1. DL manuals
  2. Jeep
  3. Automobile
  4. COMMANDER 2010
  5. Owner's Manual

Jeep COMMANDER 2010 Owner's Manual

Other manuals for COMMANDER 2010: User Manual

Summary of COMMANDER 2010

  • Page 1

    Table of contents section page 1 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 things to know before starting your vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 3 understanding the featu...

  • Page 3: Introduction

    Introduction contents 䡵 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 䡵 rollover warning . . . . . . . . . . . . . . . . . . . . . . . 5 䡵 how to use this manual . . . . . . . . . . . . . . . . . . 6 䡵 warnings and cautions . . . . . . . . . . . . . . . . . . . 8 䡵 vehicle ide...

  • Page 4

    Introduction congratulations on selecting your new chrysler group llc vehicle. Be assured that it represents precision workmanship, distinctive styling, and high quality - all essentials that are traditional to our vehicles. This is a specialized utility vehicle designed for both on-road and off-roa...

  • Page 5

    This owner’s manual has been prepared with the assis- tance of service and engineering specialists to acquaint you with the operation and maintenance of your vehicle. It is supplemented by a warranty information booklet, located on the dvd, and various customer-oriented documents. Please take the ti...

  • Page 6

    Failure to use driver and passenger seat belts provided is a major cause of severe or fatal injury. In fact, the u.S. Government notes that the universal use of existing seat belts could cut the highway death toll by 10,000 or more each year and could reduce disabling injuries by two million annuall...

  • Page 7

    1 introduction 7.

  • Page 8

    Warnings and cautions this owner’s manual contains warnings against op- erating procedures that could result in an accident or bodily injury. It also contains cautions against proce- dures that could result in damage to your vehicle. If you do not read this entire manual, you may miss important info...

  • Page 9

    Vehicle modifications/alterations warning! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death. 1 introduction 9.

  • Page 11: Contents

    Things to know before starting your vehicle contents 䡵 a word about your keys . . . . . . . . . . . . . . . . . 14 ▫ wireless ignition node (win) . . . . . . . . . . . . 14 ▫ integrated ignition key . . . . . . . . . . . . . . . . . 15 ▫ ignition key removal . . . . . . . . . . . . . . . . . . 15 ▫ ...

  • Page 12

    ▫ remote open window feature — if equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 ▫ using the panic alarm . . . . . . . . . . . . . . . . . 24 ▫ programming additional transmitters . . . . . . 24 ▫ transmitter battery service . . . . . . . . . . . . . . 24 ▫ general information . ....

  • Page 13

    ▫ enhanced seat belt use reminder system (beltalert 威 ) . . . . . . . . . . . . . . . . . . . . . . . . . 47 ▫ seat belts and pregnant women . . . . . . . . . . 48 ▫ seat belt extender . . . . . . . . . . . . . . . . . . . . . 48 ▫ supplemental restraint systems (srs) . . . . . . 49 ▫ advanced front...

  • Page 14

    A word about your keys your vehicle uses a keyless ignition system. This system consists of a remote keyless entry (rke) transmitter with integrated ignition key and a wireless ignition node (win) with integral ignition switch. You can insert the double-sided key into the ignition switch with either...

  • Page 15

    Integrated ignition key the integrated ignition key operates the ignition switch. It also contains the remote keyless entry (rke) trans- mitter and an emergency key, which stores in the rear of the rke transmitter. The emergency key allows for entry into the vehicle should the battery in the vehicle...

  • Page 16

    Note: • if you try to remove the key before you place the shift lever in park, it may become trapped temporarily in the ignition switch. If this occurs, rotate the key to the right slightly, then remove the key as described. If a malfunction occurs, the system will trap the key in the ignition switc...

  • Page 17

    Key-in-ignition reminder if you open the driver’s door with the integrated ignition key in the ignition, a chime will sound to remind you to remove the key. Note: the key-in-ignition reminder only sounds when the integrated ignition key is placed in the lock or acc position. Sentry key 姞 the sentry ...

  • Page 18

    Note: the sentry key 威 immobilizer system is not compatible with aftermarket remote starting systems. Use of these systems may result in vehicle starting problems and loss of security protection. All of the rke transmitters provided with your new vehicle have been programmed to the vehicle electroni...

  • Page 19

    General information the sentry key 威 system complies with fcc rules part 15 and with rss-210 of industry canada. Operation is subject to the following conditions: • this device may not cause harmful interference. • this device must accept any interference that may be received, including interference...

  • Page 20

    Vehicle security light (located in the instrument cluster) will flash rapidly for about 16 seconds to signal that the vehicle security alarm is arming. During this 16 second arming period, opening any door or the liftgate will cancel the arming. If the vehicle security alarm success- fully arms, the...

  • Page 21

    Remote keyless entry (rke) this system allows you to lock or unlock the doors and liftgate, or activate the panic alarm, from distances up to approximately 66 ft (20 m) using a hand-held remote keyless entry (rke) transmitter. The rke transmitter does not need to be pointed at the vehicle to activat...

  • Page 22

    Remote key unlock, driver door/all doors first press this feature lets you program the system to unlock either the driver’s door or all doors, on the first press of the unlock button on the rke transmitter. To change the current setting, proceed as follows: • for vehicles equipped with the electroni...

  • Page 23

    To lock the doors press and release the lock button on the rke transmit- ter to lock all doors. The turn signal lamps will flash and the horn will chirp to acknowledge the signal. Sound horn with remote key lock this feature will cause the horn to chirp when the doors are locked with the rke transmi...

  • Page 24

    Using the panic alarm to turn the panic alarm feature on or off, press and hold the panic button on the rke transmitter for at least one second and release. When the panic alarm is on, the headlights and park lamps will flash, the horn will pulse on and off, and the interior lights will turn on. The...

  • Page 25

    2. Remove and replace the battery. Avoid touching the new battery with your fingers. Skin oils may cause battery deterioration. If you touch a battery, clean it with rubbing alcohol. 3. Reposition the access door panel over the battery opening and snap into place. General information this device com...

  • Page 26

    If your rke transmitter fails to operate from a normal distance, check for these two conditions: 1. A weak battery in the rke transmitter. The expected life of the battery is a minimum of three years. 2. Closeness to a radio transmitter such as a radio station tower, airport transmitter, and some mo...

  • Page 27

    Warning! • do not start or run an engine in a closed garage or confined area. Exhaust gas contains carbon mon- oxide (co) which is odorless and colorless. Car- bon monoxide is poisonous and can cause serious injury or death when inhaled. • keep remote keyless entry (rke) transmitters away from child...

  • Page 28

    Note: to avoid unintentional shutdowns, the system will disable the one time press of the remote start button for two seconds after receiving a valid remote start request. To exit remote start mode and drive the vehicle before the end of 15 minute cycle, press and release the unlock button on the rk...

  • Page 29

    Power door locks the power door lock switch is located on each front door panel. Press the switch to lock or unlock the doors. If the plunger is down when the door is closed, the door will lock. Therefore, make sure the key is not inside the vehicle before closing the door. If you press the door loc...

  • Page 30

    This feature is selectable and can be turned on or off. Refer to “auto door locks” under “customer- programmable features” in the “electronic vehicle infor- mation center (evic),” in section 4 of this manual, or see your authorized dealer. Child protection door lock the rear doors of your vehicle ar...

  • Page 31

    Passenger/rear passenger door windows. The window controls will operate only when the ignition switch is in the on or acc position. The power window switches remain active for up to 10 minutes after the ignition switch has been turned off. Opening a vehicle front door will cancel this feature. Auto-...

  • Page 32

    Auto up feature with anti-pinch protection — driver’s and front passenger door only lift the window switch to the second detent, release, and the window will go up automatically. To stop the window from going all the way up during the auto up operation, push down on the switch briefly. To close the ...

  • Page 33

    Wind buffeting wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions. This is a normal occur- rence and ...

  • Page 34

    Warning! Driving with the liftgate open can allow poisonous exhaust gases into your vehicle. You and your pas- sengers could be injured by these fumes. Keep the liftgate closed when you are operating the vehicle. Liftgate flipper glass the liftgate flipper glass is also unlocked when the liftgate is...

  • Page 35

    Warning! To avoid injury, stand back when opening. Glass will automatically rise. Once the liftgate flipper glass has been opened, connec- tion to the rear window wiper is interrupted, preventing activation of the rear wiper blade while the flipper glass is open. Warning! Driving with the flipper gl...

  • Page 36

    When the liftgate button on the rke transmitter is pressed two times, the turn signals will flash twice to signal that the liftgate is opening or closing. Note: • in the event of a power malfunction to the liftgate, an emergency liftgate latch release can be used to open the liftgate. The emergency ...

  • Page 37

    • the power liftgate must be in the full open position for rear liftgate close button or overhead console close button to operate. If the liftgate is not fully open, press the liftgate button on the fob with integrated key (fobik) to fully open the liftgate, and then press it again to close. • if th...

  • Page 38

    Warning! • driving with the liftgate open can allow poison- ous exhaust gases into your vehicle. You and your passengers could be injured by these fumes. Keep the liftgate closed when you are operating the vehicle. • if you are required to drive with the liftgate open, make sure that all windows are...

  • Page 39

    • knee bolsters/blockers for front seat occupants • front seat belts incorporate pretensioners to enhance occupant protection by managing occupant energy during an impact event if you will be carrying children too small for adult-sized seat belts, the seat belts or the lower anchors and tether for c...

  • Page 40

    Research has shown that seat belts save lives, and they can reduce the seriousness of injuries in a collision. Some of the worst injuries happen when people are thrown from the vehicle. Seat belts reduce the possibility of ejection and the risk of injury caused by striking the inside of the vehicle....

  • Page 41

    Lap/shoulder belt operating instructions 1. Enter the vehicle and close the door. Sit back and adjust the seat. 2. The seat belt latch plate is above the back of your seat. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to make the belt go aroun...

  • Page 42

    3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” warning! • a belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your bel...

  • Page 43

    Warning! (continued) • a belt that is worn under your arm is very danger- ous. Your body could strike the inside surfaces of the vehicle in a collision, increasing head and neck injury. A belt worn under the arm can cause internal injuries. Ribs are not as strong as shoulder bones. Wear the belt ove...

  • Page 44

    6. To release the belt, push the red button marked press on the buckle. The belt will automatically retract to its stowed position. If necessary, slide the latch plate down the webbing to allow it to retract fully. Warning! A frayed or torn belt could rip apart in a collision and leave you with no p...

  • Page 45

    As a guide, if you are shorter than average, you will prefer a lower position, and if you are taller than average, you will prefer a higher position. When you release the anchorage, try to move it up or down to make sure that it is locked in position. Automatic locking mode — if equipped in this mod...

  • Page 46

    How to disengage the automatic locking mode disconnect the combination lap/shoulder belt and allow it to retract completely to disengage the automatic locking mode and activate the vehicle sensitive (emer- gency) locking mode. Energy management feature this vehicle has a safety belt system with an e...

  • Page 47

    Note: these devices are not a substitute for proper seat belt placement by the occupant. The seat belt must still be worn snugly and positioned properly. The pretensioners are triggered by the occupant re- straint controller (orc). Like the airbags, the pretension- ers are single use items. After a ...

  • Page 48

    4. Turn the ignition key to the off position. A single chime will sound to signify that you have successfully completed the programming. Beltalert 威 can be reactivated by repeating this procedure. Note: although beltalert 威 has been deactivated, the seat belt reminder light will continue to illumina...

  • Page 49

    Supplemental restraint systems (srs) this vehicle has airbags for both the driver and front passenger as a supplement to the seat belt restraint systems. The driver’s front airbag is mounted in the center of the steering wheel. The passenger’s front airbag is mounted in the instrument panel, above t...

  • Page 50

    The advanced front airbags have a multistage inflator design. This allows the airbag to have different rates of inflation based on the severity and type of collision. This vehicle may also be equipped with supplemental side airbag inflatable curtains (sabic) to protect the driver, front, and rear pa...

  • Page 51

    Low, medium, or high. If a low output is sufficient to meet the need, the remaining gas in the inflator is expended. Warning! • do not put anything on or around the airbag covers or attempt to open them manually. You may damage the airbags and you could be injured because the airbags may no longer b...

  • Page 52

    Note: • should a vehicle rollover occur, the pretensioners and/or sabic airbags on both sides of the vehicle may deploy. • airbag covers may not be obvious in the interior trim; but they will open during airbag deployment. The system includes sensors adjacent to both front and rear seat occupants th...

  • Page 53

    Along with seat belts and pretensioners, advanced front airbags work with the knee bolsters to provide improved protection for the driver and front passenger. Side airbags also work with seat belts to improve occupant protection. Knee impact bolsters the knee impact bolsters help protect the knees o...

  • Page 54

    You should read the instructions provided with your child restraint to make sure that you are using it properly. All occupants should always wear their lap and shoul- der belts properly. The driver and front passenger seats should be moved back as far as practical to allow the advanced front airbags...

  • Page 55

    Airbag deployment sensors and controls occupant restraint controller (orc) the orc is part of a federally regulated safety system required for this vehicle. The orc determines if deployment of the front and/or side airbags in a frontal or side collision is required. Based on the impact sensors signa...

  • Page 56

    The orc monitors the readiness of the electronic parts of the system whenever the ignition switch is in the start or on position. If the key is in the lock position, in the acc position, or not in the ignition, the airbags are not on and will not inflate. The orc contains a backup power supply syste...

  • Page 57

    The advanced front airbags. Different airbag inflation rates are possible, based on the collision type and sever- ity. The steering wheel hub trim cover and the upper right side of the instrument panel separate and fold out of the way as the bags inflate to their full size. The bags fully inflate in...

  • Page 58

    Front and side impact sensors in front and side impacts, impact sensors aid the orc in determining appropriate response to impact events. Ad- ditional sensors in the orc determine the level of airbag deployment and provide verification. Enhanced accident response system in the event of an impact cau...

  • Page 59

    If you do have a collision which deploys the airbags, any or all of the following may occur: • the nylon airbag material may sometimes cause abra- sions and/or skin reddening to the driver and front passenger as the airbags deploy and unfold. The abrasions are similar to friction rope burns or those...

  • Page 60

    Maintaining your airbag system warning! • modifications to any part of the airbag system could cause it to fail when you need it. You could be injured if the airbag system is not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the stee...

  • Page 61

    Airbag warning light you will want to have the airbags ready to inflate for your protection in a collision. While the airbag system is designed to be mainte- nance free, if any of the following occurs, have an authorized dealer service the system immediately. • the airbag warning light does not come...

