1. DL manuals
  2. Jeep
  3. Automobile
  4. 2012 Patriot Series
  5. Owner's Manual

Jeep 2012 Patriot Series Owner's Manual

Summary of 2012 Patriot Series

  • Page 1

    Patriot chrysler group llc o w n e r ’ s m a n u a l 2 0 12 p a t r io t 12mk74-126-aa first edition printed in u.S.A. 2 0 1 2 910344 patriot om cover.Indd 1 3/31/11 10:45 am.

  • Page 2

    Vehicles sold in canada with respect to any vehicles sold in canada, the name chrysler group llc shall be deemed to be deleted and the name chrysler canada inc. Used in substitution therefore. Driving and alcohol drunken driving is one of the most frequent causes of accidents. Your driving ability c...

  • Page 3: Table Of Contents

    Table of contents section page 1 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 things to know before starting your vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 3 understanding the featu...

  • Page 5: Introduction

    Introduction contents 䡵 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 䡵 rollover warning . . . . . . . . . . . . . . . . . . . . . . . 4 䡵 how to use this manual . . . . . . . . . . . . . . . . . . 5 䡵 warnings and cautions . . . . . . . . . . . . . . . . . . . 7 䡵 vehicle ide...

  • Page 6

    Introduction congratulations on selecting your new chrysler group llc vehicle. Be assured that it represents precision workmanship, distinctive styling, and high quality - all essentials that are traditional to our vehicles. This owner’s manual has been prepared with the assis- tance of service and ...

  • Page 7

    Control. Failure to operate this vehicle safely may result in a collision, rollover of the vehicle, and severe or fatal injury. Drive carefully. Failure to use the driver and passenger seat belts pro- vided is a major cause of severe or fatal injury. In fact, the u.S. Government notes that the unive...

  • Page 8

    6 introduction.

  • Page 9

    Warnings and cautions this owner’s manual contains warnings against op- erating procedures that could result in a collision or bodily injury. It also contains cautions against proce- dures that could result in damage to your vehicle. If you do not read this entire manual, you may miss important info...

  • Page 10

    Note: it is illegal to remove or alter the vin. Vehicle modifications/alterations warning! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a accident resulting in serious injury or death. Right front body vin location 8 introducti...

  • Page 11: Contents

    Things to know before starting your vehicle contents 䡵 a word about your keys . . . . . . . . . . . . . . . . . 12 ▫ ignition key removal . . . . . . . . . . . . . . . . . . 12 ▫ locking doors with a key . . . . . . . . . . . . . . 14 ▫ key-in-ignition reminder . . . . . . . . . . . . . . . 14 䡵 sen...

  • Page 12

    ▫ illuminated approach — if equipped . . . . . . . 21 ▫ to lock the doors and liftgate . . . . . . . . . . 22 ▫ sound horn with remote key lock . . . . . . . . 22 ▫ flash lights with remote key lock/unlock . . 23 ▫ using the panic alarm . . . . . . . . . . . . . . . . . 24 ▫ programming additional t...

  • Page 13

    ▫ automatic locking retractor mode (alr) — if equipped . . . . . . . . . . . . . . . . . . . . . . . . . 53 ▫ energy management feature . . . . . . . . . . . . . 54 ▫ seat belt pretensioners . . . . . . . . . . . . . . . . . 55 ▫ supplemental active head restraints (ahr) — if equipped . . . . . . . ...

  • Page 14

    A word about your keys the authorized dealer that sold you your new vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys. Ask your authorized dealer for these numbers and keep them in a safe place. Ignition key removal 1. Place the shift lever in...

  • Page 15

    Note: if you try to remove the key before you place the shift lever in park, the key may become trapped tem- porarily in the ignition switch cylinder. If this occurs, place the shift lever in park, rotate the key to the right slightly, then remove the key as described. If a malfunc- tion occurs, the...

  • Page 16

    Warning! (continued) • allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Chil- dren should be warned not to touch the parking brake, brake pedal or the shift lever. • do not leave the key fob in or near the ...

  • Page 17

    Sentry key 姞 the sentry key 威 immobilizer system prevents unauthor- ized vehicle operation by disabling the engine. The system does not need to be armed or activated. Operation is automatic, regardless of whether the vehicle is locked or unlocked. The system uses ignition keys that have an embedded ...

  • Page 18

    All of the keys provided with your new vehicle have been programmed to the vehicle electronics. Replacement keys note: only keys that are programmed to the vehicle electronics can be used to start and operate the vehicle. Once a sentry key 威 is programmed to a vehicle, it cannot be programmed to any...

  • Page 19

    2. Insert the first valid key into the ignition switch. Turn the ignition switch to the on/run position for at least three seconds, but no longer than 15 seconds. Then, turn the ignition switch to the lock position and remove the first key. 3. Insert the second valid key into the ignition switch. Tu...

  • Page 20

    • this device must accept any interference that may be received, including interference that may cause unde- sired operation. Vehicle security alarm — if equipped this vehicle security alarm monitors the doors, liftgate, and ignition switch for unauthorized operation. When the alarm is activated, th...

  • Page 21

    Rearming the system if something triggers the alarm, and no action is taken to disarm it, the vehicle security alarm will turn off the horn after three minutes, turn off all of the visual signals after 15 minutes, and then the vehicle security alarm will rearm itself. To disarm the system press unlo...

  • Page 22

    Remote keyless entry (rke) — if equipped this system allows you to lock or unlock the doors and liftgate or activate the panic alarm from distances up to approximately 66 ft (20 m) using a hand-held remote keyless entry (rke) transmitter. The rke transmitter does not need to be pointed at the vehicl...

  • Page 23

    • for vehicles not equipped with the evic, perform the following steps: 1. Press and hold the lock button on a programmed rke transmitter for at least 4 seconds, but no longer than 10 seconds. Then, press and hold the unlock button while still holding the lock button. 2. Release both buttons at the ...

  • Page 24

    To lock the doors and liftgate press and release the lock button on the rke transmit- ter to lock all doors and liftgate. The turn signal lights will flash and the horn will chirp to acknowledge the signal. Sound horn with remote key lock this feature will cause the horn to chirp when the doors are ...

  • Page 25

    Note: pressing the lock button on the rke transmit- ter while you are in the vehicle will activate the vehicle security alarm. Opening a door with the vehicle security alarm activated will cause the alarm to sound. Press the unlock button to deactivate the vehicle security alarm. Flash lights with r...

  • Page 26

    Alarm activated will cause the alarm to sound. Press the unlock button to deactivate the vehicle security alarm. Using the panic alarm to turn the panic alarm feature on or off, press and hold the panic button on the rke transmitter for at least one second and release. When the panic alarm is on, th...

  • Page 27

    If your rke transmitter fails to operate from a normal distance, check for these two conditions: 1. Weak battery in the rke transmitter. The expected life of a battery is five years. 2. Closeness to a radio transmitter such as a radio station tower, airport transmitter, military base, and some mobil...

  • Page 28

    3. To reassemble the rke transmitter case, snap the two halves together. Note: if the rke transmitter is equipped with a screw, reinstall and tighten the screw until snug. Remote starting system — if equipped this system uses the remote keyless entry (rke) transmitter to start the engine conve- nien...

  • Page 29

    Warning! • do not start or run an engine in a closed garage or confined area. Exhaust gas contains carbon mon- oxide (co) which is odorless and colorless. Car- bon monoxide is poisonous and can cause serious injury or death when inhaled. • keep remote keyless entry (rke) transmitters away from child...

  • Page 30

    • for security, power window and power sunroof op- eration (if equipped) are disabled when the vehicle is in the remote start mode. • if your power door locks were unlocked, remote start will automatically lock the doors. • the engine can be started two consecutive times (two 15-minute cycles) with ...

  • Page 31

    To exit remote start mode and drive the vehicle before the end of the 15-minute cycle, press and release the unlock button on the rke transmitter to unlock the doors and disarm the vehicle security alarm (if equipped). Then, insert the key into the ignition switch and turn the switch to the on/run p...

  • Page 32

    Warning! (continued) • before exiting a vehicle, always apply the parking brake, shift the transmission into park, and re- move the key fob from the ignition. When leaving the vehicle, always lock your vehicle. • never leave children alone in a vehicle, or with access to an unlocked vehicle. • allow...

  • Page 33

    Auto lock doors — if equipped the auto door lock feature default condition is enabled. When enabled, the door locks will lock automatically when the vehicle’s speed exceeds 15 mph (24 km/h). The auto door lock feature can be enabled or disabled by your authorized dealer. Please see your authorized d...

  • Page 34

    2. Within 15 seconds, cycle the ignition switch between lock and on/run and then back to lock four times ending up in the lock position (do not start the engine). 3. Within 30 seconds, press the power door lock switch to lock the doors. 4. A single chime will indicate the completion of the programmi...

  • Page 35

    Equipped/ personal settings (customer-programmable features)” in “understanding your instrument panel” for further information. • for vehicles not equipped with the evic, perform the following procedure: 1. Close all doors and place the key in the ignition. 2. Within 15 seconds, cycle the ignition s...

  • Page 36

    3. Repeat steps 1 and 2 for the opposite rear door. Warning! Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child-protection locks are engaged. Child-protection door lock location child-protection door lock function 34 thi...

  • Page 37

    Note: for emergency exit with the system engaged, move the lock knob up (unlocked position), roll down the window and open the door with the outside door handle. Power windows — if equipped power window switches the window controls on the driver’s door trim panel control all the door windows. There ...

  • Page 38

    Warning! Never leave children in a vehicle with the key in the ignition switch. Occupants, particularly unattended children, can become entrapped by the windows while operating the power window switches. Such entrapment may result in serious injury or death. Auto-down the driver’s door window switch...

  • Page 39

    Window lockout switch the window lockout switch on the driver’s door allows you to disable the window control on the other doors. To disable the window controls on the other doors, press the window lockout switch. To enable the window con- trols, press the window lockout switch a second time. Liftga...

  • Page 40

    Once unlocked, the liftgate can be opened or closed without using the key. To open the liftgate, squeeze the liftgate release and pull the liftgate open with one fluid motion. Note: • in the event of a power malfunction, or the rke transmitter is inoperative, insert the key into the liftgate lock cy...

  • Page 41

    Warning! (continued) • if you are required to drive with the liftgate open, make sure that all windows are closed, and the climate control blower switch is set at high speed. Do not use the recirculation mode. Gas props support the liftgate in the open position. However, because the gas pressure dro...

  • Page 42

    Seat belt webbing into position by extending the belt all the way out and then adjusting the belt to the desired length to restrain a child seat or secure a large item in a seat — if equipped please pay close attention to the information in this section. It tells you how to use your restraint system...

  • Page 43

    Ride properly buckled up in the rear seat. Never allow children to slide the shoulder belt behind them or under their arm. If a child from 1 to 12 years old (not in a rear facing child seat) must ride in the front passenger seat, move the seat as far back as possible and use the proper child restrai...

  • Page 44

    Warning! (continued) • being too close to the steering wheel or instrument panel during advanced front air bag deployment could cause serious injury, including death. Air bags need room to inflate. Sit back, comfortably extending your arms to reach the steering wheel or instrument panel. • supplemen...

  • Page 45

    The belt webbing retractor is designed to lock during very sudden stops or accidents. This feature allows the shoulder part of the belt to move freely with you under normal conditions. However, in an accident the belt will lock and reduce the risk of you striking the inside of the vehicle or being t...

  • Page 46

    Lap/shoulder belt operating instructions 1. Enter the vehicle and close the door. Sit back and adjust the seat. 2. The seat belt latch plate is along side the pillar near the back of your seat. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to a...

  • Page 47

    3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” warning! • a belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your bel...

  • Page 48

    Warning! (continued) • a belt that is worn under your arm is dangerous. Your body could strike the inside surfaces of the vehicle in an accident, increasing head and neck injury. A belt worn under the arm can cause internal injuries. Ribs aren’t as strong as shoulder bones. Wear the belt over your s...

  • Page 49

    Warning! • a lap belt worn too high can increase the risk of internal injury in an accident. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as possible and keep it snug. • a twisted belt will not protect you properly. In a collis...

  • Page 50

    Adjustable upper shoulder belt anchorage in the front seat, the shoulder belt can be adjusted upward or downward to position the belt away from your neck. Push the anchorage button to release the anchorage, and move it up or down to the position that fits you best. Note: the adjustable upper shoulde...

  • Page 51

    In the rear seat, move toward the center of the seat to position the belt away from your neck. Second row center lap/shoulder belt operating instructions the second row center lap/shoulder belt features a three-point seat belt with a mini-latch and buckle, which allows the shoulder belt to detach fr...

  • Page 52

    3. Route the shoulder belt to the inside of the right head restraint. 4. When the belt is long enough to fit, insert the mini- latch plate into the mini-buckle until you hear a “click.” 5. Sit back in the seat. Slide the regular latch plate up the webbing as far as necessary to allow the belt to go ...

  • Page 53

    7. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt if it is too tight, pull on the lap belt. A snug belt reduces the risk of sliding under the belt in an accident. 8. Position the shoulder bel...

  • Page 54

    10. To disengage the mini-latch from the mini-buckle for storage, insert the regular latch plate into the black button on the top of the mini-buckle. The belt will automatically retract to its stowed position. If necessary, slide the latch plate down the webbing to allow the belt to retract fully. I...

  • Page 55

    Driver center passenger first row n/a n/a alr second row alr alr alr • n/a — not applicable • alr — automatic locking retractor if the passenger seating position is equipped with an alr and is being used for normal usage: only pull the belt webbing out far enough to comfortably wrap around the occup...

  • Page 56

    How to engage the automatic locking mode 1. Buckle the combination lap and shoulder belt. 2. Grasp the shoulder portion and pull downward until the entire belt is extracted. 3. Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in t...

  • Page 57

    Seat belt pretensioners the seat belts for both front seating positions are equipped with pretensioning devices that are designed to remove slack from the seat belt in the event of an accident. These devices may improve the performance of the seat belt by assuring that the belt is tight about the oc...

  • Page 58

    When ahrs deploy during a rear impact, the front half of the head restraint extends forward to minimize the gap between the back of the occupant’s head and the ahr. This system is designed to help prevent or reduce the extent of injuries to the driver and front passenger in certain types of rear imp...

  • Page 59

    Caution! All occupants, including the driver, should not oper- ate a vehicle or sit in a vehicle’s seat until the head restraints are placed in their proper positions in order to minimize the risk of neck injury in the event of an accident. Note: for more information on properly adjusting and positi...

  • Page 60

    3. Pull down then rearward towards the rear of the vehicle then down to engage the locking mechanism. 1 — downward movement 2 — rearward movement 3 — final downward movement to engage locking mechanism 58 things to know before starting your vehicle.

  • Page 61

    4. The ahr front soft foam and trim half should lock into the back decorative plastic half. Note: • if you have difficulties or problems resetting the active head restraints, see an authorized dealer. • for safety reasons, have the active head restraints checked by a qualified specialist at an autho...

  • Page 62

    Unbuckled while traveling at speeds greater than 5 mph (8 km/h), beltalert 威 will provide both audio and visual notification. The front passenger seat beltalert 威 is not active when the front passenger seat is unoccupied. Beltalert 威 may be triggered when an animal or heavy object is on the front pa...

  • Page 63

    Seat belts and pregnant women we recommend that pregnant women use the seat belts throughout their pregnancy. Keeping the mother safe is the best way to keep the baby safe. Pregnant women should wear the lap part of the belt across the thighs and as snug across the hips as possible. Keep the belt lo...

  • Page 64

    The advanced front air bags have a multistage inflator design. This allows the air bag to have different rates of inflation that are based on the severity and type of collision. This vehicle may be equipped with driver and/or front passenger seat track position sensors that may adjust the inflation ...

  • Page 65

    • instrument panel • knee impact bolster • driver advanced front air bag • passenger advanced front air bag • supplemental seat-mounted side air bags (sab) • supplemental side air bag inflatable curtains (sabic) • front and side impact sensors • front seat belt pretensioners, seat belt buckle switch...

