1. DL manuals
  2. Jeep
  3. Automobile
  4. Wrangler 2013
  5. Owner's Manual

Jeep Wrangler 2013 Owner's Manual

Other manuals for Wrangler 2013: User Manual, User Manual, Owner's Manual

Summary of Wrangler 2013

  • Page 1

    Wrangler includes wrangler unlimited chrysler group llc o w n e r ’ s m a n u a l 20 13 w rangler 13jk72-126-af sixth edition printed in u.S.A. 2 0 1 3.

  • Page 2

    Vehicles sold in canada with respect to any vehicles sold in canada, the name chrysler group llc shall be deemed to be deleted and the name chrysler canada inc. Used in substitution therefore. Driving and alcohol drunken driving is one of the most frequent causes of accidents. Your driving ability c...

  • Page 3: Table Of Contents

    Table of contents section page 1 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 things to know before starting your vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 3 understanding the featu...

  • Page 5: Introduction

    Introduction contents 䡵 introduction . . . . . . . . . . . . . . . . . . . . . . . .4 䡵 rollover warning . . . . . . . . . . . . . . . . . . . .5 䡵 how to use this manual . . . . . . . . . . . . . .6 䡵 warnings and cautions . . . . . . . . . . . . . .8 䡵 vehicle identification number . . . . . . . ....

  • Page 6

    Introduction congratulations on selecting your new chrysler group llc vehicle. Be assured that it represents precision workmanship, distinctive styling, and high quality - all essentials that are traditional to our vehicles. This is a specialized utility vehicle. It can go places and perform tasks t...

  • Page 7

    This owner’s manual has been prepared with the assis- tance of service and engineering specialists to acquaint you with the operation and maintenance of your vehicle. It is supplemented by warranty information, and various customer-oriented documents. Please take the time to read these publications ...

  • Page 8

    Failure to use the driver and passenger seat belts pro- vided is a major cause of severe or fatal injury. In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt. Always buckle up. How to use this manual consult the table of contents to determine...

  • Page 9

    1 introduction 7.

  • Page 10

    Warnings and cautions this owners manual contains warnings against oper- ating procedures that could result in a collision or bodily injury. It also contains cautions against procedures that could result in damage to your vehicle. If you do not read this entire owners manual, you may miss important ...

  • Page 11

    Vehicle modifications/alterations warning! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a collision resulting in serious injury or death. 1 introduction 9.

  • Page 13: Contents

    Things to know before starting your vehicle contents 䡵 a word about your keys . . . . . . . . . . . . .15 ▫ ignition key removal . . . . . . . . . . . . . . . . . . .15 ▫ key-in-ignition reminder . . . . . . . . . . . . . . . .16 䡵 steering wheel lock — if equipped . . . .17 ▫ to manually lock the s...

  • Page 14

    䡵 illuminated entry — if equipped . . . . . .23 䡵 remote keyless entry (rke) — if equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . .24 ▫ to unlock the doors and swing gate . . . . . . .24 ▫ remote key unlock on first press . . . . . . . . . .24 ▫ to lock the doors and swing gate . . . ...

  • Page 15

    ▫ child-protection door lock system — rear doors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42 䡵 windows . . . . . . . . . . . . . . . . . . . . . . . . . . .43 ▫ power windows — if equipped . . . . . . . . . . .43 ▫ wind buffeting . . . . . . . . . . . . . . . . . . . . . . .45 䡵 r...

  • Page 16

    䡵 engine break-in recommendations . . . .99 䡵 safety tips . . . . . . . . . . . . . . . . . . . . . . . . .100 ▫ transporting passengers . . . . . . . . . . . . . . . . .100 ▫ exhaust gas . . . . . . . . . . . . . . . . . . . . . . . . .100 ▫ safety checks you should make inside the vehicle . . . . ...

  • Page 17

    A word about your keys the keys for your new vehicle are enclosed in a plastic bag with the key code number on it. If you received your keys without the bag, ask your authorized dealer to give you the number. The key code can also be obtained by your authorized dealer from your vehicle invoice. Igni...

  • Page 18

    Warning! • before exiting a vehicle, always apply the parking brake, shift the transmission into park, and re- move the key fob from the ignition. When leaving the vehicle, always lock your vehicle. • never leave children alone in a vehicle, or with access to an unlocked vehicle. • allowing children...

  • Page 19

    Steering wheel lock — if equipped your vehicle may be equipped with a passive steering wheel lock. This lock prevents steering the vehicle with- out the ignition key. If the steering wheel is moved approximately a half turn in either direction, and the key is not in the ignition, the steering wheel ...

  • Page 20

    Sentry key® the sentry key® immobilizer system prevents unau- thorized vehicle operation by disabling the engine. The system does not need to be armed or activated. Operation is automatic, regardless of whether the vehicle is locked or unlocked. The system uses ignition keys that have an embedded el...

  • Page 21

    Caution! The sentry key® immobilizer system is not compat- ible with some after-market remote starting systems. Use of these systems may result in vehicle starting problems and loss of security protection. All of the keys provided with your new vehicle have been programmed to the vehicle electronics...

  • Page 22

    Customer key programming if you have two valid sentry keys®, you can program new sentry keys® to the system by performing the following procedure: 1. Cut the additional sentry key® transponder blank(s) to match the ignition switch lock cylinder key code. 2. Insert the first valid key into the igniti...

  • Page 23

    General information the sentry key® system complies with fcc rules part 15 and with rss-210 of industry canada. Operation is subject to the following conditions: • this device may not cause harmful interference. • this device must accept any interference that may be received, including interference ...

  • Page 24

    To arm the system the vehicle security alarm will set when you use the remote keyless entry (rke) transmitter to lock the doors and swing gate, or when you use the power door lock switch while the door is open. After all the doors are locked and closed, the vehicle security light (located on the ins...

  • Page 25

    Note: • unlocking the doors with the manual door lock plung- ers or the driver’s door lock cylinder will not disarm the vehicle security alarm. • when the vehicle security alarm is armed, the interior power door lock switches will not unlock the doors. Illuminated entry — if equipped the courtesy li...

  • Page 26

    Remote keyless entry (rke) — if equipped this system allows you to lock or unlock the doors, swing gate, and activate the panic alarm from a maxi- mum distance of 66 ft (20 m) using a remote keyless entry (rke) transmitter. The rke transmitter does not need to be pointed at the vehicle to activate t...

  • Page 27

    • for vehicles not equipped with the evic, the remote unlock feature can be enabled or disabled by perform- ing the following steps: 1. Press and hold the lock button on a programmed rke transmitter. 2. Continue to hold the rke transmitter lock button for at least four seconds, but not longer than 1...

  • Page 28

    Sound horn on lock this feature will cause the horn to chirp when the doors are locked with the rke transmitter. This feature can be turned on or turned off. To change the current setting, proceed as follows: • for vehicles equipped with the evic, refer to “electronic vehicle information center (evi...

  • Page 29

    To turn off flash lights with lock this feature will cause the turn signal lights to flash when the doors are locked or unlocked with the rke transmit- ter. This feature can be turned on or turned off. To change the current setting, proceed as follows: • for vehicles equipped with the evic, refer to...

  • Page 30

    General information this device complies with part 15 of fcc rules and with rs-210 of industry canada. Operation is subject to the following conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference that may be received including interference that may...

  • Page 31

    2. Remove and replace the battery. Avoid touching the new battery with your fingers. Skin oils may cause battery deterioration. If you touch a battery, clean it with rubbing alcohol. 3. To reassemble the rke transmitter case, snap the two halves together. Remote starting system — if equipped this sy...

  • Page 32

    How to use remote start all of the following conditions must be met before the engine will remote start: • shift lever in park • doors closed • hood closed • hazard switch off • brake switch inactive (brake pedal not pressed) • ignition key removed from ignition switch • battery at an acceptable cha...

  • Page 33

    Remote start abort message on electronic vehicle information center (evic) — if equipped the following messages will display in the evic if the vehicle fails to remote start or exits remote start prema- turely: • remote start aborted — door ajar • remote start aborted — hood ajar • remote start abor...

  • Page 34

    Remote start will also cancel if any of the following occur: • the engine stalls or rpm exceeds 2500 • any engine warning lamps come on • the hood is opened • the hazard switch is pressed • the transmission is moved out of park • the brake pedal is pressed to exit remote start mode without driving t...

  • Page 35

    Upper half door window removal — if equipped grasp the half door window and pull upward. Upper half door window installation — if equipped 1. Grasp the half door window and line up the pins with the pockets in the lower door. 2. Push down to ensure the half door window is fully seated. Front door re...

  • Page 36

    1. Roll down the glass window to prevent any damage. 2. Remove the hinge pin screws from the upper and lower outside hinges (using a #t50 torx® head driver). Note: the hinge pin screws and nuts can be stowed in the rear cargo tray located under the rear loadfloor. 3. Unplug the wiring harness connec...

  • Page 37

    4. Unhook the door strap from the body hook. Be careful not to allow the door to swing fully open as the mirror may damage the paint. 5. With the door open, lift the door to clear the hinge pins from their hinges and remove the door. Note: doors are heavy; use caution when removing them. To reinstal...

  • Page 38

    1. Roll down the glass window to prevent any damage. 2. Remove the hinge pin screws from the upper and lower outside hinges (using a #t50 torx® head driver). Note: the hinge pin screws and nuts can be stowed in the rear cargo tray located under the rear loadfloor. 3. Slide the front seat(s) fully fo...

  • Page 39

    5. Unplug the wiring harness connector. Note: if the red latch on the connector is locked, push the red latch to the right until you can only see the latch on one end (right) of the connector. This will unlock the connector tab, allowing the tab to be pressed down and enabling the harness to be disc...

  • Page 40

    Door locks manual door locks all doors are equipped with an interior rocker-type door lock lever. To lock a door when leaving your vehicle, press the rocker lever forward to the lock position and close the door. To unlock the door press the rocker lever rearward. Manual door lock (full frame doors) ...

  • Page 41

    Note: the ignition key that is used to start the vehicle is used to lock or unlock the doors, swing gate, glove compartment, and console storage. Warning! • for personal security reasons and safety in a colli- sion, lock the vehicle doors when you drive, as well as when you park and leave the vehicl...

  • Page 42

    Power door locks — if equipped the power door lock switch is located on each front door panel. Press the switch forward to lock the doors, and rearward to unlock the doors. Warning! • for personal security reasons and safety in a colli- sion, lock the vehicle doors when you drive, as well as when yo...

  • Page 43

    Automatic door locks — if equipped the auto door lock feature default condition is enabled. When enabled, the door locks will lock automatically when the vehicle’s speed exceeds 15 mph (24 km/h). The auto door lock feature can be enabled or disabled by your authorized dealer per written request of t...

  • Page 44

    Child-protection door lock system — rear doors to provide a safer environment for small children riding in the rear seats, the rear doors are equipped with child- protection door lock system. To engage or disengage the child-protection door lock system 1. Open the rear door. 2. Insert the tip of the...

  • Page 45

    Note: for emergency exit with the system engaged, move the rocker lever rearward (unlocked position), roll down the window and open the door with the outside door handle. Windows power windows — if equipped the power window switches are located on the instru- ment panel below the radio. Press the sw...

  • Page 46

    Four-door models the lower left switch controls the left rear passenger window, and the lower right switch controls the right rear passenger window. Auto-down both the driver and front passenger window switches have an “auto-down” feature. Press the window switch past the first detent, release, and ...

  • Page 47

    Rear power windows — four-door models the rear passenger window switches are located on the back of the center floor console. Press the switch down- ward to open the window and upward to close the window. Wind buffeting wind buffeting can be described as the perception of pressure on the ears or a h...

  • Page 48

    To open the swing gate, press the button on the gate handle. Note: close the rear flip-up window before attempting to close the swing gate (hard top models only). Caution! Do not press on rear wiper blade when closing the rear flip-up window, as damage to the blade will result. Warning! Driving with...

  • Page 49

    Occupant restraints some of the most important safety features in your vehicle are the restraint systems: • three-point lap and shoulder belts for the driver and all passengers • advanced front air bags for driver and front passenger • supplemental seat-mounted side air bags (sab) — if equipped • an...

  • Page 50

    Note: the advanced front air bags have a multistage inflator design. This allows the air bag to have different rates of inflation based on several factors, including the severity and type of collision. Here are some simple steps you can take to minimize the risk of harm from a deploying air bag: 1. ...

  • Page 51

    4. Do not lean against the door or window. If your vehicle has side air bags, and deployment occurs, the side air bags will inflate forcefully into the space between you and the door. 5. If the air bag system in this vehicle needs to be modified to accommodate a disabled person, contact the customer...

  • Page 52

    Buckle up even though you are an excellent driver, even on short trips. Someone on the road may be a poor driver and cause a collision that includes you. This can happen far away from home or on your own street. Research has shown that seat belts save lives, and they can reduce the seriousness of in...

  • Page 53

    Warning! (continued) your seat belt safely and to keep your passengers safe, too. • two people should never be belted into a single seat belt. People belted together can crash into one another in a collision, hurting one another badly. Never use a lap/shoulder belt or lap belt for more than one pers...

  • Page 54

    3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” warning! • a belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your bel...

  • Page 55

    Warning! (continued) • a shoulder belt placed behind you will not protect you from injury during a collision. You are more likely to hit your head in a collision if you do not wear your shoulder belt. The lap and shoulder belt are meant to be used together. 4. Position the lap belt across your thigh...

  • Page 56

    Warning! • a lap belt worn too high can increase the risk of injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdo- men. Always wear the lap part of your seat belt as low as possible and keep it snug. • a twisted belt may not protect you properly. I...

  • Page 57

    Rear center lap/shoulder belt retractor lockout — four-door models only this feature is designed to lock the retractor whenever the 60% rear seatback is not fully latched. This prevents someone from wearing the rear center lap/shoulder belt when the rear seatback is not fully latched. Note: • if the...

  • Page 58

    Lap/shoulder belt untwisting procedure use the following procedure to untwist a twisted lap/ shoulder belt. 1. Position the latch plate as close as possible to the anchor point. 2. At about 6 to 12 in (15 to 30 cm) above the latch plate, grasp and twist the belt webbing 180 degrees to create a fold ...

  • Page 59

    Warning! Position the shoulder belt height adjusters so that the belt rests across the middle of your shoulder. Failure to adjust the safety belt properly could reduce the effectiveness of the seat belt and increase the risk of injury in a collision. As a guide, if you are shorter than average, you ...

  • Page 60

    If the passenger seating position is equipped with an alr and is being used for normal usage: only pull the belt webbing out far enough to comfortably wrap around the occupant’s mid-section so as to not activate the alr. If the alr is activated, you will hear a ratcheting sound as the belt retracts....

  • Page 61

    How to disengage the automatic locking mode unbuckle the combination lap/shoulder belt and allow it to retract completely to disengage the automatic locking mode and activate the vehicle sensitive (emergency) locking mode. Warning! • the belt and retractor assembly must be replaced if the seat belt ...

  • Page 62

    Seat belt pretensioners the seat belts for both front seating positions are equipped with pretensioning devices that are designed to remove slack from the seat belt in the event of a collision. These devices may improve the performance of the seat belt by assuring that the belt is tight about the oc...

  • Page 63

    Unbuckled while traveling at speeds greater than 5 mph (8 km/h), beltalert® will provide both audio and visual notification. The front passenger seat beltalert® is not active when the front passenger seat is unoccupied. Beltalert® may be triggered when an animal or heavy object is on the front passe...

  • Page 64

    Warning! Using a seat belt extender when not needed can increase the risk of injury in a collision. Only use when the seat belt is not long enough when it is worn low and snug, and in the recommended seating positions. Remove and store the extender when not needed. Supplemental restraint system (srs...

  • Page 65

    The advanced front air bags have a multistage inflator design. This allows the air bag to have different rates of inflation that are based on several factors, including the severity and type of collision. This vehicle may be equipped with driver and/or front passenger seat track position sensors tha...

  • Page 66

    Air bag system components your vehicle may be equipped with the following air bag system components: • occupant restraint controller (orc) • air bag warning light • steering wheel and column • instrument panel • knee impact bolster • driver advanced front air bag • passenger advanced front air bag •...

  • Page 67

    Warning! (continued) • do not put anything on or around the air bag covers or attempt to open them manually. You may damage the air bags and you could be injured because the air bags may no longer be functional. The protective covers for the air bag cushions are designed to open only when the air ba...

