1. DL manuals
  2. Jeep
  3. Automobile
  4. 2015 Renegade
  5. Owner's Manual

Jeep 2015 Renegade Owner's Manual

Other manuals for 2015 Renegade: Owner's Manual, User Manual

Summary of 2015 Renegade

  • Page 1

    Renegade o w n e r ’ s m a n u a l 20 15 r enegade 15bu-126-ac third edition rev 2 printed in u.S.A. 2 0 1 5 fca us llc.

  • Page 2

    Vehicles sold in canada with respect to any vehicles sold in canada, the name fca us llc shall be deemed to be deleted and the name fca canada inc. Used in substitution therefore. Driving and alcohol drunken driving is one of the most frequent causes of accidents. Your driving ability can be serious...

  • Page 3

    Table of contents section page 1 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 customer assistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Page 5

    Introduction contents 䡵 introduction . . . . . . . . . . . . . . . . . . . . . . . .4 䡵 how to use this manual . . . . . . . . . . . . . .5 䡵 warnings and cautions . . . . . . . . . . . . . .7 䡵 vehicle modifications/alterations . . . .7 䡵 rollover warning . . . . . . . . . . . . . . . . . . .7 1.

  • Page 6

    Introduction congratulations on selecting your new fca us llc vehicle. Be assured that it represents precision workman- ship, distinctive styling, and high quality - all essentials that are traditional to our vehicles. This is a specialized utility vehicle. It can go places and perform tasks that co...

  • Page 7

    This owner’s manual has been prepared with the assis- tance of service and engineering specialists to acquaint you with the operation and maintenance of your vehicle. It is supplemented by warranty information, and various customer-oriented documents. Please take the time to read these publications ...

  • Page 8

    6 introduction.

  • Page 9

    Warnings and cautions this owner’s manual contains warnings against operating procedures that could result in a collision or bodily injury. It also contains cautions against proce- dures that could result in damage to your vehicle. If you do not read this entire owner’s manual, you may miss importan...

  • Page 10

    Do not attempt sharp turns, abrupt maneuvers, or other unsafe driving actions that can cause loss of vehicle control. Failure to operate this vehicle safely may result in a collision, rollover of the vehicle, and severe or fatal injury. Drive carefully. Failure to use the driver and passenger seat b...

  • Page 11

    Customer assistance contents 䡵 suggestions for obtaining service for your vehicle . . . . . . . . . . . . . . . . . . . .11 ▫ prepare for the appointment . . . . . . . . . . . . .11 ▫ prepare a list . . . . . . . . . . . . . . . . . . . . . . . . .11 ▫ be reasonable with requests . . . . . . . . . ....

  • Page 12

    䡵 department of transportation uniform tire quality grades . . . . . . . . .17 ▫ treadwear . . . . . . . . . . . . . . . . . . . . . . . . . . .17 ▫ traction grades. . . . . . . . . . . . . . . . . . . . . . . .17 ▫ temperature grades . . . . . . . . . . . . . . . . . . . .18 10 customer assistance.

  • Page 13

    Suggestions for obtaining service for your vehicle prepare for the appointment if you are having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty. Discuss additional charges with the service manager....

  • Page 14

    Facilities, factory-trained technicians, special tools, and the latest information to ensure the vehicle is fixed correctly and in a timely manner. This is why you should always talk to an authorized dealer service manager first. Most matters can be re- solved with this process. • if for some reason...

  • Page 15

    In mexico contact av. Prolongacion paseo de la reforma, 1240 sante fe c.P. 05109 mexico, d. F. In mexico city: 5081-7568 outside mexico city: 1-800-505-1300 customer assistance for the hearing or speech impaired (tdd/tty) to assist customers who have hearing difficulties, the manufacturer has instal...

  • Page 16

    The manufacturer will not stand behind any service contract that is not the manufacturer’s service contract. It is not responsible for any service contract other than the manufacturer’s service contract. If you purchased a ser- vice contract that is not a manufacturer’s service contract, and you req...

  • Page 17

    Reporting safety defects in the 50 united states and washington, d.C. If you believe that your vehicle has a defect that could cause a crash or cause injury or death, you should immediately inform the national highway traffic safety administration (nhtsa) in addition to notifying the manufacturer. I...

  • Page 18

    Note: a street address is required when ordering manuals (no p.O. Boxes). Service manuals these comprehensive service manuals provide the infor- mation that students and professional technicians need in diagnosing/troubleshooting, problem solving, maintain- ing, servicing, and repairing fca us llc v...

  • Page 19

    Department of transportation uniform tire quality grades the following tire grading categories were established by the national highway traffic safety administration. The specific grade rating assigned by the tire’s manufacturer in each category is shown on the sidewall of the tires on your vehicle....

  • Page 20

    Temperature grades the temperature grades are a (the highest), b, and c, representing the tire’s resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the mater...

  • Page 21

    Graphical table of contents contents 䡵 front view . . . . . . . . . . . . . . . . . . . . . . . . . .20 ▫ front view (trailhawk) . . . . . . . . . . . . . . . . . .21 䡵 rear view . . . . . . . . . . . . . . . . . . . . . . . . . . .22 ▫ rear view (trailhawk) . . . . . . . . . . . . . . . . . . .23 䡵...

  • Page 22

    Front view front view 1 — headlights 2 — engine compartment 3 — windshield 4 — doors 5 — exterior mirrors 6 — wheels 20 graphical table of contents.

  • Page 23

    Front view (trailhawk) front view (trailhawk) 1 — headlights 2 — engine compartment 3 — windshield 4 — doors 5 — exterior mirrors 6 — wheels 3 graphical table of contents 21.

  • Page 24

    Rear view rear view 1 — rear lights 2 — rear windshield wiper 3 — liftgate 22 graphical table of contents.

  • Page 25

    Rear view (trailhawk) rear view (trailhawk) 1 — rear lights 2 — rear windshield wiper 3 — liftgate 3 graphical table of contents 23.

  • Page 26

    Instrument panel instrument panel 1 — headlight switch 2 — air vents 3 — instrument cluster 4 — multifunction lever 5 — windshield wiper lever 6 — air vents 7 — hand grip 8 — glove compartment 9 — steering wheel 24 graphical table of contents.

  • Page 27

    Interior interior features 1 — seats 2 — power window switches 3 — transmission shift lever (automatic/manual options) 4 — selec terrain™ mode knob — if equipped 5 — climate controls 6 — switch panel 7 — uconnect® radio 3 graphical table of contents 25.

  • Page 29

    Getting to know your vehicle contents 䡵 keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 ▫ key fob with remote control . . . . . . . . . . . . .31 䡵 ignition switch . . . . . . . . . . . . . . . . . . . . .41 ▫ operation . . . . . . . . . . . . . . . . . . . . . . . . . . . .41...

  • Page 30

    ▫ to arm the system . . . . . . . . . . . . . . . . . . . .51 ▫ to disarm the system . . . . . . . . . . . . . . . . . . .52 ▫ disabling . . . . . . . . . . . . . . . . . . . . . . . . . . . .53 䡵 doors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53 ▫ manual door locks . . . . . . . ....

  • Page 31

    ▫ rear cross path (rcp) . . . . . . . . . . . . . . . . . .93 ▫ mode of operation . . . . . . . . . . . . . . . . . . . . .94 ▫ blind spot monitoring fault warnings . . . . . . .95 ▫ general information . . . . . . . . . . . . . . . . . . . .96 䡵 exterior lights . . . . . . . . . . . . . . . . . . ....

  • Page 32

    ▫ air outlet and diffuser locations — passenger compartment . . . . . . . . . . . . . . . . .116 ▫ manual climate controls — if equipped . . . . .117 ▫ automatic climate controls — if equipped . .122 䡵 mysky sun roof — if equipped . . . . . . . .135 ▫ removable roof — if equipped . . . . . . . . . ....

  • Page 33

    Keys your vehicle uses either a key start ignition system or keyless ignition system. The key start ignition system consists of a key fob with a remote keyless entry (rke) transmitter and an ignition node module (ignm). The keyless ignition system consists of a key fob with remote keyless entry (rke...

  • Page 34

    Vehicles with keyless enter-n-go™ keyless enter-n-go™ key fob keyless enter-n-go™ key fob emergency key release a — emergency key release button b — emergency key 32 getting to know your vehicle.

  • Page 35

    Key fob with remote control and integrated vehicle key the key fob with remote control contains the rke transmitter with an integrated vehicle key. To use the vehicle key, simply push the vehicle key release button. General information this device complies with part 15 of the fcc rules and rss-210 o...

  • Page 36

    2. Closeness to a radio transmitter such as a radio station tower, airport transmitter, and some mobile or cb radios. To unlock the doors and liftgate the driver’s door may be unlocked by inserting the vehicle key into the exterior driver’s door lock cylinder. To unlock all the doors, push the inter...

  • Page 37

    Key fob with remote control and integrated vehicle key if one or more doors are open, or the liftgate is open, the doors will lock. This is signaled by a quick flash of the turn signals. Vehicles with keyless enter-n-go™ if one or more doors are open, or the liftgate is open, the doors will lock. Th...

  • Page 38

    Key fob with remote control 1. Separating rke halves requires screw removal (if equipped) and gently prying the two halves of the rke transmitter apart using a screwdriver or similar tool. Make sure not to damage the seal during re- moval. Integrated vehicle key battery removal a — rke transmitter 3...

  • Page 39

    2. Remove the battery by turning the back cover over (battery facing downward) and tapping it lightly on a solid surface such as a table or similar surface. Then, replace the battery. When replacing the battery, match the + sign on the battery to the + sign on the inside of the battery clip, located...

  • Page 40

    Separating keyless enter-n-go™ transmitter case 1. Remove the emergency key by sliding the mechanical latch on the back of the rke transmitter sideways with your thumb. Then, pull the key out with your other hand. 2. Separating rke halves requires screw removal (if equipped) and gently prying the tw...

  • Page 41

    3. Remove the battery by turning the back cover over (battery facing downward) and tapping it lightly on a solid surface such as a table or similar surface. Then, replace the battery. When replacing the battery, match the + sign on the battery to the + sign on the inside of the battery clip, located...

  • Page 42

    Programming additional transmitters programming key fobs or rke transmitters may be performed at an authorized dealer. Request for additional key fobs note: only key fobs that are programmed to the vehicle electronics can be used to start and operate the vehicle. Once a key fob is programmed to a ve...

  • Page 43

    Ignition switch operation your vehicle uses either a key start ignition system or keyless ignition system. The key start ignition system consists of a key fob with a remote keyless entry (rke) transmitter and an ignition node module (ignm). The keyless ignition system consists of a key fob with remo...

  • Page 44

    • some electrical devices (e.G. Power locks, alarm, etc.) are still available. 2 — mar/run • driving position. • electrical devices are available. 3 — avv/start • start the engine. The ignition switch is provided with a safety mechanism. If the engine fails to start, the ignition should be returned ...

  • Page 45

    Models with keyless enter-n-go™ this feature allows the driver to operate the ignition switch with the push of a button as long as the remote keyless entry (rke) transmitter is in the passenger compartment. The keyless ignition node (kin system) has three oper- ating positions. The three positions a...

  • Page 46

    • some electrical devices (e.G. Central locking, alarm, etc.) are still available. Run • driving position. • all the electrical devices are available. Start • start the engine. Note: the vehicle will not start if the fobik is located inside the cargo area and the liftgate is opened. Warning! • when ...

  • Page 47

    Caution! An unlocked car is an invitation to thieves. Always remove key from the ignition and lock all doors when leaving the vehicle unattended. Note: for further information, refer to ⬙ starting the engine, ⬙ in ⬙ starting and operating. ⬙ remote starting system — if equipped this system uses the ...

  • Page 48

    • remote start cancelled — too cold • remote start cancelled — time expired the message will stay active until the ignition is placed in the mar/run position. How to use remote start all of the following conditions must be met before the engine will remote start: • shift lever in park • doors closed...

  • Page 49

    To enter remote start mode push and release the remote start button on the rke transmitter twice within five sec- onds. The vehicle doors will lock, the turn signals will flash, and the horn will chirp twice. Then, the engine will start, and the vehicle will remain in the remote start mode for a 15-...

  • Page 50

    Note: for vehicles equipped with the keyless enter-n- go™ feature, the message “remote start active — push start button” will display in the electronic vehicle infor- mation center (evic) or the driver information dispay (did) until you push the start button. Remote start comfort systems — if equipp...

  • Page 51

    Operation. Therefore, only key fobs that are pro- grammed to the vehicle can be used to start and operate the vehicle. The system will not allow the engine to crank if an invalid key fob tries to start the engine. After placing the ignition to the on/run position, if there is a problem with the syst...

  • Page 52

    Vehicle security alarm the vehicle security alarm monitors the vehicle doors for unauthorized entry and if the ignition switch is cycled to the on/run position without a valid key. While the vehicle security alarm is armed, interior switches for door locks and liftgate release are disabled. If somet...

  • Page 53

    To arm the system follow these steps to arm the vehicle security alarm: 1. Make sure the vehicles ignition is cycled to the stop/ off position (refer to ⬙ starting the engine ⬙ in ⬙ start- ing and operating ⬙ for further information). • for vehicles equipped with keyless enter-n-go™, make sure the v...

  • Page 54

    3. If any doors are open, close them. Note: • if a second chime is heard after approximately four seconds from arming the alarm, disarm the alarm by pressing the unlock button. Check for the correct closure of doors and liftgate, then reactivate the system by following steps 1 and 2. • if a second c...

  • Page 55

    • when the vehicle security alarm is armed, the interior power door lock switches will not unlock the doors. The vehicle security alarm is designed to protect your vehicle. However, you can create conditions where the system will give you a false alarm. If one of the previ- ously described arming se...

  • Page 56

    To unlock the driver’s door, insert the key blade into the driver exterior door lock cylinder and turn to the left to unlock the driver’s door. Note: the manual lock knob unlocks each individual door separately as well as the liftgate. Warning! • for personal security and safety in the event of a co...

  • Page 57

    Warning! (continued) • do not leave the key fob in or near the vehicle, or in a location accessible to children, and do not leave the ignition of a vehicle equipped with keyless enter-n-go in the run mode. A child could operate power windows, other controls, or move the vehicle. Central lock/unlock ...

  • Page 58

    If you push the power door lock switch while the ignition is in the mar/run position, and any front door is open, the power locks will not operate. This prevents you from accidentally locking the key in the vehicle. Placing the ignition in the stop/off position or closing the door will allow the loc...

  • Page 59

    Note: if “unlock all doors 1st press” is programmed, all doors will unlock when you grab hold of the front driver’s door handle. To select between “unlock driver door 1st press” and “unlock all doors 1st press,” refer to “uconnect® settings” in “multimedia” for further information. To unlock from th...

  • Page 60

    Do not grab the door handle when pushing the door handle lock button. This could unlock the door(s). Note: the passive entry system will not operate if the rke transmitter battery is dead. The vehicle doors can also be locked by using the lock button located on the vehicle’s interior door panel. Pus...

  • Page 61

    Preventing inadvertent locking of passive entry rke transmitter in vehicle (fobik-safe) to minimize the possibility of unintentionally locking a passive entry rke transmitter inside your vehicle, the passive entry system is equipped with an automatic door unlock feature which will function if the ig...

  • Page 62

    To unlock/enter the liftgate the liftgate passive entry unlock feature is built into the electronic liftgate release. With a valid passive entry rke transmitter within 3 ft (1.0 m) of the liftgate, push the electronic liftgate release to open with one fluid motion. Liftgate release/passive entry a —...

  • Page 63

    Note: if “unlock all doors 1st press” is programmed in evic/did, if equipped, all doors will unlock when you push the electronic release. If ⬙ unlock driver door 1st press ⬙ is programmed in uconnect®, the liftgate will unlock when you push the electronic lock/unlock button on the liftgate. For furt...

  • Page 64

    Emergency unlocking driver door if the remote keyless entry (rke) transmitter battery is low or dead, the emergency key can be used to unlock the driver side door lock cylinder. To release the emergency key, proceed as follows: 1. Slide the emergency key release button to the side. 2. Remove the eme...

  • Page 65

    Warning! • never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be severely injured or killed. Children should be warned not to touch the parking brake, brake peda...

  • Page 66

    Ignition device (keyless enter-n-go) this device complies with part 15 of the fcc rules. Operation is subject to the following two conditions: • this device may not cause harmful interference. • this device must accept any interference received, including interference that may cause undesired op- er...

  • Page 67

    Child locks to provide a safer environment for small children riding in the rear seats, the rear doors are equipped with a child-protection door lock system. To use the system, open each rear door, use a flat blade screwdriver (or ignition key) and rotate the dial to the lock or unlock position. Whe...

  • Page 68

    Note: • when the child lock system is engaged, the door can only be opened by using the outside door handle even though the inside door lock is in the unlocked position. • after disengaging the child-protection door lock system, always test the door from the inside to make certain it is in the desir...

  • Page 69

    Warning! (continued) • do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. In a collision, people riding in these areas are more likely to be seriously injured or killed. • be sure everyone in your vehicle is in a seat and using a seat belt properl...

  • Page 70

    Manual front seat forward/rearward adjustment on models equipped with manual seats, the adjusting bar is located at the front of the seats, near the floor. While sitting in the seat, lift up on the bar and move the seat forward or rearward. Release the bar once you have reached the desired position....

  • Page 71

    Power adjustment (front) — if equipped the power seat controls are located on the outboard side of the seat, close to the floor. Use the switch to move the seat up/down, forward/ rearward, tilt if equipped and to set the angle of the seatback. Power seat switches 1 — power seat switch 2 — power recl...

  • Page 72

    Forward or rearward adjustment the seat can be adjusted both forward and rearward. Push the seat switch forward or rearward, the seat will move in the direction of the switch. Release the switch when the desired position has been reached. Height adjustment the height of the seats can be adjusted up ...

  • Page 73

    • push the heated seat button a second time to turn the lo setting on. • push the heated seat button a third time to turn the heating elements off. If the hi-level setting is selected, the system will auto- matically switch to lo-level after approximately 145 minutes of continuous operation. At that...

  • Page 74

    Rear seats the split rear seat increases the storage of the rear cargo area. Note: • prior to folding the rear seat down, it may be necessary to position the front seat to its mid-track position. Be sure that the front seats are fully upright and posi- tioned forward, this will allow the rear seat t...

  • Page 75

    Removing shelf — if equipped proceed as follows: 1. Disconnect the two links that support the shelf at the eyelets. Rear shelf support links 1 — links 2 — eyelets 4 getting to know your vehicle 73.

  • Page 76

    2. Lift the rear part of the overhead luggage shelf. 3. Clear the pins placed outside of the shelf, and then remove the rear shelf pulling it upwards. 4. The rear shelf can be stored in the cargo area, or behind the front seatbacks. Adjusting the rear shelf 74 getting to know your vehicle.

  • Page 77

    Partial enlargement of cargo area enlargement of the left side of the cargo area allows you to carry a single passenger on the right side of the rear seat, while the enlargement of the right side allows you to carry two passengers. Proceed as follows: 1. Remove the rear shelf (if equipped). 2. Fully...

  • Page 78

    4. Pull the seatback release lever to fold the left or right rear seatback completely forward. Cargo area enlargement folding both sides of the rear seat provides additional storage in the rear cargo area. Proceed as follows: 1. Fully lower the rear seat head restraints. 2. Move the safety belts to ...

  • Page 79

    2. Lift the seatbacks, pushing them back until they lock on both the latches. Verify the red notches are no longer visible on the release lever. If the red notches are visible, the seatback is not secure. Unfolding the rear armrest 40/20/40 tilt the head restraint forward and pull the rear armrest t...

  • Page 80

    The center part of the rear seat can also be used as rear armrest with cupholders. Warning! Be certain that the seatback is securely locked into position. If the seatback is not securely locked into position the seat will not provide the proper stability for child seats and/or passengers. An imprope...

  • Page 81

    Warning! The head restraints for all occupants must be prop- erly adjusted prior to operating the vehicle or occu- pying a seat. Head restraints should never be ad- justed while the vehicle is in motion. Driving a vehicle with the head restraints improperly adjusted or removed could cause serious in...

  • Page 82

    Warning! The head restraints for all occupants must be prop- erly adjusted prior to operating the vehicle or occu- pying a seat. Head restraints should never be ad- justed while the vehicle is in motion. Driving a vehicle with the head restraints improperly adjusted or removed could cause serious in...

  • Page 83

    Note: the head restraints should only be removed by qualified technicians, for service purposes only. If either of the head restraints require removal, see your autho- rized dealer. Steering wheel tilt/telescoping steering column this feature allows you to tilt the steering column upward or downward...

  • Page 84

    To lock the steering column in position, pull the tilt/ telescoping lever upward until fully engaged. Warning! Do not adjust the steering column while driving. Adjusting the steering column while driving or driv- ing with the steering column unlocked, could cause the driver to lose control of the ve...

  • Page 85

    Mirrors inside day/night mirror the mirror can be adjusted up, down, left, and right. The mirror should be adjusted to center on the view through the rear window. Headlight glare from vehicles behind you can be reduced by moving the lever under the mirror to the night position (toward the rear of th...

  • Page 86

    Auto dimming mirror — if equipped this mirror automatically adjusts for headlight glare from vehicles behind you. You can turn the feature on or off by pushing the button at the base of the mirror. A light to the left of the button will illuminate to indicate when the dimming feature is activated. T...

