1. DL manuals
  2. Jeep
  3. Automobile
  4. 2014 Wrangler
  5. Owner's Manual

Jeep 2014 Wrangler Owner's Manual

Summary of 2014 Wrangler

  • Page 1

    Wrangler chrysler group llc o w n e r ’ s m a n u a l 2014 w r angler 14jk72-126-aa first edition printed in u.S.A. 2 0 1 4.

  • Page 2

    Vehicles sold in canada with respect to any vehicles sold in canada, the name chrysler group llc shall be deemed to be deleted and the name chrysler canada inc. Used in substitution therefore. Driving and alcohol drunken driving is one of the most frequent causes of accidents. Your driving ability c...

  • Page 3: Table Of Contents

    Table of contents section page 1 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 things to know before starting your vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 3 understanding the featu...

  • Page 5: Introduction

    Introduction contents 䡵 introduction . . . . . . . . . . . . . . . . . . . . . . . .4 䡵 rollover warning . . . . . . . . . . . . . . . . . . . .5 䡵 how to use this manual . . . . . . . . . . . . . .6 䡵 warnings and cautions . . . . . . . . . . . . . .8 䡵 vehicle identification number . . . . . . . ....

  • Page 6

    Introduction congratulations on selecting your new chrysler group llc vehicle. Be assured that it represents precision workmanship, distinctive styling, and high quality - all essentials that are traditional to our vehicles. This is a specialized utility vehicle. It can go places and perform tasks t...

  • Page 7

    This owner’s manual has been prepared with the assis- tance of service and engineering specialists to acquaint you with the operation and maintenance of your vehicle. It is supplemented by warranty information, and various customer-oriented documents. Please take the time to read these publications ...

  • Page 8

    Failure to use the driver and passenger seat belts pro- vided is a major cause of severe or fatal injury. In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt. Always buckle up. How to use this manual consult the table of contents to determine...

  • Page 9

    1 introduction 7.

  • Page 10

    Warnings and cautions this owners manual contains warnings against op- erating procedures that could result in a collision or bodily injury. It also contains cautions against proce- dures that could result in damage to your vehicle. If you do not read this entire owners manual, you may miss importan...

  • Page 11

    Vehicle modifications/alterations warning! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a collision resulting in serious injury or death. 1 introduction 9.

  • Page 13: Contents

    Things to know before starting your vehicle contents 䡵 a word about your keys . . . . . . . . . . . . .15 ▫ ignition key removal . . . . . . . . . . . . . . . . . . .15 ▫ key-in-ignition reminder . . . . . . . . . . . . . . . .17 䡵 steering wheel lock — if equipped . . . .17 ▫ to manually lock the s...

  • Page 14

    ▫ remote key unlock on first press . . . . . . . . . .25 ▫ to lock the doors and swing gate . . . . . . . . .26 ▫ sound horn on lock . . . . . . . . . . . . . . . . . . .26 ▫ using the panic alarm . . . . . . . . . . . . . . . . . .27 ▫ to turn off flash lights with lock . . . . . . . . .27 ▫ progra...

  • Page 15

    ▫ child-protection door lock system — rear doors . . . . . . . . . . . . . . . . . . . . . . . . . .43 䡵 windows . . . . . . . . . . . . . . . . . . . . . . . . . . .44 ▫ power windows — if equipped . . . . . . . . . . .44 ▫ wind buffeting . . . . . . . . . . . . . . . . . . . . . . .47 䡵 rear swing...

  • Page 16

    䡵 safety tips . . . . . . . . . . . . . . . . . . . . . . . . .100 ▫ transporting passengers . . . . . . . . . . . . . . . . .100 ▫ exhaust gas . . . . . . . . . . . . . . . . . . . . . . . . .101 ▫ safety checks you should make inside the vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Page 17

    A word about your keys the authorized dealer that sold you your new vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys. Ask your authorized dealer for these numbers and keep them in a safe place. Ignition key removal 1. Place the shift lever in...

  • Page 18

    Warning! • before exiting a vehicle, always apply the parking brake, shift the transmission into park, and re- move the key fob from the ignition. When leaving the vehicle, always lock your vehicle. • never leave children alone in a vehicle, or with access to an unlocked vehicle. • allowing children...

  • Page 19

    Warning! (continued) • do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death. Caution! An unlocked car is an invitation to thieves. Always remove key from the ignition and lock all doors when leaving the vehicle unattended. K...

  • Page 20

    Note: if you turned the wheel to the right to engage the lock, you must turn the wheel slightly to the right to disengage it. If you turned the wheel to the left to engage the lock, turn the wheel slightly to the left to disengage it. Automatic transmission ignition interlock system this system prev...

  • Page 21

    If the vehicle security light turns on during normal vehicle operation (vehicle running for longer than 10 seconds), it indicates that there is a fault in the electron- ics. Should this occur, have the vehicle serviced as soon as possible by an authorized dealer. Caution! The sentry key® immobilizer...

  • Page 22

    Procedure. This procedure consists of programming a blank key to the vehicle electronics. A blank key is one that has never been programmed. Note: when having the sentry key® immobilizer sys- tem serviced, bring all vehicle keys with you to an authorized dealer. Customer key programming if you have ...

  • Page 23

    Note: if a programmed key is lost, see your authorized dealer to have all remaining keys erased from the sys- tem’s memory. This will prevent the lost key from starting your vehicle. The remaining keys must then be reprogrammed. All vehicle keys must be taken to an authorized dealer at the time of s...

  • Page 24

    Note: the panic alarm and the vehicle security alarm are quite different. Please take a moment to activate the panic alarm and the vehicle security alarm to hear the differences in the horn. In case one should go off in the future, you will need to know which mode has been activated in order to deac...

  • Page 25

    Remain in the vehicle and lock the doors with the rke transmitter, once the vehicle security alarm is armed (after 16 seconds), when you pull the door handle to exit, the alarm will sound. If this occurs, press the unlock button on the rke transmitter to disarm the vehicle security alarm. You may al...

  • Page 26

    • the illuminated entry system will not operate if the dimmer control is in the “dome defeat” position (extreme bottom position). Remote keyless entry (rke) — if equipped this system allows you to lock or unlock the doors, swing gate, and activate the panic alarm from a maxi- mum distance of 66 ft (...

  • Page 27

    To unlock the doors and swing gate press and release the rke transmitter unlock button once to unlock the driver’s door only, or twice to unlock all the doors and swing gate. When the rke transmitter unlock button is pressed, the illuminated entry will initiate and the turn signal lights will flash ...

  • Page 28

    Note: pressing the rke transmitter lock button while you are inside of the vehicle will activate the vehicle security alarm. Opening a door with the vehicle security alarm activated will cause the alarm to sound. Press the rke transmitter unlock button to deactivate the ve- hicle security alarm. 5. ...

  • Page 29

    • for vehicles not equipped with the evic, perform the following steps: 1. Press the rke transmitter lock button for 4 to 10 seconds. 2. While the lock button is pressed (after four seconds), press the rke transmitter panic button. Release both buttons. The “sound horn on lock” feature can be reacti...

  • Page 30

    • for vehicles not equipped with the evic, perform the following steps: 1. Press the rke transmitter unlock button for 4 to 10 seconds. 2. While the unlock button is pressed, (after four seconds) press the rke transmitter lock button. Release both buttons. 3. Test the “flash lights with lock” featur...

  • Page 31

    2. Remove and replace the battery. Avoid touching the new battery with your fingers. Skin oils may cause battery deterioration. If you touch a battery, clean it with rubbing alcohol. 3. To reassemble the rke transmitter case, snap the two halves together. General information this device complies wit...

  • Page 32

    2. Closeness to a radio transmitter such as a radio station tower, airport transmitter, and some mobile or cb radios. Remote starting system — if equipped this system uses the remote keyless entry (rke) transmitter to start the engine conve- niently from outside the vehicle while still maintaining s...

  • Page 33

    Warning! • do not start or run an engine in a closed garage or confined area. Exhaust gas contains carbon mon- oxide (co) which is odorless and colorless. Carbon monoxide is poisonous and can cause serious in- jury or death when inhaled. • keep remote keyless entry (rke) transmitters away from child...

  • Page 34

    Note: • the park lamps will turn on and remain on during remote start mode. • for security, power window operation is disabled when the vehicle is in the remote start mode. • the engine can be started two consecutive times (two 15-minute cycles) with the rke transmitter. However, the ignition switch...

  • Page 35

    Note: the ignition switch must be in the on/run position in order to drive the vehicle. Doors caution! Careless handling and storage of the removable door panels may damage the seals, causing water to leak into the vehicle’s interior. Upper half door window removal — if equipped grasp the half door ...

  • Page 36

    Upper half door window installation — if equipped 1. Grasp the half door window and line up the pins with the pockets in the lower door. 2. Push down to ensure the half door window is fully seated. Front door removal warning! Do not drive your vehicle on public roads with the doors removed as you wi...

  • Page 37

    3. Unplug the wiring harness connector under the instru- ment panel by pressing the tab at the top of the connector and pulling to disconnect. Note: if the red latch on the connector is locked, pull the red latch down. This will unlock the connector tab, allowing the tab to be pressed down and enabl...

  • Page 38

    4. Unhook the door strap from the body hook. Be careful not to allow the door to swing fully open as the mirror may damage the paint. 5. With the door open, lift the door to clear the hinge pins from their hinges and remove the door. Note: doors are heavy; use caution when removing them. To reinstal...

  • Page 39

    1. Roll down the glass window to prevent any damage. 2. Remove the hinge pin screws from the upper and lower outside hinges (using a #t50 torx® head driver). Note: the hinge pin screws and nuts can be stowed in the rear cargo tray located under the rear loadfloor. 3. Slide the front seat(s) fully fo...

  • Page 40

    5. Unplug the wiring harness connector. Note: if the red latch on the connector is locked, push the red latch to the right until you can only see the latch on one end (right) of the connector. This will unlock the connector tab, allowing the tab to be pressed down and enabling the harness to be disc...

  • Page 41

    6. Unhook the door strap from the body hook. 7. With the door open, lift the door to clear the hinge pins from their hinges and remove the door. Note: doors are heavy; use caution when removing them. To reinstall the door(s), perform the previous steps in the opposite order. Door locks manual door l...

  • Page 42

    Note: the ignition key that is used to start the vehicle is used to lock or unlock the doors, swing gate, glove compartment, and console storage. Warning! • for personal security reasons and safety in a colli- sion, lock the vehicle doors when you drive, as well as when you park and leave the vehicl...

  • Page 43

    Power door locks — if equipped the power door lock switch is located on each front door panel. Press the switch forward to lock the doors, and rearward to unlock the doors. Warning! • for personal security reasons and safety in a colli- sion, lock the vehicle doors when you drive, as well as when yo...

  • Page 44

    Automatic door locks — if equipped the auto door lock feature default condition is enabled. When enabled, the door locks will lock automatically when the vehicle’s speed exceeds 15 mph (24 km/h). The auto door lock feature can be enabled or disabled by your authorized dealer per written request of t...

  • Page 45

    Child-protection door lock system — rear doors to provide a safer environment for small children riding in the rear seats, the rear doors are equipped with child-protection door lock system. To engage or disengage the child-protection door lock system 1. Open the rear door. 2. Insert the tip of the ...

  • Page 46

    Note: for emergency exit with the system engaged, move the rocker lever rearward (unlocked position), roll down the window and open the door with the outside door handle. Windows power windows — if equipped the power window switches are located on the instru- ment panel below the radio. Press the sw...

  • Page 47

    Note: • for vehicles not equipped with the electronic vehicle information center (evic), the power window switches will remain active for 45 seconds after the ignition switch is turned to the lock position. Open- ing either front door will cancel this feature. • for vehicles equipped with the evic, ...

  • Page 48

    Window lockout switch — four-door models the window lockout switch (located between the front window switches) allows you to disable the rear window switches that are located on the back of the center floor console. To disable the window controls, press the win- dow lockout button downward. To enabl...

  • Page 49

    Rear power windows — four-door models the rear passenger window switches are located on the back of the center floor console. Press the switch down- ward to open the window and upward to close the window. Wind buffeting wind buffeting can be described as the perception of pressure on the ears or a h...

  • Page 50

    Note: close the rear flip-up window before attempting to close the swing gate (hard top models only). Caution! Do not press on rear wiper blade when closing the rear flip-up window, as damage to the blade will result. Warning! Driving with the flip-up window open can allow poisonous exhaust gases in...

  • Page 51

    Occupant restraints some of the most important safety features in your vehicle are the restraint systems: • three-point lap and shoulder belts for the driver and all passengers • advanced front air bags for driver and front passen- ger • supplemental seat-mounted side air bags (sab) — if equipped • ...

  • Page 52

    Note: the advanced front air bags have a multistage inflator design. This allows the air bag to have different rates of inflation based on several factors, including the severity and type of collision. Here are some simple steps you can take to minimize the risk of harm from a deploying air bag: 1. ...

  • Page 53

    3. The driver and front passenger seats should be moved back as far as practical to allow the advanced front air bags room to inflate. 4. Do not lean against the door or window. If your vehicle has side air bags, and deployment occurs, the side air bags will inflate forcefully into the space between...

  • Page 54

    Warning! (continued) • in a collision, you and your passengers can suffer much greater injuries if you are not properly buck- led up. You can strike the interior of your vehicle or other passengers, or you can be thrown out of the vehicle. Always be sure you and others in your vehicle are buckled up...

  • Page 55

    Warning! • it is dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • be sure ever...

  • Page 56

    2. The seat belt latch plate is above the back of the front seat and next to your arm in the rear seat. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to allow the belt to go around your lap. 3. When the belt is long enough to fit, insert the la...

  • Page 57

    Warning! • a belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • a belt that is too loose will not protect you prop- erly. In a sudden st...

  • Page 58

    4. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision. Not...

  • Page 59

    Warning! • a lap belt worn too high can increase the risk of injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdo- men. Always wear the lap part of your seat belt as low as possible and keep it snug. • a twisted belt may not protect you properly. I...

  • Page 60

    Rear center lap/shoulder belt retractor lockout — four-door models only this feature is designed to lock the retractor whenever the 60% rear seatback is not fully latched. This prevents someone from wearing the rear center lap/shoulder belt when the rear seatback is not fully latched. Note: • if the...

  • Page 61

    2. At about 6 to 12 in (15 to 30 cm) above the latch plate, grasp and twist the belt webbing 180 degrees to create a fold that begins immediately above the latch plate. 3. Slide the latch plate upward over the folded webbing. The folded webbing must enter the slot at the top of the latch plate. 4. C...

  • Page 62

    Warning! (continued) effectiveness of the seat belt and increase the risk of injury in a collision. As a guide, if you are shorter than average, you will prefer a lower position, and if you are taller than average, you will prefer a higher position. When you release the anchorage, try to move it up ...

  • Page 63

    Out only the amount of webbing necessary to comfort- ably wrap around the occupant’s mid-section. Slide the latch plate into the buckle until you hear a ⬙ click. ⬙ automatic locking retractor mode (alr) — if equipped in this mode, the shoulder belt is automatically pre- locked. The belt will still r...

  • Page 64

    Warning! • the belt and retractor assembly must be replaced if the seat belt assembly automatic locking retractor (alr) feature or any other seat belt function is not working properly when checked according to the procedures in the service manual. • failure to replace the belt and retractor assembly...

  • Page 65

    Enhanced seat belt use reminder system (beltalert®) beltalert® is a feature intended to remind the driver and front passenger (if equipped with front passenger beltalert®) to fasten their seat belts. The feature is active whenever the ignition is on. If the driver or front seat passenger is unbelted...

  • Page 66

    Seat belts and pregnant women we recommend that pregnant women use seat belts throughout their pregnancy. Keeping the mother safe is the best way to keep the baby safe. Pregnant women should wear the lap part of the belt across the thighs and as snug across the hips as possible. Keep the belt low so...

  • Page 67

    Note: the driver and passenger advanced front air bags are certified to new federal regulations. The advanced front air bags have a multistage inflator design. This allows the air bag to have different rates of inflation that are based on several factors, including the severity and type of collision...

  • Page 68

    Note: • air bag covers may not be obvious in the interior trim, but they will open during air bag deployment. • after any collision, the vehicle should be taken to an authorized dealer immediately. Air bag system components your vehicle may be equipped with the following air bag system components: •...

  • Page 69

    Warning! • no objects should be placed over or near the air bag on the instrument panel, because any such objects could cause harm if the vehicle is in a collision severe enough to cause the air bag to inflate. • do not put anything on or around the air bag covers or attempt to open them manually. Y...

  • Page 70

    Warning! (continued) • do not drill, cut or tamper with the knee bolster in any way. • do not mount any accessories to the knee bolster such as alarm lights, stereos, citizen band radios, etc. Supplemental seat-mounted side air bags (sab) — if equipped supplemental seat-mounted side air bags (sab) m...

  • Page 71

    Note: • air bag covers may not be obvious in the interior trim, but they will open during air bag deployment. • being too close to the sab during deployment could cause you to be severely injured or killed. Sab air bags are a supplement to the seat belt restraint system. Occupants, including childre...

  • Page 72

    The orc determines if deployment of the front and/or side air bags is required in a frontal or side collision. Based on the impact sensor’s signals, a central electronic orc deploys the advanced front air bags, supplemen- tal seat-mounted side air bags (sab) — if equipped, and front seat belt preten...

  • Page 73

    The orc contains a backup power supply system that may deploy the air bags even if the battery loses power or it becomes disconnected prior to deployment. Also, the orc turns on the air bag warning light for four to eight seconds for a self-check when the ignition is first turned on. After the self-...

  • Page 74

    Are possible, based on several factors, including the collision type and severity. The steering wheel hub trim cover and the upper right side of the instrument panel separate and fold out of the way as the air bags inflate to their full size. The air bags fully inflate in about 50 to 70 milliseconds...

  • Page 75

    Enhanced accident response system in the event of an impact causing air bag deployment, if the communication network remains intact, and the power remains intact, depending on the nature of the event the orc will determine whether to have the enhanced accident response system perform the follow- ing...

  • Page 76

    They are not permanent and normally heal quickly. However, if you haven’t healed significantly within a few days, or if you have any blistering, see your doctor immediately. • as the air bags deflate you may see some smoke-like particles. The particles are a normal by-product of the process that gen...

  • Page 77

    Warning! (continued) • do not attempt to modify any part of your air bag system. The air bag may inflate accidentally or may not function properly if modifications are made. Take your vehicle to an authorized dealer for any air bag system service. If your seat, including your trim cover and cushion,...

  • Page 78

    Warning! (continued) • it is dangerous to try to repair any part of the air bag system yourself. Be sure to tell anyone who works on your vehicle that it has an air bag system. Air bag warning light you will want to have the air bags ready to inflate for your protection in a collision. The air bag w...

  • Page 79

    Assist in understanding how a vehicle’s systems per- formed. The edr is designed to record data related to vehicle dynamics and safety systems for a short period of time, typically 30 seconds or less. The edr in this vehicle is designed to record such data as: • how various systems in your vehicle w...

  • Page 80

    That small children ride in proper restraint systems. This is the law, and you can be prosecuted for ignoring it. Children 12 years or younger should ride properly buckled up in a rear seat, if available. According to crash statistics, children are safer when properly restrained in the rear seats ra...

  • Page 81

    Summary of recommendations for restraining children in vehicles child size, height, weight or age recommended type of child restraint infants and toddlers children who are two years old or younger and who have not reached the height or weight limits of their child re- straint either an infant carrie...

  • Page 82

    Infants and child restraints safety experts recommend that children ride rearward- facing in the vehicle until they are two years old or until they reach either the height or weight limit of their rear facing child safety seat. Two types of child restraints can be used rearward-facing: infant carrie...

  • Page 83

    Have outgrown the rear-facing weight or height limit of their rear-facing convertible child seat. Children should remain in a forward-facing child seat with a harness for as long as possible, up to the highest weight or height allowed by the child seat. All children whose weight or height is above t...

  • Page 84

    Children too large for booster seats children who are large enough to wear the shoulder belt comfortably, and whose legs are long enough to bend over the front of the seat when their back is against the seatback, should use the seat belt in a rear seat. Use this simple 5-step test to decide whether ...

  • Page 85

    Recommendations for attaching child restraints restraint type combined weight of the child + child restraint use any attachment method shown with an “x” below latch – lower anchors only seat belt only latch – lower anchors + top tether anchor seat belt + top tether anchor rear-facing child restraint...

  • Page 86

    Lower anchors and tethers for children (latch) restraint system your vehicle is equipped with the child restraint anchor- age system called latch, which stands for lower anchors and tethers for children. The latch system has three vehicle anchor points for installing latch- equipped child seats. The...

  • Page 87

    Latch positions for installing child restraints in this vehicle latch positions (two-door models) lower anchorage symbol 2 anchorages per seating position top tether anchorage symbol latch positions (four-door models) lower anchorage symbol 2 anchorages per seating position top tether anchorage symb...

  • Page 88

    What is the weight limit (child’s weight + weight of the child restraint) for using the latch anchorage system to attach the child restraint? 65 lbs (29.5 kg) use the latch anchorage system until the combined weight of the child and the child restraint is 65 lbs (29.5 kg). Use the seat belt and teth...

