1. DL manuals
  2. Jeep
  3. Automobile
  4. 2016 Wrangler
  5. Owner's Manual

Jeep 2016 Wrangler Owner's Manual

Other manuals for 2016 Wrangler: User Manual, User Manual

Summary of 2016 Wrangler

  • Page 1

    Wrangler o w n e r ’ s m a n u a l 2 0 1 6.

  • Page 2

    Vehicles sold in canada with respect to any vehicles sold in canada, the name fca us llc shall be deemed to be deleted and the name fca canada inc. Used in substitution therefore. Driving and alcohol drunken driving is one of the most frequent causes of accidents. Your driving ability can be serious...

  • Page 3: Table Of Contents

    Table of contents section page 1 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 things to know before starting your vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 3 understan...

  • Page 5: Introduction

    Introduction contents 䡵 introduction . . . . . . . . . . . . . . . . . . . . . . . .4 䡵 rollover warning . . . . . . . . . . . . . . . . . . . .5 䡵 how to use this manual . . . . . . . . . . . . . .6 䡵 warnings and cautions . . . . . . . . . . . . . .8 䡵 vehicle identification number . . . . . . . ....

  • Page 6

    Introduction congratulations on selecting your new fca us llc vehicle. Be assured that it represents precision workman- ship, distinctive styling, and high quality - all essentials that are traditional to our vehicles. This is a specialized utility vehicle. It can go places and perform tasks that co...

  • Page 7

    This owner’s manual has been prepared with the assis- tance of service and engineering specialists to acquaint you with the operation and maintenance of your vehicle. It is supplemented by warranty information, and various customer-oriented documents. Please take the time to read these publications ...

  • Page 8

    Failure to use the driver and passenger seat belts pro- vided is a major cause of severe or fatal injury. In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt. Always buckle up. How to use this manual consult the table of contents to determine...

  • Page 9

    1 introduction 7.

  • Page 10

    Warnings and cautions this owner’s manual contains warnings against operating procedures that could result in a collision, bodily injury and/or death. It also contains cautions against procedures that could result in damage to your vehicle. If you do not read this entire owner’s manual, you may miss...

  • Page 11

    Vehicle modifications/alterations warning! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a collision resulting in serious injury or death. 1 introduction 9.

  • Page 13: Contents

    Things to know before starting your vehicle contents 䡵 a word about your keys . . . . . . . . . . . . .14 ▫ ignition key removal . . . . . . . . . . . . . . . . . . .14 ▫ key-in-ignition reminder . . . . . . . . . . . . . . . .16 䡵 sentry key . . . . . . . . . . . . . . . . . . . . . . . . . .16 ▫ r...

  • Page 14

    ▫ to turn off flash lights with lock . . . . . . . . .26 ▫ programming additional transmitters. . . . . . . .26 ▫ transmitter battery replacement . . . . . . . . . . .27 ▫ general information . . . . . . . . . . . . . . . . . . . .28 䡵 remote starting system — if equipped . . . . . . . . . . . . . ....

  • Page 15

    ▫ power windows — if equipped . . . . . . . . . . .43 ▫ wind buffeting . . . . . . . . . . . . . . . . . . . . . . .46 䡵 rear swing gate . . . . . . . . . . . . . . . . . . . . .46 䡵 occupant restraint systems . . . . . . . . . .47 ▫ important safety precautions . . . . . . . . . . . . . .48 ▫ seat ...

  • Page 16

    A word about your keys the authorized dealer that sold you your new vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys. Ask your authorized dealer for these numbers and keep them in a safe place. Ignition key removal 1. Place the shift lever in...

  • Page 17

    Warning! • before exiting a vehicle, always shift the transmis- sion into park, apply the parking brake, and remove the key fob from the vehicle. When leav- ing the vehicle, always lock your vehicle. • never leave children alone in a vehicle, or with access to an unlocked vehicle. • allowing childre...

  • Page 18

    Warning! (continued) • do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death. Caution! An unlocked vehicle is an invitation to thieves. Always remove key from the ignition and lock all doors when leaving the vehicle unattende...

  • Page 19

    Note: a key that has not been programmed is also considered an invalid key, even if it is cut to fit the ignition switch lock cylinder for that vehicle. During normal operation, after turning on the ignition switch, the vehicle security light will turn on for three seconds for a bulb check. If the l...

  • Page 20

    Caution! Always remove the sentry keys from the vehicle and lock all doors when leaving the vehicle unattended. Duplication of keys may be performed at an authorized dealer or by following the customer key programming procedure. This procedure consists of programming a blank key to the vehicle elect...

  • Page 21

    In addition, the vehicle security light will stop flash- ing. To indicate that programming is complete, the vehicle security light will turn on again for three seconds and then turn off. The new sentry key is programmed. The remote key- less entry (rke) transmitter will also be programmed during thi...

  • Page 22

    Vehicle security alarm — if equipped the vehicle security alarm monitors the vehicle doors, swing gate, and ignition for unauthorized operation. While the vehicle security alarm is armed, interior switches for door locks are disabled. The vehicle security alarm provides both audible and visible sign...

  • Page 23

    To disarm the system to disarm the vehicle security alarm, you will need to push the unlock button on the rke transmitter, or turn the ignition switch to the on/run position. If something has triggered the vehicle security alarm in your absence, the horn will sound three times, and the exterior ligh...

  • Page 24

    The lights will fade to off after approximately 30 seconds, or they will immediately fade to off once the ignition switch is turned to on/run from the off position. Note: • the front courtesy overhead console and door cour- tesy lights will turn on if the dimmer control is in the ⬙ dome on ⬙ positio...

  • Page 25

    Note: the line of transmission must not be blocked with metal objects. To unlock the doors and swing gate push and release the rke transmitter unlock button once to unlock the driver’s door only, or twice to unlock all the doors and swing gate. When the rke transmitter unlock button is pushed, the i...

  • Page 26

    2. Continue to hold the rke transmitter lock button for at least four seconds, but not longer than 10 seconds, then push and hold the rke transmitter unlock button. 3. Release both buttons at the same time. 4. Test this feature while outside of the vehicle by pushing the lock/unlock button on the rk...

  • Page 27

    Sound horn on lock this feature will cause the horn to chirp when the doors are locked with the rke transmitter. This feature can be turned on or turned off. To change the current setting, proceed as follows: • for vehicles equipped with the evic, refer to “elec- tronic vehicle information center (e...

  • Page 28

    To turn off flash lights with lock this feature will cause the turn signal lights to flash when the doors are locked or unlocked with the rke transmit- ter. This feature can be turned on or turned off. To change the current setting, proceed as follows: • for vehicles equipped with the evic, refer to...

  • Page 29

    Transmitter battery replacement the recommended replacement battery is cr2032. Note: perchlorate material – special handling may ap- ply. See www.Dtsc.Ca.Gov/hazardouswaste/perchlorate 1. With the rke transmitter buttons facing down, use a flat blade screwdriver to pry the two halves of the rke tran...

  • Page 30

    General information the following regulatory statement applies to all radio frequency (rf) devices equipped in this vehicle: this device complies with part 15 of the fcc rules and with industry canada license-exempt rss standard(s). Operation is subject to the following two conditions: 1. This devic...

  • Page 31

    How to use remote start all of the following conditions must be met before the engine will remote start: • shift lever in park • doors closed • hood closed • hazard switch off • brake switch inactive (brake pedal not pushed) • ignition key removed from ignition switch • battery at an acceptable char...

  • Page 32

    Remote start abort message on electronic vehicle information center (evic) — if equipped the following messages will display in the evic if the vehicle fails to remote start or exits remote start prema- turely: • remote start aborted — door ajar • remote start aborted — hood ajar • remote start abor...

  • Page 33

    Remote start will also cancel if any of the following occur: • the engine stalls or rpm exceeds 2500. • any engine warning lamps come on. • the hood is opened. • the hazard switch is pushed. • the transmission is moved out of park. • the brake pedal is pushed. To exit remote start mode without drivi...

  • Page 34

    2. This device must accept any interference received, including interference that may cause undesired op- eration. Note: changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Doors caution! Careless handling ...

  • Page 35

    Front door removal warning! Do not drive your vehicle on public roads with the doors removed as you will lose the protection that they can provide. This procedure is furnished for use during off-road operation only. 1. Roll down the glass window to prevent any damage. 2. Remove the hinge pin screws ...

  • Page 36

    3. Unplug the wiring harness connector under the instru- ment panel by pushing the tab at the base of the connector and pulling down to disconnect. 4. Unhook the door strap from the body hook. Be careful not to allow the door to swing fully open as the mirror may damage the paint. 5. With the door o...

  • Page 37

    1. Roll down the glass window to prevent any damage. 2. Remove the hinge pin screws from the upper and lower outside hinges (using a #t50 torx head driver). Note: the hinge pin screws and nuts can be stowed in the rear cargo tray located under the rear loadfloor. 3. Slide the front seat(s) fully for...

  • Page 38

    5. Unplug the wiring harness connector. Note: squeeze the tab on the base of the connector. This will unlock the connector tab, allowing the harness to be disconnected. Trim access door connector latched 36 things to know before starting your vehicle.

  • Page 39

    6. Unhook the door strap from the body hook. 7. With the door open, lift the door to clear the hinge pins from their hinges and remove the door. Note: doors are heavy; use caution when removing them. To reinstall the door(s), perform the previous steps in the opposite order. Connector unplugged 2 th...

  • Page 40

    Door locks manual door locks all doors are equipped with an interior rocker-type door lock lever. To lock a door when leaving your vehicle, push the rocker lever forward to the lock position and close the door. To unlock the door, push the rocker lever rearward. Manual door lock (full frame doors) 3...

  • Page 41

    Note: the ignition key that is used to start the vehicle is used to lock or unlock the doors, swing gate, glove compartment, and console storage. Warning! • for personal security reasons and safety in a colli- sion, lock the vehicle doors when you drive, as well as when you park and leave the vehicl...

  • Page 42

    Power door locks — if equipped the power door lock switch is located on each front door panel. Push the switch forward to lock the doors, and rearward to unlock the doors. Warning! • for personal security reasons and safety in a colli- sion, lock the vehicle doors when you drive, as well as when you...

  • Page 43

    Automatic door locks — if equipped the auto door lock feature default condition is enabled. When enabled, the door locks will lock automatically when the vehicle’s speed exceeds 15 mph (24 km/h). The auto door lock feature can be enabled or disabled by your authorized dealer. The auto door lock feat...

  • Page 44

    Child-protection door lock system — rear doors to provide a safer environment for small children riding in the rear seats, the rear doors are equipped with child-protection door lock system. To engage or disengage the child-protection door lock system 1. Open the rear door. 2. Insert the tip of the ...

  • Page 45

    Note: for emergency exit with the system engaged, move the rocker lever rearward (unlocked position), roll down the window and open the door with the outside door handle. Windows power windows — if equipped the power window switches are located on the instru- ment panel below the radio. Push the swi...

  • Page 46

    Note: • for vehicles not equipped with the electronic vehicle information center (evic), the power window switches will remain active for 45 seconds after the ignition switch is turned to the lock position. Open- ing either front door will cancel this feature. • for vehicles equipped with the evic, ...

  • Page 47

    Window lockout switch — four-door models the window lockout switch (located between the front window switches) allows you to disable the rear window switches that are located on the back of the center floor console. To disable the window controls, push the win- dow lockout button downward. To enable...

  • Page 48

    Rear power windows — four-door models the rear passenger window switches are located on the back of the center floor console. Push the switch down- ward to open the window and upward to close the window. Wind buffeting wind buffeting can be described as the perception of pressure on the ears or a he...

  • Page 49

    Note: close the rear flip-up window before attempting to close the swing gate (hard top models only). Caution! Do not press on rear wiper blade when closing the rear flip-up window, as damage to the blade will result. Warning! Driving with the flip-up window open can allow poisonous exhaust gases in...

  • Page 50

    • supplemental restraint systems (srs) air bags • child restraints important safety precautions please pay close attention to the information in this section. It tells you how to use your restraint system properly, to keep you and your passengers as safe as possible. Here are some simple steps you c...

  • Page 51

    8. Do not lean against the door or window. If your vehicle has side air bags, and deployment occurs, the side air bags will inflate forcefully into the space between occupants and the door and occupants could be injured. 9. If the air bag system in this vehicle needs to be modified to accommodate a ...

  • Page 52

    Initial indication if the driver is unbuckled when the ignition switch is first turned to the start or on/run position, an intermit- tent chime will signal for a few seconds. If the driver or outboard front seat passenger (if equipped with outboard front passenger seat beltalert) is unbuckled when t...

  • Page 53

    Seat is folded flat (if equipped). It is recommended that pets be restrained in the rear seat (if equipped) in pet harnesses or pet carriers that are secured by seat belts, and cargo is properly stowed. Beltalert can be activated or deactivated by your autho- rized dealer. Fca us llc does not recomm...

  • Page 54

    Warning! (continued) other passengers, or you can be thrown out of the vehicle. Always be sure you and others in your vehicle are buckled up properly. • it is dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be serious...

  • Page 55

    Warning! (continued) it to your authorized dealer immediately and have it fixed. • a seat belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing inter- nal injuries. Always buckle your seat belt into the buckle nea...

  • Page 56

    Lap/shoulder belt operating instructions 1. Enter the vehicle and close the door. Sit back and adjust the seat. 2. The seat belt latch plate is above the back of the front seat, and next to your arm in the rear seat (for vehicles equipped with a rear seat). Grasp the latch plate and pull out the sea...

  • Page 57

    4. Position the lap belt so that it is snug and lies low across your hips, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug seat belt reduces the risk of sliding...

  • Page 58

    Stowed position. If necessary, slide the latch plate down the webbing to allow the seat belt to retract fully. Rear center lap/shoulder belt retractor lockout this feature is designed to lock the retractor whenever the rear seatback is not fully latched. This prevents someone from wearing the rear c...

  • Page 59

    2. At about 6 to 12 in (15 to 30 cm) above the latch plate, grasp and twist the seat belt webbing 180 degrees to create a fold that begins immediately above the latch plate. 3. Slide the latch plate upward over the folded webbing. The folded webbing must enter the slot at the top of the latch plate....

  • Page 60

    Note: the adjustable upper shoulder belt anchorage is equipped with an easy up feature. This feature allows the shoulder belt anchorage to be adjusted in the upward position without pushing or squeezing the release but- ton. To verify the shoulder belt anchorage is latched, pull downward on the shou...

  • Page 61

    Seat belts and pregnant women seat belts must be worn by all occupants including pregnant women: the risk of injury in the event of an accident is reduced for the mother and the unborn child if they are wearing a seat belt. Position the lap belt snug and low below the abdomen and across the strong b...

  • Page 62

    The pretensioners are triggered by the occupant re- straint controller (orc). Like the air bags, the preten- sioners are single use items. A deployed pretensioner or a deployed air bag must be replaced immediately. Energy management feature this vehicle has a seat belt system with an energy manageme...

  • Page 63

    If the passenger seating position is equipped with an alr and is being used for normal usage, only pull the seat belt webbing out far enough to comfortably wrap around the occupant’s mid-section so as to not activate the alr. If the alr is activated, you will hear a clicking sound as the seat belt r...

  • Page 64

    Warning! (continued) 12 years or younger, including a child in a rear- facing child restraint. • only use a rear-facing child restraint in a vehicle with a rear seat. How to engage the automatic locking mode 1. Buckle the combination lap and shoulder belt. 2. Grasp the shoulder portion and pull down...

  • Page 65

    Supplemental restraint system (srs) air bag system components your vehicle may be equipped with the following air bag system components: • occupant restraint controller (orc) • air bag warning light • steering wheel and column • instrument panel • knee impact bolsters • advanced front air bags • sup...

  • Page 66

    Warning! • being too close to the steering wheel or instrument panel during advanced front air bag deployment could cause serious injury, including death. Air bags need room to inflate. Sit back, comfortably extending your arms to reach the steering wheel or instrument panel. • never place a rear-fa...

  • Page 67

    Advanced front air bag features the advanced front air bag system has multistage driver and front passenger air bags. This system provides output appropriate to the severity and type of collision as determined by the occupant restraint controller (orc), which may receive information from the front i...

  • Page 68

    Warning! (continued) some collisions, air bags won’t deploy at all. Al- ways wear your seat belts even though you have air bags. Advanced front air bag operation advanced front air bags are designed to provide addi- tional protection by supplementing the seat belts. Ad- vanced front air bags are not...

  • Page 69

    Knee impact bolsters the knee impact bolsters help protect the knees of the driver and front passenger, and position the front occu- pants for improved interaction with the advanced front air bags. Warning! • do not drill, cut, or tamper with the knee impact bolsters in any way. • do not mount any a...

  • Page 70

    Through the seat seam into the space between the occupant and the door. The sab moves at a very high speed and with such a high force that it could injure occupants if they are not seated properly, or if items are positioned in the area where the sab inflates. Children are at an even greater risk of...

  • Page 71

    Seat belts (and child restraints where appropriate) are necessary for your protection in all collisions. They also help keep you in position, away from an inflating sab. To get the best protection from the sabs, occupants must wear their seat belts properly and sit upright with their backs against t...

  • Page 72

    If you do have a collision which deploys the air bags, any or all of the following may occur: • the air bag material may sometimes cause abrasions and/or skin reddening to the occupants as the air bags deploy and unfold. The abrasions are similar to fric- tion rope burns or those you might get slidi...

  • Page 73

    • after any collision, the vehicle should be taken to an authorized dealer immediately. Enhanced accident response system in the event of an impact, if the communication network remains intact, and the power remains intact, depending on the nature of the event, the orc will determine whether to have...

  • Page 74

    The off position or in the acc position, the air bag system is not on and the air bags will not inflate. The orc contains a backup power supply system that may deploy the air bags even if the battery loses power or it becomes disconnected prior to deployment. The orc turns on the air bag warning lig...

  • Page 75

    Warning! Ignoring the air bag warning light in your instrument panel could mean you won’t have the air bags to protect you in a collision. If the light does not come on as a bulb check when the ignition is first placed in the on position, and stays on after you start the vehicle, or if it comes on a...

  • Page 76

    Warning! (continued) authorized dealer. Only manufacturer approved seat accessories may be used. If it is necessary to modify the air bag system for persons with dis- abilities, contact your authorized dealer. Event data recorder (edr) this vehicle is equipped with an event data recorder (edr). The ...

  • Page 77

    In addition to the vehicle manufacturer, other parties, such as law enforcement, that have the special equip- ment, can read the information if they have access to the vehicle or the edr. Child restraints everyone in your vehicle needs to be buckled up at all times, including babies and children. Ev...

  • Page 78

    Before buying any restraint system, make sure that it has a label certifying that it meets all applicable safety standards. You should also make sure that you can install it in the vehicle where you will use it. Note: • for additional information, refer to www.Seatcheck.Org or call 1-866-732-8243. •...

  • Page 79

    Child size, height, weight or age recommended type of child restraint larger children children who have out-grown their forward-facing child restraint, but are too small to properly fit the vehicle’s seat belt belt positioning booster seat and the ve- hicle seat belt, seated in the rear seat of the ...

  • Page 80

    Warning! • never place a rear-facing child restraint in front of an air bag. A deploying passenger advanced front air bag can cause death or serious injury to a child 12 years or younger, including a child in a rear- facing child restraint. • only use a rear-facing child restraint in a vehicle with ...

  • Page 81

    Warning! (continued) directions exactly when installing an infant or child restraint. • after a child restraint is installed in the vehicle, do not move the vehicle seat forward or rearward because it can loosen the child restraint attach- ments. Remove the child restraint before adjusting the vehic...

  • Page 82

    5. Can the child stay seated like this for the whole trip? If the answer to any of these questions was “no,” then the child still needs to use a booster seat in this vehicle. If the child is using the lap/shoulder belt, check seat belt fit periodically and make sure the seat belt buckle is latched. ...

  • Page 83

    Recommendations for attaching child restraints restraint type combined weight of the child + child restraint use any attachment method shown with an “x” below latch – lower anchors only seat belt only latch – lower anchors + top tether anchor seat belt + top tether anchor rear-facing child restraint...

  • Page 84

    Lower anchors and tethers for children (latch) restraint system your vehicle is equipped with the child restraint anchor- age system called latch, which stands for lower anchors and tethers for children. The latch system has three vehicle anchor points for installing latch- equipped child seats. The...

  • Page 85

    Latch positions for installing child restraints in this vehicle latch positions (two-door models) lower anchorage symbol 2 anchorages per seating position top tether anchorage symbol latch positions (four-door models) lower anchorage symbol 2 anchorages per seating position top tether anchorage symb...

  • Page 86

    What is the weight limit (child’s weight + weight of the child restraint) for using the latch anchorage system to attach the child restraint? 65 lbs (29.5 kg) use the latch anchorage system until the combined weight of the child and the child restraint is 65 lbs (29.5 kg). Use the seat belt and teth...

  • Page 87

    Can two child restraints be attached using a common lower latch anchorage? No never “share” a latch anchorage with two or more child restraints. If the center position does not have dedicated latch lower anchorages, use the seat belt to in- stall a child seat in the center position next to a child s...

  • Page 88

    Locating the latch anchorages the lower anchorages are round bars that are found at the rear of the seat cushion where it meets the seatback, below the anchorage sym- bols on the seatback. They are just visible when you lean into the rear seat to install the child restraint. You will easily feel the...

  • Page 89

    Locating tether anchorages there are tether strap anchorages behind each rear seating position located on the back of the seat, near the floor. Latch anchorages (four-door models) tether strap anchorages (two-door models) 2 things to know before starting your vehicle 87.

  • Page 90

    Latch-compatible child restraint systems will be equipped with a rigid bar or a flexible strap on each side. Each will have a hook or connector to attach to the lower anchorage and a way to tighten the connection to the anchorage. Forward-facing child restraints and some rear-facing child restraints...

  • Page 91

    Warning! Never use the same lower anchorage to attach more than one child restraint. If you are installing latch- compatible child restraints next to each other, you must use the seat belt for the center position. You can then use either the latch anchors or the vehicle’s seat belt for installing ch...

  • Page 92

    3. Attach the lower hooks or connectors of the child restraint to the lower anchorages in the selected seat- ing position. 4. If the child restraint has a tether strap, connect it to the top tether anchorage. See the section “installing child restraints using the top tether anchorage” for direc- tio...

