1. DL manuals
  2. Jeep
  3. Automobile
  4. 2011 grand cherokee
  5. Owner's Manual

Jeep 2011 grand cherokee Owner's Manual

Summary of 2011 grand cherokee

  • Page 1

    Grand cherokee chrysler group llc o w n e r ’ s m a n u a l 2 0 1 1 2 0 1 1 g ra n d c h e ro k e e 11wk741-126-ab second edition printed in u.S.A..

  • Page 2

    291680.Ps 11jk72-126-aa chrysler 1" gutter 05/14/2010 06:18:00 vehicles sold in canada with respect to any vehicles sold in canada, the name chrysler group llc shall be deemed to be deleted and the name chrysler canada inc. Used in substitution therefore. Driving and alcohol drunken driving is one o...

  • Page 3: Table Of Contents

    Table of contents section page 1 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 things to know before starting your vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 3 understanding the featu...

  • Page 5: Introduction

    Introduction contents 䡵 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 䡵 rollover warning . . . . . . . . . . . . . . . . . . . . . . . 5 䡵 how to use this manual . . . . . . . . . . . . . . . . . . 6 䡵 warnings and cautions . . . . . . . . . . . . . . . . . . . 8 䡵 vehicle ide...

  • Page 6

    Introduction congratulations on selecting your new chrysler group llc vehicle. Be assured that it represents precision workmanship, distinctive styling, and high quality - all essentials that are traditional to our vehicles. This is a specialized utility vehicle, it can go places and perform tasks f...

  • Page 7

    Note: after reviewing the owner information, it should be stored in the vehicle for convenient referenc- ing and remain with the vehicle when sold. When it comes to service, remember that your authorized dealer knows your vehicle best, has factory-trained tech- nicians and genuine mopar 威 parts, and...

  • Page 8

    Failure to use the driver and passenger seat belts provided is a major cause of severe or fatal injury. In fact, the u.S. Government notes that the universal use of existing seat belts could cut the highway death toll by 10,000 or more each year and could reduce disabling injuries by two million ann...

  • Page 9

    Introduction 7.

  • Page 10

    Warnings and cautions this owner’s manual contains warnings against op- erating procedures that could result in a collision or bodily injury. It also contains cautions against proce- dures that could result in damage to your vehicle. If you do not read this entire manual, you may miss important info...

  • Page 11

    Note: it is illegal to remove or alter the vin. Vehicle modifications/alterations warning! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a accident resulting in serious injury or death. Vin location 1 introduction 9.

  • Page 13: Contents

    Things to know before starting your vehicle contents 䡵 a word about your keys . . . . . . . . . . . . . . . . . 14 ▫ wireless ignition node (win) . . . . . . . . . . . . 14 ▫ key fob . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 ▫ removing key fob from ignition . . . . . . . . . 16 ▫ key-...

  • Page 14

    ▫ remote open window feature — if equipped . . . . . . . . . . . . . . . . . . . . . . . . . 25 ▫ using the panic alarm . . . . . . . . . . . . . . . . . 26 ▫ programming additional transmitters . . . . . . 26 ▫ transmitter battery replacement . . . . . . . . . . 26 ▫ general information . . . . . ....

  • Page 15

    ▫ automatic locking retractor mode (alr) — if equipped . . . . . . . . . . . . . . . . . . . . . . . . . 60 ▫ seat belt pretensioners . . . . . . . . . . . . . . . . . 61 ▫ supplemental active head restraints (ahr) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 ▫ enhanced seat belt use...

  • Page 16

    A word about your keys your vehicle uses a keyless ignition system. This system consists of a key fob with remote keyless entry (rke) transmitter and a wireless ignition node (win) with integral ignition switch. You can insert the key fob into the ignition switch with either side up. Keyless enter-n...

  • Page 17

    Key fob the key fob operates the ignition switch. Insert the square end of the key fob into the ignition switch located on the instrument panel and rotate to the desired posi- tion. It also contains the remote keyless entry (rke) transmitter and an emergency key, which stores in the rear of the key ...

  • Page 18

    To remove the emergency key, slide the mechanical latch at the top of the key fob sideways with your thumb and then pull the key out with your other hand. Note: you can insert the double-sided emergency key into the lock cylinders with either side up. Removing key fob from ignition place the shift l...

  • Page 19

    • the power window switches, radio, power sunroof (if equipped), and power outlets will remain active for up to 10 minutes after the ignition switch is turned to the off position. Opening either front door will cancel this feature. The time for this feature is programmable. Refer to “electronic vehi...

  • Page 20

    Warning! • never leave children alone in a vehicle. Leaving unattended children in a vehicle is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Do not leave the key fob in the ignition or keyless enter-n-go in the acc or on/run mode. A child could operate ...

  • Page 21

    Sentry key 姞 the sentry key 威 immobilizer system prevents unauthor- ized vehicle operation by disabling the engine. The system does not need to be armed or activated. Operation is automatic, regardless of whether the vehicle is locked or unlocked. The system uses the factory-mated key fob with remot...

  • Page 22

    Replacement keys note: only key fobs that are programmed to the vehicle electronics can be used to start and operate the vehicle. Once a key fob is programmed to a vehicle, it cannot be programmed to any other vehicle. Caution! • always remove the key fobs from the vehicle and lock all doors when le...

  • Page 23

    • this device must accept any interference that may be received, including interference that may cause unde- sired operation. Vehicle security alarm — if equipped this vehicle security alarm monitors the vehicle doors, liftgate, liftgate flipper glass, and ignition for unauthor- ized operation. When...

  • Page 24

    Cancel the arming. If the vehicle security alarm success- fully arms, the vehicle security light will flash at a slower rate to indicate the alarm is set. Vehicles equipped with keyless enter-n-go press the keyless enter-n-go start/stop button until the electronic vehicle information center (evic) i...

  • Page 25

    Vehicles equipped with keyless enter-n-go either press the unlock button on the rke transmitter, pull on the front driver or passenger door handle (refer to “keyless enter-n-go” in “things to know before start- ing your vehicle” for further information) with a valid key fob in range, or press the ke...

  • Page 26

    Note: inserting the key fob with rke transmitter into the ignition switch disables the system from responding to any button presses from that rke transmitter. Driving at speeds 5 mph (8 km/h) and above disables the system from responding to all rke transmitter buttons for all rke transmitters. To un...

  • Page 27

    Flash lamps with remote key lock this feature will cause the turn signal lamps to flash when the doors are locked or unlocked with the rke transmitter. This feature can be turned on or off. To change the current setting, refer to “electronic vehicle information center (evic)/personal settings (custo...

  • Page 28

    Then immediately press and hold the unlock button until the windows lower to the level desired or until they lower completely. Using the panic alarm to turn the panic alarm feature on or off, press and hold the panic button on the rke transmitter for at least one second and release. When the panic a...

  • Page 29

    1. Remove the emergency key by sliding the mechanical latch at the top of the rke transmitter sideways with your thumb and then pull the key out with your other hand. 2. Insert the tip of the emergency key or a #2 flat blade screwdriver into the slot and gently pry the two halves of the rke transmit...

  • Page 30

    3. Remove and replace the battery. When replacing the battery, match the + sign on the battery to the + sign on the inside of the battery clip, located on the back cover. Avoid touching the new battery with your fingers. Skin oils may cause battery deterioration. If you touch a battery, clean it wit...

  • Page 31

    If your rke transmitter fails to operate from a normal distance, check for these two conditions: 1. A weak battery in the rke transmitter. The expected life of the battery is a minimum of three years. 2. Closeness to a radio transmitter such as a radio station tower, airport transmitter, and some mo...

  • Page 32

    Warning! • do not start or run an engine in a closed garage or confined area. Exhaust gas contains carbon mon- oxide (co) which is odorless and colorless. Car- bon monoxide is poisonous and can cause serious injury or death when inhaled. • keep remote keyless entry (rke) transmitters away from child...

  • Page 33

    Note: • if an engine fault is present or fuel level is low, the vehicle will start and then shutdown in 10 seconds. • the park lamps will turn on and remain on during remote start mode. • for security, power window and power sunroof op- eration (if equipped) are disabled when the vehicle is in the r...

  • Page 34

    Note: • for vehicles not equipped with keyless enter-n-go feature, the ignition switch must be in the on/run position in order to drive the vehicle. • for vehicles not equipped with keyless enter-n-go feature, the message “remote start active — insert key and turn to run” will display in the evic un...

  • Page 35

    Door locks the power door locks can be manually locked or un- locked from inside the vehicle by using the door lock knob. If the lock knob is down when the door is closed, the door will lock. Therefore, make sure the key is not inside the vehicle before closing the door. Warning! • for personal secu...

  • Page 36

    Power door locks the power door lock switch is located on each front door panel. Press the switch to lock or unlock the doors. If the lock knob is down when the door is closed, the door will lock. Therefore, make sure the key fob is not inside the vehicle before closing the door. If you press the do...

  • Page 37

    Automatic unlock on exit feature — if equipped if auto unlock is enabled, this feature will unlock all the doors when the driver’s door is opened if the vehicle is stopped and in park or neutral. Refer to “electronic vehicle information center (evic)/personal settings (customer-programmable features...

  • Page 38

    Warning! Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child-protection locks are engaged (locked). Note: for emergency exit from the rear seats when the child-protection door lock system is engaged, manually raise the do...

  • Page 39

    • if a passive entry door handle has not been used for 72 hours, the passive entry feature for the handle may time out. Pulling the deactivated front door handle will reactivate the door handle’s passive entry feature. • if wearing gloves on your hands, or if it has been raining on the passive entry...

  • Page 40

    To unlock from the passenger side: with a valid passive entry rke transmitter within 5 ft (1.5 m) of the passenger door handle, grab the front passenger door handle to unlock all four doors automati- cally. The interior door panel lock knob will raise when the door is unlocked. Note: all doors will ...

  • Page 41

    To enter the liftgate with a valid passive entry rke transmitter within 3 ft (1.0 m) of the liftgate, press the button on the right side of the chrome accent bar, which is located on the liftgate below the flipper glass to lock or unlock the vehicle. Note: if “unlock all doors 1st press” is programm...

  • Page 42

    To lock the vehicle’s doors the front door handles have lock buttons located on the outside of the handle. With one of the vehicle’s passive entry rke transmitters within 5 ft (1.5 m) of the driver or passenger front door handle, press the door handle lock button to lock all four doors and liftgate....

  • Page 43

    Windows power windows the power window controls are located on the driver’s door trim panel. There is a single switch on the front passenger door and rear doors which operate the front passenger and rear passenger door windows. The win- dow controls will operate only when the ignition switch is in t...

  • Page 44

    Warning! Never leave children in a vehicle with the key in the ignition switch or leave a vehicle with keyless enter- n-go in the acc or on/run position. Occupants, particularly unattended children, can become en- trapped by the windows while operating the power window switches. Such entrapment may ...

  • Page 45

    During auto up. If this happens, pull the switch lightly to the first detent and hold it to close the window manually. Warning! There is no anti-pinch protection when the window is almost closed. Be sure to clear all objects from the window before closing. Resetting the auto up feature should the au...

  • Page 46

    Wind buffeting wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions. This is a normal occur- rence and ...

  • Page 47

    Liftgate flipper glass the liftgate flipper glass is also unlocked when the liftgate is unlocked. To open the flipper glass, push up on the window switch located on the liftgate. Once the liftgate flipper glass has been opened, connec- tion to the rear window wiper is interrupted, preventing activat...

  • Page 48

    Power liftgate — if equipped the power liftgate may be opened by pulling up on the liftgate handle or by pressing the liftgate button on the remote keyless entry (rke) transmitter. Press the liftgate button on the rke transmitter twice within five seconds, to open the power liftgate. Once the liftga...

  • Page 49

    Warning! During power operation, personal injury or cargo damage may occur. Ensure the liftgate travel path is clear. Make sure the liftgate is closed and latched before driving away. Note: • if anything obstructs the power liftgate while it is closing or opening, the liftgate will automatically rev...

  • Page 50

    • if the power liftgate encounters multiple obstructions within the same cycle, the system will automatically stop and the liftgate must be opened or closed manu- ally. • if your liftgate is power closing and you put the vehicle in gear, the liftgate will continue to power close. However, vehicle mo...

  • Page 51

    • supplemental active head restraints (ahr) located on top of the front seats (integrated into the head restraint) • supplemental side airbag inflatable curtains (sabic) for the driver and passengers seated next to a window • supplemental seat-mounted side airbags (sab) • an energy-absorbing steerin...

  • Page 52

    Here are some simple steps you can take to minimize the risk of harm from a deploying airbag: 1. Children 12 years old and under should always ride buckled up in a rear seat. Warning! Infants in rear facing child restraints should never ride in the front seat of a vehicle with a passenger advanced f...

  • Page 53

    4. Do not lean against the door or window. If your vehicle has side airbags, and deployment occurs, the side airbags will inflate forcefully into the space be- tween you and the door. 5. If the airbag system in this vehicle needs to be modified to accommodate a disabled person, contact the customer ...

  • Page 54

    Buckle up even though you are an excellent driver, even on short trips. Someone on the road may be a poor driver and cause an accident that includes you. This can happen far away from home or on your own street. Research has shown that seat belts save lives, and they can reduce the seriousness of in...

  • Page 55

    Warning! (continued) • it is dangerous to ride in a cargo area, inside or outside of a vehicle. In an accident, people riding in these areas are more likely to be seriously injured or killed. • do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • ...

  • Page 56

    3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” warning! • a belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your bel...

  • Page 57

    Warning! (continued) • a belt that is worn under your arm is dangerous. Your body could strike the inside surfaces of the vehicle in an accident, increasing head and neck injury. A belt worn under the arm can cause internal injuries. Ribs aren’t as strong as shoulder bones. Wear the belt over your s...

  • Page 58

    5. Position the shoulder belt on your chest so that it is comfortable and not resting on your neck. The retractor will withdraw any slack in the belt. 6. To release the belt, push the red button on the buckle. The belt will automatically retract to its stowed position. If necessary, slide the latch ...

  • Page 59

    Lap/shoulder belt untwisting procedure use the following procedure to untwist a twisted lap/ shoulder belt. 1. Position the latch plate as close as possible to the anchor point. 2. At about 6 to 12 in (15 to 30 cm) above the latch plate, grasp and twist the belt webbing 180 degrees to create a fold ...

  • Page 60

    As a guide, if you are shorter than average, you will prefer a lower position, and if you are taller than average, you will prefer a higher position. When you release the button, verify the shoulder belt anchorage is latched by pulling downward on the shoulder belt anchorage until it is locked into ...

  • Page 61

    Seat belts in passenger seating positions the seat belts in the passenger seating positions are equipped with automatic locking retractors (alr) which are used to secure a child restraint system. For additional information refer to “installing child re- straints using the vehicle seat belt” under th...

  • Page 62

    Automatic locking retractor mode (alr) — if equipped in this mode, the shoulder belt is automatically pre- locked. The belt will still retract to remove any slack in the shoulder belt. The automatic locking mode is avail- able on all passenger-seating positions with a combina- tion lap/shoulder belt...

  • Page 63

    Seat belt pretensioners the seat belts for both front seating positions are equipped with pretensioning devices that are designed to remove slack from the seat belt in the event of an accident. These devices may improve the performance of the seat belt by assuring that the belt is tight about the oc...

  • Page 64

    When ahrs deploy during a rear impact, the front half of the head restraint extends forward to minimize the gap between the back of the occupant’s head and the ahr. This system is designed to help prevent or reduce the extent of injuries to the driver and front passenger in certain types of rear imp...

  • Page 65

    Caution! All occupants, including the driver, should not oper- ate a vehicle or sit in a vehicle’s seat until the head restraints are placed in their proper positions in order to minimize the risk of neck injury in the event of an accident. Note: for more information on properly adjusting and positi...

  • Page 66

    3. Pull down then rearward towards the rear of the vehicle then down to engage the locking mechanism. 4. The ahr front soft foam and trim half should lock into the back decorative plastic half. 1 — downward movement 2 — rearward movement 3 — final downward movement to engage locking mechanism 64 thi...

  • Page 67

    Note: • if you have difficulties or problems resetting the active head restraints, see an authorized dealer. • for safety reasons, have the active head restraints checked by a qualified specialist at an authorized dealer. Enhanced seat belt use reminder system (beltalert 姞 ) beltalert 威 is a feature...

  • Page 68

    The front passenger seat beltalert 威 is not active when the front passenger seat is unoccupied. Beltalert 威 may be triggered when an animal or heavy object is on the front passenger seat or when the seat is folded flat (if equipped). It is recommended that pets be restrained in the rear seat in pet ...

  • Page 69

    Note: although beltalert 威 has been deactivated, the seat belt reminder light will continue to illuminate while the driver’s or front passenger’s (if equipped with belt alert) seat belt remains unfastened. Seatbelt lock out the center rear seat belt system has a lock out feature that will not allow ...

  • Page 70

    Supplemental restraint system (srs) — airbags this vehicle has advanced front airbags for both the driver and front passenger as a supplement to the seat belt restraint systems. The driver’s advanced front air- bag is mounted in the center of the steering wheel. The passenger’s advanced front airbag...

  • Page 71

    This vehicle may be equipped with driver and/or front passenger seat track position sensors that may adjust the inflation rate of the advanced front airbags based upon seat position. This vehicle may be equipped with a driver and/or front passenger seat belt buckle switch that detects whether the dr...

  • Page 72

    Airbag system components your vehicle may be equipped with the following airbag system components: • occupant restraint controller (orc) • airbag warning light • steering wheel and column • instrument panel • knee impact bolster • driver advanced front airbag • passenger advanced front airbag • supp...

  • Page 73

    Warning! • no objects should be placed over or near the airbag on the instrument panel, because any such objects could cause harm if the vehicle is in a collision severe enough to cause the airbag to inflate. • do not put anything on or around the airbag covers or attempt to open them manually. You ...

  • Page 74

    When the airbag deploys, it opens the seam between the front and side of the seat’s trim cover. Each airbag deploys independently, that is a left side impact deploys the left airbag only and a right-side impact deploys only the right airbag. Supplemental side airbag inflatable curtain (sabic) sabic ...

  • Page 75

    • being too close to the sab and sabic airbags during deployment could cause you to be severely injured or killed. • should a vehicle rollover occur, the pretensioners, sab and/or sabic airbags on both sides of the vehicle may deploy. The system includes side impact sensors adjacent to both front an...

  • Page 76

    Warning! (continued) • if your vehicle is equipped with sabic airbags, do not have any accessory items installed which will alter the roof, including adding a sunroof to your vehicle. Do not add roof racks that require permanent attachments (bolts or screws) for instal- lation on the vehicle roof. D...