  • Page 89

    Can two child restraints be attached using a common lower latch anchorage? No never “share” a latch anchorage with two or more child restraints. If the center position does not have dedicated latch lower anchorages, use the seat belt to in- stall a child seat in the center position next to a child s...

  • Page 90

    Locating the latch anchorages the lower anchorages are round bars that are found at the rear of the seat cushion where it meets the seatback, below the anchorage sym- bols on the seatback. They are just visible when you lean into the rear seat to install the child restraint. You will easily feel the...

  • Page 91

    Locating the latch anchorages in addition, there are tether strap anchors lo- cated behind each rear seatback, near to the floor. Latch anchorages (four-door models) tether strap mounting (two-door models) 2 things to know before starting your vehicle 89.

  • Page 92

    Latch-compatible child restraint systems will be equipped with a rigid bar or a flexible strap on each side. Each will have a hook or connector to attach to the lower anchorage and a way to tighten the connection to the anchorage. Forward-facing child restraints and some rear-facing infant restraint...

  • Page 93

    Warning! Never use the same lower anchorage to attach more than one child restraint. If you are installing latch- compatible child restraints next to each other, you must use the seat belt for the center position. You can then use either the latch anchors or the vehicle’s seat belt for installing ch...

  • Page 94

    4. Attach the lower hooks or connectors of the child restraint to the lower anchorages in the selected seat- ing position. 5. If the child restraint has a tether strap, connect it to the top tether anchorage. See the section “installing child restraints using the top tether anchorage” for direc- tio...

  • Page 95

    Warning! • improper installation of a child restraint to the latch anchorages can lead to failure of an infant or child restraint. The child could be badly injured or killed. Follow the manufacturer’s directions ex- actly when installing an infant or child restraint. • child restraint anchorages are...

  • Page 96

    Lap/shoulder belt systems for installing child restraints in this vehicle two-door models four-door models 94 things to know before starting your vehicle.

  • Page 97

    What is the weight limit (child’s weight + weight of the child re- straint) for using the tether anchor with the seat belt to attach a forward facing child restraint? Weight limit of the child restraint always use the tether anchor when using the seat belt to install a for- ward facing child restrai...

  • Page 98

    Installing a child restraint with a switchable automatic locking retractor (alr) 1. Place the child seat in the center of the seating position. For some second row seats, you may need to recline the seat and/or raise the head restraint to get a better fit. If the rear seat can be moved forward and r...

  • Page 99

    Strap. See the section “installing child restraints using the top tether anchorage” for directions to attach a tether anchor. 9. Test that the child restraint is installed tightly by pulling back and forth on the child seat at the belt path. It should not move more than 1 inch (25.4 mm) in any direc...

  • Page 100

    4. Remove slack in the tether strap according to the child restraint manufacturer’s instructions. Tether strap mounting (two-door models) tether strap mounting (four-door models) 98 things to know before starting your vehicle.

  • Page 101

    Warning! • an incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchorage position directly behind the child seat to secure a child restraint top tether strap. • if your vehicle is equipped with a split rear seat, make sure the tethe...

  • Page 102

    “maintenance procedures” in “maintaining your ve- hicle”. Non-detergent or straight mineral oils must never be used. A new engine may consume some oil during its first few thousand miles (kilometers) of operation. This should be considered a normal part of the break-in and not inter- preted as an in...

  • Page 103

    Exhaust gas warning! Exhaust gases can injure or kill. They contain carbon monoxide (co), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing (co), follow these safety tips: • do not run the engine in a closed garage or in confined...

  • Page 104

    Safety checks you should make inside the vehicle seat belts inspect the belt system periodically, checking for cuts, frays, and loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Front seat belt assemblies must be replaced after a collision. Rear seat b...

  • Page 105

    Warning! Pedals that cannot move freely can cause loss of vehicle control and increase the risk of serious per- sonal injury. • always make sure that floor mats are properly attached to the floor mat fasteners. • never place or install floor mats or other floor coverings in the vehicle that cannot b...

  • Page 106

    Periodic safety checks you should make outside the vehicle tires examine tires for excessive tread wear and uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread or sidewall. Inspect the tread for cuts and cracks. Inspect sidewalls for cuts, cracks and bulges. Ch...

  • Page 107: Contents

    Understanding the features of your vehicle contents 䡵 mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . .111 ▫ inside day/night mirror . . . . . . . . . . . . . . . .111 ▫ outside mirrors . . . . . . . . . . . . . . . . . . . . . .111 ▫ automatic dimming mirror — if equipped . . .112 ▫ p...

  • Page 108

    ▫ delete/erase “all” uconnect® phonebook entries . . . . . . . . . . . . . . . . . . . . . . . . . . . . .123 ▫ list all names in the uconnect® phonebook . . .124 ▫ phone call features . . . . . . . . . . . . . . . . . . .124 ▫ uconnect® phone features . . . . . . . . . . . . . .127 ▫ advanced phone...

  • Page 109

    ▫ 60/40 split folding rear seat — four-door models . . . . . . . . . . . . . . . . . . . . . . . . . . . .163 䡵 to open and close the hood . . . . . . . . .165 䡵 lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . .166 ▫ multifunction lever . . . . . . . . . . . . . . . . . . . .166 ▫ hea...

  • Page 110

    ▫ to deactivate . . . . . . . . . . . . . . . . . . . . . . . .180 ▫ to resume speed . . . . . . . . . . . . . . . . . . . . .180 ▫ to vary the speed setting . . . . . . . . . . . . . . .180 ▫ to accelerate for passing . . . . . . . . . . . . . . . .181 䡵 electrical power outlet . . . . . . . . . . ...

  • Page 111

    ▫ front panel(s) installation with rear hard top removed . . . . . . . . . . . . . . . . . . . . . . . . . . .210 ▫ rear hard top removal . . . . . . . . . . . . . . . .210 ▫ rear hard top installation . . . . . . . . . . . . . . .213 䡵 door frame. . . . . . . . . . . . . . . . . . . . . . . . .214 ...

  • Page 112

    ▫ lowering the windshield and removing side bars . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .290 ▫ raising the windshield and replacing side bars . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .293 䡵 rear window features — hard top only . . . . . . . . . . . . . . . . ....

  • Page 113

    Mirrors inside day/night mirror a single ball joint mirror is provided in the vehicle. It is a twist on mirror that has a fixed position at the wind- shield. The mirror installs on the windshield button with a counterclockwise rotation and requires no tools for mounting. The mirror head can be adjus...

  • Page 114

    Warning! Vehicles and other objects seen in the passenger side convex mirror will look smaller and farther away than they really are. Relying too much on your (continued) warning! (continued) passenger side mirror could cause you to collide with another vehicle or other object. Use your inside mirro...

  • Page 115

    Caution! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror. Apply the solution onto a clean cloth and wipe the mirror clean. Power mirrors — if equipped the power mirror switch is located on the center of the instrument panel, below the climate...

  • Page 116

    After selecting a mirror, move the knob in the same direction you want the mirror to move. Use the center off position to guard against accidentally moving a mirror position. Heated mirrors — if equipped these mirrors are heated to melt frost or ice. This feature can be activated whenever you turn o...

  • Page 117

    Mobile phone’s audio is transmitted through your vehi- cle’s audio system; the system will automatically mute your radio when using the uconnect® phone. Note: the uconnect® phone requires a mobile phone equipped with the bluetooth® “hands-free profile,” version 0.96 or higher. See the uconnect® webs...

  • Page 118

    Warning! (continued) laws, including laws regarding phone use. Your at- tention should be focused on safely operating the vehicle. Failure to do so may result in a collision causing serious injury or death. Uconnect® phone button the radio or steering wheel controls (if equipped) will contain the tw...

  • Page 119

    Operation voice commands can be used to operate the uconnect® phone and to navigate through the uconnect® phone menu structure. Voice commands are required after most uconnect® phone prompts. You will be prompted for a specific command and then guided through the available options. • prior to giving...

  • Page 120

    To activate the uconnect® phone from idle, simply press the button and follow the audible prompts for direc- tions. All uconnect® phone sessions begin with a press of the button on the radio control head. Cancel command at any prompt, after the beep, you can say “cancel” and you will be returned to ...

  • Page 121

    • you will then be asked to give your mobile phone a priority level between one and seven, with one being the highest priority. You can pair up to seven mobile phones to your uconnect® phone. However, at any given time, only one mobile phone can be in use, connected to your uconnect® system. The pri...

  • Page 122

    Or downloaded phonebook. To learn how to store a name in the phonebook, refer to “add names to your uconnect® phonebook,” in the phonebook. • the uconnect® system will confirm the name and then dial the corresponding phone number, which may appear in the display of certain radios. Phonebook download...

  • Page 123

    • this downloaded phonebook cannot be edited or deleted on the uconnect® phone. These can only be edited on the mobile phone. The changes are trans- ferred and updated to uconnect® phone on the next phone connection. Add names to your uconnect® phonebook note: adding names to the uconnect® phonebook...

  • Page 124

    Edit uconnect® phonebook entries • press the button to begin. • after the “ready” prompt and the following beep, say “phonebook edit.” • you will then be asked for the name of the phonebook entry that you wish to edit. • next, choose the number designation (home, work, mobile, or other) that you wis...

  • Page 125

    • after the “ready” prompt and the following beep, say “phonebook delete.” • after you enter the phonebook delete menu, you will then be asked for the name of the entry that you wish to delete. You can either say the name of a phonebook entry that you wish to delete or you can say “list names” to he...

  • Page 126

    List all names in the uconnect® phonebook • press the button to begin. • after the “ready” prompt and the following beep, say “phonebook list names.” • the uconnect® phone will play the names of all the phonebook entries, including the downloaded phone- book entries, if available. • to call one of t...

  • Page 127

    Answer or reject an incoming call — call currently in progress if a call is currently in progress and you have another incoming call, you will hear the same network tones for call waiting that you normally hear when using your mobile phone. Press the button to place the current call on hold and answ...

  • Page 128

    Conference call when two calls are in progress (one active and one on hold), press and hold the button until you hear a double beep indicating that the two calls have been joined into one conference call. Three-way calling to initiate three-way calling, press the button while a call is in progress, ...

  • Page 129

    Call continuation call continuation is the progression of a phone call on the uconnect® phone after the vehicle ignition has been switched to off. Call continuation functionality avail- able on the vehicle can be any one of three types: 1. After the ignition is switched to off, a call can continue o...

  • Page 130

    Emergency assistance if you are in an emergency and the mobile phone is reachable: • pick up the phone and manually dial the emergency number for your area. If the phone is not reachable and the uconnect® phone is operational, you may reach the emergency number as follows: • press the button to begi...

  • Page 131

    Warning! To use your uconnect® phone system in an emer- gency, your mobile phone must be: • turned on, • paired to the uconnect® system, • and have network coverage. Roadside assistance/towing assistance if you need roadside assistance: • press the button to begin. • after the “ready” prompt and the...

  • Page 132

    Working with automated systems this method is used in instances where one generally has to press numbers on the mobile phone keypad while navigating through an automated telephone system. You can use your uconnect® phone to access a voice mail system or an automated service, such as a paging service...

  • Page 133

    Barge in – overriding prompts the “voice command” button can be used when you wish to skip part of a prompt and issue your voice command immediately. For example, if a prompt is asking “would you like to pair a phone, clear a...,” you could press the button and say, “pair a phone” to select that opt...

  • Page 134

    Note: certain brands of mobile phones do not send the dial ring to the uconnect® phone to play it on the vehicle audio system, so you will not hear it. Under this situa- tion, after successfully dialing a number the user may feel that the call did not go through even though the call is in progress. ...

  • Page 135

    If you would like to connect or disconnect the bluetooth® connection between a uconnect® phone paired mobile phone and the uconnect® phone, follow the instructions described in your mobile phone user’s manual. List paired mobile phone names • press the button to begin. • after the “ready” prompt and...

  • Page 136

    Delete uconnect® phone paired mobile phones • press the button to begin. • after the “ready” prompt and the following beep, say “setup phone pairing.” • at the next prompt, say “delete” and follow the prompts. • you can also press the button at any time while the list is being played, and then choos...

  • Page 137

    Best results, the voice training session should be com- pleted when the vehicle is parked with the engine running, all windows closed, and the blower fan switched off. This procedure may be repeated with a new user. The system will adapt to the last trained voice only. Reset • press the button. • af...

  • Page 138

    • even though the system is designed for users speaking in north american english, french, and spanish ac- cents, the system may not always work for some. • when navigating through an automated system such as voice mail, or when sending a page, at the end of speaking the digit string, make sure to s...

  • Page 139

    • performance, such as audio clarity, echo, and loudness to a large degree rely on the phone and network, and not the uconnect® phone. • echo at the phone far end can sometimes be reduced by lowering the in-vehicle audio volume. • in a convertible vehicle, system performance may be compromised with ...

  • Page 140

    Send messages: you can send messages using uconnect® phone. To send a new message: • press the button. • after the “ready” prompt and the following beep, say “sms send” or “send messages.” • you can either say the message you wish to send or say “list messages.” there are 20 preset messages. To send...

  • Page 141

    16. Can this wait? 17. Bye for now 18. When can we meet 19. Send number to call 20. Start without me turn sms incoming announcement on/off turning the sms incoming announcement off will stop the system from announcing the new incoming mes- sages. • press the button. • after the “ready” prompt and th...

  • Page 142

    140 understanding the features of your vehicle.

  • Page 143

    3 understanding the features of your vehicle 141.

  • Page 144

    142 understanding the features of your vehicle.

  • Page 145

    Voice commands primary alternate (s) zero one two three four five six seven eight nine star (*) plus (+) pound (#) add location voice commands primary alternate (s) all call cancel confirmation prompts continue delete dial download edit emergency english erase all espanol francais 3 understanding th...

  • Page 146

    Voice commands primary alternate (s) help home language list names list phones mobile mute mute off new entry no other pair a phone phone pairing pairing phonebook phone book voice commands primary alternate (s) previous record again redial return to main menu return or main menu select phone select...

  • Page 147

    General information this device complies with part 15 of the fcc rules and rss 210 of industry canada. Operation is subject to the following conditions: • changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment....

  • Page 148

    Warning! Any voice commanded system should be used only in safe driving conditions following all applicable laws, including laws regarding phone use. Your at- tention should be focused on safely operating the vehicle. Failure to do so may result in a collision causing serious injury or death. When y...

  • Page 149

    To hear the first available menu, press the voice com- mand button and say “help” or “main menu.” commands the voice command system understands two types of commands, universal commands and local commands. Universal commands are available at all times. Local commands are available if the supported r...

  • Page 150

    • “bluetooth streaming” (to switch to bluetooth® streaming mode) • “memo” (to switch to the memo recorder) • “system setup” (to switch to system setup) radio am to switch to the am band, say “am” or “radio am.” in this mode, you may say the following commands: • “frequency #” (to change the frequenc...

  • Page 151

    • “next channel” (to select the next channel) • “previous channel” (to select the previous channel) • “list channel” (to hear a list of available channels) • “select name” (to say the name of a channel) • “menu radio” (to switch to the radio menu) • “main menu” (to switch to the main menu) disc mode...

  • Page 152

    Memo mode to switch to the voice recorder mode, say “memo.” in this mode, you may say the following commands: • “new memo” (to record a new memo) — during the recording, you may press the voice command button to stop recording. You proceed by saying one of the following commands: – “save” (to save t...

  • Page 153

    • “tutorial” • “voice training” note: keep in mind that you have to press the voice command button first and wait for the beep before speaking the “barge in” commands. Voice training for users experiencing difficulty with the system recog- nizing their voice commands or numbers the uconnect® voice “...

  • Page 154

    Warning! (continued) • do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. In a collision, people riding in these areas are more likely to be seriously injured or killed. • be sure everyone in your vehicle is in a seat and using a seat belt properl...

  • Page 155

    Warning! • adjusting a seat while driving may be dangerous. Moving a seat while driving could result in loss of control which could cause a collision and serious injury or death. • seats should be adjusted before fastening the seat belts and while the vehicle is parked. Serious injury or death could...

  • Page 156

    Warning! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt, which could result in serious injury or death. Front passenger easy entry seat — two-door models pull upward on the recline lever (to...

  • Page 157

    To return the seat to a sitting position, rotate the seatback upright until it locks and push the seat rearward until the track locks. Note: • the front passenger seats have a track memory, which returns the seat to just past the halfway point of the track regardless of its original position. • the ...

  • Page 158

    Rotate the entire seat assembly toward the instrument panel. Passenger seat in addition to easy entry, the front passenger seat is also equipped with tip n’ slide™. This feature allows for easier entry for rear passengers. Recline lever tip n’ slide™ 156 understanding the features of your vehicle.

  • Page 159

    Pull upward on the recline lever and slide the entire seat forward (easy entry). With the seat forward, pull the entire seat assembly toward the instrument panel. Heated seats — if equipped on some models, the front driver and passenger seats may be equipped with heaters in both the seat cushions an...

  • Page 160

    Controls for each seat are located on a switch bank near the bottom center of the instrument panel. You can choose from high, low or off heat settings. Amber indicator lights in each switch indicate the level of heat in use. Two indicator lights will illuminate for high, one for low and none for off...

  • Page 161

    Warning! (continued) • do not place anything on the seat or seatback that insulates against heat, such as a blanket or cushion. This may cause the seat heater to overheat. Sitting in a seat that has been overheated could cause serious burns due to the increased surface tempera- ture of the seat. Hea...

  • Page 162

    Rear head restraints the rear seat is equipped with nonadjustable head re- straints. Refer to “occupant restraints” in “things to know before starting your vehicle” for information on child seat tether routing. Fold and tumble rear seat — two-door models note: • prior to folding the rear seat, it ma...

  • Page 163

    2. Slowly flip the entire seat forward. 3. Return the seat to the normal position. 4. Raise the rear seatback using the assist strap and firmly lock the seat into position. Rear seat release folding rear seat 3 understanding the features of your vehicle 161.

  • Page 164

    Removing the rear seat — two-door models warning! • it is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • do not allow people to ride in any area of your vehicle that is not...

  • Page 165

    Replacing the rear seat — two-door models reverse the steps for removing the seat. Warning! • to help protect against personal injury, passengers should not be seated in the rear cargo area with the rear seat folded down or removed from the vehicle. • the rear cargo space is intended for load carryi...

  • Page 166

    To fold down the rear seat locate the release lever (upper outboard side of seat), and lift it upward until the seatback releases. Slowly fold down the seatback. To raise the rear seat raise the seatback and lock it into place. If interference from the cargo area prevents the seatback from fully loc...

  • Page 167

    To open and close the hood release both the hood latches. Raise the hood and locate the safety latch, located in the middle of the hood opening. Push the safety latch to the left side of the vehicle, to open the hood. You may have to push down slightly on the hood before pushing the safety latch. In...

  • Page 168

    Lights multifunction lever the multifunction lever controls the operation of the parking lights, headlights, headlight beam selection, passing light, fog lights, instrument panel light dimming and turn signals. The multifunction lever is located on the left side of the steering column. Multifunction...

  • Page 169

    Headlights and parking lights turn the end of the multifunction lever to the first detent for parking light operation. Turn to the second detent for headlight operation. Automatic headlights — if equipped this system automatically turns the headlights on or off according to ambient light levels. To ...

  • Page 170

    Note: the engine must be running before the head- lights will turn on in the automatic mode. Turn signals move the multifunction lever up or down and the arrows on each side of the instrument cluster flash to show proper operation of the front and rear turn signal lights. Headlight switch turn signa...

  • Page 171

    Note: • if either light remains on and does not flash, or there is a very fast flash rate, check for a defective outside light bulb. If an indicator fails to light when the lever is moved, it would suggest that the indicator bulb is defective. • a tone will chime if the turn signals are left on for ...

  • Page 172

    Note: the fog lights will only operate with the parking lights or the headlights on low beam. Selecting high beam headlights will turn off the fog lights. Instrument panel dimmer rotate the center portion of the lever to the extreme bottom position to fully dim the instrument panel lights and preven...

  • Page 173

    Note: the daytime running light on the same side of the vehicle as the active turn signal will turn off auto- matically when a turn signal is in operation and turn on again when the turn signal is not operating. Interior lights the overhead light will turn on when a door is opened. It may also be tu...

  • Page 174

    Dimmer control in the multifunction lever. This light is also controlled automatically by the illuminated entry system. Cargo lamp the courtesy and dome lights will turn on when the front doors are opened, by rotating the control for the dimmer switch on the multifunction lever fully upward, or if e...

  • Page 175

    When a door is open and the interior lights are on, rotating the dimmer control to the extreme bottom posi- tion will cause all the interior lights to turn off. This is also known as the “party” mode because it allows the doors to stay open for extended periods of time without discharging the vehicl...

  • Page 176

    Windshield wiper operation rotate the end of the lever upward to the second detent past the intermittent settings for low-speed wiper opera- tion. Rotate the end of the lever upward to the third detent past the intermittent settings for high-speed wiper operation. Caution! In cold weather, always tu...

  • Page 177

    Caution! (continued) and the wipers freeze to the windshield, damage to the wiper motor may occur when the vehicle is restarted. Intermittent wiper system use the intermittent wiper when weather conditions make a single wiping cycle, with a variable pause be- tween cycles, desirable. Rotate the end ...