  • Page 68

    Supplemental seat-mounted side air bags (sab) — if equipped supplemental seat-mounted side air bags (sab) may provide enhanced protection to help protect an occupant during a side impact. The sab is marked with an air bag label sewn into the outboard side of the front seats. When the air bag deploys...

  • Page 69

    With your back against the seat back, use the seat belts properly, and use the appropriate sized child restraint, infant restraint or booster seat recommended for the size and weight of the child. The system includes side impact sensors that are cali- brated to deploy the sab air bags during impacts...

  • Page 70

    The advanced front air bags will not deploy in all frontal collisions, including some that may produce sub- stantial vehicle damage — for example, some pole colli- sions, truck underrides, and angle offset collisions. On the other hand, depending on the type and location of impact, advanced front ai...

  • Page 71

    It also includes diagnostics that will illuminate the instru- ment cluster air bag warning light if a malfunction is noted that could affect the air bag system. The diagnos- tics also record the nature of the malfunction. Warning! Ignoring the air bag warning light in your instru- ment panel could m...

  • Page 72

    Supplemental seat-mounted side air bags (sab) inflator units — if equipped the supplemental seat-mounted side air bags inflator units (if equipped) are designed to activate only in certain side collisions. The orc determines if a side collision requires the side air bags to inflate, based on several...

  • Page 73

    In order to reset the enhanced accident response system functions after an event, the ignition switch must be changed from ign on to ign off. If a deployment occurs the advanced front air bags are designed to deflate immediately after deployment. Note: front and/or side air bags will not deploy in a...

  • Page 74

    • do not drive your vehicle after the air bags have deployed. If you are involved in another collision, the air bags will not be in place to protect you. Warning! • deployed air bags and seat belt pretensioners can- not protect you in another collision. Have the air bags, seat belt pretensioner, and...

  • Page 75

    Warning! (continued) stickers to the steering wheel hub trim cover or the upper right side of the instrument panel. Do not modify the front bumper or vehicle body structure, or add aftermarket side steps or running boards. • you need proper knee impact protection in a colli- sion. Do not mount or lo...

  • Page 76

    Note: if the speedometer, tachometer, or any engine related gauges are not working, the occupant restraint controller (orc) may also be disabled. The air bags may not be ready to inflate for your protection. Promptly check the fuse block for blown fuses. Refer to the label located on the inside of t...

  • Page 77

    Note: edr data are recorded by your vehicle only if a non-trivial crash situation occurs; no data are recorded by the edr under normal driving conditions and no per- sonal data (e.G., name, gender, age, and crash location) are recorded. However, other parties, such as law en- forcement, could combin...

  • Page 78

    Before buying any restraint system, make sure that it has a label certifying that it meets all applicable safety standards. You should also make sure that you can install it in the vehicle where you will use it. Note: for additional information, refer to www.Seatcheck.Org or call 1–866–seatcheck. Ca...

  • Page 79

    Summary of recommendations for restraining children in vehicles child size, height, weight or age recommended type of child restraint infants and toddlers children who are two years old or younger and who have not reached the height or weight limits of their child restraint either an infant carrier ...

  • Page 80

    Infants and child restraints safety experts recommend that children ride rearward- facing in the vehicle until they are two years old or until they reach either the height or weight limit of their rear facing child safety seat. Two types of child restraints can be used rearward-facing: infant carrie...

  • Page 81

    Older children and child restraints children who are two years old or who have outgrown their rear-facing convertible child seat can ride forward- facing in the vehicle. Forward-facing child seats and convertible child seats used in the forward-facing direc- tion are for children who are over two ye...

  • Page 82

    Children too large for booster seats children who are large enough to wear the shoulder belt comfortably, and whose legs are long enough to bend over the front of the seat when their back is against the seatback, should use the seat belt in a rear seat. Use this simple 5-step test to decide whether ...

  • Page 83

    Recommendations for attaching child restraints restraint type combined weight of the child + child restraint use any attachment method shown with an “x” below latch – lower anchors only seat belt only latch – lower anchors + top tether anchor seat belt + top tether anchor rear-facing child restraint...

  • Page 84

    Lower anchors and tethers for children (latch) restraint system your vehicle is equipped with the child restraint anchor- age system called latch, which stands for lower anchors and tethers for children. The latch system has three vehicle anchor points for installing latch- equipped child seats. The...

  • Page 85

    Latch positions for installing child restraints in this vehicle latch positions (two-door models) lower anchorage symbol 2 anchorages per seating position top tether anchorage symbol latch positions (four-door models) lower anchorage symbol 2 anchorages per seating position top tether anchorage symb...

  • Page 86

    What is the weight limit (child’s weight + weight of the child restraint) for using the latch anchorage system to attach the child restraint? 65 lbs (29.5 kg) use the latch anchorage system until the combined weight of the child and the child restraint is 65 lbs (29.5 kg). Use the seat belt and teth...

  • Page 87

    Can two child restraints be attached using a common lower latch anchorage? No never “share” a latch anchorage with two or more child restraints. If the center position does not have dedicated latch lower anchorages, use the seat belt to in- stall a child seat in the center position next to a child s...

  • Page 88

    Locating the latch anchorages the lower anchorages are round bars that are found at the rear of the seat cushion where it meets the seatback, below the anchorage sym- bols on the seatback. They are just visible when you lean into the rear seat to install the child restraint. You will easily feel the...

  • Page 89

    Locating the latch anchorages in addition, there are tether strap anchors lo- cated behind each rear seatback, near to the floor. Latch anchorages (four-door models) tether strap mounting (two-door models) 2 things to know before starting your vehicle 87.

  • Page 90

    Latch-compatible child restraint systems will be equipped with a rigid bar or a flexible strap on each side. Each will have a hook or connector to attach to the lower anchorage and a way to tighten the connection to the anchorage. Forward-facing child restraints and some rear-facing infant restraint...

  • Page 91

    To install a latch-compatible child restraint 1. If the selected seating position has a switchable auto- matic locking retractor (alr) seat belt, stow the seat belt, following the instructions below. See the section “installing child restraints using the vehicle seat belt” to check what type of seat...

  • Page 92

    How to stow an unused alr seatbelt when using the latch attaching system to install a child restraint, stow all alr seat belts that are not being used by other occupants or being used to secure child restraints. An unused belt could injure a child if they play with it and accidentally lock the seatb...

  • Page 93

    Installing child restraints using the vehicle seat belt the seat belts in the passenger seating positions are equipped with either a switchable automatic locking retractor (alr) or a cinching latch plate or both. Both types of seat belts are designed to keep the lap portion of the seat belt tight ar...

  • Page 94

    Lap/shoulder belt systems for installing child restraints in this vehicle two-door models four-door models 92 things to know before starting your vehicle.

  • Page 95

    What is the weight limit (child’s weight + weight of the child restraint) for using the tether anchor with the seat belt to attach a forward facing child restraint? Weight limit of the child restraint always use the tether anchor when using the seat belt to install a forward facing child restraint, ...

  • Page 96

    Installing a child restraint with a switchable automatic locking retractor (alr) 1. Place the child seat in the center of the seating position. For some second row seats, you may need to recline the seat and/or raise the head restraint to get a better fit. 2. Pull enough of the seat belt webbing fro...

  • Page 97

    8. If the child restraint has a top tether strap and the seating position has a top tether anchorage, connect the tether strap to the anchorage and tighten the tether strap. Refer to “lower anchors and tethers for chil- dren (latch) restraint system” for directions to attach a tether anchor. 9. Test...

  • Page 98

    5. If the child restraint has a top tether strap and the seating position has a top tether anchorage, connect the tether strap to the anchorage and tighten the tether strap. Refer to “lower anchors and tethers for chil- dren (latch) restraint system” for directions to attach a tether anchor. 6. Test...

  • Page 99

    Installing child restraints using the top tether anchorage — second row captains chairs 1. Look behind the seating position where you plan to install the child restraint to find the tether anchorage. You may need to move the seat forward to provide better access to the tether anchorage. If there is ...

  • Page 100

    4. Remove slack in the tether strap according to the child restraint manufacturer’s instructions. Warning! • an incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchorage position directly behind the child seat to secure a child res...

  • Page 101

    Engine break-in recommendations a long break-in period is not required for the engine and drivetrain (transmission and axle) in your vehicle. Drive moderately during the first 500 miles (800 km). After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable. While crui...

  • Page 102

    Safety tips transporting passengers never transport passengers in the cargo area. Warning! • do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death. • it is extremely dangerous to ride in a cargo area, inside or outside of a v...

  • Page 103

    Warning! (continued) • if it is necessary to sit in a parked vehicle with the engine running, adjust your heating or cooling controls to force outside air into the vehicle. Set the blower at high speed. The best protection against carbon monoxide entry into the vehicle body is a properly maintained ...

  • Page 104

    Defroster check operation by selecting the defrost mode and place the blower control on high speed. You should be able to feel the air directed against the windshield. See your autho- rized dealer for service if your defroster is inoperable. Floor mat safety information always use floor mats designe...

  • Page 105

    Warning! (continued) • check mounting of mats on a regular basis. Always properly reinstall and secure floor mats that have been removed for cleaning. • always make sure that objects cannot fall into the driver footwell while the vehicle is moving. Ob- jects can become trapped under the brake pedal ...

  • Page 106

    Door latches check for positive closing, latching, and locking. Fluid leaks check area under vehicle after overnight parking for fuel, engine coolant, oil, or other fluid leaks. Also, if gasoline fumes are detected or if fuel, power steering fluid, or brake fluid leaks are suspected, the cause shoul...

  • Page 107: Contents

    Understanding the features of your vehicle contents 䡵 mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . .111 ▫ inside day/night mirror . . . . . . . . . . . . . . . .111 ▫ outside mirrors . . . . . . . . . . . . . . . . . . . . . .112 ▫ automatic dimming mirror — if equipped . . .113 ▫ p...

  • Page 108

    ▫ delete/erase “all” uconnect® phonebook entries . . . . . . . . . . . . . . . . . . . . . . . . . . . . .124 ▫ list all names in the uconnect® phonebook . .125 ▫ phone call features . . . . . . . . . . . . . . . . . . . .125 ▫ uconnect® phone features . . . . . . . . . . . . . . .128 ▫ advanced pho...

  • Page 109

    ▫ replacing the rear seat — two-door models . . . . . . . . . . . . . . . . . . . . . . . . . . . .165 ▫ 60/40 split folding rear seat — four-door models . . . . . . . . . . . . . . . . . . . . . . . . . . . .165 䡵 to open and close the hood . . . . . . . . .167 䡵 lights . . . . . . . . . . . . . . ...

  • Page 110

    ▫ to set a desired speed . . . . . . . . . . . . . . . . .182 ▫ to deactivate . . . . . . . . . . . . . . . . . . . . . . . .182 ▫ to resume speed . . . . . . . . . . . . . . . . . . . . .182 ▫ to vary the speed setting . . . . . . . . . . . . . . .182 ▫ to accelerate for passing . . . . . . . . . ....

  • Page 111

    ▫ front panel(s) installation . . . . . . . . . . . . . . . .213 ▫ front panel(s) installation with rear hard top removed . . . . . . . . . . . . . . . . . . . . . . . . . . .213 ▫ rear hard top removal . . . . . . . . . . . . . . . .214 ▫ rear hard top installation . . . . . . . . . . . . . . .217 ...

  • Page 112

    䡵 folding windshield . . . . . . . . . . . . . . . . .290 ▫ lowering the windshield and removing side bars . . . . . . . . . . . . . . . . . . . . . . . . . . .292 ▫ raising the windshield and replacing side bars . . . . . . . . . . . . . . . . . . . . . . . . . . .295 䡵 rear window features — hard ...

  • Page 113

    Mirrors inside day/night mirror a single ball joint mirror is provided in the vehicle. It is a twist on mirror that has a fixed position at the wind- shield. The mirror installs on the windshield button with a counterclockwise rotation and requires no tools for mounting. The mirror head can be adjus...

  • Page 114

    Outside mirrors to receive maximum benefit, adjust the outside mirror(s) to center on the adjacent lane of traffic with a slight overlap of the view obtained on the inside mirror. Warning! Vehicles and other objects seen in the passenger side convex mirror will look smaller and farther away than the...

  • Page 115

    Automatic dimming mirror — if equipped this mirror automatically adjusts for headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light to the left of the button will illuminate to indicate when the dimming feature is activa...

  • Page 116

    Power mirrors — if equipped the power mirror switch is located on the center of the instrument panel, below the climate controls. A rotary knob selects the left mirror, right mirror or off position. After selecting a mirror, move the knob in the same direction you want the mirror to move. Use the ce...

  • Page 117

    Vanity mirrors vanity mirrors are located on the sun visors. To use the mirrors, rotate the sun visor down and swing the mirror cover upward. Uconnect® phone — if equipped uconnect® phone is a voice-activated, hands-free, in- vehicle communications system. Uconnect® phone al- lows you to dial a phon...

  • Page 118

    For uconnect® customer support: • u.S. Residents - visit www.Uconnectphone.Com or call 1–877–855–8400. • canadian residents - visit www.Driveuconnect.Ca or call, 1-800-465–2001 (english) or 1-800-387-9983 (french). Uconnect® phone allows you to transfer calls between the system and your mobile phone...

  • Page 119

    Uconnect® phone button the radio or steering wheel controls (if equipped) will contain the two control buttons (uconnect® phone button and voice command button) that will enable you to access the system. When you press the button you will hear the word uconnect® followed by a beep. The beep is your ...

  • Page 120

    Operation voice commands can be used to operate the uconnect® phone and to navigate through the uconnect® phone menu structure. Voice commands are required after most uconnect® phone prompts. You will be prompted for a specific command and then guided through the available options. • prior to giving...

  • Page 121

    Help command if you need assistance at any prompt, or if you want to know your options at any prompt, say “help” following the beep. The uconnect® phone will play all the options at any prompt if you ask for help. To activate the uconnect® phone from idle, simply press the button and follow the audi...

  • Page 122

    • for identification purposes, you will be prompted to give the uconnect® phone a name for your mobile phone. Each mobile phone that is paired should be given a unique phone name. • you will then be asked to give your mobile phone a priority level between one and seven, with one being the highest pr...

  • Page 123

    • the system will prompt you to say the name of the person you want to call. • after the “ready” prompt and the following beep, say the name of the person you want to call. For example, you can say “john doe”, where john doe is a previ- ously stored name entry in the uconnect® phonebook or downloade...

  • Page 124

    • only the phonebook of the currently connected mobile phone is accessible. • only the mobile phone’s phonebook is downloaded. Sim card phonebook is not part of the mobile phonebook. • this downloaded phonebook cannot be edited or deleted on the uconnect® phone. These can only be edited on the mobil...

  • Page 125

    The uconnect® phone will allow you to enter up to 32 names in the phonebook with each name having up to four associated phone numbers and designations. Each language has a separate 32-name phonebook accessible only in that language. In addition, if equipped and supported by your phone, uconnect® pho...

  • Page 126

    Delete uconnect® phonebook entry note: editing phonebook entries is recommended when the vehicle is not in motion. • press the button to begin. • after the “ready” prompt and the following beep, say “phonebook delete”. • after you enter the phonebook delete menu, you will then be asked for the name ...

  • Page 127

    • after confirmation, the phonebook entries will be deleted. • note that only the phonebook in the current language is deleted. • automatic downloaded phonebook entries cannot be deleted or edited. List all names in the uconnect® phonebook • press the button to begin. • after the “ready” prompt and ...

  • Page 128

    Answer or reject an incoming call - no call currently in progress when you receive a call on your mobile phone, the uconnect® phone will interrupt the vehicle audio sys- tem, if on, and will ask if you would like to answer the call. Press the button to accept the call. To reject the call, press and ...

  • Page 129

    Place/retrieve a call from hold to put a call on hold, press the button until you hear a single beep. This indicates that the call is on hold. To bring the call back from hold, press and hold the but- ton until you hear a single beep. Toggling between calls if two calls are in progress (one active a...

  • Page 130

    Redial • press the button to begin. • after the “ready” prompt and the following beep, say “redial”. • the uconnect® phone will call the last number that was dialed from your mobile phone. Note: this may not be the last number dialed from the uconnect® phone. Call continuation call continuation is t...

  • Page 131

    • continue to follow the system prompts to complete the language selection. After selecting one of the languages, all prompts and voice commands will be in that language. Note: after every uconnect® phone language change operation, only the language-specific 32-name phone- book is usable. The paired...

  • Page 132

    • the uconnect® phone does slightly lower your chances of successfully making a phone call as to that for the mobile phone directly. Warning! To use you uconnect® phone system in an emer- gency, your mobile phone must be: • turned on, • paired to the uconnect® system, • and have network coverage. To...

