1. DL manuals
  2. Jeep
  3. Automobile
  4. Grand Cherokee SRT 2018
  5. Owner's Manual

Jeep Grand Cherokee SRT 2018 Owner's Manual

Summary of Grand Cherokee SRT 2018

  • Page 1

    Grand cherokee srt o w n e r ’ s m a n u a l second edition printed in the u.S.A. 18wksrt-126-ab ©2017 fca us llc. All rights reserved. Jeep is a registered trademark of fca us llc. 2 0 1 8 stick with the specialists ® gr and cher ok ee sr t 20 18.

  • Page 2

    Installation of radio transmitting equipment special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained person- nel. The following must be obs...

  • Page 3

    Table of contents section page 1 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 graphical table of contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Page 5

    Introduction contents 䡵 introduction . . . . . . . . . . . . . . . . . . . . . . . . .4 䡵 how to use this manual . . . . . . . . . . . . . . .5 ▫ essential information . . . . . . . . . . . . . . . . . . . . . .5 ▫ symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 䡵 rollover war...

  • Page 6

    Introduction dear customer, congratulations on selecting your new vehicle. Be assured that it represents precision workman- ship, distinctive styling, and high quality. This is a specialized utility vehicle. It can go places and perform tasks that conventional passenger vehicles are not intended. It...

  • Page 7

    Described for technical and/or commercial reasons. For further information, contact an authorized dealer. If applicable, refer to the owners manual supplement for related information. Note: after reviewing the owner’s information, it should be stored in the vehicle for convenient referencing, and re...

  • Page 8

    Symbols consult the following table for a description of the symbols that may be used on your vehicle or throughout this owner’s manual: 6 introduction.

  • Page 9

    Rollover warning utility vehicles have a significantly higher rollover rate than other types of vehicles. This vehicle has a higher ground clearance and a higher center of gravity than many passenger vehicles. It is capable of performing better in a wide variety of off-road applications. Driven in a...

  • Page 10

    Warnings and cautions this owner’s manual contains warnings against oper- ating procedures that could result in a collision, bodily injury and/or death. It also contains cautions against procedures that could result in damage to your vehicle. If you do not read this entire owner’s manual, you may mi...

  • Page 11

    Graphical table of contents contents 䡵 front view . . . . . . . . . . . . . . . . . . . . . . . . . . .10 䡵 rear view. . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 䡵 instrument panel . . . . . . . . . . . . . . . . . . . . .12 䡵 interior . . . . . . . . . . . . . . . . . . . . . . . . ....

  • Page 12

    Front view front view 1 — hood/engine compartment 4 — wheels/tires 2 — windshield 5 — exterior mirrors 3 — headlights 6 — door handles 10 graphical table of contents.

  • Page 13

    Rear view rear view 1 — rear lights 2 — rear windshield wiper 3 — liftgate 2 graphical table of contents 11.

  • Page 14

    Instrument panel instrument panel 1 — air vents 4 — instrument cluster 2 — paddle shifter (-) 5 — paddle shifter (+) 3 — steering wheel 6 — glove compartment 12 graphical table of contents.

  • Page 15

    Interior interior features 1 — power window switches 4 — switch panel 2 — seats 5 — climate controls 3 — transmission gear selector 6 — radio 2 graphical table of contents 13.

  • Page 17

    Getting to know your vehicle contents 䡵 keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 ▫ key fob . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 䡵 ignition switch . . . . . . . . . . . . . . . . . . . . . . .24 ▫ keyless enter-n-go — ignition . . . . . . . . ....

  • Page 18

    ▫ keyless enter-n-go — passive entry . . . . . . . . .35 ▫ automatic unlock doors on exit . . . . . . . . . . . .40 ▫ child-protection door lock system — rear doors . . . . . . . . . . . . . . . . . . . . . . . . . . . .40 䡵 seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41 ▫ p...

  • Page 19

    ▫ automatic high beam — if equipped . . . . . . . .64 ▫ flash-to-pass . . . . . . . . . . . . . . . . . . . . . . . . . .65 ▫ automatic headlights — if equipped . . . . . . . . .65 ▫ parking lights and panel lights. . . . . . . . . . . . .65 ▫ headlights on automatically with wipers . . . . .65 ▫ he...

  • Page 20

    ▫ opening sunroof . . . . . . . . . . . . . . . . . . . . . . . .87 ▫ closing sunroof. . . . . . . . . . . . . . . . . . . . . . . . .88 ▫ wind buffeting . . . . . . . . . . . . . . . . . . . . . . . . .88 ▫ opening power shade . . . . . . . . . . . . . . . . . . . .88 ▫ closing power shade . . . . ...

  • Page 21

    Keys key fob your vehicle uses a keyless ignition system. The ignition system consists of a key fob with remote keyless entry (rke) and a start/stop push button ignition system. The remote keyless entry system consists of a key fob and keyless enter-n-go feature if equipped. Note: the key fob may no...

  • Page 22

    Note: in case the ignition switch does not change with the push of a button, the key fob may have a low or dead battery. In this situation, a back up method can be used to operate the ignition switch. Put the nose side of the key fob (side opposite of the emergency key) against the engine start/stop...

  • Page 23

    To lock the doors and liftgate push and release the lock button on the key fob to lock all doors and liftgate. The turn signal lights will flash and the horn will chirp to acknowledge the signal. Refer to “uconnect settings” located in “multimedia” for further programmable information. If the vehicl...

  • Page 24

    3. Remove the battery by turning the back cover over (battery facing downward) and tapping it lightly on a solid surface such as a table or similar and replace the battery. When replacing the battery, match the + sign on the battery to the + sign on the inside of the battery clip, located on the bac...

  • Page 25

    Programming additional key fobs programming the key fob may be performed by your authorized dealer. Request for additional key fobs note: only key fobs that are programmed to the vehicle electronics can be used to start and operate the vehicle. Once a key fob is programmed to a vehicle, it cannot be...

  • Page 26

    Ignition switch keyless enter-n-go — ignition this feature allows the driver to operate the ignition switch with the push of a button as long as the key fob is in the passenger compartment. The keyless push button ignition has several operating modes that are labeled and will illuminate when in posi...

  • Page 27

    Run • driving position. • all the electrical devices are available. Start • the engine will start. Warning! • when exiting the vehicle, always remove the key fob from the vehicle and lock your vehicle. • never leave children alone in a vehicle, or with access to an unlocked vehicle. • allowing child...

  • Page 28

    Note: the power window switches and power sunroof (if equipped) will remain active up to ten minutes after the ignition is cycled to the off position. Opening either front door will cancel this feature. The time for this feature is programmable. Warning! • before exiting a vehicle, always come to a ...

  • Page 29

    80° f (26.7° c), and the optional heated seats, and optional heated steering wheel in temperatures below 40° f (4.4° c). Refer to “heated seats” and “front ventilated seats” in “seats” in this section for further information. Note: • the vehicle must be equipped with an automatic trans- mission to b...

  • Page 30

    • system not disabled from previous remote start event • vehicle alarm system indicator flashing • ignition in stop/off position • fuel level meets minimum requirement warning! • do not start or run an engine in a closed garage or confined area. Exhaust gas contains carbon monox- ide (co) which is o...

  • Page 31

    To exit remote start mode without driving the vehicle push and release the remote start button one time or allow the remote start cycle to complete the entire 15-minute cycle. Note: to avoid unintentional shutdowns, the system will disable the one time push of the remote start button for two seconds...

  • Page 32

    Note: changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Sentry key the sentry key immobilizer system prevents unauthorized vehicle operation by disabling the engine. The system does not need to be armed o...

  • Page 33

    Replacement keys note: only key fobs that are programmed to the vehicle electronics can be used to start and operate the vehicle. Once a key fob is programmed to a vehicle, it cannot be programmed to any other vehicle. Caution! • always remove the key fobs from the vehicle and lock all doors when le...

  • Page 34

    General information the following regulatory statement applies to all radio frequency (rf) devices equipped in this vehicle: this device complies with part 15 of the fcc rules and with industry canada license-exempt rss standard(s). Operation is subject to the following two conditions: 1. This devic...

  • Page 35

    To disarm the system the vehicle security alarm can be disarmed using any of the following methods: • push the unlock button on the key fob. • grasp the passive entry door handle to unlock the door, refer to ⬙ doors ⬙ in ⬙ getting to know your vehicle ⬙ for further information. • cycle the ignition ...

  • Page 36

    Tamper alert if something has triggered the vehicle security alarm in your absence, the horn will sound three times and the exterior lights will blink three times when you disarm the vehicle security alarm. Check the vehicle for tampering. Doors manual door locks the power door locks can be manually...

  • Page 37

    Power door locks the power door lock switches are located on each front door panel. Push the switch to lock or unlock the doors. The driver’s door will unlock automatically if the keys are found inside the car when door lock button on trim is used to lock the door. Note: if the key fob is located ne...

  • Page 38

    Note: • passive entry may be programmed on/off; refer to “uconnect settings” in “multimedia” for further infor- mation. • the key fob may not be able to be detected by the vehicle passive entry system if it is located next to a mobile phone, laptop, or other electronic device; these devices may bloc...

  • Page 39

    To unlock from the passenger side with a valid passive entry key fob within 5 ft (1.5 m) of the passenger door handle, grab the front passenger door handle to unlock all four doors and the liftgate automati- cally. Note: all doors will unlock when the front passenger door handle is grabbed regardles...

  • Page 40

    To lock the vehicle’s doors and liftgate with one of the vehicle’s passive entry key fob within 5 ft (1.5 m) of the driver or passenger front door handles, pushing the passive entry lock button will lock the vehicle. Note: do not grab the door handle, when pushing the door handle lock button. This c...

  • Page 41

    • the passive entry system will not operate if the key fob battery is dead. The vehicle doors can also be locked by using the lock button located on the vehicle’s interior door panel. To unlock/enter the liftgate the liftgate passive entry unlock feature is built into the electronic liftgate release...

  • Page 42

    Automatic unlock doors on exit the doors will unlock automatically on vehicles with power door locks if: 1. The automatic unlock doors on exit feature is enabled. 2. All doors are closed. 3. The transmission gear selector was not in park, then is placed in park. 4. Any door is opened. Child-protecti...

  • Page 43

    • for emergency exit with the system engaged, pull up on the door lock knob (unlocked position), roll down the window, and open the door with the outside door handle. Warning! Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the...

  • Page 44

    Adjusting the seat forward or rearward the seat can be adjusted both forward and rearward. Push the seat switch forward or rearward. The seat will move in the direction of the switch. Release the switch when the desired position has been reached. Adjusting the seat up or down the height of the seats...

  • Page 45

    Seat. Push the switch forward to increase the lumbar support. Push the switch rearward to decrease the lumbar support. Pushing upward or downward on the switch will raise and lower the position of the support. Manual adjustment (rear seats) reclining rear seat to recline the seatback, lift the lever...

  • Page 46

    Driver memory seat — if equipped this feature allows the driver to store up to two different memory profiles for easy recall through a memory switch. Each memory profile contains desired position settings for the driver seat, side mirrors, and power tilt and telescopic steering column (if equipped) ...

  • Page 47

    3. Push and release the set (s) button on the memory switch. 4. Within five seconds, push and release either of the memory buttons (1) or (2). The instrument cluster dis- play will display which memory position has been set. Note: • memory profiles can be set without the vehicle in park, but the veh...

  • Page 48

    Driver one memory position recall • to recall the memory settings for driver one using the memory switch, push memory button (1) on the memory switch. • to recall the memory settings for driver one using the key fob, push the unlock button on the key fob linked to memory position 1. Driver two memor...

  • Page 49

    Note: the easy entry/exit feature is not enabled when the vehicle is delivered from the factory. The easy entry/ exit feature is enabled (or later disabled) through the programmable features in the uconnect system. Refer to “uconnect settings” in “multimedia”. Heated seats — if equipped on some mode...

  • Page 50

    Note: • once a heat setting is selected, heat will be felt within two to five minutes. • the engine must be running for the heated seats to operate. Vehicles equipped with remote start on models that are equipped with remote start, the heated seats can be programmed to come on during a remote start....

  • Page 51

    You can choose from hi, lo, or off heat settings. Amber indicator lights in each switch indicate the level of heat in use. Two indicator lights will illuminate for hi, one for lo and none for off. Push the switch once to select hi-level heating. Push the switch a second time to select lo-level heati...

  • Page 52

    The driver and front passenger cooler in higher ambient temperatures. The fans operate at two speeds, hi and lo. The front ventilated seats control buttons are located within the uconnect system. You can gain access to the control buttons through the climate screen or the controls screen. • press th...

  • Page 53

    Note: • do not fold the 60% rear seat down with the left outboard or rear center seat belt buckled. • do not fold the 40% rear seat down with the right outboard seat belt buckled. 2. Fold the rear seat completely forward. Note: you may experience deformation in the seat cush- ion from the seat belt ...

  • Page 54

    Head restraints head restraints are designed to reduce the risk of injury by restricting head movement in the event of a rear-impact. Head restraints should be adjusted so that the top of the head restraint is located above the top of your ear. Warning! • all occupants, including the driver, should ...

  • Page 55

    For comfort, the active head restraints can be tilted forward and rearward. To tilt the head restraint closer to the back of your head, pull forward on the bottom of the head restraint. Push rearward on the bottom of the head restraint to move the head restraint away from your head. Adjustment butto...

  • Page 56

    Note: • the head restraints should only be removed by qualified technicians, for service purposes only. If either of the head restraints require removal, see your authorized dealer. • in the event of deployment of an active head restraint, refer to “occupant restraints/resetting active head restrain...

  • Page 57

    Adjustment — rear seats the head restraints on the outboard seats are not adjust- able. They automatically fold forward when the rear seat is folded to a load floor position, but do not return to their normal position when the rear seat is raised. After return- ing either seat to its upright positio...

  • Page 58

    Note: for proper routing of a child seat tether, refer to “occupant restraints” in “safety” for further information. Warning! • a loose head restraint thrown forward in a collision or hard stop could cause serious injury or death to occupants of the vehicle. Always securely stow re- moved head restr...

  • Page 59

    To tilt the steering column, move the lever up or down as desired. To lengthen or shorten the steering column, pull the lever toward you or push the lever away from you as desired. Note: for vehicles equipped with driver memory seat, you can use your key fob or the memory switch on the driver’s door...

  • Page 60

    • press the heated steering wheel button a second time to turn the heating element off. Note: the engine must be running for the heated steering wheel to operate. Vehicles equipped with remote start on models that are equipped with remote start, the heated steering wheel can be programmed to come on...

  • Page 61

    Caution! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror. Apply the solution onto a clean cloth and wipe the mirror clean. Outside mirrors to receive maximum benefit, adjust the outside mirror(s) to center on the adjacent lane of traffic with...

  • Page 62

    Power mirrors the power mirror switch is located on the driver’s side door trim panel. The power mirror controls consist of mirror select buttons and a four-way mirror control switch. To adjust a mirror, push the mirror select button for the mirror that you want to adjust. Using the mirror control s...

  • Page 63

    Automatic power folding mirrors when the automatic fold mirrors feature is enabled, the exterior mirrors will fold in when exiting the vehicle (the ignition is off, all doors are closed, and the doors are locked). • if the exterior mirrors were auto-folded, they will unfold when the ignition is turn...

  • Page 64

    Tilt side mirrors in reverse (available with memory seat only) — if equipped tilt side mirrors in reverse provides automatic outside mirror positioning which will aid the driver’s view of the ground rearward of the front doors. Outside mirrors will move slightly downward from the present position wh...

  • Page 65

    To turn on the headlights, rotate the headlight switch clockwise. When the headlight switch is on, the parking lights, taillights, license plate light and instrument panel lights are also turned on. To turn off the headlights, rotate the headlight switch back to the o (off) position. Note: • your ve...

  • Page 66

    Multifunction lever the multifunction lever is located on the left side of the steering column. Daytime running lights — if equipped the daytime running lights (bright intensity) come on whenever the engine is running, and the transmission is not in the park position. The lights will remain on until...

  • Page 67

    • broken, muddy, or obstructed headlights and taillights of vehicles in the field of view will cause headlights to remain on longer (closer to the vehicle). Also, dirt, film, and other obstructions on the windshield or camera lens will cause the system to function improperly. If the windshield or au...

  • Page 68

    Note: when your headlights come on during the day- time, the instrument panel lights will automatically dim to the lower nighttime intensity. Headlight delay to aid in your exit, your vehicle is equipped with a headlight delay that will leave the headlights on for approximately up to 90 seconds. Thi...

  • Page 69

    Turn signals move the multifunction lever up or down and the arrows on each side of the instrument cluster flash to show proper operation of the front and rear turn signal lights. Note: if either light remains on and does not flash, or there is a very fast flash rate, check for a defective outside l...

  • Page 70

    Detent, will cause all the interior lights to go out. This is also known as the “party” mode because it allows the doors to stay open for extended periods of time without discharging the vehicle’s battery. Courtesy lights the courtesy lights can be turned on by pushing the top corner of the lens. To...

  • Page 71

    Each light can be turned on by pushing a switch on either side of the console. These buttons are backlit for night time visibility. To turn the lights off, push the switch a second time. The lights will also turn on when the unlock button on the remote keyless entry key fob is pushed. Ambient light ...

  • Page 72

    Dimmer controls the brightness of the instrument panel lighting can be regulated by rotating the dimmer control up (brighter) or down (dimmer). When the headlights are on you can supplement the brightness of the instrument cluster dis- play, radio and overhead console by rotating the control to its ...