  • Page 77

    The advanced front airbags will not deploy in all frontal collisions, including some that may produce substantial vehicle damage — for example, some pole collisions, truck underrides, and angle offset collisions. On the other hand, depending on the type and location of impact, advanced front airbags...

  • Page 78

    It also includes diagnostics that will illuminate the instru- ment cluster airbag warning light if a malfunction is noted that could affect the airbag system. The diagnostics also record the nature of the malfunction. Warning! Ignoring the airbag warning light in your instru- ment panel could mean y...

  • Page 79

    Supplemental seat-mounted side airbag (sab) inflator units the supplemental seat-mounted side airbags are de- signed to activate only in certain side collisions. The orc determines if a side collision requires the side airbags to inflate based on the severity and type of collision. Based on the seve...

  • Page 80

    Because airbag sensors estimate deceleration over time, vehicle speed and damage are not good indicators of whether or not an airbag should have deployed. Note: in a rollover the pretensioners, sab and/or sabic airbags may deploy on both sides of the vehicle. Front and side impact sensors in front a...

  • Page 81

    Passenger as the airbags deploy and unfold. The abrasions are similar to friction rope burns or those you might get sliding along a carpet or gymnasium floor. They are not caused by contact with chemicals. They are not permanent and normally heal quickly. However, if you haven’t healed significantly...

  • Page 82

    Maintaining your airbag system warning! • modifications to any part of the airbag system could cause it to fail when you need it. You could be injured if the airbag system is not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the stee...

  • Page 83

    Airbag warning light you will want to have the airbags ready to inflate for your protection in a collision. The airbag warning light monitors the internal circuits and interconnecting wiring associated with airbag system electrical components. While the airbag system is designed to be maintenance fr...

  • Page 84

    • whether or not the driver and passenger safety belts were buckled/fastened; • how far (if at all) the driver was depressing the accelerator and/or brake pedal; and, • how fast the vehicle was traveling. These data can help provide a better understanding of the circumstances in which crashes and in...

  • Page 85

    There are different sizes and types of restraints for children from newborn size to the child almost large enough for an adult safety belt. Always check the child seat owner’s manual to ensure you have the right seat for your child. Use the restraint that is correct for your child. Warning! In a col...

  • Page 86

    Warning! • rearward-facing child seats must never be used in the front seat of a vehicle with the front passenger airbag unless the airbag is turned off. An airbag deployment could cause severe injury or death to infants in this position. • improper installation can lead to failure of an infant or c...

  • Page 87

    Restraint and slide the latch plate into the buckle. Then, pull the shoulder belt until it is fully extended from the retractor. Allow the belt to return into the retractor, pulling on the excess webbing to tighten the lap portion around the child restraint. For additional information refer to ⬙auto...

  • Page 88

    The belt-positioning booster seat is for children weighing more than 40 lbs (18 kg), but who are still too small to fit the vehicle’s seat belts properly. If the child cannot sit with knees bent over the vehicle’s seat cushion while the child’s back is against the seatback, they should use a belt-po...

  • Page 89

    Latch-compatible child restraint systems are now avail- able. However, because the lower anchorages are to be introduced over a period of years, child restraint systems having attachments for those anchorages will continue to also have features for installation using the vehicle’s seat belts. Child ...

  • Page 90

    If you are installing latch-compatible child restraints in adjacent rear seating positions, you can use the latch anchors or the vehicle’s seat belt for the outboard position, but you must use the vehicle’s seat belt at the center position. If your child restraints are not latch- compatible, you can...

  • Page 91

    In addition, there are top tether strap anchorages behind each rear seating position located on the back of the seat. To access the top tether strap anchorages behind the rear seat, pull the carpeted floor panel away from the seat back, this will expose the top tether strap anchorages. Warning! Do n...

  • Page 92

    Many, but not all restraint systems will be equipped with separate straps on each side, with each having a hook or connector for attachment to the lower anchorage and a means of adjusting the tension in the strap. Forward- facing toddler restraints and some rear-facing infant restraints will also be...

  • Page 93

    Installing child restraints using the vehicle seat belts the passenger seat belts are equipped with either cinch- ing latch plates or automatic locking retractors (alr), which are designed to keep the lap portion tight around the child restraint so that it is not necessary to use a locking clip. If ...

  • Page 94

    To attach a child restraint tether strap: for rearward facing infant seats secured in the center seat position with the vehicle seat belts, the rear center seat position has an armrest tether that secures the arm rest in the upward position. To access the center seat arm rest tether first lower the ...

  • Page 95

    For center seating position route the tether strap over the seatback and headrest then attach the hook to the tether anchor located on the back of the seat. For the outboard seating positions, route the tether under the head rests, and attach the hook to the top tether anchor located on the back of ...

  • Page 96

    Top tether strap anchorage (located on seatback) top tether strap mounting 94 things to know before starting your vehicle.

  • Page 97

    Warning! • an incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchor positions directly be- hind the child seat to secure a child restraint top tether strap. • do not use the cargo tie downs located on the load floor. Improper usag...

  • Page 98

    While cruising, brief full-throttle acceleration within the limits of local traffic laws, contributes to a good break-in. Wide-open throttle acceleration in low gear can be detri- mental and should be avoided. The engine oil installed in the engine at the factory is a high-quality energy conserving ...

  • Page 99

    Exhaust gas warning! Exhaust gases can injure or kill. They contain carbon monoxide (co), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing (co) follow these safety tips: do not run the engine in a closed garage or in confined ar...

  • Page 100

    Safety checks you should make inside the vehicle seat belts inspect the belt system periodically, checking for cuts, frays, and loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Front seat belt assemblies must be replaced after a collision. Rear seat b...

  • Page 101

    Warning! Pedals that cannot move freely can cause loss of vehicle control and increase the risk of serious per- sonal injury. • always make sure that floor mats are properly attached to the floor mat fasteners. • never place or install floor mats or other floor coverings in the vehicle that cannot b...

  • Page 102

    Periodic safety checks you should make outside the vehicle tires examine tires for excessive tread wear and uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread. Inspect the tread and sidewall for cuts and cracks. Check the wheel nuts for tightness. Check the ti...

  • Page 103: Contents

    Understanding the features of your vehicle contents 䡵 mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108 ▫ inside day/night mirror . . . . . . . . . . . . . . . 108 ▫ automatic dimming mirror — if equipped . . 109 ▫ outside mirrors . . . . . . . . . . . . . . . . . . . . . 110 ▫ o...

  • Page 104

    ▫ passenger’s power seat . . . . . . . . . . . . . . . . 124 ▫ power lumbar — if equipped . . . . . . . . . . . 125 ▫ manual front seats forward/rearward adjustment . . . . . . . . . . . . . . . . . . . . . . . . 126 ▫ manual front passenger seatback adjustment — recline . . . . . . . . . . . . . . ...

  • Page 105

    ▫ daytime running lights — if equipped . . . . 149 ▫ automatic headlight leveling — hid headlights only . . . . . . . . . . . . . . . . . . . . . 149 ▫ headlight delay . . . . . . . . . . . . . . . . . . . . . 149 ▫ parking lights and panel lights . . . . . . . . . 150 ▫ fog lights — if equipped . ....

  • Page 106

    䡵 electronic speed control . . . . . . . . . . . . . . . . 163 ▫ to activate . . . . . . . . . . . . . . . . . . . . . . . . . 165 ▫ to set a desired speed . . . . . . . . . . . . . . . . 165 ▫ to deactivate . . . . . . . . . . . . . . . . . . . . . . . 165 ▫ to resume speed . . . . . . . . . . . . ...

  • Page 107

    䡵 parksense威 rear park assist — if equipped . . . 195 ▫ parksense威 sensors . . . . . . . . . . . . . . . . . . . 195 ▫ parksense威 warning display . . . . . . . . . . . . 195 ▫ parksense威 display . . . . . . . . . . . . . . . . . . . 196 ▫ enabling and disabling parksense威 . . . . . . . 200 ▫ service...

  • Page 108

    䡵 power sunroof — if equipped . . . . . . . . . . . . 214 ▫ opening sunroof — express . . . . . . . . . . . . 215 ▫ closing sunroof — express . . . . . . . . . . . . . 215 ▫ pinch protect feature . . . . . . . . . . . . . . . . . 215 ▫ pinch protect override . . . . . . . . . . . . . . . . 216 ▫ ven...

  • Page 109

    䡵 electrical power outlets . . . . . . . . . . . . . . . . . 221 䡵 power inverter — if equipped . . . . . . . . . . . . 226 䡵 cupholders . . . . . . . . . . . . . . . . . . . . . . . . . . 228 䡵 storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 229 ▫ glove compartment . . . . . . . ....

  • Page 110

    Mirrors inside day/night mirror a single ball joint mirror is provided in the vehicle. It is a twist on mirror that has a fixed position. The mirror head can be adjusted up, down, left, and right for various drivers. The mirror should be adjusted to center on the view through the rear window. Headli...

  • Page 111

    Automatic dimming mirror — if equipped this mirror automatically adjusts for headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light in the button will illuminate to indicate when the dim- ming feature is activated. The m...

  • Page 112

    Outside mirrors to receive maximum benefit, adjust the outside mirrors to center on the adjacent lane of traffic with a slight overlap of the view obtained on the inside mirror. Warning! Vehicles and other objects seen in the passenger side convex mirror will look smaller and farther away than they ...

  • Page 113

    Mirror, press the mirror select button for the mirror that you want to adjust. Using the mirror control switch, press on any of the four arrows for the direction that you want the mirror to move. Power mirror preselected positions can be controlled by the optional memory seat feature. Refer to “driv...

  • Page 114

    Lift the cover to reveal the mirror. The light will turn on automatically. Sun visor extension — if equipped this feature has a pull out extension on the sun visor for increased coverage. Blind spot monitoring — if equipped the blind spot monitoring (bsm) system uses two radar- based sensors, locate...

  • Page 115

    When the vehicle is started, the bsm warning light will momentarily illuminate in both outside rear view mirrors to let the driver know that the system is operational. The bsm system sensors operate when the vehicle is in any forward gear or reverse and enters stand by mode when the vehicle is in pa...

  • Page 116

    The area on the rear fascia where the radar sensors are located must remain free of snow, ice, and dirt/road contamination so that the bsm system can function properly. Do not block the area of the rear fascia where the radar sensors are located with foreign objects (bum- per stickers, bicycle racks...

  • Page 117

    The bsm system can also be configured to sound an audible (chime) alert and reduces the radio volume to notify the driver of objects that have entered the detec- tion zones. Refer to “modes of operation” for further information. The bsm system monitors the detection zone from three different entry p...

  • Page 118

    Entering from the rear vehicles that come up from behind your vehicle on either side and enter the rear detection zone with a relative speed of less than 30 mph (48 km/h). Overtaking traffic if you pass another vehicle slowly (with a relative speed less than 10 mph (16 km/h) and the vehicle remains ...

  • Page 119

    The bsm system is designed not to issue an alert on stationary objects such as guardrails, posts, walls, foliage, berms, etc. However, occasionally the system may alert on such objects. This is normal operation and your vehicle does not require service. Overtaking/passing stationary objects 3 unders...

  • Page 120

    The bsm system will not alert you of objects that are traveling in the opposite direction of the vehicle in adjacent lanes. Warning! The blind spot monitoring system is only an aid to help detect objects in the blind spot zones. The bsm system is not designed to detect pedestrians, bicy- clists, or ...

  • Page 121

    Rcp monitors the rear detection zones on both sides of the vehicle, for objects that are moving toward the side of the vehicle with a minimum speed of approximately 1 to 2 mph (1 km/h to 3 km/h), to objects moving a maxi- mum of approximately 10 mph (16 km/h), such as in parking lot situations. Note...

  • Page 122

    Modes of operation three selectable modes of operation are available in the electronic vehicle information center (evic). Refer to “electronic vehicle information center (evic)/personal settings (customer-programmable features)” in “under- standing your instrument panel” for further information. Bli...

  • Page 123

    Blind spot alert off when the bsm system is turned off there will be no visual or audible alerts from either the bsm or rcp systems. Note: the bsm system will store the current operating mode when the vehicle is shut off. Each time the vehicle is started the previously stored mode will be recalled a...

  • Page 124

    Warning! (continued) • do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. In a collision, people riding in these areas are more likely to be seriously injured or killed. • be sure everyone in your vehicle is in a seat and using a seat belt properl...

  • Page 125

    Adjusting the seat forward or rearward the seat can be adjusted both forward and rearward. Push the seat switch forward or rearward, the seat will move in the direction of the switch. Release the switch when you have reached the desired position. Adjusting the seat up or down the height of the seats...

  • Page 126

    Warning! (continued) • do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt, which could result in serious injury or death. Caution! Do not place any article under a power seat or impede its abili...

  • Page 127

    Tilting the seat up or down the angle of the seat cushion can be adjusted up or down. Pull upward or push downward on the front of the seat switch, the front of the seat cushion will move in the direction of the switch. Release the switch when you have reached the desired position. Warning! • adjust...

  • Page 128

    Push the switch rearward to decrease the lumbar sup- port. Pushing upward or downward on the switch will raise and lower the position of the support. Manual front seats forward/rearward adjustment some models may be equipped with manual front driver or passenger seats. The seats can be adjusted forw...

  • Page 129

    While sitting in the seat, lift up on the bar located under the seat cushion and move the seat forward or rearward. Release the bar once you have reached the desired position. Then, using body pressure, move forward and rearward on the seat to be sure that the seat adjusters have latched. Warning! •...

  • Page 130

    Warning! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt, which could result in serious injury or death. Front passenger seat fold-flat feature — if equipped to fold the seatback to the flat ...

  • Page 131

    Heated seats — if equipped on some models, the front and rear seats may be equipped with heaters in both the seat cushions and seatbacks. Warning! • persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, ex- ha...

  • Page 132

    You can choose from high, low or off heat settings. Amber indicator lights in each switch indicate the level of heat in use. Two indicator lights will illuminate for high, one for low and none for off. Press the switch once to select high-level heating. Press the switch a second time to select low-l...

  • Page 133

    You can choose from high, low or off heat settings. Amber indicator lights in each switch indicate the level of heat in use. Two indicator lights will illuminate for high, one for low and none for off. Press the switch once to select high-level heating. Press the switch a second time to select low-l...

  • Page 134

    The ventilated seat switches are used to control the speed of the fans located in the seat. Press the switch once to choose high, press it a second time to choose low. Pressing the switch a third time will turn the ventilated seat off. When high speed is selected both lights on the switch will be il...

  • Page 135

    Active head restraints — front seats active head restraints are passive, deployable compo- nents, and vehicles with this equipment cannot be readily identified by any markings, only through visual inspec- tion of the head restraint. The head restraint will be split in two halves, with the front half...

  • Page 136

    For comfort the active head restraints can be tilted forward and rearward. To tilt the head restraint closer to the back of your head, pull forward on the bottom of the head restraint. Push rearward on the bottom of the head restraint to move the head restraint away from your head. Note: • the head ...

  • Page 137

    • in the event of deployment of an active head re- straint, refer to “occupant restraints/resetting active head restraints (ahr)” in “things to know before starting your vehicle” for further information. Warning! • do not place items over the top of the active head restraint, such as coats, seat cov...

  • Page 138

    The center head restraint has limited adjustment. Lift upward on the head restraint to raise it, or push down- ward on the head restraint to lower it. Warning! Sitting in a seat with the head restraint in its lowered position could result in serious injury or death in a collision. Always make sure t...

  • Page 139

    60/40 split rear seat to lower rear seat either side of the rear seat can be lowered to allow for extended cargo space and still maintain some rear seating room. Note: be sure that the front seats are fully upright and positioned forward. This will allow the rear seatback to fold down easily. 1. Pul...

  • Page 140

    2. Fold the rear seat completely forward. To raise rear seat raise the rear seatback and lock it into place. If interfer- ence from the cargo area prevents the seatback from fully locking, you will have difficulty returning the seat to its proper position. Warning! • be certain that the seatback is ...

  • Page 141

    Reclining rear seat to recline the seatback, lift the lever located on the outboard side of the seat, lean back and release the lever at the desired position. To return the seatback, lift the lever, lean forward and release the lever. Warning! Do not ride with the seatback reclined so that the shoul...

  • Page 142

    Driver memory seat — if equipped once programmed, the memory buttons 1 and 2 on the driver’s door panel can be used to recall the driver’s seat, driver’s outside mirror, adjustable steering wheel posi- tion (if equipped), and the radio station preset settings. Your remote keyless entry (rke) transmi...

  • Page 143

    Setting memory positions and linking remote keyless entry transmitter to memory note: each time the s (set) button and a numbered button 1 or 2 are pressed, you erase the memory settings for that button and store a new one. 1. Insert the ignition key, and turn the ignition switch to the on position....

  • Page 144

    11. Select ⬙remote linked to memory⬙ in the electronic vehicle information center (evic) and enter ⬙yes⬙. Refer to “electronic vehicle information center (evic)/ customer-programmable features” in “understanding your instrument panel” for further information. 12. Repeat the above steps to set the ne...

  • Page 145

    3. Press and release the memory s (set) button located on the driver’s door. 4. Within five seconds, press and release memory button 1 on the driver’s door. 5. Within five seconds, press and release the unlock button on the rke transmitter. To disable another rke transmitter linked to either memory ...

  • Page 146

    Driving position when the key is placed into the ignition, and turned out of the lock position toward the acc/on position. The easy entry/exit feature will be automatically dis- abled if the seat is already positioned closer than 0.9 in (23 mm) forward of the rear stop. At this position, there is no...

  • Page 147

    2. Reach under the hood, move safety latch to the left and lift the hood. Caution! To prevent possible damage, do not slam the hood to close it. Use a firm downward push at the center of the hood to ensure that both latches engage. Warning! Be sure the hood is fully latched before driving your vehic...

  • Page 148

    Lights headlight switch the headlight switch is located on the left side of the instrument panel, next to the steering wheel. The head- light switch controls the operation of the headlights, parking lights, instrument panel lights, cargo lights and fog lights (if equipped). To turn on the headlights...

  • Page 149

    Caution! Do not use abrasive cleaning components, solvents, steel wool or other abrasive materials to clean the lenses. Automatic headlights — if equipped this system automatically turns the headlights on or off according to ambient light levels. To turn the system on, rotate the headlight switch to...

  • Page 150

    Note: when your headlights come on during the daytime, the instrument panel lights will automatically dim to the lower nighttime intensity. Refer to “lights” in this section for further information. Smartbeam™ — if equipped the smartbeam™ system provides increased forward lighting at night by automa...