  • Page 87

    Outside mirrors power adjustment mirrors — if equipped the power mirror switch is located on the drivers door panel. To adjust the mirror, push the mirror adjustment switch in the four directions indicated by arrows. Note: • to adjust the power mirrors, the ignition must be in the mar/run position. ...

  • Page 88

    Manual adjustment mirrors — if equipped to adjust the exterior mirrors, push the corners of the mirrors till desired alignment is obtained. Folding mirror the exterior mirrors are hinged to allow the mirror to pivot forward or rearward to help avoid damage. The mirror has three detent positions: ful...

  • Page 89

    Heated mirrors — if equipped these mirrors are heated to melt frost or ice. This feature can be activated whenever you turn on the rear window defroster. Blind spot monitoring (bsm) — if equipped the blind spot monitoring (bsm) system uses two radar- based sensors, located inside the rear bumper fas...

  • Page 90

    The bsm detection zone covers approximately one lane width on both sides of the vehicle, 10 ft (3 m). The zone length starts at the outside mirror and extends approxi- mately 20 ft (6 m) beyond the rear bumper of the vehicle. The bsm system monitors the detection zones on both sides of the vehicle w...

  • Page 91

    The bsm system notifies the driver of objects in the detection zones by illuminating the bsm warning light located in the outside mirrors in addition to sounding an audible (chime) alert and reducing the radio volume. Refer to “modes of operation” for further information. The bsm system monitors the...

  • Page 92

    Entering from the side vehicles that move into your adjacent lanes from either side of the vehicle. Entering from the rear vehicles that come up from behind your vehicle on either side and enter the rear detection zone with a relative speed of less than 31 mph (50 km/h). Side monitoring rear monitor...

  • Page 93

    Overtaking traffic if you pass another vehicle slowly with a relative speed less than 15 mph (25 km/h) and the vehicle remains in the blind spot for approximately 1.5 seconds, the warning light will be illuminated. If the difference in speed between the two vehicles is greater than 15 mph (25 km/h),...

  • Page 94

    The bsm system is designed not to issue an alert on stationary objects such as guardrails, posts, walls, foliage, berms, etc. However, occasionally the system may alert on such objects. This is normal operation and your vehicle does not require service. The bsm system will not alert you of objects t...

  • Page 95

    Warning! The blind spot monitoring system is only an aid to help detect objects in the blind spot zones. The bsm system is not designed to detect pedestrians, bicy- clists, or animals. Even if your vehicle is equipped with the bsm system, always check your vehicles mirrors, glance over your shoulder...

  • Page 96

    Note: in a parking lot situation, oncoming vehicles can be obscured by vehicles parked on either side. If the sensors are blocked by other structures or vehicles, the system will not be able to alert the driver. When rcp is on and the vehicle is in reverse, the driver is alerted using both the visua...

  • Page 97

    Alert present on that side of the vehicle, an audible chime will also be sounded. Whenever a turn signal and de- tected object are present on the same side at the same time, both the visual and audible alerts will be issued. In addition to the audible alert, the radio (if on) will also be muted. Not...

  • Page 98

    System not available in the case of the system being temporary unavailable: • bsm mirror warning lights are turned on continu- ously. • a chime will turn on. • a instrument cluster message will display “blind spot monitoring temporary unavailable.” in the case of the system being completely unavaila...

  • Page 99

    Exterior lights headlights the headlight switch is located on the left side of the instrument panel. The headlight switch controls the operation of the headlights, side marker lights, daytime running lights, fog lights and the dimming of the instru- ment cluster and interior lighting. Turning on the...

  • Page 100

    Automatic lighting — if equipped light sensor the light sensor is equipped with an infrared led, located on the windshield. It detects changes in light intensity outside the vehicle, based on the sensitivity of light set by using the menu on the display or on the uconnect® system. The higher the sen...

  • Page 101

    Front fog lights — if equipped the front fog light switch is built into the headlight switch. To activate the front fog lights, turn on the parking lights or the low beam headlights and push the headlight switch. To turn off the front fog lights, push the headlight switch a second time or turn off t...

  • Page 102

    Headlight delay activation to activate the delay feature, place the ignition in the stop/off position while the headlights are still on. Then, turn off the headlights within two minutes. The delay interval begins when the headlight switch is turned off. Headlight delay disable the feature is disable...

  • Page 103

    Note: the headlights must be on for the high beams to activate. Turn signals move the multifunction lever up or down and the arrows on each side of the instrument cluster flash to show proper operation of the front and rear turn signal lights. • a “turn signal on” message will appear in the instru- ...

  • Page 104

    Interior lights front lights the courtesy light switches is used to turn the courtesy lights on/off. To operate the courtesy lights, push either the drivers or passenger light switch. Courtesy lights 1 — drivers courtesy lights courtesy light switches 1— left switch 2— right switch 102 getting to kn...

  • Page 105

    Note: • before exiting the vehicle, make sure that the interior lights are turned off. This will prevent the battery from discharging once the doors are closed. • if a light is left on it will automatically be turned off after approximately 15 minutes after the ignition is in the stop/off position. ...

  • Page 106

    Vehicles with retractable roof for vehicles equipped with a retractable roof, there are two interior lights located above the grab handles of the rear doors. The lights come on by opening any of the doors. Rear interior light interior light locations 104 getting to know your vehicle.

  • Page 107

    Dome light timing the dome light will automatically illuminate when the doors are unlocked, the doors are opened or after the doors are closed. Timing entering the vehicle the dome lights illuminate in the following ways: • when the doors are unlocked, the dome light will illuminate for approximatel...

  • Page 108

    • the opening of one of the doors (approximately three minutes). • after closing a door (approximately 10 seconds). The dome light timing is disabled when the doors are locked. Cargo area lights two interior lights are located in the cargo area. These lights automatically turn on/off when the liftga...

  • Page 109

    Illuminated vanity mirrors — if equipped an illuminated vanity mirror is located on each sun visor. To use the mirror, rotate the sun visor down and swing the mirror cover upward. The lights will turn on auto- matically. Closing the mirror cover will turn the light off. Vanity mirror 1 — mirror ligh...

  • Page 110

    Interior lights dimmer switch rotate the ambient dimmer control upward or down- ward to increase or decrease the brightness of the ambi- ent light located in the overhead console, door handle lights, lower instrument panel lights, door map pocket lights, and cubby bin lights. With the parking lights...

  • Page 111

    Wipers and washers the windshield wiper/washer controls are located on the lever on the right side of the steering column. The front wipers are operated by rotating a switch, located on the end of the lever. Caution! Always remove any buildup of snow that prevents the windshield wiper blades from re...

  • Page 112

    If the lever is pulled while the wipers are in the off position, the wipers will operate for several wipe cycles, then turn off. Warning! Sudden loss of visibility through the windshield could lead to a collision. You might not see other vehicles or other obstacles. To avoid sudden icing of the wind...

  • Page 113

    If the lever is pushed while the wiper is in the off position, the wiper will operate for several wipe cycles, then turn off. Note: as a protective measure, the pump will stop if the switch is held for more than 30 seconds. Once the lever is released, the pump will resume normal opera- tion. If the ...

  • Page 114

    Windshield wiper de-icer — if equipped your vehicle may be equipped with a windshield wiper de-icer feature that may be activated under the following conditions: • activation by front defrost — the windshield wiper de-icer will be activated automatically in the case of a cold weather manual start wi...

  • Page 115

    There are single window controls on each passenger door trim panel, which operate the passenger door windows. The window controls will operate only when the ignition is in the mar/run or avv/start position. Note: for vehicles equipped with uconnect®, the power window switches will remain active for ...

  • Page 116

    Warning! (continued) windows while operating the power window switches. Such entrapment may result in serious injury or death. Controls auto-down feature — if equipped the driver and passenger power window switches have an auto-down feature. Push the switch for half a second and release it, the wind...

  • Page 117

    • any impact due to rough road conditions may trigger the auto-reverse function unexpectedly during auto- closure. If this happens, pull the switch lightly and hold to close the window manually. Warning! There is no anti-pinch protection when the window is almost closed. Be sure to clear all objects...

  • Page 118

    Climate controls air outlet and diffuser locations — passenger compartment left side air outlets 1 — adjustable air outlet 2 — air vane adjustment 3 — air flow outlet adjustment 4 — fixed air outlet center air outlets 1 — fixed air outlet 2 — air flow outlet adjustment 3 — air vane adjustment 4 — ad...

  • Page 119

    Manual climate controls — if equipped the manual climate controls consist of a series of rotary dials with inner push buttons. Right side air outlets 1 — fixed air outlet 2 — adjustable air outlet 3 — air vane adjustment 4 — air flow outlet adjustment manual temperature controls (mtc) 4 getting to k...

  • Page 120

    1. Blower control rotate this control to regulate the amount of air forced through the ventilation system in any mode. The blower speed increases as you move the control clockwise from the “0” (off) position. 2. Temperature control rotate this control to regulate the temperature of the air inside th...

  • Page 121

    • mix air is directed through the floor, defrost, and side window demister outlets. This setting works best in cold or snowy conditions that require extra heat to the windshield. This setting is good for maintaining comfort while reducing mois- ture on the windshield. • defrost air is directed throu...

  • Page 122

    Note: • continuous use of the recirculation mode may make the inside air stuffy and window fogging may occur. Extended use of this mode is not recommended. • the use of the recirculation mode in cold or damp weather could cause windows to fog on the inside, because of moisture buildup inside the veh...

  • Page 123

    Air recirculation push and release the air recirculation button so that the led is on, to enter recirculation mode. It is recommended to turn the internal air recirculation on while standing in traffic or in tunnels to prevent the introduction of pol- luted air. Do not use the function for a long pe...

  • Page 124

    Automatic climate controls — if equipped 1. Driver temperature control provides the driver with independent temperature con- trol. Rotate the adjustment knob to set desired tempera- ture shown in the temperature display. Rotate fully counter-clockwise for maximum a/c (lo). 2. A/c button push the a/c...

  • Page 125

    4. Blower control indicator leds a total of eight leds illuminate to visually indicate blower speeds. 5. Rear defrost button push the rear defrost button to turn on the rear window defroster and the heated outside mirrors (if equipped). An indicator will illuminate when the rear window defroster is ...

  • Page 126

    9. Sync button push the sync button to toggle the sync feature on/off. The sync indicator will illuminate when this feature is enabled. Sync is used to synchronize the passenger tem- perature setting with the driver temperature setting. Changing the passenger temperature setting while in sync mode w...

  • Page 127

    14. Driver temperature display rotate the driver temperature control dial clockwise or counter-clockwise, to adjust the air temperature in the front left (driver temperature control) zone of the pas- senger compartment. The set temperature is shown on the display. Turning the control knob completely...

  • Page 128

    Automatic control of the functions will be suspended: the system will only override the settings for safety reasons. Manual selections always take priority over automatic ones and are stored until the auto button is pushed or the system itself intervenes for specific safety reasons. The amount of ai...

  • Page 129

    The system operates automatically to adjust the tempera- ture, quantity and distribution of the air introduced into the passenger compartment. It also manages the air recirculation function and the activation of the air condi- tioning compressor. During automatic operation, you can change the set te...

  • Page 130

    Air distribution selection by pushing the mode control buttons (defrost/panel/ floor buttons), it is possible to set one of the seven possible air distributions manually by activating one or more mode buttons: • defrost mode – air flow to the windshield and front side window diffusers to defrost the...

  • Page 131

    When set manually, the air distribution is indicated by the leds on the selected buttons turning on. In combined function mode, functions are enabled to- gether with those already set when the relevant button is pushed. If a button whose function is already active is pushed, the operation is cancell...

  • Page 132

    If the auto button is pushed when the auto led is on, the system changes to manual mode; it displays the current flow and distribution status, which will no longer be managed automatically. If a manual adjustment is made to the air distribution, the a/c button or the blower speed, the led turns off ...

  • Page 133

    In automatic operation, recirculation is managed auto- matically by the system according to outside environ- mental conditions. Note: • use of the recirculation system makes it possible to reach the required heating/cooling conditions faster. It is not recommended to use it on rainy/cold days as it ...

  • Page 134

    Max a/c max a/c sets the system for maximum cooling perfor- mance. Rotate the driver temperature control adjust knob counter-clockwise for max a/c. Both driver and pas- senger temperature displays will show max a/c lo. In max a/c, the blower speed and mode position can be adjusted to desired user se...

  • Page 135

    When the function is activated, the auto button led turns off. With the function activated, the only possible manual adjustments are pushing the a/c control button, adjusting the fan speed and turning the heated rear window off. When the recirculation control or auto buttons are pushed, the climate ...

  • Page 136

    • the a/c compressor is off. • the blower is off. • the heated rear window can be activated/deactivated. Note: the climate control unit stores the temperatures set before the system was turned off and restores them when one of the following knobs/buttons is pushed: • a/c • recirculation • max defros...

  • Page 137

    Mysky sun roof — if equipped removable roof — if equipped the roof consists of front and rear panels that can be removed independently. On some vehicles the front panel can be power operated refer to “power my sky” in this section. My sky retractable roof (closed) my sky retractable roof (open) 4 ge...

  • Page 138

    Caution! The panels are able to withstand the snow. However, it is recommended that you remove excessive layers of snow that have accumulated or damage to the panels may occur. Power my sky — if equipped open/close the front panel the power my sky switches are located on the overhead console. The sw...

  • Page 139

    To retract the front panel to the open position, push the open/close button. From the fully open position, pull the open/close switch: the front panel will close completely. Venting the front panel to vent the front panel push and release the vent switch. During the vent operation any push on the op...

  • Page 140

    Note: with both panels removed the retractable roof cannot be opened or closed. Removing and installing panels note: • remove the panels only when the vehicle is stationary. • the rear panel can be removed only when the front panel is completely closed or removed. Removing panels 1. Front panel must...

  • Page 141

    3. Rotate and keep the key turned to the symbol to release the lock and pull the panel handle down and away from the stowed position, unlocking the panel. Latch key hole rotating supplied key 4 getting to know your vehicle 139.

  • Page 142

    4. Remove the key from the latch key hole. Unlocking panel handle removing key 140 getting to know your vehicle.

  • Page 143

    5. Remove the panel(s). 6. Place the panel(s) inside of the provided bag for storage in the cargo area. Note: an air deflector is available on the jeep accessory line. This deflector has to be used if the front panel is removed, to avoid the “tunnel effect” inside the vehicle. Push panel up removing...

  • Page 144

    Installing panel 1. From outside the vehicle, place the panel(s) on the slides. 2. Gently slide the front panel forward, or the rear panel backwards. 3. Align the colored guide tabs to ensure the panel(s) close properly. Front panel is labeled with yellow guide tabs. Rear panel is labeled with blue ...

  • Page 145

    4. From inside the vehicle, pull the handle down and toward the stowed position, locking it into place. 5. Make sure that the panel has been properly refitted. From inside the passenger compartment, push up- ward on the panel from the bottom, in order to verify that it is properly latched to the cla...

  • Page 146

    Bag for housing panels — if equipped after the panels have been removed, store the roof panels inside of the bag located inside the storage compartment. Note: it is recommended to do this procedure outside of the car. For proper housing, proceed as follows: 1. Open the roof panel bag and lift the pa...

  • Page 147

    2. Place the first panel into the bag, fold the panel dividers and place the second panel into the bag. 3. Close the bag and place it on the inside the cargo area. First panel in storage bag second panel in storage bag 4 getting to know your vehicle 145.

  • Page 148

    4. Open the clips provided in the bag. Anchor them firmly at the tie-down hooks located in the cargo area. Note: • do not load objects that weigh over 165 pounds (75 kg) on top of the roof panel bag. • the bag is washable. Refer to the documentation that is supplied with the bag. Tie-down hook locat...

  • Page 149

    Emergency open/close if the power my sky switch fails, the retractable roof can be operated manually as follows: 1. Remove the protective cap located on the inner lining. 2. Remove the allen key that is supplied in the tool bag in the cargo area. 3. Insert the allen key into the key hole and turn it...

  • Page 150

    Caution! • when refitting panels, be careful to avoid fingers, scarves, ties and items of clothing from getting caught under the panels themselves. • do not open the roof in the presence of snow or ice. There is risk of damage. Hood opening two latches must be released to open the hood. Pull the hoo...

  • Page 151

    Move to the outside of the vehicle and push the safety latch release lever toward the passenger side of the vehicle. The hood release lever is located behind the center front edge of the hood. Remove the support rod from the locking tab and insert it into the seat located on the underside of the hoo...

  • Page 152

    Closing hold up the hood with one hand and with the other hand remove the support rod from its seat and reinsert it into the locking tab. Lower the hood to approximately 6 inches (15 cm) from the engine compartment and drop it. Make sure that the hood is completely closed. Caution! To prevent possib...

  • Page 153

    Warning! Be sure the hood is fully latched before driving your vehicle. If the hood is not fully latched, it could open when the vehicle is in motion and block your vision. Failure to follow this warning could result in serious injury or death. Liftgate opening to unlock the liftgate, use the remote...

  • Page 154

    The liftgate passive entry unlock feature is built into the electronic liftgate release. With a valid passive entry rke transmitter within 3 ft (1.0 m) of the liftgate, push the electronic liftgate release to open with one fluid motion. Electronic liftgate handle location a — electronic liftgate rel...

  • Page 155

    Emergency opening proceed as follows: 1. Remove the rear shelf (if equipped). 2. Fold the rear seats forward. 3. Using the supplied screwdriver (located under cargo floor in tool kit), remove the yellow tab. Emergency opening tab location a — yellow tab 4 getting to know your vehicle 153.

  • Page 156

    4. Insert the screwdriver into the release tab slot to trigger the release tab of the liftgate. Closing grasp the liftgate closing handle and lower the liftgate. Emergency release tab slot location b — release tab slot a — liftgate closing handle 154 getting to know your vehicle.

  • Page 157

    Note: before closing the liftgate, make sure to be in possession of the key because the liftgate will be locked automatically. Cargo area features cargo load floor the vehicle is equipped with a load floor that can be adjusted as needed. Position 1 (floor flush): this position allows you to make the...

  • Page 158

    The load floor provides securing of any cargo inside this position, so that the cargo will slide in the case of sudden braking. Load floor table tilt load supports 1 — loading floor support one 2 — loading floor support two 156 getting to know your vehicle.

  • Page 159

    Access to the loading floor to access the double load compartment, proceed as follows: 1. Lift up on the load floor handle. 2. Place the desired objects inside the compartment. Load floor handle 1 — cargo load floor handle 2 — cargo load floor 4 getting to know your vehicle 157.

  • Page 160

    3. Reposition the load floor. Caution! The load floor must be arranged in a central position with respect to cargo area. Displacement load floor to position the load from the lower to the upper position, proceed as follows: 1. Grasp the load floor handle and lift up the load floor. 2. Correctly plac...

  • Page 161

    Anchoring of the load the cargo tie-downs, located on the cargo area floor, should be used to safely secure loads when the vehicle is moving. The side panels maybe equipped with three hooks (one on the left side and two on the right side) for securing loads that are not excessively heavy. Tie-downs ...

  • Page 162

    Rear power outlet the rear cargo power outlet is located on the left side of the cargo area. The outlet only works when the ignition is in the mar/run position. Load hooks rear 12 volt cargo power outlet 160 getting to know your vehicle.

  • Page 163

    Note: the rear cargo power outlet can be changed to “battery” powered all the time by switching the power outlet integrated power module 20a fuse from fuse location f18 to f30. Refer to “engine compartment controller” in “in case of emergency” for further infor- mation. Caution! Do not connect devic...

  • Page 164

    Rechargeable flashlight — if equipped some vehicle may be equipped with a rechargeable flashlight located in the cargo area. Cargo box — if equipped the cargo area contains a preformed cargo box that can be used for the storage of objects that allows you to obtain a uniform level when loading. Recha...

  • Page 165

    Note: the cargo box is sized for a maximum capacity of distributed weight equal to 242 lbs (110 kg). Internal equipment glove compartment the glove compartment is located on the passengers side of the instrument panel. To open the glove compartment proceed as follows: 1. Unlock the compartment using...

  • Page 166

    Note: • do not insert objects in the glove compartment that will not allow the compartment to fully close. • the glove compartment should be completely closed while the vehicle is in motion. Sun visors sun visors are located on both sides of the rearview mirror. The visors can be lowered or moved to...

  • Page 167

    Extendible sun visor to extend the sun visor, proceed as follows: 1. Place the sun visor against the door glass by detaching it from the hook and turning it toward the side window. 2. Slide the visor. Sliding sun visor 1 — sun visor 4 getting to know your vehicle 165.

  • Page 168

    3. Slide out the sun visor extender. Power outlets the front power outlet is located under the center stack of the instrument panel. It only operates with the ignition in the mar/run position. Models equipped with the optional ⬙ smoker kit, ⬙ will have a cigar lighter instead of the power outlet. Re...

  • Page 169

    Caution! Do not connect devices with power higher than 180 watts (15 amps) to the socket. Do not damage the socket by using unsuitable adaptors. If the 180 watt (15 amp) power rating is exceeded the fuse protect- ing the system will need to be replaced. Warning! To avoid serious injury or death: • o...