  • Page 73

    Wiper operation and the sixth detent for high wiper operation. Caution! Always remove any buildup of snow that prevents the windshield wiper blades from returning to the “park” position. If the windshield wiper switch is turned off, and the blades cannot return to the “park” position, damage to the ...

  • Page 74

    Windshield washer operation to use the washer, push on the end of the lever (toward the steering wheel) and hold while spray is desired. If the lever is pushed while in the intermittent setting, the wipers will turn on and operate for several wipe cycles after the end of the lever is released, and t...

  • Page 75

    Note: the mist feature does not activate the washer pump; therefore, no washer fluid will be sprayed on the windshield. The wash function must be used in order to spray the windshield with washer fluid. Rain sensing wipers — if equipped this feature senses rain or snowfall on the windshield and auto...

  • Page 76

    The rain sensing system has protection features for the wiper blades and arms, and will not operate under the following conditions: • low ambient temperature — when the ignition is first turned on, the rain sensing system will not operate until the wiper switch is moved, vehicle speed is greater tha...

  • Page 77

    Operation. When this rotary control is in the off position, rotating it downward will activate the rear washer pump which will continue to operate as long as the switch is held. Once the switch is released it will return to the off position and the wipers will cycle several times before returning to...

  • Page 78

    Control descriptions icon description max a/c button press and release to change the current setting, the indicator illuminates when max a/c is on. Performing this function again will cause the max a/c operation to switch into manual mode and the max a/c indicator will turn off. A/c button press and...

  • Page 79

    Icon description front defrost button the front defrost button changes the current airflow setting to defrost mode. The indicator illu- minates when this feature is on. Air comes from the windshield and side window demist out- lets. When the defrost button is selected, the blower level may increase....

  • Page 80

    Icon description faceplate knob touchscreen buttons blower control blower control is used to regulate the amount of air forced through the climate system. There are seven blower speeds available. The speeds can be selected using either the blower control knob on the faceplate or the buttons on the t...

  • Page 81

    Icon description floor mode floor mode air comes from the floor outlets. A slight amount of air is directed through the defrost and side window demister outlets. Mix mode mix mode air is directed through the floor, defrost, and side window demister outlets. This setting works best in cold or snowy c...

  • Page 82

    Climate control functions a/c (air conditioning) the air conditioning (a/c) button allows the operator to manually activate or deactivate the air conditioning sys- tem. When the air conditioning system is turned on, cool dehumidified air will flow through the outlets into the cabin. For improved fue...

  • Page 83

    Automatic temperature control (atc) — if equipped automatic operation 1. Push the auto button on the faceplate, or the auto button on the touchscreen on the automatic tempera- ture control (atc) panel. 2. Next, adjust the temperature you would like the system to maintain by adjusting the driver and ...

  • Page 84

    Winter operation to ensure the best possible heater and defroster perfor- mance, make sure the engine cooling system is functioning properly and the proper amount, type, and concentration of coolant is used. Use of the air recirculation mode during winter months is not recommended, because it may ca...

  • Page 85

    Operating tips chart 3 getting to know your vehicle 83.

  • Page 86

    Windows power window controls the window controls on the driver’s door control all the door windows. There are single window controls on each passenger door trim panel, which operate the passenger door windows. The window controls will operate only when the ignition is in the acc or on/run position....

  • Page 87

    To open the window part way, push the window switch down briefly and release it when you want the window to stop. To stop the window from going all the way down during the auto-down operation, pull up on the switch briefly. Auto-up feature with anti-pinch protection lift the window switch up, for a ...

  • Page 88

    Push and release the window lockout button again (the indicator light on the button will turn back off). Wind buffeting wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or ...

  • Page 89

    Warning! • never leave children unattended in a vehicle, or with access to an unlocked vehicle. Never leave the key fob in or near the vehicle, or in a location accessible to children. Do not leave the ignition of a vehicle equipped with keyless enter-n-go in the acc or on/run mode. Occupants, parti...

  • Page 90

    Note: if the sunshade is in the closed position when express or manual open operation is initiated the sun- shade will automatically open to the half open position prior to the sunroof opening. Closing sunroof express mode push the switch forward and release it within one-half second and the sunroof...

  • Page 91

    Position. Any release of the switch will stop the movement and the shade will remain in a partially opened condition until the switch is pushed again. Closing power shade express push the switch forward and release it within one-half second and the shade will close automatically from any position. I...

  • Page 92

    Sunroof maintenance use only a non-abrasive cleaner and a soft cloth to clean the glass panel. Ignition off operation note: • the power sunroof switch can remain active in acces- sory delay for up to approximately ten minutes after the vehicle’s ignition is placed to the off position. Opening either...

  • Page 93

    2. Reach under the hood, move safety latch to the left and lift the hood. To close the hood 1. Hold up the hood with one hand and with the other hand remove the support rod from its seat and reinsert it into the locking tab. 2. Lower the hood to approximately 12 inches (30 cm) from the engine compar...

  • Page 94

    To unlock/enter the liftgate the liftgate may be released in several ways: • key fob • outside handle • button on overhead console the liftgate passive entry unlock feature is built into the electronic liftgate release. With a valid passive entry key fob within 5 ft (1.5 m) of the liftgate, push the...

  • Page 95

    Warning! Driving with the liftgate open can allow poisonous exhaust gases into your vehicle. You and your passen- gers could be injured by these fumes. Keep the liftgate closed when you are operating the vehicle. Closing grasp the liftgate closing handle and initiate lowering the liftgate. Release t...

  • Page 96

    Note: • in the event of a power malfunction to the liftgate, an emergency liftgate latch release can be used to open the liftgate. The emergency liftgate latch release can be accessed through a snap-in cover located on the liftgate trim panel. • if liftgate is left open for an extended period of tim...

  • Page 97

    Warning! • driving with the liftgate open can allow poisonous exhaust gases into your vehicle. You and your pas- sengers could be injured by these fumes. Keep the liftgate closed when you are operating the vehicle. • if you are required to drive with the liftgate open, make sure that all windows are...

  • Page 98

    Retractable cargo area cover — if equipped note: the purpose of this cover is for privacy, not to secure loads. It will not prevent cargo from shifting or protect passengers from loose cargo. To cover the cargo area: 1. Grasp the cover at the center handle. Pull it over the cargo area. 2. Insert the...

  • Page 99

    Warning! In a collision, a loose cargo cover in the vehicle could cause injury. It could fly around in a sudden stop and strike someone in the vehicle. Do not store the cargo cover on the cargo floor or in the passenger compart- ment. Remove the cover from the vehicle when taken from its mounting. D...

  • Page 100

    Warning! (continued) only, not for passengers, who should sit in seats and use seat belts. • cargo tie-down hooks are not safe anchors for a child seat tether strap. In a sudden stop or accident, a hook could pull loose and allow the child seat to come loose. A child could be badly injured. Use only...

  • Page 101

    Before you begin programming homelink be sure that your vehicle is parked outside of the garage before you begin programming. For more efficient programming and accurate transmission of the radio-frequency signal it is recommended that a new battery be placed in the hand-held transmitter of the devi...

  • Page 102

    1. Place the ignition in the on/run position. 2. Place the hand-held transmitter 1 to 3 inches (3 to 8 cm) away from the homelink button you wish to program while keeping the homelink indicator light in view. 3. Push and hold the homelink button you want to program while you push and hold the hand-h...

  • Page 103

    Programming a non-rolling code for programming garage door openers manufactured before 1995. 1. Cycle the ignition to the on/run position. 2. Place the hand-held transmitter 1 to 3 inches (3 to 8 cm) away from the homelink button you wish to program while keeping the homelink indicator light in view...

  • Page 104

    The signal during programming. Similar to this canadian law, some u.S. Gate operators are designed to time-out in the same manner. It may be helpful to unplug the device during the cycling process to prevent possible overheating of the garage door or gate motor. 1. Cycle the ignition to the on/run p...

  • Page 105

    Using homelink to operate, push and release the programmed homelink button. Activation will now occur for the programmed device (i.E. Garage door opener, gate operator, security sys- tem, entry door lock, home/office lighting, etc.). The hand- held transmitter of the device may also be used at any t...

  • Page 106

    General information the following regulatory statement applies to all radio frequency (rf) devices equipped in this vehicle: this device complies with part 15 of the fcc rules and with industry canada license-exempt rss standard(s). Operation is subject to the following two conditions: 1. This devic...

  • Page 107

    To open the glove compartment, pull the release handle. Door storage large storage areas are built into the door panels for easy access. Opened glove compartment door panel storage 3 getting to know your vehicle 105.

  • Page 108

    Console features the center console contains both an upper and a lower storage area. To open the upper storage compartment, pull upward on the small latch located on the lid. Storage compartment storage compartment latches 106 getting to know your vehicle.

  • Page 109

    Lift upward on the larger of the latches to access the lower storage compartment. Your vehicle may have an optional cd or dvd player located in the center console. Warning! Do not operate this vehicle with a console compart- ment lid in the open position. Driving with the console compartment lid ope...

  • Page 110

    Overhead console the overhead console contains courtesy/reading lights and storage for sunglasses. Universal garage door opener (homelink), power liftgate and power sunroof switches may also be included, if equipped. Cupholders there are two cupholders for the front seat passengers located in the ce...

  • Page 111

    There are two cupholders for the rear seat passengers located in the fold-down center armrest. Electrical power outlets your vehicle is equipped with 12 volt (15 amp) power outlets that can be used to power cellular phones, small electronics and other low powered electrical accessories. The power ou...

  • Page 112

    The front power outlet is located inside the storage area on the center stack of the instrument panel. Push inward on the storage lid to open the compartment and gain access to this power outlet. In addition to the front power outlet, there is also a power outlet located in the storage area of the c...

  • Page 113

    The rear power outlet is located in the right rear cargo area. Note: the rear power outlet can be switched from switched “ignition” only to constant “battery” powered all the time. See your local authorized dealer for details. Rear power outlet power outlet right rear quarter panel fuse 3 getting to...

  • Page 114

    Warning! To avoid serious injury or death: • only devices designed for use in this type of outlet should be inserted into any 12 volt outlet. • do not touch with wet hands. (continued) warning! (continued) • close the lid when not in use and while driving the vehicle. • if this outlet is mishandled,...

  • Page 115

    Power inverter — if equipped there is a 115 volt, 150 watt inverter outlet located on the back of the center console to convert dc current to ac current. This outlet can power cellular phones, electronics and other low power devices requiring power up to 150 watts. Note: certain high-end video game ...

  • Page 116

    Sunglasses bin door at the front of the console, a compartment is provided for storing a pair of sunglasses. The storage compartment access is a “press/press” design. Press the chrome pad on the door to open. Press the chrome pad on the door to close. Roof luggage rack — if equipped the crossbars an...

  • Page 117

    • if any cargo (or any metallic object) is placed over the satellite radio antenna (if equipped), you may experi- ence interruption of satellite radio reception. For im- proved satellite radio reception, avoid placing the rear crossbar over the satellite radio antenna. Warning! Cargo must be securel...

  • Page 119

    Getting to know your instrument panel contents 䡵 instrument cluster . . . . . . . . . . . . . . . . . .118 ▫ instrument cluster descriptions. . . . . . . . . . . . .119 䡵 instrument cluster display . . . . . . . . . . .120 ▫ instrument cluster display location and controls . . . . . . . . . . . . . ...

  • Page 120

    Instrument cluster srt instrument cluster 118 getting to know your instrument panel.

  • Page 121

    Instrument cluster descriptions 1. Speedometer • indicates vehicle speed. 2. Tachometer • indicates the engine speed in revolutions per minute (rpm x 1000). 3. Temperature gauge • the temperature gauge shows engine coolant tem- perature. Any reading within the normal range indi- cates that the engin...

  • Page 122

    Instrument cluster display your vehicle will be equipped with an instrument cluster display, which offers useful information to the driver. With the ignition in the stop/off mode, opening/closing of a door will activate the display for viewing, and display the total miles, or kilometers, in the odom...

  • Page 123

    • stored messages • screen setup • diagnostic • speed warning the system allows the driver to select information by pushing the following buttons mounted on the steering wheel: • up arrow button push and release the up arrow button to scroll upward through the main menu items. • down arrow button pu...

  • Page 124

    Oil change reset your vehicle is equipped with an engine oil change indi- cator system. The “oil change required” message will display in the instrument cluster display for five seconds after a single chime has sounded, to indicate the next scheduled oil change interval. The engine oil change indi- ...

  • Page 125

    • oil change due • fuel low • service anti-lock brake system • service electronic throttle control • service power steering • cruise control off • cruise control ready • acc driver override • cruise control set to xxx mph • tire pressure screen with low tire(s) “inflate tire to xx” • service tire pr...

  • Page 126

    • doors open • liftgate open • hood open • shift not allowed • vehicle speed is too high to shift to d • vehicle speed is too high to shift to r • vehicle speed is too high to shift to p • service transmission • service shifter the reconfigurable telltales section are divided into the white, green, ...

  • Page 127

    Terrain — if equipped push and release the up or down arrow button until the terrain icon/title is highlighted in the instrument cluster display. Push and release the right or left arrow button to display the selec-track or drivetrain. • selec-track — if equipped • drivetrain: front wheel angle, t-c...

  • Page 128

    • 1/8 mile (200 meters) timer – best – last – recent – reaction time — if selected • 1/4 mile (400 meters) timer – best – last – recent – reaction time — if selected • braking distance – distance – from speed • current g-forces • peak g-forces • lap timer • lap history – will list the last four laps...

  • Page 129

    Push and release the set + or the set- button (located on the steering wheel) and the following will display in the instrument cluster display: acc set when acc is set, the set speed will display in the instrument cluster. The acc screen may display once again if any acc activity occurs, which may i...

  • Page 130

    • average – the display shows the average fuel economy (mpg, l/100 km, or km/l) since the last reset. • current – this display shows the current fuel economy (mpg, l/100 km, km/l) while driving. Trip info push and release the up or down arrow button until the trip menu title is displayed in the inst...

  • Page 131

    • outside temp • time • range • fuel economy average • fuel economy current • trip a • trip b upper right • none • compass • outside temp (default setting) • time • range • fuel economy average • fuel economy current • trip a • trip b defaults (restores all settings to default settings) • cancel • r...

  • Page 132

    The menu with (show/hide) means user can press ok button to choose show or hide this menu on the instrument cluster display. Diagnostics push and release the up or down arrow button until the diagnostics icon/title is highlighted in the instrument cluster display. Push and release the ok button to d...

  • Page 133

    Note: • the charging system is independent from load reduc- tion. The charging system performs a diagnostic on the charging system continuously. • if the battery charge warning light is on it may indicate a problem with the charging system. Refer to “battery charge warning light” in “warning lights ...

  • Page 134

    What to do when an electrical load reduction action message is present (“battery saver on” or “battery saver mode”) during a trip: • reduce power to unnecessary loads if possible: – turn off redundant lights (interior or exterior) – check what may be plugged in to power outlets +12v, 150w, usb ports...

  • Page 135

    To reset a trip function reset will only occur while a resettable function is selected (highlighted). Push and hold the ok button to clear the resettable function being displayed. Warning lights and messages red warning lights — air bag warning light this light indicates a fault with the air bag, an...

  • Page 136

    Warning! Driving a vehicle with the red brake light on is dangerous. Part of the brake system may have failed. It will take longer to stop the vehicle. You could have a collision. Have the vehicle checked immediately. Vehicles equipped with the anti-lock brake system (abs) are also equipped with ele...

  • Page 137

    — electronic throttle control (etc) warning light this light informs you of a problem with the electronic throttle control (etc) system. If a problem is detected while the vehicle is running, the light will either stay on or flash depending on the nature of the problem. Cycle the ignition when the v...

  • Page 138

    Note: if the vehicle is moving, there will also be a single chime. — oil pressure warning light this light indicates low engine oil pressure. If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible. A chime will sound when this light turns on. Do not operate...

  • Page 139

    — vehicle security warning light — if equipped this light will flash at a fast rate for approximately 15 seconds when the vehicle security alarm is arming, and then will flash slowly until the vehicle is disarmed. Yellow warning lights — adaptive cruise control fault warning light this light will tu...

  • Page 140

    • the “esc off indicator light” and the “esc indicator light” come on momentarily each time the ignition is placed in the on/run or acc/on/run position. • the esc system will make buzzing or clicking sounds when it is active. This is normal; the sounds will stop when esc becomes inactive. • this lig...

  • Page 141

    Several typical driving styles. In most situations, the ve- hicle will drive normally and will not require towing. When the engine is running, the mil may flash to alert serious conditions that could lead to immediate loss of power or severe catalytic converter damage. The vehicle should be serviced...

  • Page 142

    Caution! (continued) occurs, repair immediately using the dedicated tire repair kit and contact your authorized dealer as soon as possible. Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer...

  • Page 143

    Caution! The tpms has been optimized for the original equip- ment tires and wheels. Tpms pressures and warning have been established for the tire size equipped on your vehicle. Undesirable system operation or sensor damage may result when using replacement equip- ment that is not of the same size, t...

  • Page 144

    — lanesense indicator light — if equipped the lanesense indicator is solid green when both lane markings have been detected and the system is “armed” and ready to provide visual and torque warnings if an unintentional lane departure occurs. Refer to “lanesense — if equipped ⬙ in “starting and operat...

  • Page 145

    Custom mode srt indicator light this light will turn on when custom mode srt is active. Refer to “selec-track” in “starting and operating” for further information. — lanesense indicator light — if equipped when the lanesense system is on, but not armed, the lanesense indicator is solid white. This o...

  • Page 146

    The rear of the vehicle) to turn off the high beams. If the high beams are off, pull the lever toward you for a temporary high beam on, ⬙ flash to pass ⬙ scenario. Onboard diagnostic system — obd ii your vehicle is equipped with a sophisticated onboard diagnostic system called obd ii. This system mo...

