1. DL manuals
  2. Jeep
  3. Automobile
  4. Patriot 2015
  5. Owner's Manual

Jeep Patriot 2015 Owner's Manual

Other manuals for Patriot 2015: User Manual

Summary of Patriot 2015

  • Page 1

    Patriot o w n e r ’ s m a n u a l 20 15 p a triot 15mk74-126-ad fourth edition printed in u.S.A. 2 0 1 5 fca us llc.

  • Page 2

    Vehicles sold in canada with respect to any vehicles sold in canada, the name fca us llc shall be deemed to be deleted and the name chrysler canada inc. Used in substitution therefore. Driving and alcohol drunken driving is one of the most frequent causes of accidents. Your driving ability can be se...

  • Page 3: Table Of Contents

    Table of contents section page 1 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 things to know before starting your vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 3 understa...

  • Page 5: Introduction

    Introduction contents ! Introduction . . . . . . . . . . . . . . . . . . . . . . . .4 ! Rollover warning . . . . . . . . . . . . . . . . . . .4 ! How to use this manual . . . . . . . . . . . . . .5 ! Warnings and cautions . . . . . . . . . . . . . .7 ! Vehicle identification number . . . . . . . .7 ...

  • Page 6

    Introduction congratulations on selecting your new fca us llc vehicle. Be assured that it represents precision workman- ship, distinctive styling, and high quality - all essentials that are traditional to our vehicles. This owner’s manual has been prepared with the assis- tance of service and engine...

  • Page 7

    Control. Failure to operate this vehicle safely may result in a collision, rollover of the vehicle, and severe or fatal injury. Drive carefully. Failure to use the driver and passenger seat belts pro- vided is a major cause of severe or fatal injury. In fact, the u.S. Government notes that the unive...

  • Page 8

    6 introduction.

  • Page 9

    Warnings and cautions this owner’s manual contains warnings against operating procedures that could result in a collision or bodily injury. It also contains cautions against proce- dures that could result in damage to your vehicle. If you do not read this entire owner’s manual, you may miss importan...

  • Page 10

    Note: it is illegal to remove or alter the vin. Vehicle modifications/alterations warning! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a collision resulting in serious injury or death. Right front body vin location 8 introduct...

  • Page 11: Contents

    Things to know before starting your vehicle contents ! A word about your keys . . . . . . . . . . . . .12 ▫ ignition key removal . . . . . . . . . . . . . . . . . . .12 ▫ locking doors with a key. . . . . . . . . . . . . . . .14 ▫ key-in-ignition reminder . . . . . . . . . . . . . . . .14 ! Sentry k...

  • Page 12

    ▫ sound horn with remote key lock . . . . . . . . .22 ▫ flash lights with remote key lock/unlock . . .23 ▫ using the panic alarm . . . . . . . . . . . . . . . . . .24 ▫ programming additional transmitters. . . . . . . .25 ▫ transmitter battery replacement . . . . . . . . . . .25 ▫ general informatio...

  • Page 13

    ! Safety tips . . . . . . . . . . . . . . . . . . . . . . . . .100 ▫ transporting passengers . . . . . . . . . . . . . . . . .100 ▫ exhaust gas . . . . . . . . . . . . . . . . . . . . . . . . .101 ▫ safety checks you should make inside the vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Page 14

    A word about your keys the authorized dealer that sold you your new vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys. Ask your authorized dealer for these numbers and keep them in a safe place. Ignition key removal 1. Place the shift lever in...

  • Page 15

    Note: if you try to remove the key before you place the shift lever in park, the key may become trapped tem- porarily in the ignition switch cylinder. If this occurs, place the shift lever in park, rotate the key clockwise slightly, and then remove the key as described above. If a malfunction occurs...

  • Page 16

    Warning! (continued) • allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Chil- dren should be warned not to touch the parking brake, brake pedal or the gear selector. • do not leave the key fob in or near th...

  • Page 17

    Sentry key® the sentry key® immobilizer system prevents unau- thorized vehicle operation by disabling the engine. The system does not need to be armed or activated. Operation is automatic, regardless of whether the vehicle is locked or unlocked. The system uses ignition keys that have an embedded el...

  • Page 18

    Caution! The sentry key® immobilizer system is not compat- ible with some aftermarket remote starting systems. Use of these systems may result in vehicle starting problems and loss of security protection. All of the keys provided with your new vehicle have been programmed to the vehicle electronics....

  • Page 19

    Customer key programming if you have two valid sentry keys®, you can program new sentry keys® to the system by performing the following procedure: 1. Cut the additional sentry key® transponder blank(s) to match the ignition switch lock cylinder key code. 2. Insert the first valid key into the igniti...

  • Page 20

    Note: if a programmed key is lost, see your authorized dealer to have all remaining keys erased from the sys- tem’s memory. This will prevent the lost key from starting your vehicle. The remaining keys must then be reprogrammed. All vehicle keys must be taken to an authorized dealer at the time of s...

  • Page 21

    To arm the system 1. Remove the key from the ignition switch and get out of the vehicle. 2. Lock the door using either the power door lock switch or the remote keyless entry (rke) transmitter and close all doors. 3. The vehicle security light in the instrument cluster will flash rapidly for approxim...

  • Page 22

    Once the vehicle security alarm is armed (after 16 seconds), when you pull the door handle to exit, the alarm will sound. If this occurs, push the unlock button on the rke transmitter to disarm the vehicle security alarm. Vehicle security alarm manual override the vehicle security alarm will not arm...

  • Page 23

    To unlock the doors and liftgate push and release the unlock button on the rke transmitter once to unlock the driver’s door or twice within five seconds to unlock all doors and liftgate. The turn signal lights will flash to acknowledge the unlock signal. The illuminated entry system will also turn o...

  • Page 24

    Note: pushing the lock button on the rke transmitter while you are inside the vehicle will activate the vehicle security alarm. Opening a door with the vehicle security alarm activated will cause the alarm to sound. Push the unlock button to deactivate the vehicle security alarm. Illuminated approac...

  • Page 25

    • for vehicles not equipped with the evic, perform the following steps: 1. Push the lock button on a programmed rke transmitter for at least 4 seconds, but no longer than 10 seconds. Then, push the panic button while still holding the lock button. 2. Release both buttons at the same time. 3. Test th...

  • Page 26

    • for vehicles not equipped with the evic, perform the following steps: 1. Push and hold the unlock button on a pro- grammed rke transmitter for at least 4 seconds but no longer than 10 seconds. Then, push and hold the lock button while still holding the unlock button. 2. Release both buttons at the...

  • Page 27

    Note: when you turn off the panic alarm by pushing the panic button a second time, you may have to move closer to the vehicle due to the radio frequency noises of the system. Programming additional transmitters refer to “sentry key®” in “things to know before starting” for further information. If yo...

  • Page 28

    3. To reassemble the rke transmitter case, snap the two halves together. Note: if the rke transmitter is equipped with a screw, reinstall and tighten the screw until snug. General information this device complies with part 15 of the fcc rules and rss 210 of industry canada. Operation is subject to t...

  • Page 29

    Note: • the vehicle must be equipped with an automatic transmission to be equipped with remote start. • obstructions between the vehicle and the key fob may reduce this range. How to use remote start all of the following conditions must be met before the engine will remote start: • shift lever in pa...

  • Page 30

    Remote start abort message on electronic vehicle information center (evic) — if equipped the following messages will display in the evic if the vehicle fails to remote start or exits remote start prema- turely: • remote start aborted — door ajar • remote start aborted — hood ajar • remote start abor...

  • Page 31

    • the engine can be started two consecutive times (two 15-minute cycles) with the rke transmitter. However, the ignition switch must be cycled to the on/run position before you can repeat the start sequence for a third cycle. Remote start will also cancel if any of the following occur: • the engine ...

  • Page 32

    Door locks manual door locks use the manual door lock knob to lock the doors from inside the vehicle. If the lock knob is down when the door is closed, the door will lock. Make sure the keys are not inside the vehicle before closing the door. Warning! • for personal security and safety in the event ...

  • Page 33

    Caution! An unlocked vehicle is an invitation to thieves. Always remove the key from the ignition and lock all of the doors when leaving the vehicle unattended. Power door locks a power door lock switch is located on the driver’s and front passenger’s door panel. Push this switch to lock or unlock t...

  • Page 34

    Auto lock doors — if equipped the auto door lock feature default condition is enabled. When enabled, the door locks will lock automatically when the vehicle’s speed exceeds 15 mph (24 km/h). Auto lock doors programming the automatic door locks feature can be enabled or disabled as follows: • for veh...

  • Page 35

    Automatic unlock doors on exit the doors will unlock automatically if: • the automatic unlock doors on exit feature is en- abled. • the transmission was in gear, and the vehicle speed returned to 0 mph (0 km/h). • the transmission is in neutral or park. • the driver’s door is opened. • the doors wer...

  • Page 36

    Note: • if you do not hear the chime, it means that the system did not enter the programming mode and you will need to repeat the procedure. • use the automatic unlock doors on exit feature in accordance with local laws. Child-protection door lock system — rear doors to provide a safer environment f...

  • Page 37

    Warning! Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child-protection locks are engaged. Note: for emergency exit with the system engaged, move the lock knob up (unlocked position), roll down the window, and open the do...

  • Page 38

    Note: • for vehicles not equipped with the electronic vehicle information center (evic), the power window switches will remain active for 45 seconds after the ignition switch is turned to the lock position. Open- ing either front door will cancel this feature. • for vehicles equipped with the evic, ...

  • Page 39

    Auto-down the driver’s door window switch has an auto-down feature. Push the window switch past the first detent, release, and the window will go down automatically. To cancel the auto-down movement, operate the switch in either the up or down direction and release the switch. Power window switch lo...

  • Page 40

    Window lockout switch the window lockout switch on the driver’s door allows you to disable the window controls on the rear passenger doors. To disable the window controls on the rear pas- senger doors, push the window lockout switch. To enable the rear window controls, push the window lockout switch...

  • Page 41

    Liftgate note: the key that is used to start the vehicle is also used to lock or unlock the doors and open the liftgate. To unlock the liftgate, insert the key into the lock and turn to the right (manual lock models only). The liftgate can also be unlocked using the remote keyless entry (rke) transm...

  • Page 42

    Warning! • driving with the liftgate open can allow poisonous exhaust gases into your vehicle. You and your passengers could be injured by these fumes. Keep the liftgate closed when you are operating the vehicle. • if you are required to drive with the liftgate open, make sure that all windows are c...

  • Page 43

    Here are some simple steps you can take to minimize the risk of harm from a deploying air bag: 1. Children 12 years old and under should always ride buckled up in a vehicle with a rear seat. 2. If a child from 2 to 12 years old (not in a rear-facing child restraint) must ride in the front passenger ...

  • Page 44

    Warning! • never place a rear-facing child restraint in front of an air bag. A deploying passenger advanced front air bag can cause death or serious injury to a child 12 years or younger, including a child in a rear- facing child restraint. • only use a rear-facing child restraint in a vehicle with ...

  • Page 45

    After the sequence completes, the seat belt reminder light remains illuminated until the respective seat belts are buckled. The driver should instruct all other occu- pants to buckle their seat belts. If an outboard front seat belt is unbuckled while traveling at speeds greater than 5 mph (8 km/h), ...

  • Page 46

    Warning! • relying on the air bags alone could lead to more severe injuries in a collision. The air bags work with your seat belt to restrain you properly. In some collisions, the air bags won’t deploy at all. Always wear your seat belt even though you have air bags. • in a collision, you and your p...

  • Page 47

    Warning! (continued) • a lap belt worn too high can increase the risk of injury in a collision. The seat belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap part of your seat belt as low as possible and keep it snug. • a twisted seat belt may not pro...

  • Page 48

    Warning! (continued) • a shoulder belt placed behind you will not protect you from injury during a collision. You are more likely to hit your head in a collision if you do not wear your shoulder belt. The lap and shoulder belt are meant to be used together. • a frayed or torn seat belt could rip apa...

  • Page 49

    3. When the seat belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” 4. Position the lap belt so that it is snug and lies low across your hips, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt i...

  • Page 50

    6. To release the seat belt, push the red button on the buckle. The seat belt will automatically retract to its stowed position. If necessary, slide the latch plate down the webbing to allow the seat belt to retract fully. Second row center seat belt operating instructions the second row center seat...

  • Page 51

    Routing the rear center shoulder belt connecting mini-latch to buckle 2 things to know before starting your vehicle 49.

  • Page 52

    2. Grasp the mini-latch plate and pull the seat belt over the seat. 3. Route the shoulder belt to the inside of the right head restraint. Rear center seat belt buckled detaching mini-latch and buckle 50 things to know before starting your vehicle.

  • Page 53

    4. When the seat belt is long enough to fit, insert the mini-latch plate into the mini-buckle until you hear a “click.” 5. Sit back in seat. Slide the regular latch plate up the webbing as far as necessary to allow the seat belt to go around your lap. 6. When the seat belt is long enough to fit, ins...

  • Page 54

    Warning! (continued) • when reattaching the mini-latch and mini-buckle, ensure the seat belt webbing is not twisted. If the webbing is twisted, follow the preceding proce- dure to detach the mini-latch and mini-buckle, untwist the webbing, and reattach the mini-latch and mini-buckle. Lap/shoulder be...

  • Page 55

    As a guide, if you are shorter than average, you will prefer the shoulder belt anchorage in a lower position, and if you are taller than average, you will prefer the shoulder belt anchorage in a higher position. After you release the anchorage button, try to move it up or down to make sure that it i...

  • Page 56

    Warning! • only use a seat belt extender if it is physically required in order to properly fit the original seat belt system. Do not use the seat belt extender if, when worn, the distance between the front edge of the seat belt extender buckle and the center of the occupant’s body is less than 6 inc...

  • Page 57

    The pretensioners are triggered by the occupant re- straint controller (orc). Like the air bags, the preten- sioners are single use items. A deployed pretensioner or a deployed air bag must be replaced immediately. Energy management feature this vehicle has a seat belt system with an energy manageme...

  • Page 58

    If the passenger seating position is equipped with an alr and is being used for normal usage, only pull the seat belt webbing out far enough to comfortably wrap around the occupant’s mid-section so as to not activate the alr. If the alr is activated, you will hear a clicking sound as the seat belt r...

  • Page 59

    How to disengage the automatic locking mode unbuckle the combination lap/shoulder belt and allow it to retract completely to disengage the automatic locking mode and activate the vehicle sensitive (emergency) locking mode. Warning! • the seat belt assembly must be replaced if the switchable automati...

  • Page 60

    How the active head restraints (ahr) work the occupant restraint controller (orc) determines whether the severity, or type of rear impact will require the active head restraints (ahr) to deploy. If a rear impact requires deployment, both the driver and front passenger seat ahrs will be deployed. Whe...

  • Page 61

    Warning! All occupants, including the driver, should not oper- ate a vehicle or sit in a vehicle’s seat until the head restraints are placed in their proper positions in order to minimize the risk of neck injury in the event of a collision. Note: refer to “adjusting active head restraints” in “under...

  • Page 62

    3. Pull down then rearward towards the rear of the vehicle then down to engage the locking mechanism. A — downward movement b — rearward movement c — final downward movement to engage locking mechanism review table below 60 things to know before starting your vehicle.

  • Page 63

    4. The ahr front soft foam and trim half should lock into the back decorative plastic half. Note: • if you have difficulties or problems resetting the active head restraints, see an authorized dealer. • for safety reasons, have the active head restraints checked by a qualified specialist at an autho...

  • Page 64

    • advanced front air bags • supplemental side air bags • front and side impact sensors • seat belt pretenioners • seat belt buckle switch • seat track position sensors advanced front air bags this vehicle has advanced front air bags for both the driver and front passenger as a supplement to the seat...

  • Page 65

    Warning! • being too close to the steering wheel or instrument panel during advanced front air bag deployment could cause serious injury, including death. Air bags need room to inflate. Sit back, comfortably extending your arms to reach the steering wheel or instrument panel. • never place a rear-fa...

  • Page 66

    Warning! • no objects should be placed over or near the air bag on the instrument panel or steering wheel, because any such objects could cause harm if the vehicle is in a collision severe enough to cause the air bags to inflate. • do not put anything on or around the air bag covers or attempt to op...

  • Page 67

    On the other hand, depending on the type and location of impact, advanced front air bags may deploy in crashes with little vehicle front-end damage but that produce a severe initial deceleration. Because air bag sensors measure vehicle deceleration over time, vehicle speed and damage by themselves a...

  • Page 68

    Supplemental side air bags your vehicle is equipped with two types of side air bags: 1. Supplemental seat-mounted side air bags (sabs): located in the outboard side of the front seats. The sabs are marked with a # srs airbag # or # airbag # label sewn into the outboard side of the seats. The sabs ma...

  • Page 69

    When the sab deploys, it opens the seam on the out- board side of the seatback’s trim cover. The inflating sab deploys through the seat seam into the space between the occupant and the door. The sab moves at a very high speed and with such a high force that it could injure you if you are not seated ...

  • Page 70

    Sabics may help reduce the risk of head injury to front and rear seat outboard occupants. Sabics may reduce the risk of injuries in certain side impact and vehicle rollover events, in addition to the injury reduction poten- tial provided by the seat belts and body structure. The sabics deploy downwa...

  • Page 71

    The sabics and sabs (“side air bags”) are designed to activate in certain side impacts and certain rollover events. The occupant restraint controller (“orc”) de- termines whether the deployment of the side air bags in a particular side impact or rollover event is appropriate, based on the severity a...

  • Page 72

    Warning! (continued) • relying on the side air bags alone could lead to more severe injuries in a collision. The side air bags work with your seat belt to restrain you properly. In some collisions, side air bags won’t deploy at all. Always wear your seat belt even though you have side air bags. Note...

  • Page 73

    The side air bags will not deploy in all rollover events. The rollover sensing-system determines if a rollover event may be in progress and whether deployment is appropriate. A slower-developing event may deploy the seat belt pretensioners on both sides of the vehicle. A faster-developing event may ...