  • Page 93

    Warning! • improper installation of a child restraint to the latch anchorages can lead to failure of the re- straint. The child could be badly injured or killed. Follow the child restraint manufacturer’s directions exactly when installing an infant or child restraint. • child restraint anchorages ar...

  • Page 94

    Lap/shoulder belt systems for installing child restraints in this vehicle • alr = switchable automatic locking retractor • top tether anchorage symbol two-door models four-door models 92 things to know before starting your vehicle.

  • Page 95

    What is the weight limit (child’s weight + weight of the child re- straint) for using the tether anchor with the seat belt to attach a forward facing child restraint? Weight limit of the child restraint always use the tether anchor when using the seat belt to install a for- ward facing child restrai...

  • Page 96

    Installing a child restraint with a switchable automatic locking retractor (alr) 1. Place the child seat in the center of the seating position. For some second row seats, you may need to recline the seat and/or raise the head restraint to get a better fit. If the rear seat can be moved forward and r...

  • Page 97

    Strap. See the section “installing child restraints using the top tether anchorage” for directions to attach a tether anchor. 9. Test that the child restraint is installed tightly by pulling back and forth on the child seat at the belt path. It should not move more than 1 inch (25.4 mm) in any direc...

  • Page 98

    Tether anchorage for that seating position, move the child restraint to another position in the vehicle if one is available. 2. Route the tether strap to provide the most direct path for the strap between the anchor and the child seat. If your vehicle is equipped with adjustable rear head restraints...

  • Page 99

    4. Remove slack in the tether strap according to the child restraint manufacturer’s instructions. Warning! • an incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchorage position directly behind the child seat to secure a child res...

  • Page 100

    Transporting pets air bags deploying in the front seat could harm your pet. An unrestrained pet will be thrown about and possibly injured, or injure a passenger during panic braking or in a collision. Pets should be restrained in the rear seat in pet harnesses or pet carriers that are secured by sea...

  • Page 101

    Note: a new engine may consume some oil during its first few thousand miles (kilometers) of operation. This should be considered a normal part of the break-in and not interpreted as an indication of difficulty. Safety tips transporting passengers never transport passengers in the cargo area. Warning...

  • Page 102

    Exhaust gas warning! Exhaust gases can injure or kill. They contain carbon monoxide (co), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing (co), follow these safety tips: • do not run the engine in a closed garage or in confined...

  • Page 103

    Safety checks you should make inside the vehicle seat belts inspect the seat belt system periodically, checking for cuts, frays, and loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Front seat belt assemblies must be replaced after a collision. Rear s...

  • Page 104

    Defroster check operation by selecting the defrost mode and place the blower control on high speed. You should be able to feel the air directed against the windshield. See your autho- rized dealer for service if your defroster is inoperable. Floor mat safety information always use floor mats designe...

  • Page 105

    Warning! (continued) • always make sure that objects cannot fall into the driver footwell while the vehicle is moving. Ob- jects can become trapped under the brake pedal and accelerator pedal causing a loss of vehicle control. • if required, mounting posts must be properly in- stalled, if not equipp...

  • Page 106

    Lights have someone observe the operation of brake lights and exterior lights while you work the controls. Check turn signal and high beam indicator lights on the instrument panel. Door latches check for proper closing, latching, and locking. Fluid leaks check area under vehicle after overnight park...

  • Page 107: Contents

    Understanding the features of your vehicle contents 䡵 mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . .111 ▫ inside day/night mirror — if equipped . . . . .111 ▫ outside mirrors . . . . . . . . . . . . . . . . . . . . . .112 ▫ automatic dimming mirror — if equipped . . .112 ▫ power mir...

  • Page 108

    ▫ delete/erase “all” uconnect phonebook entries . . . . . . . . . . . . . . . . . . . . . . . . . . . . .124 ▫ list all names in the uconnect phonebook . . .124 ▫ phone call features . . . . . . . . . . . . . . . . . . .125 ▫ uconnect phone features . . . . . . . . . . . . . . . .128 ▫ advanced phon...

  • Page 109

    䡵 to open and close the hood . . . . . . . . .167 䡵 lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . .168 ▫ multifunction lever . . . . . . . . . . . . . . . . . . . .168 ▫ headlights and parking lights . . . . . . . . . . . .169 ▫ automatic headlights — if equipped . . . . . . .169 ▫ ...

  • Page 110

    ▫ to vary the speed setting . . . . . . . . . . . . . . .183 ▫ to accelerate for passing . . . . . . . . . . . . . . .184 䡵 electrical power outlets . . . . . . . . . . .185 䡵 power inverter — if equipped . . . . . . . .189 䡵 cupholders . . . . . . . . . . . . . . . . . . . . . . . .191 ▫ front cuph...

  • Page 111

    ▫ front panel(s) installation with rear hard top removed . . . . . . . . . . . . . . . . . . . . . . . . . . .214 ▫ rear hard top removal . . . . . . . . . . . . . . . .214 ▫ rear hard top installation . . . . . . . . . . . . . . .217 䡵 door frame. . . . . . . . . . . . . . . . . . . . . . . . .218 ...

  • Page 112

    䡵 folding windshield . . . . . . . . . . . . . . . . .295 ▫ lowering the windshield and removing side bars . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .296 ▫ raising the windshield and replacing side bars . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .300 䡵 rear window ...

  • Page 113

    Mirrors inside day/night mirror — if equipped the mirror head can be adjusted up, down, left, and right for various drivers. The mirror should be adjusted to center on the view through the rear window. Headlight glare from vehicles behind you can be reduced by moving the small control under the mirr...

  • Page 114

    Outside mirrors to receive maximum benefit, adjust the outside mirror(s) to center on the adjacent lane of traffic with a slight overlap of the view obtained on the inside mirror. Warning! Vehicles and other objects seen in the passenger side convex mirror will look smaller and farther away than the...

  • Page 115

    Caution! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror. Apply the solution onto a clean cloth and wipe the mirror clean. Power mirrors — if equipped the power mirror switch is located on the center of the instrument panel, below the climate...

  • Page 116

    After selecting a mirror, move the knob in the same direction you want the mirror to move. Use the center off position to guard against accidentally moving a mirror position. Heated mirrors — if equipped these mirrors are heated to melt frost or ice. This feature can be activated whenever you turn o...

  • Page 117

    Uconnect phone — if equipped uconnect phone is a voice-activated, hands-free, in- vehicle communications system. Uconnect phone allows you to dial a phone number with your mobile phone using simple voice commands (e.G., “call” ѧ “mike” ѧ “work” or “dial” ѧ “248-555-1212”). Your mobile phone’s audio ...

  • Page 118

    Linked (or paired) mobile phone can be used with the system at a time. The system is available in english, spanish, or french languages. Warning! Always drive safely with your hands on the wheel. You have full responsibility and assume all risks related to the use of the uconnect features and applic...

  • Page 119

    Actual button location may vary with the ra- dio. The individual buttons are described in the “operation” section. The uconnect phone can be used with any hands-free profile certified bluetooth mobile phone. See the uconnect website for supported phones. Refer to your mobile service provider or the ...

  • Page 120

    Part of the command when you are asked for it. For example, you can use the compound form voice com- mand “phonebook new entry,” or you can break the compound form command into two voice commands: “phonebook” and “new entry.” please remember, the uconnect phone works best when you talk in a normal c...

  • Page 121

    • after the “ready” prompt and the following beep, say “setup phone pairing.” • when prompted, after the beep, say “pair a phone” and follow the audible prompts. • you will be asked to say a four-digit personal identi- fication number (pin), which you will later need to enter into your mobile phone....

  • Page 122

    • the uconnect phone will confirm the phone number and then dial. The number will appear in the display of certain radios. Call by saying a name • push the phone button to begin. • after the “ready” prompt and the following beep, say “call.” • the system will prompt you to say the name of the person...

  • Page 123

    • automatic download and update, if supported, begins as soon as the bluetooth wireless phone connection is made to the uconnect phone, for example, after you start the vehicle. • a maximum of 1,000 entries per phone will be down- loaded and updated every time a phone is connected to the uconnect ph...

  • Page 124

    • when prompted, enter the number designation (e.G., “home,” “work,” “mobile,” or “other”). This will allow you to store multiple numbers for each phone- book entry, if desired. • when prompted, recite the phone number for the phonebook entry that you are adding. After you are finished adding an ent...

  • Page 125

    Note: • editing names in the phonebook is recommended when the vehicle is not in motion. • automatic downloaded phonebook entries cannot be deleted or edited. “phonebook edit” can be used to add another phone number to a name entry that already exists in the phone- book. For example, the entry john ...

  • Page 126

    Note: automatic downloaded phonebook entries can- not be deleted or edited. Delete/erase “all” uconnect phonebook entries to delete, or erase all uconnect phonebook entries using voice command: 1. Push the phone button to begin. 2. After the “ready” prompt and the following beep, say “phonebook eras...

  • Page 127

    Phone call features the following features can be accessed through the uconnect phone if the feature(s) are available on your mobile service plan. For example, if your mobile service plan provides three-way calling, this feature can be accessed through the uconnect phone. Check with your mobile serv...

  • Page 128

    First call, refer to “toggling between calls” in this section. To combine two calls, refer to “conference call” in this section. Place/retrieve a call from hold to put a call on hold, push the phone button until you hear a single beep. This indicates that the call is on hold. To bring the call back ...

  • Page 129

    Call termination to end a call in progress: 1. Momentarily push the phone button. • only the active call(s) will be terminated and if there is a call on hold, it will become the new active call. If the active call is terminated by the phone far end, a call on hold may not become active automatically...

  • Page 130

    2. After the ignition is cycled to off, a call can continue on the uconnect phone for a certain duration, after which the call is automatically transferred from the uconnect phone to the mobile phone. 3. An active call is automatically transferred to the mobile phone after the ignition is cycled to ...

  • Page 131

    • after the “ready” prompt and the following beep, say “emergency” and the uconnect phone will instruct the paired mobile phone to call the emergency number. This feature is supported in the u.S., canada, and mexico. Note: • the emergency number dialed is based on the country where the vehicle is pu...

  • Page 132

    Note: you should program the desired towing assis- tance phone number using the voice command system. To do this, push the phone button and say “setup,” followed by “towing assistance.” when prompted say 1-800-521-2779 for u.S./canada, say 55-14-3454 for mexico city and 1-800-712-3040 for outside me...

  • Page 133

    Used for navigating through an automated customer service center menu structure, and to leave a number on a pager. You can also send stored uconnect phonebook entries as tones for fast and easy access to voice mail and pager entries. To use this feature, dial the number you wish to call and then pus...

  • Page 134

    To turn confirmation prompts on or off using voice command: 1. Push the phone button to begin. 2. After the “ready” prompt and the following beep, say: • “setup confirmations prompts on” • “setup confirmations prompts off” phone and network status indicators if available on the radio and/or on a pre...

  • Page 135

    Mute/un-mute (mute on/off) when you mute the uconnect phone, you will still be able to hear the conversation coming from the other party, but the other party will not be able to hear you. To mute the uconnect phone: • push the voice command button. • following the beep, say “mute.” to un-mute the uc...

  • Page 136

    • when prompted, say “list phones.” • the uconnect phone will play the phone names of all paired mobile phones in order from the highest to the lowest priority. To “select” or “delete” a paired phone being announced, push the voice command but- ton and say “select” or “delete.” also, see the next tw...

  • Page 137

    • you can also push the voice command button at any time while the list is being played, and then choose the phone you wish to delete. Things you should know about your uconnect phone uconnect phone tutorial to hear a brief tutorial of the system features, push the phone button and say “uconnect tut...

  • Page 138

    Reset to reset all settings using voice command: 1. Push the phone button. 2. After the “ready” prompt and the following beep, say “setup,” then “reset.” • this will delete all phone pairing, phone book en- tries, and other settings in all language modes. The system will prompt you before resetting ...

  • Page 139

    Note: • even though the system is designed for users speaking in north american english, french, and spanish ac- cents, the system may not always work for some. • when navigating through an automated system such as voice mail, or when sending a page, at the end of speaking the digit string, make sur...

  • Page 140

    • performance, such as audio clarity, echo, and loudness to a large degree rely on the phone and network, and not the uconnect phone • echo at the phone far end can sometimes be reduced by lowering the in-vehicle audio volume recent calls if your phone supports “automatic phonebook down- load,” ucon...

  • Page 141

    Send messages: you can send messages using uconnect phone. To send a new message: • push the phone button. • after the “ready” prompt and the following beep, say “sms send” or “send messages.” • you can either say the message you wish to send or say “list messages.” there are 20 preset messages. To ...

  • Page 142

    11. See you in 15 minutes 12. I am on my way 13. I’ll be late 14. Are you there yet? 15. Where are we meeting? 16. Can this wait? 17. Bye for now 18. When can we meet? 19. Send number to call 20. Start without me turn sms incoming announcement on/off turning the sms incoming announcement off will st...

  • Page 143

    3 understanding the features of your vehicle 141.

  • Page 144

    142 understanding the features of your vehicle.

  • Page 145

    3 understanding the features of your vehicle 143.

  • Page 146

    Voice commands primary alternate (s) zero one two three four five six seven eight nine star (*) plus (+) pound (#) add location primary alternate (s) all call cancel confirmation prompts continue delete dial download edit emergency english erase all espanol francais help 144 understanding the featur...

  • Page 147

    Primary alternate (s) home language list names list phones mobile mute mute off new entry no other pair a phone phone pairing pairing phonebook phone book previous record again primary alternate (s) redial return to main menu return or main menu select phone select send set up phone settings or phon...

  • Page 148

    General information this device complies with part 15 of the fcc rules and rss 210 of industry canada. Operation is subject to the following conditions: • changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment....

  • Page 149

    Warning! Any voice commanded system should be used only in safe driving conditions following all applicable laws, including laws regarding phone use. Your at- tention should be focused on safely operating the vehicle. Failure to do so may result in a collision causing serious injury or death. When y...

  • Page 150

    To hear the first available menu, push the voice com- mand button and say “help” or “main menu.” commands the voice command system understands two types of commands, universal commands and local commands. Universal commands are available at all times. Local commands are available if the supported ra...

  • Page 151

    • “bluetooth streaming” (to switch to bluetooth stream- ing mode) • “memo” (to switch to the memo recorder) • “system setup” (to switch to system setup) radio am to switch to the am band, say “am” or “radio am.” in this mode, you may say the following commands: • “frequency #” (to change the frequen...

  • Page 152

    • “previous channel” (to select the previous channel) • “list channel” (to hear a list of available channels) • “select name” (to say the name of a channel) • “menu radio” (to switch to the radio menu) • “main menu” (to switch to the main menu) disc mode to switch to the disc mode, say “disc.” in th...

  • Page 153

    Memo mode to switch to the voice recorder mode, say “memo.” in this mode, you may say the following commands: • “new memo” (to record a new memo) — during the recording, you may push the voice command but- ton to stop recording. You proceed by saying one of the following commands: – “save” (to save ...

  • Page 154

    • “tutorial” • “voice training” note: keep in mind that you have to push the voice command button first and wait for the beep before speaking the “barge in” commands. Voice training for users experiencing difficulty with the system recog- nizing their voice commands or numbers the uconnect voice “vo...

  • Page 155

    Warning! (continued) • do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. In a collision, people riding in these areas are more likely to be seriously injured or killed. • be sure everyone in your vehicle is in a seat and using a seat belt properl...

  • Page 156

    Warning! • adjusting a seat while driving may be dangerous. Moving a seat while driving could result in loss of control which could cause a collision and serious injury or death. • seats should be adjusted before fastening the seat belts and while the vehicle is parked. Serious injury or death could...

  • Page 157

    Warning! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt, which could result in serious injury or death. Front passenger easy entry seat — two-door models pull upward on the recline lever (to...

  • Page 158

    To return the seat to a sitting position, rotate the seatback upright until it locks and push the seat rearward until the track locks. Note: • the front passenger seats have a track memory, which returns the seat to just past the halfway point of the track regardless of its original position. • the ...

  • Page 159

    Rotate the entire seat assembly toward the instrument panel. Passenger seat in addition to easy entry, the front passenger seat is also equipped with tip n’ slide. This feature allows for easier entry for rear passengers. Recline lever tip n’ slide 3 understanding the features of your vehicle 157.

  • Page 160

    Pull upward on the recline lever and slide the entire seat forward (easy entry). With the seat forward, pull the entire seat assembly toward the instrument panel. Easy entry lever tip n’ slide 158 understanding the features of your vehicle.

  • Page 161

    Heated seats — if equipped on some models, the front driver and passenger seats may be equipped with heaters in both the seat cushions and seatbacks. There are two heated seat switches that allow the driver and passenger to operate the seats independently. The controls for each seat are located on a...

  • Page 162

    Warning! (continued) when using the seat heater. It may cause burns even at low temperatures, especially if used for long periods of time. • do not place anything on the seat or seatback that insulates against heat, such as a blanket or cushion. This may cause the seat heater to overheat. Sitting in...

  • Page 163

    Up. To reinstall the head restraint, put the head restraint posts into the holes and push downward. Then adjust it to the appropriate height. Warning! • a loose head restraint thrown forward in a colli- sion or hard stop could cause serious injury or death to occupants of the vehicle. Always securel...

  • Page 164

    Two head restraint guides and pull upward on the head restraint. Replace the head restraint before driving the vehicle with passengers in the rear seat. To replace the head restraint, insert the head restraint rods into the guides and push downward on the head restraint until locked. Refer to “occup...

  • Page 165

    Removing the rear seat — two-door models note: • prior to folding the rear seat, it may be necessary to reposition the front seats. • be sure that the front seats are fully upright and positioned forward. This will allow the rear seat to fold down easily. 1. Lift the seatback release lever and fold ...

  • Page 166

    Warning! Do not drive the vehicle with the seat in the forward tumble position. The seat must be latched to all floor attachments when the vehicle is in motion. 3. Push down on the release bar on each side, and pull the seat out and away from the lower bracket. 4. Remove the seat from the vehicle. F...

  • Page 167

    Warning! • it is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • be...

  • Page 168

    • be sure that the front seats are fully upright and positioned forward. This will allow the rear seat to fold down easily. Warning! • it is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injur...

  • Page 169

    To raise the rear seat raise the seatback and lock it into place. If interference from the cargo area prevents the seatback from fully locking, you will have difficulty returning the seat to its proper position. Note: if the rear seatback is not fully latched, the center shoulder belt will not be ab...

  • Page 170

    Down slightly on the hood before pushing the safety latch. Insert the support rod into the slot on the hood. To close the hood, remove the support rod from the hood panel and place it in the retaining clip. Lower the hood slowly. Secure both of the hood latches. Warning! Be sure the hood is fully la...

  • Page 171

    Headlights and parking lights turn the end of the multifunction lever to the first detent for parking light operation. Turn to the second detent for headlight operation. Automatic headlights — if equipped this system automatically turns the headlights on or off according to ambient light levels. To ...

  • Page 172

    Note: the engine must be running before the head- lights will turn on in the automatic mode. Turn signals move the multifunction lever up or down and the arrows on each side of the instrument cluster flash to show proper operation of the front and rear turn signal lights. Headlight switch turn signa...

  • Page 173

    Note: • if either light remains on and does not flash, or there is a very fast flash rate, check for a defective outside light bulb. If an indicator fails to light when the lever is moved, it would suggest that the indicator bulb is defective. • a tone will chime if the turn signals are left on for ...

  • Page 174

    Note: the fog lights will only operate with the parking lights or the headlights on low beam. Selecting high beam headlights will turn off the fog lights. Instrument panel dimmer rotate the center portion of the lever to the extreme bottom position to fully dim the instrument panel lights and preven...

  • Page 175

    Note: the daytime running light on the same side of the vehicle as the active turn signal will turn off auto- matically when a turn signal is in operation and turn on again when the turn signal is not operating. Interior lights the overhead light will turn on when a door is opened. It may also be tu...

  • Page 176

    Cargo lamp the courtesy and dome lights will turn on when the front doors are opened, by rotating the control for the dimmer switch on the multifunction lever fully upward, or if equipped, when the unlock button is pushed on the remote keyless entry (rke) transmitter. The sports bar reading lights (...

  • Page 177

    The rear cargo light may be turned on by pushing the lens. Push the lens a second time to turn the light off. When a door is open and the interior lights are on, rotating the dimmer control to the extreme bottom posi- tion will cause all the interior lights to turn off. This is also known as the “pa...

  • Page 178

    Windshield wipers and washers the windshield wiper/washer control lever is located on the right side of the steering column. The front wipers are operated by rotating a switch, located at the end of the lever. For information on using the rear window wiper/ washer, refer to “rear window features” in...

  • Page 179

    Windshield wiper operation rotate the end of the lever upward to the second detent past the intermittent settings for low-speed wiper opera- tion. Rotate the end of the lever upward to the third detent past the intermittent settings for high-speed wiper operation. Front wiper control 3 understanding...

  • Page 180

    Caution! In cold weather, always turn off the wiper switch and allow the wipers to return to the park position before turning off the engine. If the wiper switch is left on and the wipers freeze to the windshield, damage to the wiper motor may occur when the vehicle is restarted. Intermittent wiper ...

  • Page 181

    Windshield washers to use the washer, pull the lever toward you and hold while spray is desired. If the lever is pulled while in the delay range, the wiper will start and continue to operate for two or three wipe cycles after the lever is released, and then resume the intermittent interval previousl...

  • Page 182

    Tilt steering column this feature allows you to tilt the steering column upward or downward. The tilt lever is located on the steering column, below the turn signal lever. Push down on the lever to unlock the steering column. With one hand firmly on the steering wheel, move the steering column up or...

  • Page 183

    Warning! Do not adjust the steering column while driving. Adjusting the steering column while driving or driv- ing with the steering column unlocked, could cause the driver to lose control of the vehicle. Failure to follow this warning may result in serious injury or death. Electronic speed control ...

  • Page 184

    Note: in order to ensure proper operation, the elec- tronic speed control system has been designed to shut down if multiple speed control functions are operated at the same time. If this occurs, the electronic speed control system can be reactivated by pushing the electronic speed control on/off but...

  • Page 185

    To deactivate a soft tap on the brake pedal, pushing the cancel button, or normal brake pressure while slowing the vehicle will deactivate the electronic speed control with- out erasing the set speed from memory. Pushing the on/off button or turning the ignition switch off erases the set speed from ...