  • Page 66

    Warning! • no objects should be placed over or near the air bag on the instrument panel, because any such objects could cause harm if the vehicle is in a collision severe enough to cause the air bag to inflate. • do not put anything on or around the air bag covers or attempt to open them manually. Y...

  • Page 67

    When the air bag deploys, it opens the seam between the front and side of the seat’s trim cover. Each air bag deploys independently; a left side impact deploys the left air bag only and a right-side impact deploys the right air bag only. Supplemental side air bag inflatable curtain (sabic) sabic air...

  • Page 68

    • being too close to the supplemental side air bag inflatable curtain and/or seat-mounted side air bag during deployment could cause you to be severely injured or killed. The system includes side impact sensors that are cali- brated to deploy the side air bags during impacts that require air bag occ...

  • Page 69

    Along with seat belts and pretensioners, advanced front air bags work with the knee bolsters to provide im- proved protection for the driver and front passenger. Side air bags also work with seat belts to improve occupant protection. Air bag deployment sensors and controls occupant restraint control...

  • Page 70

    Because air bag sensors measure vehicle deceleration over time, vehicle speed and damage by themselves are not good indicators of whether or not an air bag should have deployed. Seat belts are necessary for your protection in all acci- dents, and also are needed to help keep you in position, away fr...

  • Page 71

    Warning! Ignoring the air bag warning light in your instru- ment panel could mean you won’t have the air bags to protect you in a collision. If the light does not come on as a bulb check when the ignition is first turned on, stays on after you start the vehicle, or if it comes on as you drive, have ...

  • Page 72

    Based on the severity and type of collision, the side air bag inflator on the crash side of the vehicle may be triggered, releasing a quantity of non-toxic gas. The inflating sab exits through the seat seam into the space between the occupant and the door. The sab fully inflate in about 10 milliseco...

  • Page 73

    Front and side impact sensors in front and side impacts, impact sensors can aid the orc in determining appropriate response to impact events. Enhanced accident response system in the event of an impact causing air bag deployment, if the communication network remains intact, and the power remains int...

  • Page 74

    If you do have a collision, which deploys the air bags, any or all of the following may occur: • the nylon air bag material may sometimes cause abrasions and/or skin reddening to the driver and front passenger as the air bags deploy and unfold. The abrasions are similar to friction rope burns or tho...

  • Page 75

    Maintaining your air bag system warning! • modifications to any part of the air bag system could cause it to fail when you need it. You could be injured if the air bag system is not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the s...

  • Page 76

    Air bag warning light you will want to have the air bags ready to inflate for your protection in a collision. The air bag warning light monitors the internal circuits and interconnecting wiring associated with air bag system electrical components. While the air bag system is designed to be maintenan...

  • Page 77

    • whether or not the driver and passenger safety belts were buckled/fastened; • how far (if at all) the driver was depressing the accelerator and/or brake pedal; and, • how fast the vehicle was traveling. These data can help provide a better understanding of the circumstances in which crashes and in...

  • Page 78

    Warning! In a collision, an unrestrained child, even a tiny baby, can become a projectile inside the vehicle. The force required to hold even an infant on your lap could become so great that you could not hold the child, no matter how strong you are. The child and others could be badly injured. Any ...

  • Page 79

    Warning! Rearward-facing child seats must never be used in the front seat of a vehicle with the front passenger air bag unless the air bag is turned off. An air bag deployment could cause severe injury or death to infants in this position. Older children and child restraints children who are two yea...

  • Page 80

    Warning! • improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the manufacturer’s directions ex- actly when installing an infant or child restraint. • a rearward-facing child restraint shoul...

  • Page 81

    Retractor. For additional information on alr, refer to “automatic locking mode”. The chart below defines the seating positions with an automatic locking retractor (alr) or a cinching latch plate. Driver center passenger crs lock crs lock crs lock first row n/a n/a alr second row alr alr alr • n/a — ...

  • Page 82

    Around, and insert the latch plate into the buckle again. If you still can’t make the child restraint secure, try a different seating position. • buckle the child into the seat according to the child restraint manufacturer’s directions. Warning! When your child restraint is not in use, secure it in ...

  • Page 83

    Webbing-mounted lower attachments. Child seats with fixed lower attachments must be installed in the out- board positions only. Regardless of the specific type of lower attachment, never install latch-compatible child seats such that two seats share a common lower anchor- age. If you are installing ...

  • Page 84

    Provide add-on tether strap kits for some of their older products. Tether anchorage kits are also available for most older vehicles. Because the lower anchorages are to be introduced to passenger carrying vehicles over a period of years, child restraint systems having attachments for those anchor- a...

  • Page 85

    In general, you will first loosen the adjusters on the lower and tether straps so that you can attach the hook or connector to the lower and tether anchorages more easily. The tether strap should be routed over the center of the head restraint and attached to the tether anchor on the rear of the sea...

  • Page 86

    Transporting pets air bags deploying in the front seat could harm your pet. An unrestrained pet will be thrown about and possibly injured, or injure a passenger during panic braking or in an accident. Pets should be restrained in the rear seat in pet harnesses or pet carriers that are secured by sea...

  • Page 87

    Safety tips transporting passengers never transport passengers in the cargo area. Warning! • do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death. • it is extremely dangerous to ride in a cargo area, inside or outside of a v...

  • Page 88

    Warning! (continued) • if it is necessary to sit in a parked vehicle with the engine running, adjust your heating or cooling controls to force outside air into the vehicle. Set the blower at high speed. The best protection against carbon monoxide entry into the vehicle body is a properly maintained ...

  • Page 89

    Defroster check operation by selecting the defrost mode and place the blower control on high speed. You should be able to feel the air directed against the windshield. See your authorized dealer for service if your defroster is inoperable. Floor mat safety information always use floor mats designed ...

  • Page 90

    Warning! (continued) • always make sure that objects cannot fall into the driver footwell while the vehicle is moving. Ob- jects can become trapped under the brake pedal and accelerator pedal causing a loss of vehicle control. • if required, mounting posts must be properly installed, if not equipped...

  • Page 91: Contents

    Understanding the features of your vehicle contents 䡵 mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94 ▫ inside day/night mirror . . . . . . . . . . . . . . . . 94 ▫ automatic dimming mirror — if equipped . . . 95 ▫ power mirrors . . . . . . . . . . . . . . . . . . . . . . . 96...

  • Page 92

    䡵 voice command — if equipped . . . . . . . . . . . 129 ▫ voice command system operation . . . . . . . . 129 ▫ commands . . . . . . . . . . . . . . . . . . . . . . . . 130 ▫ voice training . . . . . . . . . . . . . . . . . . . . . . 134 䡵 seats . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

  • Page 93

    ▫ instrument panel dimming . . . . . . . . . . . . . 152 ▫ map/reading lights . . . . . . . . . . . . . . . . . . 153 䡵 windshield wipers and washers . . . . . . . . . . 154 ▫ windshield wiper operation . . . . . . . . . . . . 155 ▫ intermittent wiper system . . . . . . . . . . . . . . 155 ▫ windshi...

  • Page 94

    䡵 power sunroof — if equipped . . . . . . . . . . . . 170 ▫ opening sunroof — express . . . . . . . . . . . . 171 ▫ opening sunroof — manual mode . . . . . . . . 171 ▫ closing sunroof — express . . . . . . . . . . . . . 171 ▫ closing sunroof — manual mode . . . . . . . . 171 ▫ pinch protect feature ...

  • Page 95

    ▫ cargo tie-down loops . . . . . . . . . . . . . . . . 185 ▫ fold down speakers — if equipped . . . . . . . 187 䡵 rear window features . . . . . . . . . . . . . . . . . . 187 ▫ rear window wiper/washer . . . . . . . . . . . . 187 ▫ rear window defroster . . . . . . . . . . . . . . . . 188 䡵 roof lug...

  • Page 96

    Mirrors inside day/night mirror a two-point pivot system allows for horizontal and vertical mirror adjustment. Adjust the mirror to center on the view through the rear window. Headlight glare can be reduced by moving the small control under the mirror to the night position (toward the rear of vehicl...

  • Page 97

    Automatic dimming mirror — if equipped this mirror automatically adjusts for headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light to the left of the button will illuminate to indicate when the dimming feature is activa...

  • Page 98

    Power mirrors the power mirror controls are located on the driver’s door trim panel. To adjust a mirror, turn the control wand toward the left or right mirror positions indicated. Tilt the control wand in the direction you want the mirror to move. When you are finished adjusting the mirror, turn the...

  • Page 99

    Outside mirror — driver side adjust the flat outside mirror to center on the adjacent lane of traffic with a slight overlap of the view obtained on the inside mirror. Outside mirror — passenger side adjust the convex outside mirror to center on the adja- cent lane of traffic with a slight overlap of...

  • Page 100

    Warning! Vehicles and other objects seen in the passenger side convex mirror will look smaller and farther away than they really are. Relying too much on your passenger side mirror could cause you to collide with another vehicle or other object. Use your inside mirror when judging the size or distan...

  • Page 101

    Vanity mirrors — if equipped to use the mirror, pull the sun visor down and rotate the mirror cover upward. Sun visor sliding feature the sun visors may be pulled out to provide extended coverage of the side glass. Uconnect™ phone — if equipped uconnect™ phone is a voice-activated, hands-free, in- v...

  • Page 102

    • www.Jeep.Com/uconnect • or call 1–877–855–8400 uconnect™ phone allows you to transfer calls between the system and your mobile phone as you enter or exit your vehicle and enables you to mute the system’s microphone for private conversation. The uconnect™ phone is driven through your bluetooth 威 “h...

  • Page 103

    Voice command button actual button location may vary with the ra- dio. The individual buttons are described in the “operation” section. The uconnect™ phone can be used with any hands-free profile certified bluetooth 威 mobile phone. See the uconnect™ website for supported phones. Refer to your mobile...

  • Page 104

    Example, you can use the compound form voice command “phonebook new entry”, or you can break the compound form command into two voice com- mands: “phonebook” and “new entry”. Please re- member, the uconnect™ phone works best when you talk in a normal conversational tone, as if speaking to someone si...

  • Page 105

    • when prompted, after the beep, say “pair a device” and follow the audible prompts. • you will be asked to say a four-digit personal identi- fication number (pin), which you will later need to enter into your mobile phone. You can enter any four-digit pin. You will not need to remember this pin aft...

  • Page 106

    • the uconnect™ phone will confirm the phone number and then dial. The number will appear in the display of certain radios. Call by saying a name • press the button to begin. • after the “ready” prompt and the following beep, say “call”. • the system will prompt you to say the name of the person you...

  • Page 107

    • when prompted, enter the number designation (e.G., “home”, “work”, “mobile”, or “other”). This will allow you to store multiple numbers for each phone- book entry, if desired. • when prompted, recite the phone number for the phonebook entry that you are adding. After you are finished adding an ent...

  • Page 108

    • depending on the maximum number of entries down- loaded, there may be a short delay before the latest downloaded names can be used. Until then, if avail- able, the previously downloaded phonebook is avail- able for use. • only the phonebook of the currently connected mobile phone is accessible. • ...

  • Page 109

    After you are finished editing an entry in the phonebook, you will be given the opportunity to edit another entry in the phonebook, call the number you just edited, or return to the main menu. “phonebook edit entry” can be used to add another phone number to a name entry that already exists in the p...

  • Page 110

    Delete/erase “all” uconnect™ phonebook entries • press the button to begin. • after the “ready” prompt and the following beep, say “phonebook erase all”. • the uconnect™ phone will ask you to verify that you wish to delete all the entries from the phonebook. • after confirmation, the phonebook entri...

  • Page 111

    Phone call features the following features can be accessed through the uconnect™ phone if the feature(s) are available on your mobile service plan. For example, if your mobile service plan provides three-way calling, this feature can be accessed through the uconnect™ phone. Check with your mobile se...

  • Page 112

    In progress. To go back to the first call, refer to “toggling between calls” in this section. To combine two calls, refer to “conference call” in this section. Place/retrieve a call from hold to put a call on hold, press the button until you hear a single beep. This indicates that the call is on hol...

  • Page 113

    Call termination to end a call in progress, momentarily press the button. Only the active call(s) will be terminated and if there is a call on hold, it will become the new active call. If the active call is terminated by the phone far end, a call on hold may not become active automatically. This is ...

  • Page 114

    Uconnect™ phone features language selection to change the language that the uconnect™ phone is using: • press the button to begin. • after the “ready” prompt and the following beep, say the name of the language you wish to switch to english, espanol, or francais. • continue to follow the system prom...

  • Page 115

    Canada and 060 for mexico). The number dialed may not be applicable with the available mobile service and area. • if supported, this number may be programmable on some systems. To do this, press the button and say “setup”, followed by “emergency”. • the uconnect™ phone does slightly lower your chanc...

  • Page 116

    Paging to learn how to page, refer to “working with automated systems”. Paging works properly except for pagers of certain companies, which time out a little too soon to work properly with the uconnect™ phone. Voice mail calling to learn how to access your voice mail, refer to “working with automate...

  • Page 117

    The uconnect™ phone will then send the corresponding phone number associated with the phonebook entry, as tones over the phone. Note: • you may not hear all of the tones due to mobile phone network configurations. This is normal. • some paging and voice mail systems have system time out settings tha...

  • Page 118

    Dialing using the mobile phone keypad you can dial a phone number with your mobile phone keypad and still use the uconnect™ phone (while dialing via the mobile phone keypad, the user must exercise caution and take precautionary safety measures). By dialing a number with your paired bluetooth 威 mobil...

  • Page 119

    From your uconnect™ phone paired mobile phone to the uconnect™ phone or vice versa, press the button and say “transfer call”. Connect or disconnect link between the uconnect™ phone and mobile phone your mobile phone can be paired with many different electronic devices, but can only be actively “conn...

  • Page 120

    • the selected phone will be used for the next phone call. If the selected phone is not available, the uconnect™ phone will return to using the highest priority phone present in or near (approximately within 30 ft (9 m)) the vehicle. Delete uconnect™ phone paired mobile phones • press the button to ...

  • Page 121

    You can either press the uconnect™ phone button to restore the factory setting or repeat the words and phrases when prompted by the uconnect™ phone. For best results, the voice training session should be com- pleted when the vehicle is parked with the engine running, all windows closed, and the blow...

  • Page 122

    • fully closed windows, • dry weather condition. • even though the system is designed for users speaking in north american english, french, and spanish ac- cents, the system may not always work for some. • when navigating through an automated system such as voice mail, or when sending a page, at the...

  • Page 123

    • fully closed windows, • dry weather conditions, and • operation from the driver’s seat. • performance, such as audio clarity, echo, and loudness to a large degree rely on the phone and network, and not the uconnect™ phone. • echo at the phone far end can sometimes be reduced by lowering the in-veh...

  • Page 124

    Send messages: you can send messages using uconnect™ phone. To send a new message: • press the button. • after the “ready” prompt and the following beep, say “sms send” or “send message.” • you can either say the message you wish to send or say “list messages.” there are 20 preset messages. To send ...

  • Page 125

    16. Can this wait? 17. Bye for now 18. When can we meet 19. Send number to call 20. Start without me turn sms incoming announcement on/off turning the sms incoming announcement off will stop the system from announcing the new incoming mes- sages. • press the button. • after the “ready” prompt and th...

  • Page 126

    124 understanding the features of your vehicle.

  • Page 127

    3 understanding the features of your vehicle 125.

  • Page 128

    126 understanding the features of your vehicle.

  • Page 129

    Voice commands primary alternate(s) zero one two three four five six seven eight nine star (*) plus (+) pound (#) add location all voice commands primary alternate(s) call cancel confirmation prompts continue delete dial download edit emergency english erase all espanol francais help home 3 understa...