  • Page 62

    2. Under certain circumstances, edr data may not be recorded (e.G., loss of battery power). In conjunction with other data gathered during a com- plete accident investigation, the electronic data may be used by chrysler group llc and others to learn more about the possible causes of crashes and asso...

  • Page 63

    4. Otherwise required by law. Data parameters that are recorded: • diagnostic trouble code(s) and warning light status for electronically-controlled safety systems, including the airbag system • vehicle speed • engine rpm • brake switch status • pedal position • and other parameters depending on veh...

  • Page 64

    Warning! In a collision, an unrestrained child, even a tiny baby, can become a projectile inside the vehicle. The force required to hold even an infant on your lap can become so great that you could not hold the child, no matter how strong you are. The child and others could be badly injured. Any ch...

  • Page 65

    Warning! (continued) • improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the manufacturer’s directions ex- actly when installing an infant or child restraint. • a rearward-facing infant re...

  • Page 66

    Locking retractor, pull the belt from the retractor until there is enough to allow you to pass through the child restraint and slide the latch plate into the buckle. Then, pull the belt until it is fully extracted from the retrac- tor. Allow the belt to return to the retractor, pulling on the excess...

  • Page 67

    Older children and child restraints children who weigh more than 20 lbs (9 kg) and who are older than one year can ride forward-facing in the vehicle. Forward-facing child seats and convertible child seats used in the forward-facing direction are for children who weigh 20 to 40 lbs (9 to 18 kg), and...

  • Page 68

    Latch — child seat anchorage system (lower anchors and tether for children) your vehicle’s second row seat is equipped with the child restraint anchorage system called latch. The latch system provides for the installation of the child restraint without using the vehicle’s seat belts, instead securin...

  • Page 69

    If your child seats are not latch-compatible, you can only install the child seats using the vehicle’s seat belts. For typical installation instructions, refer to “installing the latch-compatible child restraint system”. Installing the latch-compatible child restraint system we urge you to carefully...

  • Page 70

    Many, but not all restraint systems will be equipped with separate straps on each side, with each having a hook or connector for attachment to the lower anchorage and a means of adjusting the tension in the strap. Forward- facing toddler restraints and some rear-facing infant restraints will also be...

  • Page 71

    Warning! Improper installation of a child restraint to the latch anchorages can lead to failure of an infant or child restraint. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint. Installing child restraints using th...

  • Page 72

    The buckle, turn the buckle around, and insert the latch plate into the buckle again. If you still can’t make the child restraint secure, try a different seating position. To attach a child restraint tether strap: route the tether strap over the seatback and attach the hook to the tether anchor loca...

  • Page 73

    Engine break-in recommendations a long break-in period is not required for the engine in your vehicle. Drive moderately during the first 300 miles (500 km). After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable. While cruising, brief full-throttle acceleration ...

  • Page 74

    Warning! (continued) • do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • be sure everyone in your vehicle is in a seat and using a seat belt properly. Exhaust gas warning! Exhaust gases can injure or kill. They contain carbon monoxide (co), whi...

  • Page 75

    Whenever a change is noticed in the sound of the exhaust system, when exhaust fumes can be detected inside the vehicle, or when the underside or rear of the vehicle is damaged, have a competent mechanic inspect the com- plete exhaust system and adjacent body areas for broken, damaged, deteriorated, ...

  • Page 76

    Defroster check operation by selecting the defrost mode and place the blower control on high speed. You should be able to feel the air directed against the windshield. See your authorized dealer for service if your defroster is inoperable. Periodic safety checks you should make outside the vehicle t...

  • Page 77: Contents

    Understanding the features of your vehicle contents 䡵 mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82 ▫ inside day/night mirror . . . . . . . . . . . . . . . . 82 ▫ automatic dimming mirror — if equipped . . . 82 ▫ outside mirrors . . . . . . . . . . . . . . . . . . . . . . 83...

  • Page 78

    ▫ four-way passenger’s power seat — if equipped . . . . . . . . . . . . . . . . . . . . . . . 88 ▫ head restraints . . . . . . . . . . . . . . . . . . . . . . 89 ▫ front heated seats — if equipped . . . . . . . . . 90 ▫ rear heated seats — if equipped . . . . . . . . . . 91 ▫ 40/20/40 second row fol...

  • Page 79

    ▫ battery saver feature — exterior/interior lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110 ▫ lights-on reminder . . . . . . . . . . . . . . . . . . 110 ▫ turn signals . . . . . . . . . . . . . . . . . . . . . . . . 110 ▫ lane change assist . . . . . . . . . . . . . . . . . . . . ...

  • Page 80

    䡵 rear park assist — if equipped . . . . . . . . . . . 122 ▫ rear park assist sensors . . . . . . . . . . . . . . . 122 ▫ rear park assist warning display . . . . . . . . 123 ▫ enable/disable the rear park assist . . . . . . 124 ▫ service the rear park assist . . . . . . . . . . . . 125 ▫ cleaning t...

  • Page 81

    ▫ venting sunroof — express . . . . . . . . . . . . . 138 ▫ sunshade operation . . . . . . . . . . . . . . . . . . 139 ▫ wind buffeting . . . . . . . . . . . . . . . . . . . . . . 139 ▫ sunroof maintenance . . . . . . . . . . . . . . . . . 139 ▫ ignition off operation . . . . . . . . . . . . . . . ....

  • Page 82

    Mirrors inside day/night mirror a two-point pivot system allows for horizontal and vertical adjustment of the mirror. The mirror should be adjusted to center on the view through the rear window. Headlight glare from vehicles behind you can be reduced by moving the small control under the mirror to t...

  • Page 83

    Caution! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror. Apply the solution onto a clean cloth and wipe the mirror clean. Outside mirrors to receive maximum benefit, adjust the outside mirrors to center on the adjacent lane of traffic with a...

  • Page 84

    Outside automatic dimming mirrors — if equipped the driver and passenger outside mirrors will automati- cally adjust for glare from vehicles behind you. This feature is controlled by the inside automatic dimming mirror and can be turned on or off by pressing the button at the base of the inside mirr...

  • Page 85

    Illuminated vanity mirrors — if equipped to access an illuminated vanity mirror, flip down one of the sun visors. Lift the cover to reveal the mirror. The light will turn on automatically. Sun visor extension — if equipped this feature has a pull out extension on the sun visor for increased coverage...

  • Page 86

    Warning! • do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. In a collision, people riding in these areas are more likely to be seriously injured or killed. • be sure everyone in your vehicle is in a seat and using a seat belt properly. Front man...

  • Page 87

    Warning! Do not ride with the seatback reclined so that the seat belt is no longer resting against your chest. In a collision you could slide under the seat belt and be seriously or even fatally injured. Use the recliner only when the vehicle is parked. Manual lumbar support adjustment the manual lu...

  • Page 88

    Eight–way driver’s power seat the driver’s power seat switches are located on the outboard side of the driver’s seat. The bottom switch controls up/down, forward/rearward, and tilt adjust- ment. The top switch controls the seatback recline adjust- ment. Warning! Adjusting a seat while the vehicle is...

  • Page 89

    Note: the four-way seat does not have an up/down adjustment. Warning! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust any seat only while the vehi...

  • Page 90

    Warning! Driving a vehicle with the head restraints removed or improperly adjusted could cause serious injury or death in the event of a collision. The head restraints should always be checked prior to operating the vehicle and never adjusted while the vehicle is in motion. Always adjust the head re...

  • Page 91

    Warning! • persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, ex- haustion or other physical condition must exercise care when using the seat heater. It may cause burns even at low temperatures, especially ...

  • Page 92

    After turning the ignition on, you can choose from high, low or off heat settings. Amber indicator lights in each switch indicate the level of heat in use. Two indicator lights will illuminate for high, one for low and none for off. Press the switch once to select high-level heat- ing. Press the swi...

  • Page 93

    Warning! (continued) • do not place anything on the seat that insulates against heat, such as a blanket or cushion. This may cause the seat heater to overheat. To avoid heated seat surfaces coming in contact and poten- tial seat overheating, always ensure that the seat heater is in the off position ...

  • Page 94

    2. Fold the seatback down, and tumble the seat forward. Warning! Do not drive the vehicle with the outer second row seats in the tumbled position. The outer second row seats are only intended to be tumbled for entry and exit to the third row seat. Failure to follow these instructions could result in...

  • Page 95

    Folding middle seatback (second row seat) 1. Pull the release strap. Release strap release strap 3 understanding the features of your vehicle 95.

  • Page 96

    2. Lower the center seatback. Center seat armrest (second row seat) — if equipped the second row center seat may be equipped with a armrest. Pull strap to lower armrest. Folding center seatback armrest (second row seat) 96 understanding the features of your vehicle.

  • Page 97

    50/50 third row folding seat — if equipped to lower rear seat either side of the third row seat can be lowered to allow for extended cargo space and still maintain some rear seating room. 1. Open the tailgate. 2. Pull the seatback release handle (toward rear of ve- hicle) and lower the seatback usin...

  • Page 98

    To raise rear seat 1. Open the tailgate. 2. Detach pull strap from back of seat and pull seatback upward until it locks into place. Reattach strap. 3. Close the tailgate. Warning! The cargo area in the rear of the vehicle (with the rear seatbacks in the locked-up or folded down position) should not ...

  • Page 99

    Your vehicle is equipped with two rke transmitters. One or both rke transmitters can be linked to either memory position. The memory system can accommodate up to four rke transmitters, each one linked to either of the two memory positions. Setting memory positions and linking remote keyless entry tr...

  • Page 100

    5. Turn on the radio and set the radio station presets (up to 12 am and 12 fm stations can be set). 6. Turn the ignition switch to the lock position and remove the key. 7. Press and release the s (set) button located on the driver’s door. 8. Within five seconds, press and release memory button 1 or ...

  • Page 101

    To recall the memory setting for driver two, press memory button number 2 on the driver’s door, or the unlock button on the rke transmitter linked to memory position 2. A recall can be cancelled by pressing any of the memory buttons on the drivers door during a recall (s, 1, or 2). When a recall is ...

  • Page 102

    Easy entry/exit seat this feature provides automatic driver’s seat positioning which will enhance driver mobility out of and into the vehicle. There are two possible easy entry/exit adjustments available: • the seat cushion will move rearward approximately 2.5 in (60 mm), if the starting position of...

  • Page 103

    To open and close the hood to open the hood, two latches must be released. 1. Pull the release lever inside your vehicle located below the instrument panel and in front of the driver’s door. 2. Reach under the hood, move safety latch to the left and lift the hood. Caution! To prevent possible damage...

  • Page 104

    Warning! If the hood is not fully latched, it could fly up when the vehicle is moving and block your forward vision. Be sure all hood latches are fully latched before driving. Lights multifunction lever the multifunction lever controls the operation of the headlights, turn signals, headlight beam se...

  • Page 105

    Headlights and parking lights turn the end of the multifunction lever to the first detent for parking light operation. Turn to the second detent for headlight operation. Turn to the third detent for auto- matic headlight operation (if equipped). Automatic headlight system — if equipped turn the end ...

  • Page 106

    This system performs two functions. With the engine running and the multifunction lever in the auto posi- tion, the headlights will turn on and off based on the surrounding light levels. Headlights on automatically with wipers if your vehicle is equipped with automatic headlights it also has this cu...

  • Page 107

    Note: if the windshield or smartbeam™ mirror is replaced, the smartbeam™ mirror must be re-aimed to ensure proper performance. See your local authorized dealer. To activate 1. Select “auto high beams” refer to “electronic vehicle information center (evic) — customer-programmable features” in section...

  • Page 108

    Daytime running lights — if equipped the high beam headlights come on at a low intensity level whenever the engine is running, and the transmis- sion is not in the park position. The lights remain on until the ignition switch is turned off or the parking brake is engaged. The headlight switch must b...

  • Page 109

    • a front fog light is a lighting device providing illumi- nation forward of the vehicle under conditions of fog, rain, snow or dust. The front fog lights supplement the low beams of a standard headlight system. • proper aim and adjustments of the front fog lights should be made to prevent excessive...

  • Page 110

    Battery saver feature — exterior/interior lights if the multifunction lever is left in the interior light position, parking light position, or the headlight position when the ignition switch is moved to the off position, the battery saver feature will automatically turn off the exterior and interior...

  • Page 111

    Lane change assist tap the lever up or down once, without moving beyond the detent, and the turn signal (right or left) will flash three times then automatically turn off. High/low beam switch push the multifunction lever away from you to switch the headlights to high beam. Pull the lever toward you...

  • Page 112

    By pressing the front recessed area of the lens. To turn these lights off, press the recessed area of the lens a second time. Windshield wipers and washers the windshield wiper/washer control lever is located on the right side of the steering column. The front wipers are operated by rotating a switc...

  • Page 113

    Windshield wiper operation rotate the end of the lever upward to the lo position for low-speed wiper operation. Rotate the end of the lever upward to the hi position for high-speed wiper operation. Caution! Always remove any buildup of snow that prevents the windshield wiper blades from returning to...

  • Page 114

    Warning! Sudden loss of visibility through the windshield could lead to an accident. You might not see other vehicles or other obstacles. To avoid sudden icing of the windshield during freezing weather, warm the windshield with the defroster before and during windshield washer use. Mist use the mist...

  • Page 115

    Delay interval. The delay can be regulated from a maxi- mum of approximately 18 seconds between cycles, to a cycle every 1/2 second. Note: the wiper delay times depend on vehicle speed. If the vehicle is moving less than 10 mph (16 km/h), delay times will be doubled. Rain sensing wipers — if equippe...

  • Page 116

    • the rain sensing feature may not function properly when ice, or dried salt water is present on the wind- shield. • use of rain-x 威 or products containing wax or silicone may reduce rain sensing performance. • a customer programmable feature in the electronic vehicle information center (evic) allow...

  • Page 117

    Tilt/telescoping steering column this feature allows you to tilt the steering column upward or downward. It also allows you to lengthen or shorten the steering column. The tilt/telescoping control handle is located below the steering wheel at the end of the steering column. To unlock the steering co...

  • Page 118

    Improved position with the steering wheel. The adjust- able pedal system is designed to allow a greater range of driver comfort for steering wheel tilt and seat position. The position of the brake and accelerator pedals can be adjusted without compromising safety or comfort in actuating the pedals. ...

  • Page 119

    Caution! Do not place any article under the adjustable pedal’s or impede its ability to move as it may cause damage to the pedal controls. Pedal travel may become lim- ited if movement is stopped by an obstruction in the adjustable pedal’s path. Warning! Do not adjust the pedals while the vehicle is...

  • Page 120

    Note: in order to ensure proper operation, the elec- tronic speed control system has been designed to shut down if multiple speed control functions are operated simultaneously. If this occurs, the electronic speed con- trol system can be reactivated by pushing the electronic speed control on/off but...