  • Page 133

    Voice mail calling to learn how to access your voice mail, refer to “working with automated systems”. Working with automated systems this method is used in instances where one generally has to press numbers on the mobile phone keypad while navigating through an automated telephone system. You can us...

  • Page 134

    Note: • you may not hear all of the tones due to mobile phone network configurations. This is normal. • some paging and voice mail systems have system time out settings that are too short and may not allow the use of this feature. Barge in - overriding prompts the “voice command” button can be used ...

  • Page 135

    Dialing using the mobile phone keypad you can dial a phone number with your mobile phone keypad and still use the uconnect® phone (while dialing via the mobile phone keypad, the user must exercise caution and take precautionary safety measures). By dialing a number with your paired bluetooth® mobile...

  • Page 136

    Advanced phone connectivity transfer call to and from mobile phone the uconnect® phone allows ongoing calls to be trans- ferred from your mobile phone to the uconnect® phone without terminating the call. To transfer an ongoing call from your uconnect® phone paired mobile phone to the uconnect® phone...

  • Page 137

    Select another mobile phone this feature allows you to select and start using another phone paired with the uconnect® phone. • press the button to begin. • after the “ready” prompt and the following beep, say “setup select phone” and follow the prompts. • you can also press the button at any time wh...

  • Page 138

    Voice training for users experiencing difficulty with the system recog- nizing their voice commands or numbers, the uconnect® phone voice training feature may be used. To enter this training mode, follow one of the two following proce- dures: from outside the uconnect® phone mode (e.G., from radio m...

  • Page 139

    Voice command • for best performance, adjust the rearview mirror to provide at least ½ in (1 cm) gap between the overhead console (if equipped) and the mirror. • always wait for the beep before speaking. • speak normally without pausing, just as you would speak to a person sitting a few feet/meters ...

  • Page 140

    • even though international dialing for most number combinations is supported, some shortcut dialing number combinations may not be supported. • in a convertible vehicle, system performance may be compromised with the convertible top down. Far end audio performance • audio quality is maximized under...

  • Page 141

    Read messages: if you receive a new text message while your phone is connected to uconnect® phone, an announcement will be made to notify you that you have a new text message. If you wish to hear the new message: • press the button. • after the “ready” prompt and the following beep, say “sms read” o...

  • Page 142

    List of preset messages: 1. Yes 2. No 3. Where are you? 4. I need more direction. 5. L o l 6. Why 7. I love you 8. Call me 9. Call me later 10. Thanks 11. See you in 15 minutes 12. I am on my way 13. I’ll be late 14. Are you there yet? 15. Where are we meeting? 16. Can this wait? 17. Bye for now 18....

  • Page 143

    Turn sms incoming announcement on/off turning the sms incoming announcement off will stop the system from announcing the new incoming mes- sages. • press the button. • after the “ready” prompt and the following beep, say “setup, incoming message announcement,” you will then be given a choice to chan...

  • Page 144

    142 understanding the features of your vehicle.

  • Page 145

    3 understanding the features of your vehicle 143.

  • Page 146

    144 understanding the features of your vehicle.

  • Page 147

    Voice commands primary alternate (s) zero one two three four five six seven eight nine star (*) plus (+) pound (#) add location all call voice commands primary alternate (s) cancel confirmation prompts continue delete dial download edit emergency english erase all espanol francais help home language...

  • Page 148

    Voice commands primary alternate (s) list phones mobile mute mute off new entry no other pair a phone phone pairing pairing phonebook phone book previous record again redial voice commands primary alternate (s) return to main menu return or main menu select phone select send set up phone settings or...

  • Page 149

    General information this device complies with part 15 of the fcc rules and rss 210 of industry canada. Operation is subject to the following conditions: • changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment....

  • Page 150

    Warning! Any voice commanded system should be used only in safe driving conditions following all applicable laws. Your attention should be focused on safely operating the vehicle. Failure to do so may result in a collision causing serious injury or death. When you press the voice command button, you...

  • Page 151

    To hear the first available menu, press the voice com- mand button and say “help” or “main menu”. Commands the voice command system understands two types of commands. Universal commands are available at all times. Local commands are available if the supported radio mode is active. Changing the volum...

  • Page 152

    Radio am to switch to the am band, say “am” or “radio am”. In this mode, you may say the following commands: • “frequency #” (to change the frequency) • “next station” (to select the next station) • “previous station” (to select the previous station) • “radio menu” (to switch to the radio menu) • “m...

  • Page 153

    Disc mode to switch to the disc mode, say “disc”. In this mode, you may say the following commands: • “track” (#) (to change the track) • “next track” (to play the next track) • “previous track” (to play the previous track) • “main menu” (to switch to the main menu) usb mode to switch to usb mode, s...

  • Page 154

    • “play memos” (to play previously recorded memos) — during the playback you may press the voice com- mand button to stop playing memos. You pro- ceed by saying one of the following commands: – “repeat” (to repeat a memo) – “next” (to play the next memo) – “previous” (to play the previous memo) – “d...

  • Page 155

    Voice training for users experiencing difficulty with the system recog- nizing their voice commands or numbers the uconnect® voice “voice training” feature may be used. 1. Press the voice command button, say “system setup” and once you are in that menu then say “voice training.” this will train your...

  • Page 156

    Front seat adjustment the seat can be adjusted forward or rearward by using a bar located by the front of the seat cushion, near the floor. While sitting in the seat, lift up on the bar located under the seat cushion and move the seat forward or rearward. Release the bar once you have reached the de...

  • Page 157

    Warning! • adjusting a seat while driving may be dangerous. Moving a seat while driving could result in loss of control which could cause a collision and serious injury or death. • seats should be adjusted before fastening the seat belts and while the vehicle is parked. Serious injury or death could...

  • Page 158

    Front seatback recline lean forward before lifting the handle, then lean back to the desired position and release the handle. Lift the handle to return the seatback to an upright position. Warning! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your che...

  • Page 159

    To return the seat to a sitting position, rotate the seatback upright until it locks and push the seat rearward until the track locks. Easy entry lever easy entry seat 3 understanding the features of your vehicle 157.

  • Page 160

    Note: • the front passenger seats have a track memory, which returns the seat to just past the halfway point of the track regardless of its original position. • the recliner and easy entry levers should not be used during the automatic returning of the seat to its sitting position. Tip n’ slide seat...

  • Page 161

    Passenger seat in addition to easy entry, the front passenger seat is also equipped with tip n’ slide. This feature allows for easier entry for rear passengers. Pull upward on the recline lever and slide the entire seat forward (easy entry). Tip n’ slide easy entry lever 3 understanding the features...

  • Page 162

    With the seat forward, pull the entire seat assembly toward the instrument panel. Heated seats — if equipped on some models, the front driver and passenger seats may be equipped with heaters in both the seat cushions and seatbacks. There are two heated seat switches that allow the driver and passeng...

  • Page 163

    When the high-level setting is selected, the heater will provide a boosted heat level during the initial stages of operation. Then, the heat output will drop to the normal high-level. If the high-level setting is selected, the system will automatically switch to low-level after ap- proximately 60 mi...

  • Page 164

    Head restraints head restraints are designed to reduce the risk of injury by restricting head movement in the event of a rear impact. Head restraints should be adjusted so that the top of the head restraint is located above the top of your ear. Warning! The head restraints for all occupants must be ...

  • Page 165

    Rear head restraints the rear seat is equipped with nonadjustable head re- straints. Refer to “occupant restraints” in “things to know before starting your vehicle” for information on child seat tether routing. Fold and tumble rear seat — two-door models note: • prior to folding the rear seat, it ma...

  • Page 166

    2. Slowly flip the entire seat forward. 3. Return the seat to the normal position. 4. Raise the rear seatback using the assist strap and firmly lock the seat into position. Removing the rear seat — two-door models warning! • it is extremely dangerous to ride in a cargo area, inside or outside of a v...

  • Page 167

    2. Press down on the release bar on each side, and pull the seat out and away from the lower bracket. 3. Remove the seat from the vehicle. Replacing the rear seat — two-door models reverse the steps for removing the seat. Warning! • to help protect against personal injury, passengers should not be s...

  • Page 168

    Note: • prior to folding the rear seat, it may be necessary to reposition the front seat to its mid-track position. • be sure that the front seats are fully upright and positioned forward. This will allow the rear seat to fold down easily. Warning! • it is extremely dangerous to ride in a cargo area...

  • Page 169

    To raise the rear seat raise the seatback and lock it into place. If interference from the cargo area prevents the seatback from fully locking, you will have difficulty returning the seat to its proper position. Note: if the rear seatback is not fully latched, the center shoulder belt will not be ab...

  • Page 170

    To push down slightly on the hood before pushing the safety latch. Insert the support rod into the slot on the hood. To close the hood, remove the support rod from the hood panel and place it in the retaining clip. Lower the hood slowly. Secure both of the hood latches. Warning! Be sure the hood is ...

  • Page 171

    Headlights and parking lights turn the end of the multifunction lever to the first detent for parking light operation. Turn to the second detent for headlight operation. Multifunction lever headlight switch 3 understanding the features of your vehicle 169.

  • Page 172

    Automatic headlights — if equipped this system automatically turns the headlights on or off according to ambient light levels. To turn the system on, turn the end of the multifunction lever to the auto position (third detent). When the system is on, the headlight time delay feature is also on. This ...

  • Page 173

    Turn signals move the multifunction lever up or down and the arrows on each side of the instrument cluster flash to show proper operation of the front and rear turn signal lights. Note: • if either light remains on and does not flash, or there is a very fast flash rate, check for a defective outside...

  • Page 174

    High/low beam switch push the multifunction lever away from you to switch the headlights to high beam. Pull the lever toward you, to switch the headlights back to low beam. Flash-to-pass you can signal another vehicle with your headlights by lightly pulling the multifunction lever toward you. This w...

  • Page 175

    Rotate the center portion of the lever upward to the last detent to turn on the interior lighting. Daytime running lights — if equipped the headlights come on at a low intensity level when shifted into any position other than park (auto trans- mission) or when the vehicle begins to move (manual tran...

  • Page 176

    Courtesy/reading lights two courtesy/reading lights are located in the bottom of the rearview mirror. You can turn these lights on and off from the switches in the mirror or from the dimmer control in the multifunction lever. These lights are also controlled auto- matically by the illuminated entry ...

  • Page 177

    The rear cargo light may be turned on by pressing the lens. Press the lens a second time to turn the light off. Sports bar reading light rear cargo light 3 understanding the features of your vehicle 175.

  • Page 178

    When a door is open and the interior lights are on, rotating the dimmer control to the extreme bottom posi- tion will cause all the interior lights to turn off. This is also known as the “party” mode because it allows the doors to stay open for extended periods of time without discharging the vehicl...

  • Page 179

    Windshield wiper operation rotate the end of the lever upward to the second detent past the intermittent settings for low-speed wiper opera- tion. Rotate the end of the lever upward to the third detent past the intermittent settings for high-speed wiper operation. Caution! In cold weather, always tu...

  • Page 180

    Note: the wiper delay times depend on vehicle speed. If the vehicle is moving less than 10 mph (16 km/h), delay times will be doubled. Windshield washers to use the washer, pull the lever toward you and hold while spray is desired. If the lever is pulled while in the delay range, the wiper will star...

  • Page 181

    Mist feature push down on the wiper lever to activate a single wipe to clear off road mist or spray from a passing vehicle. As long as the lever is held down, the wipers will continue to operate. Note: the mist feature does not activate the washer pump; therefore, no washer fluid will be sprayed on ...

  • Page 182

    Push down on the lever to unlock the steering column. With one hand firmly on the steering wheel, move the steering column up or down, as desired. Pull upwards on the lever to lock the column firmly in place. Warning! Do not adjust the steering column while driving. Adjusting the steering column whi...

  • Page 183

    Note: in order to ensure proper operation, the elec- tronic speed control system has been designed to shut down if multiple speed control functions are operated at the same time. If this occurs, the electronic speed control system can be reactivated by pushing the electronic speed control on/off but...

  • Page 184

    Warning! Leaving the electronic speed control system on when not in use is dangerous. You could accidentally set the system or cause it to go faster than you want. You could lose control and have an accident. Always leave the system off when you are not using it. To set a desired speed turn the elec...

  • Page 185

    Pressing the res (+) button once will result in a 1 mph (1.6 km/h) increase in set speed. Each subsequent tap of the button results in an increase of 1 mph (1.6 km/h). To decrease speed while the electronic speed control is set, push the set (-) button. If the button is continually held in the set (...

  • Page 186

    Electrical power outlet there are two 12 volt (13 amp) auxiliary power outlets that can provide power for accessories designed for use with the standard power outlet adapters. The front power outlet is powered from the ignition switch. Power is available when the ignition switch is in the on or acc ...

  • Page 187

    A second power outlet is located inside the center console and is powered directly from the vehicle battery. Caution! • do not exceed the maximum power of 160 watts (13 amps) at 12 volts. If the 160 watt (13 amp) power rating is exceeded the fuse protecting the system will need to be replaced. • pow...

  • Page 188

    Warning! To avoid serious injury or death: • only devices designed for use in this type of outlet should be inserted into any 12 volt outlet. • do not touch with wet hands. • close the lid when not in use and while driving the vehicle. • if this outlet is mishandled, it may cause an electric shock a...

  • Page 189

    Caution! • many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.E., mobile phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge suffi- ciently to degrade battery life and/or prevent the engine from starting. • ac...

  • Page 190

    Power inverter — if equipped there is a 115 volt, 150 watt inverter outlet located on the front of the center console to convert dc current to ac current. This outlet can power cellular phones, electron- ics and other low power devices requiring power up to 150 watts. Certain high-end video games, s...

  • Page 191

    The electrical device has been removed from the outlet the inverter should automatically reset. If the power rating exceeds approximately 170 watts, the power inverter may have to be reset manually. To reset the inverter manually press the power inverter button off and on. To avoid overloading the c...

  • Page 192

    Cupholders front cupholders the front cupholders are located in the center console. Rear cupholders the rear cupholders are located on the back of the center console. Front cupholders rear cupholders 190 understanding the features of your vehicle.

  • Page 193

    Storage glovebox storage the lockable glovebox storage compartment is located on the passenger side of the lower instrument panel. Pull outward on the handle/latch to open the compartment. Console storage compartment to lock or unlock the storage compartment, insert the ignition key and turn. To ope...

  • Page 194

    There is an extra storage area underneath the console lid. The console lid has an integrated paper clip feature that can hold small items. Rear storage compartment the rear cargo area storage compartment cover is held by a spring-loaded latch. In order to remove the rear storage compartment cover, u...

  • Page 195

    Dual top — two-door models — if equipped if your vehicle is equipped with a dual top, you must remove one of the tops from the vehicle. If the soft top is removed, the pivot brackets must also be removed from the sport bar. The soft top was installed at the factory for shipping purposes only. The so...

  • Page 196

    2. Remove the hard top. Refer to “freedom top three- piece modular hard top — front/rear panel re- moval” in this section. 3. Remove the soft top bow assembly pivot bracket screws (two per side) using a #t30 torx® head driver. 4. Disconnect the knuckles from the left and right metal pivot brackets. ...

  • Page 197

    5. Unzip the zipper on the sport bar cover to expose the pivot brackets. Remove the brackets using a #t30 torx® head driver. Recover and re-zip the sports bar cover. Store the pivot brackets and screws in a safe place. 6. Reinstall the hard top. Refer to “freedom top three- piece modular hard top — ...

  • Page 198

    2. Remove the hard top. Refer to “freedom top three- piece modular hard top — front/rear panel re- moval” in this section. 3. Install the door frames. Refer to “door frame” in this section. 4. If the soft top has been removed, follow these steps to reinstall the soft top. If the soft top is on the v...

  • Page 199

    Note: to aid in reattaching the knuckles, you may carefully tap on the knuckles using a rubber mallet. D. Screw the pivot screws back into place using a #t30 torx® head driver. Secure them until they are snug, being careful not to cross-thread the screws or overtighten. Caution! Do not overtighten t...

  • Page 200

    Note: be sure the wire harness in the left rear corner is not tangled in the soft top bows before you lift the top. 6. Unsnap and remove the black boot cover. This cover should be discarded. It was intended as a protective cover for shipping only. Note: a visual instruction sheet is enclosed in the ...

  • Page 201

    2. Remove the hard top. Refer to “freedom top three- piece modular hard top — front/rear panel re- moval” in this section. 3. Unbutton the side bow tether strap (both sides). 4. Using the plastic reinforcement as a handle, slide the tether strap up the side bow (both sides). 3 understanding the feat...