  • Page 130

    Voice commands primary alternate(s) language list names list phones mobile mute mute off new entry no other pair a phone phone pairing pairing phonebook phone book previous record again redial voice commands primary alternate(s) return to main menu return or main menu select phone select send set up...

  • Page 131

    General information this device complies with part 15 of the fcc rules and rss 210 of industry canada. Operation is subject to the following conditions: • changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment....

  • Page 132

    If you ever wish to interrupt the system while it lists options, press the voice command button, listen for the beep, and say your command. Pressing the voice command button while the system is speaking is known as “barging in.” the system will be interrupted, and after the beep, you can add or chan...

  • Page 133

    3. Use the on/off volume rotary knob to adjust the volume to a comfortable level while the voice command system is speaking. Please note the volume setting for voice command is different than the audio system. Main menu start a dialogue by pressing the voice command button. You may say “main menu” t...

  • Page 134

    • “menu radio” (to switch to the radio menu) • “main menu” (to switch to the main menu) satellite radio to switch to satellite radio mode, say “sat” or “satellite radio”. In this mode, you may say the following com- mands: • “channel number” (to change the channel by its spoken number) • “next chann...

  • Page 135

    − “continue” (to continue recording) − “delete” (to delete the recording) • “play memos” (to play previously recorded memos) — during the playback you may press the voice command button to stop playing memos. You proceed by saying one of the following commands: − “repeat” (to repeat a memo) − “next”...

  • Page 136

    Voice training for users experiencing difficulty with the system recog- nizing their voice commands or numbers the uconnect™ voice “voice training” feature may be used. 1. Press the voice command button, say “system setup” and once you are in that menu then say “voice training.” this will train your...

  • Page 137

    Power seats — if equipped some models may be equipped with a power driver’s seat. The power seat switch is located on the outboard side of the seat near the floor. Use the switch to move the seat up, down, forward, rearward, or to tilt the seat. Warning! • adjusting a seat while driving may be dange...

  • Page 138

    Adjusting the seat forward or rearward the seat can be adjusted both forward and rearward. Push the seat switch forward or rearward, the seat will move in the direction of the switch. Release the switch when you have reached the desired position. Adjusting the seat up or down the height of the seats...

  • Page 139

    If high-level heating is selected, the system automati- cally switches to low-level heating and turns one indi- cator light off after a maximum of 60 minutes of continuous operation. It will turn the heater and the remaining indicator light off after an a maximum of 45 minutes of continuous operatio...

  • Page 140

    While sitting in the seat, lift up on the bar and move the seat forward or rearward. Release the bar once you have reached the desired position. Then, using body pressure, move forward and rearward on the seat to be sure that the seat adjusters have latched. Warning! • adjusting a seat while driving...

  • Page 141

    Manual seat height adjustment — if equipped the driver’s seat height can be raised or lowered by using a lever, located on the outboard side of the seat. Pull upward on the lever to raise the seat height or push downward on the lever to lower the seat height. Manual lumbar — if equipped the lumbar a...

  • Page 142

    Driver’s seatback recline to adjust the seatback, lift the lever located on the outboard side of the seat, lean back to the desired angle and release the lever. To return the seatback, lift the lever, lean forward and release the lever. Warning! Do not ride with the seatback reclined so that the sho...

  • Page 143

    Fold-flat front passenger seat lever front passenger seat folded flat 3 understanding the features of your vehicle 141.

  • Page 144

    Head restraints head restraints are designed to reduce the risk of injury by restricting head movement in the event of a rear impact. Head restraints should be adjusted so that the top of the head restraint is located above the top of your ear. Warning! The head restraints for all occupants must be ...

  • Page 145

    To raise the head restraint, pull upward on the head restraint. To lower the head restraint, press the push button, located at the base of the head restraint, and push downward on the head restraint. For comfort the active head restraints can be tilted forward and backward. To tilt the head restrain...

  • Page 146

    Note: • the head restraints should only be removed by quali- fied technicians, for service purposes only. If either of the head restraints require removal, see your autho- rized dealer. • in the event of deployment of an active head re- straint, refer to “occupant restraints/resetting active head re...

  • Page 147

    Warning! (continued) • active head restraints may be deployed if they are struck by an object such as a hand, foot or loose cargo. To avoid accidental deployment of the ac- tive head restraint ensure that all cargo is se- cured, as loose cargo could contact the active head restraint during sudden st...

  • Page 148

    To raise the seatback, pull the strap forward and lift the seatback into its upright position. Warning! Be certain that the seatback is securely locked into position. If the seatback is not securely locked into position the seat will not provide the proper stability for child seats and/or passengers...

  • Page 149

    Warning! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt and be seriously or even fatally injured. Use the recliner only with the vehicle is parked. To open and close the hood to open the hoo...

  • Page 150

    2. Move the safety catch located under the front edge of the hood, near the center and raise the hood. Lift the hood prop rod, clipped to the right side (left side facing hood) of the engine compartment, to secure the hood in the open position. Place the hood prop at the location stamped into the in...

  • Page 151

    Caution! To prevent possible damage, do not slam the hood to close it. Lower the hood until it is open approxi- mately 8 in (20 cm) and then drop it. This should secure both latches. Never drive your vehicle unless the hood is fully closed, with both latches engaged. Warning! Be sure the hood is ful...

  • Page 152

    Headlights and parking lights turn the end of the multifunction lever to the first detent to turn on the parking lights. Turn the end of the lever to the second detent to turn on the headlights. Daytime running lights — if equipped the high beam lights will come on as daytime running lights (drl) at...

  • Page 153

    Note: the fog lights will only operate with the head- lights on low beam. Selecting high beam headlights will turn off the fog lights. Turn signals move the multifunction lever up or down and the arrows on each side of the instrument cluster flash to show proper operation of the front and rear turn ...

  • Page 154

    Light bulb. If an indicator fails to light when the lever is moved, it would suggest that the indicator bulb is defective. Lane change assist tap the lever up or down once, without moving beyond the detent, and the turn signal (right or left) will flash three times then automatically turn off. High/...

  • Page 155

    Map/reading lights these lights are mounted between the sun visors above the rear view mirror. Each light is turned on by pressing the button. Press the button a second time to turn the light off. The lights also come on when a door is opened or the dimmer control is turned fully upward, past the se...

  • Page 156

    Windshield wipers and washers the windshield wiper/washer control lever is located on the right side of the steering column. The front wipers are operated by rotating a switch, located on the end of the lever. For information on the rear wiper/washer, refer to “rear window fea- tures” in “understand...

  • Page 157

    Windshield wiper operation rotate the end of the lever upward to the second detent past the intermittent settings for low-speed wiper opera- tion. Rotate the end of the lever upward to the third detent past the intermittent settings for high-speed wiper opera- tion. Intermittent wiper system use the...

  • Page 158

    Downward (counterclockwise) to increase the delay time. The delay can be regulated from a maximum of approxi- mately 18 seconds between cycles, to a cycle every second. Note: the wiper delay times depend on vehicle speed. If the vehicle is moving less than 10 mph (16 km/h), delay times will be doubl...

  • Page 159

    Tilt steering column this feature allows you to tilt the steering column upward or downward. The tilt control handle is located on the left side of the steering column, below the turn signal lever. Push down on the lever to unlock the steering column. With one hand firmly on the steering wheel, move...

  • Page 160

    Warning! Do not adjust the steering column while driving. Adjusting the steering column while driving or driv- ing with the steering column unlocked, could cause the driver to lose control of the vehicle. Be sure the steering column is locked before driving your ve- hicle. Failure to follow this war...

  • Page 161

    System can be reactivated by pushing the electronic speed control on/off button and resetting the desired vehicle set speed. To activate push the on/off button. The cruise indicator light in the instrument cluster will illuminate. To turn the system off, push the on/off button a second time. The cru...

  • Page 162

    To resume speed to resume a previously set speed, push the res (+) button and release. Resume can be used at any speed above 20 mph (32 km/h). To vary the speed setting when the electronic speed control is set, you can in- crease speed by pushing the res (+) button. If the button is continually pres...

  • Page 163

    On steep hills, a greater speed loss or gain may occur so it may be preferable to drive without electronic speed control. Warning! Electronic speed control can be dangerous where the system cannot maintain a constant speed. Your ve- hicle could go too fast for the conditions, and you could lose cont...

  • Page 164

    Note: homelink 威 is disabled when the vehicle secu- rity alarm is active. Before you begin programming homelink 姞 be sure that your vehicle is parked outside of the garage before you begin programming. For more efficient programming and accurate transmis- sion of the radio-frequency signal it is rec...

  • Page 165

    Note: • erasing all channels should only be performed when programming homelink 威 for the first time. Do not erase channels when programming additional buttons. • if you have any problems, or require assistance, please call toll-free 1–800–355–3515 or, on the internet at www.Homelink.Com for informa...

  • Page 166

    3. Simultaneously press and hold both the homelink 威 button you want to program and the hand-held transmit- ter button. 4. Continue to hold both buttons and observe the indi- cator light. The homelink 威 indicator will flash slowly and then rapidly after homelink 威 has received the fre- quency signal...

  • Page 167

    2. Press and hold the desired homelink 威 button until the indicator light begins to flash after 20 seconds. Do not release the button. 3. Without releasing the button proceed with “program- ming a rolling code” step 2 and follow all remaining steps. Programming a non-rolling code for programming gar...

  • Page 168

    Reprogramming a single homelink 威 button to reprogram a channel that has been previously trained, follow these steps: 1. Turn the ignition switch to the on/run position. 2. Press and hold the desired homelink 威 button until the indicator light begins to flash after 20 seconds. Do not release the but...

  • Page 169

    4. Watch for the homelink 威 indicator to change flash rates. When it changes, it is programmed. It may take up to 30 seconds or longer in rare cases. The garage door may open and close while you are programming. 5. Press and hold the programmed homelink 威 button and observe the indicator light. • if...

  • Page 170

    Security it is advised to erase all channels before you sell or turn in your vehicle. To do this, press and hold the two outside buttons for 20 seconds until the red indicator flashes. Note that all channels will be erased. Individual channels cannot be erased. The homelink 威 universal transceiver i...

  • Page 171

    Warning! • your motorized door or gate will open and close while you are programming the universal trans- ceiver. Do not program the transceiver if people, pets or other objects are in the path of the door or gate. Only use this transceiver with a garage door opener that has a “stop and reverse” fea...

  • Page 172

    Power sunroof — if equipped the power sunroof switch is located in the reading light. Warning! • never leave children in a vehicle with the key in the ignition switch. Occupants, particularly unat- tended children, can become entrapped by the power sunroof while operating the power sunroof switch. S...

  • Page 173

    Opening sunroof — express press the switch rearward and release it within one-half second and the sunroof will open automatically from any position. The sunroof will open fully and stop automati- cally. This is called “express open”. During express open operation, any movement of the sunroof switch ...

  • Page 174

    Pinch protect feature this feature will detect an obstruction in the opening of the sunroof during express close operation. If an ob- struction in the path of the sunroof is detected, the sunroof will automatically retract. Remove the obstruc- tion if this occurs. Next, press the switch forward and ...

  • Page 175

    Ignition off operation for vehicles not equipped with the electronic vehicle information center (evic), the power sunroof switch will remain active for 45 seconds after the ignition switch is turned to the lock position. Opening either front door will cancel this feature. For vehicles equipped with ...

  • Page 176

    Note: to ensure proper operation a mopar 威 knob and element must be used. Caution! • do not exceed the maximum power of 160 watts (13 amps) at 12 volts. If the 160 watt (13 amp) power rating is exceeded the fuse protecting the system will need to be replaced. • power outlets are designed for accesso...

  • Page 177

    Warning! To avoid serious injury or death: • only devices designed for use in this type of outlet should be inserted into any 12 volt outlet. • do not touch with wet hands. • close the lid when not in use and while driving the vehicle. • if this outlet is mishandled, it may cause an electric shock a...

  • Page 178

    Power inverter — if equipped a 115 volt (150 watt) ac power inverter is located on the front of the center console for added convenience. This outlet can power cellular phones, electronics and other low power devices requiring power up to 150 watts. Certain high-end video games, such as playstation3...

  • Page 179

    Warning! To avoid serious injury or death: • do not use a three-prong adaptor. • do not insert any objects into the receptacles. • do not touch with wet hands. • close the lid when not in use. • if this outlet is mishandled, it may cause an electric shock and failure. Caution! • many accessories tha...

  • Page 180

    Cupholders your vehicle is equipped with four cupholders. There are two illuminated cupholders located in the front. There are two cupholders located in the back for the rear passengers. Illuminated front cupholders rear cupholders 178 understanding the features of your vehicle.

  • Page 181

    Storage glove compartment and storage bin located on the passenger side of the instrument panel are an upper storage bin and a lower glove compartment. To open the lower glove compartment, pull outward on the release handle. 1 — upper storage bin 2 — lower glove compartment glove compartment 3 under...

  • Page 182

    Door storage the interior door panels are equipped with lower storage areas. Front door storage rear door storage 180 understanding the features of your vehicle.

  • Page 183

    Console features the floor console contains both an upper and lower storage compartment. To open the upper storage compartment, push inward on the upper handle to unlatch the upper lid and lift the lid open. To open the lower storage compartment, lift upward on the lower handle to unlatch the lower ...

  • Page 184

    Warning! Do not operate this vehicle with a console compart- ment lid in the open position. Cellular phones, music players, and other handheld electronic devices should be stowed while driving. Use of these devices while driving can cause an accident due to distrac- tion, resulting in death or injur...

  • Page 185

    Cargo cover the cargo area trim panels include two notches for mounting the available tonneau cover that accommo- dates the reclining rear seat. To install the cargo cover, insert either end of the cover into one of the two notches located in the rear trim panels. With one of the cover ends installe...

  • Page 186

    Using the handle, pull the cover toward you and guide the rear cover posts into the guides located on both sides of the rear trim panel. Warning! In a collision a cargo cover loose in the vehicle could cause injury. It could fly around in a sudden stop and strike someone in the vehicle. Do not store...

  • Page 187

    Removable load floor the cargo area load floor is removable and can be washed with mild soap and water. Cargo tie-down loops there are four d-rings installed in the cargo area for securing cargo. Cargo load floor d-rings 3 understanding the features of your vehicle 185.

  • Page 188

    Warning! • cargo tie-down loops are not safe anchors for a child seat tether strap. In a sudden stop or collision a loop could pull loose and allow the child seat to come loose. A child could be badly injured. Use only the anchors provided for child seat tethers. • the weight and position of cargo a...

  • Page 189

    Fold down speakers — if equipped when the liftgate is open, the speakers can swing down off the trim panel to face rearward, for tailgating and other activities. Rear window features rear window wiper/washer the rear wiper/washer is controlled by a rotary switch located on the center portion of the ...

  • Page 190

    Rotate the center portion of the lever upward to the first detent position for rear wiper operation. Note: the rear wiper operates in an intermittent mode only. Rotate the center portion of the lever past the first detent to activate the rear washer. The washer pump and the wiper will continue to op...

  • Page 191

    Caution! (continued) • use care when washing the inside of the rear window. Do not use abrasive window cleaners on the interior surface of the window. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements. Labels can be peeled off after soaking with warm water. • do n...

  • Page 192

    Note: • to help control wind noise when the crossbars are not in use, place the front crossbar in the first detent from the front of the vehicle and the rear crossbar in the second detent from the rear of the vehicle. • if the rear crossbar (or any metallic object) is placed over the satellite radio...

  • Page 193

    Caution! (continued) • long loads which extend over the windshield, such as wood panels or surfboards, or loads with large frontal area should be secured to both the front and rear of the vehicle. • travel at reduced speeds and turn corners care- fully when carrying large or heavy loads on the roof ...

  • Page 195: Contents

    Understanding your instrument panel contents 䡵 instrument panel features . . . . . . . . . . . . . . . 196 䡵 instrument cluster . . . . . . . . . . . . . . . . . . . . 197 䡵 instrument cluster descriptions . . . . . . . . . . . 198 䡵 mini-trip computer — if equipped . . . . . . . . 211 ▫ control but...