  • Page 121

    To deactivate a soft tap on the brake pedal, pulling the electronic speed control lever toward you, or normal brake pres- sure while slowing the vehicle will deactivate electronic speed control without erasing the set speed memory. Pressing the on/off button or turning off the ignition switch erases...

  • Page 122

    Note: • the electronic speed control system maintains speed up and down hills. A slight speed change on moderate hills is normal. • on steep hills a greater speed loss or gain may occur so it may be preferable to drive without electronic speed control. Rear park assist — if equipped the rear park as...

  • Page 123

    Rear park assist warning display the rear park assist warning display, located in the headliner near the flipper glass, provides both visible and audible warnings to indicate the distance between the rear fascia and the detected obstacle. When the ignition is turned to the on position, the warning d...

  • Page 124

    Warning display distances display led obstacle distance from: led color audible signal rear corners rear center 1st led 59 in (150 cm) yellow yes, half second 2nd led 51 in (130 cm) yellow none 3rd led 45 in (115 cm) yellow none 4th led 31.5 in (80 cm) 39 in (100 cm) yellow none 5th led 25.5 in (65 ...

  • Page 125

    When the switch is pressed to disable the system, the instrument cluster will display the “park assist dis- abled” message. Refer to “electronic vehicle informa- tion center (evic)” in section 4 of this manual. When the shift lever is changed to reverse and the system is disabled, the instrument clu...

  • Page 126

    • when you turn off the rear park assist system, the instrument cluster will display “park assist dis- abled.” furthermore, once you turn off the rear park assist system, it remains off until you turn it on again, even if you cycle the ignition key. • when you move the shift lever to the reverse pos...

  • Page 127

    Caution! • the rear park assist system is only a parking aid and it is unable to recognize every obstacle, in- cluding small obstacles. Parking curbs might be temporarily detected or not detected at all. Ob- stacles located above or below the sensors will not be detected when they are in close proxi...

  • Page 128

    Warning! (continued) • before using the rear park assist system, it is strongly recommended that the ball mount and hitch ball assembly is disconnected from the ve- hicle when the vehicle is not used for towing. Failure to do so can result in injury or damage to vehicles or obstacles because the hit...

  • Page 129

    Caution! • to avoid vehicle damage, the rear camera system should only be used as a parking aid. The rear camera system is unable to view every obstacle or object in your drive path. • to avoid vehicle damage, the vehicle must be driven slowly when using the rear camera system to be able to stop in ...

  • Page 130

    Turning the rear camera on or off — without navigation radio 1. Press the ⬙ menu ⬙ hard key. 2. Select ⬙ system setup ⬙ soft key. 3. Enable or disable the rear camera feature by selecting ⬙ enable rear camera in reverse ⬙ soft key. 4. When the vehicle is shifted into reverse, an image of the rear of...

  • Page 131

    Note: homelink 威 is disabled when the vehicle secu- rity alarm is active. Warning! • your motorized door or gate will open and close while you are training the universal transceiver. Do not train the transceiver if people or pets are in the path of the door or gate. Only use this trans- ceiver with ...

  • Page 132

    Programming homelink 姞 before you begin if you have not trained any of the homelink 威 buttons, erase all channels before you begin training. To do this, press and hold the two outside buttons for up to 20 seconds. The evic will display “clearing channels.” release the buttons when the evic mes- sage...

  • Page 133

    Note: some gate operators and garage door openers may require you to replace step 3 with procedures noted in the “gate operator/canadian programming” section. 4. Press and hold the just-trained homelink 威 button. If the channel has been trained, the evic display will now state “channel # transmit.” ...

  • Page 134

    6. Firmly press and release the “learn” or “train- ing” button. The name and color of the button may vary by manufacturer. Note: there are 30 seconds in which to initiate the next step after the “learn” button has been pressed. 7. Return to the vehicle and press the programmed homelink 威 button twic...

  • Page 135

    If you unplugged the device for training, plug it back in at this time. Then proceed with step 4 under “programming homelink 威 ” earlier in this section. Using homelink 姞 to operate, simply press and release the programmed homelink 威 button. Activation will now occur for the trained device (i.E., ga...

  • Page 136

    Troubleshooting tips if you are having trouble programming homelink 威 , here are some of the most common solutions: • replace the battery in the original transmitter. • press the learn button on the garage door opener to complete the training for rolling code. • did you unplug the device for trainin...

  • Page 137

    Power sunroof — if equipped the power sunroof switch is located on the overhead console. Warning! • never leave children in a vehicle with the key in the ignition switch. Occupants, particularly unat- tended children, can become entrapped by the power sunroof while operating the power sunroof switch...

  • Page 138

    Opening sunroof — express press the switch rearward and release, and the sunroof will open automatically from any position. The sunroof will open fully, then stop automatically. This is called “express open”. During express open operation, any movement of the sunroof switch will stop the sunroof. Cl...

  • Page 139

    Sunshade operation the sunshade can be opened manually. However, the sunshade will open automatically as the sunroof opens. Note: the sunshade cannot be closed if the sunroof is open. Wind buffeting wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound ...

  • Page 140

    Note: hold onto shade handle until shade is com- pletely open or closed. Electrical power outlets your vehicle is equipped with 12 volt power outlets that can be used to power cellular phones, small electronics and other low powered electrical accessories. The power outlets are labeled with either a...

  • Page 141

    • to ensure proper operation a mopar 威 knob and element must be used. The front power outlets are located to the left and right of the convenience tray (lower center of instrument panel). Pull lightly on the tab of the plastic cover to access these power outlets. The power outlet located on the left...

  • Page 142

    Warning! To avoid serious injury or death: • do not insert any objects into the receptacles. • do not touch with wet hands. • close the lid when not in use and while driving the vehicle. • if this outlet is mishandled, it may cause an electric shock and failure. Caution! • many accessories that can ...

  • Page 143

    Power inverter — if equipped there is a 115 volt, 150 watt inverter outlet located on the back of the center console to convert dc current to ac current. This outlet can power cellular phones, electron- ics and other low power devices requiring power up to 150 watts. Certain high-end video games, su...

  • Page 144

    May have to be reset manually. To reset the inverter manually press the power inverter button off and on. To avoid overloading the circuit, check the power ratings on electrical devices prior to using the inverter. Press the power inverter switch (located on the upper switch bank) to turn the power ...

  • Page 145

    Warning! To avoid serious injury or death: • do not use a three-prong adaptor. • do not insert any objects into the receptacles. • do not touch with wet hands. • close the lid when not in use. • if this outlet is mishandled it may cause an electric shock and failure. Cupholders front cupholders ther...

  • Page 146

    Cupholders — second row seat the second row seat has two cupholders in the center armrest. Lower the center armrest. Refer to “seats” in this section. Press the front of the cupholder, and the cup- holder will come out of the armrest. Cupholders — third row seat the third row seat passengers have cu...

  • Page 147

    Cargo area features cargo load floor the panel in the load floor is reversible for added utility. One side is carpeted and the other side features a plastic lined tray which holds a variety of items. The cargo load floor is held by spring loaded latches. In order to use the cargo load floor, use the...

  • Page 148

    1. Flip up pull loop(s) so they are perpendicular (straight up) to the top surface of the tray. 2. Pull up on loop(s) and twist 90 degrees, so they are parallel to the slotted hole in tray. 3. Lift tray over loop(s), and reposition tray. 4. Pull up on loop(s) and twist 90 degrees, so they are perpen...

  • Page 149

    Rotate the switch upward to the “on” position to activate the rear wiper. Note: the rear wiper operates in an intermittent mode only. Rotate the switch upward to the “washer” position to activate that rear washer. The washer pump will continue to operate as long as the lever or ring is engaged. Upon...

  • Page 150

    Rear window defroster the rear window defroster button is located on the climate control panel. Press this button to turn on the rear window defroster and the heated outside mirrors (if equipped). An indicator in the button will illuminate when the rear window defroster is on. The rear window defros...

  • Page 151

    Note: if not equipped with crossbars, your authorized dealer can order and install mopar 威 crossbars built specifically for this roof rack system. Distribute cargo weight evenly on the roof rack crossbars. The roof rack does not increase the total load carrying capacity of the vehicle. Be sure the t...

  • Page 152

    The optional crossbars must also be secured in one of the five detent positions marked with an arrow on the siderails to prevent movement. To move the crossbars, loosen the thumb screws located at the upper edge of each crossbar approximately eight turns, then move the crossbar to the desired positi...

  • Page 153

    Caution! (continued) • to avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity of 150 lbs (68 kg). Always distribute heavy loads as evenly as possible and secure the load appropri- ately. • long loads which extend over the windshield, such as wood panels or su...

  • Page 155: Contents

    Understanding your instrument panel contents 䡵 instrument panel features . . . . . . . . . . . . . . . 158 䡵 instrument cluster . . . . . . . . . . . . . . . . . . . . 159 䡵 instrument cluster description . . . . . . . . . . . . 160 䡵 electronic vehicle information center (evic) . . 170 ▫ electronic...

  • Page 156

    䡵 sales code res — am/fm stereo radio with cd player (mp3 aux jack) . . . . . . . . . . . . . . . 189 ▫ operating instructions — radio mode . . . . . 189 ▫ operation instructions — cd mode for cd and mp3 audio play . . . . . . . . . . . . . . . . . 192 ▫ notes on playing mp3 files . . . . . . . . . ...

  • Page 157

    ▫ selecting uconnect™ studios (satellite) mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 216 ▫ satellite antenna . . . . . . . . . . . . . . . . . . . . . 216 ▫ reception quality . . . . . . . . . . . . . . . . . . . . 216 ▫ operating instructions - uconnect™ studios (satellite) mode...

  • Page 158

    Instrument panel features 1 — air outlet 5 — upper switch bank 9 — lower switch bank 2 — instrument cluster 6 — power outlet/cigar lighter 10 — climate controls 3 — radio 7 — storage bin 11 — ignition switch 4 — glove compartment 8 — power outlet 12 — storage bin 158 understanding your instrument pa...

  • Page 159

    Instrument cluster 4 understanding your instrument panel 159.

  • Page 160

    Instrument cluster description 1. Speedometer indicates vehicle speed. 2. Brake warning light this light monitors various brake functions, including brake fluid level and parking brake application. If the brake light turns on, it may indicate that the parking brake is applied, that the brake fluid l...

  • Page 161

    Warning! Driving a vehicle with the red brake light on is dangerous. Part of the brake system may have failed. It will take longer to stop the vehicle. You could have an accident. Have the vehicle checked immediately. Vehicles equipped with the anti-lock brake system (abs), are also equipped with el...

  • Page 162

    5. Malfunction indicator light (mil) the malfunction indicator light (mil) is part of an onboard diagnostic system called obd ii that monitors engine and automatic transmission con- trol systems. The light will illuminate when the key is in the on position before engine start. If the bulb does not c...

  • Page 163

    6. Airbag warning light this light turns on and remains on for six to eight seconds as a bulb check when the ignition switch is first turned on. If the light is not on during starting, stays on, or turns on while driving, have the system inspected by an authorized dealer as soon as possible. 7. Anti...

  • Page 164

    10. Oil pressure warning light this light indicates low engine oil pressure. The light should turn on momentarily when the engine is started. If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible. A chime will sound for four minutes when this light turns o...

  • Page 165

    Reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability. Please note that the tpms is not a substitute for proper tire maintenance, and it is the driver’s responsibility to maintain correct tire pressure, even if under-inflation has not reached the lev...

  • Page 166

    Caution! The tpms has been optimized for the original equipment tires and wheels. Tpms pressures and warning have been established for the tire size equipped on your vehicle. Undesirable system opera- tion or sensor damage may result when using re- placement equipment that is not of the same size, t...

  • Page 167

    Warning! A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant. You may want to call an authorized dealer- ship for service if your vehicle overheats. If you decide to look under the hood yourself, see section 7 of this manual. Follow the warnings ...

  • Page 168

    17. 4wd low mode indicator — if equipped this light alerts the driver that the vehicle is in the 4wd low mode. The front and rear driveshafts are mechanically locked together forcing the front and rear wheels to rotate at the same speed. 18. Seat belt reminder light when the ignition switch is first...

  • Page 169

    21. Shift lever indicator the shift lever indicator is self-contained within the instrument cluster. It displays the gear position of the automatic transmission. Note: you must apply the brakes before shifting from park. 22. Fuel gauge the pointer shows the level of fuel in the fuel tank when the ig...

  • Page 170

    Electrical devices or increase engine speed (if at idle). If the charging system light remains on, it means that the vehicle is experiencing a problem with the charging system. Obtain service immediately. See an autho- rized dealer. If jump starting is required, refer to “jump starting procedures” i...

  • Page 171

    • vehicle information warning message displays • personal settings (customer-programmable features) • compass display • outside temperature display • trip computer functions the system allows the driver to select information by pressing the following buttons mounted on the steering wheel: menu butto...

  • Page 172

    Electronic vehicle information center (evic) displays when the appropriate conditions exist, the evic displays the following messages: • turn signal on • perform service • damaged key — key does not communi- cate • key not programmed — key not pro- grammed • wrong key — key does not belong to vehicl...

  • Page 173

    • hood/glass/doors open (with graphic) • hood/gate/door open (with graphic) • hood/gate/doors open (with graphic) • liftglass/door open (with graphic) • liftglass/doors open (with graphic) • liftglass/hood open (with graphic) • washer fluid low (with graphic) • coolant low (with graphic) • oil chang...

  • Page 174

    • memory #1 positions set • memory #2 positions set • memory system disabled — seatbelt buck- led (with graphic) • memory system disabled — vehicle not in park • driver 1 memory • driver 2 memory • adj. Pedals disabled — cruise control set • adj. Pedals disabled — shifter in reverse • low tire press...

  • Page 175

    • manual close to operate (power liftgate models only) • vehicle not in park • ignition position • press brake to start • insert key • turn to on • eco – fuel saver indicator engine oil change indicator system oil change required your vehicle is equipped with an engine oil change indicator system. T...

  • Page 176

    Trip functions press and release the menu button until one of the following trip functions displays in the evic: • average fuel economy/fuel saver mode (5.7l engine only) • distance to empty • trip a • trip b • elapsed time • service distance • display units of measure in press the scroll button to ...

  • Page 177

    This feature allows you to monitor when you are driving in a fuel efficient manner, and it can be used to modify driving habits in order to increase fuel economy. Distance to empty (dte) shows the estimated distance that can be traveled with the fuel remaining in the tank. This estimated distance is...