  • Page 151

    2. Push back on the multifunction lever once again to reactivate the system. Note: broken, muddy, or obstructed headlights and taillights of vehicles in the field of view will cause headlights to remain on longer (closer to the vehicle). Also, dirt, film, and other obstructions (sticker, toll box, e...

  • Page 152

    The headlight delay time is programmable on vehicles equipped with an electronic vehicle information center (evic). Refer to “electronic vehicle information center (evic)/customer-programmable features” in “under- standing your instrument panel” for further information. Parking lights and panel ligh...

  • Page 153

    Interior lights courtesy and dome lights are turned on when the front doors are opened, when the dimmer control (rotating wheel on the right side of the headlight switch) is rotated to the its farthest upward position, or if equipped, when the unlock button is pressed on the remote keyless entry (rk...

  • Page 154

    Lights-on reminder if the headlights, parking lights, or cargo lights are left on after the ignition is turned off, a chime will sound when the driver’s door is opened. Battery saver to protect the life of your vehicle’s battery, load shedding is provided for both the interior and exterior lights. I...

  • Page 155

    Each light can be turned on by pressing a switch on either side of the console. These buttons are backlit for night time visibility. To turn the lights off, press the switch a second time. The lights will also turn on when the unlock button on the remote keyless entry (rke) is pressed. Ambient light...

  • Page 156

    Multifunction lever the multifunction lever is located on the left side of the steering column. Turn signals move the multifunction lever up or down and the arrows on each side of the instrument cluster flash to show proper operation of the front and rear turn signal lights. Note: if either light re...

  • Page 157

    High/low beam switch push the multifunction lever toward the instrument panel to switch the headlights to high beam. Pulling the multifunction back toward the steering wheel will turn the low beams back on, or shut the high beams off. Windshield wipers and washers the windshield wiper/washer control...

  • Page 158

    Windshield wiper operation rotate the end of the lever to one of the first four detent positions for intermittent settings, the fifth detent for low wiper operation and the sixth detent for high wiper operation. Caution! Always remove any buildup of snow that prevents the windshield wiper blades fro...

  • Page 159

    Note: if the vehicle is moving less than 10 mph (16 km/h), delay times will be doubled. Windshield washer operation to use the washer, push on the end of the lever (toward the steering wheel) and hold while spray is desired. If the lever is pushed while in the intermittent setting, the wipers will t...

  • Page 160

    Warning! Sudden loss of visibility through the windshield could lead to a collision. You might not see other vehicles or other obstacles. To avoid sudden icing of the windshield during freezing weather, warm the windshield with the defroster before and during windshield washer use. Mist use the mist...

  • Page 161

    Rain sensing wipers — if equipped this feature senses moisture on the windshield and automatically activates the wipers for the driver. The feature is especially useful for road splash or overspray from the windshield washers of the vehicle ahead. Rotate the end of the multifunction lever to one of ...

  • Page 162

    Operate until the wiper switch is moved, vehicle speed is greater than 0 mph (0 km/h), or the outside tem- perature is greater than 32°f (0°c). • transmission in neutral position — when the ignition is on, and the transmission is in the neu- tral position, the rain sensing system will not operate un...

  • Page 163

    Warning! Do not adjust the steering column while driving. Adjusting the steering column while driving or driv- ing with the steering column unlocked, could cause the driver to lose control of the vehicle. Be sure the steering column is locked before driving your ve- hicle. Failure to follow this war...

  • Page 164

    Note: for vehicles equipped with driver memory seat, you can use your remote keyless entry (rke) transmitter or the memory switch on the driver’s door trim panel to return the tilt/telescopic steering column to pre-programmed positions. Refer to “driver memory seat” in this section for further infor...

  • Page 165

    Vehicles equipped with remote start on models that are equipped with remote start, the heated steering wheel and seat can be programmed to come on during a remote start. Refer to “remote starting system — if equipped” in “things to know before starting your vehicle” for further information. Warning!...

  • Page 166

    The electronic speed control buttons are located on the right side of the steering wheel. Note: in order to ensure proper operation, the elec- tronic speed control system has been designed to shut down if multiple speed control functions are operated at the same time. If this occurs, the electronic ...

  • Page 167

    System can be reactivated by pushing the electronic speed control on/off button and resetting the desired vehicle set speed. To activate push the on/off button. The cruise indicator light in the instrument cluster will illuminate. To turn the system off, push the on/off button a second time. The cru...

  • Page 168

    To vary the speed setting when the electronic speed control is set, you can in- crease speed by pushing the res (+) button. If the button is continually pressed, the set speed will continue to increase until the button is released, then the new set speed will be established. Pressing the res (+) but...

  • Page 169

    Warning! Electronic speed control can be dangerous where the system cannot maintain a constant speed. Your ve- hicle could go too fast for the conditions, and you could lose control and have an accident. Do not use electronic speed control in heavy traffic or on roads that are winding, icy, snow-cov...

  • Page 170

    Warning! • adaptive cruise control (acc) is a convenience system. It is not a substitute for active driving involvement. It is always the driver’s responsibil- ity to be attentive of road, traffic, and weather conditions, vehicle speed, distance to the vehicle ahead; and, most importantly, brake ope...

  • Page 171

    Warning! You should switch off the acc system: • when driving in fog, heavy rain, heavy snow, sleet, heavy traffic, and complex driving situations (i.E., in highway construction zones). • when entering a turn lane or highway off ramp; when driving on roads that are winding, icy, snow-covered, slippe...

  • Page 172

    Adaptive cruise control (acc) operation the speed control buttons (located on the right side of the steering wheel) operates the acc system. Note: any chassis/suspension modifications to the vehicle will effect the performance of the adaptive cruise control. Activating adaptive cruise control (acc) ...

  • Page 173

    Note: you cannot enable acc under the following conditions: • when in four-wheel drive low. • when you apply the brakes. • when the parking brake is set. • when the automatic transmission is in park, re- verse or neutral. • when pushing the res + button without a previously set speed in memory. To a...

  • Page 174

    Warning! Leaving the adaptive cruise control (acc) system on when not in use is dangerous. You could acciden- tally set the system or cause it to go faster than you want. You could lose control and have a collision. Always leave the system off when you are not using it. To set a desired acc speed wh...

  • Page 175

    • the system will not be controlling the distance be- tween your vehicle and the vehicle ahead. The vehicle speed will only be determined by the position of the accelerator pedal. To cancel the system will disable acc without erasing the memory if: • you softly tap the brake pedal. • you depress the...

  • Page 176

    Note: if acc is resumed or set with the esc/tcs off, esc will automatically be re-engaged. To turn off the system will turn off and erase the set speed in memory if: • you push the on/off button. • you turn off the ignition. • you switch to four-wheel drive low. To resume speed press the res + butto...

  • Page 177

    To vary the speed setting while acc is set, you can increase the set speed by pressing and holding the res + button. If the button is continually pressed, the set speed will continue to in- crease in 5 mph (8 km/h) increments until the button is released. The increase in set speed is reflected in th...

  • Page 178

    Setting the following distance in acc the specified following distance for acc can be set by varying the distance setting between 3 (long), 2 (me- dium), and 1 (short). Using this distance setting and the vehicle speed, acc calculates and sets the distance to the vehicle ahead. This distance setting...

  • Page 179

    To change the distance setting, press the distance button and release. Each time the button is pressed, the distance setting adjusts between long, medium, and short. If there is no vehicle ahead, the vehicle will maintain the set speed. If a slower moving vehicle is detected in the same lane, the ev...

  • Page 180

    • the system disengages. (refer to the information on acc activation). The maximum braking applied by acc is limited; how- ever, the driver can always apply the brakes manually, if necessary. Note: the brake lights will illuminate whenever the acc system applies the brakes. A proximity warning will ...

  • Page 181

    Press the menu button (located on the steer- ing wheel) repeatedly until one of the follow- ing displays in the evic: adaptive cruise control off − when acc is deactivated, the display will read “adaptive cruise control off.” adaptive cruise control ready − when acc is activated but the vehicle spee...

  • Page 182

    The acc screen will display once again if any acc activity occurs, which may include any of the following: • set speed change • distance setting change • system cancel • driver override • system off • acc proximity warning • acc unavailable warning the evic will return to the last display selected a...

  • Page 183

    Note: if the acc “clean radar sensor in front of vehicle” warning is active normal (fixed speed) cruise control is still available. For additional information refer to “normal (fixed speed) cruise control mode” in this section. If weather conditions are not a factor, the driver should examine the se...

  • Page 184

    • do not attach or install any accessories near the sensor, including transparent material or aftermarket grilles. Doing so could cause an acc system failure or malfunction. When the condition that deactivated the system is no longer present, the system will return to the “adaptive cruise control of...

  • Page 185

    Note: do not change the adjustment fasteners or pull the sensor off of the bracket. Doing so may misalign the sensor. Store the sensor and bracket assembly in a safe location. The wiring and connector must be stowed properly after the sensor and bracket assembly is removed. A connector plug is stowe...

  • Page 186

    Service acc warning if the system turns off, and the evic displays “acc/ fcw unavailable service radar sensor”, it indicates there is an internal system fault. Although the vehicle is still drivable under normal conditions, have the system checked by an authorized dealer. Precautions while driving w...

  • Page 187

    Offset driving acc may not detect a vehicle in the same lane that is offset from your direct line of travel. There will not be sufficient distance to the vehicle ahead. The offset vehicle may move in and out of the line of travel, which can cause your vehicle to brake or accelerate unexpectedly. Tur...

  • Page 188

    Using acc on hills when driving on hills, acc may not detect a vehicle in your lane. Depending on the speed, vehicle load, traffic conditions, and the steepness of the hills, acc perfor- mance may be limited. Lane changing acc will not detect a vehicle until it is completely in the lane in which you...

  • Page 189

    Narrow vehicles some narrow vehicles traveling near the outer edges of the lane or edging into the lane are not detected until they have moved fully into the lane. There will not be suffi- cient distance to the vehicle ahead. 3 understanding the features of your vehicle 187.

  • Page 190

    Stationary objects and vehicles acc does not react to stationary objects and stationary vehicles. For example, acc will not react in situations where the vehicle you are following exits your lane and the vehicle ahead is stopped in your lane. Always be attentive and ready to apply the brakes if nece...

  • Page 191

    Displayed if the system was in the acc off position. To switch back to adaptive cruise control mode, press the mode button a second time. Warning! In the normal cruise control mode, the system will not react to vehicles ahead. In addition, the proximity warning does not activate and no alarm will so...

  • Page 192

    • the electronic stability control/traction control sys- tem (esc/tcs) activates. To resume press the res + button and then remove your foot from the accelerator pedal. The evic will display the last set speed. To turn off the system will turn off and erase the set speed in memory if: • you push the...

  • Page 193

    Note: the minimum speed for fcw activation is 10 mph (16 km/h). Warning! Forward collision warning (fcw) is not intended to avoid a collision on its own, nor can fcw detect every type of collision. The driver has the responsi- bility to avoid a collision by controlling the vehicle via braking and st...

  • Page 194

    The default status of fcw is the “far” setting, this allows the system to warn you of a possible collision with the vehicle in front of you when you are farther away. This gives you the most reaction time. Changing the fcw status to the “near” setting, allows the system to warn you of a possible col...

  • Page 195

    Changing the fcw status to “off” prevents the system from warning you of a possible collision with the vehicle in front of you. Note: in the “off” setting fcw off will be displayed in the evic. Note: • the system will retain the last setting selected by the driver after ignition shut down. Example o...

  • Page 196

    • fcw will not react to irrelevant objects such as over- head objects, ground reflections, objects not in the path of the car, stationary objects that are far away, oncom- ing traffic, or leading vehicles with the same or higher rate of speed. • fcw will be disabled like acc below with the un- avail...

  • Page 197

    Parksense 姞 rear park assist — if equipped the parksense 威 rear park assist system provides visual and audible indications of the distance between the rear fascia and a detected obstacle when backing up, e.G. During a parking maneuver. Refer to parksense 威 system usage precautions for limitations of...

  • Page 198

    The parksense 威 warning display is located in the instru- ment cluster’s evic display. It provides both visual and audible warnings to indicate the distance between the rear fascia/bumper and the detected obstacle. Parksense 姞 display when the vehicle is in reverse, the warning display will turn on ...

  • Page 199

    The system will indicate a detected obstacle by showing three solid arcs and will produce a one-half second tone. As the vehicle moves closer to the object the evic display will show fewer arcs and the sound tone will change from slow, to fast, to continuous. Park assist off slow tone 3 understandin...

  • Page 200

    The vehicle is close to the obstacle when the evic display shows one flashing arc and sounds a continuous tone. The following chart shows the warning alert operation when the system is detecting an obstacle: fast tone continuous tone 198 understanding the features of your vehicle.

  • Page 201

    Warning alerts rear distance (in/cm) greater than 79 in (200 cm) 79-39 in (200-100 cm) 39-25 in (100-65 cm) 25-12 in (65-30 cm) less than 12 in (30 cm) audible alert chime none single 1/2 second tone slow fast continuous display message park assist on warning object detected warning object detected ...

  • Page 202

    Enabling and disabling parksense 姞 parksense 威 can be enabled and disabled with a switch located in the switch bank of the instrument panel or through the customer-programmable features section of the evic. The available choices are: off, sound only, or sound and display. Refer to “electronic vehicl...

  • Page 203

    Detected a faulted condition, the evic will display the “clean park assist sensors” or the “service park assist system” message for as long as the vehicle is in reverse. Under this condition, parksense 威 will not operate. If “clean park assist sensors” appears in the electronic vehicle information c...

  • Page 204

    • clean the parksense威 sensors regularly, taking care not to scratch or damage them. The sensors must not be covered with ice, snow, slush, mud, dirt or debris. Failure to do so can result in the system not working properly. The parksense 威 system might not detect an obstacle behind the fascia/bumpe...

  • Page 205

    Warning! • drivers must be careful when backing up even when using the parksense 威 rear park assist sys- tem. Always check carefully behind your vehicle, look behind you, and be sure to check for pedes- trians, animals, other vehicles, obstructions, and blind spots before backing up. You are respons...

  • Page 206

    Parkview 姞 rear back up camera — if equipped your vehicle may be equipped with the parkview 威 rear back up camera that allows you to see an on-screen image of the rear surroundings of your vehicle whenever the shift lever is put into reverse. The image will be displayed on the navigation/multimedia ...

  • Page 207

    Warning! Drivers must be careful when backing up even when using the parkview 威 rear back up camera. Always check carefully behind your vehicle, and be sure to check for pedestrians, animals, other vehicles, ob- structions, or blind spots before backing up. You are responsible for the safety of your...

  • Page 208

    4. Enable or disable the rear camera feature by selecting the “enable rear camera in reverse” soft key and pressing the “save” soft-key. Turning parkview 姞 on or off — without navigation/multimedia radio 1. Press the “menu” hard-key. 2. Select “system setup” soft-key. 3. Enable or disable the rear c...

  • Page 209

    To turn the lights off, press the switch a second time. The lights also turn on when a door is opened. The lights will also turn on when the unlock button on the rke is pressed. Sunglass bin door at the front of the console a compartment is provided for the storage of a pair of sunglasses. The stora...

  • Page 210

    Garage door opener — if equipped homelink 威 replaces up to three remote controls (hand- held transmitters) that operate devices such as garage door openers, motorized gates, lighting or home security systems. The homelink 威 unit operates off your vehicle’s battery. The homelink 威 buttons that are lo...

  • Page 211

    Warning! • your motorized door or gate will open and close while you are training the universal transceiver. Do not train the transceiver if people, pets or other objects are in the path of the door or gate. Only use this transceiver with a garage door opener that has a “stop and reverse” feature as...

  • Page 212

    Place the handheld transmitter 1 to 3 in (3 to 8 cm) away from the homelink 威 button you wish to program while keeping the indicator light in view. 3. Simultaneously press and hold both the chosen homelink 威 button and the handheld transmitter button until the homelink 威 indicator changes from a slo...

  • Page 213

    This can usually be found where the hanging antenna wire is attached to the garage door opener motor. It is not the button normally used to open and close the door. 1. Firmly press and release the learn or training button. The name and color of the button may vary by manufacturer. Note: you have 30 ...

  • Page 214

    Gate operator/canadian programming canadian radio frequency laws require transmitter sig- nals to time-out (or quit) after several seconds of trans- mission – which may not be long enough for homelink 威 to pick up the signal during programming. Similar to this canadian law, some u.S. Gate operators ...

  • Page 215

    Reprogramming a single homelink 姞 button to reprogram a channel that has been previously trained, follow these steps: 1. Turn the ignition switch to the on/run position. 2. Press and hold the desired homelink 威 button until the indicator light begins to flash after 20 seconds. Do not release the but...

  • Page 216

    General information this device complies with fcc rules part 15 and industry canada rss-210. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference that may be received including interference that may cause...

  • Page 217

    Warning! • never leave children in a vehicle with the key in the ignition switch. Occupants, particularly unat- tended children, can become entrapped by the power sunroof while operating the power sunroof switch. Such entrapment may result in serious injury or death. • in a collision, there is a gre...

  • Page 218

    Note: if three consecutive sunroof close attempts re- sult in pinch protect reversals, the fourth close attempt will be a manual close movement with pinch protect disabled. Pinch protect override if a known obstruction (ice, debris, etc.) prevents closing the sunroof, press the switch forward and ho...

  • Page 219

    Sunroof maintenance use only a nonabrasive cleaner and a soft cloth to clean the glass panel. Ignition off operation the power sunroof switches remain active for up ap- proximately ten minutes after the ignition switch has been turned off. Opening either front door will cancel this feature. Command ...

  • Page 220

    Warning! • never leave children in a vehicle with the key in the ignition switch. Occupants, particularly unat- tended children, can become entrapped by the power sunroof while operating the power sunroof switch. Such entrapment may result in serious injury or death. • in a collision, there is a gre...

  • Page 221

    The vent switch is pressed, the shade will automatically move to the middle position before the sunroof begins express vent operation. Closing sunroof – express press the sunroof switch forward for less than one second and release, and the sunroof glass will automatically close from any position, th...

  • Page 222

    Sunroof and power shade movement – manual if any sunroof or shade switch is pressed and held for more than one second, the sunroof or shade movement will continue only as long as the switch is continuously held. Whenever the switch is released, any sunroof or shade movement will stop. This allows th...

  • Page 223

    Wind buffeting wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions. This is a normal occur- rence and ...

  • Page 224

    Power outlets labeled with a “key” are powered when the ignition switch is in the on or acc position, while the outlets labeled with a “battery” are connected directly to the battery and powered at all times. Note: • all accessories connected to the “battery” powered outlets should be removed or tur...