  • Page 147

    Warning! (continued) • be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death. • access, or allow others to access, information stored in your vehicle systems, inc...

  • Page 148

    • the mil will not flash at all and will remain fully illuminated until you place the ignition in the off posi- tion or start the engine. This means that your vehicle’s obd ii system is ready and you can proceed to the i/m station. If your obd ii system is not ready, you should see your authorized d...

  • Page 149

    Safety contents 䡵 safety features . . . . . . . . . . . . . . . . . . . . . .148 ▫ anti-lock brake system (abs) . . . . . . . . . . . . .148 ▫ electronic brake control system . . . . . . . . . . . .149 䡵 auxiliary driving systems . . . . . . . . . . . . .163 ▫ blind spot monitoring (bsm) — if equipp...

  • Page 150

    Safety features anti-lock brake system (abs) the anti-lock brake system (abs) provides increased vehicle stability and brake performance under most brak- ing conditions. The system automatically prevents wheel lock, and enhances vehicle control during braking. The abs performs a self-check cycle to ...

  • Page 151

    Warning! (continued) • the capabilities of an abs equipped vehicle must never be exploited in a reckless or dangerous manner that could jeopardize the user’s safety or the safety of others. Abs is designed to function with the oem tires. Modifica- tion may result in degraded abs performance. Anti-lo...

  • Page 152

    If the “brake system warning light” remains on or comes on while driving, it indicates that the brake system is not functioning properly and that immediate service is re- quired. If the “brake system warning light” does not come on when the ignition is turned to the on/run mode, have the light repai...

  • Page 153

    The following conditions must be met in order for hsa to activate: • the feature must be enabled. • the vehicle must be stopped. • park brake must be off. • driver door must be closed. • the vehicle must be on a sufficient grade. • the gear selection must match vehicle uphill direction (i.E., vehicl...

  • Page 154

    For vehicles not equipped with an instrument cluster display, perform the following steps: 1. Center the steering wheel (front wheels pointing straight forward). 2. Shift the transmission into park. 3. Apply the parking brake. 4. Start the engine. 5. Rotate the steering wheel slightly more than one-...

  • Page 155

    Reduce engine power to provide enhanced acceleration and stability. A feature of the tcs, brake limited differential (bld), functions similar to a limited slip differential and controls the wheel spin across a driven axle. If one wheel on a driven axle is spinning faster than the other, the system w...

  • Page 156

    Warning! (continued) from loss of vehicle control due to inappropriate driver input for the conditions. Only a safe, attentive, and skillful driver can prevent accidents. The capa- bilities of an esc equipped vehicle must never be exploited in a reckless or dangerous manner which could jeopardize th...

  • Page 157

    Warning! • when in “partial off” mode, the tcs functionality of esc, (except for the limited slip feature described in the tcs section), has been disabled and the “esc off indicator light” will be illuminated. When in “partial off” mode, the engine power reduction feature of tcs is disabled, and the...

  • Page 158

    Warning! (continued) off” mode is only intended for off-highway or off- road use. • the electronic stability control (esc) cannot pre- vent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions. Esc cannot prevent all accident...

  • Page 159

    Electronic roll mitigation (erm) this system anticipates the potential for wheel lift by monitoring the driver’s steering wheel input and the speed of the vehicle. When erm determines that the rate of change of the steering wheel angle and vehicle’s speed are sufficient to potentially cause wheel li...

  • Page 160

    Warning! If tsc activates while driving, slow the vehicle down, stop at the nearest safe location, and adjust the trailer load to eliminate trailer sway. Ready alert braking (rab) ready alert braking may reduce the time required to reach full braking during emergency braking situations. It antici- p...

  • Page 161

    Hdc has three states: 1. Off (feature is not enabled and will not activate). 2. Enabled (feature is enabled and ready but activation conditions are not met, or driver is actively overriding with brake or throttle application). 3. Active (feature is enabled and actively controlling ve- hicle speed). ...

  • Page 162

    Driver override the driver may override hdc activation with throttle or brake application at anytime. Deactivating hdc hdc will be deactivated but remain available if any of the following conditions occur: • driver overrides hdc set speed with throttle or brake application. • vehicle speed exceeds 2...

  • Page 163

    Warning! Hdc is only intended to assist the driver in controlling vehicle speed when descending hills. The driver must remain attentive to the driving conditions and is re- sponsible for maintaining a safe vehicle speed. Selec speed control (ssc) — if equipped ssc is intended for off road driving in...

  • Page 164

    • 3rd = 1.8 mph (3 km/h) • 4th = 2.5 mph (4 km/h) • 5th = 3.1 mph (5 km/h) • 6th = 3.7 mph (6 km/h) • 7th = 4.3 mph (7 km/h) • 8th = 5 mph (8 km/h) • 9th = 5.6 mph (9 km/h) – if equipped • reverse = .6 mph (1 km/h) • neutral = 1.2 mph (2 km/h) • park = ssc remains enabled but not active note: • duri...

  • Page 165

    • the vehicle is driven greater than 40 mph (64 km/h) (ssc exits immediately). Feedback to the driver: the instrument cluster has an ssc icon and the ssc switch has an led which offer feedback to the driver about the state ssc is in. • the cluster icon and switch lamp will illuminate and remain on s...

  • Page 166

    When the vehicle is started, the bsm warning light will momentarily illuminate in both outside rear view mirrors to let the driver know that the system is operational. The bsm system sensors operate when the vehicle is in any forward gear or reverse. The bsm detection zone covers approximately one l...

  • Page 167

    Contamination so that the bsm system can function prop- erly. Do not block the area of the rear fascia where the radar sensors are located with foreign objects (bumper stickers, bicycle racks, etc.). The bsm system notifies the driver of objects in the detection zones by illuminating the bsm warning...

  • Page 168

    Entering from the side vehicles that move into your adjacent lanes from either side of the vehicle. Entering from the rear vehicles that come up from behind your vehicle on either side and enter the rear detection zone with a relative speed of less than 30 mph (48 km/h). Side monitoring rear monitor...

  • Page 169

    Overtaking traffic if you pass another vehicle slowly with a relative speed less than 15 mph (24 km/h) and the vehicle remains in the blind spot for approximately 1.5 seconds, the warning light will be illuminated. If the difference in speed between the two vehicles is greater than 15 mph (24 km/h),...

  • Page 170

    The bsm system will not alert you of objects that are traveling in the opposite direction of the vehicle in adjacent lanes. Warning! The blind spot monitoring system is only an aid to help detect objects in the blind spot zones. The bsm system is not designed to detect pedestrians, bicyclists, or an...

  • Page 171

    Rear cross path (rcp) the rear cross path (rcp) feature is intended to aid the driver when backing out of parking spaces where their vision of oncoming vehicles may be blocked. Proceed slowly and cautiously out of the parking space until the rear end of the vehicle is exposed. The rcp system will th...

  • Page 172

    Modes of operation three selectable modes of operation are available in the uconnect system. Refer to “uconnect settings” in “multi- media” for further information. Blind spot alert lights only when operating in blind spot alert mode, the bsm system will provide a visual alert in the appropriate sid...

  • Page 173

    2. This device must accept any interference received, in- cluding interference that may cause undesired opera- tion. Note: changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Forward collision warning (fcw)...

  • Page 174

    When the system determines a collision with the vehicle in front of you is no longer probable, the warning message will be deactivated. Note: • the minimum speed for fcw activation is 1 mph (2 km/h). • the fcw alerts may be triggered on objects other than vehicles such as guard rails or sign posts b...

  • Page 175

    Latter is at a farther distance than ⬙ medium ⬙ setting. This provides the most reaction time to avoid a possible colli- sion. Changing the fcw status to the “near” setting, allows the system to warn the driver of a possible collision with the vehicle in front when the distance between the vehicle i...

  • Page 176

    Service fcw warning if the system turns off, and the instrument cluster displays: • acc/fcw unavailable service required • cruise/fcw unavailable service required this indicates there is an internal system fault. Although the vehicle is still drivable under normal conditions, have the system checked...

  • Page 177

    Note: when filling warm tires, the tire pressure may need to be increased up to an additional 4 psi (30 kpa) above the recommended cold placard pressure in order to turn the tire pressure monitoring telltale light off. The system will automatically update and the tire pressure monitoring telltale li...

  • Page 178

    Note: • the tpms is not intended to replace normal tire care and maintenance, or to provide warning of a tire failure or condition. • the tpms should not be used as a tire pressure gauge while adjusting your tire pressure. • driving on a significantly under-inflated tire causes the tire to overheat ...

  • Page 179

    • various tire pressure monitoring system messages, which display in the instrument cluster, and a graphic displaying tire pressures • tire pressure monitoring telltale light tire pressure monitoring low pressure warnings the tire pressure monitoring telltale light will illuminate in the instrument ...

  • Page 180

    The tire pressure monitoring telltale light will extinguish once the updated tire pressure(s) have been received. The vehicle may need to be driven for up to 20 minutes above 15 mph (24 km/h) to receive this information. Service tpm system warning the tire pressure monitoring telltale light will fla...

  • Page 181

    Instrument cluster display will display a ⬙ service tpm system ⬙ message for five seconds and then display dashes (- -) in place of the pressure value. Once you repair or replace the original road tire, and reinstall it on the vehicle in place of the spare tire, the tpms will update automatically. I...

  • Page 182

    (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to o...

  • Page 183

    5. You should read the instructions provided with your child restraint to make sure that you are using it properly. 6. All occupants should always wear their lap and shoul- der belts properly. 7. The driver and front passenger seats should be moved back as far as practical to allow the front air bag...

  • Page 184

    Seat belts. The belt alert feature is active whenever the ignition switch is in the start or on/run position. Initial indication if the driver is unbuckled when the ignition switch is first in the start or on/run position, a chime will signal for a few seconds. If the driver or outboard front seat p...

  • Page 185

    Note: if beltalert has been deactivated and the driver or outboard front seat passenger (if equipped with outboard front passenger seat beltalert) is unbuckled the seat belt reminder light will turn on and remain on until the driver and outboard front seat passenger seat belts are buckled. Lap/shoul...

  • Page 186

    Warning! (continued) seat belt. Follow these instructions to wear your seat belt safely and to keep your passengers safe, too. • two people should never be belted into a single seat belt. People belted together can crash into one an- other in a collision, hurting one another badly. Never use a lap/s...

  • Page 187

    Warning! (continued) • a frayed or torn seat belt could rip apart in a collision and leave you with no protection. Inspect the seat belt system periodically, checking for cuts, frays, or loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the seat belt system. Seat ...

  • Page 188

    4. Position the lap belt so that it is snug and lies low across your hips, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug seat belt reduces the risk of sliding...

  • Page 189

    Lap/shoulder belt untwisting procedure use the following procedure to untwist a twisted lap/ shoulder belt. 1. Position the latch plate as close as possible to the anchor point. 2. At about 6 to 12 inches (15 to 30 cm) above the latch plate, grasp and twist the seat belt webbing 180 degrees to creat...

  • Page 190

    Note: the adjustable upper shoulder belt anchorage is equipped with an easy up feature. This feature allows the shoulder belt anchorage to be adjusted in the upward position without pushing or squeezing the release button. To verify the shoulder belt anchorage is latched, pull downward on the should...

  • Page 191

    Seat belts and pregnant women seat belts must be worn by all occupants including preg- nant women: the risk of injury in the event of an accident is reduced for the mother and the unborn child if they are wearing a seat belt. Position the lap belt snug and low below the abdomen and across the strong...

  • Page 192

    Switchable automatic locking retractor (alr) the seat belts in the passenger seating positions are equipped with a switchable automatic locking retractor (alr) which is used to secure a child restraint system. For additional information, refer to “installing child restraints using the vehicle seat b...

  • Page 193

    How to engage the automatic locking mode 1. Buckle the combination lap and shoulder belt. 2. Grasp the shoulder portion and pull downward until the entire seat belt is extracted. 3. Allow the seat belt to retract. As the seat belt retracts, you will hear a clicking sound. This indicates the seat bel...

  • Page 194

    Between the back of the occupant’s head and the ahr. This system is designed to help prevent or reduce the extent of injuries to the driver and front passenger in certain types of rear impacts. Note: the active head restraints (ahr) may or may not deploy in the event of a front or side impact. Howev...

  • Page 195

    Warning! (continued) restraints are placed in their proper positions in order to minimize the risk of neck injury in the event of a collision. • do not place items over the top of the active head restraint, such as coats, seat covers or portable dvd players. These items may interfere with the opera-...

  • Page 196

    Warning! Deployed ahrs are not able to best protect you in all types of collisions. Have deployed ahrs reset by an authorized dealer immediately. Supplemental restraint systems (srs) some of the safety features described in this section may be standard equipment on some models, or may be optional eq...

  • Page 197

    On/run position. After the self-check, the air bag warn- ing light will turn off. If the orc detects a malfunction in any part of the system, it turns on the air bag warning light, either momentarily or continuously. A single chime will sound to alert you if the light comes on again after initial st...

  • Page 198

    Service the vehicle immediately. For additional information regarding the redundant air bag warning light refer to “getting to know your instrument panel” section of this manual. Front air bags this vehicle has front air bags and lap/shoulder belts for both the driver and front passenger. The front ...

  • Page 199

    Warning! (continued) • never place a rear-facing child restraint in front of an air bag. A deploying passenger front air bag can cause death or serious injury to a child 12 years or younger, including a child in a rear-facing child restraint. • only use a rear-facing child restraint in a vehicle wit...

  • Page 200

    Rollover collisions. The front air bags will not deploy in all frontal collisions, including some that may produce sub- stantial vehicle damage — for example, some pole colli- sions, truck underrides, and angle offset collisions. On the other hand, depending on the type and location of impact, front...

  • Page 201

    Supplemental side air bags supplemental seat-mounted side air bags (sabs) this vehicle is equipped with supplemental seat-mounted side air bags (sabs). Supplemental seat-mounted side air bags (sabs) are located in the outboard side of the front seats. The sabs are marked with a “srs airbag” or “airb...

  • Page 202

    Warning! Do not use accessory seat covers or place objects between you and the side air bags; the performance could be adversely affected and/or objects could be pushed into you, causing serious injury. Supplemental side air bag inflatable curtains (sabics) this vehicle is equipped with supplemental...

  • Page 203

    The sabics may help reduce the risk of partial or complete ejection of vehicle occupants through side windows in certain side impact events. Warning! • do not mount equipment, or stack luggage or other cargo up high enough to block the deployment of the sabics. The trim covering above the side windo...

  • Page 204

    Warning! (continued) or killed. Occupants, including children, should never lean on or sleep against the door, side win- dows, or area where the side air bags inflate, even if they are in an infant or child restraint. • seat belts (and child restraints where appropriate) are necessary for your prote...

  • Page 205

    The sabics may help reduce the risk of partial or complete ejection of vehicle occupants through side windows in certain rollover or side impact events. Air bag system components note: the occupant restraint controller (orc) monitors the internal circuits and interconnecting wiring associated with e...

  • Page 206

    Irritation, move to fresh air. If the irritation continues, see your doctor. If these particles settle on your clothing, follow the garment manufacturer’s instructions for cleaning. Do not drive your vehicle after the air bags have deployed. If you are involved in another collision, the air bags wil...

  • Page 207

    Maintaining your air bag system warning! • modifications to any part of the air bag system could cause it to fail when you need it. You could be injured if the air bag system is not there to protect you. Do not modify the components or wiring, in- cluding adding any kind of badges or stickers to the...

  • Page 208

    These data can help provide a better understanding of the circumstances in which crashes and injuries occur. Note: edr data are recorded by your vehicle only if a non-trivial crash situation occurs; no data are recorded by the edr under normal driving conditions and no personal data (e.G., name, gen...

  • Page 209

    Note: • for additional information, refer to www.Safercar.Gov/ parents/index.Htm or call: 1–888–327–4236 • canadian residents should refer to transport canada’s website for additional information: http://www.Tc.Gc.Ca/ eng/motorvehiclesafety/safedrivers-childsafety-index-53.Htm summary of recommendat...

  • Page 210

    Infant and child restraints safety experts recommend that children ride rear-facing in the vehicle until they are two years old or until they reach either the height or weight limit of their rear-facing child restraint. Two types of child restraints can be used rear- facing: infant carriers and conv...

  • Page 211

    Warning! • improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the child restraint manufacturer’s directions exactly when installing an infant or child restraint. • after a child restraint i...

  • Page 212

    If the answer to any of these questions was “no,” then the child still needs to use a booster seat in this vehicle. If the child is using the lap/shoulder belt, check seat belt fit periodically and make sure the seat belt buckle is latched. A child’s squirming or slouching can move the belt out of p...

  • Page 213

    Lower anchors and tethers for children (latch) restraint system your vehicle is equipped with the child restraint anchorage system called latch, which stands for lower anchors and tethers for children. The latch system has three vehicle anchor points for installing latch-equipped child seats. There ...

  • Page 214

    Frequently asked questions about installing child restraints with latch what is the weight limit (child’s weight + weight of the child restraint) for using the latch anchorage system to attach the child restraint? 65 lbs (29.5 kg) use the latch anchorage system until the combined weight of the child...

  • Page 215

    Frequently asked questions about installing child restraints with latch can the rear-facing child restraint touch the back of the front passenger seat? Yes the child seat may touch the back of the front passenger seat if the child restraint manufacturer also allows contact. See your child restraint ...

  • Page 216

    Locating the upper tether anchorages there are tether strap anchorages behind each rear seating position located on the back of the seat. To access them, pull the carpeted floor panel away from the seat back, this will expose the top tether strap anchorages. Latch-compatible child restraint systems ...