  • Page 196

    䡵 media center 230 (req) — am/fm stereo radio and 6–disc cd/dvd changer (mp3/wma aux jack) . . . . . . . . . . . . . . . . . . 224 ▫ operating instructions - radio mode . . . . . . 224 ▫ operation instructions - (disc mode for cd and mp3/wma audio play, dvd-video) . . . 232 ▫ notes on playing mp3/wm...

  • Page 197

    䡵 media center 130 with satellite radio (sales code res+rsc). . . . . . . . . . . . . . . . . . . 252 ▫ operating instructions — radio mode . . . . . 252 ▫ operation instructions — cd mode for cd and mp3 audio play . . . . . . . . . . . . . . . . . 258 ▫ notes on playing mp3 files . . . . . . . . . ...

  • Page 198

    Instrument panel features 1 — air outlet 5 — storage bin 9 — heated seat switch – if equipped 2 — demisters 6 — glove compartment 10 — hazard warning flasher 3 — instrument cluster 7 — climate controls 11 — esc off switch – if equipped 4 — radio 8 — power outlet 12 — heated seat switch – if equipped...

  • Page 199

    Instrument cluster 4 understanding your instrument panel 197.

  • Page 200

    Instrument cluster descriptions 1. Fuel gauge/fuel door reminder when the ignition switch is in the on/run position, the pointer will show the level of fuel remaining in the fuel tank. The fuel pump symbol points to the side of the vehicle where the fuel door is located. 2. Charging system light thi...

  • Page 201

    On briefly as a bulb check. If the light does not come on during starting, have the system checked by an autho- rized dealer. 4. Oil pressure warning light this light indicates low engine oil pressure. The light should turn on momentarily when the engine is started. If the light turns on while drivi...

  • Page 202

    Note: if either indicator flashes at a rapid rate, check for a defective outside light bulb. 9. High beam indicator this indicator shows that the high beam head- lights are on. Push the multifunction lever forward to switch the headlights to high beam, and pull toward yourself (normal position) to r...

  • Page 203

    12. Tachometer the white area of the scale shows the permissible engine revolutions-per-minute (rpm x 1000) for each gear range. Before reaching the red area, ease up on the accelerator to prevent engine damage. 13. Engine temperature warning light this light warns of an overheated engine condi- tio...

  • Page 204

    Booster, the abs pump will run when applying the brake and a brake pedal pulsation may be felt during each stop. The dual brake system provides a reserve braking capac- ity in the event of a failure to a portion of the hydraulic system. A leak in either half of the dual brake system is indicated by ...

  • Page 205

    The light also will turn on when the parking brake is applied with the ignition switch in the on/run posi- tion. Note: this light shows only that the parking brake is applied. It does not show the degree of brake application. 15. Transmission temperature warning light this light indicates that the t...

  • Page 206

    The gauge pointer will likely indicate a higher tempera- ture when driving in hot weather, up mountain grades, or when towing a trailer. It should not be allowed to exceed the upper limits of the normal operating range. Caution! Driving with a hot engine cooling system could damage your vehicle. If ...

  • Page 207

    20. Shift lever indicator the shift lever indicator is self-contained within the instrument cluster. It displays the gear position of the automatic transmission. Note: you must apply the brakes before shifting from park. 21. Odometer/trip odometer display reset button press this button to change the...

  • Page 208

    Reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability. Please note that the tpms is not a substitute for proper tire maintenance, and it is the driver’s responsibility to maintain correct tire pressure, even if under-inflation has not reached the lev...

  • Page 209

    23. Odometer display / trip odometer display this display indicates the total distance the vehicle has been driven. Note: u.S. Federal regulations require that upon trans- fer of vehicle ownership, the seller certify to the pur- chaser the correct mileage that the vehicle has been driven. If your od...

  • Page 210

    “gascap” message will display in the odometer display area. Tighten the fuel filler cap properly and press the trip odometer button to turn off the message. If the problem continues, the message will appear the next time the vehicle is started. Low tire when tire pressure is low, the odometer displa...

  • Page 211

    25. Malfunction indicator light (mil) the malfunction indicator light (mil) is part of an onboard diagnostic system called obd ii that monitors emissions, engine, and automatic trans- mission control systems. The light will illuminate when the key is in the on/run position before engine start. If th...

  • Page 212

    26. Hill descent indicator — if equipped the symbol illuminates (is armed) when the 4wd lock switch is activated and the trans- mission range indicator is in low or reverse position (off-road mode). 27. Front fog light indicator — if equipped this indicator will illuminate when the front fog lights ...

  • Page 213

    • each time the ignition is turned to on/run, the esc system will be on, even if it was turned off previously. • the esc system will make buzzing or clicking sounds when it is active. This is normal; the sounds will stop when esc becomes inactive following the maneuver that caused the esc activation...

  • Page 214

    Control buttons step button press the step button located on the steering wheel to scroll through sub menus (i.E., temperature, trip func- tions: odometer, trip a, trip b). Reset button to reset the display shown, turn the ignition switch to the on position, then press and hold the reset button loca...

  • Page 215

    Electronic vehicle information center (evic) — if equipped the electronic vehicle information center (evic) fea- tures a driver-interactive display that is located in the instrument cluster. The evic consists of the following: • system status • vehicle information warning message displays • personal...

  • Page 216

    The system allows the driver to select information by pressing the following buttons mounted on the steering wheel: menu button press and release the menu button to scroll through the main menus (fuel economy, warn- ings, timer, units, system, personal settings) or to exit sub-menus. Compass button ...

  • Page 217

    Down button press and release the down button to scroll downward through the sub-menus. When the appropriate conditions exist, the evic displays the following messages: • turn signal on (with a continuous warning chime after 1 mile (1.6 km) of distance travelled) • left front turn signal lamp out (w...

  • Page 218

    • remote start aborted — fuel low • remote start aborted — system fault • key in ignition • low tire • low tire pressure display for premium tpm system • service tpm system engine oil change indicator system — if equipped oil change required your vehicle is equipped with an engine oil change indicat...

  • Page 219

    Note: if the indicator message illuminates when you start the vehicle, the oil change indicator system did not reset. If necessary repeat this procedure. Evic functions • compass/temperature/audio • average fuel economy • distance to empty (dte) • elapsed time • tire pressure monitor (tpm) • persona...

  • Page 220

    Distance to empty (dte) shows the estimated distance that can be traveled with the fuel remaining in the tank. This estimated distance is determined by a weighted average of the instantaneous and average fuel economy, according to the current fuel tank level. This is not resettable. Note: significan...

  • Page 221

    Personal settings (customer-programmable features) this allows the driver to set and recall features when the transmission is in park (automatic transmission) or the vehicle is stopped (manual transmission). Press and release the menu or down buttons until “personal settings” is displayed in the evi...

  • Page 222

    Rke unlock driver’s door 1st when driver’s door 1st is selected only the driver’s door will unlock on the first press of the remote keyless entry (rke) transmitter unlock button and require a second press to unlock the remaining locked doors. When re- mote unlock all doors is selected, all of the do...

  • Page 223

    Either front vehicle door will cancel this feature. Press and hold the select button when in this display until “off”, “45 sec.”, “5 min.”, or “10 min.” appears to make your selection. Illuminated approach when this feature is selected the headlights will activate and remain on for up to 90 seconds ...

  • Page 224

    Metallic objects) until the “cal” message displayed in the evic turns off. The compass will now function normally. Note: a good calibration requires a level surface and an environment free from large metallic objects such as buildings, bridges, underground cables, railroad tracks, etc. Manual compas...

  • Page 225

    Note: magnetic materials should be kept away from the top of the right rear quarter window. This is where the compass sensor is located. 1. Turn the ignition switch on. 2. Press and hold the compass button for approxi- mately two seconds. 3. Press the down button until “compass variance” message and...

  • Page 226

    Media center 230 (req) — am/fm stereo radio and 6–disc cd/dvd changer (mp3/wma aux jack) note: the radio sales code is located on the lower right side of the radio faceplate. Operating instructions - radio mode note: the ignition switch must be in the on or acc position to operate the radio. Power s...

  • Page 227

    Seek buttons press and release the seek buttons to search for the next listenable station in am/fm mode. Press the right switch to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection. Holding either button will bypass stations wit...

  • Page 228

    Clock setting procedure 1. Press and hold the time button until the hours blink. 2. Adjust the hours by turning the right side tune/ scroll control knob. 3. After adjusting the hours, press the right side tune/ scroll control knob to set the minutes. The minutes will begin to blink. 4. Adjust the mi...

  • Page 229

    Push the rotary tune/scroll control knob a second time and mid will display. Turn the tune/scroll control knob to the right or left to increase or decrease the mid-range tones. Push the rotary tune/scroll control knob a third time and treble will display. Turn the tune/scroll control knob to the rig...

  • Page 230

    Program type 16-digit character display information inform jazz jazz news news nostalgia nostalga oldies oldies personality persnlty public public rhythm and blues r & b religious music rel musc religious talk rel talk rock rock soft soft soft rock soft rck soft rhythm and blues soft r & b sports sp...

  • Page 231

    • dvd enter - when the disc is in dvd menu mode, selecting dvd enter will allow you to play the current highlighted selection. Use the remote control to scroll up and down the menu (if equipped). • disc play/pause - you can toggle between playing the dvd and pausing the dvd by pushing the select but...

  • Page 232

    • set home clock - pressing the select button allows you to set the clock. Turn the tune/scroll control knob to adjust the hours and then press and turn the tune/scroll control knob to adjust the minutes. Press the tune/scroll control knob again to save changes. • player defaults - selecting this it...

  • Page 233

    Audio drc — if equipped selecting this item allows you to limit maximum audio dynamic range. The default is set to ⬙high,⬙ and under this setting, dialogues will play at 11 db higher than if the setting is ⬙normal.⬙ aspect ratio — if equipped selecting this item allows you to choose between wide scr...

  • Page 234

    You may add a second station to each pushbutton by repeating the above procedure with this exception: press the set button twice and set 2 will show in the display window. Each button can be set for set 1 and set 2 in both am and fm. This allows a total of 12 am, 12 fm, and 12 satellite (if equipped...

  • Page 235

    Note: the ignition switch must be in the on or acc position to operate the radio. Load button — loading compact disc(s) press the load button and the pushbutton with the corresponding number (1-6) where the cd is being loaded. The radio will display please wait and prompt when to insert disc. After ...

  • Page 236

    Scan button (cd mode) press the scan button to scan through each track on the cd currently playing. Time button (cd mode) press this button to change the display from a large cd playing time display to a small cd playing time display. Rw/ff (cd mode) press and hold ff (fast forward) and the cd playe...

  • Page 237

    The radio uses the following limits for file systems: • maximum number of directory levels: 8 • maximum number of files: 255 • maximum number of folders: 100 • maximum number of characters in file/folder names: • level 1: 12 (including a separator ⬙.⬙ and a three- character extension) • level 2: 31 ...

  • Page 238

    Mpeg specification sampling fre- quency (khz) bit rate (kbps) mpeg-1 audio layer 3 48, 44.1, 32 320, 256, 224, 192, 160, 128, 112, 96, 80, 64, 56, 48 mpeg-2 audio layer 3 24, 22.05, 16 160, 128, 144, 112, 96, 80, 64, 56, 48 wma specifica- tion sampling fre- quency (khz) bit rate (kbps) wma 44.1 and ...

  • Page 239

    List button (disc mode for mp3/wma play) pressing the list button will bring up a list of all folders on the disc. Scrolling up or down the list is done by turning the tune/scroll control knob. Selecting a folder by pressing the tune/scroll control knob will begin playing the files contained in that...

  • Page 240

    Scan button (auxiliary mode) no function. Eject button (auxiliary mode) no function. Time button (auxiliary mode) press the time button to change the display from elapsed playing time to time of day. The time of day will display for five seconds. Rw/ff (auxiliary mode) no function. Set button (auxil...

  • Page 241

    Macrovision this product incorporates copyright protection technol- ogy that is protected by u.S. Patents and other intellec- tual property rights. Use of this copyright protection technology must be authorized by macrovision, and is intended for home and other limited viewing uses only, unless othe...

  • Page 242

    2. Your vehicle identification number. To access the esn/sid, refer to the following steps: esn/sid access with the ignition switch in the on/run or acc posi- tion and the radio on, press the setup button and scroll using the tune/scroll control knob until sirius id is selected. Press the tune/scrol...

  • Page 243

    Operating instructions - uconnect™ multimedia (satellite) mode note: the ignition switch must be in the on/run or acc position to operate the radio. Seek buttons press and release the seek buttons to search for the next channel in satellite mode. Press the right switch to seek up and the left switch...

  • Page 244

    Or turning the tune/scroll control knob within five seconds will allow the program format type to be selected. Toggle the music type button again to select the music type. By pressing the seek button when the music type function is active, the radio will be tuned to the next channel with the same se...

  • Page 245

    Buttons 1 - 6 these buttons tune the radio to the channels that you commit to pushbutton memory (12 satellite stations). Media center 730n/430/430n (rhr/rer/rbz/ rhb) cd/dvd/hdd/nav — if equipped note: the sales code is located on the lower right side of the unit’s faceplate. Refer to your uconnect™...

  • Page 246

    Operating instructions — radio mode note: the ignition switch must be in the on or acc position to operate the radio. Power switch/volume control (rotary) push the on/volume control knob to turn on the radio. Push the on/volume control knob a second time to turn off the radio. Electronic volume cont...

  • Page 247

    4. Adjust the minutes using the right side tune/ scroll control knob. Press the tune/scroll control knob to save time change. 5. To exit, press any button/knob, or wait five seconds. Rw/ff pressing the rw (rewind) or ff (fast forward) buttons causes the tuner to search for the next frequency in the ...

  • Page 248

    Push the rotary tune/scroll control knob again to exit setting tone, balance, and fade. Am/fm button press the buttons to select either am or fm mode. Set/rnd button — to set the pushbutton memory when you are receiving a station that you wish to commit to pushbutton memory, press the set/rnd button...

  • Page 249

    Operation instructions — cd mode for cd and mp3 audio play note: • the ignition switch must be in the on or acc position to operate the radio. • this radio is capable of playing compact discs (cd), recordable compact discs (cd-r), rewritable compact discs (cd-rw), compact discs with mp3 tracks and m...

  • Page 250

    Eject button - ejecting a cd press the eject button to eject the cd. If you have ejected a disc and have not removed it within 10 seconds, it will be reloaded. If the cd is not removed, the radio will reinsert the cd but will not play it. A disc can be ejected with the radio and ignition off. Note: ...

  • Page 251

    Set/rnd button (random play button) press this button while the cd is playing to activate random play. This feature plays the selections on the compact disc in random order to provide an interesting change of pace. Press the right seek button to move to the next ran- domly selected track. Press the ...

  • Page 252

    • maximum number of characters in file/folder names: • level 1: 12 (including a separator ⬙.⬙ and a three- character extension) • level 2: 31 (including a separator ⬙.⬙ and a three- character extension) multisession disc formats are supported by the radio. Multisession discs may contain combinations...

  • Page 253

    Playlist files are not supported. Mp3 pro files are not supported. Playback of mp3 files when a medium containing mp3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the mp3 files. Loading time...

  • Page 254

    Time button (auxiliary mode) press this button to change the display to time of day. The time of day will display for five seconds (when ignition is off). Media center 130 with satellite radio (sales code res+rsc) note: the radio sales code is located on the lower right side of the radio faceplate. ...

  • Page 255

    Power switch/volume control (rotary) push the on/volume control knob to turn on the radio. Push the on/volume control knob a second time to turn off the radio. Electronic volume control the electronic volume control turns continuously (360 degrees) in either direction without stopping. Turning the o...

  • Page 256

    If your vehicle is not equipped with or this feature is not available on your vehicle, a “not equipped with uconnect phone” message will display on the radio screen. Time button press the time button to alternate display of the time and radio frequency. Clock setting procedure 1. Press and hold the ...

