]. Because the engine speed is higher when the torque converter clutch is not engaged, it may seem as if the transmission is not shifti...

  • Page 251

    The vehicle, may lead to transmission overheating and failure. Allow the engine to idle with the shift lever in neutral for at least one minute after every five rocking-motion cycles. This will minimize overheating and reduce the risk of transmission failure during pro- longed efforts to free a stuc...

  • Page 252

    This transfer case is fully automatic in the 4wd hi mode. When additional traction is required, the 4wd low position can be used to lock the front and rear driveshafts together and force the front and rear wheels to rotate at the same speed. The 4wd low position is intended for loose, slippery road ...

  • Page 253

    Shift positions for additional information on the appropriate use of each transfer case mode position, see the information below: 4wd hi this range is used on surfaces such as ice, snow, gravel, sand, and dry hard pavement. Neutral this range disengages both the front and rear driveshafts from the p...

  • Page 254

    Note: if shift conditions/interlocks are not met, or a transfer case motor temperature protection condition exists, a “check shift procedures” message will flash from the electronic vehicle information center (evic). Refer to “electronic vehicle information center (evic)” in section 4 of this manual...

  • Page 255

    Clutch teeth alignment and shift completion to occur. The preferred method is with the vehicle rolling 0 to 3 mph (0 to 5 km/h). If the vehicle is moving faster than 3 mph (5 km/h), the transfer case will not allow the shift. Neutral shift procedure 1. Key on, engine off. 2. Vehicle stopped, with fo...

  • Page 256

    Quadra-drive 姞 ii system — if equipped the optional quadra-drive 威 ii system features three torque transfer couplings. The couplings include elec- tronic limited-slip differential (elsd) front and rear axles and quadra-trac ii 威 transfer case. The optional elsd axles are fully automatic and require ...

  • Page 257

    Off-road driving tips note: prior to off-road driving, remove the front air dam to prevent damage. The front air dam is attached to the lower front fascia with quarter turn fasteners and can be removed by hand. When to use 4wd low range — if equipped when off-road driving, shift to 4wd low for addit...

  • Page 258

    Flowing water if the water is swift flowing and rising (as in storm run-off), avoid crossing until the water level recedes and/or the flow rate is reduced. If you must cross flowing water avoid depths in excess of 9 in (23 cm). The flowing water can erode the streambed, causing your vehicle to sink ...

  • Page 259

    Hill climbing note: before attempting to climb a hill, determine the conditions at the crest and/or on the other side. Before climbing a steep hill, shift the transmission to a lower gear and shift the transfer case to 4wd low. Use first gear and 4wd low for very steep hills. If you stall or begin t...

  • Page 260

    Traction downhill shift the transmission into a low gear, and the transfer case into 4wd low range. Let the vehicle go slowly down the hill with all four wheels turning against engine compression drag. This will permit you to control the vehicle speed and direction. When descending mountains or hill...

  • Page 261

    Warning! Abrasive material in any part of the brakes may cause excessive wear or unpredictable braking. You might not have full braking power when you need it to prevent an accident. If you have been operating your vehicle in dirty conditions, get your brakes checked and cleaned as necessary. • if y...

  • Page 262

    Warning! Continued operation with reduced power steering assist could pose a safety risk to yourself and others. Service should be obtained as soon as possible. Caution! Prolonged operation of the steering system at the end of the steering wheel travel will increase the steering fluid temperature an...

  • Page 263

    Warning! Fluid level should be checked on a level surface and with the engine off to prevent injury from moving parts and to ensure accurate fluid level reading. Do not overfill. Use only manufacturers recommended power steering fluid. If necessary, add fluid to restore to the proper indicated level...

  • Page 264

    The shift lever in park, otherwise the load on the transmission locking mechanism may make it difficult to move the shift lever out of park. Warning! • always fully apply the parking brake when leav- ing your vehicle, or it may roll and cause damage or injury. Also, be certain to leave the transmiss...

  • Page 265

    Wheel lock-up and help avoid skidding on slippery surfaces. All vehicle wheels and tires must be the same size and type, and tires must be properly inflated, to produce accurate signals for the computer. Warning! Significant over or under-inflation of tires or mixing sizes of tires or wheels on the ...

  • Page 266

    Warning! (continued) • the abs cannot prevent accidents, including those resulting from excessive speed in turns, following another vehicle too closely, or hydro- planing. Only a safe, attentive, and skillful driver can prevent accidents. • the capabilities of an abs equipped vehicle must never be e...

  • Page 267

    • do not drive too fast for road conditions, especially when roads are wet or slushy. A wedge of water can build up between the tire tread and the road. This hydroplaning action can cause loss of traction, braking ability, and control. • after going through deep water or a car wash, brakes may becom...

  • Page 268

    Warning! The abs cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions. The abs cannot prevent accidents, including those re- sulting from excessive speed in turns, driving on very slippery surfaces, or hydropla...

  • Page 269

    Benefit of the system, you must apply continuous brak- ing pressure during the stopping sequence (do not “pump” the brakes). Do not reduce brake pedal pressure unless braking is no longer desired. Once the brake pedal is released, the bas is deactivated. Warning! The bas cannot prevent the natural l...

  • Page 270

    Note: anytime the esp system is in the “full off” mode, erm is disabled. Refer to “electronic stability program (esp)” for a complete explanation of the avail- able esp modes. Warning! Many factors, such as vehicle loading, road condi- tions and driving conditions, influence the chance that wheel li...

  • Page 271

    • understeer - when the vehicle is turning less than appropriate for the steering wheel position. The “esp/tcs indicator light” located in the instrument cluster will start to flash as soon as the tires lose traction and the esp system becomes active. The “esp/tcs indicator light” also flashes when ...

  • Page 272

    High range (four-wheel drive models) or two-wheel drive models on this is the normal operating mode for esp in 4wd high range and in two-wheel drive vehicles. Whenever the vehicle is started or the transfer case (if equipped) is shifted from 4wd low range or neutral back to 4wd high range, the esp s...

  • Page 273

    Note: to improve the vehicle’s traction when driving with snow chains, or starting off in deep snow, sand, or gravel, it may be desirable to switch to the “partial off” mode by pressing the “esp off” switch. Once the situation requiring esp to be switched to the “partial off” mode is overcome, turn ...

  • Page 274

    Warning! With the esp switched off, the enhanced vehicle stability offered by esp and erm are unavailable. In an emergency evasive maneuver, the esp and erm systems will not engage to assist in maintaining stability. The “full off” esp mode is intended for off-road use only. 4wd low range full off t...

  • Page 275

    Warning! With the esp switched off, the enhanced vehicle stability offered by esp and erm are unavailable. In an emergency evasive maneuver, the esp and erm systems will not engage to assist in maintaining stability. The “full off” mode is intended for off- road use only. Trailer sway control (tsc) ...