  • Page 186

    • if the button is continually pushed, the set speed will continue to increase until the button is released, then the new set speed will be established. To decrease speed when the electronic speed control is set, you can de- crease speed by pushing the set (-) button. The drivers preferred units can...

  • Page 187

    Note: the electronic speed control system maintains speed up and down hills. A slight speed change on moderate hills is normal. On steep hills, a greater speed loss or gain may occur so it may be preferable to drive without electronic speed control. Warning! Electronic speed control can be dangerous...

  • Page 188

    When the optional cigar lighter heating element is used in the power outlet, it heats when pushed in and pops out automatically when ready for use. To preserve the heat- ing element, do not hold the lighter in the heating position. A second power outlet is located inside the center console and is po...

  • Page 189

    On vehicles equipped with a rear subwoofer, there is a third power outlet located in the right rear cargo area. Rear power outlet — if equipped power outlet fuse locations 1 — m36 fuse 20 a yellow power outlet console bin 2 — m6 fuse 20 a yellow cigar lighter instrument panel 3 — m7 fuse 20 a yellow...

  • Page 190

    Warning! To avoid serious injury or death: • only devices designed for use in this type of outlet should be inserted into any 12 volt outlet. • do not touch with wet hands. • close the lid when not in use and while driving the vehicle. • if this outlet is mishandled, it may cause an electric shock a...

  • Page 191

    Caution! (continued) • power outlets are designed for accessory plugs only. Do not hang any type of accessory or acces- sory bracket from the plug. Power inverter — if equipped there is a 115 volt, 150 watt inverter outlet located on the front of the center console to convert dc current to ac curren...

  • Page 192

    May have to be reset manually. To reset the inverter manually push the power inverter button off and on. To avoid overloading the circuit, check the power ratings on electrical devices prior to using the inverter. The power inverter switch is located on the instrument panel below the climate control...

  • Page 193

    Cupholders front cupholders the front cupholders are located in the center console. Rear cupholders the rear cupholders are located on the back of the center console. Front cupholders rear cupholders 3 understanding the features of your vehicle 191.

  • Page 194

    Storage glove compartment the lockable glove compartment is located on the pas- senger side of the lower instrument panel. Pull outward on the handle/latch to open the glove compartment. Console storage compartment to lock or unlock the storage compartment, insert the ignition key and turn. To open ...

  • Page 195

    There is an extra storage area underneath the console lid. The console lid has an integrated paper clip feature that can hold small items. Rear storage compartment — if equipped the rear cargo area storage compartment cover is held by a spring-loaded latch. In order to remove the rear storage compar...

  • Page 196

    3. Open the rear compartment cover. Dual top — two-door models — if equipped if your vehicle is equipped with a dual top, you must remove one of the tops from the vehicle. If the soft top is removed, the pivot brackets must also be removed from the sport bar. The soft top was installed at the factor...

  • Page 197

    2. Remove the hard top. Refer to “freedom top three- piece modular hard top — front/rear panel re- moval” in this section. 3. Remove the soft top bow assembly pivot bracket screws (two per side) using a #t30 torx head driver. 4. Disconnect the knuckles from the left and right metal pivot brackets. R...

  • Page 198

    5. Unzip the zipper on the sport bar cover to expose the pivot brackets. Remove the brackets using a #t30 torx head driver. Recover and re-zip the sports bar cover. Store the pivot brackets and screws in a safe place. 6. Reinstall the hard top. Refer to “freedom top three- piece modular hard top — f...

  • Page 199

    B. Lay the soft top into the rear of the vehicle with the bows pointing forward and the curved portion of the bows facing upward. C. Reattach the knuckles onto the metal pivot brackets. Note: to aid in reattaching the knuckles, you may carefully tap on the knuckles using a rubber mallet. D. Screw th...

  • Page 200

    Caution! Do not overtighten the screws. You can strip the screws if they are overtightened. 5. Remove the swing gate bar (black metal bar for bottom of rear window) and set aside. Note: be sure the wire harness in the left rear corner is not tangled in the soft top bows before you lift the top. 6. U...

  • Page 201

    Mandatory to prevent any possible wear and tear on the soft top. Your vehicle warranty will not cover damage resulting from both tops remaining on the vehicle at the same time for extended periods of time. Removing the soft top — four-door models 1. Locate and remove the two boxes that contain the f...

  • Page 202

    5. The tether strap must be hooked onto the pivot bracket prior to removal of soft top from vehicle (both sides). 200 understanding the features of your vehicle.

  • Page 203

    6. Remove the soft top bow assembly pivot bracket bolts (two per side) from the sport bar using a 10.0 mm wrench or socket driver. 7. Lift the soft top in a upward motion to release the pivot bracket from the sport bar bracket. 8. Remove the soft top from the vehicle and store in a clean, dry locati...

  • Page 204

    9. Reinstall the hard top. Refer to “freedom top three- piece modular hard top — front/rear panel instal- lation” in this section. Installing the soft top — four-door models note: the following procedures are for first time set up only. For future soft top procedures, refer to “soft top” in this sec...

  • Page 205

    Note: if you are doing this alone, use one arm to hold the soft top up, the other to align the brackets. 5. Lower the pivot bracket onto the sport bar bracket mounting tab in a downward motion to lock into tab. 6. Install the pivot bracket bolts back into place using a 10.0 mm wrench or socket drive...

  • Page 206

    Caution! Do not overtighten the screws. You can strip the screws if they are overtightened. 7. Remove the tether strap from the pivot bracket. 8. Using the plastic reinforcement as a handle remove the tether strap from the bracket hook by sliding strap up off hook and slide down the side bow (both s...

  • Page 207

    10. Remove the swing gate bar (black metal bar for bottom of rear window) and set aside. Note: be sure the wire harness in the left rear corner is not tangled in the soft top bows before you lift the top. 11. Unsnap and remove the black boot cover. This cover should be discarded. It was intended as ...

  • Page 208

    Freedom top three-piece modular hard top — if equipped caution! • the hard top is not designed to carry any addi- tional loads such as roof racks, spare tires, build- ing, hunting, or camping supplies, and/or luggage, etc. Also, it was not designed as a structural mem- ber of the vehicle, and thus c...

  • Page 209

    Front panel(s) removal note: left panel must be removed before removing right panel. 1. Fold down the sun visor, and move it to the side. 2. Turn the rear fasteners (knobs) (located on the over- head speaker bar assembly) counterclockwise until they can be removed. 3 understanding the features of yo...

  • Page 210

    3. Turn the center l-shaped locks (two) from the center of the roof panel. 4. Turn the rear l-shaped lock (located above the shoul- der belt anchorage). 208 understanding the features of your vehicle.

  • Page 211

    5. Unlatch the header panel latch located at the top of the windshield. 6. Remove the left-hand panel. To remove the right panel, follow the steps above except for step 3. Freedom top storage bag vehicles equipped with a freedom top modular hard top, come with a freedom top storage bag that allows y...

  • Page 212

    Insert the right side freedom panel into the bag with the latches facing downward. Unfold the black panel divider (ensure the divider is laying flat). Secure the velcro, located at the center of the divider. 210 understanding the features of your vehicle.

  • Page 213

    Insert the left-side freedom panel into the bag with the latches facing upward. Note: ensure the front freedom panel latch is closed prior to inserting the panel into the bag. Unfold the outer flap and zip the freedom bag closed. 3 understanding the features of your vehicle 211.

  • Page 214

    Install the seat attachment strap (at the top of the bag) through the loops. Lift the freedom bag into the vehicle with the hooks and straps facing the back of the rear seat. Attach the clips at the bottom of the bag to the child restraint anchorages, located at the base of the rear seat. 212 unders...

  • Page 215

    Wrap the upper strap around the rear head restraints and loop the strap through the buckle. Pull on the strap to tighten the freedom bag securely against the rear seat. Front panel(s) installation note: set the panels on the windshield frame so that there is no overhang. Also, make sure that the pan...

  • Page 216

    Front panel(s) installation with rear hard top removed 1. Turn the left and right panels over and move the spacer block (located on the rear of the panel) upward 90 degrees. Note: the front panel(s) must be positioned properly to ensure sealing. Set the panels on the windshield frame so that there i...

  • Page 217

    4. Remove the six torx head screws that secure the hard top to the vehicle (along the interior bodyside) using a #40 torx head driver. 5. Open the swing gate all the way to ensure clearance of the rear window glass. Lift the rear window glass. 6. Locate the wire harness on the left rear inside corne...

  • Page 218

    7. Release the red locking tab by pulling outward to the right. 8. To remove the wiring harness push the tab and pull downward to disconnect. Red locking tab push tab to disconnect 216 understanding the features of your vehicle.

  • Page 219

    9. To remove the washer hose, pinch the grips on hose connector and pull downward. 10. Close the swing gate. 11. Remove the hard top from the vehicle. Place the hard top on a soft surface to prevent damage. Note: the removal of the freedom top requires four adults located on each corner. Failure to ...

  • Page 220

    Note: • the torx fasteners that attach the hard top to the body should be torqued to 88 in lb +/- 22 in lb (10 n·m +/- 2.5 n·m). • it is not necessary to pinch connection when rein- stalling washer hose. Push on until click is heard. Door frame caution! Failure to follow these cautions may cause int...

  • Page 221

    Door frame removal 1. Unscrew and remove the door frame attachment knobs (two per door). Warning! Use both hands to remove the door frames. The door frames will fold and could cause injury if both hands are not used. 2. Place one hand on the upper rear and one hand on the front of the door frame. 3....

  • Page 222

    4. Screw the knobs back into the door frame and fold for storage. Store in a secure location. Warning! • do not drive your vehicle on public roads with the door frame(s) removed as you will lose the protec- tion that they can provide. This procedure is fur- nished for use during off-road operation o...

  • Page 223

    Warning! (continued) • do not drive your vehicle on public roads with the doors removed as you will lose the protection that they can provide. This procedure is furnished for use during off-road operation only. Door frame installation — two-door models — if equipped 1. Unfold door frame and unscrew ...

  • Page 224

    4. Starting with the front of the door frame, clip it over the metal side bar and then clip the rear, making sure that the material for the side bar covers is not pinched by the door frame. 5. Starting with the front knob, screw in and tighten both knobs. Repeat on the other side. 222 understanding ...

  • Page 225

    Door frame installation — four-door models — if equipped 1. Install the rear door frame first. 2. Set the door frame pin into the hole on top of the body side, just behind the rear door opening. 3. Position the top of the door frame against the metal sport bar and push onto the side bar making sure ...

  • Page 226

    5. Carefully set the front of the front door frame in the rubber seal at the top of the windshield. 6. Clip the front of the door rail over the side bar making sure that the material for the side bar cover is not pinched by the door frame. 7. Position the rear of the front door frame to lay on top o...

  • Page 227

    9. Tighten the front knob, then the rear most knob, and then the middle knob. Repeat this procedure for the other side. Soft top — two-door models please visit the owners manual on your dvd for instructional videos. Caution! The soft top is not designed to carry any additional loads such as roof rac...

  • Page 228

    If the temperature is below 72°f (24°c) and/or the top has been folded down for a period of time, the top will appear to have shrunk when you raise it, making it difficult to put up. This is caused by a natural contraction of the vinyl coating on the fabric top. Place the vehicle in a warm area. Pul...

  • Page 229

    Caution! (continued) • do not use any tools (screwdrivers, etc.) to pry or force any of the clamps, clips, or retainers securing the soft top. Do not force or pry the soft top framework when opening or closing. Damage to the top may result. Warning! • do not drive the vehicle with the rear window cu...

  • Page 230

    Caution! Failure to follow these cautions may cause interior water damage, stains or mildew on the top material: • it is recommended that the top be free of water prior to opening it. Operating the top, opening a door or lowering a window while the top is wet may allow water to drip into the vehicle...

  • Page 231

    2. Remove the back window. 3. Release header latches from the windshield frame. 3 understanding the features of your vehicle 229.

  • Page 232

    4. Release the sail panel retainers from the body side channel at the rear corners of the vehicle. Note: when releasing the sail panel retainers, it is helpful to pull down on the rear roof bow. 5. Make sure the plastic sleeves are slid rearward over the sunrider link to lock in the link (sunrider m...

  • Page 233

    6. As you begin to lower the top, fold the sail panels so that they rest on top of the soft top. 7. Release the sunrider latch (both sides). 3 understanding the features of your vehicle 231.

  • Page 234

    8. Open the swing gate and lower the top. Note: ensure fabric does not overhang the sides of the vehicle. Quick steps to raising the soft top refer to “raising the soft top” in this section for further information. 1. Open the swing gate and raise the top, engaging the sunrider latches (another pers...

  • Page 235

    2. Engage header latches. 3 understanding the features of your vehicle 233.

  • Page 236

    3. Install rear corner panels. 4. Install the back window. 5. Install the side windows. 234 understanding the features of your vehicle.

  • Page 237

    6. To install the side windows, affix the window tempo- rarily by attaching to the velcro in the rear corner. Start the zipper but close only about 1 in (2.5 cm). 7. Insert the front retainer of the window into the door channel, making sure the retainer is fully seated and properly positioned on the...

  • Page 238

    8. Insert the retainer along the bottom edge of the window into the bottom side channel, beginning at the front and working to the rear of the vehicle. Finish by closing the zipper completely and attaching the velcro along the top and rear of the window. Repeat this step for the opposite side. 1 — i...

  • Page 239

    Lowering the soft top 1 — header bow 6 — quarter window 2 — 2–bow 7 — check strap 3 — 3–bow 8 — front retainer — quarter window 4 — sail panel 9 — bottom retainer — quarter window 5 — body side retainer 3 understanding the features of your vehicle 237.

  • Page 240

    1 — zipper start 2 — zipper finish 3 — swing gate bar 4 — swing gate brackets 5 — sail panels 238 understanding the features of your vehicle.

  • Page 241

    Note: clean side and rear windows before removal to assist in preventing scratching during removal of the soft top. If zippers are difficult to operate due to road dust, etc., clean them with a mild soap solution and a small brush. Cleaning products are available through your authorized dealer. 1. I...

  • Page 242

    4. Open the swing gate. 5. Before unzipping the rear window, release the first 3 in (7.6 cm) of both sail panels from the channel. Remove the swing gate bar by pulling it straight rearward out of the swing gate brackets. • unzip the rear window starting at the right lower corner of the window. Pull ...

  • Page 243

    6. Remove the rear window retainer from the swing gate bracket on both the left and right sides. 7. Stow the windows carefully to avoid scratching. 8. Undo the velcro that runs along the top and rear edge of the side window. 9. Beginning from the rear lower corner, completely unzip the window. 3 und...

  • Page 244

    10. Once unzipped, remove the side window retainers from the door channel and body side channel. Repeat this step on the opposite side. 11. Finish releasing the sail panel retainers from the body side channel at the rear corners of the vehicle. Note: when releasing the sail panel retainers, it is he...

  • Page 245

    13. The swing gate brackets do not need to be removed unless the hard top is being installed. To remove the swing gate brackets, pull the front of the bracket forward while rolling the entire bracket back in toward the vehicle to disengage. 14. Completely release the latches from the loops on the wi...

  • Page 246

    15. Make sure the plastic sleeves are slid rearward over the sunrider link to lock in the link (sunrider models only). 16. Unlatch the side bows from both door rails (sunrider models only). 244 understanding the features of your vehicle.

  • Page 247

    17. Before lowering the top, open the swing gate to prevent possible damage to the rear center high- mounted brake light. Move to the front of the vehicle. Grasp the side bow behind the header and lift the top, folding it toward the rear of the vehicle. Note: help from another person will ease this ...

  • Page 248

    18. Tuck the fabric and the check straps between the bows and as far inward as possible. This will keep any portion of the top from flapping outside of the vehicle. 19. Close the front header latches. 20. Remove the door frames, if desired. Refer to “door frame” in this section for further informati...

  • Page 249

    4. Standing on the side of the vehicle, lift the top by the side bow and the 2–bow (middle bow) up and over the sports bar until the header rests on the top of the windshield frame. 5. Make sure the sunrider bracket on the side bows latches to the door rails (sunrider models only). 3 understanding t...

  • Page 250

    6. Open the header latches and engage the hook on each side onto the windshield loops (do not close the latches). 7. If the swing gate brackets were removed, install them by hooking the rear edge of the bracket on the interior side of the body channel. Then, rotate it rearward and over the channel u...

  • Page 251

    8. Move to the rear of the vehicle and gently pull the sail panels over the rear roof bow. 9. Partially install the sail panel retainers into the body side channel, leaving the last 3 in (7.6 cm) toward the rear window loose (on both sides). Pulling down on the rear roof bow (3–bow) will aid to reac...

  • Page 252

    10. To install the side windows, affix the window tem- porarily by attaching to the velcro in the rear corner. Start the zipper but close only about 1 in (2.5 cm). 11. Insert the front retainer of the window into the door channel, making sure the retainer is fully seated and properly positioned on t...

  • Page 253

    12. Insert the retainer along the bottom edge of the window into the bottom side channel, beginning at the front and working to the rear of the vehicle. Finish by closing the zipper completely and attaching the velcro along the top and rear of the window. Repeat this step for the opposite side. 1 — ...

  • Page 254

    13. Locate the black swing gate bar. Slide the swing gate bar over the receiver at the bottom inside of the rear window. The spongy part of the seal should be down and pointed outward to seal with the swing gate when closed. 252 understanding the features of your vehicle.

  • Page 255

    14. Install the rear window by starting both zipper ends at the lower left corner of the rear window opening. Ensure that the zippers are properly started and aligned before zipping to prevent damage. 15. Run the zipper fully around to the right side of the window. 3 understanding the features of yo...

  • Page 256

    16. Grasp the swing gate bar and position it into the swing gate brackets. 17. Insert the rear window retainer into the swing gate bracket on both the left and right sides. 18. Apply downward pressure on the top corner of the rear soft top bow (3–bow), then complete attaching the sail panel retainer...

  • Page 257

    19. Close the header latches and return the sun visors to their secured position. Sunrider (two-door models) — if equipped caution! Operating the top, opening a door or lowering a window while the top is wet may allow water to drip into the vehicle’s interior. Note: if you are going to be driving fa...

  • Page 258

    Opening the sunrider 1. Unclip and move the sun visors to the side. 2. Release the header latches from the loops on the windshield frame. 3. Make sure to slide the plastic sleeves forward to unlock the sunrider links. 4. Grasp the header and lift the top back. Make sure the material is folded back a...

  • Page 259

    5. Locate the straps to secure the side bows. Wrap the straps around the bows as shown. Repeat on the other side. 6. Reposition the sun visors. 3 understanding the features of your vehicle 257.

  • Page 260

    Closing the sunrider 1. Remove the straps from the side bows. 2. Unclip and move the sun visors to the side. 3. Grasp the front header and pull it to the front of the vehicle. 4. Hook the header latches to the loops on the wind- shield frame, close latches, and return the sun visors to their origina...

  • Page 261

    Caution! • do not run a fabric top through an automatic car wash. Window scratches and wax buildup may result. • do not lower the top when the temperature is below 41°f (5°c). Damage to the top may result. • do not lower the top when the windows are dirty. Grit may scratch the window. • do not move ...

  • Page 262

    Warning! (continued) rely on them to contain occupants within the ve- hicle or to protect against injury during an acci- dent. Remember, always wear seat belts. • make sure hands and fingers are clear of all pinch points when installing and removing the soft tops. The zippers and side bows may cause...

  • Page 263

    Note: do not remove any of the three attachment knobs unless you are planning on installing the hard top. Quick steps for lowering the soft top 1. Remove the side windows. 3 understanding the features of your vehicle 261.

  • Page 264

    2. Remove the back window. Note: start zipper from the right side to remove back window. 3. Release header latches from the windshield frame. 262 understanding the features of your vehicle.

  • Page 265

    4. Release the sail panel retainers from the body side channel at the rear corners of the vehicle. Note: when releasing the sail panel retainers, it is helpful to pull down on the rear roof bow. 5. Fold the sail panels so that they rest on top of the soft top. 3 understanding the features of your ve...

  • Page 266

    6. Fold header rearward, pulling the fabric to the rear. 7. Release sunrider latch (both sides). 264 understanding the features of your vehicle.

  • Page 267

    8. Open the swing gate and lower the top. Note: ensure the fabric does not overhang the sides of the vehicle. 3 understanding the features of your vehicle 265.

  • Page 268

    Quick steps for raising the soft top 1. Open the swing gate and raise the top, engaging the sunrider latches (another person may be needed to help with this operation). 266 understanding the features of your vehicle.

  • Page 269

    2. Install rear corner panels. 3. Rotate the header forward. 3 understanding the features of your vehicle 267.

  • Page 270

    4. Engage the header latches. 5. Install the back window. 268 understanding the features of your vehicle.

  • Page 271

    6. Install the side windows. 7. To install the side windows, affix the window tempo- rarily by attaching to the velcro in the rear corner. Start the zipper but close only about 1 in (2.5 cm). 3 understanding the features of your vehicle 269.

  • Page 272

    8. Insert the front retainer of the window into the door channel, making sure the retainer is fully seated and properly positioned on the door frame. Failure to do so can result in wind and water leaks or damage to the window. 1 — incorrect insertion 2 — correct insertion 270 understanding the featu...

  • Page 273

    9. Insert the retainer along the bottom edge of the window into the bottom side channel, beginning at the front and working to the rear of the vehicle. Finish by closing the zipper completely and attaching the velcro along the top and rear of the window. Repeat this step for the opposite side. 3 und...

  • Page 274

    Folding down the soft top 1 — header bow 6 — body side retainer 2 — 2–bow 7 — quarter window 3 — 3–bow 8 — check strap 4 — 4–bow 9 — front retainer — quarter window 5 — sail panel 10 — bottom retainer — quarter window 272 understanding the features of your vehicle.

  • Page 275

    1 — zipper start 2 — zipper finish 3 — swing gate bar 4 — swing gate brackets 5 — sail panels 3 understanding the features of your vehicle 273.

  • Page 276

    Note: clean side and rear windows before removal to assist in preventing scratching during removal of the soft top. If zippers are difficult to operate due to road dust, etc., clean them with a mild soap solution and a small brush. Cleaning products are available through your authorized dealer. 1. I...