  • Page 170

    Power inverter — if equipped there is a 115 volt, 150 watt power inverter outlet located on the back of the center console to convert dc current to ac current. The power inverter can power cellular phones, electronics and other low power devices requir- ing up to 150 watts. Certain high-end video ga...

  • Page 171

    Inverter it will automatically reset. To avoid overloading the circuit, check the power ratings on electrical devices prior to using the power inverter. Warning! To avoid serious injury or death: • do not insert any objects into the receptacles. • do not touch with wet hands. • close the lid when no...

  • Page 172

    Warning! When the cigar lighter is in use it becomes very hot. To avoid serious injury, handle the cigar lighter with care. Always check that the cigar lighter has turned off. Caution! Do not connect devices with power higher than 180 watts (15 amps) to the socket. Do not damage the socket by using ...

  • Page 173

    Front armrest the front armrest is located between the front seats. The armrest can be adjusted by moving it in the direction indicated by the arrows. Push the storage handle and lift up the armrest to access the storage compartment. Front armrest handle storage compartment 4 getting to know your ve...

  • Page 174

    Warning! Do not operate this vehicle with a console compart- ment lid in the open position. Driving with the console compartment lid open may result in injury in a collision. Cupholders there are two cupholders for the front seat passengers, located in the center console. Front cupholders 172 gettin...

  • Page 175

    There are two cupholders located in the rear armrest if equipped. Handle grip the handle grip is located on the passenger side of the instrument panel. The handle can be used to enter or exit the vehicle or when traveling on rough terrain. Rear cupholders handle grip 4 getting to know your vehicle 1...

  • Page 176

    Roof luggage rack — if equipped your vehicle may be equipped with a roof luggage rack for transporting accessories. Crossbars should always be used whenever cargo is placed on the roof luggage rack. Check the straps frequently to be sure that the load remains securely attached. Note: crossbars can b...

  • Page 177

    Warning! Roof rack cargo must be securely tied down before driving your vehicle. Improperly secured loads may fall off the vehicle, particularly at high speeds, re- sulting in personal injury or property damage. Fol- low the roof luggage rack warnings and cautions when carrying cargo on your roof ra...

  • Page 179

    Getting to know your instrument cluster contents 䡵 instrument cluster . . . . . . . . . . . . . . . . .179 ▫ instrument cluster with multi-functional display (evic) . . . . . . . . . . . . . . . . . . . . . . .179 ▫ instrument cluster with reconfigurable multi-functional display (did). . . . . . . ....

  • Page 180

    ▫ mapping and reconfigurable zone display (evic) — if equipped . . . . . . . . . . . . . . . . . .204 ▫ mapping and reconfigurable zone display (did) — (if equipped) . . . . . . . . . . . . . . . . . .206 ▫ oil change reset . . . . . . . . . . . . . . . . . . . . .208 ▫ evic/did control buttons. . ....

  • Page 181

    Instrument cluster instrument cluster with multi-functional display (evic) electronic vehicle information center (evic) cluster a — tachometer b — digital indicator engine coolant temperature warning light with maximum temperature c — multi-functional display d — digital indicator fuel level indicat...

  • Page 182

    Instrument cluster with reconfigurable multi-functional display (did) driver information display (did) cluster a — tachometer b — digital indicator engine coolant temperature c — multi-functional display d — digital indicator fuel level (the triangle symbol pointing toward the right indicates where ...

  • Page 183

    Speedometer (evic) indicates the speed of the vehicle in mph or km/h. Adjusting instrument panel illumination (light sen- sor) inside the speedometer, a light sensor detects ambient light conditions and adjusts the brightness of the instru- ment cluster. Instrument panel light sensor zone a — instru...

  • Page 184

    The instrument works as follows: • in ⬙ day ⬙ mode the display is adjustable on 8 levels, the graphics for the instrument cluster and all indexes are fully illuminated and are not adjustable; • in ⬙ night ⬙ mode the display, the graphics, and the indexes are adjustable on 8 levels. Adjusted accord- ...

  • Page 185

    • in ⬙ night ⬙ mode the display, the graphics, and the indexes are adjustable on 8 levels. Adjusted accord- ingly even the light intensity of the display of the automatic dual zone climate control system and the uconnect system odometer the odometer display shows the total distance the ve- hicle has...

  • Page 186

    Engine coolant temperature gauge the temperature gauge shows engine coolant tempera- ture. Any reading within the normal range indicates that the engine cooling system is operating satisfactorily. The gauge pointer will likely indicate a higher tempera- ture when driving in hot weather, up mountain ...

  • Page 187

    Warning! A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant. You may want to call an authorized dealer for service if your vehicle overheats. If you decide to look under the hood yourself, see “maintaining and caring for your vehicle.” follow th...

  • Page 188

    • unstored messages this message type is displayed indefinitely or until the condition that activated the message is cleared. Examples of this message type are ⬙ turn signal on ⬙ (if a turn signal is left on) and ⬙ lights on ⬙ (if driver leaves the vehicle). • unstored messages until run these messa...

  • Page 189

    Electric park brake (epb) engaged • what does it mean the light comes on with electric park brake (epb) engaged. • what to do switch off the epb and check that the indicator light goes off. If the light remains on, see an authorized dealer. Electronic brake force distribution (ebd) failure • what do...

  • Page 190

    Air bag • what does it mean by placing the ignition switch in mar/ run, the indicator light illuminates but should go out after a few seconds. If the indicator illuminates, this indicates a fail- ure of the air bag system. The dedicated message shows in the display. For more details, refer to ⬙ occu...

  • Page 191

    Seat belt reminder • what does it mean the light comes on as a steady light with the car stopped as a seat belt reminder. • what to do for the permanent deactivation of the horn (buzzer) system s. B. R. (seat belt reminder), contact your authorized dealer. It is possible to reactivate the system thr...

  • Page 192

    Electric park brake failure • what does it mean by placing the ignition in the mar/run position, the light (if equipped) will illumi- nate but should go out after a few seconds. The light comes on when it detects a failure in electric parking brake. The display shows the dedicated message. • what to...

  • Page 193

    Tpms failure • what does it mean each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recom- mended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. (if your vehicle has tires of a different size ...

  • Page 194

    Indicator is illuminated, the system may not be able to detect or signal low tire pressure as intended. Tpms malfunctions may occur for a variety of rea- sons, including the installation of replacement or alternate tires or wheels on the vehicle that prevent the tpms from functioning properly. Alway...

  • Page 195

    Esc system • what does it mean intervention esc system: the light will start to flash as soon as the tires lose traction and the esc system becomes ac- tive. If the “esc activation/malfunction indicator light” begins to flash during ac- celeration, ease up on the accelerator and apply as little thro...

  • Page 196

    Engine malfunction • what does it mean the light is an integral part of the diagnostic system of the vehicle, called obd ii. This system monitors the performance of the emis- sions, engine, and automatic transmission control systems. The light comes on briefly (as a bulb check) when the ignition is ...

  • Page 197

    Park/headlight on indicator • what does it mean the light comes on by activating the park- ing lights or headlights. This feature allows you to maintain the lights for a period of 30, 60, or 90 seconds after placing the ignition in the stop posi- tion. In some conditions, such as the poor quality of...

  • Page 198

    Headlights on • what does it mean the indicator light comes on by turning on the headlights. Cruise set indicator — if equipped • what does it mean this light will turn on when the electronic speed control is set. Symbols displayed in the evic/did oil pressure warning light • what does it mean this ...

  • Page 199

    Charging system light • what does it mean this light shows the status of the electrical charging system. If the light stays on or comes on while driving, turn off some of the vehicle’s non- essential electrical devices or increase engine speed (if at idle). If the charging system light remains on, i...

  • Page 200

    Electronic throttle control (etc) • what does it mean the light will illuminate when the ignition is first placed in the mar/run or avv/ start position and remain on briefly as a bulb check. If the light does not come on during starting, have the system checked by an authorized dealer. If a problem ...

  • Page 201

    Note: • driving with this light illuminated may cause serious damage to the engine. If the overheated oil comes in contact with the engine or exhaust components, a fire may occur. • if the light turns on while driving, stop the vehicle and shut off the engine as soon as possible. Sentry key® / vehic...

  • Page 202

    Forward collision telltale • what does it mean this light will illuminate to warn of a possible collision with the vehicle in front of you. If the light remains on, there may be a fault in the system. • what to do please contact an authorized dealer. Light sensor failure • what does it mean the ligh...

  • Page 203

    The failure could be due to the burning out of the lamp or protection fuse, or the interruption of the electrical connection. • what to do replace the lamp or its fuse. Please contact an autho- rized dealer. Keyless enter-n-go™ system failure • what does it mean the light illuminates in case of fail...

  • Page 204

    Loose fuel filler cap/flapper message indicator • what does it mean this light will illuminate when fuel filler cap is loose. For capless fuel systems, the fuel flapper or the door are not closed properly. • what to do properly close the filler cap. For capless fuel systems, ensure the fuel flapper ...

  • Page 205

    Power steering system warning • what does it mean this light will illuminate to indicate a fail- ure in the electronic power steering system (eps). Although it will still be possible to steer the car, additional effort may be needed to operate the steering wheel. • what to do please contact an autho...

  • Page 206

    Electronic vehicle information center (evic) / driver information display (did) evic/did description the vehicle can be equipped with multifunctional dis- play (evic), or a reconfigurable multifunctional display (did), which offers useful information to the driver. With the ignition in the stop/off ...

  • Page 207

    The display shows the following information, if equipped: • zone (1) – date (centered) – compass (centered) – time (centered) – external temp. (centered) • zone (2) – actual gear indication (centered) – prnd (centered) • zone (3) – date (centered) – compass (centered) – time (centered) – external te...

  • Page 208

    • zone (5) – trip and fuel label (left) – trip and fuel units (left) – trip and fuel value (right) – trip and fuel progress bar (centered) – text (left) • zone (6) – odometer digits (left) – odometer unit (right) – cruise control speed set (center) – speed buzzer (right) • red telltales (left) • amb...

  • Page 209

    • zone (1a) – up and down arrow (left) – title number • zone (1b) – external temp. (centered) – title (centered) – time (centered) • zones (1, 2 & 3) – date – compass – time – external temp. • zone (2) – double scale (centered) • zone (2 & 3) – ignition button info (centered) • zone (4) – speed warn...

  • Page 210

    • zone (9) – prnd (centered) – soft telltale (centered) • zone (10) – hill decent control telltale (centered) • zone (11–12) – telltales (centered) • zone (13) – forward collision telltale (centered) • zone (14) – soft telltale (centered) – cruise control icon (centered) • zone (15) – cruise control...

  • Page 211

    Unless reset, this message will continue to display each time you turn the ignition is cycled to the on/run position. To reset the oil change indicator system (after performing the scheduled maintenance), refer to the following procedure. 1. Without pushing the brake pedal, push the engine start/sto...

  • Page 212

    • up arrow button push and release the up arrow button to scroll upward through the main menu and submenus. • down arrow button push and release the down arrow button to scroll downward through the main menu and submenus. • right arrow button push and release the right arrow button to access the inf...

  • Page 213

    Menu items the menu has the following options: • speedometer • vehicle info • driver assist • fuel consumption • trip • audio • alerts • display setup • vehicle setup speedometer push and release the up or down arrow button until “speedometer” is highlighted in the evic. Push the ok button to change...

  • Page 214

    • transmission temperature display the temperature of the automatic transmission (if equipped). • engine oil temperature view the engine oil temperature. • battery voltage view the voltage value (state of charge) of the battery. Driver assist this menu item allows you to change the settings ( ⬙ no- ...

  • Page 215

    Trip this menu item allows you to view information about the ⬙ trip computer. ⬙ the information displayed, for trip a and for trip b, are: • distance (miles or km) • average consumption (mpg, or l/ 100km or km/l) • travel time (hour/minute) audio this menu item allows you to view the instrument clus...

  • Page 216

    The information that can be displayed is the connection status of the mobile phone (phone connected or discon- nected), the active telephone calls/incoming/on hold, and the management of double calls (first incoming second waiting, etc.). Alerts (messages stored) this menu item allows you to display...

  • Page 217

    • ⴖ full pnrd ⴖ (default): the right side of the display the letters pnrd, the position assumed by the shift lever will be high- lighted in the display. During the operation in sequential mode ( ⬙ autostick ⬙ ), in place of the letter d, the gear will be will be displayed. In the upper-left/top righ...

  • Page 218

    Vehicle setup this menu item allows you to change the settings for the following: • display • units of measure • clock and data • safety • safety and assistance • lights • doors and locks • compass (if equipped) vehicles equipped with multifunctional display reconfigurable: menu items ⬙ display ⬙ (y...

  • Page 219

    ⴖ units of measure ⴖ by selecting the item ⬙ units of measure, ⬙ you can select the unit of measure to use for displaying various magni- tudes. Possible options are: • us • metric • custom ⴖ clock & data ⴖ by selecting the item, ⬙ clock & data ⬙ you can adjust the clock. Possible options are: • set ...

  • Page 220

    ⴖ safety & assistance ⴖ by selecting the item ⬙ safety & assistance, ⬙ you can make the following adjustments: • fcw: a selection of operating modes of the system forward collision warning plus • fcw sensitivity: a selection of the ⬙ readiness ⬙ of intervention of the forward collision warning plus ...

  • Page 221

    • auto park brake (if equipped): enable/disable auto- insertion of the electric parking brake ⴖ lights ⴖ by selecting the item ⬙ lights, ⬙ you can make the follow- ing adjustments: • headlight off delay: set the delay for headlight shut- off after engine shutoff • lights in the opening: activate the...

  • Page 222

    • unlock on first press of key fob (vehicles without passive entry): allows you to choose whether to un- lock all the doors or only the driver’s side door on the first push of the unlock button on the rke • remote door unlock: allows you to open the driver door only on the first push of the unlock b...

  • Page 223

    Note: keep magnetic materials away from the top of the instrument panel, such as ipod’s, mobile phones, lap- tops, and radar detectors. This is where the compass module is located, and it can cause interference with the compass sensor, and it may give false readings. Trip computer the trip computer ...

  • Page 224

    Quantities displayed distance travelled indicates the distance travelled by the start of the new trip. Average consumption represents the average fuel consumption since the start of the new trip. Travel time elapsed time since the start of the new trip. Ok button short push of the button: display of...

  • Page 225

    Safety contents 䡵 brake system . . . . . . . . . . . . . . . . . . . . . . .225 䡵 electronic brake control system . . . .226 ▫ anti-lock brake system (abs) . . . . . . . . . . . .227 ▫ traction control system (tcs) . . . . . . . . . . . .229 ▫ brake assist system (bas) . . . . . . . . . . . . . . .2...

  • Page 226

    䡵 safety tips . . . . . . . . . . . . . . . . . . . . . . . . .299 ▫ transporting passengers . . . . . . . . . . . . . . . . .299 ▫ exhaust gas . . . . . . . . . . . . . . . . . . . . . . . . .300 ▫ safety checks you should make inside the vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Page 227

    Brake system your vehicle is equipped with dual hydraulic brake systems. If either of the two hydraulic systems loses normal capability, the remaining system will still function. However, there will be some loss of overall braking effectiveness. This will be evident by increased pedal travel during ...

  • Page 228

    Electronic brake control system this system enhances directional control and stability of the vehicle under various driving conditions. Esc cor- rects for oversteering or understeering of the vehicle by applying the brake of the appropriate wheel to assist in counteracting the oversteer or understee...

  • Page 229

    Warning! (continued) prevailing road conditions. Esc cannot prevent col- lisions, including those resulting from excessive speed in turns, driving on very slippery surfaces, or hydroplaning. Esc also cannot prevent collisions resulting from loss of vehicle control due to inappro- priate driver input...

  • Page 230

    The abs pump motor runs during the self-test at 12 mph (20 km/h) and during an abs stop. The pump motor makes a low humming noise during operation, which is normal. Warning! • pumping of the anti-lock brakes will diminish their effectiveness and may lead to a collision. Pumping makes the stopping di...

  • Page 231

    • do not “ride” the brakes by resting your foot on the pedal. This could overheat the brakes and result in unpredictable braking action, longer stopping dis- tances, or brake damage. • when descending mountains or hills, repeated braking can cause brake fade with loss of braking control. Avoid repea...

  • Page 232

    Or the “full off” mode. Refer to “electronic stability control (esc)” in this section for further information. Brake assist system (bas) the bas is designed to optimize the vehicle’s braking capability during emergency braking maneuvers. The system detects an emergency braking situation by sens- ing...

  • Page 233

    Electronic roll mitigation (erm) this system anticipates the potential for wheel lift by monitoring the driver’s steering wheel input and the speed of the vehicle. When erm determines that the rate of change of the steering wheel angle and vehicle’s speed are sufficient to potentially cause wheel li...

  • Page 234

    Time expires, the system will release brake pressure and the vehicle will roll down the hill as normal. The system will release brake pressure in proportion to amount of throttle applied. The following conditions must be met in order for hsa to activate: • the vehicle must be stopped. • the vehicle ...

  • Page 235

    Hill descent control (hdc) — if equipped hdc is intended for low speed off road driving while in 4wd low range. Hdc maintains vehicle speed while descending hills during various driving situations. Hdc controls vehicle speed by actively controlling the brakes. Hdc has three states: 1. Off (feature i...

  • Page 236

    Activating hdc once hdc is enabled, it will activate automatically if driven down a grade of sufficient magnitude (greater than approximately 8%). The set speed for hdc is selectable by the driver and can be adjusted using brake and throttle input. Driver override: the driver may override hdc activa...

  • Page 237

    Feedback to the driver: the instrument cluster has an hdc icon and the hdc switch has an led which offer feedback to the driver about the state hdc is in. • the cluster icon and switch lamp will illuminate and remain solid when hdc is enabled or activated. This is the normal operating condition for ...

  • Page 238

    Esc uses sensors in the vehicle to determine the vehicle path intended by the driver and compares it to the actual path of the vehicle. When the actual path does not match the intended path, esc applies the brake of the appro- priate wheel to assist in counteracting the oversteer or understeer condi...

  • Page 239

    Esc operation modes to disable esc and other safety systems, follow the instruction below. There are three modes of active safety systems present on the vehicle: • esc on • partial off • full off esc on – two wheel drive vehicles and four wheel drive vehicles in 2wd and 4wd high range this is the no...

  • Page 240

    Partial off – two wheel drive vehicles and four wheel drive vehicles in 2wd and 4wd high range the “partial off” mode is intended for driving in deep snow, sand, or gravel. This mode raises the threshold for tcs and esc activation, which allows for more wheel spin than what esc normally allows. To e...

  • Page 241

    Warning! • when in “partial off” mode, the tcs functionality of esc, (except for the limited slip feature de- scribed in the tcs section), has been disabled and the “esc off indicator light” will be illuminated. When in “partial off” mode, the engine power reduction feature of tcs is disabled, and t...

  • Page 242

    Note: with the esc switched off, the enhanced vehicle stability offered by esc is unavailable. In an emergency evasive maneuver, the esc system will not engage to assist in maintaining stability. “full off” mode is only intended for off-highway or off-road use. Note: • “full off” is the only operati...

  • Page 243

    Esc activation/malfunction indicator light and esc off indicator light the “esc activation/malfunction indicator light” in the instrument cluster will come on when the ignition switch is turned to the on position. It should go out with the engine running. If the “esc activation/malfunction indicator...

  • Page 244

    • the esc system will make buzzing or clicking sounds when it is active. This is normal; the sounds will stop when esc becomes inactive following the maneuver that caused the esc activation. The ⬙ esc off indicator light ⬙ indicates the electronic stability control (esc) is partially off or full off...

  • Page 245

    Dynamic steering torque (dst) the dst function uses the integration of the esc system with the electric power steering to increase the safety level of the whole car. In critical situations (understeer- ing, oversteering, braking with different grip conditions), through the dst function the esc syste...

  • Page 246

    3. Children that are not big enough to wear the vehicle seat belt properly (refer to ⬙ child restraints ⬙ ) should be secured in a vehicle with a rear seat in child restraints or belt-positioning booster seats. Older chil- dren who do not use child restraints or belt- positioning booster seats shoul...

  • Page 247

    Seat belt systems buckle up even though you are an excellent driver, even on short trips. Someone on the road may be a poor driver and could cause a collision that includes you. This can happen far away from home or on your own street. Research has shown that seat belts save lives, and they can redu...

  • Page 248

    The outboard front passenger seat beltalert is not active when the outboard front passenger seat is unoccupied. Beltalert may be triggered when an animal or heavy object is on the outboard front passenger seat or when the seat is folded flat (if equipped). It is recommended that pets be restrained i...

  • Page 249

    Warning! • relying on the air bags alone could lead to more severe injuries in a collision. The air bags work with your seat belt to restrain you properly. In some collisions, the air bags won’t deploy at all. Always wear your seat belt even though you have air bags. • in a collision, you and your p...

  • Page 250

    Warning! (continued) • a lap belt worn too high can increase the risk of injury in a collision. The seat belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap part of your seat belt as low as possible and keep it snug. • a twisted seat belt may not pro...

  • Page 251

    Warning! (continued) • a frayed or torn seat belt could rip apart in a collision and leave you with no protection. Inspect the seat belt system periodically, checking for cuts, frays, or loose parts. Damaged parts must be re- placed immediately. Do not disassemble or modify the seat belt system. Sea...