  • Page 74

    Continues, see your doctor. If these particles settle on your clothing, follow the garment manufacturer’s in- structions for cleaning. Do not drive your vehicle after the air bags have de- ployed. If you are involved in another collision, the air bags will not be in place to protect you. Warning! De...

  • Page 75

    • turn on the interior lights, which remain on as long as the battery has power or until the ignition is placed in the “off” position. • unlock the doors automatically. System reset procedure in order to reset the enhanced accident response system functions after an event, the ignition must be chang...

  • Page 76

    Diagnostics also record the nature of the malfunction. While the air bag system is designed to be maintenance free, if any of the following occurs, have an authorized dealer service the air bag system immediately. • the air bag warning light does not come on during the four to eight seconds when the...

  • Page 77

    Maintaining your air bag system warning! • modifications to any part of the air bag system could cause it to fail when you need it. You could be injured if the air bag system is not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the s...

  • Page 78

    Event data recorder (edr) this vehicle is equipped with an event data recorder (edr). The main purpose of an edr is to record, in certain crash or near crash-like situations, such as an air bag deployment or hitting a road obstacle, data that will assist in understanding how a vehicle’s systems per-...

  • Page 79

    Child restraints everyone in your vehicle needs to be buckled up at all times, including babies and children. Every state in the united states, and every canadian province, requires that small children ride in proper restraint systems. This is the law, and you can be pros- ecuted for ignoring it. Ch...

  • Page 80

    There are different sizes and types of restraints for children from newborn size to the child almost large enough for an adult seat belt. Always check the child seat owner’s manual to make sure you have the correct seat for your child. Carefully read and follow all the instruc- tions and warnings in...

  • Page 81

    Summary of recommendations for restraining children in vehicles child size, height, weight or age recommended type of child restraint infants and toddlers children who are two years old or younger and who have not reached the height or weight limits of their child re- straint either an infant carrie...

  • Page 82

    Infants and child restraints safety experts recommend that children ride rear-facing in the vehicle until they are two years old or until they reach either the height or weight limit of their rear-facing child restraint. Two types of child restraints can be used rear-facing: infant carriers and conv...

  • Page 83

    Older children and child restraints children who are two years old or who have outgrown their rear-facing convertible child seat can ride forward- facing in the vehicle. Forward-facing child seats and convertible child seats used in the forward-facing direc- tion are for children who are over two ye...

  • Page 84

    Warning! • improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the child restraint manufacturer’s directions exactly when installing an infant or child restraint. • after a child restraint i...

  • Page 85

    2. Do the child’s knees bend comfortably over the front of the vehicle seat – while they are still sitting all the way back? 3. Does the shoulder belt cross the child’s shoulder between their neck and arm? 4. Is the lap part of the seat belt as low as possible, touching the child’s thighs and not th...

  • Page 86

    Recommendations for attaching child restraints restraint type combined weight of the child + child restraint use any attachment method shown with an “x” below latch – lower anchors only seat belt only latch – lower anchors + top tether anchor seat belt + top tether anchor rear-facing child restraint...

  • Page 87

    Lower anchors and tethers for children (latch) restraint system your vehicle is equipped with the child restraint anchor- age system called latch, which stands for lower anchors and tethers for children. The latch system has three vehicle anchor points for installing latch- equipped child seats. The...

  • Page 88

    Latch positions for installing child restraints in this vehicle • lower anchorage symbol 2 anchorages per seating position • top tether anchorage symbol 86 things to know before starting your vehicle.

  • Page 89

    Latch position table what is the weight limit (child’s weight + weight of the child restraint) for using the latch anchorage system to attach the child restraint? 65 lbs (29.5 kg) use the latch anchorage system until the combined weight of the child and the child restraint is 65 lbs (29.5 kg). Use t...

  • Page 90

    Latch position table can two child restraints be attached using a common lower latch anchorage? No never “share” a latch anchorage with two or more child restraints. If the center position does not have dedicated latch lower anchorages, use the seat belt to in- stall a child seat in the center posit...

  • Page 91

    Locating latch anchorages the lower anchorages are round bars that are found at the rear of the seat cushion where it meets the seatback. They are just visible when you lean into the rear seat to install the child restraint. You will easily feel them if you run your finger along the gap between the ...

  • Page 92

    Locating tether anchorages there are tether strap anchorages behind each rear seating position located on the back of the seat. Latch-compatible child restraint systems will be equipped with a rigid bar or a flexible strap on each side. Each will have a hook or connector to attach to the lower ancho...

  • Page 93

    Restraints with flexible, webbing mounted lower attach- ments can be installed in any rear seating position. Warning! Never use the same lower anchorage to attach more than one child restraint. If you are installing latch- compatible child restraints next to each other, you must use the seat belt fo...

  • Page 94

    3. Attach the lower hooks or connectors of the child restraint to the lower anchorages in the selected seat- ing position. 4. If the child restraint has a tether strap, connect it to the top tether anchorage. See the section “installing child restraints using the top tether anchorage” for direc- tio...

  • Page 95

    Warning! • improper installation of a child restraint to the latch anchorages can lead to failure of the re- straint. The child could be badly injured or killed. Follow the child restraint manufacturer’s directions exactly when installing an infant or child restraint. • child restraint anchorages ar...

  • Page 96

    Lap/shoulder belt systems for installing child restraints in this vehicle • alr = switchable automatic locking retractor • top tether anchorage symbol 94 things to know before starting your vehicle.

  • Page 97

    Lap/shoulder belt systems what is the weight limit (child’s weight + weight of the child re- straint) for using the tether anchor with the seat belt to attach a for- ward facing child restraint? Weight limit of the child restraint always use the tether anchor when using the seat belt to install a fo...

  • Page 98

    Installing a child restraint with a switchable automatic locking retractor (alr) 1. Place the child seat in the center of the seating position. For some second row seats, you may need to recline the seat and/or raise the head restraint to get a better fit. If the rear seat can be moved forward and r...

  • Page 99

    8. If the child restraint has a top tether strap and the seating position has a top tether anchorage, connect the tether strap to the anchorage and tighten the tether strap. See the section “installing child restraints using the top tether anchorage” for directions to attach a tether anchor. 9. Test...

  • Page 100

    1. Look behind the seating position where you plan to install the child restraint to find the tether anchorage. You may need to move the seat forward to provide better access to the tether anchorage. If there is no top tether anchorage for that seating position, move the child restraint to another p...

  • Page 101

    Warning! • an incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchorage position directly behind the child seat to secure a child restraint top tether strap. • if your vehicle is equipped with a split rear seat, make sure the tethe...

  • Page 102

    Caution! Never use non-detergent oil or straight mineral oil in the engine or damage may result. Note: a new engine may consume some oil during its first few thousand miles (kilometers) of operation. This should be considered a normal part of the break-in and not interpreted as a problem. Safety tip...

  • Page 103

    Exhaust gas warning! Exhaust gases can injure or kill. They contain carbon monoxide (co), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing (co), follow these safety tips: • do not run the engine in a closed garage or in confined...

  • Page 104

    Safety checks you should make inside the vehicle seat belts inspect the seat belt system periodically, checking for cuts, frays, and loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Front seat belt assemblies must be replaced after a collision. Rear s...

  • Page 105

    Warning! Pedals that cannot move freely can cause loss of vehicle control and increase the risk of serious per- sonal injury. • always make sure that floor mats are properly attached to the floor mat fasteners. • never place or install floor mats or other floor coverings in the vehicle that cannot b...

  • Page 106

    Periodic safety checks you should make outside the vehicle tires examine tires for excessive tread wear and uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread or sidewall. Inspect the tread for cuts and cracks. Inspect sidewalls for cuts, cracks, and bulges. C...

  • Page 107: Contents

    Understanding the features of your vehicle contents ! Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . .109 ▫ inside day/night mirror . . . . . . . . . . . . . . . .109 ▫ automatic dimming mirror — if equipped . . .110 ▫ outside mirror — driver side . . . . . . . . . . . .111 ▫ outside ...

  • Page 108

    ! Voice command — if equipped . . . . . . . .145 ▫ voice command system operation . . . . . . . . .145 ▫ commands . . . . . . . . . . . . . . . . . . . . . . . . .147 ▫ voice training . . . . . . . . . . . . . . . . . . . . . . .151 ! Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

  • Page 109

    ▫ map/reading lights . . . . . . . . . . . . . . . . . . .171 ! Windshield wipers and washers . . . . . .172 ▫ windshield wiper operation . . . . . . . . . . . . .174 ▫ intermittent wiper system . . . . . . . . . . . . . . .174 ▫ windshield washers . . . . . . . . . . . . . . . . . . .175 ▫ mist fea...

  • Page 110

    ▫ opening sunroof — manual mode . . . . . . . . .192 ▫ closing sunroof — express. . . . . . . . . . . . . . .192 ▫ closing sunroof — manual mode . . . . . . . . . .193 ▫ pinch protect feature . . . . . . . . . . . . . . . . . . .193 ▫ venting sunroof — express . . . . . . . . . . . . . .193 ▫ sunsha...

  • Page 111

    Mirrors inside day/night mirror a two-point pivot system allows for horizontal and vertical mirror adjustment. Adjust the mirror to center on the view through the rear window. Headlight glare can be reduced by moving the small control under the mirror to the night position (toward the rear of vehicl...

  • Page 112

    Automatic dimming mirror — if equipped this mirror automatically adjusts for headlight glare from vehicles behind you. You can turn the feature on or off by pushing the button at the base of the mirror. A light to the left of the button will illuminate to indicate when the dimming feature is activat...

  • Page 113

    Outside mirror — driver side adjust the flat outside mirror so you can just see the side of your vehicle in the part of the mirror closest to the vehicle with your head close to the door glass. Outside mirror — passenger side adjust the convex outside mirror so you can just see the side of your vehi...

  • Page 114

    Power mirrors the power mirror control is located on the driver’s door trim panel. To adjust a mirror, turn the control wand toward the left or right mirror positions indicated. Tilt the control wand in the direction you want the mirror to move. When you are finished adjusting the mirror, turn the c...

  • Page 115

    Vanity mirrors — if equipped to use the vanity mirror, rotate the sun visor down and swing the mirror cover upward. Sun visor “slide-on-rod” feature — if equipped the sun visors may be extended out to provide more coverage of the side glass. Uconnect® phone — if equipped uconnect® phone is a voice-a...

  • Page 116

    For uconnect® customer support: • u.S. Residents - visit uconnectphone.Com or call 1-877- 855-8400. • canadian residents - visit uconnectphone.Com or call, 1-800-465-2001 (english) or 1-800-387-9983 (french). Uconnect® phone allows you to transfer calls between the system and your mobile phone as yo...

  • Page 117

    Uconnect® phone button the radio or steering wheel controls (if equipped) will contain the two control buttons (uconnect® phone button and voice com- mand button) that will enable you to access the system. When you push the button you will hear the word uconnect® followed by a beep. The beep is your...

  • Page 118

    • prior to giving a voice command, one must wait for the beep, which follows the “ready” prompt or another prompt. • for certain operations, compound commands can be used. For example, instead of saying “setup” and then “pair a device,” the following compound command can be said: “pair a bluetooth d...

  • Page 119

    Pair (link) uconnect® phone to a mobile phone to begin using your uconnect® phone, you must pair your compatible bluetooth® enabled mobile phone. To complete the pairing process, you will need to refer- ence your mobile phone owner’s manual. The uconnect® website may also provide detailed instruc- t...

  • Page 120

    Present in the vehicle, the uconnect® phone will use the priority three mobile phone when you make a call. You can select to use a lower priority mobile phone at any time (refer to “advanced phone connectivity” in this section). Dial by saying a number • push the phone button to begin. • after the “...

  • Page 121

    Add names to your uconnect® phonebook note: adding names to the uconnect® phonebook is recommended when the vehicle is not in motion. To add names to the uconnect® phonebook using voice commands: 1. Push the phone button to begin. 2. After the “ready” prompt and the following beep, say “phonebook ne...

  • Page 122

    Phonebook download — automatic phonebook transfer from mobile phone if equipped and specifically supported by your phone, uconnect® phone automatically downloads names (text names) and number entries from your mobile phone’s phonebook. Specific bluetooth® phones with phone book access profile may su...

  • Page 123

    Edit uconnect® phonebook entries note: editing phonebook entries is recommended when the vehicle is not in motion. Automatic down- loaded phonebook entries cannot be deleted or edited. • push the phone button to begin. • after the “ready” prompt and the following beep, say “phonebook edit.” • you wi...

  • Page 124

    Delete uconnect® phonebook entry note: editing phonebook entries is recommended when the vehicle is not in motion. To delete a uconnect® phonebook entry using voice commands: 1. Push the phone button to begin. 2. After the “ready” prompt and the following beep, say “phonebook delete.” 3. After you e...

  • Page 125

    3. After confirmation, the phonebook entries will be deleted. Note: • only the phonebook in the current language is deleted. • automatic downloaded phonebook entries cannot be deleted or edited. List all names in the uconnect® phonebook to hear a list of all names in the uconnect® phonebook using vo...

  • Page 126

    Answer or reject an incoming call — no call currently in progress when you receive a call on your mobile phone, the uconnect® phone will interrupt the vehicle audio sys- tem, if on, and will ask if you would like to answer the call. • push the phone button to accept the call. • to reject the call, p...

  • Page 127

    Place/retrieve a call from hold to put a call on hold: 1. Push the phone button until you hear a single beep. • this indicates that the call is on hold. • to bring the call back from hold, push and hold the phone button until you hear a single beep. Toggling between calls if two calls are in progres...

  • Page 128

    Call termination to end a call in progress: 1. Momentarily push the phone button. • only the active call(s) will be terminated and if there is a call on hold, it will become the new active call. If the active call is terminated by the phone far end, a call on hold may not become active automatically...

  • Page 129

    2. After the ignition is cycled to off, a call can continue on the uconnect® phone for a certain duration, after which the call is automatically transferred from the uconnect® phone to the mobile phone. 3. An active call is automatically transferred to the mobile phone after the ignition is cycled t...

  • Page 130

    If the phone is not reachable and the uconnect® phone is operational, you may reach the emergency number as follows: • push the phone button to begin. • after the “ready” prompt and the following beep, say “emergency” and the uconnect® phone will instruct the paired mobile phone to call the emergenc...

  • Page 131

    Roadside assistance/towing assistance if you need roadside assistance: • push the phone button to begin. • after the “ready” prompt and the following beep, say “towing assistance.” note: you should program the desired towing assis- tance phone number using the voice command system. To do this, push ...

  • Page 132

    Required to enter your pin followed with a pound, (3 7 4 6 #), you can push the voice command button and say, “3 7 4 6 # send.” saying a number, or sequence of numbers, followed by “send,” is also to be used for navigating through an automated customer service center menu structure, and to leave a n...

  • Page 133

    Turning confirmation prompts on/off turning confirmation prompts off will stop the system from confirming your choices (e.G., the uconnect® phone will not repeat a phone number before you dial it). 1. Push the phone button to begin. 2. After the “ready” prompt and the following beep, say one of the ...

  • Page 134

    Mute/un-mute (mute on/off) when you mute the uconnect® phone, you will still be able to hear the conversation coming from the other party, but the other party will not be able to hear you. To mute the uconnect® phone: • push the voice command button. • following the beep, say “mute.” to un-mute the ...

  • Page 135

    List paired mobile phone names • push the phone button to begin. • after the “ready” prompt and the following beep, say “setup phone pairing.” • when prompted, say “list phones.” • the uconnect® phone will play the phone names of all paired mobile phones in order from the highest to the lowest prior...

  • Page 136

    Delete uconnect® phone paired mobile phones to delete mobile phones paired with the uconnect® phone using voice commands: 1. Push the phone button to begin. 2. After the “ready” prompt and the following beep, say “setup phone pairing.” 3. At the next prompt, say “delete” and follow the prompts. • yo...

  • Page 137

    Best results, the voice training session should be com- pleted when the vehicle is parked with the engine running, all windows closed, and the blower fan switched off. This procedure may be repeated with a new user. The system will adapt to the last trained voice only. Reset to reset all settings us...

  • Page 138

    • smooth road surface • fully closed windows • dry weather condition note: • even though the system is designed for users speaking in north american english, french, and spanish ac- cents, the system may not always work for some. • when navigating through an automated system such as voice mail, or w...

  • Page 139

    • fully closed windows • dry weather conditions • operation from the driver’s seat • performance, such as audio clarity, echo, and loudness to a large degree rely on the phone and network, and not the uconnect® phone • echo at the phone far end can sometimes be reduced by lowering the in-vehicle aud...

  • Page 140

    Send messages: you can send messages using uconnect® phone. To send a new message: 1. Push the phone button. 2. After the “ready” prompt and the following beep, say “sms send” or “send message.” 3. You can either say the message you wish to send or say “list messages.” there are 20 preset messages. ...

  • Page 141

    12. I am on my way. 13. I’ll be late. 14. Are you there yet? 15. Where are we meeting? 16. Can this wait? 17. Bye for now. 18. When can we meet? 19. Send number to call. 20. Start without me. Turn voice text reply incoming announcement on/ off turning the voice text reply incoming announcement off w...

  • Page 142

    140 understanding the features of your vehicle.

  • Page 143

    3 understanding the features of your vehicle 141.

  • Page 144

    142 understanding the features of your vehicle.

  • Page 145

    Voice commands primary alternate (s) zero one two three four five six seven eight nine star (*) plus (+) pound (#) add location primary alternate (s) all call cancel confirmation prompts continue delete dial download edit emergency english erase all espanol francais help 3 understanding the features...

  • Page 146

    Primary alternate (s) home language list names list phones mobile mute mute off new entry no other pair a phone phone pairing pairing phonebook phone book previous record again primary alternate (s) redial return to main menu return or main menu select phone select send set up phone settings or phon...