  • Page 276

    Period of time after the driver takes their foot off of the brake pedal. If the driver does not apply the throttle during this short period of time, the system will release brake pressure and the vehicle will roll down the hill. The system will release brake pressure in proportion to the amount of t...

  • Page 277

    Warning! • if you use a trailer brake controller with your trailer, your trailer brakes may be activated and deactivated with the brake switch. If so, when the brake pedal is released, there may not be enough brake pressure to hold the vehicle and trailer on a hill and this could cause a collision w...

  • Page 278

    Hill descent control (hdc) – four-wheel drive models with nv245 two–speed transfer case only hdc maintains vehicle speed while descending hills during off-road driving situations and is available in 4wd low range only. To enable hdc (transfer case must be in 4wd low range), press the hdc switch. If ...

  • Page 279

    The hdc speed may be adjusted by the driver to suit the driving conditions. The speed corresponds to the trans- mission gear selected. • 1st = 1 mph (1.6 km/h) • 2nd = 2.5 mph (4 km/h) • 3rd = 4 mph (6 km/h) • 4th = 5.5 mph (9 km/h) • 5th = 7.5 mph (12 km/h) • reverse = 1 mph (1.6 km/h) • neutral = ...

  • Page 280

    Esp/bas warning light and esp/tcs indicator light the malfunction indicator light for the esp is combined with the bas indicator. The “esp/ bas warning light” and the “esp/tcs indi- cator light” in the instrument cluster both come on when the ignition switch is turned to the on position. They should...

  • Page 281

    Tire safety information tire markings note: • p (passenger) - metric tire sizing is based on u.S. Design standards. P-metric tires have the letter “p” molded into the sidewall preceding the size designa- tion. Example: p215/65r15 95h. • european-metric tire sizing is based on european design standar...

  • Page 282

    • temporary spare tires are high-pressure compact spares designed for temporary emergency use only. Tires designed to this standard have the letter “t” molded into the sidewall preceding the size designa- tion. Example: t145/80d18 103m. • high flotation tire sizing is based on u.S. Design standards ...

  • Page 283

    Tire sizing chart example: size designation: p = passenger car tire size based on u.S. Design standards ⴖ....Blank....ⴖ = passenger car tire based on european design standards lt = light truck tire based on u.S. Design standards t = temporary spare tire 31 = overall diameter in inches (in) 215 = sec...

  • Page 284

    Example: service description: 95 = load index — a numerical code associated with the maximum load a tire can carry h = speed symbol — a symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions — the maximum speed corres...

  • Page 285

    Tire identification number (tin) the tin may be found on one or both sides of the tire, however, the date code may only be on one side. Tires with white sidewalls will have the full tin, including the date code, located on the white sidewall side of the tire. Look for the tin on the outboard side of...

  • Page 286

    Tire loading and tire pressure tire placard location note: the proper cold tire inflation pressure is listed on the driver’s side b-pillar. Tire and loading information placard this placard tells you important information about the: 1) number of people that can be carried in the vehicle 2) total wei...

  • Page 287

    Note: under a maximum loaded vehicle condition, gross axle weight ratings (gawrs) for the front and rear axles must not be exceeded. For further information on gawrs, vehicle loading, and trailer towing, refer to “vehicle loading” in this section. To determine the maximum loading conditions of your ...

  • Page 288

    Note: • the following table shows examples on how to calcu- late total load, cargo/luggage, and towing capacities of your vehicle with varying seating configurations and number and size of occupants. This table is for illustration purposes only and may not be accurate for the seating and load carry ...

  • Page 289

    5 starting and operating 289.

  • Page 290

    Warning! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. Tires — general information tire pressure proper tire inflation pressur...

  • Page 291

    Warning! (continued) • unequal tire pressures from one side of the ve- hicle to the other can cause the vehicle to drift to the right or left. • always drive with each tire inflated to the recom- mended cold tire inflation pressure. Economy improper inflation pressures can cause uneven wear patterns...

  • Page 292

    Caution! After inspecting or adjusting the tire pressure, al- ways reinstall the valve stem cap (if equipped). This will prevent moisture and dirt from entering the valve stem, which could damage it. Inflation pressures specified on the placard are always cold tire inflation pressure. Cold tire infl...

  • Page 293

    Loading may be required for high-speed vehicle opera- tion. Refer to original equipment or an authorized tire dealer for recommended safe operating speeds, loading and cold tire inflation pressures. Warning! High speed driving with your vehicle at or above maximum load is dangerous. The added strain...

  • Page 294

    Warning! Temporary use spare tires are for emergency use only. With these tires, do not drive more than 50 mph (80 km/h). Temporary use spare tires have limited tread life. When the tread is worn to the tread wear indicators, the temporary use spare tire needs to be replaced. Be sure to follow the w...

  • Page 295

    Warning! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause tire dam- age or failure. A tire could explode and injure some- one. Do not spin your vehicle’s wheels faster than 35 mph (55 km/h) when you are stuck, and do not let anyone near a spinning wheel no...

  • Page 296

    Life of tire the service life of a tire is dependent upon various factors including but not limited to: • driving style • tire pressure • distance driven warning! Tires and the spare tire should be replaced after six years, regardless of the remaining tread. Failure to follow this warning can result...

  • Page 297

    Warning! • do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change sus- pension dimensions and performance characteris- tics, resulting in changes to steering, handling, and braking of your vehicle. This can caus...

  • Page 298

    Tire chains certain models have sufficient tire-to-body clearance to allow use of tire chains. Install chains on rear tires only. Follow these recommendations to guard against damage and excessive tire and chain wear: • do not install tire chains or traction devices on ve- hicles with larger than p2...

  • Page 299

    The suggested rotation method is the “forward-cross” shown in the following diagram. Tire pressure monitor system (tpms) the tire pressure monitoring system (tpms) will warn the driver of a low tire pressure based on the vehicle recommended cold tire pressure. The tire pressure will vary with temper...

  • Page 300

    The tpms will continue to warn the driver of low tire pressure as long as the condition exists, and will not turn off until the tire pressure is at or above recommended cold tire pressure. Once the low tire pressure warning has been illuminated, the tire pressure must be increased to the recommended...

  • Page 301

    Caution! • the tpms has been optimized for the original equipment tires and wheels. Tpms pressures have been established for the tire size equipped on your vehicle. Undesirable system operation or sensor damage may result when using replacement equipment that is not of the same size, type, and/or st...

  • Page 302

    • seasonal temperature changes will affect tire pressure, and the tpms will monitor the actual tire pressure in the tire. Base system the tire pressure monitor system (tpms) uses wireless technology with wheel rim-mounted electronic sensors to monitor tire pressure levels. Sensors, mounted to each w...

  • Page 303

    Pressures have been received. The vehicle may need to be driven for up to 20 minutes above 15 mph (24 km/h) to receive this information. The tire pressure monitoring telltale light will flash on and off for 75 seconds, and remain on solid when a system fault is detected. In addition, a “check tpm sy...