  • Page 217

    Center seat latch warning! • do not install a child restraint in the center position using the latch system. This position is not ap- proved for installing child seats using the latch attachments. You must use the seat belt and tether anchor to install a child seat in the center seating position. • ...

  • Page 218

    Always follow the directions of the child restraint manu- facturer when installing your child restraint. Not all child restraint systems will be installed as described here. To install a latch-compatible child restraint if the selected seating position has a switchable automatic locking retractor (a...

  • Page 219

    6. Test that the child restraint is installed tightly by pulling back and forth on the child seat at the belt path. It should not move more than 1 inch (25.4 mm) in any direction. How to stow an unused switchable-alr (alr) seat belt: when using the latch attaching system to install a child restraint...

  • Page 220

    The seat belts in the passenger seating positions are equipped with a switchable automatic locking retractor (alr) that is designed to keep the lap portion of the seat belt tight around the child restraint so that it is not necessary to use a locking clip. The alr retractor can be “switched” into a ...

  • Page 221

    Frequently asked questions about installing child restraints with seat belts can the rear-facing child restraint touch the back of the front passenger seat? Yes contact between the front passenger seat and the child restraint is allowed, if the child re- straint manufacturer also allows contact. Can...

  • Page 222

    5. To lock the seat belt, pull down on the shoulder part of the belt until you have pulled all the seat belt webbing out of the retractor. Then, allow the webbing to retract back into the retractor. As the webbing retracts, you will hear a clicking sound. This means the seat belt is now in the autom...

  • Page 223

    You may need to move the seat forward to provide better access to the tether anchorage. If there is no top tether anchorage for that seating position, move the child restraint to another position in the vehicle if one is available. 2. To access the top tether strap anchorages behind the rear seat, p...

  • Page 224

    5. Attach the tether strap hook of the child restraint to the top tether anchorage as shown in the diagram. 6. Remove slack in the tether strap according to the child restraint manufacturer’s instructions. Warning! • the top tether anchorages are not visible until the gap panel is folded down. Do no...

  • Page 225

    Safety tips transporting passengers never transport passengers in the cargo area. Warning! • do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death. • it is extremely dangerous to ride in a cargo area, inside or outside of a v...

  • Page 226

    Vehicle, or when the underside or rear of the vehicle is damaged, have a competent mechanic inspect the complete exhaust system and adjacent body areas for broken, dam- aged, deteriorated, or mispositioned parts. Open seams or loose connections could permit exhaust fumes to seep into the passenger c...

  • Page 227

    Warning! An improperly attached, damaged, folded, or stacked floor mat, or damaged floor mat fasteners may cause your floor mat to interfere with the accelerator, brake, or clutch pedals and cause a loss of vehicle control. To prevent serious injury or death: • always securely attach your floor mat ...

  • Page 228

    Warning! (continued) • it is recommended to only use mild soap and water to clean your floor mats. After cleaning, always check your floor mat has been properly installed and is secured to your vehicle using the floor mat fasteners by lightly pulling mat. Periodic safety checks you should make outsi...

  • Page 229

    Warning! To prevent serious injury or death: • always remove any “track-use” equipment before driving on public roads. • always properly use your three-point seat belts when driving on public roads. • in a collision, you and your passengers can suffer much greater injuries if you are not properly bu...

  • Page 231

    Starting and operating contents 䡵 starting the engine . . . . . . . . . . . . . . . . . .232 ▫ automatic transmission . . . . . . . . . . . . . . . . . .232 ▫ normal starting . . . . . . . . . . . . . . . . . . . . . . . .233 ▫ if engine fails to start . . . . . . . . . . . . . . . . . .234 ▫ cold w...

  • Page 232

    ▫ adaptive cruise control (acc) operation . . . . .260 ▫ activating adaptive cruise control (acc) . . . . .260 ▫ to activate/deactivate . . . . . . . . . . . . . . . . . . .261 ▫ to set a desired acc speed. . . . . . . . . . . . . . .261 ▫ to cancel . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Page 233

    䡵 parksense active park assist system — if equipped . . . . . . . . . . . . . . . . . . . . . . . . . .294 ▫ enabling and disabling the parksense active park assist system . . . . . . . . . . . . . . . . . . . . . .295 ▫ parallel parking space assistance operation/display . . . . . . . . . . . . . ....

  • Page 234

    Starting the engine before starting your vehicle, adjust your seat, adjust the inside and outside mirrors, fasten your seat belt, and if present, instruct all other occupants to buckle their seat belts. Warning! • before exiting a vehicle, always come to a complete stop, then shift the automatic tra...

  • Page 235

    Caution! (continued) • shift into or out of reverse only after the vehicle has come to a complete stop and the engine is at idle speed. • before shifting into any gear, make sure your foot is firmly on the brake pedal. Normal starting to turn on the engine using the engine start/ stop button 1. The ...

  • Page 236

    Note: the system will automatically time out and the ignition will cycle to the off mode after 30 minutes of inactivity if the ignition is left in the acc or run (engine not running) mode and the transmission is in park. Engine start/stop button functions — with driv- er’s foot off the brake pedal (...

  • Page 237

    After starting the idle speed is controlled automatically, and it will decrease as the engine warms up. Engine break-in recommendations the following tips will be helpful in obtaining optimum performance and maximum durability for your new srt vehicle. Despite modern technology and world class manuf...

  • Page 238

    For the first 1500 miles (2414 km): • do not participate in track events, sport driving schools, or similar activities during the first 1500 mi (2414 km). Note: check engine oil with every refueling and add if necessary. Oil and fuel consumption may be higher through the first oil change interval. R...

  • Page 239

    When parking on a hill, it is important to turn the front wheels toward the curb on a downhill grade and away from the curb on an uphill grade. Apply the parking brake before placing the gear selector in park, otherwise the load on the transmission locking mechanism may make it difficult to move the...

  • Page 240

    Caution! If the brake warning light remains on with the park- ing brake released, a brake system malfunction is indicated. Have the brake system serviced by an au- thorized dealer immediately. Automatic transmission warning! • never use the park position as a substitute for the parking brake. Always...

  • Page 241

    Warning! (continued) • when exiting the vehicle, always make sure the ignition is in the off mode, remove the key fob from the vehicle, and lock the vehicle. • never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous...

  • Page 242

    Brake/transmission shift interlock system this vehicle is equipped with a brake transmission shift interlock system (btsi) that holds the transmission gear selector in park unless the brakes are applied. To shift the transmission out of park, the engine must be running and the brake pedal must be pr...

  • Page 243

    • some eco mode functions may be temporarily inhib- ited based on temperature and other factors. Note: eco mode is only available in auto, sport or track mode. Active noise cancellation — if equipped your vehicle is equipped with an active noise cancellation system. This system uses four microphones...

  • Page 244

    (+/-), will manually select the transmission gear, and will display the current gear in the instrument cluster. Note: if the gear selector cannot be moved to the park, reverse, or neutral position (when pushed forward) it is probably in the autostick (+/-) position (beside the drive position). In au...

  • Page 245

    • turn the ignition off. • remove the key fob from the vehicle. Warning! • never use the park position as a substitute for the parking brake. Always apply the parking brake fully when exiting the vehicle to guard against vehicle movement and possible injury or damage. • your vehicle could move and i...

  • Page 246

    Warning! (continued) touch the parking brake, brake pedal or the trans- mission gear selector. • do not leave the key fob in or near the vehicle (or in a location accessible to children), and do not leave the ignition in the acc or on/run mode. A child could operate power windows, other controls, or...

  • Page 247

    Warning! Do not coast in neutral and never turn off the ignition to coast down a hill. These are unsafe practices that limit your response to changing traffic or road conditions. You might lose control of the vehicle and have a collision. Caution! Towing the vehicle, coasting, or driving for any oth...

  • Page 248

    Transmission limp home mode transmission function is monitored electronically for ab- normal conditions. If a condition is detected that could result in transmission damage, transmission limp home mode is activated. In this mode, the transmission may operate only in certain gears, or may not shift a...

  • Page 249

    Autostick autostick is a driver-interactive transmission feature pro- viding manual shift control, giving you more control of the vehicle. Autostick allows you to maximize engine braking, eliminate undesirable upshifts and downshifts, and im- prove overall vehicle performance. This system can also p...

  • Page 250

    • the system will ignore attempts to upshift at too low of a vehicle speed. • holding the (-) paddle depressed, or holding the gear selector in the (-) position, will downshift the transmis- sion to the lowest gear possible at the current speed. • transmission shifting will be more noticeable when a...

  • Page 251

    Selec-track consists of the following positions: • sport – dry weather, on-road calibration. Performance based tuning that provides a rear wheel drive feel but with improved handling and acceleration over a two- wheel drive vehicle. This feature will reset to auto on an ignition cycle. • snow – tuni...

  • Page 252

    • track mode (available in terrain positions auto, track and custom.) — provides a full firm suspen- sion for an aggressive track experience. Refer to “srt drive modes” in the “multimedia” section for further information. Launch control — if equipped this vehicle is equipped with a launch control sy...

  • Page 253

    2. Press the “launch rpm set-up” button on the touch- screen. This screen will allow you to adjust your launch rpm’s for optimum launch/traction. 3. Press the “activate launch control” button on the touchscreen, follow instructions in the instrument clus- ter display. • make sure the vehicle is not ...

  • Page 254

    Guidelines for track use note: because of the extreme conditions encountered during track use, any damage or wear associated with track use may not be covered by warranty. • if your srt vehicle is equipped with drive modes they will alter the vehicle’s performance in various driving situations. It i...

  • Page 255

    Cold and adjusting based on ambient & track conditions is recommended. Tire pressure can be monitored via the instrument cluster display and can assist with adjustments. Track burnishing your brakes: to avoid “green lining fade” during track use, the brake pads and rotors must have a thermal burnish...

  • Page 256

    Fuel saver technology — if equipped this feature offers improved fuel economy by shutting off four of the engine’s eight cylinders during light load and cruise conditions. The system is automatic with no driver inputs or additional driving skills required. Note: this system may take some time to ret...

  • Page 257

    Speed control — if equipped when engaged, the speed control takes over accelerator operations at speeds greater than 25 mph (40 km/h). The speed control buttons are located on the right side of the steering wheel. Note: in order to ensure proper operation, the speed control system has been designed ...

  • Page 258

    Warning! Leaving the speed control system on when not in use is dangerous. You could accidentally set the system or cause it to go faster than you want. You could lose control and have an accident. Always leave the system off when you are not using it. To set a desired speed turn the speed control o...

  • Page 259

    Know your instrument panel” for more information. The speed decrement shown is dependant on the chosen speed unit of u.S. (mph) or metric (km/h): u.S. Speed (mph) • pushing the set (-) button once will result in a 1 mph decrease in set speed. Each subsequent tap of the button results in a decrease o...

  • Page 260

    To deactivate a soft tap on the brake pedal, pushing the canc button, or normal brake pressure while slowing the vehicle will deactivate the speed control without erasing the set speed from memory. Pushing the on/off button or turning the ignition switch off erases the set speed from memory. Adaptiv...

  • Page 261

    Warning! • adaptive cruise control (acc) is a convenience system. It is not a substitute for active driving involvement. It is always the driver’s responsibility to be attentive of road, traffic, and weather condi- tions, vehicle speed, distance to the vehicle ahead; and, most importantly, brake ope...

  • Page 262

    Adaptive cruise control (acc) operation the speed control buttons (located on the right side of the steering wheel) operates the acc system. Note: any chassis/suspension or tire size modifications to the vehicle will effect the performance of the adaptive cruise control and forward collision warning...

  • Page 263

    To activate/deactivate push and release the adaptive cruise control (acc) on/off button. The acc menu in the instrument cluster displays “acc ready.” to turn the system off, push and release the adaptive cruise control (acc) on/off button again. At this time, the system will turn off and the instrum...

  • Page 264

    If the system is set when the vehicle speed is below 20 mph (32 km/h), the set speed shall be defaulted to 20 mph (32 km/h). If the system is set when the vehicle speed is above 20 mph (32 km/h), the set speed shall be the current speed of the vehicle. Note: acc cannot be set if there is a stationar...

  • Page 265

    To resume if there is a set speed in memory push the res (resume) button and then remove your foot from the accelerator pedal. The instrument cluster display will display the last set speed. Note: • if your vehicle stays at standstill for longer than two seconds, then the system will cancel and the ...

  • Page 266

    • if the button is continually pushed, the set speed will continue to increase in 10 km/h increments until the button is released. The increase in set speed is reflected in the instrument cluster display. To decrease speed while acc is set, the set speed can be decreased by pushing the set (-) butto...

  • Page 267

    • the acc system maintains set speed when driving up hill and down hill. However, a slight speed change on moderate hills is normal. In addition, downshifting may occur while climbing uphill or descending downhill. This is normal operation and necessary to maintain set speed. When driving up hill an...

  • Page 268

    To increase the distance setting, push the distance setting — increase button and release. Each time the button is pushed, the distance setting increases by one bar (longer). To decrease the distance setting, push the distance setting — decrease button and release. Each time the button is pushed, th...

  • Page 269

    The maximum braking applied by acc is limited; how- ever, the driver can always apply the brakes manually, if necessary. Note: the brake lights will illuminate whenever the acc system applies the brakes. A proximity warning will alert the driver if acc predicts that its maximum braking level is not ...

  • Page 270

    While acc with stop is holding your vehicle at a stand- still, if the driver seatbelt is unbuckled or the driver door is opened, the acc with stop system will cancel and the brakes will release. A cancel message will display on the instrument cluster display and produce a warning chime. Driver inter...

  • Page 271

    • the instrument cluster display will return to the last display selected after five seconds of no acc display activity display warnings and maintenance “wipe front radar sensor in front of vehicle” warning the “acc/fcw unavailable wipe front radar sensor” warning will display and also a chime will ...

  • Page 272

    When the condition that deactivated the system is no longer present, the system will return to the “adaptive cruise control off” state and will resume function by simply reactivating it. Note: • if the “acc/fcw unavailable wipe front radar sen- sor” message occurs frequently (e.G. More than once on ...

  • Page 273

    Service acc/fcw warning if the system turns off, and the instrument cluster displays “acc/fcw unavailable service required” or “cruise/ fcw unavailable service required”, there may be an internal system fault or a temporary malfunction that limits acc functionality. Although the vehicle is still dri...

  • Page 274

    Turns and bends when driving on a curve with acc engaged, the system may decrease the vehicle speed and acceleration for stabil- ity reasons, with no target vehicle detected. Once the vehicle is out of the curve the system will resume your original set speed. This is a part of normal acc system func...

  • Page 275

    Lane changing acc may not detect a vehicle until it is completely in the lane in which you are traveling. In the illustration shown, acc has not yet detected the vehicle changing lanes and it may not detect the vehicle until it’s too late for the acc system to take action. Acc may not detect a vehic...

  • Page 276

    Stationary objects and vehicles acc does not react to stationary objects and stationary vehicles. For example, acc will not react in situations where the vehicle you are following exits your lane and the vehicle ahead is stopped in your lane. Always be attentive and ready to apply the brakes if nece...

  • Page 277

    To change between the different control modes, push the adaptive cruise control (acc) on/off button which turns the acc and the normal (fixed speed) cruise control off. Pushing the normal (fixed speed) cruise control on/off button will result in turning on (changing to) the normal (fixed speed) crui...

  • Page 278

    Metric speed (km/h) • pushing the set (+) button once will result in a 1 km/h increase in set speed. Each subsequent tap of the button results in an increase of 1 km/h. • if the button is continually pushed, the set speed will continue to increase in 10 km/h increments until the button is released. ...

  • Page 279

    • the braking temperature exceeds normal range (over- heated). • the gear selector is removed from the drive position. • the driver switches esc to full-off mode. To resume speed to resume a previously set speed, push the res button and release. Resume can be used at any speed above 20 mph (32 km/h)...

  • Page 280

    • the automatic braking function may not be applied fast enough for obstacles that move toward the rear of the vehicle from the left and/or right sides. • the automatic braking function can be enabled/ disabled from the customer-programmable features section of the uconnect system. • parksense will ...

  • Page 281

    Parksense warning display the parksense warning screen will only be displayed if sound and display is selected from the customer - pro- grammable features section of the uconnect system. Refer to ⬙ uconnect settings” in “multimedia” for further infor- mation. The parksense warning screen is located ...

  • Page 282

    Single 1/2 second tone slow tone slow tone fast tone 280 starting and operating.

  • Page 283

    Fast tone continuous tone 6 starting and operating 281.

  • Page 284

    The vehicle is close to the obstacle when the warning display shows one flashing arc and sounds a continuous tone. The following chart shows the warning alert opera- tion when the system is detecting an obstacle: warning alerts rear dis- tance (inches/cm) greater than 79 inches (200 cm) 79-59 inches...

  • Page 285

    Adjustable chime volume settings rear chime volume settings can be selected from the customer-programmable features section of the uconnect system, refer to “uconnect settings” in “multimedia” for further information. The chime volume settings include low, medium, and high. The factory default volum...

  • Page 286

    Is clean and clear of snow, ice, mud, dirt or other obstruc- tion and then cycle the ignition. If the message continues to appear, see an authorized dealer. If “parksense unavailable service required” appears in the instrument cluster display, see an autho- rized dealer. Cleaning the parksense syste...

  • Page 287

    Liftgate could provide a false indication that an obstacle is behind the vehicle. Warning! • drivers must be careful when backing up even when using parksense. Always check carefully behind your vehicle, look behind you, and be sure to check for pedestrians, animals, other vehicles, obstructions, an...