  • Page 225

    The rear power outlet is located in the right rear cargo area. Center console outlet rear power outlet 3 understanding the features of your vehicle 223.

  • Page 226

    Warning! To avoid serious injury or death: • only devices designed for use in this type of outlet should be inserted into any 12 volt outlet. • do not touch with wet hands. • close the lid when not in use and while driving the vehicle. • if this outlet is mishandled, it may cause an electric shock a...

  • Page 227

    Caution! • many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.E., cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting. • ac...

  • Page 228

    Power inverter — if equipped there is a 115 volt, 150 watt inverter outlet located on the back of the center console to convert dc current to ac current. This outlet can power cellular phones, electron- ics and other low power devices requiring power up to 150 watts. Certain high-end video games, su...

  • Page 229

    May have to be reset manually. To reset the inverter manually press the power inverter button off and on. To avoid overloading the circuit, check the power ratings on electrical devices prior to using the inverter. The power inverter switch is located on the switch bank below the climate controls. T...

  • Page 230

    Cupholders there are two cupholders for the front seat passengers located in the center console. There are two cupholders for the rear seat passengers located in the fold-down center armrest. Front cupholder location rear cupholders 228 understanding the features of your vehicle.

  • Page 231

    Storage glove compartment the glove compartment is located on the right side of the instrument panel. To open the glove compartment, pull outward on the latch and lower the glove box door. Glove compartment opened glove compartment 3 understanding the features of your vehicle 229.

  • Page 232

    Door storage large storage areas are built into the door panels for easy access. Center console the center console contains both an upper and a lower storage area. Door panel storage storage compartment 230 understanding the features of your vehicle.

  • Page 233

    To open the upper storage compartment, pull upward on the small latch located on the lid. Lift upward on the larger of the latches to access the lower storage compartment. Cargo area features rechargeable flashlight the rechargeable flashlight is mounted on the left side of the cargo area. The flash...

  • Page 234

    Bulbs and is powered by rechargeable lithium batteries that recharge when snapped back into place. Press in on the flashlight to release it. To operate the flashlight, press the switch once for high, twice for low, and a third time to return to off. Press and release three-press switch 232 understan...

  • Page 235

    Cargo storage bins there are four removable storage bins located in the rear cargo area. There are two storage bins located on either side of the cargo area. Two additional storage bins are located under the load floor. To access the lower storage bins, raise the load floor and attach the tether hoo...

  • Page 236

    Retractable cargo area cover — if equipped note: the purpose of this cover is for privacy, not to secure loads. It will not prevent cargo from shifting or protect passengers from loose cargo. To cover the cargo area: 1. Grasp the cover at the center handle. Pull it over the cargo area. 2. Insert the...

  • Page 237

    Warning! In a collision, a loose cargo cover in the vehicle could cause injury. It could fly around in a sudden stop and strike someone in the vehicle. Do not store the cargo cover on the cargo floor or in the passenger compart- ment. Remove the cover from the vehicle when taken from its mounting. D...

  • Page 238

    Cargo tie-down hooks the cargo tie-downs, located on the cargo area floor, should be used to safely secure loads when the vehicle is moving. Warning! • to help protect against personal injury, passengers should not be seated in the rear cargo area. The rear cargo space is intended for load carrying ...

  • Page 239

    Warning! (continued) • do not carry loads which exceed the load limits described on the label attached to the left door or left door center pillar. • always place cargo evenly on the cargo floor. Put heavier objects as low and as far forward as possible. • place as much cargo as possible in front of...

  • Page 240

    Rotate the center portion of the lever upward to the first detent for intermittent operation and to the second detent for continuous rear wiper operation. Rotating the center portion upward once more will activate the washer pump which will continue to operate as long as the switch is held. Upon rel...

  • Page 241

    Note: to prevent excessive battery drain, use the rear window defroster only when the engine is operating. Caution! Failure to follow these cautions can cause damage to the heating elements: • use care when washing the inside of the rear window. Do not use abrasive window cleaners on the interior su...

  • Page 242

    To move the crossbars, loosen the attachments, located at the upper edge of each crossbar, approximately eight turns using the anti-theft wrench provided with the mopar 威 crossbars. Then, move the crossbar to the desired position, keeping the crossbars parallel to the rack frame. Once the crossbar i...

  • Page 243

    Caution! • to prevent damage to the roof of your vehicle, do not carry any loads on the roof rack without the crossbars installed. The load should be secured and placed on top of the crossbars, not directly on the roof. If it is necessary to place the load on the roof, place a blanket or some other ...

  • Page 245: Contents

    Understanding your instrument panel contents 䡵 instrument panel features . . . . . . . . . . . . . . . 246 䡵 instrument cluster . . . . . . . . . . . . . . . . . . . . 247 䡵 instrument cluster descriptions . . . . . . . . . . . 248 䡵 electronic vehicle information center (evic) . . 258 ▫ electronic ...

  • Page 246

    ▫ compass / temperature display . . . . . . . . . 277 ▫ customer-programmable features (system setup) . . . . . . . . . . . . . . . . . . . . . . 280 䡵 media center 730n/430/430n (rhr/rer/ rbz/rhb) cd/dvd/hdd/nav — if equipped . . . . . . . . . . . . . . . . . . . . . . . . . . 288 ▫ operating instr...

  • Page 247

    䡵 ipod威/usb/mp3 control — if equipped . . . . . 313 ▫ connecting the ipod威 or external usb device . . . . . . . . . . . . . . . . . . . . . . . . . . . . 314 ▫ using this feature . . . . . . . . . . . . . . . . . . . 314 ▫ controlling the ipod威 or external usb device using radio buttons . . . . . . ...

  • Page 248

    Instrument panel features 1 — air outlet 6 — lower switch bank 11 — hood release 2 — instrument cluster 7 — hazard switch 12 — fuel door release 3 — radio 8 — storage bin 13 — headlight switch 4 — glove compartment 9 — esc button 14 – dimmer control 5 — climate controls 10 — ignition switch 246 unde...

  • Page 249

    Instrument cluster 4 understanding your instrument panel 247.

  • Page 250

    Instrument cluster descriptions 1. Tachometer indicates the engine speed in revolutions per minute (rpm x 1000). 2. Airbag warning light this light will turn on for four to eight seconds as a bulb check when the ignition switch is first turned to the on/run position. If the light is either not on du...

  • Page 251

    Warning! A malfunctioning catalytic converter, as referenced above, can reach higher temperatures than in normal operating conditions. This can cause a fire if you drive slowly or park over flammable substances such as dry plants or wood or cardboard, etc. This could result in death or serious injur...

  • Page 252

    5. Tow/haul indicator light — if equipped this light will illuminate when the tow/ haul button has been selected. The tow/ haul button is located in the center of the instrument panel (below the climate controls). 6. Turn signal indicator the arrows will flash with the exterior turn signals when the...

  • Page 253

    As it was before the repair or service. If s/he cannot do so, then the odometer must be set at zero, and a sticker must be placed in the door jamb stating what the mileage was before the repair or service. It is a good idea for you to make a record of the odometer reading before the repair/ service,...

  • Page 254

    Please note that the tpms is not a substitute for proper tire maintenance, and it is the driver’s responsibility to maintain correct tire pressure, even if under-inflation has not reached the level to trigger illumination of the tpms low tire pressure telltale. Your vehicle has also been equipped wi...

  • Page 255

    12. Position light indicator — if equipped this indicator will illuminate when the park lights or headlights are turned on. 13. Seat belt reminder light when the ignition switch is first turned to the on/run position, this light will turn on for four to eight seconds as a bulb check. During the bulb...

  • Page 256

    The dual brake system provides a reserve braking capac- ity in the event of a failure to a portion of the hydraulic system. A leak in either half of the dual brake system is indicated by the brake warning light, which will turn on when the brake fluid level in the master cylinder has dropped below a...

  • Page 257

    The light also will turn on when the parking brake is applied with the ignition switch in the on/run posi- tion. Note: this light shows only that the parking brake is applied. It does not show the degree of brake application. 15. Anti-lock brake (abs) light this light monitors the anti-lock brake sy...

  • Page 258

    18. Fuel door reminder the fuel pump symbol points to the side of the vehicle where the fuel door is located. 19. Fuel gauge the pointer shows the level of fuel in the fuel tank when the ignition switch is in the on/run position. 20. Electronic vehicle information center (evic) white telltale area t...

  • Page 259

    25. Temperature gauge the temperature gauge shows engine coolant tempera- ture. Any reading within the normal range indicates that the engine cooling system is operating satisfactorily. The gauge pointer will likely indicate a higher tempera- ture when driving in hot weather, up mountain grades, or ...

  • Page 260

    Electronic vehicle information center (evic) the electronic vehicle information center (evic) fea- tures a driver-interactive display that is located in the instrument cluster. The evic consists of the following: • system status • vehicle information warning message displays • personal settings (cus...

  • Page 261

    The system allows the driver to select information by pressing the following buttons mounted on the steering wheel: up button press and release the up button to scroll up- ward through the main menus (fuel economy, vehicle info, tire psi, cruise, messages, units, system setup) and sub menus. Down bu...

  • Page 262

    Back button press the back button to scroll back to a previous menu or sub menu. Electronic vehicle information center (evic) displays when the appropriate conditions exist, the evic displays the following messages: • service tire pressure system • service park assist system • park assist system bli...

  • Page 263

    • adaptive cruise off — when the adaptive cruise control (acc) system is turned off. Refer to “adap- tive cruise control (acc)” in “understanding the features of your vehicle” (if equipped). • acc ready — when the acc system is activated. Refer to “adaptive cruise control (acc)” in “under- standing ...

  • Page 264

    • clean radar sensor in the front of vehicle — if the acc system deactivates due to performance limiting conditions. Refer to “adaptive cruise control (acc)” in “understanding the features of your vehicle” (if equipped). • acc/fcw unavailable vehicle system error — if the acc system turns off due to...

  • Page 265

    • remote start disabled — system fault • remote start disabled — turn key • remote start active — key to run • memory 1 profile set • memory 2 profile set • memory system unavailable — not in park • memory system unavailable — seatbelt buckled • memory 1 profile recall • memory 2 profile recall • pr...

  • Page 266

    • sport not available in 4 low 4 high is required • rock not available in 4 low 4 high is required • to tow vehicle safely, read neutral shift procedure in owners manual • for 4x4 low slow below 5 mph or 8 kph put trans in n press 4 low • for 4x4 high slow below 5 mph or 8 kph put trans in n press 4...

  • Page 267

    • service air suspension system — this is displayed when a fault has occurred in the system. The system will have limited operation at that point. • immediate air suspension service/repair required — this is displayed when a fault has occurred in the system which results in a complete system shutdow...

  • Page 268

    Evic white telltale lights this area will show reconfigurable white caution tell- tales. These telltales include: • shift lever status the shift lever status “p,r,n,d,l,5,4,3,2,1” are displayed indicating the shift lever position. Telltales “5,4,3,2,1” indicate the electronic range select (ers) feat...

  • Page 269

    • power steering system over temperature — if equipped if the “power steering system over temp” message and a icon are displayed on the evic screen, it indicates that extreme steer- ing maneuvers may have occurred, which caused an over temperature condition in the power steering system. You will los...

  • Page 270

    • air suspension up the air suspension up telltale will illuminate when the air suspension is in use. For further information, refer to “starting and operating”. • air suspension down the air suspension down telltale will illumi- nate when the air suspension is in use. For further information, refer...

  • Page 271

    Evic red telltale lights this area will show reconfigurable red telltales. These telltales include: • door ajar this light will turn on to indicate that one or more door may be ajar. • liftgate ajar this light will turn on to indicate that liftgate may be ajar. • liftgate flipper glass ajar this lig...

  • Page 272

    Vehicle is experiencing a problem with the charging system. Obtain service immediately. See an autho- rized dealer. If jump starting is required, refer to “jump starting procedures” in “what to do in emergencies”. • electronic throttle control (etc) light this light informs you of a problem with the...

  • Page 273

    If the light turns on while driving, safely pull over and stop the vehicle. If the a/c system is on, turn it off. Also, shift the transmission into neutral and idle the ve- hicle. If the temperature reading does not return to normal, turn the engine off immediately and call for service. Refer to “if...

  • Page 274

    Engine oil change indicator system oil change due your vehicle is equipped with an engine oil change indicator system. The “oil change due” message will flash in the evic display for approximately 10 seconds after a single chime has sounded, to indicate the next scheduled oil change interval. The en...

  • Page 275

    Press the up/down buttons to cycle through all the trip computer functions. The trip functions mode displays the following informa- tion: average fuel economy / fuel saver mode — if equipped shows the average fuel economy since the last reset. When the fuel economy is reset, the display will read “r...

  • Page 276

    Determined by a weighted average of the instantaneous and average fuel economy, according to the current fuel tank level. Dte cannot be reset through the select button. Note: significant changes in driving style or vehicle loading will greatly affect the actual drivable distance of the vehicle, rega...

  • Page 277

    Press the up/down buttons to cycle through all the trip computer functions. The trip functions mode displays the following informa- tion: trip a shows the total distance traveled for trip a since the last reset. Trip b shows the total distance traveled for trip b since the last reset. Elapsed time s...

  • Page 278

    Vehicle info (customer information features) press and release the up or down button until “vehicle info” displays in the evic and press the select button. Press the up and down button to scroll through the available information displays, then press select to display anyone of the following choices....

  • Page 279

    Note: • tires heat up during normal driving conditions. Heat will cause the tire pressure to increase from 2 to 6 psi (14 to 41 kpa) during normal driving conditions. Refer to “tires-general information/tire inflation pressures” in “starting and operating” for additional informa- tion. • your system...

  • Page 280

    Note: the system will display the last known outside temperature when starting the vehicle and may need to be driven several minutes before the updated tempera- ture is displayed. Engine temperature can also affect the displayed temperature, therefore temperature readings are not updated when the ve...

  • Page 281

    5. Complete one or more 360–degree turns (in an area free from large metal or metallic objects) until the “cal” indicator turns off. The compass will now function normally. Compass variance compass variance is the difference between magnetic north and geographic north. To compensate for the differen...

  • Page 282

    3. Press the down button until the “compass variance” message is displayed in the evic, then press the select button. The last variance zone number displays in the evic. 4. Press and release the select button until the proper variance zone is selected, according to the map. 5. Press and release the ...

  • Page 283

    Auto lock doors when this feature is selected, all doors will lock auto- matically when the vehicle reaches a speed of 15 mph (24 km/h). To make your selection, press and release the select button until a check-mark appears next to the feature showing the system has been activated, or the check-mark...

  • Page 284

    Grasped. With passive entry, if driver door 1st press is programmed touching the handle more than once will only result in the driver’s door opening. If driver door first is selected, once the driver door is opened, the interior door lock/unlock switch can be used to unlock all doors (or use rke tra...

  • Page 285

    This feature may be selected with or without the “flash lamps with lock” feature. To make your selection, press and release the select button until a check-mark ap- pears next to the feature showing the system has been activated or the check-mark is removed, showing the system has been deactivated. ...

  • Page 286

    The headlights will also turn off when the wipers are turned off if they were turned on by this feature. To make your selection, press and release the select button until a check-mark appears next to the feature showing the system has been activated or the check-mark is removed, showing the system h...

  • Page 287

    Key-off power delay when this feature is selected, the power window switches, radio, hands-free system (if equipped), dvd video system (if equipped), power sunroof (if equipped), and power outlets will remain active for up to 10 minutes after the ignition switch is turned off. Opening either front v...

  • Page 288

    Make your selection, press and release the select button until a check-mark appears next to the feature showing the system has been activated or the check-mark is removed, showing the system has been deactivated. Refer to “lights/smartbeam™ — if equipped” in “un- derstanding the features of your veh...

  • Page 289

    Alert in the outside mirrors as well as an audible alert when the turn signal is on. When “blind spot: off” is selected the blind spot monitor (bsm) system is deacti- vated. Note: if your vehicle has experienced any damage in the area where the sensor is located, even if the fascia is not damaged, t...

  • Page 290

    Compass variance refer to “compass display” for more information. Media center 730n/430/430n (rhr/rer/rbz/ rhb) cd/dvd/hdd/nav — if equipped note: the sales code is located on the lower right side of the unit’s faceplate. Refer to your uconnect™ multimedia rhr, rer, rbz or rhb user’s manual for deta...

  • Page 291

    Operating instructions — radio mode note: the ignition switch must be in the on or acc position to operate the radio. Power switch/volume control (rotary) push the on/volume control knob to turn on the radio. Push the on/volume control knob a second time to turn off the radio. Electronic volume cont...

  • Page 292

    4. Adjust the minutes using the right side tune/ scroll control knob. Press the tune/scroll control knob to save time change. 5. To exit, press any button/knob, or wait five seconds. Rw/ff pressing the rw (rewind) or ff (fast forward) buttons causes the tuner to search for the next frequency in the ...

  • Page 293

    Am/fm button press the buttons to select either am or fm mode. Set/rnd button — to set the pushbutton memory when you are receiving a station that you wish to commit to pushbutton memory, press the set/rnd button. The symbol set 1 will now show in the display window. Select the button (1 to 6) you w...

  • Page 294

    • this radio is capable of playing compact discs (cd), recordable compact discs (cd-r), rewritable compact discs (cd-rw), compact discs with mp3 tracks and multisession compact discs with cd and mp3 tracks. Inserting compact disc(s) gently insert one cd into the cd player with the cd label facing up...

  • Page 295

    If you have ejected a disc and have not removed it within 10 seconds, it will be reloaded. If the cd is not removed, the radio will reinsert the cd but will not play it. A disc can be ejected with the radio and ignition off. Note: ejecting with the ignition off is not allowed on convertible or soft-...

  • Page 296

    Notes on playing mp3 files the radio can play mp3 files; however, acceptable mp3 file recording media and formats are limited. When writing mp3 files, pay attention to the following restric- tions. Supported media (disc types) the mp3 file recording media supported by the radio are cdda, cd-r, cd-rw...

  • Page 297

    Discs created with an option such as ⬙keep disc open after writing ⬙ are most likely multisession discs. The use of multisession for cd audio or mp3 playback may result in longer disc loading times. Supported mp3 file formats the radio will recognize only files with the *.Mp3 exten- sion as mp3 file...

  • Page 298

    Playback of mp3 files when a medium containing mp3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the mp3 files. Loading times for playback of mp3 files may be affected by the following: • med...

  • Page 299

    Media center 130 with satellite radio (sales code res+rsc) note: the radio sales code is located on the lower right side of the radio faceplate. Operating instructions — radio mode note: the ignition switch must be in the on/run or acc position to operate the radio. Power switch/volume control (rota...