  • Page 252

    3. When the seat belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” inserting latch plate into buckle inserting latch plate into buckle 250 safety.

  • Page 253

    4. Position the lap belt so that it is snug and lies low across your hips, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug seat belt reduces the risk of sliding...

  • Page 254

    2. At about 6 to 12 inches (15 to 30 cm) above the latch plate, grasp and twist the seat belt webbing 180 degrees to create a fold that begins immediately above the latch plate. 3. Slide the latch plate upward over the folded webbing. The folded webbing must enter the slot at the top of the latch pl...

  • Page 255

    3. Route the shoulder belt to the inside of the left head restraint. 4. When the seat belt is long enough to fit, insert the mini-latch plate into the mini-buckle until you hear a “click.” 5. Sit back in seat. Slide the regular latch plate up the webbing as far as necessary to allow the seat belt to...

  • Page 256

    10. To disengage the mini-latch from the mini-buckle for storage, insert the regular latch plate into the center red slot on the mini-buckle. The seat belt will auto- matically retract to its stowed position. If necessary, slide the latch plate down the webbing to allow the seat belt to retract full...

  • Page 257

    As a guide, if you are shorter than average, you will prefer the shoulder belt anchorage in a lower position, and if you are taller than average, you will prefer the shoulder belt anchorage in a higher position. After you release the anchorage button, try to move it up or down to make sure that it i...

  • Page 258

    Note: the adjustable upper shoulder belt anchorage is equipped with an easy up feature. This feature allows the shoulder belt anchorage to be adjusted in the upward direction without pushing or squeezing the release but- ton. To verify the shoulder belt anchorage is latched, pull downward on the sho...

  • Page 259

    Energy management feature this vehicle has a seat belt system with an energy management feature in the front seating positions that may help further reduce the risk of injury in the event of a collision. This seat belt system has a retractor assembly that is designed to release webbing in a controll...

  • Page 260

    Sound as the seat belt retracts. Allow the webbing to retract completely in this case and then carefully pull out only the amount of webbing necessary to comfortably wrap around the occupant’s mid-section. Slide the latch plate into the buckle until you hear a ⬙ click. ⬙ in automatic locking mode, t...

  • Page 261

    Mode and activate the vehicle sensitive (emergency) locking mode. Warning! • the seat belt assembly must be replaced if the switchable automatic locking retractor (alr) fea- ture or any other seat belt function is not working properly when checked according to the proce- dures in the service manual....

  • Page 262

    • seat belt pretenioners • seat belt buckle switch • seat track position sensors advanced front air bags this vehicle has advanced front air bags for both the driver and front passenger as a supplement to the seat belt restraint systems. The driver’s advanced front air bag is mounted in the center o...

  • Page 263

    Warning! • being too close to the steering wheel or instrument panel during advanced front air bag deployment could cause serious injury, including death. Air bags need room to inflate. Sit back, comfortably extending your arms to reach the steering wheel or instrument panel. • never place a rear-fa...

  • Page 264

    Advanced front air bag features the advanced front air bag system has multistage driver and front passenger air bags. This system provides output appropriate to the severity and type of collision as determined by the occupant restraint controller (orc), which may receive information from the front i...

  • Page 265

    Warning! (continued) • relying on the air bags alone could lead to more severe injuries in a collision. The air bags work with your seat belt to restrain you properly. In some collisions, air bags won’t deploy at all. Al- ways wear your seat belts even though you have air bags. Advanced front air ba...

  • Page 266

    The steering wheel hub trim cover and the upper right side of the instrument panel separate and fold out of the way as the air bags inflate to their full size. The advanced front air bags fully inflate in less time than it takes to blink your eyes. The air bags then quickly deflate while helping to ...

  • Page 267

    Supplemental side air bags your vehicle is equipped with two types of side air bags: 1. Supplemental seat-mounted side air bags (sabs): located in the outboard side of the front seats. The sabs are marked with a “srs airbag” or “airbag” label sewn into the outboard side of the seats. The sabs may he...

  • Page 268

    When the sab deploys, it opens the seam on the out- board side of the seatback’s trim cover. The inflating sab deploys through the seat seam into the space between the occupant and the door. The sab moves at a very high speed and with such a high force that it could injure occupants if they are not ...

  • Page 269

    The sabics may help reduce the risk of partial or complete ejection of vehicle occupants through side windows in certain rollover or side impact events. Warning! • your vehicle is equipped with left and right supplemental side air bag inflatable curtains (sabics). Do not stack luggage or other cargo...

  • Page 270

    The sabics and sabs (“side air bags”) are designed to activate in certain side impacts and certain rollover events. The occupant restraint controller (“orc”) de- termines whether the deployment of the side air bags in a particular side impact or rollover event is appropriate, based on the severity a...

  • Page 271

    Warning! (continued) properly. In some collisions, side air bags won’t deploy at all. Always wear your seat belt even though you have side air bags. Note: air bag covers may not be obvious in the interior trim, but they will open during air bag deployment. Side impacts in side impacts, the side impa...

  • Page 272

    Air bags is appropriate, the rollover sensing system will also deploy the seat belt pretensioners on both sides of the vehicle. If a deployment occurs the advanced front air bags are designed to deflate immediately after deployment. Note: front and/or side air bags will not deploy in all collisions....

  • Page 273

    Warning! Deployed air bags and seat belt pretensioners cannot protect you in another collision. Have the air bags, seat belt pretensioners, and the seat belt retractor assemblies replaced by an authorized dealer imme- diately. Also, have the occupant restraint controller system serviced as well. Not...

  • Page 274

    System reset procedure depending on the nature of the event the left and right turn signal lights, located in the instrument panel, may both be blinking and will continue to blink until the ignition switch is turned to the off position. After an accident, turn the ignition switch to stop/off positio...

  • Page 275

    Customer action customer will see 8. Turn ignition off. 9. Turn hazard flashers off (manually). System is now reset and the engine may be started. If a reset procedure step is not completed within 60 seconds, then the turn signal lights will turn off and the reset procedure must be performed again i...

  • Page 276

    Diagnostics also record the nature of the malfunction. While the air bag system is designed to be maintenance free, if any of the following occurs, have an authorized dealer service the air bag system immediately. • the air bag warning light does not come on during the four to eight seconds when the...

  • Page 277

    The redundant air bag warning light will stay on until the fault is cleared. In addition, a single chime will sound to alert you that the redundant air bag warning light has come on and a fault has been detected. If the redundant air bag warning light comes on intermit- tently or remains on while dr...

  • Page 278

    Warning! (continued) seat attachment bolts), take the vehicle to your authorized dealer. Only manufacturer approved seat accessories may be used. If it is necessary to modify the air bag system for persons with dis- abilities, contact your authorized dealer. Event data recorder (edr) this vehicle is...

  • Page 279

    In addition to the vehicle manufacturer, other parties, such as law enforcement, that have the special equip- ment, can read the information if they have access to the vehicle or the edr. Child restraints everyone in your vehicle needs to be buckled up at all times, including babies and children. Ev...

  • Page 280

    Before buying any restraint system, make sure that it has a label certifying that it meets all applicable safety standards. You should also make sure that you can install it in the vehicle where you will use it. Note: • for additional information, refer to www.Seatcheck.Org or call 1–866–732–8243. •...

  • Page 281

    Child size, height, weight or age recommended type of child restraint larger children children who have out-grown their forward-facing child restraint, but are too small to properly fit the vehicle’s seat belt belt positioning booster seat and the vehicle seat belt, seated in the rear seat of the ve...

  • Page 282

    Warning! • never place a rear-facing child restraint in front of an air bag. A deploying passenger advanced front air bag can cause death or serious injury to a child 12 years or younger, including a child in a rear- facing child restraint. • only use a rear-facing child restraint in a vehicle with ...

  • Page 283

    Older children and child restraints children who are two years old or who have outgrown their rear-facing convertible child seat can ride forward- facing in the vehicle. Forward-facing child seats and convertible child seats used in the forward-facing direc- tion are for children who are over two ye...

  • Page 284

    Warning! (continued) • when your child restraint is not in use, secure it in the vehicle with the seat belt or latch anchor- ages, or remove it from the vehicle. Do not leave it loose in the vehicle. In a sudden stop or accident, it could strike the occupants or seatbacks and cause serious personal ...

  • Page 285

    Warning! Never allow a child to put the shoulder belt under an arm or behind their back. In a crash, the shoulder belt will not protect a child properly, which may result in serious injury or death. A child must always wear (continued) warning! (continued) both the lap and shoulder portions of the s...

  • Page 286

    Restraint type combined weight of the child + child restraint use any attachment method shown with an “x” below latch – lower anchors only seat belt only latch – lower anchors + top tether anchor seat belt + top tether anchor rear-facing child restraint more than 65 lbs (29.5 kg) x forward-facing ch...

  • Page 287

    Lower anchors and tethers for children (latch) restraint system your vehicle is equipped with the child restraint anchor- age system called latch, which stands for lower anchors and tethers for children. The latch system has three vehicle anchor points for installing latch- equipped child seats. The...

  • Page 288

    Latch positions for installing child restraints in this vehicle • — lower anchorage symbol 2 anchorages per seating position • — top tether anchorage symbol 286 safety.

  • Page 289

    What is the weight limit (child’s weight + weight of the child re- straint) for using the latch an- chorage system to attach the child restraint? 65 lbs (29.5 kg) use the latch anchorage system until the combined weight of the child and the child restraint is 65 lbs (29.5 kg). Use the seat belt and ...

  • Page 290

    Can two child restraints be at- tached using a common lower latch anchorage? No never “share” a latch anchorage with two or more child restraints. If the center position does not have dedicated latch lower anchor- ages, use the seat belt to install a child seat in the center position next to a child...

  • Page 291

    Locating latch anchorages the lower anchorages are round bars that are found at the rear of the seat cushion where it meets the seatback, below the anchorage sym- bols on the seatback. They are just visible when you lean into the rear seat to install the child restraint. You will easily feel them if...

  • Page 292

    Locating tether anchorages there are tether strap anchorages behind each rear seatback, near the floor. Latch-compatible child restraint systems will be equipped with a rigid bar or a flexible strap on each side. Each will have a hook or connector to attach to the lower anchorage and a way to tighte...

  • Page 293

    Center seat latch: warning! • do not install a child restraint in the center posi- tion using the latch system. This position is not approved for installing child seats using the latch attachments. You must use the seat belt and tether anchor to install a child seat in the center seating position. •...

  • Page 294

    3. Attach the lower hooks or connectors of the child restraint to the lower anchorages in the selected seat- ing position. 4. If the child restraint has a tether strap, connect it to the top tether anchorage. See the section “installing child restraints using the top tether anchorage” for direc- tio...

  • Page 295

    Warning! • improper installation of a child restraint to the latch anchorages can lead to failure of the re- straint. The child could be badly injured or killed. Follow the child restraint manufacturer’s directions exactly when installing an infant or child restraint. • child restraint anchorages ar...

  • Page 296

    Lap/shoulder belt systems for installing child restraints in this vehicle • alr = switchable automatic locking retractor • = top tether anchorage symbol 294 safety.

  • Page 297

    What is the weight limit (child’s weight + weight of the child re- straint) for using the tether anchor with the seat belt to attach a for- ward facing child restraint? Weight limit of the child restraint always use the tether anchor when using the seat belt to install a for- ward facing child restr...

  • Page 298

    Installing a child restraint with a switchable automatic locking retractor (alr) 1. Place the child seat in the center of the seating position. For some second row seats, you may need to recline the seat and/or raise the head restraint to get a better fit. If the rear seat can be moved forward and r...

  • Page 299

    Strap. See the section “installing child restraints using the top tether anchorage” for directions to attach a tether anchor. 9. Test that the child restraint is installed tightly by pulling back and forth on the child seat at the belt path. It should not move more than 1 inch (25.4 mm) in any direc...

  • Page 300

    Tether anchorage for that seating position, move the child restraint to another position in the vehicle if one is available. 2. Route the tether strap to provide the most direct path for the strap between the anchor and the child seat. If your vehicle is equipped with adjustable rear head restraints...

  • Page 301

    Warning! (continued) behind the child seat to secure a child restraint top tether strap. • if your vehicle is equipped with a split rear seat, make sure the tether strap does not slip into the opening between the seatbacks as you remove slack in the strap. Transporting pets air bags deploying in the...

  • Page 302

    Exhaust gas warning! Exhaust gases can injure or kill. They contain carbon monoxide (co), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing (co), follow these safety tips: • do not run the engine in a closed garage or in confined...

  • Page 303

    Safety checks you should make inside the vehicle seat belts inspect the seat belt system periodically, checking for cuts, frays, and loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Front seat belt assemblies must be replaced after a collision. Rear s...

  • Page 304

    Warning! Pedals that cannot move freely can cause loss of vehicle control and increase the risk of serious per- sonal injury. • always make sure that floor mats are properly attached to the floor mat fasteners. • never place or install floor mats or other floor coverings in the vehicle that cannot b...

  • Page 305

    Periodic safety checks you should make outside the vehicle tires examine tires for excessive tread wear and uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread or sidewall. Inspect the tread for cuts and cracks. Inspect sidewalls for cuts, cracks, and bulges. C...

  • Page 307

    Starting and operating contents 䡵 starting the engine . . . . . . . . . . . . . . . .309 ▫ tip start feature . . . . . . . . . . . . . . . . . . . . . .310 ▫ if engine fails to start . . . . . . . . . . . . . . . . .310 ▫ cold weather operation . . . . . . . . . . . . . . . .312 ▫ extended park star...

  • Page 308

    ▫ key ignition park interlock. . . . . . . . . . . . . . .337 ▫ brake/transmission shift interlock system. . . .337 䡵 speed control — if equipped . . . . . . . . .338 ▫ activation . . . . . . . . . . . . . . . . . . . . . . . . . . .339 ▫ setting a desired speed . . . . . . . . . . . . . . . . .339 ...

  • Page 309

    ▫ lanesense warning message. . . . . . . . . . . . . .357 ▫ changing lanesense status . . . . . . . . . . . . . .365 䡵 rear park assist — if equipped . . . . . . . .366 ▫ rear park assist sensors . . . . . . . . . . . . . . . .366 ▫ enabling and disabling rear park assist . . . . .368 ▫ service the ...

  • Page 310

    䡵 off-road driving tips . . . . . . . . . . . . . . . .395 ▫ when to use 4wd low range . . . . . . . . . . .395 ▫ driving through water . . . . . . . . . . . . . . . . .395 ▫ driving in snow, mud and sand . . . . . . . . . .397 ▫ hill climbing . . . . . . . . . . . . . . . . . . . . . . . .397 ▫ tra...

  • Page 311

    Starting the engine before starting your vehicle, adjust your seat, adjust the inside and outside mirrors, fasten your seat belt, and if present, instruct all other occupants to buckle their seat belts. Warning! • never leave children alone in a vehicle, or with access to an unlocked vehicle. • allo...

  • Page 312

    4. If the engine does not start, place the ignition in the stop/off position and wait 10-15 seconds before attempting to restart the engine. Automatic transmission proceed as follows: 1. Set the electric park brake (epb) and put the shift lever in the park or neutral position. 2. Press on the brake ...

  • Page 313

    Floor and hold it there. Crank the engine for no more than 15 seconds. This should clear any excess fuel in case the engine is flooded. Leave the ignition key in the mar/ run position, release the accelerator pedal and repeat the “normal starting” procedure. Caution! To prevent damage to the starter...

  • Page 314

    Cold weather operation to ensure reliable starting under extreme cold conditions an externally powered electric block heater (available from your authorized dealer) is required for the 1.4l turbo engine below -20°f (-29°c) and for the 2.4l engine below -29°f (-34°c) and is recommended for the 2.4l e...

  • Page 315

    Caution! To prevent damage to the starter, do not crank con- tinuously for more than 10 seconds at a time. Wait 10 to 15 seconds before trying again. After starting — warming up the engine proceed as follows: • travel slowly, letting the engine run at a reduced rpm, without accelerating suddenly. • ...

  • Page 316

    Vehicles equipped with electronic key (keyless enter- n-go™): to shut off the engine with vehicle speed greater than 5 mph (8 km/h) you must push and hold the ignition or push the start/stop button three times consecutively within a few seconds. The engine will shut down and the ignition will be pla...

  • Page 317

    While cruising, brief full-throttle acceleration within the limits of local traffic laws contributes to a good break-in. Wide-open throttle acceleration in low gear can be detri- mental and should be avoided. The engine oil installed in the engine at the factory is a high-quality energy conserving t...

  • Page 318

    • automatically, by enabling the auto park brake fea- ture in the customer programmable features section of the uconnect® settings or in “safe hold” conditions. To apply the epb manually, pull up on the switch momentarily. You may hear a slight whirring sound from the back of the vehicle while the e...

  • Page 319

    Foot is on the brake pedal, you may notice a small amount of brake pedal movement while the epb is engaging. The electric park brake will be automatically released if the driver’s seat belt is buckled and driver’s intention to start (in forward or reverse direction) is recognized by the system to re...

  • Page 320

    Warning! • never use the park position as a substitute for the parking brake. Always apply the parking brake fully when parked to guard against vehicle move- ment and possible injury or damage. • when leaving the vehicle, always make sure the keyless ignition node is in the stop/off mode, remove the...

  • Page 321

    Caution! If the brake system warning light remains on with the parking brake released, a brake system malfunc- tion is indicated. Have the brake system serviced by an authorized dealer immediately. If exceptional circumstances should make it necessary to engage the epb while the vehicle is in motion...

  • Page 322

    Switch is in the stop/off position. Auto park brake is enabled and disabled by customer selection through the customer programmable features section of the uconnect® settings. Any single auto park brake application can be bypassed by pushing the epb switch to the release position while the transmiss...

  • Page 323

    Safehold can be temporarily bypassed by pushing the epb switch while the driver door is open and the brake pedal is pressed. Once manually bypassed, safehold will be enabled again once the vehicle reaches 12 mph (20 km/h) or the ignition is turned to the stop/off position and back to mar/run again. ...

  • Page 324

    When brake service work is complete, the following steps must be followed to reset the parking brake system to normal operation: • ensure the vehicle is at a standstill. • press the brake pedal with moderate force. • apply the epb switch. Note: a dedicated message will appear in the evic if brake se...

  • Page 325

    To shift the gears, press the clutch pedal to the floor and put the shift lever to the desired position (the diagram for the engagement of the gears is displayed on the handle of the lever). To engage reverse gear from the neutral position lift the reverse ring, located below the knob and simultaneo...

  • Page 326

    Manual transmission shift speeds in mph (km/h) all engines gear selection 2 to 3 3 to 4 4 to 5 5 to 6 accel. 24 (39) 34 (55) 47 (76) 56 (90) cruise 19 (31) 27 (43) 37 (60) 41 (66) downshifting moving from a high gear down to a lower gear is recommended to preserve brakes when driving down steep hill...

  • Page 327

    Caution! (continued) clutch damage, even if the clutch pedal is pressed. If transfer case is in low range the vehicle speeds to cause engine and clutch damage are significantly lower. • failure to follow the maximum recommended downshifting speeds may cause the engine damage and/or damage the clutch...

  • Page 328

    Caution! If you skip a gear while downshifting or downshift at too high of a vehicle speed, these conditions may cause the engine to overspeed if too low of a gear is selected and the clutch pedal is released. Damage to the clutch and the transmission can result from skipping a gear while downshifti...

  • Page 329

    Warning! (continued) you should never exit a vehicle while the engine is running. Before exiting a vehicle, always apply the parking brake, shift the transmission into park, turn the engine stop/off, and remove the key fob. When the ignition is in the stop/off (key removal) position, the transmissio...

  • Page 330

    Caution! (continued) • do not shift between park, reverse, neu- tral, or drive when the engine is above idle speed. • before shifting into any gear, make sure your foot is firmly pressing the brake pedal. Note: you must press and hold the brake pedal while shifting out of park. Shift lever the trans...

  • Page 331

    Into drive or reverse when the vehicle is stopped or moving at low speeds (refer to ⬙ brake/transmission shift interlock system ⬙ in this section for further information). Select the drive range for normal driving. The electronically-controlled transmission provides a precise shift schedule. The tra...

  • Page 332

    Do not race the engine when shifting from park or neutral into another gear range. Caution! After selecting a gear, wait a few second before accelerating. This precaution is especially important with the engine cold. Gear ranges park (p) this range supplements the electric park brake (epb) by lockin...

  • Page 333

    Warning! (continued) • it is dangerous to shift out of park or neutral if the engine speed is higher than idle speed. If your foot is not firmly pressing the brake pedal, the vehicle could accelerate quickly forward or in re- verse. You could lose control of the vehicle and hit someone or something....

  • Page 334

    Caution! • before moving the shift lever out of park, you must turn the ignition switch from the stop/off position to the mar/run position, and also press the brake pedal. Otherwise, damage to the shift lever could result. • do not race the engine when shifting from park or neutral into another gear...

  • Page 335

    Warning! (continued) or road conditions. You might lose control of the vehicle and have a collision. Caution! Towing the vehicle, coasting, or driving for any other reason with the transmission in neutral can cause severe transmission damage. Refer to “recreational towing” in “starting and operating...

  • Page 336

    If the transmission becomes extremely hot, the “trans- mission temperature warning light” may illuminate and the transmission may operate differently until the trans- mission cools down. During cold temperatures, transmission operation may be modified depending on engine and transmission temperature...