  • Page 304

    • if your vehicle is not equipped with a matching full-size spare wheel and tire assembly, it does not have a tire pressure monitoring sensor in the spare tire. The tpms will not be able to monitor the tire pressure. If you install the spare tire, in place of a road tire, that has a pressure below t...

  • Page 305

    The tire pressure monitor system (tpms) consists of the following components: • receiver module • four tire pressure monitoring sensors • three trigger modules (mounted in three of the four wheel wells) • various tire pressure monitoring system messages, which display in the electronic vehicle infor...

  • Page 306

    Note: your system can be set to display pressure units in psi, kpa, or bar. Should a low tire condition occur on any of the four active road tire(s), you should stop as soon as possible, and inflate the low tire(s) that is “flashing” on the graphic display to the vehicle’s recommended cold tire pres...

  • Page 307

    If the ignition key is cycled, this sequence will repeat, providing the system fault still exists. If the system fault no longer exists, the tire pressure monitoring telltale light will no longer flash, the ⬙check tpm system⬙ message will not be present, and a pressure value will be displayed instea...

  • Page 308

    Note: • if your vehicle is equipped with a matching full-size spare wheel and tire assembly, it has a tire pressure monitoring sensor, and can be monitored by the tire pressure monitoring system (tpms). In the event that the matching full-size spare tire is swapped with a low pressure road tire, the...

  • Page 309

    The evic will display a ⬙check tpm system⬙ message for three seconds and then display dashes (- -) in place of the pressure value. Once you repair or replace the original road tire, and reinstall it on the vehicle in place of the spare tire, the tpms will update automatically. In addition, the tire ...

  • Page 310

    5.7l engine the 5.7l engine is designed to meet all emissions regulations and provide satisfac- tory fuel economy and performance when using high-quality unleaded gasoline hav- ing an octane range of 87 to 89. The manu- facturer recommends the use of 89 octane for optimum performance. The use of pre...

  • Page 311

    Gasoline/oxygenate blends some fuel suppliers blend unleaded gasoline with oxy- genates such as 10% ethanol, mtbe, and etbe. Oxygen- ates are required in some areas of the country during the winter months to reduce carbon monoxide emissions. Fuels blended with these oxygenates may be used in your ve...

  • Page 312

    • disconnect and reconnect the battery to reset the engine controller memory more extensive repairs will be required for prolonged exposure to e-85 fuel. Mmt in gasoline mmt is a manganese containing metallic additive that is blended into some gasoline to increase octane. Gasoline blended with mmt p...

  • Page 313

    Fuel system cautions caution! Follow these guidelines to maintain your vehicle’s performance: • the use of leaded gas is prohibited by federal law. Using leaded gasoline can impair engine performance and damage the emission control system. • an out-of-tune engine, or certain fuel or ignition malfunc...

  • Page 314

    • do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas which can kill. Never run the engine in a closed area, such as a garage, and never sit in a parked vehicle with the engine running for an extended period. If the vehicle is stopped in an open area with the engi...

  • Page 315

    Caution! • damage to the fuel system or emission control system could result from using an improper fuel cap (gas cap). A poorly fitting cap could let impu- rities into the fuel system. Also, a poorly fitting aftermarket cap can cause the malfunction indica- tor light (mil) to illuminate, due to fue...

  • Page 316

    Warning! A fire may result if gasoline is pumped into a portable container that is inside of a vehicle. You could be burned. Always place gas containers on the ground while filling. Loose fuel filler cap message if the vehicle diagnostic system determines that the fuel filler cap is loose, improperl...

  • Page 317

    Included on this label and indicates the month, day, and hour of manufacture. The bar code that appears on the bottom of the label is your vin. Gross vehicle weight rating (gvwr) the gvwr is the total permissible weight of your vehicle including driver, passengers, vehicle, options, trailer tongue w...

  • Page 318

    Curb weight the curb weight of a vehicle is defined as the total weight of the vehicle with all fluids, including vehicle fuel, at full capacity conditions, and with no occupants or cargo loaded into the vehicle. The front and rear curb weight values are determined by weighing your vehicle on a comm...

  • Page 319

    Trailer towing in this section you will find safety tips and information on limits to the type of towing you can reasonably do with your vehicle. Before towing a trailer, carefully review this information to tow your load as efficiently and safely as possible. To maintain warranty coverage, follow t...

  • Page 320

    Warning! It is important that you do not exceed the maximum front or rear gawr. A dangerous driving condition can result if either rating is exceeded. You could lose control of the vehicle and have an accident. Trailer tongue weight (tw) the tw is the downward force exerted on the hitch ball by the ...

  • Page 321

    Depending on vehicle and trailer configuration/loading to comply with gross axle weight rating (gawr) requirements. Warning! • an improperly adjusted weight-distributing hitch system may reduce handling, stability, and brak- ing performance, and could result in an accident. • weight-distributing hit...

  • Page 322

    With weight-distributing hitch (correct) improper adjustment of weight-distributing hitch (incorrect) 322 starting and operating.

  • Page 323

    Trailer hitch classification your vehicle may be factory equipped for safe towing of trailers weighing over 3,500 lbs (1 587 kg) with the optional trailer tow prep package. See your authorized dealer for package content. The following chart provides the industry standard for the maximum trailer weig...

  • Page 324

    Trailer towing weights (maximum trailer weight ratings) the following chart provides the maximum trailer weight ratings towable for your given drivetrain. Engine/model model gcwr (gross com- bined wt. Rating) frontal area max. Gtw (gross trailer wt.) max. Trailer tongue wt. (see note) 3.7l 4x2 8,400...

  • Page 325

    Trailer and trailer tongue weight always load a trailer with 60% to 65% of the weight in the front of the trailer. This places 10% to 15% of the gross trailer weight (gtw) on the tow hitch of your vehicle. Loads balanced over the wheels, or heavier in the rear, can cause the trailer to sway severely...

  • Page 326

    Note: remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options, or authorized dealer-installed options, must be considered as part of the total load on your vehicle. Refer to the tire and loading information placard in the “tire...

  • Page 327

    Warning! (continued) • improper towing can lead to an injury accident. Follow these guidelines to make your trailer tow- ing as safe as possible: • when hauling cargo or towing a trailer, do not over- load your vehicle or trailer. Overloading can cause a loss of control, poor performance or damage t...

  • Page 328

    Towing requirements — tires − do not attempt to tow a trailer while using a compact spare tire. − proper tire inflation pressures are essential to the safe and satisfactory operation of your vehicle. Refer to “tires – general information” for proper tire inflation procedures. − check the trailer tir...

  • Page 329

    Caution! If the trailer weighs more than 1,000 lbs (454 kg) loaded, it should have its own brakes and they should be of adequate capacity. Failure to do this could lead to accelerated brake lining wear, higher brake pedal effort, and longer stopping distances. Warning! • do not connect trailer brake...