  • Page 178

    Windshield washers to use the washer, pull the lever toward you and hold while spray is desired. If the lever is pulled while in the delay range, the wiper will start and continue to operate for two or three wipe cycles after the lever is released, and then resume the intermittent interval previousl...

  • Page 179

    Tilt steering column this feature allows you to tilt the steering column upward or downward. The tilt lever is located on the steering column, below the turn signal lever. Push down on the lever to unlock the steering column. With one hand firmly on the steering wheel, move the steering column up or...

  • Page 180

    Warning! Do not adjust the steering column while driving. Adjusting the steering column while driving or driv- ing with the steering column unlocked, could cause the driver to lose control of the vehicle. Failure to follow this warning may result in serious injury or death. Electronic speed control ...

  • Page 181

    Note: in order to ensure proper operation, the elec- tronic speed control system has been designed to shut down if multiple speed control functions are operated at the same time. If this occurs, the electronic speed control system can be reactivated by pushing the electronic speed control on/off but...

  • Page 182

    To deactivate a soft tap on the brake pedal, pushing the cancel button, or normal brake pressure while slowing the vehicle will deactivate the electronic speed control with- out erasing the set speed memory. Pressing the on/off button or turning the ignition switch off erases the set speed memory. T...

  • Page 183

    To decrease speed when the electronic speed control is set, you can de- crease speed by pushing the set (-) button. The speed decrement shown is dependant on the speed of u.S. (mph) or metric (km/h) units: u.S. Speed (mph) • pressing the set (-) button once will result in a 1 mph decrease in set spe...

  • Page 184

    Warning! Electronic speed control can be dangerous where the system cannot maintain a constant speed. Your ve- hicle could go too fast for the conditions, and you could lose control and have an accident. Do not use electronic speed control in heavy traffic or on roads that are winding, icy, snow-cov...

  • Page 185

    A second power outlet is located inside the center console and is powered directly from the vehicle battery. Caution! • do not exceed the maximum power of 160 watts (13 amps) at 12 volts. If the 160 watt (13 amp) power rating is exceeded the fuse protecting the system will need to be replaced. • pow...

  • Page 186

    Warning! To avoid serious injury or death: • only devices designed for use in this type of outlet should be inserted into any 12 volt outlet. • do not touch with wet hands. • close the lid when not in use and while driving the vehicle. • if this outlet is mishandled, it may cause an electric shock a...

  • Page 187

    Caution! • many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.E., mobile phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting. • acce...

  • Page 188

    The power inverter is designed with built-in overload protection. If the power rating of 150 watts is exceeded, the power inverter will automatically shut down. Once the electrical device has been removed from the outlet the inverter should automatically reset. If the power rating exceeds approximat...

  • Page 189

    Warning! To avoid serious injury or death: • do not insert any objects into the receptacles. • do not touch with wet hands. • close the lid when not in use. • if this outlet is mishandled, it may cause an electric shock and failure. Cupholders front cupholders the front cupholders are located in the...

  • Page 190

    Storage glove compartment the lockable glove compartment is located on the pas- senger side of the lower instrument panel. Pull outward on the handle/latch to open the glove compartment. Console storage compartment to lock or unlock the storage compartment, insert the ignition key and turn. To open ...

  • Page 191

    There is an extra storage area underneath the console lid. The console lid has an integrated paper clip feature that can hold small items. Rear storage compartment the rear cargo area storage compartment cover is held by a spring-loaded latch. In order to remove the rear storage compartment cover, u...

  • Page 192

    Dual top — two-door models — if equipped if your vehicle is equipped with a dual top, you must remove one of the tops from the vehicle. If the soft top is removed, the pivot brackets must also be removed from the sport bar. The soft top was installed at the factory for shipping purposes only. The so...

  • Page 193

    2. Remove the hard top. Refer to “freedom top™ three- piece modular hard top — front/rear panel re- moval” in this section. 3. Remove the soft top bow assembly pivot bracket screws (two per side) using a #t30 torx® head driver. 4. Disconnect the knuckles from the left and right metal pivot brackets....

  • Page 194

    5. Unzip the zipper on the sport bar cover to expose the pivot brackets. Remove the brackets using a #t30 torx® head driver. Recover and re-zip the sports bar cover. Store the pivot brackets and screws in a safe place. 6. Reinstall the hard top. Refer to “freedom top™ three- piece modular hard top —...

  • Page 195

    B. Lay the soft top into the rear of the vehicle with the bows pointing forward and the curved portion of the bows facing upward. C. Reattach the knuckles onto the metal pivot brackets. Note: to aid in reattaching the knuckles, you may carefully tap on the knuckles using a rubber mallet. D. Screw th...

  • Page 196

    Caution! Do not overtighten the screws. You can strip the screws if they are overtightened. 5. Remove the swing gate bar (black metal bar for bottom of rear window) and set aside. Note: be sure the wire harness in the left rear corner is not tangled in the soft top bows before you lift the top. 6. U...

  • Page 197

    Mandatory to prevent any possible wear and tear on the soft top. Your vehicle warranty will not cover damage resulting from both tops remaining on the vehicle at the same time for extended periods of time. Removing the soft top — four-door models 1. Locate and remove the two boxes that contain the f...

  • Page 198

    4. Using the plastic reinforcement as a handle, slide the tether strap up the side bow (both sides). 5. The tether strap must be hooked onto the pivot bracket prior to removal of soft top from vehicle (both sides). 6. Remove the soft top bow assembly pivot bracket bolts (two per side) from the sport...

  • Page 199

    8. Remove the soft top from the vehicle and store in a clean, dry location (another person may be needed to help with this operation). Note: if you are doing this alone, use one arm to hold the bundle up, the other to remove the brackets. 9. Reinstall the hard top. Refer to “freedom top™ three- piec...

  • Page 200

    Installing the soft top — four-door models note: the following procedures are for first time set up only. For future soft top procedures, refer to “soft top” in this section. 1. Locate and remove the following items prior to hard top removal: • right and left door frames • six door frame attachment ...

  • Page 201

    5. Lower the pivot bracket onto the sport bar bracket mounting tab in a downward motion to lock into tab. 6. Install the pivot bracket bolts back into place using a 10.0 mm wrench or socket driver. Secure them until they are snug, being careful not to cross-thread the screws or overtighten. 3 unders...

  • Page 202

    Caution! Do not overtighten the screws. You can strip the screws if they are overtightened. 7. Remove the tether strap from the pivot bracket. 8. Using the plastic reinforcement as a handle remove the tether strap from the bracket hook by sliding strap up off hook and slide down the side bow (both s...

  • Page 203

    10. Remove the swing gate bar (black metal bar for bottom of rear window) and set aside. Note: be sure the wire harness in the left rear corner is not tangled in the soft top bows before you lift the top. 11. Unsnap and remove the black boot cover. This cover should be discarded. It was intended as ...

  • Page 204

    Freedom top™ three-piece modular hard top — if equipped caution! • the hard top is not designed to carry any addi- tional loads such as roof racks, spare tires, build- ing, hunting, or camping supplies, and/or luggage, etc. Also, it was not designed as a structural mem- ber of the vehicle, and thus ...

  • Page 205

    Front panel(s) removal note: left panel must be removed before removing right panel. 1. Fold down the sun visor, and move it to the side. 2. Turn the rear fasteners (knobs) (located on the over- head speaker bar assembly) counterclockwise until they can be removed. 3. Turn the center l-shaped locks ...

  • Page 206

    4. Turn the rear l-shaped lock (located above the shoul- der belt anchorage). 5. Unlatch the header panel latch located at the top of the windshield. 204 understanding the features of your vehicle.

  • Page 207

    6. Remove the left-hand panel. To remove the right panel, follow the steps above except for step 3. Freedom top™ storage bag vehicles equipped with a freedom top™ modular hard top, come with a freedom top™ storage bag that allows you to store your freedom top™ panels. The storage bag contains two co...

  • Page 208

    Note: ensure the front freedom top™ panel latch is closed prior to inserting the panel into the freedom bag. Insert the right side freedom panel into the bag with the latches facing downward. Unfold the black panel divider (ensure the divider is laying flat). Secure the velcro®, located at the cente...

  • Page 209

    Insert the left-side freedom panel into the bag with the latches facing upward. Note: ensure the front freedom panel latch is closed prior to inserting the panel into the bag. Unfold the outer flap and zip the freedom bag closed. 3 understanding the features of your vehicle 207.

  • Page 210

    Install the seat attachment strap (at the top of the bag) through the loops. Lift the freedom bag into the vehicle with the hooks and straps facing the back of the rear seat. Attach the clips at the bottom of the bag to the child restraint anchorages, located at the base of the rear seat. 208 unders...

  • Page 211

    Wrap the upper strap around the rear head restraints and loop the strap through the buckle. Pull on the strap to tighten the freedom bag securely against the rear seat. Front panel(s) installation note: set the panels on the windshield frame so that there is no overhang. Also, make sure that the pan...

  • Page 212

    Front panel(s) installation with rear hard top removed 1. Turn the left and right panels over and move the spacer block (located on the rear of the panel) upward 90 degrees. Note: the front panel(s) must be positioned properly to ensure sealing. Set the panels on the windshield frame so that there i...

  • Page 213

    4. Remove the six torx® head screws that secure the hard top to the vehicle (along the interior bodyside) using a #40 torx® head driver. 5. Open the swing gate all the way to ensure clearance of the rear window glass. Lift the rear window glass. 6. Locate the wire harness on the left rear inside cor...

  • Page 214

    7. Release the red locking tab by pulling outward to the right. 8. To remove the wiring harness press the tab and pull downward to disconnect. Red locking tab press tab to disconnect 212 understanding the features of your vehicle.

  • Page 215

    9. To remove the washer hose, pinch the grips on hose connector and pull downward. 10. Close the swing gate. 11. Remove the hard top from the vehicle. Place the hard top on a soft surface to prevent damage. Caution! The removal of the freedom top™ requires four adults located on each corner. Failure...

  • Page 216

    Note: • the torx® fasteners that attach the hard top to the body should be torqued to 88 in lb +/- 22 in lb (10 n·m +/- 2.5 n·m). • it is not necessary to pinch connection when rein- stalling washer hose. Push on until click is heard. Door frame caution! Failure to follow these cautions may cause in...

  • Page 217

    Door frame removal 1. Unscrew and remove the door frame attachment knobs (two per door). Warning! Use both hands to remove the door frames. The door frames will fold and could cause injury if both hands are not used. 2. Place one hand on the upper rear and one hand on the front of the door frame. 3 ...

  • Page 218

    3. Pull the frame toward you with your rearward hand to remove the frame from the vehicle. 4. Screw the knobs back into the door frame and fold for storage. Store in a secure location. Warning! • do not drive your vehicle on public roads with the door frame(s) removed as you will lose the protec- ti...

  • Page 219

    Warning! (continued) • do not drive your vehicle on public roads with the doors removed as you will lose the protection that they can provide. This procedure is furnished for use during off-road operation only. Door frame installation — two-door models — if equipped 1. Unfold door frame and unscrew ...

  • Page 220

    4. Starting with the front of the door frame, clip it over the metal side bar and then clip the rear, making sure that the material for the side bar covers is not pinched by the door frame. 5. Starting with the front knob, screw in and tighten both knobs. Repeat on the other side. 218 understanding ...

  • Page 221

    Door frame installation — four-door models — if equipped 1. Install the rear door frame first. 2. Set the door frame pin into the hole on top of the body side, just behind the rear door opening. 3. Position the top of the door frame against the metal sport bar and press onto the side bar making sure...

  • Page 222

    4. Loosely install the rear knob (long knob) to hold the door rail in position. 5. Carefully set the front of the front door frame in the rubber seal at the top of the windshield. 6. Clip the front of the door rail over the side bar making sure that the material for the side bar cover is not pinched...

  • Page 223

    8. Loosely install both knobs beginning with the front knob (long knob). Then, install the middle knob (short knob) through the front and rear door frames and screw into the top of the b-pillar. 9. Tighten the front knob, then the rear most knob, and then the middle knob. Repeat this procedure for t...

  • Page 224

    If the temperature is below 72°f (24°c) and/or the top has been folded down for a period of time, the top will appear to have shrunk when you raise it, making it difficult to put up. This is caused by a natural contraction of the vinyl coating on the fabric top. Place the vehicle in a warm area. Pul...

  • Page 225

    Warning! • do not drive the vehicle with the rear window curtain up unless the side curtains are also re- moved. Dangerous exhaust gases could enter the vehicle causing harm to the driver and passengers. • the fabric upper doors and fabric top are designed only for protection against the elements. D...

  • Page 226

    Quick steps to lowering the soft top refer to “lowering the soft top” in this section for further information. 1. Remove the side windows. 2. Remove the back window. 224 understanding the features of your vehicle.

  • Page 227

    3. Release header latches from the windshield frame. 4. Release the sail panel retainers from the body side channel at the rear corners of the vehicle. Note: when releasing the sail panel retainers, it is helpful to pull down on the rear roof bow. 3 understanding the features of your vehicle 225.

  • Page 228

    5. As you begin to lower the top, fold the sail panels so that they rest on top of the soft top. 6. Release the sunrider® latch (both sides). 226 understanding the features of your vehicle.

  • Page 229

    7. Open the swing gate and lower the top. Note: ensure fabric does not overhang the sides of the vehicle. Quick steps to raising the soft top refer to “raising the soft top” in this section for further information. 1. Open the swing gate and raise the top, engaging the sunrider® latches (another per...

  • Page 230

    2. Engage header latches. 3. Install rear corner panels. 228 understanding the features of your vehicle.

  • Page 231

    4. Install the back window. 5. Install the side windows. 3 understanding the features of your vehicle 229.

  • Page 232

    6. To install the side windows, affix the window tempo- rarily by attaching to the velcro® in the rear corner. Start the zipper but close only about 1 in (2.5 cm). 7. Insert the front retainer of the window into the door channel, making sure the retainer is fully seated and properly positioned on th...

  • Page 233

    8. Insert the retainer along the bottom edge of the window into the bottom side channel, beginning at the front and working to the rear of the vehicle. Finish by closing the zipper completely and attaching the vel- cro® along the top and rear of the window. Repeat this step for the opposite side. 1 ...

  • Page 234

    Lowering the soft top 1 — header bow 6 — quarter window 2 — 2–bow 7 — check strap 3 — 3–bow 8 — front retainer — quarter window 4 — sail panel 9 — bottom retainer — quarter window 5 — body side retainer 232 understanding the features of your vehicle.

  • Page 235

    1 — zipper start 2 — zipper finish 3 — swing gate bar 4 — swing gate brackets 5 — sail panels 3 understanding the features of your vehicle 233.

  • Page 236

    Note: clean side and rear windows before removal to assist in preventing scratching during removal of the soft top. If zippers are difficult to operate due to road dust, etc., clean them with a mild soap solution and a small brush. Cleaning products are available through your authorized dealer. 1. I...

  • Page 237

    4. Open the swing gate. 5. Before unzipping the rear window, release the first 3 in (7.6 cm) of both sail panels from the channel. Remove the swing gate bar by pulling it straight rearward out of the swing gate brackets. • unzip the rear window starting at the right lower corner of the window. Pull ...

  • Page 238

    6. Remove the rear window retainer from the swing gate bracket on both the left and right sides. 7. Stow the windows carefully to avoid scratching. 8. Undo the velcro® that runs along the top and rear edge of the side window. 9. Beginning from the rear lower corner, completely unzip the window. 10. ...

  • Page 239

    11. Finish releasing the sail panel retainers from the body side channel at the rear corners of the vehicle. Note: when releasing the sail panel retainers, it is helpful to pull down on the rear roof bow. 12. As you begin to lower the top, fold the sail panels so that they rest on top of the soft to...

  • Page 240

    13. The swing gate brackets do not need to be removed unless the hard top is being installed. To remove the swing gate brackets, pull the front of the bracket forward while rolling the entire bracket back in toward the vehicle to disengage. 14. Completely release the latches from the loops on the wi...

  • Page 241

    15. Make sure the plastic sleeves are slid rearward over the sunrider® link (sunrider® models only). 16. Unlatch the side bows from both door rails (sun- rider® models only). 3 understanding the features of your vehicle 239.

  • Page 242

    17. Before lowering the top, open the swing gate to prevent possible damage to the rear center high- mounted brake light. Move to the front of the vehicle. Grasp the side bow behind the header and lift the top, folding it toward the rear of the vehicle. Note: help from another person will ease this ...

  • Page 243

    Raising the soft top 1. Unclip and move the sun visors to the side. 2. Install door frames, if removed. Refer to “door frame” in this section for further information. 3. Make sure the plastic sleeve is slid over sunrider® link (sunrider® models only). 4. Standing on the side of the vehicle, lift the...

  • Page 244

    5. Make sure the sunrider® bracket on the side bows latches to the door rails (sunrider® models only). 6. Open the header latches and engage the hook on each side onto the windshield loops (do not close the latches). 242 understanding the features of your vehicle.

  • Page 245

    7. If the swing gate brackets were removed, install them by hooking the rear edge of the bracket on the interior side of the body channel. Then, rotate it rearward and over the channel until it snaps onto the exterior part of the rail. To be properly located, the bracket must only be clipped to the ...

  • Page 246

    9. Partially install the sail panel retainers into the body side channel, leaving the last 3 in (7.6 cm) toward the rear window loose (on both sides). Pulling down on the rear roof bow (3–bow) will aid to reach the channel with the retainers. 10. To install the side windows, affix the window tempo- ...

  • Page 247

    11. Insert the front retainer of the window into the door channel, making sure the retainer is fully seated and properly positioned on the door frame. Failure to do so can result in wind and water leaks or damage to the window. 1 — incorrect insertion 2 — correct insertion 3 understanding the featur...

  • Page 248

    12. Insert the retainer along the bottom edge of the window into the bottom side channel, beginning at the front and working to the rear of the vehicle. Finish by closing the zipper completely and attaching the velcro® along the top and rear of the window. Repeat this step for the opposite side. 246...

  • Page 249

    13. Locate the black swing gate bar. Slide the swing gate bar over the receiver at the bottom inside of the rear window. The spongy part of the seal should be down and pointed outward to seal with the swing gate when closed. 14. Install the rear window by starting both zipper ends at the lower left ...

  • Page 250

    15. Run the zipper fully around to the right side of the window. 16. Grasp the swing gate bar and position it into the swing gate brackets. 248 understanding the features of your vehicle.

  • Page 251

    17. Insert the rear window retainer into the swing gate bracket on both the left and right sides. 18. Apply downward pressure on the top corner of the rear soft top bow (3–bow), then complete attaching the sail panel retainers into the body side channel. 19. Close the header latches and return the s...

  • Page 252

    Soft top — four-door models please visit the owner’s section of jeep.Com for instruc- tional videos. Caution! The soft top is not designed to carry any additional loads such as roof racks, spare tires, building, hunt- ing, or camping supplies, and/or luggage, etc. Also, it was not designed as a stru...

  • Page 253

    Caution! (continued) • do not lower the top with the windows installed. Window and top damage may occur. • refer to “appearance care for fabric top models” in “maintaining your vehicle” for further informa- tion. It contains important information on cleaning and caring for your vehicle’s fabric top....

  • Page 254

    Caution! Failure to follow these cautions may cause interior water damage, stains or mildew on the top material: • it is recommended that the top be free of water prior to opening it. Operating the top, opening a door or lowering a window while the top is wet may allow water to drip into the vehicle...

  • Page 255

    Quick steps for lowering the soft top 1. Remove the side windows. 2. Remove the back window. Note: start zipper from the right side to remove back window. 3 understanding the features of your vehicle 253.

  • Page 256

    3. Release header latches from the windshield frame. 4. Release the sail panel retainers from the body side channel at the rear corners of the vehicle. Note: when releasing the sail panel retainers, it is helpful to pull down on the rear roof bow. 254 understanding the features of your vehicle.

  • Page 257

    5. Fold the sail panels so that they rest on top of the soft top. 6. Fold header rearward, pulling the fabric to the rear. 3 understanding the features of your vehicle 255.

  • Page 258

    7. Release sunrider® latch (both sides). 256 understanding the features of your vehicle.

  • Page 259

    8. Open the swing gate and lower the top. Note: ensure the fabric does not overhang the sides of the vehicle. Quick steps for raising the soft top 1. Open the swing gate and raise the top, engaging the sunrider® latches (another person may be needed to help with this operation). 3 understanding the ...

  • Page 260

    2. Install rear corner panels. 258 understanding the features of your vehicle.

  • Page 261

    3. Rotate the header forward. 4. Engage the header latches. 3 understanding the features of your vehicle 259.

  • Page 262

    5. Install the back window. 6. Install the side windows. 260 understanding the features of your vehicle.

  • Page 263

    7. To install the side windows, affix the window tempo- rarily by attaching to the velcro® in the rear corner. Start the zipper but close only about 1 in (2.5 cm). 8. Insert the front retainer of the window into the door channel, making sure the retainer is fully seated and properly positioned on th...

  • Page 264

    9. Insert the retainer along the bottom edge of the window into the bottom side channel, beginning at the front and working to the rear of the vehicle. Finish by closing the zipper completely and attaching the vel- cro® along the top and rear of the window. Repeat this step for the opposite side. 26...