  • Page 288

    Note: • the driver can override the automatic braking function by pressing the gas pedal, turning parksense off via parksense switch, or changing the gear while the auto- matic brakes are being applied. • automatic brakes will not be available if esc is not available. • automatic brakes will not be ...

  • Page 289

    The vehicle speed is increased to approximately 7 mph (11 km/h) or above. A display warning will appear in the instrument cluster display indicating the vehicle is above parksense operating speed. The system will become active again if the vehicle speed is decreased to speeds less than approximately...

  • Page 290

    The system will indicate a detected obstacle by showing a single arc in the left and/or right front or rear regions based on the object’s distance and location relative to the vehicle. If an object is detected in the left and/or right rear region, the display will show a single arc in the left and/o...

  • Page 291

    Slow tone for rear only fast tone for rear only fast tone continuous tone 6 starting and operating 289.

  • Page 292

    The vehicle is close to the obstacle when the instrument cluster display shows one flashing arc and sounds a continuous tone. The following chart shows the warning alert operation when the system is detecting an obstacle: warning alerts for rear rear dis- tance (inches/cm) greater than 79 inches (20...

  • Page 293

    Warning alerts for front front distance (inches/cm) greater than 47 inches (120 cm) 47-39 inches (120-100 cm) 39-25 inches (100-65 cm) 25-12 inches (65-30 cm) less than 12 inches (30 cm) audible alert chime none none none fast continuous arcs-left none none none 2nd flashing 1st flashing arcs-center...

  • Page 294

    The “parksense off” message for approximately five seconds. Refer to “instrument cluster display” in “getting to know your instrument panel” for further information. When the gear selector is moved to reverse and the system is disabled, the instrument cluster display will display the “parksense off”...

  • Page 295

    Snow, ice, mud, dirt or other obstruction and then cycle the ignition. If the message continues to appear see your authorized dealer. If the ⬙ parksense unavailable service re- quired ⬙ message appears in the instrument cluster dis- play, see your authorized dealer. Cleaning the parksense system cle...

  • Page 296

    Warning! • drivers must be careful when backing up even when using parksense. Always check carefully behind your vehicle, look behind you, and be sure to check for pedestrians, animals, other vehicles, obstructions, and blind spots before backing up. You are respon- sible for safety and must continu...

  • Page 297

    A parallel or a perpendicular parking space on either side (i.E., driver side or passenger side). Note: • the driver is always responsible for controlling the vehicle, responsible for any surrounding objects, and must intervene as required. • the system is provided to assist the driver and not to su...

  • Page 298

    The parksense active park assist system will turn off automatically for any of the following conditions: • the parking maneuver is completed. • vehicle speed greater than 18 mph (30 km/h) when searching for a parking space. • vehicle speed greater than 5 mph (7 km/h) during active steering guidance ...

  • Page 299

    Parallel parking space assistance operation/ display when the parksense active park assist system is enabled the “active parksense searching - push ok to switch to perpendicular” message will appear in the instrument cluster display. You may switch to perpendicular parking if you desire. Push the ok...

  • Page 300

    When an available parking space has been found, and the vehicle is not in position, you will be instructed to move forward to position the vehicle for a parallel parking sequence. Once the vehicle is in position, you will be instructed to stop the vehicle’s movement and remove your hands from the st...

  • Page 301

    Once the vehicle is at a standstill with your hands removed from the steering wheel, you will be instructed to place the gear selector into the reverse position. When the driver places the gear selector into the reverse position, the system may instruct the driver to wait for steering to complete. S...

  • Page 302

    The system will then instruct the driver to check their surroundings and move backward. Note: • it is the driver’s responsibility to use the brake and accelerator during the semi-automatic parking maneuver. • when the system instructs the driver to remove their hands from the steering wheel, the dri...

  • Page 303

    When the vehicle has reached the end of its backward movement, the system will instruct the driver to check their surroundings and stop the vehicle’s movement. Note: it is the driver’s responsibility to use the brake and stop the vehicle. The driver should check their surround- ings and be prepared ...

  • Page 304

    When the driver places the gear selector into the drive position, the system may instruct the driver to wait for steering to complete. The system will then instruct the driver to check their surroundings and move forward. Check surroundings — wait for steering to complete check surroundings — move f...

  • Page 305

    When the vehicle has reached the end of its forward movement, the system will instruct the driver to check their surroundings and stop the vehicle’s movement. Note: it is the driver’s responsibility to use the brake and stop the vehicle. The driver should check their surround- ings and be prepared t...

  • Page 306

    When the driver places the gear selector into the reverse position, the system may instruct the driver to wait for steering to complete. The system will then instruct the driver to check their surroundings and move backward. Check surroundings — wait for steering to complete check surroundings — mov...

  • Page 307

    Your vehicle is now in the parallel park position. When the maneuver is complete, the driver will be instructed to check the vehicle’s parking position. If the driver is satis- fied with the vehicle position, they should shift to park. The ⬙ active parksense complete - check parking position ⬙ messa...

  • Page 308

    Note: • when searching for a parking space, use the turn signal indicator to select which side of the vehicle you want to perform the parking maneuver. The parksense active park assist system will automatically search for a park- ing space on the passenger’s side of the vehicle if the turn signal is...

  • Page 309

    Once the vehicle is in position, you will be instructed to stop the vehicle’s movement and remove your hands from the steering wheel. Once the vehicle is at a standstill with your hands removed from the steering wheel, you will be instructed to place the gear selector into the reverse position. Spac...

  • Page 310

    When the driver places the gear selector into the reverse position, the system may instruct the driver to wait for steering to complete. The system will then instruct the driver to check their surroundings and move backward. Note: • it is the driver’s responsibility to use the brake and accelerator ...

  • Page 311

    • the parksense active park assist system will allow a maximum of six shifts between drive and reverse. If the maneuver cannot be completed within six shifts, the system will cancel and the instrument cluster display will instruct the driver to complete the maneuver manu- ally. • the system will can...

  • Page 312

    Once the vehicle is in a standstill condition, the driver will be instructed to place the gear selector into the drive position. When the driver places the gear selector into the drive position, the system may instruct the driver to wait for steering to complete. Check surroundings — shift to drive ...

  • Page 313

    The system will then instruct the driver to check their surroundings and move forward. When the vehicle has reached the end of its forward movement, the system will instruct the driver to check their surroundings and stop the vehicle’s movement. Note: it is the driver’s responsibility to use the bra...

  • Page 314

    Once the vehicle is in a standstill condition, the driver will be instructed to place the gear selector into the reverse position. When the driver places the gear selector into the reverse position, the system may instruct the driver to wait for steering to complete. Check surroundings — shift to re...

  • Page 315

    The system will then instruct the driver to check their surroundings and move backward. Your vehicle is now in the perpendicular park position. When the maneuver is complete, the driver will be in- structed to check the vehicle’s parking position. If the driver is satisfied with the vehicle position...

  • Page 316

    Warning! (continued) continue to pay attention to your surroundings. Fail- ure to do so can result in serious injury or death. • before using the parksense active park assist sys- tem, it is strongly recommended that the ball mount and hitch ball assembly is disconnected from the vehicle when the ve...

  • Page 317

    The lanesense system provides a visual warning through the instrument cluster display to prompt the driver to remain within the lane boundaries. The driver may manually override the haptic warning by applying torque into the steering wheel at any time. When only a single lane marking is detected and...

  • Page 318

    To turn the lanesense system off, push the lanesense button once (led turns on). Note: the lanesense system will retain the last system state on or off from the last ignition cycle when the ignition is changed to the on/run position. Lanesense warning message the lanesense system will indicate the c...

  • Page 319

    • when the lanesense system senses the lane has been approached and is in a lane departure situation, the left thick lane line flashes yellow (on/off), the left thin line remains solid yellow and the lanesense telltale changes from solid white to flashing yellow. Note: the lanesense system operates ...

  • Page 320

    The lanesense telltale changes from solid green to solid yellow. At this time torque is applied to the steering wheel in the opposite direction of the lane boundary. • for example: if approaching the left side of the lane the steering wheel will turn to the right. • when the lanesense system senses ...

  • Page 321

    Changing lanesense status the lanesense system has settings to adjust the intensity of the torque warning and the warning zone sensitivity (early/late) that you can configure through the uconnect system screen. Refer to “uconnect settings” in “multime- dia” for further information. Note: • when enab...

  • Page 322

    Rear of the vehicle. The following table shows the approxi- mate distances for each zone: zone distance to the rear of the vehicle red 0 - 1 ft (0 - 30 cm) yellow 1 ft - 6.5 ft (30 cm - 2 m) green 6.5 ft or greater (2 m or greater) warning! Drivers must be careful when backing up even when using the...

  • Page 323

    Rear camera — viewing at speed when the vehicle is in park, neutral or drive, the rear view camera can be activated with the “rear view camera” button in the controls menu. This feature allows the customer to monitor the area directly behind the vehicle (or trailer, if equipped) for up to ten second...

  • Page 324

    Note: in certain cold conditions, ice may prevent the fuel door from opening. If this occurs, lightly push on the fuel door to break the ice buildup and re-release the fuel door using the inside release button. Do not pry on the door. 3. There is no fuel filler cap. Two flapper doors inside the pipe...

  • Page 325

    Warning! (continued) • never add fuel when the engine is running. This is in violation of most state and federal fire regulations and may cause the “malfunction indicator light” to turn on. • a fire may result if fuel is pumped into a portable container that is inside of a vehicle. You could be burn...

  • Page 326

    Vehicle loading certification label as required by national highway traffic safety adminis- tration regulations, your vehicle has a certification label affixed to the driver’s side door or pillar. This label contains the month and year of manufacture, gross vehicle weight rating (gvwr), gross axle w...

  • Page 327

    Curb weight the curb weight of a vehicle is defined as the total weight of the vehicle with all fluids, including vehicle fuel, at full capacity conditions, and with no occupants or cargo loaded into the vehicle. The front and rear curb weight values are determined by weighing your vehicle on a comm...

  • Page 328

    Common towing definitions the following trailer towing related definitions will assist you in understanding the following information: gross vehicle weight rating (gvwr) the gvwr is the total allowable weight of your vehicle. This includes driver, passengers, cargo and tongue weight. The total load ...

  • Page 329

    Trailer sway control the trailer sway control can be a mechanical telescoping link that can be installed between the hitch receiver and the trailer tongue that typically provides adjustable friction associated with the telescoping motion to dampen any unwanted trailer swaying motions while traveling...

  • Page 330

    Trailer hitch classification the following chart provides the industry standard for the maximum trailer weight a given trailer hitch class can tow and should be used to assist you in selecting the correct trailer hitch for your intended towing condition. Trailer hitch classification definitions clas...

  • Page 331

    Note: • the trailer tongue weight must be considered as part of the combined weight of occupants and cargo, and should never exceed the weight referenced on the tire and loading information placard. Refer to “tires” in “servicing and maintenance” for further information. • the manufacturer does not ...

  • Page 332

    2. Pull the bottom of the cover outward (towards you). 3. Lower back down to disengage the tabs located at the top of the hitch receiver cover and then pull outwards to remove. To reinstall the hitch receiver cover after towing repeat the procedure in reverse order. Note: be sure to engage all tabs ...

  • Page 333

    Trailer and tongue weight never exceed the maximum tongue weight stamped on your bumper or trailer hitch. Consider the following items when computing the weight on the rear axle of the vehicle: • the tongue weight of the trailer. • the weight of any other type of cargo or equipment put in or on your...

  • Page 334

    Maintenance” for the proper maintenance intervals. When towing a trailer, never exceed the gawr or gcwr ratings. Warning! Improper towing can lead to a collision. Follow these guidelines to make your trailer towing as safe as possible: • make certain that the load is secured in the trailer and will ...

  • Page 335

    Towing requirements — tires • do not attempt to tow a trailer while using a compact spare tire. • proper tire inflation pressures are essential to the safe and satisfactory operation of your vehicle. Refer to “tires” in “servicing and maintenance” for proper tire inflation procedures. • check the tr...

  • Page 336

    Caution! (continued) be of adequate capacity. Failure to do this could lead to accelerated brake lining wear, higher brake pedal effort, and longer stopping distances. Towing requirements — trailer lights and wiring whenever you pull a trailer, regardless of the trailer size, stoplights and turn sig...

  • Page 337

    Towing tips before setting out on a trip, practice turning, stopping, and backing up the trailer in an area located away from heavy traffic. Automatic transmission select the drive range when towing. The transmission controls include a drive strategy to avoid frequent shifting when towing. However, ...

  • Page 338

    • to prevent excess heat generation, avoid continuous driving at high rpm. Reduce vehicle speed as necessary to avoid extended driving at high rpm. Return to a higher gear or vehicle speed when grade and road conditions allow. Speed control — if equipped • do not use on hilly terrain or with heavy l...

  • Page 339

    Warning! Rapid acceleration on slippery surfaces is dangerous. Unequal traction can cause sudden pulling of the front wheels. You could lose control of the vehicle and possibly have a collision. Accelerate slowly and care- fully whenever there is likely to be poor traction (ice, snow, wet, mud, loos...

  • Page 340

    Shallow standing water although your vehicle is capable of driving through shal- low standing water, consider the following cautions and warnings before doing so. Warning! • driving through standing water limits your vehicle’s traction capabilities. Do not exceed 5 mph (8 km/h) when driving through ...

  • Page 341

    In case of emergency contents 䡵 hazard warning flashers . . . . . . . . . . . .340 䡵 assist and sos mirror — if equipped . . . .340 䡵 bulb replacement . . . . . . . . . . . . . . . . . . . .345 ▫ replacement bulbs . . . . . . . . . . . . . . . . . . . . .345 ▫ bulb replacement . . . . . . . . . . . ...

  • Page 342

    Hazard warning flashers the hazard warning flasher switch is located on the switch bank just above the climate controls. Push the switch to turn on the hazard warning flasher. When the switch is activated, all direc- tional turn signals will flash on and off to warn oncoming traffic of an emergency....

  • Page 343

    Warning! (continued) related to the use of the features and applications in this vehicle. Only use the features and applications when it is safe to do so. Failure to do so may result in an accident involving serious injury or death. Note: • your vehicle may be transmitting data as authorized by the ...

  • Page 344

    4. You should be able to speak with the sos operator through the vehicle audio system to determine if addi- tional help is needed. Warning! Always obey traffic laws and pay attention to the road. Always drive safely with your hands on the steering wheel. You have full responsibility and assume all r...

  • Page 345

    Warning! (continued) initiate an emergency call. To avoid interference that can cause the sos call system to fail, never add aftermarket equipment (e.G., two-way mobile radio, cb radio, data recorder, etc.) to your vehicle’s electri- cal system or modify the antennas on your vehicle. If your vehicle...

  • Page 346

    Even if the sos call system is fully functional, factors beyond fca us llc’s control may prevent or stop the sos call system operation. These include, but are not limited to, the following factors: • delayed accessories mode is active. • the ignition is in the off position. • the vehicle’s electrica...

  • Page 347

    This device may not cause harmful interference, and (2) this device must accept any interference received, includ- ing interference that may cause undesired operation. Note: changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to ope...

  • Page 348

    Exterior bulbs bulb number premium headlamps (low/high beam) d3s (serviced at authorized dealer) premium park/turn signal lamp led - (service at authorized dealer) premium daytime running lamp (drl) led - (service at authorized dealer) premium front fog lamps led - (service at authorized dealer) pre...

  • Page 349

    Bulb replacement high intensity discharge headlamps (hid) — if equipped the headlamps are a type of high voltage discharge tube. High voltage can remain in the circuit even with the headlamp switch off and the key removed. Because of this, you should not attempt to service a headlamp bulb yourself. ...

  • Page 350

    3. Grasp the tail lamp and pull firmly rearward to disen- gage the lamp from the aperture panel. 4. Twist socket counter clockwise and remove from lamp. 5. Pull the bulb to remove it from the socket. 6. Replace the bulb, reinstall the socket, and reattach the lamp assembly. Rear liftgate mounted tai...

  • Page 351

    3. Continue removing the trim. 4. Disconnect the two trim panel lights. 5. Tail lamps are now visible. Rotate socket(s) counter clockwise. 6. Remove/replace bulb(s). 7. Reinstall the socket(s). 8. Reverse process to reinstall the liftgate trim. Liftgate lower trim rear of liftgate tail lamp 1 — auxi...

  • Page 352

    Center high-mounted stop lamp (chmsl) the center high mounted stop lamp is an led. Service at an authorized dealer. Rear license lamp the rear license lamps are leds. See your authorized dealer for service. Fuses warning! • when replacing a blown fuse, always use an appro- priate replacement fuse wi...

  • Page 353

    General information the fuses protect electrical systems against excessive current. When a device does not work, you must check the fuse element inside the blade fuse for a break/melt. Also, please be aware that when using power outlets for extended periods of time with the engine off may result in ...

  • Page 354

    Cavity cartridge fuse micro fuse description f03 60 amp yellow – radiator fan f05 40 amp green – compressor for air suspension — if equipped f06 40 amp green – anti-lock brakes/electronic stability control pump f07 30 amp pink – starter solenoid f09 30 amp pink – diesel fuel heater (diesel engine on...

  • Page 355

    Cavity cartridge fuse micro fuse description f28 20 amp blue – trailer tow backup lights — if equipped f29 20 amp blue – trailer tow parking lights — if equipped f30 30 amp pink – trailer tow receptacle — if equipped f32 30 amp pink – drive train control module f34 30 amp pink – slip differential co...

  • Page 356

    Cavity cartridge fuse micro fuse description f56 – 15 amp blue additional content (diesel engine only) f57 – 20 amp yellow nox sensor f58 – 15 amp blue hid headlamps lh — if equipped f59 – 10 amp red purging pump (diesel engine only) f60 – 15 amp blue transmission control module f61 – 10 amp red tra...