  • Page 277

    4. Open the swing gate. 5. Before unzipping the rear window, release the first 3 in (7.6 cm) of both sail panels from the channel. Remove the swing gate bar by pulling it straight rearward out of the swing gate brackets. • unzip the rear window starting at the right lower corner of the window. Pull ...

  • Page 278

    6. Remove the rear window retainer from the swing gate bracket on both the left and right sides. 7. Stow the windows carefully to avoid scratching. 8. Undo the velcro that runs along the top and rear edge of the side window. 9. Beginning from the rear lower corner, completely unzip the window. 10. O...

  • Page 279

    11. Finish releasing the sail panel retainers from the body side channel at the rear corners of the vehicle. Note: when releasing the sail panel retainers, it is helpful to pull down on the rear roof bow. 12. Fold the sail panels so that they rest on top of the soft top. 3 understanding the features...

  • Page 280

    13. The swing gate brackets do not need to be removed unless the hard top is being installed. To remove the swing gate brackets, pull the front of the bracket forward while rolling the entire bracket back in toward the vehicle to disengage. 14. Grasp the front side bow behind the header, and lift th...

  • Page 281

    15. Fold back the front section of the top, pulling the fabric rearward. Gently rest the header on top of the rear portion of the deck. 16. Fold the top so that the material forms a ⬙ w ⬙ as shown. Enter the vehicle and move the material into two folds. 3 understanding the features of your vehicle 2...

  • Page 282

    17. Release the side bows by pushing down on the latch above the front of the rear door. Push the top rearward to disengage. Repeat this step on the other side. 18. Before lowering the top, open the swing gate to prevent possible damage to the rear center high- mounted brake light. Grasp the folded ...

  • Page 283

    20. Tuck the fabric and the check straps between the bows as far inside as possible. This will keep any portion of the top from flapping outside of the vehicle. 21. Once the top is fully down, use the velcro straps provided to secure the top to the vehicle by wrapping the strap around the side bows ...

  • Page 284

    Putting up the soft top note: be extremely careful when putting up the soft top to prevent the doors from getting scratched. It may be helpful to open the rear doors. 1. Install the door frames, if removed. Refer to “door frame” in this section for further information. 2. Undo the straps used to sec...

  • Page 285

    6. Ensure that the top locks into the sunrider locking mechanisms that are located above the front of the rear doors. 7. Unclip and move the sun visors to the side. 3 understanding the features of your vehicle 283.

  • Page 286

    8. Standing on the side of the vehicle, lift the top by the side bow until it rests on the windshield frame. 9. Open the header latches and engage the hook on each side onto the windshield loops (do not close the latches). 284 understanding the features of your vehicle.

  • Page 287

    10. If the swing gate brackets were removed, install them by hooking the rear edge of the bracket on the interior side of the body channel. Then, rotate it rearward and over the channel until it snaps onto the exterior part of the rail. To be properly located, the bracket must only be clipped to the...

  • Page 288

    Partially install the sail panel retainers into the body side channel, leaving the last 3 in (7.6 cm) toward the rear window loose (on both sides). Pulling down on the rear roof bow (4–bow) will aid in reaching the channel with the retainers. 12. To install the side windows, affix the window tem- po...

  • Page 289

    13. Insert the front retainer of the window into the door channel, making sure the retainer is fully seated and properly positioned on the door frame. Failure to do so can result in wind and water leaks or damage to the window. 14. Insert the retainer along the bottom edge of the window into the bot...

  • Page 290

    The velcro along the top and rear of the window. Repeat this step for the opposite side. 288 understanding the features of your vehicle.

  • Page 291

    15. Locate the black swing gate bar. Slide the swing gate bar over the receiver at the bottom inside of the rear window. The spongy part of the seal should be down and pointed outward to seal with the swing gate when closed. 16. Install the rear window by starting both zipper ends at the lower left ...

  • Page 292

    18. Grasp the swing gate bar and position it into the swing gate brackets. 19. Insert the rear window retainer into the swing gate bracket on both the left and right sides. 290 understanding the features of your vehicle.

  • Page 293

    20. Complete the installation of the sail panel by insert- ing the rest of the retainer into the body channel. 21. Close the header latches and return the sun visors to their secured position. Sunrider (four-door models) — if equipped caution! Operating the top, opening a door or lowering a window w...

  • Page 294

    Opening the sunrider 1. Unclip and move the sun visors to the side. 2. Release the header latches from the loops on the windshield frame. 3. Make sure to slide the plastic sleeves forward to unlock the sunrider links. 292 understanding the features of your vehicle.

  • Page 295

    4. Grasp the front side bow behind the header, and lift the top. 5. Fold back the front section of the top and gently rest the header on top of the rear portion of the deck. 3 understanding the features of your vehicle 293.

  • Page 296

    6. Fold the top so that the material forms a ⬙ w ⬙ as shown. Enter the vehicle and move the material into two folds. 7. Secure the top by using the two provided straps. Each strap will wrap around the side bow and velcro to itself; use one strap on each side of the vehicle. 294 understanding the fea...

  • Page 297

    Closing the sunrider perform the above steps in the opposite order. Note: failure to fold the fabric rearward will allow the material to sag and may block the rearview mirror. Folding windshield the fold-down windshield and removable side bars on your vehicle are structural elements that can provide...

  • Page 298

    Warning! Carefully follow these warnings to help protect against personal injury: • do not drive your vehicle on-road with the wind- shield down. • do not drive your vehicle unless the windshield is securely fastened, either up or down. • eye protection, such as goggles, should be worn at all times ...

  • Page 299

    3. Remove the sun visor. 4. Remove the a-pillar cap. 5. Disconnect microphone (if equipped with uconnect phone). 6. Open the sport bar velcro covering. 7. Remove the one hex bolt (13 mm) visible through the plastic trim on the bottom side of the side bar, one hex bolt (13 mm) on the side of the side...

  • Page 300

    Caution! Do not remove the head impact foam from the side bars, as damage to the foam may result. Note: store all of the mounting bolts in their original threaded holes and tighten for safekeeping. 8. Remove the side bar assembly, and reattach the sport bar velcro covering. 9. To safely store the si...

  • Page 301

    Note: it may be necessary to use a battery terminal puller tool in order to separate the wiper arms from the shaft after the nuts have been removed. 11. Remove the lower windshield plates by removing the six black round-headed torx head screws (using a #40 torx head driver) on each side of the base ...

  • Page 302

    Raising the windshield and replacing side bars 1. Raise the windshield. 2. Loosely attach the rear of the side bar to the sport bar. Refer to step 4 of “lowering windshield and remov- ing side bars” earlier in this section. • reattach the sport bar velcro covering. 3. Attach the front of the side ba...

  • Page 303

    5. Install the lower windshield plates with the six black round-headed torx head screws (using a #40 torx head driver) on each side of the base of the wind- shield. 6. Reinstall the wiper arms. Rear window features — hard top only rear window wiper/washer — if equipped a rotary switch on the center ...

  • Page 304

    Rotate the switch upward to the first detent position for rear wiper operation. Rotate the switch upward past the first detent to activate the rear washer. The washer pump and the wiper will continue to operate as long as the switch is held. Upon release, the wiper will cycle two to three times befo...

  • Page 305

    Caution! Failure to follow these cautions can cause damage to the heating elements: • use care when washing the inside of the rear window. Do not use abrasive window cleaners on the interior surface of the window. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements....

  • Page 307: Contents

    Understanding your instrument panel contents 䡵 instrument panel features . . . . . . . . . .309 䡵 instrument cluster . . . . . . . . . . . . . . . . .310 䡵 warning and indicator lights . . . . . . .314 ▫ red telltale indicator lights . . . . . . . . . . . . . .315 ▫ yellow telltale indicator lights ...

  • Page 308

    ▫ average fuel economy. . . . . . . . . . . . . . . . . .351 ▫ distance to empty (dte) . . . . . . . . . . . . . . . .351 ▫ elapsed time . . . . . . . . . . . . . . . . . . . . . . . .352 ▫ vehicle information . . . . . . . . . . . . . . . . . . . .352 ▫ evic units selection (units in display) . . ....

  • Page 309

    ▫ operation instructions — disc mode for cd and mp3/wma audio play, dvd – video . . .392 ▫ notes on playing mp3/wma files. . . . . . . . .394 ▫ list button — disc mode for mp3/wma play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .397 ▫ info button — disc mode for mp3/wma play . . . ....

  • Page 310

    䡵 climate controls . . . . . . . . . . . . . . . . . . .415 ▫ manual heating and air conditioning . . . . . .415 ▫ automatic temperature control (atc) — if equipped . . . . . . . . . . . . . . . . . . . . . . . . . . .419 ▫ operating tips . . . . . . . . . . . . . . . . . . . . . . .425 308 understa...

  • Page 311

    Instrument panel features 1 — air outlet 7 — climate controls 2 — instrument cluster 8 — power outlet 3 — radio 9 — lower switch bank 4 — assist handle 10 — power mirror switch — if equipped 5 — glove compartment 11 — horn 6 — power window switches 4 understanding your instrument panel 309.

  • Page 312

    Instrument cluster 310 understanding your instrument panel.

  • Page 313

    1. Fuel gauge • the pointer shows the level of fuel in the fuel tank when the ignition switch is in the on/run position. • the fuel pump symbol points to the side of the vehicle where the fuel filler door is located. 2. Speedometer • indicates vehicle speed. 3. Tachometer • indicates the engine spee...

  • Page 314

    Caution! (continued) remains on the “h”, turn the engine off immediately and call an authorized dealer for service. Warning! A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant. You may want to call an authorized dealer for service if your vehicl...

  • Page 315

    Vehicle odometer messages if the vehicle is equipped with the optional electronic vehicle information center (evic) in the instrument cluster, all messages will display in the evic. Refer to “electronic vehicle information center — if equipped” in this section for further information. When the appro...

  • Page 316

    7. Electronic vehicle information center (evic) dis- play / compass mini-trip computer display — if equipped • when the appropriate conditions exist, this display shows the electronic vehicle information center (evic) messages. Refer to “electronic vehicle infor- mation center” in “understanding you...

  • Page 317

    Red telltale indicator lights charging system warning light red telltale light what it means charging system warning light this light shows the status of the electrical charging system. If the light stays on or comes on while driving, turn off some of the vehicle’s nonessential electrical devices or...

  • Page 318

    Seat belt reminder warning light red telltale light what it means seat belt reminder warning light when the ignition switch is first turned to on/run, this light will turn on for four to eight seconds as a bulb check. During the bulb check, if the driver’s seat belt is unbuckled, a chime will sound....

  • Page 319

    Oil pressure warning light red telltale light what it means oil pressure warning light this light indicates low engine oil pressure. If the light turns on while driving, stop the ve- hicle and shut off the engine as soon as possible. A chime will sound when this light turns on. Do not operate the ve...

  • Page 320

    Brake warning light red telltale light what it means united states canada brake warning light this light monitors various brake functions, including brake fluid level and parking brake ap- plication. If the brake light turns on it may indicate that the parking brake is applied, that the brake fluid ...

  • Page 321

    The dual brake system provides a reserve braking capac- ity in the event of a failure to a portion of the hydraulic system. A leak in either half of the dual brake system is indicated by the brake warning light, which will turn on when the brake fluid level in the master cylinder has dropped below a...

  • Page 322

    Air bag warning light red telltale light what it means air bag warning light this light will turn on for four to eight seconds as a bulb check when the ignition switch is first turned to on/run. If the light is either not on during startup, stays on, or turns on while driving, have the system inspec...

  • Page 323

    Coolant temperature warning light red telltale light what it means coolant temperature warning light this light warns of an overheated engine condition. If the light turns on while driving, safely pull over and stop the vehicle. If the a/c system is on, turn it off. Also, shift the transmission into...

  • Page 324

    Vehicle security warning light — if equipped red telltale light what it means vehicle security warning light — if equipped this light will flash at a fast rate for approximately 15 seconds when the vehicle security alarm is arming, and then will flash slowly until the vehicle is disarmed. 322 unders...

  • Page 325

    Electronic throttle control (etc) warning light red telltale light what it means electronic throttle control (etc) warning light this light informs you of a problem with the electronic throttle control (etc) system. If a problem is detected while the engine is running, the light will either stay on ...

  • Page 326

    Yellow telltale indicator lights low fuel warning indicator light yellow telltale light what it means low fuel warning indicator light when the fuel level reaches approximately 2.8 gal (10.6 l), this light will turn on and a single chime will sound. 324 understanding your instrument panel.

  • Page 327

    Anti-lock brake (abs) indicator light yellow telltale light what it means anti-lock brake (abs) indicator light this light monitors the anti-lock brake system (abs). The light will turn on when the igni- tion switch is placed in the on/run position and may stay on for as long as four seconds. If the...

  • Page 328

    Engine check/malfunction indicator light (mil) yellow telltale light what it means engine check/malfunction indicator light (mil) the engine check/malfunction indicator light (mil) is a part of an onboard diagnostic system called obd ii that monitors engine and automatic transmission control systems...

  • Page 329

    Caution! Prolonged driving with the malfunction indicator light (mil) on could cause damage to the engine control system. It also could affect fuel economy and driveability. If the mil is flashing, severe catalytic converter damage and power loss will soon occur. Immediate service is required. Warni...

  • Page 330

    Tire pressure monitoring indicator light yellow telltale light what it means tire pressure monitoring indicator light the warning light switches on and a message is displayed to indicate that the tire pressure is lower than the recommended value and/or that slow pressure loss is occurring. In these ...

  • Page 331

    Important: do not continue driving with one or more flat tires as handling may be compromised. Stop the vehicle, avoiding sharp braking and steering. Repair immediately using the dedicated tire repair kit and contact your authorized dealership as soon as possible. Each tire, including the spare (if ...

  • Page 332

    Illuminated. This sequence will continue upon subse- quent vehicle start-ups as long as the malfunction exists. When the malfunction indicator is illuminated, the sys- tem may not be able to detect or signal low tire pressure as intended. Tpms malfunctions may occur for a variety of reasons, includi...

  • Page 333

    Electronic stability control (esc) indicator light — if equipped yellow telltale light what it means electronic stability control (esc) indicator light — if equipped the “esc indicator light” in the instrument cluster will come on when the ignition switch is turned to the on/run position. It should ...

  • Page 334

    Electronic stability control (esc) off indicator light — if equipped yellow telltale light what it means electronic stability control (esc) off indicator light — if equipped this light indicates the electronic stability control (esc) is off. Front axle lock indicator light — if equipped yellow tellt...

  • Page 335

    Rear axle lock indicator light — if equipped yellow telltale light what it means rear axle lock indicator light this light indicates when the rear axle lock has been activated. 4wd indicator light — if equipped yellow telltale light what it means 4wd indicator light this light alerts the driver that...

  • Page 336

    Sway bar indicator light — if equipped yellow telltale light what it means sway bar indicator light this indicator will illuminate when the front sway bar is disconnected. Green telltale indicator lights front fog indicator light — if equipped green telltale light what it means front fog indicator l...

  • Page 337

    Turn signal indicator lights green telltale light what it means turn signal indicator lights the left or right arrow will flash with the corresponding exterior turn signal lights when the turn signal lever is operated. A chime will sound if the vehicle is driven more than 1 mile (1.6 km) with either...

  • Page 338

    Hill decent control (hdc) indicator light — if equipped white telltale light what it means hill decent control (hdc) indicator light this indicator shows when the hill descent control (hdc) feature is turned on. The lamp will be on solid when hdc is armed. Hdc can only be armed when the transfer cas...

  • Page 339

    Blue telltale indicator lights high beam indicator light blue telltale light what it means high beam indicator light this indicator shows that the high beam headlights are on. Push the multifunction control lever away from you to switch the headlights to high beam. Pull the lever toward you to switc...

  • Page 340

    Compass and trip computer — if equipped the compass/trip computer features a driver- interactive display (displays information on outside tem- perature, compass direction, and trip information). It is located on the lower left part of the cluster below the speedometer. Control buttons the compass/te...

  • Page 341

    Push and release the step button on the steering wheel to access the options in the compass display. Note: the system will display the last known outside temperature when starting the vehicle and may need to be driven several minutes before the updated tempera- ture is displayed. Engine temperature ...

  • Page 342

    Compass/temperature display note: if the vehicle is equipped with a uconnect navi- gation radio, the nav system will provide the compass direction, and the variance and calibration menus will be unavailable. The compass will perform accurately, based on gps signals instead of the earth’s magnetic fi...

  • Page 343

    Button to increase the variance one step. Repeat as necessary until the desired variance is achieved. Note: the factory default zone is 8. During program- ming, the zone value will wrap around from zone 15 to zone 1. Manual compass calibration if the compass appears erratic, inaccurate or abnormal, ...

  • Page 344

    Average fuel economy / distance to empty (dte) / elapsed time • average fuel economy shows the average fuel economy since the last reset. When the fuel economy is reset, the digits will go blank while the history information is erased. The averaging will restart when enough new distance and fuel dat...

  • Page 345

    Trip a shows the total distance traveled for trip a since the last reset. Trip b shows the total distance traveled for trip b since the last reset. Eco (fuel saver indicator) — if equipped the eco indicator will illuminate when you are driving in a fuel efficient manner and can be used to modify dri...

  • Page 346

    Electronic vehicle information center (evic) — if equipped the electronic vehicle information center (evic) fea- tures a driver-interactive display that is located in the instrument cluster. This system conveniently allows the driver to select a variety of useful information by pushing the switches ...

  • Page 347

    • system status and warnings (door ajar, etc.) • personal settings (customer-programmable features) the system allows the driver to select information by pushing the following buttons mounted on the steering wheel: • menu button push and release the menu button to advance the display to each of the ...

  • Page 348

    • right arrow button push and release the right arrow button when prompted by the evic to reset main menu features with a reset capability or to change personal settings. • down arrow button push and release the down arrow button when prompted by the evic to step through vehicle info submenu or stor...

  • Page 349

    • personal settings not avail. – vehicle in motion — manual transmission • door open (with vehicle graphic showing which door is open. A single chime sounds if the vehicle is in motion). • gate open (with vehicle graphic showing the liftgate/back door open and a single chime sounds if the vehicle is...

  • Page 350

    • transmission temp — automatic transmission only • oil life remaining (automatic oil change indica- tor) • evic units selection • system status and warnings • personal settings note: for features in the evic that can be reset (average fuel economy and elapsed time), the evic prompts a reset with th...

  • Page 351

    Eco (fuel saver mode) — if equipped the eco message will display below the outside tem- perature in the evic display (if the audio system is on the eco indicator will override the audio information display line if the ⬙ display fuel saver ⬙ personal setting is on — see ⬙ personal settings ⬙ section)...

  • Page 352

    3. Push the down button until “calibrate compass” displays in the evic. 4. Push and release the right button to start the calibration. The “cal” indicator will display in the evic. 5. Complete one or more 360–degree turns (in an area free from large metal or metallic objects) until the “cal” indicat...

  • Page 353

    To change the compass variance: 1. Turn the ignition switch run (it is not necessary to start the engine). 2. Push the menu button until personal settings (customer-programmable features) displays in the evic. 3. Push the down button until “compass variance” message and the last variance zone number...

  • Page 354

    When the dte value is less than 30 miles (48 km) estimated driving distance, the dte display will change to a text display of ⬙ low fuel.” this display will continue until the vehicle runs out of fuel. Adding a significant amount of fuel to the vehicle will turn off the low fuel text, and a new dte ...

  • Page 355

    Oil change required your vehicle is equipped with an engine oil change indicator system. The “oil change required” message will display in the evic display for approximately 5 seconds after a single chime has sounded to indicate the next scheduled oil change interval. The engine oil change indicator...

  • Page 356

    System warnings displays “system ok” if there are no active warning messages stored. Pushing and releasing the down arrow button when “system ok” is displayed will do nothing. Displays “system warnings present” if there are active warning messages stored. Pushing and releasing the down arrow button ...

  • Page 357

    Auto unlock on exit when on is selected, all doors will unlock when the vehicle is stopped and the transmission is in the park or neutral position, and the driver’s door is opened. To make your selection, push and release the right button until “on” or “off” appears. Rke unlock — if equipped when “d...

  • Page 358

    Headlamps with wipers (available with auto headlights only) when on is selected, and the headlight switch is in the auto position, the headlights will turn on approxi- mately 10 seconds after the wipers are turned on. If the headlights were turned on by this feature, they will also turn off when the...

  • Page 359

    Display units in the evic can be changed between english and metric units of measure. The units apply to the outside tem- perature, average fuel economy, and distance to empty. To make your selection, push and release the right button until “u.S.” or ⬙ metric ⬙ appears. Nav–turn by turn — if equippe...

  • Page 360

    Uconnect 130 operating instructions — radio mode note: the ignition switch must be in the on/run or acc position to operate the radio. Power switch/volume control (rotary) push the on/volume control knob to turn on the radio. Push the on/volume control knob a second time to turn off the radio. Elect...

  • Page 361

    Another selection. Holding either button will bypass stations without stopping, until you release it. Time button push the time button to alternate display of the time and radio frequency. Clock setting procedure 1. Push and hold the time button until the hours blink. 2. Adjust the hours by turning ...

  • Page 362

    Push the rotary tune/scroll control knob a second time and mid will display. Turn the tune/scroll control knob to the right or left to increase or decrease the mid-range tones. Push the rotary tune/scroll control knob a third time and treble will display. Turn the tune/scroll control knob to the rig...

  • Page 363

    Display window. Each button can be set for set 1 and set 2 in both am and fm. This allows a total of 12 am and 12 fm stations to be stored into pushbutton memory. The stations stored in set 2 memory can be selected by pushing the pushbutton twice. Every time a preset button is used, a corresponding ...

  • Page 364

    If you insert a disc with the ignition on/run and the radio on, the unit will switch from radio to cd mode and begin to play when you insert the disc. The display will show the track number, and index time in minutes and seconds. Play will begin at the start of track 1. Caution! • this cd player wil...

  • Page 365

    The current selection. Pushing and holding the seek button will allow faster scrolling through the tracks in cd and mp3 modes. Time button push this button to change the display from a large cd playing time display to a small cd playing time display. Rw/ff push and hold the ff (fast forward) button ...

