1. DL manuals
  2. Jeep
  3. Automobile
  4. RENEGADE 2016
  5. Owner's Manual

Jeep RENEGADE 2016 Owner's Manual

Other manuals for RENEGADE 2016: User Manual

Summary of RENEGADE 2016

  • Page 1

    Renegade o w n e r ’ s m a n u a l 20 16 r enegade first edition rev 1 printed in u.S.A. 16bu-126-aa ©2015 fca us llc. All rights reserved. Jeep is a registered trademark of fca us llc. 2 0 1 6 stick with the specialists ®.

  • Page 2

    Vehicles sold in canada with respect to any vehicles sold in canada, the name fca us llc shall be deemed to be deleted and the name fca canada inc. Used in substitution therefore. Driving and alcohol drunken driving is one of the most frequent causes of accidents. Your driving ability can be serious...

  • Page 3

    Table of contents section page 1 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 customer assistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Page 5

    Introduction contents 䡵 introduction . . . . . . . . . . . . . . . . . . . . . . . .4 䡵 how to use this manual . . . . . . . . . . . . . .5 䡵 warnings and cautions . . . . . . . . . . . . . .7 䡵 vehicle modifications/alterations . . . .7 䡵 rollover warning . . . . . . . . . . . . . . . . . . .7 1.

  • Page 6

    Introduction congratulations on selecting your new fca us llc vehicle. Be assured that it represents precision workman- ship, distinctive styling, and high quality - all essentials that are traditional to our vehicles. This is a specialized utility vehicle. It can go places and perform tasks that co...

  • Page 7

    Read these publications carefully. Following the instruc- tions and recommendations in this manual will help assure safe and enjoyable operation of your vehicle. Note: after reviewing the owner information, it should be stored in the vehicle for convenient referenc- ing and remain with the vehicle w...

  • Page 8

    6 introduction.

  • Page 9

    Warnings and cautions this owner’s manual contains warnings against operating procedures that could result in a collision, bodily injury and/or death. It also contains cautions against procedures that could result in damage to your vehicle. If you do not read this entire owner’s manual, you may miss...

  • Page 10

    Do not attempt sharp turns, abrupt maneuvers, or other unsafe driving actions that can cause loss of vehicle control. Failure to operate this vehicle safely may result in a collision, rollover of the vehicle, and severe or fatal injury. Drive carefully. Failure to use the driver and passenger seat b...

  • Page 11

    Customer assistance contents 䡵 suggestions for obtaining service for your vehicle . . . . . . . . . . . . . . . . . . . . . . . .11 ▫ prepare for the appointment . . . . . . . . . . . . .11 ▫ prepare a list . . . . . . . . . . . . . . . . . . . . . . . . .11 ▫ be reasonable with requests . . . . . ....

  • Page 12

    ▫ treadwear . . . . . . . . . . . . . . . . . . . . . . . . . . .17 ▫ traction grades. . . . . . . . . . . . . . . . . . . . . . . .17 ▫ temperature grades . . . . . . . . . . . . . . . . . . . .18 10 customer assistance.

  • Page 13

    Suggestions for obtaining service for your vehicle prepare for the appointment if you are having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty. Discuss additional charges with the service manager....

  • Page 14

    Facilities, factory-trained technicians, special tools, and the latest information to ensure the vehicle is fixed correctly and in a timely manner. This is why you should always talk to an authorized dealer service manager first. Most matters can be re- solved with this process. • if for some reason...

  • Page 15

    In mexico contact av. Prolongacion paseo de la reforma, 1240 sante fe c.P. 05109 mexico, d. F. In mexico city: 5081-7568 outside mexico city: 1-800-505-1300 puerto rico and u.S. Virgin islands customer service chrysler international services llc p.O. Box 191857 san juan 00919-1857 tel.: (787) 782-57...

  • Page 16

    Warranty expires. The manufacturer stands behind only the manufacturer’s service contracts. If you purchased a manufacturer’s service contract, you will receive plan provisions and an owner identification card in the mail within three weeks of the vehicle delivery date. If you have any questions abo...

  • Page 17

    Warranty information see the warranty information booklet, located on the dvd, for the terms and provisions of fca us llc warranties applicable to this vehicle and market. Reporting safety defects in the 50 united states and washington, d.C. If you believe that your vehicle has a defect that could c...

  • Page 18

    Publication order forms to order the following manuals, you may use either the website or the phone numbers listed below. Visa, mas- tercard, american express, and discover orders are ac- cepted. If you prefer mailing your payment, please call for an order form. Note: a street address is required wh...

  • Page 19

    Call toll free at: • 1-800-890-4038 (u.S.) • 1-800-387-1143 (canada) or visit us on the worldwide web at: • www.Techauthority.Com department of transportation uniform tire quality grades the following tire grading categories were established by the national highway traffic safety administration. The...

  • Page 20

    Warning! The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics. Temperature grades the temperature grades are a (the highest), b, and c, representing the tire’s resistan...

  • Page 21

    Graphical table of contents contents 䡵 front view . . . . . . . . . . . . . . . . . . . . . . . . . .20 ▫ front view (trailhawk) . . . . . . . . . . . . . . . . . .21 䡵 rear view . . . . . . . . . . . . . . . . . . . . . . . . . . .22 ▫ rear view (trailhawk) . . . . . . . . . . . . . . . . . . .23 䡵...

  • Page 22

    Front view front view 1 — headlights 2 — engine compartment 3 — windshield 4 — doors 5 — exterior mirrors 6 — wheels 20 graphical table of contents.

  • Page 23

    Front view (trailhawk) front view (trailhawk) 1 — headlights 2 — engine compartment 3 — windshield 4 — doors 5 — exterior mirrors 6 — wheels 3 graphical table of contents 21.

  • Page 24

    Rear view rear view 1 — rear lights 2 — rear windshield wiper 3 — liftgate 22 graphical table of contents.

  • Page 25

    Rear view (trailhawk) rear view (trailhawk) 1 — rear lights 2 — rear windshield wiper 3 — liftgate 3 graphical table of contents 23.

  • Page 26

    Instrument panel instrument panel 1 — headlight switch 2 — air vents 3 — instrument cluster 4 — multifunction lever 5 — windshield wiper lever 6 — air vents 7 — hand grip 8 — glove compartment 9 — steering wheel 24 graphical table of contents.

  • Page 27

    Interior interior features 1 — seats 2 — power window switches 3 — transmission shift lever (automatic/manual options) 4 — selec-terrain mode knob — if equipped 5 — climate controls 6 — switch panel 7 — uconnect radio 3 graphical table of contents 25.

  • Page 29

    Getting to know your vehicle contents 䡵 keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 ▫ key fob with remote control . . . . . . . . . . . . .31 䡵 ignition switch . . . . . . . . . . . . . . . . . . . . .39 ▫ operation . . . . . . . . . . . . . . . . . . . . . . . . . . . .39...

  • Page 30

    ▫ to disarm the system. . . . . . . . . . . . . . . . . . .52 ▫ disabling . . . . . . . . . . . . . . . . . . . . . . . . . . . .53 䡵 doors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53 ▫ manual door locks. . . . . . . . . . . . . . . . . . . . .53 ▫ central lock/unlock. . . . . . . ...

  • Page 31

    ▫ mode of operation . . . . . . . . . . . . . . . . . . . . .92 ▫ blind spot monitoring fault warnings . . . . . . .93 ▫ general information . . . . . . . . . . . . . . . . . . . .93 䡵 exterior lights . . . . . . . . . . . . . . . . . . . . . .94 ▫ headlights . . . . . . . . . . . . . . . . . . . . ...

  • Page 32

    ▫ manual climate controls — if equipped . . . . .115 ▫ automatic climate controls — if equipped . .119 䡵 my sky sun roof — if equipped . . . . . . .132 ▫ removable roof — if equipped . . . . . . . . . . .132 ▫ power my sky — if equipped . . . . . . . . . . . .133 ▫ removing and installing panels . ....

  • Page 33

    Keys your vehicle uses either a key start ignition system or keyless ignition system. The key start ignition system consists of a key fob with a remote keyless entry (rke) transmitter and an ignition node module (ignm). The keyless ignition system consists of a key fob with remote keyless entry (rke...

  • Page 34

    Key fob with remote control and integrated vehicle key the key fob with remote control contains the rke transmitter with an integrated vehicle key. To use the vehicle key, simply push the vehicle key release button. Keyless enter-n-go key fob emergency key release 1 — emergency key release button 2 ...

  • Page 35

    General information the following regulatory statement applies to all radio frequency (rf) devices equipped in this vehicle: this device complies with part 15 of the fcc rules and with industry canada license-exempt rss standard(s). Operation is subject to the following two conditions: 1. This devic...

  • Page 36

    Note: if the vehicle is equipped with passive entry, refer to “keyless enter-n-go” in “getting to know your vehicle” for further information. To lock the doors and liftgate if equipped, the doors may be locked by inserting the vehicle key into the exterior driver’s door lock cylinder. Push and relea...

  • Page 37

    • for more information, refer to “electronic vehicle information center (evic)/ driver information dis- play (did)” in “getting to know your instrument cluster” or “uconnect settings” in “multimedia.” replacing the battery in the key fob with remote control the recommended replacement battery is one...

  • Page 38

    2. Remove the battery by turning the back cover over (battery facing downward) and tapping it lightly on a solid surface such as a table or similar surface. Then, replace the battery. When replacing the battery, match the + sign on the battery to the + sign on the inside of the battery clip, located...

  • Page 39

    Separating keyless enter-n-go transmitter case 1. Remove the emergency key by sliding the mechanical latch on the back of the rke transmitter sideways with your thumb. Then, pull the key out with your other hand. 2. Separating rke halves requires screw removal (if equipped) and gently prying the two...

  • Page 40

    3. Remove the battery by turning the back cover over (battery facing downward) and tapping it lightly on a solid surface such as a table or similar surface. Then, replace the battery. When replacing the battery, match the + sign on the battery to the + sign on the inside of the battery clip, located...

  • Page 41

    Programming additional transmitters programming key fobs or rke transmitters may be performed at an authorized dealer. Request for additional key fobs note: only key fobs that are programmed to the vehicle electronics can be used to start and operate the vehicle. Once a key fob is programmed to a ve...

  • Page 42

    Keyless ignition system consists of a key fob with remote keyless entry (rke) transmitter and a keyless ignition node (kin). Models with integrated vehicle key the ignition node module (ignm) operates similar to an ignition switch. It has three operating positions, two with detents and one that is s...

  • Page 43

    • some electrical devices (e.G. Power locks, alarm, etc.) are still available. 2 — mar/run • driving position. • electrical devices are available. 3 — avv/start • start the engine. The ignition switch is provided with a safety mechanism. If the engine fails to start, the ignition should be returned ...

  • Page 44

    Note: if the ignition switch does not change with the push of a button, the rke transmitter (key fob) may have a low or dead battery. In this situation, a back up method can be used to operate the ignition switch. Put the nose side (side opposite of the emergency key) of the key fob against the engi...

  • Page 45

    • some electrical devices (e.G. Central locking, alarm, etc.) are still available. Run • driving position. • all the electrical devices are available. Start • start the engine. Note: the vehicle will not start if the fobik (key fob) is located inside the cargo area and the liftgate is opened. Warnin...

  • Page 46

    Caution! An unlocked car is an invitation. Always remove key from the ignition and lock all doors when leaving the vehicle unattended. Note: for further information, refer to ⬙starting the engine, ⬙ in ⬙starting and operating.⬙ general information the following regulatory statement applies to all ra...

  • Page 47

    Note: • the vehicle must be equipped with an automatic transmission to be equipped with remote start. • obstructions between the vehicle and rke transmitter may reduce this range. Remote start cancel message — if equipped the following messages will display in the instrument cluster if the vehicle f...

  • Page 48

    • rke panic button not pushed • system not disabled from previous remote start event • vehicle alarm system indicator flashing • ignition in stop/off position • fuel level meets minimum requirement • vehicle security alarm is not signaling an intrusion warning! • do not start or run an engine in a c...

  • Page 49

    • for security, power window operation is disabled when the vehicle is in the remote start mode. To exit remote start mode without driving the vehicle push and release the remote start button one time or allow the engine to run for the entire 15-minute cycle. Note: to avoid unintentional shutdowns, ...

  • Page 50

    Turn on in cold weather. These features will stay on through the duration of remote start or until the ignition switch is cycled to the mar/run position. Note: the remote start comfort system can be acti- vated and deactivated through the uconnect settings. For more information on remote start comfo...

  • Page 51

    Sentry key the sentry key immobilizer system prevents unauthor- ized vehicle operation by disabling the engine. The system does not need to be armed or activated. Operation is automatic, regardless of whether the vehicle is locked or unlocked. The system uses a key fob with a factory-mated remote ke...

  • Page 52

    General information the following regulatory statement applies to all radio frequency (rf) devices equipped in this vehicle: this device complies with part 15 of the fcc rules and with industry canada licence-exempt rss standard(s). Operation is subject to the following two conditions: 1. This devic...

  • Page 53

    To arm the system follow these steps to arm the vehicle security alarm: 1. Make sure the vehicles ignition is cycled to the stop/ off position (refer to ⬙starting the engine⬙ in ⬙start- ing and operating ⬙ for further information). • for vehicles equipped with keyless enter-n-go, make sure the vehic...

  • Page 54

    Same exterior zone (for further information, refer to ⬙keyless enter-n-go⬙ in ⬙getting to know your vehicle”). • push the lock button on the remote keyless entry (rke) transmitter. 3. If any doors are open, close them. Note: • if a second chime is heard after approximately four seconds from arming t...

  • Page 55

    Note: • the driver’s door key cylinder cannot arm or disarm the vehicle security alarm. • when the vehicle security alarm is armed, the interior power door lock switches will not unlock the doors. The vehicle security alarm is designed to protect your vehicle. However, you can create conditions wher...

  • Page 56

    Locking/unlocking doors from outside with the doors closed, insert the key blade into the driver exterior door lock cylinder and turn to the right to lock the driver’s door. To unlock the driver’s door, insert the key blade into the driver exterior door lock cylinder and turn to the left to unlock t...

  • Page 57

    Warning! • for personal security and safety in the event of a collision, lock the vehicle doors before you drive as well as when you park and leave the vehicle. • when leaving the vehicle, always remove the key fob from the vehicle and lock your vehicle. Unsu- pervised use of vehicle equipment may c...

  • Page 58

    The doors can also be locked and unlocked with the keyless enter-n-go (passive entry) system if equipped. Refer to “keyless enter-n-go” in “getting to know your vehicle” for further information. The power locks will continue to operate while the ignition is in the mar/run and stop/off position. If a...

  • Page 59

    Note: • passive entry can be enabled or disabled. Refer to “uconnect settings” in “multimedia” for further information. • if wearing gloves on your hands, or if it has been raining on the passive entry door handle, the unlock sensitivity can be affected, resulting in a slower re- sponse time. • if t...

  • Page 60

    To unlock from the passenger side with a valid passive entry rke transmitter within 5 ft (1.5 m) of the passenger door handle, grab the front passenger door handle to unlock all four doors and the liftgate automatically. Note: all doors will unlock when the front passenger door handle is grabbed reg...

  • Page 61

    Note: the passive entry system will not operate if the rke transmitter battery is dead. The vehicle doors can also be locked by using the lock button located on the vehicle’s interior door panel. Preventing inadvertent locking of passive entry rke transmitter in vehicle (fobik-safe) to minimize the ...

  • Page 62

    When any of these situations occur, after all open doors are shut, the fobik-safe search will be executed. If it finds a passive entry rke transmitter inside the car, and it does not find any passive entry rke transmitters outside the car, then the car will unlock and alert the customer. Note: the v...

  • Page 63

    Note: if “unlock all doors 1st press” is programmed in evic/did, if equipped, only the liftgate will unlock when you push the electronic release. If ⬙unlock driver door 1st press ⬙ is programmed in uconnect, the liftgate will unlock when you push the electronic lock/unlock button on the liftgate. Fo...

  • Page 64

    Note: the emergency key can be inserted into the door lock cylinder from either direction. Warning! • never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be sever...

  • Page 65

    General information the following regulatory statement applies to all radio frequency (rf) devices equipped in this vehicle: this device complies with part 15 of the fcc rules and with industry canada licence-exempt rss standard(s). Operation is subject to the following two conditions: 1. This devic...

  • Page 66

    Note: • when the child lock system is engaged, the door can only be opened by using the outside door handle even though the inside door lock is in the unlocked position. • after disengaging the child-protection door lock system, always test the door from the inside to make certain it is in the desir...

  • Page 67

    Warning! Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child-protection locks are engaged. Seats seats are a part of the occupant restraint system of the vehicle. Warning! • it is dangerous to ride in a cargo area, inside...

  • Page 68

    Manual front seats manual front seat forward/rearward adjustment on models equipped with manual seats, the adjusting bar is located at the front of the seats, near the floor. While sitting in the seat, lift up on the bar and move the seat forward or rearward. Release the bar once you have reached th...

  • Page 69

    Warning! (continued) chest. In a collision you could slide under the seat belt and be seriously or even fatally injured. Use the recliner only when the vehicle is parked. Height adjustment the driver’s seat height can be raised or lowered by using a lever, located on the outboard side of the seat. P...

  • Page 70

    Power adjustment (front) — if equipped the power seat controls are located on the outboard side of the seat, close to the floor. Use the switch to move the seat up/down, forward/ rearward, tilt if equipped and to set the angle of the seatback. Power seat switches 1 — power seat switch 2 — power recl...

  • Page 71

    Forward or rearward adjustment the seat can be adjusted both forward and rearward. Push the seat switch forward or rearward, the seat will move in the direction of the switch. Release the switch when the desired position has been reached. Height adjustment the height of the seats can be adjusted up ...

  • Page 72

    • push the heated seat button a second time to turn the lo setting on. • push the heated seat button a third time to turn the heating elements off. If the hi-level setting is selected, the system will auto- matically switch to lo-level after approximately 145 minutes of continuous operation. At that...

  • Page 73

    Note: • prior to folding the rear seat down, it may be necessary to position the front seat to its mid-track position. Be sure that the front seats are fully upright and posi- tioned forward, this will allow the rear seat to fold down easily. • prior to folding the rear seat, you must secure the rea...

  • Page 74

    Removing shelf — if equipped proceed as follows: 1. Disconnect the two links that support the shelf at the eyelets. 2. Lift the rear part of the overhead luggage shelf. 3. Clear the pins placed outside of the shelf, and then remove the rear shelf pulling it upwards. 4. The rear shelf can be stored i...

  • Page 75

    Partial enlargement of cargo area enlargement of the left side of the cargo area allows you to carry a single passenger on the right side of the rear seat, while the enlargement of the right side allows you to carry two passengers. Proceed as follows: 1. Remove the rear shelf (if equipped). 2. Fully...

  • Page 76

    4. Pull the seatback release lever to fold the left or right rear seatback completely forward. Cargo area enlargement folding both sides of the rear seat provides additional storage in the rear cargo area. Proceed as follows: 1. Fully lower the rear seat head restraints. 2. Move the safety belts to ...

  • Page 77

    2. Lift the seatbacks, pushing them back until they lock on both the latches. Verify the red notches are no longer visible on the release lever. If the red notches are visible, the seatback is not secure. Unfolding the rear armrest 40/20/40 tilt the head restraint forward and pull the rear armrest t...

  • Page 78

    Warning! Be certain that the seatback is securely locked into position. If the seatback is not securely locked into position the seat will not provide the proper stability for child seats and/or passengers. An improperly latched seat could cause serious injury. Head restraints head restraints are de...

  • Page 79

    Warning! The head restraints for all occupants must be prop- erly adjusted prior to operating the vehicle or occu- pying a seat. Head restraints should never be ad- justed while the vehicle is in motion. Driving a vehicle with the head restraints improperly adjusted or removed could cause serious in...

  • Page 80

    Warning! The head restraints for all occupants must be prop- erly adjusted prior to operating the vehicle or occu- pying a seat. Head restraints should never be ad- justed while the vehicle is in motion. Driving a vehicle with the head restraints improperly adjusted or removed could cause serious in...

  • Page 81

    Note: the head restraints should only be removed by qualified technicians, for service purposes only. If either of the head restraints require removal, see your autho- rized dealer. Steering wheel tilt/telescoping steering column this feature allows you to tilt the steering column upward or downward...

  • Page 82

    To lock the steering column in position, pull the tilt/ telescoping lever upward until fully engaged. Warning! Do not adjust the steering column while driving. Adjusting the steering column while driving or driv- ing with the steering column unlocked, could cause the driver to lose control of the ve...

  • Page 83

    Warning! (continued) • do not place anything on the steering wheel that insulates against heat, such as a blanket or steering wheel covers of any type and material. This may cause the steering wheel heater to overheat. Mirrors inside day/night mirror the mirror can be adjusted up, down, left, and ri...

  • Page 84

    Off by pushing the button at the base of the mirror. A light to the left of the button will illuminate to indicate when the dimming feature is activated. The sensor to the right of the button does not illuminate. Note: this feature is disabled when the vehicle is moving in reverse. Outside mirrors p...

  • Page 85

    Manual adjustment mirrors — if equipped to adjust the exterior mirrors, push the corners of the mirrors till desired alignment is obtained. Power mirror switch 1 — mirror selector switch 2 — mirror adjustment switch manual adjustment mirror 4 getting to know your vehicle 83.

  • Page 86

    Folding mirror the exterior mirrors are hinged to allow the mirror to pivot forward or rearward to help avoid damage. The mirror has three detent positions: full forward, normal and full rearward. Heated mirrors — if equipped these mirrors are heated to melt frost or ice. This feature can be activat...