  • Page 357

    Cavity cartridge fuse micro fuse description f77 – 10 amp red drivetrain control module/front axle disconnect module f78 – 10 amp red engine control module/electric power steering f80 – 10 amp red universal garage door opener/compass/anti-intrusion module f81 – 20 amp yellow trailer tow right turn/s...

  • Page 358

    Cavity cartridge fuse micro fuse description f97 – 20 amp yellow rear heated seats & heated steering wheel — if equipped f98 – 20 amp yellow front heated seats — if equipped f99 – 10 amp red climate control/driver assistance systems module/ dsrc f100 – 10 amp red active damping — if equipped f101 – ...

  • Page 359

    Jacking and tire changing warning! • do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel. • being under a jacked-up vehicle is dangerous. The vehicle could slip...

  • Page 360

    Jack location the scissor-type jack and tire changing tools are located in the rear cargo area, below the load floor. Note: the funnel for the cap-less fuel system is located on top of the spare tire. If your vehicle is out of fuel and an auxiliary fuel can is needed, insert the funnel into the fill...

  • Page 361

    5. Turn the ignition off. 6. Block both the front and rear of the wheel diagonally opposite the jacking position. For example, if the right front wheel is being changed, block the left rear wheel. Note: passengers should not remain in the vehicle when the vehicle is being jacked. 7. For vehicles equ...

  • Page 362

    Caution! Do not attempt to raise the vehicle by jacking on locations other than those indicated in the jacking instructions for this vehicle. 1. Remove the spare tire, jack, and tools from storage. 2. Loosen (but do not remove) the wheel lug nuts by turning them to the left, one turn, while the whee...

  • Page 363

    4. For the front axle, place the jack on the body flange just behind the front tire as indicated by the triangular lift point symbol on the sill molding. Do not raise the vehicle until you are sure the jack is fully engaged. 5. For a rear tire, place the jack in the slot on the rear tie-down bracket...

  • Page 364

    Caution! Do not raise the vehicle by the body side sill mold- ing. Be sure the jack is placed in the proper engage- ment location on the inside of the panel. Damage of the vehicle may occur if the procedure is not properly followed. 6. Raise the vehicle by turning the jack screw clockwise. Raise the...

  • Page 365

    8. Position the spare wheel/tire on the vehicle and install the lug nuts with the cone-shaped end toward the wheel. Lightly tighten the nuts. Caution! Be sure to mount the spare tire with the valve stem facing outward. The vehicle could be damaged if the inflatable spare tire is mounted incorrectly....

  • Page 366

    13. Have the aluminum road wheel and tire repaired as soon as possible, properly secure the spare tire with the special wing nut torqued to 3.7 ft-lbs (5 n·m), reinstall the jack and tool kit foam tray, and latch the rear load floor cover. Note: do not drive with the spare tire installed for more th...

  • Page 367

    5. After 25 miles (40 km), check the lug nut torque with a torque wrench to ensure that all lug nuts are properly seated against the wheel. Jump starting if your vehicle has a discharged battery, it can be jump started using a set of jumper cables and a battery in another vehicle, or by using a port...

  • Page 368

    Warning! • take care to avoid the radiator cooling fan whenever the hood is raised. It can start anytime the ignition switch is on. You can be injured by moving fan blades. • remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact. You coul...

  • Page 369

    Connecting the jumper cables 1. Connect the positive (+) end of the jumper cable to the remote positive (+) post of the discharged vehicle. 2. Connect the opposite end of the positive (+) jumper cable to the positive (+) post of the booster battery. 3. Connect the negative end (-) of the jumper cabl...

  • Page 370

    If frequent jump starting is required to start your vehicle you should have the battery and charging system tested at an authorized dealer. Caution! Accessories plugged into the vehicle power outlets draw power from the vehicle’s battery, even when not in use (i.E., cellular devices, etc.). Eventual...

  • Page 371

    Warning! (continued) see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool. Never try to open a cooling system pressure cap when the radiator or coolant bottle is hot. Caution! Driving with a hot cooling system could damage your vehicle. If the te...

  • Page 372

    3. Press and maintain firm pressure on the brake pedal. 4. Using a screwdriver or similar tool, push the metal latch in towards the tether strap. 5. While the metal latch is in the open position, simulta- neously pull upwards on the tether strap until the lever clicks and latches in the released pos...

  • Page 373

    Caution! Closing the armrest while the manual park release is activated may damage the manual park release mechanism, the transmission, and/or the armrest. Note: to prevent the vehicle from rolling unintentionally, firmly apply the parking brake. To disengage the manual park release lever: 1. To dis...

  • Page 374

    Note: be sure to replace the cover by snapping it back in place. Freeing a stuck vehicle if your vehicle becomes stuck in mud, sand or snow, it can often be moved using a rocking motion. Turn the steering wheel right and left to clear the area around the front wheels. Push and hold the lock button o...

  • Page 375

    Warning! (continued) seconds continuously without stopping when you are stuck and do not let anyone near a spinning wheel, no matter what the speed. Caution! • racing the engine or spinning the wheels may lead to transmission overheating and failure. Allow the engine to idle with the transmission in...

  • Page 376

    Enhanced accident response system (ears) this vehicle is equipped with an enhanced accident response system. Please refer to “occupant restraint systems” in “safety” for further information on the enhanced accident re- sponse system (ears) function. Event data recorder (edr) this vehicle is equipped...

  • Page 377

    Servicing and maintenance contents 䡵 scheduled servicing — srt . . . . . . . . . . . .377 ▫ maintenance plan. . . . . . . . . . . . . . . . . . . . . . .378 䡵 engine compartment . . . . . . . . . . . . . . . . .381 ▫ 6.2l supercharged engine . . . . . . . . . . . . . . . .381 ▫ 6.4l engine . . . . ....

  • Page 378

    ▫ wheel and wheel trim care . . . . . . . . . . . . . .431 ▫ tire chains (traction devices) . . . . . . . . . . . . .432 ▫ tire rotation recommendations . . . . . . . . . . . .433 䡵 department of transportation uniform tire quality grades . . . . . . . . . .434 ▫ treadwear . . . . . . . . . . . . . ...

  • Page 379

    Scheduled servicing — srt the scheduled maintenance services listed in this manual must be done at the times or mileages specified to protect your vehicle warranty and ensure the best vehicle perfor- mance and reliability. More frequent maintenance may be needed for vehicles in severe operating cond...

  • Page 380

    • check all lights and other electrical items for correct operation. At each oil change • change the engine oil filter. • inspect the brake hoses and lines. Caution! Failure to perform the required maintenance items may result in damage to the vehicle. Maintenance plan miles: 6,000 12,000 18,000 24,...

  • Page 381

    Miles: 6,000 12,000 18,000 24,000 30,000 36,000 42,000 48,000 54,000 60,000 66,000 72,000 78,000 84,000 90,000 96,000 102,000 108,000 1 14,000 120,000 126,000 132,000 138,000 144,000 150,000 or months: 6 12 18 24 30 36 42 48 54 60 66 72 78 84 90 96 102 108 114 120 126 132 138 144 150 or kilometers: ...

  • Page 382

    Miles: 6,000 12,000 18,000 24,000 30,000 36,000 42,000 48,000 54,000 60,000 66,000 72,000 78,000 84,000 90,000 96,000 102,000 108,000 1 14,000 120,000 126,000 132,000 138,000 144,000 150,000 or months: 6 12 18 24 30 36 42 48 54 60 66 72 78 84 90 96 102 108 114 120 126 132 138 144 150 or kilometers: ...

  • Page 383

    Engine compartment 6.2l supercharged engine 1 — remote jump start positive terminal 7 — washer fluid reservoir 2 — power distribution center (fuses) 8 — engine oil dipstick 3 — intercooler coolant reservoir 9 — coolant pressure cap (radiator) 4 — engine oil fill 10 — engine coolant reservoir 5 — bra...

  • Page 384

    6.4l engine 1 — remote jump start positive terminal 6 — air cleaner filter 2 — power distribution center (fuses) 7 — washer fluid reservoir 3 — engine oil dipstick 8 — coolant pressure cap (radiator) 4 — engine oil fill 9 — engine coolant reservoir 5 — brake fluid reservoir 10 — remote jump start ne...

  • Page 385

    Checking oil level to assure proper lubrication of your vehicle’s engine, the engine oil must be maintained at the correct level. Check the oil level at regular intervals, such as every fuel stop. The best time to check the engine oil level is about five minutes after a fully warmed up engine is shu...

  • Page 386

    Warning! • battery fluid is a corrosive acid solution and can burn or even blind you. Do not allow battery fluid to contact your eyes, skin, or clothing. Do not lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area immediately with large amounts of water. Ref...

  • Page 387

    Warning! You can be badly injured working on or around a motor vehicle. Only do service work for which you have the knowledge and the proper equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic. Engine oil change engine oil the oil c...

  • Page 388

    American petroleum institute (api) engine oil identification symbol this symbol means that the oil has been certified by the american pe- troleum institute (api). The manu- facturer only recommends api cer- tified engine oils. This symbol certifies 0w-20, 5w-20, 0w-30, 5w-30 and 10w-30 engine oils. ...

  • Page 389

    Engine oil filter the engine oil filter should be replaced with a new filter at every engine oil change. Engine oil filter selection this manufacturer’s engines have a full-flow type dispos- able oil filter. Use a filter of this type for replacement. The quality of replacement filters varies conside...

  • Page 390

    Engine air cleaner filter removal 1. Release the spring clips from the air cleaner cover. 2. Lift the air cleaner cover to access the air cleaner filter. Air cleaner filter cover 1 — clean air hose clamp 2 — air hose 3 — spring clips open air cleaner filter assembly 1 — air cleaner cover 2 — air cle...

  • Page 391

    3. Remove the air cleaner filter element from the housing assembly. Engine air cleaner filter installation note: inspect and clean the housing if dirt or debris is present before replacing the air filter element. 1. Install the air cleaner filter element into the housing assembly with the air cleane...

  • Page 392

    Engine air cleaner filter removal 1. Loosen the fasteners on the air cleaner filter cover. 2. Lift the air filter cleaner cover to access the air cleaner filter. Air cleaner filter assembly 1 — clean air hose clamp 2 — fasteners open air cleaner filter assembly 1 — air cleaner cover 2 — air cleaner ...

  • Page 393

    3. Remove the air cleaner filter element from the housing assembly. Engine air cleaner filter installation note: inspect and clean the housing if dirt or debris is present before replacing the air filter element. 1. Install the air cleaner filter element into the housing assembly with the air cleane...

  • Page 394

    However, cracks running along a rib (not across) are not normal. Any belt with cracks running along a rib must be replaced. Also have the belt replaced if it has excessive wear, frayed cords or severe glazing. Conditions that would require replacement: • rib chunking (one or more ribs has separated ...

  • Page 395

    Warning! • use only refrigerants and compressor lubricants ap- proved by the manufacturer for your air conditioning system. Some unapproved refrigerants are flam- mable and can explode, injuring you. Other unap- proved refrigerants or lubricants can cause the sys- tem to fail, requiring costly repai...

  • Page 396

    Air conditioning filter replacement (a/c air filter) refer to “scheduled servicing” in this section for the proper maintenance intervals. Warning! Do not remove the cabin air filter while the vehicle is running, or while the ignition is in the acc or on/ run mode. With the cabin air filter removed a...

  • Page 397

    Note: when disengaging the glove compartment door from its hinges, there will be some resistance. 4. With the glove compartment door loose, remove the glove compartment tension tether and tether clip by sliding the clip toward the face of the glove compart- ment door and lifting the clip out of glov...

  • Page 398

    7. Install the a/c air filter with the arrow on the filter pointing toward the floor. When installing the filter cover, make sure the retaining tabs fully engage the cover. Caution! The cabin air filter is identified with an arrow to indicate airflow direction through the filter. Failure to properly...

  • Page 399

    Avoid using the wiper blades to remove frost or ice from the windshield. Keep the blade rubber out of contact with petroleum products such as engine oil, gasoline, etc. Note: life expectancy of wiper blades varies depending on geographical area and frequency of use. Poor perfor- mance of blades may ...

  • Page 400

    2. To disengage the wiper blade from the wiper arm, flip up the release tab on the wiper blade and while holding the wiper arm with one hand, slide the wiper blade down towards the base of the wiper arm. 3. With the wiper blade disengaged, remove the wiper blade from the wiper arm by holding the wip...

  • Page 401

    2. Position the wiper blade near the hook on the tip of the wiper arm with the wiper release tab open and the blade side of the wiper facing up and away from the wind- shield. 3. Insert the hook on the tip of the arm through the opening in the wiper blade under the release tab. 4. Slide the wiper bl...

  • Page 402

    3. To remove the wiper blade from the wiper arm, grasp the bottom end of the wiper blade nearest to wiper arm with your right hand. With your left hand hold the wiper arm as you pull the wiper blade away from the wiper arm past its stop far enough to unsnap the wiper blade pivot pin from the recepta...

  • Page 403

    Installing the rear wiper 1. Lift the rear wiper arm pivot cap away from the glass to allow the rear wiper blade to be raised off of the glass. Note: the rear wiper arm cannot be fully raised off the glass unless the wiper arm pivot cap is unsnapped first. Attempting to fully raise the rear wiper ar...

  • Page 404

    Caution! • the catalytic converter requires the use of unleaded fuel only. Leaded gasoline will destroy the effective- ness of the catalyst as an emissions control device and may seriously reduce engine performance and cause serious damage to the engine. • damage to the catalytic converter can resul...

  • Page 405

    Cooling system warning! • turn vehicle off and disconnect the fan motor lead before working near the radiator cooling fan. • you or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator. If you see or hear steam coming from under the hood, do not open the hood unt...

  • Page 406

    Cooling system — drain, flush and refill note: some vehicles require special tools to add coolant properly. Failure to fill these systems properly could lead to severe internal engine damage. If any coolant is needed to be added to the system please contact your local autho- rized dealer. If the eng...

  • Page 407

    Adding coolant your vehicle has been built with an improved engine coolant (oat coolant conforming to ms.90032) that allows extended maintenance intervals. This engine coolant (anti- freeze) can be used up to ten years or 150,000 miles (240,000 km) before replacement. To prevent reducing this extend...

  • Page 408

    Cooling system pressure cap the cap must be fully tightened to prevent loss of engine coolant (antifreeze), and to ensure that engine coolant (antifreeze) will return to the radiator from the coolant expansion bottle/recovery tank if so equipped. The cap should be inspected and cleaned if there is a...

  • Page 409

    Points to remember note: when the vehicle is stopped after a few miles/ kilometers of operation, you may observe vapor coming from the front of the engine compartment. This is normally a result of moisture from rain, snow, or high humidity accumulating on the radiator and being vaporized when the th...

  • Page 410

    Fluid level check — brake master cylinder the fluid level of the master cylinder should be checked whenever the vehicle is serviced, or immediately if the brake system warning light is on. If necessary, add fluid to bring level within the designated marks on the side of the reservoir of the brake ma...

  • Page 411

    Automatic transmission selection of lubricant it is important to use the proper transmission fluid to ensure optimum transmission performance and life. Use only the manufacturer’s specified transmission fluid. Refer to “fluids and lubricants” in “technical specifications” for fluid specifications. I...

  • Page 412

    Fluid level checked. Operating the vehicle with an im- proper fluid level can cause severe transmission damage. Caution! If a transmission fluid leak occurs, visit an authorized dealer immediately. Severe transmission damage may occur. An authorized dealer has the proper tools to adjust the fluid le...

  • Page 413

    Caution! Do not overtighten the plugs as it could damage them and cause them to leak. Selection of lubricant use only the manufacturer’s recommended fluid. Refer to “fluids and lubricants” in “technical specifications” for further information. Transfer case fluid level check for normal service, peri...

  • Page 414

    Tire markings note: • p (passenger) — metric tire sizing is based on u.S. Design standards. P-metric tires have the letter “p” molded into the sidewall preceding the size designation. Example: p215/65r15 95h. • european — metric tire sizing is based on european design standards. Tires designed to th...

  • Page 415

    Tire sizing chart example: example size designation: p215/65r15xl 95h, 215/65r15 96h, lt235/85r16c, t145/80d18 103m, 31x10.5 r15 lt p = passenger car tire size based on u.S. Design standards, or ⴖ ....Blank.... ⴖ = passenger car tire based on european design standards, or lt = light truck tire based...

  • Page 416

    Example: h = speed symbol – a symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under cer- tain operating conditions – the maximum speed corresponding to the speed symbol should only be achieved under specified operating condi- tions (i.E., tire p...

  • Page 417

    Tire identification number (tin) the tin may be found on one or both sides of the tire; however, the date code may only be on one side. Tires with white sidewalls will have the full tin, including the date code, located on the white sidewall side of the tire. Look for the tin on the outboard side of...

  • Page 418

    Tire terminology and definitions term definition b-pillar the vehicle b-pillar is the structural member of the body located be- hind the front door. Cold tire inflation pressure cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least three hour...

  • Page 419

    Tire loading and tire pressure note: the proper cold tire inflation pressure is listed on the driver’s side b-pillar or the rear edge of the driver’s side door. Check the inflation pressure of each tire, including the spare tire (if equipped), at least monthly and inflate to the recommended pressure...

  • Page 420

    Tire and loading information placard this placard tells you important information about the: 1. Number of people that can be carried in the vehicle. 2. Total weight your vehicle can carry. 3. Tire size designed for your vehicle. 4. Cold tire inflation pressures for the front, rear, and spare tires. ...