  • Page 366

    Supported medium formats (file systems) the medium formats supported by the radio are iso 9660 level 1 and level 2 and includes the joliet extension. When reading discs recorded using formats other than iso 9660 level 1 and level 2, the radio may fail to read files properly and may be unable to play...

  • Page 367

    When using the mp3 encoder to compress audio data to an mp3 file, the bit rate and sampling frequencies in the following table are supported. In addition, variable bit rates (vbr) are also supported. The majority of mp3 files use a 44.1 khz sampling rate and a 192, 160, 128, 96 or vbr bit rate. Mpeg...

  • Page 368

    Loading times for playback of mp3 files may be affected by the following: • media - cd-rw media may take longer to load than cd-r media • medium formats - multisession discs may take longer to load than non-multisession discs • number of files and folders - loading times will increase with more file...

  • Page 369

    Uconnect 130 with satellite radio operating instructions — radio mode note: the ignition switch must be in the on or acc position to operate the radio. Power switch/volume control (rotary) push the on/volume control knob to turn on the radio. Push the on/volume control knob a second time to turn off...

  • Page 370

    Another selection. Holding either button will bypass stations without stopping, until you release it. Voice command system (radio) — if equipped refer to “voice command” in “understanding the fea- tures of your vehicle”. Voice command button uconnect phone — if equipped push this button to operate t...

  • Page 371

    3. After adjusting the hours, push the right side tune/ scroll control knob to set the minutes. The minutes will begin to blink. 4. Adjust the minutes using the right side tune/ scroll control knob. Push the tune/scroll con- trol knob to save time change. 5. To exit, push any button/knob or wait fiv...

  • Page 372

    Setting the tone, balance and fade push the rotary tune/scroll control knob and bass will display. Turn the tune/scroll control knob to the right or left to increase or decrease the bass tones. Push the rotary tune/scroll control knob a second time and mid will display. Turn the tune/scroll control ...

  • Page 373

    Toggle the music type button to select the following format types: program type 16-digit character display no program type or undefined none adult hits adlt hit classical classicl classic rock cls rock college college country country foreign language language information inform jazz jazz news news n...

  • Page 374

    By pushing the seek button when the music type icon is displayed, the radio will be tuned to the next frequency station with the same selected music type name. The music type function only operates when in the fm mode. If a preset button is activated while in the music type (program type) mode, the ...

  • Page 375

    And 12 fm stations to be stored into pushbutton memory. The stations stored in set 2 memory can be selected by pushing the pushbutton twice. Every time a preset button is used, a corresponding button number will display. Buttons 1 - 6 these buttons tune the radio to the stations that you commit to p...

  • Page 376

    If you insert a disc with the ignition on and the radio on, the unit will switch from radio to cd mode and begin to play when you insert the disc. The display will show the track number, and index time in minutes and seconds. Play will begin at the start of track 1. Caution! • this cd player will ac...

  • Page 377

    Seek button push the right seek button for the next selection on the cd. Push the left seek button to return to the beginning of the current selection, or return to the beginning of the previous selection if the cd is within the first second of the current selection. Pushing and holding the seek but...

  • Page 378

    Supported media (disc types) the mp3 file recording media supported by the radio are cdda, cd-r, cd-rw, mp3, and cdda+mp3. Supported medium formats (file systems) the medium formats supported by the radio are iso 9660 level 1 and level 2 and includes the joliet extension. When reading discs recorded...

  • Page 379

    Supported mp3 file formats the radio will recognize only files with the *.Mp3 exten- sion as mp3 files. Non-mp3 files named with the *.Mp3 extension may cause playback problems. The radio is designed to recognize the file as an invalid mp3 and will not play the file. When using the mp3 encoder to co...

  • Page 380

    Playback of mp3 files when a medium containing mp3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the mp3 files. Loading times for playback of mp3 files may be affected by the following: • med...

  • Page 381

    Push and hold the info button again for three seconds to return to ⬙ elapsed time ⬙ display. Operation instructions — auxiliary mode the auxiliary (aux) jack is an audio input jack which allows the user to plug in a portable device such as an mp3 player and utilize the vehicle’s audio system to ampl...

  • Page 382

    Information, call the toll-free number 888-539-7474, or visit the sirius web site at www.Siriusxm.Com, or at www.Siriusxm.Ca for canadian residents. Electronic serial number/sirius identification number (esn/sid) please have the following information available when calling: 1. The electronic serial ...

  • Page 383

    Reception quality satellite reception may be interrupted due to one of the following reasons: • the vehicle is parked in an underground parking structure or under a physical obstacle. • dense tree coverage may interrupt reception in the form of short audio mutes. • driving under wide bridges or alon...

  • Page 384

    Additional three seconds will make the radio display the song title all of the time (push and hold again to return to normal display). Rw/ff pushing the rw (rewind) or ff (fast forward) buttons causes the tuner to search for the next channel in the direction of the arrows. Tune control (rotary) turn...

  • Page 385

    Set button — to set the pushbutton memory when you are receiving a channel that you wish to commit to pushbutton memory, push the set button. The symbol set 1 will now show in the display window. Select the button (1-6) you wish to lock onto this channel and push and release that button. If a button...

  • Page 386

    Uconnect 230 – am/fm stereo radio and 6–disc cd/dvd changer (mp3/wma aux jack) operating instructions — radio mode note: the ignition switch must be in the on or acc position to operate the radio. Power switch/volume control (rotary) push the on/volume control knob to turn on the radio. Push the on/...

  • Page 387

    Another selection. Holding either button will bypass stations without stopping, until you release it. Scan button pushing the scan button causes the tuner to search for the next listenable station in am, fm or satellite (if equipped) frequencies, pausing for five seconds at each listenable station b...

  • Page 388

    3. After adjusting the hours, push the right side tune/ scroll control knob to set the minutes. The minutes will begin to blink. 4. Adjust the minutes using the right side tune/ scroll control knob. Push the tune/scroll con- trol knob to save the time change. 5. To exit, push any button/knob or wait...

  • Page 389

    Push the rotary tune/scroll control knob a third time and treble will display. Turn the tune/scroll control knob to the right or left to increase or decrease the treble tones. Push the rotary tune/scroll control knob a fourth time and balance will display. Turn the tune/ scroll control knob to the r...

  • Page 390

    Program type 16-digit character display information inform jazz jazz news news nostalgia nostalga oldies oldies personality persnlty public public rhythm and blues r & b religious music rel musc religious talk rel talk rock rock soft soft soft rock soft rck soft rhythm and blues soft r & b program t...

  • Page 391

    Setup button pushing the setup button allows you to select between the following items: note: turn the tune/scroll control knob to scroll through the entries. Push the audio/select button to select an entry and make changes. • dvd enter — when the disc is in dvd menu mode, selecting dvd enter will a...

  • Page 392

    • power — allows you to turn the power on and off (if equipped). • lock — locks out rear remote controls (if equipped). • ch1/ch2 — allows the user to change the mode of either the ir1 or ir2 wireless headphones by pushing the audio/select button (if equipped). • set home clock — pushing the select ...

  • Page 393

    Subtitle language — if equipped selecting this item allows you to choose a default subtitle language (effective only if the language is supported by the disc). You can select a language not listed by scrolling down and selecting ⬙ other. ⬙ enter the country code using the tune/scroll control knob to...

  • Page 394

    Set button — to set the pushbutton memory when you are receiving a station that you wish to commit to pushbutton memory, push the set button. The symbol set 1 will now show in the display window. Select the button (1-6) you wish to lock onto this station and push and release that button. If a button...

  • Page 395

    To an authorized dealer to change the region code of the player a maximum of five times. Caution! The radio may shut down during extremely hot conditions. When this occurs, the radio will indicate “disc hot” and shut off until a safe temperature is reached. This shutdown is necessary to protect the ...

  • Page 396

    Display will show ⬙ ejecting disc ⬙ when the disc is being ejected and prompt the user to remove the disc. Push and hold the eject button for five seconds and all cds will be ejected from the radio. The disc can be ejected with the radio and ignition off. Seek button (cd mode) push the right seek bu...

  • Page 397

    Supported media (disc types) the mp3/wma file recording media supported by the radio are cdda, cd-r, cd-rw, mp3,wma, dvd video, dvd-r, dvd-rw, dvd+r, dvd+rw, and cdda+mp3. Supported medium formats (file systems) the medium formats supported by the radio are iso 9660 level 1 and level 2 and includes ...

  • Page 398

    Supported mp3/wma file formats the radio will recognize only files with the *.Mp3/wma extension as mp3/wma files. Non-mp3/wma files named with the *.Mp3/wma extension may cause play- back problems. The radio is designed to recognize the file as an invalid mp3/wma and will not play the file. When usi...

  • Page 399

    Playlist files are not supported. Mp3 pro files are not supported. Playback of mp3/wma files when a medium containing mp3/wma data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the mp3/wma files. ...

  • Page 400

    Push the info button once more to return to ⬙ elapsed time ⬙ priority mode. Push and hold the info button for three seconds or more and radio will display song titles for each file. Push and hold the info button again for three seconds to return to ⬙ elapsed time ⬙ display. Operation instructions — ...

  • Page 401

    Rw/ff (auxiliary mode) no function. Set button (auxiliary mode) no function. Operating instructions (voice command system) — if equipped refer to “voice command” for further details. Operating instructions (uconnect phone) — if equipped refer to “uconnect phone” for further details. Dolby manufactur...

  • Page 402

    Sports, news, entertainment, and programming for chil- dren, directly from its satellites and broadcasting studios. Note: sirius service is not available in hawaii and has limited coverage in alaska. System activation sirius satellite radio service is pre-activated, and you may begin listening immed...

  • Page 403

    Selecting uconnect (satellite) mode push the sat button until ⬙ sat ⬙ appears in the display. A cd may remain in the radio while in the satellite radio mode. Satellite antenna to ensure optimum reception, do not place items on the roof around the rooftop antenna location. Metal objects placed within...

  • Page 404

    Scan button pushing the scan button causes the tuner to search for the next channel, pausing for eight seconds before con- tinuing to the next. To stop the search, push the scan button a second time. Info button pushing the info button will cycle the display informa- tion between artist, song title,...

  • Page 405

    Setup button pushing the setup button allows you to select the following items: • display sirius id number — push the audio/ select button to display the sirius id number. This number is used to activate, deactivate, or change the sirius subscription. Set button — to set the pushbutton memory when y...

  • Page 406

    Uconnect 430/430n cd/dvd/hdd/nav — if equipped refer to your uconnect supplement manual for detailed operating instructions. Operating instructions (voice command system) — if equipped refer to “voice command” for further details. Operating instructions (uconnect phone) — if equipped refer to “uconn...

  • Page 407

    Connecting an external usb device use a connection cable to connect an external usb device to the vehicles usb/aux connector port which is located in the center console. Once the audio device is connected and synchronized to the vehicles usb/mp3 control system (external usb device may take a few min...

  • Page 408

    • the audio device battery charges when plugged into the usb/aux connector (if supported by the specific audio device). Controlling the ipod or external usb device using radio buttons to enter the ipod/usb/mp3 control mode and access a connected audio device, either push the “aux” button on the radi...

  • Page 409

    • use the seek and seek >> buttons to jump to the previous or next track. Pushing the seek >> button during play mode will jump to the next track in the list, or push the vr button and say ⬙ next or previous track. ⬙ • while a track is playing, push the info button to see the associated metadata (ar...

  • Page 410

    Tune control knob: the tune control knob functions in a similar manner as the scroll wheel on the audio device or external usb device. • turning it clockwise (forward) and counterclockwise (backward) scrolls through the lists, displaying the track detail on the radio display. Once the track to be pl...

  • Page 411

    • turn the tune control knob to list the top-menu item to be selected and push the tune control knob. This will display the next sub-menu list item on the audio device, then follow the same steps to go to the desired track in that list. Not all ipod or external usb device sub-menu levels are availab...

  • Page 412

    Controlling btsa using radio buttons to enter btsa mode, push either “aux” button on the radio or push the vr button and say “bluetooth streaming audio.” play mode when switched to btsa mode, some audio devices can start playing music over the vehicle’s audio system, but some devices require the mus...

  • Page 413

    Steering wheel audio controls the remote sound system controls are located on the rear surface of the steering wheel. Reach behind the wheel to access the switches. The right-hand control is a rocker-type switch with a push-button in the center and controls the volume and mode of the sound system. P...

  • Page 414

    The button located in the center of the left-hand control will tune to the next preset station that you have pro- grammed in the radio preset button. Cd player pushing the top of the switch once will go to the next track on the cd. Pushing the bottom of the switch once will go to the beginning of th...

  • Page 415

    Note: if you experience difficulty in playing a particular disc, it may be damaged (e.G., scratched, reflective coat- ing removed, a hair, moisture or dew on the disc) oversized, or have protection encoding. Try a known good disc before considering disc player service. Radio operation and mobile dev...

  • Page 416

    The radio manufacturer believes the internal wireless radio is safe for use by consumers. The level of energy emitted is far less than the electromagnetic energy emit- ted by wireless devices such as mobile phones. However, the use of wireless radios may be restricted in some situations or environme...

  • Page 417

    • consult the dealer or an experienced radio technician for help. Climate controls the air conditioning and heating system is designed to make you comfortable in all types of weather. Manual heating and air conditioning the manual temperature controls consist of a series of outer rotary dials and in...

  • Page 418

    Note: if your air conditioning performance seems lower than expected, check the front of the a/c condenser located in front of the radiator for an accumulation of dirt or insects. Clean with a gentle water spray from behind the radiator and through the condenser. Fabric front fascia protectors may r...

  • Page 419

    • panel air is directed through the outlets in the instru- ment panel. These outlets can be adjusted to direct airflow. Note: the center instrument panel outlets can be aimed so that they are directed toward the rear seat passengers for maximum airflow to the rear. • bi-level air is directed through...

  • Page 420

    Note: the air conditioning compressor operates in mix, defrost, or a blend of these modes, even if the air conditioning (a/c) button is not pushed. This dehu- midifies the air to help dry the windshield. To improve fuel economy, use these modes only when necessary. Recirculation control pushing the ...

  • Page 421

    Automatic temperature control (atc) — if equipped automatic operation the automatic temperature control system automati- cally maintains the climate in the cabin of the vehicle at the comfort levels desired by the driver and passenger. Operation of the system is quite simple. Turn the mode control k...

  • Page 422

    You will experience the greatest efficiency by simply allowing the system to function automatically. Selecting the “o” (off) position on the blower control stops the system completely and closes the outside air intake. The recommended setting for maximum comfort is 72° f (22° c) for the average pers...

  • Page 423

    Blower control for full automatic operation or for automatic blower operation, turn the knob to the auto position. In manual mode, there are seven blower speeds that can be individually selected. In off position, the blower will shut off. Manual operation this system offers a full complement of manu...

  • Page 424

    422 understanding your instrument panel.

  • Page 425

    The operator can override the auto mode setting to change airflow distribution by rotating the mode control knob (on the right) to one of the following positions: • panel air is directed through the outlets in the instru- ment panel. These outlets can be adjusted to direct airflow. Note: the center ...

  • Page 426

    • defrost air is directed through the windshield and side window demist outlets. Use this mode with maxi- mum blower and temperature settings for best wind- shield and side window defrosting. • air conditioner control push this button to turn on the air conditioning during manual operation only. Whe...

  • Page 427

    • extended use of recirculation may cause the windows to fog. If the interior of the windows begins to fog, push the recirculation button to return to outside air. Some temp/humidity conditions will cause captured interior air to condense on windows and hamper visibility. For this reason, the system...

  • Page 428

    Winter operation use of the air recirculation mode during winter months is not recommended because it may cause window fogging. Vacation storage anytime you store your vehicle, or keep it out of service (i.E., vacation) for two weeks or more, run the air conditioning system at idle for about five mi...

  • Page 429

    Side window demisters a side window demister outlet is located at each end of the instrument panel. These non-adjustable outlets direct air toward the side windows when the system is in the floor, mix, or defrost mode. The air is directed at the area of the windows through which you view the outside...

  • Page 430

    Control setting suggestions for various weather conditions 428 understanding your instrument panel.

  • Page 431: Starting And Operating

    Starting and operating contents 䡵 starting procedures . . . . . . . . . . . . . . . .434 ▫ manual transmission — if equipped . . . . . . .434 ▫ automatic transmission — if equipped . . . . .434 ▫ normal starting. . . . . . . . . . . . . . . . . . . . . . .435 ▫ extreme cold weather (below –22°f or −...

  • Page 432

    䡵 autostick . . . . . . . . . . . . . . . . . . . . . . . . . .451 ▫ operation . . . . . . . . . . . . . . . . . . . . . . . . . . .452 䡵 four–wheel drive operation (command-trac i or rock-trac) . . . . . .453 ▫ operating instructions/precautions . . . . . . . .454 ▫ shift positions . . . . . . . . ...

  • Page 433

    䡵 brake system . . . . . . . . . . . . . . . . . . . . . . .480 䡵 electronic brake control system . . . .481 ▫ electronic brake force distribution (ebd) . . . .481 ▫ brake system warning light. . . . . . . . . . . . . .481 ▫ anti-lock brake system (abs) . . . . . . . . . . . .482 ▫ anti-lock brake w...

  • Page 434

    ▫ tire spinning . . . . . . . . . . . . . . . . . . . . . . . .517 ▫ tread wear indicators . . . . . . . . . . . . . . . . . .518 ▫ life of tire . . . . . . . . . . . . . . . . . . . . . . . . .519 ▫ replacement tires . . . . . . . . . . . . . . . . . . . . .519 䡵 tire chains (traction devices) . . ...

  • Page 435

    ▫ trailer hitch classification . . . . . . . . . . . . . . .546 ▫ trailer towing weights (maximum trailer weight ratings) . . . . . . . . . . . . . . . . . . . . . .548 ▫ trailer and tongue weight . . . . . . . . . . . . . .555 ▫ towing requirements . . . . . . . . . . . . . . . . . .556 ▫ towing ti...

  • Page 436

    Starting procedures before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. Warning! • when leaving the vehicle, always remove the key fob from the ignition and lock your vehicle. • never leave children alone in a vehicle, or with access to...

  • Page 437

    Normal starting note: normal starting of either a cold or a warm engine is obtained without pumping or pressing the accelerator pedal. Cycle the ignition switch to the start position and release when the engine starts. If the engine fails to start within 10 seconds, cycle the ignition switch to the ...

  • Page 438

    Warning! (continued) • do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic trans- mission cannot be started this way. Unburned fuel could enter the catalytic converter and, once the engine has started, ignite and damage the converter and vehicle. • if th...

  • Page 439

    With tip start — automatic transmission only if the engine fails to start after you have followed the “normal starting” or “extreme cold weather” proce- dures, it may be flooded. To clear any excess fuel, push the accelerator pedal all the way to the floor and hold it. Then, turn the ignition switch...

  • Page 440

    Warning! Remember to disconnect the engine block heater cord before driving. Damage to the 110-115 volt ac electrical cord could cause electrocution. Manual transmission — if equipped warning! You or others could be injured if you leave the vehicle unattended without having the parking brake fully a...

  • Page 441

    Shifting fully press the clutch pedal before shifting gears. As you release the clutch pedal, lightly press the accelerator pedal. You should always use first gear when starting from a standing position. Recommended vehicle shift speeds to utilize your manual transmission efficiently for both fuel e...

  • Page 442

    Manual transmission shift speeds in mph (km/h) engine speeds 1 to 2 2 to 3 3 to 4 4 to 5 5 to 6 3.6l accel. 15 (24) 24 (39) 34 (55) 47 (76) 56 (90) cruise 10 (16) 19 (31) 27 (43) 37 (60) 41 (66) note: vehicle speeds shown in the chart above are for 2h and 4h only, vehicle speeds in 4l would be signi...

  • Page 443

    Caution! • skipping gears and downshifting into lower gears at higher vehicle speeds can damage the engine and clutch systems, any attempt to shift into lower gear with clutch pedal depressed may result dam- age to the clutch system. Shifting into lower gear and releasing the clutch may result in en...

  • Page 444

    Manual transmission downshift speeds in mph (km/h) gear selection 6 to 5 5 to 4 4 to 3 3 to 2 2 to 1 maximum speed 80 (129) 70 (113) 50 (81) 30 (48) 15 (24) note: vehicle speeds shown in the chart above are for 2h and 4h only, vehicle speeds in 4l would be signifi- cantly less. Reverse shifting to s...

  • Page 445

    Caution! (continued) • before shifting into any gear, make sure your foot is firmly pressing the brake pedal. Note: you must press and hold the brake pedal while shifting out of park. Warning! • it is dangerous to shift out of park or neutral if the engine speed is higher than idle speed. If your fo...

  • Page 446

    Warning! (continued) warned not to touch the parking brake, brake pedal or the transmission gear selector. • do not leave the ignition key in or near the vehicle (or in a location accessible to children). A child could operate power windows, other controls, or move the vehicle. Key ignition park int...

  • Page 447

    Five-speed automatic transmission — if equipped the transmission gear position display (located in the instrument cluster) indicates the transmission gear range. You must press the brake pedal to move the shift lever out of park (refer to “brake/transmission shift inter- lock system” in this section...

  • Page 448

    Gear ranges do not race the engine when shifting from park or neutral into another gear range. Note: • after selecting any gear range, wait a moment to allow the selected gear to engage before accelerating. This is especially important when the engine is cold. • if there is a need to restart the eng...

  • Page 449

    Warning! • never use the park position as a substitute for the parking brake. Always apply the parking brake fully when parked to guard against vehicle move- ment and possible injury or damage. • your vehicle could move and injure you and others if it is not in park. Check by trying to move the gear...

  • Page 450

    Warning! (continued) locked in park, securing the vehicle against un- wanted movement. • when leaving the vehicle, always remove the igni- tion key from the vehicle and lock the vehicle. • never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a ve...

  • Page 451

    • look at the transmission gear position display and verify that it indicates the park position (p). • with brake pedal released, verify that the shift lever will not move out of park. Reverse (r) this range is for moving the vehicle backward. Shift into reverse only after the vehicle has come to a ...

  • Page 452

    Drive (d) this range should be used for most city and highway driving. It provides the smoothest upshifts and down- shifts, and the best fuel economy. The transmission automatically upshifts through underdrive first, second, and third gears, direct fourth gear and overdrive fifth gear. The drive pos...