  • Page 330

    The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector. Refer to the following illustrations. Four-pin connector 1 — female pins 4 — park 2 — male pin 5 — left stop/turn 3 — ground 6 — right stop/turn seven-pin connector 1 — battery 5 — ground...

  • Page 331

    Towing tips before setting out on a trip, practice turning, stopping and backing the trailer in an area away from heavy traffic. Automatic transmission the drive range can be selected when towing. How- ever, if frequent shifting occurs while in this range, the tow/haul mode (if equipped), or a lower...

  • Page 332

    Cooling system to reduce potential for engine and transmission over- heating, take the following actions: − city driving when stopped for short periods of time, shift the trans- mission into neutral and increase engine idle speed. − highway driving reduce speed. − air conditioning turn off temporari...

  • Page 333

    Towing — quadra-trac i 姞 (single-speed transfer case) four-wheel drive models recreational towing is not allowed. This model does not have a neutral position in the transfer case. Towing — quadra–trac ii 姞 /quadra–drive 姞 ii four-wheel drive models caution! Front or rear wheel lifts should not be us...

  • Page 334

    Hold down the neutral “pin” switch (with a pen, etc.) for four seconds until the led lamp by the switch starts to blink, indicating shift in progress. The lamp will stop blinking (stay on solid) when the neutral shift is complete. A “4wd system in neutral” message will display on the evic (electroni...

  • Page 335

    9. Shift the transmission into park. 10. Place the ignition key in the off position, and remove key. 11. Apply the parking brake. 12. Attach the vehicle to the tow vehicle with tow bar. 13. Release the parking brake. Caution! Transmission damage may occur if the transmission is shifted into park wit...

  • Page 336

    Hold down the neutral “pin” switch (with a pen, etc.) for four seconds until the led lamp by the switch starts to blink, indicating shift in progress. The lamp will stop blinking (go out) when shift is complete. The “4wd system in neutral” message will no longer be displayed on the evic (electronic ...

  • Page 337

    Note: when shifting out of transfer case neutral, turning the engine off may be required to avoid gear clash. Warning! You or others could be injured if you leave the vehicle unattended with the transfer case in the neutral position without first fully engaging the parking brake. The transfer case n...

  • Page 339: Contents

    What to do in emergencies contents 䡵 hazard warning flashers . . . . . . . . . . . . . . . . 340 䡵 if your engine overheats . . . . . . . . . . . . . . . . 340 䡵 jacking and tire changing . . . . . . . . . . . . . . . 341 ▫ jack location . . . . . . . . . . . . . . . . . . . . . . . 342 ▫ spare tire...

  • Page 340

    Hazard warning flashers the hazard warning flasher switch is located on the switch bank just above the climate controls. Press the switch to turn on the hazard warning flasher. When the switch is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency. ...

  • Page 341

    Note: there are steps that you can take to slow down an impending overheat condition: • if your air conditioner (a/c) is on, turn it off. The a/c system adds heat to the engine cooling system and turning the a/c off can help remove this heat. • you can also turn the temperature control to maxi- mum ...

  • Page 342

    Jack location the scissor-type jack and tire changing tools are located in the passenger side compartment, behind the second row seat. Spare tire stowage the spare tire is stowed under the rear of the vehicle by means of a cable winch mechanism. To remove or stow the spare, use the jack handle to ro...

  • Page 343

    Spare tire removal fit the jack handle extension over the drive nut. Use the lug wrench to rotate the nut counterclockwise until the spare is on the ground with enough slack in the cable to allow you to pull the tire out from under the vehicle. Caution! • the winch mechanism is designed for use with...

  • Page 344

    Warning! Do not attempt to change a tire on the side of the vehicle closest to moving traffic. Pull far enough off the road to avoid being hit when operating the jack or changing the wheel. 2. Set the parking brake. 3. Place the shift lever into park. 4. Turn the ignition off. 5. Turn on the hazard ...

  • Page 345

    Warning! (continued) • never start or run the engine with the vehicle on a jack. • do not let anyone sit in the vehicle when it is on a jack. • do not get under the vehicle when it is on a jack. • only use the jack in the positions indicated and for lifting this vehicle during a tire change. • if wo...

  • Page 346

    3. Assemble the jack and jacking tools as shown. Connect jack handle driver (1) to two extensions (2) then to the lug wrench (3). 4. Locate the jack as shown. For the front axle, place it under the front lower control arm. Do not raise the vehicle until you are sure the jack is fully engaged. For th...

  • Page 347

    Wheel when jacking on the rear axle. Do not raise the vehicle until you are sure the jack is fully engaged. 5. Raise the vehicle by turning the jack screw clockwise. Raise the vehicle only until the tire just clears the surface and enough clearance is obtained to install the spare tire. Minimum tire...

  • Page 348

    Wheel nut tightness is 95 ft lbs (130 n·m). If in doubt about the correct tightness, have them checked with a torque wrench by your authorized dealer or at a service station. 10. Lower the jack to its fully closed position. Warning! A loose tire or jack, thrown forward in a collision or hard stop co...

  • Page 349

    Warning! • remove any metal jewelry such as watch bands or bracelets that might make an inadvertent electrical contact. You could be seriously injured. • battery fluid is a corrosive acid solution that can cause serious burns; do not allow battery fluid to contact eyes, skin or clothing. Wear safety...

  • Page 350

    4. Connect one end of a jumper cable to the positive terminal of the booster battery. Connect the other end of the same cable to the positive terminal of the discharged battery. Warning! • do not permit vehicles to touch each other as this could establish a ground connection and personal injury coul...

  • Page 351

    Warning! Any procedure other than above could result in: • personal injury caused by electrolyte squirting out the battery vent. • personal injury or property damage due to battery explosion. Caution! Any procedure other than above could result in damage to the charging system of the booster vehicle...

  • Page 352

    Towing a disabled vehicle 2–wheel drive models only provided the transmission is operable, tow only in neu- tral at speeds not exceeding 30 mph (48 km/h), for distances of not more than 15 miles (24 km). Caution! Towing at more than 30 mph (48 km/h) or for more than 15 miles (24 km), can cause sever...

  • Page 353: Maintaining Your Vehicle

    Maintaining your vehicle contents 䡵 engine compartment – 3.7l . . . . . . . . . . . . . . 356 䡵 engine compartment – 5.7l . . . . . . . . . . . . . . 357 䡵 onboard diagnostic system – obd ii . . . . . . . 358 ▫ loose fuel filler cap message . . . . . . . . . . . 358 䡵 emissions inspection and mainte...

  • Page 354

    ▫ cooling system . . . . . . . . . . . . . . . . . . . . . 373 ▫ brake system . . . . . . . . . . . . . . . . . . . . . . . 378 ▫ front/rear axle fluid . . . . . . . . . . . . . . . . . 380 ▫ transfer case . . . . . . . . . . . . . . . . . . . . . . . 381 ▫ automatic transmission . . . . . . . . . ....