  • Page 421

    Steps for determining correct load limit— (1) locate the statement “the combined weight of occupants and cargo should never exceed xxx kg or xxx lbs.” on your vehicle’s placard. (2) determine the combined weight of the driver and passengers that will be riding in your vehicle. (3) subtract the combi...

  • Page 422

    Warning! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the rec- ommended load capacity for your vehicle. Never over- load them. 420 servicing and maintenance.

  • Page 423

    Tires — general information tire pressure proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle. Four primary areas are affected by improper tire pressure: • safety and vehicle stability • economy • tread wear • ride comfort safety warning! • improperly i...

  • Page 424

    Tread wear improper cold tire inflation pressures can cause abnormal wear patterns and reduced tread life, resulting in the need for earlier tire replacement. Ride comfort and vehicle stability proper tire inflation contributes to a comfortable ride. Over-inflation produces a jarring and uncomfortab...

  • Page 425

    Pressure should be increased by 3 psi (21 kpa), which equals 1 psi (7 kpa) for every 12°f (7°c) for this outside temperature condition. Tire pressure may increase from 2 to 6 psi (13 to 40 kpa) during operation. Do not reduce this normal pressure build up or your tire pressure will be too low. Tire ...

  • Page 426

    Run flat tires — if equipped run flat tires allow you the capability to drive 50 miles (80 km) at 50 mph (80 km/h) after a rapid loss of inflation pressure. This rapid loss of inflation is referred to as the run flat mode. A run flat mode occurs when the tire inflation pressure is of/or below 14 psi...

  • Page 427

    Tread wear indicators tread wear indicators are in the original equipment tires to help you in determining when your tires should be re- placed. These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth becomes a 1/16 of an inch (1.6 mm). When t...

  • Page 428

    Warning! (continued) you could lose control and have a collision resulting in serious injury or death. Keep dismounted tires in a cool, dry place with as little exposure to light as possible. Protect tires from contact with oil, grease, and gasoline. Replacement tires the tires on your new vehicle p...

  • Page 429

    Warning! (continued) • never use a tire with a smaller load index or capacity, other than what was originally equipped on your vehicle. Using a tire with a smaller load index could result in tire overloading and failure. You could lose control and have a collision. • failure to equip your vehicle wi...

  • Page 430

    Snow tires some areas of the country require the use of snow tires during the winter. Snow tires can be identified by a “mountain/snowflake” symbol on the tire sidewall. If you need snow tires, select tires equivalent in size and type to the origi- nal equipment tires. Use snow tires only in sets of...

  • Page 431

    Spare by looking at the spare tire description on the tire and loading information placard located on the driver’s side door opening or on the sidewall of the tire. Compact spare tire descriptions begin with the letter “t” or “s” preceding the size designation. Example: t145/80d18 103m. T, s = tempo...

  • Page 432

    Warning! Compact and collapsible spares are for temporary emergency use only. With these spares, do not drive more than 50 mph (80 km/h). Temporary use spares have limited tread life. When the tread is worn to the tread wear indicators, the temporary use spare tire needs to be replaced. Be sure to f...

  • Page 433

    Wheel and wheel trim care all wheels and wheel trim, especially aluminum and chrome plated wheels, should be cleaned regularly using mild (neutral ph) soap and water to maintain their luster and to prevent corrosion. Wash wheels with the same soap solution recommended for the body of the vehicle. Yo...

  • Page 434

    Dark vapor chrome, black satin chrome, or low gloss clear coat wheels caution! If your vehicle is equipped with these specialty wheels, do not use wheel cleaners, abrasives, or polishing compounds. They will permanently damage this finish and such damage is not covered by the new vehicle limited war...

  • Page 435

    Caution! (continued) • observe the traction device manufacturer’s instruc- tions on the method of installation, operating speed, and conditions for use. Always use the suggested operating speed of the device manufacturer’s if it is less than 30 mph (48 km/h). • do not use traction devices on a compa...

  • Page 436

    Department of transportation uniform tire quality grades the following tire grading categories were established by the national highway traffic safety administration. The specific grade rating assigned by the tire’s manu- facturer in each category is shown on the sidewall of the tires on your vehicl...

  • Page 437

    Represent higher levels of performance on the laboratory test wheel, than the minimum required by law. Warning! The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, under-inflation, or excessive load- ing, either separately or i...

  • Page 438

    • salt in the air near seacoast localities. • atmospheric fallout/industrial pollutants. Body and underbody maintenance cleaning headlights your vehicle is equipped with plastic headlights and fog lights that are lighter and less susceptible to stone breakage than glass headlights. Plastic is not as...

  • Page 439

    • if you detect any stone chips or scratches in the paint, touch them up immediately. The cost of such repairs is considered the responsibility of the owner. • if your vehicle is damaged due to a collision or similar cause that destroys the paint and protective coating, have your vehicle repaired as...

  • Page 440

    Warning! (continued) must be replaced after a collision if they have been damaged (i.E., bent retractor, torn webbing, etc.). Plastic and coated parts use mopar total clean to clean vinyl upholstery. Caution! • direct contact of air fresheners, insect repellents, suntan lotions, or hand sanitizers t...

  • Page 441

    Caution! Do not use alcohol and alcohol-based and/or ketone based cleaning products to clean leather seats, as damage to the seat may result. Glass surfaces all glass surfaces should be cleaned on a regular basis with mopar glass cleaner, or any commercial household-type glass cleaner. Never use an ...

  • Page 443

    Technical specifications contents 䡵 identification data. . . . . . . . . . . . . . . . . . .442 ▫ vehicle identification number . . . . . . . . . . . . .442 䡵 brake system . . . . . . . . . . . . . . . . . . . . . . . .442 䡵 wheel and tire torque specifications . .443 ▫ torque specifications . . . ....

  • Page 444

    Identification data vehicle identification number the vehicle identification number (vin) is found on a label located on the left front corner of the instrument panel pad, visible from outside of the vehicle through the wind- shield. This number also is stamped on the right front floor, behind the r...

  • Page 445

    In the event power assist is lost for any reason (i.E., repeated brake applications with the engine off) the brakes will still function. However, the effort required to brake the vehicle will be much greater than that required with the power system operating. Note: due to the performance nature of o...

  • Page 446

    Warning! To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts fully until the vehicle has been lowered. Failure to follow this warning may result in personal injury. Fuel requirements 6.2l supercharged and 6.4l engine do not use e-85 flex fuel or ethanol blends greater ...

  • Page 447

    Poor quality gasoline can cause problems such as hard starting, stalling, and hesitations. If you experience these symptoms, try another brand of gasoline before consider- ing service for the vehicle. Reformulated gasoline many areas of the country require the use of cleaner burning gasoline referre...

  • Page 448

    Caution! (continued) cause emissions to exceed the applicable standard, and/or cause the “malfunction indicator light” to illuminate. Please observe pump labels as they should clearly communicate if a fuel contains greater than 15% ethanol (e-15). Problems that result from using gasoline containing ...

  • Page 449

    Fuel system cautions caution! Follow these guidelines to maintain your vehicle’s performance: • the use of leaded gasoline is prohibited by federal law. Using leaded gasoline can impair engine perfor- mance and damage the emissions control system. • an out-of-tune engine or certain fuel or ignition ...

  • Page 450

    Fluid capacities u.S. Metric fuel (approximate) 24.6 gallons 93.1 liters engine oil with filter 6.2 liter engine (sae 0w-40, synthetic api certified, ms-12633) 8.3 quarts 7.8 liters 6.4 liter engine (sae 0w-40, synthetic api certified, ms-12633) 7 quarts 6.6 liters cooling system* 6.2l engine (mopar...

  • Page 451

    Fluids and lubricants engine component fluid, lubricant or genuine part engine/intercooler coolant we recommend you use mopar antifreeze/coolant 10 year/150,000 mile formula oat (organic additive tech- nology) that meets the requirements of fca material standard ms.90032. Engine oil for best perform...

  • Page 452

    Chassis component fluid, lubricant, or genuine part automatic transmission use only mopar zf 8&9 speed atf automatic transmis- sion fluid or equivalent. Failure to use the correct fluid may affect the function or performance of your transmis- sion. Transfer case – single-speed (selec-track) we recom...

  • Page 453

    Multimedia contents 䡵 uconnect radios . . . . . . . . . . . . . . . . . . . .454 䡵 personalized menu bar . . . . . . . . . . . . . . .454 䡵 cybersecurity . . . . . . . . . . . . . . . . . . . . . . . .455 䡵 uconnect settings . . . . . . . . . . . . . . . . . . .456 ▫ customer programmable features —...

  • Page 454

    ▫ cd player . . . . . . . . . . . . . . . . . . . . . . . . . . . .498 䡵 ipod/usb/mp3 control — if equipped . . .498 䡵 uconnect rear seat entertainment (rse) system — if equipped . . . . . . . . . . . . .499 ▫ getting started . . . . . . . . . . . . . . . . . . . . . . . .499 ▫ dual video screen . ....

  • Page 455

    ▫ siriusxm travel link (4c/4c nav). . . . . . . . . .525 ▫ apple carplay — if equipped. . . . . . . . . . . . . .526 ▫ android auto — if equipped . . . . . . . . . . . . . .527 ▫ general information . . . . . . . . . . . . . . . . . . . . .529 ▫ additional information . . . . . . . . . . . . . . . ....

  • Page 456

    Uconnect radios for detailed information about your uconnect radio, refer to your uconnect owner’s manual supplement. Note: uconnect screen images are for illustration pur- poses only and may not reflect exact software for your vehicle. Personalized menu bar the uconnect features and services in the...

  • Page 457

    Cybersecurity your vehicle may be a connected vehicle and may be equipped with both wired and wireless networks. These networks allow your vehicle to send and receive informa- tion. This information allows systems and features in your vehicle to function properly. Your vehicle may be equipped with c...

  • Page 458

    Note: • fca us llc or your dealer may contact you directly regarding software updates. • to help further improve vehicle security and minimize the potential risk of a security breach, vehicle owners should: • routinely check www.Driveuconnect.Com/software- update to learn about available uconnect so...

  • Page 459

    Customer programmable features — uconnect 4c/4c nav settings press the “apps ” button, then press the “settings” button on the touchscreen to display the menu setting screen. In this mode the uconnect system allows you to access programmable features that may be equipped such as display, units, voic...

  • Page 460

    Setting name selectable options display brightness with headlights off + - note: to make changes to the ⬙ display brightness with headlights off ⬙ setting, the headlights must be off and the interior dimmer switch must not be in the ⬙ party ⬙ or ⬙ parade ⬙ positions. Set theme note: when the “set th...

  • Page 461

    Setting name selectable options keyboard smart keyboard selection latin keyboard note: latin keyboard displays different keyboard layouts to choose from. The selectable keyboards are abcdef keyboard, qwerty keyboard, and azerty keyboard. Touchscreen beep control screen time-out — if equipped note: w...

  • Page 462

    Units after pressing the “units” button on the touchscreen, the following settings will be available: setting name selectable options units us metric custom note: the “custom” option allows you to set the “speed” (mph, or km/h), “distance” (mi, or km), “fuel consumption” [mpg (us), mpg (uk), l/100 k...

  • Page 463

    Clock after pressing the “clock” button on the touchscreen, the following settings will be available: setting name selectable options sync time with gps set time hours + - note: the “set time hours” feature will allow you to adjust the hours. The “sync time with gps” button on the touch- screen must...

  • Page 464

    Camera after pressing the “camera” button on the touchscreen, the following settings will be available: setting name selectable options surround view camera delay note: the “surround view camera delay” setting determines whether or not the screen will display the 360 degree view image with guideline...

  • Page 465

    Setting name selectable options parkview backup camera active guide lines — if equipped note: the “parkview backup camera active guide lines” feature overlays the rear backup camera image with active, or dynamic, grid lines to help illustrate the width of the vehicle and its project back up path, ba...

  • Page 466

    Setting name selectable options forward collision warning includes advanced brake assist (aba). The aba applies additional brake pressure when the driver requests insufficient brake pressure to avoid a potential frontal collision. When the “sound only” option is selected a chime will sound alerting ...

  • Page 467

    Setting name selectable options rear parksense chime volume low medium high front parksense chime volume low medium high rear parksense braking assist — if equipped note: when the “rear parksense braking assist” feature is selected, the park assist system will detect objects located be- hind the veh...

  • Page 468

    Setting name selectable options any damage in the area where the sensor is located, even if the fascia is not damaged, the sensor may have become misaligned. Take your vehicle to an authorized dealer to verify sensor alignment. A sensor that is misaligned will re- sult in the blind spot alert system...

  • Page 469

    Brakes setting — if equipped after pressing the “brakes” button on the touchscreen, the following settings will be available: setting name selectable options brake service yes no note: selecting the “brake service” feature will display a pop-up asking whether or you would like to retract the park br...

  • Page 470

    Setting name selectable options auto dim high beams — if equipped note: when the “auto dim high beams” feature is selected, the high beam headlights will activate/deactivate automati- cally under certain conditions. Daytime running lights — if equipped flash lights with lock doors & locks after pres...

  • Page 471

    Setting name selectable options auto unlock on exit note: when this feature is selected, all doors will unlock when the vehicle is stopped, the transmission is in the park or neutral position and the driver’s door is opened. Flash lights with lock sound horn with lock off 1st press 2nd press sound h...

  • Page 472

    Setting name selectable options passive entry — if equipped note: this feature allows you to lock and unlock the vehicles door(s) without having to push the key fob lock or unlock buttons. Personal settings linked to key fob — if equipped note: this feature provides automatic recall of all settings ...

  • Page 473

    Engine off options after pressing the “engine off options” button on the touchscreen, the following settings will be available: setting name selectable options engine off power delay — if equipped 0 sec 45 sec 5 min 10 min note: when the “engine off power delay” feature is selected, the power window...

  • Page 474

    Audio after pressing the “audio” button on the touchscreen, the following settings will be available: setting name selectable options balance/fade speaker icon note: when in this display you may adjust the “balance/fade” of the audio by pressing and dragging the “speaker icon” toward any location in...

  • Page 475

    Phone/bluetooth after pressing the “phone/bluetooth” button on the touch- screen, the following settings will be available: setting name selectable options phone pop-ups displayed in cluster do not disturb do not disturb options note: the “do not disturb” feature allows the paired phone to send a pr...

  • Page 476

    Siriusxm setup — if equipped after pressing the “siriusxm setup” button on the touch- screen, the following settings will be available: setting name selectable options sxm tune start note: the “tune start” feature begins playing the current song from the beginning when you tune to a music channel us...

  • Page 477

    Setting name selectable options 2. Write down the sirius id numbers for your receiver. To reactivate your service, either call the number listed on the screen or visit the provider online. Siriusxm travel link is a separate subscription. Accessibility — if equipped after pressing the “accessibility”...

  • Page 478

    Reset settings after pressing the “restore settings” button on the touch- screen, the following settings will be available: setting name selectable options reset app drawer ok cancel restore settings ok cancel note: when this feature is selected it will reset all settings to their default settings. ...

  • Page 479

    Srt performance pages — if equipped performance pages is an application that provides a dis- play for performance indicators, as received from the instrument cluster, that will help you gain familiarity with the capabilities of your vehicle in real-time. To access the performance pages, press the “a...

  • Page 480

    The following describes each feature and its operation: home when home is selected, a series of widgets (gauges) can be customized by the user. Follow these steps to change a widget: 1. Pressing any of the gauges allows you to switch the display. 2. Select the following option from the menu: • set w...

  • Page 481

    • timer: brake distance • timer: reaction time note: pressing the “camera” icon in the upper right corner of the performance pages screen will take a screenshot of the current screen and save it to a usb that is connected. Timers when the timers page is selected, you will be able to select from foll...

  • Page 482

    • with a usb jump drive installed, press the “usb” button to save to the jump drive. • press the “uconnect” button to save the runs to the owner web page. • press the “cancel” button to view the last timer “ticket”. The “tickets” contain the timers listed below: • reaction time measures the driver’s...

  • Page 483

    • ⅛ mile (200 meter) mph displays the vehicle speed at the time ⅛ mile was reached. • ¼ mile (400 meter) et displays the time it takes for the vehicle to go ¼ mile (400 meters). • ¼ mile (400 meter) mph displays the speed the vehicle was at when ¼ mile was reached. • brake distance ft displays the d...

  • Page 484

    • coolant temperature shows the actual coolant temperature. • battery voltage shows the actual battery voltage. • trans oil temp shows the current transmission oil temperature. • intake air temperature shows the actual air intake temperature. • boost pressure shows the current boost pressure. • air ...

  • Page 485

    G-force when selected, this screen displays all four g-force values, as well as steering angle. When g-force is selected, the following features will be available: • vehicle speed: measures the current speed of the vehicle in either mph or km/h, starting at zero with no maximum value. • front g-forc...

  • Page 486

    • steering wheel angle steering wheel angle utilizes the steering angle sensor to measure the degree of the steering wheel relative to zero. The zero degree measurement indicates a steering wheel straight ahead position. When the steering angle value is negative, a turn to the left is indicated, and...

  • Page 487

    • instantaneous torque shows the instantaneous torque. • oil pressure (6.4l only) shows the actual engine oil pressure. • gear (automatic transmission only) shows the current (or pending) operating gear of the vehicle. • boost pressure (6.2l only) shows the actual boost pressure. Dynamometer (dyno) ...

  • Page 488

    The following options can be selected: • pressing the stop button will freeze the graph. Selecting play will clear the graph and restart the process over • press the “+” or “–” buttons to change the history of the graph. The selectable options are “30, 60, 90, and 120 seconds. The graph will expand ...