  • Page 453

    2. Shift the transmission into park. 3. Turn the ignition switch to the lock/off position. 4. Wait approximately 10 seconds. 5. Restart the engine. 6. Shift into the desired gear range. If the problem is no longer detected, the transmission will return to normal operation. Note: even if the transmis...

  • Page 454

    This system can also provide you with more control during passing, city driving, cold slippery conditions, mountain driving, trailer towing, and many other situa- tions. Operation when the shift lever is in the drive position, the transmission will operate automatically, shifting between the five av...

  • Page 455

    • you can start out, from a stop, in first or second gear. Tapping (+) (at a stop) will allow starting in second gear. Starting out in second gear can be helpful in snowy or icy conditions. • the system will ignore attempts to upshift at too low of a vehicle speed. • avoid using speed control when a...

  • Page 456

    Operating instructions/precautions the transfer case provides four mode positions: • 2h (two-wheel drive high range) • 4h (four-wheel drive high range) • n (neutral) • 4l (four-wheel drive low range) the transfer case is intended to be driven in the 2h position for normal street and highway conditio...

  • Page 457

    Rear wheels to rotate at the same speed. The 4h and 4l positions are intended for loose, slippery road surfaces only and not intended for normal driving. Driving in the 4h and 4l positions on hard-surfaced roads will cause increased tire wear and damage to the driveline compo- nents. Refer to “shift...

  • Page 458

    Warning! (continued) the parking brake. The transfer case neutral (n) position disengages both the front and rear drive shaft from the powertrain, and will allow the vehicle to roll, even if the automatic transmission is in park (or manual transmission is in gear). The parking brake should always be...

  • Page 459

    Speed. This range (4l) provides additional traction and maximum pulling power for loose, slippery road surfaces only. Do not exceed 25 mph (40 km/h). Caution! Exceeding 25 mph (40 km/h) while the transfer case is engaged in 4l may result in an engine overspeed condition and engine damage. The “4wd i...

  • Page 460

    Note: shifting into or out of 4l is possible with the vehicle completely stopped; however, difficulty may oc- cur due to the mating teeth not being properly aligned. Several attempts may be required for clutch teeth align- ment and shift completion to occur. The preferred method is with the vehicle ...

  • Page 461

    Warning! Onvehicles equipped with a limited-slip differential, never run the engine with one rear wheel off the ground. The vehicle may drive through the rear wheel remaining on the ground and cause you to lose control of your vehicle. Axle lock (tru–lok) — rubicon models the axle lock switch is loc...

  • Page 462

    To activate the system, push the bottom of the axle lock switch once to lock the rear axle only (the “rear axle lock indicator light” will illuminate), push the bottom of the switch again to lock the front axle (the “front axle lock indicator light” will illuminate). When the rear axle is locked, pu...

  • Page 463

    Push the sway bar switch to activate the system. Push the switch again to deactivate the system. The “sway bar indicator light” (located in the instrument cluster) will illuminate when the bar is disconnected. The “sway bar indicator light” will flash during activation transition, or when activation...

  • Page 464

    To disconnect the stabilizer/sway bar, shift to either 4h or 4l and push the sway bar switch to obtain the off-road position. Refer to “four-wheel drive operation” in “starting and operating” for further information. The “sway bar indicator light” will flash until the stabilizer/ sway bar has been f...

  • Page 465

    An advantage of the higher ground clearance is a better view of the road, allowing you to anticipate problems. They are not designed for cornering at the same speeds as conventional two-wheel drive vehicles any more than low-slung sports cars are designed to perform satisfacto- rily in off-road cond...

  • Page 466

    3. Remove the side step assembly. The basics of off-road driving you will encounter many types of terrain driving off- road. You should be familiar with the terrain and area before proceeding. There are many types of surface conditions: hard-packed dirt, gravel, rocks, grass, sand, mud, snow and ice...

  • Page 467

    Warning! Always wear your seat belt and firmly tie down cargo. Unsecured cargo can become projectiles in an off-road situation. When to use 4l (low) range when off-road driving, shift into 4l (low) for additional traction and control on slippery or difficult terrain, ascending or descending steep hi...

  • Page 468

    Driving in snow, mud and sand snow in heavy snow or for additional control and traction at slower speeds, shift the transmission into a low gear and the transfer case into 4l (low) if necessary. Do not shift to a lower gear than necessary to maintain headway. Over- revving the engine can spin the wh...

  • Page 469

    Key to driving in soft sand is using the appropriate tire pressure, accelerating slowly, avoiding abrupt maneu- vers and maintaining the vehicle’s momentum. If you are going to be driving on large soft sandy areas or dunes, reduce your tire pressure to a minimum of 15 psi (103 kpa) to allow for a gr...

  • Page 470

    Using a spotter there are many times where it is hard to see the obstacle or determine the correct path. Determining the correct path can be extremely difficult when you are confronting many obstacles. In these cases have someone guide you over, through, or around the obstacle. Have the person stand...

  • Page 471

    You should now be able to drive out following the trench you just created at a 45-degree angle. Warning! There is an increased risk of rollover when crossing an obstacle, at any angle, with steep sides. Crossing logs to cross a log, approach it at a slight angle (approxi- mately 10 to 15 degrees). T...

  • Page 472

    Caution! Winching or rocking the vehicle off hard objects increases the risk of underbody damage. Hill climbing hill climbing requires good judgment and a good under- standing of your abilities and your vehicle’s limitations. Hills can cause serious problems. Some are just too steep to climb and sho...

  • Page 473

    And maintain headway by turning the steering wheel no more than a 1/4 turn quickly back and forth. This will provide a fresh ⬙ bite ⬙ into the surface and will usually provide enough traction to complete the climb. If you do not make it to the top, place the vehicle in reverse and back straight down...

  • Page 474

    Which increases the possibilities of a downhill slide or rollover. Make sure the surface has good traction with firm and stable soils. If possible, transverse the incline at an angle heading slightly up or down. Warning! Driving across an incline increases the risk of a rollover, which may result in...

  • Page 475

    Your vehicle’s abilities and be able to recover it if something goes wrong. You should never stop or shut a vehicle off when crossing deep water unless you ingested water into the engine air intake. If the engine stalls, do not attempt to restart it. Determine if it has ingested water first. The key...

  • Page 476

    Waters; check for hidden obstacles. Make sure you will not be intruding on any wildlife, and you can recover the vehicle if necessary. The key to a safe crossing is the water depth, current and bottom conditions. On soft bottoms, the vehicle will sink in, effectively increasing the water level on th...

  • Page 477

    The slowest current can push the heaviest vehicle down- stream and out of control if the water is deep enough to push on the large surface area of the vehicle’s body. Before you proceed, determine the speed of the current, the water’s depth, approach angle, bottom condition and if there are any obst...

  • Page 478

    • after extended operation in mud, sand, water, or similar dirty conditions, have the radiator, fan, brake rotors, wheels, brake linings, and axle yokes inspected and cleaned as soon as possible. Warning! Abrasive material in any part of the brakes may cause excessive wear or unpredictable braking. ...

  • Page 479

    System. This noise should be considered normal, and it does not in any way damage the steering system. Caution! Prolonged operation of the steering system at the end of the steering wheel travel will increase the steering fluid temperature and it should be avoided when possible. Damage to the power ...

  • Page 480

    Parking brake before leaving the vehicle, make sure that the parking brake is fully applied. Also, be certain to leave an automatic transmission in park, or manual transmission in reverse or first gear. The parking brake lever is located in the center console. To apply the parking brake, pull the le...

  • Page 481

    Note: • when the parking brake is applied and the automatic transmission is placed in gear, the “brake warning light” will flash. If vehicle speed is detected, a chime will sound to alert the driver. Fully release the parking brake before attempting to move the vehicle. • this light only shows that ...

  • Page 482

    Warning! (continued) operate power windows, other controls, or move the vehicle. • be sure the parking brake is fully disengaged before driving; failure to do so can lead to brake failure and a collision. • always fully apply the parking brake when leav- ing your vehicle or it may roll and cause dam...

  • Page 483

    In the event power assist is lost for any reason (for example, repeated brake applications with the engine off) the brakes will still function. The effort required to brake the vehicle will be much greater than that required with the power system operating. Electronic brake control system your vehic...

  • Page 484

    Anti-lock brake system (abs) the anti-lock brake system (abs) provides increased vehicle stability and brake performance under most braking conditions. The system automatically prevents wheel lock, and enhances vehicle control during braking. The abs performs a self-check cycle to ensure that the ab...

  • Page 485

    Warning! (continued) press firmly on your brake pedal when you need to slow down or stop. • the abs cannot prevent the natural laws of phys- ics from acting on the vehicle, nor can it increase braking or steering efficiency beyond that afforded by the condition of the vehicle brakes and tires or the...

  • Page 486

    Brake assist system (bas) the bas is designed to optimize the vehicle’s braking capability during emergency braking maneuvers. The system detects an emergency braking situation by sens- ing the rate and amount of brake application and then applies optimum pressure to the brakes. This can help reduce...

  • Page 487

    Does not apply the throttle before this time expires, the system will release brake pressure and the vehicle will roll down the hill as normal. The following conditions must be met in order for hsa to activate: • the feature must be enabled. • the vehicle must be stopped. • park brake must be off. •...

  • Page 488

    Towing with hsa hsa will also provide assistance to mitigate roll back while towing a trailer. Warning! • if you use a trailer brake controller with your trailer, the trailer brakes may be activated and deactivated with the brake switch. If so, there may not be enough brake pressure to hold both the...

  • Page 489

    • if disabling hsa using uconnect settings, refer to “uconnect settings” in “understanding your instru- ment panel” for further information. For vehicles not equipped with the evic, perform the following steps: 1. Center the steering wheel (front wheels pointing straight forward). 2. Shift the trans...

  • Page 490

    Other, the system will apply the brake of the spinning wheel. This will allow more engine torque to be applied to the wheel that is not spinning. Bld may remain enabled even if tcs and esc are in a reduced mode. Electronic stability control (esc) this system enhances directional control and stabilit...

  • Page 491

    Warning! Electronic stability control (esc) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions. Esc cannot prevent accidents, including those resulting from excessive speed in turns, driving on very slippery ...

  • Page 492

    This mode is intended to be used if the vehicle is in deep snow, sand, or gravel conditions and more wheel spin than esc would normally allow is required to gain traction. To turn esc on again, momentarily push the esc off switch. This will restore the normal “esc on” mode of operation. Note: to imp...

  • Page 493

    In the ⬙ esc full off ⬙ mode, the engine torque reduction and stability features are disabled. Therefore, the en- hanced vehicle stability offered by esc is unavailable. In an emergency evasive maneuver, the esc system will not engage to assist in maintaining stability. “esc full off” mode is intend...

  • Page 494

    Warning! (continued) maneuver, the esc and erm systems will not engage to assist in maintaining stability. The ⴖ esc full off ⴖ mode is intended for off-road use only. 4l range (4wd models) esc full off this is the normal operating mode for esc in 4l range. Whenever the vehicle is started in 4l rang...

  • Page 495

    Warning! (continued) maneuver, the esc and erm systems will not engage to assist in maintaining stability. The ⴖ esc full off ⴖ mode is intended for off-road use only. 2h range (4wd models) or 2wd models esc on this is the normal operating mode for esc in 2h range and on 2wd vehicles. Esc partial of...

  • Page 496

    Warning! • when in “partial off” mode, the tcs functionality of esc, (except for the limited slip feature de- scribed in the tcs section), has been disabled and the “esc off indicator light” will be illuminated. When in “partial off” mode, the engine power reduction feature of tcs is disabled, and t...

  • Page 497

    Note: • the “esc activation/malfunction indicator light” and the “esc off indicator light” come on momen- tarily each time the ignition switch is turned on. • each time the ignition is turned on, the esc system will be on even if it was turned off previously. • the esc system will make buzzing or cl...

  • Page 498

    Warning! Many factors, such as vehicle loading, road condi- tions and driving conditions, influence the chance that wheel lift or rollover may occur. Erm cannot prevent all wheel lift or roll overs, especially those that involve leaving the roadway or striking objects or other vehicles. The capabili...

  • Page 499

    Hill descent control (hdc) — if equipped hdc is only intended for low speed off-road driving. Hdc maintains vehicle speed while descending hills in off-road driving conditions by applying the brakes when necessary. The symbol indicates the status of the hill descent control (hdc) feature. The lamp w...

  • Page 500

    However, the driver can override hdc operation by applying the brake to slow the vehicle down below the hdc control speed. If more speed is desired during hdc control, the accelerator pedal will increase vehicle speed in the usual manner. When either the brake or the accelerator is released, hdc wil...

  • Page 501

    Tire safety information tire markings note: • p (passenger) — metric tire sizing is based on u.S. Design standards. P-metric tires have the letter “p” molded into the sidewall preceding the size designa- tion. Example: p215/65r15 95h. • european — metric tire sizing is based on european design stand...

  • Page 502

    • temporary spare tires are designed for temporary emergency use only. Temporary high pressure com- pact spare tires have the letter “t” or “s” molded into the sidewall preceding the size designation. Example: t145/80d18 103m. • high flotation tire sizing is based on u.S. Design standards and it beg...

  • Page 503

    Example: r = construction code – ⬙ r ⬙ means radial construction, or – ⬙ d ⬙ means diagonal or bias construction 15, 16, 18 = rim diameter in inches (in) service description: 95 = load index – a numerical code associated with the maximum load a tire can carry h = speed symbol – a symbol indicating t...

  • Page 504

    Example: load identification: absence of the following load identification symbols on the sidewall of the tire indicates a standard load (sl) tire: • xl = extra load (or reinforced) tire, or • ll = light load tire or • c, d, e, f, g = load range associated with the maximum load a tire can carry at a...

  • Page 505

    Example: dot ma l9 abcd 0301 dot = department of transportation – this symbol certifies that the tire is in compliance with the u.S. Department of transportation tire safety standards and is approved for highway use ma = code representing the tire manufacturing location (two digits) l9 = code repres...

  • Page 506

    Tire terminology and definitions term definition b-pillar the vehicle b-pillar is the structural member of the body located behind the front door. Cold tire inflation pressure cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least three hours,...

  • Page 507

    Tire loading and tire pressure tire and loading information placard location note: the proper cold tire inflation pressure is listed on the driver’s side b-pillar or the rear edge of the driver’s side door. Example tire placard location (door) example tire placard location (b-pillar) 5 starting and ...

  • Page 508

    Tire and loading information placard this placard tells you important information about the: 1. Number of people that can be carried in the vehicle. 2. Total weight your vehicle can carry. 3. Tire size designed for your vehicle. 4. Cold tire inflation pressures for the front, rear, and spare tires. ...

  • Page 509

    Occupants and cargo should never exceed xxx lbs or xxx kg” on the tire and loading information placard. The combined weight of occupants, cargo/luggage and trailer tongue weight (if applicable) should never exceed the weight referenced here. Steps for determining correct load limit 1. Locate the sta...

  • Page 510

    508 starting and operating.

  • Page 511

    Warning! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. Tires — general information tire pressure proper tire inflation pressur...

  • Page 512

    Warning! (continued) • unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left. • always drive with each tire inflated to the recom- mended cold tire inflation pressure. Both under-inflation and over-inflation affect the stability of the v...

  • Page 513

    At least once a month: • check and adjust tire pressure with a good quality pocket-type pressure gauge. Do not make a visual judgement when determining proper inflation. Tires may look properly inflated even when they are under- inflated. • inspect tires for signs of tire wear or visible damage. Cau...

  • Page 514

    Tire pressures for high speed operation the manufacturer advocates driving at safe speeds and within posted speed limits. Where speed limits or condi- tions are such that the vehicle can be driven at high speeds, maintaining correct tire inflation pressure is very important. Increased tire pressure ...

  • Page 515

    Consult an authorized tire dealer for tire repairs and additional information. Damaged run flat tires, or run flat tires that have experienced a loss of pressure should be replaced imme- diately with another run flat tire of identical size and service description (load index and speed symbol). Tire ...

  • Page 516

    Warning! Do not use summer tires in snow/ice conditions. You could lose vehicle control, resulting in severe injury or death. Driving too fast for conditions also creates the possibility of loss of vehicle control. Snow tires some areas of the country require the use of snow tires during the winter....

  • Page 517

    Run flat tire reaches the run flat mode it has limited driving capabilities and needs to be replaced immedi- ately. A run flat tire is not repairable. It is not recommended driving a vehicle loaded at full capacity or to tow a trailer while a tire is in the run flat mode. See the tire pressure monit...

  • Page 518

    Compact spare tire — if equipped the compact spare is for temporary emergency use only. You can identify if your vehicle is equipped with a compact spare by looking at the spare tire description on the tire and loading information placard located on the driver’s side door opening or on the sidewall ...

  • Page 519

    Tire may have limited tread life. When the tread is worn to the tread wear indicators, the temporary use full size spare tire needs to be replaced. Since it is not the same as your original equipment tire, replace (or repair) the original equipment tire and reinstall on the vehicle at the first oppo...

  • Page 520

    Refer to “freeing a stuck vehicle” in “what to do in emergencies” for further information. Warning! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause tire dam- age or failure. A tire could explode and injure some- one. Do not spin your vehicle’s wheels fast...

  • Page 521

    Worn to the tread wear indicators, the tire should be replaced. Refer to “replacement tires” in this section for further information. Life of tire the service life of a tire is dependent upon varying factors including, but not limited to: • driving style. • tire pressure - improper cold tire inflati...

  • Page 522

    Information placard or the vehicle certification label for the size designation of your tire. The load index and speed symbol for your tire will be found on the original equipment tire sidewall. See the tire sizing chart ex- ample found in the “tire safety information” section of this manual for mor...

  • Page 523

    Warning! (continued) • failure to equip your vehicle with tires having adequate speed capability can result in sudden tire failure and loss of vehicle control. Caution! Replacing original tires with tires of a different size may result in false speedometer and odometer read- ings. Tire chains (tract...

  • Page 524

    Caution! (continued) important that only traction devices in good condi- tion are used. Broken devices can cause serious damage. Stop the vehicle immediately if noise occurs that could indicate device breakage. Remove the damaged parts of the device before further use. • install device as tightly as...

  • Page 525

    Caution! Proper operation of four-wheel drive vehicles de- pends on tires of equal size, type and circumference on each wheel. Any difference in tire size can cause (continued) caution! (continued) damage to the transfer case. Tire rotation schedule should be followed to balance tire wear. Tire pres...

  • Page 526

    Also increase as the vehicle is driven; this is normal and there should be no adjustment for this increased pres- sure. The tpms will warn the driver of a low tire pressure if the tire pressure falls below the low pressure warning threshold for any reason, including low temperature effects, or natur...

  • Page 527

    Psi (207 kpa), but the “tire pressure monitoring telltale light” will still be on. In this situation, the “tire pressure monitoring telltale light” will turn off only after the tires have been inflated to the vehicle’s recom- mended cold placard pressure value. Caution! • the tpms has been optimized...

  • Page 528

    • driving on a significantly under-inflated tire causes the tire to overheat and can lead to tire failure. Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability. • the tpms is not a substitute for proper tire mainte- nance, and i...

  • Page 529

    Monitoring telltale light” to illuminate or the chime to sound while stowed in the spare location. The “tire pressure monitoring telltale light” will illuminate in the instrument cluster, a “low tire pressure” message will display in the evic, and an audible chime will be activated when one or more ...

  • Page 530

    3. Lots of snow or ice around the wheels or wheel housings. 4. Using tire chains on the vehicle. 5. Using wheels/tires not equipped with tpm sensors. Vehicles not equipped with evic will inform the driver which tire(s) are low but not provide actual tire pressure. The low tire iso telltale will illu...

  • Page 531

    If you install the spare tire in place of a road tire that has a pressure below the low-pressure warning limit, upon the next ignition key cycle, a chime will sound and the “tire pressure monitoring telltale light” will turn on. After driving the vehicle for up to 20 minutes above 15 mph (24 km/h), ...

  • Page 532

    Note: it is particularly important, for you to regularly check the tire pressure in all of your tires and to maintain the proper pressure. The tire pressure monitor system (tpms) consists of the following components: • receiver module • four tire pressure monitoring sensors • various tire pressure m...

  • Page 533

    Should a low tire condition occur on any of the four active road tire(s), you should stop as soon as possible, and inflate the low tire(s) that is “flashing” on the graphic display to the vehicle’s recommended cold tire pressure inflation value shown in the “inflate to xx” message. The system will a...

  • Page 534

    In place of the pressure value(s), indicating which tire pressure monitoring sensor(s) is not being received. If the ignition switch is cycled, this sequence will repeat, providing the system fault still exists. If the system fault no longer exists, the “tire pressure monitoring telltale light” will...

  • Page 535

    • if your vehicle is not equipped with a matching full-size spare wheel and tire assembly, it does not have a tire pressure monitoring sensor in the spare tire. The tpms will not be able to monitor the tire pressure. If you install the spare tire in place of a road tire that has a pressure below the...

  • Page 536

    General information this device complies with part 15 of the fcc rules and rss-210 of industry canada. Operation is subject to the following two conditions: (1) this device may not cause harmful interference. (2) this device must accept any interference received, including interference that may caus...

  • Page 537

    Than 87 can cause engine failure and may void or not be covered by the new vehicle limited warranty. Poor quality gasoline can cause problems such as hard starting, stalling, and hesitations. If you experience these symptoms, try another brand of gasoline before consid- ering service for the vehicle...

  • Page 538

    Problems that result from using gasoline containing more than 15% ethanol (e-15) or gasoline containing methanol are not the responsibility of the manufacturer and may void or not be covered under new vehicle limited warranty. E-85 usage in non-flex fuel vehicles non-flex fuel vehicles (ffv) are com...

  • Page 539

    Materials added to fuel besides using unleaded gasoline with the proper octane rating, gasolines that contain detergents, corrosion and stability additives are recommended. Using gasolines that have these additives will help improve fuel economy, reduce emissions, and maintain vehicle perfor- mance....

  • Page 540

    Caution! (continued) • the use of fuel additives, which are now being sold as octane enhancers, is not recommended. Most of these products contain high concentrations of methanol. Fuel system damage or vehicle perfor- mance problems resulting from the use of such fuels or additives is not the respon...