  • Page 337

    • the transmission will automatically downshift as the vehicle slows (to prevent engine lugging) and will display the current gear. • the transmission will automatically downshift to first or second gear (depending on model) when coming to a stop. After a stop, the driver should manually upshift (+)...

  • Page 338

    Transmission limp home mode transmission function is electronically monitored for abnormal conditions. If a condition is detected that could result in transmission damage, transmission limp home mode is activated. In this mode, the transmission remains in fourth gear regardless of which forward gear...

  • Page 339

    Key ignition park interlock vehicles equipped with keyless enter-n-go™: this vehicle is equipped with a key ignition park inter- lock which requires the transmission to be in park before the ignition can be turned to the stop/off position. Also, the transmission is locked in park when- ever the igni...

  • Page 340

    Speed control — if equipped when engaged, the electronic speed control takes over accelerator operations at speeds greater than 25 mph (40 km/h). The electronic speed control buttons are located on the right side of the steering wheel. Electronic speed control buttons 1 — on/off 4 — set-/decel 2 — s...

  • Page 341

    Note: • in order to ensure proper operation, the electronic speed control system has been designed to shut down if multiple speed control functions are operated at the same time. If this occurs, the electronic speed control system can be reactivated by pushing the electronic speed control on/off but...

  • Page 342

    When the vehicle has reached the desired speed, push the set (+) or set (-) button and release. Release the accelerator and the vehicle will operate at the selected speed. Deactivation a soft tap on the brake pedal, pushing the cancel button, or normal brake pressure while slowing the vehicle will d...

  • Page 343

    Metric speed (km/h) • pushing the set + button once will result in a 1 km/h increase in set speed. Each subsequent tap of the button results in an increase of 1 km/h. • if the button is continually pushed, the set speed will continue to increase until the button is released, then the new set speed w...

  • Page 344

    Accelerating for passing push the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed. Four wheel drive — jeep active drive (4wd) and jeep active drive low (4wd low) your vehicle may be equipped with a power transfer unit (ptu). This system is auto...

  • Page 345

    Active drive control — if equipped the power transfer unit (ptu) is locked to ensure immediate availability of torque to the rear drive axles. This feature is selectable in auto mode and automatic in the other driving mode. 4wd lock can be enabled by the following ways: • when the 4wd lock button is...

  • Page 346

    The 4wd low mode helps to improve the off-road performance in all modes. To enable 4wd low please follow the steps below: enabling 4wd low with the vehicle stationary, the ignition in the mar/ run or with the engine running, shift the transmission into drive, reverse or neutral and press the button ...

  • Page 347

    • auto : this four-wheel drive operation is a continu- ous operation, is fully automatic and can be used on and off road. This mode balances traction to ensure maneuverability and acceleration improvement com- pared to a car with two wheel drive. This mode also reduces fuel consumption, since it all...

  • Page 348

    • snow : this mode allows you to have greater stability under conditions of bad weather. For use on and off road on surfaces with poor traction, such as roads covered with snow. When in snow mode (depending on certain operating conditions), the transmission may use second gear (rather than first gea...

  • Page 349

    Forward collision warning (fcw) with mitigation — if equipped forward collision warning (fcw) with mitigation operation — if equipped the forward collision warning (fcw) system with mitigation provides the driver with audible warnings, visual warnings (within the evic/did), and may apply a brake jer...

  • Page 350

    Vehicles with a manual transmission : after the end of the intervention of automatic braking, the engine could stall, unless the driver can depress the clutch pedal. Vehicles with automatic transmission : after the end of the intervention of automatic braking, the transmission may remain in last gea...

  • Page 351

    Note: • the minimum speed for fcw activation is 4 mph (7 km/h). • the maximum speed for fcw activation is 124 mph (200 km/h). • the fcw alerts may be triggered on objects other than vehicles such as guard rails or sign posts based on the course prediction. This is expected and is a part of normal fc...

  • Page 352

    • changing the fcw status to “off” deactivates the system, so no warning or active braking will be available in case of a possible collision • changing the fcw status to “only warning” prevents the system from providing limited active braking, or additional brake support if the driver is not braking...

  • Page 353

    A reaction time to the driver lower than the settings ⬙ medium ⬙ and ⬙ far ⬙ , in the case of a potential accident, while a more dynamic driving of the car. The setting of the sensitivity of the system is maintained in memory when the engine is switched off. Fcw limited warning if the evic/did displ...

  • Page 354

    The “fcw front radar sensor temporarily blocked” message can sometimes be displayed while driving in highly reflective areas (i.E. Tunnels with reflective tiles, or ice and snow). The system will recover after the vehicle has left these areas. Under rare conditions, when the radar is not tracking an...

  • Page 355

    The intervention of the system could be unexpected or delayed. The driver must therefore always pay particular attention, while maintaining control of the car to drive in complete safety. Driving in the vicinity of a curve entering or exiting a large curve, the system could detect the presence of a ...

  • Page 356

    Small vehicles and/or not aligned to the lane the system is not able to detect the presence of vehicles that are in front of the car but placed outside the field of action of the radar sensor and could therefore not react in the pres- ence of small vehicles such as bicycles or motorcycles. Lane chan...

  • Page 357

    Passing of vehicles in an oncoming intersection the system could temporarily react to a vehicle that crossed the range of the radar sensor, in an oncoming intersection. General information this vehicle has systems that operate on radio frequency that comply with part 15 of the federal communications...

  • Page 358

    Lanesense — if equipped lanesense operation the lanesense system is operational at speeds above 37 mph (60 km/h) and below 112 mph (180 km/h). The lanesense system uses a forward looking camera to detect lane markings and measure vehicle position within the lane boundaries. When both lane markings a...

  • Page 359

    Turning lanesense on or off the default status of lanesense is “off”. The lanesense button is located on the switch panel below the uconnect® display. To turn the lanesense system on, push the lanesense button (led turns on). A “lane sense on” message is shown in the evic/did. To turn the lanesense ...

  • Page 360

    Left lane departure — only left lane detected • when the lanesense system is on, the lanesense indicator is solid white when only the left lane mark- ing has been detected and the system is ready to provide visual warnings in the evic if an uninten- tional lane departure occurs. • when the lanesense...

  • Page 361

    Left lane departure — both lanes detected • when the lanesense system is on, the lane lines turn from gray to white to indicate that both of the lane markings have been detected. The lanesense indicator is solid green when both lane markings have been detected and the system is “armed” to provide vi...

  • Page 362

    • for example: if approaching the left side of the lane, the steering wheel will turn to the right. • when the lanesense system senses the lane has been approached and is in a lane departure situation, the left thick lane line flashes from white to gray, the left thin line remains solid white and th...

  • Page 363

    • for example: if approaching the left side of the lane, the steering wheel will turn to the right. Note: the lanesense system operates with the similar behavior for a right lane departure. 7.0 did screen — if equipped when the lanesense system is on, the lane lines are gray when both of the lane bo...

  • Page 364

    Left lane departure — only left lane detected • when the lanesense system is on, the lanesense indicator is solid white when only the left lane mark- ing has been detected and the system is ready to provide visual warnings in the did if an unintentional lane departure occurs. • when the lanesense sy...

  • Page 365

    Left lane departure — both lanes detected • when the lanesense system is on, the lane lines turn from gray to white to indicate that both of the lane markings have been detected. The lanesense indicator is solid green when both lane markings have been detected and the system is “armed” to provide vi...

  • Page 366

    • for example: if approaching the left side of the lane the steering wheel will turn to the right. • when the lanesense system senses the lane has been approached and is in a lane departure situation, the left thick lane line flashes yellow (on/off) and the left thin line remains solid yellow. The l...

  • Page 367

    • for example: if approaching the left side of the lane the steering wheel will turn to the right. Note: the lanesense system operates with the similar behavior for a right lane departure. Changing lanesense status the lanesense system has settings to adjust the intensity of the torque warning and t...

  • Page 368

    Rear park assist — if equipped the rear park assist system provides visual and audible indications of the distance between the rear fascia and a detected obstacle when backing up, e.G. During a parking maneuver. Refer to park assist system usage precautions for limitations of this system and recomme...

  • Page 369

    Chime by shifting the vehicle in reverse and in the case of the presence of a rear obstacle, an acoustic signal that varies with the distance of the obstacle from the bumper is activated. The frequency of the acoustic signal: • increases with the distance between car and object decreases. • becomes ...

  • Page 370

    If an obstacle is detected in the left and/or right rear region, the display will show a single flashing arc in the left and/or right rear region and will produce a fast sound tone. As the vehicle moves closer to the obstacle, the display will show the single arc moving closer to the vehicle and the...

  • Page 371

    Caution! After turning off the ignition, the parksense® re- mains in this setting until the next key cycle, even in the case of changing the setting of starting mar/ run to stop/off and then again in mar/run. Service the rear park assist system during vehicle start up, when the rear park assist syst...

  • Page 372

    Park assist system usage precautions note: • ensure that the outer surface and the underside of the rear bumper is clean and clear of snow, ice, mud, dirt or other obstruction to keep the rear park assist system operating properly. • jackhammers, large trucks, and other vibrations could affect the p...

  • Page 373

    Warning! • drivers must be careful when backing up even when using the rear park assist system. Always check carefully behind your vehicle, look behind you, and be sure to check for pedestrians, animals, other vehicles, obstructions, and blind spots before backing up. You are responsible for safety ...

  • Page 374

    Note to “check entire surroundings” across the top of the screen. After five seconds this note will disappear. The camera is located above the rear license plate. When the vehicle is shifted out of reverse (with camera delay turned off), the rear camera mode is exited and the navigation or audio scr...

  • Page 375

    The following table shows the approximate distances for each zone: zone distance to the rear of the vehicle red 0 - 1 ft (0 - 30 cm) yellow 1 ft - 3 ft (30 cm - 1 m) green 3 ft or greater (1 m or greater) note: if snow, ice, mud, or any foreign substance builds up on the camera lens, clean the lens,...

  • Page 376

    Caution! • to avoid vehicle damage, rear back up camera should only be used as a parking aid. The rear back up camera is unable to view every obstacle or object in your drive path. • to avoid vehicle damage, the vehicle must be driven slowly when using the rear back up cam- era to be able to stop in...

  • Page 377

    The tpms will continue to warn the driver of low tire pressure as long as the condition exists, and will not turn off until the tire pressure is at or above the recommended cold placard pressure. Once the low tire pressure warn- ing (tire pressure monitoring telltale light) illuminates, you must inc...

  • Page 378

    Caution! • the tpms has been optimized for the original equipment tires and wheels. Tpms pressures and warning have been established for the tire size equipped on your vehicle. Undesirable system op- eration or sensor damage may result when using replacement equipment that is not of the same size, t...

  • Page 379

    • the tpms is not a substitute for proper tire mainte- nance, and it is the driver’s responsibility to maintain correct tire pressure using an accurate tire pressure gauge, even if underinflation has not reached the level to trigger illumination of the “tire pressure monitor- ing telltale light”. • ...

  • Page 380

    To the vehicle’s recommended cold placard pressure value as shown in the ⬙ inflate to xx ⬙ message. Once the system receives the updated tire pressures, the system will automatically update and the “tire pressure moni- toring telltale light” will turn off. Note: when filling warm tires, the tire pre...

  • Page 381

    Vehicles with compact spare or non-matching full size spare 1. The compact spare tire or non-matching full size spare tire does not have a tire pressure monitoring sensor. Therefore, the tpms will not monitor the pressure in the spare tire. 2. If you install the compact or non-matching full size spa...

  • Page 382

    Note: it is particularly important for you to check the tire pressure in all of the tires on your vehicle monthly and to maintain the proper pressure. The tpms consists of the following components: • receiver module • four tire pressure monitoring sensors • various tire pressure monitoring system me...

  • Page 383

    Should this occur, you should stop as soon as possible and inflate the tires with low pressure (those in a different color in the evic/did graphic) to the vehicle’s recommended cold placard pressure value as shown in the ⬙ inflate to xx ⬙ message. Once the system receives the updated tire pressures,...

  • Page 384

    2. Installing some form of aftermarket window tinting that affects radio wave signals. 3. Lots of snow or ice around the wheels or wheel housings. 4. Using tire chains on the vehicle. 5. Using wheels/tires not equipped with tpms sensors. Vehicles with matching full-size spare 1. The matching full si...

  • Page 385

    Vehicles with compact spare or non-matching full size spare 1. The compact spare tire or non-matching full size does not have a tire pressure monitoring sensor. Therefore, the tpms will not monitor the pressure in the compact spare tire. 2. If you install the compact or non-matching full size spare ...

  • Page 386

    General information this device complies with part 15 of the fcc rules and rss-210 of industry canada. Operation is subject to the following two conditions: (1) this device may not cause harmful interference. (2) this device must accept any interference received, including interference that may caus...

  • Page 387

    Light spark knock at low engine speeds is not harmful to your engine. However, continued heavy spark knock at high speeds can cause damage and immediate service is required. Poor quality gasoline can cause problems such as hard starting, stalling, and hesitations. If you experi- ence these symptoms,...

  • Page 388

    Caution! (continued) emissions to exceed the applicable standard, and/or cause the “malfunction indicator light” to illumi- nate. Please observe pump labels as they should clearly communicate if a fuel contains greater than 10% ethanol. Problems that result from using gasoline containing methanol or...

  • Page 389

    Without mmt be used in your vehicle. The mmt content of gasoline may not be indicated on the gasoline pump, therefore, you should ask your gasoline retailer whether the gasoline contains mmt. Mmt is prohibited in federal and california reformulated gasoline. Materials added to fuel all gasoline sold...

  • Page 390

    Caution! (continued) • the use of fuel additives, which are now being sold as octane enhancers, is not recommended. Most of these products contain high concentrations of methanol. Fuel system damage or vehicle perfor- mance problems resulting from the use of such fuels or additives is not the respon...

  • Page 391

    Warning! (continued) • guard against carbon monoxide with proper main- tenance. Have the exhaust system inspected every time the vehicle is raised. Have any abnormal conditions repaired promptly. Until repaired, drive with all side windows fully open. Adding fuel the capless fuel system uses a flapp...

  • Page 392

    • insert the fuel nozzle in the filler pipe and proceed with filling the fuel tank. • before removing the nozzle, wait at least 10 seconds to allow the fuel to flow inside of the tank. • pull the nozzle from the filler pipe and then close the door. Emergency refueling procedure if the vehicle is out...

  • Page 393

    • open the fuel door. • insert the emergency fuel fill funnel in the filler pipe and proceed to fill the fuel tank. • remove the emergency fuel fill funnel, and close the door. • store the emergency fuel fill funnel in the cargo area. Emergency fuel fill funnel – if equipped with full size spare tir...

  • Page 394

    Warning! • do not to affix objects/plugs to the end of the filler neck other than is provided on the car. • the use of objects/plugs do not comply with the vehicle and may cause pressure increases inside the tank, creating dangerous conditions. • do not approach the neck of the tank with open flames...

  • Page 395

    Payload the payload of a vehicle is defined as the allowable load weight a truck can carry, including the weight of the driver, all passengers, options and cargo. Gross axle weight rating (gawr) the gawr is the maximum permissible load on the front and rear axles. The load must be distributed in the...

  • Page 396

    Loading the actual total weight and the weight of the front and rear of your vehicle at the ground can best be determined by weighing it when it is loaded and ready for operation. The entire vehicle should first be weighed on a commer- cial scale to insure that the gvwr has not been exceeded. The we...

  • Page 397

    On-road driving tips utility vehicles have higher ground clearance and a narrower track to make them capable of performing in a wide variety of off-road applications. Specific design characteristics give them a higher center of gravity than ordinary cars. An advantage of the higher ground clearance ...

  • Page 398

    Caution! When driving through water, do not exceed 5 mph (8 km/h). Always check water depth before entering as a precaution, and check all fluids afterward. Driv- ing through water may cause damage that may not be covered by the new vehicle limited warranty. Driving through water more than a few inc...

  • Page 399

    Driving in snow, mud and sand in heavy snow, when pulling a load, or for additional control at slower speeds, shift the transmission to a low gear and shift the 4wd system to the appropriate terrain mode, using 4wd low if necessary. Refer to “four- wheel drive operation” in “starting and operating” ...

  • Page 400

    If the wheels start to slip as you approach the crest of a hill, ease off the accelerator and maintain headway by turning the front wheels slowly left and right. This may provide a fresh “bite” into the surface and will usually provide traction to complete the climb. Traction downhill shift the tran...

  • Page 401

    • check for accumulations of plants or brush. These things could be a fire hazard. They might hide damage to fuel lines, brake hoses, axle pinion seals, and propeller shafts. • after extended operation in mud, sand, water, or similar dirty conditions, have the radiator, fan, brake rotors, wheels, br...

  • Page 402

    Warning! Continued operation with reduced assist could pose a safety risk to yourself and others. Service should be obtained as soon as possible. If the “service power steering ⬙ or ⬙ power steering assist off - service system” message and a steering wheel icon are displayed on the evic/did screen, ...

  • Page 403

    Trailer towing in this section you will find safety tips and information on limits to the type of towing you can reasonably do with your vehicle. Before towing a trailer, carefully review this information to tow your load as efficiently and safely as possible. To maintain the new vehicle limited war...

  • Page 404

    Gross axle weight rating (gawr) the gawr is the maximum capacity of the front and rear axles. Distribute the load over the front and rear axles evenly. Make sure that you do not exceed either front or rear gawr. Refer to “vehicle loading/vehicle certification la- bel” in “starting and operating” for...

  • Page 405

    Weight-distributing hitch a weight-distributing system works by applying lever- age through spring (load) bars. They are typically used for heavier loads to distribute trailer tongue weight to the tow vehicle’s front axle and the trailer axle(s). When used in accordance with the manufacturer’s direc...

  • Page 406

    Trailer hitch classification the following chart provides the industry standard for the maximum trailer weight a given trailer hitch class can tow and should be used to assist you in selecting the correct trailer hitch for your intended towing condition. Trailer hitch classification definitions clas...

  • Page 407

    Trailer towing weights (maximum trailer weight ratings) the following chart provides the maximum trailer weight ratings towable for your given drivetrain. 1.4l turbo engine trailer towing is not recommended. Engine max. Gtw (gross trailer wt.) max. Tongue wt. (see note) 2.4l 2,000 lbs (900 kg) 200 l...

  • Page 408

    Trailer and tongue weight always load a trailer with 60% to 65% of the weight in the front of the trailer. This places 10% to 15% of the gross trailer weight (gtw) on the tow hitch of your vehicle. Loads balanced over the wheels or heavier in the rear can cause the trailer to sway severely side to s...

  • Page 409

    Note: remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options or dealer-installed options must be considered as part of the total load on your vehicle. Refer to the “tire and loading information” placard for the maximum combine...

  • Page 410

    Warning! (continued) • vehicles with trailers should not be parked on a grade. When parking, apply the parking brake on the tow vehicle. Put the tow vehicle transmission in park. Always, block or ⴖ chock ⴖ the trailer wheels. • gcwr must not be exceeded. • total weight must be distributed between th...

  • Page 411

    • check the trailer tires for proper tire inflation pres- sures before trailer usage. • check for signs of tire wear or visible tire damage before towing a trailer. Refer to “tires – general information” in “starting and operating” for the proper inspection procedure. • when replacing tires, refer t...

  • Page 412

    Warning! (continued) • towing any trailer will increase your stopping distance. When towing you should allow for addi- tional space between your vehicle and the vehicle in front of you. Failure to do so could result in a collision. Caution! If the trailer weighs more than 1,000 lbs (454 kg) loaded, ...

  • Page 413

    Four-pin connector 1 — female pins 4 — park 2 — male pin 5 — left stop/turn 3 — ground 6 — right stop/turn seven-pin connector 1 — battery 5 — ground 2 — backup lamps 6 — left stop/turn 3 — right stop/turn 7 — running lamps 4 — electric brakes 7 starting and operating 411.

  • Page 414

    Towing tips before setting out on a trip, practice turning, stopping, and backing the trailer in an area located away from heavy traffic. Automatic transmission — if equipped the drive range can be selected when towing. The transmission controls include a drive strategy to avoid frequent shifting wh...

  • Page 415

    Electronic speed control — if equipped • do not use in hilly terrain or with heavy loads. • when using the speed control, if you experience speed drops greater than 10 mph (16 km/h), disengage until you can get back to cruising speed. • use speed control in flat terrain and with light loads to maxim...

  • Page 416

    Recreational towing towing this vehicle behind another vehicle front wheel drive (fwd) four-wheel drive (4wd) towing condition wheels off the ground automatic transmission manual transmission manual/ automatic transmission flat tow none not allowed not allowed not allowed dolly tow rear not allowed ...

  • Page 417

    Recreational towing models with front-wheel drive (fwd) recreational towing is allowed only if the front wheels are off the ground. This may be accomplished using a tow dolly (front wheels off the ground) or vehicle trailer (all four wheels off the ground). If using a tow dolly, follow this procedur...

  • Page 418

    Caution! Towing this vehicle with any of its wheels on the ground can cause severe transmission and/or power transfer unit damage. Damage from improper towing is not covered under the new vehicle limited war- ranty. 416 starting and operating.