  • Page 147

    General information this device complies with part 15 of the fcc rules and rss 210 of industry canada. Operation is subject to the following conditions: • changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment....

  • Page 148

    Warning! Any voice commanded system should be used only in safe driving conditions following all applicable laws, including laws regarding phone use. Your at- tention should be focused on safely operating the vehicle. Failure to do so may result in a collision causing serious injury or death. When y...

  • Page 149

    To hear the first available menu, push the voice com- mand button and say “help” or “main menu.” commands the voice command system understands two types of commands, universal commands and local commands. Universal commands are available at all times. Local commands are available if the supported ra...

  • Page 150

    Radio am to switch to the am band, say “am” or “radio am.” in this mode, you may say the following commands: • “frequency #” (to change the frequency) • “next station” (to select the next station) • “previous station” (to select the previous station) • “radio menu” (to switch to the radio menu) • “m...

  • Page 151

    Disc mode to switch to the disc mode, say “disc.” in this mode, you may say the following commands: • “track” (#) (to change the track) • “next track” (to play the next track) • “previous track” (to play the previous track) • “main menu” (to switch to the main menu) usb mode to switch to usb mode, s...

  • Page 152

    – “save” (to save the memo) – “continue” (to continue recording) – “delete” (to delete the recording) • “play memos” (to play previously recorded memos) — during the playback you may push the voice com- mand button to stop playing memos. You pro- ceed by saying one of the following commands: – “repe...

  • Page 153

    Note: keep in mind that you have to push the voice command button first and wait for the beep before speaking the “barge in” commands. Voice training for users experiencing difficulty with the system recog- nizing their voice commands or numbers the uconnect® voice “voice training” feature may be us...

  • Page 154

    Warning! (continued) • be sure everyone in your vehicle is in a seat and using a seat belt properly. Power seats — if equipped some models may be equipped with a power driver’s seat. The power seat switch is located on the outboard side of the seat near the floor. Use the switch to move the seat up,...

  • Page 155

    Warning! • adjusting a seat while driving may be dangerous. Moving a seat while driving could result in loss of control which could cause a collision and serious injury or death. • seats should be adjusted before fastening the seat belts and while the vehicle is parked. Serious injury or death could...

  • Page 156

    Heated seats — if equipped on some models, the front driver and passenger seats may be equipped with heaters in both the seat cushions and seatbacks. The controls for the front heated seats are located on the center instrument panel area. You can choose from hi, lo or off heat settings. Amber indica...

  • Page 157

    Warning! (continued) • do not place anything on the seat or seatback that insulates against heat, such as a blanket or cushion. This may cause the seat heater to overheat. Sitting in a seat that has been overheated could cause serious burns due to the increased surface tempera- ture of the seat. Man...

  • Page 158

    Warning! • adjusting a seat while driving may be dangerous. Moving a seat while driving could result in loss of control which could cause a collision and serious injury or death. • seats should be adjusted before fastening the seat belts and while the vehicle is parked. Serious injury or death could...

  • Page 159

    Manual lumbar — if equipped the lumbar adjustment handle is located on the inboard or outboard side of the seatback. Rotate the lever down- ward to increase the lumbar support or rotate the lever upward to decrease the lumbar support. Driver’s seatback recline to adjust the seatback, lift the lever ...

  • Page 160

    Warning! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt, which could result in serious injury or death. Head restraints head restraints are designed to reduce the risk of injury by restricti...

  • Page 161

    When ahrs deploy during a rear impact, the front half of the head restraint extends forward to minimize the gap between the back of the occupant’s head and the ahr. This system is designed to help prevent or reduce the extent of injuries to the driver and front passenger in certain types of rear imp...

  • Page 162

    Active head restraint (normal position) active head restraint (tilted position) 160 understanding the features of your vehicle.

  • Page 163

    Note: • the head restraints should only be removed by quali- fied technicians, for service purposes only. If either of the head restraints require removal, see your autho- rized dealer. • in the event of deployment of an active head re- straint, refer to “occupant restraints/resetting active head re...

  • Page 164

    Rear head restraints the head restraints in the rear are non adjustable. Refer to “occupant restraints” in “things to know before start- ing your vehicle” for information on tether routing. Folding rear seat to provide additional storage area, each rear seatback can be folded forward. Pull the strap...

  • Page 165

    To raise the seatback, pull the strap forward and lift the seatback into its upright position. Warning! Be certain that the seatback is securely locked into position. If the seatback is not securely locked into position the seat will not provide the proper stability for child seats and/or passengers...

  • Page 166

    Reclining rear seat — if equipped for additional comfort, pull the strap forward just enough to release the seatback latch. Then push the seatback to a reclined position, approximately 35 degrees maximum, and release the strap. Warning! Do not ride with the seatback reclined so that the shoulder bel...

  • Page 167

    2. Move the safety catch located under the front edge of the hood, near the center and raise the hood. Lift the hood prop rod, clipped to the right side (left side facing hood) of the engine compartment, to secure the hood in the open position. Place the hood prop at the location stamped into the in...

  • Page 168

    Caution! To prevent possible damage: • before closing hood, make sure the hood prop rod is fully seated into its storage retaining clips. • do not slam the hood to close it. Use a firm downward push at the center front edge of the hood to ensure that both latches engage. Never drive your vehicle unl...

  • Page 169

    Lights multifunction lever the multifunction lever controls the operation of the headlights, parking lights, turn signals, headlight beam selection, instrument panel light dimming, interior lights, the passing lights, and the fog lights. The multifunction lever is located on the left side of the ste...

  • Page 170

    Headlights and parking lights turn the end of the multifunction lever to the first detent to turn on the parking lights. Turn the end of the lever to the second detent to turn on the headlights. Daytime running lights — if equipped the high beam lights will come on as daytime running lights (lower i...

  • Page 171

    Note: the fog lights will only operate with the head- lights on low beam. Selecting high beam headlights will turn off the fog lights. Turn signals move the multifunction lever up or down and the arrows on each side of the instrument cluster flash to show proper operation of the front and rear turn ...

  • Page 172

    Note: if either light remains on and does not flash, or there is a very fast flash rate, check for a defective outside light bulb. If an indicator fails to light when the lever is moved, it would suggest that the indicator bulb is defective. Lane change assist tap the lever up or down once, without ...

  • Page 173

    Rotate the center portion of the lever up to increase the brightness of the instrument panel lights when the park- ing lights or headlights are on. Rotate the center portion of the lever upward to the next detent position to brighten the odometer and radio when the parking lights or headlights are o...

  • Page 174

    Light off. The lights also come on when a door is opened or the dimmer control is turned fully upward, past the second detent. Note: the lights will remain on until the switch is pushed a second time, so be sure they have been turned off before leaving the vehicle. They will not turn off automatical...

  • Page 175

    Caution! • turn the windshield wipers off when driving through an automatic car wash. Damage to the windshield wipers may result if the wiper control is left in any position other than off. • in cold weather, always turn off the wiper switch and allow the wipers to return to the “park” posi- tion be...

  • Page 176

    Windshield wiper operation rotate the end of the lever upward to the second detent past the intermittent settings for low-speed wiper opera- tion. Rotate the end of the lever upward to the third detent past the intermittent settings for high-speed wiper operation. Intermittent wiper system use the i...

  • Page 177

    Windshield washers to use the washer, pull the control lever toward you and hold while spray is desired. If the lever is pulled while in the delay range, the wiper will operate in low-speed while the lever is pulled and for two wipe cycles after the lever is released, and then resume the intermitten...

  • Page 178

    Note: the mist feature does not activate the washer pump; therefore, no washer fluid will be sprayed on the windshield. The wash function must be used in order to spray the windshield with washer fluid. Tilt steering column this feature allows you to tilt the steering column upward or downward. The ...

  • Page 179

    Warning! Do not adjust the steering column while driving. Adjusting the steering column while driving or driv- ing with the steering column unlocked, could cause the driver to lose control of the vehicle. Failure to follow this warning may result in serious injury or death. Electronic speed control ...

  • Page 180

    Note: in order to ensure proper operation, the elec- tronic speed control system has been designed to shut down if multiple speed control functions are operated at the same time. If this occurs, the electronic speed control system can be reactivated by pushing the electronic speed control on/off but...

  • Page 181

    Warning! Leaving the electronic speed control system on when not in use is dangerous. You could accidentally set the system or cause it to go faster than you want. You could lose control and have an accident. Always leave the system off when you are not using it. To set a desired speed turn the elec...

  • Page 182

    To vary the speed setting to increase speed when the electronic speed control is set, you can in- crease speed by pushing the res (+) button. The drivers preferred units can be selected through the instrument panel settings if equipped. Refer to “under- standing your instrument panel” for more infor...

  • Page 183

    The drivers preferred units can be selected through the instrument panel settings if equipped. Refer to “under- standing your instrument panel” for more information. The speed decrement shown is dependant on the chosen speed unit of u.S. (mph) or metric (km/h): u.S. Speed (mph) • pushing the set (-)...

  • Page 184

    Warning! Electronic speed control can be dangerous where the system cannot maintain a constant speed. Your ve- hicle could go too fast for the conditions, and you could lose control and have an accident. Do not use electronic speed control in heavy traffic or on roads that are winding, icy, snow-cov...

  • Page 185

    Homelink® buttons/sunvisor/headliner note: homelink® is disabled when the vehicle secu- rity alarm is active. Before you begin programming homelink® be sure that your vehicle is parked outside of the garage before you begin programming. For more efficient programming and accurate transmis- sion of t...

  • Page 186

    Programming a rolling code for programming garage door openers that were manu- factured after 1995. These garage door openers can be identified by the “learn” or “train” button located where the hanging antenna is attached to the garage door opener. It is not the button that is normally used to open...

  • Page 187

    2. Place the hand-held transmitter 1 to 3 inches (3 to 8 cm) away from the homelink® button you wish to program while keeping the homelink® indicator light in view. 3. Push and hold the homelink® button you want to program while you push and hold the hand-held transmitter button. 4. Continue to hold...

  • Page 188

    Reprogramming a single homelink® button (rolling code) to reprogram a channel that has been previously trained, follow these steps: 1. Cycle the ignition to the on/run position. 2. Push and hold the desired homelink® button until the indicator light begins to flash after 20 seconds. Do not release t...

  • Page 189

    • to program the two remaining homelink® buttons, repeat each step for each remaining button. Do not erase the channels. Reprogramming a single homelink® button (non-rolling code) to reprogram a channel that has been previously trained, follow these steps: 1. Cycle the ignition to the on/run positio...

  • Page 190

    2. Place the hand-held transmitter 1 to 3 inches (3 to 8 cm) away from the homelink® button you wish to program while keeping the homelink® indicator light in view. 3. Continue to push and hold the homelink® button, while you push and release (“cycle”) your hand-held transmitter every two seconds un...

  • Page 191

    3. Without releasing the button proceed with “canadian/gate operator programming” step 2 and follow all remaining steps. Using homelink® to operate, push and release the programmed homelink® button. Activation will now occur for the programmed device (i.E., garage door opener, gate opera- tor, secur...

  • Page 192

    Warning! • vehicle exhaust contains carbon monoxide, a dan- gerous gas. Do not run your vehicle in the garage while programming the transceiver. Exhaust gas can cause serious injury or death. • your motorized door or gate will open and close while you are programming the universal trans- ceiver. Do ...

  • Page 193

    Note: • the transmitter has been tested and it complies with fcc and ic rules. Changes or modifications not ex- pressly approved by the party responsible for compli- ance could void the user’s authority to operate the device. • the term ic before the certification/registration num- ber only signifie...

  • Page 194

    Warning! • never leave children alone in a vehicle, or with access to an unlocked vehicle. Never leave the key fob in or near the vehicle, or in a location acces- sible to children. Occupants, particularly unat- tended children, can become entrapped by the power sunroof while operating the power sun...

  • Page 195

    Position. The sunroof will close fully and stop automati- cally. This is called “express close”. During express close operation, any movement of the switch will stop the sunroof. Closing sunroof — manual mode to close the sunroof, push and hold the switch in the forward position. Any release of the ...

  • Page 196

    Open or partially open positions. This is a normal occur- rence and can be minimized. If the buffeting occurs with the rear windows open, open the front and rear windows together to minimize the buffeting. If the buffeting occurs with the sunroof open, adjust the sunroof opening to minimize the buff...

  • Page 197

    Power is available when the ignition switch is in the on or acc position. Insert the cigar lighter or accessory plug into the outlet for use. To preserve the heating element, do not hold the lighter in the heating position. Note: to ensure proper operation a mopar® knob and element must be used. Cau...

  • Page 198

    Warning! To avoid serious injury or death: • only devices designed for use in this type of outlet should be inserted into any 12 volt outlet. (continued) warning! (continued) • do not touch with wet hands. • close the lid when not in use and while driving the vehicle. • if this outlet is mishandled,...

  • Page 199

    Caution! (continued) • accessories that draw higher power (i.E., coolers, vacuum cleaners, lights, etc.) will degrade the bat- tery even more quickly. Only use these intermit- tently and with great caution. • after the use of high power draw accessories, or long periods of the vehicle not being star...

  • Page 200

    Warning! To avoid serious injury or death: • do not use a three-prong adaptor. • do not insert any objects into the receptacles. • do not touch with wet hands. • close the lid when not in use. • if this outlet is mishandled, it may cause an electric shock and failure. Caution! • many accessories tha...

  • Page 201

    Caution! (continued) • accessories that draw higher power (i.E., coolers, vacuum cleaners, lights, etc.) will degrade the bat- tery even more quickly. Only use these intermit- tently and with great caution. • after the use of high power draw accessories, or long periods of the vehicle not being star...

  • Page 202

    There are two cupholders located in the back for the rear passengers. Storage glove compartment and storage bin located on the passenger side of the instrument panel are an upper storage bin and a lower glove compartment. Rear cupholders storage bins 1 — upper storage bin 2 — lower glove compartment...

  • Page 203

    To open the lower glove compartment, pull outward on the release handle. Door storage the interior door panels are equipped with lower storage areas. Glove compartment front door storage 3 understanding the features of your vehicle 201.

  • Page 204

    Console features the floor console contains both an upper and lower storage compartment. To open the upper storage compartment, push inward on the upper handle to unlatch the upper lid and lift the lid open. To open the lower storage compartment, lift upward on the lower handle to unlatch the lower ...

  • Page 205

    Warning! Do not operate this vehicle with a console compart- ment lid in the open position. Driving with the console compartment lid open may result in injury in a collision. Cargo area features cargo light the light is mounted in the headliner above the cargo area to illuminate the cargo area. Carg...

  • Page 206

    Using the handle, pull the cover toward you and guide the rear cover posts into the guides located on both sides of the rear trim panel. Rear trim notches cargo cover guides 204 understanding the features of your vehicle.

  • Page 207

    Warning! In a collision a cargo cover loose in the vehicle could cause injury. It could fly around in a sudden stop and strike someone in the vehicle. Do not store the cargo cover on the cargo floor or in the passenger compart- ment. Remove the cover from the vehicle when taken from its mounting. Do...

  • Page 208

    Cargo tie-down loops there are four tie-downs (d-rings) installed in the cargo area for securing cargo. Warning! • cargo tie-down loops are not safe anchors for a child seat tether strap. In a sudden stop or collision a loop could pull loose and allow the child seat to come loose. A child could be b...

  • Page 209

    Warning! (continued) • place as much cargo as possible in front of the rear axle. Too much weight or improperly placed weight over or behind the rear axle can cause the rear of the vehicle to sway. • do not pile luggage or cargo higher than the top of the seatback. This could impair visibility or be...

  • Page 210

    Rear window features rear window wiper/washer the rear wiper/washer is controlled by a rotary switch located on the center portion of the control lever. The control lever is located on the right side of the steering column. Rotate the center portion of the lever upward to the first detent position f...

  • Page 211

    Note: the rear wiper operates in an intermittent mode only. Rotate the center portion of the lever past the first detent to activate the rear washer. The washer pump and the wiper will continue to operate as long as the switch is held (for a maximum of 10 seconds). Upon release, the wiper will conti...

  • Page 212

    Caution! Failure to follow these cautions can cause damage to the heating elements: • use care when washing the inside of the rear window. Do not use abrasive window cleaners on the interior surface of the window. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements....

  • Page 213

    The crossbars must also be secured in one of the seven detent positions marked with an arrow on the siderails to prevent movement. To move the crossbars, loosen the thumb screws located at the upper edge of each crossbar approximately eight turns, then move the crossbar to the desired position, keep...

  • Page 214

    Caution! (continued) • long loads which extend over the windshield, such as wood panels or surfboards, or loads with large frontal area should be secured to both the front and rear of the vehicle. • travel at reduced speeds and turn corners carefully when carrying large or heavy loads on the roof ra...

  • Page 215: Contents

    Understanding your instrument panel contents ! Instrument panel features . . . . . . . . . .216 ! Instrument cluster . . . . . . . . . . . . . . . . .217 ! Instrument cluster descriptions . . . . .218 ! Mini-trip computer — if equipped . . . . .232 ▫ control buttons . . . . . . . . . . . . . . . . ....

  • Page 216

    ▫ operating instructions — radio mode. . . . . . .246 ▫ operation instructions — disc mode for cd and mp3/wma audio play, dvd – video . . . . . . .255 ▫ notes on playing mp3/wma files. . . . . . . . .257 ▫ list button — disc mode for mp3/wma play . . . . . . . . . . . . . . . . . . . . . . . . . . ....

  • Page 217

    ! Ipod®/usb/mp3 control — if equipped . .293 ▫ connecting the ipod® or external usb device . . . . . . . . . . . . . . . . . . . . . . . . . . . . .293 ▫ using this feature. . . . . . . . . . . . . . . . . . . . .294 ▫ controlling the ipod® or external usb device using radio buttons . . . . . . . . ...