  • Page 541

    Warning! (continued) time the vehicle is raised. Have any abnormal conditions repaired promptly. Until repaired, drive with all side windows fully open. Adding fuel fuel filler cap the fuel filler cap is located on the driver’s side of the vehicle. If the fuel filler cap is lost or damaged, be sure ...

  • Page 542

    Caution! (continued) into the fuel system. Also, a poorly fitting aftermar- ket cap can cause the “malfunction indicator light (mil)” to illuminate, due to fuel vapors escaping from the system. • to avoid fuel spillage and overfilling, do not “top off” the fuel tank after filling. Warning! • never h...

  • Page 543

    Loose fuel filler cap message after fuel has been added, the vehicle diagnostic system can determine if the fuel filler cap is possibly loose, improperly installed, or damaged. If the system detects a malfunction, the “gascap” message will display in the odometer display. Tighten the gas cap until a...

  • Page 544

    Rear axle systems (gawr). Total load must be limited so gvwr and front and rear gawr are not exceeded. Payload the payload of a vehicle is defined as the allowable load weight a truck can carry, including the weight of the driver, all passengers, options and cargo. Gross axle weight rating (gawr) th...

  • Page 545

    Values are determined by weighing your vehicle on a commercial scale before any occupants or cargo are added. Loading the actual total weight and the weight of the front and rear of your vehicle at the ground can best be determined by weighing it when it is loaded and ready for operation. The entire...

  • Page 546

    Trailer towing in this section you will find safety tips and information on limits to the type of towing you can reasonably do with your vehicle. Before towing a trailer, carefully review this information to tow your load as efficiently and safely as possible. To maintain the new vehicle limited war...

  • Page 547

    Gross axle weight rating (gawr) the gawr is the maximum capacity of the front and rear axles. Distribute the load over the front and rear axles evenly. Make sure that you do not exceed either front or rear gawr. Refer to “vehicle loading/vehicle certifica- tion label” in “starting and operating” for...

  • Page 548

    Of hitches are the most popular on the market today and they are commonly used to tow small and medium sized trailers. Weight-distributing hitch a weight-distributing system works by applying lever- age through spring (load) bars. They are typically used for heavier loads to distribute trailer tongu...

  • Page 549

    Trailer hitch classification definitions class max. Trailer hitch industry standards class i - light duty 2,000 lbs (907 kg) class ii - medium duty 3,500 lbs (1 587 kg) class iii - heavy duty 5,000 lbs (2 267 kg) class iv - extra heavy duty 10,000 lbs (4 535 kg) refer to the “trailer towing weights ...

  • Page 550

    Trailer towing weights (maximum trailer weight ratings) engine/ transmission axle model gcwr (gross com- bined wt. Rating) frontal area max. Gtw (gross trailer wt.) max. Trailer tongue wt. (see note) 3.6l/manual 3.21 two–door sport model (4wd) 6,900 lbs (3 130 kg) 25 sq ft (2.32 sq m) 2,000 lbs (907...

  • Page 551

    Engine/ transmission axle model gcwr (gross com- bined wt. Rating) frontal area max. Gtw (gross trailer wt.) max. Trailer tongue wt. (see note) 3.6l/manual 3.21 two–door sahara model (4wd) 7,000 lbs (3 175 kg) 25 sq ft (2.32 sq m) 2,000 lbs (907 kg) 200 lbs (91 kg) 3.6l/manual 3.73 two–door sahara m...

  • Page 552

    Engine/ transmission axle model gcwr (gross com- bined wt. Rating) frontal area max. Gtw (gross trailer wt.) max. Trailer tongue wt. (see note) 3.6l/ automatic 3.73 two–door sahara model (4wd) 8,500 lbs (3 856 kg) 25 sq ft (2.32 sq m) 3,500 lbs (1 587 kg) 350 lbs (158 kg) 3.6l/manual 4.10 two–door r...

  • Page 553

    Engine/ transmission axle model gcwr (gross com- bined wt. Rating) frontal area max. Gtw (gross trailer wt.) max. Trailer tongue wt. (see note) 3.6l/ automatic 4.10 two–door rubicon model (4wd) 8,600 lbs (3 900 kg) 25 sq ft (2.32 sq m) 3,500 lbs (1 587 kg) 350 lbs (158 kg) 3.6l/manual 3.21 four–door...

  • Page 554

    Engine/ transmission axle model gcwr (gross com- bined wt. Rating) frontal area max. Gtw (gross trailer wt.) max. Trailer tongue wt. (see note) 3.6l/ automatic 3.73 four–door sport model (4wd) 8,900 lbs (4 037 kg) 32 sq ft (2.97 sq m) 3,500 lbs (1 587 kg) 350 lbs (158 kg) 3.6l/manual 3.21 four–door ...

  • Page 555

    Engine/ transmission axle model gcwr (gross com- bined wt. Rating) frontal area max. Gtw (gross trailer wt.) max. Trailer tongue wt. (see note) 3.6l/ automatic 3.21 four–door sahara model (4wd) 7,500 lbs (3 402 kg) 32 sq ft (2.97 sq m) 2,000 lbs (907 kg) 200 lbs (91 kg) 3.6l/ automatic 3.73 four–doo...

  • Page 556

    Engine/ transmission axle model gcwr (gross com- bined wt. Rating) frontal area max. Gtw (gross trailer wt.) max. Trailer tongue wt. (see note) 3.6l/ automatic 3.73 four–door rubicon model (4wd) 9,200 lbs (4 173 kg) 32 sq ft (2.97 sq m) 3,500 lbs (1 587 kg) 350 lbs (158 kg) 3.6l/ automatic 4.10 four...

  • Page 557

    Note: the trailer tongue weight must be considered as part of the combined weight of occupants and cargo (ie. The gvwr), and the gvwr should never exceed the weight referenced on the tire and loading information placard. Refer to “tire safety information” in “starting and operating” for further info...

  • Page 558

    Note: remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options or dealer-installed options must be considered as part of the total load on your vehicle. Refer to the “tire and loading information” placard for the maximum combine...

  • Page 559

    Warning! (continued) cargo that is not fully secured, dynamic load shifts can occur that may be difficult for the driver to control. You could lose control of your vehicle and have a collision. • when hauling cargo or towing a trailer, do not overload your vehicle or trailer. Overloading can cause a...

  • Page 560

    Towing requirements — tires • proper tire inflation pressures are essential to the safe and satisfactory operation of your vehicle. Refer to “tires – general information” in “starting and oper- ating” for proper tire inflation procedures. • check the trailer tires for proper tire inflation pres- sur...

  • Page 561

    Warning! • donot connect trailer brakes to your vehicle’s hy- draulic brake lines. It can overload your brake system and cause it to fail. You might not have brakes when you need them and could have a collision. • towing any trailer will increase your stopping distance. When towing you should allow ...

  • Page 562

    The trailer tow package will include a four–pin wiring harness. Use a factory-approved trailer harness and connector. Note: do not cut or splice wiring into the vehicles wiring harness. The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector. R...

  • Page 563

    Towing tips before setting out on a trip, practice turning, stopping and backing the trailer in an area away from heavy traffic. If using a manual transmission vehicle for trailer towing, all starts must be in first gear to avoid excessive clutch slippage. Automatic transmission — if equipped the dr...

  • Page 564

    Autostick — if equipped • when using the autostick shift control, select the highest gear that allows for adequate performance and avoids frequent downshifts. For example, choose “4” if the desired speed can be maintained. Choose “3” or “2” if needed to maintain the desired speed. • to prevent exces...

  • Page 565

    Recreational towing (behind motorhome, etc.) towing this vehicle behind another vehicle towing condition wheels off the ground four-wheel drive models flat tow none see instructions • automatic transmission in park • manual transmission in gear (not in neutral [n]) • transfer case in neutral (n) • t...

  • Page 566

    Recreational towing — four-wheel drive models note: the transfer case must be shifted into neutral (n), automatic transmission must be shifted into park, and manual transmission must be placed in gear (not in neutral) for recreational towing. Caution! • do not dolly tow any 4wd vehicle. Towing with ...

  • Page 567

    Shifting into neutral (n) use the following procedure to prepare your vehicle for recreational towing. Warning! You or others could be injured or killed if you leave the vehicle unattended with the transfer case in the neutral (n) position without first fully engaging the parking brake. The transfer...

  • Page 568

    7. Shift the transmission into reverse. 8. Release the brake pedal (and clutch pedal on manual transmissions) for five seconds and ensure that there is no vehicle movement. 9. Repeat steps 7 and 8 with automatic transmission in drive or manual transmission in first gear. 10. Turn the engine off. 11....

  • Page 569

    Shifting out of neutral (n) use the following procedure to prepare your vehicle for normal usage. 1. Bring the vehicle to a complete stop, leaving it con- nected to the tow vehicle. 2. Firmly apply the parking brake. 3. Turn the ignition switch to the lock position. 4. Turn the ignition switch to th...

  • Page 571: Contents

    What to do in emergencies contents 䡵 hazard warning flashers . . . . . . . . . . .570 䡵 if your engine overheats . . . . . . . . . . . .570 䡵 wheel and tire torque specifications . . . . . . . . . . . . . . . . . . . . . .571 ▫ torque specifications . . . . . . . . . . . . . . . . . . .572 䡵 jacking...

  • Page 572

    Hazard warning flashers the hazard warning flasher switch is located on the instrument panel below the climate controls. Push the switch to turn on the hazard warning flasher. When the switch is activated, all direc- tional turn signals will flash on and off to warn oncoming traffic of an emergency....

  • Page 573

    Note: there are steps that you can take to slow down an impending overheat condition: • if your air conditioner (a/c) is on, turn it off. The a/c system adds heat to the engine cooling system and turning the a/c off can help remove this heat. • you can also turn the temperature control to maximum he...

  • Page 574

    Torque specifications lug nut/bolt torque **lug nut/ bolt size lug nut/ bolt socket size 100 ft-lbs (135 n·m) 1/2” x 20 19 mm **use only your authorized dealer recommended lug nuts/bolts and clean or remove any dirt or oil before tightening. Inspect the wheel mounting surface prior to mounting the t...

  • Page 575

    After 25 miles (40 km) check the lug nut/bolt torque to be sure that all the lug nuts/bolts are properly seated against the wheel. Warning! To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts fully until the vehicle has been lowered. Failure to follow this warning may ...

  • Page 576

    Warning! (continued) under a vehicle that is on a jack. If you need to get under a raised vehicle, take it to a service center where it can be raised on a lift. • never start or run the engine while the vehicle is on a jack. • the jack is designed to be used as a tool for changing tires only. The ja...

  • Page 577

    Spare tire removal to remove the spare tire from the carrier, remove the tire cover, if equipped, and remove the lug nuts with the lug wrench turning them counterclockwise. Note: if you have added aftermarket accessories to the spare tire mounted carrier, it cannot exceed a gross weight of 85 lbs (3...

  • Page 578

    4. Shift the automatic transmission into park, or a manual transmission into reverse. 5. Turn the ignition to lock. 6. Block both the front and rear of the wheel diagonally opposite of the jacking position. For ex- ample, if changing the right front tire, block the left rear wheel. Note: passengers ...

  • Page 579

    Warning! (continued) • do not let anyone sit in the vehicle when it is on a jack. • do not get under the vehicle when it is on a jack. If you need to get under a raised vehicle, take it to a service center where it can be raised on a lift. • only use the jack in the positions indicated and for lifti...

  • Page 580

    2. Loosen (but do not remove) the wheel lug nuts by turning them to the left one turn while the wheel is still on the ground. 3. Assemble the jack and jacking tools. Connect the jack handle driver to the extension, then to the lug wrench. 4. Operate the jack from the front or the rear of the vehicle...

  • Page 581

    5. Raise the vehicle by turning the jack screw clockwise. Raise the vehicle only until the tire just clears the surface and enough clearance is obtained to install the spare tire. Minimum tire lift provides maximum sta- bility. Warning! Raising the vehicle higher than necessary can make the vehicle ...

  • Page 582

    8. Lower the vehicle by turning the jack screw to the left, and remove the jack. 9. Finish tightening the lug nuts. Push down on the wrench while tightening for increased leverage. Alter- nate nuts until each nut has been tightened twice. Refer to “torque specifications” in this section for correct ...

  • Page 583

    Each nut has been tightened twice. For the correct lug nut torque refer to “torque specifications” in this section. If in doubt about the correct tightness, have them checked with a torque wrench by your autho- rized dealer or service station. 5. After 25 miles (40 km) check the lug nut torque with ...

  • Page 584

    Preparations for jump-start the battery in your vehicle is located in the right rear of the engine compartment, behind the power distribution center. Warning! • take care to avoid the radiator cooling fan when- ever the hood is raised. It can start anytime the ignition switch is on. You can be injur...

  • Page 585

    3. If using another vehicle to jump-start the battery, park the vehicle within the jumper cables reach, set the parking brake and make sure the ignition is off. Warning! Do not allow vehicles to touch each other as this could establish a ground connection and personal injury could result. Jump start...

  • Page 586

    4. Connect the opposite end of the negative (-) jumper cable to a good engine ground (exposed metal part of the discharged vehicle’s engine) away from the battery and the fuel injection system. Warning! Do not connect the jumper cable to the negative (-) post of the discharged battery. The resulting...

  • Page 587

    If frequent jump starting is required to start your vehicle you should have the battery and charging system in- spected at your authorized dealer. Caution! Accessories plugged into the vehicle power outlets draw power from the vehicle’s battery, even when not in use (i.E., cellular devices, etc.). E...

  • Page 588

    Note: push the ⬙ esc off ⬙ switch, to place the electronic stability control (esc) system in ⬙ partial off ⬙ mode, before rocking the vehicle. Refer to “electronic brake control” in “starting and operating” for further infor- mation. Once the vehicle has been freed, push the ⬙ esc off ⬙ switch again...

  • Page 589

    Caution! Tow hooks are for emergency use only, to rescue a vehicle stranded off road. Do not use tow hooks for tow truck hookup or highway towing. You could damage your vehicle. Tow straps are recommended when towing the vehicle, chains may cause vehicle damage. Warning! • do not use a chain for fre...

  • Page 590

    5. Push and maintain firm pressure on the brake pedal. 6. Insert the screwdriver or similar tool into the access port, and push and hold the override release lever down. 7. Move the gear selector to the neutral position. 8. The vehicle may then be started in neutral. 9. Reinstall the gear selector o...

  • Page 591

    Towing a disabled vehicle this section describes procedures for towing a disabled vehicle using a commercial towing service. If the trans- mission and drivetrain are operable, disabled vehicles may also be towed as described under “recreational towing” in the “starting and operating” section. Towing...

  • Page 592

    If you must use the accessories (wipers, defrosters, etc.) while being towed, the ignition must be in the on/run position, not the acc position. If the vehicle’s battery is discharged, refer to “gear selector override” in this section for instructions on shifting the automatic transmission out of pa...

  • Page 593

    If flatbed equipment is not available and the transfer case is operable, the vehicle may be towed (in the forward direction, with all wheels on the ground), if the transfer case is in neutral (n) and the transmission is in park (for automatic transmissions) or in gear ( not in neutral , for manual t...

  • Page 595: Maintaining Your Vehicle

    Maintaining your vehicle contents 䡵 engine compartment — 3.6l . . . . . . . . . .595 䡵 onboard diagnostic system — obd ii . .596 ▫ loose fuel filler cap message . . . . . . . . . . . .596 䡵 emissions inspection and maintenance programs . . . . . . . . . . . . .597 䡵 replacement parts . . . . . . . ....

  • Page 596

    ▫ automatic transmission — if equipped . . . . .632 ▫ clutch hydraulic system (manual transmission) — if equipped. . . . . . .635 ▫ manual transmission — if equipped . . . . . . .636 ▫ transfer case . . . . . . . . . . . . . . . . . . . . . . . .637 ▫ front/rear axle fluid . . . . . . . . . . . . . ...

  • Page 597

    Engine compartment — 3.6l 1 — integrated power module (fuses) 7 — washer fluid reservoir 2 — battery 8 — engine coolant reservoir 3 — engine oil dipstick 9 — air cleaner filter 4 — automatic transmission dipstick (under engine cover) 10 — coolant pressure cap 5 — engine oil fill 11 — power steering ...

  • Page 598

    Onboard diagnostic system — obd ii your vehicle is equipped with a sophisticated onboard diagnostic system called obd ii. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide ex...

  • Page 599

    The message will appear the next time the vehicle is started. This might indicate a damaged cap. If the prob- lem is detected twice in a row, the system will turn on the mil. Resolving the problem will turn the mil off. Emissions inspection and maintenance programs in some localities, it may be a le...

  • Page 600

    3. Approximately 15 seconds later, one of two things will happen: • the mil will flash for about 10 seconds and then return to being fully illuminated until you turn off the ignition or start the engine. This means that your vehicle’s obd ii system is not ready and you should not proceed to the i/m ...

  • Page 601

    Dealer service your authorized dealer has the qualified service person- nel, special tools, and equipment to perform all service operations in an expert manner. Service manuals are available which include detailed service information for your vehicle. Refer to these service manuals before attempting...

  • Page 602

    Caution! (continued) • your vehicle has been built with improved fluids that protect the performance and durability of your vehicle and also allow extended maintenance inter- vals. Do not use chemical flushes in these compo- nents as the chemicals can damage your engine, transmission, or air conditi...

  • Page 603

    Note: under no circumstances should oil change inter- vals exceed 10,000 miles (16,000 km), twelve months or 350 hours of engine run time, whichever comes first. The 350 hours of engine run or idle time is generally only a concern for fleet customers. Engine oil selection for best performance and ma...

  • Page 604

    Engine oil viscosity — 3.6l engine mopar sae 5w-20 engine oil approved to fca material standard ms-6395 such as pennzoil, shell helix or equivalent is recommended for all operating tempera- tures. This engine oil improves low temperature starting and vehicle fuel economy. The engine oil filler cap a...

  • Page 605

    Indiscriminately discarded, can present a problem to the environment. Contact your authorized dealer, service station or governmental agency for advice on how and where used oil and oil filters can be safely discarded in your area. Engine oil filter the engine oil filter should be replaced with a ne...

  • Page 606

    Engine air cleaner filter selection the quality of replacement engine air cleaner filters varies considerably. Only high quality filters should be used to assure most efficient service. Mopar engine air cleaner filters are a high quality filter and are recom- mended. Engine air cleaner filter inspec...

  • Page 607

    2. Remove air hose and loosen clean air hose clamp then release the spring clips on the air intake cover. 3. Lift the air cleaner cover to access the air cleaner filter. Air cleaner filter cover 1 — spring clips 2 — air hose 3 — clean air hose clamp air cleaner air hose 1 — air filter cleaner cover ...

  • Page 608

    4. Remove the air cleaner filter element from the housing assembly. Engine air cleaner filter installation note: inspect and clean the housing if dirt or debris is present before replacing the air filter element. 1. Install the air cleaner filter element into the housing assembly with the air cleane...

  • Page 609

    Accessory drive belt inspection warning! • do not attempt to inspect an accessory drive belt with vehicle running. • when working near the radiator cooling fan, dis- connect the fan motor lead. The fan is temperature controlled and can start at any time regardless of ignition switch position. You co...

  • Page 610

    Conditions that would require replacement: • rib chunking (one or more ribs has separated from belt body) • rib or belt wear • longitudinal belt cracking (cracks between two ribs) • belt slips • “groove jumping ⬙ (belt does not maintain correct position on pulley) • belt broken (note: identify and c...

  • Page 611

    Maintenance-free battery your vehicle is equipped with a maintenance-free battery. You will never have to add water, nor is periodic main- tenance required. Warning! • battery fluid is a corrosive acid solution and can burn or even blind you. Do not allow battery fluid to contact your eyes, skin, or...

  • Page 612

    Caution! (continued) • if a “fast charger” is used while the battery is in the vehicle, disconnect both vehicle battery cables be- fore connecting the charger to the battery. Do not use a “fast charger” to provide starting voltage. Air conditioner maintenance for best possible performance, your air ...

  • Page 613

    Caution! Do not use chemical flushes in your air conditioning system as the chemicals can damage your air condi- tioning components. Such damage is not covered by the new vehicle limited warranty. Refrigerant recovery and recycling r134a — if equipped r-134a air conditioning refrigerant is a hydrofl...

  • Page 614

    Air conditioning filter replacement (a/c air filter) warning! Do not remove the a/c air filter while the vehicle is running, or while the ignition is in the acc or on/run mode. With the a/c air filter removed and the blower operating, the blower can contact hands and may propel dirt and debris into ...

  • Page 615

    5. Open the two air filter access doors. 6. Remove the two particulate air filters from the hvac air inlet housing. Pull the filter elements straight out of the housing, one at a time. Air filter retaining tabs 1 — left retaining tab 2 — right retaining tab air filter access door open 1 — air condit...

  • Page 616

    7. Install the a/c air filter with the air filter position indicators pointing in the same direction as removal. Caution! The a/c air filter is identified with an arrow to indicate airflow direction through the filter. Failure to properly install the filter will result in the need to replace it more...

  • Page 617

    Windshield wiper blades clean the rubber edges of the wiper blades and the windshield periodically with a sponge or soft cloth and a mild nonabrasive cleaner. This will remove accumula- tions of salt or road film. Operation of the wipers on dry glass for long periods may cause deterioration of the w...

  • Page 618

    Wiper blade removal/installation caution! Do not allow the wiper arm to spring back against the glass without the wiper blade in place or the glass may be damaged. 1. Lift the wiper arm to raise the wiper blade off of the glass, until the wiper arm is in the full up position. 2. To disengage the wip...

  • Page 619

    Holding the wiper arm with one hand, slide the wiper blade down towards the base of the wiper arm. 3. With the wiper blade disengaged, remove the wiper blade from the wiper arm. 4. Gently lower the wiper arm onto the glass. Wiper blade with release tab in unlocked position 1 — wiper blade 2 — wiper ...

  • Page 620

    Installing the front wipers 1. Lift the wiper arm off of the glass, until the wiper arm is in the full up position. 2. Position the wiper blade near the hook on the tip of the wiper arm. 3. Insert the hook on the tip of the arm through the opening in the wiper blade. 4. Slide the wiper blade up into...

  • Page 621

    3. To remove the wiper blade from the wiper arm, grasp the wiper blade nearest to wiper arm with your right hand. With your left hand hold the wiper arm as you pull the wiper blade away from the wiper arm past its stop far enough to unsnap the wiper blade pivot pin from the receptacle on the end of ...