  • Page 355

    䡵 fluids, lubricants, and genuine parts . . . . . . . 406 ▫ engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . 406 ▫ chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . 407 7 maintaining your vehicle 355.

  • Page 356

    Engine compartment – 3.7l 1 — engine coolant reservoir 6 — washer fluid reservoir 2 — engine oil dipstick 7 — battery 3 — brake fluid reservoir 8 — engine oil fill 4 — power distribution center 9 — coolant pressure cap 5 — integrated power module 10 — air cleaner filter 356 maintaining your vehicle.

  • Page 357

    Engine compartment – 5.7l 1 — engine coolant reservoir 7 — washer fluid reservoir 2 — automatic transmission dipstick 8 — battery 3 — engine oil fill 9 — engine oil dipstick 4 — brake fluid reservoir 10 — coolant pressure cap 5 — power distribution center 11 — air cleaner filter 6 — integrated power...

  • Page 358

    Onboard diagnostic system – obd ii your vehicle is equipped with a sophisticated onboard diagnostic system called obd ii. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide ex...

  • Page 359

    The message will remain displayed until the vehicle diagnostic system can retest the fuel system. The test will perform the next time the vehicle is started, if the vehicle was keyed off above 40°f (4°c) outside temperature and the following vehicle start is above 40°f (4°c) outside temperature. It ...

  • Page 360

    2. Turn the ignition to the on position, but do not crank or start the engine. 3. If you crank or start the engine, you will have to start this test over. 4. As soon as you turn your key to the on position, you will see the mil symbol come on as part of a normal bulb check. 5. Approximately 15 secon...

  • Page 361

    Replacement parts use of genuine mopar 威 parts for normal/scheduled maintenance and repairs is highly recommended to en- sure the designed performance. Damage or failures caused by the use of non-mopar 威 parts for maintenance and repairs will not be covered by the manufacturer’s warranty. Dealer ser...

  • Page 362

    Caution! • failure to properly maintain your vehicle or per- form repairs and service when necessary could result in more costly repairs, damage to other components or negatively impact vehicle perfor- mance. Immediately have potential malfunctions examined by an authorized chrysler group llc dealer...

  • Page 363

    Caution! Overfilling or underfilling the crankcase will cause aeration or loss of oil pressure. This could damage your engine. Change engine oil the oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance. Refer to the “maintenance schedule” in s...

  • Page 364

    Engine oil viscosity (3.7l and 5.7l engines) sae 5w-20 engine oil is recommended for all operating temperatures. This engine oil improves low temperature starting and vehicle fuel economy. The engine oil filler cap also shows the recommended engine oil viscosity for your vehicle. For information on ...

  • Page 365

    Engine oil filter the engine oil filter should be replaced with a new filter at every oil change. Engine oil filter selection the manufacturer’s engines have a full-flow type dispos- able oil filter. Use a filter of this type for replacement. The quality of replacement filters varies considerably. O...

  • Page 366

    Maintenance-free battery your vehicle is equipped with a maintenance-free battery. You will never have to add water, nor is periodic main- tenance required. Warning! • battery fluid is a corrosive acid solution and can burn or even blind you. Do not allow battery fluid to contact your eyes, skin or ...

  • Page 367

    Air conditioner maintenance for best possible performance, your air conditioner should be checked and serviced by an authorized dealer at the start of each warm season. This service should include cleaning of the condenser fins and a performance test. Drive belt condition should also be checked at t...

  • Page 368

    Note: use only manufacturer approved a/c system sealers, stop leak products, seal conditioners, compres- sor oil, and refrigerants. Refrigerant recovery and recycling r-134a air conditioning refrigerant is a hydrofluoro- carbon (hfc) that is endorsed by the environmental protection agency (epa) and ...

  • Page 369

    Operation of the wipers on dry glass for long periods may cause deterioration of the wiper blades. Always use washer fluid when using the wipers to remove salt or dirt from a dry windshield. Avoid using the wiper blades to wipe frost or ice from the windshield. Keep the blade rubber out of contact w...

  • Page 370

    Warning! Commercially available windshield washer solvents are flammable. They could ignite and burn you. Care must be exercised when filling or working around the washer solution. Exhaust system the best protection against carbon monoxide entry into the vehicle body is a properly maintained engine ...

  • Page 371

    Caution! The catalytic converter requires the use of unleaded fuel only. Leaded gasoline will destroy the effective- ness of the catalyst as an emissions control device and may seriously reduce engine performance and cause serious damage to the engine. Under normal operating conditions, the catalyti...

  • Page 372

    Warning! A hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your exhaust system. Do not park or operate your vehicle in areas where your exhaust system can contact anything that can burn. In unusual situati...

  • Page 373

    Cooling system warning! You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator. If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool. Never try to open a cooling system pressure cap when the radiat...

  • Page 374

    Cooling system — drain, flush, and refill if the engine coolant (antifreeze) is dirty and contains a considerable amount of sediment, clean and flush with reliable cooling system cleaner. Follow with a thorough rinsing to remove all deposits and chemicals. Properly dispose of the old engine coolant ...

  • Page 375

    Caution! (continued) • this vehicle has not been designed for use with propylene glycol-based engine coolant (anti- freeze). Use of propylene glycol-based engine coolant (antifreeze) is not recommended. Adding coolant your vehicle has been built with an improved engine coolant (antifreeze) that allo...

  • Page 376

    Please note that it is the owner’s responsibility to main- tain the proper level of protection against freezing ac- cording to the temperatures occurring in the area where the vehicle is operated. Note: mixing engine coolant (antifreeze) types will decrease the life of the engine coolant (antifreeze...

  • Page 377

    Disposal of used engine coolant used ethylene glycol-based engine coolant (antifreeze) is a regulated substance requiring proper disposal. Check with your local authorities to determine the disposal rules for your community. To prevent ingestion by ani- mals and children, do not store ethylene glyco...

  • Page 378

    If an examination of your engine compartment shows no evidence of radiator or hose leaks, the vehicle may be safely driven. The vapor will soon dissipate. • do not overfill the coolant recovery bottle. • check engine coolant (antifreeze) freeze point in the radiator and in the coolant recovery bottl...

  • Page 379

    Warning! Riding the brakes can lead to brake failure and possibly an accident. Driving with your foot resting or riding on the brake pedal can result in abnormally high brake temperatures, excessive lining wear, and possible brake damage. You would not have your full braking capacity in an emergency...

  • Page 380

    Warning! (continued) • to avoid contamination from foreign matter or moisture, use only new brake fluid or fluid that has been in a tightly closed container. Keep the master cylinder reservoir cap secured at all times. Brake fluid in a open container absorbs moisture from the air resulting in a lowe...