  • Page 265

    Folding down the soft top 1 — header bow 6 — body side retainer 2 — 2–bow 7 — quarter window 3 — 3–bow 8 — check strap 4 — 4–bow 9 — front retainer — quarter window 5 — sail panel 10 — bottom retainer — quarter window 3 understanding the features of your vehicle 263.

  • Page 266

    1 — zipper start 2 — zipper finish 3 — swing gate bar 4 — swing gate brackets 5 — sail panels 264 understanding the features of your vehicle.

  • Page 267

    Note: clean side and rear windows before removal to assist in preventing scratching during removal of the soft top. If zippers are difficult to operate due to road dust, etc., clean them with a mild soap solution and a small brush. Cleaning products are available through your authorized dealer. 1. I...

  • Page 268

    4. Open the swing gate. 5. Before unzipping the rear window, release the first 3 in (7.6 cm) of both sail panels from the channel. Remove the swing gate bar by pulling it straight rearward out of the swing gate brackets. • unzip the rear window starting at the right lower corner of the window. Pull ...

  • Page 269

    7. Stow the windows carefully to avoid scratching. 8. Undo the velcro® that runs along the top and rear edge of the side window. 9. Beginning from the rear lower corner, completely unzip the window. 10. Once unzipped, remove the side window retainers from the door channel and body side channel. Repe...

  • Page 270

    Note: when releasing the sail panel retainers, it is helpful to pull down on the rear roof bow. 12. Fold the sail panels so that they rest on top of the soft top. 268 understanding the features of your vehicle.

  • Page 271

    13. The swing gate brackets do not need to be removed unless the hard top is being installed. To remove the swing gate brackets, pull the front of the bracket forward while rolling the entire bracket back in toward the vehicle to disengage. 14. Grasp the front side bow behind the header, and lift th...

  • Page 272

    15. Fold back the front section of the top, pulling the fabric rearward. Gently rest the header on top of the rear portion of the deck. 16. Fold the top so that the material forms a ⬙ w ⬙ as shown. Enter the vehicle and move the material into two folds. 270 understanding the features of your vehicle.

  • Page 273

    17. Release the side bows by pressing down on the latch above the front of the rear door. Push the top rearward to disengage. Repeat this step on the other side. 18. Before lowering the top, open the swing gate to prevent possible damage to the rear center high- mounted brake light. Grasp the folded...

  • Page 274

    20. Tuck the fabric and the check straps between the bows as far inside as possible. This will keep any portion of the top from flapping outside of the vehicle. 21. Once the top is fully down, use the velcro® straps provided to secure the top to the vehicle by wrapping the strap around the side bows...

  • Page 275

    Putting up the soft top note: be extremely careful when putting up the soft top to prevent the doors from getting scratched. It may be helpful to open the rear doors. 1. Install the door frames, if removed. Refer to “door frame” in this section for further information. 2. Undo the straps used to sec...

  • Page 276

    5. Insert the slider feature of the knuckles into the door frame tracks and slide the top forward. 6. Ensure that the top locks into the sunrider® locking mechanisms that are located above the front of the rear doors. 274 understanding the features of your vehicle.

  • Page 277

    7. Unclip and move the sun visors to the side. 8. Standing on the side of the vehicle, lift the top by the side bow until it rests on the windshield frame. 9. Open the header latches and engage the hook on each side onto the windshield loops (do not close the latches). 3 understanding the features o...

  • Page 278

    10. If the swing gate brackets were removed, install them by hooking the rear edge of the bracket on the interior side of the body channel. Then, rotate it rearward and over the channel until it snaps onto the exterior part of the rail. To be properly located, the bracket must only be clipped to the...

  • Page 279

    Partially install the sail panel retainers into the body side channel, leaving the last 3 in (7.6 cm) toward the rear window loose (on both sides). Pulling down on the rear roof bow (4–bow) will aid in reaching the channel with the retainers. 12. To install the side windows, affix the window tem- po...

  • Page 280

    13. Insert the front retainer of the window into the door channel, making sure the retainer is fully seated and properly positioned on the door frame. Failure to do so can result in wind and water leaks or damage to the window. 1 — incorrect insertion 2 — correct insertion 278 understanding the feat...

  • Page 281

    14. Insert the retainer along the bottom edge of the window into the bottom side channel, beginning at the front and working to the rear of the vehicle. Finish by closing the zipper completely and attaching the velcro® along the top and rear of the window. Repeat this step for the opposite side. 3 u...

  • Page 282

    15. Locate the black swing gate bar. Slide the swing gate bar over the receiver at the bottom inside of the rear window. The spongy part of the seal should be down and pointed outward to seal with the swing gate when closed. 16. Install the rear window by starting both zipper ends at the lower left ...

  • Page 283

    17. Run the first zipper fully around to the right side of the window. 18. Grasp the swing gate bar and position it into the swing gate brackets. 19. Insert the rear window retainer into the swing gate bracket on both the left and right sides. 3 understanding the features of your vehicle 281.

  • Page 284

    20. Complete the installation of the sail panel by insert- ing the rest of the retainer into the body channel. 21. Close the header latches and return the sun visors to their secured position. Sunrider® (two-door models) caution! Operating the top, opening a door or lowering a window while the top i...

  • Page 285

    Opening the sunrider® 1. Unclip and move the sun visors to the side. 2. Release the header latches from the loops on the windshield frame. 3. Slide the plastic sleeve forward. 3 understanding the features of your vehicle 283.

  • Page 286

    4. Grasp the header and lift the top back. Make sure the material is folded back as shown. Note: the sunrider® latch on the door rail should not be activated for sunrider® use. If activated, the soft top must be reinstalled starting from the sail panels. 5. Locate the straps to secure the side bows....

  • Page 287

    Closing the sunrider® 1. Remove the straps from the side bows. 2. Unclip and move the sun visors to the side. 3. Grasp the front header and pull it to the front of the vehicle. 4. Hook the header latches to the loops on the wind- shield frame, close latches, and return the sun visors to their origin...

  • Page 288

    Opening the sunrider® 1. Unclip and move the sun visors to the side. 2. Release the header latches from the loops on the windshield frame. 3. Grasp the front side bow behind the header, and lift the top. 286 understanding the features of your vehicle.

  • Page 289

    4. Fold back the front section of the top and gently rest the header on top of the rear portion of the deck. 5. Fold the top so that the material forms a ⬙ w ⬙ as shown. Enter the vehicle and move the material into two folds. 3 understanding the features of your vehicle 287.

  • Page 290

    6. Secure the top by using the two provided straps. Each strap will wrap around the side bow and velcro® to itself; use one strap on each side of the vehicle. Closing the sunrider® perform the above steps in the opposite order. Note: failure to fold the fabric rearward will allow the material to sag...

  • Page 291

    Remove the side bars and fold down the windshield, drive slowly and cautiously. It is recommended that the speed of the vehicle be limited to 10 mph (16 km/h), with low range operation preferred if you are driving off-road with the windshield folded down. Raise the windshield and reinstall the side ...

  • Page 292

    Warning! (continued) • if you remove the doors, store them outside the vehicle. In the event of an accident, a loose door may cause personal injury. Lowering the windshield and removing side bars 1. Lower the fabric top or remove the hard top following the instructions in this manual. Note: to assis...

  • Page 293

    7. Remove the one hex bolt (13 mm) visible through the plastic trim on the bottom side of the side bar, one hex bolt (13 mm) on the side of the side bar, and one hex bolt (13 mm) on top of the side bar. Note: pull side bar out horizontally when removing. Caution! Do not remove the head impact foam f...

  • Page 294

    Warning! You or others could be injured if you carry the side bars loose in your vehicle. Remove the side bars from the vehicle or securely store them as described or they may cause personal injury if an accident occurs. See your authorized dealer for the cinch straps. 10. Remove the windshield wipe...

  • Page 295

    13. Secure the windshield by passing a cinch strap through the footman hoop on the center of the hood and on the center of the windshield frame. Tighten the strap to secure the windshield in place. Raising the windshield and replacing side bars 1. Raise the windshield. 2. Loosely attach the rear of ...

  • Page 296

    3. Attach the front of the side bar to the windshield frame. • install the top two hex bolts (13 mm) first, then the lower side hex bolt (13 mm). The lower side bolt will not align until the top two bolts are installed. 4. Tighten all side bar attachment bolts. 5. Install the lower windshield plates...

  • Page 297

    Rear window features — hard top only rear window wiper/washer — if equipped a rotary switch on the center portion of the control lever (located on the right side of the steering column) controls the operation of the rear wiper/washer function. Rotate the switch upward to the first detent position fo...

  • Page 298

    Rear window defroster — if equipped the rear window defroster button is located on the bottom right-side of the blower control knob. Press this button to turn on the rear window defroster. An indicator in the button will illuminate when the rear window defroster is on. The rear window defroster auto...

  • Page 299: Contents

    Understanding your instrument panel contents 䡵 instrument panel features . . . . . . . . . .300 䡵 instrument cluster . . . . . . . . . . . . . . . . .301 䡵 instrument cluster descriptions . . . . .302 䡵 compass and trip computer — if equipped . . . . . . . . . . . . . . . . . . . . . . . . .317 ▫ co...

  • Page 300

    ▫ advanced evic messages (customer information features). . . . . . . . . . . . . . . . . . . . . . . . . . . .332 ▫ system status . . . . . . . . . . . . . . . . . . . . . . . .332 ▫ personal settings (customer-programmable features) . . . . . . . . . . . . . . . . . . . . . . . . . . .333 䡵 uconne...

  • Page 301

    䡵 uconnect® 130 with satellite radio . . . . .366 ▫ operating instructions — radio mode . . . . . .366 ▫ operation instructions — cd mode for cd and mp3 audio play . . . . . . . . . . . . . . . . . . . . . .372 ▫ notes on playing mp3 files . . . . . . . . . . . . .375 ▫ list button — cd mode for mp3...

  • Page 302

    Instrument panel features 1 — air outlet 7 — climate controls 2 — instrument cluster 8 — power outlet 3 — radio 9 — lower switch bank 4 — assist handle 10 — power mirror switch — if equipped 5 — glove compartment 11 — horn 6 — power window switches 300 understanding your instrument panel.

  • Page 303

    Instrument cluster 4 understanding your instrument panel 301.

  • Page 304

    Instrument cluster descriptions 1. Fuel gauge the pointer shows the level of fuel in the fuel tank when the ignition switch is in the on/run position. 2. Charging system light this light shows the status of the electrical charg- ing system. The light should come on when the ignition switch is first ...

  • Page 305

    7. Seat belt reminder light when the ignition switch is first turned to on/ run, this light will turn on for four to eight seconds as a bulb check. During the bulb check, if the driver’s seat belt is unbuckled, a chime will sound. After the bulb check or when driving, if the driver seat belt remains...

  • Page 306

    Pull the lever toward you to switch the headlights back to low beam. If the driver’s door is open, and the headlights or park lights are left on, the high beam indicator light will remain illuminated and a chime will sound. 11. Brake warning light this light monitors various brake functions, includi...

  • Page 307

    Warning! Driving a vehicle with the red brake light on is dangerous. Part of the brake system may have failed. It will take longer to stop the vehicle. You could have a collision. Have the vehicle checked immediately. Vehicles equipped with the anti-lock brake system (abs), are also equipped with el...

  • Page 308

    13. Air bag warning light this light will turn on for four to eight seconds as a bulb check when the ignition switch is first turned to on/run. If the light is either not on during starting, stays on, or turns on while driving, have the system inspected at an authorized dealer as soon as possible. R...

  • Page 309

    17. Vehicle security light — if equipped this light will flash at a fast rate for approxi- mately 15 seconds, when the vehicle security alarm is arming, and then will flash slowly until the vehicle is disarmed. 18. Temperature gauge the temperature gauge shows engine coolant tempera- ture. Any readi...

  • Page 310

    Warning! (continued) vehicle”. Follow the warnings under the cooling system pressure cap paragraph. 19. Cruise indicator this indicator shows when the electronic speed control system is turned on. 20. 4wd indicator light — if equipped this light alerts the driver that the vehicle is in the four-whee...

  • Page 311

    As an added safety feature, your vehicle has been equipped with a tire pressure monitoring system (tpms) that illuminates a low tire pressure telltale when one or more of your tires is significantly under-inflated. Accordingly, when the low tire pressure telltale illumi- nates, you should stop and c...

  • Page 312

    Caution! The tpms has been optimized for the original equipment tires and wheels. Tpms pressures and warning have been established for the tire size equipped on your vehicle. Undesirable system opera- tion or sensor damage may result when using re- placement equipment that is not of the same size, t...

  • Page 313

    Vehicle odometer messages when the appropriate conditions exist, the following odometer messages will display: eco . . . . . . . . . . . . . . . . . . . . . Fuel saver indicator door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Door ajar gate . . . . . . . . . . . . . . . . . . . . . . ...

  • Page 314

    (e.G., snow plowing, off-road operation). If this “hot- oil” message turns on, stop the vehicle and run the engine at idle or faster with the transmission in neu- tral until the message turns off. Caution! Continuous driving with the transmission tempera- ture “hotoil” warning message illuminated wi...

  • Page 315

    Change oil message your vehicle is equipped with an engine oil change indicator system. The “change oil” message will flash in the instrument cluster odometer for approximately 12 seconds after a single chime has sounded to indicate the next scheduled oil change interval. The engine oil change indic...

  • Page 316

    Stays on through several typical driving styles. In most situations, the vehicle will drive normally and will not require towing. When the engine is running, the mil may flash to alert serious conditions that could lead to immediate loss of power or severe catalytic converter damage. The vehicle sho...

  • Page 317

    System. If this light remains on after several ignition cycles, and the vehicle has been driven several miles (kilometers) at speeds greater than 30 mph (48 km/h), see your authorized dealer as soon as possible to have the problem diagnosed and corrected. Note: • the “esc off indicator light” and th...

  • Page 318

    28. Electronic stability control (esc) off indicator light — if equipped this light indicates the electronic stability con- trol (esc) is off. 29. Electronic throttle control (etc) light this light informs you of a problem with the electronic throttle control (etc) system. If a problem is detected w...

  • Page 319

    Compass and trip computer — if equipped the compass/trip computer features a driver- interactive display (displays information on outside tem- perature, compass direction, and trip information). It is located on the lower left part of the cluster below the speedometer. Control buttons the compass/te...

  • Page 320

    Press and release the step button on the steering wheel to access the options in the compass display. Note: the system will display the last known outside temperature when starting the vehicle and may need to be driven several minutes before the updated tempera- ture is displayed. Engine temperature...

  • Page 321

    Compass/temperature display note: if the vehicle is equipped with a chrysler uconnect® gps (navigation radio), the nav system will provide the compass direction, and the variance and calibration menus will be unavailable. The compass will perform accurately, based on gps signals instead of the earth...

  • Page 322

    Button to increase the variance one step. Repeat as necessary until the desired variance is achieved. Note: the factory default zone is 8. During program- ming, the zone value will wrap around from zone 15 to zone 1. Manual compass calibration if the compass appears erratic, inaccurate or abnormal, ...

  • Page 323

    Average fuel economy / distance to empty (dte) / elapsed time • average fuel economy shows the average fuel economy since the last reset. When the fuel economy is reset, the digits will go blank while the history information is erased. The averaging will restart when enough new distance and fuel dat...

  • Page 324

    Trip a shows the total distance traveled for trip a since the last reset. Trip b shows the total distance traveled for trip b since the last reset. Eco (fuel saver indicator) — if equipped the eco indicator will illuminate when you are driving in a fuel efficient manner and can be used to modify dri...

  • Page 325

    This system conveniently allows the driver to select a variety of useful information by pressing the switches mounted on the steering wheel. The evic consists of the following: • compass heading (n, s, e, w, ne, nw, se, sw) • outside temperature (°f or °c) • digital speedometer • vehicle info • eco ...

  • Page 326

    The system allows the driver to select information by pressing the following buttons mounted on the steering wheel: • menu button press and release the menu button to advance the display to each of the evic main menu features or to return to the main menu from a sub-menu. Upon reaching the last item...

  • Page 327

    • select button press and release the select button when prompted by the evic to reset main menu features with a reset capability or to change personal settings. • down button press and release the down button when prompted by the evic to step through stored system warning messages or personal setti...

  • Page 328

    • personal settings not avail. – vehicle in motion — manual transmission • door ajar (with vehicle graphic showing which door is open. A single chime sounds if the vehicle is in motion). • gate ajar (with vehicle graphic showing the liftgate/ back door open and a single chime ) • check gascap (refer...

  • Page 329

    Note: if the indicator message illuminates when you start the vehicle, the oil change indicator system did not reset. If necessary, repeat this procedure. Evic main menu to step to each main menu feature press and release the menu button once for each step. A step from the last item in the list will...

  • Page 330

    Select button graphic. Pressing select a second time will reset both average fuel economy and elapsed time. After three seconds without pressing select, reset all will return to reset and only the selected feature will have been reset. Compass display / eco (fuel saver mode) — if equipped the compas...

  • Page 331

    Metallic objects) until the “cal” message displayed in the evic turns off. The compass will now function normally. Note: a good calibration requires a level surface and an environment free from large metallic objects such as buildings, bridges, underground cables, railroad tracks, etc. Manual compas...

  • Page 332

    Note: magnetic materials should be kept away from the top of the instrument panel; this is where the compass sensor is located. To change the compass variance: 1. Turn the ignition switch run (it is not necessary to start the engine). 2. Press the menu button until personal settings (customer-progra...

  • Page 333

    Display). Upon reset, the history information will be erased, and the averaging will continue from the last fuel average reading before the reset. Distance to empty (dte) shows the estimated distance that can be traveled with the fuel remaining in the tank. This estimated distance is determined by a...

  • Page 334

    Evic units selection (units in display) displays the units used for the outside temperature, average fuel economy and distance to empty features. Press and release the select button to toggle units between ⬙ u.S. ⬙ and ⬙ metric ⬙ . Advanced evic messages (customer information features) press and rel...

  • Page 335

    Personal settings (customer-programmable features) personal settings allows the driver to set and recall features when the vehicle speed is at 0 mph (0 km/h) (manual transmission) or when the shift lever is in park (auto transmission). Press and release the menu button until personal set- tings disp...

  • Page 336

    Rke unlock when driver door 1st press is selected, only the driver’s door will unlock on the first press of the remote keyless entry (rke) transmitter unlock button. When driver door 1st press is selected, you must press the rke transmitter unlock button twice to unlock the passen- ger’s doors. When...

  • Page 337

    Headlamps with wipers (available with auto headlights only) when on is selected, and the headlight switch is in the auto position, the headlights will turn on approxi- mately 10 seconds after the wipers are turned on. If the headlights were turned on by this feature they will also turn off when the ...

  • Page 338

    Display units in the evic can be changed between english and metric units of measure. The units apply to the outside tem- perature, average fuel economy, and distance to empty. To make your selection, press and release the select button until “u.S.” or ⬙ metric ⬙ appears. Nav–turn by turn — if equip...

  • Page 339

    Uconnect® 230 – am/fm stereo radio and 6–disc cd/dvd changer (mp3/wma aux jack) operating instructions — radio mode note: the ignition switch must be in the on or acc position to operate the radio. Power switch/volume control (rotary) push the on/volume control knob to turn on the radio. Press the o...

  • Page 340

    Seek buttons press and release the seek buttons to search for the next listenable station in am/fm mode. Press the right switch to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection. Holding either button will bypass stations wit...

  • Page 341

    Time button press the time button to alternate locations of the time and frequency display. Clock setting procedure 1. Press and hold the time button until the hours blink. 2. Adjust the hours by turning the right side tune/ scroll control knob. 3. After adjusting the hours, press the right side tun...

  • Page 342

    Setting the tone, balance and fade push the rotary tune/scroll control knob and bass will display. Turn the tune/scroll control knob to the right or left to increase or decrease the bass tones. Push the rotary tune/scroll control knob a second time and mid will display. Turn the tune/scroll control ...

  • Page 343

    Music type button pressing this button once will turn on the music type mode for five seconds. Pressing the music type button or turning the tune/scroll control knob within five seconds will allow the program format type to be se- lected. Many radio stations do not currently broadcast music type inf...

  • Page 344

    Program type 16-digit character dis- play soft soft soft rock soft rck soft rhythm and blues soft r & b sports sports talk talk top 40 top 40 weather weather by pressing the seek button when the music type icon is displayed, the radio will be tuned to the next frequency station with the same selecte...

  • Page 345

    • subtitle — repeatedly pressing select will switch subtitles to different subtitle languages that are avail- able on the disc (if equipped). • audio stream — repeatedly pressing select will switch to different audio languages (if supported on the disc) (if equipped). • angle — repeatedly pressing s...

  • Page 346

    Enter the four-digit country code using the tune/ scroll control knob to scroll up and down to select the number and then push to select. Audio language — if equipped selecting this item allows you to choose a default audio language (effective only if the language is supported by the disc). You can ...

  • Page 347

    Auto-play the main title. In such cases, use the menu button on the remote control to select desired title to play. Note: the user will have to set these defaults before loading a disc. If changes are made to these settings after a disc is loaded, changes will not be effective. Also, the defaults ar...