  • Page 218

    Instrument panel features 1 — air outlet 5 — storage bin 9 — heated seat switch – if equipped 2 — demisters 6 — glove compartment 10 — hazard warning flasher 3 — instrument cluster 7 — climate controls 11 — esc off switch – if equipped 4 — radio 8 — power outlet 12 — heated seat switch – if equipped...

  • Page 219

    Instrument cluster 4 understanding your instrument panel 217.

  • Page 220

    Instrument cluster descriptions 1. Fuel gauge/fuel door reminder when the ignition switch is in the on/run position, the pointer will show the level of fuel remaining in the fuel tank. The fuel pump symbol points to the side of the vehicle where the fuel door is located. 2. Charging system light thi...

  • Page 221

    On briefly as a bulb check. If the light does not come on during starting, have the system checked by an autho- rized dealer. 4. Oil pressure warning light this light indicates low engine oil pressure. The light should turn on momentarily when the engine is started. If the light turns on while drivi...

  • Page 222

    Note: if either indicator flashes at a rapid rate, check for a defective outside light bulb. 9. High beam indicator this indicator shows that the high beam head- lights are on. Push the multifunction lever for- ward to switch the headlights to high beam and pull toward yourself (normal position) to ...

  • Page 223

    12. Tachometer the white area of the scale shows the permissible engine revolutions-per-minute (rpm x 1000) for each gear range. Before reaching the red area, ease up on the accelerator to prevent engine damage. 13. Engine temperature warning light this light warns of an overheated engine condition....

  • Page 224

    Booster, the abs pump will run when applying the brake, and a brake pedal pulsation may be felt during each stop. The dual brake system provides a reserve braking capac- ity in the event of a failure to a portion of the hydraulic system. A leak in either half of the dual brake system is indicated by...

  • Page 225

    The light also will turn on when the parking brake is applied with the ignition switch in the on/run posi- tion. Note: this light shows only that the parking brake is applied. It does not show the degree of brake application. 15. Transmission temperature warning light this light indicates that the t...

  • Page 226

    17. Temperature gauge the temperature gauge shows engine coolant tempera- ture. Any reading within the normal range indicates that the engine cooling system is operating satisfactorily. The gauge pointer will likely indicate a higher tempera- ture when driving in hot weather, up mountain grades, or ...

  • Page 227

    19. 4wd indicator light this light indicates the vehicle is in 4wd locked mode. 20. Shift lever indicator the shift lever indicator is self-contained within the instrument cluster. It displays the gear position of the automatic transmission. Note: you must apply the brakes before shifting from park....

  • Page 228

    Accordingly, when the low tire pressure telltale illumi- nates, you should stop and check your tires as soon as possible, and inflate them to the proper pressure. Driving on a significantly under-inflated tire causes the tire to overheat and can lead to tire failure. Under-inflation also reduces fue...

  • Page 229

    Caution! (continued) equipped on your vehicle. Undesirable system opera- tion or sensor damage may result when using re- placement equipment that is not of the same size, type, and/or style. Aftermarket wheels can cause sensor damage. Using aftermarket tire sealants may cause the tire pressure monit...

  • Page 230

    Gate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Gate ajar gascap . . . . . . . . . . . . . . . . . . . . . . Fuel cap fault low tire . . . . . . . . . . . . . . . . . . . . Low tire pressure change oil . . . . . . . . . . . . . . Oil change required note: if the vehicle is equipped wi...

  • Page 231

    Position. To turn off the message temporarily, push and release the trip odometer button on the instrument cluster. To reset the oil change indicator system (after performing the scheduled maintenance), refer to the following procedure: 1. Turn the ignition switch to the on/run position. Do not star...

  • Page 232

    Caution! Prolonged driving with the malfunction indicator light (mil) on could cause damage to the engine control system. It also could affect fuel economy and driveability. If the mil is flashing, severe catalytic converter damage and power loss will soon occur. Immediate service is required. Warni...

  • Page 233

    29. Electronic stability control (esc) activation/ malfunction indicator light — if equipped the “esc activation/malfunction indicator light” in the instrument cluster will come on when the ignition switch is turned to the on/run position. It should go out with the engine running. If the “esc activa...

  • Page 234

    Check, when the ignition key is turned to the on/run position and may stay on for as long as three seconds. When lit solid: there is a 4wd system fault. 4wd performance will be at a reduced level. Service the 4wd system soon. When blinking: the 4wd system is temporarily dis- abled due to overload co...

  • Page 235

    Control buttons step button push the step button located on the steering wheel to scroll through sub menus (i.E., temperature, trip func- tions: odometer, trip a, trip b). Reset button to reset the display shown, turn the ignition switch to the on position, then push and hold the reset button locate...

  • Page 236

    Trip b shows the total distance traveled for trip b since the last reset. Electronic vehicle information center (evic) — if equipped the electronic vehicle information center (evic) fea- tures a driver-interactive display that is located in the instrument cluster. The evic consists of the following:...

  • Page 237

    • personal settings (customer-programmable features) • compass heading • outside temperature display • trip computer functions • uconnect® phone displays (if equipped) • audio mode display • tire pressure monitor (tpm) the system allows the driver to select information by pushing the following butto...

  • Page 238

    Menu button push and release the menu button to scroll through the main menus (fuel economy, warn- ings, timer, units, system, personal settings) or to exit submenus. Compass button push and release the compass button to display one of eight compass readings and the outside temperature or to exit su...

  • Page 239

    • personal settings not avail. — vehicle is not in park (automatic transmission), or vehicle is in motion (manual transmission). • door ajar (with vehicle graphic showing which door is open. A single chime sounds if the vehicle is in motion). • doors ajar (with vehicle graphic showing which doors ar...

  • Page 240

    Indicator system is duty-cycle based, which means the engine oil change interval may fluctuate dependent upon your personal driving style. Unless reset, this message will continue to display each time you turn the ignition switch to the on/run position. To turn off the message temporarily, push and ...

  • Page 241

    Reset will only occur if a resettable function is currently being displayed. To reset all resettable functions, push and release the right/select arrow button a second time within three seconds of resetting the currently displayed function. Reset all will be displayed during this three-second window...

  • Page 242

    # low fuel # text and a new dte value will be dis- played, based on the current values in the dte calcula- tion and the current fuel tank level. Tire pressure monitor (tpm) refer to “tire pressure monitoring system (tpms)” in “starting and operating” for system operation. Elapsed time shows the tota...

  • Page 243

    Use the select button to display one of the following choices: language when in this display, you may select different languages for all display nomenclature, including the trip functions. Pushing the right/select button while in this display selects english, espanol, deutsch, italiano, francais, or...

  • Page 244

    Button. Push and hold the right arrow button when in this display until “driver’s door 1st” or “all doors” appears to make your selection. Flash lamps with lock when on is selected, the front and rear turn signals will flash when the doors are locked or unlocked using the rke transmitter. This featu...

  • Page 245

    Illuminated approach when this feature is selected, the headlights will activate and remain on for up to 90 seconds when the doors are unlocked using the rke transmitter. Push and hold the right arrow button when in this display until “off,” “30 sec,” “60 sec,” or “90 sec.” appears to make your sele...

  • Page 246

    Manual compass calibration if the compass appears erratic and the “cal” indicator does not appear in the evic display, you must put the compass into the calibration mode manually as follows: 1. Start the engine. Leave the shift lever in park in order to enter the evic programming menus. 2. Push and ...

  • Page 247

    1. Turn the ignition switch on. 2. Push and hold the compass button for approxi- mately two seconds. 3. Push and release the down button until “compass variance” message and the last variance zone number displays in the evic. 4. Push and release the select button until the proper variance zone is se...

  • Page 248

    Uconnect® 230 – am/fm stereo radio and 6–disc cd/dvd changer (mp3/wma aux jack) operating instructions — radio mode note: the ignition switch must be in the on or acc position to operate the radio. Power switch/volume control (rotary) push the on/volume control knob to turn on the radio. Push the on...

  • Page 249

    Seek buttons push and release the seek buttons to search for the next listenable station in am/fm mode. Push the right switch to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection. Holding either button will bypass stations witho...

  • Page 250

    Time button push the time button to alternate locations of the time and frequency display. Clock setting procedure 1. Push and hold the time button until the hours blink. 2. Adjust the hours by turning the right side tune/ scroll control knob. 3. After adjusting the hours, push the right side tune/ ...

  • Page 251

    Setting the tone, balance and fade push the rotary tune/scroll control knob and bass will display. Turn the tune/scroll control knob to the right or left to increase or decrease the bass tones. Push the rotary tune/scroll control knob a second time and mid will display. Turn the tune/scroll control ...

  • Page 252

    Toggle the music type button to select the following format types: program type 16-digit character dis- play no program type or un- defined none adult hits adlt hit classical classicl classic rock cls rock college college country country foreign language language information inform jazz jazz news ne...

  • Page 253

    By pushing the seek button when the music type icon is displayed, the radio will be tuned to the next frequency station with the same selected music type name. The music type function only operates when in the fm mode. If a preset button is activated while in the music type (program type) mode, the ...

  • Page 254

    • angle — repeatedly pushing select will change the viewing angle if supported by the dvd disc (if equipped). Note: • the available selections for each of the above entries varies depending upon the disc. • these selections can only be made while playing a dvd. • power — allows you to turn the power...

  • Page 255

    Audio language — if equipped selecting this item allows you to choose a default audio language (effective only if the language is supported by the disc). You can select a language not listed by scrolling down and selecting # other. # enter the country code using the tune/scroll control knob to scrol...

  • Page 256

    Note: the user will have to set these defaults before loading a disc. If changes are made to these settings after a disc is loaded, changes will not be effective. Also, the defaults are effective only if the disc supports the customer-preferred settings. Am and fm buttons push the buttons to select ...

  • Page 257

    Disc button pushing the disc button will allow you to switch from am/fm modes to disc modes. Operation instructions — disc mode for cd and mp3/wma audio play, dvd – video the radio dvd player and many dvd discs are coded by geographic region. These region codes must match for the disc to play. If th...

  • Page 258

    Caution! This cd player will accept 4–3/4 inch (12 cm) discs only. The use of other sized discs may damage the cd player mechanism. Eject button — ejecting compact disc(s) push the eject button and the pushbutton with the corresponding number (1-6) where the cd was loaded and the disc will unload an...

  • Page 259

    Rw/ff (cd mode) push and hold ff (fast forward) and the cd player will begin to fast forward until ff is released, or rw or another cd button is pushed. The rw (rewind) button works in a similar manner. Am or fm button (cd mode) switches the radio into the am or fm radio mode. Notes on playing mp3/w...

  • Page 260

    Multisession disc formats are supported by the radio. Multisession discs may contain combinations of normal cd audio tracks and computer files (including mp3/ wma files). Discs created with an option such as # keep disc open after writing # are most likely multisession discs. The use of multisession...

  • Page 261

    Wma specification sampling frequency (khz) bit rate (kbps) wma 44.1 and 48 48, 64, 96, 128, 160, 192 vbr id3 tag information for artist, song title, and album title are supported for id3 version 1 tags. Id3 version 2 is not supported by the radios. Playlist files are not supported. Mp3 pro files are...

  • Page 262

    List button — disc mode for mp3/wma play pushing the list button will bring up a list of all folders on the disc. Scrolling up or down the list is done by turning the tune/scroll control knob. Selecting a folder by pushing the tune/scroll control knob will begin playing the files contained in that f...

  • Page 263

    Scan button (auxiliary mode) no function. Eject button (auxiliary mode) no function. Time button (auxiliary mode) push the time button to change the display from elapsed playing time to time of day. The time of day will display for five seconds. Rw/ff (auxiliary mode) no function. Set button (auxili...

  • Page 264

    Intended for home and other limited viewing uses only, unless otherwise authorized by macrovision. Reverse engineering or disassembly is prohibited. Dts™ “dts™ and “dts™ 2.0” are trademarks of digital the- ater systems, inc. Uconnect® (satellite radio) — if equipped satellite radio uses direct satel...

  • Page 265

    To access the esn/sid, refer to the following steps: esn/sid access with the ignition switch in the on/run or acc posi- tion and the radio on, push the setup button and scroll using the tune/scroll control knob until sirius id is selected. Push the tune/scroll control knob and the sirius id number w...

  • Page 266

    Operating instructions — uconnect® (satellite) mode note: the ignition switch must be in the on/run or acc position to operate the radio. Seek buttons push and release the seek buttons to search for the next listenable station in am/fm mode. Push the right switch to seek up and the left switch to se...

  • Page 267

    Music type button pushing this button once will turn on the music type mode for five seconds. Pushing the music type button or turning the tune/scroll control knob within five seconds will allow the program format type to be se- lected. Toggle the music type button again to select the music type. By...

  • Page 268

    You may add a second channel to each pushbutton by repeating the above procedure with this exception: push the set button twice and set 2 will show in the display window. Each button can be set for set 1 and set 2. This allows a total of 12 satellite channels to be stored into pushbutton memory. The...

  • Page 269

    Uconnect® 130 operating instructions — radio mode note: the ignition switch must be in the on or acc position to operate the radio. Power switch/volume control (rotary) push the on/volume control knob to turn on the radio. Push the on/volume control knob a second time to turn off the radio. Electron...

  • Page 270

    Another selection. Holding either button will bypass stations without stopping, until you release it. Time button push the time button to alternate display of the time and radio frequency. Clock setting procedure 1. Push and hold the time button until the hours blink. 2. Adjust the hours by turning ...

  • Page 271

    Push the rotary tune/scroll control knob a second time and mid will display. Turn the tune/scroll control knob to the right or left to increase or decrease the mid-range tones. Push the rotary tune/scroll control knob a third time and treble will display. Turn the tune/scroll control knob to the rig...

  • Page 272

    Display window. Each button can be set for set 1 and set 2 in both am and fm. This allows a total of 12 am and 12 fm stations to be stored into pushbutton memory. The stations stored in set 2 memory can be selected by pushing the pushbutton twice. Every time a preset button is used, a corresponding ...

  • Page 273

    If you insert a disc with the ignition on and the radio on, the unit will switch from radio to cd mode and begin to play when you insert the disc. The display will show the track number, and index time in minutes and seconds. Play will begin at the start of track 1. Caution! • this cd player will ac...

  • Page 274

    Seek button push the right seek button for the next selection on the cd. Push the left seek button to return to the beginning of the current selection, or return to the beginning of the previous selection if the cd is within the first second of the current selection. Pushing and holding the seek but...

  • Page 275

    Supported media (disc types) the mp3 file recording media supported by the radio are cdda, cd-r, cd-rw, mp3, and cdda+mp3. Supported medium formats (file systems) the medium formats supported by the radio are iso 9660 level 1 and level 2 and includes the joliet extension. When reading discs recorded...

  • Page 276

    Supported mp3 file formats the radio will recognize only files with the *.Mp3 exten- sion as mp3 files. Non-mp3 files named with the *.Mp3 extension may cause playback problems. The radio is designed to recognize the file as an invalid mp3 and will not play the file. When using the mp3 encoder to co...

  • Page 277

    Playback of mp3 files when a medium containing mp3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the mp3 files. Loading times for playback of mp3 files may be affected by the following: • med...

  • Page 278

    Time button (auxiliary mode) push this button to change the display to time of day. The time of day will display for five seconds (when ignition is off). Uconnect® 130 with satellite radio operating instructions — radio mode note: the ignition switch must be in the on or acc position to operate the ...

  • Page 279

    Seek buttons push and release the seek buttons to search for the next listenable station in am/fm mode. Push the right switch to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection. Holding either button will bypass stations witho...

  • Page 280

    Clock setting procedure 1. Push and hold the time button until the hours blink. 2. Adjust the hours by turning the right side tune/ scroll control knob. 3. After adjusting the hours, push the right side tune/ scroll control knob to set the minutes. The minutes will begin to blink. 4. Adjust the minu...

  • Page 281

    Setting the tone, balance and fade push the rotary tune/scroll control knob and bass will display. Turn the tune/scroll control knob to the right or left to increase or decrease the bass tones. Push the rotary tune/scroll control knob a second time and mid will display. Turn the tune/scroll control ...

  • Page 282

    Toggle the music type button to select the following format types: program type 16-digit character dis- play no program type or un- defined none adult hits adlt hit classical classicl classic rock cls rock college college country country foreign language language information inform jazz jazz news ne...

  • Page 283

    By pushing the seek button when the music type icon is displayed, the radio will be tuned to the next frequency station with the same selected music type name. The music type function only operates when in the fm mode. If a preset button is activated while in the music type (program type) mode, the ...

  • Page 284

    You may add a second station to each pushbutton by repeating the above procedure with this exception: push the set/rnd button twice and set 2 will show in the display window. Each button can be set for set 1 and set 2 in both am and fm. This allows a total of 12 am and 12 fm stations to be stored in...

  • Page 285

    If you insert a disc with the ignition on and the radio on, the unit will switch from radio to cd mode and begin to play when you insert the disc. The display will show the track number, and index time in minutes and seconds. Play will begin at the start of track 1. Caution! • this cd player will ac...

  • Page 286

    Seek button push the right seek button for the next selection on the cd. Push the left seek button to return to the beginning of the current selection, or return to the beginning of the previous selection if the cd is within the first second of the current selection. Pushing and holding the seek but...

  • Page 287

    Supported media (disc types) the mp3 file recording media supported by the radio are cdda, cd-r, cd-rw, mp3, and cdda+mp3. Supported medium formats (file systems) the medium formats supported by the radio are iso 9660 level 1 and level 2 and includes the joliet extension. When reading discs recorded...

  • Page 288

    Supported mp3 file formats the radio will recognize only files with the *.Mp3 exten- sion as mp3 files. Non-mp3 files named with the *.Mp3 extension may cause playback problems. The radio is designed to recognize the file as an invalid mp3 and will not play the file. When using the mp3 encoder to co...

  • Page 289

    Playback of mp3 files when a medium containing mp3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the mp3 files. Loading times for playback of mp3 files may be affected by the following: • med...