  • Page 419

    In case of emergency contents 䡵 hazard warning flashers . . . . . . . . . . .419 䡵 assist and 9–1–1 — if equipped . . . . . . . .419 䡵 bulb replacement . . . . . . . . . . . . . . . . . . .424 ▫ general information. . . . . . . . . . . . . . . . . . . .424 ▫ replacement bulbs. . . . . . . . . . . . ...

  • Page 420

    䡵 jump starting . . . . . . . . . . . . . . . . . . . . . .483 ▫ preparations for jump start . . . . . . . . . . . . . .484 ▫ jump starting procedure . . . . . . . . . . . . . . . .485 䡵 enhanced accident response system . . . . . . . . .487 ▫ system reset procedure . . . . . . . . . . . . . . . . ....

  • Page 421

    Hazard warning flashers the hazard warning flasher switch is located on the switch bank below the radio. Push the switch to turn on the hazard warning flasher. When the switch is activated, all direc- tional turn signals will flash on and off to warn oncoming traffic of an emergency. Push the switch...

  • Page 422

    Note: the assist and 9–1–1 features operate through the uconnect® access service. These buttons will only operate as long as your uconnect® access service is active. Refer to your “uconnect® radio supplement” for further information. Assist call the assist button is used to automatically connect you...

  • Page 423

    3. Once a connection between the vehicle and a 9-1-1 operator is made, the 9-1-1 call system may transmit the following important vehicle information to a 9-1-1 operator: • indication that the occupant placed a 9-1-1 call. • the vehicle brand. • the last known gps coordinates of the vehicle. 4. You ...

  • Page 424

    Warning! (continued) • the 9-1-1 call system is embedded into the vehi- cle’s electrical system. Do not add aftermarket electrical equipment to the vehicle’s electrical sys- tem. This may prevent your vehicle from sending a signal to initiate an emergency call. To avoid inter- ference that can cause...

  • Page 425

    Warning! • ignoring the assist and 9-1-1 buttons light could mean you will not have 9-1-1 call services. If the assist and 9-1-1 buttons light is illuminated, have an authorized dealer service the 9-1-1 call system immediately. • the occupant restraint control module turns on the air bag warning lig...

  • Page 426

    Note: never place anything on or near the vehicle’s wireless and gps antennas. You could prevent wireless and gps signal reception, which can prevent your vehicle from placing an emergency call. Wireless and gps signal reception is required for the 9-1-1 call system to function properly. General inf...

  • Page 427

    Replacement bulbs interior bulbs lamps bulb number front courtesy light c5w front courtesy lights (sun visors) c5w rear dome light (models without retractable roof) c5w rear interior lights (models with retractable roof) c5w interior lights w5w dome light (glove box) w5w 8 in case of emergency 425.

  • Page 428

    Exterior bulbs lamps bulb number low beam/high beam headlamps h13 front position/daytime running lights (drl ) p21/5w front direction indicator lamps py21w front fog lamps h11 side indicators (front and side view mirror) wy5w tail/brake lights/turn indicators p21w center high mounted stop lamp (chms...

  • Page 429

    Replacing exterior bulbs headlamps hi/lo beam light halogen to replace the bulbs proceed as follows: 1. Open the engine compartment and remove the head- lamp bulb cap. Headlamp bulb cap 8 in case of emergency 427.

  • Page 430

    2. Rotate the headlamp bulb socket counterclockwise then pull outwards. 3. Push on the locking tab on the headlamp bulb connec- tor and remove the bulb and socket. Headlamp bulb socket headlamp bulb connector 428 in case of emergency.

  • Page 431

    4. Install the new headlamp bulb making sure it is properly locked. 5. Install the headlamp bulb and socket; turn it clockwise making sure it is properly locked. Warning! Carry out the operation of replacing lamps only with the engine off. Also make sure that the engine is cold, to avoid the danger ...

  • Page 432

    Position lights/daytime running lights/fog lights to replace the bulbs proceed as follows: 1. Turn the front wheels completely. 2. Use a suitable tool to remove the access door. Position light/daytime running light/fog light access 1 — screws 2 — access door 430 in case of emergency.

  • Page 433

    3. Remove the electrical connectors. 4. Rotate in a counterclockwise direction (on the left- hand socket) or in a clockwise direction (on the right-hand socket) and remove the bulb and bulb socket. Electrical connectors position light/daytime running light assembly 1 — drl bulb socket 2 — turn signa...

  • Page 434

    5. To replace the bulb gently push bulb and rotate counterclockwise. 6. Insert the new bulb by pushing on it and turning it clockwise. Make sure the bulb is correctly locked in place. 7. Install the bulb and sockets and rotate them clockwise (right side) and clockwise (left side), making sure that i...

  • Page 435

    Front fog lights to replace the bulbs proceed as follows: 1. Turn the front wheels completely. 2. Use a suitable tool to remove the access door. Position light/daytime running light/fog light access 1 — screws 2 — access door 8 in case of emergency 433.

  • Page 436

    3. By pushing the electrical connector tab remove the electrical connector. 4. Rotate the bulb counterclockwise, and then replace the bulb. 5. Insert the new bulb in the socket, making sure the bulb is locked into place. 6. Reconnect the electrical connector. 7. Reinstall the access door. Fog light ...

  • Page 437

    Side indicators front side indicators to replace the bulb proceed as follows: 1. Operating from inside the engine compartment using a suitable tool release the retaining clip. 2. Remove lamp assembly by sliding it toward the out- side. Lamp retaining clip lamp assembly 8 in case of emergency 435.

  • Page 438

    3. Remove the electrical connector by pushing the tab then disconnect the electrical connector. 4. Rotate counterclockwise to release the bulb socket from the lamp assembly, and remove it. Electrical connector bulb socket 436 in case of emergency.

  • Page 439

    5. Remove the bulb from the socket 6. Insert the new bulb in the socket. 7. Reinstall the bulb and socket into the lamp assembly by turning it clockwise, making sure it is locked into place. 8. Reconnect the electrical connector. 9. Reinstall the lamp assembly on the car, making sure it is locked in...

  • Page 440

    Side indicators on external rear view mirrors – (if equipped) caution! The procedure is described as a guideline. For the replacement of the lamp it is recommended that you contact your authorized dealer. To replace the bulb proceed as follows: 1. Remove the mirror cap on the outside rear view mirro...

  • Page 441

    2. Remove the transparent lens assembly as shown. Removing the mirror cap transparent lens 8 in case of emergency 439.

  • Page 442

    3. Remove the bulb socket and bulb from the transparent lens assembly by rotating the socket counterclockwise. 4. Remove the bulb from the bulb socket by pulling the bulb straight out. 5. Insert the new bulb, making sure that it is locked into place 6. Reinstall the socket in to the transparent lens...

  • Page 443

    7. Reinstall the cover on the outside rear view mirror, making sure it is locked into place. Rear tail lamps contain the following: • position lights • stop lights • direction indicator • reverse lights to replace the bulbs proceed as follows: 1. Open the liftgate. 2. Using a suitable tool remove th...

  • Page 444

    4. Disconnect the electrical connector by pushing the release. 5. Remove the rear tail lamp, sliding it toward the outside as shown. Rear lamp fastener and electrical connector 1 — fastener 2 — electrical connector tail lamp removal 442 in case of emergency.

  • Page 445

    6. Unscrew the screws and remove the rear tail lamp holder. 7. Replace the bulb as necessary. 8. Insert the new bulb, making sure it is properly locked; rear lamp assembly 1 — mounting screws rear tail lamp holder 1 — tail light 2 — reverse bulb 3 — position light/stop light/turn signal 8 in case of...

  • Page 446

    9. Reassemble the lamp assembly on the rear tail lamp housing, tightening the screws. 10. Reposition the rear tail lamp on the car. 11. Secure the fastener of the rear tail lamp and reconnect the electrical connector. 12. Reinstall the door making sure of its correct locked 13. Finally close the tai...

  • Page 447

    2. Remove the bulbs from the individual side contacts. 3. Insert the new bulbs, and ensure that they are properly locked between the contacts. 4. Reinstall the license plate lens. Note: if removal the license plate lens using a screw- driver, be sure to cover the tip of the screwdriver with a cloth ...

  • Page 448

    Replacing interior bulbs front courtesy light to replace the bulbs proceed as follows: 1. Using a suitable tool remove the front courtesy light as shown. 2. Release the retainer clips and bulb housing as shown. Front courtesy light housing front courtesy bulb housing 1 — retaining clips 2 — bulb hou...

  • Page 449

    3. Replace the bulbs by pulling straight out of bulb housing. 4. Insert the new bulbs, making sure that they are properly locked. 5. Reassemble the bulb housing and courtesy light hous- ing making sure that they are properly locked. 6. Install the front courtesy light making sure that it is properly...

  • Page 450

    Dome light vanity mirror to replace the bulbs proceed as follows: 1. Lift the cover of the mirror and pull out the visor mirror light cover. 2. Replace the bulb, releasing it from the side contacts, and then insert the new bulb, making sure that it is properly locked between the contacts. 3. Reinsta...

  • Page 451

    Dome light glove compartment to replace the bulb proceed as follows: 1. Open the glove compartment; 2. Place your fingers inside the light assembly, pull the bulb to replace it. 3. Insert the new bulb, making sure it is properly locked. Rear dome light — without retractable roof to replace the bulbs...

  • Page 452

    3. Insert the new bulb, locking it between the contacts. 4. Reinstall the dome light. Dome light — my sky to replace the bulbs proceed as follows: 1. Lower the handle in the direction shown remove the dome light. 2. Replace the bulb by removing it from the side contacts. Retractable roof light 450 i...

  • Page 453

    3. Insert the new bulb, locking it between the contacts. 4. Reinstall the dome light. Interior cargo lights to replace the bulbs proceed as follows: 1. Open the luggage compartment and remove the dome light assembly. 2. Open the light cover and replace the bulb. 3. Close the light cover over the bul...

  • Page 454

    Warning! • before proceeding with the replacement of the lamp wait for the exhaust pipes are cool: danger of burns! • modifications or repair of the electrical system performed incorrectly and without taking into ac- count the technical characteristics can cause mal- functions with the risk of fire....

  • Page 455

    Warning! (continued) • if a general protection fuse for safety systems (air bag system, braking system), power unit systems (engine system, gearbox system) or steering system blows, contact an authorized dealer. General information the fuses protect electrical systems against excessive current. When...

  • Page 456

    Fuse removal to replace a fuse use the extractor attached to the fuse cover (located on the inside of the engine compartment fuse cover. Access to the fuses the fuses are grouped into four controllers located in the engine compartment, under the instrument panel and on the inside of the left side ca...

  • Page 457

    Engine compartment fuses/distribution unit the engine compartment fuse panel is located on the left side of the engine compartment. Engine compartment fuse cavities fuse panel & cover location 1 — mounting screw 2 — fuse cover 8 in case of emergency 455.

  • Page 458

    Removing fuse cover and locking screw proceed as follows: • slowly turn the screw counterclockwise. • slowly release the screw. • remove the fuse cover by sliding it upward. Mounting fuse cover and locking screw proceed as follows: • properly secure the fuse cover to the box, slide com- pletely from...

  • Page 459

    Cavity maxi fuse cartridge fuse micro fuse description f01 70 amp tan – – module body computer f02 70 amp tan – – module body computer, rear distribution units f03 – 20 amp blue – controller power supply body computer f04 – 30 amp pink – brake control electronics module f05 70 amp tan – – electric p...

  • Page 460

    Cavity maxi fuse cartridge fuse micro fuse description f08 – 30 amp pink – automatic transmission, gsm f09 – – 5 amp tan control module engine f10 – – 15 amp blue horn f11 – – 10 amp red – 1.4 engines 25 amp clear – 2.4 engines supply secondary loads f14 – – 7.5 amp brown heater ⬙ blow by ⬙ f14 – – ...

  • Page 461

    Cavity maxi fuse cartridge fuse micro fuse description f18 – – 20 amp yellow 12v rear cargo outlet ignition powered f19 – – 7.5 amp brown air conditioner compressor f20 – – 5 amp tan electronic power four-wheel drive f21 – – 15 amp blue fuel pump f22 – – 20 amp yellow power control module engine f23...

  • Page 462

    Cavity maxi fuse cartridge fuse micro fuse description f84 – – 30 amp green power supply all wheel drive f87 – – 5 amp tan shift lever automatic trans- mission f88 – – 7.5 amp brown heated outside mirrors f89 – – 30 amp green heated rear window f90 – – 5 amp tan ibs sensor (battery state of charge) ...

  • Page 463

    Body controller fuse cavities 8 in case of emergency 461.

  • Page 464

    Cavity mini fuse description f31 7.5 amp brown flashes/electrical movement front seats/fan air conditioning f33 20 amp yellow power window front (driver side) f34 20 amp yellow power window front (passenger side) f36 15 amp blue supply uconnect® system, air conditioning, alarm, power folding outside...

  • Page 465

    Cavity mini fuse description f49 7.5 amp brown supply parksense, spot lights front dome, mirror, electric motor retractable roof, heated front seats, stabilizer battery, esc system, esl f50 7.5 amp brown supply air bag f51 7.5 amp brown alarm power, front courtesy light, air condi- tioning compresso...

  • Page 466

    Rear cargo fuse/relay distribution unit to access the fuses, remove the access door from the left rear panel of the rear cargo area. The fuses may be contained in two units. Fuse holder no. 1 is located closest to the rear of the vehicle and fuse holder no. 2 (if equipped with trailer towing) is loc...

  • Page 467

    Fuse holder no. 1 cavity mini fuse description f1 30 amp blue power inverter f2 20 amp yellow hifi audio system f3 20 amp yellow my sky f4 7.5 amp brown lumbar adjustment front seat (driver side) f5 30 amp green power seat (driver side) f6 7.5 amp brown power seat (driver side and passenger side) f7...

  • Page 468

    Fuse holder no. 2 cavity mini fuse description f1 10 amp red controller exterior lighting on trailer f5 15 amp blue controller exterior lighting lights (drivers side) f6 15 amp blue controller exterior lighting lights (passenger side) 466 in case of emergency.

  • Page 469

    Jacking and tire changing warning! • do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel. • being under a jacked-up vehicle is dangerous. The vehicle could slip...

  • Page 470

    Jack location/spare tire stowage the jack and tools are located in the rear storage com- partment if equipped, inside a special container. Jack and tools 1 — wheel bolt wrench 2 — jack 3 — emergency funnel 4 — wheel chocks 5 — screwdriver 6 — emergency allen key 468 in case of emergency.

  • Page 471

    1. Open the liftgate. 2. Lift the access cover using the load floor pull strap. 3. Remove the fastener securing the spare tire. 4. Remove the chocks. 5. Remove the jack and wheel bolt wrench. 6. Remove the spare tire. Warning! A loose tire or jack thrown forward in a collision or hard stop could end...

  • Page 472

    Preparations for jacking 1. Park the vehicle on a firm level surface as far from the edge of the roadway as possible. Avoid icy or slippery areas. Warning! Do not attempt to change a tire on the side of the vehicle close to moving traffic, pull far enough off the road to avoid being hit when operati...

  • Page 473

    Warning! (continued) • turn on the hazard warning flasher. • chock the wheel diagonally opposite the wheel to be raised. • apply the parking brake and place an automatic transmission in park. • never start or run the engine with the vehicle on a jack. • do not let anyone sit in the vehicle when it i...

  • Page 474

    1. Remove the spare tire, jack, and wheel bolt wrench. 2. If equipped with wheels where the center cap covers the wheel bolts, use the wheel bolt wrench to pry the center cap off carefully before raising the vehicle. 3. Before raising the vehicle, use the wheel bolt wrench to loosen, but not remove,...

  • Page 475

    Front jacking location front jacking engagement point 8 in case of emergency 473.

  • Page 476

    5. Raise the vehicle just enough to remove the flat tire. Rear jacking location rear jacking engagement point 474 in case of emergency.

  • Page 477

    Warning! Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. 6. Remove the wheel bolts and tire. 7. Mount the spare tire. Caution! Be sure to mount the spare tire with the v...

  • Page 478

    Note: • your vehicle may be equipped with a compact spare tire or a limited — use spare tire. For further infor- mation refer to “tires — general information” in “maintaining and caring for your vehicle”. • for vehicles so equipped, do not attempt to install a center cap or wheel cover on the compac...

  • Page 479

    11. Securely stow the jack, tools, chocks and flat tire. Warning! A loose tire or jack thrown forward in a collision or hard stop could endanger the occupants of the ve- hicle. Always stow the jack parts and the spare tire in the places provided. Have the deflated (flat) tire repaired or replaced im...

  • Page 480

    Warning! To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts fully until the vehicle has been lowered. Failure to follow this warning may result in serious injury. 3. Lower the vehicle to the ground by turning the jack handle counterclockwise. 4. Finish tightening the ...

  • Page 481

    Tire service kit — if equipped if a tire is punctured, you can make a first emergency repair using the tire service kit located in the rear storage compartment inside the storage container. Tire punctures of up to 1/4” (6 mm) can be repaired; the kit can be used in all weather conditions. Do not rem...

  • Page 482

    Warning! (continued) • do not use tire service kit or drive the vehicle under the following circumstances: – if the puncture in the tire tread is approximately 1/4 inch (6 mm) or larger. – if the tire has any sidewall damage. – if the tire has any damage from driving with extremely low tire pressure...

  • Page 483

    Warning! (continued) • tire service kit sealant solution contains latex. In case of an allergic reaction or rash, consult a physician immediately. Keep tire service kit out of reach of children. If swallowed, rinse mouth immediately with plenty of water and drink plenty of water. Do not induce vomit...

  • Page 484

    If the pressure is at 19 psi (1.3 bar) or above repeat the inflation process to reach the correct tire pressure and continue driving. Peel off the warning label from the bottle and place it on the dashboard as a reminder to the driver that the tire has been treated with tire service kit. Warning! Th...

  • Page 485

    Jump starting if your vehicle has a discharged battery it can be jump- started using a set of jumper cables and a battery in another vehicle or by using a portable battery booster pack. Jump starting can be dangerous if done improperly so please follow the procedures in this section carefully. Note:...

  • Page 486

    Preparations for jump start the battery in your vehicle is located in the front of the engine compartment, behind the left headlight assembly. Note: the positive battery post is covered with a protective cap. Lift up on the cap to gain access to the positive battery post. Warning! • take care to avo...

  • Page 487

    Proceed as follows: 1. Set the electric park brake, shift the automatic trans- mission into park (manual transmission in neu- tral) and turn the ignition to stop/off. 2. Turn off the heater, radio, and all unnecessary electri- cal accessories. 3. If using another vehicle to jump start the battery, p...

  • Page 488

    3. Connect the negative (-) end of the jumper cable to the negative (-) post of the booster battery. 4. Connect the opposite end of the negative (-) jumper cable to a good engine ground (exposed metal part of the discharged vehicle’s engine) away from the battery and the fuel injection system. Warni...

  • Page 489

    4. Disconnect the opposite end of the positive (+) jumper cable from the positive (+) post of the vehicle with the discharged battery. If frequent jump starting is required to start your vehicle you should have the battery and charging system in- spected at your authorized dealer. Caution! Accessori...

  • Page 490

    • turn off the hvac blower motor. • close the hvac circulation door. System reset procedure depending on the nature of the event the left and right turn signal lights, located in the instrument panel, may both be blinking and will continue to blink until the ignition switch is turned to the off posi...

  • Page 491

    Customer action customer will see 7. Turn left turn signal switch off. (turn signal switch must be placed in neutral state). Left turn light is off. Right turn light is off. 8. Turn ignition off. 9. Turn hazard flashers off (manually). System is now reset and the engine may be started. If a reset pr...

  • Page 492

    Caution! Driving with a hot cooling system could damage your vehicle. If the temperature gauge reads “h,” pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on the “h” and you hear continuous...

  • Page 493

    3. Carefully separate the shift lever bezel and boot assembly from the center console. 4. Push and maintain firm pressure on the brake pedal. Shift lever bezel location removing shift lever bezel 8 in case of emergency 491.

  • Page 494

    5. Insert a small screwdriver or similar tool down into the shift lever override access hole (at the right front corner of the shift lever assembly), and push and hold the override release lever down. 6. Move the shift lever to the neutral position. 7. The vehicle may then be started in neutral. 8. ...

  • Page 495

    4. Using the special tool supplied (located in the tool bag), remove the screws in the lower steering column trim cover and remove it. Special tool lower steering column cover 1 — trim screws 8 in case of emergency 493.

  • Page 496

    5. With one hand, pull down on the release tab and with the other, pull out the ignition key. 6. Once the key is removed, reinstall the steering column cover. Release tab location release tab direction 494 in case of emergency.

  • Page 497

    Freeing a stuck vehicle if your vehicle becomes stuck in mud, sand or snow, it can often be moved using a rocking motion. Turn the steering wheel right and left to clear the area around the front wheels. For vehicles with automatic transmission, push and hold the lock button on the shift lever. Then...

  • Page 498

    Caution! (continued) • revving the engine or spinning the wheels too fast may lead to transmission overheating and failure. It can also damage the tires. Do not spin the wheels above 30 mph (48 km/h) while in gear (no trans- mission shifting occurring). Warning! Fast spinning tires can be dangerous....

  • Page 499

    Towing the car/towing a disabled vehicle this section describes procedures for towing a disabled vehicle using a commercial towing service. Fwd models four wheel drive towing condition wheels off the ground automatic transmission manual transmission automatic/manual transmission 4x4 flat tow none no...