  • Page 381

    Selection of lubricant use only the manufacturer’s recommended fluid. Refer to “fluids, lubricants, and genuine parts” in this section for the correct fluid type. Transfer case fluid level check inspect the transfer case for fluid leaks. If a fluid leak is found, the transfer case fluid level can be...

  • Page 382

    Caution! Using a transmission fluid other than the manufac- turer’s recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder. Using a transmission fluid other than the manufacturer’s recommended fluid will result in more frequent fluid and filter change...

  • Page 383

    Caution! • using a transmission fluid other than the manu- facturer’s recommended fluid may cause deterio- ration in transmission shift quality and/or torque converter shudder. Using a transmission fluid other than that recommended by the manufacturer will result in more frequent fluid and filter ch...

  • Page 384

    6. Remove the dipstick again, and note the fluid level on both sides. The fluid level should be between the “hot” (upper) reference holes on the dipstick at normal operat- ing temperature. The fluid level is only valid if there is a solid coating of oil on both sides of the dipstick. If the fluid is...

  • Page 385

    Maintenance after off-road driving after extended operation in mud, sand or water, or similar dirty conditions, have your brake discs, brake linings, and axle joints inspected and cleaned as soon as possible. This will prevent any abrasive material from causing excessive wear or unpredictable brakin...

  • Page 386

    What causes corrosion? Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle. The most common causes are: • road salt, dirt and moisture accumulation. • stone and gravel impact. • insects, tree sap and tar. • salt in the air near seacoast localities. ...

  • Page 387

    Special care • if you drive on salted or dusty roads or if you drive near the ocean, hose off the undercarriage at least once a month. • it is important that the drain holes in the lower edges of the doors, rocker panels and tailgate must be kept clear and open. • if you detect any stone chips or sc...

  • Page 388

    Stain repel fabric cleaning procedure — if equipped stain repel seats may be cleaned in the following man- ner: • remove as much of the stain as possible by blotting with a clean, dry towel. • blot any remaining stain with a clean, damp towel. • for tough stains, apply mopar威 total clean or a mild s...

  • Page 389

    Liquid. Please do not use polishes, oils, cleaning fluids, solvents, detergents, or ammonia-based cleaners to clean your leather upholstery. Application of a leather condi- tioner is not required to maintain the original condition. Warning! Do not use volatile solvents for cleaning purposes. Many ar...

  • Page 390

    1. Clean with a wet soft rag. A mild soap solution may be used, but do not use high alcohol content or abrasive cleaners. If soap is used, wipe clean with a clean damp rag. 2. Dry with a soft tissue. Seat belt maintenance do not bleach, dye or clean the belts with chemical solvents or abrasive clean...

  • Page 391

    Cavity cartridge fuse mini-fuse description 1 30 amp green audio amp (b+) 2 15 amp blue sunroof (b+) 3 10 amp red htd mirror (ebl) 4 20 amp yellow rr pwr out (b+) 5 10 amp red rr hvac (r/o) (commander only) 6 spare (b+) 7 20 amp yellow door locks (b+) 8 spare (b+) 9 20 amp yellow pwr outlet (b+) cav...

  • Page 392

    Cavity cartridge fuse mini-fuse description 14 20 amp yellow cigar ltr (r/a) 15 10 amp red tire pressure tran- sponders (r/o) 16 10 amp red upper & lower switch bank, diag. Connector, cluster (b+) 17 15 amp blue flipper glass (b+) 19 spare (r/s) 20 10 amp red steering column control module (sccm), c...

  • Page 393

    Underhood fuses (power distribution center) cavity cartridge fuse mini-fuse description 1 50 amp red ptc heater 1 (diesel only) 2 40 amp green hid headlamps 3 50 amp red ptc heater 2 (diesel only) 4 30 amp pink power outlets 5 50 amp red ptc heater 3 (diesel only) 6 30 amp pink cig lighter, trail to...

  • Page 394

    Cavity cartridge fuse mini-fuse description 9 20 amp blue front power win- dows 10 — spare 11 40 amp green hvac blower 12 30 amp pink rear wiper, ign r/o 13 40 amp green rear window de- froster (ebl)/heated mirror 14 30 amp pink rear hvac (if equipped) 15 — spare 16 50 amp red asd cavity cartridge f...

  • Page 395

    Cavity cartridge fuse mini-fuse description 25 20 amp yellow final drive control module (fdcm) 26 15 amp blue brake lamps 27 20 amp yellow hd washer (if equipped) (export only) 28 30 amp green abs valves 29 20 amp yellow pcm batt (gasoline only) 30 — spare 31 — spare 32 15 amp blue powertrain contro...

  • Page 396

    Cavity cartridge fuse mini-fuse description 41 20 amp yellow subwoofer (srt only) 42 — spare 43 25 amp natural coils, actuators 44 — spare underhood fuses (integrated power module) integrated power module 396 maintaining your vehicle.

  • Page 397

    Cavity cartridge fuse mini- fuse description 8 10 amp red lt park lamps 9 10 amp red trailer-tow park lamps 10 10 amp red rt park lamps 12 20 amp yellow front control module (fcm) batt #4 13 20 amp yellow front control module (fcm) batt #2 14 20 amp yellow adjustable pedal 15 20 amp yellow ft fog la...

  • Page 398

    Cavity cartridge fuse mini- fuse description 27 15 amp blue ignition off draw (iod) #1 — intrusion module, satellite video, steering con- trol module 28 20 amp yellow ignition off draw (iod) #2 — radio 29 10 amp red occupant restraint controller (orc) r/s 30 10 amp red occupant restraint controller ...

  • Page 399

    Replacement bulbs interior lights bulb type glove box lamp . . . . . . . . . . . . . . . . . . . . . . . . . 194 grab handle lamp . . . . . . . . . . . . . . . . L002825w5w overhead console reading lamps . . . . . . . . . Vt4976 rear cargo lamp . . . . . . . . . . . . . . . . . . . . . . . 214–2 vis...

  • Page 400

    Warning! A transient high tension occurs at the bulb sockets of high intensity discharge (hid) headlamps when the headlamp switch is turned on. It may cause serious electrical shock or electrocution if not serviced prop- erly. See your authorized dealer for service. Note: on vehicles equipped with h...

  • Page 401

    3. Disconnect the electrical connector and replace the bulb. Caution! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol. Front turn signal 1. Open the hood. 2. Turn t...

  • Page 402

    Caution! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol. Front fog lamp 1. Reach behind the front fascia from under the vehicle. 2. Turn the front fog lamp bulb on...

  • Page 403

    3. Squeeze the socket assembly tabs to remove it from the housing. 4. Pull the bulb to remove it from the socket. 5. Replace the bulb, reinstall the socket, and reattach the lamp assembly. 1 — tail/stop lamp bulb 3 — back-up lamp bulb 2 — tail/turn signal bulb 7 maintaining your vehicle 403.