  • Page 202

    5. The tether strap must be hooked onto the pivot bracket prior to removal of soft top from vehicle (both sides). 6. Remove the soft top bow assembly pivot bracket screws (two per side) from the sport bar using a #t30 torx® head driver. 7. Lift the soft top in a upward motion to release the pivot br...

  • Page 203

    8. Remove the soft top from the vehicle and store in a clean, dry location (another person may be needed to help with this operation). Note: if you are doing this alone, use one arm to hold the bundle up, the other to remove the brackets. 9. Reinstall the hard top. Refer to “freedom top three- piece...

  • Page 204

    Installing the soft top — four-door models note: the following procedures are for first time set up only. For future soft top procedures, refer to “soft top” in this section. 1. Locate and remove the following items prior to hard top removal: • right and left door frames • six door frame attachment ...

  • Page 205

    5. Lower the pivot bracket onto the sport bar bracket mounting tab in a downward motion to lock into tab. 3 understanding the features of your vehicle 203.

  • Page 206

    6. Screw the pivot screws back into place using a #t30 torx® head driver. Secure them until they are snug, being careful not to cross-thread the screws or over- tighten. Caution! Do not overtighten the screws. You can strip the screws if they are overtightened. 7. Remove the tether strap from the pi...

  • Page 207

    8. Using the plastic reinforcement as a handle remove the tether strap from the bracket hook by sliding strap up off hook and slide down the side bow (both sides). 9. Button the side bow tether strap (both sides). 10. Remove the swing gate bar (black metal bar for bottom of rear window) and set asid...

  • Page 208

    Note: a visual instruction sheet is enclosed in the dual top wrap. 12. Put up the soft top. Refer to “soft top — putting up the soft top” in this section. Freedom top™ three-piece modular hard top — if equipped caution! • the hard top is not designed to carry any addi- tional loads such as roof rack...

  • Page 209

    Caution! (continued) • careless handling and storage of the removable roof panels may damage the seals, causing water to leak into the vehicles interior. • the front panel(s) must be positioned properly to ensure sealing. Improper installation can cause water to leak into the vehicles interior. Fron...

  • Page 210

    3. Turn the center l-shaped locks (two) from the center of the roof panel. 4. Turn the rear l-shaped lock (located above the shoul- der belt anchorage). 5. Unlatch the header panel latch located at the top of the windshield. 208 understanding the features of your vehicle.

  • Page 211

    6. Remove the left-hand panel. To remove the right panel, follow the steps above except for step 3. Freedom top™ storage bag vehicles equipped with a freedom top™ modular hard top, come with a freedom top™ storage bag that allows you to store your freedom top™ panels. The storage bag contains two co...

  • Page 212

    Insert the right side freedom panel into the bag with the latches facing downward. Unfold the black panel divider (ensure the divider is laying flat). Secure the velcro, located at the center of the divider. Insert the left-side freedom panel into the bag with the latches facing upward. 210 understa...

  • Page 213

    Note: ensure the front freedom panel latch is closed prior to inserting the panel into the bag. Unfold the outer flap and zip the freedom bag closed. 3 understanding the features of your vehicle 211.

  • Page 214

    Install the seat attachment strap (at the top of the bag) through the loops. Lift the freedom bag into the vehicle with the hooks and straps facing the back of the rear seat. Attach the clips at the bottom of the bag to the child restraint anchorages, located at the base of the rear seat. Wrap the u...

  • Page 215

    Front panel(s) installation note: set the panels on the windshield frame so that there is no overhang. Also, make sure that the panels are sitting flush with the body. 1. Install the right panel first, then the left panel. 2. Reinstall the panel(s) using the same steps for removal in reverse order. ...

  • Page 216

    Note: the front panel(s) must be positioned properly to ensure sealing. Set the panels on the windshield frame so that there is no overhang. Also, make sure that the panels are sitting flush with the body. 2. Install the right panel first, then the left panel. 3. Reinstall the panel(s) using the sam...

  • Page 217

    6. Locate the wire harness on the left rear inside corner of the vehicle. 7. Release the red locking tab by pulling outward to the right. Wire harness connector red locking tab 3 understanding the features of your vehicle 215.

  • Page 218

    8. To remove the wiring harness press the tab and pull downward to disconnect. 9. To remove the washer hose, pinch the grips on hose connector and pull downward. 10. Close the swing gate. 11. Remove the hard top from the vehicle. Place the hard top on a soft surface to prevent damage. Press tab to d...

  • Page 219

    Caution! The removal of the freedom top requires four adults located on each corner. Failure to follow this caution could damage the freedom top. Rear hard top installation note: if the door frames are installed from soft top usage, they must be removed prior to installation of the hard top. 1. Insp...

  • Page 220

    Caution! (continued) • careless handling and storage of the removable door frame(s) may damage the seals, causing water to leak into the vehicle’s interior. • the door frame(s) must be positioned properly to ensure sealing. Improper installation can cause water to leak into the vehicle’s interior. N...

  • Page 221

    Warning! Use both hands to remove the door frames. The door frames will fold and could cause injury if both hands are not used. 2. Place one hand on the upper rear and one hand on the front of the door frame. 3. Pull the frame toward you with your rearward hand to remove the frame from the vehicle. ...

  • Page 222

    4. Screw the knobs back into the door frame and fold for storage. Store in a secure location. Note: • do not drive your vehicle on pavement with the door frame(s) removed as you will lose the protection that they can provide. This procedure is furnished for use during off-road operation only. • do n...

  • Page 223

    3. After the door frame pin has been set into the body side hole, carefully set the front of the door frame into the rubber seal at the top of the windshield. 4. Starting with the front of the door frame, clip it over the metal side bar and then clip the rear, making sure that the material for the s...

  • Page 224

    5. Starting with the front knob, screw in and tighten both knobs. Repeat on the other side. Door frame installation — four-door models 1. Install the rear door frame first. 2. Set the door frame pin into the hole on top of the body side, just behind the rear door opening. 3. Position the top of the ...

  • Page 225

    4. Loosely install the rear knob (long knob) to hold the door rail in position. 5. Carefully set the front of the front door frame in the rubber seal at the top of the windshield. 6. Clip the front of the door rail over the side bar making sure that the material for the side bar cover is not pinched...

  • Page 226

    7. Position the rear of the front door frame to lay on top of the front of the rear door frame. Ensure the seals are installed correctly to avoid water leaks. 8. Loosely install both knobs beginning with the front knob (long knob). Then, install the middle knob (short knob) through the front and rea...

  • Page 227

    Soft top — two-door models please visit the owners section of jeep.Com for instruc- tional videos. Caution! The soft top is not designed to carry any additional loads such as roof racks, spare tires, building, hunting, or camping supplies, and/or luggage, etc. Also, it was not designed as a structur...

  • Page 228

    Caution! (continued) • refer to “appearance care for fabric top models” in “maintaining your vehicle” for further informa- tion. It contains important information on cleaning and caring for your vehicle’s fabric top. • do not use any tools (screwdrivers, etc.) to pry or force any of the clamps, clip...

  • Page 229

    Caution! (continued) • careless handling and storage of the soft top may damage the seals, causing water to leak into the vehicle’s interior. • the soft top must be positioned properly to ensure sealing. Improper installation can cause water to leak into the vehicle’s interior. Quick steps to loweri...

  • Page 230

    2. Remove the back window. 3. Release header latches from the windshield frame. 4. Release the sail panel retainers from the body side channel at the rear corners of the vehicle. 228 understanding the features of your vehicle.

  • Page 231

    Note: when releasing the sail panel retainers, it is helpful to pull down on the rear roof bow. 5. As you begin to lower the top, fold the sail panels so that they rest on top of the soft top. 3 understanding the features of your vehicle 229.

  • Page 232

    6. Release the sunrider® latch (both sides). 7. Open the swing gate and lower the top. Note: ensure fabric does not overhang the sides of the vehicle. 230 understanding the features of your vehicle.

  • Page 233

    Quick steps to raising the soft top refer to “raising the soft top” in this section for further information. 1. Open the swing gate and raise the top, engaging the sunrider® latches (another person may be needed to help with this operation). 3 understanding the features of your vehicle 231.

  • Page 234

    2. Engage header latches. 3. Install rear corner panels. 232 understanding the features of your vehicle.

  • Page 235

    4. Install the back window. 5. Install the side windows. 3 understanding the features of your vehicle 233.

  • Page 236

    6. Insert the front retainer of the window into the door channel, making sure the retainer is fully seated and properly positioned on the door frame. Failure to do so can result in wind and water leaks or damage to the window. 7. Insert the retainer along the bottom edge of the window into the botto...

  • Page 237

    Lowering the soft top 1 — header bow 6 — quarter window 2 — 2–bow 7 — check strap 3 — 3–bow 8 — front retainer — quarter window 4 — sail panel 9 — bottom retainer — quarter window 5 — body side retainer 3 understanding the features of your vehicle 235.

  • Page 238

    1 — zipper start 2 — zipper finish 3 — swing gate bar 4 — swing gate brackets 5 — sail panels 236 understanding the features of your vehicle.

  • Page 239

    Note: clean side and rear windows before removal to assist in preventing scratching during removal of the soft top. If zippers are difficult to operate due to road dust, etc., clean them with a mild soap solution and a small brush. Cleaning products are available through your authorized dealer. 1. I...

  • Page 240

    5. Before unzipping the rear window, release the first 3 in (7.6 cm) of both sail panels from the channel. Remove the swing gate bar by pulling it straight rearward out of the swing gate brackets. • unzip the rear window starting at the right lower corner of the window. Pull the zipper up, across th...

  • Page 241

    6. Remove the rear window retainer from the swing gate bracket on both the left and right sides. 7. Stow the windows carefully to avoid scratching. 8. Undo the velcro® that runs along the top and rear edge of the side window. 9. Beginning from the rear lower corner, completely unzip the window. 10. ...

  • Page 242

    11. Finish releasing the sail panel retainers from the body side channel at the rear corners of the vehicle. Note: when releasing the sail panel retainers, it is helpful to pull down on the rear roof bow. 12. As you begin to lower the top, fold the sail panels so that they rest on top of the soft to...

  • Page 243

    13. The swing gate brackets do not need to be removed unless the hard top is being installed. To remove the swing gate brackets, pull the front of the bracket forward while rolling the entire bracket back in toward the vehicle to disengage. 14. Completely release the latches from the loops on the wi...

  • Page 244

    15. Make sure the plastic sleeves are slid rearward over the sunrider® link (sunrider® models only). 16. Unlatch the side bows from both door rails (sun- rider® models only). 17. Before lowering the top, open the swing gate to prevent possible damage to the rear center high- mounted brake light. Mov...

  • Page 245

    18. Tuck the fabric and the check straps between the bows and as far inward as possible. This will keep any portion of the top from flapping outside of the vehicle. 19. Close the front header latches. 20. Remove the door frames, if desired. Refer to “door frame” in this section for further informati...

  • Page 246

    Raising the soft top 1. Unclip and move the sun visors to the side. 2. Install door frames, if removed. Refer to “door frame” in this section for further information. 3. Make sure the plastic sleeve is slid over sunrider® link (sunrider® models only). 4. Standing on the side of the vehicle, lift the...

  • Page 247

    5. Make sure the sunrider® bracket on the side bows latches to the door rails (sunrider® models only). 6. Open the header latches and engage the hook on each side onto the windshield loops (do not close the latches). 3 understanding the features of your vehicle 245.

  • Page 248

    7. If the swing gate brackets were removed, install them by hooking the rear edge of the bracket on the interior side of the body channel. Then, rotate it rearward and over the channel until it snaps onto the exterior part of the rail. To be properly located, the bracket must only be clipped to the ...

  • Page 249

    9. Partially install the sail panel retainers into the body side channel, leaving the last 3 in (7.6 cm) toward the rear window loose (on both sides). Pulling down on the rear roof bow (3–bow) will aid to reach the channel with the retainers. 10. To install the side windows, affix the window tempo- ...

  • Page 250

    11. Insert the front retainer of the window into the door channel, making sure the retainer is fully seated and properly positioned on the door frame. Failure to do so can result in wind and water leaks or damage to the window. 1 — incorrect insertion 2 — correct insertion 248 understanding the feat...

  • Page 251

    12. Insert the retainer along the bottom edge of the window into the bottom side channel, beginning at the front and working to the rear of the vehicle. Finish by closing the zipper completely and attaching the velcro® along the top and rear of the window. Repeat this step for the opposite side. 3 u...

  • Page 252

    13. Locate the black swing gate bar. Slide the swing gate bar over the receiver at the bottom inside of the rear window. The spongy part of the seal should be down and pointed outward to seal with the swing gate when closed. 14. Install the rear window by starting both zipper ends at the lower left ...

  • Page 253

    15. Run the zipper fully around to the right side of the window. 16. Grasp the swing gate bar and position it into the swing gate brackets. 3 understanding the features of your vehicle 251.

  • Page 254

    17. Insert the rear window retainer into the swing gate bracket on both the left and right sides. 18. Apply downward pressure on the top corner of the rear soft top bow (3–bow), then complete attaching the sail panel retainers into the body side channel. 19. Close the header latches and return the s...

  • Page 255

    Soft top — four-door models please visit the owner’s section of jeep.Com for instruc- tional videos. Caution! The soft top is not designed to carry any additional loads such as roof racks, spare tires, building, hunting, or camping supplies, and/or luggage, etc. Also, it was not designed as a struct...

  • Page 256

    Caution! (continued) • do not lower the top with the windows installed. Window and top damage may occur. • refer to “appearance care for fabric top models” in “maintaining your vehicle” for further informa- tion. It contains important information on cleaning and caring for your vehicle’s fabric top....

  • Page 257

    Caution! Failure to follow these cautions may cause interior water damage, stains or mildew on the top material: • it is recommended that the top be free of water prior to opening it. Operating the top, opening a door or lowering a window while the top is wet may allow water to drip into the vehicle...

  • Page 258

    Quick steps for lowering the soft top 1. Remove the side windows. 2. Remove the back window. Note: start zipper from the right side to remove back window. 3. Release header latches from the windshield frame. 256 understanding the features of your vehicle.

  • Page 259

    4. Release the sail panel retainers from the body side channel at the rear corners of the vehicle. Note: when releasing the sail panel retainers, it is helpful to pull down on the rear roof bow. 3 understanding the features of your vehicle 257.

  • Page 260

    5. Fold the sail panels so that they rest on top of the soft top. 6. Fold header rearward, pulling the fabric to the rear. 258 understanding the features of your vehicle.

  • Page 261

    7. Release sunrider® latch (both sides). 3 understanding the features of your vehicle 259.

  • Page 262

    8. Open the swing gate and lower the top. Note: ensure the fabric does not overhang the sides of the vehicle. Quick steps for raising the soft top 1. Open the swing gate and raise the top, engaging the sunrider® latches (another person may be needed to help with this operation). 260 understanding th...

  • Page 263

    2. Install rear corner panels. 3 understanding the features of your vehicle 261.

  • Page 264

    3. Rotate the header forward. 4. Engage the header latches. 262 understanding the features of your vehicle.

  • Page 265

    5. Install the back window. 6. Install the side windows. 3 understanding the features of your vehicle 263.

  • Page 266

    7. Insert the front retainer of the window into the door channel, making sure the retainer is fully seated and properly positioned on the door frame. Failure to do so can result in wind and water leaks or damage to the window. 8. Insert the retainer along the bottom edge of the window into the botto...

  • Page 267

    Folding down the soft top 1 — header bow 6 — body side retainer 2 — 2–bow 7 — quarter window 3 — 3–bow 8 — check strap 4 — 4–bow 9 — front retainer — quarter window 5 — sail panel 10 — bottom retainer — quarter window 3 understanding the features of your vehicle 265.

  • Page 268

    1 — zipper start 2 — zipper finish 3 — swing gate bar 4 — swing gate brackets 5 — sail panels 266 understanding the features of your vehicle.

  • Page 269

    Note: clean side and rear windows before removal to assist in preventing scratching during removal of the soft top. If zippers are difficult to operate due to road dust, etc., clean them with a mild soap solution and a small brush. Cleaning products are available through your authorized dealer. 1. I...

  • Page 270

    5. Before unzipping the rear window, release the first 3 in (7.6 cm) of both sail panels from the channel. Remove the swing gate bar by pulling it straight rearward out of the swing gate brackets. • unzip the rear window starting at the right lower corner of the window. Pull the zipper up, across th...