  • Page 300

    To seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection. Holding either button will bypass stations without stopping until you release it. Voice command system (radio) — if equipped refer to “voice command” in the uconnect™ user ma...

  • Page 301

    3. After adjusting the hours, press the right side tune/ scroll control knob to set the minutes. The minutes will begin to blink. 4. Adjust the minutes using the right side tune/ scroll control knob. Press the tune/scroll control knob to save time change. 5. To exit, press any button/knob or wait fi...

  • Page 302

    Push the rotary tune/scroll control knob a second time and mid will display. Turn the tune/scroll control knob to the right or left to increase or decrease the mid-range tones. Push the rotary tune/scroll control knob a third time and treble will display. Turn the tune/scroll control knob to the rig...

  • Page 303

    Program type 16-digit character display information inform jazz jazz news news nostalgia nostalga oldies oldies personality persnlty public public rhythm and blues r & b religious music rel musc religious talk rel talk rock rock soft soft soft rock soft rck soft rhythm and blues soft r&b sports spor...

  • Page 304

    Hours, press the tune/scroll control knob to set the minutes. The minutes will begin to blink. Adjust the minutes using the right side tune/scroll control knob. Press the tune/scroll control knob to save time change. Am/fm button press the button to select either am or fm mode. Set/rnd button — to s...

  • Page 305

    Operation instructions — cd mode for cd and mp3 audio play note: • the ignition switch must be in the on/run or acc position to operate the radio. • this radio is capable of playing compact discs (cd), recordable compact discs (cd-r), rewritable compact discs (cd-rw), compact discs with mp3 tracks a...

  • Page 306

    Eject button - ejecting a cd press the eject button to eject the cd. If you have ejected a disc and have not removed it within 10 seconds, it will be reloaded. If the cd is not removed, the radio will reinsert the cd but will not play it. A disc can be ejected with the radio and ignition off. Note: ...

  • Page 307

    Set/rnd button (random play button) press this button while the cd is playing to activate random play. This feature plays the selections on the compact disc in random order to provide an interesting change of pace. Press the right seek button to move to the next ran- domly selected track. Press the ...

  • Page 308

    • maximum number of characters in file/folder names: • level 1: 12 (including a separator ⬙.⬙ and a three- character extension) • level 2: 31 (including a separator ⬙.⬙ and a three- character extension) multisession disc formats are supported by the radio. Multisession discs may contain combinations...

  • Page 309

    Playlist files are not supported. Mp3 pro files are not supported. Playback of mp3 files when a medium containing mp3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the mp3 files. Loading time...

  • Page 310

    Press the info button once more to return to ⬙elapsed time ⬙ priority mode. Press and hold the info button for three seconds or more and the radio will display song titles for each file. Press and hold the info button again for three seconds to return to ⬙elapsed time⬙ display. Operation instruction...

  • Page 311

    System activation sirius satellite radio service is pre-activated, and you may begin listening immediately to the one year of audio service that is included with the factory-installed satellite radio system in your vehicle. Sirius will supply a wel- come kit that contains general information, includ...

  • Page 312

    Bikes should be placed as far rearward as possible, within the loading design of the rack. Do not place items directly on or above the antenna. Reception quality satellite reception may be interrupted due to one of the following reasons: • the vehicle is parked in an underground parking structure or...

  • Page 313

    Info button pressing the info button will cycle the display informa- tion between artist, song title, and composer (if avail- able). Also, pressing and holding the info button for an additional three seconds will make the radio display the song title all of the time (press and hold again to return t...

  • Page 314

    Setup button pressing the setup button allows you to select the following items: • display sirius id number — press the audio/ select button to display the sirius id number. This number is used to activate, deactivate, or change the sirius subscription. Set button – to set the pushbutton memory when...

  • Page 315

    Ipod 姞 /usb/mp3 control — if equipped note: this section is for sales code res and req/ rel/ret radios only with uconnect™. For sales code rbz/rhb, rhr, rhp, rhw or rb2 touch-screen radio ipod 威/usb/mp3 control feature, refer to the separate rbz/rhb, rhr, rhp, rhw or rb2 user’s manual. Ipod 威/usb/mp...

  • Page 316

    Connecting the ipod 姞 or external usb device use the connection cable to connect an ipod 威 or external usb device to the vehicle’s usb/aux connector port which is located in the center console or glove compart- ment. Once the audio device is connected and synchronized to the vehicle’s ipod 威/usb/mp3...

  • Page 317

    • the audio device can be controlled using the radio buttons to play, browse, and list the ipod 威 contents. • the audio device battery charges when plugged into the usb/aux connector (if supported by the specific audio device) controlling the ipod 姞 or external usb device using radio buttons to get ...

  • Page 318

    • jump forward in the current track by pressing and holding the ff >> button. • a single press backward rw or forward ff >> will jump backward or forward respectively, for five seconds. • use the seek and seek >> buttons to jump to the previous or next track. Pressing the seek >> button during play ...

  • Page 319

    List or browse mode during play mode, pressing any of the buttons described below, will bring up list mode. List mode enables scrolling through the list of menus and tracks on the audio device. • tune control knob: the tune control knob functions in a similar manner as the scroll wheel on the or ext...

  • Page 320

    • pressing a preset button will display the current list on the top line and the first item in that list on the second line. • to exit list mode without selecting a track, press the same preset button again to go back to play mode . • list button: the list button will display the top level menu of t...

  • Page 321

    Bluetooth streaming audio (btsa) music can be streamed from your cellular phone to the uconnect™ phone system. Controlling btsa using radio buttons to get into the btsa mode, press either “aux” button on the radio or press vr button and say “bluetooth stream- ing audio”. Play mode when switched to b...

  • Page 322

    Uconnect™ multimedia (sirius backseat tv™) — if equipped satellite video uses direct satellite receiver broadcasting technology to provide streaming video. The subscription service provider is sirius satellite radio. Uconnect™ studio (sirius backseat tv™) offers three video chan- nels for family ent...

  • Page 323

    Steering wheel audio controls the remote sound system controls are located on the rear surface of the steering wheel. Reach behind the wheel to access the switches. The right-hand control is a rocker-type switch with a pushbutton in the center and controls the volume and mode of the sound system. Pr...

  • Page 324

    Pressing the center button will make the radio switch between the various modes available (am/fm/sat/ cd/hdd/aux/ves, etc.). The left-hand control is a rocker-type switch with a pushbutton in the center. The function of the left-hand control is different depending on which mode you are in. The follo...

  • Page 325

    Cd/dvd disc maintenance to keep a cd/dvd in good condition, take the following precautions: 1. Handle the disc by its edge; avoid touching the surface. 2. If the disc is stained, clean the surface with a soft cloth, wiping from center to edge. 3. Do not apply paper or tape to the disc; avoid scratch...

  • Page 326

    Dual-zone manual heating and air conditioning the dual-zone manual climate controls allow both driver and front passenger seat occupants to select indi- vidual comfort settings. The controls consist of a series of outer rotary dials and inner push knobs. Blower control rotate this control to regulat...

  • Page 327

    • passenger temperature control rotate this control to regulate the tem- perature of the air inside the passenger compartment for the right front seat occupant. Rotating the dial left into the blue area of the scale indicates cooler temperatures while rotating right into the red area indicates warme...

  • Page 328

    Floor air is directed through the floor outlets with a small amount flowing through the defrost and side window demist outlets. Mix air is directed through the floor, defrost, and side window demist outlets. This setting works best in cold or snowy conditions that require extra heat to the windshiel...

  • Page 329

    Note: • continuous use of the recirculation mode may make the inside air stuffy and window fogging may occur. Extended use of this mode is not recommended. • the use of the recirculation mode in cold or damp weather could cause windows to fog on the inside, because of moisture buildup inside the veh...

  • Page 330

    Dual-zone automatic temperature control (atc) — if equipped • the automatic temperature control (atc) allows both driver and front passenger seat occupants to select individual comfort settings. • when occupants in the vehicle select an auto mode operation, auto blower operation is set by using a pu...

  • Page 331

    2. Recirculation control button press and release to change the current setting, the indicator illuminates when on. 3. Left front seat occupant temperature display this display shows the temperature setting for the left front seat occupant. 4. Mode display this display shows the current mode selecti...

  • Page 332

    11. Blower control there are seven blower speeds, the blower speed in- creases as you move the control to the right from the lowest blower setting. Performing this function will cause the atc to switch into manual mode. 12. Climate control off button press and release this button to turn the climate...

  • Page 333

    3. When the system is set up for your comfort level, it is not necessary to change the settings. You will experience the greatest efficiency by simply allowing the system to function automatically. Note: • it is not necessary to move the temperature settings for cold or hot vehicles. The system auto...

  • Page 334

    The blower fan speed can be set to any fixed speed by adjusting the blower control outer dial. The fan will now operate at a fixed speed until additional speeds are selected. This allows the front occupants to control the volume of air circulated in the vehicle and cancel the auto mode. The operator...

  • Page 335

    Defrost mode air comes from the windshield and side window demist outlets. Use defrost mode with maximum temperature settings for best windshield and side win- dow defrosting. When the defrost mode is selected, the blower will automatically default to medium-high unless the blower is controlled manu...

  • Page 336

    Note: in cold weather, use of recirculation mode may lead to excessive window fogging. The recirculation mode is not allowed in the floor/defrost mix and defrost modes to improve window clearing operation. Recirculation will be disabled automatically if these modes are selected. Operating tips windo...

  • Page 337

    Summer operation note: in some cases during high temperature trailer tow operation the air conditioning system performance may be reduced. This is to help protect the engine from overheating during the high load condition. Your air conditioning system is also equipped with an automatic recirculation...

  • Page 338

    Operating tips chart 336 understanding your instrument panel.

  • Page 339: Starting And Operating

    Starting and operating contents 䡵 starting procedures . . . . . . . . . . . . . . . . . . . . 343 ▫ automatic transmission . . . . . . . . . . . . . . . 343 ▫ keyless enter-n-go . . . . . . . . . . . . . . . . . . . 344 ▫ normal starting . . . . . . . . . . . . . . . . . . . . . 345 ▫ extreme cold w...

  • Page 340

    ▫ shift positions . . . . . . . . . . . . . . . . . . . . . . 359 ▫ shifting procedures . . . . . . . . . . . . . . . . . . . 360 ▫ quadra-drive威 ii system – if equipped . . . . 362 䡵 selec-terrain™ — if equipped . . . . . . . . . . . . 363 ▫ description . . . . . . . . . . . . . . . . . . . . . . ....

  • Page 341

    䡵 multi-displacement system (mds) (if equipped) — 5.7l engine only . . . . . . . . . . 379 䡵 parking brake . . . . . . . . . . . . . . . . . . . . . . . . 379 䡵 electronic brake control system . . . . . . . . . . . 381 ▫ anti-lock brake system (abs) . . . . . . . . . . . 381 ▫ traction control syste...

  • Page 342

    ▫ radial-ply tires . . . . . . . . . . . . . . . . . . . . . 406 ▫ spare tire matching original equipped tire and wheel – if equipped . . . . . . . . . . . . . . 406 ▫ compact spare tire – if equipped . . . . . . . . 407 ▫ full size spare – if equipped . . . . . . . . . . . . 408 ▫ limited-use spare...

  • Page 343

    ▫ carbon monoxide warnings . . . . . . . . . . . . 428 䡵 flexible fuel (3.6l engine only) — if equipped . . . . . . . . . . . . . . . . . . . . . . . . . . 429 ▫ e-85 general information . . . . . . . . . . . . . . . 429 ▫ ethanol fuel (e-85) . . . . . . . . . . . . . . . . . . . 430 ▫ fuel requirem...

  • Page 344

    䡵 snow plow . . . . . . . . . . . . . . . . . . . . . . . . . . 452 䡵 recreational towing (behind motorhome, etc.) . . . . . . . . . . . . . . . . 453 ▫ towing this vehicle behind another vehicle . . . . . . . . . . . . . . . . . . . . . 453 ▫ recreational towing — two-wheel drive models . . . . . ....

  • Page 345

    Starting procedures before starting your vehicle, adjust your seat, adjust the inside and outside mirrors, fasten your seat belt, and if present, instruct all other occupants to buckle their seat belts. Warning! Never leave children alone in a vehicle. Leaving unattended children in a vehicle is dan...

  • Page 346

    Do not press the accelerator. Use the fob with integrated key to briefly turn the ignition switch to the start position and release it as soon as the starter engages. The starter motor will continue to run, and it will disengage automatically when the engine is running. If the engine fails to start,...

  • Page 347

    Note: the engine start/stop button should only be removed or inserted with the ignition in the lock position (off position for keyless enter-n-go). Normal starting using the engine start/stop button note: normal starting of either a cold or a warm engine is obtained without pumping or pressing the a...

  • Page 348

    Note: if the ignition switch is left in the acc or run (engine not running) position and the transmission is in park, the system will automatically time out after 30 minutes of inactivity and the ignition will switch to the off position. Keyless enter-n-go functions – with driver’s foot off the brak...

  • Page 349

    If engine fails to start warning! • never pour fuel or other flammable liquids into the throttle body air inlet opening in an attempt to start the vehicle. This could result in a flash fire causing serious personal injury. • do not attempt to push or tow your vehicle to get it started. Vehicles equi...

  • Page 350

    Release it as soon as the starter engages. The starter motor will disengage automatically in 10 seconds. Once this occurs, release the accelerator pedal, turn the ignition switch to the lock position, wait 10 to 15 seconds, then repeat the “normal starting” procedure. Caution! To prevent damage to t...

  • Page 351

    Automatic transmission caution! Damage to the transmission may occur if the follow- ing precautions are not observed: • shift into park only after the vehicle has come to a complete stop. • shift into or out of reverse only after the vehicle has come to a complete stop and the engine is at idle spee...

  • Page 352

    Brake/transmission shift interlock system this vehicle is equipped with a brake transmission shift interlock system (btsi) that holds the shift lever in the park position when the ignition switch is in the lock position. To move the shift lever out of the park position, the ignition switch must be t...

  • Page 353

    Warning! • never use the park position as a substitute for the parking brake. Always apply the parking brake fully when parked to guard against vehicle movement and possible injury or damage. • it is dangerous to move the shift lever out of park or neutral if the engine speed is higher than idle spe...

  • Page 354

    Electronic range select (ers) operation the electronic range select (ers) shift control allows you to move the shift lever left (-) or right (+) when the shift lever is in the drive position, allowing you to limit the highest available gear. For example, if the driver shifts the transmission into er...

  • Page 355

    The ers designation for the current gear (the transmis- sion will not downshift). For example, if you are in drive and are in third (direct) gear, when you tap the shift lever one time to the left (-), the display will show 4 (ers 4 is direct gear). Another tap to the left (-) will shift the transmi...

  • Page 356

    • the engine coolant has reached normal operating tem- perature; • vehicle speed is above approximately 30 mph (48 km/h); • the tow/haul switch has not been activated; • transmission has reached normal operating temperature. Note: if the vehicle is started in extremely cold tem- peratures, the trans...

  • Page 357

    Operating in tow/haul mode, the transmission will shift into direct gear and overdrive will be enabled under steady cruise conditions. The “tow/haul indicator light” will illuminate in the instrument cluster to indicate when the switch has been activated. Pressing the switch a second time restores n...

  • Page 358

    To reset the transmission, use the following procedure: 1. Stop the vehicle. 2. Move the shift lever into the park position. 3. Turn the engine off, and be sure to turn the ignition switch to the lock position. 4. Wait approximately 10 seconds, then restart the en- gine. 5. Move the shift lever to t...

  • Page 359

    Gear) positions will demonstrate that the transmission is able to shift into and out of overdrive. For vehicles with 5.7l engines (which have two overdrive gears), the transmission may not shift into the top overdrive gear (normal fifth gear) until the transmission fluid and engine coolant are warm....

  • Page 360

    Quadra-trac ii 姞 operating instructions/ precautions – if equipped the quadra-trac ii 威 transfer case is fully automatic in the normal driving 4wd auto mode. The quadra-trac ii 威 transfer case provides three mode positions: • 4wd hi • neutral • 4wd low this transfer case is fully automatic in the 4w...

  • Page 361

    Proper operation of four-wheel drive vehicles depends on tires of equal size, type, and circumference on each wheel. Any difference will adversely affect shifting and cause damage to the transfer case. Because four-wheel drive provides improved traction, there is a tendency to exceed safe turning an...

  • Page 362

    4wd low this range is for low speed four-wheel drive. It locks the front and rear driveshafts together and forces the front and rear wheels to rotate at the same speed. It provides additional traction and maximum pulling power for loose, slippery road surfaces only. Do not exceed 25 mph (40 km/h). N...

  • Page 363

    4wd low to 4wd hi with the vehicle at speeds of 0 to 3 mph (0 to 5 km/h), the ignition switch in the on position or the engine running, shift the transmission into neutral, and press the “4wd low” button once on the transfer case switch. The “4wd low” indicator light in the instrument cluster will f...

  • Page 364

    The electronic vehicle information center (evic). Refer to “electronic vehicle information center (evic)” in “understanding your instrument panel” for further in- formation. 5. Repeat steps 1 to 4 to shift out of neutral. Note: if shift conditions/interlocks are not met, a “to tow vehicle safely, re...

  • Page 365

    Case and axle coupling differ in design, their operation is similar. Follow the quadra-trac ii 威 transfer case shifting information, preceding this section, for shifting this system. Selec-terrain™ — if equipped description selec-terrain™ combines the capabilities of the vehicle control systems, alo...

  • Page 366

    To allow more driver control of vehicle while maintain- ing safe handling controls. The vehicle will lower (if equipped with air suspension) to aero mode in high range. 4wd low is not available in sport mode, if 4wd low is selected the selec-terrain™ will auto- matically switch back to auto. • snow ...

  • Page 367

    Equipped with air suspension, the vehicle level will change to off-road 2. If the selec-terrain™ switch is in rock mode, and the transfer case is switched from 4wd low to 4wd high, the selec-terrain™ system will return to auto. Electronic vehicle information center (evic) display messages when the a...

  • Page 368

    • off-road 1 (or1) (raises the vehicle approximately 1.3 in (33 mm) – this position should be the default position for all off-road driving until or2 is needed. A smoother and more comfortable ride will result. Press the “up” button once from the nrh position while the vehicle speed is below 48 mph ...

  • Page 369

    • park mode (lowers the vehicle approximately 1.5 in (38 mm) – this position lowers the vehicle for easier passenger entry and exit as well as lowering the rear of the vehicle for easier loading and unloading of cargo. To enter park mode, press the “down” button once while the vehicle speed is below...