  • Page 87

    When the vehicle is started, the bsm warning light will momentarily illuminate in both outside rear view mirrors to let the driver know that the system is operational. The bsm system sensors operate when the vehicle is in any forward gear or reverse and enters stand-by mode when the vehicle is in pa...

  • Page 88

    The area on the rear fascia where the radar sensors are located must remain free of snow, ice, and dirt/road contamination so that the bsm system can function properly. Do not block the radar sensors located on the rear fascia with foreign objects (bumper stickers, bicycle racks, etc.). The bsm syst...

  • Page 89

    The bsm system monitors the detection zone from three different entry points (side, rear, front) while driving to see if an alert is necessary. The bsm system will issue an alert during these types of zone entries. Entering from the side vehicles that move into your adjacent lanes from either side o...

  • Page 90

    Entering from the rear vehicles that come up from behind your vehicle on either side and enter the rear detection zone with a relative speed of less than 31 mph (50 km/h). Overtaking traffic if you pass another vehicle slowly with a relative speed less than 15 mph (25 km/h) and the vehicle remains i...

  • Page 91

    The bsm system is designed not to issue an alert on stationary objects such as guardrails, posts, walls, foliage, berms, etc. However, occasionally the system may alert on such objects. This is normal operation and your vehicle does not require service. Overtaking/passing stationary objects 4 gettin...

  • Page 92

    The bsm system will not alert you of objects that are traveling in the opposite direction of the vehicle in adjacent lanes. Warning! The blind spot monitoring system is only an aid to help detect objects in the blind spot zones. The bsm system is not designed to detect pedestrians, bicy- clists, or ...

  • Page 93

    Rcp monitors the rear detection zones on both sides of the vehicle, for objects that are moving toward the side of the vehicle with a minimum speed of approximately 1 mph (2 km/h), to objects moving a maximum of approximately 22 mph (35 km/h), such as in parking lot situations. Note: in a parking lo...

  • Page 94

    Mode of operation three selectable modes of operation are available in the uconnect system. Refer to “uconnect settings” in “mul- timedia” for further information. Blind spot alert lights only when operating in blind spot alert mode, the bsm system will provide a visual alert in the appropriate side...

  • Page 95

    Note: the bsm system will store the current operating mode when the vehicle is shut off. Each time the vehicle is started the previously stored mode will be recalled and used. Blind spot monitoring fault warnings sensor blinded in the case of a sensor blinded: • bsm mirror warning lights are turned ...

  • Page 96

    Operation is subject to the following two conditions: 1. The device may not cause harmful interference. 2. The device must accept any interference received, including interference that may cause undesired op- eration of the device. Changes or modifications to any of these systems by other than an au...

  • Page 97

    Automatic lighting — if equipped light sensor the light sensor is equipped with an infrared led, located on the windshield. It detects changes in light intensity outside the vehicle, based on the sensitivity of light set by using the menu on the display or on the uconnect system. The higher the sens...

  • Page 98

    Front fog lights — if equipped the front fog light switch is built into the headlight switch. To activate the front fog lights, turn on the parking lights or the low beam headlights and push the fog light button on the headlight switch. To turn off the front fog lights, push the fog light button on ...

  • Page 99

    Headlight delay disable the feature is disabled by turning on the headlights, the parking lights or by placing the ignition in the mar/ run position. If you shut off the lights before the ignition is turned on, they will turn off in the normal manner. Note: the lights must be turned off within two m...

  • Page 100

    Note: the headlights must be on for the high beams to activate. Turn signals move the multifunction lever up or down and the arrows on each side of the instrument cluster flash to show proper operation of the front and rear turn signal lights. Note: when the daytime running lights are on and a turn ...

  • Page 101

    To operate the courtesy lights, push either the drivers or passenger light switch. Note: • before exiting the vehicle, make sure that the interior lights are turned off. This will prevent the battery from discharging once the doors are closed. • if a light is left on it will automatically be turned ...

  • Page 102

    Rear lights push the button on the rear dome light once to turn the light on, the light will remain on at all times. Push the button a second time to turn the light off, the lights will remain off at all times. Vehicles with retractable roof for vehicles equipped with a retractable roof, there are t...

  • Page 103

    The lights come on by opening any of the doors. Dome light timing the dome light will automatically illuminate when the doors are unlocked, the doors are opened or after the doors are closed. Timing entering the vehicle the dome lights illuminate in the following ways: • when the doors are unlocked,...

  • Page 104

    The dome light will turn off under any of the following conditions: • the dome light is disabled when the ignition is placed in the mar/run or avv/start position. • the dome lights will turn off automatically when the doors are locked. • the dome lights will automatically turn off after approximatel...

  • Page 105

    The mirror cover upward. The lights will turn on auto- matically. Closing the mirror cover will turn the light off. Interior lights dimmer switch rotate the ambient dimmer control upward or down- ward to increase or decrease the brightness of the ambi- ent light located in the overhead console, door...

  • Page 106

    Wipers and washers the windshield wiper/washer controls are located on the lever on the right side of the steering column. The front wipers are operated by rotating a switch, located on the end of the lever. Headlight switch 1 — ambient light control 2 — instrument panel dimmer windshield wiper stal...

  • Page 107

    Caution! Always remove any buildup of snow that prevents the windshield wiper blades from returning to the “park” position. If the windshield wiper switch is turned off, and the blades cannot return to the “park” position, damage to the wiper motor may occur. Front wiper operation rotate the windshi...

  • Page 108

    Mist use this feature when weather conditions make occa- sional usage of the wipers necessary. Push the lever upward to the mist position and release for a single wiping cycle. Note: the mist feature does not activate the washer pump; therefore, no washer fluid will be sprayed on the windshield. The...

  • Page 109

    The sensitivity of the system can be adjusted with the multifunction lever. Wiper delay position one is the least sensitive, and wiper delay position two is the most sensitive. Place the wiper switch in the off position when not using the system. Rain sensing wipers – inhibition when the user switch...

  • Page 110

    Rear wiper operation the rear wiper/washer controls are located on the lever on the right side of the steering column. The rear wiper/washer is operated by rotating a switch, located at the middle of the lever. Rotate the center portion of the lever upward to the first detent for intermittent operat...

  • Page 111

    Caution! Failure to follow these cautions can cause damage to the heating elements: • use care when washing the inside of the rear window. Do not use abrasive window cleaners on the interior surface of the window. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements....

  • Page 112

    Auto-on rear window defroster/windshield wiper de-icer— if equipped turning on the car, the rear window defroster and windshield wiper de-icer will automatically turn on when the outside ambient temperature is less than 40° f (4.4° c). The rear window defroster and windshield wiper de- icer automati...

  • Page 113

    The window controls will operate only when the ignition is in the mar/run or avv/start position. Note: for vehicles equipped with uconnect, the power window switches will remain active for up to three minutes after the ignition is cycled to the stop/off position. Opening either front door will cance...

  • Page 114

    Auto-up feature with auto-reverse protection — if equipped lift and hold the window switch for half a second, release, and the window will go up automatically. To stop the window from going all the way up during the auto operation, push down on the switch briefly. To partially close the window, lift...

  • Page 115

    Wind buffeting wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof in certain open or par- tially open positions. This is a normal occurrence and can be minimiz...

  • Page 116

    Center air outlets 1 — fixed air outlet 2 — air flow outlet adjustment 3 — air vane adjustment 4 — adjustable air outlet right side air outlets 1 — fixed air outlet 2 — adjustable air outlet 3 — air vane adjustment 4 — air flow outlet adjustment 114 getting to know your vehicle.

  • Page 117

    Manual climate controls — if equipped the manual climate controls consist of a series of rotary dials with inner push buttons. 1. Blower control rotate this control to regulate the amount of air forced through the ventilation system in any mode. The blower speed increases as you move the control clo...

  • Page 118

    3. Mode control rotate this control to change the system between modes (panel, bi-level, floor, mix, defrost). • panel air is directed through the outlets in the instrument panel. These outlets can be ad- justed to direct airflow. Note: the center instrument panel outlets can be ad- justed so that t...

  • Page 119

    4. Rear defrost button push and release the rear defrost control button to turn on the rear window defroster and the heated outside mirrors (if equipped). An indicator will illuminate when the rear window defroster is on. The rear window defroster automatically turns off after 20 minutes. 5. A/c but...

  • Page 120

    Activation of this function is indicated by the rear defrost indicator light on the instrument panel turning on. The function is automatically deactivated after 20 minutes. If equipped, push the rear defrost button to activate the defrosting of door mirrors and heated rear window. Caution! To avoid ...

  • Page 121

    Note: the system uses r-1234yf (refrigerant) which does not pollute the environment in the event of acciden- tal leakage. Under no circumstances is the use of r-134a (refrigerant) allowed. Automatic climate controls — if equipped 1. Driver temperature control provides the driver with independent tem...

  • Page 122

    When max defrost mode is selected, the air conditioning compressor is turned on (led on), both driver and passenger temperature controls are set to (hi), defrost mode is selected (led on), rear defroster is turned on (led on) and the air recirculation is turned off (led off). If the max defrost mode...

  • Page 123

    On the display. Turning the control knob completely in one direction or the other activates the ⬙hi⬙ (maximum heating) or ⬙lo⬙ (maximum cooling) functions shown in the display, respectively. To deactivate these functions, turn the temperature knob to the desired temperature. 9. Sync button push the ...

  • Page 124

    Note: • when in max defrost mode, the recirculation button will change the setting to normal defrost mode. This indicates that you can not enter to this mode due to fogging risk. • when the auto indicator is on and the recirculation indicator is off, the recirculation is in auto mode. If the recircu...

  • Page 125

    The automatically controlled functions are: • air temperature at the driver/front passenger side vents. • blower speed (continuous variation of the air flow). • compressor engagement (for cooling/dehumidifying the air). • air recirculation. All these functions can be adjusted manually by operat- ing...

  • Page 126

    • heated rear window • system deactivation note: the climate control system detects the passenger compartment temperature using a temperature sensor, located in the lower instrument panel between the center console and the steering wheel. Turning on the climate control system the climate control sys...

  • Page 127

    Push the sync button to align the air temperature between the two zones. Turn the passenger temperature control knob to return to the separate management of air temperatures in the two zones. Turning the control knobs completely in one direction or the other activates the ⬙hi⬙ (maximum heating) or ⬙...

  • Page 128

    • defrost and panel modes – air flow distribution between windshield defrosting diffusers and side and central instrument panel vents. • defrost, panel and floor modes – air flow distribution to all the diffusers. Note: air always flows from the side instrument panel diffusers: it is, however, possi...

  • Page 129

    Note: to restore automatic control of the fan speed after a manual adjustment, push the auto button. Auto button when the auto button is pushed (led illuminated), the climate control system automatically adjusts the follow- ing settings in the corresponding zones: • quantity and distribution of the ...

  • Page 130

    Turn the passenger temperature control knob to set the passenger side temperature and return to separate air temperature management. Air recirculation the air recirculation is managed by the following: • forced activation (air recirculation always on): indi- cated by the led on the recirculation con...

  • Page 131

    Climate control system compressor push the a/c control button to activate/deactivate the compressor (activation is indicated by the led on the button turning on). The system remembers that the compressor has been turned off, even after the engine has stopped. Pushing the a/c button will stop auto mo...

  • Page 132

    • directs air flow to windshield and front side window diffusers. • activates the heated rear window defrost. • activates the heated windshield (if equipped). • displays the fan speed (blower control indicator led illuminated). When the function is activated, the auto button led turns off. With the ...

  • Page 133

    Caution! To avoid causing damage to the rear window de- froster heating filaments do not affix stickers or other objects to the inside of the rear glass. Turning off the climate control system push the on/off button. With the climate control system off: • air recirculation is on, isolating the passe...

  • Page 134

    Note: the system uses r-1234yf (refrigerant) which does not pollute the environment in the event of acciden- tal leakage. Under no circumstances is the use of r-134a (refrigerant) allowed. My sky sun roof — if equipped removable roof — if equipped the roof consists of front and rear panels that can ...

  • Page 135

    On some vehicles the front panel can be power operated refer to “power my sky” in this section. Caution! The panels are able to withstand the snow. However, it is recommended that you remove excessive layers of snow that have accumulated or damage to the panels may occur. Power my sky — if equipped ...

  • Page 136

    To retract the front panel to the open position, push the open/close button. Front panel operation switch operation switch 1 — front panel open/close switch 2 — front panel vent switch 134 getting to know your vehicle.

  • Page 137

    From the fully open position, pull the open/close switch: the front panel will close completely. Venting the front panel to vent the front panel push and release the vent switch. During the vent operation any push on the open/close switch will stop the closing of the panel. Note: if the my sky is in...

  • Page 138

    Removing panels 1. Front panel must be in the closed position to remove panels. 2. Locate the my sky key inside the panel storage bag in the cargo area. 3. From inside of the passenger compartment, insert the my sky key into the latch key hole. My sky key latch key hole 136 getting to know your vehi...

  • Page 139

    4. Rotate and keep the key turned to the symbol to release the lock and pull the panel handle down and away from the stowed position, unlocking the panel. Rotating my sky key unlocking panel handle 4 getting to know your vehicle 137.

  • Page 140

    5. Remove the key from the latch key hole. 6. Remove the panel from the outside of the vehicle. Removing key push panel up 138 getting to know your vehicle.

  • Page 141

    7. Place the panel inside of the provided bag for storage in the cargo area. Repeat the process for the rear panel. Note: an air deflector is available on the jeep accessory line. This deflector may be used to avoid the “tunnel effect” inside the vehicle, if the front panel is removed. Installing pa...

  • Page 142

    4. From inside the vehicle, pull the handle down and toward the stowed position, locking it into place. Guide tabs closing panel handle 140 getting to know your vehicle.

  • Page 143

    5. Make sure that the panel has been properly refitted. From inside the passenger compartment, push up- ward on the panel from the bottom, in order to verify that it is properly latched to the clamping locks. Bag for housing panels — if equipped after the panels have been removed, store the roof pan...

  • Page 144

    For proper housing, proceed as follows: 1. Open the roof panel bag and lift the panel dividers toward the outside. 2. Place the first panel into the bag, fold the panel dividers and place the second panel into the bag. Roof panel bag panel dividers 142 getting to know your vehicle.

  • Page 145

    3. Close the bag and place it on the inside the cargo area. First panel in storage bag second panel in storage bag 4 getting to know your vehicle 143.

  • Page 146

    4. Open the velcro straps provided on the bag. Anchor them firmly at the tie-down hooks located in the cargo area. Note: • do not load objects that weigh over 165 pounds (75 kg) on top of the roof panel bag. • the bag is washable. Refer to the documentation that is supplied with the bag. Tie-down ho...

  • Page 147

    Emergency open/close if the power my sky switch fails, the retractable roof can be operated manually as follows: 1. Remove the protective cap located on the inner lining. 2. Remove the allen key or my sky key that is supplied in the tool bag in the cargo area. 3. Insert the allen key or my sky key i...

  • Page 148

    Caution! • when refitting panels, be careful to avoid fingers, scarves, ties and items of clothing from getting caught under the panels themselves. • do not open the roof in the presence of snow or ice. There is risk of damage. Hood opening two latches must be released to open the hood. Pull the hoo...

  • Page 149

    Move to the outside of the vehicle and push the safety latch release lever toward the passenger side of the vehicle. The hood release lever is located behind the center front edge of the hood. Remove the support rod from the locking tab and insert it into the seat located on the underside of the hoo...

  • Page 150

    Closing hold up the hood with one hand and with the other hand remove the support rod from its seat and reinsert it into the locking tab. Lower the hood to approximately 6 inches (15 cm) from the engine compartment and drop it. Make sure that the hood is completely closed. Caution! To prevent possib...

  • Page 151

    Warning! Be sure the hood is fully latched before driving your vehicle. If the hood is not fully latched, it could open when the vehicle is in motion and block your vision. Failure to follow this warning could result in serious injury or death. Liftgate opening to unlock the liftgate, use the remote...

  • Page 152

    The liftgate passive entry unlock feature is built into the electronic liftgate release. With a valid passive entry rke transmitter within 3 ft (1.0 m) of the liftgate, push the electronic liftgate release to open with one fluid motion. To open the liftgate, squeeze the electronic liftgate release a...

  • Page 153

    Emergency opening proceed as follows: 1. Remove the rear shelf (if equipped). 2. Fold the rear seats forward. 3. Using the supplied screwdriver (located under cargo floor in tool kit), remove the yellow tab. Emergency opening tab location a — yellow tab 4 getting to know your vehicle 151.

  • Page 154

    4. Insert the screwdriver into the release tab slot to trigger the release tab of the liftgate. Closing grasp the liftgate closing handle and initiate lowering the liftgate. Release the handle when the liftgate takes over the closing effort. Emergency release tab slot location b — release tab slot 1...

  • Page 155

    Note: before closing the liftgate, make sure to be in possession of the key because the liftgate will be locked automatically. Cargo area features cargo load floor the vehicle is equipped with a load floor that can be adjusted as needed. Position 1 (lowered position): this position allows you to mak...

  • Page 156

    Table tilt load in addition to the two positions described above, the load floor can also be placed in a tilted position (slanted toward the rear seatbacks as to ease the access to the underlying zone of the luggage compartment (e.G. To pick up the spare tire or the tire service kit). Place the load...

  • Page 157

    Access to the loading floor to access the double load compartment, proceed as follows: 1. Lift up on the load floor handle. Table tilt load supports 1 — loading floor support one 2 — loading floor support two load floor handle 1 — cargo load floor 2 — cargo load floor handle 4 getting to know your v...

  • Page 158

    2. Place the desired objects inside the compartment. 3. Reposition the load floor. Caution! The load floor must be arranged in a central position with respect to cargo area. Displacement load floor to position the load from the lower to the upper position, proceed as follows: 1. Grasp the load floor...

  • Page 159

    Anchoring of the load the cargo tie-downs, located on the cargo area floor, should be used to safely secure loads when the vehicle is moving. The side panels maybe equipped with three grocery hooks (one on the left side and two on the right side) for securing loads that are not excessively heavy. Ti...

  • Page 160

    Rear power outlet the rear cargo power outlet is located on the left side of the cargo area. The outlet only works when the ignition is in the mar/run position. Grocery hooks rear 12 volt cargo power outlet 158 getting to know your vehicle.

  • Page 161

    Note: the rear cargo power outlet can be changed to “battery” powered all the time by switching the power outlet integrated power module 20a fuse from fuse location f18 to f30. Refer to “engine compartment fuses” in “in case of emergency” for further informa- tion. Caution! Do not connect devices wi...

  • Page 162

    Cargo box — if equipped the cargo area contains a preformed cargo box that can be used for the storage of objects that allows you to obtain a uniform level when loading. Note: the cargo box is sized for a maximum capacity of distributed weight equal to 242 lbs (110 kg). Cargo box 160 getting to know...

  • Page 163

    Internal equipment glove compartment the glove compartment is located on the passengers side of the instrument panel. To open the glove compartment proceed as follows: 1. Unlock the compartment using the vehicle key. 2. Pull the handle to open the compartment. Once the glove compartment is open, a l...

  • Page 164

    Note: • do not insert objects in the glove compartment that will not allow the compartment to fully close. • the glove compartment should be completely closed while the vehicle is in motion. Sun visors sun visors are located on both sides of the rearview mirror. The visors can be lowered or moved to...

  • Page 165

    Extendible sun visor to extend the sun visor, proceed as follows: 1. Place the sun visor against the door glass by detaching it from the hook and turning it toward the side window. 2. Slide the visor along the rod to provide coverage more to the rear. Sliding sun visor 1 — sun visor 4 getting to kno...

  • Page 166

    3. Slide out the sun visor extender for even more side coverage toward the rear. Power outlets the front power outlet is located under the center stack of the instrument panel. It only operates with the ignition in the mar/run position. Models equipped with the optional ⬙smoker kit,⬙ will have a cig...

  • Page 167

    Caution! Do not connect devices with power higher than 180 watts (15 amps) to the socket. Do not damage the socket by using unsuitable adaptors. If the 180 watt (15 amp) power rating is exceeded the fuse protect- ing the system will need to be replaced. Warning! To avoid serious injury or death: • o...

  • Page 168

    Power inverter — if equipped there is a 115 volt, 150 watt power inverter outlet located on the back of the center console to convert dc current to ac current. The power inverter can power cellular phones, electronics and other low power devices requir- ing up to 150 watts. Certain high-end video ga...

  • Page 169

    Inverter it will automatically reset. To avoid overloading the circuit, check the power ratings on electrical devices prior to using the power inverter. Warning! To avoid serious injury or death: • do not insert any objects into the receptacles. • do not touch with wet hands. • close the lid when no...

  • Page 170

    Warning! When the cigar lighter is in use it becomes very hot. To avoid serious injury, handle the cigar lighter with care. Always check that the cigar lighter has turned off. Caution! Do not connect devices with power higher than 180 watts (15 amps) to the socket. Do not damage the socket by using ...

  • Page 171

    Front armrest the front armrest is located between the front seats. The armrest can be adjusted by moving it in the direction indicated by the arrows. Push the storage handle and lift up the armrest to access the storage compartment. Front armrest handle storage compartment 4 getting to know your ve...

  • Page 172

    Warning! Do not operate this vehicle with a console compart- ment lid in the open position. Driving with the console compartment lid open may result in injury in a collision. Cupholders there are two cupholders for the front seat passengers, located in the center console. Front cupholders 170 gettin...