  • Page 290

    Push the info button once more to return to # elapsed time # priority mode. Push and hold the info button for three seconds or more and the radio will display song titles for each file. Push and hold the info button again for three seconds to return to # elapsed time # display. Operation instruction...

  • Page 291

    Note: sirius service is not available in hawaii and has limited coverage in alaska. System activation sirius satellite radio service is pre-activated, and you may begin listening immediately to the one year of audio service that is included with the factory-installed satellite radio system in your v...

  • Page 292

    Selecting uconnect® (satellite) mode push the sat button until # sat # appears in the display. A cd may remain in the radio while in the satellite radio mode. Satellite antenna to ensure optimum reception, do not place items on the roof around the rooftop antenna location. Metal objects placed withi...

  • Page 293

    Scan button pushing the scan button causes the tuner to search for the next channel, pausing for eight seconds before con- tinuing to the next. To stop the search, push the scan button a second time. Info button pushing the info button will cycle the display informa- tion between artist, song title,...

  • Page 294

    Setup button pushing the setup button allows you to select the following items: • display sirius id number — push the audio/ select button to display the sirius id number. This number is used to activate, deactivate, or change the sirius subscription. Set button — to set the pushbutton memory when y...

  • Page 295

    Ipod®/usb/mp3 control — if equipped this feature allows an ipod® or external usb device to be plugged into the usb port, located in the center console or glove compartment. Ipod® control supports mini, 4g, photo, nano, 5g ipod® and iphone® devices. Some ipod® software versions may not fully support ...

  • Page 296

    Once the audio device is connected and synchronized to the vehicle’s ipod®/usb/mp3 control system (ipod® or external usb device may take a few minutes to connect), the audio device starts charging and is ready for use by pushing radio switches, as described below. Note: if the audio device battery i...

  • Page 297

    Mode. In play mode, the following buttons on the radio faceplate may be used to control the ipod® or external usb device and display data: • use the tune control knob to select the next or previous track. • turning it clockwise (forward) by one click, while playing a track, skips to the next track o...

  • Page 298

    • push the scan button to use ipod®/usb/mp3 de- vice scan mode, which will play the first ten seconds of each track in the current list and then forward to the next song. To stop scan mode and start playing the desired track, when it is playing the track, push the scan button again. During scan mode...

  • Page 299

    During all list modes, the ipod® displays all lists in “wrap-around” mode. So if the track is at the bottom of the list, just turn the wheel backward (counterclockwise) to get to the track faster. In list mode, the radio preset buttons are used as shortcuts to the following lists on the ipod® or ext...

  • Page 300

    Caution! • leaving the ipod® or external usb device (or any supported device) anywhere in the vehicle in ex- treme heat or cold can alter the operation or dam- age the device. Follow the device manufacturer’s guidelines. • placing items on the ipod® or external usb device, or connections to the ipod...

  • Page 301

    Selecting a different audio device 1. Push the phone button to begin. 2. After the # ready # prompt and following the beep, say # setup # , then say # select audio devices. # 3. Say the name of the audio device or ask the uconnect® phone system to list the audio devices. Next track use the seek up b...

  • Page 302

    The right-hand control is a rocker-type switch with a push-button in the center and controls the volume and mode of the sound system. Pushing the top of the rocker switch will increase the volume, and pushing the bottom of the rocker switch will decrease the volume. Pushing the center button will ma...

  • Page 303

    Cd player pushing the top of the switch once will go to the next track on the cd. Pushing the bottom of the switch once will go to the beginning of the current track, or to the beginning of the previous track if it is within eight seconds after the current track begins to play. If you push the switc...

  • Page 304

    5. Store the disc in its case after playing. 6. Do not expose the disc to direct sunlight. 7. Do not store the disc where temperatures may become too high. Note: if you experience difficulty in playing a particular disc, it may be damaged (e.G., scratched, reflective coat- ing removed, a hair, moist...

  • Page 305

    Manual heating and air conditioning the manual temperature controls consist of a series of outer rotary dials and inner push knobs. Blower control rotate this control to regulate the amount of air forced through the ven- tilation system in any mode. The blower speed increases as you move the control...

  • Page 306

    Note: if your air conditioning performance seems lower than expected, check the front of the a/c condenser located in front of the radiator for an accumulation of dirt or insects. Clean with a gentle water spray from behind the radiator and through the condenser. Fabric front fascia protectors may r...

  • Page 307

    Mode control (air direction) rotate this control to choose from sev- eral patterns of air distribution. You can select either a primary mode as identified by the symbols on the con- trol, or a blend of two of these modes. The closer the setting is to a particular symbol, the more air distribution yo...

  • Page 308

    • defrost air is directed through the windshield and side window demist outlets. Use this mode with maxi- mum blower and temperature settings for best wind- shield and side window defrosting. Note: • the air conditioning compressor operates in mix, defrost, or a blend of these modes, even if the air...

  • Page 309

    • the a/c will engage automatically to prevent fogging when the recirculation button is pushed and the mode control is set to panel or panel / floor. • the a/c can be deselected manually without disturb- ing the mode control selection. • when the ignition switch is turned to the lock position, the r...

  • Page 310

    Note: the auto position performs best for front seat occupants only. 2. Dial in the temperature you would like the system to maintain by ro- tating the temperature control knob (center knob). Once the com- fort level is selected, the system will maintain that level automatically using the heating sy...

  • Page 311

    Insects. Clean with a gentle water spray from behind the radiator and through the condenser. Fabric front fascia protectors may reduce airflow to the condenser, reducing air conditioning performance. Blower control for full automatic operation or for automatic blower operation, turn the blower knob ...

  • Page 312

    310 understanding your instrument panel.

  • Page 313

    The operator can override the auto mode setting to change airflow distribution by rotating the mode control knob (on the right) to one of the following positions. • panel air is directed through the outlets in the instru- ment panel. These outlets can be adjusted to direct airflow. Note: the center ...

  • Page 314

    • air conditioner control push this button to turn on the air conditioning during manual operation only. When the air conditioning is turned on, cool dehumidified air will flow through the outlets selected with the mode control dial. Push this but- ton a second time to turn off the air conditioning....

  • Page 315

    • most of the time, when in automatic operation, you can temporarily put the system into recirculation mode by pushing the recirculation button. However, under certain conditions, while in automatic mode, the system is blowing air out the defrost vents. When these conditions are present, and the rec...

  • Page 316

    Window fogging interior fogging on the windshield can be quickly re- moved by turning the mode selector to defrost. The defrost/floor mode can be used to maintain a clear windshield and provide sufficient heating. If side win- dow fogging becomes a problem, increase blower speed. Vehicle windows ten...

  • Page 317

    Control setting suggestions for various weather conditions 4 understanding your instrument panel 315.

  • Page 319: Starting And Operating

    Starting and operating contents ! Starting procedures . . . . . . . . . . . . . . . .321 ▫ manual transmission — if equipped . . . . . . .321 ▫ automatic transmission — if equipped . . . . .322 ▫ normal starting. . . . . . . . . . . . . . . . . . . . . . .322 ▫ extreme cold weather (below –20°f or −...

  • Page 320

    ! Autostick . . . . . . . . . . . . . . . . . . . . . . . . . .342 ▫ autostick (six-speed automatic transmission) . .342 ▫ autostick (cvt) . . . . . . . . . . . . . . . . . . . . . .344 ! Four-wheel drive operation — if equipped . . . . . . . . . . . . . . . . . . . . . . . . . . .346 ! On-road driv...

  • Page 321

    ! Tire safety information . . . . . . . . . . . . .374 ▫ tire markings . . . . . . . . . . . . . . . . . . . . . . . .374 ▫ tire identification number (tin). . . . . . . . . . .378 ▫ tire terminology and definitions . . . . . . . . . .380 ▫ tire loading and tire pressure . . . . . . . . . . .381 ! T...

  • Page 322

    ▫ reformulated gasoline . . . . . . . . . . . . . . . . .410 ▫ gasoline/oxygenate blends . . . . . . . . . . . . . .410 ▫ e-85 usage in non-flex fuel vehicles . . . . . . .411 ▫ mmt in gasoline. . . . . . . . . . . . . . . . . . . . . .411 ▫ materials added to fuel . . . . . . . . . . . . . . . .411...

  • Page 323

    Starting procedures before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. Warning! • before exiting a vehicle, always apply the parking brake, shift the transmission into park, and re- move the key fob from the ignition. When leaving the ...

  • Page 324

    Automatic transmission — if equipped the shift lever must be in the park or neutral position before you can start the engine. Depress the brake pedal before shifting to any driving gear. Note: you must press the brake pedal before shifting out of park. Tip start do not press the accelerator. Turn th...

  • Page 325

    Warning! (continued) another vehicle. This type of start can be dangerous if done improperly, so follow the procedure carefully. Refer to “jump starting” in “what to do in emer- gencies” for further information. Extreme cold weather (below –20°f or − 29°c) to ensure reliable starting at these temper...

  • Page 326

    Engine block heater — if equipped the engine block heater warms the engine, and permits quicker starts in cold weather. Connect the cord to a standard 110-115 volt ac electrical outlet with a grounded, three-wire extension cord. The engine block heater must be plugged in at least one hour to have an...

  • Page 327

    Use each gear in numerical order, do not skip a gear. Be sure the transmission is in first gear, (not third), when starting from a standing position. Damage to the clutch can result from starting in a gear higher than first gear. Caution! • launching in any gear except 1st gear will result in excess...

  • Page 328

    Never shift into reverse until the vehicle has come to a complete stop. Note: during cold weather, until the transmission lu- bricant is warm, you may experience slightly higher shift efforts. This is normal and not harmful to the transmis- sion. Recommended shift speeds to use your manual transmiss...

  • Page 329

    Downshifting proper downshifting will improve fuel economy and prolong engine life. Caution! If you skip a gear while downshifting or downshift at too high of a vehicle speed, these conditions may cause the engine to overspeed if too low of a gear is selected and the clutch pedal is released. Damage...

  • Page 330

    Note: you must press and hold the brake pedal while shifting out of park. Warning! • it is dangerous to shift out of park or neutral if the engine speed is higher than idle speed. If your foot is not firmly pressing the brake pedal, the vehicle could accelerate quickly forward or in re- verse. You c...

  • Page 331

    Warning! (continued) • never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking bra...

  • Page 332

    Six-speed automatic transmission — if equipped the transmission gear position display (located in the instrument cluster) indicates the transmission gear range. You must press the brake pedal to move the shift lever out of park (refer to “brake/transmission shift inter- lock system” in this section)...

  • Page 333

    Never attempt to use park while the vehicle is in motion. Apply the parking brake when leaving the vehicle in this range. When parking on a level surface, you may shift the transmission into park first, and then apply the parking brake. When parking on a hill, apply the parking brake before shifting...

  • Page 334

    Warning! (continued) • unintended movement of a vehicle could injure those in or near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, always apply the parking brake, shift the transmission into park, turn the engine off, and r...

  • Page 335

    Caution! • before moving the shift lever out of park, you must turn the ignition switch from the lock/off position to the on/run position, and also press the brake pedal. Otherwise, damage to the shift lever could result. • do not race the engine when shifting from park or neutral into another gear ...

  • Page 336

    Warning! Do not coast in neutral and never turn off the ignition to coast down a hill. These are unsafe practices that limit your response to changing traffic or road conditions. You might lose control of the vehicle and have a collision. Caution! Towing the vehicle, coasting, or driving for any oth...

  • Page 337

    If the transmission temperature exceeds normal operat- ing limits, the transmission controller will modify the transmission shift schedule and expand the range of torque converter clutch engagement. This is done to prevent transmission damage due to overheating. If the transmission becomes extremely...

  • Page 338

    6. Shift into the desired gear range. If the problem is no longer detected, the transmission will return to normal operation. Note: even if the transmission can be reset, we recom- mend that you visit your authorized dealer at your earliest possible convenience. Your authorized dealer has diagnostic...

  • Page 339

    Note: engagement of the torque converter clutch is inhibited at very cold temperatures. Because the engine speed is higher when the torque converter clutch is not engaged, it may seem as if the transmission is not shifting into overdrive when cold. This is normal. The torque converter clutch will fu...

  • Page 340

    Gear ranges do not race the engine when shifting from park or neutral into another gear range. Note: after selecting any gear range, wait a moment to allow the selected gear to engage before accelerating. This is especially important when the engine is cold. Park (p) this range supplements the parki...

  • Page 341

    Warning! (continued) • it is dangerous to shift out of park or neutral if the engine speed is higher than idle speed. If your foot is not firmly pressing the brake pedal, the vehicle could accelerate quickly forward or in re- verse. You could lose control of the vehicle and hit someone or something....

  • Page 342

    Caution! • before moving the shift lever out of park, you must turn the ignition switch from the lock/off position to the on/run position, and also press the brake pedal. Otherwise, damage to the shift lever could result. • do not race the engine when shifting from park or neutral into another gear ...

  • Page 343

    Warning! Do not coast in neutral and never turn off the ignition to coast down a hill. These are unsafe practices that limit your response to changing traffic or road conditions. You might lose control of the vehicle and have a collision. Caution! Towing the vehicle, coasting, or driving for any oth...

  • Page 344

    This happens, the transmission overheat indicator light will come on, and the vehicle will slow slightly until the transmission cools down enough to allow a return to the requested speed. This is done to prevent transmission damage due to overheating. If the high speed is main- tained, the overheati...

  • Page 345

    Condition would result. It will remain in the selected gear until another upshift or downshift is chosen, except as described below: • the transmission will automatically upshift when nec- essary to prevent engine over-speed. • the transmission will automatically downshift as the vehicle slows (to p...

  • Page 346

    Warning! Do not downshift for additional engine braking on a slippery surface. The drive wheels could lose their grip and the vehicle could skid, causing a collision or personal injury. Autostick (cvt) autostick is a driver-interactive transmission feature providing six manually selectable gear rati...

  • Page 347

    In autostick mode, the transmission will shift up or down when (+/-) is manually selected by the driver, unless an engine lugging or overspeed condition would result. It will remain in the selected gear until another upshift or downshift is chosen, except as described below: • the transmission will ...

  • Page 348

    Four-wheel drive operation — if equipped this feature provides full time, on-demand, four–wheel drive (4wd). Where one or more wheels have wheel spin or if addi- tional traction is needed in sand, deep snow, or loose traction surfaces, activate the “4wd lock” switch by pulling up once and releasing....

  • Page 349

    An advantage of the higher ground clearance is a better view of the road, allowing you to anticipate problems. They are not designed for cornering at the same speeds as conventional two-wheel drive vehicles any more than low-slung sports cars are designed to perform satisfacto- rily in off-road cond...

  • Page 350

    Warning! Always wear your seat belt and firmly tie down cargo. Unsecured cargo can become projectiles in an off-road situation. When to use low (l off-road) with the 4wd lock lever engaged when driving off-road, shift into low (l off-road) and activate the 4wd lock. This will provide additional trac...

  • Page 351

    A lower gear than necessary to maintain headway. Over- revving the engine can spin the wheels and traction will be lost. If you start to slow to a stop, try turning your steering wheel no more than a 1/4 turn quickly back and forth, while still applying throttle. This will allow the tires to get a f...

  • Page 352

    Use low (l off-road) with the 4wd lock engaged and esc turned off. Reduced tire pressure will drastically improve your traction and handling, while driving on the soft sand, but you must return the tires to normal air pressure before driving on pavement or other hard surfaces. Be sure you have a way...

  • Page 353

    Driving up hill once you have determined your ability to proceed and have shifted into the appropriate gear, line your vehicle up for the straightest possible run. Accelerate with an easy constant throttle and apply more power as you start up the hill. Do not race forward into a steep grade; the abr...

  • Page 354

    And proceed with caution. Allow engine and hill descent braking to control the descent and apply your brakes if necessary, but do not allow the tires to lock. Warning! Do not descend a steep grade in neutral. Use vehicle brakes in conjunction with engine braking. Descending a grade too fast could ca...

  • Page 355

    Warning! (continued) tipping and rolling the vehicle, which may result in severe injury. Always back carefully straight down a hill in reverse gear. Never back down a hill in neutral using only the vehicle brakes. Never drive diagonally across a hill, always drive straight up or down. Driving throug...

  • Page 356

    Before you cross any type of water as you approach any type of water, you need to deter- mine if you can cross it safely and responsibly. If neces- sary, get out and walk through the water or probe it with a stick. You need to be sure of its depth, approach angle, current and bottom condition. Be ca...

  • Page 357

    Always a good idea to check for damage. That way you can get any problems taken care of right away and have your vehicle ready when you need it. • completely inspect the underbody of your vehicle. Check tires, body structure, steering, suspension, and exhaust system for damage. • inspect the radiato...

  • Page 358

    Power steering the standard power steering system will give you good vehicle response and increased ease of maneuverability in tight spaces. The system will provide mechanical steering capability if power assist is lost. If for some reason the power assist is interrupted, it will still be possible t...

  • Page 359

    Caution! Do not use chemical flushes in your power steering system as the chemicals can damage your power steering components. Such damage is not covered by the new vehicle limited warranty. Warning! Fluid level should be checked on a level surface and with the engine off to prevent injury from movi...

  • Page 360

    When the parking brake is applied with the ignition switch in the on position, the “brake warning light” in the instrument cluster will illuminate. Note: • when the parking brake is applied and the automatic transmission is placed in gear, the “brake warning light” will flash. If vehicle speed is de...

  • Page 361

    Warning! • when leaving the vehicle, always remove the key fob from the ignition and lock your vehicle. • never leave children alone in a vehicle, or with access to an unlocked vehicle. • allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be...

  • Page 362

    Brake system your vehicle is equipped with power assisted brakes as standard equipment. In the event power assist is lost for any reason (for example, repeated brake applications with the engine off), the brakes will still function. How- ever, the effort required to brake the vehicle will be much gr...

  • Page 363

    Electronic brake control system your vehicle may be equipped with an optional ad- vanced electronic brake control system that includes anti-lock brake system (abs), traction control system (tcs), brake assist system (bas), electronic roll mitiga- tion (erm), hill descent control (hdc), hill start as...