  • Page 370

    To assist with changing a spare tire, the quadra-lift™ air suspension system has a feature which allows the auto- matic leveling to be disabled. Press and hold both the “up” and “down” buttons simultaneously between 5 and 10 seconds, a message will appear in the evic stating leveling has been disabl...

  • Page 371

    Pressing the “up” button once will move the suspension one position higher from the current position, assuming all conditions are met (i.E. Engine running, speed below threshold, etc). The “up” button can be pressed multiple times, each press will raise the requested level by one position up to a ma...

  • Page 372

    (24 km/h) indicator lamp 4 will turn off and indicator lamp 3 will flash until park mode is achieved at which point indicator lamp 3 will go solid. If during the height change to park mode, the vehicle speed exceeds 15 mph (24 km/h), the height change will be paused until the vehicle speed either go...

  • Page 373

    Quadra-lift™ – if equipped when off-roading, it is recommended that the lowest useable vehicle height that will clear the current obstacle or terrain be selected. The vehicle height should then be raised as required by the changes in terrain. The selec-terrain™ switch will automatically change the v...

  • Page 374

    Driving through water although your vehicle is capable of driving through water, there are a number of precautions that must be considered before entering the water. Note: your vehicle is capable of water fording in up to 20 inches (51 cm) of water, while crossing small rivers or streams. To maintai...

  • Page 375

    Standing water avoid driving in standing water deeper than 20 inches (51 cm), and reduce speed appropriately to minimize wave effects. Maximum speed in 20 inches (51 cm) of water is less than 5 mph (8 km/h). Maintenance after driving through deep water, inspect your vehicle fluids and lubricants (en...

  • Page 376

    Regulate your speed. If the brakes are required to control vehicle speed, apply them lightly and avoid locking or skidding the tires. Warning! If the engine stalls, you lose forward motion, or cannot make it to the top of a steep hill or grade, never attempt to turn around. To do so may result in ti...

  • Page 377

    • completely inspect the underbody of your vehicle. Check tires, body structure, steering, suspension, and exhaust system for damage. • inspect the radiator for mud and debris and clean as required. • check threaded fasteners for looseness, particularly on the chassis, drivetrain components, steerin...

  • Page 378

    And increased ease of maneuverability in tight spaces. The system will vary its assist to provide light efforts while parking and good feel while driving. If the electro- hydraulic power steering system experiences a fault that prevents it from providing power steering assist, then the system will p...

  • Page 379

    • if the condition persists, see your authorized dealer for service. 5.7l engine the standard power steering system will give you good vehicle response and increased ease of maneuverability in tight spaces. The system will provide mechanical steering capability if power assist is lost. If for some r...

  • Page 380

    Power steering fluid check checking the power steering fluid level at a defined service interval is not required. The fluid should only be checked if a leak is suspected, abnormal noises are apparent, and/or the system is not functioning as antici- pated. Coordinate inspection efforts through an aut...

  • Page 381

    Multi-displacement system (mds) (if equipped) — 5.7l engine only this feature offers improved fuel economy by shutting off four of the engine’s eight cylinders during light load and cruise conditions. The system is automatic with no driver inputs or additional driving skills required. Note: the mds ...

  • Page 382

    Note: • when the parking brake is applied and the transmis- sion is placed in gear, the “brake warning light” will flash. If vehicle speed is detected, a chime will sound to alert the driver. Fully release the parking brake before attempting to move the vehicle. • this light only shows that the park...

  • Page 383

    Warning! (continued) • always fully apply the parking brake when leav- ing your vehicle, or it may roll and cause damage or injury. Also be certain to leave the transmission in park. Failure to do so may allow the vehicle to roll and cause damage or injury. Caution! If the “brake warning light” rema...

  • Page 384

    Warning! The abs cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions. The abs cannot prevent collisions, including those re- sulting from excessive speed in turns, driving on very slippery surfaces, or hydropl...

  • Page 385

    Benefit of the system, you must apply continuous brak- ing pressure during the stopping sequence (do not “pump” the brakes). Do not reduce brake pedal pressure unless braking is no longer desired. Once the brake pedal is released, the bas is deactivated. Warning! The bas cannot prevent the natural l...

  • Page 386

    Warning! Many factors, such as vehicle loading, road condi- tions and driving conditions, influence the chance that wheel lift or rollover may occur. Erm cannot prevent all wheel lift or rollovers, especially those that involve leaving the roadway or striking objects or other vehicles. The capabilit...

  • Page 387

    As little throttle as possible. Be sure to adapt your speed and driving to the prevailing road conditions. Warning! The electronic stability control (esc) cannot pre- vent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions....

  • Page 388

    To be used if the vehicle is in deep snow, sand, or gravel conditions and more wheel spin than esc would nor- mally allow is required to gain traction. To turn esc on again, momentarily press the “esc off” switch. This will restore the normal “esc on” mode of operation. Note: to improve the vehicle’...

  • Page 389

    Trailer sway control (tsc) tsc uses sensors in the vehicle to recognize an exces- sively swaying trailer and will take the appropriate actions to attempt to stop the sway. The system may reduce engine power and apply the brake of the appro- priate wheel(s) to counteract the sway of the trailer. Tsc ...

  • Page 390

    Hsa activation criteria the following criteria must be met in order for hsa to activate: • vehicle must be stopped. • vehicle must be on a 6% (approximate) grade or greater hill. • gear selection matches vehicle uphill direction (i.E., vehicle facing uphill is in forward gear; vehicle back- ing uphi...

  • Page 391

    Warning! • if you use a trailer brake controller with your trailer, your trailer brakes may be activated and deactivated with the brake switch. If so, when the brake pedal is released, there may not be enough brake pressure to hold the vehicle and trailer on a hill and this could cause a collision w...

  • Page 392

    Ready alert braking – if equipped ready alert braking may reduce the time required to reach full braking during emergency braking situations. It anticipates when an emergency braking situation may occur by monitoring how fast the throttle is released by the driver. When the throttle is released very...

  • Page 393

    When hdc is enabled, the hdc icon will be illuminated in the instrument cluster. Hdc will automatically apply the brakes to control downhill speed to the selected level when necessary on grades greater than approximately 8%. It will usually not activate on level ground. The hdc speed may be adjusted...

  • Page 394

    4wd low range set speeds • 1st = 1 mph (1.6 km/h) • 2nd = 2.5 mph (4 km/h) • 3rd = 4 mph (6 km/h) • 4th = 5.5 mph (9 km/h) • 5th or d (drive) = 7.5 mph (12 km/h) • reverse = 1 mph (1.6 km/h) • neutral = 2.5 mph (4 km/h) • park = hdc will not function hdc is intended for low speed off-road driving on...

  • Page 395

    Speeds greater than 30 mph (48 km/h), see your autho- rized dealer as soon as possible to have the problem diagnosed and corrected. The “esc activation/malfunction indicator light” (lo- cated in the instrument cluster) starts to flash as soon as the tires lose traction and the esc system becomes act...

  • Page 396

    Tire safety information tire markings note: • p (passenger) - metric tire sizing is based on u.S. Design standards. P-metric tires have the letter “p” molded into the sidewall preceding the size designa- tion. Example: p215/65r15 95h. • european-metric tire sizing is based on european design standar...

  • Page 397

    Tires designed to this standard have the letter “t” molded into the sidewall preceding the size designa- tion. Example: t145/80d18 103m. • high flotation tire sizing is based on u.S. Design standards and it begins with the tire diameter molded into the sidewall. Example: 31x10.5 r15 lt. Tire sizing ...

  • Page 398

    Example: service description: 95 = load index — a numerical code associated with the maximum load a tire can carry h = speed symbol — a symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions — the maximum speed corres...

  • Page 399

    Tire identification number (tin) the tin may be found on one or both sides of the tire, however, the date code may only be on one side. Tires with white sidewalls will have the full tin, including the date code, located on the white sidewall side of the tire. Look for the tin on the outboard side of...

  • Page 400

    Tire terminology and definitions term definition b-pillar the vehicle b-pillar is a structural member of the body located between the front and rear door (of a four-door vehicle) running from the sill to the roof. Cold tire pressure cold tire inflation pressure is defined as the tire pressure after ...

  • Page 401

    Tire loading and tire pressure tire placard location note: the proper cold tire inflation pressure is listed on the driver’s side b-pillar. Tire and loading information placard tire placard location tire and loading information placard 5 starting and operating 399.

  • Page 402

    This placard tells you important information about the: 1) number of people that can be carried in the vehicle 2) total weight your vehicle can carry 3) tire size designed for your vehicle 4) cold tire inflation pressures for the front, rear, and spare tires. Loading the vehicle maximum load on the ...

  • Page 403

    Steps for determining correct load limit 1. Locate the statement “the combined weight of occu- pants and cargo should never exceed xxx lbs or xxx kg” on your vehicle’s placard. 2. Determine the combined weight of the driver and passengers that will be riding in your vehicle. 3. Subtract the combined...

  • Page 404

    402 starting and operating.

  • Page 405

    Warning! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. Tires — general information tire pressure proper tire inflation pressur...

  • Page 406

    Warning! (continued) • unequal tire pressures from one side of the ve- hicle to the other can cause the vehicle to drift to the right or left. • always drive with each tire inflated to the recom- mended cold tire inflation pressure. Economy improper inflation pressures can cause uneven wear patterns...

  • Page 407

    Caution! After inspecting or adjusting the tire pressure, al- ways reinstall the valve stem cap. This will prevent moisture and dirt from entering the valve stem, which could damage it. Inflation pressures specified on the placard are always cold tire inflation pressure. Cold tire inflation pressure...

  • Page 408

    Tire pressures for high speed operation the manufacturer advocates driving at safe speeds within posted speed limits. Where speed limits or condi- tions are such that the vehicle can be driven at high speeds, maintaining correct tire inflation pressure is very important. Increased tire pressure and ...

  • Page 409

    Vehicle has an option for a spare tire matching original equipment tire and wheel, refer to the recommended tire rotation pattern in “tire rotation recommendations” in “starting and operating” for further information. If your vehicle is not equipped with an original equip- ment tire and wheel as a s...

  • Page 410

    Since this tire has limited tread life the original equip- ment tire should be repaired (or replaced) and reinstalled on your vehicle at the first opportunity. Do not install a wheel cover or attempt to mount a conventional tire on the compact spare wheel, since the wheel is designed specifically fo...

  • Page 411

    Your original equipment tire, replace (or repair) the original equipment tire and reinstall on the vehicle at the first opportunity. Warning! Limited-use spares are for emergency use only. In- stallation of this limited-use spare tire affects vehicle handling. With this tire, do not drive more than ...

  • Page 412

    Tread wear indicators tread wear indicators are in the original equipment tires to help you in determining when your tires should be replaced. These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth becomes 1/16 in (2 mm). When the tread is wo...

  • Page 413

    Keep dismounted tires in a cool, dry place with as little exposure to light as possible. Protect tires from contact with oil, grease, and gasoline. Replacement tires the tires on your new vehicle provide a balance of many characteristics. They should be inspected regularly for wear and correct cold ...

  • Page 414

    Warning! (continued) • failure to equip your vehicle with tires having adequate speed capability can result in sudden tire failure and loss of vehicle control. Caution! Replacing original tires with tires of a different size may result in false speedometer and odometer read- ings. Tire chains (tract...

  • Page 415

    Caution! (continued) • because of restricted traction device clearance be- tween tires and other suspension components, it is important that only traction devices in good con- dition are used. Broken devices can cause serious damage. Stop the vehicle immediately if noise occurs that could indicate d...

  • Page 416

    Snow tires generally have lower speed ratings than what was originally equipped with your vehicle and should not be operated at sustained speeds over 75 mph (120 km/h). For speeds above 75 mph (120 km/h) refer to original equipment or an authorized tire dealer for recommended safe operating speeds, ...

  • Page 417

    Tire pressure monitor system (tpms) the tire pressure monitoring system (tpms) will warn the driver of a low tire pressure based on the vehicle recommended cold tire pressure. The tire pressure will vary with temperature by about 1 psi (7 kpa) for every 12°f (6.5°c). This means that when the outside...

  • Page 418

    Cold tire pressure. Once the low tire pressure warning has been illuminated, the tire pressure must be increased to the recommended cold tire pressure in order for the tire pressure monitoring telltale light to be turned off. The system will automatically update and the tire pressure monitoring tell...

  • Page 419

    Caution! (continued) • after inspecting or adjusting the tire pressure always reinstall the valve stem cap. This will prevent moisture and dirt from entering the valve stem, which could damage the tire pressure moni- toring sensor. Note: • the tpms is not intended to replace normal tire care and mai...

  • Page 420

    The tpms consists of the following components: • receiver module • four tire pressure monitoring sensors • tire pressure monitoring telltale light a low spare tire will not cause the tire pressure moni- toring telltale light to illuminate, a warning message to appear, or the chime to sound. The tire...

  • Page 421

    2. Installing some form of aftermarket window tinting that affects radio wave signals. 3. Lots of snow or ice around the wheels or wheel housings. 4. Using tire chains on the vehicle. 5. Using wheels/tires not equipped with tpm sensors. Note: there is no tire pressure monitoring sensor in the spare ...

  • Page 422

    Premium system – if equipped the tire pressure monitor system (tpms) uses wireless technology with wheel rim-mounted electronic sensors to monitor tire pressure levels. Sensors, mounted to each wheel as part of the valve stem, transmit tire pressure readings to the receiver module. Note: it is parti...

  • Page 423

    Should a low tire condition occur on any of the four active road tire(s), you should stop as soon as possible, and inflate the low tire(s) that is “flashing” on the graphic display to the vehicle’s recommended cold tire pressure. The system will automatically update, the graphic dis- play of the pre...

  • Page 424

    Note: your system can be set to display pressure units in psi, kpa, or bar. If the ignition switch is cycled, this sequence will repeat, providing the system fault still exists. If the system fault no longer exists, the tire pressure monitoring telltale light will no longer flash, the ⬙service tpm s...

  • Page 425

    ⬙service tpm system⬙ message is then followed by a graphic display, with pressure values still shown. This indicates the pressure values are still being received from the tpm sensors but they may not be located in the correct vehicle position. However, the system still needs to be serviced as long a...

  • Page 426

    General information this device complies with part 15 of the fcc rules and rss 210 of industry canada. Operation is subject to the following conditions: • this device may not cause harmful interference. • this device must accept any interference received, including interference that may cause undesi...

  • Page 427

    Optimum performance. The use of premium gasoline is not recommended, as it will not provide any benefit over regular gasoline in these engines. Light spark knock at low engine speeds is not harmful to your engine. However, continued heavy spark knock at high speeds can cause damage and immediate ser...

  • Page 428

    Caution! Do not use gasoline containing methanol or gaso- line containing more than 10% ethanol. Use of these blends may result in starting and driveability prob- lems, damage critical fuel system components, cause emissions to exceed the applicable standard, and/or cause the “malfunction indicator ...

  • Page 429

    Mmt in gasoline mmt is a manganese-containing metallic additive that is blended into some gasoline to increase octane. Gasoline blended with mmt provides no performance advantage beyond gasoline of the same octane number without mmt. Gasoline blended with mmt reduces spark plug life and reduces emis...

  • Page 430

    Caution! (continued) • an out-of-tune engine or certain fuel or ignition malfunctions can cause the catalytic converter to overheat. If you notice a pungent burning odor or some light smoke, your engine may be out of tune or malfunctioning and may require immediate service. Contact your authorized d...

  • Page 431

    Warning! (continued) • guard against carbon monoxide with proper maintenance. Have the exhaust system inspected every time the vehicle is raised. Have any abnor- mal conditions repaired promptly. Until repaired, drive with all side windows fully open. • keep the liftgate closed when driving your veh...

  • Page 432

    Caution! Only vehicles with the e-85 fuel filler door label can operate on e-85. Ethanol fuel (e-85) e-85 is a mixture of approximately 85% fuel ethanol and 15% unleaded gasoline. Warning! Ethanol vapors are extremely flammable and could cause serious personal injury. Never have any smok- ing materi...

  • Page 433

    When you do switch fuel types it is recommended that: • you do not switch when the fuel gauge indicates less than 1/4 full • you do not add less than 5 gallons (19 liters) when refueling • you operate the vehicle immediately after refueling for a period of at least 5 minutes observing these precauti...

  • Page 434

    Starting the characteristics of e-85 fuel make it unsuitable for use when ambient temperatures fall below 0°f (-18°c). In the range of 0°f (-18°c) to 32°f (0°c), you may experience an increase in the time it takes for your engine to start, and a deterioration in driveability (sags and/or hesitations...

  • Page 435

    Adding fuel fuel filler cap (gas cap) the gas cap is located behind the locking fuel filler door, on the driver’s side of the vehicle. If the gas cap is lost or damaged, be sure the replacement cap is for use with this vehicle. 1. Press the fuel filler door release switch (located under the headlamp...

  • Page 436

    2. Open the fuel filler door, and remove the fuel filler cap. Caution! • damage to the fuel system or emission control system could result from using an improper fuel cap (gas cap). A poorly fitting cap could let impu- rities into the fuel system. Also, a poorly fitting aftermarket cap can cause the...

  • Page 437

    Warning! • never have any smoking materials lit in or near the vehicle when the gas cap is removed or the tank is being filled. • never add fuel when the engine is running. This is in violation of most state and federal fire regula- tions and may cause the malfunction indicator light to turn on. • a...

  • Page 438

    Loose fuel filler cap message if the vehicle diagnostic system determines that the fuel filler cap is loose, improperly installed, or damaged, a loose gascap indicator will display in the evic telltale display area. Refer to “electronic vehicle information center (evic)” in “understanding your instr...

  • Page 439

    Gross axle weight rating (gawr) the gawr is the maximum permissible load on the front and rear axles. The load must be distributed in the cargo area so that the gawr of each axle is not exceeded. Each axle’s gawr is determined by the components in the system with the lowest load carrying capacity (a...

  • Page 440

    The entire vehicle should first be weighed on a commer- cial scale to ensure that the gvwr has not been ex- ceeded. The weight on the front and rear of the vehicle should then be determined separately to be sure that the load is properly distributed over front and rear axle. Weighing the vehicle may...

  • Page 441

    Common towing definitions the following trailer towing related definitions will assist you in understanding the following information. Gross vehicle weight rating (gvwr) the gvwr is the total allowable weight of your vehicle. This includes driver, passengers, cargo and trailer tongue weight. The tot...

  • Page 442

    Rear gawr. Refer to “vehicle loading/vehicle certifica- tion label” in “starting and operating” for further information. Warning! It is important that you do not exceed the maximum front or rear gawr. A dangerous driving condition can result if either rating is exceeded. You could lose control of th...