  • Page 257

    Tune control turn the rotary tune/scroll control knob clockwise to increase or counterclockwise to decrease the frequency. Setting the tone, balance, and fade push the rotary tune/scroll control knob and bass will display. Turn the tune/scroll control knob to the right or left to increase or decreas...

  • Page 258

    Toggle the music type button to select the following format types: program type 16-digit character display no program type or undefined none adult hits adlt hit classical classicl classic rock cls rock college college country country foreign language language information inform jazz jazz news news n...

  • Page 259

    If a preset button is activated while in the music type (program type) mode, the music type mode will be exited and the radio will tune to the preset station. Setup button pressing the setup button allows you to select between the following items: • set clock — pressing the select button will allow ...

  • Page 260

    Every time a preset button is used, a corresponding button number will display. Buttons 1 - 6 these buttons tune the radio to the stations that you commit to pushbutton memory (12 am and 12 fm stations). Disc/aux button pressing the disc/aux button will allow you to switch from am/fm modes to disc/a...

  • Page 261

    Caution! • this cd player will accept 4–3/4 in (12 cm) discs only. The use of other sized discs may damage the cd player mechanism. • do not use adhesive labels. These labels can peel away and jam the player mechanism. • the res media center is a single cd player. Do not attempt to insert a second c...

  • Page 262

    Rw/ff press and hold ff (fast forward) and the cd player will begin to fast forward until ff is released or rw or another cd button is pressed. The rw (reverse) button works in a similar manner. Am/fm button press the button to select either am or fm mode. Set/rnd button (random play button) press t...

  • Page 263

    The radio uses the following limits for file systems: • maximum number of folder levels: 8 • maximum number of files: 255 • maximum number of folders. (the radio display of file names and folder names is limited. For large numbers of files and/or folders, the radio may be unable to display the file ...

  • Page 264

    Rates (vbr) are also supported. The majority of mp3 files use a 44.1 khz sampling rate and a 192, 160, 128, 96 or vbr bit rates. Mpeg specification sampling fre- quency (khz) bit rate (kbps) mpeg-1 audio layer 3 48, 44.1, 32 320, 256, 224, 192, 160, 128, 112, 96, 80, 64, 56, 48, 40, 32 mpeg-2 audio ...

  • Page 265

    List button (cd mode for mp3 play) pressing the list button will bring up a list of all folders on the disc. Scrolling up or down the list is done by turning the tune/scroll control knob. Selecting a folder by pressing the tune/scroll control knob will begin playing the files contained in that folde...

  • Page 266

    Time button (auxiliary mode) press this button to change the display to time of day. The time of day will display for five seconds (when the ignition is off). Uconnect™ multimedia (satellite radio) — if equipped satellite radio uses direct satellite-to-receiver broadcast- ing technology to provide c...

  • Page 267

    Using the tune/scroll control knob until sirius id is selected. Press the tune/scroll control knob and the sirius id number will display. The sirius id number display will time out in two minutes. Press any button on the radio to exit this screen. Selecting uconnect™ multimedia (satellite) mode pres...

  • Page 268

    Seek buttons press and release the seek buttons to search for the next channel in satellite mode. Press the right switch to seek up and the left switch to seek down. The radio will remain tuned to the new channel until you make another selection. Holding either button will bypass channels without st...

  • Page 269

    Toggle the music type button again to select the music type. By pressing the seek button when the music type function is active, the radio will be tuned to the next channel with the same selected music type name. If a preset button is activated while in the music type (program type) mode, the music ...

  • Page 270

    Every time a preset button is used, a corresponding button number will display. Buttons 1 - 6 these buttons tune the radio to the channels that you commit to pushbutton memory (12 satellite stations). Operating instructions - uconnect™ phone (if equipped) refer to “uconnect™ phone” in “understanding...

  • Page 271

    Connecting the ipod 姞 or external usb device use the connection cable to connect an ipod 威 or external usb device to the vehicle’s usb/aux connector port which is located in the center console or glove compart- ment. Once the audio device is connected and synchronized to the vehicle’s ipod 威/usb/mp3...

  • Page 272

    • the audio device can be controlled using the radio buttons to play, browse, and list the ipod 威 contents. • the audio device battery charges when plugged into the usb/aux connector (if supported by the specific audio device) controlling the ipod 姞 or external usb device using radio buttons to get ...

  • Page 273

    • a single press backward rw or forward ff >> will jump backward or forward respectively, for five seconds. • use the seek and seek >> buttons to jump to the previous or next track. Pressing the seek >> button during play mode will jump to the next track in the list, or press the vr button and say ⬙...

  • Page 274

    List or browse mode during play mode, pressing any of the buttons described below, will bring up list mode. List mode enables scrolling through the list of menus and tracks on the audio device. • tune control knob: the tune control knob functions in a similar manner as the scroll wheel on the audio ...

  • Page 275

    • pressing a preset button will display the current list on the top line and the first item in that list on the second line. • to exit list mode without selecting a track, press the same preset button again to go back to play mode . • list button: the list button will display the top level menu of t...

  • Page 276

    Bluetooth streaming audio (btsa) music can be streamed from your cellular phone to the uconnect™ phone system. Controlling btsa using radio buttons to get into the btsa mode, press either “aux” button on the radio or press the vr button and say “bluetooth streaming audio”. Play mode when switched to...

  • Page 277

    Steering wheel audio controls the remote sound system controls are located on the rear surface of the steering wheel. Reach behind the wheel to access the switches. The right-hand control is a rocker-type switch with a pushbutton in the center and controls the volume and mode of the sound system. Pr...

  • Page 278

    The button located in the center of the left-hand control will tune to the next preset station that you have pro- grammed in the radio preset pushbutton. Cd player pressing the top of the switch once will go to the next track on the cd. Pressing the bottom of the switch once will go to the beginning...

  • Page 279

    Note: if you experience difficulty in playing a particu- lar disc, it may be damaged (i.E., scratched, reflective coating removed, a hair, moisture or dew on the disc) oversized, or have protection encoding. Try a known good disc before considering disc player service. Radio operation and mobile pho...

  • Page 280

    Blower control rotate this control to regulate the amount of air forced through the ven- tilation system in any mode. The blower speed increases as you move the control to the right from the “o” (off) position. There are seven blower speeds. Note: for vehicles equipped with remote start, the climate...

  • Page 281

    Mode control (air direction) rotate this control to choose from sev- eral patterns of air distribution. You can select either a primary mode as identified by the symbols on the con- trol, or a blend of two of these modes. The closer the setting is to a particular symbol, the more air distribution yo...

  • Page 282

    Defrost air is directed through the windshield and side window demist outlets. Use this mode with maxi- mum blower and temperature settings for best wind- shield and side window defrosting. Note: • the air conditioning compressor operates in mix, defrost, or a blend of these modes, even if the air c...

  • Page 283

    • the a/c can be deselected manually without disturb- ing the mode control selection. • when the ignition switch is turned to the lock position, the recirculation feature will be cancelled. Air conditioning control press this button to engage the air conditioning. A light will illuminate when the ai...

  • Page 284

    Automatic temperature control (atc) — if equipped the automatic temperature control system automati- cally maintains the climate in the cabin of the vehicle at the comfort levels desired by the driver and passenger. Automatic operation operation of the system is quite simple. 1. Turn the mode contro...

  • Page 285

    You will experience the greatest efficiency by simply allowing the system to function automatically. Selecting the “o” (off) position on the blower control stops the system completely and closes the outside air intake. The recommended setting for maximum comfort for the average person is 72°f (22°c)...

  • Page 286

    Blower control for full automatic operation or for automatic blower operation, turn the knob to the auto position. In manual mode there are seven blower speeds that can be individual selected. In off position the blower will shut off. Manual operation this system offers a full complement of manual o...

  • Page 287

    Understanding your instrument panel 285.

  • Page 288

    The operator can override the auto mode setting to change airflow distribution by rotating the mode control knob (on the right) to one of the following positions. • panel air is directed through the outlets in the instrument panel. These outlets can be adjusted to direct airflow. Note: the center in...

  • Page 289

    • air conditioner control press this button to turn on the air conditioning during manual operation only. When the air conditioning is turned on, cool dehumidified air will flow through the outlets selected with the mode control dial. Press this but- ton a second time to turn off the air conditionin...

  • Page 290

    • most of the time, when in automatic operation, you can temporarily put the system into recirculation mode by pressing the recirculation button. However, under certain conditions, while in automatic mode, the system is blowing air out the defrost vents. When these conditions are present, and the re...

  • Page 291

    Window fogging interior fogging on the windshield can be quickly re- moved by turning the mode selector to defrost. The defrost/floor mode can be used to maintain a clear windshield and provide sufficient heating. If side win- dow fogging becomes a problem, increase blower speed. Vehicle windows ten...

  • Page 292

    Control setting suggestions for various weather conditions 290 understanding your instrument panel.

  • Page 293: Starting And Operating

    Starting and operating contents 䡵 starting procedures . . . . . . . . . . . . . . . . . . . . 295 ▫ manual transmission – if equipped . . . . . . . 295 ▫ automatic transmission – if equipped . . . . . 296 ▫ normal starting . . . . . . . . . . . . . . . . . . . . . 296 ▫ extreme cold weather (below –...

  • Page 294

    䡵 autostick威 . . . . . . . . . . . . . . . . . . . . . . . . . . 308 ▫ operation . . . . . . . . . . . . . . . . . . . . . . . . . 308 ▫ general information . . . . . . . . . . . . . . . . . . 309 䡵 four-wheel drive operation — if equipped . . 309 䡵 on-road driving tips . . . . . . . . . . . . . . ....

  • Page 295

    ▫ esc activation/malfunction indicator light and esc off indicator light . . . . . . . . . . . . 335 䡵 tire safety information . . . . . . . . . . . . . . . . . 337 ▫ tire markings . . . . . . . . . . . . . . . . . . . . . . . 337 ▫ tire identification number (tin) . . . . . . . . . 340 ▫ tire termi...

  • Page 296

    ▫ general information . . . . . . . . . . . . . . . . . . 366 䡵 fuel requirements . . . . . . . . . . . . . . . . . . . . . 367 ▫ 2.0l and 2.4l engine . . . . . . . . . . . . . . . . . 367 ▫ reformulated gasoline . . . . . . . . . . . . . . . . 367 ▫ gasoline/oxygenate blends . . . . . . . . . . . ....

  • Page 297

    Starting procedures before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. Warning! • before exiting a vehicle, always apply the parking brake, shift the transmission into park, and re- move the key fob from the ignition. When leaving the ...

  • Page 298

    Automatic transmission – if equipped the shift lever must be in the park or neutral position before you can start the engine. Apply the brakes before shifting to any driving gear. Note: you must press the brake pedal before shifting out of park. Tip start do not press the accelerator. Turn the ignit...

  • Page 299

    Extreme cold weather (below –20°f or ⫺ 29°c) to ensure reliable starting at these temperatures, use of an externally powered electric engine block heater (avail- able from your authorized dealer) is recommended. If engine fails to start if the engine fails to start after you have followed the “norma...

  • Page 300

    Engine block heater — if equipped the engine block heater warms the engine, and permits quicker starts in cold weather. Connect the cord to a standard 110-115 volt ac electrical outlet with a grounded, three-wire extension cord. The engine block heater must be plugged in at least one hour to have an...

  • Page 301

    Use each gear in numerical order, do not skip a gear. Be sure the transmission is in first gear, (not third), when starting from a standing position. Damage to the clutch can result from starting in third gear. For most city driving, you will find it easier to use only the lower gears. For steady hi...

  • Page 302

    Manual transmission recommended shift speeds units in mph (km/h) engine size accel- eration rate 1 to 2 2 to 3 3 to 4 4 to 5 all engines accel 14 (23) 23 (37) 29 (47) 45 (72) cruise 12 (19) 18 (29) 25 (40) 32 (52) downshifting proper downshifting will improve fuel economy and prolong engine life. Ca...

  • Page 303

    Caution! (continued) • do not shift between park, reverse, neu- tral, or drive when the engine is above idle speed. • before shifting into any gear, make sure your foot is firmly pressing the brake pedal. Note: you must press and hold the brake pedal while shifting out of park. Warning! • unintended...

  • Page 304

    Key ignition park interlock this vehicle is equipped with a key ignition park inter- lock which requires the shift lever to be placed in park before the ignition switch can be turned to the lock/ off position. The key fob can only be removed from the ignition when the ignition is in the lock/off pos...

  • Page 305

    Transmission gear ratios, and will display the current gear in the instrument cluster as 6, 5, 4, 3, 2, 1. Gear ranges do not race the engine when shifting from park or neutral into another gear range. Park this range supplements the parking brake by locking the transmission. The engine can be start...

  • Page 306

    Warning! • never use the park position as a substitute for the parking brake. Always apply the parking brake fully when parked to guard against vehicle movement and possible injury or damage. • your vehicle could move and injure you and others if it is not completely in park. Check by trying to move...

  • Page 307

    Warning! (continued) • unintended movement of a vehicle could injure those in or near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, always apply the parking brake, shift the transmission into park, and remove the ignition ke...

  • Page 308

    Caution! (continued) • do not race the engine when shifting from park or neutral into another gear range, as this can damage the drivetrain. The following indicators should be used to ensure that you have engaged the shift lever into the park position: • when shifting into park, move the shift lever...

  • Page 309

    Caution! Towing the vehicle, coasting, or driving for any other reason with the transmission in neutral can result in severe transmission damage. Refer to “recre- ational towing” in “starting and operating” and “towing a disabled vehicle” in what to do in emergencies” for further information. Drive ...

  • Page 310

    Autostick 姞 autostick 威 is a driver-interactive transmission that offers six manual ratio changes to provide you with more control. Autostick 威 allows you to maximize engine brak- ing, eliminate undesirable upshifts and downshifts, and improve overall vehicle performance. This system can also provid...

  • Page 311

    • when heavy anti-lock brake system (abs) applica- tion is detected general information • if a ratio other than first is selected and the vehicle is brought to a stop, the transmission control logic will automatically select the first gear ratio. • if a low range is selected and the engine accelerat...

  • Page 312

    Traction surfaces, activate the “4wd lock” switch by pulling up once and releasing. This locks the center coupling allowing more torque to be sent to the rear wheels. The “4wd indicator light” will come on in the cluster. This can be done on the fly, at any vehicle speed. To deactivate, simply pull ...

  • Page 313

    You will need to use your own good judgment on what is safe and what is not. When on a trail, you should always be looking ahead for surface obstacles and changes in terrain. The key is to plan your future driving route while remembering what you are currently driving over. Caution! Never park your ...

  • Page 314

    Driving in snow, mud and sand there is a drastic reduction in traction when driving in snow, mud or sand. The vehicle will be less responsive to steering, acceleration and braking inputs. Therefore, you should accelerate slowly, leave greater stopping distances and avoid abrupt vehicle maneuvers. Yo...

  • Page 315

    Sand soft sand is very difficult to travel through with full tire pressure. When crossing soft sandy spots in a trail maintain your vehicle’s momentum and do not stop. The key to driving in soft sand is using the appropriate tire pressure, accelerating slowly, avoiding abrupt maneu- vers and maintai...

  • Page 316

    Is on the hill side trail. Is the trail straight up and down? What is on top and the other side? Are there ruts, rocks, branches or other obstacles on the path? Can you safely recover the vehicle if something goes wrong? If every- thing looks good and you feel confident, then you should use low (l o...

  • Page 317

    Controlled descent? Are there obstacles? Is it a straight descent? Is there plenty of distance at the base of the hill to regain control if the vehicle descends to fast? If you feel confident in your ability to proceed then make sure you are in low (l off-road) with the 4wd lock engaged and proceed ...

  • Page 318

    Warning! If the engine stalls or you lose headway or cannot make it to the top of a steep hill or grade, never attempt to turn around. To do so may result in tipping and rolling the vehicle, which may result in severe injury. Always back carefully straight down a hill in reverse gear. Never back dow...