  • Page 500

    Note: vehicles with a discharged battery or total electrical failure when the electric park brake (epb) is engaged, will need a wheel dolly or jack to raise the rear wheels off the ground when moving the vehicle onto a flatbed. If you must use the accessories (wipers, defrosters, etc.) while being t...

  • Page 501

    Four-wheel drive (4wd) the manufacturer requires towing with all four wheels off the ground. Acceptable methods are to tow the vehicle on a flatbed, or with one end of the vehicle raised and the opposite end on a towing dolly. Caution! • do not tow this vehicle with any of its wheels on the ground. ...

  • Page 502

    Note: for off-road recovery, it is recommended to use both of the front tow hooks to minimize the risk of damage to the vehicle. Vehicles equipped with rke transmitter with an integrated vehicle key turn the ignition key to the mar/run and then stop/ off position, without removing it. By extracting ...

  • Page 503

    Vehicles with keyless enter-n-go™ place the ignition in the run and subsequently on stop, without opening the door. During towing remember that not having the aid of the power brakes and the electro- mechanical power steering, greater force is needed in applying the brakes and steering of the vehicl...

  • Page 505

    Maintaining and caring for your vehicle contents 䡵 emissions inspection and maintenance programs . . . . . . . . . . . . .505 䡵 replacement parts . . . . . . . . . . . . . . . . . .506 䡵 dealer service . . . . . . . . . . . . . . . . . . . . . .506 䡵 maintenance schedule . . . . . . . . . . . . .507...

  • Page 506

    ▫ manual transmission — if equipped . . . . . . .538 ▫ automatic transmission — if equipped . . . . .538 ▫ appearance care and protection from corrosion . . . . . . . . . . . . . . . . . . . . . . . . . . .540 䡵 lifting a vehicle . . . . . . . . . . . . . . . . . . .547 䡵 tire safety information . ....

  • Page 507

    Emissions inspection and maintenance programs in some localities, it may be a legal requirement to pass an inspection of your vehicle’s emissions control system. Failure to pass could prevent vehicle registration. For states that require an inspection and mainte- nance (i/m), this check verifies the...

  • Page 508

    • the mil will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine. This means that your vehicle’s obd ii system is ready and you can proceed to the i/m station. If your obd ii system is not ready, you should see your authorized dea...

  • Page 509

    Note: intentional tampering with emissions control systems may void your warranty and could result in civil penalties being assessed against you. Warning! You can be badly injured working on or around a motor vehicle. Only do service work for which you have the knowledge and the proper equipment. If...

  • Page 510

    Note: under no circumstances should oil change inter- vals exceed 10,000 miles (16,000 km) or one year, which- ever comes first. Severe duty all models change engine oil at 4,000 miles (6,500 km) if the vehicle is operated in a dusty and off road environment. This type of vehicle use is considered s...

  • Page 511

    Maintenance chart mileage or time passed (whichever comes first) 10,000 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 years 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers 16,000 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 ...

  • Page 512

    Mileage or time passed (whichever comes first) 10,000 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 years 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers 16,000 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,000 19...

  • Page 513

    Mileage or time passed (whichever comes first) 10,000 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 years 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers 16,000 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,000 19...

  • Page 514

    Mileage or time passed (whichever comes first) 10,000 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 years 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers 16,000 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,000 19...

  • Page 515

    Mileage or time passed (whichever comes first) 10,000 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 years 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers 16,000 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,000 19...

  • Page 516

    (**) the spark plug change is distance based only, yearly intervals do not apply. The following are essential to ensure correct operation and prevent serious damage to the engine: • only use spark plugs of the same make and type which are specially certified for such engines (refer to “engine inform...

  • Page 517

    Engine compartment — 1.4l turbo engine 1 — air cleaner filter 4 — battery 7 — coolant pressure cap 2 — engine oil dipstick 5 — power distribution center (fuses) 8 — coolant pressure bottle 3 — brake fluid reservoir 6 — washer fluid reservoir 9 — oil fill cap 9 maintaining and caring for your vehicle...

  • Page 518

    Engine compartment — 2.4l engine 1 — engine air cleaner filter 4 — brake fluid reservoir 7 — washer fluid reservoir 2 — engine oil dipstick 5 — battery 8 — coolant pressure bottle 3 — engine oil fill cap 6 — power distribution center (fuses) 516 maintaining and caring for your vehicle.

  • Page 519

    Maintenance procedures the pages that follow contain the required maintenance services determined by the engineers who designed your vehicle. Besides those maintenance items specified in the fixed maintenance schedule, there are other components which may require servicing or replacement in the futu...

  • Page 520

    After a fully warmed engine is shut off. Do not check oil level before starting the engine after it has sat overnight. Checking engine oil level when the engine is cold will give you an incorrect reading. Checking the oil while the vehicle is on level ground, and approximately five minutes after a f...

  • Page 521

    Engine oil selection — 1.4l turbo engine for best performance and maximum protection for tur- bocharged engines under all types of operating condi- tions, the manufacturer recommends synthetic engine oils that are api certified and meet the requirements of fca us material standard ms-12991. Engine o...

  • Page 522

    Lubricants which do not have both the engine oil certi- fication mark and the correct sae viscosity grade num- ber should not be used. Materials added to engine oil the manufacturer strongly recommends against the ad- dition of any additives (other than leak detection dyes) to the engine oil. Engine...

  • Page 523

    Warning! The air induction system (air cleaner, hoses, etc.) can provide a measure of protection in the case of engine backfire. Do not remove the air induction system (air cleaner, hoses, etc.) unless such removal is necessary for repair or maintenance. Make sure that no one is near the engine comp...

  • Page 524

    Warning! (continued) an output greater than 12 volts. Do not allow cable clamps to touch each other. • battery posts, terminals, and related accessories contain lead and lead compounds. Wash hands after handling. • the battery in this vehicle has a vent hose that should not be disconnected and shoul...

  • Page 525

    Warning! • use only refrigerants and compressor lubricants approved by the manufacturer for your air condi- tioning system. Some unapproved refrigerants are flammable and can explode, injuring you. Other unapproved refrigerants or lubricants can cause the system to fail, requiring costly repairs. Re...

  • Page 526

    Body lubrication locks and all body pivot points, including such items as seat tracks, door hinge pivot points and rollers, liftgate, tailgate, decklid, sliding doors and hood hinges, should be lubricated periodically with a lithium based grease, such as mopar® spray white lube to assure quiet, easy...

  • Page 527

    Note: life expectancy of wiper blades varies depending on geographical area and frequency of use. Poor perfor- mance of blades may be present with chattering, marks, water lines or wet spots. If any of these conditions are present, clean the wiper blades or replace as necessary. Service position str...

  • Page 528

    Front wiper blade removal/installation 1. Lift the front wiper arm upward to raise the wiper blade off of the windshield. 2. Push the release button on the arm of the wiper blade. 3. Push the wiper blade up the and remove it. 4. Install the wiper blade and firmly push the wiper blade until it snaps ...

  • Page 529

    Rear wiper blade removal/installation 1. Carefully lift the rear wiper arm upward to raise the wiper blade off of the liftgate glass. 2. Grab and hold the wiper arm closest to the wiper blade end while pushing the wiper blade towards the liftgate glass to unsnap the blade pivot pin from the wiper bl...

  • Page 530

    Have an authorized technician inspect the complete ex- haust system and adjacent body areas for broken, dam- aged, deteriorated, or mispositioned parts. Open seams or loose connections could permit exhaust fumes to seep into the passenger compartment. In addition, have the exhaust system inspected e...

  • Page 531

    Caution! (continued) performance, have your vehicle serviced promptly. Continued operation of your vehicle with a severe malfunction could cause the converter to overheat, resulting in possible damage to the converter and vehicle. Under normal operating conditions, the catalytic con- verter will not...

  • Page 532

    Cooling system warning! • when working near the radiator cooling fan, dis- connect the fan motor lead or turn the ignition switch to the off position. The fan is temperature controlled and can start at any time the ignition switch is in the on position. • you or others can be badly burned by hot eng...

  • Page 533

    Refer to the “maintenance schedule” for the proper maintenance intervals. Selection of coolant refer to “fluids, lubricants, and genuine parts” in the “technical data” section for further information. Caution! • mixing of engine coolant (antifreeze) other than specified organic additive technology (...

  • Page 534

    Adding coolant your vehicle has been built with an improved engine coolant (oat coolant conforming to ms.90032) that al- lows extended maintenance intervals. This engine cool- ant (antifreeze) can be used up to ten years or 150,000 miles (240,000 km) before replacement. To pre- vent reducing this ex...

  • Page 535

    Note: • some vehicles require special tools to add coolant properly. Failure to fill these systems properly could lead to severe internal engine damage. If any coolant is needed to be added to the system please contact your local authorized dealer. • mixing engine coolant (antifreeze) types is not r...

  • Page 536

    Disposal of used engine coolant used ethylene glycol-based engine coolant (antifreeze) is a regulated substance requiring proper disposal. Check with your local authorities to determine the disposal rules for your community. To prevent ingestion by ani- mals or children, do not store ethylene glycol...

  • Page 537

    • check the coolant freeze point in the radiator and in the coolant expansion bottle. If engine coolant (anti- freeze) needs to be added, the contents of the coolant expansion bottle must also be protected against freez- ing. • if frequent engine coolant (antifreeze) additions are required, the cool...

  • Page 538

    Brake master cylinder the fluid level in the master cylinder should be checked when performing under hood services, or immediately if the “brake warning light” is on. Be sure to clean the top of the master cylinder area before removing the cap. If necessary, add fluid to bring the fluid level up to ...

  • Page 539

    Warning! (continued) • to avoid contamination from foreign matter or moisture, use only new brake fluid or fluid that has been in a tightly closed container. Keep the master cylinder reservoir cap secured at all times. Brake fluid in a open container absorbs moisture from the air resulting in a lowe...

  • Page 540

    Manual transmission — if equipped lubricant selection use only the manufacturers recommended transmission fluid. Refer to “fluids, lubricants, and genuine parts” in “maintaining and caring for your vehicle” for further information. Please see your authorized dealer for service. Fluid level check che...

  • Page 541

    Note: no chemical flushes should be used in any trans- mission; only the approved lubricant should be used. Caution! Using a transmission fluid other than the manufac- turer’s recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder. Refer to “fluids, l...

  • Page 542

    Caution! If a transmission fluid leak occurs, visit your autho- rized dealer immediately. Severe transmission dam- age may occur. Your authorized dealer has the proper tools to adjust the fluid level accurately. Fluid and filter changes under normal operating conditions, the fluid installed at the f...

  • Page 543

    What causes corrosion? Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle. The most common causes are: • road salt, dirt and moisture accumulation. • stone and gravel impact. • insects, tree sap and tar. • salt in the air near seacoast localities. ...

  • Page 544

    Caution! (continued) • if the engine compartment is washed with an high pressure jet, keep it at a distance of at least 8 inches (20 centimeters) from filler surface. Special care • if you drive on salted or dusty roads or if you drive near the ocean, hose off the undercarriage at least once a month...

  • Page 545

    Note: if your vehicle is equipped with dark vapor or black satin chrome wheels do not use wheel cleaners, abrasives or polishing compounds. They will perma- nently damage this finish and such damage is not cov- ered by the new vehicle limited warranty. Use only mild soap and water with a soft cloth....

  • Page 546

    Interior care use mopar® total clean to clean fabric upholstery and carpeting. Use mopar® total clean to clean vinyl upholstery. Mopar® total clean is specifically recommended for leather upholstery. Your leather upholstery can be best preserved by regular cleaning with a damp soft cloth. Small part...

  • Page 547

    Caution! Do not use alcohol and alcohol-based and/or keton based cleaning products to clean leather seats, as damage to the seat may result. Cleaning headlights your vehicle has plastic headlights that are lighter and less susceptible to stone breakage than glass headlights. Plastic is not as scratc...

  • Page 548

    Instrument panel bezels caution! When installing hanging air fresheners in your vehicle, read the installation instructions carefully. Some air fresheners will damage the finish of painted or deco- rated parts if allowed to directly contact any surface. Cleaning plastic instrument cluster lenses the...

  • Page 549

    Warning! A frayed or torn belt could rip apart in a collision and leave you with no protection. Inspect the belt system periodically, checking for cuts, frays, or loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Seat belt assemblies must be replaced a...

  • Page 550

    Lifting point locations 548 maintaining and caring for your vehicle.

  • Page 551

    Tire safety information tire markings note: • p (passenger) — metric tire sizing is based on u.S. Design standards. P-metric tires have the letter “p” molded into the sidewall preceding the size designa- tion. Example: p215/65r15 95h. • european — metric tire sizing is based on european design stand...

  • Page 552

    • temporary spare tires are designed for temporary emergency use only. Temporary high pressure com- pact spare tires have the letter “t” or “s” molded into the sidewall preceding the size designation. Example: t145/80d18 103m. • high flotation tire sizing is based on u.S. Design standards and it beg...

  • Page 553

    Example: r = construction code – ⬙ r ⬙ means radial construction, or – ⬙ d ⬙ means diagonal or bias construction 15, 16, 18 = rim diameter in inches (in) service description: 95 = load index – a numerical code associated with the maximum load a tire can carry h = speed symbol – a symbol indicating t...

  • Page 554

    Example: load identification: absence of the following load identification symbols on the sidewall of the tire indicates a standard load (sl) tire: • xl = extra load (or reinforced) tire, or • ll = light load tire or • c, d, e, f, g = load range associated with the maximum load a tire can carry at a...

  • Page 555

    Example: dot ma l9 abcd 0301 dot = department of transportation – this symbol certifies that the tire is in compliance with the u.S. Department of transportation tire safety standards and is approved for highway use ma = code representing the tire manufacturing location (two digits) l9 = code repres...

  • Page 556

    Tire terminology and definitions term definition b-pillar the vehicle b-pillar is the structural member of the body located behind the front door. Cold tire inflation pressure cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least three hours,...

  • Page 557

    Tire loading and tire pressure tire and loading information placard location note: the proper cold tire inflation pressure is listed on the driver’s side b-pillar or the rear edge of the driver’s side door. Example tire placard location (door) example tire placard location (b-pillar) 9 maintaining a...

  • Page 558

    Tire and loading information placard this placard tells you important information about the: 1. Number of people that can be carried in the vehicle. 2. Total weight your vehicle can carry. 3. Tire size designed for your vehicle. 4. Cold tire inflation pressures for the front, rear, and spare tires. ...

  • Page 559

    To determine the maximum loading conditions of your vehicle, locate the statement “the combined weight of occupants and cargo should never exceed xxx lbs or xxx kg” on the tire and loading information placard. The combined weight of occupants, cargo/luggage and trailer tongue weight (if applicable) ...

  • Page 560

    Note: • if your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. The follow- ing table shows examples on how to calculate total load, cargo/luggage, and towing capacities of your vehicle with varying seating configurations and num- ber and size of occupan...

  • Page 561

    9 maintaining and caring for your vehicle 559.

  • Page 562

    Warning! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. Tires — general information tire pressure proper tire inflation pressur...

  • Page 563

    Warning! (continued) • always drive with each tire inflated to the recom- mended cold tire inflation pressure. Both under-inflation and over-inflation affect the stability of the vehicle and can produce a feeling of sluggish response or over responsiveness in the steering. Note: • unequal tire press...

  • Page 564

    • inspect tires for signs of tire wear or visible damage. Caution! After inspecting or adjusting the tire pressure, al- ways reinstall the valve stem cap. This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Inflation pressures specified on the placard...

  • Page 565

    Loading may be required for high-speed vehicle opera- tion. Refer to your authorized tire dealer or original equipment vehicle dealer for recommended safe operat- ing speeds, loading and cold tire inflation pressures. Warning! High speed driving with your vehicle under maxi- mum load is dangerous. T...

  • Page 566

    Consult an authorized tire dealer for tire repairs and additional information. Damaged run flat tires, or run flat tires that have experienced a loss of pressure should be replaced imme- diately with another run flat tire of identical size and service description (load index and speed symbol). Tire ...

  • Page 567

    Warning! Do not use summer tires in snow/ice conditions. You could lose vehicle control, resulting in severe injury or death. Driving too fast for conditions also creates the possibility of loss of vehicle control. Snow tires some areas of the country require the use of snow tires during the winter....

  • Page 568

    Run flat tire reaches the run flat mode it has limited driving capabilities and needs to be replaced immedi- ately. A run flat tire is not repairable. It is not recommended driving a vehicle loaded at full capacity or to tow a trailer while a tire is in the run flat mode. See the tire pressure monit...

  • Page 569

    Warning! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause tire dam- age or failure. A tire could explode and injure some- one. Do not spin your vehicle’s wheels faster than 30 mph (48 km/h) for more than 30 seconds continu- ously when you are stuck, and do...

  • Page 570

    Worn to the tread wear indicators, the tire should be replaced. Refer to “replacement tires” in this section for further information. Life of tire the service life of a tire is dependent upon varying factors including, but not limited to: • driving style. • tire pressure - improper cold tire inflati...

  • Page 571

    Replacement tires the tires on your new vehicle provide a balance of many characteristics. They should be inspected regularly for wear and correct cold tire inflation pressures. The manu- facturer strongly recommends that you use tires equiva- lent to the originals in size, quality and performance w...

  • Page 572

    Warning! (continued) braking of your vehicle. This can cause unpredict- able handling and stress to steering and suspen- sion components. You could lose control and have a collision resulting in serious injury or death. Use only the tire and wheel sizes with load ratings approved for your vehicle. •...

  • Page 573

    Front wheel drive (fwd) models • original equipment 215/60r17 and 225/55r18 tire sizes are not chainable. • the use of 7mm snow chains is permitted with the use of 215/60r16 tires. Four wheel drive (4wd) non-trailhawk models with- out a two-speed power takeoff unit • original equipment 215/60r17 and...

  • Page 574

    Warning! Using tires of different size and type (m+s, snow) between front and rear axles can cause unpredictable handling. You could lose control and have a collision. Caution! To avoid damage to your vehicle or tires, observe the following precautions: • because of restricted traction device cleara...

  • Page 575

    Tire rotation recommendations the tires on the front and rear of your vehicle operate at different loads and perform different steering, handling, and braking functions. For these reasons, they wear at unequal rates. These effects can be reduced by timely rotation of tires. The benefits of rotation ...

  • Page 576

    The suggested four wheel drive (4wd) tire rotation method is the “forward-cross” shown in the following diagram. Caution! Proper operation of four-wheel drive vehicles de- pends on tires of equal size, type and circumference on each wheel. Any difference in tire size can cause damage to the power tr...

  • Page 577

    • if you do not disconnect the battery from the electrical system, check the battery charge every thirty days. • clean and protect the painted parts by applying pro- tective waxes. • clean and protect polished metal parts by applying protective waxes. • apply talcum powder to the front and rear wipe...

  • Page 579

    Technical data contents 䡵 vehicle identification . . . . . . . . . . . . . . .578 ▫ chassis number . . . . . . . . . . . . . . . . . . . . . .578 䡵 wheel and tire torque specifications . . . . . . . . . . . . . . . . . . . . . .579 ▫ torque specifications . . . . . . . . . . . . . . . . . . .579 䡵 f...

  • Page 580

    Vehicle identification chassis number the chassis number (vin) is stamped on a plate located on the left front corner of the instrument panel cover, which is visible from outside the car through the windshield. This number is also stamped on the floor of the passenger compartment, near the right fro...

  • Page 581

    Wheel and tire torque specifications proper lug nut/bolt torque is very important to ensure that the wheel is properly mounted to the vehicle. Any time a wheel has been removed and reinstalled on the vehicle the lug nuts/bolts should be torqued using a properly calibrated torque wrench. Torque speci...

  • Page 582

    Tighten the lug nuts/bolts in a star pattern until each nut/bolt has been tightened twice. After 25 miles (40 km) check the lug nut/bolt torque to be sure that all the lug nuts/bolts are properly seated against the wheel. Warning! To avoid the risk of forcing the vehicle off the jack, do not tighten...

  • Page 583

    Fluid capacities u.S metric fuel (approximate) 1.4l turbo/2.4l engine 12.7 gallons 48 liters engine oil with filter 1.4l turbo engine (sae 5w-40 synthetic, api certified) 4.0 quarts 3.8 liters 2.4l engine (sae 0w-20, api certified) 5.5 quarts 5.2 liters cooling system * 1.4l turbo engine (mopar® ant...

  • Page 584

    Fluids, lubricants, and genuine parts engine component fluid, lubricant, or genuine part engine coolant we recommend you use mopar® antifreeze/coolant 10 year/150,000 mile formula oat (organic additive technology) or equivalent meeting the requirements of fca material standard ms.90032. Engine oil –...

  • Page 585

    Component fluid, lubricant, or genuine part engine oil – 2.4l engine we recommend you use sae 0w-20 api certified engine oil, meeting the requirements of fca us mate- rial standard ms-6395 such as mopar, pennzoil, and shell helix. Refer to your engine oil filler cap for correct sae grade. Engine oil...

  • Page 586

    Chassis component fluid, lubricant, or genuine part manual transmission – if equipped we recommend you use mopar® c series manual & dual dry clutch transmission fluid. Automatic transmission – if equipped use only mopar® zf 8&9 speed atf™ automatic transmission fluid, or equivalent. Failure to use t...