  • Page 178

    And average fuel economy, according to the current fuel tank level. Dte cannot be reset through the function select button. Note: significant changes in driving style or vehicle loading will greatly affect the actual drivable distance of the vehicle, regardless of the dte displayed value. When the d...

  • Page 179

    The function select button for two seconds. Current display will reset along with other functions compass display the compass readings indicate the direction the vehicle is facing. Press and release the compass/temperature button to display one of eight compass readings and the outside temperature. ...

  • Page 180

    5. Complete one or more 360–degree turns (in an area free from large metal or metallic objects) until the “cal” indicator turns off. The compass will now function normally. Compass variance compass variance is the difference between magnetic north and geographic north. To compensate for the differen...

  • Page 181

    4. Press and release the function select button to change the variance number. Continue until desired number is reached. 5. Press either menu, scroll, or compass/temp button to set the value and exit. Personal settings (customer-programmable features) personal settings allows the driver to set and r...

  • Page 182

    Opened. To make your selection, press and release the function select button until yes (y) or no (n) appears. Remote key unlock when “driver door 1st press” is selected, only the driver’s door will unlock on the first press of the remote keyless entry (rke) transmitter unlock button. When “driver do...

  • Page 183

    Auto high beams (available with smartbeam™ only) when this feature is selected, the high beam headlights will deactivate automatically under certain conditions. To make your selection, press and release the function select button until yes (y) or no (n) appears. Refer to “lights/smartbeam™ — if equi...

  • Page 184

    Note: the seat will return to the memorized seat location (if recall memory with remote key unlock is set to on) when the rke transmitter is used to unlock the door. Refer to “easy entry/exit seat” under “driver memory seat” in section 3 of this manual for more information. Key off power delay when ...

  • Page 185

    Display eco — if equipped the “eco” message is located in the compass/ temperature display, this message can be turned on or off. To make your selection, press and release the func- tion select button until “on” or “off” appears. System status press and release the menu button until one of the follo...

  • Page 186

    • your system can be set to display pressure units in psi, kpa, or bar. Sales code (rer/ren) — am/fm/cd/dvd radio – if equipped note: the sales code is located on the lower right side of the unit’s faceplate. The ren and rer radios contain a cd/dvd player, usb port, and a 30-gigabyte hard drive (hdd...

  • Page 187

    To manually set the clock — rer/ren 1. Turn on the radio. 2. Touch the screen where the time is displayed. 3. Touch the screen where “user clock” is displayed. The clock setting menu will appear on the screen. 4. To move the hour forward, touch the screen where the word “hour” with the arrow pointin...

  • Page 188

    Show time if radio is off when selected, this feature will display the time of day on the touch screen when the radio is turned off. Proceed as follows to change the current setting: 1. Turn on the radio. 2. Touch the screen where the time is displayed. The clock setting menu will appear on the scre...

  • Page 189

    Sales code res — am/fm stereo radio with cd player (mp3 aux jack) note: the radio sales code is located on the lower right side of the radio faceplate. Operating instructions — radio mode note: the ignition switch must be in the on or acc position to operate the radio. Power switch/volume control (r...

  • Page 190

    To seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection. Holding either button will bypass stations without stopping, until you release it. Time button press the time button to alternate display of the time and radio frequency. Clo...

  • Page 191

    Push the rotary tune/scroll control knob a second time and mid will display. Turn the tune/scroll control knob to the right or left to increase or decrease the mid-range tones. Push the rotary tune/scroll control knob a third time and treble will display. Turn the tune/scroll control knob to the rig...

  • Page 192

    You may add a second station to each pushbutton by repeating the above procedure with this exception: press the set/rnd button twice and set 2 will show in the display window. Each button can be set for set 1 and set 2 in both am and fm. This allows a total of 12 am and 12 fm stations to be stored i...

  • Page 193

    If you insert a disc with the ignition on and the radio on, the unit will switch from radio to cd mode and begin to play when you insert the disc. The display will show the track number, and index time in minutes and seconds. Play will begin at the start of track 1. Caution! • this cd player will ac...

  • Page 194

    Time button press this button to change the display from a large cd playing time display to a small cd playing time display. Rw/ff press and hold the ff (fast forward) button and the cd player will begin to fast forward until ff is released, or rw or another cd button is pressed. The rw (reverse) bu...

  • Page 195

    The radio uses the following limits for file systems: • maximum number of folder levels: 8 • maximum number of files: 255 • maximum number of folders. (the radio display of file names and folder names is limited. For large numbers of files and/or folders, the radio may be unable to display the file ...

  • Page 196

    Rates (vbr) are also supported. The majority of mp3 files use a 44.1 khz sampling rate and a 192, 160, 128, 96 or vbr bit rate. Mpeg specifi- cation sampling fre- quency (khz) bit rate (kbps) mpeg-1 audio layer 3 48, 44.1, 32 320, 256, 224, 192, 160, 128, 112, 96, 80, 64, 56, 48, 40, 32 mpeg-2 audio...

  • Page 197

    Operation instructions - auxiliary mode the auxiliary (aux) jack is an audio input jack, which allows the user to plug in a portable device, such as an mp3 player, or cassette player, and utilize the vehicle’s audio system to amplify the source and play through the vehicle speakers. Pressing the dis...

  • Page 198

    Operating instructions — radio mode note: the ignition switch must be in the on or acc position to operate the radio. Power switch/volume control (rotary) push the on/volume control knob to turn on the radio. Push the on/volume control knob a second time to turn off the radio. Electronic volume cont...

  • Page 199

    Phone button uconnect™ phone — if equipped press this button to operate the uconnect™ phone feature (if equipped). Refer to “uconnect™ phone” in the uconnect™ user manual located on the dvd for further details. If your vehicle is not equipped with or this feature is not available on your vehicle, a ...

  • Page 200

    Info button press the info button for an rds station (one with call letters displayed). The radio will return a radio text message broadcast from an fm station (fm mode only). Rw/ff pressing the rw (rewind) or ff (fast forward) buttons causes the tuner to search for the next frequency in the directi...

  • Page 201

    Push the rotary tune/scroll control knob again to exit setting tone, balance, and fade. Music type button pressing this button once will turn on the music type mode for five seconds. Pressing the music type button or turning the tune/scroll control knob within five seconds will allow the program for...

  • Page 202

    Program type 16-digit character display soft soft soft rock soft rck soft rhythm and blues soft r&b sports sports talk talk top 40 top 40 weather weather by pressing the seek button when the music type icon is displayed, the radio will be tuned to the next frequency station with the same selected mu...

  • Page 203

    Window. Select the button (1–6) you wish to lock onto this station and press and release that button. If a button is not selected within five seconds after pressing the set/ rnd button, the station will continue to play but will not be stored into pushbutton memory. You may add a second station to e...

  • Page 204

    Inserting compact disc(s) gently insert one cd into the cd player with the cd label facing up. The cd will automatically be pulled into the cd player and the cd icon will illuminate on the radio display. If a cd does not go into the slot more than 1.0 in (2.5 cm), a disc may already be loaded and mu...

  • Page 205

    Note: ejecting with the ignition off is not allowed on convertible or soft-top models (if equipped). Seek button press the right seek button for the next selection on the cd. Press the left seek button to return to the beginning of the current selection, or return to the beginning of the previous se...

  • Page 206

    Supported media (disc types) the mp3 file recording media supported by the radio are cdda, cd-r, cd-rw, mp3, and cdda+mp3. Supported medium formats (file systems) the medium formats supported by the radio are iso 9660 level 1 and level 2 and includes the joliet extension. When reading discs recorded...

  • Page 207

    Supported mp3 file formats the radio will recognize only files with the *.Mp3 exten- sion as mp3 files. Non-mp3 files named with the *.Mp3 extension may cause playback problems. The radio is designed to recognize the file as an invalid mp3 and will not play the file. When using the mp3 encoder to co...

  • Page 208

    Loading times for playback of mp3 files may be affected by the following: • media - cd-rw media may take longer to load than cd-r media • medium formats - multisession discs may take longer to load than non-multisession discs • number of files and folders - loading times will increase with more file...

  • Page 209

    Operation instructions - auxiliary mode the auxiliary (aux) jack is an audio input jack which allows the user to plug in a portable device such as an mp3 player or cassette player and utilize the vehicle’s audio system to amplify the source and play through the vehicle speakers. Pressing the aux but...

  • Page 210

    This feature allows you to plug an ipod 威 into the vehicle’s sound system through a 16–pin connector, using the provided interface cable. Uci supports mini, 4g, photo, nano, 5g ipod 威 and iphone 威 devices. Some ipod 威 software versions may not fully support the uci features. Please visit apple’s web...

  • Page 211

    Using this feature by using the provided connection cable to connect an ipod 威 to the vehicle’s uci 16–pin connector port: • the ipod 威 audio can be played on the vehicle’s sound system, providing metadata (artist, track title, album, etc.) information on the radio display. • the ipod 威 can be contr...

  • Page 212

    • jump backward in the current track by pressing and holding the rw button. Holding the rw button long enough will take you to the beginning of the current track. • jump forward in the current track by pressing and holding the ff >> button. • a single press backward rw or forward ff >> will jump bac...

  • Page 213

    • rnd button (available on sales code res radio only): pressing this button toggles between shuffle on and shuffle off modes for the ipod 威 . If the rnd icon is showing on the radio display, then the shuffle mode is on. List or browse mode during play mode, pressing any of the buttons described belo...

  • Page 214

    • pressing a preset button will display the current list on the top line and the first item in that list on the second line. • to exit list mode without selecting a track, press the same preset button again to go back to play mode . • list button: the list button will display the top level menu of t...

  • Page 215

    Uconnect™ studios (satellite radio) — if equipped (ren/rer/res radios only) satellite radio uses direct satellite-to-receiver broadcast- ing technology to provide clear digital sound, coast to coast. The subscription service provider is sirius satellite radio. This service offers over 130 channels o...

  • Page 216

    Sirius id number will display. The sirius id number display will time out in two minutes. Press any button on the radio to exit this screen. Esn/sid access with ren/rer radios while in sat mode, press the menu button on the radio faceplate. Next, touch the subscription tab on the touch screen. All t...

  • Page 217

    Operating instructions - uconnect™ studios (satellite) mode note: the ignition switch must be in the on or acc position to operate the radio. Seek buttons press and release the seek buttons to search for the next channel in satellite mode. Press the right switch to seek up and the left switch to see...

  • Page 218

    Or turning the tune/scroll control knob within five seconds will allow the program format type to be se- lected. Toggle the music type button again to select the music type. By pressing the seek button when the music type function is active, the radio will be tuned to the next channel with the same ...

  • Page 219

    Pushbutton memory. The channels stored in set 2 memory can be selected by pressing the pushbutton twice. Every time a preset button is used, a corresponding button number will display. Buttons 1 - 6 these buttons tune the radio to the channels that you commit to pushbutton memory (12 satellite stati...

  • Page 220

    The lcd screen is located on the headliner behind the front seats. Remote sound system controls — if equipped the remote sound system controls are located on the rear surface of the steering wheel. Reach behind the wheel to access the switches. Lowering the display screen remote control location 220...

  • Page 221

    The right-hand control is a rocker-type switch with a pushbutton in the center and controls the volume and mode of the sound system. Pressing the top of the rocker switch will increase the volume, and pressing the bottom of the rocker switch will decrease the volume. Pressing the center button will ...

  • Page 222

    Cd player pressing the top of the switch once will go to the next track on the cd. Pressing the bottom of the switch once will go to the beginning of the current track, or to the beginning of the previous track if it is within one second after the current track begins to play. If you press the switc...

  • Page 223

    6. Do not expose the disc to direct sunlight. 7. Do not store the disc where temperatures may become too high. Note: if you experience difficulty in playing a particu- lar disc, it may be damaged (i.E., scratched, reflective coating removed, a hair, moisture or dew on the disc) oversized, or have pr...

  • Page 224

    The instrument panel features four dual-vane airflow registers. Two registers are located on the outer ends of the instrument panel and two are located in the center of the instrument panel. These registers can be closed to partially block airflow, and they can be adjusted to direct airflow where th...

  • Page 225

    Directed to the front door windows through the side window demister grilles. Some airflow is delivered to the floor while in defrost so that comfort can be maintained. Defrost/floor air flows through the front and rear floor outlets and the outlets at the base of the windshield. Air is also directed...

  • Page 226

    Recirculation the recirculation feature can be selected with the mode control knob. You may choose be- tween bi-level recirculation and panel recir- culation air outlets while in this mode. Nor- mally, air enters from outside the vehicle. However, when in recirculation mode air inside the vehicle is...

  • Page 227

    Note: the numbers on the temperature dial represent a comfort setting when the mode knob is set to auto, and not the actual air temperature. Turn the mode control (on the right) knob to auto, and place the blower control (on the left) to either lo auto or hi auto. The lo auto position should be used...

  • Page 228

    Note: the temperature setting can be adjusted at any time without affecting automatic control operation. How- ever, if the driver and/or passenger temperature knobs are set to the full hot or full cold positions, the air temperature out of the ducts will be full hot or full cold respectively. With t...

  • Page 229

    • to provide you with maximum comfort in the auto- matic mode, during cold start-ups the blower fan will remain off until the engine warms up. However, the fan will engage immediately if the defrost mode is selected or if you manually select a blower speed. • under certain conditions (after the vehi...

  • Page 230

    230 understanding your instrument panel.

  • Page 231

    Note: regardless of the type of operation, when a temperature knob is set to the full clockwise or full counterclockwise position, the system will deliver full hot or full cold air out of the ducts, respectively. The operator can override the auto mode setting and select the direction of the air by ...

  • Page 232

    Bi-level air flows both through the outlets located in the instrument panel and those located on the floor. Air flows through the registers in the back of the center console, and under the front seats to the rear seat passengers. These registers can be closed to block airflow. The center console out...

  • Page 233

    Recirculation mode to be selected while in the defrost or defrost/floor modes. Attempting to use recirculation while in these modes will cause the led in the button to blink and then turn off. Rear climate control — if equipped the manual rear climate control system has one floor air outlet (passeng...

  • Page 234

    Note: the rear climate control system cannot be con- trolled from the front seat; it can only be turned on and off. All control of the rear system must be performed by the rear occupants. Rear blower control the left knob on the rear control panel has four posi- tions, “off”, and a range of three bl...

  • Page 235

    Rear temperature control the center knob on the rear control panel allows the third row seat occupants to have control of the rear temperature as follows: • when the temperature knob is in the cold (blue) position, cold air will be delivered from the outlets. As the temperature knob is turned toward...

  • Page 236

    Regular cleaning of the inside of the windows with a non-filming cleaning solution (vinegar and water works very well) will help prevent contaminates (cigarette smoke, perfumes, etc.) from sticking to the windows. Contaminates increase the rate of window fogging. Summer operation air conditioned veh...