  • Page 319

    Caution! Water ingestion into the transaxle, transfer case, engine or vehicle interior can occur if you drive too fast or through too deep of water. Water can cause permanent damage to engine, driveline or other vehicle components and your brakes will be less effective once wet and/or muddy. Before ...

  • Page 320

    After driving off-road off-road operation puts more stress on your vehicle than does most on-road driving. After going off-road, it is always a good idea to check for damage. That way you can get any problems taken care of right away and have your vehicle ready when you need it. • completely inspect...

  • Page 321

    • if you experience unusual vibration after driving in mud, slush or similar conditions, check the wheels for impacted material. Impacted material can cause a wheel imbalance and freeing the wheels of it will correct the situation. Power steering the standard power steering system will give you good...

  • Page 322

    Caution! Prolonged operation of the steering system at the end of the steering wheel travel will increase the steering fluid temperature and it should be avoided when possible. Damage to the power steering pump may occur. Power steering fluid check checking the power steering fluid level at a define...

  • Page 323

    If necessary, add fluid to restore to the proper indicated level. With a clean cloth, wipe any spilled fluid from all surfaces. Refer to “fluids, lubricants, and genuine parts” in “maintaining your vehicle” for further information. Parking brake before leaving the vehicle, make sure that the parking...

  • Page 324

    Note: • when the parking brake is applied and the automatic transmission is placed in gear, the “brake warning light” will flash. If vehicle speed is detected, a chime will sound to alert the driver. Fully release the parking brake before attempting to move the vehicle. • this light only shows that ...

  • Page 325

    Warning! (continued) • always fully apply the parking brake when leav- ing your vehicle or it may roll and cause damage or injury. Also, be certain to leave an automatic transmission in park, a manual transmission in reverse or first gear. Failure to do so may cause the vehicle to roll and cause dam...

  • Page 326

    Malfunction is caused by an internal leak, as the brake fluid in the master cylinder drops, the “brake warning light” will light. Warning! Driving a vehicle with the “brake warning light” on is dangerous. A significant decrease in braking per- formance or vehicle stability during braking may occur. ...

  • Page 327

    Warning! (continued) • the capabilities of an abs-equipped vehicle must never be exploited in a reckless or dangerous manner which could jeopardize the user’s safety or the safety of others. The “abs warning light” monitors the abs system. The light will come on when the ignition switch is turned to...

  • Page 328

    Abs is activated during braking under certain road or stopping conditions. Abs-inducing conditions can in- clude ice, snow, gravel, bumps, railroad tracks, loose debris, or panic stops. You may also experience the following when the brake system goes into anti-lock mode: • the abs motor running (it ...

  • Page 329

    Assist (hsa), and electronic stability control (esc). All systems work together to enhance vehicle stability and control in various driving conditions and are commonly referred to as esc. Anti-lock brake system (abs) this system aids the driver in maintaining vehicle control under adverse braking co...

  • Page 330

    Warning! (continued) • the capabilities of a bas-equipped vehicle must never be exploited in a reckless or dangerous manner which could jeopardize the user’s safety or the safety of others. Traction control system (tcs) this system monitors the amount of wheel spin of each of the driven wheels. If w...

  • Page 331

    Note: anytime the esc system is in the “full off” mode, erm is disabled. Refer to “electronic stability control (esc)” in this section for a complete explanation of the available esc modes. Warning! Many factors, such as vehicle loading, road condi- tions and driving conditions, influence the chance...

  • Page 332

    Off” button for five seconds. Refer to “electronic stability control (esc)” in this section of the manual. Hdc operation can be overridden with brake application to slow the vehicle down below the hdc control speed. Conversely, if more speed is desired during hdc control, the accelerator pedal will ...

  • Page 333

    Hsa activation criteria the following criteria must be met in order for hsa to activate: • vehicle must be stopped. • vehicle must be on a 7% grade or greater hill. • gear selection matches vehicle uphill direction (i.E., vehicle facing uphill is in forward gear; vehicle back- ing uphill is in rever...

  • Page 334

    5. Release the clutch pedal. 6. Rotate the steering wheel one-half turn to the left. 7. Press the “esc off” switch (located in the lower switch bank below the climate controls) four times within 20 seconds. The “esc activation/malfunction indicator light” should turn on and turn off two times. 8. Ro...

  • Page 335

    Warning! • electronic stability control (esc) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions. • esc cannot prevent collisions, including those resulting from excessive speed in turns, driving on very slip...

  • Page 336

    In deep snow, sand or gravel conditions and more wheel spin than esc would normally allow is required to gain traction. To turn esc on again, momentarily press the “esc off” switch. This will restore the normal “esc on” mode of operation. Note: to improve the vehicle’s traction when driving with sno...

  • Page 337

    “esc off” message will appear in the odometer. Press and release the trip odometer button located on the instrument cluster to clear this message. In this mode, esc is turned off until the vehicle reaches a speed of 35 mph (56 km/h). At 35 mph (56 km/h) the system returns to “partial off” mode, as d...

  • Page 338

    Light” comes on continuously with the engine running, a malfunction has been detected in the esc system. If this light remains on after several ignition cycles, and the vehicle has been driven several miles (kilometers) at speeds greater than 30 mph (48 km/h), see your autho- rized dealer as soon as...

  • Page 339

    Tire safety information tire markings note: • p (passenger) - metric tire sizing is based on u.S. Design standards. P-metric tires have the letter “p” molded into the sidewall preceding the size designa- tion. Example: p215/65r15 95h. • european-metric tire sizing is based on european design standar...

  • Page 340

    Compact spare tires have the letter “t” or “s” molded into the sidewall preceding the size designation. Ex- ample: t145/80d18 103m. • high flotation tire sizing is based on u.S. Design standards and it begins with the tire diameter molded into the sidewall. Example: 31x10.5 r15 lt. Tire sizing chart...

  • Page 341

    Example: service description: 95 = load index — a numerical code associated with the maximum load a tire can carry h = speed symbol — a symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions — the maximum speed corres...

  • Page 342

    Tire identification number (tin) the tin may be found on one or both sides of the tire, however, the date code may only be on one side. Tires with white sidewalls will have the full tin, including the date code, located on the white sidewall side of the tire. Look for the tin on the outboard side of...

  • Page 343

    Tire terminology and definitions term definition b-pillar the vehicle b-pillar is the structural member of the body located behind the front door. Cold tire inflation pressure cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least 3 hours, or ...

  • Page 344

    Tire loading and tire pressure tire and loading information placard location note: the proper cold tire inflation pressure is listed on the driver’s side b-pillar or the rear edge of the driver’s side door. Tire and loading information placard tire placard location tire and loading information placa...

  • Page 345

    This placard tells you important information about the: 1) number of people that can be carried in the vehicle 2) total weight your vehicle can carry 3) tire size designed for your vehicle 4) cold tire inflation pressures for the front, rear, and spare tires. Loading the vehicle maximum load on the ...

  • Page 346

    3. Subtract the combined weight of the driver and pas- sengers from xxx lbs or xxx kg. 4. The resulting figure equals the available amount of cargo and luggage load capacity. For example, if “xxx” amount equals 1,400 lbs (635 kg) and there will be five 150 lb (68 kg) passengers in your vehicle, the ...

  • Page 347

    Starting and operating 345.

  • Page 348

    Warning! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. Tires — general information tire pressure proper tire inflation pressur...

  • Page 349

    Warning! (continued) • unequal tire pressures from one side of the ve- hicle to the other can cause the vehicle to drift to the right or left. • always drive with each tire inflated to the recom- mended cold tire inflation pressure. Economy improper inflation pressures can cause uneven wear patterns...

  • Page 350

    Caution! After inspecting or adjusting the tire pressure, al- ways reinstall the valve stem cap. This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Inflation pressures specified on the placard are always “cold tire inflation pressure.” cold tire infl...

  • Page 351

    Tire pressures for high speed operation the manufacturer advocates driving at safe speeds within posted speed limits. Where speed limits or condi- tions are such that the vehicle can be driven at high speeds, maintaining correct tire inflation pressure is very important. Increased tire pressure and ...

  • Page 352

    Vehicle. If your vehicle has this option refer to an authorized tire dealer for the recommended tire rotation pattern. If your vehicle is not equipped with an original equip- ment tire and wheel as a spare, a non-matching tempo- rary emergency use spare may be equipped with your vehicle. Temporary u...

  • Page 353

    Warning! Compact spares are for temporary emergency use only. With these spares, do not drive more than 50 mph (80 km/h). Temporary use spares have limited tread life. When the tread is worn to the tread wear indicators, the temporary use spare tire needs to be replaced. Be sure to follow the warnin...

  • Page 354

    Warning! Limited-use spares are for emergency use only. In- stallation of this limited-use spare tire affects vehicle handling. With this tire, do not drive more than the speed listed on the limit-use spare wheel. Keep inflated to the cold tire inflation pressure listed on your tire and loading info...

  • Page 355

    These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth becomes 1/16 in (2 mm). When the tread is worn to the tread wear indicators, the tire should be replaced. Life of tire the service life of a tire is dependent upon varying factors includi...

  • Page 356

    Replacement tires the tires on your new vehicle provide a balance of many characteristics. They should be inspected regularly for wear and correct cold tire inflation pressure. The manu- facturer strongly recommends that you use tires equiva- lent to the originals in size, quality and performance wh...

  • Page 357

    Warning! (continued) • never use a tire with a smaller load index or capacity other than what was originally equipped on your vehicle. Using a tire with a smaller load index could result in tire overloading and failure. You could lose control and have a collision. • failure to equip your vehicle wit...

  • Page 358

    Snow tires generally have lower speed ratings than what was originally equipped with your vehicle and should not be operated at sustained speeds over 75 mph (120 km/h). For speeds above 75 mph (120 km/h) refer to original equipment or an authorized tire dealer for recommended safe operating speeds, ...

  • Page 359

    Tire pressure monitoring system (tpms) the tire pressure monitor system (tpms) will warn the driver of a low tire pressure based on the vehicle recom- mended cold placard pressure. The tire pressure will vary with temperature by about 1 psi (6.9 kpa) for every 12°f (6.5°c). This means that when the ...

  • Page 360

    The tpms will continue to warn the driver of low tire pressure as long as the condition exists, and will not turn off until the tire pressure is at or above the recommended cold placard pressure. Once the low tire pressure warn- ing (tire pressure monitoring telltale light) illuminates, you must inc...

  • Page 361

    Caution! • the tpms has been optimized for the original equipment tires and wheels. Tpms pressures and warnings have been established for the tire size equipped on your vehicle. Undesirable system operation or sensor damage may result when us- ing replacement equipment that is not of the same size, ...

  • Page 362

    • seasonal temperature changes will affect tire pressure, and the tpms will monitor the actual tire pressure in the tire. Base system this is the tpms warning indicator located in the instrument cluster. The tpms uses wireless technology with wheel rim mounted electronic sensors to monitor tire pres...

  • Page 363

    Check tpms warnings the tire pressure monitoring telltale light will flash on and off for 75 seconds and remain on solid when a system fault is detected. The system fault will also sound a chime. If the ignition key is cycled, this sequence will repeat providing the system fault still exists. The ti...

  • Page 364

    4. For each subsequent ignition key cycle, a chime will sound and the tire pressure monitoring telltale light will flash on and off for 75 seconds and then remain on solid. 5. Once you repair or replace the original road tire and reinstall it on the vehicle in place of the compact spare tire, the tp...

  • Page 365

    • various tire pressure monitoring system messages, which display in the electronic vehicle information center (evic) • tire pressure monitoring telltale light tire pressure monitoring low pressure warnings the tire pressure monitoring telltale light will illumi- nate in the instrument cluster and a...

  • Page 366

    The graphic display of the pressure value(s) will stop flashing, and the tire pressure monitoring light will extinguish once the updated tire pressure(s) have been received. The vehicle may need to be driven for up to 20 minutes above 15 mph (24 km/h) to receive this information. Service tpms messag...

  • Page 367

    Will be displayed instead of dashes. A system fault can occur with any of the following scenarios: 1. Jamming due to electronic devices or driving next to facilities emitting the same radio frequencies as the tpm sensors. 2. Installing some form of aftermarket window tinting that affects radio wave ...

  • Page 368

    3. However, after driving the vehicle for up to 20 min- utes above 15 mph (24 km/h), the tire pressure moni- toring telltale light will flash on and off for 75 seconds and then remain on solid. In addition, the evic will display a “service tpm system” message for a mini- mum of five seconds and then...

  • Page 369

    Fuel requirements 2.0l and 2.4l engine this engine is designed to meet all emis- sions regulations and provide excellent fuel economy and performance when us- ing high-quality unleaded “regular” gaso- line having an octane rating of 87. The use of premium gasoline is not recommended, as it will not ...

  • Page 370

    Gasoline/oxygenate blends some fuel suppliers blend unleaded gasoline with oxy- genates such as ethanol. Fuels blended with oxygenates may be used in your vehicle. Caution! Do not use gasoline containing methanol or gaso- line containing more than 10% ethanol. Use of these blends may result in start...

  • Page 371

    • drain the fuel tank (see your authorized dealer) more extensive repairs will be required for prolonged exposure to e-85 fuel. Mmt in gasoline mmt is a manganese-containing metallic additive that is blended into some gasoline to increase octane. Gasoline blended with mmt provides no performance adv...

  • Page 372

    Caution! (continued) • an out-of-tune engine or certain fuel or ignition malfunctions can cause the catalytic converter to overheat. If you notice a pungent burning odor or some light smoke, your engine may be out of tune or malfunctioning and may require immediate service. Contact your authorized d...

  • Page 373

    Warning! (continued) • guard against carbon monoxide with proper maintenance. Have the exhaust system inspected every time the vehicle is raised. Have any abnor- mal conditions repaired promptly. Until repaired, drive with all side windows fully open. • keep the liftgate closed when driving your veh...

  • Page 374

    Caution! • damage to the fuel system or emission control system could result from using an improper fuel tank filler cap (gas cap). A poorly fitting cap could let impurities into the fuel system. • a poorly fitting gas cap may cause the “malfunc- tion indicator light (mil)” to turn on. • to avoid fu...

  • Page 375

    Loose fuel filler cap message if the vehicle diagnostic system determines that the fuel filler cap is loose or improperly installed, a “gascap” message will be displayed in the odometer/trip odom- eter in the instrument cluster. Refer to “instrument cluster description” in “understanding your instru...

  • Page 376

    Gross vehicle weight rating (gvwr) the gvwr is the total allowable weight of your vehicle. This includes driver, passengers, and cargo. The total load must be limited so that you do not exceed the gvwr. Tire size the tire size on the vehicle certification label represents the actual tire size on you...

  • Page 377

    Overloading can cause potential safety hazards and shorten useful service life. Heavier suspension compo- nents do not necessarily increase the vehicle’s gvwr. Loading to load your vehicle properly, first figure out its empty weight. Store heavier items down low and be sure you distribute their weig...

  • Page 378

    Exceed the gvwr. Refer to “vehicle loading/vehicle certification label” in “starting and operating” for further information. Gross trailer weight (gtw) the gtw is the weight of the trailer plus the weight of all cargo, consumables and equipment (permanent or tem- porary) loaded in or on the trailer ...

  • Page 379

    Frontal area the frontal area is the maximum height multiplied by the maximum width of the front of a trailer. Trailer sway control the trailer sway control is a telescoping link that can be installed between the hitch receiver and the trailer tongue that typically provides adjustable friction assoc...

  • Page 380

    Trailer hitch classification your vehicle may be factory equipped for safe towing of trailers weighing over 2,000 lbs (907 kg) with the optional trailer tow prep package. See your authorized dealer for package content. The following chart provides the industry standard for the maximum trailer weight...