  • Page 364

    Warning! (continued) • the capabilities of an abs-equipped vehicle must never be exploited in a reckless or dangerous manner which could jeopardize the user’s safety or the safety of others. The “abs warning light” monitors the abs system. The light will come on when the ignition switch is turned to...

  • Page 365

    Abs is activated during braking under certain road or stopping conditions. Abs-inducing conditions can in- clude ice, snow, gravel, bumps, railroad tracks, loose debris, or panic stops. You may also experience the following when the brake system goes into anti-lock mode: • the abs motor running (it ...

  • Page 366

    A limited slip differential and controls the wheel spin across a driven axle. If one wheel on a driven axle is spinning faster than the other, the system will apply the brake of the spinning wheel. This will allow more engine torque to be applied to the wheel that is not spinning. This feature remai...

  • Page 367

    Electronic roll mitigation (erm) this system anticipates the potential for wheel lift by monitoring the driver’s steering wheel input and the speed of the vehicle. When erm determines that the rate of change of the steering wheel angle and vehicles speed are sufficient to potentially cause wheel lif...

  • Page 368

    Hill descent control (hdc) — if equipped this system maintains vehicle speed while descending hills during off-road driving situations. Hdc will auto- matically apply the brakes to control downhill speed to between 4 mph (7 km/h) and 6 mph (9 km/h) depending on terrain. The system is activated by pl...

  • Page 369

    Warning! Hdc is only intended to assist the driver in control- ling vehicle speed when descending hills. The driver must remain attentive to the driving conditions and is responsible for maintaining a safe vehicle speed. Hill start assist (hsa) the hsa system is designed to assist the driver when st...

  • Page 370

    Warning! (continued) always remember the driver is responsible for brak- ing the vehicle. Disabling/enabling hsa if you wish to turn on or off the hsa system, it can be done using the customer programmable features in the electronic vehicle information center (evic). Refer to “electronic vehicle inf...

  • Page 371

    9. Turn the ignition switch to the off position and then back to the on position. If the sequence was com- pleted properly, the “esc activation/malfunction in- dicator light” will blink several times to confirm hsa is disabled. 10. Repeat these steps if you want to return this feature to it’s previo...

  • Page 372

    Warning! (continued) • esc cannot prevent accidents, including those re- sulting from excessive speed in turns, driving on very slippery surfaces, or hydroplaning. Esc also cannot prevent collisions resulting from loss of vehicle control due to inappropriate driver input for the conditions. Only a s...

  • Page 373

    To turn esc on again, momentarily press the “esc off” switch. This will restore the normal “esc on” mode of operation. Note: to improve the vehicle’s traction when driving with snow chains, or starting off in deep snow, sand or gravel, it may be desirable to switch to the “partial off” mode by press...

  • Page 374

    Appear in the odometer. Press and release the trip odometer button located on the instrument cluster to clear this message. In this mode, esc and tcs, except for the “limited slip” feature described in the tcs section, are turned off until the vehicle reaches a speed of 35 mph (56 km/h). At 35 mph (...

  • Page 375

    Esc activation/malfunction indicator light and esc off indicator light the “esc activation/malfunction indicator light” in the instrument cluster will come on when the ignition switch is cycled to the on/ run position. It should go out with the engine running. If the “esc activation/malfunction indi...

  • Page 376

    The “esc off indicator light” indicates the electronic stability control (esc) is partially off or full off. Tire safety information tire markings 1 — u.S. Dot safety standards code (tin) 4 — maximum load 2 — size designation 5 — maximum pressure 3 — service description 6 — treadwear, traction and t...

  • Page 377

    Note: • p (passenger) — metric tire sizing is based on u.S. Design standards. P-metric tires have the letter “p” molded into the sidewall preceding the size designa- tion. Example: p215/65r15 95h. • european — metric tire sizing is based on european design standards. Tires designed to this standard ...

  • Page 378

    Tire sizing chart example: example size designation: p215/65r15xl 95h, 215/65r15 96h, lt235/85r16c, t145/80d18 103m, 31x10.5 r15 lt p = passenger car tire size based on u.S. Design standards, or % ....Blank.... % = passenger car tire based on european design standards, or lt = light truck tire based...

  • Page 379

    Example: service description: 95 = load index – a numerical code associated with the maximum load a tire can carry h = speed symbol – a symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions – the maximum speed corres...

  • Page 380

    Example: maximum load – maximum load indicates the maximum load this tire is designed to carry maximum pressure – maximum pressure indicates the maximum permissible cold tire inflation pressure for this tire tire identification number (tin) the tin may be found on one or both sides of the tire, howe...

  • Page 381

    Example: dot ma l9 abcd 0301 dot = department of transportation – this symbol certifies that the tire is in compliance with the u.S. Department of transportation tire safety standards and is approved for highway use ma = code representing the tire manufacturing location (two digits) l9 = code repres...

  • Page 382

    Tire terminology and definitions term definition b-pillar the vehicle b-pillar is the structural member of the body located behind the front door. Cold tire inflation pressure cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least three hours,...

  • Page 383

    Tire loading and tire pressure tire and loading information placard location note: the proper cold tire inflation pressure is listed on the driver’s side b-pillar or the rear edge of the driver’s side door. Example tire placard location (door) example tire placard location (b-pillar) 5 starting and ...

  • Page 384

    Tire and loading information placard this placard tells you important information about the: 1. Number of people that can be carried in the vehicle. 2. Total weight your vehicle can carry. 3. Tire size designed for your vehicle. 4. Cold tire inflation pressures for the front, rear, and spare tires. ...

  • Page 385

    Note: under a maximum loaded vehicle condition, gross axle weight ratings (gawrs) for the front and rear axles must not be exceeded. For further information on gawrs, vehicle loading, and trailer towing, refer to “vehicle loading” in this section. To determine the maximum loading conditions of your ...

  • Page 386

    4. The resulting figure equals the available amount of cargo and luggage load capacity. For example, if “xxx” amount equals 1,400 lbs (635 kg) and there will be five 150 lb (68 kg) passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lbs (295 kg) (since 5 x 150 ...

  • Page 387

    5 starting and operating 385.

  • Page 388

    Warning! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. Tires — general information tire pressure proper tire inflation pressur...

  • Page 389

    Warning! (continued) • unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left. • always drive with each tire inflated to the recom- mended cold tire inflation pressure. Both under-inflation and over-inflation affect the stability of the v...

  • Page 390

    At least once a month: • check and adjust tire pressure with a good quality pocket-type pressure gauge. Do not make a visual judgement when determining proper inflation. Tires may look properly inflated even when they are under- inflated. • inspect tires for signs of tire wear or visible damage. Cau...

  • Page 391

    Tire pressure may increase from 2 to 6 psi (13 to 40 kpa) during operation. Do not reduce this normal pressure build up or your tire pressure will be too low. Tire pressures for high speed operation the manufacturer advocates driving at safe speeds and within posted speed limits. Where speed limits ...

  • Page 392

    Tire repair if your tire becomes damaged, it may be repaired if it meets the following criteria: • the tire has not been driven on when flat. • the damage is only on the tread section of your tire (sidewall damage is not repairable). • the puncture is no greater than a ¼ of an inch (6 mm). Consult a...

  • Page 393

    Summer tires do not contain the all season designation or mountain/snowflake symbol on the tire sidewall. Use summer tires only in sets of four; failure to do so may adversely affect the safety and handling of your vehicle. Warning! Do not use summer tires in snow/ice conditions. You could lose vehi...

  • Page 394

    While studded tires improve performance on ice, skid and traction capability on wet or dry surfaces may be poorer than that of non-studded tires. Some states pro- hibit studded tires; therefore, local laws should be checked before using these tire types. Run flat tires — if equipped run flat tires a...

  • Page 395

    Equipment tire and wheel found on the front or rear axle of your vehicle. This spare tire may be used in the tire rotation for your vehicle. If your vehicle has this option, refer to an authorized tire dealer for the recommended tire rotation pattern. Compact spare tire — if equipped the compact spa...

  • Page 396

    Full size spare — if equipped the full size spare is for temporary emergency use only. This tire may look like the originally equipped tire on the front or rear axle of your vehicle, but it is not. This spare tire may have limited tread life. When the tread is worn to the tread wear indicators, the ...

  • Page 397

    Tire spinning when stuck in mud, sand, snow, or ice conditions, do not spin your vehicle’s wheels above 30 mph (48 km/h) or for longer than 30 seconds continuously without stop- ping. Refer to “freeing a stuck vehicle” in “what to do in emergencies” for further information. Warning! Fast spinning ti...

  • Page 398

    These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth becomes a 1/16 of an inch (2 mm). When the tread is worn to the tread wear indicators, the tire should be replaced. Refer to “replacement tires” in this section for further information. L...

  • Page 399

    Replacement tires the tires on your new vehicle provide a balance of many characteristics. They should be inspected regularly for wear and correct cold tire inflation pressures. The manu- facturer strongly recommends that you use tires equiva- lent to the originals in size, quality and performance w...

  • Page 400

    Warning! • do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change sus- pension dimensions and performance characteris- tics, resulting in changes to steering, handling, and braking of your vehicle. This can caus...

  • Page 401

    Tire rotation recommendations the tires on the front and rear of your vehicle operate at different loads and perform different steering, driving, and braking functions. For these reasons, they wear at unequal rates. These effects can be reduced by timely rotation of tires. The benefits of rotation a...

  • Page 402

    Tire pressure monitoring system (tpms) the tire pressure monitor system (tpms) will warn the driver of a low tire pressure based on the vehicle recom- mended cold placard pressure. The tire pressure will vary with temperature by about 1 psi (7.0 kpa) for every 12°f (6.5°c). This means that when the ...

  • Page 403

    Driven for up to 20 minutes above 15 mph (24 km/h) in order for the tpms to receive this information. For example, your vehicle may have a recommended cold (parked for more than three hours) placard pressure of 30 psi (207 kpa). If the ambient temperature is 68°f (20°c) and the measured tire pressur...

  • Page 404

    Caution! (continued) • after inspecting or adjusting the tire pressure, always reinstall the valve stem cap. This will prevent moisture and dirt from entering the valve stem, which could damage the tire pressure moni- toring sensor. Note: • the tpms is not intended to replace normal tire care and ma...

  • Page 405

    The tpms uses wireless technology with wheel rim mounted electronic sensors to monitor tire pressure lev- els. Sensors, mounted to each wheel as part of the valve stem, transmit tire pressure readings to the receiver module. Note: it is particularly important for you to check the tire pressure in al...

  • Page 406

    Pressure monitoring telltale light will turn off when the fault condition no longer exists. A system fault can occur with any of the following scenarios: 1. Jamming due to electronic devices or driving next to facilities emitting the same radio frequencies as the tpm sensors. 2. Installing some form...

  • Page 407

    Long as no tire pressure is below the low-pressure warning limit in any of the four active road tires. The vehicle may need to be driven for up to 20 minutes above 15 mph (24 km/h) in order for the tpms to receive this information. Premium system — if equipped the tpms uses wireless technology with ...

  • Page 408

    Should a low tire condition occur on any of the four active road tire(s), you should stop as soon as possible and inflate all tires that are flashing on the graphic display to the vehicle’s recommended cold placard pres- sure value. The system will automatically update, the “low tire” text message w...

  • Page 409

    If the ignition key is cycled, this sequence will repeat, providing the system fault still exists. If the system fault no longer exists, the tire pressure monitoring telltale light will no longer flash, the # service tpm system # text message will not be present, and a pressure value will be display...

  • Page 410

    Pressure values still shown. This indicates that the pres- sure values are still being received from the tpm sensors but they may not be located in the correct vehicle position. The system still needs to be serviced as long as the # service tpm system # message is displayed. Note: your vehicle is eq...

  • Page 411

    Long as no tire pressure is below the low-pressure warning limit in any of the four active road tires. The vehicle may need to be driven for up to 20 minutes above 15 mph (24 km/h) in order for the tpms to receive this information. General information this device complies with part 15 of the fcc rul...

  • Page 412

    From operating with a heavy spark knock may void or not be covered by the new vehicle warranty. Reformulated gasoline many areas of the country require the use of cleaner burning gasoline referred to as “reformulated gasoline.” reformulated gasoline contain oxygenates and are spe- cifically blended ...

  • Page 413

    E-85 usage in non-flex fuel vehicles non-flex fuel vehicles (ffv) are compatible with gaso- line containing up to 10% ethanol (e10). Gasoline with higher ethanol content may void the new vehicle lim- ited warranty. If a non-ffv vehicle is inadvertently fueled with e-85 fuel, the engine will have som...

  • Page 414

    Fuel system cautions caution! Follow these guidelines to maintain your vehicle’s performance: • the use of leaded gasoline is prohibited by federal law. Using leaded gasoline can impair engine per- formance and damage the emissions control sys- tem. • an out-of-tune engine or certain fuel or ignitio...

  • Page 415

    Carbon monoxide warnings warning! Carbon monoxide (co) in exhaust gases is deadly. Follow the precautions below to prevent carbon monoxide poisoning: • do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas, which can kill. Never run the engine in a closed area, such...

  • Page 416

    After removing the gas cap, place the gas cap tether cable over a hook on the inside of the fuel door. This keeps the gas cap suspended away from and protects the vehicle’s surface. Caution! • damage to the fuel system or emission control system could result from using an improper fuel tank filler c...

  • Page 417

    Warning! (continued) • never add fuel when the engine is running. This is in violation of most state and federal fire regula- tions and may cause the mil to turn on. • a fire may result if gasoline is pumped into a portable container that is inside of a vehicle. You could be burned. Always place gas...

  • Page 418

    Vehicle loading as required by national highway traffic safety admin- istration regulations, your vehicle has a certification label affixed to the driver’s side door or b-pillar. Vehicle certification label your vehicle has a vehicle certification label attached to the driver’s door b-pillar. The la...

  • Page 419

    Inflation pressure this is the cold tire inflation pressure for your vehicle for all loading conditions up to full gawr. Curb weight the curb weight of a vehicle is defined as the total weight of the vehicle with all fluids, including vehicle fuel, at full capacity conditions, and with no occupants ...

  • Page 420

    Caution! Do not load your vehicle any heavier than the gvwr. If you do, parts on your vehicle can break, or it can change the way your vehicle handles. This could cause you to lose control. Also, overloading can shorten the life of your vehicle. Trailer towing in this section you will find safety ti...

  • Page 421

    The recommended way to measure gtw is to put your fully loaded trailer on a vehicle scale. The entire weight of the trailer must be supported by the scale. Gross combination weight rating (gcwr) the gcwr is the total permissible weight of your vehicle and trailer when weighed in combination. Gross a...

  • Page 422

    Frontal area the frontal area is the maximum height multiplied by the maximum width of the front of a trailer. Trailer sway control the trailer sway control is a telescoping link that can be installed between the hitch receiver and the trailer tongue that typically provides adjustable friction assoc...

  • Page 423

    Weight-distributing hitch a weight-distributing system works by applying lever- age through spring (load) bars. They are typically used for heavier loads to distribute trailer tongue weight to the tow vehicle’s front axle and the trailer axle(s). When used in accordance with the manufacturer’s direc...

  • Page 424

    Trailer hitch classification the following chart provides the industry standard for the maximum trailer weight a given trailer hitch class can tow and should be used to assist you in selecting the correct trailer hitch for your intended towing condition. Trailer hitch classification definitions clas...

  • Page 425

    Trailer towing weights (maximum trailer weight ratings) the following chart provides the maximum trailer weight ratings towable for your given drivetrain. Engine/transmission frontal area maximum gtw (gross trailer wt.) maximum tongue wt. (see note) 2.0l auto/man 22 sq ft (2.04 sq m) 1,000 lbs (450 ...

  • Page 426

    Note: the trailer tongue weight must be considered as part of the combined weight of occupants and cargo, and should never exceed the weight referenced on the tire and loading information placard. Refer to “tire safety information” in “starting and operating” for further information. Trailer and ton...

  • Page 427

    Consider the following items when computing the weight on the rear axle of the vehicle: • the tongue weight of the trailer. • the weight of any other type of cargo or equipment put in or on your vehicle. • the weight of the driver and all passengers. Note: remember that everything put into or on the...

  • Page 428

    Warning! Improper towing can lead to a collision. Follow these guidelines to make your trailer towing as safe as possible: • make certain that the load is secured in the trailer and will not shift during travel. When trailering cargo that is not fully secured, dynamic load shifts can occur that may ...

  • Page 429

    Warning! (continued) • total weight must be distributed between the tow vehicle and the trailer such that the following four ratings are not exceeded: 1. Gvwr 2. Gtw 3. Gawr 4. Tongue weight rating for the trailer hitch uti- lized. Towing requirements — tires • do not attempt to tow a trailer while ...

  • Page 430

    Towing requirements — trailer brakes • do not interconnect the hydraulic brake system or vacuum system of your vehicle with that of the trailer. This could cause inadequate braking and possible personal injury. • an electronically actuated trailer brake controller is required when towing a trailer w...

  • Page 431

    Caution! (continued) could lead to accelerated brake lining wear, higher brake pedal effort, and longer stopping distances. Towing requirements — trailer lights and wiring whenever you pull a trailer, regardless of the trailer size, stoplights and turn signals on the trailer are required for motorin...

  • Page 432

    Towing tips before setting out on a trip, practice turning, stopping, and backing up the trailer in an area located away from heavy traffic. Manual transmission — if equipped if using a manual transmission vehicle for trailer towing, all starts must be in first gear to avoid excessive clutch slippag...

  • Page 433

    Note: using a lower gear ratio while operating the vehicle under heavy loading conditions, will improve performance and extend transmission life by reducing excessive shifting and heat buildup. This action will also provide better engine braking. If you regularly tow a trailer for more than 45 minut...