  • Page 237

    Operating tips chart 4 understanding your instrument panel 237.

  • Page 239: Starting And Operating

    Starting and operating contents 䡵 starting procedure . . . . . . . . . . . . . . . . . . . . . 243 ▫ normal starting . . . . . . . . . . . . . . . . . . . . . 243 ▫ extreme cold weather (below ⫺ 20°f or ⫺ 29°c) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 244 ▫ if engine fails to start . ...

  • Page 240

    ▫ quadra-trac ii 威 operating instructions/ precautions — if equipped . . . . . . . . . . . . . 256 ▫ shift positions . . . . . . . . . . . . . . . . . . . . . . 257 ▫ shifting procedures . . . . . . . . . . . . . . . . . . . 258 ▫ quadra-drive 威 ii system — if equipped . . . . 260 䡵 on-road driving ...

  • Page 241

    ▫ hill start assist (hsa) – four-wheel drive models with nv245 two–speed transfer case only . . . . . . . . . . . . . . . . . . . . . . . . . 280 ▫ hill descent control (hdc) – four-wheel drive models with nv245 two–speed transfer case only . . . . . . . . . . . . . . . . . . . 283 ▫ esp/bas warning...

  • Page 242

    ▫ 3.7 engine . . . . . . . . . . . . . . . . . . . . . . . . . 314 ▫ 5.7l engine . . . . . . . . . . . . . . . . . . . . . . . . 314 ▫ reformulated gasoline . . . . . . . . . . . . . . . . 315 ▫ gasoline/oxygenate blends . . . . . . . . . . . . . 315 ▫ e-85 usage in non-flex fuel vehicles . . . . . ...

  • Page 243

    Starting procedure before starting your vehicle, adjust your seat, adjust the inside and outside mirrors, fasten your seat belt, and if present, instruct all other occupants to buckle their seat belts. Warning! • never leave children alone in a vehicle. Leaving unattended children in a vehicle is da...

  • Page 244

    Extreme cold weather (below ⫺ 20°f or ⫺ 29°c) to ensure reliable starting at these temperatures, use of an externally powered electric engine block heater (avail- able from your authorized dealer) is recommended. If engine fails to start warning! • never pour fuel or other flammable liquids into the...

  • Page 245

    Release it as soon as the starter engages. The starter motor will disengage automatically in 10 seconds. Once this occurs, release the accelerator pedal, turn the ignition switch to the lock position, wait 10 to 15 seconds, then repeat the “normal starting” procedure. Caution! To prevent damage to t...

  • Page 246

    Automatic transmission caution! Damage to the transmission may occur if the follow- ing precautions are not observed: • shift into park only after the vehicle has come to a complete stop. • shift into or out of reverse only after the vehicle has come to a complete stop and the engine is at idle spee...

  • Page 247

    Brake/transmission shift interlock system this vehicle is equipped with a brake transmission shift interlock system (btsi) that holds the shift lever in the park position when the ignition switch is in the lock position. To move the shift lever out of the park position, the ignition switch must be t...

  • Page 248

    6. Move the shift lever into the neutral position. 7. The vehicle may then be started in neutral. Have your vehicle inspected by your local authorized dealer, if the shift lock manual override has been used. Five–speed automatic transmission the electronically controlled transmission provides a prec...

  • Page 249

    Never use park while the vehicle is in motion. Apply the parking brake when leaving the vehicle in this range. Always apply the parking brake first, then place the shift lever into the park position. Warning! • never use the park position as a substitute for the parking brake. Always apply parking b...

  • Page 250

    Electronic range select (ers)operation the electronic range select (ers) shift control allows you to move the shift lever left (-) or right (+) when the shift lever is in the drive position, allowing you to limit the highest available gear. For example, if the driver shifts the transmission into ers...

  • Page 251

    Downshift). For example, if you are in drive and are in 3rd (direct) gear, when you tap the shift lever one time to the left (-), the display will show 4 (ers 4 is direct gear). Another tap to the left (-) will shift the transmission down to ers 3 (the added underdrive gear). When in the drive posit...

  • Page 252

    • transmission has reached normal operating temperature. Note: if the vehicle is started in extremely cold tem- peratures, the transmission may not shift into overdrive and will automatically select the most desirable gear for operation at this temperature. Normal operation will resume when the tran...

  • Page 253

    Performance and reduce the potential for transmission overheating or failure due to excessive shifting. When operating in “tow/haul” mode, the transmission will shift into direct gear and overdrive will be enabled under steady cruise conditions. The “tow/haul indicator light” will illuminate in the ...

  • Page 254

    3. Turn the engine off, and be sure to turn the key to the lock position. 4. Wait approximately 10 seconds, then restart the en- gine. 5. Move the shift lever to the desired gear range. If the problem is no longer detected, the transmission will return to normal operation. If the problem persists, p...

  • Page 255

    The transmission may not shift into the top overdrive gear (normal 5th gear) until the transmission fluid and engine coolant are warm. • if the vehicle has not been driven in several days, the first few seconds of operation after shifting the trans- mission into gear may seem sluggish. This is due t...

  • Page 256

    Four-wheel drive operation quadra-trac i 姞 operating instructions/ precautions — if equipped the quadra-trac i 威 is a single-speed (hi range only) transfer case, which provides convenient full-time four– wheel drive. No driver interaction is required. The brake traction control (btc) system, which c...

  • Page 257

    Proper operation of four-wheel drive vehicles depends on tires of equal size, type, and circumference on each wheel. Any difference will adversely affect shifting and cause damage to the transfer case. Because four-wheel drive provides improved traction, there is a tendency to exceed safe turning an...

  • Page 258

    Additional traction and maximum pulling power for loose, slippery road surfaces only. Do not exceed 25 mph (40 km/h). Shifting procedures 4wd hi to 4wd low with the vehicle at speeds of 0 to 3 mph (0 to 5 km/h), key on or engine running, shift the transmission into neutral, and raise the transfer ca...

  • Page 259

    “4wd low” indicator light in the instrument cluster will flash and go out when the shift is complete. Release the t-handle. Note: • if shift conditions/interlocks are not met, or a transfer case motor temperature protection condition exists, a “check shift procedures” message will flash from the ele...

  • Page 260

    5. Repeat steps 1 to 4 to shift out of neutral. Note: if shift conditions/interlocks are not met, a “check shift procedures” message will flash from the electronic vehicle information center (evic). Refer to “electronic vehicle information center (evic)” in section 4 of this manual. Quadra-drive 姞 i...

  • Page 261

    On-road driving tips utility vehicles have higher ground clearance and a narrower track to make them capable of performing in a wide variety of off-road applications. Specific design characteristics give them a higher center of gravity than ordinary cars. An advantage of the higher ground clearance ...

  • Page 262

    Caution! When driving through water, do not exceed 5 mph (8 km/h). Always check water depth before entering, as a precaution, and check all fluids afterward. Driv- ing through water may cause damage that may not be covered by the new vehicle limited warranty. Driving through water more than a few in...

  • Page 263

    Driving in snow, mud and sand in heavy snow, when pulling a load, or for additional control at slower speeds, shift the transmission to a low gear and shift the transfer case to 4wd low if necessary. Refer to “four-wheel drive operation” in this section. Do not shift to a lower gear than necessary t...

  • Page 264

    If the wheels start to slip as you approach the crest of a hill, ease off the accelerator and maintain forward motion by turning the front wheels slowly. This may provide a fresh “bite” into the surface and will usually provide traction to complete the climb. Traction downhill shift the transmission...

  • Page 265

    • after extended operation in mud, sand, water, or similar dirty conditions, have brake rotors, wheels, brake linings, and axle yokes inspected and cleaned as soon as possible. Warning! Abrasive material in any part of the brakes may cause excessive wear or unpredictable braking. You might not have ...

  • Page 266

    Warning! Continued operation with reduced power steering assist could pose a safety risk to yourself and others. Service should be obtained as soon as possible. Caution! Prolonged operation of the steering system at the end of the steering wheel travel will increase the steering fluid temperature an...

  • Page 267

    Apparent, and/or the system is not functioning as antici- pated. Coordinate inspection efforts through an autho- rized dealer. Warning! Fluid level should be checked on a level surface and with the engine off to prevent injury from moving parts and to ensure accurate fluid level reading. Do not over...

  • Page 268

    Be sure the parking brake is firmly set when parked and the shift lever is in the park position. When parking on a hill, you should apply the parking brake before placing the shift lever in park, otherwise the load on the transmission locking mechanism may make it difficult to move the shift lever o...

  • Page 269

    When parking on a hill, turn the front wheels toward the curb on a downhill grade, and away from the curb on an uphill grade. The parking brake should always be applied whenever the driver is not in the vehicle. Anti-lock brake system the anti-lock brake system (abs) is designed to aid the driver in...

  • Page 270

    Warning! • pumping of the anti-lock brakes will diminish their effectiveness and may lead to an accident. Pumping makes the stopping distance longer. Just press firmly on your brake pedal when you need to slow down or stop. • the abs cannot prevent the natural laws of phys- ics from acting on the ve...

  • Page 271

    • do not “ride” the brakes by resting your foot on the pedal. This could overheat the brakes and result in unpredictable braking action, longer stopping dis- tances, or brake damage. • when descending mountains or hills, repeated brak- ing can cause brake fade with loss of braking control. Avoid rep...

  • Page 272

    Electronic brake control system your vehicle is equipped with an advanced electronic brake control system that includes the anti-lock brake system (abs), traction control system (tcs), brake assist system (bas), electronic roll mitigation (erm), and electronic stability program (esp). All five of th...

  • Page 273

    Traction control system (tcs) this system monitors the amount of wheel spin of each of the driven wheels. If wheel spin is detected, brake pressure is applied to the slipping wheel(s) and engine power is reduced to provide enhanced acceleration and stability. A feature of the tcs system functions si...

  • Page 274

    Warning! The bas cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions. The bas cannot prevent accidents, including those re- sulting from excessive speed in turns, driving on very slippery surfaces, or hydropla...

  • Page 275

    Warning! Many factors, such as vehicle loading, road condi- tions and driving conditions, influence the chance that wheel lift or rollover may occur. Erm cannot prevent all wheel lift or rollovers, especially those that involve leaving the roadway or striking objects or other vehicles. Only a safe, ...

  • Page 276

    “esp/tcs indicator light” begins to flash during accel- eration, ease up on the accelerator and apply as little throttle as possible. Be sure to adapt your speed and driving to the prevailing road conditions. Warning! The electronic stability program (esp) cannot pre- vent the natural laws of physic...

  • Page 277

    Partial off this mode is entered by momentarily pressing the “esp off” switch. When in “partial off” mode, the tcs portion of esp, except for the “limited slip” feature described in the tcs section, has been disabled and the “esp/tcs indicator light” will be illuminated. All other stability features...

  • Page 278

    Mode is overcome, turn esp back on by momentarily pressing the “esp off” switch. This may be done while the vehicle is in motion. Full off (four-wheel drive models only) this mode is intended for off-highway or off-road use when esp stability features could inhibit vehicle maneu- verability due to t...

  • Page 279

    Warning! With the esp switched off, the enhanced vehicle stability offered by esp and erm are unavailable. In an emergency evasive maneuver, the esp and erm systems will not engage to assist in maintaining stability. The “full off” esp mode is intended for off-road use only. 4wd low range full off t...

  • Page 280

    Warning! With the esp switched off, the enhanced vehicle stability offered by esp and erm are unavailable. In an emergency evasive maneuver, the esp and erm systems will not engage to assist in maintaining stability. The “full off” mode is intended for off- road use only. Trailer sway control (tsc) ...

  • Page 281

    Period of time after the driver takes their foot off of the brake pedal. If the driver does not apply the throttle during this short period of time, the system will release brake pressure and the vehicle will roll down the hill. The system will release brake pressure in proportion to the amount of t...

  • Page 282

    Warning! • if you use a trailer brake controller with your trailer, your trailer brakes may be activated and deactivated with the brake switch. If so, when the brake pedal is released, there may not be enough brake pressure to hold the vehicle and trailer on a hill and this could cause a collision w...

  • Page 283

    Hill descent control (hdc) – four-wheel drive models with nv245 two–speed transfer case only hdc maintains vehicle speed while descending hills during off-road driving situations and is available in 4wd low range only. To enable hdc (transfer case must be in 4wd low range), press the hdc switch. If ...

  • Page 284

    And will only activate when the vehicle is descending a hill. It will usually not activate on level ground. The hdc speed may be adjusted by the driver to suit the driving conditions. The speed corresponds to the trans- mission gear selected. • 1st = 1 mph (1.6 km/h) • 2nd = 2.5 mph (4 km/h) • 3rd =...

  • Page 285

    Warning! Hdc is only intended to assist the driver in control- ling vehicle speed when descending hills. The driver must remain attentive to the driving conditions and is responsible for maintaining a safe vehicle speed. Esp/bas warning light and esp/tcs indicator light the malfunction indicator lig...

  • Page 286

    Tire safety information tire markings note: • p (passenger) - metric tire sizing is based on u.S. Design standards. P-metric tires have the letter “p” molded into the sidewall preceding the size designa- tion. Example: p215/65r15 95h. • european-metric tire sizing is based on european design standar...

  • Page 287

    Tires designed to this standard have the letter “t” molded into the sidewall preceding the size designa- tion. Example: t145/80d18 103m. • high flotation tire sizing is based on u.S. Design standards and it begins with the tire diameter molded into the sidewall. Example: 31x10.5 r15 lt. Tire sizing ...

  • Page 288

    Example: 15 = rim diameter in inches (in) service description: 95 = load index — a numerical code associated with the maximum load a tire can carry h = speed symbol — a symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating cond...

  • Page 289

    Tire identification number (tin) the tin may be found on one or both sides of the tire, however, the date code may only be on one side. Tires with white sidewalls will have the full tin, including the date code, located on the white sidewall side of the tire. Look for the tin on the outboard side of...

  • Page 290

    Tire loading and tire pressure tire placard location note: the proper cold tire inflation pressure is listed on the driver’s side b-pillar. Tire and loading information placard this placard tells you important information about the: 1) number of people that can be carried in the vehicle 2) total wei...

  • Page 291

    Note: under a maximum loaded vehicle condition, gross axle weight ratings (gawrs) for the front and rear axles must not be exceeded. For further information on gawrs, vehicle loading, and trailer towing, refer to “vehicle loading” in this section. To determine the maximum loading conditions of your ...

  • Page 292

    6. If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle. Note: • the following table shows examples on how to calcu- late total load, cargo...

  • Page 293

    5 starting and operating 293.