  • Page 404

    Center high-mounted stop lamp (chmsl) 1. Remove the two screws securing the chmsl. 2. Twist the bulb socket to remove from the chmsl housing. 3. Pull the bulb out of the socket. 4. Replace the bulb, reinstall the socket and reattach the chmsl. 404 maintaining your vehicle.

  • Page 405

    Fluids and capacities u.S. Metric fuel (approximate) 3.7l and 5.7l engines 21 gallons 79 liters engine oil with filter 3.7l engine (sae 5w-20, api certified) 5 quarts 4.7 liters 5.7l engine (sae 5w-20, api certified) 7 quarts 6.6 liters cooling system * 3.7l engine (mopar 威 engine coolant/antifreeze...

  • Page 406

    Fluids, lubricants, and genuine parts engine component fluid, lubricant, or genuine part engine coolant mopar 威 antifreeze/coolant 5 year/100,000 mile formula hoat (hy- brid organic additive technology) or equivalent. Engine oil (3.7l and 5.7l engines) use api certified sae 5w-20 engine oil, meeting...

  • Page 407

    Chassis component fluid, lubricant, or genuine part automatic transmission mopar 威 atf+4 automatic transmission fluid or equivalent. Transfer case (nv140 single speed only) mopar 威 atf+4 automatic transmission fluid or equivalent. Transfer case (nv245 two speed only) mopar 威 nv 247/245 transfer case...

  • Page 409: Maintenance Schedules

    Maintenance schedules contents 䡵 emissions control system maintenance . . . . . 410 䡵 maintenance schedule . . . . . . . . . . . . . . . . . 410 ▫ required maintenance intervals . . . . . . . . . 412 8 m a i n t e n a n c e s c h e d u l e s.

  • Page 410

    Emissions control system maintenance the scheduled maintenance services listed in bold type must be done at the times or mileages specified to ensure the continued proper functioning of the emissions control system. These and all other maintenance services in- cluded in this manual, should be done t...

  • Page 411

    • change your engine oil more often if you drive your vehicle off-road for an extended period of time. • under no circumstances should oil change intervals exceed 6,000 miles (10,000 km) or 6 months, whichever comes first. Your authorized dealer will reset the oil change indicator message after comp...

  • Page 412

    Caution! Failure to perform the required maintenance items may result in damage to the vehicle. Required maintenance intervals refer to the maintenance schedules on the following pages for the required maintenance intervals. 8 m a i n t e n a n c e s c h e d u l e s 412 maintenance schedules.

  • Page 413

    6,000 miles (10,000 km) or 6 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. Odometer reading date repair order # dealer code signature authorized chrysler dealer 12,000 miles (20,000 km) or 12 months maintenance service schedule ❏ change the engine...

  • Page 414

    18,000 miles (30,000 km) or 18 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. ❏ inspect the front and rear axle fluid, change if using your vehicle for police, taxi, fleet, off-road or frequent trailer towing. Odometer reading date repair order # d...

  • Page 415

    30,000 miles (50,000 km) or 30 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. ❏ replace the engine air cleaner filter. ❏ replace the spark plugs (3.7l and 5.7l engines). ❏ adjust parking brake on vehicles equipped with four-wheel disc brakes. ❏ ins...

  • Page 416

    42,000 miles (70,000 km) or 42 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. Odometer reading date repair order # dealer code signature authorized chrysler dealer 48,000 miles (80,000 km) or 48 months maintenance service schedule ❏ change the engi...

  • Page 417

    54,000 miles (90,000 km) or 54 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. ❏ inspect the front and rear axle fluid, change if using your vehicle for police, taxi, fleet, off-road or frequent trailer towing. Odometer reading date repair order # d...

  • Page 418

    66,000 miles (110,000 km) or 66 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. Odometer reading date repair order # dealer code signature authorized chrysler dealer 72,000 miles (120,000 km) or 72 months maintenance service schedule ❏ change the en...

  • Page 419

    78,000 miles (130,000 km) or 78 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. Odometer reading date repair order # dealer code signature authorized chrysler dealer 84,000 miles (140,000 km) or 84 months maintenance service schedule ❏ change the en...

  • Page 420

    90,000 miles (150,000 km) or 90 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. ❏ replace the engine air cleaner filter. ❏ replace the spark plugs (3.7l and 5.7l engines). ❏ inspect and replace pcv valve if necessary. † ❏ adjust parking brake on veh...

  • Page 421

    96,000 miles (160,000 km) or 96 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. ❏ if using your vehicle for any of the following: dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. ❏ inspect the brake linings;...

  • Page 422

    108,000 miles (180,000 km) or 108 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. ❏ if using your vehicle for any of the following: dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. ❏ inspect the brake lining...

  • Page 423

    120,000 miles (200,000 km) or 120 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. ❏ replace the engine air cleaner filter. ❏ replace the ignition cables (3.7l engine). ❏ replace the spark plugs (3.7l and 5.7l engines). ❏ adjust parking brake on vehi...

  • Page 424

    132,000 miles (220,000 km) or 132 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. ❏ if using your vehicle for any of the following: dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. ❏ inspect the brake lining...

  • Page 425

    144,000 miles (240,000 km) or 144 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. ❏ if using your vehicle for any of the following: dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. ❏ inspect the brake lining...

  • Page 426

    † this maintenance is recommended by the manufacturer to the owner, but is not required to maintain emissions warranty. Warning! • you can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about...

  • Page 427: Contents

    If you need consumer assistance contents 䡵 suggestions for obtaining service for your vehicle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 429 ▫ prepare for the appointment . . . . . . . . . . . 429 ▫ prepare a list . . . . . . . . . . . . . . . . . . . . . . 429 ▫ be reasonable with r...

  • Page 428

    䡵 publication order forms . . . . . . . . . . . . . . . . 433 䡵 department of transportation uniform tire quality grades . . . . . . . . . . . . . . . . . . . . . . . . 435 ▫ treadwear . . . . . . . . . . . . . . . . . . . . . . . . . 435 ▫ traction grades . . . . . . . . . . . . . . . . . . . . . 4...

  • Page 429

    Suggestions for obtaining service for your vehicle prepare for the appointment if you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty. Discuss additional charges with the service manager. ...

  • Page 430

    This is why you should always talk to an authorized dealer’s service manager first. Most matters can be re- solved with this process. • if for some reason you are still not satisfied, talk to the general manager or owner of the authorized dealer- ship. They want to know if you need assistance. • if ...

  • Page 431

    Customer assistance for the hearing or speech impaired (tdd/tty) to assist customers who have hearing difficulties, the manufacturer has installed special tdd (telecommuni- cation devices for the deaf) equipment at its customer center. Any hearing or speech impaired customer, who has access to a tdd...

  • Page 432

    We appreciate that you have made a major investment when you purchased the vehicle. An authorized dealer has also made a major investment in facilities, tools, and training to assure that you are absolutely delighted with the ownership experience. You’ll be pleased with their sincere efforts to reso...