  • Page 173

    There are two cupholders located in the rear armrest if equipped. Handle grip the handle grip is located on the passenger side of the instrument panel. The handle can be used to enter or exit the vehicle or when traveling on rough terrain. Rear cupholders handle grip 4 getting to know your vehicle 1...

  • Page 174

    Roof luggage rack — if equipped your vehicle may be equipped with a roof luggage rack for transporting accessories. Crossbars should always be used whenever cargo is placed on the roof luggage rack. Check the straps frequently to be sure that the load remains securely attached. Note: crossbars can b...

  • Page 175

    Warning! Roof rack cargo must be securely tied down before driving your vehicle. Improperly secured loads may fall off the vehicle, particularly at high speeds, re- sulting in personal injury or property damage. Fol- low the roof luggage rack warnings and cautions when carrying cargo on your roof ra...

  • Page 177

    Getting to know your instrument cluster contents 䡵 instrument cluster . . . . . . . . . . . . . . . . .177 ▫ instrument cluster with multi-functional display (evic) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .177 ▫ instrument cluster with reconfigurable multi-functional display (did). ....

  • Page 178

    䡵 electronic vehicle information center (evic) / driver information display (did) . . . . . . . . . . . . . . . . . . . . . . . .213 ▫ evic/did description. . . . . . . . . . . . . . . . . .213 ▫ mapping and reconfigurable zone display (evic) — if equipped . . . . . . . . . . . . . . . . . .214 ▫ ma...

  • Page 179

    Instrument cluster instrument cluster with multi-functional display (evic) electronic vehicle information center (evic) cluster 1 — tachometer 2 — digital indicator engine coolant temperature warning light with maximum temperature 3 — multi-functional display 4 — digital indicator fuel level indicat...

  • Page 180

    Instrument cluster with reconfigurable multi-functional display (did) driver information display (did) cluster 1 — tachometer 2 — digital indicator engine coolant temperature 3 — multi-functional display 4 — digital indicator fuel level (the triangle symbol pointing toward the right indicates where ...

  • Page 181

    Speedometer (evic) indicates the speed of the vehicle in mph or km/h. Adjusting instrument panel illumination (light sen- sor) inside the speedometer, a light sensor detects ambient light conditions and adjusts the brightness of the instru- ment cluster. The instrument works as follows: • in ⬙day⬙ m...

  • Page 182

    • in ⬙night⬙ mode the display, the graphics, and the indexes are adjusted accordingly. Even the light inten- sity of the automatic dual zone climate control system and the uconnect system display speedometer (did) indicates the speed of the vehicle in mph or km/h. Adjusting instrument panel illumina...

  • Page 183

    • in ⬙night⬙ mode the display, the graphics, and the indexes are adjusted accordingly. Even the light inten- sity of the automatic dual zone climate control system and the uconnect system display odometer the odometer display shows the total distance the ve- hicle has been driven. U.S. Federal regul...

  • Page 184

    The gauge pointer will likely indicate a higher tempera- ture when driving in hot weather, up mountain grades, or when towing a trailer. It should not be allowed to exceed the upper limits of the normal operating range. In the normal use of the car, the digital scale may move in different positions....

  • Page 185

    Warning and indicator lights important: the warning / indicator lights switch on in the instrument panel together with a dedicated mes- sage and/or acoustic signal when applicable. These indications are indicative and precautionary and as such must not be considered as exhaustive and/or alternative ...

  • Page 186

    Red telltale indicator lights seat belt reminder warning light red telltale light what it means seat belt reminder warning light when the ignition switch is first turned to on/run, this light will turn on for four to eight seconds as a bulb check. During the bulb check, if the driver’s seat belt is ...

  • Page 187

    Air bag warning light red telltale light what it means air bag warning light this light will turn on for four to eight seconds as a bulb check when the ignition switch is first turned to on/run. If the light is either not on during startup, stays on, or turns on while driving, have the system inspec...

  • Page 188

    Brake warning light red telltale light what it means united states canada brake warning light this light monitors various brake functions, including brake fluid level and parking brake application. If the brake light turns on it may indicate that the parking brake is applied, that the brake fluid le...

  • Page 189

    The light will remain on until the cause is corrected. Note: the light may flash momentarily during sharp cornering maneuvers, which change fluid level condi- tions. The vehicle should have service performed, and the brake fluid level checked. If brake failure is indicated, immediate repair is neces...

  • Page 190

    Vehicle security warning light — if equipped red telltale light what it means vehicle security warning light — if equipped this light will flash at a fast rate for approximately 15 seconds when the vehicle security alarm is arming, and then will flash slowly until the vehicle is disarmed. Oil pressu...

  • Page 191

    Oil temperature warning light red telltale light what it means oil temperature warning light this telltale indicates engine oil temperature is high. If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible. Battery charge warning light red telltale light what...

  • Page 192

    Electronic throttle control (etc) warning light red telltale light what it means electronic throttle control (etc) warning light this light informs you of a problem with the electronic throttle control (etc) system. If a problem is detected while the engine is running, the light will either stay on ...

  • Page 193

    Engine temperature warning light red telltale light what it means engine temperature warning light this light warns of an overheated engine condition. If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound. If the temperature reaches the upper lim...

  • Page 194

    Electric power steering fail warning — if equipped red telltale light what it means electric power steering fail warning — if equipped this light is used to manage the electrical warning of the eps (power steering system). Re- fer to “power steering” in “starting and operating” for further informati...

  • Page 195

    Hood open warning light red telltale light what it means hood open warning light this indicator will illuminate when the hood is ajar/open and not fully closed. Liftgate open warning light red telltale light what it means liftgate open warning light this indicator will turn when the liftgate is open...

  • Page 196

    Transmission fault warning light red telltale light what it means transmission fault warning light this light will illuminate (together with a message in the evic and a buzzer) to indicate a transmission fault. Contact your authorized dealer if the message remains after restarting the engine. 194 ge...

  • Page 197

    Yellow telltale indicator lights anti-lock brake (abs) indicator light yellow telltale light what it means anti-lock brake (abs) indicator light after the ignition is turned on, the anti-lock brake system (abs) light illuminates to indi- cate function check at vehicle startup. If the light remains o...

  • Page 198

    Tire pressure monitoring indicator light yellow telltale light what it means tire pressure monitoring indicator light the warning light switches on and a message is displayed to indicate that the tire pressure is lower than the recommended value and/or that slow pressure loss is occurring. In these ...

  • Page 199

    On the vehicle placard or tire inflation pressure label, you should determine the proper tire inflation pressure for those tires. As an added safety feature, your vehicle has been equipped with a tire pressure monitoring system (tpms) that illuminates a low tire pressure telltale when one or more of...

  • Page 200

    Caution! The tpms has been optimized for the original equipment tires and wheels. Tpms pressures and warning have been established for the tire size equipped on your vehicle. Undesirable system opera- tion or sensor damage may result when using re- placement equipment that is not of the same size, (...

  • Page 201

    Electronic stability control (esc) indicator light — if equipped yellow telltale light what it means electronic stability control (esc) indicator light — if equipped the “esc indicator light” in the instrument cluster will come on when the ignition switch is turned to the on/run position, and when e...

  • Page 202

    Electronic stability control (esc) off indicator light — if equipped yellow telltale light what it means electronic stability control (esc) off indicator light — if equipped this light indicates the electronic stability control (esc) is off. 200 getting to know your instrument cluster.

  • Page 203

    Engine check/malfunction indicator light (mil) yellow telltale light what it means engine check/malfunction indicator light (mil) the engine check/malfunction indicator light (mil) is a part of an onboard diagnostic system called obd ii that monitors engine and automatic transmission control systems...

  • Page 204

    Caution! Prolonged driving with the malfunction indicator light (mil) on could cause damage to the engine control system. It also could affect fuel economy and driveability. If the mil is flashing, severe catalytic converter damage and power loss will soon occur. Immediate service is required. Warni...

  • Page 205

    Glow plug indicator light — if equipped yellow telltale light what it means glow plug indicator light to prevent possible engine damage while starting at low temperatures, this vehicle will in- hibit engine cranking and this icon will blink when the ambient temperature is less than -31° f (-35° c) a...

  • Page 206

    Low fuel indicator light yellow telltale light what it means low fuel indicator light when the fuel level reaches approximately 1.3–1.8 gal (5–7 l) this light will turn on, and re- main on until fuel is added. Lanesense indicator light — if equipped yellow telltale light what it means lanesense indi...

  • Page 207

    Vehicle security indicator light yellow telltale light what it means vehicle security indicator light this indicator will illuminate when the vehicle security alarm system has detected an at- tempt was made to break into the vehicle. Exterior bulb failure indicator light yellow telltale light what i...

  • Page 208

    Forward collision indicator light — if equipped yellow telltale light what it means forward collision indicator light this telltale will turn on warn you of a possible collision with the vehicle in front of you. Forward collision warning off indicator light — if equipped yellow telltale light what i...

  • Page 209

    Loose fuel filler cap indicator light — if equipped yellow telltale light what it means loose fuel filler cap indicator light — if equipped this light will illuminate when fuel filler cap is loose. Properly close the filler cap to disen- gage the light. If the light does not turn off, please see you...

  • Page 210

    Green telltale indicator lights turn signal indicator lights green tell- tale light what it means turn signal indicator lights the instrument cluster arrow will flash independently for the left or right turn signal as se- lected, as well as the exterior turn signal lamp(s) (front and rear) as select...

  • Page 211

    Front fog indicator light — if equipped green telltale light what it means front fog indicator light — if equipped this indicator will illuminate when the front fog lights are on. Cruise control engaged indicator light green telltale light what it means cruise control engaged indicator light this li...

  • Page 212

    Blue telltale indicator lights high beam indicator light blue telltale light what it means high beam indicator light this indicator shows that the high beam headlights are on. Push the multifunction control lever away from you to switch the headlights to high beam. Pull the lever toward you to switc...

  • Page 213

    White telltale indicator lights electronic speed control on indicator light white telltale light what it means electronic speed control on indicator light this light will turn on when the electronic speed control is on, but not set. Cruise control cancelled light white telltale light what it means c...

  • Page 214

    Onboard diagnostic system (obd ii) your vehicle is equipped with a sophisticated onboard diagnostic system called obd ii. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide ex...

  • Page 215

    Warning! • only an authorized service technician should con- nect equipment to the obd ii connection port in order to diagnose or service your vehicle. • if unauthorized equipment is connected to the obd ii connection port, such as a driver-behavior tracking device, it may: • be possible that vehicl...

  • Page 216

    Mapping and reconfigurable zone display (evic) — if equipped the display shows the following information, if equipped: • zone (1) – date (centered) – compass (centered) – time (centered) – external temp. (centered) • zone (2) – actual gear indication (centered) – prnd (centered) • zone (3) – date (c...

  • Page 217

    • zone (4) – audio info (centered) – title (centered) – title number (centered) • zone (4a) – title (centered) – browsing arrows (left) – title number (right) • zone (4b) – title (centered) • zone (4c) – title (centered) – browsing arrows (left) – title number (right) • zone (5) – trip and fuel labe...

  • Page 218

    Mapping and reconfigurable zone display (did) — if equipped • zone (1) – includes 1a and 1b combined – trip info (centered) – title (centered) – audio info (centered) • zone (1a) – up and down arrow (left) – title number • zone (1b) – external temp. (centered) – title (centered) – time (centered) • ...

  • Page 219

    • zone (2 & 3) – ignition button info (centered) • zone (4) – speed warning title • zone (5) – text (centered) – side distance warning – park sense: front & rear • zone (6) – odometer digits (left) – odometer unit (right) – side distance warning – park sense: front & rear • zone (7) – red telltales ...

  • Page 220

    • zone (15) – cruise control value (centered) • zone (16) – soft telltale (centered) – speed buzzer (right) • zone (17) – active park sense • zone (18) – active park sense oil change reset oil change due your vehicle is equipped with an engine oil change indicator system. The “oil change due” messag...

  • Page 221

    Note: if the indicator message illuminates when you start the vehicle, the oil change indicator system did not reset. If necessary, repeat this procedure. Evic/did control buttons the system allows the driver to select information by pushing the following buttons mounted on the steering wheel: evic/...

  • Page 222

    • up arrow button push and release the up arrow button to scroll upward through the main menu and submenus. • down arrow button push and release the down arrow button to scroll downward through the main menu and submenus. • right arrow button push and release the right arrow button to access the inf...

  • Page 223

    Menu items the menu has the following options: • speedometer • vehicle info • driver assist • fuel economy • trip • audio • messages • screen setup • settings speedometer push and release the up or down arrow button until “speedometer” is highlighted in the evic/did. Push the ok button to change the...

  • Page 224

    • oil temperature view the engine oil temperature. • battery voltage view the voltage value (state of charge) of the battery. • service view the service status message(s). Driver assist this menu item allows you to change the settings ( ⬙no- tice lanesense ⬙ and ⬙intensity lanesense⬙) relating to th...

  • Page 225

    Trip this menu item allows you to view information about the ⬙trip computer.⬙ the information displayed, for trip a and for trip b, are: • distance (miles or km) • average consumption (mpg, or l/ 100km or km/l) • travel time (hour/minute) audio this menu item allows you to view the instrument cluste...

  • Page 226

    The information that can be displayed is the connection status of the mobile phone (phone connected or discon- nected), the active telephone calls/incoming/on hold, and the management of double calls (first incoming second waiting, etc.). Messages this menu item allows you to display the information...

  • Page 227

    • ⴖfull prndⴖ (default): the right side of the display the letters prnd, the position assumed by the shift lever will be high- lighted in the display. During the operation in sequential mode ( ⬙autostick⬙), in place of the letter d, the gear will be will be displayed. In the upper-left/top right the...

  • Page 228

    Restore default settings selecting this item, and you can reset and restore the default settings. Settings this menu item allows you to change the settings for the following: • display • units • clock and date • security • safety and assistance • lights • doors and locks • compass (if equipped) vehi...

  • Page 229

    ⴖunits of measureⴖ by selecting the item ⬙units of measure,⬙ you can select the unit of measure to use for displaying various magni- tudes. Possible options are: • us • metric • custom ⴖclock & dataⴖ by selecting the item, ⬙clock & data⬙ you can adjust the clock. Possible options are: • set time: ad...

  • Page 230

    • seat belt reminder: this function is only viewable when the seat belt re- minder (sbr) system is active. • hill start assist: activation/deactivation of the hill start assist system. ⴖsafety & assistanceⴖ by selecting the item ⬙safety & assistance,⬙ you can make the following adjustments: • fcw: a...

  • Page 231

    • lanesense force: selection of the force to be applied to the steering wheel to put the car in the roadway through the system of electrical drive, in case of operation of the system lanesense • buzzer volume • maintenance brakes (if equipped): activation of the procedure to carry out braking system...

  • Page 232

    • sound horn with lock: activate/deactivate the horn when pressing the lock button on the rke. The options are ⬙off,⬙ ⬙first press,” and ⬙second press⬙ • horn with remote start: activate/deactivate the horn at the remote starting of the engine with the rke • unlock on first press of key fob (vehicle...

  • Page 233

    Variance compass variance is the difference between magnetic north and geographic north. To compensate for the differences, the variance should be set for the zone where the vehicle is driven, per the zone map. Once properly set, the compass will automatically compensate for the differences and prov...

  • Page 234

    Trip computer the trip computer is used to display information on car operation when the key is turned to the mar/run position. This function allows you to define two separate trips called “trip a” and “trip b” where the car’s ⬙complete trips ⬙ are monitored in an independent manner. Both trips can ...

  • Page 235

    Ok button short push of the button: display of various parameters. Long push of the button: reset quantities and begin a new trip. New trip starts after reset: • ⬙manual⬙ by pushing the ok button. • ⬙automatic⬙ when the ⬙distance⬙ reaches the value is 62140 (99999.9 km) or when the ⬙time travel⬙ rea...

  • Page 237

    Safety contents 䡵 brake system . . . . . . . . . . . . . . . . . . . . . . .237 䡵 electronic brake control system . . . .238 ▫ anti-lock brake system (abs) . . . . . . . . . . . .239 ▫ traction control system (tcs) . . . . . . . . . . . .241 ▫ brake assist system (bas) . . . . . . . . . . . . . . .2...

  • Page 238

    䡵 safety tips . . . . . . . . . . . . . . . . . . . . . . . . .309 ▫ transporting passengers . . . . . . . . . . . . . . . . .309 ▫ exhaust gas . . . . . . . . . . . . . . . . . . . . . . . . .310 ▫ safety checks you should make inside the vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Page 239

    Brake system your vehicle is equipped with dual hydraulic brake systems. If either of the two hydraulic systems loses normal capability, the remaining system will still func- tion. However, there will be some loss of overall braking effectiveness. This will be evident by increased pedal travel durin...

  • Page 240

    Electronic brake control system this system enhances directional control and stability of the vehicle under various driving conditions. Esc cor- rects for oversteering or understeering of the vehicle by applying the brake of the appropriate wheel to assist in counteracting the oversteer or understee...

  • Page 241

    Warning! (continued) accidents, including those resulting from excessive speed in turns, driving on very slippery surfaces, or hydroplaning. Esc also cannot prevent collisions resulting from loss of vehicle control due to inap- propriate driver input for the conditions. Only a safe, attentive, and s...

  • Page 242

    All vehicle wheels and tires must be the same size and type, and tires must be properly inflated, to produce accurate signals for the computer. Warning! Significant over or under-inflation of tires or mixing sizes of tires or wheels on the vehicle can lead to loss of braking effectiveness. The abs c...

  • Page 243

    Caution! The abs is subject to possible detrimental effects of electronic interference caused by improperly in- stalled aftermarket radios or telephones. Note: during severe braking conditions, a pulsing sen- sation may occur and a clicking noise will be heard. This is normal, indicating that the ab...

  • Page 244

    Pressure is applied to the slipping wheel(s) and engine power is reduced to provide enhanced acceleration and stability. A feature of the tcs system, brake limited differential (bld), functions similar to a limited slip differential and controls the wheel spin across a driven axle. If one wheel on a...

  • Page 245

    Warning! (continued) must never be exploited in a reckless or dangerous manner, which could jeopardize the user’s safety or the safety of others. Electronic roll mitigation (erm) this system anticipates the potential for wheel lift by monitoring the driver’s steering wheel input and the speed of the...

  • Page 246

    Warning! (continued) which could jeopardize the user’s safety or the safety of others. Hill start assist (hsa) the hsa system is designed to help the driver accelerate the vehicle from a complete stop while on an incline. If the driver releases the brake while stopped on an incline, hsa will continu...

  • Page 247

    Warning! (continued) responsibility to be attentive to distance to other vehicles, people, and objects, and most importantly brake operation to ensure safe operation of the ve- hicle under all road conditions. Your complete atten- tion is always required while driving to maintain safe control of you...

  • Page 248

    Hdc has three states: 1. Off (feature is not enabled and will not activate). 2. Enabled (feature is enabled and ready but activation conditions are not met, or driver is actively overriding with brake or throttle application). 3. Active (feature is enabled and actively controlling vehicle speed). En...

  • Page 249

    • vehicle is on a downhill grade of insufficient magni- tude (less than approximately 8%), is on level ground, or is on an uphill grade. • vehicle is shifted to park. Disabling hdc hdc will be deactivated and disabled if any of the following conditions occur: • the driver pushes the hdc switch. • th...

  • Page 250

    Warning! Hdc is only intended to assist the driver in control- ling vehicle speed when descending hills. The driver must remain attentive to the driving conditions and is responsible for maintaining a safe vehicle speed. Electronic stability control (esc) this system enhances directional control and...

  • Page 251

    Warning! • the electronic stability control (esc) cannot pre- vent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions. Esc cannot prevent all accidents, including those resulting from excessive speed in turns, driving on ve...

  • Page 252

    Esc operation modes to disable esc and other safety systems, follow the instruction below. There are three modes of active safety systems present on the vehicle: • esc on • partial off • full off esc on – two wheel drive vehicles and four wheel drive vehicles in 2wd and 4wd high range this is the no...

  • Page 253

    To enter the “partial off” mode, momentarily push the “esc off” button and the esc off indicator light will illuminate. To turn the esc on again, momentarily push the esc off button and the esc off indicator light will turn off. This will restore the normal “esc on” mode of operation. Note: to impro...

  • Page 254

    Warning! (continued) enhanced vehicle stability offered by the esc sys- tem is reduced. • trailer sway control (tsc) is disabled when the esc system is in the “partial off” mode. Full off – four-wheel drive vehicles in 4wd high and 4wd low range the “full off” mode is intended for off-highway and of...

  • Page 255

    Note: • “full off” is the only operating mode for esc in 4wd low range. The esc system will be in this mode whenever the vehicle is started in 4wd low range or the power transfer unit is shifted into 4wd low range. • the “esc off” message will display and a chime will sound when the gear selector is...

  • Page 256

    Running. If the “esc activation/malfunction indicator light” comes on continuously with the engine running, a malfunction has been detected in the esc system. If this light remains on after several ignition cycles, and the vehicle has been driven several miles/kilometers at speeds greater than 30 mp...

  • Page 257

    Trailer sway control (tsc) tsc uses sensors in the vehicle to recognize an exces- sively swaying trailer and will take the appropriate actions to attempt to stop the sway. The system may reduce engine power and apply the brake of the appro- priate wheel(s) to counteract the sway of the trailer. Tsc ...

  • Page 258

    Occupant restraint systems some of the most important safety features in your vehicle are the restraint systems: • seat belt systems • supplemental restraint systems (srs) air bags • child restraints important safety precautions please pay close attention to the information in this section. It tells...