  • Page 381

    Trailer towing weights (maximum trailer weight ratings) the following chart provides the maximum trailer weight ratings towable for your given drivetrain. Engine/transmission frontal area max. Gtw (gross trailer wt.) max. Tongue wt. (see note) 2.0l auto/man 22 sq ft (2.04 sq m) 1,000 lbs (450 kg) 10...

  • Page 382

    Trailer and tongue weight always load a trailer with 60% to 65% of the weight in the front of the trailer. This places 10% to 15% of the gross trailer weight (gtw) on the tow hitch of your vehicle. Loads balanced over the wheels or heavier in the rear can cause the trailer to sway severely from side...

  • Page 383

    Note: remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options, or authorized dealer-installed options, must be considered as part of the total load on your vehicle. Refer to the “tire and loading information placard” in “tire s...

  • Page 384

    Warning! (continued) • make certain that the load is secured in the trailer and will not shift during travel. When trailering cargo that is not fully secured, dynamic load shifts can occur that may be difficult for the driver to control. You could lose control of your vehicle and have a collision. •...

  • Page 385

    Towing requirements – tires − do not attempt to tow a trailer while using a compact spare tire. − proper tire inflation pressures are essential to the safe and satisfactory operation of your vehicle. Refer to “tires – general information” in “starting and oper- ating” for proper tire inflation proce...

  • Page 386

    Caution! If the trailer weighs more than 1,000 lbs (454 kg) loaded, it should have its own brakes and they should be of adequate capacity. Failure to do this could lead to accelerated brake lining wear, higher brake pedal effort, and longer stopping distances. Warning! • do not connect trailer brake...

  • Page 387

    The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector. Refer to the following illustrations. Four-pin connector 1 — female pins 4 — park 2 — male pin 5 — left stop/turn 3 — ground 6 — right stop/turn seven-pin connector 1 — battery 5 — ground...

  • Page 388

    Towing tips before setting out on a trip, practice turning, stopping and backing the trailer in an area away from heavy traffic. Manual transmission – if equipped if using a manual transmission vehicle for trailer towing, all starts must be in first gear to avoid excessive clutch slippage. Automatic...

  • Page 389

    Recreational towing (behind motorhome, etc.) towing condition wheels off the ground manual transmission automatic transmission flat tow none • transmission in neutral • key in acc not allowed dolly tow front not allowed ok (fwd only) rear not allowed not allowed on trailer all ok ok 5 starting and o...

  • Page 390

    Note: vehicles equipped with manual transmissions may be recreationally towed (flat towed) at any legal highway speed, for any distance, if the manual transmis- sion is in neutral and the ignition key is in the acc position. Caution! • do not flat tow any vehicle equipped with an automatic transmiss...

  • Page 391: Contents

    What to do in emergencies contents 䡵 hazard warning flashers . . . . . . . . . . . . . . . . 390 䡵 if your engine overheats . . . . . . . . . . . . . . . . 390 䡵 automatic transmission overheating . . . . . . . 391 䡵 jacking and tire changing . . . . . . . . . . . . . . . 392 ▫ jack location . . . ....

  • Page 392

    Hazard warning flashers the hazard warning flasher switch is located on the instrument panel, below the radio. Press the switch to turn on the hazard warning flasher. When the switch is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency. Press the ...

  • Page 393

    Caution! Driving with a hot cooling system could damage your vehicle. If the pointer rises to the h (red) mark, the instrument cluster will sound a chime. When safe, pull over and stop the vehicle with the engine at idle. Turn off the air conditioning and wait until the pointer drops back into the n...

  • Page 394

    Jacking and tire changing warning! • do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel. • being under a jacked-up vehicle is dangerous. The vehicle could slip...

  • Page 395

    Jack location the jack and jack-handle are stowed under the load floor in the cargo area. Spare tire stowage the compact spare tire is stowed under the rear load floor in the cargo area. Spare tire removal lift up the load floor cover and remove the hold down. Preparations for jacking 1. Park the ve...

  • Page 396

    5. Turn off the ignition. 6. Block both the front and rear of the wheel diagonally opposite the jacking position. For example, if changing the right front tire, block the left rear wheel. Note: passengers should not remain in the vehicle while the vehicle is being jacked. Jacking instructions warnin...

  • Page 397

    Warning! (continued) • if working on or near a roadway, be extremely careful of motor traffic. • to assure that spare tires, flat or inflated, are securely stowed, spares must be stowed with the valve stem facing the ground. Caution! Do not attempt to raise the vehicle by jacking on locations other ...

  • Page 398

    Note: refer to “tires — general information” in “starting and operating” for further information about the spare tire, it’s use, and operation. 1. Remove the scissors jack and lug wrench from the spare wheel as an assembly. Turn the jack screw to the left to loosen the lug wrench and remove the wren...

  • Page 399

    For vehicles equipped with plastic trim, the plastic has been cut away to expose the jacking locations in the body. Do not raise the vehicle until you are sure the jack is securely engaged. 3. Turn the jack screw to the left until the jack can be placed under the jacking location. Once the jack is p...

  • Page 400

    5. Remove the wheel nuts and pull the wheel and wheel covers, where applicable, off the hub. Install the spare wheel and wheel nuts with the cone shaped end of the nuts toward the wheel. Lightly tighten the nuts. Warning! To avoid the risk of forcing the vehicle off the jack, do not tighten the whee...

  • Page 401

    Note: the wheel cover is held on the wheel by the wheel nuts. When reinstalling the original wheel, prop- erly align the wheel cover to the valve stem, place the wheel cover onto the wheel, then install the wheel nuts. 6. Lower the vehicle by turning the jack screw to the left. 7. Finish tightening ...

  • Page 402

    Road tire installation vehicles equipped with wheel covers 1. Mount the road tire on the axle. 2. To ease the installation process for steel wheels with wheel covers, install two lug nuts on the mounting studs which are on each side of the valve stem. Install the lug nuts with the cone shaped end of...

  • Page 403

    3. Align the valve notch in the wheel cover with the valve stem on the wheel. Install the cover by hand, snapping the cover over the two lug nuts. Do not use a hammer or excessive force to install the cover. 4. Install the remaining lug nuts with the cone shaped end of the nut toward the wheel. Ligh...

  • Page 404

    Warning! To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts fully until the vehicle is lowered to the ground. Failure to follow this warning may result in personal injury. 3. Lower the vehicle to the ground by turning the jack handle counterclockwise. 4. Finish tighte...

  • Page 405

    Caution! Do not use a portable battery booster pack or any other booster source with a system voltage greater than 12 volts or damage to the battery, starter motor, alternator or electrical system may occur. Warning! Do not attempt jump-starting if the battery is frozen. It could rupture or explode ...

  • Page 406

    Warning! • take care to avoid the radiator cooling fan when- ever the hood is raised. It can start anytime the ignition switch is on. You can be injured by moving fan blades. • remove any metal jewelry such as watch bands or bracelets that might make an inadvertent electrical contact. You could be s...

  • Page 407

    3. If using another vehicle to jump-start the battery, park the vehicle within the jumper cables reach, set the parking brake and make sure the ignition is off. Warning! Do not allow vehicles to touch each other as this could establish a ground connection and personal injury could result. Jump-start...

  • Page 408

    4. Connect the opposite end of the negative (-) jumper cable to a good engine ground (exposed metal part of the discharged vehicle’s engine) away from the battery and the fuel injection system. Warning! Do not connect the cable to the negative post (-) of the discharged battery. The resulting electr...

  • Page 409

    Caution! Accessories that can be plugged into the vehicle power outlets draw power from the vehicle’s battery, even when not in use (i.E., cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent the engin...

  • Page 410

    Caution! • when “rocking” a stuck vehicle by moving be- tween drive and reverse (with automatic transmission) or 1st gear and reverse (with manual transmission), do not spin the wheels faster than 15 mph (24 km/h), or drivetrain damage may result. • revving the engine or spinning the wheels too fast...

  • Page 411

    3. Turn the ignition switch to the on/run position without starting the engine (engine off). 4. Press and maintain firm pressure on the brake pedal. 5. Using a small screwdriver or similar tool, push and hold the override release lever forward. 6. Move the shift lever to the neutral position. 7. The...

  • Page 412

    Towing a disabled vehicle towing condition wheels off the ground automatic transmission manual transmission flat tow none not allowed transmission in neu- tral wheel lift or dolly tow rear not allowed not allowed front fwd models only fwd models only flatbed all best method best method 410 what to d...

  • Page 413

    With ignition key automatic transmission • front wheel drive (fwd) vehicles can be towed with the front wheels elevated or on a flatbed truck (all four wheels off the ground). • four-wheel drive (4wd) vehicles must be towed on a flatbed truck (all four wheels off the ground). Caution! Do not flat to...

  • Page 414

    If the vehicle’s battery is discharged, see “shift lever override” in “what to do in emergencies” for instruc- tions on shifting the automatic transmission out of the park position for towing. Caution! Failure to follow these cautions could result in dam- age to your vehicle: • do not attempt to use...

  • Page 415: Maintaining Your Vehicle

    Maintaining your vehicle contents 䡵 engine compartment — 2.0l . . . . . . . . . . . . . 415 䡵 engine compartment — 2.4l . . . . . . . . . . . . . 416 䡵 onboard diagnostic system — obd ii . . . . . . 417 ▫ loose fuel filler cap message . . . . . . . . . . . 417 䡵 emissions inspection and maintenance ...

  • Page 416

    ▫ exhaust system . . . . . . . . . . . . . . . . . . . . . 429 ▫ cooling system . . . . . . . . . . . . . . . . . . . . . 432 ▫ brake system . . . . . . . . . . . . . . . . . . . . . . . 437 ▫ automatic transmission (cvt) – if equipped . . . . . . . . . . . . . . . . . . 440 ▫ manual transmission – ...

  • Page 417

    Engine compartment — 2.0l 1 — washer fluid reservoir 6 — air cleaner filter 2 — power steering fluid reservoir 7 — coolant pressure cap 3 — engine oil fill 8 — engine oil dipstick 4 — brake fluid reservoir 9 — engine coolant reservoir 5 — integrated power module (fuses) 7 maintaining your vehicle 41...

  • Page 418

    Engine compartment — 2.4l 1 — washer fluid reservoir 6 — air cleaner filter 2 — power steering fluid reservoir 7 — coolant pressure cap 3 — engine oil fill 8 — engine oil dipstick 4 — brake fluid reservoir 9 — engine coolant reservoir 5 — integrated power module (fuses) 416 maintaining your vehicle.

  • Page 419

    Onboard diagnostic system — obd ii your vehicle is equipped with a sophisticated onboard diagnostic system called obd ii. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide ex...

  • Page 420

    Persists, the message will appear the next time the vehicle is started. This might indicate a damaged cap. If the problem is detected twice in a row, the system will turn on the mil. Resolving the problem will turn the mil light off. Emissions inspection and maintenance programs in some localities, ...

  • Page 421

    4. Approximately 15 seconds later, one of two things will happen: a. The mil will flash for about 10 seconds and then return to being fully illuminated until you turn off the ignition or start the engine. This means that your vehicle’s obd ii system is not ready and you should not proceed to the i/m...

  • Page 422

    Dealer service your authorized dealer has the qualified service person- nel, special tools, and equipment to perform all service operations in an expert manner. Service manuals are available which include detailed service information for your vehicle. Refer to these service manuals before attempting...

  • Page 423

    Caution! (continued) • your vehicle has been built with improved fluids that protect the performance and durability of your vehicle and also allow extended maintenance intervals. Do not use chemical flushes in these components as the chemicals can damage your engine, transmission, power steering or ...

  • Page 424

    Caution! Do not overfill the engine. Overfilling the engine will cause oil aeration, which can lead to loss of oil pressure and an increase in oil temperature. This could damage your engine. Also, be sure the oil fill cap is replaced and tightened after adding oil. Change engine oil the oil change i...

  • Page 425

    Caution! Do not use chemical flushes in your engine oil as the chemicals can damage your engine. Such damage is not covered by the new vehicle limited warranty. Engine oil viscosity (sae grade) sae 5w-20 engine oil is recommended for all operating temperatures. This engine oil improves low temperatu...

  • Page 426

    Engine oil filter the engine oil filter should be replaced with a new filter at every engine oil change. Engine oil filter selection all of this manufacturer’s engines have a full-flow type disposable oil filter. Use a filter of this type for replace- ment. The quality of replacement filters varies ...

  • Page 427

    Maintenance-free battery your vehicle is equipped with a maintenance-free battery. You will never have to add water, nor is periodic main- tenance required. Warning! • battery fluid is a corrosive acid solution and can burn or even blind you. Do not allow battery fluid to contact your eyes, skin, or...

  • Page 428

    Caution! • it is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked posi- tive (+) and negative (-) and are identified on the battery case. Cable clamps should b...

  • Page 429

    Warning! • use only refrigerants and compressor lubricants approved by the manufacturer for your air condi- tioning system. Some unapproved refrigerants are flammable and can explode, injuring you. Other unapproved refrigerants or lubricants can cause the system to fail, requiring costly repairs. Re...

  • Page 430

    Hood latching components to ensure proper function. When performing other underhood services, the hood latch, release mechanism and safety catch should be cleaned and lubricated. The external lock cylinders should be lubricated twice a year, preferably in the fall and spring. Apply a small amount of...

  • Page 431

    When refilling the washer fluid reservoir, take some washer fluid and apply it to a cloth or towel and wipe clean the wiper blades, this will help blade performance. To prevent freeze-up of your windshield washer system in cold weather, select a solution or mixture that meets or exceeds the temperat...

  • Page 432

    Warning! • exhaust gases can injure or kill. They contain carbon monoxide (co), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing co, refer to “safety tips/exhaust gas” in “things to know before starting your vehicle” for further...

  • Page 433

    Under normal operating conditions, the catalytic con- verter will not require maintenance. However, it is im- portant to keep the engine properly tuned to assure proper catalyst operation and prevent possible catalyst damage. Note: intentional tampering with emissions control systems can result in c...

  • Page 434

    Cooling system warning! • when working near the radiator cooling fan, dis- connect the fan motor lead or turn the ignition switch to the off position. The fan is temperature controlled and can start at any time the ignition switch is in the on position. • you or others can be badly burned by hot coo...

  • Page 435

    Selection of coolant refer to “fluids, lubricants, and genuine parts” in “maintaining your vehicle” for further information. Caution! • mixing of engine coolant (antifreeze) other than specified hybrid organic additive technology (hoat) engine coolant (antifreeze), may result in engine damage and ma...

  • Page 436

    Vehicle. Please review these recommendations for using hybrid organic additive technology (hoat) engine coolant (antifreeze). When adding engine coolant (antifreeze), a minimum solution of 50% recommended mopar 威 antifreeze/ coolant 5 year/100,000 mile formula hoat (hybrid organic additive technolog...

  • Page 437

    Warning! • the warning words “do not open hot” on the cooling system pressure cap are a safety pre- caution. Never add engine coolant (antifreeze) when the engine is overheated. Do not loosen or remove the cap to cool an overheated engine. Heat causes pressure to build up in the cooling system. To p...

  • Page 438

    Long as the engine operating temperature is satisfactory, the coolant bottle need only be checked once a month. When additional engine coolant (antifreeze) is needed to maintain the proper level, it should be added to the coolant bottle. Do not overfill. Points to remember note: when the vehicle is ...

  • Page 439

    • keep the front of the radiator clean. If your vehicle is equipped with air conditioning, keep the front of the condenser clean. • do not change the thermostat for summer or winter operation. If replacement is ever necessary, install only the correct type thermostat. Other designs may result in uns...

  • Page 440

    When the pads are replaced. However, low fluid level may be caused by a leak and a checkup may be needed. Note: if your vehicle is equipped with a manual transmission , the brake fluid reservoir supplies fluid to both the brake system and the clutch release system. The two systems are separated in t...

  • Page 441

    Warning! (continued) • to avoid contamination from foreign matter or moisture, use only new brake fluid or fluid that has been in a tightly closed container. Keep the master cylinder reservoir cap secured at all times. Brake fluid in a open container absorbs moisture from the air resulting in a lowe...