  • Page 271

    6. Remove the rear window retainer from the swing gate bracket on both the left and right sides. 7. Stow the windows carefully to avoid scratching. 8. Undo the velcro® that runs along the top and rear edge of the side window. 9. Beginning from the rear lower corner, completely unzip the window. 10. ...

  • Page 272

    11. Finish releasing the sail panel retainers from the body side channel at the rear corners of the vehicle. Note: when releasing the sail panel retainers, it is helpful to pull down on the rear roof bow. 12. Fold the sail panels so that they rest on top of the soft top. 270 understanding the featur...

  • Page 273

    13. The swing gate brackets do not need to be removed unless the hard top is being installed. To remove the swing gate brackets, pull the front of the bracket forward while rolling the entire bracket back in toward the vehicle to disengage. 14. Grasp the front side bow behind the header, and lift th...

  • Page 274

    15. Fold back the front section of the top, pulling the fabric rearward. Gently rest the header on top of the rear portion of the deck. 16. Fold the top so that the material forms a ⬙ w ⬙ as shown. Enter the vehicle and move the material into two folds. 17. Release the side bows by pressing down on ...

  • Page 275

    18. Before lowering the top, open the swing gate to prevent possible damage to the rear center high- mounted brake light. Grasp the folded side bows and slide the top along the door frame track to the rear door frame. 19. Gently slide the side bows off the door frame track and lower the top down int...

  • Page 276

    Note: help from another person will ease this operation. 20. Tuck the fabric and the check straps between the bows as far inside as possible. This will keep any portion of the top from flapping outside of the vehicle. 21. Once the top is fully down, use the velcro® straps provided to secure the top ...

  • Page 277

    Putting up the soft top note: be extremely careful when putting up the soft top to prevent the doors from getting scratched. It may be helpful to open the rear doors. 1. Install the door frames, if removed. Refer to “door frame” in this section for further information. 2. Undo the straps used to sec...

  • Page 278

    5. Insert the slider feature of the knuckles into the door frame tracks and slide the top forward. 6. Ensure that the top locks into the sunrider® locking mechanisms that are located above the front of the rear doors. 7. Unclip and move the sun visors to the side. 276 understanding the features of y...

  • Page 279

    8. Standing on the side of the vehicle, lift the top by the side bow until it rests on the windshield frame. 9. Open the header latches and engage the hook on each side onto the windshield loops (do not close the latches). 3 understanding the features of your vehicle 277.

  • Page 280

    10. If the swing gate brackets were removed, install them by hooking the rear edge of the bracket on the interior side of the body channel. Then, rotate it rearward and over the channel until it snaps onto the exterior part of the rail. To be properly located, the bracket must only be clipped to the...

  • Page 281

    Partially install the sail panel retainers into the body side channel, leaving the last 3 in (7.6 cm) toward the rear window loose (on both sides). Pulling down on the rear roof bow (4–bow) will aid in reaching the channel with the retainers. 12. To install the side windows, affix the window tem- po...

  • Page 282

    13. Insert the front retainer of the window into the door channel, making sure the retainer is fully seated and properly positioned on the door frame. Failure to do so can result in wind and water leaks or damage to the window. 1 — incorrect insertion 2 — correct insertion 280 understanding the feat...

  • Page 283

    14. Insert the retainer along the bottom edge of the window into the bottom side channel, beginning at the front and working to the rear of the vehicle. Finish by closing the zipper completely and attaching the velcro® along the top and rear of the window. Repeat this step for the opposite side. 3 u...

  • Page 284

    15. Locate the black swing gate bar. Slide the swing gate bar over the receiver at the bottom inside of the rear window. The spongy part of the seal should be down and pointed outward to seal with the swing gate when closed. 16. Install the rear window by starting both zipper ends at the lower left ...

  • Page 285

    18. Grasp the swing gate bar and position it into the swing gate brackets. 19. Insert the rear window retainer into the swing gate bracket on both the left and right sides. 20. Complete the installation of the sail panel by insert- ing the rest of the retainer into the body channel. 3 understanding ...

  • Page 286

    21. Close the header latches and return the sun visors to their secured position. Sunrider® (two-door models) — if equipped caution! Operating the top, opening a door or lowering a window while the top is wet may allow water to drip into the vehicle’s interior. Note: if you are going to be driving f...

  • Page 287

    Opening the sunrider® 1. Unclip and move the sun visors to the side. 2. Release the header latches from the loops on the windshield frame. 3. Slide the plastic sleeve forward. 4. Grasp the header and lift the top back. Make sure the material is folded back as shown. 3 understanding the features of y...

  • Page 288

    Note: the sunrider® latch on the door rail should not be activated for sunrider® use. If activated, the soft top must be reinstalled starting from the sail panels. 5. Locate the straps to secure the side bows. Wrap the straps around the bows as shown. Repeat on the other side. 6. Reposition the sun ...

  • Page 289

    Closing the sunrider® 1. Remove the straps from the side bows. 2. Unclip and move the sun visors to the side. 3. Grasp the front header and pull it to the front of the vehicle. 4. Hook the header latches to the loops on the wind- shield frame, close latches, and return the sun visors to their origin...

  • Page 290

    Opening the sunrider® 1. Unclip and move the sun visors to the side. 2. Release the header latches from the loops on the windshield frame. 3. Grasp the front side bow behind the header, and lift the top. 288 understanding the features of your vehicle.

  • Page 291

    4. Fold back the front section of the top and gently rest the header on top of the rear portion of the deck. 5. Fold the top so that the material forms a ⬙ w ⬙ as shown. Enter the vehicle and move the material into two folds. 3 understanding the features of your vehicle 289.

  • Page 292

    6. Secure the top by using the two provided straps. Each strap will wrap around the side bow and velcro® to itself; use one strap on each side of the vehicle. Closing the sunrider® perform the above steps in the opposite order. Note: failure to fold the fabric rearward will allow the material to sag...

  • Page 293

    If required for certain off-road uses, the side bars can be removed and the windshield folded down. However, the protection afforded by these features is then lost. If you remove the side bars and fold down the windshield, drive slowly and cautiously. It is recommended that the speed of the vehicle ...

  • Page 294

    Warning! (continued) • if you remove the doors, store them outside the vehicle. In the event of an accident, a loose door may cause personal injury. Lowering the windshield and removing side bars 1. Lower the fabric top or remove the hard top following the instructions in this manual. Note: to assis...

  • Page 295

    7. Remove the one hex bolt (13 mm) visible through the plastic trim on the bottom side of the side bar, one hex bolt (13 mm) on the side of the side bar, and one hex bolt (13 mm) on top of the side bar. Note: pull side bar out horizontally when removing. Caution! Do not remove the head impact foam f...

  • Page 296

    Warning! You or others could be injured if you carry the side bars loose in your vehicle. Remove the side bars from the vehicle or securely store them as described or they may cause personal injury if an accident occurs. See your authorized dealer for the cinch straps. 10. Remove the windshield wipe...

  • Page 297

    12. Lower the windshield gently until it contacts the rubber hood bumpers. 13. Secure the windshield by passing a cinch strap through the footman hoop on the center of the hood and on the center of the windshield frame. Tighten the strap to secure the windshield in place. Raising the windshield and ...

  • Page 298

    3. Attach the front of the side bar to the windshield frame. • install the top two hex bolts (13 mm) first, then the lower side hex bolt (13 mm). The lower side bolt will not align until the top two bolts are installed. 4. Tighten all side bar attachment bolts. 5. Install the lower windshield plates...

  • Page 299

    Rear window features — hard top only rear window wiper/washer — if equipped a rotary switch on the center portion of the control lever (located on the right side of the steering column) controls the operation of the rear wiper/washer function. Rotate the switch upward to the first detent position fo...

  • Page 300

    Rear window defroster — if equipped the rear window defroster button is located on the bottom right-side of the blower control knob. Press this button to turn on the rear window defroster. An indicator in the button will illuminate when the rear window defroster is on. The rear window defroster auto...

  • Page 301: Contents

    Understanding your instrument panel contents 䡵 instrument panel features . . . . . . . . . .302 䡵 instrument cluster . . . . . . . . . . . . . . . . .303 䡵 instrument cluster descriptions . . . . .304 䡵 compass and trip computer — if equipped . . . . . . . . . . . . . . . . . . . . . . . . . . .319 ...

  • Page 302

    ▫ system status . . . . . . . . . . . . . . . . . . . . . . . .335 ▫ personal settings (customer-programmable features) . . . . . . . . . . . . . . . . . . . . . . . . . . .335 䡵 uconnect® 230 — am/fm stereo radio and 6–disc cd/dvd changer (mp3/wma aux jack) . . . . . . . . . . . . . . . . . . . . ....

  • Page 303

    ▫ operation instructions — cd mode for cd and mp3 audio play . . . . . . . . . . . . . . . .375 ▫ notes on playing mp3 files . . . . . . . . . . . . . .377 ▫ list button (cd mode for mp3 play) . . . . . . .380 ▫ info button (cd mode for mp3 play) . . . . . .380 ▫ uconnect® (satellite radio) — if equ...

  • Page 304

    Instrument panel features 1 — air outlet 7 — climate controls 2 — instrument cluster 8 — power outlet 3 — radio 9 — lower switch bank 4 — assist handle 10 — power mirror switch — if equipped 5 — glove compartment 11 — horn 6 — power window switches 302 understanding your instrument panel.

  • Page 305

    Instrument cluster 4 understanding your instrument panel 303.

  • Page 306

    Instrument cluster descriptions 1. Fuel gauge the pointer shows the level of fuel in the fuel tank when the ignition switch is in the on/run position. 2. Charging system light this light shows the status of the electrical charg- ing system. The light should come on when the ignition switch is first ...

  • Page 307

    7. Seat belt reminder light when the ignition switch is first turned to on/ run, this light will turn on for four to eight seconds as a bulb check. During the bulb check, if the driver’s seat belt is unbuckled, a chime will sound. After the bulb check or when driving, if the driver seat belt remains...

  • Page 308

    Pull the lever toward you to switch the headlights back to low beam. If the driver’s door is open, and the headlights or park lights are left on, the high beam indicator light will remain illuminated and a chime will sound. 11. Brake warning light this light monitors various brake functions, includi...

  • Page 309

    Warning! Driving a vehicle with the red brake light on is dangerous. Part of the brake system may have failed. It will take longer to stop the vehicle. You could have a collision. Have the vehicle checked immediately. Vehicles equipped with the anti-lock brake system (abs), are also equipped with el...

  • Page 310

    13. Air bag warning light this light will turn on for four to eight seconds as a bulb check when the ignition switch is first turned to on/run. If the light is either not on during starting, stays on, or turns on while driving, have the system inspected at an authorized dealer as soon as possible. R...

  • Page 311

    17. Vehicle security light — if equipped this light will flash at a fast rate for approxi- mately 15 seconds, when the vehicle security alarm is arming, and then will flash slowly until the vehicle is disarmed. 18. Temperature gauge the temperature gauge shows engine coolant tempera- ture. Any readi...

  • Page 312

    19. Cruise indicator this indicator shows when the electronic speed control system is turned on. 20. 4wd indicator light — if equipped this light alerts the driver that the vehicle is in the four-wheel drive mode, and the front and rear driveshafts are mechanically locked to- gether forcing the fron...

  • Page 313

    Should stop and check your tires as soon as possible, and inflate them to the proper pressure. Driving on a signifi- cantly under-inflated tire causes the tire to overheat and can lead to tire failure. Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s han...

  • Page 314

    Caution! The tpms has been optimized for the original equipment tires and wheels. Tpms pressures and warning have been established for the tire size equipped on your vehicle. Undesirable system opera- tion or sensor damage may result when using re- placement equipment that is not of the same size, t...

  • Page 315

    Vehicle odometer messages when the appropriate conditions exist, the following odometer messages will display: eco . . . . . . . . . . . . . . . . . . . . . Fuel saver indicator door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Door ajar gate . . . . . . . . . . . . . . . . . . . . . . ...

  • Page 316

    Caution! Continuous driving with the transmission tempera- ture “hotoil” warning message illuminated will eventually cause severe transmission damage or transmission failure. Warning! If the transmission temperature “hotoil” warn- ing message is illuminated and you continue operat- ing the vehicle, ...

  • Page 317

    Change oil message your vehicle is equipped with an engine oil change indicator system. The “change oil” message will flash in the instrument cluster odometer for approximately 12 seconds after a single chime has sounded to indicate the next scheduled oil change interval. The engine oil change indic...

  • Page 318

    Certain conditions, such as a loose or missing gas cap, poor quality fuel, etc., may illuminate the light after engine start. The vehicle should be serviced if the light stays on through several typical driving styles. In most situations, the vehicle will drive normally and will not require towing. ...

  • Page 319

    Cycles, and the vehicle has been driven several miles (kilometers) at speeds greater than 30 mph (48 km/h), see your authorized dealer as soon as possible to have the problem diagnosed and corrected. Note: the “esc off indicator light” and the “esc activation/ malfunction indicator light” come on mo...

  • Page 320

    28. Sway bar indicator light — if equipped this indicator will illuminate when the front sway bar is disconnected. 29. Electronic stability control (esc) off indicator light — if equipped this light indicates the electronic stability con- trol (esc) is off. 30. Electronic throttle control (etc) ligh...

  • Page 321

    31. Electronic vehicle information center (evic) display / compass mini-trip computer display — if equipped when the appropriate conditions exist, this display shows the electronic vehicle information center (evic) messages. For further information, refer to “electronic vehicle information center”. ...

  • Page 322

    Control buttons the compass/temperature control buttons are located on the left spoke of the steering wheel. Press and release the step button on the steering wheel to access the options in the compass display. Note: the system will display the last known outside temperature when starting the vehicl...

  • Page 323

    Compass/temperature display note: if the vehicle is equipped with a chrysler uconnect® gps (navigation radio), the nav system will provide the compass direction, and the variance and calibration menus will be unavailable. The compass will perform accurately, based on gps signals instead of the earth...

  • Page 324

    To set the variance start the engine and leave the transmission gear selector lever in the park position. Press and hold the reset button on the steering wheel (for approximately ten sec- onds) until the current variance zone number is dis- played. To change the zone, press and release the step butt...

  • Page 325

    Note: • a good calibration requires a level surface and an environment free from large metallic objects such as buildings, bridges, underground cables, railroad tracks, etc. • magnetic materials should be kept away from the top of the center of the instrument panel. This is where the compass sensor ...

  • Page 326

    Trip conditions trip odometer (odo) / eco (fuel saver indicator) — if equipped this display shows the distance traveled since the last reset. Press and release the right button (on the instru- ment cluster) to switch from odometer to trip a or trip b or to eco. Press and hold the right button while ...

  • Page 327

    Trip b shows the total distance traveled for trip b since the last reset. Eco (fuel saver indicator) — if equipped the eco indicator will illuminate when you are driving in a fuel efficient manner and can be used to modify driving habits in order to increase fuel economy. Electronic vehicle informat...

  • Page 328

    This system conveniently allows the driver to select a variety of useful information by pressing the switches mounted on the steering wheel. The evic consists of the following: • compass heading (n, s, e, w, ne, nw, se, sw) • outside temperature (°f or °c) • eco display • fuel economy • miles/kilome...

  • Page 329

    Menu button press and release the menu button to advance the display to each of the evic main menu features or to return to the main menu from a sub-menu. Upon reaching the last item in the main menu the evic will advance to the first item in the main menu with the next menu button press and release...

  • Page 330

    Electronic vehicle information center (evic) displays when the appropriate conditions exist, the evic displays the following messages: • low tire pressure • service tpm system (refer to ⬙ tire pressure monitor- ing system ⬙ in ⬙ starting and operating ⬙ ) • premium tpm system graphic display • damag...

  • Page 331

    • check gascap (refer to “adding fuel” in “starting and operating” for more details) • oil change required (with a single chime) • eco (fuel saver indicator) — if equipped oil change required your vehicle is equipped with an engine oil change indicator system. The “oil change required” message will ...

  • Page 332

    Evic main menu to step to each main menu feature press and release the menu button once for each step. A step from the last item in the list will cause the first item in the feature list to be displayed. The following features are in the main menu: • compass, outside temperature, and eco display • a...

  • Page 333

    Note: the system will display the last known outside temperature when starting the vehicle and may need to be driven several minutes before the updated tempera- ture is displayed. Engine temperature can also affect the displayed temperature; therefore, temperature readings are not updated when the v...