  • Page 443

    Trailer stability. Trailer sway control and a weight- distributing (load equalizing) hitch are recommended for heavier trailer tongue weights (tw) and may be required depending on vehicle and trailer configuration/loading to comply with gross axle weight rating (gawr) requirements. Warning! • an imp...

  • Page 444

    With weight-distributing hitch (correct) improper adjustment of weight-distributing hitch (incorrect) 442 starting and operating.

  • Page 445

    Trailer hitch classification your vehicle may be factory equipped for safe towing of trailers weighing over 3,500 lbs (1 587 kg) with the optional trailer tow prep package. See your authorized dealer for package content. The following chart provides the industry standard for the maximum trailer weig...

  • Page 446

    Trailer towing weights (maximum trailer weight ratings) the following chart provides the maximum trailer weight ratings towable for your given drivetrain. Engine/model model gcwr (gross com- bined wt. Rating) frontal area max. Gtw (gross trailer wt.) max. Trailer tongue wt. (see note) 3.6l 4x2 8,900...

  • Page 447

    Trailer and tongue weight always load a trailer with 60% to 65% of the weight in the front of the trailer. This places 10% to 15% of the gross trailer weight (gtw) on the tow hitch of your vehicle. Loads balanced over the wheels, or heavier in the rear, can cause the trailer to sway severely side-to...

  • Page 448

    Note: remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options, or authorized dealer-installed options, must be considered as part of the total load on your vehicle. Refer to “tire safety information/tire and loading information...

  • Page 449

    Warning! (continued) • make certain that the load is secured in the trailer and will not shift during travel. When trailering cargo that is not fully secured, dynamic load shifts can occur that may be difficult for the driver to control. You could lose control of your vehicle and have a collision. •...

  • Page 450

    Towing requirements – tires − do not attempt to tow a trailer while using a compact spare tire. − proper tire inflation pressures are essential to the safe and satisfactory operation of your vehicle. Refer to “tires – general information” in “starting and oper- ating” for proper tire inflation proce...

  • Page 451

    Caution! If the trailer weighs more than 1,000 lbs (454 kg) loaded, it should have its own brakes and they should be of adequate capacity. Failure to do this could lead to accelerated brake lining wear, higher brake pedal effort, and longer stopping distances. Warning! • do not connect trailer brake...

  • Page 452

    The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector. Refer to the following illustrations. Four-pin connector 1 — female pins 4 — park 2 — male pin 5 — left stop/turn 3 — ground 6 — right stop/turn seven-pin connector 1 — battery 5 — ground...

  • Page 453

    Towing tips before setting out on a trip, practice turning, stopping and backing the trailer in an area away from heavy traffic. Automatic transmission the drive range can be selected when towing. How- ever, if frequent shifting occurs while in this range, the tow/haul mode (if equipped), or a lower...

  • Page 454

    Cooling system to reduce potential for engine and transmission over- heating, take the following actions: − city driving when stopped for short periods of time, shift the trans- mission into neutral and increase engine idle speed. − highway driving reduce speed. − air conditioning turn off temporari...

  • Page 455

    Recreational towing (behind motorhome, etc.) towing this vehicle behind another vehicle towing condition wheel off the ground two-wheel drive models four-wheel drive models flat tow none not allowed see instructions • transmission in park • transfer case in neutral (n) • tow in forward direction dol...

  • Page 456

    Recreational towing — two-wheel drive models do not flat tow this vehicle. Damage to the drivetrain will result. Recreational towing (for two-wheel drive models) is allowed only if the rear wheels are off the ground. This may be accomplished using a tow dolly or vehicle trailer. If using a tow dolly...

  • Page 457

    Note: this vehicle may be towed on a flatbed or vehicle trailer provided all four wheels are off the ground. Caution! Towing this vehicle in violation of the above require- ments can cause severe transmission and/or transfer case damage. Damage from improper towing is not covered under the new vehic...

  • Page 458

    Caution! (continued) • do not use a bumper-mounted clamp-on tow bar on your vehicle. The bumper face bar will be damaged. Shifting into neutral (n) warning! You or others could be injured if you leave the vehicle unattended with the transfer case in the neutral (n) position without first fully engag...

  • Page 459

    4. Turn the ignition switch to the on/run position, but do not start the engine. 5. Press and hold the brake pedal. 6. Shift the transmission into neutral. 7. Using the point of a ballpoint pen or similar object, press and hold the recessed transfer case n (neutral) button (located by the selector s...

  • Page 460

    12. Firmly apply the parking brake. 13. Shift the transmission into park and remove the key fob. Caution! Damage to the transmission may occur if the trans- mission is shifted into park with the transfer case in neutral (n) and the engine running. With the transfer case in neutral (n) ensure that th...

  • Page 461

    Shifting out of neutral (n) use the following procedure to prepare your vehicle for normal usage. 1. Bring the vehicle to a complete stop, leaving it con- nected to the tow vehicle. 2. Firmly apply the parking brake. 3. Turn the key fob to the on/run position, but do not start the engine. 4. Press a...

  • Page 462

    Note: when shifting out of transfer case neutral (n), turning the engine off may be required to avoid gear clash. 7. Shift the transmission into park. 8. Release the brake pedal. 9. Disconnect vehicle from the tow vehicle. 10. Start the engine. 11. Press and hold the brake pedal. 12. Release the par...

  • Page 463: Contents

    What to do in emergencies contents 䡵 hazard warning flashers . . . . . . . . . . . . . . . . 462 䡵 if your engine overheats . . . . . . . . . . . . . . . . 462 䡵 jacking and tire changing . . . . . . . . . . . . . . . 463 ▫ jack location . . . . . . . . . . . . . . . . . . . . . . . 464 ▫ spare tire...

  • Page 464

    Hazard warning flashers the hazard warning flasher switch is located on the switch bank just above the climate controls. Press the switch to turn on the hazard warning flasher. When the switch is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency. ...

  • Page 465

    • you can also turn the temperature control to maximum heat, the mode control to floor and the blower control to high. This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system. Caution! Driving with a hot cooling system could damage ...

  • Page 466

    Warning! (continued) • being under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never put any part of your body under a vehicle that is on a jack. • never start or run the engine while the vehicle is on a jack. If you need to get under ...

  • Page 467

    Preparations for jacking 1. Park the vehicle on a firm, level surface. Avoid ice or slippery surfaces. Warning! Do not attempt to change a tire on the side of the vehicle closest to moving traffic, pull far enough off the road to avoid being hit when operating the jack or changing the wheel. 2. Turn...

  • Page 468

    Jacking instructions warning! Carefully follow these tire changing warnings to help prevent personal injury or damage to your vehicle: • always park on a firm, level surface as far from the edge of the roadway as possible before raising the vehicle. • turn on the hazard warning flasher. • block the ...

  • Page 469

    Caution! Do not attempt to raise the vehicle by jacking on locations other than those indicated in the jacking instructions for this vehicle. 1. Remove the spare tire, jack, and tools from storage. 2. Loosen (but do not remove) the wheel lug nuts by turning them to the left, one turn, while the whee...

  • Page 470

    4. For the front axle, place the jack and protective cap on the body flange just behind the front tire as indicated by the triangular lift point symbol on the sill molding. Do not raise the vehicle until you are sure the jack is fully engaged. 5. For a rear tire, place the jack and protective cap in...

  • Page 471

    Lift point symbol on sill molding rear jacking location 6 what to do in emergencies 469.

  • Page 472

    6. Raise the vehicle by turning the jack screw clockwise. Raise the vehicle only until the tire just clears the surface and enough clearance is obtained to install the spare tire. Minimum tire lift provides maximum stability. Warning! Raising the vehicle higher than necessary can make the vehicle le...

  • Page 473

    12. Securely store the road wheel and jack in the cargo area. 13. Have the aluminum road wheel and tire repaired as soon as possible, properly secure the spare tire with the special wing nut torqued to 3.7 ft-lbs (5 n·m), reinstall the jack and tool kit foam tray, and latch the rear load floor cover...

  • Page 474

    Note: when using a portable battery booster pack follow the manufacturer’s operating instructions and precautions. Caution! Do not use a portable battery booster pack or any other booster source with a system voltage greater than 12 volts or damage to the battery, starter motor, alternator or electr...

  • Page 475

    Warning! • take care to avoid the radiator cooling fan when- ever the hood is raised. It can start anytime the ignition switch is on. You can be injured by moving fan blades. • remove any metal jewelry such as watch bands or bracelets that might make an inadvertent electrical contact. You could be s...

  • Page 476

    Caution! Failure to follow these procedures could result in damage to the charging system of the booster vehicle or the discharged vehicle. 1. Connect the positive (+) end of the jumper cable to the remote positive (+) post of the discharged vehicle. 2. Connect the opposite end of the positive (+) j...

  • Page 477

    8. Disconnect the opposite end of the positive (+) jumper cable from the positive (+) post of the booster battery. 9. Disconnect the positive (+) end of the jumper cable from the remote positive (+) post of the discharged vehicle. 10. Reinstall the protective cover over the remote posi- tive (+) bat...

  • Page 478

    Caution! Tow hooks are for emergency use only, to rescue a vehicle stranded off road. Do not use tow hooks for tow truck hookup or highway towing. You could damage your vehicle. Shift lever override if a malfunction occurs and the shift lever cannot be moved out of the park position, you can use the...

  • Page 479

    7. Move the shift lever into the neutral position. 8. The vehicle may then be started in neutral. 9. Reinstall the shift lever override access cover and install the rubber liner into the cupholder. Towing a disabled vehicle this section describes procedures for towing a disabled vehicle using a comm...

  • Page 480

    Towing condition wheels off the ground 2wd models 4wd models flat tow none if transmission is operable: • trans in neutral • 30 mph max(48 km/h) • 15 miles (24 km) max distance see instructions in “recreational tow- ing” under “starting and operating” • trans in park • t/case in neutral • tow in for...

  • Page 481

    If the vehicle’s battery is discharged, see brake/ transmission interlock manual override (under starting and operating, automatic transmission) for instructions on shifting the automatic transmission out of the park position for towing. Caution! • do not attempt to use sling type equipment when tow...

  • Page 482

    Caution! Towing faster than 30 mph (48 km/h) or farther than 15 miles (24 km) with rear wheels on the ground can cause severe damage to the transmission. Such dam- age is not covered by the new vehicle limited warranty. If the transmission is not operable, or the vehicle must be towed faster than 30...

  • Page 483: Maintaining Your Vehicle

    Maintaining your vehicle contents 䡵 engine compartment – 3.6l . . . . . . . . . . . . . . 483 䡵 engine compartment – 5.7l . . . . . . . . . . . . . . 484 䡵 onboard diagnostic system – obd ii . . . . . . . 485 ▫ loose fuel filler cap message . . . . . . . . . . . 485 䡵 emissions inspection and mainte...

  • Page 484

    ▫ brake system . . . . . . . . . . . . . . . . . . . . . . . 507 ▫ front/rear axle fluid . . . . . . . . . . . . . . . . . 509 ▫ transfer case . . . . . . . . . . . . . . . . . . . . . . . 510 ▫ automatic transmission . . . . . . . . . . . . . . . 511 ▫ appearance care and protection from corrosion ...

  • Page 485

    Engine compartment – 3.6l 1 — totally integrated power module (fuses) 6 — air cleaner filter 2 — engine oil dipstick 7 — washer fluid reservoir 3 — engine oil fill 8 — coolant pressure cap (radiator) 4 — brake fluid reservoir 9 — engine coolant reservoir 5 — power steering fluid reservoir 7 maintain...

  • Page 486

    Engine compartment – 5.7l 1 — totally integrated power module (fuses) 6 — washer fluid reservoir 2 — automatic transmission dipstick 7 — engine oil dipstick 3 — engine oil fill 8 — coolant pressure cap (radiator) 4 — brake fluid reservoir 9 — engine coolant reservoir 5 — air cleaner filter 484 maint...

  • Page 487

    Onboard diagnostic system – obd ii your vehicle is equipped with a sophisticated onboard diagnostic system called obd ii. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide ex...

  • Page 488

    The select button to turn off the message. If the problem continues, the message will appear the next time the vehicle is started. A loose, improperly installed, or damaged fuel filler cap may also turn on the malfunction indicator light (mil). Emissions inspection and maintenance programs in some l...

  • Page 489

    4. Approximately 15 seconds later, one of two things will happen: a. The mil will flash for about 10 seconds and then return to being fully illuminated until you turn off the ignition or start the engine. This means that your vehicle’s obd ii system is not ready and you should not proceed to the i/m...

  • Page 490

    Dealer service your authorized dealer has the qualified service person- nel, special tools, and equipment to perform all service operations in an expert manner. Service manuals are available which include detailed service information for your vehicle. Refer to these service manuals before attempting...

  • Page 491

    Caution! (continued) • your vehicle has been built with improved fluids that protect the performance and durability of your vehicle and also allow extended maintenance intervals. Do not use chemical flushes in these components as the chemicals can damage your engine, transmission, power steering or ...

  • Page 492

    Change engine oil the oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance. Refer to “maintenance schedule” for further information. Note: under no circumstances should oil change intervals exceed 8,000 miles (13 000 km) or six months, whichev...

  • Page 493

    Engine oil viscosity – 3.6l engine sae 5w-30 engine oil is recommended for all operating temperatures. This engine oil improves low temperature starting and vehicle fuel economy. The engine oil filler cap also shows the recommended engine oil viscosity for your vehicle. For information on engine oil...

  • Page 494

    Materials added to engine oils do not add any supplemental materials, other than leak detection dyes, to your engine oil. Engine oil is an engineered product and its performance may be im- paired by supplemental additives. Disposing of used engine oil and oil filters care should be taken in disposin...

  • Page 495

    Warning! The air induction system (air cleaner, hoses, etc) can provide a measure of protection in the case of engine backfire. Do not remove the air induction system (air cleaner, hoses, etc.) unless such removal is necessary for repair or maintenance. Make sure that no one is near the engine compa...

  • Page 496

    Warning! (continued) • battery gas is flammable and explosive. Keep flame or sparks away from the battery. Do not use a booster battery or any other booster source with an output greater than 12 volts. Do not allow cable clamps to touch each other. • battery posts, terminals, and related accessories...

  • Page 497

    Air conditioner maintenance for best possible performance, your air conditioner should be checked and serviced by an authorized dealer at the start of each warm season. This service should include cleaning of the condenser fins and a performance test. Drive belt condition should also be checked at t...

  • Page 498

    Refrigerant recovery and recycling r-134a air conditioning refrigerant is a hydrofluoro- carbon (hfc) that is endorsed by the environmental protection agency (epa) and is an ozone-saving product. However, the manufacturer recommends that air condi- tioning service be performed by authorized dealers ...

  • Page 499

    Avoid using the wiper blades to wipe frost or ice from the windshield. Keep the blade rubber out of contact with petroleum products such as engine oil, gasoline, etc. Note: life expectancy of wiper blades varies depend- ing on geographical area and frequency of use. Poor performance of blades may be...

  • Page 500

    3. Grab the bottom of the wiper blade and rotate it forward to unsnap the blade pivot pin from the wiper blade holder. 4. Install the wiper blade pivot pin into the wiper blade holder at the end of the wiper arm, and firmly press the wiper blade until it snaps into place. 5. Lower the wiper blade an...

  • Page 501

    Clean the wiper blades, this will help blade performance. To prevent freeze-up of your windshield washer system in cold weather, select a solution or mixture that meets or exceeds the temperature range of your climate. This rating information can be found on most washer fluid containers. Warning! Co...

  • Page 502

    Warning! • exhaust gases can injure or kill. They contain carbon monoxide (co), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing co, refer to “safety tips/exhaust gas” in “things to know before starting your vehicle” for further...

  • Page 503

    Under normal operating conditions, the catalytic con- verter will not require maintenance. However, it is im- portant to keep the engine properly tuned to assure proper catalyst operation and prevent possible catalyst damage. Note: intentional tampering with emissions control systems can result in c...

  • Page 504

    Cooling system warning! You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator. If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool. Never try to open a cooling system pressure cap when the radiat...

  • Page 505

    Cooling system – drain, flush, and refill if the engine coolant (antifreeze) is dirty and contains a considerable amount of sediment, clean and flush with reliable cooling system cleaner. Follow with a thorough rinsing to remove all deposits and chemicals. Properly dispose of the old engine coolant ...

  • Page 506

    Caution! (continued) • this vehicle has not been designed for use with propylene glycol-based engine coolant (anti- freeze). Use of propylene glycol-based engine coolant (antifreeze) is not recommended. Adding coolant your vehicle has been built with an improved engine coolant (antifreeze) that allo...

  • Page 507

    Note: mixing engine coolant (antifreeze) types will decrease the life of the engine coolant (antifreeze) and will require more frequent engine coolant (antifreeze) changes. Cooling system pressure cap the cap must be fully tightened to prevent loss of engine coolant (antifreeze), and to ensure that ...

  • Page 508

    Disposal of used engine coolant used ethylene glycol-based engine coolant (antifreeze) is a regulated substance requiring proper disposal. Check with your local authorities to determine the disposal rules for your community. To prevent ingestion by ani- mals and children, do not store ethylene glyco...

  • Page 509

    If an examination of your engine compartment shows no evidence of radiator or hose leaks, the vehicle may be safely driven. The vapor will soon dissipate. • do not overfill the coolant recovery bottle. • check engine coolant (antifreeze) freeze point in the radiator and in the coolant recovery bottl...

  • Page 510

    Warning! Riding the brakes can lead to brake failure and possibly a collision. Driving with your foot resting or riding on the brake pedal can result in abnormally high brake temperatures, excessive lining wear, and possible brake damage. You would not have your full braking capacity in an emergency...

  • Page 511

    Warning! (continued) • to avoid contamination from foreign matter or moisture, use only new brake fluid or fluid that has been in a tightly closed container. Keep the master cylinder reservoir cap secured at all times. Brake fluid in a open container absorbs moisture from the air resulting in a lowe...

  • Page 512

    The front axle fill and drain plugs should be tightened to 22 to 29 ft lbs (30 to 40 n·m). Caution! Do not over tighten the plugs as it could damage them and cause them to leak. Rear axle fluid level check the rear axle oil level needs to be between 1/8 in (3 mm) below the bottom of the fill hole an...

  • Page 513

    Adding fluid add fluid at the filler hole, until it runs out of the hole, when the vehicle is in a level position. Drain first remove fill plug, then remove drain plug. Recom- mended tightening torque for drain and fill plugs is 15 to 25 ft lbs (20 to 34 n·m). Caution! When installing plugs, do not ...

  • Page 514

    Caution! Using a transmission fluid other than the manufac- turer’s recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder. Using a transmission fluid other than the manufacturer’s recommended fluid will result in more frequent fluid and filter change...