  • Page 259

    6. All occupants should always wear their lap and shoulder belts properly. 7. The driver and front passenger seats should be moved back as far as practical to allow the advanced front air bags room to inflate. 8. Do not lean against the door or window. If your vehicle has side air bags, and deployme...

  • Page 260

    Ejection and the risk of injury caused by striking the inside of the vehicle. Everyone in a motor vehicle should be belted at all times. Enhanced seat belt use reminder system (beltalert) driver and passenger beltalert — if equipped beltalert is a feature intended to remind the driver and outboard f...

  • Page 261

    Sequence may repeat based on vehicle speed until the driver and occupied outboard front seat passenger seat belts are buckled. The driver should instruct all occu- pants to buckle their seat belts. Change of status if the driver or outboard front seat passenger (if equipped with outboard front passe...

  • Page 262

    Warning! • relying on the air bags alone could lead to more severe injuries in a collision. The air bags work with your seat belt to restrain you properly. In some collisions, the air bags won’t deploy at all. Always wear your seat belt even though you have air bags. • in a collision, you and your p...

  • Page 263

    Warning! (continued) • a lap belt worn too high can increase the risk of injury in a collision. The seat belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap part of your seat belt as low as possible and keep it snug. • a twisted seat belt may not pro...

  • Page 264

    Warning! (continued) • a frayed or torn seat belt could rip apart in a collision and leave you with no protection. Inspect the seat belt system periodically, checking for cuts, frays, or loose parts. Damaged parts must be re- placed immediately. Do not disassemble or modify the seat belt system. Sea...

  • Page 265

    3. When the seat belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” inserting latch plate into buckle inserting latch plate into buckle 6 safety 263.

  • Page 266

    4. Position the lap belt so that it is snug and lies low across your hips, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug seat belt reduces the risk of sliding...

  • Page 267

    3. Slide the latch plate upward over the folded webbing. The folded webbing must enter the slot at the top of the latch plate. 4. Continue to slide the latch plate up until it clears the folded webbing and the seat belt is no longer twisted. Adjustable upper shoulder belt anchorage in the driver and...

  • Page 268

    Note: the adjustable upper shoulder belt anchorage is equipped with an easy up feature. This feature allows the shoulder belt anchorage to be adjusted in the upward position without pushing or squeezing the release but- ton. To verify the shoulder belt anchorage is latched, pull downward on the shou...

  • Page 269

    4. When the seat belt is long enough to fit, insert the mini-latch plate into the mini-buckle until you hear a “click.” 5. Sit back in seat. Slide the regular latch plate up the webbing as far as necessary to allow the seat belt to go around your lap. 6. When the seat belt is long enough to fit, ins...

  • Page 270

    8. Position the shoulder belt on your chest so that it is comfortable and not resting on your neck. The retrac- tor will withdraw any slack in the seat belt. 9. To release the seat belt, push the red button on the buckle. 10. To disengage the mini-latch plate from the mini- buckle for storage, inser...

  • Page 271

    Seat belts and pregnant women seat belts must be worn by all occupants including pregnant women: the risk of injury in the event of an accident is reduced for the mother and the unborn child if they are wearing a seat belt. Position the lap belt snug and low below the abdomen and across the strong b...

  • Page 272

    The pretensioners are triggered by the occupant re- straint controller (orc). Like the air bags, the preten- sioners are single use items. A deployed pretensioner or a deployed air bag must be replaced immediately. Energy management feature this vehicle has a seat belt system with an energy manageme...

  • Page 273

    Around the occupant’s mid-section so as to not activate the alr. If the alr is activated, you will hear a clicking sound as the seat belt retracts. Allow the webbing to retract completely in this case and then carefully pull out only the amount of webbing necessary to comfortably wrap around the occ...

  • Page 274

    How to disengage the automatic locking mode unbuckle the combination lap/shoulder belt and allow it to retract completely to disengage the automatic locking mode and activate the vehicle sensitive (emergency) locking mode. Warning! • the seat belt assembly must be replaced if the switchable automati...

  • Page 275

    • supplemental side air bags • supplemental knee air bags • front and side impact sensors • seat belt pretensioners • seat belt buckle switch • seat track position sensors advanced front air bags this vehicle has advanced front air bags for both the driver and front passenger as a supplement to the ...

  • Page 276

    Warning! • being too close to the steering wheel or instrument panel during advanced front air bag deployment could cause serious injury, including death. Air bags need room to inflate. Sit back, comfortably extending your arms to reach the steering wheel or instrument panel. • never place a rear-fa...

  • Page 277

    Warning! • no objects should be placed over or near the air bag on the instrument panel or steering wheel because any such objects could cause harm if the vehicle is in a collision severe enough to cause the air bag to inflate. • do not put anything on or around the air bag covers or attempt to open...

  • Page 278

    Because air bag sensors measure vehicle deceleration over time, vehicle speed and damage by themselves are not good indicators of whether or not an air bag should have deployed. Seat belts are necessary for your protection in all colli- sions, and also are needed to help keep you in position, away f...

  • Page 279

    Provides enhanced protection during a frontal impact by working together with the seat belts, pretensioners, and advanced front air bags. Supplemental side air bags your vehicle is equipped with two types of side air bags: 1. Supplemental seat-mounted side air bags (sabs): located in the outboard si...

  • Page 280

    Deploys through the seat seam into the space between the occupant and the door. The sab moves at a very high speed and with such a high force that it could injure occupants if they are not seated properly, or if items are positioned in the area where the sab inflates. Children are at an even greater...

  • Page 281

    The sabics deploy downward, covering the side win- dows. An inflating sabic pushes the outside edge of the trim out of the way and covers the window. The sabics inflate with enough force to injure occupants if they are not belted and seated properly, or if items are positioned in the area where the ...

  • Page 282

    The sabics and sabs (“side air bags”) are designed to activate in certain side impacts and certain rollover events. The occupant restraint controller (“orc”) de- termines whether the deployment of the side air bags in a particular side impact or rollover event is appropriate, based on the severity a...

  • Page 283

    Warning! (continued) properly. In some collisions, side air bags won’t deploy at all. Always wear your seat belt even though you have side air bags. Note: air bag covers may not be obvious in the interior trim, but they will open during air bag deployment. Side impacts in side impacts, the side impa...

  • Page 284

    Air bags is appropriate, the rollover sensing system will also deploy the seat belt pretensioners on both sides of the vehicle. If a deployment occurs the advanced front air bags are designed to deflate immediately after deployment. Note: front and/or side air bags will not deploy in all collisions....

  • Page 285

    Warning! Deployed air bags and seat belt pretensioners cannot protect you in another collision. Have the air bags, seat belt pretensioners, and the seat belt retractor assemblies replaced by an authorized dealer imme- diately. Also, have the occupant restraint controller system serviced as well. Not...

  • Page 286

    Enhanced accident response system reset procedure after the event occurs, when the system is active, a message regarding fuel cutoff is displayed. Turn the ignition switch from ignition avv/start or mar/ acc/on/run to ignition stop/off/lock. Care- fully check the vehicle for fuel leaks in the engine...

  • Page 287

    Customer action customer will see 6. Turn left turn signal switch on. Left turn light is on solid. Right turn light is on solid. 7. Turn left turn signal switch off. (turn signal switch must be placed in neutral state). Left turn light is off. Right turn light is off. 8. Turn ignition off. 9. Turn h...

  • Page 288

    The mar/acc/on/run position. After the self-check, the air bag warning light will turn off. If the orc detects a malfunction in any part of the system, it turns on the air bag warning light, either momentarily or continuously. A single chime will sound to alert you if the light comes on again after ...

  • Page 289

    Redundant air bag warning light if a fault with the air bag warning light is detected, which could affect the supplemental restraint system (“srs”), the redundant air bag warning light will illuminate on the in- strument panel. The redundant air bag warning light will stay on until the fault is clea...

  • Page 290

    Warning! (continued) not function properly if modifications are made. Take your vehicle to an authorized dealer for any air bag system service. If your seat, including your trim cover and cushion, needs to be serviced in any way (including removal or loosening/tightening of seat attachment bolts), t...

  • Page 291

    Note: edr data are recorded by your vehicle only if a non-trivial crash situation occurs; no data are recorded by the edr under normal driving conditions and no per- sonal data (e.G., name, gender, age, and crash location) are recorded. However, other parties, such as law en- forcement, could combin...

  • Page 292

    There are different sizes and types of restraints for children from newborn size to the child almost large enough for an adult safety belt. Always check the child seat owner’s manual to make sure you have the correct seat for your child. Carefully read and follow all the instructions and warnings in...

  • Page 293

    Summary of recommendations for restraining children in vehicles child size, height, weight or age recommended type of child restraint infants and toddlers children who are two years old or younger and who have not reached the height or weight limits of their child re- straint either an infant carrie...

  • Page 294

    Infants and child restraints safety experts recommend that children ride rear-facing in the vehicle until they are two years old or until they reach either the height or weight limit of their rear-facing child restraint. Two types of child restraints can be used rear-facing: infant carriers and conv...

  • Page 295

    Remain in a forward-facing child seat with a harness for as long as possible, up to the highest weight or height allowed by the child seat. All children whose weight or height is above the forward-facing limit for the child seat should use a belt-positioning booster seat until the vehicle’s seat bel...

  • Page 296

    Children too large for booster seats children who are large enough to wear the shoulder belt comfortably, and whose legs are long enough to bend over the front of the seat when their back is against the seatback, should use the seat belt in a rear seat. Use this simple 5-step test to decide whether ...

  • Page 297

    Recommendations for attaching child restraints restraint type combined weight of the child + child restraint use any attachment method shown with an “x” below latch – lower anchors only seat belt only latch – lower anchors + top tether anchor seat belt + top tether anchor rear-facing child restraint...

  • Page 298

    Lower anchors and tethers for children (latch) restraint system your vehicle is equipped with the child restraint anchor- age system called latch, which stands for lower anchors and tethers for children. The latch system has three vehicle anchor points for installing latch- equipped child seats. The...

  • Page 299

    Latch positions for installing child restraints in this vehicle • — lower anchorage symbol 2 anchorages per seating position • — top tether anchorage symbol 6 safety 297.

  • Page 300

    Frequently asked questions about installing child restraints with latch what is the weight limit (child’s weight + weight of the child restraint) for using the latch anchorage system to attach the child restraint? 65 lbs (29.5 kg) use the latch anchorage system until the combined weight of the child...

  • Page 301

    Frequently asked questions about installing child restraints with latch can two child restraints be attached us- ing a common lower latch anchorage? No never “share” a latch anchorage with two or more child restraints. If the center position does not have dedicated latch lower anchorages, use the se...

  • Page 302

    Locating latch anchorages the lower anchorages are round bars that are found at the rear of the seat cushion where it meets the seatback, below the anchorage sym- bols on the seatback. They are just visible when you lean into the rear seat to install the child restraint. You will easily feel them if...

  • Page 303

    Locating tether anchorages there are tether strap anchorages behind each rear seating position located on the back of the seat. Latch-compatible child restraint systems will be equipped with a rigid bar or a flexible strap on each side. Each will have a hook or connector to attach to the lower ancho...

  • Page 304

    Warning! (continued) • never use the same lower anchorage to attach more than one child restraint. Please refer to “installing the latch-compatible child restraint system” in this “child restraints” section for typical instal- lation instructions. Always follow the directions of the child restraint ...

  • Page 305

    4. If the child restraint has a tether strap, connect it to the top tether anchorage. See the section “installing child restraints using the top tether anchorage” for direc- tions to attach a tether anchor. 5. Tighten all of the straps as you push the child restraint rearward and downward into the s...

  • Page 306

    Warning! (continued) • child restraint anchorages are designed to with- stand only those loads imposed by correctly-fitted child restraints. Under no circumstances are they to be used for adult seat belts, harnesses, or for attaching other items or equipment to the vehicle. Installing child restrain...

  • Page 307

    Frequently asked questions about installing child restraints with seat belts what is the weight limit (child’s weight + weight of the child restraint) for using the tether anchor with the seat belt to attach a forward facing child restraint? Weight limit of the child restraint always use the tether ...

  • Page 308

    Installing a child restraint with a switchable automatic locking retractor (alr) 1. Place the child seat in the center of the seating position. For some second row seats, you may need to recline the seat and/or raise the head restraint to get a better fit. If the rear seat can be moved forward and r...

  • Page 309

    Strap. See the section “installing child restraints using the top tether anchorage” for directions to attach a tether anchor. 9. Test that the child restraint is installed tightly by pulling back and forth on the child seat at the belt path. It should not move more than 1 inch (25.4 mm) in any direc...

  • Page 310

    Tether anchorage for that seating position, move the child restraint to another position in the vehicle if one is available. 2. Route the tether strap to provide the most direct path for the strap between the anchor and the child seat. If your vehicle is equipped with adjustable rear head restraints...

  • Page 311

    Warning! • an incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchorage position directly behind the child seat to secure a child restraint top tether strap. • if your vehicle is equipped with a split rear seat, make sure the tethe...

  • Page 312

    Exhaust gas warning! Exhaust gases can injure or kill. They contain carbon monoxide (co), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing (co), follow these safety tips: • do not run the engine in a closed garage or in confined...

  • Page 313

    Safety checks you should make inside the vehicle seat belts inspect the seat belt system periodically, checking for cuts, frays, and loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Front seat belt assemblies must be replaced after a collision. Rear s...

  • Page 314

    Cannot slip out of position and interfere with the pedals or impair safe operation of your vehicle in other ways. Warning! Pedals that cannot move freely can cause loss of vehicle control and increase the risk of serious per- sonal injury. • always make sure that floor mats are properly attached to ...

  • Page 315

    Periodic safety checks you should make outside the vehicle tires examine tires for excessive tread wear and uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread or sidewall. Inspect the tread for cuts and cracks. Inspect sidewalls for cuts, cracks, and bulges. C...

  • Page 317

    Starting and operating contents 䡵 starting the engine . . . . . . . . . . . . . . . .319 ▫ tip start feature . . . . . . . . . . . . . . . . . . . . . .320 ▫ if engine fails to start . . . . . . . . . . . . . . . . .320 ▫ cold weather operation . . . . . . . . . . . . . . . .321 ▫ extended park star...

  • Page 318

    ▫ key ignition park interlock. . . . . . . . . . . . . . .347 ▫ brake/transmission shift interlock system. . . .348 䡵 speed control — if equipped . . . . . . . . .348 ▫ activation. . . . . . . . . . . . . . . . . . . . . . . . . . .349 ▫ setting a desired speed . . . . . . . . . . . . . . . . .349 ▫...

  • Page 319

    ▫ lanesense warning message. . . . . . . . . . . . . .368 ▫ changing lanesense status . . . . . . . . . . . . . .376 䡵 rear parksense — if equipped . . . . . . . .377 ▫ rear parksense sensors . . . . . . . . . . . . . . . . .377 ▫ enabling and disabling rear parksense . . . . .379 ▫ service the rear...

  • Page 320

    䡵 off-road driving tips . . . . . . . . . . . . . . . .407 ▫ when to use 4wd low range . . . . . . . . . . .407 ▫ driving through water . . . . . . . . . . . . . . . . .407 ▫ driving in snow, mud and sand . . . . . . . . . .408 ▫ hill climbing . . . . . . . . . . . . . . . . . . . . . . . .409 ▫ tra...

  • Page 321

    Starting the engine before starting your vehicle, adjust your seat, adjust the inside and outside mirrors, fasten your seat belt, and if present, instruct all other occupants to buckle their seat belts. Warning! • never leave children alone in a vehicle, or with access to an unlocked vehicle. • allo...

  • Page 322

    4. If the engine does not start, place the ignition in the stop/off position and wait 10-15 seconds before attempting to restart the engine. Automatic transmission proceed as follows: 1. Set the electric park brake (epb) and put the gear selector in the park or neutral position. 2. Press on the brak...

  • Page 323

    Floor and hold it there. Crank the engine for no more than 15 seconds. This should clear any excess fuel in case the engine is flooded. Leave the ignition key in the mar/ run position, release the accelerator pedal and repeat the “normal starting” procedure. Caution! To prevent damage to the starter...

  • Page 324

    Turbo engine below -20°f (-29°c) and for the 2.4l engine below -29°f (-34°c) and is recommended for the 2.4l engine below -20°f (-29°c). To prevent possible engine damage while starting at low temperatures, this vehicle will inhibit engine cranking when the ambient temperature is less than -34°f (-3...

  • Page 325

    After starting — warming up the engine proceed as follows: • travel slowly, letting the engine run at a reduced rpm, without accelerating suddenly. • it is recommended to wait until the engine coolant temperature gauge starts to rise for maximum perfor- mance. Stopping the engine vehicles equipped w...

  • Page 326

    When the ignition is in the stop/off position, the window switches remains active for three minutes. Opening a front door will cancel this function. After severe driving, idle the engine to allow the tem- perature inside the engine compartment to cool before shutting off the engine. Turbocharger “co...

  • Page 327

    Note: a new engine may consume some oil during its first few thousand miles (kilometers) of operation. This should be considered a normal part of the break-in and not interpreted as a problem. Electric park brake (epb) your vehicle is equipped with an electric park brake system (epb) that offers sim...

  • Page 328

    Parking brake is fully engaged, the brake warning lamp in the instrument cluster and an indicator on the switch will illuminate. If your foot is on the brake pedal while you apply the epb, you may notice a small amount of brake pedal movement. The epb can be applied even when the ignition switch is ...

  • Page 329

    Note: • when parking on a hill, it is important to turn the front wheels toward the curb on a downhill grade and away from the curb on an uphill grade. Apply the epb before placing the gear selector in park, otherwise the load on the transmission locking mechanism may make it difficult to move the g...

  • Page 330

    Warning! (continued) keyless enter-n-go in the acc or on/run mode. A child could operate power windows, other con- trols, or move the vehicle. • be sure the parking brake is fully disengaged before driving; failure to do so can lead to brake failure and a collision. • always fully apply the parking ...

  • Page 331

    Warning! Driving the vehicle with the parking brake engaged, or repeated use of the parking brake to slow the vehicle may cause serious damage to the brake sys- tem. Be sure the parking brake is fully disengaged before driving; failure to do so can lead to brake failure and a collision. In the unlik...

  • Page 332

    • there is no attempt to depress the brake pedal or accelerator pedal. • the seat belt is unbuckled. • the driver door is open. • the vehicle is not in the park position. For manual transmissions, the epb will automatically engage if all of the following conditions are met: • vehicle speed is below ...

  • Page 333

    Your vehicle. This menu based system will guide you through the steps necessary to retract the epb actuator in order to perform rear brake service. Service mode has requirements that must be met in order to be activated: • the vehicle must be at a standstill. • the parking brake must be disabled. • ...

  • Page 334

    Manual transmission warning! You or others could be injured if you leave the vehicle unattended without having the parking brake fully applied. The parking brake should al- ways be applied when the driver is not in the vehicle, especially on an incline. Caution! Never drive with your foot resting on...

  • Page 335

    To engage reverse gear from the neutral position, lift the reverse ring, located below the knob and simultaneously move the lever to the left and then forward. Shifting fully press the clutch pedal before shifting gears. As you release the clutch pedal, lightly press the accelerator pedal. You shoul...

  • Page 336

    Downshifting moving from a high gear down to a lower gear is recommended to preserve brakes when driving down steep hills. In addition, downshifting at the right time provides better acceleration when you desire to resume speed. Downshift progressively. Do not skip gears to avoid overspeeding the en...

  • Page 337

    Caution! (continued) • failure to follow the maximum recommended downshifting speeds may cause the engine damage and/or damage the clutch, even if the clutch pedal is pressed. • descending a hill in low range with clutch pedal depressed could result in clutch damage. Maximum recommended downshift sp...

  • Page 338

    Caution! If you skip a gear while downshifting or downshift at too high of a vehicle speed, these conditions may cause the engine to overspeed if too low of a gear is selected and the clutch pedal is released. Damage to the clutch and the transmission can result from skipping a gear while downshifti...

  • Page 339

    Warning! (continued) your foot is not firmly pressing the brake pedal, the vehicle could accelerate quickly forward or in re- verse. You could lose control of the vehicle and hit someone or something. Only shift into gear when the engine is idling normally and your foot is firmly pressing the brake ...

  • Page 340

    Caution! Damage to the transmission may occur if the follow- ing precautions are not observed: • shift into or out of park or reverse only after the vehicle has come to a complete stop. • do not shift between park, reverse, neu- tral, or drive when the engine is above idle speed. • before shifting i...

  • Page 341

    Note: if the gear selector cannot be moved to the park, reverse, or neutral position (when pushed for- ward) it is probably in the autostick (+/-) position (beside the drive position). In autostick mode, the transmission gear (1, 2, 3, etc.) is displayed in the instrument cluster. Move the gear sele...

  • Page 342

    The nine-speed transmission has been developed to meet the needs of fca current and future lineup of fwd/ awd vehicles. Software and calibration is refined to optimize the customer’s driving experience and fuel economy. By design, some vehicle and drive-line combi- nations utilize 9th gear only in v...

  • Page 343

    Warning! • never use the park position as a substitute for the electric parking brake (epb). Always apply the epb fully when parked to guard against vehicle movement and possible injury or damage. • your vehicle could move and injure you and others if it is not completely in park. Check by trying to...

  • Page 344

    Warning! (continued) seriously or fatally injured. Children should be warned not to touch the parking brake, brake pedal or the gear selector. • do not leave the key fob in or near the vehicle (or in a location accessible to children), and do not leave the ignition (of a vehicle equipped with keyles...