  • Page 587

    Multimedia contents 䡵 uconnect® settings. . . . . . . . . . . . . . . . . . . .587 ▫ buttons on the faceplate. . . . . . . . . . . . . . . .588 ▫ buttons on the touchscreen. . . . . . . . . . . . . .589 ▫ customer programmable features — uconnect® 5.0 settings . . . . . . . . . . . . . . . . .589 ▫ ...

  • Page 588

    ▫ media. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .635 ▫ phone. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .636 ▫ voice text reply . . . . . . . . . . . . . . . . . . . . . .638 ▫ navigation (6.5an) . . . . . . . . . . . . . . . . . . . .639 ▫ uconnect® access* (6.5a/6.5a...

  • Page 589

    Uconnect® settings the uconnect® system uses a combination of buttons on the touchscreen and buttons on the faceplate located on the center of the instrument panel that allow you to access and change the customer programmable features. Many features can vary by vehicle. Uconnect® 5.0 buttons on the ...

  • Page 590

    Buttons on the faceplate buttons on the faceplate are located below, and beside the uconnect® system in the center of the instrument panel. In addition, there is a scroll/enter control knob located on the right side. Turn the control knob to scroll through menus and change settings (i.E., 30, 60, 90...

  • Page 591

    Buttons on the touchscreen buttons on the touchscreen are accessible on the uconnect® touchscreen. Customer programmable features — uconnect® 5.0 settings push the + more button on the faceplate, then press the “settings” button on the touchscreen to display the settings menu screen. In this mode th...

  • Page 592

    Display after pressing the “display” button on the touchscreen the following settings will be available. • display mode when in this display you may select the “auto” or “manual” display settings. To change mode status, press and release the “auto” or “manual” button on the touchscreen. Then press t...

  • Page 593

    Units after pressing the “units” button on the touchscreen you may select each unit of measure independently displayed in the electronic vehicle information system (evic) or driver information display (did). The following select- able units of measure are listed below: • us changes the evic/did to u...

  • Page 594

    • show command list when in this display, you may change the show com- mand list settings. To change the show command list settings, press the “show command list” button on the touchscreen and select from “always,” “with help” or “never.” press the back arrow button on the touchscreen to return to t...

  • Page 595

    • sync time — if equipped when in this display, you may sync the time with gps. Press the “sync time” button on the touchscreen and select from “on” or “off.” press the back arrow or done button on the touchscreen to return to the previous menu. Safety/assistance after pressing the “safety/assistanc...

  • Page 596

    • parkview® backup camera fixed guide lines — if equipped when this feature is enabled, fixed (static) grid lines are overlaid on the rear backup camera image to illustrate the width of the vehicle. • forward collision warning-plus (fcw+) — if equipped the front collision warning (fcw+) feature can ...

  • Page 597

    System can be enabled with sound only, or sound and display. To change the parksense® status, press and release the “sound only” or “sounds and display” button. Then press the back arrow button on the touch- screen. Refer to “parksense®” in “starting and operat- ing” for system function and operatin...

  • Page 598

    • lanesense strength — if equipped when this feature is selected, it sets the strength of the steering wheel feedback for potential lane departures. The amount of directional torque the steering system can apply to the steering wheel to correct for vehicle lane departure can be set at “low,” “medium...

  • Page 599

    • electric park brake service mode this feature provides a means for a technician or vehicle owner to utilize a vehicle integrated, menu driven system, to command the electric park brake retraction, to service the rear foundation brakes (brake pads, calipers, rotors, etc.). For further information, ...

  • Page 600

    • greeting lights when this feature is selected, it allows the greeting lights to be turned on or off. To change the greeting lights setting, press the “on” or “off” button on the touch- screen to select your desired greeting light setting. Press the back arrow button on the touchscreen to return to...

  • Page 601

    • flash lights with lock — if equipped when this feature is selected, the exterior lights will flash when the doors are locked or unlocked with the remote keyless entry (rke) transmitter. This feature may be selected with or without the sound horn on lock feature selected. To make your selection, pr...

  • Page 602

    • horn with lock when this feature is selected, the horn will sound when the key fob lock button is pressed. To make your selection, press the “horn w/lock” button on the touch- screen and select from ⬙ off,” “1st press,” or “2nd press” press the back arrow/done button on the touchscreen to return t...

  • Page 603

    Note: if “all” is programmed, all doors will unlock no matter which passive entry equipped door handle is grasped. If “driver” is programmed, only the driver’s door will unlock when the driver’s door is grasped. Touching the handle more than once will only result in the driver’s door opening once. I...

  • Page 604

    • headlight off delay when this feature is selected, the driver can choose to have the headlights remain on for 0, 30, 60, or 90 seconds when exiting the vehicle. To change the headlight off delay status press the “+” or “–” button on the touch- screen to select your desired time interval. Press the...

  • Page 605

    • perform compass calibration press the “calibration” button on the touchscreen to change this setting. This compass is self-calibrating, which eliminates the need to manually reset the compass. When the vehicle is new, the compass may appear erratic until it is calibrated. You may also calibrate th...

  • Page 606

    • balance/fade when in this display you may adjust the balance and fade settings. • speed adjusted volume this feature increases or decreases volume relative to vehicle speed. To change the speed adjusted volume press the “off,” “1,” “2” or “3” button on the touchscreen. Then press the back arrow bu...

  • Page 607

    Phone/bluetooth® after pressing the “phone/bluetooth®” button on the touchscreen the following settings will be available: • paired phones this feature shows which phones are paired to the phone/bluetooth® system. For further information, refer to the uconnect® supplement manual. Siriusxm setup — if...

  • Page 608

    Restore settings after pressing the “restore settings” button on the touchscreen the following settings will be available: • restore settings when this feature is selected it will reset the display, clock, audio, and radio settings to their default settings. To restore the settings to their default ...

  • Page 609

    Customer programmable features — uconnect® 6.5a/6.5an settings press the settings button to display the menu setting screen. In this mode the uconnect® system allows you to access programmable features that may be equipped such as display, clock, safety & driving assistance, lights, doors & locks, a...

  • Page 610

    Note: when day or night is selected for the display mode, the usage of the parade mode feature will cause the radio to activate the display brightness day control even though the headlights are on. • display brightness with headlights on this feature will allow you to select the brightness with the ...

  • Page 611

    Units • units when in this display, you may select to have the elec- tronic vehicle information system (evic) or driver in- formation display (did), odometer, and navigation sys- tem (if equipped) changed between us and metric units of measure. Press “us” or “metric.” press the back arrow button on ...

  • Page 612

    Clock after pressing the “clock” button on the touchscreen the following settings will be available: • show time in status bar this feature will allow you to turn on or shut off the digital clock in the status bar. To change the show time status setting press the “on” or “off” button on the touchscr...

  • Page 613

    • set hours this feature will allow you to adjust the hours. The sync time with gps “on” button must not be selected. To make your selection, press the “–” or “+” buttons on the touchscreen to adjust the hours up or down. Press the back arrow button on the touchscreen to return to the previous menu....

  • Page 614

    Collision warning” button and select the “near” or “far” button. Press the back arrow/done button on the touch- screen to return to the previous menu. • forward collision warning-plus (fcw+) active braking — if equipped the fcw+ system includes advanced brake assist (aba). When this feature is selec...

  • Page 615

    Can be set at “low,” “med” or “high.” to change the lanesense strength status, press the “lanesense strength” button and select from the “low,” “medium” or “high” buttons. Press the back arrow/done button on the touch- screen to return to the previous menu. For further information, refer to “lane de...

  • Page 616

    Change the blind spot alert status, press the “blind spot alert” button and select from “off,” “lights” or “lights & chimes.” then press the back arrow/done button on the touchscreen. Note: if your vehicle has experienced any damage in the area where the sensor is located, even if the fascia is not ...

  • Page 617

    Touchscreen, then the “safety & driving assistance” button on the touchscreen. Press the “parkview backup camera delay” button on the touchscreen to turn the parkview® delay on or off. • brakes this feature provides a means for a technician or vehicle owner to utilize a vehicle integrated, menu driv...

  • Page 618

    • headlight off delay when this feature is selected, it allows the adjustment of the amount of time the headlights remain on after the engine is shut off. To change the headlights off delay setting, press the headlights off delay button on the touchscreen, and choose either 0 sec, 30 sec, 60 sec or ...

  • Page 619

    • cornering lights when this feature is selected, if the steering wheel rotation angle is large or the turn signal indicators are on, a light (incorporated in the fog light) will turn on, on the relevant side to improve visibility at night. To change the cornering lights setting, press the “on” or “...

  • Page 620

    Doors & locks after pressing the “doors & locks” button on the touch- screen the following settings will be available: • auto door locks when this feature is selected, all doors will lock auto- matically when the vehicle reaches a speed of 15 mph (24 km/h). To make your selection, press the “auto lo...

  • Page 621

    Setting has been selected. Press the back arrow/done button on the touchscreen to return to the previous menu. • sound horn with remote start when this feature is selected, the horn will sound when the remote start is activated. To make your selection, press the “sound horn with remote start” button...

  • Page 622

    • memory linked to key fob — if equipped this feature provides automatic driver seat positioning to enhance driver mobility when entering and exiting the vehicle. To make your selection, press the “memory linked to key fob” button on the touchscreen and select from “on” or “off.” press the back arro...

  • Page 623

    Either front door will cancel this feature. To change the engine off power delay status press the “0 seconds,” “45 seconds,” “5 minutes” or “10 minutes” button on the touchscreen. Press the back arrow button on the touch- screen to return to the previous menu. Audio after pressing the “audio” button...

  • Page 624

    • aux volume offset — if equipped this feature provides the ability to tune the audio level for portable devices connected through the aux input. To make your selection, press the “aux volume offset” button on the touchscreen, select any point on the scale between the “+” and “–” buttons on the touc...

  • Page 625

    Exclude undesirable channels while scanning. To make your selection, press the “channel skip” button on the touchscreen, select the channels you would like to skip followed by pressing the back arrow button on the touchscreen. • subscription information new vehicle purchasers or lessees will receive...

  • Page 626

    Clear personal data after pressing the “clear personal data settings” button on the touchscreen the following settings will be avail- able: • clear personal data when this feature is selected it will remove personal data including bluetooth® devices and presets. To clear per- sonal data press the “y...

  • Page 627

    Located below the heating ventilation and air condition- ing controls is the front usb port. Refer to the uconnect® radio supplement for external usb support capability. Center console usb port located in the center console is a second usb port. Note: depending on vehicle configuration, the usb port...

  • Page 628

    Steering wheel audio controls the remote sound system controls are located at the rear of the steering wheel. Reach behind the wheel to access the switches. The right-hand control is a rocker-type switch with a pushbutton in the center and controls the volume and mode of the sound system. Pushing th...

  • Page 629

    Radio operation pushing the top of the switch will “seek” up for the next listenable station and pushing the bottom of the switch will “seek” down for the next listenable station. The button located in the center of the left-hand control will tune to the next preset station that you have pro- gramme...

  • Page 630

    Nevertheless, the wireless radio will be used in such a manner that the radio is 20 cm or further from the human body. The internal wireless radio operates within guidelines found in radio frequency safety standards and recom- mendations, which reflect the consensus of the scientific community. The ...

  • Page 631

    • if this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • increase the separation between the equipment and r...

  • Page 632

    Key features: • 6.5-inch color touchscreen display with am/fm/ usb/sd card/bluetooth® • bluetooth with integrated voice control • gps navigation (if equipped) get started all you need to control your uconnect® system with your voice are the buttons on your steering wheel. 1. Visit uconnectphone.Com ...

  • Page 633

    3. Speak clearly at a normal pace and volume while facing straight ahead. The microphone is positioned on the rearview mirror and aimed at the driver. 4. Each time you give a voice command, you must first push either the vr or phone button, wait until after the beep, then say your voice command. 5. ...

  • Page 634

    Basic voice commands the basic voice commands below can be given at any point while using your uconnect® system. Push the vr button . After the beep, say ѧ • cancel to stop a current voice session. • help to hear a list of suggested voice commands. • repeat to listen to the system prompts again. Not...

  • Page 635

    Radio use your voice to quickly get to the am, fm or siriusxm satellite radio® stations you would like to hear. (sub- scription or included siriusxm satellite radio® trial required.) push the vr button . After the beep, say ѧ • tune to ninety-five-point-five fm. • tune to satellite channel hits 1. U...

  • Page 636

    Tip: at any time, if you are not sure of what to say or want to learn a voice command, press the vr button and say “help.” the system will provide you with a list of commands. Uconnect® 5.0 radio uconnect® 6.5an radio 634 multimedia.

  • Page 637

    Media uconnect® offers connections via usb port, bluetooth® and auxiliary ports (if equipped). Voice operation is only available for connected usb and ipod® devices. (remote cd player optional and not available on all vehicles.) push the vr button . After the beep, say one of the following commands ...

  • Page 638

    Phone making and answering hands-free phone calls is easy with uconnect®. When the phonebook button is illumi- nated on your touchscreen, your system is ready. Check uconnectphone.Com for mobile phone compatibility and pairing instructions. Push the phone button . After the beep, say one of the foll...

  • Page 639

    Tip: when providing a voice command, push the phone button and say “call,” then pronounce the name exactly as it appears in your phone book. When a contact has multiple phone numbers, you can say “call john smith work.” uconnect® 5.0 phone uconnect® 6.5an phone 11 multimedia 637.

  • Page 640

    Voice text reply uconnect® will announce incoming text messages. Push the phone button and say “listen.” (must have compatible mobile phone paired to uconnect® sys- tem.) 1. Once an incoming text message is read to you, push the phone button . After the beep, say: “reply.” 2. Listen to the uconnect®...

  • Page 641

    Navigation (6.5an) the uconnect® navigation feature helps you save time and become more productive when you know exactly how to get to where you want to go. 1. To enter a destination, push the vr button . After the beep, say: • for the 6.5an uconnect® system, say: “navigate to 800 chrysler drive aub...

  • Page 642

    Uconnect® access* (6.5a/6.5an) an included trial and/or subscription is required to take advantage of the uconnect® access services in the next section of this guide. To register with uconnect® access, push the more button below the 6.5-inch touchscreen to get started. Detailed registration instruct...

  • Page 643

    4. Check your personal inbox for an email from uconnect® access. 5. Click on the link inside the email within 72 hours and complete the easy online registration process to create a personal mopar® owner connect account linked to your vehicle. Mobile app (6.5a/6.5an) securely link your mobile device ...

  • Page 644

    Download the uconnect® access app to a compatible apple® or android® mobile devices. All you need to do is: 1. After registering with uconnect® access, log on to your mopar® owner connect account at moparownerconnect.Com. 2. On the dashboard page, enter your mobile phone number to receive a link to ...

  • Page 645

    Yelp® (6.5a/6.5an) once registered with uconnect® access, you can use your voice to search for the most popular places or things around you. 1. Press the “+ more” button on the faceplate. 2. Press the “all apps” button on the touchscreen. 3. Press the “yelp” button on the touchscreen. 4. Once the ye...

  • Page 646

    Siriusxm travel link™ (6.5a/6.5an) need to find a gas station, view local movie listings, check a sports score or the 5 - day weather forecast? Siriusxm travel link™ is a suite of services that brings a wealth of information right to your uconnect® 6.5an system. Push the vr button . After the beep, ...

  • Page 647

    Additional information © 2015 fca us llc. All rights reserved. Mopar and uconnect are registered trademarks and mopar owner connect is a trademark of fca us llc. Android is a trademark of google inc. Siriusxm and all related marks and logos are trademarks of siriusxm radio inc. Yelp, yelp logo, yelp...

  • Page 649

    Index 12.

  • Page 650

    About your brakes . . . . . . . . . . . . . . . . . . . . . . . .225 abs (anti-lock brake system) . . . . . . . . . . . . . . . .227 adding engine coolant (antifreeze) . . . . . . . . . . . .532 adding fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . .389 adding washer fluid . . . . . . ...

  • Page 651

    Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .534 anti-lock brake system (abs) . . . . . . . . . . . . . . . .227 appearance care . . . . . . . . . . . . . . . . . . . . . . . . .540 arming system (security alarm) . . . . . . . . . . . . . . .50 assist, hill start . . . . . . ....

  • Page 652

    Camera, rear . . . . . . . . . . . . . . . . . . . . . . . . . . . .371 capacities, fluid . . . . . . . . . . . . . . . . . . . . . . . . . .581 caps, filler oil (engine) . . . . . . . . . . . . . . . . . . . . . . . . . . .519 carbon monoxide warning . . . . . . . . . . . . . . .300, 388 car washes...

  • Page 653

    Coin holder . . . . . . . . . . . . . . . . . . . . . . . . . . . . .171 cold weather operation . . . . . . . . . . . . . . . . . . . .312 connector uci . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .624 universal consumer interface (uci) . . . . . . . . . .624 console . . . . . . ...

  • Page 654

    Driver information display (did) instrument cluster . . . . . . . . . . . . . . . . . . . . . .208 oil change . . . . . . . . . . . . . . . . . . . . . . . . . . . .208 driver’s seat back tilt . . . . . . . . . . . . . . . . . . . . . . .67 driving . . . . . . . . . . . . . . . . . . . . . . . . . ....

  • Page 655

    Overheating . . . . . . . . . . . . . . . . . . . . . . . . . . .489 starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .309 engine oil viscosity . . . . . . . . . . . . . . . . . . . . . . .519 engine oil viscosity chart . . . . . . . . . . . . . . . . . . .519 ethanol . . . . . . ....

  • Page 656

    Requirements . . . . . . . . . . . . . . . . . . . . . . . . . .384 specifications . . . . . . . . . . . . . . . . . . . . . . . . . .582 tank capacity . . . . . . . . . . . . . . . . . . . . . . . . . .581 gasoline, clean air . . . . . . . . . . . . . . . . . . . . . . . .385 gasoline (fuel) . . . ...

  • Page 657

    Hood prop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .148 hood release . . . . . . . . . . . . . . . . . . . . . . . . . . . .148 ignition key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41 ignition key removal . . . . . . . . . . . . . . . . . . . . . .492 immo...

  • Page 658

    Unlock liftgate . . . . . . . . . . . . . . . . . . . . . . . . .618 keyless entry system . . . . . . . . . . . . . . . . . . . . . . .31 key, replacement . . . . . . . . . . . . . . . . . . . . . . . . . .40 keys. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31, 41 key, sentry (im...

  • Page 659

    Turn signal . . . . . . . . . . . . . . . . . . . . . . . .101, 303 vanity mirror . . . . . . . . . . . . . . . . . . . . . . . . . .107 loading vehicle . . . . . . . . . . . . . . . . . . . . . . . . . .392 tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .555 locks . . . . . . ....

  • Page 660

    Oil, engine . . . . . . . . . . . . . . . . . . . . . . . . . .517, 582 capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . .581 change interval . . . . . . . . . . . . . . . . . . . . . . . .518 checking . . . . . . . . . . . . . . . . . . . . . . . . . . . . .517 disposal . . . . . . ...

  • Page 661

    Rear parksense system . . . . . . . . . . . . . . . . . . . . .366 rearview mirrors . . . . . . . . . . . . . . . . . . . . . . . . . .83 rear window defroster . . . . . . . . . . . . . . . . . . . . .110 rear wiper/washer. . . . . . . . . . . . . . . . . . . . . . . .110 recorder, event data . . . ...

  • Page 662

    Safety, exhaust gas . . . . . . . . . . . . . . . . . . . . . . . .300 safety information, tire . . . . . . . . . . . . . . . . . . . . .549 safety tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .299 schedule, maintenance . . . . . . . . . . . . . . . . . . . . .507 seat belt adjusta...

  • Page 663

    Sentry key (immobilizer) . . . . . . . . . . . . . . . . . . . .48 sentry key replacement . . . . . . . . . . . . . . . . . . . . .40 service assistance . . . . . . . . . . . . . . . . . . . . . . . . . .11 service contract . . . . . . . . . . . . . . . . . . . . . . . . . . .13 service manuals . . ...

  • Page 664

    Tilt steering column . . . . . . . . . . . . . . . . . . . . . . . .81 time delay, headlight. . . . . . . . . . . . . . . . . . . . . . .99 tip start. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .310 tire and loading information placard . . . . . . .555, 556 tire markings . . . . . ....

  • Page 665

    Cooling system tips . . . . . . . . . . . . . . . . . . . . .413 hitches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .404 minimum requirements . . . . . . . . . . . . . . . . . .407 trailer and tongue weight . . . . . . . . . . . . . . . .406 wiring . . . . . . . . . . . . . . . . . . ...

  • Page 666

    Viscosity, engine oil . . . . . . . . . . . . . . . . . . . . . . .519 warning flasher, hazard . . . . . . . . . . . . . . . . . . . .419 warning, roll over . . . . . . . . . . . . . . . . . . . . . . . . .7 warnings and cautions . . . . . . . . . . . . . . . . . . . . . .7 warranty information . . ...

  • Page 667

    Installation of radio transmitting equipment special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained person- nel. The following must be obs...

  • Page 668

    Renegade o w n e r ’ s m a n u a l 20 15 r enegade 15bu-126-ac third edition rev 2 printed in u.S.A. 2 0 1 5 fca us llc.