  • Page 442

    Automatic transmission (cvt) – if equipped selection of lubricant it is important that the proper lubricant is used in the transmission to assure optimum transmission perfor- mance. Use only the manufacturer’s recommended trans- mission fluid which has been formulated with special metal to metal fri...

  • Page 443

    Level checked immediately. Operation with incorrect fluid level can cause severe transmission damage. Fluid and filter changes refer to the “maintenance schedule” for the proper maintenance interval. Manual transmission – if equipped lubricant selection use only the manufacturers recommended transmi...

  • Page 444

    Fill plug. The fluid level should be maintained between the bottom of the fill hole to 1/8 in (4 mm) below the fill hole. Add fluid, if necessary, to maintain the proper level. Frequency of fluid change refer to the “maintenance schedule” for the proper maintenance interval. Power transfer unit (ptu...

  • Page 445

    Hot or cold weather and other extreme conditions will have an adverse effect on paint, metal trim, and under- body protection. The following maintenance recommendations will enable you to obtain maximum benefit from the corrosion resistance built into your vehicle. What causes corrosion? Corrosion i...

  • Page 446

    Caution! • do not use abrasive or strong cleaning materials such as steel wool or scouring powder, which will scratch metal and painted surfaces. • use of power washers exceeding 1,200 psi (8 274 kpa) can result in damage or removal of paint and decals. Special care • if you drive on salted or dusty...

  • Page 447

    Wheel and wheel trim care • all wheels and wheel trim, especially aluminum and chrome plated wheels, should be cleaned regularly with a mild soap and water to prevent corrosion. • to remove heavy soil and/or excessive brake dust, use mopar 威 wheel cleaner or equivalent or select a non-abrasive, non-...

  • Page 448

    Interior care use mopar 威 total clean or equivalent to clean fabric upholstery and carpeting. Use mopar 威 total clean or equivalent to clean vinyl upholstery. Mopar 威 total clean or equivalent is specifically recom- mended for leather upholstery. Your leather upholstery can be best preserved by regu...

  • Page 449

    Glass surfaces all glass surfaces should be cleaned on a regular basis with mopar 威 glass cleaner or any commercial household-type glass cleaner. Never use an abrasive type cleaner. Use caution when cleaning the inside rear win- dow equipped with electric defrosters or the right rear quarter window ...

  • Page 450

    Seat belt maintenance do not bleach, dye or clean the seat belts with chemical solvents or abrasive cleaners. This will weaken the fabric. Sun damage can also weaken the fabric. If the seat belts need cleaning, use a mild soap solution or lukewarm water. Do not remove the seat belts from the car to ...

  • Page 451

    Cavity cartridge fuse mini- fuse description 3 10 amp red rear center brake light switch 4 10 amp red ignition switch/ occupant classifica- tion module 5 20 amp yellow trailer tow – if equipped 6 10 amp red power mirror/ steering control sat- ellite radio/hands- free phone 7 30 amp green ignition of...

  • Page 452

    Cavity cartridge fuse mini- fuse description 18 40 amp green auto shutdown relay 19 20 amp yellow radio amplifiers 20 15 amp lt blue radio 21 10 amp red intrusion module/ siren – if equipped 22 10 amp red heating, ac/ compass 23 15 amp lt blue auto shutdown relay 24 15 amp lt blue power sunroof – if...

  • Page 453

    Cavity cartridge fuse mini- fuse description 33 10 amp red j1962 conn/ powertrain control module 34 30 amp pink antilock brakevalve 35 40 amp green antilock brake pump 36 30 amp pink headlamp/washer control/smart glass – if equipped 37 25 amp natural diesel fuel heater – if equipped caution! • when ...

  • Page 454

    Vehicle storage if you will not be using your vehicle for more than 21 days, you may want to take steps to preserve your battery. • disengage the mini-fuse in the power distribution center labeled iod (ignition off-draw). • or disconnect the negative cable from the battery. • anytime you store your ...

  • Page 455

    Bulb replacement headlamps 1. Raise the hood and locate the connector behind the headlamp. 2. Reach into engine compartment and pull red lock out at connector. 3. Remove the green connector from the back of the bulb by pulling straight back. 4. Twist the bulb to the left. 5. Pull bulb outward from a...

  • Page 456

    License lamps 1. Use a screw driver to gently pry against the side of the snap tab to remove the lamp from the liftgate. 2. Rotate the socket 1/4 turn counterclockwise. 3. Pull the bulb from the socket. Center high-mounted stoplamp this light is an led assembly. See your authorized dealer for replac...

  • Page 457

    Fluids, lubricants, and genuine parts engine component fluid, lubricant, or genuine part engine coolant mopar 威 antifreeze/coolant 5 year/100,000 mile formula hoat (hy- brid organic additive technology) or equivalent. Engine oil use api certified sae 5w-20 engine oil, meeting the requirements of chr...

  • Page 458

    Chassis component fluid, lubricant, or genuine part automatic transmission (cvt) – if equipped mopar 威 cvtf+4威 continuously variable transmission fluid manual transmission – if equipped mopar 威 atf+4威 automatic transmission fluid or equivalent licensed atf+4 威 product. Rear drive assembly (rda) mopa...

  • Page 459: Maintenance Schedules

    Maintenance schedules contents 䡵 maintenance schedule . . . . . . . . . . . . . . . . . . 458 ▫ required maintenance intervals . . . . . . . . . . 460 8 m a i n t e n a n c e s c h e d u l e s.

  • Page 460

    Maintenance schedule the scheduled maintenance services listed in this manual must be done at the times or mileages specified to protect your vehicle warranty and ensure the best vehicle performance and reliability. More frequent main- tenance may be needed for vehicles in severe operating condition...

  • Page 461

    • change your engine oil more often if you drive your vehicle off-road for an extended period of time. • under no circumstances should oil change intervals exceed 8,000 miles (13 000 km) or six months, which- ever comes first. Your authorized dealer will reset the oil change indicator message after ...

  • Page 462

    Once a month • check the tire pressure and look for unusual wear or damage. • inspect the battery and clean and tighten the terminals as required. • check the fluid levels of coolant reservoir, brake master cylinder, and power steering and add as needed. • check all lights and other electrical items...

  • Page 463

    8,000 miles (13,000 km) or 6 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 8,000 miles (13 000 km). Odometer reading date repair order # dealer code signature, authorized ser...

  • Page 464

    24,000 miles (39,000 km) or 18 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 24,000 miles (39 000 km). ❏ inspect the cv joints. ❏ inspect exhaust system. Odometer reading dat...

  • Page 465

    40,000 miles (65,000 km) or 30 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 40,000 miles (65 000 km). Odometer reading date repair order # dealer code signature, authorized ...

  • Page 466

    56,000 miles (91,000 km) or 42 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 56,000 miles (91 000 km). Odometer reading date repair order # dealer code signature, authorized ...

  • Page 467

    72,000 miles (117,000 km) or 54 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 72,000 miles (117 000 km). ❏ inspect the cv joints. ❏ inspect exhaust system. Odometer reading d...

  • Page 468

    88,000 miles (143,000 km) or 66 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 88,000 miles (143 000 km). Odometer reading date repair order # dealer code signature, authorize...

  • Page 469

    96,000 miles (156,000 km) or 72 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 96,000 miles (156 000 km). ❏ replace the engine air cleaner filter. ❏ replace the spark plugs. ❏...

  • Page 470

    104,000 miles (169,000 km) or 78 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 104,000 miles (169 000 km). ❏ flush and replace the engine coolant at 104,000 miles (169 000 km...

  • Page 471

    120,000 miles (195,000 km) or 90 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 120,000 miles (195 000 km). ❏ inspect the cv joints. ❏ inspect exhaust system. ❏ change the aut...

  • Page 472

    136,000 miles (221,000 km) or 102 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 136,000 miles (221 000 km). Odometer reading date repair order # dealer code signature, author...

  • Page 473

    152,000 miles (247,000 km) or 114 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 152,000 miles (247 000 km). Odometer reading date repair order # dealer code signature, author...

  • Page 474

    Warning! • you can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic. • failure to properly inspect and mai...

  • Page 475: Contents

    If you need consumer assistance contents 䡵 suggestions for obtaining service for your vehicle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 475 ▫ prepare for the appointment . . . . . . . . . . . 475 ▫ prepare a list . . . . . . . . . . . . . . . . . . . . . . 475 ▫ be reasonable with r...

  • Page 476

    䡵 department of transportation uniform tire quality grades . . . . . . . . . . . . . . . . . . . . . . . . 481 ▫ treadwear . . . . . . . . . . . . . . . . . . . . . . . . . 481 ▫ traction grades . . . . . . . . . . . . . . . . . . . . . 481 ▫ temperature grades . . . . . . . . . . . . . . . . . . 48...

  • Page 477

    Suggestions for obtaining service for your vehicle prepare for the appointment if you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty. Discuss additional charges with the service manager. ...

  • Page 478

    This is why you should always talk to an authorized dealer’s service manager first. Most matters can be re- solved with this process. • if for some reason you are still not satisfied, talk to the general manager or owner of the authorized dealer- ship. They want to know if you need assistance. • if ...

  • Page 479

    Customer assistance for the hearing or speech impaired (tdd/tty) to assist customers who have hearing difficulties, the manufacturer has installed special tdd (telecommuni- cation devices for the deaf) equipment at its customer center. Any hearing or speech impaired customer, who has access to a tdd...

  • Page 480

    We appreciate that you have made a major investment when you purchased the vehicle. An authorized dealer has also made a major investment in facilities, tools, and training to assure that you are absolutely delighted with the ownership experience. You’ll be pleased with their sincere efforts to reso...

  • Page 481

    If nhtsa receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, nhtsa cannot become involved in individual problems between you, your authorized dealer, and the manufacturer. T...

  • Page 482

    • service manuals these comprehensive service manuals provide the information that students and professional technicians need in diagnosing/troubleshooting, problem solving, maintaining, servicing, and repairing chrysler group llc vehicles. A complete working knowledge of the vehicle, system, and/or...

  • Page 483

    Department of transportation uniform tire quality grades the following tire grading categories were established by the national highway traffic safety administration. The specific grade rating assigned by the tire’s manufacturer in each category is shown on the sidewall of the tires on your vehicle....

  • Page 484

    Temperature grades the temperature grades are a (the highest), b, and c, representing the tire’s resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the mater...

  • Page 485: Index

    Index 10

  • Page 486

    Abs (anti-lock brake system) . . . . . . . . . . . . . . 324 adding engine coolant (antifreeze) . . . . . . . . . . 433 adding fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . 371 adding washer fluid . . . . . . . . . . . . . . . . . . . . . 428 additives, fuel . . . . . . . . . . . . . . ...

  • Page 487

    Automatic transmission . . . . . . . . . . . . . . . . 300,440 fluid and filter changes . . . . . . . . . . . . . . . 441 fluid level check . . . . . . . . . . . . . . . . . . . . 440 fluid type . . . . . . . . . . . . . . . . . . . . . . . . . 440 gear ranges . . . . . . . . . . . . . . . . . . . ....

  • Page 488

    Cargo compartment light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182 luggage carrier . . . . . . . . . . . . . . . . . . . . . 189 cargo light . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182 cargo load floor . . . . . . . . . . . . . . . . . . . . . . . . 185 cargo tie-d...

  • Page 489

    Coolant (antifreeze) . . . . . . . . . . . . . . . . . . . 454,455 cooling system . . . . . . . . . . . . . . . . . . . . . . . . . 432 adding coolant (antifreeze) . . . . . . . . . . . . . 433 coolant level . . . . . . . . . . . . . . . . . . . . 432,435 disposal of used coolant . . . . . . . . . ....

  • Page 490

    Electronic brake control system . . . . . . . . . . . . . 326 anti-lock brake system . . . . . . . . . . . . . . . . 327 brake assist system . . . . . . . . . . . . . . . . . . . 327 electronic roll mitigation . . . . . . . . . . . . . . . 328 traction control system . . . . . . . . . . . . . . . . ...

  • Page 491

    Filters air cleaner . . . . . . . . . . . . . . . . . . . . . . . . . 424 air conditioning . . . . . . . . . . . . . . . . . . . . . 289 engine oil . . . . . . . . . . . . . . . . . . . . . . . 424,455 flashers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 390 hazard warning . . . . . ...

  • Page 492

    Fuel system caution . . . . . . . . . . . . . . . . . . . . . 372 fueling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 371 fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 448 garage door opener (homelink®) . . . . . . . . . . . 161 gas cap (fuel filler cap) . ....

  • Page 493

    Hitches trailer towing . . . . . . . . . . . . . . . . . . . . . . . 378 homelink® (garage door opener) transmitter . . 161 hood release . . . . . . . . . . . . . . . . . . . . . . . . . . 147 ignition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 key . . . . . . . . . . . . . . ....

  • Page 494

    Lead free gasoline . . . . . . . . . . . . . . . . . . . . . . 367 leaks, fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88 life of tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . 353 liftgate (sedan) . . . . . . . . . . . . . . . . . . . . . . . . . . 37 liftgate window...

  • Page 495

    Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . 198 warning (instrument cluster description) . . . 198 loading vehicle . . . . . . . . . . . . . . . . . . . . . . 373,375 capacities . . . . . . . . . . . . . . . . . . . . . . . . . . 375 tires . . . . . . . . . . . . . . . . . . . . ...

  • Page 496

    Outside . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97 rearview . . . . . . . . . . . . . . . . . . . . . . . . . . . 94 vanity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99 modifications/alterations, vehicle . . . . . . . . . . . . . 8 monitor, tire pressure system . . . ...

  • Page 497

    Paint care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 442 panic alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 parking brake . . . . . . . . . . . . . . . . . . . . . . . . . . 321 passing light . . . . . . . . . . . . . . . . . . . . . . . . . . . 152 personal setti...

  • Page 498

    Reminder, seat belt . . . . . . . . . . . . . . . . . . . . . . . 59 remote control door locks . . . . . . . . . . . . . . . . . . . . . . . . . 20 security alarm . . . . . . . . . . . . . . . . . . . . . . . 18 remote keyless entry (sedan) . . . . . . . . . . . . . . . 20 remote sound system (radio...

  • Page 499

    Rear seat . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134 adjustment . . . . . . . . . . . . . . . . . . . . . . . . . 137 heated . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136 lumbar support . . . . . ...

  • Page 500

    Steering power . . . . . . . . . . . . . . . . . . . . . . . . . . 319,320 tilt column . . . . . . . . . . . . . . . . . . . . . . . . 157 steering wheel audio controls . . . . . . . . . . . . . . 275 steering wheel mounted sound system controls . . . . . . . . . . . . . . . . . . . 275 storage . . ...

  • Page 501

    Jacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . 392 life of tires . . . . . . . . . . . . . . . . . . . . . . . . 353 load capacity . . . . . . . . . . . . . . . . . . . . 342,343 pressure monitor system (tpms) . . . . . . . . . 357 pressure warning light . . . . . . . . . . . . . . ...

  • Page 502

    Transmitter battery service (remote keyless entry) . . . . . . . . . . . . . . . . . . . . 25 transmitter, garage door opener (homelink®) . . 161 transporting pets . . . . . . . . . . . . . . . . . . . . . . . . 84 tread wear indicators . . . . . . . . . . . . . . . . . . . . 352 trip computer . . ....

  • Page 503

    Wheel and wheel trim . . . . . . . . . . . . . . . . . . . . 445 wheel and wheel trim care . . . . . . . . . . . . . . . . 445 wind buffeting . . . . . . . . . . . . . . . . . . . . . . . . . 172 window fogging . . . . . . . . . . . . . . . . . . . . . . . . 289 windows . . . . . . . . . . . . . . ....

  • Page 504

    Installation of radio transmitting equipment special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained personnel. The following must be obser...

  • Page 505

    Chrysler group llc 12 mk74-126-ac 3rd edition printed in u.S.A..