  • Page 434

    Electronic speed control — if equipped • do not use in hilly terrain or with heavy loads. • when using the speed control, if you experience speed drops greater than 10 mph (16 km/h), disengage until you can get back to cruising speed. • use speed control in flat terrain and with light loads to maxim...

  • Page 435

    Recreational towing (behind motorhome, etc.) towing this vehicle behind another vehicle towing condition wheels off the ground manual transmission automatic transmission flat tow none • transmission in neu- tral • key in acc position not allowed dolly tow front ok (fwd only) ok (fwd only) rear not a...

  • Page 436

    Caution! • do not flat tow any vehicle equipped with an automatic transmission. Damage to the drivetrain will result. If these vehicles require towing, make sure all drive wheels are off the ground. • do not dolly tow any 4wd vehicle. Internal damage to the transmission or transfer case will occur i...

  • Page 437: Contents

    What to do in emergencies contents ! Hazard warning flashers . . . . . . . . . . .437 ! If your engine overheats . . . . . . . . . . . .437 ! Wheel and tire torque specifications . . . . . . . . . . . . . . . . . . . . . .438 ▫ torque specifications . . . . . . . . . . . . . . . . . .438 ! Jacking a...

  • Page 438

    ! Shift lever override . . . . . . . . . . . . . . . .468 ! Towing a disabled vehicle . . . . . . . . . . .470 ▫ with ignition key . . . . . . . . . . . . . . . . . . . . .472 436 what to do in emergencies.

  • Page 439

    Hazard warning flashers the hazard warning flasher switch is located on the instrument panel, below the radio. Push the switch to turn on the hazard warning flasher. When the switch is activated, all direc- tional turn signals will flash on and off to warn oncoming traffic of an emergency. Push the ...

  • Page 440

    Caution! Driving with a hot cooling system could damage your vehicle. If the pointer rises to the h (red) mark, the instrument cluster will sound a chime. When safe, pull over and stop the vehicle with the engine at idle. Turn off the air conditioning and wait until the pointer drops back into the n...

  • Page 441

    **use only your authorized dealer recommended lug nuts/bolts and clean or remove any dirt or oil before tightening. Inspect the wheel mounting surface prior to mounting the tire and remove any corrosion or loose particles. Tighten the lug nuts/bolts in a star pattern until each nut/bolt has been tig...

  • Page 442

    Warning! To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts fully until the vehicle has been lowered. Failure to follow this warning may result in personal injury. Jacking and tire changing warning! • do not attempt to change a tire on the side of the vehicle close to...

  • Page 443

    Jack location the jack and jack-handle are stowed under the load floor in the cargo area. Spare tire stowage the compact spare tire is stowed under the rear load floor in the cargo area. Spare tire removal lift up the load floor cover and remove the hold down. Preparations for jacking 1. Park the ve...

  • Page 444

    2. Turn on the hazard warning flasher. 3. Set the parking brake. 4. Place the shift lever in park (automatic transmission) or reverse (manual transmission). 5. Turn off the ignition. 6. Block both the front and rear of the wheel diagonally opposite of the jacking position. For example, if changing t...

  • Page 445

    Warning! (continued) • do not let anyone sit in the vehicle when it is on a jack. • do not get under the vehicle when it is on a jack. If you need to get under a raised vehicle, take it to a service center where it can be raised on a lift. • only use the jack in the positions indicated and for lifti...

  • Page 446

    Note: refer to “tires — general information” in “start- ing and operating” for further information about the spare tire, it’s use, and operation. 1. Remove the scissors jack and lug wrench from the spare wheel as an assembly. Turn the jack screw to the left to loosen the lug wrench and remove the wr...

  • Page 447

    2. Loosen, but do not remove, the wheel nuts by turning them to the left one turn while the wheel is still on the ground. Note: there are front and rear jacking locations on each side of the body. The front locations are outlined by two triangular cutouts on one of the flanges in the sill flange ass...

  • Page 448

    Do not raise the vehicle until you are sure the jack is securely engaged. 3. Turn the jack screw to the left until the jack can be placed under the jacking location. Once the jack is positioned, turn the jack screw to the right until the jack head is properly engaged with the lift area closest to th...

  • Page 449

    Warning! To avoid the risk of forcing the vehicle off the jack, do not tighten the wheel nuts fully until the vehicle has been lowered. Failure to follow this warning may result in serious injury. Caution! Be sure to mount the spare tire with the valve stem facing outward. The vehicle could be damag...

  • Page 450

    Warning! To avoid possible personal injury, handle the wheel covers with care to avoid contact with any sharp edges. Note: the wheel cover is held on the wheel by the wheel nuts. When reinstalling the original wheel, prop- erly align the wheel cover to the valve stem, place the wheel cover onto the ...

  • Page 451

    Warning! A loose tire thrown forward in a collision or hard stop could injure the occupants in the vehicle. Have the deflated (flat) tire repaired or replaced immedi- ately. 10. Check the spare tire pressure as soon as possible. Correct the tire pressure as required. Road tire installation vehicles ...

  • Page 452

    3. Install the five wheel lug nuts with the cone shaped end of the nut toward the wheel. Lightly tighten the lug nuts. Warning! To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts fully until the vehicle has been lowered. Failure to follow this warning may result in se...

  • Page 453

    3. Lower the vehicle to the ground by turning the jack handle counterclockwise. 4. Finish tightening the lug nuts. Push down on the wrench while at the end of the handle for increased leverage. Refer to “torque specifications” in this sec- tion for correct lug nut torque. 5. After 25 miles (40 km) c...

  • Page 454

    Tire service kit components and operation using the mode select knob and hoses your tire service kit is equipped with the following symbols to indicate the air or sealant mode. Selecting air mode push in the mode select knob (5) and turn to this position for air pump operation only. Use the black ai...

  • Page 455

    Using the power button push and release the power button (4) once to turn on the tire service kit. Push and release the power button (4) again to turn off the tire service kit. Using the deflation button push the deflation button (2) to reduce the air pressure in the tire if it becomes over-inflated...

  • Page 456

    From the vehicle or tire and wheel components. Once the sealant dries, it can easily be peeled off and properly discarded. • for optimum performance, make sure the valve stem on the wheel is free of debris before connecting the tire service kit. • you can use the tire service kit air pump to inflate...

  • Page 457

    Warning! (continued) • keep tire service kit away from open flames or heat source. • a loose tire service kit thrown forward in a collision or hard stop could endanger the occupants of the vehicle. Always stow the tire service kit in the place provided. Failure to follow these warn- ings can result ...

  • Page 458

    On the ground. This will provide the best positioning of the kit when injecting the sealant into the deflated tire and running the air pump. Move the vehicle as necessary to place the valve stem in this position before proceeding. 3. Place the transmission in park (auto transmission) or in gear (man...

  • Page 459

    Note: sealant may leak out through the puncture in the tire. If the sealant (white fluid) does not flow within 0 – 10 seconds through the sealant hose (6): 1. Push the power button (4) to turn off the tire service kit. Disconnect the sealant hose (6) from the valve stem. Make sure the valve stem is ...

  • Page 460

    Latch pillar (recommended pressure). Check the tire pressure by looking at the pressure gauge (3). If the tire does not inflate to at least 26 psi (1.8 bar) pressure within 15 minutes: • the tire is too badly damaged. Do not attempt to drive the vehicle further. Call for assistance. Note: if the tir...

  • Page 461

    (d) drive vehicle: immediately after injecting sealant and inflating the tire, drive the vehicle 5 miles (8 km) or 10 minutes to ensure distribution of the tire service kit sealant within the tire. Do not exceed 55 mph (90 km/h). Warning! Tire service kit is not a permanent flat tire repair. Have th...

  • Page 462

    If tire pressure is less than 19 psi (1.3 bar): the tire is too badly damaged. Do not attempt to drive the vehicle further. Call for assistance. If the tire pressure is 19 psi (1.3 bar) or higher: 1. Push the power button (4) to turn on tire service kit and inflate the tire to the pressure indicated...

  • Page 463

    3. Push the sealant bottle release button. The sealant bottle (1) will pop up. Remove the bottle and dispose of it accordingly. 4. Clean any remaining sealant from the tire service kit housing. 5. Position the new sealant bottle (1) in the housing so that the sealant hose (6) aligns with the hose sl...

  • Page 464

    Warning! Do not attempt jump-starting if the battery is frozen. It could rupture or explode and cause personal injury. Preparations for jump-start the battery in your vehicle is located in the front of the engine compartment below the air intake duct. To access the battery remove the air intake duct...

  • Page 465

    Warning! • take care to avoid the radiator cooling fan when- ever the hood is raised. It can start anytime the ignition switch is on. You can be injured by moving fan blades. • remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact. You co...

  • Page 466

    1. Set the parking brake, shift the automatic transmission into park (manual transmission to neutral) and turn the ignition to lock. 2. Turn off the heater, radio, and all unnecessary electri- cal accessories. 3. If using another vehicle to jump-start the battery, park the vehicle within the jumper ...

  • Page 467

    Connecting the jumper cables 1. Connect the positive (+) end of the jumper cable to the positive (+) post of the discharged vehicle. 2. Connect the opposite end of the positive (+) jumper cable to the positive (+) post of the booster battery. 3. Connect the negative end (-) of the jumper cable to th...

  • Page 468

    6. Once the engine is started, remove the jumper cables in the reverse sequence: disconnecting the jumper cables 1. Disconnect the negative (-) end of the jumper cable from the engine ground of the vehicle with the dis- charged battery. 2. Disconnect the opposite end of the negative (-) jumper cable...

  • Page 469

    And reverse (with automatic transmission) or 2nd gear and reverse (with manual transmission), while gently pushing the accelerator. Use the least amount of accelera- tor pedal pressure that will maintain the rocking motion, without spinning the wheels, or racing the engine. Caution! Racing the engin...

  • Page 470

    Warning! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause damage, or even failure, of the axle and tires. A tire could explode and injure someone. Do not spin your vehi- cle’s wheels faster than 30 mph (48 km/h) or for longer than 30 seconds continuously w...

  • Page 471

    4. Turn the ignition switch to the acc or on/run position, but do not start the engine. 5. Push and maintain firm pressure on the brake pedal. 6. Insert the screwdriver or similar tool into the access port, and push and hold the override release lever forward. 7. Move the shift lever to the neutral ...

  • Page 472

    Towing a disabled vehicle this section describes procedures for towing a disabled vehicle using a commercial towing service. 470 what to do in emergencies.

  • Page 473

    Towing condition wheels off the ground manual transmission 6-speed auto- matic (fwd only) 6-speed automatic 4wd cvt automatic transmission flat tow none • transmis- sion in neu- tral • key in acc or on/run position if transmission is operable: • transmission in neutral • 25 mph (40 km/h) max speed •...

  • Page 474

    With ignition key automatic transmission • front wheel drive (fwd) vehicles can be towed with the front wheels elevated, or on a flatbed truck (all four wheels off the ground). • four-wheel drive (4wd) vehicles can be towed on a flatbed truck (all four wheels off the ground). If the transmission is ...

  • Page 475

    Manual transmission • front wheel drive (fwd) or four-wheel drive (4wd) vehicles can be flat towed (all four wheels on the ground) with the transmission in neutral. • fwd vehicles can be towed with the front wheels elevated. • fwd or 4wd vehicles can be towed on a flatbed truck (all wheels off the g...

  • Page 476

    All transmissions if you must use the accessories (wipers, defroster, etc.) while being towed, the key must be in the on/run position, not the acc position. Make certain the trans- mission remains in neutral. Caution! • do not use sling-type equipment when towing. Vehicle damage may occur. • when se...

  • Page 477: Maintaining Your Vehicle

    Maintaining your vehicle contents ! Engine compartment — 2.0l . . . . . . . . . .477 ! Engine compartment — 2.4l . . . . . . . . . .478 ! Onboard diagnostic system — obd ii . .479 ▫ loose fuel filler cap message . . . . . . . . . . . .479 ! Emissions inspection and maintenance programs . . . . . . ....

  • Page 478

    ▫ automatic transmission (six-speed) — if equipped . . . . . . . . . . . . . . . . . . . . . . . . . . .504 ▫ automatic transmission (cvt) — if equipped . . . . . . . . . . . . . . . . . . . . . . . . . . .506 ▫ manual transmission — if equipped . . . . . . .508 ▫ rear drive assembly (rda) — awd/4wd...

  • Page 479

    Engine compartment — 2.0l 1 — washer fluid reservoir 6 — air cleaner filter 2 — power steering fluid reservoir 7 — coolant pressure cap 3 — engine oil fill 8 — engine oil dipstick 4 — brake fluid reservoir 9 — engine coolant reservoir 5 — integrated power module (fuses) 7 maintaining your vehicle 47...

  • Page 480

    Engine compartment — 2.4l 1 — washer fluid reservoir 6 — air cleaner filter 2 — power steering fluid reservoir 7 — coolant pressure cap 3 — engine oil fill 8 — engine oil dipstick 4 — brake fluid reservoir 9 — engine coolant reservoir 5 — integrated power module (fuses) 478 maintaining your vehicle.

  • Page 481

    Onboard diagnostic system — obd ii your vehicle is equipped with a sophisticated onboard diagnostic system called obd ii. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide ex...

  • Page 482

    Persists, the message will appear the next time the vehicle is started. This might indicate a damaged cap. If the problem is detected twice in a row, the system will turn on the mil. Resolving the problem will turn the mil light off. Emissions inspection and maintenance programs in some localities, ...

  • Page 483

    3. Approximately 15 seconds later, one of two things will happen: • the mil will flash for about 10 seconds and then return to being fully illuminated until you turn off the ignition or start the engine. This means that your vehicle’s obd ii system is not ready and you should not proceed to the i/m ...

  • Page 484

    Dealer service your authorized dealer has the qualified service person- nel, special tools, and equipment to perform all service operations in an expert manner. Service manuals are available which include detailed service information for your vehicle. Refer to these service manuals before attempting...

  • Page 485

    Caution! • failure to properly maintain your vehicle or per- form repairs and service when necessary could result in more costly repairs, damage to other components or negatively impact vehicle perfor- mance. Immediately have potential malfunctions examined by an authorized dealer or qualified repai...

  • Page 486

    Low end of the indicated range will result in the oil level at the full end of the indicator range. Caution! Do not overfill the engine. Overfilling the engine will cause oil aeration, which can lead to loss of oil pressure and an increase in oil temperature. This could damage your engine. Also, be ...

  • Page 487

    Caution! Do not use chemical flushes in your engine oil as the chemicals can damage your engine. Such damage is not covered by the new vehicle limited warranty. Engine oil viscosity (sae grade) mopar® sae 5w-20 engine oil or equivalent pennzoil® or shell helix® is recommended for all operating tem- ...

  • Page 488

    Station or governmental agency for advice on how and where used oil and oil filters can be safely discarded in your area. Engine oil filter the engine oil filter should be replaced with a new filter at every engine oil change. Engine oil filter selection this manufacturer’s engines have a full-flow ...

  • Page 489

    Maintenance-free battery your vehicle is equipped with a maintenance-free battery. You will never have to add water, nor is periodic main- tenance required. Warning! • battery fluid is a corrosive acid solution and can burn or even blind you. Do not allow battery fluid to contact your eyes, skin, or...

  • Page 490

    Caution! • it is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked positive (+) and negative (-) and are identified on the battery case. Cable clamps should be ...

  • Page 491

    Caution! Do not use chemical flushes in your air conditioning system as the chemicals can damage your air condi- tioning components. Such damage is not covered by the new vehicle limited warranty. Refrigerant recovery and recycling r-134a air conditioning refrigerant is a hydrofluoro- carbon (hfc) t...

  • Page 492

    4. Disengage the two retaining tabs that secure the filter cover to the hvac housing, and remove the cover. 5. Remove the a/c air filter by pulling it straight out of the housing. 6. Install the a/c air filter with the arrow on the filter pointing toward the floor. When installing the filter cover, ...

  • Page 493

    Should be wiped clean to remove dust and grit; after lubricating excess oil and grease should be removed. Particular attention should also be given to hood latching components to ensure proper function. When performing other underhood services, the hood latch, release mecha- nism and safety catch sh...

  • Page 494

    When refilling the washer fluid reservoir, take some washer fluid and apply it to a cloth or towel and wipe clean the wiper blades, this will help blade performance. To prevent freeze-up of your windshield washer system in cold weather, select a solution or mixture that meets or exceeds the temperat...

  • Page 495

    Warning! • exhaust gases can injure or kill. They contain carbon monoxide (co), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing co, refer to “safety tips/exhaust gas” in “things to know before starting your vehicle” for further...

  • Page 496

    Under normal operating conditions, the catalytic con- verter will not require maintenance. However, it is im- portant to keep the engine properly tuned to assure proper catalyst operation and prevent possible catalyst damage. Note: intentional tampering with emissions control systems can result in c...

  • Page 497

    Cooling system warning! • when working near the radiator cooling fan, disconnect the fan motor lead or turn the ignition switch to the off position. The fan is temperature controlled and can start at any time the ignition switch is in the on position. • you or others can be badly burned by hot engin...

  • Page 498

    Cooling system — drain, flush and refill note: some vehicles require special tools to add coolant properly. Failure to fill these systems properly could lead to severe internal engine damage. If any coolant is needed to be added to the system please contact your local authorized dealer. If the engin...

  • Page 499

    Caution! (continued) • do not use water alone or alcohol-based engine coolant (antifreeze) products. Do not use additional rust inhibitors or antirust products, as they may not be compatible with the radiator engine coolant and may plug the radiator. • this vehicle has not been designed for use with...

  • Page 500

    (antifreeze) solution. The use of lower quality water will reduce the amount of corrosion protection in the engine cooling system. Please note that it is the owner’s responsibility to main- tain the proper level of protection against freezing ac- cording to the temperatures occurring in the area whe...

  • Page 501

    Warning! • the warning words “do not open hot” on the cooling system pressure cap are a safety precaution. Never add engine coolant (antifreeze) when the engine is overheated. Do not loosen or remove the cap to cool an overheated engine. Heat causes pressure to build up in the cooling system. To pre...