  • Page 348

    Buttons 1 - 6 these buttons tune the radio to the stations that you commit to pushbutton memory {12 am, 12 fm, and 12 satellite (if equipped) stations}. Disc button pressing the disc button will allow you to switch from am/fm modes to disc modes. Operation instructions — disc mode for cd and mp3/wma...

  • Page 349

    Radio display will show ⬙ loading disc ⬙ when the disc is loading and “reading disc” when the radio is reading the disc. Caution! This cd player will accept 4–3/4 in (12 cm) discs only. The use of other sized discs may damage the cd player mechanism. Eject button — ejecting compact disc(s) press the...

  • Page 350

    Time button (cd mode) press this button to change the display from a large cd playing time display to a small cd playing time display. Rw/ff (cd mode) press and hold ff (fast forward) and the cd player will begin to fast forward until ff is released, or rw or another cd button is pressed. The rw (re...

  • Page 351

    • maximum number of folders: 100 • maximum number of characters in file/folder names: • level 1: 12 (including a separator ⬙ . ⬙ and a three- character extension) • level 2: 31 (including a separator ⬙ . ⬙ and a three- character extension) multisession disc formats are supported by the radio. Multis...

  • Page 352

    Mpeg specifi- cation sampling fre- quency (khz) bit rate (kbps) mpeg-1 audio layer 3 48, 44.1, 32 320, 256, 224, 192, 160, 128, 112, 96, 80, 64, 56, 48 mpeg-2 audio layer 3 24, 22.05, 16 160, 128, 144, 112, 96, 80, 64, 56, 48 wma specifi- cation sampling fre- quency (khz) bit rate (kbps) wma 44.1 an...

  • Page 353

    To increase the speed of disc loading, it is recommended to use cd-r media and single-session discs. To create a single-session disc, enable the “disc at once” option before writing to the disc. List button — disc mode for mp3/wma play pressing the list button will bring up a list of all folders on ...

  • Page 354

    Note: the aux device must be turned on and the device’s volume set to the proper level. If the aux audio is not loud enough, turn the device’s volume up. If the aux audio sounds distorted, turn the device’s volume down. Seek button (auxiliary mode) no function. Scan button (auxiliary mode) no functi...

  • Page 355

    Dolby® manufactured under license from dolby® laboratories. Dolby® and the double-d symbol are trademarks of dolby® laboratories. Macrovision this product incorporates copyright protection technol- ogy that is protected by u.S. Patents and other intellec- tual property rights. Use of this copyright ...

  • Page 356

    Visit the sirius web site at www.Sirius.Com, or at www.Siriuscanada.Ca for canadian residents. Electronic serial number/sirius identification number (esn/sid) please have the following information available when calling: 1. The electronic serial number/sirius identification number (esn/sid). 2. Your...

  • Page 357

    Reception quality satellite reception may be interrupted due to one of the following reasons: • the vehicle is parked in an underground parking structure or under a physical obstacle. • dense tree coverage may interrupt reception in the form of short audio mutes. • driving under wide bridges or alon...

  • Page 358

    Additional three seconds will make the radio display the song title all of the time (press and hold again to return to normal display). Rw/ff pressing the rw (rewind) or ff (fast forward) buttons causes the tuner to search for the next channel in the direction of the arrows. Tune control (rotary) tu...

  • Page 359

    Set button — to set the pushbutton memory when you are receiving a channel that you wish to commit to pushbutton memory, press the set button. The symbol set 1 will now show in the display window. Select the button (1-6) you wish to lock onto this channel and press and release that button. If a butt...

  • Page 360

    Uconnect® 130 operating instructions — radio mode note: the ignition switch must be in the on/run or acc position to operate the radio. Power switch/volume control (rotary) push the on/volume control knob to turn on the radio. Push the on/volume control knob a second time to turn off the radio. Elec...

  • Page 361

    Another selection. Holding either button will bypass stations without stopping, until you release it. Time button press the time button to alternate display of the time and radio frequency. Clock setting procedure 1. Press and hold the time button until the hours blink. 2. Adjust the hours by turnin...

  • Page 362

    Push the rotary tune/scroll control knob a third time and treble will display. Turn the tune/scroll control knob to the right or left to increase or decrease the treble tones. Push the rotary tune/scroll control knob a fourth time and balance will display. Turn the tune/ scroll control knob to the r...

  • Page 363

    Every time a preset button is used, a corresponding button number will display. Buttons 1 - 6 these buttons tune the radio to the stations that you commit to pushbutton memory (12 am and 12 fm stations). Disc button pressing the disc button will allow you to switch from am/fm modes to disc modes. Op...

  • Page 364

    Caution! • this cd player will accept 4–3/4 in (12 cm) discs only. The use of other sized discs may damage the cd player mechanism. • do not use adhesive labels. These labels can peel away and jam the player mechanism. • the uconnect® 130 is a single cd player. Do not attempt to insert a second cd i...

  • Page 365

    Rw/ff press and hold the ff (fast forward) button and the cd player will begin to fast forward until ff is released, or rw or another cd button is pressed. The rw (reverse) button operates in a similar manner. Am/fm button press the button to select either am or fm mode. Set/rnd button (random play ...

  • Page 366

    The radio uses the following limits for file systems: • maximum number of folder levels: 8 • maximum number of files: 255 • maximum number of folders. (the radio display of file names and folder names is limited. For large numbers of files and/or folders, the radio may be unable to display the file ...

  • Page 367

    Mpeg specifi- cation sampling fre- quency (khz) bit rate (kbps) mpeg-1 audio layer 3 48, 44.1, 32 320, 256, 224, 192, 160, 128, 112, 96, 80, 64, 56, 48, 40, 32 mpeg-2 audio layer 3 24, 22.05, 16 160, 128, 144, 112, 96, 80, 64, 56, 48, 40, 32, 24, 16, 8 id3 tag information for artist, song title, and...

  • Page 368

    Operation instructions — auxiliary mode the auxiliary (aux) jack is an audio input jack, which allows the user to plug in a portable device, such as an mp3 player, or ipod®, and utilize the vehicle’s audio system to amplify the source and play through the vehicle speakers. Pressing the disc/aux butt...

  • Page 369

    Power switch/volume control (rotary) push the on/volume control knob to turn on the radio. Push the on/volume control knob a second time to turn off the radio. Electronic volume control the electronic volume control turns continuously (360 degrees) in either direction, without stopping. Turning the ...

  • Page 370

    Phone button uconnect® phone — if equipped press this button to operate the uconnect® phone feature (if equipped). Refer to “uconnect® phone” in “under- standing the features of your vehicle”. If your vehicle is not equipped with or this feature is not available on your vehicle, a “not equipped with...

  • Page 371

    Info button press the info button for an rds station (one with call letters displayed). The radio will return a radio text message broadcast from an fm station (fm mode only). Rw/ff pressing the rw (rewind) or ff (fast forward) buttons causes the tuner to search for the next frequency in the directi...

  • Page 372

    Push the rotary tune/scroll control knob again to exit setting tone, balance, and fade. Music type button pressing this button once will turn on the music type mode for five seconds. Pressing the music type button or turning the tune/scroll control knob within five seconds will allow the program for...

  • Page 373

    Program type 16-digit character dis- play religious talk rel talk rock rock soft soft soft rock soft rck soft rhythm and blues soft r&b sports sports talk talk top 40 top 40 weather weather by pressing the seek button when the music type icon is displayed, the radio will be tuned to the next frequen...

  • Page 374

    Set/rnd button — to set the pushbutton memory when you are receiving a station that you wish to commit to pushbutton memory, press the set/rnd button. The symbol set 1 will now show in the display window. Select the button (1–6) you wish to lock onto this station and press and release that button. I...

  • Page 375

    • this radio is capable of playing compact discs (cd), recordable compact discs (cd-r), rewritable compact discs (cd-rw), compact discs with mp3 tracks and multisession compact discs with cd and mp3 tracks. Inserting compact disc(s) gently insert one cd into the cd player with the cd label facing up...

  • Page 376

    Eject button — ejecting a cd press the eject button to eject the cd. If you have ejected a disc and have not removed it within 10 seconds, it will be reloaded. If the cd is not removed, the radio will reinsert the cd but will not play it. A disc can be ejected with the radio and ignition off. Note: ...

  • Page 377

    Set/rnd button (random play button) press this button while the cd is playing to activate random play. This feature plays the selections on the compact disc in random order to provide an interesting change of pace. Press the right seek button to move to the next ran- domly selected track. Press the ...

  • Page 378

    • maximum number of folders. (the radio display of file names and folder names is limited. For large numbers of files and/or folders, the radio may be unable to display the file name and folder name, and will assign a number instead. With a maximum number of files, exceeding 20 folders will result i...

  • Page 379

    Mpeg specifi- cation sampling fre- quency (khz) bit rate (kbps) mpeg-1 audio layer 3 48, 44.1, 32 320, 256, 224, 192, 160, 128, 112, 96, 80, 64, 56, 48, 40, 32 mpeg-2 audio layer 3 24, 22.05, 16 160, 128, 144, 112, 96, 80, 64, 56, 48, 40, 32, 24, 16, 8 id3 tag information for artist, song title, and...

  • Page 380

    To increase the speed of disc loading, it is recommended to use cd-r media and single-session discs. To create a single-session disc, enable the “disc at once” option before writing to the disc. List button — cd mode for mp3 play pressing the list button will bring up a list of all folders on the di...

  • Page 381

    Note: the aux device must be turned on and the device’s volume set to the proper level. If the aux audio is not loud enough, turn the device’s volume up. If the aux audio sounds distorted, turn the device’s volume down. Time button (auxiliary mode) press this button to change the display to time of ...

  • Page 382

    Electronic serial number/sirius identification number (esn/sid) please have the following information available when calling: 1. The electronic serial number/sirius identification number (esn/sid). 2. Your vehicle identification number. To access the esn/sid, refer to the following steps: esn/sid ac...

  • Page 383

    • dense tree coverage may interrupt reception in the form of short audio mutes. • driving under wide bridges or along tall buildings can cause intermittent reception. • placing objects over or too close to the antenna can cause signal blockage. Operating instructions — uconnect® (satellite) mode not...

  • Page 384

    Rw/ff pressing the rw (rewind) or ff (fast forward) buttons causes the tuner to search for the next channel in the direction of the arrows. Tune control (rotary) turn the rotary tune/scroll control knob clockwise to increase or counterclockwise to decrease the channel. Music type button pressing thi...

  • Page 385

    Select the button (1-6) you wish to lock onto this channel and press and release that button. If a button is not selected within five seconds after pressing the set but- ton, the channel will continue to play but will not be stored into pushbutton memory. You may add a second channel to each pushbut...

  • Page 386

    Note: • if the radio has a usb port, refer to the appropriate uconnect® supplement manual for ipod® or external usb device support capability. • connecting an ipod® or consumer electronic audio device to the aux port located in the radio faceplate, plays media, but does not use the ipod®/mp3 control...

  • Page 387

    External usb device may take a few minutes to connect), the audio device starts charging and is ready for use by pressing radio switches, as described below. Note: if the audio device battery is completely dis- charged, it may not communicate with the ipod®/usb/ mp3 control system until a minimum ch...

  • Page 388

    Play mode when switched to ipod®/usb/mp3 control mode, the ipod® or external usb device automatically starts play mode. In play mode, the following buttons on the radio faceplate may be used to control the ipod® or external usb device and display data: • use the tune control knob to select the next ...

  • Page 389

    • while a track is playing, press the info button to see the associated metadata (artist, track title, album, etc.) for that track. Pressing the info button again jumps to the next screen of data for that track. Once all screens have been viewed, the last info button press will go back to the play m...

  • Page 390

    Played is highlighted on the radio display, press the tune control knob to select and start playing the track. Turning the tune control knob fast will scroll through the list faster. During fast scroll, a slight delay in updating the information on the radio display may be noticeable. • during all l...

  • Page 391

    • music type button: the music type button is another shortcut button to the genre listing on your audio device. Caution! • leaving the ipod® or external usb device (or any supported device) anywhere in the vehicle in ex- treme heat or cold can alter the operation or dam- age the device. Follow the ...

  • Page 392

    Device first, then it will get streamed to the uconnect® phone system. Seven devices can be paired to the uconnect® phone system, but just one can be selected and played. Selecting a different audio device 1. Press the phone button to begin. 2. After the ⬙ ready ⬙ prompt and following the beep, say ...

  • Page 393

    The right-hand control is a rocker-type switch with a push-button in the center and controls the volume and mode of the sound system. Pressing the top of the rocker switch will increase the volume, and pressing the bottom of the rocker switch will decrease the volume. Pressing the center button will...

  • Page 394

    Cd player pressing the top of the switch once will go to the next track on the cd. Pressing the bottom of the switch once will go to the beginning of the current track, or to the beginning of the previous track if it is within eight seconds after the current track begins to play. If you press the sw...

  • Page 395

    Radio operation and mobile phones under certain conditions, the mobile phone being on in your vehicle can cause erratic or noisy performance from your radio. This condition may be lessened or eliminated by relocating the mobile phone antenna. This condition is not harmful to the radio. If your radio...

  • Page 396

    Blower control rotate this control to regulate the amount of air forced through the ven- tilation system in any mode. The blower speed increases as you move the control to the right from the “o” (off) position. There are seven blower speeds. Note: for vehicles equipped with remote start, the climate...

  • Page 397

    Mode control (air direction) rotate this control to choose from sev- eral patterns of air distribution. You can select either a primary mode as identified by the symbols on the con- trol, or a blend of two of these modes. The closer the setting is to a particular symbol, the more air distribution yo...

  • Page 398

    Mix air is directed through the floor, defrost, and side window demist outlets. This setting works best in cold or snowy conditions that require extra heat to the windshield. This setting is good for maintaining comfort while reducing moisture on the windshield. Defrost air is directed through the w...

  • Page 399

    • the a/c will engage automatically to prevent fogging when the recirculation button is pressed and the mode control is set to panel or bi-level. • the a/c can be deselected manually without disturb- ing the mode control selection. • when the ignition switch is turned to the lock position, the recir...

  • Page 400

    Automatic temperature control (atc) — if equipped automatic operation the automatic temperature control system automati- cally maintains the climate in the cabin of the vehicle at the comfort levels desired by the driver and passenger. Operation of the system is quite simple. Turn the mode control k...

  • Page 401

    Temperature control dial in the temperature you would like the system to maintain by rotating the temperature control knob. Once the comfort level is selected, the system will maintain that level automatically using the heating system. Should the desired comfort level require air conditioning, the s...

  • Page 402

    • while operating in auto, the system will not auto- matically sense the presence of fog, mist or ice on the windshield. The defrost mode must be manually se- lected to clear the windshield and side glass. Blower control for full automatic operation or for automatic blower operation, turn the knob t...

  • Page 403

    4 understanding your instrument panel 401.

  • Page 404

    The operator can override the auto mode setting to change airflow distribution by rotating the mode control knob (on the right) to one of the following positions: • panel air is directed through the outlets in the instru- ment panel. These outlets can be adjusted to direct airflow. Note: the center ...

  • Page 405

    • defrost air is directed through the windshield and side window demist outlets. Use this mode with maxi- mum blower and temperature settings for best wind- shield and side window defrosting. • air conditioner control press this button to turn on the air conditioning during manual operation only. Wh...

  • Page 406

    • extended use of recirculation may cause the windows to fog. If the interior of the windows begins to fog, press the recirculation button to return to outside air. Some temp/humidity conditions will cause captured interior air to condense on windows and hamper visibility. For this reason, the syste...

  • Page 407

    Summer operation the engine cooling system must be protected with a high-quality antifreeze coolant to provide proper corro- sion protection and to protect against engine overheating. A solution of 50% oat (organic additive technology) coolant that meets the requirements of chrysler material standar...

  • Page 408

    Side window demisters a side window demister outlet is located at each end of the instrument panel. These non-adjustable outlets direct air toward the side windows when the system is in the floor, mix, or defrost mode. The air is directed at the area of the windows through which you view the outside...

  • Page 409

    Control setting suggestions for various weather conditions 4 understanding your instrument panel 407.

  • Page 411: Starting And Operating

    Starting and operating contents 䡵 starting procedures . . . . . . . . . . . . . . . .414 ▫ manual transmission — if equipped . . . . . . .414 ▫ automatic transmission — if equipped . . . . .415 ▫ normal starting. . . . . . . . . . . . . . . . . . . . . . .415 ▫ extreme cold weather (below –20°f or −...

  • Page 412

    䡵 autostick® . . . . . . . . . . . . . . . . . . . . . . . . .432 ▫ operation . . . . . . . . . . . . . . . . . . . . . . . . . . .433 䡵 four–wheel drive operation (command- trac i® or rock-trac®) . . . . . . . . . . . . . .434 ▫ operating instructions/precautions . . . . . . . .435 ▫ shift position...

  • Page 413

    䡵 anti-lock brake system . . . . . . . . . . . . .461 䡵 electronic brake control system . . . .462 ▫ anti-lock brake system (abs) . . . . . . . . . . . .463 ▫ traction control system (tcs) . . . . . . . . . . . .463 ▫ brake assist system (bas) . . . . . . . . . . . . . . .464 ▫ hill start assist (hs...

  • Page 414

    ▫ tread wear indicators . . . . . . . . . . . . . . . . . .499 ▫ life of tire . . . . . . . . . . . . . . . . . . . . . . . . .500 ▫ replacement tires . . . . . . . . . . . . . . . . . . . . .501 䡵 tire chains (traction devices) . . . . . . .503 䡵 tire rotation recommendations . . . . .504 䡵 tire pr...

  • Page 415

    ▫ trailer towing weights (maximum trailer weight ratings) . . . . . . . . . . . . . . . . . . . . . .530 ▫ trailer and tongue weight . . . . . . . . . . . . . .537 ▫ towing requirements . . . . . . . . . . . . . . . . . .538 ▫ towing tips . . . . . . . . . . . . . . . . . . . . . . . . .543 䡵 recrea...

  • Page 416

    Starting procedures before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. Warning! • when leaving the vehicle, always remove the key fob from the ignition and lock your vehicle. • never leave children alone in a vehicle, or with access to...

  • Page 417

    The “4wd indicator light” will illuminate when the transfer case has been shifted into this mode. Automatic transmission — if equipped start the vehicle with the shift lever in the park position (vehicle can also be started in neutral). Apply the brake before shifting to any driving range. Normal st...

  • Page 418

    If engine fails to start warning! • never pour fuel or other flammable liquids into the throttle body air inlet opening in an attempt to start the vehicle. This could result in a flash fire causing serious personal injury. • do not attempt to push or tow your vehicle to get it started. Vehicles equi...

  • Page 419

    Caution! To prevent damage to the starter, do not crank the engine for more than 15 seconds at a time. Wait 10 to 15 seconds before trying again. If the engine has been flooded, it may start to run, but not have enough power to continue running when the key is released. If this occurs, continue cran...

  • Page 420

    After starting the idle speed is controlled automatically and it will decrease as the engine warms up. Engine block heater — if equipped the engine block heater warms the engine, and permits quicker starts in cold weather. Connect the cord to a standard 110-115 volt ac electrical outlet with a groun...

  • Page 421

    Caution! Never drive with your foot resting on the clutch pedal, or attempt to hold the vehicle on a hill with the clutch pedal partially engaged, as this will cause abnormal wear on the clutch. Note: during cold weather, you may experience in- creased effort in shifting until the transmission fluid...

  • Page 422

    Recommended vehicle shift speeds to utilize your manual transmission efficiently for both fuel economy and performance, it should be upshifted as listed in recommended shift speed chart. Shift at the vehicle speeds listed for acceleration. When heavily loaded or pulling a trailer these recommended u...

  • Page 423

    Caution! • skipping gears and downshifting into lower gears at higher vehicle speeds can damage the engine and clutch systems, any attempt to shift into lower gear with clutch pedal depressed may result dam- age to the clutch system. Shifting into lower gear and releasing the clutch may result in en...

  • Page 424

    Manual transmission downshift speeds in mph (km/h) gear selection 6 to 5 5 to 4 4 to 3 3 to 2 2 to 1 maximum speed 80 (129) 70 (113) 50 (81) 30 (48) 15 (24) note: vehicle speeds shown in the chart above are for 2h and 4h only, vehicle speeds in 4l would be signifi- cantly less. Reverse shifting to s...

  • Page 425

    Automatic transmission — if equipped caution! Damage to the transmission may occur if the follow- ing precautions are not observed: • shift into park only after the vehicle has come to a complete stop. • shift into or out of reverse only after the vehicle has come to a complete stop and the engine i...

  • Page 426

    Warning! (continued) • never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking bra...

  • Page 427

    Note: if a malfunction occurs, the system will trap the key in the ignition switch to warn you that this safety feature is inoperable. The engine can be started and stopped but the key cannot be removed until you obtain service. Brake/transmission shift interlock system this vehicle is equipped with...

  • Page 428

    Manually select the transmission gear and will display the current gear in the instrument cluster as 5, 4, 3, 2, 1. Gear ranges do not race the engine when shifting from park or neutral into another gear range. Note: • after selecting any gear range, wait a moment to allow the selected gear to engag...

  • Page 429

    When parking on a level surface, you may shift the transmission into park first, and then apply the parking brake. When parking on a hill, apply the parking brake before shifting the transmission to park, otherwise the load on the transmission locking mechanism may make it diffi- cult to move the sh...