  • Page 294

    Warning! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. Tires — general information tire pressure proper tire inflation pressur...

  • Page 295

    Warning! (continued) • unequal tire pressures from one side of the ve- hicle to the other can cause the vehicle to drift to the right or left. • always drive with each tire inflated to the recom- mended cold tire inflation pressure. Economy improper inflation pressures can cause uneven wear patterns...

  • Page 296

    Caution! After inspecting or adjusting the tire pressure, al- ways reinstall the valve stem cap (if equipped). This will prevent moisture and dirt from entering the valve stem, which could damage it. Inflation pressures specified on the placard are always cold tire inflation pressure. Cold tire infl...

  • Page 297

    Tire pressures for high speed operation the manufacturer advocates driving at safe speeds within posted speed limits. Where speed limits or condi- tions are such that the vehicle can be driven at high speeds, maintaining correct tire inflation pressure is very important. Increased tire pressure and ...

  • Page 298

    Warning! Temporary use spare tires are for emergency use only. With these tires, do not drive more than 50 mph (80 km/h). Temporary use spare tires have limited tread life. When the tread is worn to the tread wear indicators, the temporary use spare tire needs to be replaced. Be sure to follow the w...

  • Page 299

    Warning! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause tire dam- age or failure. A tire could explode and injure some- one. Do not spin your vehicle’s wheels faster than 35 mph (55 km/h) when you are stuck, and do not let anyone near a spinning wheel no...

  • Page 300

    Life of tire the service life of a tire is dependent upon various factors including but not limited to: • driving style • tire pressure • distance driven warning! Tires and the spare tire should be replaced after six years, regardless of the remaining tread. Failure to follow this warning can result...

  • Page 301

    Warning! • do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change sus- pension dimensions and performance characteris- tics, resulting in changes to steering, handling, and braking of your vehicle. This can caus...

  • Page 302

    • for vehicles equipped with 18 inch wheels, do not install tire chains or traction devices on tires larger than 235/60r18xl. Tires larger than this may not provide sufficient body clearance with chains or other traction devices. • manufacturer recommends a cold inflation pressure of 38 psi (262 kpa...

  • Page 303

    Note: the premium tire pressure monitor system will automatically locate the pressure values displayed in the correct vehicle position following a tire rotation. The suggested rotation method is the “forward-cross” shown in the following diagram. Tire pressure monitor system (tpms) the tire pressure...

  • Page 304

    The tpms will warn the driver of a low tire pressure if the tire pressure falls below the low pressure warning threshold for any reason, including low temperature effects, or natural pressure loss through the tire. The tpms will continue to warn the driver of low tire pressure as long as the conditi...

  • Page 305

    Caution! • the tpms has been optimized for the original equipment tires and wheels. Tpms pressures have been established for the tire size equipped on your vehicle. Undesirable system operation or sensor damage may result when using replacement equipment that is not of the same size, type, and/or st...

  • Page 306

    • seasonal temperature changes will affect tire pressure, and the tpms will monitor the actual tire pressure in the tire. Base system the tire pressure monitor system (tpms) uses wireless technology with wheel rim-mounted electronic sensors to monitor tire pressure levels. Sensors, mounted to each w...

  • Page 307

    Pressures have been received. The vehicle may need to be driven for up to 20 minutes above 15 mph (24 km/h) to receive this information. The tire pressure monitoring telltale light will flash on and off for 75 seconds, and remain on solid when a system fault is detected. In addition, a “check tpm sy...

  • Page 308

    • if your vehicle is not equipped with a matching full-size spare wheel and tire assembly, it does not have a tire pressure monitoring sensor in the spare tire. The tpms will not be able to monitor the tire pressure. If you install the spare tire, in place of a road tire, that has a pressure below t...

  • Page 309

    The tire pressure monitor system (tpms) consists of the following components: • receiver module • four tire pressure monitoring sensors • three trigger modules (mounted in three of the four wheel wells) • various tire pressure monitoring system messages, which display in the electronic vehicle infor...

  • Page 310

    Note: your system can be set to display pressure units in psi, kpa, or bar. Should a low tire condition occur on any of the four active road tire(s), you should stop as soon as possible, and inflate the low tire(s) that is “flashing” on the graphic display to the vehicle’s recommended cold tire pres...

  • Page 311

    If the ignition key is cycled, this sequence will repeat, providing the system fault still exists. If the system fault no longer exists, the tire pressure monitoring telltale light will no longer flash, the ⬙ check tpm system ⬙ message will not be present, and a pressure value will be displayed inst...

  • Page 312

    Received from the tpm sensors. However, the system still needs to be serviced as long as the ⬙ check tpm system ⬙ message exists. Note: • if your vehicle is equipped with a matching full-size spare wheel and tire assembly, it has a tire pressure monitoring sensor, and can be monitored by the tire pr...

  • Page 313

    Tire pressure monitoring telltale light will flash on and off for 75 seconds and then remain on solid, and the evic will display a ⬙ check tpm system ⬙ message for three seconds and then display dashes (- -) in place of the pressure value. Once you repair or replace the original road tire, and reins...

  • Page 314

    Fuel requirements 3.7 engine all engines (except 5.7l engines) are de- signed to meet all emissions regulations and provide excellent fuel economy and performance when using high-quality un- leaded “regular” gasoline having an oc- tane rating of 87. The use of premium gasoline is not recommended, as...

  • Page 315

    Reformulated gasoline many areas of the country require the use of cleaner burning gasoline referred to as “reformulated gasoline.” reformulated gasoline contains oxygenates, and are spe- cifically blended to reduce vehicle emissions and im- prove air quality. The manufacturer supports the use of re...

  • Page 316

    • obd ii “malfunction indicator light” on • poor engine performance • poor cold start and cold drivability • increased risk for fuel system component corrosion to fix a non-ffv vehicle inadvertently fueled once with e-85 perform the following: • drain the fuel tank (see your authorized dealer) • cha...

  • Page 317

    Conditions and would result in additional cost. Therefore, you should not have to add anything to the fuel. Fuel system cautions caution! Follow these guidelines to maintain your vehicle’s performance: • the use of leaded gas is prohibited by federal law. Using leaded gasoline can impair engine perf...

  • Page 318

    • do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas which can kill. Never run the engine in a closed area, such as a garage, and never sit in a parked vehicle with the engine running for an extended period. If the vehicle is stopped in an open area with the engi...

  • Page 319

    Caution! • damage to the fuel system or emission control system could result from using an improper fuel cap (gas cap). A poorly fitting cap could let impu- rities into the fuel system. Also, a poorly fitting aftermarket cap can cause the “malfunction indi- cator light” (mil) to illuminate, due to f...

  • Page 320

    Loose fuel filler cap message if the vehicle diagnostic system determines that the fuel filler cap is loose, improperly installed, or damaged, a “check gascap” message will be displayed in the evic (electronic vehicle information center). Refer to “electronic vehicle information center” in section 4...

  • Page 321

    This label contains the month and year of manufacture, gross vehicle weight rating (gvwr), gross axle weight rating (gawr) front and rear, and vehicle identification number (vin). A month-day-hour (mdh) number is included on this label and indicates the month, day, and hour of manufacture. The bar c...

  • Page 322

    Inflation pressure this is the cold tire inflation pressure for your vehicle for all loading conditions up to full gawr. Curb weight the curb weight of a vehicle is defined as the total weight of the vehicle with all fluids, including vehicle fuel, at full capacity conditions, and with no occupants ...

  • Page 323

    Caution! Do not load your vehicle any heavier than the gvwr or the maximum front and rear gawr. If you do, parts on your vehicle can break, or it can change the way your vehicle handles. This could cause you to lose control. Also, overloading can shorten the life of your vehicle. Trailer towing in t...

  • Page 324

    Gross combination weight rating (gcwr) the gcwr is the total permissible weight of your vehicle and trailer when weighed in combination. Note: the gcwr rating includes a 150 lbs (68 kg) allowance for the presence of a driver. Gross axle weight rating (gawr) the gawr is the maximum capacity of the fr...

  • Page 325

    Weight-distributing hitch a weight-distributing hitch system works by applying leverage through spring (load) bars. They are typically used for heavier loads, to distribute trailer tongue weight to the tow vehicle’s front axle and the trailer axle(s). When used in accordance with the manufacturer’s ...

  • Page 326

    Without weight-distributing hitch (incorrect) with weight-distributing hitch (correct) 326 starting and operating.

  • Page 327

    Trailer hitch classification your vehicle may be factory equipped for safe towing of trailers weighing over 3,500 lbs (1 587 kg) with the optional trailer tow prep package. See your authorized dealer for package content. The following chart provides the industry standard for the maximum trailer weig...

  • Page 328

    All trailer hitches should be professionally installed on your vehicle. Trailer towing weights (maximum trailer weight ratings) the following chart provides the maximum trailer weight ratings towable for your given drivetrain. Engine model gcwr (gross com- bined wt. Rating) frontal area max. Gtw (gr...

  • Page 329

    Note: the trailer tongue weight must be considered as part of the combined weight of occupants and cargo, and should never exceed the weight referenced on the tire and loading information placard. Refer to the “tire– safety information” section in this manual. Trailer and tongue weight always load a...

  • Page 330

    Note: remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options, or dealer-installed options, must be considered as part of the total load on your vehicle. Refer to the tire and loading information plac- ard in the “tire—safety i...

  • Page 331

    • when hauling cargo or towing a trailer, do not over- load your vehicle or trailer. Overloading can cause a loss of control, poor performance or damage to brakes, axle, engine, transmission, steering, suspension, chas- sis structure or tires. • safety chains must always be used between your vehicle...

  • Page 332

    − check the trailer tires for proper tire inflation pres- sures before trailer usage. − check for signs of tire wear or visible tire damage before towing a trailer. Refer to “tires–general infor- mation” in this section. − when replacing tires, refer to “tires–general informa- tion” in this section....

  • Page 333

    Warning! • do not connect trailer brakes to your vehicle’s hydraulic brake lines. It can overload your brake system and cause it to fail. You might not have brakes when you need them and could have an accident. • towing any trailer will increase your stopping distance. When towing, you should allow ...

  • Page 334

    Four-pin connector 1 — female pins 4 — park 2 — male pin 5 — left stop/turn 3 — ground 6 — right stop/turn seven-pin connector 1 — battery 5 — ground 2 — backup lamps 6 — left stop/turn 3 — right stop/turn 7 — running lamps 4 — electric brakes 334 starting and operating.

  • Page 335

    Towing tips before setting out on a trip, practice turning, stopping and backing the trailer in an area away from heavy traffic. Automatic transmission the drive range can be selected when towing. How- ever, if frequent shifting occurs while in this range, the tow/haul mode (if equipped) or a lower ...

  • Page 336

    Cooling system to reduce potential for engine and transmission over- heating, take the following actions: − city driving when stopped for short periods of time, shift the trans- mission into neutral and increase engine idle speed. − highway driving reduce speed. − air conditioning turn off temporari...

  • Page 337

    Towing — quadra-trac i 姞 (single-speed transfer case) four-wheel drive models recreational towing is not allowed. This model does not have a neutral position in the transfer case. Towing — quadra–trac ii 姞 /quadra–drive 姞 ii four-wheel drive models caution! Front or rear wheel lifts should not be us...

  • Page 338

    Complete. A “4wd system in neutral” message will display on the evic (electronic vehicle information center). Refer to “electronic vehicle information center (evic)” in section 4 of this manual. 5. Start the engine. 6. Shift the transmission into drive. 7. Release the brake pedal and ensure that the...

  • Page 339

    Caution! Transmission damage may occur if the transmission is shifted into park with the transfer case in neu- tral and the engine running. With the transfer case in neutral ensure that the engine is off prior to shifting the transmission into park (refer to steps 7 and 8 above). Shifting out of neu...

  • Page 340

    5. Shift the transmission into park. 6. Start the engine. 7. Shift the transmission into drive. Note: when shifting out of transfer case neutral, turning the engine off may be required to avoid gear clash. Warning! You or others could be injured if you leave the vehicle unattended with the transfer ...

  • Page 341: Contents

    What to do in emergencies contents 䡵 hazard warning flashers . . . . . . . . . . . . . . . . 342 䡵 if your engine overheats . . . . . . . . . . . . . . . . 342 䡵 jacking and tire changing . . . . . . . . . . . . . . . 343 ▫ jack location . . . . . . . . . . . . . . . . . . . . . . . 344 ▫ spare tire...

  • Page 342

    Hazard warning flashers the hazard warning flasher switch is located on the switch bank just above the climate controls. Press the switch to turn on the hazard warning flasher. When the switch is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency. ...

  • Page 343

    Note: there are steps that you can take to slow down an impending overheat condition: • if your air conditioner (a/c) is on, turn it off. The a/c system adds heat to the engine cooling system and turning the a/c off can help remove this heat. • you can also turn the temperature control to maxi- mum ...

  • Page 344

    Jack location the scissor-type jack and tire changing tools are located in a compartment behind the third row seat. Refer to “cargo area features” in section 3 for further informa- tion. Spare tire stowage the spare tire is stowed under the rear of the vehicle by means of a cable winch mechanism. To...

  • Page 345

    Spare tire removal fit the jack handle extension over the drive nut. Use the lug wrench to rotate the nut counterclockwise until the spare is on the ground with enough slack in the cable to allow pulling the tire out from under the vehicle. Caution! The winch mechanism is designed for use with the j...

  • Page 346

    Warning! Do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to avoid being hit when operating the jack or changing the wheel. 2. Set the parking brake. 3. Place the shift lever into park 4. Turn off the ignition. 5. Turn on the hazard war...

  • Page 347

    Warning! (continued) • never start or run the engine with the vehicle on a jack. • do not let anyone sit in the vehicle when it is on a jack. • do not get under the vehicle when it is on a jack. • only use the jack in the positions indicated and for lifting this vehicle during a tire change. • if wo...

  • Page 348

    4. Locate the jack as shown. For the front axle, place it under the front lower control arm. Do not raise the vehicle until you are sure the jack is fully engaged. For the rear axle, place it under the axle near the wheel to be changed. Ensure the jack is closest to the inside of the wheel when jack...

  • Page 349

    5. Raise the vehicle by turning the jack screw clockwise. Raise the vehicle only until the tire just clears the surface and enough clearance is obtained to install the spare tire. Minimum tire lift provides maximum stability. Warning! Raising the vehicle higher than necessary can make the vehicle le...

  • Page 350

    9. Finish tightening the lug nuts. Push down on the wrench while tightening for increased leverage. Alternate nuts until each nut has been tightened twice. The correct wheel nut tightness is 95 ft lbs (130 n·m). If in doubt about the correct tightness, have them checked with a torque wrench by your ...