  • Page 345

    Reverse (r) this range is for moving the vehicle backward. Shift into reverse only after the vehicle has come to a complete stop. Neutral (n) use this range when the vehicle is standing for prolonged periods with the engine running. The engine may be started in this range. Apply the electric park br...

  • Page 346

    While towing a heavy trailer), use the autostick shift control (refer to “autostick” in this section for further information) to select a lower gear. Under these condi- tions, using a lower gear will improve performance and extend transmission life by reducing excessive shifting and heat buildup. If...

  • Page 347

    Operation when the gear selector is in the autostick position (beside the drive position), it can be moved forward and rearward. This allows the driver to manually select the transmission gear being used. Moving the gear selector forward (-) triggers a downshift, and rearward (+) an upshift. The cur...

  • Page 348

    • the system may revert to automatic shift mode if a fault or overheat condition is detected. To disengage autostick mode, return the gear selector to the drive position. You can shift in or out of the autostick position at any time without taking your foot off the accelerator pedal. Warning! Do not...

  • Page 349

    6. Shift into the desired gear range. If the problem is no longer detected, the transmission will return to normal operation. Note: even if the transmission can be reset, we recom- mend that you visit your authorized dealer at your earliest possible convenience. Your authorized dealer has diagnostic...

  • Page 350

    Brake/transmission shift interlock system this vehicle is equipped with a brake transmission shift interlock system (btsi) that holds the gear selector in park unless the brakes are applied. To shift the trans- mission out of park, the ignition switch must be turned to the mar/run position (engine r...

  • Page 351

    Note: • in order to ensure proper operation, the electronic speed control system has been designed to shut down if multiple speed control functions are operated at the same time. If this occurs, the electronic speed control system can be reactivated by pushing the electronic speed control on/off but...

  • Page 352

    When the vehicle has reached the desired speed, push the set (+) or set (-) button and release. Release the accelerator and the vehicle will operate at the selected speed. Deactivation a soft tap on the brake pedal, pushing the cancel button, or normal brake pressure while slowing the vehicle will d...

  • Page 353

    Metric speed (km/h) • pushing the set + button once will result in a 1 km/h increase in set speed. Each subsequent tap of the button results in an increase of 1 km/h. • if the button is continually pushed, the set speed will continue to increase until the button is released, then the new set speed w...

  • Page 354

    Accelerating for passing push the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed. Four wheel drive — jeep active drive (4wd) and jeep active drive low (4wd low) your vehicle may be equipped with a power transfer unit (ptu). This system is auto...

  • Page 355

    Enabling four wheel drive (4x4) the buttons for the activation of four wheel drive are located on the device selec-terrain and allow you to select the following: • 4wd lock • 4wd low — (trailhawk models only) active drive control — if equipped the power transfer unit (ptu) is locked to ensure immedi...

  • Page 356

    The other driving mode. 4wd lock can be enabled by the following ways: • when the 4wd lock button is pushed. • when the selec-terrain switch is rotated from auto to any other off-road modes. Active drive with low control — (trailhawk models only) selec-terrain switch (trailhawk) 354 starting and ope...

  • Page 357

    The 4wd low mode helps to improve the off-road performance in all modes. To enable 4wd low, please follow the steps below: enabling 4wd low with the vehicle stationary, the ignition in the mar/ run or with the engine running, shift the transmission into neutral and push the button once 4wd low. The ...

  • Page 358

    • auto: this four-wheel drive operation is a continu- ous operation, is fully automatic and can be used on and off road. This mode balances traction to ensure maneuverability and acceleration improvement com- pared to a vehicle with two wheel drive. This mode selec-terrain switch selec-terrain switc...

  • Page 359

    Also reduces fuel consumption, since it allows the disconnect of the drive shaft where conditions permit. • snow: this mode allows you to have greater stability under conditions of bad weather. For use on and off road on surfaces with poor traction, such as roads covered with snow. When in snow mode...

  • Page 360

    Forward collision warning (fcw) with mitigation — if equipped forward collision warning (fcw) with mitigation operation — if equipped the forward collision warning (fcw) system with mitigation provides the driver with audible warnings, visual warnings (within the evic/did), and may apply a brake jer...

  • Page 361

    Vehicles with a manual transmission : after the end of the intervention of automatic braking, the engine could stall, unless the driver can depress the clutch pedal. Vehicles with automatic transmission : after the end of the intervention of automatic braking, the transmission may remain in last gea...

  • Page 362

    Note: • the minimum speed for fcw activation is 4 mph (7 km/h). • the maximum speed for fcw activation is 124 mph (200 km/h). • the fcw alerts may be triggered on objects other than vehicles such as guard rails or sign posts based on the course prediction. This is expected and is a part of normal fc...

  • Page 363

    Turning fcw on or off the forward collision menu setting is located in the uconnect settings. Note: the default status of fcw is “warning + active braking,” this allows the system to warn you of a possible collision with the vehicle in front of you and enable the active braking. • changing the fcw s...

  • Page 364

    Limited and gradual. This setting gives the driver the maximum possible time of reaction to prevent a possible accident. By changing the option to ⬙near⬙, the system will warn the driver of a possible accident with the vehicle ahead of it when the latter is a reduced distance. This setting offers a ...

  • Page 365

    Evic/did will display “fcw front radar sensor tem- porarily blocked” and the system will deactivate. The “fcw front radar sensor temporarily blocked” message can sometimes be displayed while driving in highly reflective areas (i.E. Tunnels with reflective tiles, or ice and snow). The system will rec...

  • Page 366

    The intervention of the system could be unexpected or delayed. The driver must therefore always pay particular attention, while maintaining control of the car to drive in complete safety. Driving in the vicinity of a curve entering or exiting a large curve, the system could detect the presence of a ...

  • Page 367

    Action of the radar sensor and could therefore not react in the presence of small vehicles such as bicycles or motor- cycles. Lane changing of other vehicles vehicles that suddenly change lane, while standing in the traffic lane of their car and inside the field of action of the radar sensor may cau...

  • Page 368

    Passing of vehicles in an oncoming intersection the system could temporarily react to a vehicle that crossed the range of the radar sensor, in an oncoming intersection. General information this vehicle has systems that operate on radio frequency that comply with part 15 of the federal communications...

  • Page 369

    Lanesense — if equipped lanesense operation the lanesense system is operational at speeds above 37 mph (60 km/h) and below 112 mph (180 km/h). The lanesense system uses a forward looking camera to detect lane markings and measure vehicle position within the lane boundaries. When both lane markings a...

  • Page 370

    The lanesense button is located on the switch panel below the uconnect display. To turn the lanesense system on, push the lanesense button (led turns on). A “lane sense on” message is shown in the evic/did. To turn the lanesense system off, push the lanesense button once (led turns off). Note: the l...

  • Page 371

    Left lane departure — only left lane detected • when the lanesense system is on, the lanesense indicator is solid white when only the left lane mark- ing has been detected and the system is ready to provide visual warnings in the evic if an uninten- tional lane departure occurs. • when the lanesense...

  • Page 372

    Left lane departure — both lanes detected • when the lanesense system is on, the lane lines turn from gray to white to indicate that both of the lane markings have been detected. The lanesense indicator is solid green when both lane markings have been detected and the system is “armed” to provide vi...

  • Page 373

    • for example: if approaching the left side of the lane, the steering wheel will turn to the right. • when the lanesense system senses the lane has been approached and is in a lane departure situation, the left thick lane line flashes from white to gray, the left thin line remains solid white and th...

  • Page 374

    Note: the lanesense system operates with the similar behavior for a right lane departure. 7.0 did screen — if equipped when the lanesense system is on, the lane lines are gray when both of the lane boundaries have not been detected and the lanesense indicator is solid white. Lane approached (flashin...

  • Page 375

    Left lane departure — only left lane detected • when the lanesense system is on, the lanesense indicator is solid white when only the left lane mark- ing has been detected and the system is ready to provide visual warnings in the did if an unintentional lane departure occurs. • when the lanesense sy...

  • Page 376

    Left lane departure — both lanes detected • when the lanesense system is on, the lane lines turn from gray to white to indicate that both of the lane markings have been detected. The lanesense indicator is solid green when both lane markings have been detected and the system is “armed” to provide vi...

  • Page 377

    • for example: if approaching the left side of the lane the steering wheel will turn to the right. • when the lanesense system senses the lane has been approached and is in a lane departure situation, the left thick lane line flashes yellow (on/off) and the left thin line remains solid yellow. The l...

  • Page 378

    Note: the lanesense system operates with the similar behavior for a right lane departure. Changing lanesense status the lanesense system has settings to adjust the intensity of the torque warning and the warning zone sensitivity (early/late) that you can configure through the uconnect system screen....

  • Page 379

    Rear parksense — if equipped the rear parksense system provides visual and audible indications of the distance between the rear fascia and a detected obstacle when backing up, e.G. During a parking maneuver. Refer to parksense system usage precautions for limitations of this system and recommendatio...

  • Page 380

    Chime by shifting the vehicle in reverse and in the case of the presence of a rear obstacle, an acoustic signal that varies with the distance of the obstacle from the bumper is activated. The frequency of the acoustic signal: • increases with the distance between car and object decreases. • becomes ...

  • Page 381

    If an obstacle is detected in the left and/or right rear region, the display will show a single flashing arc in the left and/or right rear region and will produce a fast sound tone. As the vehicle moves closer to the obstacle, the display will show the single arc moving closer to the vehicle and the...

  • Page 382

    Caution! After turning off the ignition, the rear parksense remains in this setting until the next key cycle, even in the case of changing the setting of starting mar/ run to stop/off and then again in mar/run. Service the rear parksense system during vehicle start up, when the rear parksense system...

  • Page 383

    Parksense system usage precautions note: • ensure that the outer surface and the underside of the rear bumper is clean and clear of snow, ice, mud, dirt or other obstruction to keep the rear parksense system operating properly. • jackhammers, large trucks, and other vibrations could affect the perfo...

  • Page 384

    Warning! • drivers must be careful when backing up even when using parksense. Always check carefully behind your vehicle, look behind you, and be sure to check for pedestrians, animals, other vehicles, obstructions, and blind spots before backing up. You are responsible for safety and must continue ...

  • Page 385

    When the vehicle is shifted out of reverse (with camera delay turned off), the rear camera mode is exited and the navigation or audio screen appears again. When the vehicle is shifted out of reverse (with camera delay turned on), the camera image will continue to be displayed for up to 10 seconds af...

  • Page 386

    The following table shows the approximate distances for each zone: zone distance to the rear of the vehicle red 0 - 1 ft (0 - 30 cm) yellow 1 ft - 3 ft (30 cm - 1 m) green 3 ft or greater (1 m or greater) note: if snow, ice, mud, or any foreign substance builds up on the camera lens, clean the lens,...

  • Page 387

    Caution! • to avoid vehicle damage, rear back up camera should only be used as a parking aid. The rear back up camera is unable to view every obstacle or object in your drive path. • to avoid vehicle damage, the vehicle must be driven slowly when using the rear back up cam- era to be able to stop in...

  • Page 388

    The tpms will continue to warn the driver of low tire pressure as long as the condition exists, and will not turn off until the tire pressure is at or above the recommended cold placard pressure. Once the low tire pressure warn- ing (tire pressure monitoring telltale light) illuminates, you must inc...

  • Page 389

    Caution! • the tpms has been optimized for the original equipment tires and wheels. Tpms pressures and warning have been established for the tire size equipped on your vehicle. Undesirable system op- eration or sensor damage may result when using replacement equipment that is not of the same size, t...

  • Page 390

    Correct tire pressure using an accurate tire pressure gauge, even if underinflation has not reached the level to trigger illumination of the “tire pressure monitor- ing telltale light”. • seasonal temperature changes will affect tire pressure, and the tpms will monitor the actual tire pressure in th...

  • Page 391

    System receives the updated tire pressures, the system will automatically update and the “tire pressure moni- toring telltale light” will turn off. Note: when filling warm tires, the tire pressure may need to be increased up to an additional 4 psi (30 kpa) above the recommended cold placard pressure...

  • Page 392

    Vehicles with compact spare or non-matching full size spare 1. The compact spare tire or non-matching full size spare tire does not have a tire pressure monitoring sensor. Therefore, the tpms will not monitor the pressure in the spare tire. 2. If you install the compact or non-matching full size spa...

  • Page 393

    Note: it is particularly important for you to check the tire pressure in all of the tires on your vehicle monthly and to maintain the proper pressure. The tpms consists of the following components: • receiver module • four tire pressure monitoring sensors • various tire pressure monitoring system me...

  • Page 394

    Should this occur, you should stop as soon as possible and inflate the tires with low pressure (those in a different color in the evic/did graphic) to the vehicle’s recommended cold placard pressure value as shown in the ⬙inflate to xx⬙ message. Once the system receives the updated tire pressures, t...

  • Page 395

    1. Jamming due to electronic devices or driving next to facilities emitting the same radio frequencies as the tpms sensors. 2. Installing some form of aftermarket window tinting that affects radio wave signals. 3. Lots of snow or ice around the wheels or wheel housings. 4. Using tire chains on the v...

  • Page 396

    Vehicles with compact spare or non-matching full size spare 1. The compact spare tire or non-matching full size does not have a tire pressure monitoring sensor. Therefore, the tpms will not monitor the pressure in the compact spare tire. 2. If you install the compact or non-matching full size spare ...

  • Page 397

    Vehicle may need to be driven for up to 20 minutes above 15.5 mph (25 km/h) in order for the tpms to receive this information. General information this device complies with part 15 of the fcc rules and rss-210 of industry canada. Operation is subject to the following two conditions: (1) this device ...

  • Page 398

    Poor quality gasoline can cause problems such as hard starting, stalling, and hesitations. If you experience these symptoms, try another brand of gasoline before consid- ering service for the vehicle. 2.4l engine all available gasoline engines are designed to meet all emissions regulations and pro- ...

  • Page 399

    Gasoline/oxygenate blends some fuel suppliers blend unleaded gasoline with oxy- genates such as ethanol. Caution! Do not use gasoline containing methanol or gaso- line containing more than 15% ethanol (e-15). Use of these blends may result in starting and drivability problems, damage critical fuel s...

  • Page 400

    If a non-ffv vehicle is inadvertently fueled with e-85 fuel, the engine will have some or all of these symptoms: • operate in a lean mode. • obd ii “malfunction indicator light” on. • poor engine performance. • poor cold start and cold drivability. • increased risk for fuel system component corrosio...

  • Page 401

    Indiscriminate use of fuel system cleaning agents should be avoided. Many of these materials intended for gum and varnish removal may contain active solvents or similar ingredients. These can harm fuel system gasket and diaphragm materials. Fuel system cautions caution! Follow these guidelines to ma...

  • Page 402

    Carbon monoxide warnings warning! Carbon monoxide (co) in exhaust gases is deadly. Follow the precautions below to prevent carbon monoxide poisoning: • do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas, which can kill. Never run the engine in a closed area, such...

  • Page 403

    Opening the door for filling proceed as follows: • open the door, by pushing and releasing on the indentation point indicated by the arrow. • insert the fuel nozzle in the filler pipe and proceed with filling the fuel tank. • before removing the nozzle, wait at least 10 seconds to allow the fuel to ...

  • Page 404

    Emergency refueling procedure if the vehicle is out of fuel proceed as follows: • open the liftgate and remove the emergency fuel fill funnel located in the cargo area. • open the fuel door. • insert the emergency fuel fill funnel in the filler pipe and proceed to fill the fuel tank. Emergency fuel ...

  • Page 405

    • remove the emergency fuel fill funnel, and close the door. • store the emergency fuel fill funnel in the cargo area. Warning! • do not to affix objects/plugs to the end of the filler neck other than is provided on the car. • the use of objects/plugs do not comply with the vehicle and may cause pre...

  • Page 406

    Vehicle loading certification label as required by national highway traffic safety admin- istration regulations, your vehicle has a certification label affixed to the driver’s side door or pillar. This label contains the month and year of manufacture, gross vehicle weight rating (gvwr), gross axle w...

  • Page 407

    Tire size the tire size on the vehicle certification label represents the actual tire size on your vehicle. Replacement tires must be equal to the load capacity of this tire size. Rim size this is the rim size that is appropriate for the tire size listed. Inflation pressure this is the cold tire inf...

  • Page 408

    Items down low and be sure that the weight is distributed equally. Stow all loose items securely before driving. Improper weight distributions can have an adverse effect on the way your vehicle steers and handles and the way the brakes operate. Caution! Do not load your vehicle any heavier than the ...

  • Page 409

    Off-road driving tips when to use 4wd low range when off-road driving, shift to 4wd low for additional traction and control on slippery or difficult terrain, ascending or descending steep hills, and to increase low-speed pulling power (refer to “all wheel drive and four-wheel drive operation” in thi...

  • Page 410

    Entering. Proceed with caution and maintain a steady controlled speed less than 5 mph (8 km/h) in deep water to minimize wave effects. Flowing water if the water is swift flowing and rising (as in storm run-off) avoid crossing until the water level recedes and/or the flow rate is reduced. If you mus...

  • Page 411

    Avoid abrupt downshifts on icy or slippery roads be- cause engine braking may cause skidding and loss of control. Hill climbing note: before attempting to climb a hill, determine the conditions at the crest and/or on the other side. Before climbing a steep hill, shift the transmission to a lower gea...

  • Page 412

    Traction downhill shift the transmission into a low gear and the 4wd system to 4wd low range or select hill descent control if equipped (refer to ⬙electronic brake control system ⬙ in this section for further information). Let the vehicle go slowly down the hill with all four wheels turning against ...

  • Page 413

    Warning! Abrasive material in any part of the brakes may cause excessive wear or unpredictable braking. You might not have full braking power when you need it to prevent a collision. If you have been operating your vehicle in dirty conditions, get your brakes checked and cleaned as necessary. • if y...

  • Page 414

    (evic) or ⬙driver information display (did)” in “getting to know your instrument cluster” for further informa- tion. Note: • even if the power steering assistance is no longer operational, it is still possible to steer the vehicle. Under these conditions there will be a substantial increase in steer...

  • Page 415

    Gross trailer weight (gtw) the gtw is the weight of the trailer plus the weight of all cargo, consumables and equipment (permanent or tem- porary) loaded in or on the trailer in its ⬙loaded and ready for operation ⬙ condition. The recommended way to measure gtw is to put your fully loaded trailer on...

  • Page 416

    Trailer sway control — mechanical the trailer sway control is a telescoping link that can be installed between the hitch receiver and the trailer tongue that typically provides adjustable friction associated with the telescoping motion to dampen any unwanted trailer swaying motions while traveling. ...

  • Page 417

    Warning! (continued) • weight distributing systems may not be compat- ible with surge brake couplers. Consult with your hitch and trailer manufacturer or a reputable rec- reational vehicle dealer for additional information. Trailer hitch classification the following chart provides the industry stand...

  • Page 418

    Trailer towing weights (maximum trailer weight ratings) the following chart provides the maximum trailer weight ratings towable for your given drivetrain. 1.4l turbo engine trailer towing is not recommended. Engine max. Gtw (gross trailer wt.) max. Tongue wt. (see note) 2.4l 2,000 lbs (900 kg) 200 l...

  • Page 419

    Trailer and tongue weight never exceed the maximum tongue weight stamped on your bumper or trailer hitch. Consider the following items when computing the weight on the rear axle of the vehicle: • the tongue weight of the trailer. • the weight of any other type of cargo or equipment put in or on your...

  • Page 420

    Towing requirements to promote proper break-in of your new vehicle drive- train components, the following guidelines are recom- mended: warning! Improper towing can lead to a collision. Follow these guidelines to make your trailer towing as safe as possible: • make certain that the load is secured i...

  • Page 421

    Warning! (continued) • total weight must be distributed between the tow vehicle and the trailer such that the following four ratings are not exceeded: 1. Gvwr 2. Gtw 3. Gawr 4. Tongue weight rating for the trailer hitch uti- lized. Caution! • do not tow a trailer at all during the first 500 miles (8...

  • Page 422

    • check for signs of tire wear or visible tire damage before towing a trailer. Refer to “tires – general information” in “maintaining and caring for your vehicle” for the proper inspection procedure. • when replacing tires, refer to “tires – general infor- mation” in “maintaining and caring for your...

  • Page 423

    Caution! If the trailer weighs more than 1,000 lbs (453 kg) loaded, it should have its own brakes and they should be of adequate capacity. Failure to do this could lead to accelerated brake lining wear, higher brake pedal effort, and longer stopping distances. Towing requirements — trailer lights an...

  • Page 424

    Towing tips before setting out on a trip, practice turning, stopping, and backing the trailer in an area located away from heavy traffic. Automatic transmission — if equipped the drive range can be selected when towing. The transmission controls include a drive strategy to avoid frequent shifting wh...

  • Page 425

    Autostick • when using the autostick shift control, select the highest gear that allows for adequate performance and avoids frequent downshifts. For example, choose “5” if the desired speed can be maintained. Choose “4” or “3” if needed to maintain the desired speed. • to prevent excess heat generat...

  • Page 426

    Recreational towing towing this vehicle behind another vehicle front wheel drive (fwd) four-wheel drive (4wd) towing condition wheels off the ground automatic transmission manual transmission manual/ automatic transmission flat tow none not allowed not allowed not allowed dolly tow rear not allowed ...

  • Page 427

    Recreational towing models with front-wheel drive (fwd) recreational towing is allowed only if the front wheels are off the ground. This may be accomplished using a tow dolly (front wheels off the ground) or vehicle trailer (all four wheels off the ground). If using a tow dolly, follow this procedur...