  • Page 430

    Warning! (continued) • it is dangerous to shift out of park or neutral if the engine speed is higher than idle speed. If your foot is not firmly pressing the brake pedal, the vehicle could accelerate quickly forward or in re- verse. You could lose control of the vehicle and hit someone or something....

  • Page 431

    Warning! (continued) • never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking bra...

  • Page 432

    • look at the transmission gear position display and verify that it indicates the park position. • with brake pedal released, verify that the shift lever will not move out of park. Reverse (r) this range is for moving the vehicle backward. Shift into reverse only after the vehicle has come to a comp...

  • Page 433

    Drive (d) this range should be used for most city and highway driving. It provides the smoothest upshifts and down- shifts, and the best fuel economy. The transmission automatically upshifts through underdrive first, second, and third gears, direct fourth gear and overdrive fifth gear. The drive pos...

  • Page 434

    2. Shift the transmission into park. 3. Turn the ignition switch to the lock/off position. 4. Wait approximately 10 seconds. 5. Restart the engine. 6. Shift into the desired gear range. If the problem is no longer detected, the transmission will return to normal operation. Note: even if the transmis...

  • Page 435

    This system can also provide you with more control during passing, city driving, cold slippery conditions, mountain driving, trailer towing, and many other situa- tions. Operation when the shift lever is in the drive position, the transmission will operate automatically, shifting between the five av...

  • Page 436

    • you can start out, from a stop, in first or second gear. Tapping (+) (at a stop) will allow starting in second gear. Starting out in second gear is helpful in snowy or icy conditions. • the system will ignore attempts to upshift at too low of a vehicle speed. • avoid using speed control when autos...

  • Page 437

    Operating instructions/precautions the transfer case provides four mode positions: • 2h (two-wheel drive high range) • 4h (four-wheel drive high range) • n (neutral) • 4l (four-wheel drive low range) the transfer case is intended to be driven in the 2h position for normal street and highway conditio...

  • Page 438

    Rear wheels to rotate at the same speed. The 4h and 4l positions are intended for loose, slippery road surfaces only and not intended for normal driving. Driving in the 4h and 4l positions on hard-surfaced roads will cause increased tire wear and damage to the driveline compo- nents. Refer to “shift...

  • Page 439

    Warning! (continued) the parking brake. The transfer case neutral (n) position disengages both the front and rear drive shaft from the powertrain, and will allow the vehicle to move regardless of the transmission position. The parking brake should always be applied when the driver is not in the vehi...

  • Page 440

    The “4wd indicator light” (located in the instrument cluster) will illuminate when the transfer case is shifted into the 4l position. Note: when in 4wd, the “esc off indicator light” will display in the instrument cluster. Shifting procedure 2h to 4h or 4h to 2h shifting between 2h and 4h can be mad...

  • Page 441

    Warning! Failure to engage a transfer case position completely can cause transfer case damage or loss of power and vehicle control. You could have a collision. Do not drive the vehicle unless the transfer case is fully engaged. Trac-lok® rear axle — if equipped the trac-lok® rear axle provides a con...

  • Page 442

    This feature will only activate when the following con- ditions are met: • key in ignition, vehicle in 4l (low) range. • vehicle speed should be 10 mph (16 km/h) or less. To activate the system, press the bottom of the axle lock switch once to lock the rear axle only (the “rear axle lock indicator l...

  • Page 443

    Electronic sway bar disconnect — if equipped your vehicle may be equipped with an electronic discon- necting stabilizer/sway bar. This system allows greater front suspension travel in off-road situations. This system is controlled by the sway bar switch located on the instrument panel (to the left o...

  • Page 444

    Sway bar should remain in on-road mode during normal driving conditions. Warning! Do not disconnect the stabilizer bar and drive on hard-surfaced roads or at speeds above 18 mph (29 km/h); you may lose control of the vehicle, which could result in serious injury. The front stabilizer bar enhances ve...

  • Page 445

    Warning! If the stabilizer/sway bar will not return to on-road mode, the “sway bar indicator light” will flash in the instrument cluster and vehicle stability is greatly reduced. Do not attempt to drive the vehicle over 18 mph (29 km/h). Driving faster than 18 mph (29 km/h) may cause loss of control...

  • Page 446

    2. Remove one bolt from the underside of the vehicle. 3. Remove the side step assembly. Bodyside nut underside bolt 444 starting and operating.

  • Page 447

    The basics of off-road driving you will encounter many types of terrain driving off- road. You should be familiar with the terrain and area before proceeding. There are many types of surface conditions: hard-packed dirt, gravel, rocks, grass, sand, mud, snow and ice. Every surface has a different ef...

  • Page 448

    Is needed. Vehicle speeds in excess of 25 mph (40 km/h) should be avoided when in 4l (low) range. Caution! Do not use 4l (low) range when operating the vehicle on dry pavement. Driveline hardware dam- age can result. Simultaneous brake and throttle operation many off-road driving conditions require ...

  • Page 449

    Mud deep mud creates a great deal of suction around the tires and is very difficult to get through. You should use second gear (manual transmission), or drive (automatic transmission), with the transfer case in the 4l (low) position to maintain your momentum. If you start to slow to a stop, try turn...

  • Page 450

    Crossing obstacles (rocks and other high points) while driving off-road, you will encounter many types of terrain. These varying types of terrain bring different types of obstacles. Before proceeding, review the path ahead to determine the correct approach and your ability to safely recover the vehi...

  • Page 451

    Caution! • never attempt to straddle a rock that is large enough to strike your axles or undercarriage. • never attempt to drive over a rock which is large enough to contact the door sills. Crossing a ravine, gully, ditch, washout or rut when crossing a ravine, gully, ditch, washout or a large rut, ...

  • Page 452

    Caution! Do not attempt to cross a log with a greater diameter than the running ground clearance or the vehicle will become high-centered. Getting high-centered if you get hung up or high-centered on an object, get out of the vehicle and try to determine what the vehicle is hung up on, where it is c...

  • Page 453

    Branches or other obstacles on the path? Can you safely recover the vehicle if something goes wrong? If every- thing looks good and you feel confident, shift the trans- mission into a lower gear with 4l (low) engaged, and proceed with caution, maintaining your momentum as you climb the hill. Driving...

  • Page 454

    Controlled descent? Are there obstacles? Is it a straight descent? Is there plenty of distance at the base of the hill to regain control if the vehicle descends to fast? If you feel confident in your ability to proceed, then make sure you are in 4l (low) and proceed with caution. Allow engine brakin...

  • Page 455

    Warning! If the engine stalls or you lose headway or cannot make it to the top of a steep hill or grade, never attempt to turn around. To do so may result in tipping and rolling the vehicle, which may result in severe injury. Always back carefully straight down a hill in reverse. Never back down a h...

  • Page 456

    Caution! • water ingestion into the axles, transmission, trans- fer case, engine or vehicle interior can occur if you drive too fast or through too deep of water. Water can cause permanent damage to engine, driveline or other vehicle components, and your brakes will be less effective once wet and/or...

  • Page 457

    Caution! Muddy waters can reduce the cooling system effec- tiveness by depositing debris onto the radiator. Crossing ditches, streams, shallow rivers or other flowing water flowing water can be extremely dangerous. Never at- tempt to cross a fast running stream or river even in shallow water. Fast m...

  • Page 458

    Always a good idea to check for damage. That way you can get any problems taken care of right away and have your vehicle ready when you need it. • completely inspect the underbody of your vehicle. Check tires, body structure, steering, suspension, and exhaust system for damage. • inspect the radiato...

  • Page 459

    Power steering the standard power steering system will give you good vehicle response and increased ease of maneuverability in tight spaces. The system will provide mechanical steering capability if power assist is lost. If for some reason the power assist is interrupted, it will still be possible t...

  • Page 460

    Caution! Do not use chemical flushes in your power steering system as the chemicals can damage your power steering components. Such damage is not covered by the new vehicle limited warranty. Warning! Fluid level should be checked on a level surface and with the engine off to prevent injury from movi...

  • Page 461

    When the parking brake is applied with the ignition switch on, the “brake warning light” in the instrument cluster will illuminate. Note: • when the parking brake is applied and the automatic transmission is placed in gear, the “brake warning light” will flash. If vehicle speed is detected, a chime ...

  • Page 462

    Warning! • never use the park position on an automatic transmission as a substitute for the parking brake. Always apply the parking brake fully when parked to guard against vehicle movement and possible injury or damage. • when leaving the vehicle, always remove the key fob from the ignition and loc...

  • Page 463

    Caution! If the “brake warning light” remains on with the parking brake released, a brake system malfunction is indicated. Have the brake system serviced by an authorized dealer immediately. Anti-lock brake system the anti-lock brake system (abs) is designed to aid the driver in maintaining vehicle ...

  • Page 464

    Warning! • pumping of the anti-lock brakes will diminish their effectiveness and may lead to a collision. Pumping makes the stopping distance longer. Just press firmly on your brake pedal when you need to slow down or stop. • the anti-lock brake system (abs) cannot prevent the natural laws of physic...

  • Page 465

    (hdc). All of these systems work together to enhance vehicle stability and control in various driving condi- tions, and are commonly referred to as esc. Anti-lock brake system (abs) this system aids the driver in maintaining vehicle control under adverse braking conditions. The system controls hydra...

  • Page 466

    Will allow more engine torque to be applied to the wheel that is not spinning. This feature remains active even if tcs and esc are in either the “partial off” or “full off” modes. Refer to “electronic stability control (esc)” in this section for further information. Brake assist system (bas) the bas...

  • Page 467

    The level of brake pressure the driver applied for a short period of time after the driver takes their foot off of the brake pedal. If the driver does not apply the throttle during this short period of time, the system will release brake pressure and the vehicle will roll down the hill. The system w...

  • Page 468

    Warning! (continued) could cause a collision with another vehicle or object. Always remember the driver is responsible for brak- ing the vehicle. The system will only work if the intended direction of the vehicle and vehicle gear match. For example, if the intended direction is forward up a hill and...

  • Page 469

    Warning! • if you use a trailer brake controller with your trailer, your trailer brakes may be activated and deactivated with the brake switch. If so, when the brake pedal is released there may not be enough brake pressure to hold the vehicle and trailer on a hill and this could cause a collision wi...

  • Page 470

    Hsa off if you wish to turn off the hsa system, follow this procedure: 1. Start with the engine off and vehicle in park (auto- matic transmission) or neutral with clutch out (manual transmission) with wheels straight. Apply parking brake on manual transmission vehicle. 2. Start the engine. 3. With t...

  • Page 471

    Electronic roll mitigation (erm) can only reduce the chance of wheel lift occurring during severe or evasive driving maneuvers. It cannot prevent wheel lift due to other factors such as road conditions, leaving the road- way or striking objects or other vehicles. Note: anytime the esc system is in t...

  • Page 472

    The intended path, esc applies the brake of the appro- priate wheel to assist in counteracting the oversteer or understeer condition. • oversteer - when the vehicle is turning more than appropriate for the steering wheel position. • understeer - when the vehicle is turning less than appropriate for ...

  • Page 473

    The esc system has three available operating modes in 4h range. The system has one operating mode in 4l range. Two-wheel drive vehicles and four-wheel drive vehicles in 2h range have two operating modes. 4h range (4wd models) on this is the normal operating mode for esc in 4h range. Partial off this...

  • Page 474

    Warning! • when in “partial off” mode, the tcs functionality of esc, (except for the limited slip feature de- scribed in the tcs section), has been disabled and the “esc off indicator light” will be illuminated. When in “partial off” mode, the engine power reduction feature of tcs is disabled, and t...

  • Page 475

    When in esc off mode, esc and tcs, except for the brake limited differential (bld) feature described in the tcs section, are turned off until the vehicle reaches a speed of 40 mph (64 km/h). For speeds at or exceeding 40 mph (64 km/h) the esc goes into partial off. When the vehicle speed drops below...

  • Page 476

    Note: the “esc off” message will display and the audible chime will sound when the shift lever is placed in the park position from any position other than park, and then moved out of the park position. This will occur even if the message was previously cleared. Warning! In the esc ⴖ full off ⴖ mode,...

  • Page 477

    Note: to improve the vehicle’s traction when driving with snow chains, or starting off in deep snow, sand, or gravel, it may be desirable to switch to the ⬙ partial off ⬙ mode by pressing the esc off switch. Once the situation requiring esc to be switched to the ⬙ partial off ⬙ mode is overcome, tur...

  • Page 478

    Esc activation/malfunction indicator light and esc off indicator light the “esc activation/malfunction indicator light” in the instrument cluster will come on when the ignition switch is cycled to the on position. It should go out with the engine running. If the “esc activation/malfunction indicator...

  • Page 479

    • the esc system will make buzzing or clicking sounds when it is active. This is normal; the sounds will stop when esc becomes inactive following the maneuver that caused the esc activation. The “esc off indicator light” indicates the electronic stability control (esc) is partially off or full off. ...

  • Page 480

    Hill descent control (hdc) — if equipped hdc is only intended for low speed off-road driving. Hdc maintains vehicle speed while descending hills in off-road driving conditions by applying the brakes when necessary. The symbol indicates the status of the hill descent control (hdc) feature. The lamp w...

  • Page 481

    However, the driver can override hdc operation by applying the brake to slow the vehicle down below the hdc control speed. If more speed is desired during hdc control, the accelerator pedal will increase vehicle speed in the usual manner. When either the brake or the accelerator is released, hdc wil...

  • Page 482

    Tire safety information tire markings note: • p (passenger) - metric tire sizing is based on u.S. Design standards. P-metric tires have the letter “p” molded into the sidewall preceding the size designa- tion. Example: p215/65r15 95h. • european-metric tire sizing is based on european design standar...

  • Page 483

    • temporary spare tires are designed for temporary emergency use only. Temporary high pressure com- pact spare tires have the letter “t” or “s” molded into the sidewall preceding the size designation. Example: t145/80d18 103m. • high flotation tire sizing is based on u.S. Design standards and it beg...

  • Page 484

    Example: r = construction code — ⬙ r ⬙ means radial construction — ⬙ d ⬙ means diagonal or bias construction 15 = rim diameter in inches (in) service description: 95 = load index — a numerical code associated with the maximum load a tire can carry h = speed symbol — a symbol indicating the range of ...

  • Page 485

    Example: load identification: ⴖ ....Blank.... ⴖ = absence of any text on the sidewall of the tire indicates a standard load (sl) tire extra load (xl) = extra load (or reinforced) tire light load (ll) = light load tire c, d, e, f, g = load range associated with the maximum load a tire can carry at a ...

  • Page 486

    Example: dot ma l9 abcd 0301 dot = department of transportation — this symbol certifies that the tire is in compliance with the u.S. Department of transportation tire safety standards and is approved for highway use ma = code representing the tire manufacturing location (two digits) l9 = code repres...

  • Page 487

    Tire terminology and definitions term definition b-pillar the vehicle b-pillar is the structural member of the body located behind the front door. Cold tire inflation pressure cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least 3 hours, or ...

  • Page 488

    Tire loading and tire pressure tire placard location tire placard location (two-door model) tire placard location (four-door model) 486 starting and operating.

  • Page 489

    Tire and loading information placard this placard tells you important information about the: 1. Number of people that can be carried in the vehicle. 2. Total weight your vehicle can carry. 3. Tire size designed for your vehicle. 4. Cold tire inflation pressures for the front, rear, and spare tires. ...

  • Page 490

    Loading the vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size, and cold tire inflation pressures specified on the tire and loading informati...

  • Page 491

    4. The resulting figure equals the available amount of cargo and luggage load capacity. For example, if “xxx” amount equals 1,400 lbs (635 kg) and there will be five 150 lb (68 kg) passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lbs (295 kg) (since 5 x 150 ...

  • Page 492

    490 starting and operating.

  • Page 493

    Warning! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. Tires — general information tire pressure proper tire inflation pressur...

  • Page 494

    Warning! (continued) • unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left. • always drive with each tire inflated to the recom- mended cold tire inflation pressure. Economy improper inflation pressures can cause uneven wear pat- terns...

  • Page 495

    • inspect tires for signs of tire wear or visible damage. Caution! After inspecting or adjusting the tire pressure, al- ways reinstall the valve stem cap. This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Inflation pressures specified on the placard...

  • Page 496

    Tire pressures for high speed operation the manufacturer advocates driving at safe speeds and within posted speed limits. Where speed limits or condi- tions are such that the vehicle can be driven at high speeds, maintaining correct tire inflation pressure is very important. Increased tire pressure ...

  • Page 497

    Consult an authorized tire dealer for tire repairs and additional information. Damaged run flat tires, or run flat tires that have experienced a loss of pressure should be replaced imme- diately with another run flat tire of identical size and service description (load index and speed code). Tire ty...

  • Page 498

    If you need snow tires, select tires equivalent in size and type to the original equipment tires. Use snow tires only in sets of four; failure to do so may adversely affect the safety and handling of your vehicle. Snow tires generally have lower speed ratings than what was originally equipped with y...

  • Page 499

    Spare tires — if equipped note: for vehicles equipped with tirefit instead of a spare tire, please refer to “tirefit kit” in “what to do in emergencies” for further information. Caution! Because of the reduced ground clearance, do not take your vehicle through an automatic car wash with a compact, f...

  • Page 500

    Do not install a wheel cover or attempt to mount a conventional tire on the compact spare wheel, since the wheel is designed specifically for the compact spare tire. Do not install more than one compact spare tire and wheel on the vehicle at any given time. Warning! Compact spares are for temporary ...

  • Page 501

    Warning! Limited-use spares are for emergency use only. In- stallation of this limited-use spare tire affects vehicle handling. With this tire, do not drive more than the speed listed on the limit-use spare wheel. Keep inflated to the cold tire inflation pressures listed on your tire and loading inf...

  • Page 502

    These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth becomes 1/16 in (2 mm). When the tread is worn to the tread wear indicators, the tire should be replaced. Refer to “replacement tires” in this section for further infor- mation. Life of t...

  • Page 503

    Warning! Tires and the spare tire should be replaced after six years, regardless of the remaining tread. Failure to follow this warning can result in sudden tire failure. You could lose control and have a collision resulting in serious injury or death. Keep dismounted tires in a cool, dry place with...

  • Page 504

    It is recommended you contact your authorized tire dealer or original equipment dealer with any questions you may have on tire specifications or capability. Failure to use equivalent replacement tires may adversely affect the safety, handling, and ride of your vehicle. Warning! • do not use a tire, ...

  • Page 505

    Tire chains (traction devices) use of traction devices require sufficient tire-to-body clearance. Follow these recommendations to guard against damage. • traction device must be of proper size for the tire, as recommended by the traction device manufacturer. • install on rear tires only. • p225/75r1...

  • Page 506

    Caution! (continued) • observe the traction device manufacturer’s instruc- tions on the method of installation, operating speed, and conditions for use. Always use the suggested operating speed of the device manufac- turer’s if it is less than 30 mph (48 km/h). • do not use traction devices on a com...

  • Page 507

    Caution! Proper operation of four-wheel drive vehicles de- pends on tires of equal size, type and circumference on each wheel. Any difference in tire size can cause (continued) caution! (continued) damage to the transfer case. Tire rotation schedule should be followed to balance tire wear. Tire pres...

  • Page 508

    Pressure will also increase as the vehicle is driven; this is normal and there should be no adjustment for this increased pressure. The tpms will warn the driver of a low tire pressure if the tire pressure falls below the low pressure warning threshold for any reason, including low temperature effec...

  • Page 509

    Caution! • the tpms has been optimized for the original equipment tires and wheels. The tpms pressures have been established for the tire size equipped on your vehicle. Undesirable system operation or sen- sor damage may result when using replacement equipment that is not of the same size, type, and...

  • Page 510

    • driving on a significantly under-inflated tire causes the tire to overheat and can lead to tire failure. Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability. • the tpms is not a substitute for proper tire mainte- nance, and i...

  • Page 511

    A tire pressure monitoring sensor is located in the spare wheel if the vehicle is equipped with a matching full size spare wheel and tire assembly. The matching full size spare tire can be used in place of any of the four road tires. A low spare tire will not cause the “tire pressure monitoring tell...

  • Page 512

    Tire location will be displayed as follows: lf = l eft f ront rf = r ight f ront lr = l eft r ear rr = r ight r ear premium tire pressure monitoring vehicles equipped with a evic will display specific tire pressure information. When tire pressure is low, the low tire iso telltale will illuminate and...

  • Page 513

    Note: • if your vehicle is equipped with a matching full-size spare wheel and tire assembly, it has a tire pressure monitoring sensor, and can be monitored by the tire pressure monitoring system (tpms). In the event that the matching full-size spare tire is swapped with a low pressure road tire, the...

  • Page 514

    Premium system — if equipped the tire pressure monitor system (tpms) uses wireless technology with wheel rim-mounted electronic sensors to monitor tire pressure levels. Sensors, mounted to each wheel as part of the valve stem, transmit tire pressure readings to the receiver module. Note: it is parti...

  • Page 515

    Tire pressure monitoring low pressure warnings the tire pressure monitoring telltale light will illuminate in the instrument cluster, and an au- dible chime will be activated, when one or more of the four active road tire pressures are low. In addition, the evic will display a “low tire pressure” me...