  • Page 334

    Manual compass calibration if the compass appears erratic and the “cal” indicator does not appear in the evic display, you must put the compass into the calibration mode manually as follows: 1. Start the engine. Leave the shift lever in park in order to enter the evic programming menus. 2. Press the...

  • Page 335

    To change the compass variance: 1. Turn the ignition switch run (it is not necessary to start the engine). 2. Press the menu button until personal settings (customer-programmable features) displays in the evic. 3. Press the down button until “compass variance” message and the last variance zone numb...

  • Page 336

    Average fuel economy shows the average fuel economy since the last reset. Average fuel economy can be reset by pressing and holding the select button (as prompted in the evic display). Upon reset, the history information will be erased, and the averaging will continue from the last fuel average read...

  • Page 337

    Evic units selection (units in display) displays the units used for the outside temperature, average fuel economy and distance to empty features. Press and release the select button to toggle units between ⬙ u.S. ⬙ and ⬙ metric ⬙ . System status displays system ok if there are no active warning mess...

  • Page 338

    Auto lock doors when this feature is selected, all doors will lock auto- matically when the vehicle reaches a speed of 15 mph (24 km/h). The auto door lock feature can be enabled or disabled, to make your selection, press and release the select button until a check-mark appears next to the feature s...

  • Page 339

    Flash lamp with lock when on is selected, the front and rear turn signals will flash when the doors are locked or unlocked with the rke transmitter. This feature may be selected with or without the sound horn with lock feature selected. To make your selection, press and release the select button unt...

  • Page 340

    Key off power delay when this feature is selected, the power window switches, radio, hands–free system (if equipped), dvd video system (if equipped), power sunroof (if equipped), and power outlets will remain active for up to 10 minutes after the ignition switch is turned to the lock position. Openi...

  • Page 341

    Display fuel saver — if equipped the “eco” message is located in the compass / outside temperature / audio information / eco display. If display fuel saver is selected as on, only the eco message will display in the audio information / eco line of the display. If display fuel saver is selected as of...

  • Page 342

    Operating instructions - radio mode note: the ignition switch must be in the on or acc position to operate the radio. Power switch/volume control (rotary) push the on/volume control knob to turn on the radio. Press the on/volume control knob a second time to turn off the radio. Electronic volume con...

  • Page 343

    Voice command button uconnect® phone — if equipped press this button to operate the uconnect® phone feature (if equipped). Refer to “voice command” for further details. If your vehicle is not equipped with or this feature is not available on your vehicle, a “not equipped with uconnect phone” message...

  • Page 344

    The clock can also be set by pressing the setup button and selecting the “set home clock” entry. Once in this display follow the above procedure, starting at step 2. Info button press the info button for an rds station (one with call letters displayed). The radio will return a radio text message bro...

  • Page 345

    Push the rotary tune/scroll control knob a fifth time and fade will display. Turn the tune/scroll control knob to the left or right to adjust the sound level between the front and rear speakers. Push the rotary tune/scroll control knob again to exit setting tone, balance, and fade. Music type button...

  • Page 346

    Program type 16-digit character display oldies oldies personality persnlty public public rhythm and blues r & b religious music rel musc religious talk rel talk rock rock soft soft soft rock soft rck soft rhythm and blues soft r & b sports sports talk talk top 40 top 40 weather weather by pressing t...

  • Page 347

    • dvd enter - when the disc is in dvd menu mode, selecting dvd enter will allow you to play the current highlighted selection. Use the remote control to scroll up and down the menu (if equipped). • disc play/pause - you can toggle between playing the dvd and pausing the dvd by pushing the select but...

  • Page 348

    • set home clock - pressing the select button allows you to set the clock. Turn the tune/scroll control knob to adjust the hours and then press and turn the tune/scroll control knob to adjust the minutes. Press the tune/scroll control knob again to save changes. • player defaults - selecting this it...

  • Page 349

    Audio drc — if equipped selecting this item allows you to limit maximum audio dynamic range. The default is set to ⬙ high, ⬙ and under this setting, dialogues will play at 11 db higher than if the setting is ⬙ normal. ⬙ aspect ratio — if equipped selecting this item allows you to choose between wide...

  • Page 350

    You may add a second station to each pushbutton by repeating the above procedure with this exception: press the set button twice and set 2 will show in the display window. Each button can be set for set 1 and set 2 in both am and fm. This allows a total of 12 am, 12 fm, and 12 satellite (if equipped...

  • Page 351

    Note: the ignition switch must be in the on or acc position to operate the radio. Load button — loading compact disc(s) press the load button and the pushbutton with the corresponding number (1-6) where the cd is being loaded. The radio will display please wait and prompt when to insert disc. After ...

  • Page 352

    The current selection. Pressing and holding the seek button will allow you to scroll through the tracks faster in cd and mp3/mwa modes. Scan button (cd mode) press the scan button to scan through each track on the cd currently playing. Time button (cd mode) press this button to change the display fr...

  • Page 353

    The radio uses the following limits for file systems: • maximum number of directory levels: 8 • maximum number of files: 255 • maximum number of folders: 100 • maximum number of characters in file/folder names: • level 1: 12 (including a separator ⬙ . ⬙ and a three- character extension) • level 2: 3...

  • Page 354

    Mpeg specification sampling frequency (khz) bit rate (kbps) mpeg-1 audio layer 3 48, 44.1, 32 320, 256, 224, 192, 160, 128, 112, 96, 80, 64, 56, 48 mpeg-2 audio layer 3 24, 22.05, 16 160, 128, 144, 112, 96, 80, 64, 56, 48 wma specification sampling frequency (khz) bit rate (kbps) wma 44.1 and 48 48,...

  • Page 355

    To increase the speed of disc loading, it is recommended to use cd-r media and single-session discs. To create a single-session disc, enable the “disc at once” option before writing to the disc. List button (disc mode for mp3/wma play) pressing the list button will bring up a list of all folders on ...

  • Page 356

    Note: the aux device must be turned on and the device’s volume set to the proper level. If the aux audio is not loud enough, turn the device’s volume up. If the aux audio sounds distorted, turn the device’s volume down. Seek button (auxiliary mode) no function. Scan button (auxiliary mode) no functi...

  • Page 357

    Operating instructions - video entertainment system (ves™) (if equipped) refer to “video entertainment system (ves™)” for fur- ther details. Dolby® manufactured under license from dolby® laboratories. Dolby® and the double-d symbol are trademarks of dolby® laboratories. Macrovision this product inco...

  • Page 358

    Radio system in your vehicle. Sirius will supply a wel- come kit that contains general information, including how to setup your on-line listening account. For further information, call the toll-free number 888-539-7474, or visit the sirius web site at www.Sirius.Com, or at www.Siriuscanada.Ca for ca...

  • Page 359

    Satellite antenna to ensure optimum reception, do not place items on the roof around the rooftop antenna location. Metal objects placed within the line of sight of the antenna will cause decreased performance. Larger luggage items such as bikes should be placed as far rearward as possible, within th...

  • Page 360

    Scan button pressing the scan button causes the tuner to search for the next channel, pausing for eight seconds before con- tinuing to the next. To stop the search, press the scan button a second time. Info button pressing the info button will cycle the display informa- tion between artist, song tit...

  • Page 361

    Setup button pressing the setup button allows you to select the following items: • display sirius id number — press the audio/ select button to display the sirius id number. This number is used to activate, deactivate, or change the sirius subscription. Set button – to set the pushbutton memory when...

  • Page 362

    Uconnect® 730n/430/430n cd/dvd/hdd/ nav — if equipped refer to your uconnect® user’s manual for detailed operating instructions. Operating instructions (voice command system) — if equipped refer to “voice command” for further details. Operating instructions (uconnect® phone) — if equipped refer to “...

  • Page 363

    Power switch/volume control (rotary) push the on/volume control knob to turn on the radio. Push the on/volume control knob a second time to turn off the radio. Electronic volume control the electronic volume control turns continuously (360 de- grees) in either direction, without stopping. Turning th...

  • Page 364

    Rw/ff pressing the rw (rewind) or ff (fast forward) buttons causes the tuner to search for the next frequency in the direction of the arrows. This feature operates in either am or fm frequencies. Tune control turn the rotary tune/scroll control knob clockwise to increase or counterclockwise to decre...

  • Page 365

    Set/rnd button — to set the pushbutton memory when you are receiving a station that you wish to commit to pushbutton memory, press the set/rnd button. The sym- bol set 1 will now show in the display window. Select the button (1 to 6) you wish to lock onto this station and press and release that butt...

  • Page 366

    Inserting compact disc(s) gently insert one cd into the cd player with the cd label facing up. The cd will automatically be pulled into the cd player and the cd icon will illuminate on the radio display. If a cd does not go into the slot more than 1.0 in (2.5 cm), a disc may already be loaded and mu...

  • Page 367

    A disc can be ejected with the radio and ignition off. Note: ejecting with the ignition off is not allowed on convertible or soft-top models (if equipped). Seek button press the right seek button for the next selection on the cd. Press the left seek button to return to the beginning of the current s...

  • Page 368

    Notes on playing mp3 files the radio can play mp3 files; however, acceptable mp3 file recording media and formats are limited. When writing mp3 files, pay attention to the following restrictions. Supported media (disc types) the mp3 file recording media supported by the radio are cdda, cd-r, cd-rw, ...

  • Page 369

    Multisession disc formats are supported by the radio. Multisession discs may contain combinations of normal cd audio tracks and computer files (including mp3 files). Discs created with an option such as ⬙ keep disc open after writing ⬙ are most likely multisession discs. The use of multisession for ...

  • Page 370

    Playback of mp3 files when a medium containing mp3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the mp3 files. Loading times for playback of mp3 files may be affected by the following: • med...

  • Page 371

    Uconnect® 130 with satellite radio operating instructions — radio mode note: the ignition switch must be in the on or acc position to operate the radio. Power switch/volume control (rotary) push the on/volume control knob to turn on the radio. Push the on/volume control knob a second time to turn of...

  • Page 372

    Seek buttons press and release the seek buttons to search for the next listenable station in am/fm mode. Press the right switch to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection. Holding either button will bypass stations wit...

  • Page 373

    Clock setting procedure 1. Press and hold the time button until the hours blink. 2. Adjust the hours by turning the right side tune/ scroll control knob. 3. After adjusting the hours, press the right side tune/ scroll control knob to set the minutes. The minutes will begin to blink. 4. Adjust the mi...

  • Page 374

    Setting the tone, balance, and fade push the rotary tune/scroll control knob and bass will display. Turn the tune/scroll control knob to the right or left to increase or decrease the bass tones. Push the rotary tune/scroll control knob a second time and mid will display. Turn the tune/scroll control...

  • Page 375

    Toggle the music type button to select the following format types: program type 16-digit character display no program type or undefined none adult hits adlt hit classical classicl classic rock cls rock college college country country foreign language language information inform jazz jazz news news n...

  • Page 376

    By pressing the seek button when the music type icon is displayed, the radio will be tuned to the next frequency station with the same selected music type name. The music type function only operates when in the fm mode. If a preset button is activated while in the music type (program type) mode, the...

  • Page 377

    And 12 fm stations to be stored into pushbutton memory. The stations stored in set 2 memory can be selected by pressing the pushbutton twice. Every time a preset button is used, a corresponding button number will display. Buttons 1 - 6 these buttons tune the radio to the stations that you commit to ...

  • Page 378

    If you insert a disc with the ignition on and the radio on, the unit will switch from radio to cd mode and begin to play when you insert the disc. The display will show the track number, and index time in minutes and seconds. Play will begin at the start of track 1. Caution! • this cd player will ac...

  • Page 379

    Seek button press the right seek button for the next selection on the cd. Press the left seek button to return to the beginning of the current selection, or return to the beginning of the previous selection if the cd is within the first second of the current selection. Pressing and holding the seek ...

  • Page 380

    Supported media (disc types) the mp3 file recording media supported by the radio are cdda, cd-r, cd-rw, mp3, and cdda+mp3. Supported medium formats (file systems) the medium formats supported by the radio are iso 9660 level 1 and level 2 and includes the joliet extension. When reading discs recorded...

  • Page 381

    Supported mp3 file formats the radio will recognize only files with the *.Mp3 exten- sion as mp3 files. Non-mp3 files named with the *.Mp3 extension may cause playback problems. The radio is designed to recognize the file as an invalid mp3 and will not play the file. When using the mp3 encoder to co...

  • Page 382

    Playback of mp3 files when a medium containing mp3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the mp3 files. Loading times for playback of mp3 files may be affected by the following: • med...

  • Page 383

    Press and hold the info button again for three seconds to return to ⬙ elapsed time ⬙ display. Operation instructions - auxiliary mode the auxiliary (aux) jack is an audio input jack which allows the user to plug in a portable device such as an mp3 player or ipod® and utilize the vehicle’s audio syst...

  • Page 384

    System activation sirius satellite radio service is pre-activated, and you may begin listening immediately to the one year of audio service that is included with the factory-installed satellite radio system in your vehicle. Sirius will supply a welcome kit that contains general information, includin...

  • Page 385

    Satellite antenna to ensure optimum reception, do not place items on the roof around the rooftop antenna location. Metal objects placed within the line of sight of the antenna will cause decreased performance. Larger luggage items such as bikes should be placed as far rearward as possible, within th...

  • Page 386

    Scan button pressing the scan button causes the tuner to search for the next channel, pausing for eight seconds before con- tinuing to the next. To stop the search, press the scan button a second time. Info button pressing the info button will cycle the display informa- tion between artist, song tit...

  • Page 387

    Setup button pressing the setup button allows you to select the following items: • display sirius id number — press the audio/ select button to display the sirius id number. This number is used to activate, deactivate, or change the sirius subscription. Set button – to set the pushbutton memory when...

  • Page 388

    Ipod®/usb/mp3 control — if equipped this feature allows an ipod® or external usb device to be plugged into the usb port, located in the center console. Ipod® control supports mini, 4g, photo, nano, 5g ipod® and iphone® devices. Some ipod® software versions may not fully support the ipod® control fea...

  • Page 389

    Once the audio device is connected and synchronized to the vehicles ipod®/usb/mp3 control system (ipod® or external usb device may take a few minutes to connect), the audio device starts charging and is ready for use by pressing radio switches, as described below. Note: if the audio device battery i...

  • Page 390

    Play mode when switched to ipod®/usb/mp3 control mode, the ipod® or external usb device automatically starts play mode. In play mode, the following buttons on the radio faceplate may be used to control the ipod® or external usb device and display data: • use the tune control knob to select the next ...

  • Page 391

    • pressing the repeat button will change the audio device mode to repeat the current playing track or press the vr button and say ⬙ repeat on ⬙ or ⬙ repeat off ⬙ . • press the scan button to use ipod®/usb/mp3 de- vice scan mode, which will play the first 10 seconds of each track in the current list ...

  • Page 392

    • during all list modes, the ipod® displays all lists in “wrap-around” mode. So if the track is at the bottom of the list, just turn the wheel backward (counter- clockwise) to get to the track faster. • in list mode, the radio preset buttons are used as shortcuts to the following lists on the ipod® ...

  • Page 393

    Caution! • leaving the ipod® or external usb device (or any supported device) anywhere in the vehicle in ex- treme heat or cold can alter the operation or dam- age the device. Follow the device manufacturer’s guidelines. • placing items on the ipod® or external usb device, or connections to the ipod...

  • Page 394

    Selecting a different audio device 1. Press the phone button to begin. 2. After the ⬙ ready ⬙ prompt and following the beep, say ⬙ setup ⬙ , then say ⬙ select audio devices ⬙ . 3. Say the name of the audio device or ask the uconnect® phone system to list the audio devices. Next track use the seek up...

  • Page 395

    The right-hand control is a rocker-type switch with a pushbutton in the center and controls the volume and mode of the sound system. Pressing the top of the rocker switch will increase the volume, and pressing the bottom of the rocker switch will decrease the volume. Pressing the center button will ...

  • Page 396

    Cd player pressing the top of the switch once will go to the next track on the cd. Pressing the bottom of the switch once will go to the beginning of the current track, or to the beginning of the previous track if it is within one second after the current track begins to play. If you press the switc...

  • Page 397

    Note: if you experience difficulty in playing a particular disc, it may be damaged (i.E., scratched, reflective coating removed, a hair, moisture or dew on the disc) oversized, or have protection encoding. Try a known good disc before considering disc player service. Radio operation and mobile phone...

  • Page 398

    Blower control rotate this control to regulate the amount of air forced through the ven- tilation system in any mode. The blower speed increases as you move the control to the right from the “o” (off) position. There are seven blower speeds. Note: for vehicles equipped with remote start, the climate...