  • Page 428

    Models with four-wheel drive (4wd) recreational towing (with all four wheels on the ground, or using a towing dolly) is not allowed. This vehicle may be towed on a flatbed or vehicle trailer provided all four wheels are off the ground. Caution! Towing this vehicle with any of its wheels on the groun...

  • Page 429

    In case of emergency contents 䡵 hazard warning flashers . . . . . . . . . . .429 䡵 assist and 9–1–1 — if equipped . . . . . . . .429 䡵 bulb replacement . . . . . . . . . . . . . . . . . . .435 ▫ general information. . . . . . . . . . . . . . . . . . . .435 ▫ replacement bulbs . . . . . . . . . . . ....

  • Page 430

    ▫ tire service kit — if equipped . . . . . . . . . . . .489 䡵 jump starting . . . . . . . . . . . . . . . . . . . . . .493 ▫ preparations for jump start . . . . . . . . . . . . . .494 ▫ jump starting procedure . . . . . . . . . . . . . . . .495 䡵 enhanced accident response system . . . . . . . . .49...

  • Page 431

    Hazard warning flashers the hazard warning flasher switch is located on the switch bank below the radio. Push the switch to turn on the hazard warning flasher. When the switch is activated, all direc- tional turn signals will flash on and off to warn oncoming traffic of an emergency. Push the switch...

  • Page 432

    Warning! Always obey traffic laws and pay attention to the road. Some uconnect access services, including 9-1-1 and assist, will not work without an operable 1x (voice/data) or 3g (data) network connection. Note: • your vehicle may be transmitting data as authorized by the subscriber. • the assist a...

  • Page 433

    9-1-1 call 1. Push the 9-1-1 call button on the overhead console. Note: in case the 9-1-1 call button is pushed in error, there will be a 10 second delay before the 9-1-1 call system initiates a call to a 9-1-1 operator. To cancel the 9-1-1 call connection, push the 9-1-1 call button on the overhead...

  • Page 434

    Note: • your vehicle may be transmitting data as authorized by the subscriber. • once a connection is made between the vehicle’s 9-1-1 call system and the 9-1-1 operator, the 9-1-1 operator may be able to open a voice connection with the vehicle to determine if additional help is needed. Once the 9-...

  • Page 435

    Warning! (continued) during or after an accident), the uconnect features, apps and services, among others, will not operate. • modifications to any part of the 9-1-1 call system could cause the air bag system to fail when you need it. You could be injured if the air bag system is not there to help p...

  • Page 436

    Warning! (continued) • the occupant restraint control module turns on the air bag warning light on the instrument panel if a malfunction in any part of the system is detected. If the air bag warning light is illumi- nated, have an authorized dealer service the orc system immediately. Even if the 9-1...

  • Page 437

    Warning! Always obey traffic laws and pay attention to the road. Some uconnect access services, including 9-1-1 and assist, will not work without an operable 1x (voice/data) or 3g (data) network connection. Note: • your vehicle may be transmitting data as authorized by the subscriber • never place a...

  • Page 438

    Note: lens fogging can occur under certain atmo- spheric conditions. This will usually clear as atmospheric conditions change to allow the condensation to change back into a vapor. Turning the lamps on will usually accelerate the clearing process. Replacement bulbs interior bulbs lamps bulb number f...

  • Page 439

    Exterior bulbs lamps bulb number low beam/high beam headlamps h13 front position/daytime running lights (drl ) p21/5w front direction indicator lamps py21w front fog lamps h11 side indicators (front and side view mirror) wy5w tail/brake lights/turn indicators p21w center high mounted stop lamp (chms...

  • Page 440

    Replacing exterior bulbs headlamps hi/lo beam light halogen to replace the bulbs proceed as follows: 1. Open the engine compartment and remove the head- lamp bulb cap. Headlamp bulb cap 438 in case of emergency.

  • Page 441

    2. Rotate the headlamp bulb socket counterclockwise then pull outwards. 3. Push on the locking tab on the headlamp bulb connec- tor and remove the bulb and socket. Headlamp bulb socket headlamp bulb connector 8 in case of emergency 439.

  • Page 442

    4. Install the new headlamp bulb making sure it is properly locked. 5. Install the headlamp bulb and socket; turn it clockwise making sure it is properly locked. Warning! Carry out the operation of replacing lamps only with the engine off. Also make sure that the engine is cold, to avoid the danger ...

  • Page 443

    3. Remove the electrical connectors. Position light/daytime running light/fog light access 1 — screws 2 — access door electrical connectors 8 in case of emergency 441.

  • Page 444

    4. Rotate in a counterclockwise direction (on the left-hand socket) or in a clockwise direction (on the right-hand socket) and remove the bulb and bulb socket. 5. To replace the bulb gently push bulb and rotate counterclockwise. Position light/daytime running light assembly 1 — drl bulb socket 2 — t...

  • Page 445

    6. Insert the new bulb by pushing on it and turning it clockwise. Make sure the bulb is correctly locked in place. 7. Install the bulb and sockets and rotate them clockwise (right side) and clockwise (left side), making sure that it is properly locked. 8. Reconnect the electrical connectors. 9. Rein...

  • Page 446

    3. By pushing the electrical connector tab remove the electrical connector. 4. Rotate the bulb counterclockwise, and then replace the bulb. 5. Insert the new bulb in the socket, making sure the bulb is locked into place. 6. Reconnect the electrical connector. 7. Reinstall the access door. Fog light ...

  • Page 447

    Side indicators front side indicators to replace the bulb proceed as follows: 1. Operating from inside the engine compartment using a suitable tool release the retaining clip. 2. Remove lamp assembly by sliding it toward the out- side. Lamp retaining clip lamp assembly 8 in case of emergency 445.

  • Page 448

    3. Remove the electrical connector by pushing the tab then disconnect the electrical connector. 4. Rotate counterclockwise to release the bulb socket from the lamp assembly, and remove it. Electrical connector bulb socket 446 in case of emergency.

  • Page 449

    5. Remove the bulb from the socket 6. Insert the new bulb in the socket. 7. Reinstall the bulb and socket into the lamp assembly by turning it clockwise, making sure it is locked into place. 8. Reconnect the electrical connector. 9. Reinstall the lamp assembly on the car, making sure it is locked in...

  • Page 450

    Side indicators on external rear view mirrors – (if equipped) caution! The procedure is described as a guideline. For the replacement of the lamp it is recommended that you contact your authorized dealer. To replace the bulb proceed as follows: 1. Remove the mirror cap on the outside rear view mirro...

  • Page 451

    2. Remove the transparent lens assembly as shown. Removing the mirror cap transparent lens 8 in case of emergency 449.

  • Page 452

    3. Remove the bulb socket and bulb from the transparent lens assembly by rotating the socket counterclockwise. 4. Remove the bulb from the bulb socket by pulling the bulb straight out. Transparent lens assembly bulb and socket assembly 1 — bulb 2 — bulb socket 450 in case of emergency.

  • Page 453

    5. Insert the new bulb, making sure that it is locked into place 6. Reinstall the socket in to the transparent lens assembly. 7. Reinstall the cover on the outside rear view mirror, making sure it is locked into place. Rear tail lamps contain the following: • position lights • stop lights • directio...

  • Page 454

    4. Disconnect the electrical connector by pushing the release. 5. Remove the rear tail lamp, sliding it toward the outside as shown. Rear lamp fastener and electrical connector 1 — fastener 2 — electrical connector tail lamp removal 452 in case of emergency.

  • Page 455

    6. Unscrew the screws and remove the rear tail lamp holder. 7. Replace the bulb as necessary. Rear lamp assembly 1 — mounting screws rear tail lamp holder 1 — tail light 2 — reverse bulb 3 — position light/stop light/turn signal 8 in case of emergency 453.

  • Page 456

    8. Insert the new bulb, making sure it is properly locked; 9. Reassemble the lamp assembly on the rear tail lamp housing, tightening the screws. 10. Reposition the rear tail lamp on the car. 11. Secure the fastener of the rear tail lamp and reconnect the electrical connector. 12. Reinstall the door ...

  • Page 457

    2. Remove the bulbs from the individual side contacts. 3. Insert the new bulbs, and ensure that they are properly locked between the contacts. 4. Reinstall the license plate lens. Note: if removal the license plate lens using a screw- driver, be sure to cover the tip of the screwdriver with a cloth ...

  • Page 458

    Replacing interior bulbs front courtesy light to replace the bulbs proceed as follows: 1. Using a suitable tool remove the front courtesy light as shown. 2. Release the retainer clips and bulb housing as shown. Front courtesy light housing front courtesy bulb housing 1 — retaining clips 2 — bulb hou...

  • Page 459

    3. Replace the bulbs by pulling straight out of bulb housing. 4. Insert the new bulbs, making sure that they are properly locked. 5. Reassemble the bulb housing and courtesy light hous- ing making sure that they are properly locked. 6. Install the front courtesy light making sure that it is properly...

  • Page 460

    Dome light vanity mirror to replace the bulbs proceed as follows: 1. Lift the cover of the mirror and pull out the visor mirror light cover. 2. Replace the bulb, releasing it from the side contacts, and then insert the new bulb, making sure that it is properly locked between the contacts. 3. Reinsta...

  • Page 461

    Dome light glove compartment to replace the bulb proceed as follows: 1. Open the glove compartment; 2. Place your fingers inside the light assembly, pull the bulb to replace it. 3. Insert the new bulb, making sure it is properly locked. Bulb removal/installation 8 in case of emergency 459.

  • Page 462

    Rear dome light — without retractable roof to replace the bulbs proceed as follows: 1. Using a suitable tool release the lamp assembly at both the ends. 2. Open the flap and replace the bulb. 3. Insert the new bulb, locking it between the contacts. 4. Reinstall the dome light. Rear dome light housin...

  • Page 463

    Dome light — my sky to replace the bulbs proceed as follows: 1. Lower the handle in the direction shown remove the dome light. 2. Replace the bulb by removing it from the side contacts. 3. Insert the new bulb, locking it between the contacts. 4. Reinstall the dome light. Retractable roof light bulb ...

  • Page 464

    Interior cargo lights to replace the bulbs proceed as follows: 1. Open the luggage compartment and remove the dome light assembly. 2. Open the light cover and replace the bulb. 3. Close the light cover over the bulb. 4. Reinstall the dome light in its correct position. Warning! • before proceeding w...

  • Page 465

    Warning! (continued) the emitted light and you can also affect the life of the lamp. In case of accidental contact, rub the bulb with a cloth dampened with alcohol and allow to dry. Fuses warning! • when replacing a blown fuse, always use an ap- propriate replacement fuse with the same amp rating as...

  • Page 466

    General information the fuses protect electrical systems against excessive current. When a device does not work you must check the electrical circuit inside the fuse for a break/melt. Also please be aware that when using power outlets for extended periods of time with the engine off may result in ve...

  • Page 467

    Fuse removal to replace a fuse use the extractor attached to the fuse cover (located on the inside of the engine compartment fuse cover. Access to the fuses the fuses are grouped into four controllers located in the engine compartment, under the instrument panel and on the inside of the left side ca...

  • Page 468

    Engine compartment fuses/distribution unit the engine compartment fuse panel is located on the left side of the engine compartment. Engine compartment fuse cavities fuse panel & cover location 1 — mounting screw 2 — fuse cover 466 in case of emergency.

  • Page 469

    Removing fuse cover and locking screw proceed as follows: • slowly turn the screw counterclockwise. • slowly release the screw. • remove the fuse cover by sliding it upward. Mounting fuse cover and locking screw proceed as follows: • properly secure the fuse cover to the box, slide com- pletely from...

  • Page 470

    Cavity maxi fuse cartridge fuse micro fuse description f01 70 amp tan – – module body computer f02 70 amp tan – – module body computer, rear distribution units f03 – 20 amp blue – controller power supply body computer f04 – 30 amp pink – brake control electronics module f05 70 amp tan – – electric p...

  • Page 471

    Cavity maxi fuse cartridge fuse micro fuse description f08 – 30 amp pink – automatic transmission, gsm f09 – – 5 amp tan control module engine f10 – – 15 amp blue horn f11 – – 10 amp red – 1.4 engines 25 amp clear – 2.4 engines supply secondary loads f14 – – 7.5 amp brown heater ⬙blow by⬙ f14 – – 5 ...

  • Page 472

    Cavity maxi fuse cartridge fuse micro fuse description f17 – – 10 amp red – 1.4 engines 15 amp blue – 2.4 engines supply primary loads f18 – – 20 amp yellow 12v rear cargo outlet ignition powered f19 – – 7.5 amp brown air conditioner compressor f20 – – 5 amp tan electronic power four- wheel drive f2...

  • Page 473

    Cavity maxi fuse cartridge fuse micro fuse description f30 – – 20 amp yellow (customer in- stalled) 12v rear cargo outlet con- stant battery powered f83 – 40 amp green – air conditioning fan f84 – – 30 amp green power supply all wheel drive f87 – – 5 amp tan gear selector automatic transmission f88 ...

  • Page 474

    Body computer fuse center the controller is located at the left side of the steering column at the bottom of the instrument panel. For the fuse replacement see your authorized dealer. Body controller fuse cavities 472 in case of emergency.

  • Page 475

    Cavity mini fuse description f31 7.5 amp brown flashes/electrical movement front seats/fan air conditioning f33 20 amp yellow power window front (driver side) f34 20 amp yellow power window front (passenger side) f36 15 amp blue supply uconnect system, air conditioning, alarm, power folding outside ...

  • Page 476

    Cavity mini fuse description f49 7.5 amp brown supply parksense, spot lights front dome, mirror, electric motor retractable roof, heated front seats, stabilizer battery, esc system, esl f50 7.5 amp brown supply air bag f51 7.5 amp brown alarm power, front courtesy light, air conditioning compressor,...

  • Page 477

    Rear cargo fuse/relay distribution unit to access the fuses, remove the access door from the left rear panel of the rear cargo area. The fuses may be contained in two units. Fuse holder no. 1 is located closest to the rear of the vehicle and fuse holder no. 2 (if equipped with trailer towing) is loc...

  • Page 478

    Fuse holder no. 1 cavity mini fuse description f1 30 amp blue power inverter f2 20 amp yellow hifi audio system f3 20 amp yellow my sky f4 7.5 amp brown lumbar adjustment front seat (driver side) f5 30 amp green power seat (driver side) f6 7.5 amp brown power seat (driver side and passenger side) f7...

  • Page 479

    Fuse holder no. 2 cavity mini fuse description f1 10 amp red controller exterior lighting on trailer f5 15 amp blue controller exterior lighting lights (drivers side) f6 15 amp blue controller exterior lighting lights (passenger side) jacking and tire changing warning! • do not attempt to change a t...

  • Page 480

    Jack location/spare tire stowage the jack and tools are located in the rear storage com- partment if equipped, inside a special container. Jack and tools 1 — wheel bolt wrench 2 — jack 3 — emergency funnel 4 — wheel chocks 5 — screwdriver 6 — emergency allen key 478 in case of emergency.

  • Page 481

    1. Open the liftgate. 2. Lift the access cover using the load floor pull strap. 3. Remove the fastener securing the spare tire. 4. Remove the chocks. 5. Remove the jack and wheel bolt wrench. 6. Remove the spare tire. Warning! A loose tire or jack thrown forward in a collision or hard stop could end...

  • Page 482

    Warning! (continued) the road to avoid being hit when operating the jack or changing the wheel. 2. Turn on the hazard warning flasher. 3. Set the electric park brake. 4. Place the shift lever into park (automatic transmis- sion) or reverse (manual transmission). 5. Turn the ignition off to the stop/...

  • Page 483

    Warning! (continued) • do not let anyone sit in the vehicle when it is on a jack. • do not get under the vehicle when it is on a jack. If you need to get under a raised vehicle, take it to a service center where it can be raised on a lift. • only use the jack in the positions indicated and for lifti...

  • Page 484

    3. Before raising the vehicle, use the wheel bolt wrench to loosen, but not remove, the wheel bolts on the wheel with the flat tire. Turn the wheel bolts counter- clockwise one turn while the wheel is still on the ground. 4. Place the jack underneath the jacking location that is closest to the flat ...

  • Page 485

    Front jacking location front jacking engagement point 8 in case of emergency 483.

  • Page 486

    5. Raise the vehicle just enough to remove the flat tire. Warning! Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and (continued) rear jacking location rear jacking engagement point 484 in case of emergency.

  • Page 487

    Warning! (continued) hurt someone near it. Raise the vehicle only enough to remove the tire. 6. Remove the wheel bolts and tire. 7. Mount the spare tire. Caution! Be sure to mount the spare tire with the valve stem facing outward. The vehicle could be damaged if the spare tire is mounted incorrectly...

  • Page 488

    Note: • your vehicle may be equipped with a compact spare tire or a limited — use spare tire. For further infor- mation refer to “tires — general information” in “maintaining and caring for your vehicle”. • for vehicles so equipped, do not attempt to install a center cap or wheel cover on the compac...

  • Page 489

    Warning! A loose tire or jack thrown forward in a collision or hard stop could endanger the occupants of the ve- hicle. Always stow the jack parts and the spare tire in (continued) warning! (continued) the places provided. Have the deflated (flat) tire repaired or replaced immediately. Road tire ins...

  • Page 490

    3. Lower the vehicle to the ground by turning the jack handle counterclockwise. 4. Finish tightening the wheel bolts. Push down on the wrench while at the end of the handle for increased leverage. Tighten the wheel bolts in a star pattern until each wheel bolt has been tightened twice. Refer to “tor...

  • Page 491

    Tire service kit — if equipped if a tire is punctured, you can make a first emergency repair using the tire service kit located in the rear storage compartment inside the storage container. Remove the tire service kit from the vehicle, take it out from the bag and place it near the punctured tire. S...

  • Page 492

    Warning! (continued) – if the tire has any damage from driving with extremely low tire pressure. – if the tire has any damage from driving on a flat tire. – if the wheel has any damage. – if you are unsure of the condition of the tire or the wheel. • keep tire service kit away from open flames or he...

  • Page 493

    Push the tire service kit power button to the “i” position. The electric compressor will be turned on, sealant and air will inflate the tire. Minimum 26 psi (1.8 bar) of pressure should be reached within 20 minutes. If the pressure has not been reached turn off and remove the tire service kit, drive...

  • Page 494

    Warning! The metal end fitting from power plug may get hot after use, so it should be handled carefully. Note: replace the sealant canister prior to the expira- tion date at your authorized dealer. Warning! Store the sealant canister in its special compartment, away from sources of heat. Failure to ...

  • Page 495

    Jump starting if your vehicle has a discharged battery it can be jump- started using a set of jumper cables and a battery in another vehicle or by using a portable battery booster pack. Jump starting can be dangerous if done improperly so please follow the procedures in this section carefully. Note:...

  • Page 496

    Preparations for jump start the battery in your vehicle is located in the front of the engine compartment, behind the left headlight assembly. Note: the positive battery post is covered with a protective cap. Lift up on the cap to gain access to the positive battery post. Warning! • take care to avo...

  • Page 497

    Proceed as follows: 1. Set the electric park brake, shift the automatic trans- mission into park (manual transmission in neu- tral) and turn the ignition to stop/off. 2. Turn off the heater, radio, and all unnecessary electri- cal accessories. 3. If using another vehicle to jump start the battery, p...

  • Page 498

    3. Connect the negative (-) end of the jumper cable to the negative (-) post of the booster battery. 4. Connect the opposite end of the negative (-) jumper cable to a good engine ground (exposed metal part of the discharged vehicle’s engine) away from the battery and the fuel injection system. Warni...

  • Page 499

    4. Disconnect the opposite end of the positive (+) jumper cable from the positive (+) post of the vehicle with the discharged battery. If frequent jump starting is required to start your vehicle you should have the battery and charging system in- spected at your authorized dealer. Caution! Accessori...

  • Page 500

    • turn off the fuel pump heater. • turn off the hvac blower motor. • close the hvac circulation door. System reset procedure depending on the nature of the event the left and right turn signal lights, located in the instrument panel, may both be blinking and will continue to blink until the ignition...

  • Page 501

    6. Turn left turn signal switch on. Left turn light is on solid. Right turn light is on solid. 7. Turn left turn signal switch off. (turn signal switch must be placed in neutral state). Left turn light is off. Right turn light is off. 8. Turn ignition off. 9. Turn hazard flashers off (manually). Sys...

  • Page 502

    Caution! Driving with a hot cooling system could damage your vehicle. If the temperature gauge reads “h,” pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on the “h” and you hear continuous...

  • Page 503

    2. Apply the electric park brake. 3. Carefully separate the gear selector bezel and boot assembly from the center console. 4. Press and maintain firm pressure on the brake pedal. Gear selector bezel location removing gear selector bezel 8 in case of emergency 501.

  • Page 504

    5. Insert a small screwdriver or similar tool down into the gear selector override access hole (at the right front corner of the gear selector assembly), and push and hold the override release lever down. 6. Move the gear selector to the neutral position. 7. The vehicle may then be started in neutra...

  • Page 505

    3. Pull the steering wheel outward until it is in the end of the travel position, then lock the steering column in position and push the control handle up until fully engaged. 4. Using the special tool supplied (located in the tool bag), remove the screws in the lower steering column trim cover and ...

  • Page 506

    5. With one hand, pull down on the release tab and with the other, pull out the ignition key. Lower steering column cover 1 — trim screws release tab location 504 in case of emergency.

  • Page 507

    6. Once the key is removed, reinstall the steering column cover. Freeing a stuck vehicle if your vehicle becomes stuck in mud, sand or snow, it can often be moved using a rocking motion. Turn the steering wheel right and left to clear the area around the front wheels. For vehicles with automatic tra...