  • Page 489

    • pressing the srt button on the console switch. • pressing the custom button on the selec-track switch. • selecting “drive modes” from the “apps” menu. • selecting “drive modes” from within the performance pages menu. The srt drive modes main screen displays the current drive mode and real-time sta...

  • Page 490

    Note: electronic stability control (esc) full-off can be activated by pushing and holding the esc off button on the instrument panel switch bank for five seconds. Sport mode selecting “sport” with the selec-track switch will activate the configuration for typical enthusiast driving. The trans- missi...

  • Page 491

    Stability control is set to “full” highlighted in blue. All-wheel drive is set to “50/50” highlighted in blue. Steering is set to “street” highlighted in yellow. Suspension is set to “sport” highlighted in orange. Snow mode selecting “snow” with the selec-track switch will activate snow mode for use...

  • Page 492

    Auto mode auto mode is enabled upon ignition on, or by selecting “auto” with the selec-track switch. The transmission, stability control and all-wheel drive modes are set to their “street” settings highlighted in yellow. Steering and suspension can be configured in either the “street,” “sport,” or “...

  • Page 493

    Custom mode custom mode may be selected by pushing the “custom” button on selec-track switch. Custom mode allows you to create a custom configuration that is saved for quick selection of your favorite settings. While in custom mode, the all-wheel drive, stability control, transmission, steer- ing, s...

  • Page 494

    Race options press the “race options” button on the touchscreen while in the drive modes screen, to display the vehicle’s launch control screen. Within race options, you can activate, deactivate, and adjust the rpm values for the launch control and shift light features. Launch control warning! Launc...

  • Page 495

    Launch control can be accessed by pushing the launch button on the selec-track switch or pushing the srt button on the selec-track switch then selecting the “race options” button on the touchscreen. Press the “activate launch control” button on the touchscreen to activate the feature. Press the “lau...

  • Page 496

    To adjust the launch rpm, drag the slider bar or press the arrows on the touchscreen to adjust the holding rpm. The launch rpm limit will display in the head units tachometer display. Shift light your vehicle is equipped with a shift light feature that illuminates the back lighting of the tachometer...

  • Page 497

    Factory default” button on the touchscreen to change back to factory settings, or press the “shift light off” button on the touchscreen to turn the system off completely. Valet mode to enter valet mode press the “valet” button on the touchscreen and a popup screen will ask you if you would like to e...

  • Page 498

    To exit valet mode you must enter the same four digit pin that was used to enter the mode. The unlock keypad can be accessed by either pushing the srt button on selec-track switch, or pressing the “valet” button on the touchscreen. The valet mode deactivation key pad will then prompt you for your fo...

  • Page 499

    Eco mode push the eco button on the center stack of the instrument panel to enter eco mode. Eco mode modifies the vehi- cle’s engine and transmission settings to provide improved fuel economy at a trade-off with acceleration performance. Increased engine exhaust noise and/or vibration may be noticed...

  • Page 500

    The right-hand control is a rocker-type switch with a push-button in the center and controls the volume and mode of the sound system. Pushing the top of the rocker switch will increase the volume, and pushing the bottom of the rocker switch will decrease the volume. Pushing the center button will ma...

  • Page 501

    Uconnect rear seat entertainment (rse) system — if equipped your rear seat entertainment system is designed to give your family years of enjoyment. You can play your favorite cds, dvds or blu-ray discs, listen to audio over the wireless headphones, or plug and play a variety of stan- dard video game...

  • Page 502

    • turn on the rear seat entertainment system by pushing the power button on the remote control. • when the video screen(s) are open and a dvd/blu-ray disc is inserted into the disc player, the screen(s) turn(s) on automatically, the headphone transmitters turn on and playback begins. • with the dual...

  • Page 503

    • the system can be controlled either by the front seat occupants utilizing the touchscreen radio or by the rear seat occupants using the remote control. Dual video screen note: typically there are two different ways to operate the features of the rear seat entertainment system. • the remote control...

  • Page 504

    3. To watch a blu-ray disc on rear 2 for passenger side rear passengers, ensure the remote control and headphone switch is on rear 2. Note: • to view a blu-ray disc on the radio, press the “media” button on the touchscreen, and then press the “disc” button. Press the “play” button, and then the “ful...

  • Page 505

    3. Rse mute mute rear headphones for the current ignition cycle. Press- ing mute again will unmute rear headphones. 4. Rse remote control lock out press to enable/disable remote control functions. 5. Rse channel 2 mode indicates the current source for screen 2/channel 2. This button will be highligh...

  • Page 506

    Play video games connect the video game console to the audio/video rca/hdmi input jacks located on the side of each seat. Audio/video rca/hdmi jacks (aux/hdmi jacks) on the side of each seat enable the monitor to display video directly from a video camera, connect video games for display on the scre...

  • Page 507

    Using the remote control 1. Push the source button on the remote control. 2. While looking at rear 1 or 2, highlight disc by either pushing up/down/left/right buttons, then push enter/ok. Using the touchscreen radio controls 1. Press the media button on the uconnect radio touch- screen. 2. Press the...

  • Page 508

    3. Press the 1 or 2 buttons on the touchscreen, and the select source button on the touchscreen. Press the disc button on the touchscreen in the media column. To exit, press the x at the top right of the screen. Note: pressing the screen on the radio while a dvd or blu-ray disc is playing, brings up...

  • Page 509

    Blu-ray disc player remote control — if equipped controls and indicators 1. Power — turns the screen and wireless headphone transmitter for the selected channel on or off. To hear audio while the screen is closed, push the power button to turn the headphone transmitter on. 2. Channel selector indica...

  • Page 510

    13. 䉳䉳 — push and hold to fast rewind through the current audio track or video chapter. 14. — mutes headphone audio. 15. Back — push to exit out of menus or return to source selection screen. 16. 䉲 — push to navigate menus. 17. Ok — push to select the highlighted option in a menu. 18. 䉳 — push to na...

  • Page 511

    Note: the rear video system must be turned on before sound can be heard from the headphones. To conserve battery life, the headphones will automatically turn off approximately three minutes after the rear video system is turned off. Changing the audio mode for headphones 1. Ensure the remote control...

  • Page 512

    Unwired stereo headphone lifetime limited warranty who does this warranty cover? This warranty covers the initial user or purchaser ( ⬙ you ⬙ or ⬙ your ⬙ ) of this particular unwired technology llc ( ⬙ unwired ⬙ ) wireless headphone ( ⬙ product ⬙ ). The warranty is not transferable. How long does th...

  • Page 513

    System information disc menu when listening to a cd audio or cd data disc, pushing the remote control’s pop up/menu button displays a list of all commands which control playback of the disc. Display settings when watching a video source (blu-ray disc or dvd video with the disc in play mode, aux vide...

  • Page 514

    • when the screen is reopened, the video screen will automatically turn back on and show the appropriate display menu or media. If the screen is closed and there is no audio heard, verify that the headphones are turned on (the on indicator is illuminated) and the headphone selector switch is on the ...

  • Page 515

    If you record a disc using a personal computer, there may be cases where the blu-ray disc player may not be able to play some or the entire disc, even if it is recorded in a compatible format and is playable on other players. To help avoid playback problems, use the following guidelines when recordi...

  • Page 516

    • other compression formats such as aac, mp3 pro, ogg vorbis, and atrac3 will not play. The blu-ray player will automatically skip the file and begin playing the next available file. • if you are creating your own files, the recommended fixed bit rate for mp3 files is between 96 and 192kbps and the ...

  • Page 517

    Radio operation and mobile phones under certain conditions, the mobile phone being on in your vehicle can cause erratic or noisy performance from your radio. This condition may be lessened or eliminated by relocating the mobile phone antenna. This condition is not harmful to the radio. If your radio...

  • Page 518

    Note: • this equipment has been tested and found to comply with the limits for a class b digital device, pursuant to part 15 of the fcc rules. These limits are designed to provide reasonable protection against harmful interfer- ence in a residential installation. This equipment gener- ates, uses and...

  • Page 519

    If you see the nav icon on your touchscreen, you have the uconnect 4c nav system. If not, you have a uconnect 4c system. Get started all you need to control your uconnect system with your voice are the buttons on your steering wheel. Helpful hints for using voice recognition: 1. Visit uconnectphone....

  • Page 520

    Push the vr button . After the beep, say: • “cancel” to stop a current voice session • “help” to hear a list of suggested voice commands • “repeat” to listen to the system prompts again notice the visual cues on the touchscreen that inform you of your voice recognition system’s status. Natural langu...

  • Page 521

    Media uconnect offers connections via usb, bluetooth and auxil- iary ports (if equipped). Voice operation is only available for connected usb and aux devices. (remote cd player optional and not available on all vehicles.) push the vr button . After the beep, say one of the following commands and fol...

  • Page 522

    Phone making and answering hands-free phone calls is easy with uconnect. When the phonebook button is illuminated on your touchscreen, your system is ready. Check uconnectphone.Com for mobile phone compatibility and pairing instructions. Push the phone button . After the beep, say one of the followi...

  • Page 523

    Climate (4c/4c nav) too hot? Too cold? Adjust vehicle temperatures hands-free and keep everyone comfortable while you keep moving ahead. (if vehicle is equipped with climate control.) push the vr button . After the beep, say one of the following commands: • “ set driver temperature to 70 degrees” • ...

  • Page 524

    Navigation (4c/4c nav) the uconnect navigation feature helps you save time and become more productive when you do not know exactly how to get to where you want to go. (navigation is optional on the uconnect 4c nav system. See an autho- rized dealer to activate navigation at any time.) 1. To enter a ...

  • Page 525

    Siriusxm guardian (4c nav) — if equipped caution! Some siriusxm guardian services, including sos call and roadside assistance call will not work without an operable lte (voice/data) or 3g or 4g (data) net- work connection compatible with your device. Note: your vehicle may be transmitting data as au...

  • Page 526

    3. Select “customer care” to speak with a siriusxm guardian customer care agent who will activate ser- vices in your vehicle, or select “enter email” to activate on the web. • u.S. Residents visit: www.Siriusxm.Com/guardian. • canadian residents visit: www.Siriusxm.Com/guardian/ca. Vehicle health re...

  • Page 527

    • press the location button on the navigation bar at the bottom of the app to bring up a map to locate your vehicle or send a location to your vehicle’s navigation system. • press the settings button in the upper left corner of the app to bring up app settings and access the assist call centers. Not...

  • Page 528

    Apple carplay — if equipped apple carplay allows you to use your voice to interact with siri through your vehicle’s voice recognition system, and use your smartphone’s data plan to project your iphone and a number of its apps onto your uconnect touchscreen. Connect your iphone 5, or higher, to one o...

  • Page 529

    Refer to your uconnect owner’s manual supplement for further information. Android auto — if equipped android auto allows you to use your voice to interact with android’s best-in-class speech technology through your vehicle’s voice recognition system, and use your smart- phone’s data plan to project ...

  • Page 530

    Refer to your uconnect owner’s manual supplement for further information. Android auto on 7-inch display android auto on 8.4-inch display 528 multimedia.

  • Page 531

    General information the following regulatory statement applies to all radio frequency (rf) devices equipped in this vehicle: this device complies with part 15 of the fcc rules and with industry canada license-exempt rss standard(s). Operation is subject to the following two conditions: 1. This devic...

  • Page 532

    Cd/dvd disc maintenance to keep a cd/dvd in good condition, take the following precautions: 1. Handle the disc by its edge; avoid touching the surface. 2. If the disc is stained, clean the surface with a soft cloth, wiping from center to edge. 3. Do not apply paper or tape to the disc; avoid scratch...

  • Page 533

    Customer assistance contents 䡵 suggestions for obtaining service for your vehicle . . . . . . . . . . . . . . . . . . . . . . . .532 ▫ prepare for the appointment . . . . . . . . . . . . . .532 ▫ prepare a list . . . . . . . . . . . . . . . . . . . . . . . . .532 ▫ be reasonable with requests . . . ...

  • Page 534

    Suggestions for obtaining service for your vehicle prepare for the appointment if you are having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty. Discuss additional charges with the service manager....

  • Page 535

    Any communication to the manufacturer’s customer center should include the following information: • owner’s name and address • owner’s telephone number (home and office) • authorized dealer name • vehicle identification number (vin) • vehicle delivery date and mileage fca us llc customer center p.O....

  • Page 536

    Customer assistance for the hearing or speech impaired (tdd/tty) to assist customers who have hearing difficulties, the manufacturer has installed special tdd (telecommunica- tion devices for the deaf) equipment at its customer center. Any hearing or speech impaired customer, who has access to a tdd...

  • Page 537

    Warning! Engine exhaust (internal combustion engines only), some of its constituents, and certain vehicle compo- nents contain, or emit, chemicals known to the state of california to cause cancer and birth defects, or other reproductive harm. In addition, certain fluids con- tained in vehicles and c...

  • Page 538

    In canada if you believe that your vehicle has a safety defect, you should contact the customer service department immediately. Canadian customers who wish to report a safety defect to the canadian government should contact transport canada, motor vehicle defect investigations and recalls at 1-800-3...

  • Page 539

    Index 12.

  • Page 540

    About your brakes . . . . . . . . . . . . . . . . . . . . . . . . .442 adaptive cruise control (acc) (cruise control) . . . .258 adding engine coolant (antifreeze) . . . . . . . . . . . . .405 adding fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .321 additives, fuel . . . . . . . . ...

  • Page 541

    Adding fluid . . . . . . . . . . . . . . . . . . . . . . . .410, 450 autostick . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .247 fluid and filter changes . . . . . . . . . . . . . . . . . . .410 fluid change . . . . . . . . . . . . . . . . . . . . . . . . . . .410 fluid level check . . ...

  • Page 542

    Car washes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .436 cellular phone . . . . . . . . . . . . . . . . . . . . . . . . . . . .515 certification label . . . . . . . . . . . . . . . . . . . . . . . . . .324 chains, tire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .432 ...

  • Page 543

    Daytime running lights . . . . . . . . . . . . . . . . . . . . . .64 dealer service . . . . . . . . . . . . . . . . . . . . . . . . . . . . .384 defroster, windshield. . . . . . . . . . . . . . . . . . . . . . . .224 diagnostic system, onboard . . . . . . . . . . . . . . . . . . .144 dipsticks oil (...

  • Page 544

    Overheating . . . . . . . . . . . . . . . . . . . . . . . . . . . .368 starting . . . . . . . . . . . . . . . . . . . . . . . . . . . .232, 233 engine oil viscosity . . . . . . . . . . . . . . . . . . . . .385, 386 enhanced accident response feature . . . . . . . . .204, 374 ethanol. . . . . . . . ....

  • Page 545

    Gear ranges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .242 glass cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . .439 gross axle weight rating. . . . . . . . . . . . . . . . . . . . .326 gross vehicle weight rating . . . . . . . . . . . . . . . . . . .326 gvwr . . . . ...

  • Page 546

    Programming additional key fobs . . . . . . . . . .23, 30 key fob battery service (remote keyless entry) . . . . .21 key fob programming (remote keyless entry) . . . . . .23 key-in reminder. . . . . . . . . . . . . . . . . . . . . . . . . . . .25 keyless enter-n-go. . . . . . . . . . . . . . . . . ....

  • Page 547

    Load shed battery saver mode . . . . . . . . . . . . . . . . . . . . . . .130 battery saver on . . . . . . . . . . . . . . . . . . . . . . . . .130 electrical load reduction . . . . . . . . . . . . . . . . . . .130 intelligent battery sensor . . . . . . . . . . . . . . . . . . .130 locks auto unlock...

  • Page 548

    Oil filter, change . . . . . . . . . . . . . . . . . . . . . . . . . .387 oil filter, selection. . . . . . . . . . . . . . . . . . . . . . . . . .387 oil pressure light . . . . . . . . . . . . . . . . . . . . . . . . . .136 onboard diagnostic system . . . . . . . . . . . . . . . . . . .144 opener, g...

  • Page 549

    Rear cross path. . . . . . . . . . . . . . . . . . . . . . . . . . . .169 rear cupholder. . . . . . . . . . . . . . . . . . . . . . . . . . . .108 rear parksense system . . . . . . . . . . . . . . . . . . .277, 285 rear seat, folding . . . . . . . . . . . . . . . . . . . . . . . .41, 43 rear wiper/w...

  • Page 550

    Seat belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . .181, 224 adjustable shoulder belt . . . . . . . . . . . . . . . . . . .187 adjustable upper shoulder anchorage . . . . . . . . .187 child restraint . . . . . . . . . . . . . . . . . . . . . . . . . .206 extender . . . . . . . . . . ...

  • Page 551

    Accel/decel (acc only) . . . . . . . . . . . . . . . . . . .263 cancel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .258 resume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .257 set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .256 speed control...

  • Page 552

    Quality grading . . . . . . . . . . . . . . . . . . . . . . . . .434 radial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .423 replacement . . . . . . . . . . . . . . . . . . . . . . . . .364, 426 rotation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .433 safety . . . ...

  • Page 553

    Vanity mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62 vehicle identification number (vin) . . . . . . . . . . . . .442 vehicle loading . . . . . . . . . . . . . . . . . . . . . . . .324, 418 vehicle modifications/alterations. . . . . . . . . . . . . . . . .8 vehicle security ala...

  • Page 555

    Installation of radio transmitting equipment special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained person- nel. The following must be obs...

  • Page 556

    Grand cherokee srt o w n e r ’ s m a n u a l second edition printed in the u.S.A. 18wksrt-126-ab ©2017 fca us llc. All rights reserved. Jeep is a registered trademark of fca us llc. 2 0 1 8 stick with the specialists ® gr and cher ok ee sr t 20 18.