  • Page 399

    Mode control (air direction) rotate this control to choose from sev- eral patterns of air distribution. You can select either a primary mode as identified by the symbols on the con- trol, or a blend of two of these modes. The closer the setting is to a particular symbol, the more air distribution yo...

  • Page 400

    Defrost air is directed through the windshield and side window demist outlets. Use this mode with maxi- mum blower and temperature settings for best wind- shield and side window defrosting. Note: the air conditioning compressor operates in mix, defrost, or a blend of these modes, even if the air con...

  • Page 401

    Air conditioning control press this button to engage the air con- ditioning. A light will illuminate when the air conditioning system is engaged. Rotating the dial left into the blue area of the scale indicates cooler temperatures, while rotating right into the red area indicates warmer temperatures...

  • Page 402

    Operation of the system is quite simple. 1. Turn the mode control knob (on the right) and the blower control knob (on the left) to auto. Note: the auto position performs best for front seat occupants only. Dial in the temperature you would like the system to maintain by rotating the temperature cont...

  • Page 403

    Blower control for full automatic operation or for automatic blower operation, turn the knob to the auto position. In manual mode, there are seven blower speeds that can be individually selected. In off position, the blower will shut off. Manual operation this system offers a full complement of manu...

  • Page 404

    402 understanding your instrument panel.

  • Page 405

    The operator can override the auto mode setting to change airflow distribution by rotating the mode control knob (on the right) to one of the following positions. • panel air is directed through the outlets in the instrument panel. These outlets can be adjusted to direct airflow. Note: the center in...

  • Page 406

    • air conditioner control press this button to turn on the air conditioning during manual operation only. When the air conditioning is turned on, cool dehumidified air will flow through the outlets selected with the mode control dial. Press this but- ton a second time to turn off the air conditionin...

  • Page 407

    • most of the time, when in automatic operation, you can temporarily put the system into recirculation mode by pressing the recirculation button. However, under certain conditions, while in automatic mode, the system is blowing air out the defrost vents. When these conditions are present, and the re...

  • Page 408

    Winter operation use of the air recirculation mode during winter months is not recommended because it may cause window fogging. Vacation storage anytime you store your vehicle, or keep it out of service (i.E., vacation) for two weeks or more, run the air conditioning system at idle for about five mi...

  • Page 409

    Side window demisters a side window demister outlet is located at each end of the instrument panel. These non-adjustable outlets direct air toward the side windows when the system is in the floor, mix, or defrost mode. The air is directed at the area of the windows through which you view the outside...

  • Page 410

    Control setting suggestions for various weather conditions 408 understanding your instrument panel.

  • Page 411: Starting And Operating

    Starting and operating contents 䡵 starting procedures . . . . . . . . . . . . . . . .414 ▫ manual transmission – if equipped . . . . . . . .414 ▫ automatic transmission – if equipped . . . . . .415 ▫ normal starting. . . . . . . . . . . . . . . . . . . . . . .415 ▫ extreme cold weather (below –20°f ...

  • Page 412

    䡵 four–wheel drive operation (command-trac i® or rock-trac®) . . . .433 ▫ operating instructions/precautions . . . . . . . .433 ▫ shift positions . . . . . . . . . . . . . . . . . . . . . . . .435 ▫ shifting procedure . . . . . . . . . . . . . . . . . . . . .436 䡵 trac-lok® rear axle — if equipped ....

  • Page 413

    ▫ traction control system (tcs) . . . . . . . . . . . .461 ▫ brake assist system (bas) . . . . . . . . . . . . . . .462 ▫ hill start assist (hsa) . . . . . . . . . . . . . . . . .463 ▫ electronic roll mitigation (erm) . . . . . . . . . .466 ▫ electronic stability control (esc) . . . . . . . . . .467...

  • Page 414

    ▫ compact spare tire – if equipped . . . . . . . . .493 ▫ full size spare – if equipped . . . . . . . . . . . . .494 ▫ limited-use spare – if equipped . . . . . . . . . .494 ▫ tire spinning . . . . . . . . . . . . . . . . . . . . . . . .495 ▫ tread wear indicators . . . . . . . . . . . . . . . . . ....

  • Page 415

    䡵 vehicle loading . . . . . . . . . . . . . . . . . . . .519 ▫ certification label . . . . . . . . . . . . . . . . . . . .519 䡵 trailer towing . . . . . . . . . . . . . . . . . . . . .522 ▫ common towing definitions . . . . . . . . . . . . .522 ▫ trailer hitch classification . . . . . . . . . . . . ...

  • Page 416

    Starting procedures before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. Warning! • when leaving the vehicle, always remove the key fob from the ignition and lock your vehicle. • never leave children alone in a vehicle, or with access to...

  • Page 417

    Four-wheel drive models only in 4l mode, this vehicle will start regardless of whether or not the clutch pedal is pressed to the floor. This feature enhances off-road performance by allowing the vehicle to start when in 4l without having to press the clutch pedal. The “4wd indicator light” will illu...

  • Page 418

    Extreme cold weather (below –20°f or −29°c) to ensure reliable starting at these temperatures, use of an externally powered electric engine block heater (avail- able from your authorized dealer) is recommended. If engine fails to start warning! • never pour fuel or other flammable liquids into the t...

  • Page 419

    Caution! To prevent damage to the starter, do not crank the engine for more than 15 seconds at a time. Wait 10 to 15 seconds before trying again. If the engine has been flooded, it may start to run, but not have enough power to continue running when the key is released. If this occurs, continue cran...

  • Page 420

    After starting the idle speed is controlled automatically and it will decrease as the engine warms up. Engine block heater — if equipped the engine block heater warms the engine, and permits quicker starts in cold weather. Connect the cord to a standard 110-115 volt ac electrical outlet with a groun...

  • Page 421

    Shifting fully press the clutch pedal before shifting gears. As you release the clutch pedal, lightly press the accelerator pedal. You should always use first gear when starting from a standing position. Recommended vehicle shift speeds to utilize your manual transmission efficiently for both fuel e...

  • Page 422

    Manual transmission shift speeds in mph (km/h) engine speeds 1 to 2 2 to 3 3 to 4 4 to 5 5 to 6 3.6l accel. 15 (24) 24 (39) 34 (55) 47 (76) 56 (90) cruise 10 (16) 19 (31) 27 (43) 37 (60) 41 (66) note: vehicle speeds shown in the chart above are for 2h and 4h only, vehicle speeds in 4l would be signi...

  • Page 423

    Caution! When descending a hill, be very careful to downshift one gear at a time to prevent overspeeding the engine which can cause valve damage, and/or clutch disc damage, even if the clutch pedal is pressed. Maximum recommended downshift speeds caution! Failure to follow the maximum recommended do...

  • Page 424

    Reverse shifting to shift into reverse, bring the vehicle to a complete stop. Press the clutch and pause briefly to allow the gear train to stop rotating. Beginning from the neutral position, move the shift lever in one quick, smooth motion straight across and into the reverse area (the driver will ...

  • Page 425

    Warning! • unintended movement of a vehicle could injure those in or near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, always apply the parking brake, shift the transmission into park, and remove the ignition key. Once the ...

  • Page 426

    Warning! (continued) • it is dangerous to shift out of park or neutral if the engine speed is higher than idle speed. If your foot is not firmly pressing the brake pedal, the vehicle could accelerate quickly forward or in re- verse. You could lose control of the vehicle and hit someone or something....

  • Page 427

    The electronically-controlled transmission provides a precise shift schedule. The transmission electronics are self-calibrating; therefore, the first few shifts on a new vehicle may be somewhat abrupt. This is a normal condition, and precision shifts will develop within a few hundred miles (kilomete...

  • Page 428

    Gear ranges do not race the engine when shifting from park or neutral into another gear range. Note: • after selecting any gear range, wait a moment to allow the selected gear to engage before accelerating. This is especially important when the engine is cold. • if there is a need to restart the eng...

  • Page 429

    Warning! • never use the park position as a substitute for the parking brake. Always apply the parking brake fully when parked to guard against vehicle movement and possible injury or damage. • your vehicle could move and injure you and others if it is not completely in park. Check by trying to move...

  • Page 430

    Warning! (continued) warned not to touch the parking brake, brake pedal or the shift lever. • do not leave the key fob in or near the vehicle, or in a location accessible to children. A child could operate power windows, other controls, or move the vehicle. Caution! • before moving the shift lever o...

  • Page 431

    Neutral use this range when the vehicle is standing for prolonged periods with the engine running. The engine may be started in this range. Apply the parking brake and shift the transmission into park if you must leave the vehicle. Warning! Do not coast in neutral and never turn off the ignition to ...

  • Page 432

    When frequent transmission shifting occurs (such as when operating the vehicle under heavy loading condi- tions, in hilly terrain, traveling into strong head winds, or while towing heavy trailers), use the autostick® shift control (refer to “autostick®” in this section) to select a lower gear. Under...

  • Page 433

    Note: even if the transmission can be reset, we recom- mend that you visit your authorized dealer at your earliest possible convenience. Your authorized dealer has diagnostic equipment to determine if the problem could recur. If the transmission cannot be reset, authorized dealer service is required...

  • Page 434

    Warning! Do not downshift for additional engine braking on a slippery surface. The drive wheels could lose their grip and the vehicle could skid, causing a collision or personal injury. Screen display 1 2 3 4 d actual gear(s) allowed 1 1-2 1-3 1-4 1-5 note: to select the proper gear position for max...

  • Page 435

    Four–wheel drive operation (command-trac i® or rock-trac®) warning! Failure to engage a position completely can cause transfer case damage or loss of power and vehicle control. You could have a collision. Do not drive the vehicle unless the transfer case is fully engaged. Operating instructions/prec...

  • Page 436

    In the event that additional traction is required, the transfer case 4h and 4l positions can be used to lock the front and rear driveshafts together, forcing the front and rear wheels to rotate at the same speed. This is accom- plished by simply moving the shift lever to one of these positions. The ...

  • Page 437

    Warning! You or others could be injured if you leave the vehicle unattended with the transfer case in the neutral (n) position without first fully engaging the parking brake. The transfer case neutral (n) position disengages both the front and rear drive- shaft from the powertrain, and will allow th...

  • Page 438

    4l position this range locks the front and rear driveshafts together, forcing the front and rear wheels to rotate at the same speed. This range (4l) provides additional traction and maximum pulling power for loose, slippery road surfaces only. Do not exceed 25 mph (40 km/h). The “4wd indicator light...

  • Page 439

    Note: shifting into or out of 4l is possible with the vehicle completely stopped; however, difficulty may oc- cur due to the mating teeth not being properly aligned. Several attempts may be required for clutch teeth align- ment and shift completion to occur. The preferred method is with the vehicle ...

  • Page 440

    Axle lock (tru–lok®) — rubicon models the axle lock switch is located on the instrument panel (to the left of the steering column). This feature will only activate when the following con- ditions are met: • key in ignition, vehicle in 4l (low) range. • vehicle speed should be 10 mph (16 km/h) or les...

  • Page 441

    To unlock the axles, press the top of the axle lock switch. Axle lock will disengage if the vehicle is taken out of 4l (low) range, or the ignition switch is turned to the off position. Electronic sway bar disconnect — if equipped your vehicle may be equipped with an electronic discon- necting stabi...

  • Page 442

    Indicator light” will flash during activation transition, or when activation conditions are not met. The stabilizer/ sway bar should remain in on-road mode during normal driving conditions. Warning! Do not disconnect the stabilizer bar and drive on hard-surfaced roads or at speeds above 18 mph (29 k...

  • Page 443

    Warning! If the stabilizer/sway bar will not return to on-road mode, vehicle stability is greatly reduced. Do not attempt to drive the vehicle over 18 mph (29 km/h). Driving faster than 18 mph (29 km/h) may cause loss of control of the vehicle, which could result in serious injury. Contact your loca...

  • Page 444

    Off-road driving tips side step removal – if equipped note: prior to off-road usage, the side steps should be removed to prevent damage. 1. Remove the two nuts from the bodyside. 2. Remove one bolt from the underside of the vehicle. 3. Remove the side step assembly. 442 starting and operating.

  • Page 445

    The basics of off-road driving you will encounter many types of terrain driving off- road. You should be familiar with the terrain and area before proceeding. There are many types of surface conditions: hard-packed dirt, gravel, rocks, grass, sand, mud, snow and ice. Every surface has a different ef...

  • Page 446

    Extreme situations such as deep snow, mud, steep in- clines, or sand where additional low speed pulling power is needed. Vehicle speeds in excess of 25 mph (40 km/h) should be avoided when in 4l (low) range. Caution! Do not use 4l (low) range when operating the vehicle on dry pavement. Driveline har...

  • Page 447

    Mud deep mud creates a great deal of suction around the tires and is very difficult to get through. You should use second gear (manual transmission), or drive (automatic transmission), with the transfer case in the 4l (low) position to maintain your momentum. If you start to slow to a stop, try turn...

  • Page 448

    Crossing obstacles (rocks and other high points) while driving off-road, you will encounter many types of terrain. These varying types of terrain bring different types of obstacles. Before proceeding, review the path ahead to determine the correct approach and your ability to safely recover the vehi...

  • Page 449

    Caution! • never attempt to straddle a rock that is large enough to strike your axles or undercarriage. • never attempt to drive over a rock which is large enough to contact the door sills. Crossing a ravine, gully, ditch, washout or rut when crossing a ravine, gully, ditch, washout or a large rut, ...

  • Page 450

    Caution! Do not attempt to cross a log with a greater diameter than the running ground clearance or the vehicle will become high-centered. Getting high-centered if you get hung up or high-centered on an object, get out of the vehicle and try to determine what the vehicle is hung up on, where it is c...

  • Page 451

    Driving up hill once you have determined your ability to proceed and have shifted into the appropriate gear, line your vehicle up for the straightest possible run. Accelerate with an easy constant throttle and apply more power as you start up the hill. Do not race forward into a steep grade; the abr...

  • Page 452

    Warning! Do not descend a steep grade in neutral. Use vehicle brakes in conjunction with engine braking. Descending a grade too fast could cause you to lose control and be seriously injured or killed. Driving across an incline if at all possible, avoid driving across an incline. If it is necessary, ...

  • Page 453

    Driving through water extreme care should be taken crossing any type of water. Water crossings should be avoided, if possible, and only be attempted when necessary in a safe, responsible manner. You should only drive through areas which are designated and approved. You should tread lightly and avoid...

  • Page 454

    Before you cross any type of water as you approach any type of water, you need to determine if you can cross it safely and responsibly. If necessary, get out and walk through the water or probe it with a stick. You need to be sure of its depth, approach angle, current and bottom condition. Be carefu...

  • Page 455

    Crossing ditches, streams, shallow rivers or other flowing water flowing water can be extremely dangerous. Never attempt to cross a fast running stream or river even in shallow water. Fast moving water can easily push your vehicle down- stream, sweeping it out of control. Even in very shallow water,...

  • Page 456

    • check threaded fasteners for looseness, particularly on the chassis, drivetrain components, steering, and sus- pension. Retighten them, if required, and torque to the values specified in the service manual. • check for accumulations of plants or brush. These things could be a fire hazard. They mig...

  • Page 457

    Power steering the standard power steering system will give you good vehicle response and increased ease of maneuverability in tight spaces. The system will provide mechanical steering capability if power assist is lost. If for some reason the power assist is interrupted, it will still be possible t...

  • Page 458

    Power steering fluid check checking the power steering fluid level at a defined service interval is not required. The fluid should only be checked if a leak is suspected, abnormal noises are apparent, and/or the system is not functioning as antici- pated. Coordinate inspection efforts through an aut...

  • Page 459

    The parking brake lever is located in the center console. To apply the parking brake, pull the lever up as firmly as possible. To release the parking brake, pull the lever up slightly, press the center button, then lower the lever completely. When the parking brake is applied with the ignition switc...

  • Page 460

    Difficult to move the shift lever out of park. The parking brake should always be applied whenever the driver is not in the vehicle. Warning! • never use the park position on an automatic transmission as a substitute for the parking brake. Always apply the parking brake fully when parked to guard ag...

  • Page 461

    Caution! If the “brake warning light” remains on with the parking brake released, a brake system malfunction is indicated. Have the brake system serviced by an authorized dealer immediately. Anti-lock brake system the anti-lock brake system (abs) is designed to aid the driver in maintaining vehicle ...

  • Page 462

    Warning! • pumping of the anti-lock brakes will diminish their effectiveness and may lead to a collision. Pumping makes the stopping distance longer. Just press firmly on your brake pedal when you need to slow down or stop. • the anti-lock brake system (abs) cannot prevent the natural laws of physic...