  • Page 515

    Caution! • using a transmission fluid other than the manu- facturer’s recommended fluid may cause deterio- ration in transmission shift quality and/or torque converter shudder. Using a transmission fluid other than that recommended by the manufacturer will result in more frequent fluid and filter ch...

  • Page 516

    6. Remove the dipstick again, and note the fluid level on both sides. The fluid level should be between the “hot” (upper) reference holes on the dipstick at normal operat- ing temperature. The fluid level is only valid if there is a solid coating of oil on both sides of the dipstick. If the fluid is...

  • Page 517

    Appearance care and protection from corrosion protection of body and paint from corrosion vehicle body care requirements vary according to geo- graphic locations and usage. Chemicals that make roads passable in snow and ice, and those that are sprayed on trees and road surfaces during other seasons,...

  • Page 518

    • avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish. Caution! • do not use abrasive or strong cleaning materials such as steel wool or scouring powder, which will scratch metal and painted surfaces. • use of power washers exceeding 1,200 psi (8...

  • Page 519

    • use mopar威 touch up paint or equivalent on scratches or chips as soon as possible. Your authorized dealer has touch up paint to match the color of your vehicle. Wheel and wheel trim care all wheels and wheel trim, especially aluminum and chrome-plated wheels should be cleaned regularly with a mild...

  • Page 520

    Interior care use mopar 威 total clean or equivalent to clean fabric upholstery and carpeting. Interior trim should be cleaned starting with a damp cloth, a damp cloth with mopar 威 total clean or equiva- lent, then mopar 威 spot & stain remover or equivalent, if absolutely necessary. Do not use harsh ...

  • Page 521

    To minimize the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth. To remove road dirt, wash with a mild soap solution fol- lowed by rinsing. Do not use abrasive cleaning components, solvents, steel wool or other aggressive material to clean the lenses. Gl...

  • Page 522

    Replace the belts if they appear frayed or worn or if the buckles do not work properly. Fuses totally integrated power module the totally integrated power module is located in the engine compartment. This center contains cartridge fuses and mini fuses. A description of each fuse and compo- nent may ...

  • Page 523

    Cavity cartridge fuse mini fuse description j03 30 amp pink trailer tow j04 25 amp natural driver door node j05 25 amp natural passenger door node j06 40 amp green antilock brakes pump/stability con- trol system j07 30 amp pink antilock brakes valve/stability control system j08 40 amp green power se...

  • Page 524

    Cavity cartridge fuse mini fuse description j18 20 amp blue powertrain control module/powertrain control module trans- mission range j19 60 amp yellow radiator fan motor hi/radiator fan mo- tor low j20 30 amp pink front wiper j21 20 amp blue front/rear washer control j22 25 amp natural sunroof modul...

  • Page 525

    Cavity cartridge fuse mini fuse description m11 10 amp red heating, ventilation & air conditioning (cli- mate control system) m12 30 amp green radio/amplifier m13 20 amp yellow instrument cluster m14 20 amp yellow back up camera m15 20 amp yellow power seat module(s)/adaptive cruise control/audio te...

  • Page 526

    Cavity cartridge fuse mini fuse description m26 10 amp red driver door switch bank m27 10 amp red ignition switch/ wireless control module/keyless entry module m28 15 amp blue powertrain controller/ transmission control- ler m29 10 amp red tire pressure monitor m30 15 amp blue j1962 diag connector m...

  • Page 527

    Caution! • when installing the totally integrated power mod- ule cover, it is important to ensure the cover is properly positioned and fully latched. Failure to do so may allow water to get into the totally integrated power module and possibly result in a electrical system failure. • when replacing ...

  • Page 528

    Replacement bulbs interior lights bulb type glove box lamp . . . . . . . . . . . . . . . . . . . . . . . . . 194 grab handle lamp . . . . . . . . . . . . . . . . L002825w5w overhead console reading lamps . . . . . . . . . Vt4976 rear cargo lamp . . . . . . . . . . . . . . . . . . . . . . . 214–2 vis...

  • Page 529

    Bulb replacement high intensity discharge headlamps (hid) – if equipped the headlamps are a type of high voltage discharge tube. High voltage can remain in the circuit even with the headlamp switch off and the key removed. Because of this, you should not attempt to service a headlamp bulb yourself. ...

  • Page 530

    Caution! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol. Front turn signal 1. Open the hood. 2. Turn the turn signal bulb one–quarter turn counter- clockwise to re...

  • Page 531

    Caution! • do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol. • always use the correct bulb size and type for replacement. An incorrect bulb size or type may overheat...

  • Page 532

    Rear tail, stop, turn signal, and backup lamps 1. Raise the liftgate. 2. Remove the two push-pins from the tail lamp housing. 3. Grasp the tail lamp and pull firmly rearward to disengage the lamp from the aperture panel. 4. Twist socket counter clockwise and remove from lamp. 5. Pull the bulb to rem...

  • Page 533

    Rear liftgate mounted tail lamp 1. Raise the liftgate. 2. Use a fiber stick or flat blade screw driver to pry the lower trim from the liftgate. 3. Once lower trim is loose, close the liftgate. 4. Open the flipper glass. 5. Pull up glass seal at bottom of window opening. 6. Remove small trim panel ar...

  • Page 534

    Center high-mounted stop lamp (chmsl) the center high-mounted stop lamp is an led assembly. See your authorized dealer for replacement. Rear license lamp 1. Use a screw driver to gently pry against the side of the snap tab to remove the license lamp lens. 2. Pull bulb from socket. 3. Replace bulb. 4...

  • Page 535

    Fluid capacities u.S. Metric fuel (approximate) 3.6l and 5.7l engines 24 gallons 91 liters engine oil with filter 3.6l engine (sae 5w-30, api certified) 6 quarts 5.6 liters 5.7l engine (sae 5w-20, api certified) 7 quarts 6.6 liters cooling system * 3.6l engine (mopar 威 engine coolant/antifreeze 5-ye...

  • Page 536

    Fluids, lubricants, and genuine parts engine component fluid, lubricant, or genuine part engine coolant mopar 威 antifreeze/coolant 5 year/100,000 mile formula hoat (hy- brid organic additive technology) or equivalent. Engine oil – 3.6l engine use api certified sae 5w-30 engine oil, meeting the requi...

  • Page 537

    Chassis component fluid, lubricant, or genuine part automatic transmission mopar 威 atf+4威 automatic transmission fluid or equivalent licensed atf+4 威 product. Transfer case – 3.6l engine shell automatic transmission fluid 3353 or equivalent. Transfer case – 5.7l engine mopar 威 atf+4威 automatic trans...

  • Page 538

    Component fluid, lubricant, or genuine part power steering reservoir – 3.6l engine mopar 威 hydraulic fluid or equivalent meeting ms-1165, such as fuchs eg zh 3044 or pentosin chf 11s. Power steering reservoir – 5.7l engine mopar 威 power steering fluid +4, mopar威 atf+4威 automatic trans- mission fluid...

  • Page 539: Maintenance Schedules

    Maintenance schedules contents 䡵 maintenance schedule . . . . . . . . . . . . . . . . . . 538 ▫ required maintenance intervals . . . . . . . . . . 539 8 m a i n t e n a n c e s c h e d u l e s.

  • Page 540

    Maintenance schedule the scheduled maintenance services listed in this manual must be done at the times or mileages specified to protect your vehicle warranty and ensure the best vehicle performance and reliability. More frequent main- tenance may be needed for vehicles in severe operating condition...

  • Page 541

    Referring to the steps described under “electronic vehicle information center (evic)/oil change required” in “understanding your instrument panel” for further in- formation. At each stop for fuel • check the engine oil level about five minutes after a fully warmed engine is shut off. Checking the oi...

  • Page 542

    8,000 miles (13,000 km) or 6 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 8,000 miles (13 000 km). Odometer reading date repair order # dealer code signature authorized chry...

  • Page 543

    24,000 miles (39,000 km) or 18 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 24,000 miles (39 000 km). ❏ inspect the cv joints. ❏ inspect exhaust system. ❏ inspect the front ...

  • Page 544

    40,000 miles (65,000 km) or 30 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 40,000 miles (65 000 km). Odometer reading date repair order # dealer code signature authorized c...

  • Page 545

    56,000 miles (91,000 km) or 42 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 56,000 miles (91 000 km). Odometer reading date repair order # dealer code signature authorized c...

  • Page 546

    64,000 miles (104,000 km) or 48 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 64,000 miles (104 000 km). ❏ replace the engine air cleaner filter. ❏ replace the air conditioni...

  • Page 547

    72,000 miles (117,000 km) or 54 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 72,000 miles (117 000 km). ❏ inspect the cv joints. ❏ inspect exhaust system. ❏ inspect the fron...

  • Page 548

    88,000 miles (143,000 km) or 66 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 88,000 miles (143 000 km). Odometer reading date repair order # dealer code signature authorized...

  • Page 549

    96,000 miles (156,000 km) or 72 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 96,000 miles (156 000 km). ❏ replace the engine air cleaner filter. ❏ replace the air conditioni...

  • Page 550

    104,000 miles (169,000 km) or 78 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 104,000 miles (169 000 km). ❏ flush and replace the engine coolant if not done at 60 months. Od...

  • Page 551

    120,000 miles (195,000 km) or 90 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 120,000 miles (195 000 km). ❏ inspect the cv joints. ❏ inspect exhaust system. ❏ inspect the fr...

  • Page 552

    128,000 miles (208,000 km) or 96 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 128,000 miles (208 000 km). ❏ replace the engine air cleaner filter. ❏ replace the air conditio...

  • Page 553

    144,000 miles (234,000 km) or 108 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 144,000 miles (234 000 km). ❏ if using your vehicle for any of the following: dusty or off-roa...

  • Page 554

    † this maintenance is recommended by the manufacturer to the owner, but is not required to maintain emissions warranty. Warning! • you can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about...

  • Page 555: Contents

    If you need consumer assistance contents 䡵 suggestions for obtaining service for your vehicle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 555 ▫ prepare for the appointment . . . . . . . . . . . 555 ▫ prepare a list . . . . . . . . . . . . . . . . . . . . . . 555 ▫ be reasonable with r...

  • Page 556

    䡵 department of transportation uniform tire quality grades . . . . . . . . . . . . . . . . . . . . . . . . 561 ▫ treadwear . . . . . . . . . . . . . . . . . . . . . . . . . 561 ▫ traction grades . . . . . . . . . . . . . . . . . . . . . 561 ▫ temperature grades . . . . . . . . . . . . . . . . . . 56...

  • Page 557

    Suggestions for obtaining service for your vehicle prepare for the appointment if you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty. Discuss additional charges with the service manager. ...

  • Page 558

    This is why you should always talk to an authorized dealer’s service manager first. Most matters can be re- solved with this process. • if for some reason you are still not satisfied, talk to the general manager or owner of the authorized dealer- ship. They want to know if you need assistance. • if ...

  • Page 559

    Customer assistance for the hearing or speech impaired (tdd/tty) to assist customers who have hearing difficulties, the manufacturer has installed special tdd (telecommuni- cation devices for the deaf) equipment at its customer center. Any hearing or speech impaired customer, who has access to a tdd...

  • Page 560

    We appreciate that you have made a major investment when you purchased the vehicle. An authorized dealer has also made a major investment in facilities, tools, and training to assure that you are absolutely delighted with the ownership experience. You’ll be pleased with their sincere efforts to reso...

  • Page 561

    If nhtsa receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, nhtsa cannot become involved in individual problems between you, your authorized dealer, and the manufacturer. T...

  • Page 562

    • service manuals these comprehensive service manuals provide the information that students and professional technicians need in diagnosing/troubleshooting, problem solving, maintaining, servicing, and repairing chrysler group llc vehicles. A complete working knowledge of the vehicle, system, and/or...

  • Page 563

    Department of transportation uniform tire quality grades the following tire grading categories were established by the national highway traffic safety administration. The specific grade rating assigned by the tire’s manufacturer in each category is shown on the sidewall of the tires on your vehicle....

  • Page 564

    Temperature grades the temperature grades are a (the highest), b, and c, representing the tire’s resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the mater...

  • Page 565: Index

    Index 10

  • Page 566

    Adaptive cruise control (acc) (cruise control) . . 167 adding fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . 433 additives, fuel . . . . . . . . . . . . . . . . . . . . . . . . . 427 air cleaner, engine (engine air cleaner filter) . . . 492 air conditioner maintenance . . . . . . . . . ....

  • Page 567

    Fluid level check . . . . . . . . . . . . . . . . . . . 512,513 fluid type . . . . . . . . . . . . . . . . . . . . . . . . . . . 511 special additives . . . . . . . . . . . . . . . . . . . . . . 512 torque converter . . . . . . . . . . . . . . . . . . . . . . 356 autostick . . . . . . . . . . . . . ...

  • Page 568

    Cargo area cover . . . . . . . . . . . . . . . . . . . . . . . 234 cargo area features . . . . . . . . . . . . . . . . . . . . . . 231 cargo compartment . . . . . . . . . . . . . . . . . . . . . . 231 light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 233 cargo light . . . . . . . ....

  • Page 569

    Coolant level . . . . . . . . . . . . . . . . . . . . . . . . . 506 disposal of used coolant . . . . . . . . . . . . . . . . 506 drain, flush, and refill . . . . . . . . . . . . . . . . . . 503 inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . 502 points to remember . . . . . . . . . ...

  • Page 570

    E-85 fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 429 electric remote mirrors . . . . . . . . . . . . . . . . . . . 110 electrical outlet, auxiliary (power outlet) . . . . . . 221 electronic brake control system . . . . . . . . . . . . . 381 anti-lock brake system . . . . . . . . ....

  • Page 571

    Oil synthetic . . . . . . . . . . . . . . . . . . . . . . . . . 491 overheating . . . . . . . . . . . . . . . . . . . . . . . . . . 462 starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 343 temperature gauge . . . . . . . . . . . . . . . . . . . . 257 engine oil viscosity . . . . . ...

  • Page 572

    Power steering . . . . . . . . . . . . . . . . . . . . . . . . 378 fluids, lubricants and genuine parts . . . . . . . . . . 534 fog light service . . . . . . . . . . . . . . . . . . . . . . . . 528 fog lights . . . . . . . . . . . . . . . . . . . . . . . . . . 250,528 folding rear seat . . . . . . ....

  • Page 573

    Gauges coolant temperature . . . . . . . . . . . . . . . . . . . 257 fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 256 speedometer . . . . . . . . . . . . . . . . . . . . . . . . . 255 tachometer . . . . . . . . . . . . . . . . . . . . . . . . . . 248 gear ranges . . . . . . . ....

  • Page 574

    Infant restraint . . . . . . . . . . . . . . . . . . . . . . . . 82,83 inflation pressure tires . . . . . . . . . . . . . . . . . . . . 404 information center, vehicle . . . . . . . . . . . . . . . . . 258 inside rearview mirror . . . . . . . . . . . . . . . . . . . 108 instrument cluster . . . . . ...

  • Page 575

    Light bulbs . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100,146 airbag . . . . . . . . . . . . . . . . . . . . . . 75,76,81,98,248 anti-lock . . . . . . . . . . . . . . . . . . . . . . . . . . . 255 automatic headlights...

  • Page 576

    Turn signal . . . . . . . . . . . . . . . . . . 100,146,528,530 vanity mirror . . . . . . . . . . . . . . . . . . . . . . . . . 111 loading vehicle . . . . . . . . . . . . . . . . . . . . . . . . . 436 tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 399 locks . . . . . . . . . . ...

  • Page 577

    Multi-function control lever . . . . . . . . . . . . . . . 146 new vehicle break-in period . . . . . . . . . . . . . . . . 95 occupant restraints . . . . . . . . . . . . . . . . . . . 48,74,78 occupant restraints (sedan) . . . . . . . . . . . 71,72,74,77 odometer . . . . . . . . . . . . . . . . . . ...

  • Page 578

    Parking brake . . . . . . . . . . . . . . . . . . . . . . . . . . 379 personal settings . . . . . . . . . . . . . . . . . . . . . . . . 280 pets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95 pets, transporting . . . . . . . . . . . . . . . . . . . . . . . . 95 phone, cellula...

  • Page 579

    Rear park sense system . . . . . . . . . . . . . . . . . . . 195 rear seat, folding . . . . . . . . . . . . . . . . . . . . . . . 137 rear window defroster . . . . . . . . . . . . . . . . . . . 238 rear window features . . . . . . . . . . . . . . . . . . . . 237 rear wiper/washer . . . . . . . . . ....

  • Page 580

    Schedule, maintenance . . . . . . . . . . . . . . . . . . . . 538 seat belt reminder . . . . . . . . . . . . . . . . . . . . . . . 65 seat belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52,98 adjustable upper shoulder anchorage . . . . . . . . 57 and pregnant women . . . . . . . . . ....

  • Page 581

    Shifting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 349 automatic transmission . . . . . . . . . . . . . . . . . 349 shoulder belts . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 side airbag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77 signals, turn . . ....

  • Page 582

    Supplemental restraint system - airbag . . . . . . . . 68 suspension, air . . . . . . . . . . . . . . . . . . . . . . . . . 365 sway control, trailer . . . . . . . . . . . . . . . . . . . . . 387 synthetic engine oil . . . . . . . . . . . . . . . . . . . . . . 491 system, remote starting . . . . . ....

  • Page 583

    Snow tires . . . . . . . . . . . . . . . . . . . . . . . . . . . 413 spare tire . . . . . . . . . . . . . . . . . . . . . . . . . . . 464 spinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . 409 tread wear indicators . . . . . . . . . . . . . . . . . . . 410 wheel mounting . . . . . . . ...

  • Page 584

    Uci connector . . . . . . . . . . . . . . . . . . . . . . . . . 313 uconnect™ (hands-free phone) . . . . . . . . . . . . . . 121 uniform tire quality grades . . . . . . . . . . . . . . . . 561 universal consumer interface (uci) connector . . . 313 universal transmitter . . . . . . . . . . . . . . . ...

  • Page 585

    Window fogging . . . . . . . . . . . . . . . . . . . . . . . . 334 windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 windshield defroster . . . . . . . . . . . . . . . . . . . 98,326 windshield washers . . . ...

  • Page 586

    291680.Ps 11jk72-126-aa chrysler 1" gutter 05/14/2010 06:18:00 vehicles sold in canada with respect to any vehicles sold in canada, the name chrysler group llc shall be deemed to be deleted and the name chrysler canada inc. Used in substitution therefore. Driving and alcohol drunken driving is one o...

  • Page 587

    Chrysler group llc 11wk741-126-ae fifth edition printing in u.S.A..