  • Page 508

    Whenever the transmission remains in neutral for more than two seconds, you must press the brake pedal to engage drive or reverse. Note: push the ⬙esc off⬙ switch (if necessary), to place the electronic stability control (esc) system in ⬙partial off ⬙ mode, before rocking the vehicle. Refer to “elec...

  • Page 509

    Warning! (continued) even failure, of the axle and tires. A tire could explode and injure someone. Do not spin your vehi- cle’s wheels faster than 30 mph (48 km/h) or for longer than 30 seconds continuously without stop- ping when you are stuck and do not let anyone near a spinning wheel, no matter ...

  • Page 510

    Proper towing or lifting equipment is required to prevent damage to your vehicle. Use only tow bars and other equipment designed for this purpose, following equip- ment manufacturer’s instructions. Use of safety chains is mandatory. Attach a tow bar or other towing device to main structural members ...

  • Page 511

    Front wheel drive (fwd) the manufacturer recommends towing your vehicle with all four wheels off the ground on a flatbed. If flatbed equipment is not available, this vehicle must towed with the front wheels off the ground (using a towing dolly, or wheel lift equipment with the front wheels raised). ...

  • Page 512

    Emergency tow hooks — if equipped if your vehicle is equipped with tow hooks, there will be one in the rear and two mounted on the front of the vehicle. The rear hook will be located on the driver’s side of the vehicle. Note: for off-road recovery, it is recommended to use both of the front tow hook...

  • Page 513

    Vehicles equipped with rke transmitter with an integrated vehicle key turn the ignition key to the mar/run and then stop/ off position, without removing it. By extracting the key this will automatically engage the steering wheel lock. Place the transmission into neutral. Vehicles with keyless enter-...

  • Page 514

    Caution! Tow hooks are for emergency use only, to rescue a vehicle stranded off road. Do not use tow hooks for tow truck hookup or highway towing. You could damage your vehicle. 512 in case of emergency.

  • Page 515

    Maintaining and caring for your vehicle contents 䡵 emissions inspection and maintenance programs . . . . . . . . . . . . . . . . . . . . . . . . . .515 䡵 replacement parts . . . . . . . . . . . . . . . . . .516 䡵 dealer service . . . . . . . . . . . . . . . . . . . . . .516 䡵 maintenance schedule . ...

  • Page 516

    ▫ brake system . . . . . . . . . . . . . . . . . . . . . . . .548 ▫ manual transmission — if equipped . . . . . . .551 ▫ automatic transmission — if equipped . . . . .552 ▫ appearance care and protection from corrosion . . . . . . . . . . . . . . . . . . . . . . . . . . .554 䡵 lifting a vehicle . . ...

  • Page 517

    Emissions inspection and maintenance programs in some localities, it may be a legal requirement to pass an inspection of your vehicle’s emissions control system. Failure to pass could prevent vehicle registration. For states that require an inspection and mainte- nance (i/m), this check verifies the...

  • Page 518

    The ignition or start the engine. This means that your vehicle’s obd ii system is not ready and you should not proceed to the i/m station. • the mil will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine. This means that your vehi...

  • Page 519

    Note: intentional tampering with emissions control systems may void your warranty and could result in civil penalties being assessed against you. Warning! You can be badly injured working on or around a motor vehicle. Only do service work for which you have the knowledge and the proper equipment. If...

  • Page 520

    Hours of engine run time, whichever comes first. The 350 hours of engine run or idle time is generally only a concern for fleet customers. Severe duty all models change engine oil at 4,000 miles (6,500 km) if the vehicle is operated in a dusty and off road environment or is operated predominately at...

  • Page 521

    Maintenance chart mileage or time passed (whichever comes first) 10,000 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 years 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers 16,000 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 ...

  • Page 522

    Mileage or time passed (whichever comes first) 10,000 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 years 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers 16,000 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,000 19...

  • Page 523

    Mileage or time passed (whichever comes first) 10,000 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 years 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers 16,000 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,000 19...

  • Page 524

    Mileage or time passed (whichever comes first) 10,000 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 years 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers 16,000 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,000 19...

  • Page 525

    Mileage or time passed (whichever comes first) 10,000 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 years 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers 16,000 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,000 19...

  • Page 526

    Mileage or time passed (whichever comes first) 10,000 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 years 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers 16,000 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,000 19...

  • Page 527

    Mileage or time passed (whichever comes first) 10,000 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 years 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers 16,000 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,000 19...

  • Page 528

    Mileage or time passed (whichever comes first) 10,000 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 years 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers 16,000 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,000 19...

  • Page 529

    • strictly comply with the spark plug replacement inter- val given in the “maintenance schedule” for spark plug replacement. • contact your authorized dealer if you have any ques- tions. Warning! • you can be badly injured working on or around a motor vehicle. Do only service work for which you have...

  • Page 530

    Engine compartment — 1.4l turbo engine 1 — air cleaner filter 4 — battery 7 — coolant pressure cap 2 — engine oil dipstick 5 — power distribution center (fuses) 8 — coolant pressure bottle 3 — brake fluid reservoir 6 — washer fluid reservoir 9 — oil fill cap 528 maintaining and caring for your vehic...

  • Page 531

    Engine compartment — 2.4l engine 1 — engine air cleaner filter 4 — brake fluid reservoir 7 — washer fluid reservoir 2 — engine oil dipstick 5 — battery 8 — coolant pressure cap 3 — engine oil fill cap 6 — power distribution center (fuses) 9 — coolant pressure bottle 9 maintaining and caring for your...

  • Page 532

    Maintenance procedures the pages that follow contain the required maintenance services determined by the engineers who designed your vehicle. Besides those maintenance items specified in the fixed maintenance schedule, there are other components which may require servicing or replacement in the futu...

  • Page 533

    After a fully warmed engine is shut off. Do not check oil level before starting the engine after it has sat overnight. Checking engine oil level when the engine is cold will give you an incorrect reading. Checking the oil while the vehicle is on level ground, and approximately five minutes after a f...

  • Page 534

    Engine oil selection — 1.4l turbo engine for best performance and maximum protection for tur- bocharged engines under all types of operating condi- tions, the manufacturer recommends synthetic engine oils that are api certified and meet the requirements of fca material standard ms-12991. Engine oil ...

  • Page 535

    The engine oil filler cap also shows the recommended engine oil viscosity for your engine. For information on engine oil filler cap location, refer to “engine compart- ment” in this section. Lubricants which do not have both the engine oil certi- fication mark and the correct sae viscosity grade num...

  • Page 536

    Engine air cleaner filter refer to the “maintenance schedule” in the “maintaining and caring for your vehicle” section for the proper maintenance intervals. Warning! The air induction system (air cleaner, hoses, etc.) can provide a measure of protection in the case of engine backfire. Do not remove ...

  • Page 537

    Warning! (continued) an output greater than 12 volts. Do not allow cable clamps to touch each other. • battery posts, terminals, and related accessories contain lead and lead compounds. Wash hands after handling. • the battery in this vehicle has a vent hose that should not be disconnected and shoul...

  • Page 538

    Warning! • use only refrigerants and compressor lubricants approved by the manufacturer for your air condi- tioning system. Some unapproved refrigerants are flammable and can explode, injuring you. Other unapproved refrigerants or lubricants can cause the system to fail, requiring costly repairs. Re...

  • Page 539

    Body lubrication locks and all body pivot points, including such items as seat tracks, door hinge pivot points and rollers, liftgate, tailgate, decklid, sliding doors and hood hinges, should be lubricated periodically with a lithium based grease, such as mopar spray white lube to assure quiet, easy ...

  • Page 540

    Note: life expectancy of wiper blades varies depending on geographical area and frequency of use. Poor perfor- mance of blades may be present with chattering, marks, water lines or wet spots. If any of these conditions are present, clean the wiper blades or replace as necessary. Service position str...

  • Page 541

    Front wiper blade removal/installation 1. Lift the front wiper arm upward to raise the wiper blade off of the windshield. 2. Push the release button on the arm of the wiper blade. 3. Push the wiper blade up the and remove it. 4. Install the wiper blade and firmly push the wiper blade until it snaps ...

  • Page 542

    Rear wiper blade removal/installation 1. Carefully lift the rear wiper arm upward to raise the wiper blade off of the liftgate glass. 2. Grab and hold the wiper arm closest to the wiper blade end while pushing the wiper blade towards the liftgate glass to unsnap the blade pivot pin from the wiper bl...

  • Page 543

    Have an authorized technician inspect the complete ex- haust system and adjacent body areas for broken, dam- aged, deteriorated, or mispositioned parts. Open seams or loose connections could permit exhaust fumes to seep into the passenger compartment. In addition, have the exhaust system inspected e...

  • Page 544

    Caution! (continued) performance, have your vehicle serviced promptly. Continued operation of your vehicle with a severe malfunction could cause the converter to overheat, resulting in possible damage to the converter and vehicle. Under normal operating conditions, the catalytic con- verter will not...

  • Page 545

    Cooling system warning! • when working near the radiator cooling fan, dis- connect the fan motor lead or turn the ignition switch to the off position. The fan is temperature controlled and can start at any time the ignition switch is in the on position. • you or others can be badly burned by hot eng...

  • Page 546

    Refer to the “maintenance schedule” for the proper maintenance intervals. Selection of coolant refer to “fluids, lubricants, and genuine parts” in the “technical data” section for further information. Caution! • mixing of engine coolant (antifreeze) other than specified organic additive technology (...

  • Page 547

    Adding coolant your vehicle has been built with an improved engine coolant (oat coolant conforming to ms.90032) that al- lows extended maintenance intervals. This engine cool- ant (antifreeze) can be used up to ten years or 150,000 miles (240,000 km) before replacement. To prevent reduc- ing this ex...

  • Page 548

    • some vehicles require special tools to add coolant properly. Failure to fill these systems properly could lead to severe internal engine damage. If any coolant is needed to be added to the system, please contact your local authorized dealer. • mixing engine coolant (antifreeze) types is not recom-...

  • Page 549

    With your local authorities to determine the disposal rules for your community. To prevent ingestion by ani- mals or children, do not store ethylene glycol-based engine coolant in open containers or allow it to remain in puddles on the ground. If ingested by a child or pet, seek emergency assistance...

  • Page 550

    • check the coolant freeze point in the radiator and in the coolant expansion bottle. If engine coolant (antifreeze) needs to be added, the contents of the coolant expansion bottle must also be protected against freezing. • if frequent engine coolant (antifreeze) additions are required, the cooling ...

  • Page 551

    Brake master cylinder the fluid level in the master cylinder should be checked when performing under hood services, or immediately if the “brake warning light” is on. Be sure to clean the top of the master cylinder area before removing the cap. If necessary, add fluid to bring the fluid level up to ...

  • Page 552

    Warning! • use only manufacturer’s recommended brake fluid. Refer to “fluids, lubricants, and genuine parts” in the “technical data” section for further information. Using the wrong type of brake fluid can severely damage your brake system and/or impair its performance. The proper type of brake flui...

  • Page 553

    Caution! Use of improper brake fluids will affect overall clutch system performance. Improper brake fluids may damage the clutch system resulting in loss of clutch function and the ability to shift the transmis- sion. Manual transmission — if equipped lubricant selection use only the manufacturers r...

  • Page 554

    Automatic transmission — if equipped selection of lubricant it is important to use the proper transmission fluid to ensure optimum transmission performance and life. Use only the manufacturer’s specified transmission fluid. Refer to “fluids, lubricants, and genuine parts” in “technical data” for flu...

  • Page 555

    Caution! Do not use chemical flushes in your transmission as the chemicals can damage your transmission compo- nents. Such damage is not covered by the new vehicle limited warranty. Fluid level check the fluid level is preset at the factory and does not require adjustment under normal operating cond...

  • Page 556

    Appearance care and protection from corrosion protection of body and paint from corrosion vehicle body care requirements vary according to geo- graphic locations and usage. Chemicals that make roads passable in snow and ice and those that are sprayed on trees and road surfaces during other seasons a...

  • Page 557

    • if insects, tar, or other similar deposits have accumu- lated on your vehicle, use mopar super kleen bug and tar remover to remove. • use a high quality cleaner wax, such as mopar cleaner wax to remove road film, stains and to protect your paint finish. Take care never to scratch the paint. • avoi...

  • Page 558

    Have your vehicle repaired as soon as possible. The cost of such repairs is considered the responsibility of the owner. • if you carry special cargo such as chemicals, fertilizers, de-icer salt, etc., be sure that such materials are well packaged and sealed. • if a lot of driving is done on gravel r...

  • Page 559

    Stain repel fabric cleaning procedure — if equipped stain repel seats may be cleaned in the following man- ner: • remove as much of the stain as possible by blotting with a clean, dry towel. • blot any remaining stain with a clean, damp towel. • for tough stains, apply mopar total clean, or a mild s...

  • Page 560

    Warning! Do not use volatile solvents for cleaning purposes. Many are potentially flammable, and if used in closed areas they may cause respiratory harm. Caution! Direct contact of air fresheners, insect repellents, suntan lotions, or hand sanitizers to the plastic, painted, or decorated surfaces of...

  • Page 561

    Glass surfaces all glass surfaces should be cleaned on a regular basis with mopar glass cleaner, or any commercial household-type glass cleaner. Never use an abrasive type cleaner. Use caution when cleaning the inside rear win- dow equipped with electric defrosters or windows equipped with radio ant...

  • Page 562

    Seat belt maintenance do not bleach, dye or clean the belts with chemical solvents or abrasive cleaners. This will weaken the fabric. Sun damage can also weaken the fabric. If the belts need cleaning, use a mild soap solution or lukewarm water. Do not remove the belts from the vehicle to wash them. ...

  • Page 563

    Lifting point locations 9 maintaining and caring for your vehicle 561.

  • Page 564

    Tire safety information tire markings note: • p (passenger) — metric tire sizing is based on u.S. Design standards. P-metric tires have the letter “p” molded into the sidewall preceding the size designa- tion. Example: p215/65r15 95h. • european — metric tire sizing is based on european design stand...

  • Page 565

    • high flotation tire sizing is based on u.S. Design standards and it begins with the tire diameter molded into the sidewall. Example: 31x10.5 r15 lt. Tire sizing chart example: example size designation: p215/65r15xl 95h, 215/65r15 96h, lt235/85r16c, t145/80d18 103m, 31x10.5 r15 lt p = passenger car...

  • Page 566

    Example: r = construction code – ⬙r⬙ means radial construction, or – ⬙d⬙ means diagonal or bias construction 15, 16, 18 = rim diameter in inches (in) service description: 95 = load index – a numerical code associated with the maximum load a tire can carry h = speed symbol – a symbol indicating the r...

  • Page 567

    Example: load identification: absence of the following load identification symbols on the sidewall of the tire indicates a standard load (sl) tire: • xl = extra load (or reinforced) tire, or • ll = light load tire or • c, d, e, f, g = load range associated with the maximum load a tire can carry at a...

  • Page 568

    Tire identification number (tin) the tin may be found on one or both sides of the tire, however, the date code may only be on one side. Tires with white sidewalls will have the full tin, including the date code, located on the white sidewall side of the tire. Look for the tin on the outboard side of...

  • Page 569

    Example: dot ma l9 abcd 0301 01 = number representing the year in which the tire was manufactured (two digits) – 01 means the year 2001 – prior to july 2000, tire manufacturers were only required to have one number to represent the year in which the tire was manufactured. Example: 031 could represen...

  • Page 570

    Tire terminology and definitions term definition b-pillar the vehicle b-pillar is the structural member of the body located behind the front door. Cold tire inflation pressure cold tire inflation pressure is defined as the tire pressure after the ve- hicle has not been driven for at least three hour...

  • Page 571

    Tire loading and tire pressure tire and loading information placard location note: the proper cold tire inflation pressure is listed on the driver’s side b-pillar or the rear edge of the driver’s side door. Example tire placard location (door) 9 maintaining and caring for your vehicle 569.

  • Page 572

    Tire and loading information placard this placard tells you important information about the: 1. Number of people that can be carried in the vehicle. 2. Total weight your vehicle can carry. 3. Tire size designed for your vehicle. Example tire placard location (b-pillar) tire and loading information p...

  • Page 573

    4. Cold tire inflation pressures for the front, rear, and spare tires. Loading the vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size, and co...

  • Page 574

    4. The resulting figure equals the available amount of cargo and luggage load capacity. For example, if “xxx” amount equals 1,400 lbs (635 kg) and there will be five 150 lb (68 kg) passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lbs (294 kg) (since 5 x 150 ...

  • Page 575

    9 maintaining and caring for your vehicle 573.

  • Page 576

    Warning! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. Tires — general information tire pressure proper tire inflation pressur...

  • Page 577

    Warning! (continued) • always drive with each tire inflated to the recom- mended cold tire inflation pressure. Both under-inflation and over-inflation affect the stability of the vehicle and can produce a feeling of sluggish response or over responsiveness in the steering. Note: • unequal tire press...

  • Page 578

    Judgement when determining proper inflation. Tires may look properly inflated even when they are under- inflated. • inspect tires for signs of tire wear or visible damage. Caution! After inspecting or adjusting the tire pressure, al- ways reinstall the valve stem cap. This will prevent moisture and ...

  • Page 579

    Tire pressures for high speed operation the manufacturer advocates driving at safe speeds and within posted speed limits. Where speed limits or condi- tions are such that the vehicle can be driven at high speeds, maintaining correct tire inflation pressure is very important. Increased tire pressure ...

  • Page 580

    Consult an authorized tire dealer for tire repairs and additional information. Damaged run flat tires, or run flat tires that have experienced a loss of pressure should be replaced imme- diately with another run flat tire of identical size and service description (load index and speed symbol). Tire ...

  • Page 581

    Warning! Do not use summer tires in snow/ice conditions. You could lose vehicle control, resulting in severe injury or death. Driving too fast for conditions also creates the possibility of loss of vehicle control. Snow tires some areas of the country require the use of snow tires during the winter....

  • Page 582

    Run flat tire reaches the run flat mode it has limited driving capabilities and needs to be replaced immedi- ately. A run flat tire is not repairable. It is not recommended driving a vehicle loaded at full capacity or to tow a trailer while a tire is in the run flat mode. See the tire pressure monit...

  • Page 583

    Warning! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause tire dam- age or failure. A tire could explode and injure some- one. Do not spin your vehicle’s wheels faster than 30 mph (48 km/h) for more than 30 seconds continu- ously when you are stuck, and do...

  • Page 584

    Worn to the tread wear indicators, the tire should be replaced. Refer to “replacement tires” in this section for further information. Life of tire the service life of a tire is dependent upon varying factors including, but not limited to: • driving style. • tire pressure - improper cold tire inflati...

  • Page 585

    Information placard or the vehicle certification label for the size designation of your tire. The load index and speed symbol for your tire will be found on the original equipment tire sidewall. See the tire sizing chart ex- ample found in the “tire safety information” section of this manual for mor...

  • Page 586

    Warning! (continued) • failure to equip your vehicle with tires having adequate speed capability can result in sudden tire failure and loss of vehicle control. Caution! Replacing original tires with tires of a different size may result in false speedometer and odometer read- ings. Tire chains (tract...

  • Page 587

    Warning! Using tires of different size and type (m+s, snow) between front and rear axles can cause unpredictable handling. You could lose control and have a collision. Caution! To avoid damage to your vehicle or tires, observe the following precautions: • because of restricted traction device cleara...

  • Page 588

    Tire rotation recommendations the tires on the front and rear of your vehicle operate at different loads and perform different steering, handling, and braking functions. For these reasons, they wear at unequal rates. These effects can be reduced by timely rotation of tires. The benefits of rotation ...

  • Page 589

    Caution! Proper operation of four-wheel drive vehicles de- pends on tires of equal size, type and circumference on each wheel. Any difference in tire size can cause (continued) caution! (continued) damage to the power transfer unit. Tire rotation schedule should be followed to balance tire wear. Sto...

  • Page 590

    • clean and protect the painted parts by applying pro- tective waxes. • clean and protect polished metal parts by applying protective waxes. • apply talcum powder to the front and rear wiper blades and leave raised from the glass. • cover the vehicle with an appropriate cover taking care not to dama...

  • Page 591

    Caution! Before removal of the positive and negative termi- nals to the battery, wait at least a minute with ignition switch in the off position and close the drivers door. When reconnecting the positive and negative terminals to the battery be sure the ignition switch is in the off position and the...

  • Page 593

    Technical data contents 䡵 vehicle identification . . . . . . . . . . . . . . .592 ▫ chassis number . . . . . . . . . . . . . . . . . . . . . .592 䡵 wheel and tire torque specifications . . . . . . . . . . . . . . . . . . . . . .593 ▫ torque specifications . . . . . . . . . . . . . . . . . . .593 䡵 f...

  • Page 594

    Vehicle identification chassis number the chassis number (vin) is stamped on a plate located on the left front corner of the instrument panel cover, which is visible from outside the car through the wind- shield. This number is also stamped on the floor of the passenger compartment, near the right f...

  • Page 595

    A. Cover wheel and tire torque specifications proper lug nut/bolt torque is very important to ensure that the wheel is properly mounted to the vehicle. Any time a wheel has been removed and reinstalled on the vehicle the lug nuts/bolts should be torqued using a properly calibrated torque wrench. Tor...

  • Page 596

    Inspect the wheel mounting surface prior to mounting the tire and remove any corrosion or loose particles. Tighten the lug nuts/bolts in a star pattern until each nut/bolt has been tightened twice. After 25 miles (40 km) check the lug nut/bolt torque to be sure that all the lug nuts/bolts are proper...