  • Page 351

    Jump-starting if the vehicle has a discharged battery, booster cables may be used to obtain a start from a booster battery or the battery in another vehicle. This type of start can be dangerous if done improperly, so follow this procedure carefully. Warning! • remove any metal jewelry such as watch ...

  • Page 352

    3. Turn off the heater, radio and all unnecessary electrical loads. 4. Connect one end of a jumper cable to the positive terminal of the booster battery. Connect the other end of the same cable to the positive terminal of the discharged battery. Warning! • do not permit vehicles to touch each other ...

  • Page 353

    Warning! Any procedure other than above could result in: • personal injury caused by electrolyte squirting out the battery vent. • personal injury or property damage due to battery explosion. Caution! Any procedure other than above could result in damage to the charging system of the booster vehicle...

  • Page 354

    Towing a disabled vehicle 2–wheel drive models only provided the transmission is operable, tow only in neu- tral at speeds not exceeding 30 mph (48 km/h), for distances of not more than 15 miles (24 km). Caution! Towing at more than 30 mph (48 km/h) or for more than 15 miles (24 km), can cause sever...

  • Page 355: Maintaining Your Vehicle

    Maintaining your vehicle contents 䡵 engine compartment – 3.7l . . . . . . . . . . . . . . 357 䡵 engine compartment – 5.7l . . . . . . . . . . . . . . 358 䡵 onboard diagnostic system – obd ii . . . . . . . 359 ▫ loose fuel filler cap message . . . . . . . . . . . 359 䡵 emissions inspection and mainte...

  • Page 356

    ▫ cooling system . . . . . . . . . . . . . . . . . . . . . 374 ▫ brake system . . . . . . . . . . . . . . . . . . . . . . . 379 ▫ front/rear axle fluid . . . . . . . . . . . . . . . . . 381 ▫ transfer case . . . . . . . . . . . . . . . . . . . . . . . 382 ▫ automatic transmission . . . . . . . . . ....

  • Page 357

    Engine compartment – 3.7l 1 — engine coolant reservoir 6 — washer fluid reservoir 2 — engine oil dipstick 7 — battery 3 — brake fluid reservoir 8 — engine oil fill 4 — power distribution center 9 — coolant pressure cap 5 — integrated power module 10 — air cleaner filter 7 maintaining your vehicle 35...

  • Page 358

    Engine compartment – 5.7l 1 — engine coolant reservoir 7 — washer fluid reservoir 2 — automatic transmission dipstick 8 — battery 3 — engine oil fill 9 — engine oil dipstick 4 — brake fluid reservoir 10 — coolant pressure cap 5 — power distribution center 11 — air cleaner filter 6 — integrated power...

  • Page 359

    Onboard diagnostic system – obd ii your vehicle is equipped with a sophisticated onboard diagnostic system called obd ii. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide ex...

  • Page 360

    The message will remain displayed until the vehicle diagnostic system can retest the fuel system. The test will perform the next time the vehicle is started, if the vehicle was keyed off above 40°f (4°c) outside temperature and the following vehicle start is above 40°f (4°c) outside temperature. It ...

  • Page 361

    2. Turn the ignition to the on position, but do not crank or start the engine. 3. If you crank or start the engine, you will have to start this test over. 4. As soon as you turn your key to the on position, you will see the mil symbol come on as part of a normal bulb check. 5. Approximately 15 secon...

  • Page 362

    Replacement parts use of genuine mopar 威 parts for normal/scheduled maintenance and repairs is highly recommended to en- sure the designed performance. Damage or failures caused by the use of non-mopar 威 parts for maintenance and repairs will not be covered by the manufacturer’s warranty. Dealer ser...

  • Page 363

    Caution! • failure to properly maintain your vehicle or per- form repairs and service when necessary could result in more costly repairs, damage to other components or negatively impact vehicle perfor- mance. Immediately have potential malfunctions examined by an authorized chrysler group llc dealer...

  • Page 364

    Caution! Overfilling or underfilling the crankcase will cause aeration or loss of oil pressure. This could damage your engine. Change engine oil the oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance. Refer to the “maintenance schedule” in s...

  • Page 365

    Engine oil viscosity sae 5w-20 engine oil is recommended for all operating temperatures. This engine oil improves low temperature starting and vehicle fuel economy. The engine oil filler cap also shows the recommended engine oil viscosity for your vehicle. For information on engine oil filler cap lo...

  • Page 366

    Environment. Contact your local authorized dealer, ser- vice station, or governmental agency for advice on how and where used oil and oil filters can be safely discarded in your area. Engine oil filter the engine oil filter should be replaced with a new filter at every oil change. Engine oil filter ...

  • Page 367

    Maintenance-free battery your vehicle is equipped with a maintenance-free battery. You will never have to add water, nor is periodic main- tenance required. Warning! • battery fluid is a corrosive acid solution and can burn or even blind you. Do not allow battery fluid to contact your eyes, skin or ...

  • Page 368

    Air conditioner maintenance for best possible performance, your air conditioner should be checked and serviced by an authorized dealer at the start of each warm season. This service should include cleaning of the condenser fins and a performance test. Drive belt condition should also be checked at t...

  • Page 369

    Note: use only manufacturer approved a/c system sealers, stop leak products, seal conditioners, compres- sor oil, and refrigerants. Refrigerant recovery and recycling r-134a air conditioning refrigerant is a hydrofluoro- carbon (hfc) that is endorsed by the environmental protection agency (epa) and ...

  • Page 370

    Operation of the wipers on dry glass for long periods may cause deterioration of the wiper blades. Always use washer fluid when using the wipers to remove salt or dirt from a dry windshield. Avoid using the wiper blades to wipe frost or ice from the windshield. Keep the blade rubber out of contact w...

  • Page 371

    Warning! Commercially available windshield washer solvents are flammable. They could ignite and burn you. Care must be exercised when filling or working around the washer solution. Exhaust system the best protection against carbon monoxide entry into the vehicle body is a properly maintained engine ...

  • Page 372

    Caution! The catalytic converter requires the use of unleaded fuel only. Leaded gasoline will destroy the effective- ness of the catalyst as an emissions control device and may seriously reduce engine performance and cause serious damage to the engine. Under normal operating conditions, the catalyti...

  • Page 373

    Warning! A hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your exhaust system. Do not park or operate your vehicle in areas where your exhaust system can contact anything that can burn. In unusual situati...

  • Page 374

    Cooling system warning! You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator. If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool. Never try to open a cooling system pressure cap when the radiat...

  • Page 375

    Cooling system — drain, flush, and refill if the engine coolant (antifreeze) is dirty and contains a considerable amount of sediment, clean and flush with reliable cooling system cleaner. Follow with a thorough rinsing to remove all deposits and chemicals. Properly dispose of the old engine coolant ...

  • Page 376

    Caution! (continued) • this vehicle has not been designed for use with propylene glycol-based engine coolant (anti- freeze). Use of propylene glycol-based engine coolant (antifreeze) is not recommended. Adding coolant your vehicle has been built with an improved engine coolant (antifreeze) that allo...

  • Page 377

    Please note that it is the owner’s responsibility to main- tain the proper level of protection against freezing ac- cording to the temperatures occurring in the area where the vehicle is operated. Note: mixing engine coolant (antifreeze) types will decrease the life of the engine coolant (antifreeze...

  • Page 378

    Rules for your community. To prevent ingestion by ani- mals and children, do not store ethylene glycol-based engine coolant (antifreeze) in open containers or allow it to remain in puddles on the ground. If ingested by a child or pet, seek emergency assistance immediately. Clean up any ground spills...

  • Page 379

    • do not overfill the coolant recovery bottle. • check the engine coolant (antifreeze) freeze point in the radiator and in the coolant recovery bottle. If engine coolant (antifreeze) needs to be added, contents of coolant recovery bottle must also be protected against freezing. • if frequent engine ...

  • Page 380

    Warning! Riding the brakes can lead to brake failure and possibly an accident. Driving with your foot resting or riding on the brake pedal can result in abnormally high brake temperatures, excessive lining wear, and possible brake damage. You would not have your full braking capacity in an emergency...

  • Page 381

    Warning! (continued) • to avoid contamination from foreign matter or moisture, use only new brake fluid or fluid that has been in a tightly closed container. Keep the master cylinder reservoir cap secured at all times. Brake fluid in a open container absorbs moisture from the air resulting in a lowe...

  • Page 382

    Selection of lubricant use only the manufacturer’s recommended fluid. Refer to “fluids, lubricants, and genuine parts” in this section for the correct fluid type. Transfer case fluid level check inspect the transfer case for fluid leaks. If a fluid leak is found, the transfer case fluid level can be...

  • Page 383

    Automatic transmission selection of lubricant it is important that the proper lubricant is used in the transmission to assure optimum transmission perfor- mance. Use only the manufacturer’s recommended trans- mission fluid. Refer to “fluids, lubricants, and genuine parts” in this section for the cor...

  • Page 384

    Caution! Do not use chemical flushes in your transmission as the chemicals can damage your transmission compo- nents. Such damage is not covered by the new vehicle limited warranty. Fluid level check (3.7l engine) regular fluid level checks are not required. For this reason, the dipstick is omitted....

  • Page 385

    Fluid level check (5.7l engine) check the fluid level while the transmission is at normal operating temperature. This occurs after at least 15 miles (25 km) of driving. At normal operating temperature the fluid cannot be held comfortably between the fingertips. To check the fluid level properly, the...

  • Page 386

    Caution! Be aware that if the fluid temperature is below 50°f (10°c) it may not register on the dipstick. Do not add fluid until the temperature is elevated enough to produce an accurate reading. 7. Check for leaks. Release parking brake. To prevent dirt and water from entering the transmission afte...

  • Page 387

    Caution! Under frequent heavy-duty driving conditions, change all lubricants, and lubricate body compo- nents, all driveline joints and steering linkage more often than in normal service, to prevent excessive wear. Appearance care and protection from corrosion protection of body and paint from corro...

  • Page 388

    • if insects, tar, or other similar deposits have accumu- lated on your vehicle, use mopar 威 super kleen bug and tar remover or equivalent to remove. • use a high quality cleaner wax, such as mopar 威 cleaner wax to remove road film, stains, and to protect your paint finish. Take care never to scratc...

  • Page 389

    • if your vehicle is damaged due to an accident or similar cause which destroys the paint and protective coating, have your vehicle repaired as soon as pos- sible. The cost of such repairs is considered the respon- sibility of the owner. • if you carry special cargo such as chemicals, fertilizers, d...

  • Page 390

    • for tough stains, apply mopar 威 total clean or a mild soap solution to a clean, damp cloth and remove the stain. Use a fresh, damp towel to remove soap residue. • for grease stains, apply mopar 威 multi-purpose cleaner or equivalent to a clean, damp cloth and remove the stain. Use a fresh, damp tow...

  • Page 391

    Warning! Do not use volatile solvents for cleaning purposes. Many are potentially flammable, and if used in closed areas, they may cause respiratory harm. Cleaning headlights your vehicle has plastic headlights that are lighter and less susceptible to stone breakage than glass headlights. Plastic is...

  • Page 392

    2. Dry with a soft tissue. Seat belt maintenance do not bleach, dye or clean the belts with chemical solvents or abrasive cleaners. This will weaken the fabric. Sun damage will also weaken the fabric. If the belts need cleaning, use mopar 威 total clean, a mild soap solution, or lukewarm water. Do no...

  • Page 393

    Cav- ity cartridge fuse mini-fuse description 3 10 amp red htd mirror (ebl) 4 20 amp yellow rr pwr out (b+) 5 10 amp red rr hvac (r/o) (commander only) 6 spare (b+) 7 20 amp yellow door locks (b+) 8 spare (b+) 9 20 amp yellow pwr outlet (b+) cav- ity cartridge fuse mini-fuse description 10 10 amp re...

  • Page 394

    Cav- ity cartridge fuse mini-fuse description 14 20 amp yellow cigar ltr (r/a) 15 10 amp red tire pressure tran- sponders (r/o) 16 10 amp red upper & lower switch bank, diag. Connector, cluster (b+) 17 15 amp blue flipper glass (b+) 19 spare (r/s) 20 10 amp red steering column con- trol module (sccm...

  • Page 395

    Underhood fuses (power distribution center) cav- ity cartridge fuse mini-fuse description 1 50 amp red ptc heater 1 (diesel only) cav- ity cartridge fuse mini-fuse description 2 40 amp green hid headlamps 3 50 amp red ptc heater 2 (diesel only) 4 30 amp pink power outlets 5 50 amp red ptc heater 3 (...

  • Page 396

    Cav- ity cartridge fuse mini-fuse description 10 — spare 11 40 amp green hvac blower 12 30 amp pink rear wiper, ign r/o 13 40 amp green rear window de- froster (ebl)/heated mirror 14 30 amp pink rear hvac (if equipped) 15 — spare 16 50 amp red asd 17 30 amp pink abs pump cav- ity cartridge fuse mini...

  • Page 397

    Cav- ity cartridge fuse mini-fuse description 26 15 amp blue brake lamps 27 20 amp yellow hd washer (if equipped) (export only) 28 30 amp green abs valves 29 20 amp yellow pcm batt (gasoline only) 30 — spare 31 — spare 32 15 amp blue powertrain control module (diesel only) 33 20 amp yellow final dri...

  • Page 398

    Cav- ity cartridge fuse mini-fuse description 43 25 amp natural coils, actuators 44 — spare underhood fuses (integrated power module) cav- ity cartridge fuse mini-fuse description 8 10 amp red lt park lamps 9 10 amp red trailer-tow park lamps 10 10 amp red rt park lamps 12 20 amp yellow front contro...

  • Page 399

    Cav- ity cartridge fuse mini-fuse description 17 20 amp yellow rear fog lamps (ex- port only) 18 20 amp yellow front control module (fcm) batt #1 19 20 amp yellow lt trailer-tow stop/ turn 20 20 amp yellow front control module (fcm) batt #3 21 20 amp yellow rt trailer-tow stop/ turn 22 30 amp pink f...

  • Page 400

    Vehicle storage if you are leaving your vehicle dormant for more than 21 days you may want to take steps to protect your battery. You may: • remove fuse #27 in the intelligent power module labeled ignition-off draw (iod#1). • or, disconnect the negative cable from the battery. • anytime you store yo...

  • Page 401

    Note: numbers refer to commercial bulb types that can be purchased from your authorized dealer. If a bulb needs to be replaced, visit your authorized dealer or refer to the applicable service manual. Bulb replacement head lamp 1. Open the hood. 2. Disconnect the electrical connector. 3. Turn the low...