  • Page 622

    4. Still grasping the wiper blade, move the wiper blade away from the wiper arm to disengage. Wiper blade removed from wiper arm 1 — wiper arm 2 — wiper blade wiper blade removed from wiper arm 1 — wiper blade 2 — wiper blade pivot pin 3 — wiper arm receptacle 4 — wiper arm 620 maintaining your vehi...

  • Page 623

    Installing the rear wiper 1. Insert the wiper blade pivot pin into the opening on the end of the wiper arm. Grab the bottom end of the wiper arm with one hand, and press the wiper blade flush with the wiper arm until it snaps into place. 2. Install wiper assembly back on the wiper stud at it’s origi...

  • Page 624

    Exhaust system the best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system. If you notice a change in the sound of the exhaust system; or if the exhaust fumes can be detected inside the vehicle; or when the underside or rear of the vehicle i...

  • Page 625

    Caution! • the catalytic converter requires the use of un- leaded fuel only. Leaded gasoline will destroy the effectiveness of the catalyst as an emissions control device and may seriously reduce engine perfor- mance and cause serious damage to the engine. • damage to the catalytic converter can res...

  • Page 626

    To minimize the possibility of catalytic converter damage: • do not shut off the engine or interrupt the ignition, when the transmission is in gear and the vehicle is in motion. • do not try to start the engine by pushing or towing the vehicle. • do not idle the engine with any spark plug wires disc...

  • Page 627

    Check the engine cooling system hoses for brittle rubber, cracking, tears, cuts, and tightness of the connection at the coolant recovery bottle and radiator. Inspect the entire system for leaks. With the engine at normal operating temperature (but not running), check the cooling system pressure cap ...

  • Page 628

    Caution! (continued) organic additive technology (oat) engine cool- ant is different and should not be mixed with hybrid organic additive technology (hoat) en- gine coolant (antifreeze) or any “globally compat- ible” coolant (antifreeze). If a non-oat engine coolant (antifreeze) is introduced into t...

  • Page 629

    That meets the requirements of fca material standard ms.90032. When adding engine coolant (antifreeze): • we recommend using mopar antifreeze/coolant 10 year/150,000 mile formula oat (organic additive technology) that meets the requirements of fca ma- terial standard ms.90032. • mix a minimum soluti...

  • Page 630

    Cooling system pressure cap the cap must be fully tightened to prevent loss of engine coolant (antifreeze), and to ensure that engine coolant (antifreeze) will return to the radiator from the coolant recovery tank. The cap should be inspected and cleaned if there is any accumulation of foreign mater...

  • Page 631

    Engine coolant level the coolant bottle provides a quick visual method for determining that the coolant level is adequate. With the engine idling, and warm to normal operating tempera- ture, the level of the engine coolant (antifreeze) in the bottle should be between the ranges indicated on the bott...

  • Page 632

    • if frequent engine coolant (antifreeze) additions are required, the cooling system should be pressure tested for leaks. • maintain engine coolant (antifreeze) concentration at a minimum of 50% oat coolant (conforming to ms.90032) and distilled water for proper corrosion protection of your engine w...

  • Page 633

    Power disc brakes disc brakes do not require adjustment; however, several hard stops during the break-in period are recommended to seat the linings and wear off any foreign material. Brake master cylinder the fluid level in the master cylinders should be checked whenever the vehicle is serviced. If ...

  • Page 634

    Warning! (continued) cause it to boil unexpectedly during hard or pro- longed braking, resulting in sudden brake failure. This could result in a collision. • overfilling the brake fluid reservoir can result in spilling brake fluid on hot engine parts, causing the brake fluid to catch fire. Brake flu...

  • Page 635

    Special additives the manufacturer strongly recommends against using any special additives in the transmission. Automatic transmission fluid (atf) is an engineered product and its performance may be impaired by supple- mental additives. Therefore, do not add any fluid addi- tives to the transmission...

  • Page 636

    5. Place the shift lever momentarily into each gear posi- tion (allowing time for the transmission to fully en- gage in each position), ending with the transmission in park. 6. Remove the dipstick, wipe it clean and reinsert it until seated. 7. Remove the dipstick again and note the fluid level on b...

  • Page 637

    Caution! If the fluid temperature is below 50°f (10°c) it may not register on the dipstick. Do not add fluid until the temperature is elevated enough to produce an accurate reading. Run the engine at idle, in park, to warm the fluid. 8. Reinstall the engine cover and snap it down securely onto the f...

  • Page 638

    Manual transmission — if equipped selection of lubricant use only manufacturer’s recommended manual trans- mission fluid. Refer to “fluids, lubricants, and genuine parts” in “maintaining your vehicle” for further informa- tion. Fluid level check check the fluid level by removing the fill plug. The f...

  • Page 639

    Transfer case fluid level check the fluid level should be to the bottom edge of the fill hole (a) when the vehicle is in a level position. Adding fluid fluid should be added only at filler hole until fluid begins to run out of the hole. Drain first remove the fill plug (b), then the drain plug (c). ...

  • Page 640

    Front/rear axle fluid for normal service, periodic fluid level checks are not required. When the vehicle is serviced for other reasons the exterior surfaces of the axle assembly should be inspected. If gear oil leakage is suspected inspect the fluid level. Refer to “fluids, lubricants, and genuine p...

  • Page 641

    The following maintenance recommendations will enable you to obtain maximum benefit from the corrosion resistance built into your vehicle. What causes corrosion? Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle. The most common causes are: • road...

  • Page 642

    Caution! • do not use abrasive or strong cleaning materials such as steel wool or scouring powder that will scratch metal and painted surfaces. • use of power washers exceeding 1,200 psi (8 274 kpa) can result in damage or removal of paint and decals. Special care • if you drive on salted or dusty r...

  • Page 643

    Wheel and wheel trim care • all wheels and wheel trim, especially aluminum and chrome plated wheels, should be cleaned regularly with a mild soap and water to prevent corrosion. • to remove heavy soil and/or excessive brake dust, use mopar wheel cleaner. Note: if your vehicle is equipped with dark v...

  • Page 644

    Interior care use mopar total clean to clean fabric upholstery and carpeting. Use mopar total clean to clean vinyl upholstery. Mopar total clean is specifically recommended for leather upholstery. Your leather upholstery can be best preserved by regular cleaning with a damp soft cloth. Small particl...

  • Page 645

    Caution! Do not use alcohol and alcohol-based and/or keton based cleaning products to clean leather seats, as damage to the seat may result. Glass surfaces all glass surfaces should be cleaned on a regular basis with mopar glass cleaner, or any commercial household-type glass cleaner. Never use an a...

  • Page 646

    Replace the belts if they appear frayed or worn or if the buckles do not work properly. Warning! A frayed or torn belt could rip apart in a collision and leave you with no protection. Inspect the belt system periodically, checking for cuts, frays, or loose parts. Damaged parts must be replaced immed...

  • Page 647

    • be especially careful when washing the windows by following the directions for “care of fabric top win- dows.” washing – use mopar car wash or equivalent, or mild soap suds, lukewarm water, and a brush with soft bristles. If extra cleaning is required, use mopar con- vertible cloth top cleaner or ...

  • Page 648

    Caution! (continued) • the front panel(s) must be positioned properly to ensure sealing. Improper installation can cause water to leak into the vehicle’s interior. Care of fabric top windows caution! Your vehicle’s fabric top has pliable plastic windows which can be scratched unless special care is ...

  • Page 649

    Regularly. Use mopar soft top zipper cleaner and lubricant or equivalent to ease zipper operation. Before applying, make sure the zipper teeth are clear of sand, mud, and other materials. Clean both sides of the zipper, not just one side. Rinse both zipper halves with fresh water and allow to dry. A...

  • Page 650

    Warning! (continued) • if a general protection fuse for safety systems (air bag system, braking system), power unit systems (engine system, gearbox system) or steering system blows, contact an authorized dealer. Totally integrated power module the totally integrated power module is located in the en...

  • Page 651

    Cavity cartridge fuse mini fuse description j1 – – – j2 30 amp pink – transfer case module j3 – – – j4 25 amp clear – driver door node j5 25 amp clear – passenger door node j6 40 amp green – anti-lock brake system (abs) pump/stability control system j7 30 amp pink – anti-lock brake system (abs) valv...

  • Page 652

    Cavity cartridge fuse mini fuse description j17 40 amp green – starter solenoid j18 20 amp blue – powertrain control module (pcm) trans range j19 60 amp yellow – radiator fan j20 30 amp pink – front wiper lo/hi j21 20 amp blue – front/rear washer j22 – – spare m1 – 15 amp blue center high-mounted st...

  • Page 653

    Cavity cartridge fuse mini fuse description m9 – 20 amp yellow rear heated seat – if equipped m10 – 15 amp blue ignition off draw – vehicle entertainment system, satellite digital audio receiver (sdars), dvd, hands-free module, radio, antenna, universal garage door opener, vanity lamp m11 – 10 amp r...

  • Page 654

    Cavity cartridge fuse mini fuse description m19 – 25 amp clear auto shut down (asd #1 and #2) m20 – 15 amp blue cabin compartment node interior light, switch bank m21 – 20 amp yellow auto shut down (asd #3) m22 – 10 amp red right horn (hi/low) m23 – 10 amp red left horn (hi/low) m24 – 25 amp clear r...

  • Page 655

    Cavity cartridge fuse mini fuse description m34 – 10 amp red park assist, climate control system, headlamp wash, compass m35 – 10 amp red heated mirrors m36 – 20 amp yellow power outlet m37 – 10 amp red anti-lock brake system, electronic stability control, stop lamp switch, fuel pump relay m38 – 25 ...

  • Page 656

    Vehicle storage if you are leaving your vehicle dormant for more than 21 days, you may want to take steps to protect your battery. You may: • remove cartridge fuse #j13 in the power distribution center (pdc) labeled ignition-off draw (iod) and store it in a safe location within the pdc. • or, discon...

  • Page 657

    Exterior bulbs bulb number headlamps (2) h13 front park/turn signal lamps (2) 3157na front side marker lamps (2) 168 fog lamps psx24w rear stop/tail/turn lamps (2) 3157 center high-mounted stop lamp l.E.D. Backup lamps (2) 3157 license lamp 194 note: numbers refer to commercial bulb types that can b...

  • Page 658

    Bulb replacement note: lens fogging can occur under certain atmo- spheric conditions. This will usually clear as atmospheric conditions change to allow the condensation to change back into a vapor. Turning the lamps on will usually accelerate the clearing process. Headlamp 1. Open hood and support u...

  • Page 659

    Front park/turn signal 1. Remove the front grille. Turn the retainers along the top 1/4 turn counterclockwise and remove. 2. Pull the bottom of the grille away starting at one side and working toward the other. 3. Turn the socket assembly 1/4 turn counterclockwise and remove from housing. Pull the b...

  • Page 660

    Rear tail, stop, turn signal, and backup lamp 1. Remove the two inboard screws attaching the tail light housing to the body. Do not remove the out- board screws at any time. 2. Separate the housing from the body by pushing the lamp inboard while pulling the lamp away from the body. 3. Rotate the app...

  • Page 661

    Fluid capacities u.S. Metric fuel (approximate) two door models 18.6 gallons 70 liters four door models 22.5 gallons 85 liters engine oil with filter 3.6l engine 6 quarts 5.6 liters cooling system * 3.6l engine (mopar antifreeze/ engine coolant 10 year/150,000 mile formula or equivalent) 10.5 quarts...

  • Page 662

    Fluids, lubricants, and genuine parts engine component fluid, lubricant, or genuine part engine coolant we recommend you use mopar antifreeze/coolant 10 year/150,000 mile formula oat (organic additive technology) or equivalent meeting the requirements of fca material standard ms.90032. Engine oil we...

  • Page 663

    Caution! • mixing of engine coolant (antifreeze) other than specified organic additive technology (oat) en- gine coolant (antifreeze), may result in engine damage and may decrease corrosion protection. Organic additive technology (oat) engine cool- ant is different and should not be mixed with hybri...

  • Page 664

    Chassis component fluid, lubricant, or genuine part automatic transmission – if equipped use only atf+4 automatic transmission fluid. Failure to use atf+4 fluid may affect the function or performance of your transmission. We recommend mopar atf+4 fluid. Manual transmission – if equipped we recommend...

  • Page 665: Maintenance Schedules

    Maintenance schedules contents 䡵 maintenance schedule . . . . . . . . . . . . .664 ▫ maintenance chart. . . . . . . . . . . . . . . . . . . . .666 8.

  • Page 666

    Maintenance schedule your vehicle is equipped with an automatic oil change indicator system. The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance. Based on engine operation conditions, the oil change indicator message will illuminate. This...

  • Page 667

    Note: under no circumstances should oil change inter- vals exceed 10,000 miles (16,000 km), twelve months or 350 hours of engine run time, whichever comes first. The 350 hours of engine run or idle time is generally only a concern for fleet customers. Severe duty all models change engine oil at 4,00...

  • Page 668

    Required maintenance intervals refer to the maintenance schedules on the following page for the required maintenance intervals. At every oil change interval as indicated by oil change indicator system: • change oil and filter • rotate the tires. Rotate at the first sign of irregu- lar wear, even if ...

  • Page 669

    Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,000 192,000 208,0...

  • Page 670

    Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,000 192,000 208,0...

  • Page 671

    Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,000 192,000 208,0...

  • Page 672

    Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,000 192,000 208,0...

  • Page 673: Contents

    If you need consumer assistance contents 䡵 suggestions for obtaining service for your vehicle . . . . . . . . . . . . . . . . . . . . . . .673 ▫ prepare for the appointment. . . . . . . . . . . . .673 ▫ prepare a list . . . . . . . . . . . . . . . . . . . . . . . .673 ▫ be reasonable with requests ....

  • Page 674

    䡵 department of transportation uniform tire quality grades . . . . . . . .679 ▫ treadwear. . . . . . . . . . . . . . . . . . . . . . . . . . .679 ▫ traction grades . . . . . . . . . . . . . . . . . . . . . . .679 ▫ temperature grades. . . . . . . . . . . . . . . . . . . .680 672 if you need consumer...

  • Page 675

    Suggestions for obtaining service for your vehicle prepare for the appointment if you are having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty. Discuss additional charges with the service manager....

  • Page 676

    Facilities, factory-trained technicians, special tools, and the latest information to ensure the vehicle is fixed correctly and in a timely manner. This is why you should always talk to an authorized dealer service manager first. Most matters can be re- solved with this process. • if for some reason...

  • Page 677

    In mexico contact av. Prolongacion paseo de la reforma, 1240 sante fe c.P. 05109 mexico, d. F. In mexico city: 5081-7568 outside mexico city: 1-800-505-1300 puerto rico and u.S. Virgin islands customer service chrysler international services llc p.O. Box 191857 san juan 00919-1857 tel.: (787) 782-57...

  • Page 678

    Warranty expires. The manufacturer stands behind only the manufacturer’s service contracts. If you purchased a manufacturer’s service contract, you will receive plan provisions and an owner identification card in the mail within three weeks of the vehicle delivery date. If you have any questions abo...

  • Page 679

    Warranty information see the warranty information booklet, located on the dvd, for the terms and provisions of fca us llc warranties applicable to this vehicle and market. Mopar parts mopar fluids, lubricants, parts, and accessories are available from an authorized dealer. They are recom- mended for...

  • Page 680

    Canada, motor vehicle defect investigations and recalls at 1-800-333-0510 or go to http://www.Tc.Gc.Ca/roadsafety/ publication order forms to order the following manuals, you may use either the website or the phone numbers listed below. Visa, mas- tercard, american express, and discover orders are a...

  • Page 681

    Call toll free at: • 1-800-890-4038 (u.S.) • 1-800-387-1143 (canada) or visit us on the worldwide web at: • www.Techauthority.Com department of transportation uniform tire quality grades the following tire grading categories were established by the national highway traffic safety administration. The...

  • Page 682

    Warning! The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics. Temperature grades the temperature grades are a (the highest), b, and c, representing the tire’s resistan...

  • Page 683: Index

    Index 10

  • Page 684

    About your brakes . . . . . . . . . . . . . . . . . . . . . . . .480 adding engine coolant (antifreeze) . . . . . . . . . . . .626 adding fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . .539 additives, fuel . . . . . . . . . . . . . . . . . . . . . . . . . . .537 air bag . . . . . . . ....

  • Page 685

    Automatic dimming mirror . . . . . . . . . . . . . . . . . .112 automatic door locks . . . . . . . . . . . . . . . . . . . . . .41 automatic headlights . . . . . . . . . . . . . . . . . . . . . .169 automatic oil change indicator . . . . . . . . . . . . . . .353 automatic temperature control (atc) ....

  • Page 686

    Caps, filler fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .539 power steering . . . . . . . . . . . . . . . . . . . . . . . . .477 radiator (coolant pressure) . . . . . . . . . . . . . . . .628 carbon monoxide warning . . . . . . . . . . . . . . .100, 538 cargo light . . . . ...

  • Page 687

    Compact spare tire . . . . . . . . . . . . . . . . . . . . . . . .516 compass. . . . . . . . . . . . . . . . . . . . . . . . .338, 341, 348 compass calibration. . . . . . . . . . . . . . . . . . . .341, 349 compass variance . . . . . . . . . . . . . . . . . . . . .340, 350 computer, trip/travel. . ....

  • Page 688

    Disabled vehicle towing . . . . . . . . . . . . . . . . . . . .589 disarming, security system . . . . . . . . . . . . . . . . . . .21 disposal antifreeze (engine coolant) . . . . . . . . . . . . . . . .628 door locks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38 child-protection door...

  • Page 689

    Compartment identification . . . . . . . . . . . . . . . .595 coolant (antifreeze) . . . . . . . . . . . . . . . . . . . . .660 cooling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .624 exhaust gas caution . . . . . . . . . . . . . . . . .100, 538 fails to start . . . . . . . . . . . . ...

  • Page 690

    Fluid capacities . . . . . . . . . . . . . . . . . . . . . . . . . .659 fluid leaks . . . . . . . . . . . . . . . . . . . . . . . . . . . . .104 fluid level checks . . . . . . . . . . . . . . . . . . . . . . . .638 engine oil . . . . . . . . . . . . . . . . . . . . . . . . . . . .600 manual transmis...

  • Page 691

    Gasoline, clean air . . . . . . . . . . . . . . . . . . . . . . . .535 gasoline (fuel) . . . . . . . . . . . . . . . . . . . . . . . . . . .534 gasoline, reformulated . . . . . . . . . . . . . . . . . . . . .535 gauges fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .324 gear ra...

  • Page 692

    Hood release . . . . . . . . . . . . . . . . . . . . . . . . . . . .167 ignition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 ignition key removal . . . . . . . . . . . . . . . . . . . . . . .14 illumina...

  • Page 693

    Leaks, fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . .104 life of tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . .519 light bulbs . . . . . . . . . . . . . . . . . . . . . . . . . .104, 654 lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .104, 168 air ...

  • Page 694

    Automatic door . . . . . . . . . . . . . . . . . . . . . . . . .41 child protection . . . . . . . . . . . . . . . . . . . . . . . . .42 door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38 power door . . . . . . . . . . . . . . . . . . . . . . . . . . . .40 lubrication, body . . ...

  • Page 695

    Oil change indicator, reset . . . . . . . . . . . . . . . . . .353 oil, engine . . . . . . . . . . . . . . . . . . . . . . . . . .600, 660 capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . .659 change interval . . . . . . . . . . . . . . . . . . . . .353, 600 dipstick . . . . . . . . ...

  • Page 696

    Door locks . . . . . . . . . . . . . . . . . . . . . . . . . . . .40 inverter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .189 mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .113 steering . . . . . . . . . . . . . . . . . . . . . . . . . . .476, 477 windows . . . . ....

  • Page 697

    Replacement keys . . . . . . . . . . . . . . . . . . . . . . . . .17 replacement parts. . . . . . . . . . . . . . . . . . . . . . . . .598 replacement tires . . . . . . . . . . . . . . . . . . . . . . . . .519 reporting safety defects . . . . . . . . . . . . . . . . . . . .677 resetting oil change i...

  • Page 698

    Front seat . . . . . . . . . . . . . . . . . . . . . . . .49, 51, 54 inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . .101 operating instructions . . . . . . . . . . . . . . . . . . . .54 pregnant women . . . . . . . . . . . . . . . . . . . . . . . .59 pretensioners . . . . . . . . ....

  • Page 699

    Side window demisters (defrosters) . . . . . . . . . . . .427 signals, turn. . . . . . . . . . . . . . . . . . .104, 170, 657, 658 snow chains (tire chains) . . . . . . . . . . . . . . . . . . .521 snow tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .514 soft top. . . . . . . . . . ...

  • Page 700

    Sway control, trailer. . . . . . . . . . . . . . . . . . . . . . .496 swing gate, rear . . . . . . . . . . . . . . . . . . . . . . . . . .46 synthetic engine oil . . . . . . . . . . . . . . . . . . . . . . .602 system, remote starting . . . . . . . . . . . . . . . . . . . . .28 temperature control, ...

  • Page 701

    Towing . . . . . . . . . . . . . . . . . . . . . . . . . .544, 548, 589 24-hour towing assistance . . . . . . . . . . . . . . . .129 disabled vehicle . . . . . . . . . . . . . . . . . . . . . . . .589 recreational . . . . . . . . . . . . . . . . . . . . . . . . . . .563 weight . . . . . . . . . . . ...

  • Page 702

    Uconnect advanced phone connectivity . . . . . . . . . . . . . .133 phone call features . . . . . . . . . . . . . . . . . . . . .125 phone features . . . . . . . . . . . . . . . . . . . . . . . . .128 uconnect 130 operating instructions auxiliary mode . . . . . . . .366 operating instructions radio ...

  • Page 703

    Window fogging . . . . . . . . . . . . . . . . . . . . . . . . .426 windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43 power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43 windshield defroster . . . . . . . . . . . . .102, 417, 423, 424 windshield, folding ....

  • Page 704

    Installation of radio transmitting equipment special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained person- nel. The following must be obs...

  • Page 705

    First edition printed in u.S.A. Stick with the specialists ® 16mk74-126-aa ©2015 fca us llc. All rights reserved. Jeep is a registered trademark of fca us llc..