  • Page 597

    Warning! To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts fully until the vehicle has been lowered. Failure to follow this warning may result in personal injury. Fluid capacities u.S metric fuel (approximate) 1.4l turbo/2.4l engine 12.7 gallons 48 liters engine oil ...

  • Page 598

    U.S metric cooling system * 1.4l turbo engine (mopar antifreeze/engine coolant 10 year/150,000 mile formula) 5.5 quarts 5.2 liters 2.4l engine (mopar antifreeze/engine coolant 10 year/ 150,000 mile formula) 6.8 quarts 6.5 liters * includes heater and coolant recovery bottle filled to max level. 596 ...

  • Page 599

    Fluids, lubricants, and genuine parts engine component fluid, lubricant, or genuine part engine coolant we recommend you use mopar antifreeze/coolant 10 year/150,000 mile formula oat (organic additive technology) or equivalent meeting the requirements of fca material standard ms.90032. Engine oil – ...

  • Page 600

    Chassis component fluid, lubricant, or genuine part manual transmission – if equipped we recommend you use mopar c series manual & dual dry clutch transmission fluid. Automatic transmission – if equipped use only mopar zf 8&9 speed atf automatic transmission fluid, or equivalent. Failure to use the ...

  • Page 601

    Multimedia contents 䡵 cybersecurity. . . . . . . . . . . . . . . . . . . . . . .601 䡵 uconnect settings . . . . . . . . . . . . . . . . . .602 ▫ buttons on the faceplate. . . . . . . . . . . . . . . .604 ▫ buttons on the touchscreen. . . . . . . . . . . . . .604 ▫ customer programmable features — uc...

  • Page 602

    ▫ radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .647 ▫ media. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .648 ▫ phone. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .649 ▫ voice text reply . . . . . . . . . . . . . . . . . . . . . .651 ▫ navigation (6.5an) . ...

  • Page 603

    Cybersecurity your vehicle may be a connected vehicle and may be equipped with both wired and wireless networks. These networks allow your vehicle to send and receive infor- mation. This information allows systems and features in your vehicle to function properly. Your vehicle may be equipped with c...

  • Page 604

    Warning! (continued) may increase the possibility for vehicle systems to be breached. • as always, if you experience unusual vehicle be- havior, take your vehicle to your nearest authorized dealer immediately. Note: • fca or your dealer may contact you directly regarding software updates. • to help ...

  • Page 605

    Uconnect 5.0 buttons on the touchscreen and buttons on the faceplate 1 — uconnect buttons on the touchscreen 2 — uconnect buttons on the faceplate uconnect 6.5an buttons on the touchscreen and buttons on the faceplate 1 — uconnect buttons on the touchscreen 2 — uconnect buttons on the faceplate 11 m...

  • Page 606

    Buttons on the faceplate buttons on the faceplate are located below, and beside the uconnect system in the center of the instrument panel. In addition, there is a scroll/enter control knob located on the right side. Turn the control knob to scroll through menus and change settings (i.E., 30, 60, 90)...

  • Page 607

    Mode, press and release the preferred setting and make your selection. Once the setting is complete, either press the back arrow button on the touchscreen or the back button on the faceplate to return to the previous menu or press the “x” button on the touchscreen to close out of the settings screen...

  • Page 608

    • touchscreen beep when in this display, you may turn on or shut off the sound heard when a touchscreen button is pressed. Press the “touchscreen beep” button on the touchscreen until a check-mark appears next to the setting, showing that setting has been selected. Units after pressing the “units” b...

  • Page 609

    Choose from a 12 hour or 24 hour format. Press the corresponding arrow above and below the current time to adjust, then select “am” or “pm.” • show time status when in this display, you may turn on or shut off the digital clock in the status bar. To change the show time status setting press the “sho...

  • Page 610

    • parkview backup camera delay — if equipped press the “parkview backup camera delay” button on the touchscreen to turn the parkview delay on or off. • parkview backup camera active guide lines — if equipped when this feature is enabled, active (dynamic) grid lines are overlaid on the rear backup ca...

  • Page 611

    Pressure to avoid a potential frontal collision. The aba system becomes active at 5 mph (8 km/h). For further information, refer to “forward collision warning-plus (fcw+) with mitigation” in “safety.” • parksense — if equipped the parksense system will scan for objects behind the vehicle when the tr...

  • Page 612

    • lanesense warning — if equipped when this feature is selected, it sets the distance at which the steering wheel will provide feedback for potential lane departures. The ldw sensitivity can be set to provide either an “early,” “medium,” or “late” warning zone start point. For further information, r...

  • Page 613

    Note: if your vehicle has experienced any damage in the area where the sensor is located, even if the fascia is not damaged, the sensor may have become misaligned. Take your vehicle to an authorized dealer to verify sensor alignment. A sensor that is misaligned will result in the bsm not operating t...

  • Page 614

    Engine is shut off. To change the headlights off delay setting, press the headlights off delay button on the touchscreen, and choose either 0 sec, 30 sec, 60 sec or 90 seconds. The selected button will highlight indicating that the setting has been selected. • greeting lights when this feature is se...

  • Page 615

    Keyless entry (rke) transmitter. This feature may be selected with or without the sound horn on lock feature selected. To make your selection, press the “flash lights w/lock” button on the touchscreen, then choose “on” or “off.” doors & locks after pressing the “doors & locks” button on the touch- s...

  • Page 616

    • horn with remote start — if equipped press the “horn w/remote start” button on the touch- screen to change this display. When this feature is se- lected, the horn will sound when the remote start is activated. To make your selection, press the “sound horn with remote start” button on the touchscre...

  • Page 617

    Engine off options after pressing the “engine off options” button on the touchscreen the following settings will be available. • engine off power delay — if equipped when this feature is selected, the power window switches, radio, uconnect phone system (if equipped), dvd video system (if equipped), ...

  • Page 618

    • compass variance press “compass variance” on the touchscreen to change this setting. You will then be able to select a compass variance of 1 through 15 per the compass variance zone map figure. Compass variance is the difference between magnetic north and geographic north. To compensate for the di...

  • Page 619

    Metallic objects). A message will appear on the touch- screen when the compass has been successfully cali- brated. Note: keep magnetic materials away from the top of the instrument panel, such as mobile phones, laptops and radar detectors. This is where the compass module is located, and it can caus...

  • Page 620

    • loudness — if equipped loudness improves sound quality at lower volumes. To make your selection, press the “loudness” button on the touchscreen, then choose “yes” or “no.” the button will highlight indicating that the setting has been selected. • aux volume offset — if equipped this feature provid...

  • Page 621

    • subscription information new vehicle purchasers or lessees will receive a free limited time subscription to siriusxm satellite radio with your radio. Following the expiration of the free services, it will be necessary to access the information on the subscription information screen to re-subscribe...

  • Page 622

    Clear personal data after pressing the “clear personal data settings” button on the touchscreen the following settings will be avail- able: • clear personal data when this feature is selected it will remove all personal data including bluetooth devices and presets. To remove personal information, pr...

  • Page 623

    Or down arrow button on the right side of the screen will allow you to toggle up or down through the available settings. Display after pressing the “display” button on the touchscreen the following settings will be available: • display mode this feature will allow you to select one of the auto displ...

  • Page 624

    • touchscreen beep when in this display, you may turn on or shut off the sound heard when a touchscreen button (button on the touchscreen) is pressed. Press the “touchscreen beep” button on the touchscreen. Press the “on” or “off” button on the touchscreen to turn the touchscreen beep on or off. Uni...

  • Page 625

    Length, press the “voice response length” button on the touchscreen and select from “brief” or “detailed.” • show command list when in this display, you may change the show com- mand list settings. To change the show command list settings, press the “show command list” button on the touchscreen and ...

  • Page 626

    • set year this feature will allow you to set the year. To make your selection, press the “–” or “+” buttons on the touchscreen to adjust the year up or down. • set hours this feature will allow you to adjust the hours. The sync time with gps “on” button must not be selected. To make your selection,...

  • Page 627

    Experience, select the near setting. This warns you of a possible collision when you are much closer to the vehicle in front of you. To change the fcw+ status, press the “fwd collision warning” button and select the “near” or “far” button. • forward collision warning-plus (fcw+) active braking — if ...

  • Page 628

    Change the lanesense strength status, press the “lanesense strength” button and select from the “low,” “medium” or “high” buttons. For further information, refer to “lane departure warn- ing (ldw)” in “starting and operating.” • parksense — if equipped the parksense system will scan for objects behi...

  • Page 629

    Blind spot monitor (bsm) system is deactivated. To change the blind spot alert status, press the “blind spot alert” button and select from “off,” “lights” or “lights & chimes.” note: if your vehicle has experienced any damage in the area where the sensor is located, even if the fascia is not damaged...

  • Page 630

    Button on the touchscreen. Press the “parkview backup camera delay” button on the touchscreen to turn the parkview delay on or off. • brakes this feature provides a means for a technician or vehicle owner to utilize a vehicle integrated, menu driven sys- tem, to command the electric park brake retra...

  • Page 631

    Lights after pressing the “lights” button on the touchscreen the following settings will be available: • headlight sensitivity when this feature is selected, it allows the headlight sensitivity to be adjusted according to three levels: level 1 = minimum sensitivity level 2 = medium sensitivity level...

  • Page 632

    Make your selection, press the “auto high beams” button on the touchscreen, then choose “yes” or “no.” • daytime running lights when this feature is selected, the headlights will turn on while the engine is running. To make your selection, press the “daytime running lights” button on the touch- scre...

  • Page 633

    The headlights will also turn off when the wipers are turned off if they were turned on by this feature. To make your selection, press the “headlights with wipers” but- ton on the touchscreen, then choose “on” or “off.” doors & locks after pressing the “doors & locks” button on the touch- screen the...

  • Page 634

    • sound horn with start — if equipped when this feature is selected, the horn will sound when the remote start is activated. To make your selection, press the “sound horn with remote start” button on the touchscreen, then choose “on” or “off.” the button will highlight indicating that the setting ha...

  • Page 635

    Note: the seat will return to the memorized seat location (if recall memory with remote key unlock is set to on) when the remote keyless entry (rke) transmitter is used to unlock the door. Engine off options after pressing the “engine off options” button on the touchscreen the following settings wil...

  • Page 636

    Audio after pressing the “audio” button on the touchscreen the following settings will be available: • balance/fade when in this display you may adjust the balance and fade settings. Press and drag the speaker icon, use the arrows to adjust, or tap the speaker icon to readjust to the center. • equal...

  • Page 637

    To make your selection, press the “aux volume offset” button on the touchscreen, select any point on the scale between the “+” and “–” buttons on the touchscreen. • auto-on radio the radio automatically turns on when vehicle is in run or will recall whether it was on or off at last ignition off. To ...

  • Page 638

    Services, it will be necessary to access the information on the subscription information screen to re-subscribe. Press the “subscription info” button on the touchscreen to access the subscription information screen. Write down the sirius id numbers for your receiver. To reactivate your service, eith...

  • Page 639

    Uconnect radios for detailed information about your uconnect 3.0, 5.0 or 6.5an radio, refer to your uconnect supplement manual. Usb/media player control — if equipped this feature allows an external device to be plugged into the usb port or aux jack. Located below the heating ventilation and air con...

  • Page 640

    Refer to the uconnect radio supplement for external usb support capability. Center console usb port located in the center console is a second usb port. Note: depending on vehicle configuration, the usb port may be charge only, or media file capable. Steering wheel audio controls the remote sound sys...

  • Page 641

    The right-hand control is a rocker-type switch with a pushbutton in the center and controls the volume and mode of the sound system. Pushing the top of the rocker switch will increase the volume, and pushing the bottom of the rocker switch will decrease the volume. Pushing the center button will mak...

  • Page 642

    Media mode pushing the top of the switch once will go to the next track on the selected media (aux/usb, bluetooth). Pushing the bottom of the switch once will go to the beginning of the current track, or to the beginning of the previous track if it is within eight seconds after the current track beg...

  • Page 643

    Emitted is far less than the electromagnetic energy emit- ted by wireless devices such as mobile phones. However, the use of wireless radios may be restricted in some situations or environments, such as aboard airplanes. If you are unsure of restrictions, you are encouraged to ask for authorization ...

  • Page 644

    Uconnect voice recognition quick tips introducing uconnect start using uconnect voice recognition with these help- ful quick tips. It provides the key voice commands and tips you need to know to control your uconnect 3.0, 5.0 or 6.5an system. Uconnect 3.0 642 multimedia.

  • Page 645

    Uconnect 5.0 uconnect 6.5an 11 multimedia 643.

  • Page 646

    Get started all you need to control your uconnect system with your voice are the buttons on your steering wheel. 1. Visit uconnectphone.Com to check mobile device and feature compatibility and to find phone pairing in- structions. 2. Reduce background noise. Wind and passenger con- versations are ex...

  • Page 647

    Basic voice commands the basic voice commands below can be given at any point while using your uconnect system. Push the vr button . After the beep, say ѧ • cancel to stop a current voice session. • help to hear a list of suggested voice commands. • repeat to listen to the system prompts again. Noti...

  • Page 648

    Uconnect 5.0 uconnect 6.5an 646 multimedia.

  • Page 649

    Radio use your voice to quickly get to the am, fm or siriusxm satellite radio stations you would like to hear. (subscrip- tion or included siriusxm satellite radio trial required.) push the vr button . After the beep, say ѧ • tune to ninety-five-point-five fm. • tune to satellite channel hits 1. Tip...

  • Page 650

    Media uconnect offers connections via usb port, bluetooth and auxiliary ports (if equipped). Voice operation is only available for connected usb and ipod devices. (remote cd player optional and not available on all vehicles.) push the vr button . After the beep, say one of the following commands and...

  • Page 651

    Tip: for the uconnect 5.0 and 6.5an systems, press the browse button on the touchscreen to see all of the music on your ipod or usb device. Your voice command must match exactly how the artist, album, song and genre information is displayed. Phone making and answering hands-free phone calls is easy ...

  • Page 652

    Push the phone button . After the beep, say one of the following commands ѧ • call john smith. • dial 123-456-7890 and follow the system prompts. • redial (call previous outgoing phone number). • call back (call previous incoming phone number). Tip: when providing a voice command, push the phone but...

  • Page 653

    Voice text reply uconnect will announce incoming text messages. Push the phone button and say “listen.” (must have compatible mobile phone paired to uconnect system.) 1. Once an incoming text message is read to you, push the phone button . After the beep, say: “reply.” 2. Listen to the uconnect prom...

  • Page 654

    Tip: your mobile phone must have the full implementa- tion of the message access profile (map) to take advan- tage of this feature. For details about map, visit uconnectphone.Com. Apple iphone ios6 or later sup- ports reading incoming text messages only. Navigation (6.5an) the uconnect navigation fe...

  • Page 655

    Uconnect access* (6.5a/6.5an) warning! Some uconnect access services, including 9-1-1 and assist will not work without an operable 1x (voice/ data) or 3g (data) network connection. Note: your vehicle may be transmitting data as autho- rized by the subscriber. An included trial and/or subscription is...

  • Page 656

    Registration (6.5a/6.5an) 1. Push the assist button located in the overhead console. 2. Press the “uconnect care” button on the touchscreen. 3. A helpful uconnect care agent will register your vehicle and handle all of the details. Signing up is easy! Simply follow the steps above. Or, press the “ap...

  • Page 657

    Mobile app (6.5an) you’re only a few steps away from using remote com- mands and playing your favorite music in your vehicle. To link your internet radio accounts: 1. Download the uconnect access app from the app store or google play. 2. Open the app and tap create account. 3. Enter your email addre...

  • Page 658

    2. Listen to the prompt. After the beep, dictate the message you would like to send. Wait for uconnect to process your message. 3. The uconnect system will repeat your message and provide a variety of options to add to, delete, send or hear the message again. After the beep, tell uconnect what you’d...

  • Page 659

    Tip: once you perform a search, you can reorganize the results by selecting either the best match, rating or distance tab on the top of the touchscreen display. Siriusxm travel link (6.5an) need to find a gas station, view local movie listings, check a sports score or the 5 - day weather forecast? S...

  • Page 660

    Push the vr button . After the beep, say one of the following commands: • show fuel prices. • show 5 - day weather forecast. • show extended weather. Tip: traffic alerts are not accessible with voice com- mand. Siriusxm travel link 658 multimedia.

  • Page 661

    General information this device complies with fcc rules part 15 and industry canada rss-210. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference that may be received including interference that may cause...

  • Page 663

    Index 12.

  • Page 664

    About your brakes . . . . . . . . . . . . . . . . . . . . . . . .237 abs (anti-lock brake system) . . . . . . . . . . . . . . . .239 adding engine coolant (antifreeze) . . . . . . . . . . . .545 adding fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . .400 adding washer fluid . . . . . . ...

  • Page 665

    Anti-lock brake system (abs) . . . . . . . . . . . . . . . .239 anti-lock warning light . . . . . . . . . . . . . . . . . . . .205 appearance care . . . . . . . . . . . . . . . . . . . . . . . . .554 arming system (security alarm) . . . . . . . . . . . . . . .50 assist, hill start . . . . . . . . . ...

  • Page 666

    Bulbs, light . . . . . . . . . . . . . . . . . . . . . . . . . . . . .313 camera, rear . . . . . . . . . . . . . . . . . . . . . . . . . . . .382 capacities, fluid . . . . . . . . . . . . . . . . . . . . . . . . . .595 caps, filler oil (engine) . . . . . . . . . . . . . . . . . . . . . . . . . . .53...

  • Page 667

    Clutch fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . .549 coin holder . . . . . . . . . . . . . . . . . . . . . . . . . . . . .169 cold weather operation . . . . . . . . . . . . . . . . . . . .321 connector uci . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .637 univ...

  • Page 668

    Key fob . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53 remote . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53 remote keyless entry (rke) . . . . . . . . . . . . . . . .53 driver information display (did) instrument cluster . . . . . . . . . . . . . . . . . . . . . .2...

  • Page 669

    Jump starting . . . . . . . . . . . . . . . . . . . . . . . . . .493 oil . . . . . . . . . . . . . . . . . . . . . . . . . . .530, 595, 597 oil filler cap . . . . . . . . . . . . . . . . . . . . . . . . . .532 oil filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . .533 oil selection . . ...

  • Page 670

    Ethanol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .397 gasoline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .395 light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .204 materials added . . . . . . . . . . . . . . . . . . . . . . . .398 methanol . . . . ...

  • Page 671

    Hill descent control indicator . . . . . . . . . . . . . . . .245 hill start assist. . . . . . . . . . . . . . . . . . . . . . . . . . .244 hitches trailer towing . . . . . . . . . . . . . . . . . . . . . . . . .415 holder, coin. . . . . . . . . . . . . . . . . . . . . . . . . . . . .169 holder, cup...

  • Page 672

    Lock the vehicle’s doors . . . . . . . . . . . . . . .56, 631 passive entry . . . . . . . . . . . . . . . . . . . . . . . . . . .56 passive entry programming . . . . . . . . . . . . .56, 631 remote control . . . . . . . . . . . . . . . . . . . . . . . . .56 unlock from the driver’s side . . . . . . ...

  • Page 673

    High beam/low beam select . . . . . . . . . . . . . . .97 hill descent control indicator . . . . . . . . . . . . . .245 instrument cluster . . . . . . . . . . . . . . . . . . . . . . .94 intensity control . . . . . . . . . . . . . . . . . . . . . . . .103 interior . . . . . . . . . . . . . . . . . ....

  • Page 674

    Master cylinder (brakes) . . . . . . . . . . . . . . . . . . . .549 methanol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .397 mirrors heated . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84 outside . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82 rearvie...

  • Page 675

    Parksense system, rear . . . . . . . . . . . . . . . . . . . . .377 pets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .309 placard, tire and loading information . . . . . . . . . .570 power brakes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .237 inverter . . . ...

  • Page 676

    Remote starting exit remote start mode . . . . . . . . . . . . . . . . . . .47 uconnect customer programmable features . . . . .47 uconnect settings . . . . . . . . . . . . . . . . . . . . . . . .47 remote starting system. . . . . . . . . . . . . . . . . . . . . .44 replacement keys . . . . . . . . ...

  • Page 677

    Adjustable upper shoulder anchorage . . . . . . . .265 child restraint . . . . . . . . . . . . . . . . . . . . . . . . .289 front seat . . . . . . . . . . . . . . . . . . . . . .257, 259, 262 inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . .311 operating instructions . . . . . . . ....

  • Page 678

    Engine fails to start . . . . . . . . . . . . . . . . . . . . .320 remote . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44 starting and operating . . . . . . . . . . . . . . . . . . . . .319 starting procedures . . . . . . . . . . . . . . . . . . . . . . . .319 steering tilt column . ...

  • Page 679

    Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . .582 rotation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .586 safety . . . . . . . . . . . . . . . . . . . . . . . . . . . .562, 574 sizes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .563 snow tires . . ...

  • Page 680

    Uci connector . . . . . . . . . . . . . . . . . . . . . . . . . . .637 uconnect customer programmable features . . . . . . . . . . . .47 uconnect settings . . . . . . . . . . . . . . . . . . . . . . . .47 uconnect settings . . . . . . . . . . . . . . . . . . . . . . . . . .33 customer programmable f...

  • Page 681

    Installation of radio transmitting equipment special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained person- nel. The following must be obs...

  • Page 682

    First edition printed in u.S.A. Stick with the specialists ® 16mk74-126-aa ©2015 fca us llc. All rights reserved. Jeep is a registered trademark of fca us llc. 16bu-126-ab second edition.