  • Page 516

    The pressure value(s) will stop “flashing,” and the tire pressure monitoring telltale light will extinguish once the updated tire pressure(s) have been received. The vehicle may need to be driven for up to 20 minutes above 15 mph (24 km/h) to receive this information. Service tpm system warning the ...

  • Page 517

    The evic will also display a ⬙ service tpm system ⬙ message for a minimum of five seconds when a system fault is detected possibly related to an incorrect sensor location fault. In this case, the ⬙ service tpm system ⬙ message is then followed by a graphic display, with pressure values still shown. ...

  • Page 518

    Minutes above 15 mph (24 km/h), the “tire pressure monitoring telltale light” will flash on and off for 75 seconds and then remain on solid. In addition, the evic will display a “service tpm system ⬙ mes- sage for a minimum of five seconds and then display dashes (- -) in place of the pressure value...

  • Page 519

    Fuel requirements 3.6l engine this engine is designed to meet all emis- sions regulations and provide excellent fuel economy and performance when us- ing high-quality unleaded “regular” gaso- line having an octane rating of 87. The use of premium gasoline is not recommended, as it will not provide a...

  • Page 520

    Gasoline/oxygenate blends some fuel suppliers blend unleaded gasoline with oxy- genates such as ethanol. Fuels blended with oxygenates may be used in your vehicle. Caution! Do not use gasoline containing methanol or gaso- line containing more than 10% ethanol. Use of these blends may result in start...

  • Page 521

    • change the engine oil and oil filter. • disconnect and reconnect the battery to reset the engine controller memory. More extensive repairs will be required for prolonged exposure to e-85 fuel. Mmt in gasoline mmt (methylcyclopentadienyl manganese tricarbonyl) is a manganese-containing metallic add...

  • Page 522

    Fuel system cautions caution! Follow these guidelines to maintain your vehicle’s performance: • the use of leaded gas is prohibited by federal law. Using leaded gasoline can impair engine perfor- mance and damage the emissions control system. • an out-of-tune engine or certain fuel or ignition malfu...

  • Page 523

    Carbon monoxide warnings warning! Carbon monoxide (co) in exhaust gases is deadly. Follow the precautions below to prevent carbon monoxide poisoning: • do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas, which can kill. Never run the engine in a closed area, such...

  • Page 524

    Caution! • damage to the fuel system or emission control system could result from using an improper fuel cap (gas cap). A poorly fitting cap could let impu- rities into the fuel system. Also, a poorly fitting aftermarket cap can cause the “malfunction indi- cator light (mil)” to illuminate, due to f...

  • Page 525

    Warning! (continued) • never add fuel when the engine is running. This is in violation of most state and federal fire regula- tions and may cause the mil to turn on. • a fire may result if gasoline is pumped into a portable container that is inside of a vehicle. You could be burned. Always place gas...

  • Page 526

    Vehicle loading certification label as required by national highway traffic safety admin- istration regulations, your vehicle has a certification label affixed to the driver’s side door or pillar. This label contains the month and year of manufacture, gross vehicle weight rating (gvwr), gross axle w...

  • Page 527

    Tire size the tire size on the vehicle certification label represents the actual tire size on your vehicle. Replacement tires must be equal to the load capacity of this tire size. Rim size this is the rim size that is appropriate for the tire size listed. Inflation pressure this is the cold tire inf...

  • Page 528

    Items down low and be sure that the weight is distributed equally. Stow all loose items securely before driving. Improper weight distributions can have an adverse effect on the way your vehicle steers and handles and the way the brakes operate. Caution! Do not load your vehicle any heavier than the ...

  • Page 529

    Exceed the gvwr. Refer to “vehicle loading/vehicle certification label” in “starting and operating” for further information. Gross trailer weight (gtw) the gtw is the weight of the trailer plus the weight of all cargo, consumables and equipment (permanent or tem- porary) loaded in or on the trailer ...

  • Page 530

    Frontal area the frontal area is the maximum height multiplied by the maximum width of the front of a trailer. Trailer sway control – if equipped the trailer sway control is a telescoping link that can be installed between the hitch receiver and the trailer tongue. It typically provides adjustable f...

  • Page 531

    Warning! • an improperly adjusted weight distributing hitch system may reduce handling, stability, braking performance, and could result in a collision. • weight distributing systems may not be compatible with surge brake couplers. Consult with your hitch and trailer manufacturer or a reputable recr...

  • Page 532

    Trailer towing weights (maximum trailer weight ratings) the following chart provides the maximum trailer weight ratings towable for your given drivetrain. Engine/ transmission axle model gcwr (gross com- bined wt. Rating) frontal area max. Gtw (gross trailer wt.) max. Trailer tongue wt. (see note) 3...

  • Page 533

    Engine/ transmission axle model gcwr (gross com- bined wt. Rating) frontal area max. Gtw (gross trailer wt.) max. Trailer tongue wt. (see note) 3.6l/ automatic 3.73 two–door sport model (4wd) 6,340 lbs (2 876 kg) 25 sq ft (2.32 sq m) 2,000 lbs (907 kg) 200 lbs (91 kg) 3.6l/manual 3.21 two–door sahar...

  • Page 534

    Engine/ transmission axle model gcwr (gross com- bined wt. Rating) frontal area max. Gtw (gross trailer wt.) max. Trailer tongue wt. (see note) 3.6l/ automatic 3.21 two–door sahara model (4wd) 6,383 lbs (2 895 kg) 25 sq ft (2.32 sq m) 2,000 lbs (907 kg) 200 lbs (91 kg) 3.6l/ automatic 3.73 two–door ...

  • Page 535

    Engine/ transmission axle model gcwr (gross com- bined wt. Rating) frontal area max. Gtw (gross trailer wt.) max. Trailer tongue wt. (see note) 3.6l/ automatic 3.73 two–door rubicon model (4wd) 6,473 lbs (2 936 kg) 25 sq ft (2.32 sq m) 2,000 lbs (907 kg) 200 lbs (91 kg) 3.6l/ automatic 4.10 two–door...

  • Page 536

    Engine/ transmission axle model gcwr (gross com- bined wt. Rating) frontal area max. Gtw (gross trailer wt.) max. Trailer tongue wt. (see note) 3.6l/ automatic 3.21 four–door sport model (4wd) 6,780 lbs (3 075 kg) 32 sq ft (2.97 sq m) 2,000 lbs (907 kg) 200 lbs (91 kg) 3.6l/ automatic 3.73 four–door...

  • Page 537

    Engine/ transmission axle model gcwr (gross com- bined wt. Rating) frontal area max. Gtw (gross trailer wt.) max. Trailer tongue wt. (see note) 3.6l/ automatic 3.21 four–door sahara model (4wd) 6,728 lbs (3 052 kg) 32 sq ft (2.97 sq m) 2,000 lbs (907 kg) 200 lbs (91 kg) 3.6l/ automatic 3.73 four–doo...

  • Page 538

    Engine/ transmission axle model gcwr (gross com- bined wt. Rating) frontal area max. Gtw (gross trailer wt.) max. Trailer tongue wt. (see note) 3.6l/ automatic 3.73 four–door rubicon model (4wd) 8,355 lbs (3 790 kg) 32 sq ft (2.97 sq m) 3,500 lbs (1 587 kg) 350 lbs (159 kg) 3.6l/ automatic 4.10 four...

  • Page 539

    Note: the trailer tongue weight must be considered as part of the combined weight of occupants and cargo (ie. The gvwr), and the gvwr should never exceed the weight referenced on the tire and loading information placard. Refer to “tire safety information” in “starting and operating” for further info...

  • Page 540

    Note: remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options or dealer-installed options must be considered as part of the total load on your vehicle. Refer to the “tire and loading information” placard for the maximum combine...

  • Page 541

    Warning! Improper towing can lead to a collision. Follow these guidelines to make your trailer towing as safe as possible: • make certain that the load is secured in the trailer and will not shift during travel. When trailering cargo that is not fully secured, dynamic load shifts can occur that may ...

  • Page 542

    Warning! (continued) • total weight must be distributed between the tow vehicle and the trailer such that the following four ratings are not exceeded: 1. Gvwr 2. Gtw 3. Gawr 4. Tongue weight rating for the trailer hitch uti- lized. Towing requirements — tires – proper tire inflation pressures are es...

  • Page 543

    • an electronically actuated trailer brake controller is required when towing a trailer with electronically actuated brakes. When towing a trailer equipped with a hydraulic surge actuated brake system, an electronic brake controller is not required. • trailer brakes are recommended for trailers over...

  • Page 544

    The trailer tow package will include a four–pin wiring harness. Use a factory-approved trailer harness and connector. Note: do not cut or splice wiring into the vehicles wiring harness. The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector. R...

  • Page 545

    Towing tips before setting out on a trip, practice turning, stopping and backing the trailer in an area away from heavy traffic. If using a manual transmission vehicle for trailer towing, all starts must be in first gear to avoid excessive clutch slippage. Automatic transmission — if equipped the dr...

  • Page 546

    – to prevent excess heat generation, avoid continuous driving at high rpm. Reduce vehicle speed as neces- sary to avoid extended driving at high rpm. Return to a higher gear or vehicle speed when grade and road conditions allow. Electronic speed control — if equipped • do not use in hilly terrain or...

  • Page 547

    Recreational towing (behind motorhome, etc.) towing this vehicle behind another vehicle towing condition wheels off the ground four-wheel drive models flat tow none see instructions • automatic transmission in park • manual transmission in gear (not in neutral [n]) • transfer case in neutral (n) • t...

  • Page 548

    Recreational towing — four-wheel drive models note: the transfer case must be shifted into neutral (n), automatic transmission must be shifted into park, and manual transmission must be placed in gear (not in neutral) for recreational towing. Caution! • do not dolly tow any 4wd vehicle, internal dam...

  • Page 549

    Shifting into neutral (n) use the following procedure to prepare your vehicle for recreational towing. Warning! You or others could be injured or killed if you leave the vehicle unattended with the transfer case in the neutral (n) position without first fully engaging the parking brake. The transfer...

  • Page 550

    7. Shift the transmission into reverse. 8. Release the brake pedal (and clutch pedal on manual transmissions) for five seconds and ensure that there is no vehicle movement. 9. Repeat steps 7 and 8 with automatic transmission in drive or manual transmission in first gear. 10. Turn the engine off and ...

  • Page 551

    3. Reconnect the negative battery cable. 4. Turn the ignition switch to the lock position. 5. Turn the ignition switch to the on/run position, but do not start the engine. 6. Press and hold the brake pedal. 7. Shift the transmission into neutral. 8. Shift the transfer case lever to the desired posit...

  • Page 553: Contents

    What to do in emergencies contents 䡵 hazard warning flashers . . . . . . . . . . .552 䡵 if your engine overheats . . . . . . . . . . . .552 䡵 wheel and tire torque specifications . . . . . . . . . . . . . . . . . . . . . .553 ▫ torque specifications . . . . . . . . . . . . . . . . . . .553 䡵 jacking...

  • Page 554

    Hazard warning flashers the hazard warning flasher switch is located on the instrument panel below the climate controls. Press the switch to turn on the hazard warning flasher. When the switch is activated, all direc- tional turn signals will flash on and off to warn oncoming traffic of an emergency...

  • Page 555

    Note: there are steps that you can take to slow down an impending overheat condition: • if your air conditioner (a/c) is on, turn it off. The a/c system adds heat to the engine cooling system and turning the a/c off can help remove this heat. • you can also turn the temperature control to maximum he...

  • Page 556

    Tighten the lug nuts/bolts in a star pattern until each nut/bolt has been tightened twice. After 25 miles (40 km) check the lug nut/bolt torque to be sure that all the lug nuts/bolts are properly seated against the wheel. Wheel mounting surface torque patterns 554 what to do in emergencies.

  • Page 557

    Warning! To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts fully until the vehicle has been lowered. Failure to follow this warning may result in personal injury. Jacking and tire changing warning! • do not attempt to change a tire on the side of the vehicle close to...

  • Page 558

    Jack location the jack and lug wrench are located in the rear storage compartment. Note: turn the black plastic wing nut counterclockwise to loosen the jack from the storage bin. Spare tire removal to remove the spare tire from the carrier, remove the tire cover, if equipped, and remove the lug nuts...

  • Page 559

    Note: if you have added aftermarket accessories to the spare tire mounted carrier, it cannot exceed a gross weight of 50 lbs (23 kg) including the weight of the spare tire. Preparations for jacking 1. Park on a firm, level surface. Avoid ice or slippery areas. Warning! Do not attempt to change a tir...

  • Page 560

    Jacking instructions warning! Carefully follow these tire changing warnings to help prevent personal injury or damage to your vehicle: • always park on a firm, level surface as far from the edge of the roadway as possible before raising the vehicle. • turn on the hazard warning flasher. • block the ...

  • Page 561

    Caution! Do not attempt to raise the vehicle by jacking on locations other than those indicated in the jacking instructions for this vehicle. 1. Remove the spare tire, jack and tools from the stored location. 2. Loosen (but do not remove) the wheel lug nuts by turning them to the left one turn while...

  • Page 562

    5. Raise the vehicle by turning the jack screw clockwise. Raise the vehicle only until the tire just clears the surface and enough clearance is obtained to install the spare tire. Minimum tire lift provides maximum sta- bility. Rear jacking location front jacking location 560 what to do in emergenci...

  • Page 563

    Warning! Raising the vehicle higher than necessary can make the vehicle less stable and cause a collision. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. 6. Remove the lug nuts and wheel. 7. Position the spare wheel/tire on the vehicle and inst...

  • Page 564

    Road tire installation 1. Mount the road tire on the axle. 2. Install the remaining lug nuts with the cone shaped end of the nut toward the wheel. Lightly tighten the lug nuts. Warning! To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts fully until the vehicle has bee...

  • Page 565

    Note: when using a portable battery booster pack follow the manufacturer’s operating instructions and precautions. Caution! Do not use a portable battery booster pack or any other booster source with a system voltage greater than 12 volts or damage to the battery, starter motor, alternator or electr...

  • Page 566

    Warning! • take care to avoid the radiator cooling fan when- ever the hood is raised. It can start anytime the ignition switch is on. You can be injured by moving fan blades. • remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact. You co...

  • Page 567

    Caution! Failure to follow these procedures could result in damage to the charging system of the booster vehicle or the discharged vehicle. Connecting the jumper cables 1. Connect the positive (+) end of the jumper cable to the positive (+) post of the discharged vehicle. 2. Connect the opposite end...

  • Page 568

    6. Once the engine is started, remove the jumper cables in the reverse sequence: disconnecting the jumper cables 1. Disconnect the negative (-) jumper cable from the engine ground of the vehicle with the discharged battery. 2. Disconnect the negative end (-) of the jumper cable from the negative (-)...

  • Page 569

    Caution! Racing the engine or spinning the wheels may lead to transmission overheating and failure. Allow the en- gine to idle with the transmission in neutral for at least one minute after every five rocking-motion cycles. This will minimize overheating and reduce the risk of transmission failure d...

  • Page 570

    Warning! (continued) explode and injure someone. Do not spin your vehi- cle’s wheels faster than 30 mph (48 km/h) or for longer than 30 seconds continuously without stop- ping when you are stuck and do not let anyone near a spinning wheel, no matter what the speed. Emergency tow hooks — if equipped ...

  • Page 571

    Shift lever override if a malfunction occurs and the shift lever cannot be moved out of the park position, you can use the following procedure to temporarily move the shift lever: 1. Turn the engine off. 2. Firmly apply the parking brake. 3. Using a small screwdriver or similar tool, remove the shif...

  • Page 572

    7. Move the shift lever to the neutral position. 8. The vehicle may then be started in neutral. 9. Reinstall the shift lever override access cover. Towing a disabled vehicle this section describes procedures for towing a disabled vehicle using a commercial wrecker service. If the trans- mission and ...

  • Page 573

    Proper towing or lifting equipment is required to prevent damage to your vehicle. Use only tow bars and other equipment designed for this purpose, following equip- ment manufacturer’s instructions. Use of safety chains is mandatory. Attach a tow bar or other towing device to main structural members ...

  • Page 574

    Four–wheel drive models the manufacturer recommends towing with all wheels off the ground. Acceptable methods are to tow the vehicle on a flatbed or with one end of the vehicle raised and the opposite end on a towing dolly. If flatbed equipment is not available and the transfer case is operable, the...

  • Page 575: Maintaining Your Vehicle

    Maintaining your vehicle contents 䡵 engine compartment — 3.6l . . . . . . . . . .575 䡵 onboard diagnostic system — obd ii . .576 ▫ loose fuel filler cap message . . . . . . . . . . . .576 䡵 emissions inspection and maintenance programs . . . . . . . . . . . . . . . . . . . . . . . . . .577 䡵 replace...

  • Page 576

    ▫ clutch hydraulic system (manual transmission) — if equipped . . . . . . . . . . . . . . . . . . . . . . .604 ▫ manual transmission — if equipped . . . . . . .604 ▫ transfer case . . . . . . . . . . . . . . . . . . . . . . . .605 ▫ front/rear axle fluid . . . . . . . . . . . . . . . . . .606 ▫ appe...

  • Page 577

    Engine compartment — 3.6l 1 — integrated power module (fuses) 7 — washer fluid reservoir 2 — battery 8 — engine coolant reservoir 3 — engine oil dipstick 9 — air cleaner filter 4 — automatic transmission dipstick (under engine cover) 10 — coolant pressure cap 5 — engine oil fill 11 — power steering ...

  • Page 578

    Onboard diagnostic system — obd ii your vehicle is equipped with a sophisticated onboard diagnostic system called obd ii. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide ex...

  • Page 579

    The message will appear the next time the vehicle is started. This might indicate a damaged cap. If the prob- lem is detected twice in a row, the system will turn on the mil. Resolving the problem will turn the mil off. Emissions inspection and maintenance programs in some localities, it may be a le...

  • Page 580

    3. Approximately 15 seconds later, one of two things will happen: • the mil will flash for about 10 seconds and then return to being fully illuminated until you turn off the ignition or start the engine. This means that your vehicle’s obd ii system is not ready and you should not proceed to the i/m ...

  • Page 581

    Available which include detailed service information for your vehicle. Refer to these service manuals before attempting any procedure yourself. Note: intentional tampering with emissions control systems may void your warranty and could result in civil penalties being assessed against you. Warning! Y...

  • Page 582

    Caution! (continued) • your vehicle has been built with improved fluids that protect the performance and durability of your vehicle and also allow extended maintenance inter- vals. Do not use chemical flushes in these compo- nents as the chemicals can damage your engine, transmission, power steering...

  • Page 583

    Change engine oil the oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance. Refer to the “maintenance schedule” for further informa- tion. Note: under no circumstances should oil change in- tervals exceed 10,000 miles (16,000 km) or twelve mon...

  • Page 584

    Engine oil viscosity — 3.6l engine mopar® sae 5w-20 engine oil approved to chrysler material standard ms-6395 such as pennzoil®, shell helix® or equivalent. Is recommended for all operating temperatures. This engine oil improves low temperature starting and vehicle fuel economy. The engine oil fille...

  • Page 585

    Station or governmental agency for advice on how and where used oil and oil filters can be safely discarded in your area. Engine oil filter the engine oil filter should be replaced with a new filter at every engine oil change. Engine oil filter selection this manufacturer’s engines have a full-flow ...

  • Page 586

    Maintenance-free battery your vehicle is equipped with a maintenance-free battery. You will never have to add water, nor is periodic main- tenance required. Warning! • battery fluid is a corrosive acid solution and can burn or even blind you. Do not allow battery fluid to contact your eyes, skin, or...

  • Page 587

    Caution! • it is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked positive (+) and negative (-) and are identified on the battery case. Cable clamps should be ...

  • Page 588

    Warning! (continued) • the air conditioning system contains refrigerant under high pressure. To avoid risk of personal injury or damage to the system, adding refrigerant or any repair requiring lines to be disconnected should be done by an experienced technician. Caution! Do not use chemical flushes...

  • Page 589

    2. Push in on the sides of the glove compartment and lower the door. 3. Pivot the glove compartment downward. 4. Disengage the two retaining tabs that secure the two air filter access doors to the hvac housing. 5. Open the two air filter access doors. 6. Remove the two particulate air filters from t...

  • Page 590

    7. Install the a/c air filter with the air filter position indicators pointing in the same direction as removal. Caution! The a/c air filter is identified with an arrow to indicate airflow direction through the filter. Failure to properly install the filter will result in the need to replace it more...

  • Page 591

    Operation of the wipers on dry glass for long periods may cause deterioration of the wiper blades. Always use washer fluid when using the wipers to remove salt or dirt from a dry windshield. Avoid using the wiper blades to remove frost or ice from the windshield. Keep the blade rubber out of contact...

  • Page 592

    Exhaust system the best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system. If you notice a change in the sound of the exhaust system; or if the exhaust fumes can be detected inside the vehicle; or when the underside or rear of the vehicle i...

  • Page 593

    Caution! • the catalytic converter requires the use of un- leaded fuel only. Leaded gasoline will destroy the effectiveness of the catalyst as an emissions control device and may seriously reduce engine perfor- mance and cause serious damage to the engine. • damage to the catalytic converter can res...