  • Page 502

    Long as the engine operating temperature is satisfactory, the coolant bottle need only be checked once a month. When additional engine coolant (antifreeze) is needed to maintain the proper level, it should be added to the coolant bottle. Do not overfill. Points to remember note: when the vehicle is ...

  • Page 503

    • keep the front of the radiator clean. If your vehicle is equipped with air conditioning, keep the front of the condenser clean. • do not change the thermostat for summer or winter operation. If replacement is ever necessary, install only the correct type thermostat. Other designs may result in uns...

  • Page 504

    When the pads are replaced. However, low fluid level may be caused by a leak and a checkup may be needed. Note: if your vehicle is equipped with a manual trans- mission , the brake fluid reservoir supplies fluid to both the brake system and the clutch release system. The two systems are separated in...

  • Page 505

    Warning! (continued) • to avoid contamination from foreign matter or moisture, use only new brake fluid or fluid that has been in a tightly closed container. Keep the master cylinder reservoir cap secured at all times. Brake fluid in a open container absorbs moisture from the air resulting in a lowe...

  • Page 506

    Automatic transmission (six-speed) — if equipped selection of lubricant (six-speed transmission) it is important to use the proper transmission fluid to ensure optimum transmission performance and life. Use only the manufacturer’s specified transmission fluid. Refer to “fluids, lubricants, and genui...

  • Page 507

    Caution! Do not use chemical flushes in your transmission as the chemicals can damage your transmission compo- nents. Such damage is not covered by the new vehicle limited warranty. Fluid level check the fluid level is preset at the factory and does not require adjustment under normal operating cond...

  • Page 508

    Automatic transmission (cvt) — if equipped selection of lubricant (cvt) it is important to use the proper transmission fluid to ensure optimum transmission performance and life. Use only the manufacturer’s specified transmission fluid which has the special friction coefficient additives neces- sary ...

  • Page 509

    Caution! Do not use chemical flushes in your transmission as the chemicals can damage your transmission compo- nents. Such damage is not covered by the new vehicle limited warranty. Fluid level check the fluid level is preset at the factory and does not require adjustment under normal operating cond...

  • Page 510

    Manual transmission — if equipped lubricant selection use only the manufacturers recommended transmission fluid. Refer to “fluids, lubricants, and genuine parts” in “maintaining your vehicle” for further information. Fluid level check check the fluid level by removing the fill plug. The fluid level ...

  • Page 511

    Frequency of fluid change refer to the “maintenance schedule” for the proper maintenance intervals. Power transfer unit (ptu) — awd/4wd models only lubricant selection use only the manufacturer’s recommended fluid. Refer to “fluids, lubricants, and genuine parts” in “maintain- ing your vehicle” for ...

  • Page 512

    The following maintenance recommendations will enable you to obtain maximum benefit from the corrosion resistance built into your vehicle. What causes corrosion? Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle. The most common causes are: • road...

  • Page 513

    Caution! • do not use abrasive or strong cleaning materials such as steel wool or scouring powder that will scratch metal and painted surfaces. • use of power washers exceeding 1,200 psi (8 274 kpa) can result in damage or removal of paint and decals. Special care • if you drive on salted or dusty r...

  • Page 514

    Wheel and wheel trim care • all wheels and wheel trim, especially aluminum and chrome plated wheels, should be cleaned regularly with a mild soap and water to prevent corrosion. • to remove heavy soil and/or excessive brake dust, use mopar® wheel cleaner. Note: if your vehicle is equipped with dark ...

  • Page 515

    • for tough stains, apply mopar® total clean, or a mild soap solution to a clean, damp cloth and remove stain. Use a fresh, damp towel to remove soap residue. • for grease stains, apply mopar® multi-purpose cleaner to a clean, damp cloth and remove stain. Use a fresh, damp towel to remove soap resid...

  • Page 516

    Caution! Do not use alcohol and alcohol-based and/or keton based cleaning products to clean leather seats, as damage to the seat may result. Cleaning headlights your vehicle has plastic headlights that are lighter and less susceptible to stone breakage than glass headlights. Plastic is not as scratc...

  • Page 517

    Instrument panel bezels caution! When installing hanging air fresheners in your ve- hicle, read the installation instructions carefully. Some air fresheners will damage the finish of painted or decorated parts if allowed to directly contact any surface. Cleaning plastic instrument cluster lenses the...

  • Page 518

    Warning! A frayed or torn belt could rip apart in a collision and leave you with no protection. Inspect the belt system periodically, checking for cuts, frays, or loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Seat belt assemblies must be replaced a...

  • Page 519

    Warning! (continued) • if a general protection fuse for safety systems (air bag system, braking system), power unit systems (engine system, gearbox system) or steering system blows, contact an authorized dealer. Integrated power module (ipm) the integrated power module is located in the engine compa...

  • Page 520

    Cavity cartridge fuse mini-fuse description 3 10 amp red rear center brake light switch 4 10 amp red ignition switch/occupant classification module 5 15 amp lt blue battery feed for power tech 6 10 amp red power mirror/steering con- trol satellite radio/hands- free phone 7 30 amp green ignition off ...

  • Page 521

    Cavity cartridge fuse mini-fuse description 13 20 amp yellow cigar lighter 14 10 amp red instrument cluster 15 40 amp green radiator fan 16 15 amp lt blue dome lamp/sunroof/rear wiper motor 17 10 amp red wireless control module 18 40 amp green auto shutdown relay 19 20 amp yellow radio amplifiers 20...

  • Page 522

    Cavity cartridge fuse mini-fuse description 26 15 amp lt blue auto shutdown relay 27 10 amp red airbag control module 28 10 amp red airbag control module/ occupant classification mod- ule 29 hot car (no fuse required) 30 20 amp yellow heated seat – if equipped 31 10 amp red headlamp washer – if equi...

  • Page 523

    Cavity cartridge fuse mini-fuse description 36 30 amp pink headlamp/washer control/ smart glass – if equipped 37 25 amp clear diesel heater and h2/mod power top caution! • when installing the ipm cover, it is important to ensure the cover is properly positioned and fully latched. Failure to do so ma...

  • Page 524

    Vehicle storage if you will not be using your vehicle for more than 21 days, you may want to take steps to preserve your battery. • disengage the mini-fuse in the power distribution center labeled iod (ignition off-draw). • or disconnect the negative cable from the battery. • anytime you store your ...

  • Page 525

    Interior bulbs bulb number front header lamp t578 center dome lamp t578 rear cargo lamp/flashlight 8–a35lf exterior bulbs bulb number low beam/high beam headlamp h13 front park/turn signal/side marker lamp 3757ka front fog lamp psx24w center high mounted stop lamp (chmsl) led assembly (serviced at a...

  • Page 526

    Bulb replacement note: lens fogging can occur under certain atmo- spheric conditions. This will usually clear as atmospheric conditions change to allow the condensation to change back into a vapor. Turning the lamps on will usually accelerate the clearing process. Headlamps 1. Raise the hood and loc...

  • Page 527

    Rear tail, turn signal and backup lamps 1. Raise the liftgate. 2. Remove the two push-pins from the taillamp housing. 3. Grasp the taillamp and pull firmly to disengage the light from the aperture panel. 4. Twist and remove socket from the light. 5. Remove bulb from socket and replace. License lamps...

  • Page 528

    Fluid capacities u.S. Metric fuel (approximate) 13.6 gallons 51 liters engine oil with filter 2.0l and 2.4l engine (sae 5w-20, api certified) 4.5 quarts 4.26 liters cooling system * 2.0l and 2.4l engine (mopar® antifreeze/engine coolant 10 year/150,000 mile formula or equivalent) 7.2 quarts 6.8 lite...

  • Page 529

    Fluids, lubricants and genuine parts engine component fluid, lubricant, or genuine part engine coolant we recommend you use mopar® antifreeze/coolant 10 year/150,000 mile formula oat (organic additive technology) or equivalent meeting the requirements of chrysler material standard ms.90032. Engine o...

  • Page 530

    Caution! • mixing of engine coolant (antifreeze) other than specified organic additive technology (oat) en- gine coolant (antifreeze), may result in engine damage and may decrease corrosion protection. Organic additive technology (oat) engine cool- ant is different and should not be mixed with hybri...

  • Page 531

    Chassis component fluid, lubricant, or genuine part automatic transmission (cvt) — if equipped use only mopar® cvtf+4® continuously variable transmission fluid or equivalent. Failure to use the correct fluid may affect the function or performance of your transmission. Automatic transmission (six-spe...

  • Page 533: Maintenance Schedules

    Maintenance schedules contents ! Maintenance schedule . . . . . . . . . . . . . .532 ▫ maintenance chart. . . . . . . . . . . . . . . . . . . . .534 8.

  • Page 534

    Maintenance schedule your vehicle is equipped with an automatic oil change indicator system. The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance. Based on engine operation conditions, the oil change indicator message will illuminate. This...

  • Page 535

    Once a month or before a long trip: • check engine oil level • check windshield washer fluid level • check the tire inflation pressures and look for unusual wear or damage • check the fluid levels of the coolant reservoir, brake master cylinder, power steering and fill as needed • check function of ...

  • Page 536

    Maintenance chart refer to the maintenance schedules on the following pages for the required maintenance intervals. Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 110,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 1...

  • Page 537

    Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 110,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 112,000 128,000 144,000 160,000 176,000 192,000 208,000...

  • Page 538

    Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 110,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 112,000 128,000 144,000 160,000 176,000 192,000 208,000...

  • Page 539

    Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 110,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 112,000 128,000 144,000 160,000 176,000 192,000 208,000...

  • Page 540

    Warning! • you can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent me- chanic. • failure to properly inspect and m...

  • Page 541: Contents

    If you need consumer assistance contents ! Suggestions for obtaining service for your vehicle . . . . . . . . . . . . . . . . . . . . . . .541 ▫ prepare for the appointment. . . . . . . . . . . . .541 ▫ prepare a list . . . . . . . . . . . . . . . . . . . . . . . .541 ▫ be reasonable with requests ....

  • Page 542

    ! Department of transportation uniform tire quality grades . . . . . . . . . . . . . . . . .547 ▫ treadwear. . . . . . . . . . . . . . . . . . . . . . . . . . .547 ▫ traction grades . . . . . . . . . . . . . . . . . . . . . . .547 ▫ temperature grades. . . . . . . . . . . . . . . . . . . .548 540 if...

  • Page 543

    Suggestions for obtaining service for your vehicle prepare for the appointment if you are having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty. Discuss additional charges with the service manager....

  • Page 544

    Facilities, factory-trained technicians, special tools, and the latest information to ensure the vehicle is fixed correctly and in a timely manner. This is why you should always talk to an authorized dealer service manager first. Most matters can be re- solved with this process. • if for some reason...

  • Page 545

    In mexico contact av. Prolongacion paseo de la reforma, 1240 sante fe c.P. 05109 mexico, d. F. In mexico city: 5081-7568 outside mexico city: 1-800-505-1300 customer assistance for the hearing or speech impaired (tdd/tty) to assist customers who have hearing difficulties, the manufacturer has instal...

  • Page 546

    The manufacturer will not stand behind any service contract that is not the manufacturer’s service contract. It is not responsible for any service contract other than the manufacturer’s service contract. If you purchased a ser- vice contract that is not a manufacturer’s service contract, and you req...

  • Page 547

    Mopar® parts mopar® fluids, lubricants, parts, and accessories are available from an authorized dealer. They are recom- mended for your vehicle in order to help keep the vehicle operating at its best. Reporting safety defects in the 50 united states and washington, d.C. If you believe that your vehi...

  • Page 548

    Publication order forms to order the following manuals, you may use either the website or the phone numbers listed below. Visa, mas- tercard, american express, and discover orders are ac- cepted. If you prefer mailing your payment, please call for an order form. Note: a street address is required wh...

  • Page 549

    Call toll free at: • 1-800-890-4038 (u.S.) • 1-800-387-1143 (canada) or visit us on the worldwide web at: • www.Techauthority.Com department of transportation uniform tire quality grades the following tire grading categories were established by the national highway traffic safety administration. The...

  • Page 550

    Warning! The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics. Temperature grades the temperature grades are a (the highest), b, and c, representing the tire’s resistan...

  • Page 551: Index

    Index 10

  • Page 552

    Abs (anti-lock brake system) . . . . . . . . . . . . . . . .361 adding engine coolant (antifreeze) . . . . . . . . . . . .497 adding fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . .413 adding washer fluid . . . . . . . . . . . . . . . . . . . . . .491 additives, fuel . . . . . . . . . ...

  • Page 553

    Anti-lock warning light . . . . . . . . . . . . . . . . . . . .218 appearance care . . . . . . . . . . . . . . . . . . . . . . . . .509 assistance towing. . . . . . . . . . . . . . . . . . . . . . . . .129 automatic dimming mirror . . . . . . . . . . . . . . . . . .110 automatic door locks . . . . ....

  • Page 554

    Capacities, fluid . . . . . . . . . . . . . . . . . . . . . . . . . .526 caps, filler fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .413 oil (engine) . . . . . . . . . . . . . . . . . . . . . . . . . . .477 power steering . . . . . . . . . . . . . . . . . . . . . . . . .356 ra...

  • Page 555

    Clean air gasoline . . . . . . . . . . . . . . . . . . . . . . . .410 cleaning wheels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .512 climate control . . . . . . . . . . . . . . . . . . . . . . . . . .302 clock. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .248 cl...

  • Page 556

    Defroster, rear window. . . . . . . . . . . . . . . . . . . . .209 defroster, windshield . . . . . . . . . . . . . . . . . . . . . .102 delay (intermittent) wipers . . . . . . . . . . . . . . . . . .174 diagnostic system, onboard . . . . . . . . . . . . . . . . .479 dimmer switch, headlight. . . . ....

  • Page 557

    Air cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . .486 block heater . . . . . . . . . . . . . . . . . . . . . . . . . .324 break-in recommendations . . . . . . . . . . . . . . . . .99 checking oil level . . . . . . . . . . . . . . . . . . . . . .483 coolant (antifreeze) . . . . . . . ....

  • Page 558

    Power steering . . . . . . . . . . . . . . . . . . . . . . . . .356 fluids, lubricants and genuine parts . . . . . . . . . . .527 fog lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .168 folding rear seat . . . . . . . . . . . . . . . . . . . . . . . . .162 folding rear seat (sedan)...

  • Page 559

    Gear select lever override . . . . . . . . . . . . . . . . . .468 general information . . . . . . . . . . . . . . . . . . . . . . .145 glass cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . .514 gross axle weight rating . . . . . . . . . . . . . . . . . . .419 gross vehicle weight rating...

  • Page 560

    Integrated power module (fuses) . . . . . . . . . . . . . .517 interior appearance care. . . . . . . . . . . . . . . . . . . .513 intermittent wipers (delay wipers). . . . . . . . . . . . .174 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 ipod®/usb/mp3 control bluetooth® ...

  • Page 561

    Cargo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .203 center mounted stop . . . . . . . . . . . . . . . . . . . .525 daytime running . . . . . . . . . . . . . . . . . . . . . . .168 dimmer switch, headlight . . . . . . . . . . . . . . . . .167 engine temperature warning . . . . . . ...

  • Page 562

    Lumbar support . . . . . . . . . . . . . . . . . . . . . . . . . .157 maintenance free battery. . . . . . . . . . . . . . . . . . . .487 maintenance procedures . . . . . . . . . . . . . . . . . . . .482 maintenance schedule . . . . . . . . . . . . . . . . . . . . . .532 malfunction indicator light (...

  • Page 563

    Oil change indicator . . . . . . . . . . . . . . . . . . . . . . .237 oil change indicator, reset . . . . . . . . . . . . . . . . . .237 oil, engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .483 capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . .526 change interval . ...

  • Page 564

    Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35 power steering fluid. . . . . . . . . . . . . . . . . . . . . . .529 power transfer unit . . . . . . . . . . . . . . . . . . . . . . .509 pregnant women and seat belts . . . . . . . . . . . . . . .54 preparation for jacking . . . ...

  • Page 565

    Restraints, child. . . . . . . . . . . . . . . . . . . . . . . . . . .77 retractable cargo area cover . . . . . . . . . . . . . . . .203 roll over warning . . . . . . . . . . . . . . . . . . . . . . . . . .4 roof type carrier . . . . . . . . . . . . . . . . . . . . . . . . .210 rotation, tires . . ....

  • Page 566

    Untwisting procedure . . . . . . . . . . . . . . . . . . . . .52 seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .151 adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . .151 heated . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .154 lumbar support . ....

  • Page 567

    Starting procedures . . . . . . . . . . . . . . . . . . . . . . . .321 steering power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .356 tilt column . . . . . . . . . . . . . . . . . . . . . . . . . . .176 storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .522 stora...

  • Page 568

    Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . .397 rotation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .399 safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .374 sizes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .376 snow tires . ....

  • Page 569

    Tread wear indicators . . . . . . . . . . . . . . . . . . . . . .395 trip computer . . . . . . . . . . . . . . . . . . . . . . . . . . .232 trip odometer . . . . . . . . . . . . . . . . . . . . . . . . . . .218 trip odometer reset button. . . . . . . . . . . . . . . . . .218 turn signals . . . . . ....

  • Page 570

    Vehicle security alarm (security alarm) . . . . . . . . . .18 vehicle storage . . . . . . . . . . . . . . . . . . . . . . . . . . .313 voice command commands . . . . . . . . . . . . . . . . . . . . . . . . . . . .147 system operation . . . . . . . . . . . . . . . . . . . . . . .145 voice training . ...

  • Page 571

    Installation of radio transmitting equipment special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained person- nel. The following must be obs...

  • Page 572

    Patriot o w n e r ’ s m a n u a l 20 15 p a triot 15mk74-126-ad fourth edition printed in u.S.A. 2 0 1 5 fca us llc.