  • Page 433

    If nhtsa receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, nhtsa cannot become involved in individual problems between you, your authorized dealer, and the manufacturer. T...

  • Page 434

    • service manuals these comprehensive service manuals provide the in- formation that students and professional technicians need in diagnosing/troubleshooting, problem solving, maintaining, servicing, and repairing chrysler group llc vehicles. A complete working knowledge of the vehicle, system, and/...

  • Page 435

    Department of transportation uniform tire quality grades the following tire grading categories were established by the national highway traffic safety administration. The specific grade rating assigned by the tire’s manufacturer in each category is shown on the sidewall of the tires on your vehicle....

  • Page 436

    Temperature grades the temperature grades are a (the highest), b, and c, representing the tire’s resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the mater...

  • Page 437: Index

    Index 10

  • Page 438

    Abs (anti-lock brake system) . . . . . . . . . . . . . . 264 adding fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . 314 adjustable pedals . . . . . . . . . . . . . . . . . . . . . . . . 114 air cleaner, engine (engine air cleaner filter) . . . 365 air conditioner maintenance . . . . . . ....

  • Page 439

    Special additives . . . . . . . . . . . . . . . . . . . . . . 382 torque converter . . . . . . . . . . . . . . . . . . . . . . 249 autostick . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 244 auxiliary electrical outlet (power outlet) . . . . . . 138 auxiliary power outlet . . . . . . . ....

  • Page 440

    Cargo compartment . . . . . . . . . . . . . . . . . . . . . . 143 light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143 luggage carrier . . . . . . . . . . . . . . . . . . . . . . . 150 cargo light . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143 cargo load floor . . . ....

  • Page 441

    Coolant level . . . . . . . . . . . . . . . . . . . . . . . . . 377 disposal of used coolant . . . . . . . . . . . . . . . . 377 drain, flush, and refill . . . . . . . . . . . . . . . . . . 374 inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . 373 points to remember . . . . . . . . . ...

  • Page 442

    Electric remote mirrors . . . . . . . . . . . . . . . . . . . . 82 electrical outlet, auxiliary (power outlet) . . . . . . 138 electronic brake control system . . . . . . . . . . . . . 267 anti-lock brake system . . . . . . . . . . . . . . . . . 267 brake assist system . . . . . . . . . . . . . . . ...

  • Page 443

    Oil selection . . . . . . . . . . . . . . . . . . . . . . . 363,405 oil synthetic . . . . . . . . . . . . . . . . . . . . . . . . . 364 overheating . . . . . . . . . . . . . . . . . . . . . . . . . . 340 starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 238 temperature gauge . . . ....

  • Page 444

    Four wheel drive operation . . . . . . . . . . . . . . . . 251 four-way hazard flasher . . . . . . . . . . . . . . . . . . 340 freeing a stuck vehicle . . . . . . . . . . . . . . . . . . . 250 front axle (differential) . . . . . . . . . . . . . . . . . . . 380 front heated seats . . . . . . . . . . ...

  • Page 445

    Hands-free phone (uconnect 威) . . . . . . . . . . . . . . . 84 hazard warning flasher . . . . . . . . . . . . . . . . . . . 340 head restraints . . . . . . . . . . . . . . . . . . . . . . . . . . 88 head rests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88 headlights . . . . . . . . . ...

  • Page 446

    Interior lights . . . . . . . . . . . . . . . . . . . . . . . 105,108 intermittent wipers (delay wipers) . . . . . . . . . . . 111 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 inverter, power . . . . . . . . . . . . . . . . . . . . . . . . . 140 jack location . . . . . . ...

  • Page 447

    Bulb replacement . . . . . . . . . . . . . . . . . . . . . . 399 cargo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143 center mounted stop . . . . . . . . . . . . . . . . . . . 404 cruise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166 daytime running . . . . . . . . ...

  • Page 448

    Turn signal . . . . . . . . . . . . . . . . 74,101,107,401,402 vanity mirror . . . . . . . . . . . . . . . . . . . . . . . . . . 83 voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167 load floor, cargo . . . . . . . . . . . . . . . . . . . . . . . 147 loading vehicle . . . . . . . ...

  • Page 449

    Monitor, tire pressure system . . . . . . . . . . . . . . . 299 mopar parts . . . . . . . . . . . . . . . . . . . . . . . . . 361,432 multi-displacement engine system . . . . . . . . . . . 267 multi-function control lever . . . . . . . . . . . . . . . 101 new vehicle break-in period . . . . . . . . ...

  • Page 450

    Paint care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 385 paint damage . . . . . . . . . . . . . . . . . . . . . . . . . . 385 panic alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 park sense system, rear . . . . . . . . . . . . . . . . . . . 119 parking brake . . . ....

  • Page 451

    Rear axle (differential) . . . . . . . . . . . . . . . . . . . . 380 rear camera . . . . . . . . . . . . . . . . . . . . . . . . . . . 126 rear cupholder . . . . . . . . . . . . . . . . . . . . . . . . . 142 rear heated seats . . . . . . . . . . . . . . . . . . . . . . . . 90 rear park sense system ...

  • Page 452

    Safety checks inside vehicle . . . . . . . . . . . . . . . . . 73 safety checks outside vehicle . . . . . . . . . . . . . . . 74 safety defects, reporting . . . . . . . . . . . . . . . . . . 432 safety, exhaust gas . . . . . . . . . . . . . . . . . . . . . . . 72 safety information, tire . . . . . ....

  • Page 453

    Service assistance . . . . . . . . . . . . . . . . . . . . . . . 429 service contract . . . . . . . . . . . . . . . . . . . . . . . . . 431 service engine soon light (malfunction indicator) . . . . . . . . . . . . . . . . . . . . 159 service manuals . . . . . . . . . . . . . . . . . . . . . . . . 43...

  • Page 454

    Storage, vehicle . . . . . . . . . . . . . . . . . . . . . . 230,398 storing your vehicle . . . . . . . . . . . . . . . . . . . . . . 398 sun roof . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135 sun visor extension . . . . . . . . . . . . . . . . . . . . . . . 84 sunglasses storage ....

  • Page 455

    Radial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 293 replacement . . . . . . . . . . . . . . . . . . . . . . . . . 296 rotation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 298 safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 281 sizes . . . . . . . . ....

  • Page 456

    Transmitter programming (remote keyless entry) . . . . . . . . . . . . . . . . . . . . 21 transmitter, remote keyless entry (rke) . . . . . . . . 21 tread wear indicators . . . . . . . . . . . . . . . . . . . . 295 turn signals . . . . . . . . . . . . . . . . . . . 107,159,401,402 uci connector . . ...

  • Page 457

    Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 windshield defroster . . . . . . . . . . . . . . . . 74,221,227 windshield washers . . . . . . . . . . . . . . . . . . . . . . 109 fluid . . . . . . . . . . ....