  • Page 594

    To minimize the possibility of catalytic converter damage: • do not shut off the engine or interrupt the ignition, when the transmission is in gear and the vehicle is in motion. • do not try to start the engine by pushing or towing the vehicle. • do not idle the engine with any spark plug wires disc...

  • Page 595

    Check the engine cooling system hoses for brittle rubber, cracking, tears, cuts, and tightness of the connection at the coolant recovery bottle and radiator. Inspect the entire system for leaks. With the engine at normal operating temperature (but not running), check the cooling system pressure cap ...

  • Page 596

    Caution! • mixing of engine coolant (antifreeze) other than specified organic additive technology (oat) en- gine coolant (antifreeze), may result in engine damage and may decrease corrosion protection. Organic additive technology (oat) engine cool- ant is different and should not be mixed with hybri...

  • Page 597

    You use the same engine coolant (oat coolant conform- ing to ms-12106) throughout the life of your vehicle. Please review these recommendations for using organic additive technology (oat) engine coolant (antifreeze) that meets the requirements of chrysler material stan- dard ms-12106. When adding en...

  • Page 598

    • mixing engine coolant (antifreeze) types is not recom- mended and can result in cooling system damage. If hoat and oat coolant are mixed in an emergency, have a authorized dealer drain, flush, and refill with oat coolant (conforming to ms-12106) as soon as possible. Cooling system pressure cap the...

  • Page 599

    Disposal of used engine coolant used ethylene glycol-based engine coolant (antifreeze) is a regulated substance requiring proper disposal. Check with your local authorities to determine the disposal rules for your community. To prevent ingestion by ani- mals or children, do not store ethylene glycol...

  • Page 600

    If an examination of your engine compartment shows no evidence of radiator or hose leaks, the vehicle may be safely driven. The vapor will soon dissipate. • do not overfill the coolant expansion bottle. • check the coolant freeze point in the radiator and in the coolant expansion bottle. If engine c...

  • Page 601

    Warning! Riding the brakes can lead to brake failure and possibly a collision. Driving with your foot resting or riding on the brake pedal can result in abnormally high brake temperatures, excessive lining wear, and possible brake damage. You would not have your full braking capacity in an emergency...

  • Page 602

    Warning! (continued) • to avoid contamination from foreign matter or moisture, use only new brake fluid or fluid that has been in a tightly closed container. Keep the master cylinder reservoir cap secured at all times. Brake fluid in a open container absorbs moisture from the air resulting in a lowe...

  • Page 603

    Note: no chemical flushes should be used in any transmission; only the approved lubricant should be used. Caution! Using a transmission fluid other than the manufac- turer’s recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder, and will require more...

  • Page 604

    Of driving. At normal operating temperature, the fluid cannot be held comfortably between the fingertips. Use the following procedure to check the transmission fluid level properly: 1. Park the vehicle on level ground. 2. Remove the engine cover by pulling it up off the mounting studs. 3. Run the en...

  • Page 605

    Note: • the holes in the dipstick will be full of fluid if the actual level is at or above the hole. • if it is necessary to check the transmission below the operating temperature, the fluid level should be between the two cold (lower) holes on the dipstick with the fluid at approximately 80° f (27°...

  • Page 606

    In addition, change the fluid and filter if the fluid becomes contaminated (with water, etc.), or if the trans- mission is disassembled for any reason. Clutch hydraulic system (manual transmission) — if equipped the clutch hydraulic system is fed by a segregated volume of fluid within the brake syst...

  • Page 607

    Transfer case fluid level check the fluid level should be to the bottom edge of the fill hole (a) when the vehicle is in a level position. Adding fluid fluid should be added only at filler hole until fluid begins to run out of the hole. Drain first remove the fill plug (b), then the drain plug (c). ...

  • Page 608

    Front/rear axle fluid for normal service, periodic fluid level checks are not required. When the vehicle is serviced for other reasons the exterior surfaces of the axle assembly should be inspected. If gear oil leakage is suspected inspect the fluid level. Refer to “fluids, lubricants, and genuine p...

  • Page 609

    The following maintenance recommendations will enable you to obtain maximum benefit from the corrosion resistance built into your vehicle. What causes corrosion? Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle. The most common causes are: • road...

  • Page 610

    Caution! • do not use abrasive or strong cleaning materials such as steel wool or scouring powder that will scratch metal and painted surfaces. • use of power washers exceeding 1,200 psi (8 274 kpa) can result in damage or removal of paint and decals. Special care • if you drive on salted or dusty r...

  • Page 611

    Wheel and wheel trim care • all wheels and wheel trim, especially aluminum and chrome plated wheels, should be cleaned regularly with a mild soap and water to prevent corrosion. • to remove heavy soil and/or excessive brake dust, use mopar® wheel cleaner. Note: if your vehicle is equipped with dark ...

  • Page 612

    Warning! Do not use volatile solvents for cleaning purposes. Many are potentially flammable and, if used in closed areas, they may cause respiratory harm. Caution! When installing hanging air fresheners in your ve- hicle, read the installation instructions carefully. Some air fresheners will damage ...

  • Page 613

    Seat belt maintenance do not bleach, dye, or clean the belts with chemical solvents or abrasive cleaners. This will weaken the fabric. Sun damage can also weaken the fabric. If the belts need cleaning, use mopar® total clean, a mild soap solution, or lukewarm water. Do not remove the belts from the ...

  • Page 614

    Washing – use mopar® car wash or equivalent, or mild soap suds, lukewarm water, and a brush with soft bristles. If extra cleaning is required, use mopar® convertible cloth top cleaner or equivalent, or a mild foaming cleaner on the entire top, but support the top from underneath. Rinsing – be sure t...

  • Page 615

    Care of fabric top windows caution! Your vehicle’s fabric top has pliable plastic windows which can be scratched unless special care is taken by following these directions: 1. Never use a dry cloth to remove dust. Instead, use a microfiber towel or soft cotton cloth moistened with cold or warm, clea...

  • Page 616

    The zipper, not just one side. Rinse both zipper halves with fresh water and allow to dry. Aggressively work the mopar® soft top zipper cleaner and lubricant or equivalent into the zipper teeth. If a stuck zipper slide is experienced, work the mopar® soft top zipper cleaner and lubricant or equivale...

  • Page 617

    Warning! (continued) • if a general protection fuse for safety systems (air bag system, braking system), power unit systems (engine system, gearbox system) or steering system blows, contact an authorized dealer. Totally integrated power module the totally integrated power module is located in the en...

  • Page 618

    Cavity cartridge fuse mini fuse description j5 25 amp natural passenger door node j6 40 amp green anti-lock brake system (abs) pump/stability control system j7 30 amp pink anti-lock brake system (abs) valve/stability control system j8 — — j9 40 amp green pzev sec motor/flex fuel j10 30 amp pink head...

  • Page 619

    Cavity cartridge fuse mini fuse description j19 60 amp yellow radiator fan j20 30 amp pink front wiper lo/hi j21 20 amp blue front/rear washer j22 — spare m1 15 amp blue center high-mounted stop light (chmsl)/ switch stop lamp feed m2 20 amp yellow relay trailer lighting (stoplamp) m3 20 amp yellow ...

  • Page 620

    Cavity cartridge fuse mini fuse description m10 15 amp blue ignition off draw – vehicle entertainment sys- tem, satellite digital audio receiver (sdars), dvd, hands-free module, radio, antenna, universal garage door opener, vanity lamp m11 10 amp red (ignition off draw) climate control system, under...

  • Page 621

    Cavity cartridge fuse mini fuse description m16 10 amp red airbag module m17 15 amp blue left tail/license/park lamp m18 15 amp blue right tail/park/run lamp m19 25 amp natural auto shut down (asd #1 and #2) m20 15 amp blue cabin compartment node interior light, switch bank m21 20 amp yellow auto sh...

  • Page 622

    Cavity cartridge fuse mini fuse description m30 15 amp blue wiper motor frt, j1962 diagnostic feed m31 20 amp yellow backup lamps m32 10 amp red airbag controller, tt europe m33 10 amp red powertrain controller m34 10 amp red park assist, climate control system, headlamp wash, compass m35 10 amp red...

  • Page 623

    Caution! • when installing the integrated power module cover, it is important to ensure the cover is properly positioned and fully latched. Failure to do so may allow water to get into the integrated power mod- ule, and possibly result in an electrical system failure. • when replacing a blown fuse, ...

  • Page 624

    Replacement bulbs interior bulbs bulb number automatic transmission indicator lamp 658 heater control lamps (2) 194 rocker switch indicator lamp (rear window de- fogger, and rear wash/ wipe) ** soundbar dome lamp 912 ** bulbs only available from authorized dealer. Exterior bulbs bulb number headlamp...

  • Page 625

    Bulb number backup lamps (2) 3157 license lamp 194 note: numbers refer to commercial bulb types that can be purchased from your local authorized dealer. If a bulb needs to be replaced, visit your authorized dealer or refer to the applicable service manual. Bulb replacement note: lens fogging can occ...

  • Page 626

    8. Pull the bulb from the housing. 9. Push connector locking tab to the unlock position. 10. Remove connector from bulb. 11. Push connector onto new bulb base, and push the connector locking tab to the lock position. Caution! Do not touch the new bulb with your fingers. Oil contamination will severe...

  • Page 627

    Front fog lamp 1. Reach under the vehicle to access the back of the front fog lamp. 2. Disconnect the wire harness connector from the front fog lamp connector receptacle. 3. Firmly grasp the bulb by the two latch features and squeeze them together to unlock the bulb from the back of the front fog la...

  • Page 628

    2. Separate the housing from the body by pushing the lamp inboard while pulling the lamp away from the body. 3. Rotate the appropriate socket 1/4 turn counterclock- wise, then remove it from the housing. 4. Pull the bulb straight from the socket to replace. Center high-mounted stop lamp (chmsl) the ...

  • Page 629

    Fluid capacities u.S. Metric fuel (approximate) — two door models 18.6 gallons 70 liters fuel (approximate) — four door models 22.5 gallons 85 liters engine oil with filter 3.6l engine 6 quarts 5.6 liters cooling system * 3.6l engine (mopar® antifreeze/ engine coolant 10 year/150,000 mile formula or...

  • Page 630

    Fluids, lubricants and genuine parts engine component fluid, lubricant, or genuine part engine coolant we recommend you use mopar® antifreeze/coolant 10 year/150,000 mile formula oat (organic additive technology) or equivalent meeting the requirements of chrysler material standard ms-12106. Engine o...

  • Page 631

    Chassis component fluid, lubricant, or genuine part automatic transmission – if equipped use only atf+4® automatic transmission fluid. Fail- ure to use atf+4® fluid may affect the function or performance of your transmission. We recommend mopar® atf+4® fluid. Manual transmission – if equipped we rec...

  • Page 632

    Component fluid, lubricant, or genuine part axle differential (rear) 226 rbi (model 44) – we recommend you use mopar® gear & axle lubricant (sae 80w-90) (api gl-5) or equivalent. For trailer towing, use mopar® synthetic gear & axle lubricant (sae 75w-140). Models equipped with trac-lok™ require an a...

  • Page 633: Maintenance Schedules

    Maintenance schedules contents 䡵 maintenance schedule . . . . . . . . . . . . .632 ▫ maintenance chart. . . . . . . . . . . . . . . . . . . . .635 8 m a i n t e n a n c e s c h e d u l e s.

  • Page 634

    Maintenance schedule your vehicle is equipped with an automatic oil change indicator system. The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance. Based on engine operation conditions, the oil change indicator message will illuminate. This...

  • Page 635

    “understanding your instrument panel” or under “in- strument cluster description/odometer/trip odom- eter” in “understanding your instrument panel” for further information. Note: under no circumstances should oil change inter- vals exceed 10,000 miles (16,000 km) or twelve months, whichever comes fi...

  • Page 636

    Required maintenance intervals . Refer to the maintenance schedules on the following page for the required maintenance intervals. At every oil change interval as indicated by oil change indicator system: • change oil and filter • rotate the tires. Rotate at the first sign of irregu- lar wear, even i...

  • Page 637

    Maintenance chart refer to the maintenance schedules on the following pages for the required maintenance intervals. Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 ...

  • Page 638

    Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,000 192,000 208,0...

  • Page 639

    Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,000 192,000 208,0...

  • Page 640

    Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,000 192,000 208,0...

  • Page 641

    Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,000 192,000 208,0...

  • Page 642

    Warning! • you can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent me- chanic. • failure to properly inspect and m...

  • Page 643: Contents

    If you need consumer assistance contents 䡵 suggestions for obtaining service for your vehicle . . . . . . . . . . . . . . . . . . . . . . .643 ▫ prepare for the appointment. . . . . . . . . . . . .643 ▫ prepare a list . . . . . . . . . . . . . . . . . . . . . . . .643 ▫ be reasonable with requests ....

  • Page 644

    䡵 department of transportation uniform tire quality grades . . . . . . . . . . . . . . . . .649 ▫ treadwear. . . . . . . . . . . . . . . . . . . . . . . . . . .649 ▫ traction grades . . . . . . . . . . . . . . . . . . . . . . .649 ▫ temperature grades. . . . . . . . . . . . . . . . . . . .650 642 if...

  • Page 645

    Suggestions for obtaining service for your vehicle prepare for the appointment if you are having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty. Discuss additional charges with the service manager....

  • Page 646

    Facilities, factory-trained technicians, special tools, and the latest information to ensure the vehicle is fixed correctly and in a timely manner. This is why you should always talk to an authorized dealer service manager first. Most matters can be re- solved with this process. • if for some reason...

  • Page 647

    In mexico contact: av. Prolongacion paseo de la reforma, 1240 sante fe c.P. 05109 mexico, d. F. In mexico city: 5081-7568 outside mexico city: 1-800-505-1300 customer assistance for the hearing or speech impaired (tdd/tty) to assist customers who have hearing difficulties, the manufacturer has insta...

  • Page 648

    The manufacturer will not stand behind any service contract that is not the manufacturer’s service contract. It is not responsible for any service contract other than the manufacturer’s service contract. If you purchased a ser- vice contract that is not a manufacturer’s service contract, and you req...

  • Page 649

    Mopar® parts mopar® fluids, lubricants, parts, and accessories are available from an authorized dealer. They are recom- mended for your vehicle in order to help keep the vehicle operating at its best. Reporting safety defects in the 50 united states and washington, d.C. If you believe that your vehi...

  • Page 650

    Publication order forms to order the following manuals, you may use either the website or the phone numbers listed below. Visa, mas- tercard, american express, and discover orders are ac- cepted. If you prefer mailing your payment, please call for an order form. Note: a street address is required wh...

  • Page 651

    Call toll free at: • 1–800–890–4038 (u.S.) • 1–800–387–1143 (canada) or visit us on the worldwide web at: • www.Techauthority.Com department of transportation uniform tire quality grades the following tire grading categories were established by the national highway traffic safety administration. The...

  • Page 652

    Warning! The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics. Temperature grades the temperature grades are a (the highest), b, and c, representing the tire’s resistan...

  • Page 653: Index

    Index 10

  • Page 654

    Abs (anti-lock brake system) . . . . . . . . . . . . . . . .305 adding engine coolant (antifreeze) . . . . . . . . . . . .594 adding fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . .521 additives, fuel . . . . . . . . . . . . . . . . . . . . . . . . . . .519 airbag. . . . . . . . . . . ...

  • Page 655

    Adding fluid . . . . . . . . . . . . . . . . . . . . . . . . . .603 fluid and filter changes . . . . . . . . . . . . . . . . . .603 fluid change . . . . . . . . . . . . . . . . . . . . . . . . . .603 fluid level check . . . . . . . . . . . . . . . . . . . . . . .601 fluid type . . . . . . . . . . . ...

  • Page 656

    Changing a flat tire . . . . . . . . . . . . . . . . . . . . . . .555 chart, tire sizing . . . . . . . . . . . . . . . . . . . . . . . . .481 check engine light (malfunction indicator light) . .313 checking your vehicle for safety . . . . . . . . . . . . . .100 checks, safety . . . . . . . . . . . ....

  • Page 657

    Cruise light . . . . . . . . . . . . . . . . . . . . . . . . . . . . .308 cupholders . . . . . . . . . . . . . . . . . . . . . . . . . . . . .187 customer assistance . . . . . . . . . . . . . . . . . . . . . . .643 data recorder, event . . . . . . . . . . . . . . . . . . . . . . .76 daytime running ...

  • Page 658

    Emergency, in case of jacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .555 jump starting . . . . . . . . . . . . . . . . . . . . . . . . . .562 tow hooks . . . . . . . . . . . . . . . . . . . . . . . . . . . .568 emission control system maintenance . . . . . . . . . .577 engine a...

  • Page 659

    Air conditioning . . . . . . . . . . . . . . . . . . . . . . .406 engine oil . . . . . . . . . . . . . . . . . . . . . . . . . . . .583 engine oil disposal . . . . . . . . . . . . . . . . . . . . .582 flashers hazard warning . . . . . . . . . . . . . . . . . . . . . . . .552 turn signal . . . . . . ...

  • Page 660

    Fueling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .521 fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .614 gas cap (fuel filler cap) . . . . . . . . . . . . . . . . . . .521 gasoline, clean air . . . . . . . . . . . . . . . . . . . . . . . .517 gasoline (...

  • Page 661

    Hill descent control . . . . . . . . . . . . . . . . . . . . . . .478 hill descent control indicator . . . . . . . . . . . . . . . .478 hill start assist. . . . . . . . . . . . . . . . . . . . . . . . . . .464 hitches trailer towing . . . . . . . . . . . . . . . . . . . . . . . . .529 hood release ....

  • Page 662

    Lap/shoulder belts. . . . . . . . . . . . . . . . . . . . . . . . .52 latches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .104 lead free gasoline . . . . . . . . . . . . . . . . . . . . . . . .517 leaks, fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . .104 life of tir...

  • Page 663

    Rear servicing . . . . . . . . . . . . . . . . . . . . . . . . .625 rear tail . . . . . . . . . . . . . . . . . . . . . . . . . . . . .625 seat belt reminder . . . . . . . . . . . . . . . . . . . . . .303 security alarm . . . . . . . . . . . . . . . . . . . . . . . . .307 service . . . . . . . . . ....

  • Page 664

    Heated . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .114 outside . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .111 rearview . . . . . . . . . . . . . . . . . . . . . . . . . . . . .111 vanity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .114 modifications/a...

  • Page 665

    Owner’s manual (operator manual) . . . . . . . . . . . . .6 paint care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .606 panic alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27 parking brake. . . . . . . . . . . . . . . . . . . . . . . . . . . .458 passing light . . . ...

  • Page 666

    Remote control door locks . . . . . . . . . . . . . . . . . . . . . . . . . . . .24 starting system . . . . . . . . . . . . . . . . . . . . . . . . .30 remote keyless entry (rke) . . . . . . . . . . . . . . . . . .24 remote sound system (radio) controls . . . . . . . . .390 remote starting system. ....

  • Page 667

    Easy entry . . . . . . . . . . . . . . . . . . . . . . . . . . . .154 fold and tumble rear . . . . . . . . . . . . . . . . . . . .160 heated . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .157 height adjustment . . . . . . . . . . . . . . . . . . . . . .153 rear folding . . . . . . . . ...

  • Page 668

    Automatic transmission . . . . . . . . . . . . . . . . . .415 cold weather . . . . . . . . . . . . . . . . . . . . . . . . . .415 engine block heater . . . . . . . . . . . . . . . . . . . . .418 engine fails to start . . . . . . . . . . . . . . . . . . . . .416 manual transmission . . . . . . . . . ...

  • Page 669

    High speed . . . . . . . . . . . . . . . . . . . . . . . . . . .494 inflation pressures . . . . . . . . . . . . . . . . . . . . . . .492 jacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .555 life of tires . . . . . . . . . . . . . . . . . . . . . . . . . . .500 load capacity . . ....

  • Page 670

    Trailer weight . . . . . . . . . . . . . . . . . . . . . . . . . . . .530 transaxle autostick . . . . . . . . . . . . . . . . . . . . . . . . . . . . .432 transfer case . . . . . . . . . . . . . . . . . . . . . . . . . . . .605 four-wheel-drive operation . . . . . . . . . . . . . . .435 maintenance ...

  • Page 671

    Vehicle identification number (vin) . . . . . . . . . . . . .8 vehicle loading . . . . . . . . . . . . . . . . . . . . . . . . . .488 vehicle modifications/alterations . . . . . . . . . . . . . . .9 vehicle storage . . . . . . . . . . . . . . . . . . . . . . . . . . .405 viscosity, engine oil . . . ...

  • Page 672

    Vehicles sold in canada with respect to any vehicles sold in canada, the name chrysler group llc shall be deemed to be deleted and the name chrysler canada inc. Used in substitution therefore. Driving and alcohol drunken driving is one of the most frequent causes of accidents. Your driving ability c...

  • Page 673

    1283259cv1 14wk741-126-aa grand cherokee chrysler 1" gutter 12/05/2012 15:56:03 grand cherokee chrysler group llc o w n e r ’ s m a n u a l 2014 gr and cher ok ee 14wk741-126-aa second edition printed in u.S.A. 2 0 1 4 grand cherokee chrysler group llc o w n e r ’ s m a n u a l 2014 gr and cher ok e...