  • Page 402

    Caution! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol. Front turn signal 1. Turn the steering wheel all the way to the left or right. 2. Reach into the front whe...

  • Page 403

    4. Turn the socket on the bottom of the front lamp unit housing 1/4 turn counterclockwise to unlock it. 5. Pull the socket and bulb straight out from the opening in the housing. 6. Disconnect the electrical connector. 7. Pull the base of the bulb straight out of the socket. Caution! Do not touch the...

  • Page 404

    2. Reach into the front wheel house ahead of the front wheel to unsnap and lift the cover over the access hole in the front of the wheel house splash shield. Access to the bulb can be gained through the wheel liner hole. 3. Reach through the access hole to access the back of the front fog lamp housi...

  • Page 405

    3. Pull the outboard side of the rear lamp unit rearward far enough to unsnap the two ball studs on the outboard side of the lamp housing from the two plastic grommets in the quarter outer panel. Pull the lamp unit rearward far enough away to access the bulbs. 4. Firmly grasp the appropriate bulb so...

  • Page 406

    5. Disconnect the electrical connector. 6. Pull the socket and bulb straight out from the opening in the housing. 7. Pull the base of the bulb straight out of the socket. Caution! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in con...

  • Page 407

    Fluids and capacities u.S. Metric fuel (approximate) 21 gallons 79 liters engine oil with filter 3.7 liter engine (sae 5w-20, api certified) 5 quarts 4.7 liters 5.7 liter engine (sae 5w-20, api certified) 7 quarts 6.6 liters cooling system * 3.7l engine (mopar 威 engine coolant/antifreeze 5 year/100,...

  • Page 408

    Fluids, lubricants, and genuine parts engine component fluid, lubricant, or genuine part engine coolant mopar 威 antifreeze/coolant 5 year/100,000 mile formula hoat (hy- brid organic additive technology) or equivalent. Engine oil use api certified sae 5w-20 engine oil, meeting the requirements of chr...

  • Page 409

    Chassis component fluid, lubricant, or genuine part automatic transmission mopar 威 atf+4 automatic transmission fluid or equivalent. Transfer case (nv140 single speed only) mopar 威 atf+4 automatic transmission fluid or equivalent. Transfer case (nv245 two speed only) mopar 威 nv 247/245 transfer case...

  • Page 411: Maintenance Schedules

    Maintenance schedules contents 䡵 emissions control system maintenance . . . . . . 412 䡵 maintenance schedule . . . . . . . . . . . . . . . . . . 412 ▫ required maintenance intervals . . . . . . . . . . 414 8 m a i n t e n a n c e s c h e d u l e s.

  • Page 412

    Emissions control system maintenance the scheduled maintenance services listed in bold type must be done at the times or mileages specified to ensure the continued proper functioning of the emissions control system. These and all other maintenance services in- cluded in this manual, should be done t...

  • Page 413

    • change your engine oil more often if you drive your vehicle off-road for an extended period of time. • under no circumstances should oil change intervals exceed 6,000 miles (10,000 km) or 6 months, whichever comes first. Your authorized dealer will reset the oil change indicator message after comp...

  • Page 414

    At each oil change • change the engine oil filter. • inspect the brake hoses and lines. Caution! Failure to perform the required maintenance items may result in damage to the vehicle. Required maintenance intervals refer to the maintenance schedules on the following pages for the required maintenanc...

  • Page 415

    6,000 miles (10,000 km) or 6 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. Odometer reading date repair order # dealer code signature authorized chrysler dealer 12,000 miles (20,000 km) or 12 months maintenance service schedule ❏ change the engine...

  • Page 416

    18,000 miles (30,000 km) or 18 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. ❏ inspect the front and rear axle fluid, change if using your vehicle for police, taxi, fleet, off-road or frequent trailer towing. Odometer reading date repair order # d...

  • Page 417

    30,000 miles (50,000 km) or 30 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. ❏ replace the engine air cleaner filter. ❏ replace the spark plugs (3.7l and 5.7l engines). ❏ adjust parking brake on vehicles equipped with four-wheel disc brakes. ❏ ins...

  • Page 418

    42,000 miles (70,000 km) or 42 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. Odometer reading date repair order # dealer code signature authorized chrysler dealer 48,000 miles (80,000 km) or 48 months maintenance service schedule ❏ change the engi...

  • Page 419

    54,000 miles (90,000 km) or 54 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. ❏ inspect the front and rear axle fluid, change if using your vehicle for police, taxi, fleet, off-road or frequent trailer towing. Odometer reading date repair order # d...

  • Page 420

    60,000 miles (100,000 km) or 60 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. ❏ replace the engine air cleaner filter. ❏ inspect the brake linings; replace if necessary. ❏ replace the ignition cables (3.7l engine). ❏ replace the spark plugs (3.7l ...

  • Page 421

    66,000 miles (110,000 km) or 66 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. Odometer reading date repair order # dealer code signature authorized chrysler dealer 72,000 miles (120,000 km) or 72 months maintenance service schedule ❏ change the en...

  • Page 422

    78,000 miles (130,000 km) or 78 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. Odometer reading date repair order # dealer code signature authorized chrysler dealer 84,000 miles (140,000 km) or 84 months maintenance service schedule ❏ change the en...

  • Page 423

    90,000 miles (150,000 km) or 90 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. ❏ replace the engine air cleaner filter. ❏ replace the spark plugs (3.7l and 5.7l engines). ❏ inspect and replace pcv valve if necessary. † ❏ adjust parking brake on veh...

  • Page 424

    96,000 miles (160,000 km) or 96 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. ❏ if using your vehicle for any of the following: dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. ❏ inspect the brake linings;...

  • Page 425

    108,000 miles (180,000 km) or 108 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. ❏ if using your vehicle for any of the following: dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. ❏ inspect the brake lining...

  • Page 426

    120,000 miles (200,000 km) or 120 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. ❏ replace the engine air cleaner filter. ❏ replace the ignition cables (3.7l engine). ❏ replace the spark plugs (3.7l and 5.7l engines). ❏ adjust parking brake on vehi...

  • Page 427

    132,000 miles (220,000 km) or 132 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. ❏ if using your vehicle for any of the following: dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. ❏ inspect the brake lining...

  • Page 428

    144,000 miles (240,000 km) or 144 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. ❏ if using your vehicle for any of the following: dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. ❏ inspect the brake lining...

  • Page 429

    † this maintenance is recommended by the manufacturer to the owner, but is not required to maintain emissions warranty. Warning! • you can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about...

  • Page 431: Contents

    If you need consumer assistance contents 䡵 suggestions for obtaining service for your vehicle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 433 ▫ prepare for the appointment . . . . . . . . . . . 433 ▫ prepare a list . . . . . . . . . . . . . . . . . . . . . . 433 ▫ be reasonable with r...

  • Page 432

    䡵 department of transportation uniform tire quality grades . . . . . . . . . . . . . . . . . . . . . . . . 439 ▫ treadwear . . . . . . . . . . . . . . . . . . . . . . . . . 439 ▫ traction grades . . . . . . . . . . . . . . . . . . . . . 439 ▫ temperature grades . . . . . . . . . . . . . . . . . . 44...

  • Page 433

    Suggestions for obtaining service for your vehicle prepare for the appointment if you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty. Discuss additional charges with the service manager. ...

  • Page 434

    This is why you should always talk to an authorized dealer’s service manager first. Most matters can be re- solved with this process. • if for some reason you are still not satisfied, talk to the general manager or owner of the authorized dealer- ship. They want to know if you need assistance. • if ...

  • Page 435

    Customer assistance for the hearing or speech impaired (tdd/tty) to assist customers who have hearing difficulties, the manufacturer has installed special tdd (telecommuni- cation devices for the deaf) equipment at its customer center. Any hearing or speech impaired customer, who has access to a tdd...

  • Page 436

    We appreciate that you have made a major investment when you purchased the vehicle. An authorized dealer has also made a major investment in facilities, tools, and training to assure that you are absolutely delighted with the ownership experience. You’ll be pleased with their sincere efforts to reso...

  • Page 437

    If nhtsa receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, nhtsa cannot become involved in individual problems between you, your authorized dealer, and the manufacturer. T...

  • Page 438

    Note: a street address is required when ordering manuals (no p.O. Boxes). • service manuals these comprehensive service manuals provide the information that students and professional technicians need in diagnosing/troubleshooting, problem solving, maintaining, servicing, and repairing chrysler group...

  • Page 439

    Call toll free at: • 1–800–890–4038 (u.S.) • 1–800–387–1143 (canada) or visit us on the worldwide web at: • www.Techauthority.Com department of transportation uniform tire quality grades the following tire grading categories were established by the national highway traffic safety administration. The...

  • Page 440

    Warning! The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics. Temperature grades the temperature grades are a (the highest), b, and c, representing the tire’s resistan...

  • Page 441: Index

    Index 10

  • Page 442

    Abs (anti-lock brake system) . . . . . . . . . . . . . . 269 adding fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . 318 adjustable pedals . . . . . . . . . . . . . . . . . . . . . . . . 117 air cleaner, engine (engine air cleaner filter) . . . 366 air conditioner maintenance . . . . . . ....

  • Page 443

    Fluid type . . . . . . . . . . . . . . . . . . . . . . . . . . . 383 special additives . . . . . . . . . . . . . . . . . . . . . . 383 torque converter . . . . . . . . . . . . . . . . . . . . . . 254 autostick . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 250 auxiliary electrical outlet ...

  • Page 444

    Cargo load floor . . . . . . . . . . . . . . . . . . . . . . . . 147 cargo (vehicle loading) . . . . . . . . . . . . . . . . . . . 320 cellular phone . . . . . . . . . . . . . . . . . . . . . . . . 85,223 center high mounted stop light . . . . . . . . . . . . 406 certification label . . . . . . . . ...

  • Page 445

    Pressure cap . . . . . . . . . . . . . . . . . . . . . . . . . 377 radiator cap . . . . . . . . . . . . . . . . . . . . . . . . . 377 selection of coolant (antifreeze) . . . . . . . . . 375,407 courtesy lights . . . . . . . . . . . . . . . . . . . . . . . . . 111 cruise light . . . . . . . . . . . ....

  • Page 446

    Electronic roll mitigation (erm) . . . . . . . . . . . . . 274 electronic speed control (cruise control) . . . . . . . 119 electronic stability program (esp) . . . . . . . . . . . . 275 electronic throttle control warning light . . . . . . 169 electronic vehicle information center (evic) . 167,170 e...

  • Page 447

    Exhaust gas caution . . . . . . . . . . . . . . 38,74,317,371 exhaust system . . . . . . . . . . . . . . . . . . . . . . . 74,371 extender, seat belt . . . . . . . . . . . . . . . . . . . . . . . . 48 exterior finish care . . . . . . . . . . . . . . . . . . . . . . 387 exterior lights . . . . . . . ...

  • Page 448

    Gasoline . . . . . . . . . . . . . . . . . . . . . . . . . . . . 314 gauge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169 materials added . . . . . . . . . . . . . . . . . . . . . . . 316 octane rating . . . . . . . . . . . . . . . . . . . . . . . . 314 requirements . . . . . . . . ...

  • Page 449

    Heated seats . . . . . . . . . . . . . . . . . . . . . . . . . . 90,91 heater, engine block . . . . . . . . . . . . . . . . . . . . . 245 high beam indicator . . . . . . . . . . . . . . . . . . . . . 161 high beam/low beam select (dimmer) switch . . 111 hill descent control . . . . . . . . . . . . ....

  • Page 450

    Key, sentry (immobilizer) . . . . . . . . . . . . . . . . . . . 17 key-in reminder . . . . . . . . . . . . . . . . . . . . . . . . . 17 keyless entry system . . . . . . . . . . . . . . . . . . . . . . 21 keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 knee bolster . . . . ....

  • Page 451

    Headlight switch . . . . . . . . . . . . . . . . . . . . . . 105 headlights . . . . . . . . . . . . . . . . . . . . . . . . . . . 401 headlights on with wipers . . . . . . . . . . . . . . . 106 high beam indicator . . . . . . . . . . . . . . . . . . . . 161 illuminated entry . . . . . . . . . . . . ...

  • Page 452

    Luggage rack (roof rack) . . . . . . . . . . . . . . . . . 150 lumbar support . . . . . . . . . . . . . . . . . . . . . . . . . 87 maintenance free battery . . . . . . . . . . . . . . . . . . 367 maintenance procedures . . . . . . . . . . . . . . . . . . . 362 maintenance schedule . . . . . . . . . ...

  • Page 453

    Oil, engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . 363 capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . 407 change interval . . . . . . . . . . . . . . . . . . . . . . . 364 dipstick . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 363 disposal . . . . . . ....

  • Page 454

    Inverter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143 lift gate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84 outlet (auxiliary electrical outlet) . . . . . . . . . . 140 seats . . . . . . . . . . ...

  • Page 455

    Reformulated gasoline . . . . . . . . . . . . . . . . . . . . 315 refrigerant . . . . . . . . . . . . . . . . . . . . . . . . . . . . 369 reminder, lights on . . . . . . . . . . . . . . . . . . . . . 110 reminder, seat belt . . . . . . . . . . . . . . . . . . . . . . . 47 remote control starting sys...

  • Page 456

    Pretensioners . . . . . . . . . . . . . . . . . . . . . . . . . . 46 reminder . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168 shoulder belt anchorage . . . . . . . . . . . . . . . . . 44 seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85 adjustment . . . . . . . ....

  • Page 457

    Snow plow . . . . . . . . . . . . . . . . . . . . . . . . . . . . 336 spare tire . . . . . . . . . . . . . . . . . . . . . . . . . . 297,344 specifications fuel (gasoline) . . . . . . . . . . . . . . . . . . . . . . . . 314 oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 364 spee...

  • Page 458

    Tire identification number (tin) . . . . . . . . . . . . . 289 tire markings . . . . . . . . . . . . . . . . . . . . . . . . . . 286 tire safety information . . . . . . . . . . . . . . . . . . . . 286 tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76,294,439 air pressure . . . . . . ....

  • Page 459

    Cooling system tips . . . . . . . . . . . . . . . . . . . . 336 hitches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 327 minimum requirements . . . . . . . . . . . . . . . . . 330 trailer and tongue weight . . . . . . . . . . . . . . . 329 wiring . . . . . . . . . . . . . . . . . . . . ...

  • Page 460

    Voice recognition system (vr) . . . . . . . . . . . . . . . 85 warning flasher, hazard . . . . . . . . . . . . . . . . . . 342 warning, roll over . . . . . . . . . . . . . . . . . . . . . . . . 5 warnings and cautions . . . . . . . . . . . . . . . . . . . . . 8 warranty information . . . . . . . . ....