  • Page 463

    Trailer sway control (tsc), and hill descent control (hdc). All of these systems work together to enhance vehicle stability and control in various driving condi- tions, and are commonly referred to as esc. Warning! The anti-lock brake system (abs) cannot prevent the natural laws of physics from acti...

  • Page 464

    Brake assist system (bas) the bas is designed to optimize the vehicle’s braking capability during emergency braking maneuvers. The system detects an emergency braking situation by sens- ing the rate and amount of brake application and then applies optimum pressure to the brakes. This can help reduce...

  • Page 465

    Hill start assist (hsa) the hsa system is designed to assist the driver when starting a vehicle from a stop on a hill. Hsa will maintain the level of brake pressure the driver applied for a short period of time after the driver takes their foot off of the brake pedal. If the driver does not apply th...

  • Page 466

    Warning! There may be situations on minor hills (i.E., less than 8%), with a loaded vehicle, or while pulling a trailer where the system will not activate and slight rolling may occur, which could cause a collision with an- other vehicle or object. Always remember the driver is responsible for braki...

  • Page 467

    Towing with hsa hsa will provide assistance when starting on a grade when pulling a trailer. Warning! • if you use a trailer brake controller with your trailer, your trailer brakes may be activated and deactivated with the brake switch. If so, when the brake pedal is released there may not be enough...

  • Page 468

    Hsa off if you wish to turn off the hsa system, follow this procedure: 1. Start with the engine off and vehicle in park (automatic transmission) or neutral with clutch out (manual transmission) with wheels straight. Apply parking brake on manual transmission vehicle. 2. Start the engine. 3. With the...

  • Page 469

    Electronic roll mitigation (erm) can only reduce the chance of wheel lift occurring during severe or evasive driving maneuvers. It cannot prevent wheel lift due to other factors such as road conditions, leaving the road- way or striking objects or other vehicles. Note: anytime the esc system is in t...

  • Page 470

    Esc uses sensors in the vehicle to determine the vehicle path intended by the driver and compares it to the actual path of the vehicle. When the actual path does not match the intended path, esc applies the brake of the appro- priate wheel to assist in counteracting the oversteer or understeer condi...

  • Page 471

    The esc system has three available operating modes in 4h range. The system has one operating mode in 4l range. Two-wheel drive vehicles and four-wheel drive vehicles in 2h range have two operating modes. 4h range (4wd models) on this is the normal operating mode for esc in 4h range. Partial off this...

  • Page 472

    All other stability features of esc function normally. This mode is intended to be used if the vehicle is in deep snow, sand, or gravel conditions and more wheel spin than esc would normally allow is required to gain traction. To turn esc on again, momentarily press the esc off switch. This will res...

  • Page 473

    4l range (4wd models) esc off this is the normal operating mode for esc in 4l range. Whenever the vehicle is started in 4l range, or the transfer case (if equipped) is shifted from 4h range or neutral to 4l range, the esc system will be in this mode. In 4l range, esc and tcs, except for the “limited...

  • Page 474

    Partial off when in “partial off” mode, the tcs portion of esc has been disabled and the “esc activation/malfunction indicator light” will be illuminated. All other stability features of esc function normally. This mode is intended to be used if the vehicle is in deep snow, sand, or gravel condition...

  • Page 475

    Malfunction indicator light” begins to flash during ac- celeration, ease up on the accelerator and apply as little throttle as possible. Be sure to adapt your speed and driving to the prevailing road conditions. Note: • each time the ignition is cycled on, the esc system will be on even if it was cy...

  • Page 476

    Warning! If tsc activates while driving, slow the vehicle down, stop at the nearest safe location, and adjust the trailer load to eliminate trailer sway. Hill descent control (hdc) – if equipped hdc is only intended for low speed off-road driving. Hdc maintains vehicle speed while descending hills i...

  • Page 477

    However, the driver can override hdc operation by applying the brake to slow the vehicle down below the hdc control speed. If more speed is desired during hdc control, the accelerator pedal will increase vehicle speed in the usual manner. When either the brake or the accelerator is released, hdc wil...

  • Page 478

    Tire safety information tire markings note: • p (passenger) - metric tire sizing is based on u.S. Design standards. P-metric tires have the letter “p” molded into the sidewall preceding the size designa- tion. Example: p215/65r15 95h. • european-metric tire sizing is based on european design standar...

  • Page 479

    • temporary spare tires are spares designed for tempo- rary emergency use only. Temporary high pressure compact spare tires have the letter “t” or “s” molded into the sidewall preceding the size designation. Ex- ample: t145/80d18 103m. • high flotation tire sizing is based on u.S. Design standards a...

  • Page 480

    Example: r = construction code — ⬙ r ⬙ means radial construction — ⬙ d ⬙ means diagonal or bias construction 15 = rim diameter in inches (in) service description: 95 = load index — a numerical code associated with the maximum load a tire can carry h = speed symbol — a symbol indicating the range of ...

  • Page 481

    Example: load identification: ⴖ ....Blank.... ⴖ = absence of any text on the sidewall of the tire indicates a standard load (sl) tire extra load (xl) = extra load (or reinforced) tire light load (ll) = light load tire c, d, e, f, g = load range associated with the maximum load a tire can carry at a ...

  • Page 482

    Example: dot ma l9 abcd 0301 dot = department of transportation — this symbol certifies that the tire is in compliance with the u.S. Department of transportation tire safety standards and is approved for highway use ma = code representing the tire manufacturing location (two digits) l9 = code repres...

  • Page 483

    Tire terminology and definitions term definition b-pillar the vehicle b-pillar is the structural member of the body located behind the front door. Cold tire inflation pressure cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least 3 hours, or ...

  • Page 484

    Tire loading and tire pressure tire placard location tire placard location (two-door model) tire placard location (four-door model) 482 starting and operating.

  • Page 485

    Tire and loading information placard this placard tells you important information about the: 1) number of people that can be carried in the vehicle 2) total weight your vehicle can carry 3) tire size designed for your vehicle 4) cold tire inflation pressures for the front, rear, and spare tires. Loa...

  • Page 486

    Note: under a maximum loaded vehicle condition, gross axle weight ratings (gawrs) for the front and rear axles must not be exceeded. For further information on gawrs, vehicle loading, and trailer towing, refer to “vehicle loading” in this section. To determine the maximum loading conditions of your ...

  • Page 487

    4. The resulting figure equals the available amount of cargo and luggage load capacity. For example, if “xxx” amount equals 1,400 lbs (635 kg) and there will be five 150 lb (68 kg) passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lbs (295 kg) (since 5 x 150 ...

  • Page 488

    486 starting and operating.

  • Page 489

    Warning! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. Tires — general information tire pressure proper tire inflation pressur...

  • Page 490

    Warning! (continued) • unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left. • always drive with each tire inflated to the recom- mended cold tire inflation pressure. Economy improper inflation pressures can cause uneven wear pat- terns...

  • Page 491

    Tire inflation pressures tire pressure should be checked and adjusted as well as inspected for signs of tire wear or visible damage, at least once a month. Use a good quality pocket-type gauge to check tire pressure. Do not make a visual judgement when determining proper inflation. Radial tires may ...

  • Page 492

    Example: if garage temperature = 68° f (20° c) and the outside temperature = 32° f (0° c) then the cold tire inflation pressure should be increased by 3 psi (21 kpa), which equals 1 psi (7 kpa) for every 12° f (7° c) for this outside temperature condition. Tire pressure may increase from 2 to 6 psi ...

  • Page 493

    Radial ply tires warning! Combining radial ply tires with other types of tires on your vehicle will cause your vehicle to handle poorly. The instability could cause a collision. Al- ways use radial ply tires in sets of four. Never combine them with other types of tires. Tire repair if your tire beco...

  • Page 494

    Summer or three season tires – if equipped summer tires provide traction in both wet and dry conditions, and are not intended to be driven in snow or on ice. Summer tires will not contain the all season designation or mountain/snowflake symbol on the tire sidewall. Use summer tires only in sets of f...

  • Page 495

    Spare tire matching original equipped tire and wheel – if equipped your vehicle may be equipped with a spare tire and wheel equivalent in look and function to the original equipment tire and wheel found on the front or rear axle of your vehicle. This spare tire may be used in the tire rotation for y...

  • Page 496

    Warning! (continued) replaced. Be sure to follow the warnings, which apply to your spare. Failure to do so could result in spare tire failure and loss of vehicle control. Full size spare – if equipped the full size spare is for temporary emergency use only. This tire may look like the originally equ...

  • Page 497

    Warning! (continued) inflated to the cold tire inflation pressures listed on your tire and loading information placard located on the driver’s side b-pillar or the rear edge of the driver’s side door. Replace (or repair) the original equipment tire at the first opportunity and reinstall it on your v...

  • Page 498

    Tread wear indicators tread wear indicators are in the original equipment tires to help you in determining when your tires should be replaced. These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth becomes 1/16 in (2 mm). When the tread is wo...

  • Page 499

    Warning! Tires and the spare tire should be replaced after six years, regardless of the remaining tread. Failure to follow this warning can result in sudden tire failure. You could lose control and have a collision resulting in serious injury or death. Keep dismounted tires in a cool, dry place with...

  • Page 500

    Warning! • do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change sus- pension dimensions and performance characteris- tics, resulting in changes to steering, handling, and braking of your vehicle. This can caus...

  • Page 501

    Tire chains (traction devices) use of traction devices require sufficient tire-to-body clearance. Follow these recommendations to guard against damage. • traction device must be of proper size for the tire, as recommended by the traction device manufacturer. • install on rear tires only. • p225/75r1...

  • Page 502

    Caution! (continued) • observe the traction device manufacturer’s instruc- tions on the method of installation, operating speed, and conditions for use. Always use the suggested operating speed of the device manufac- turer’s if it is less than 30 mph (48 km/h). • do not use traction devices on a com...

  • Page 503

    The suggested rotation method is the “forward-cross” shown in the following diagram. Caution! Proper operation of four-wheel drive vehicles de- pends on tires of equal size, type and circumference on each wheel. Any difference in tire size can cause damage to the transfer case. Tire rotation schedul...

  • Page 504

    On cold inflation tire pressure. This is defined as the tire pressure after a vehicle has not been driven for more than three hours, or driven less than 1 mile (1.6 km) after a three-hour period. Refer to “tires – general informa- tion” in “starting and operating” for information on how to properly ...

  • Page 505

    For example, your vehicle may have a recommended cold (parked for more than three hours) air pressure of 35 psi (241 kpa). If the ambient temperature is 68°f (20°c) and the measured tire pressure is 30 psi (207 kpa), a temperature drop to 20°f (-7°c) will decrease the tire pressure to approximately ...

  • Page 506

    Note: • the tpms is not intended to replace normal tire care and maintenance, nor to provide warning of a tire failure or condition. • the tpms should not be used as a tire pressure gauge while adjusting your tire pressure. • driving on a significantly under-inflated tire causes the tire to overheat...

  • Page 507

    The tire pressure monitor system (tpms) consists of the following components: • receiver module • four tire pressure monitoring sensors • tire pressure monitoring telltale light a tire pressure monitoring sensor is located in the spare wheel if the vehicle is equipped with a matching full size spare...

  • Page 508

    The “tire pressure monitoring telltale light” will flash on and off for 75 seconds, and will remain on solid when a system fault is detected. The system fault will also sound a chime. If the ignition key is cycled, this sequence will repeat, providing the system fault still exists. A system fault ca...

  • Page 509

    Note: • if your vehicle is equipped with a matching full-size spare wheel and tire assembly, it has a tire pressure monitoring sensor, and can be monitored by the tire pressure monitoring system (tpms). In the event that the matching full-size spare tire is swapped with a low pressure road tire, the...

  • Page 510

    Premium system – if equipped the tire pressure monitor system (tpms) uses wireless technology with wheel rim-mounted electronic sensors to monitor tire pressure levels. Sensors, mounted to each wheel as part of the valve stem, transmit tire pressure readings to the receiver module. Note: it is parti...

  • Page 511

    Should a low tire condition occur on any of the four active road tire(s), you should stop as soon as possible, and inflate the low tire(s) that is “flashing” on the graphic display to the vehicle’s recommended cold tire pressure inflation value shown in the “inflate to xx” message. The system will a...

  • Page 512

    Note: your system can be set to display pressure units in psi, kpa, or bar. If the ignition switch is cycled, this sequence will repeat, providing the system fault still exists. If the system fault no longer exists, the “tire pressure monitoring telltale light” will no longer flash, the ⬙ service tp...

  • Page 513

    Message is then followed by a graphic display, with pressure values still shown. This indicates the pressure values are still being received from the tpm sensors but they may not be located in the correct vehicle position. However, the system still needs to be serviced as long as the ⬙ service tpm s...

  • Page 514

    For each subsequent ignition switch cycle, a chime will sound, the “tire pressure monitoring telltale light” will flash on and off for 75 seconds and then remain on solid, and the evic will display a ⬙ service tpm system ⬙ message for a minimum of five seconds and then display dashes (- -) in place ...

  • Page 515

    Fuel requirements 3.6l engine this engine is designed to meet all emis- sions regulations and provide excellent fuel economy and performance when using high-quality unleaded “regular” gasoline having an octane rating of 87. The use of premium gasoline is not recommended, as it will not provide any b...

  • Page 516

    Gasoline/oxygenate blends some fuel suppliers blend unleaded gasoline with oxy- genates such as ethanol. Fuels blended with oxygenates may be used in your vehicle. Caution! Do not use gasoline containing methanol or gaso- line containing more than 10% ethanol. Use of these blends may result in start...

  • Page 517

    To fix a non-ffv vehicle inadvertently fueled once with e-85 perform the following: • drain the fuel tank (see your authorized dealer) • change the engine oil and oil filter • disconnect and reconnect the battery to reset the engine controller memory more extensive repairs will be required for prolo...

  • Page 518

    Fuel system cautions caution! Follow these guidelines to maintain your vehicle’s performance: • the use of leaded gas is prohibited by federal law. Using leaded gasoline can impair engine perfor- mance and damage the emissions control system. • an out-of-tune engine or certain fuel or ignition malfu...

  • Page 519

    Carbon monoxide warnings warning! Carbon monoxide (co) in exhaust gases is deadly. Follow the precautions below to prevent carbon monoxide poisoning: • do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas, which can kill. Never run the engine in a closed area, such...

  • Page 520

    Caution! • damage to the fuel system or emission control system could result from using an improper fuel cap (gas cap). A poorly fitting cap could let impu- rities into the fuel system. Also, a poorly fitting aftermarket cap can cause the “malfunction indi- cator light (mil)” to illuminate, due to f...

  • Page 521

    • if the gas cap is not tightened properly, the mil will come on. Be sure the gas cap is tightened every time the vehicle is refueled. Loose fuel filler cap message after fuel has been added, the vehicle diagnostic system can determine if the fuel filler cap is possibly loose, improperly installed, ...

  • Page 522

    Gross vehicle weight rating (gvwr) the gvwr is the total permissible weight of your vehicle including driver, passengers, vehicle, options and cargo. The label also specifies maximum capacities of front and rear axle systems (gawr). Total load must be limited so gvwr and front and rear gawr are not ...

  • Page 523

    Inflation pressure this is the cold tire inflation pressure for your vehicle for all loading conditions up to full gawr. Curb weight the curb weight of a vehicle is defined as the total weight of the vehicle with all fluids, including vehicle fuel, at full capacity conditions, and with no occupants ...

  • Page 524

    Caution! Do not load your vehicle any heavier than the gvwr or the maximum front and rear gawr. If you do, parts on your vehicle can break, or it can change the way your vehicle handles. This could cause you to lose control. Also overloading can shorten the life of your vehicle. Trailer towing in th...

  • Page 525

    Gross combination weight rating (gcwr) the gcwr is the total permissible weight of your vehicle and trailer when weighed in combination. Note: the gcwr rating includes a 150 lbs (68 kg) allowance for the presence of a driver. Gross axle weight rating (gawr) the gawr is the maximum capacity of the fr...

  • Page 526

    Trailer sway control – if equipped the trailer sway control is a telescoping link that can be installed between the hitch receiver and the trailer tongue. It typically provides adjustable friction associ- ated with the telescoping motion to dampen any un- wanted trailer swaying motions while traveli...

  • Page 527

    Warning! • an improperly adjusted weight distributing hitch system may reduce handling, stability, braking performance, and could result in a collision. • weight distributing systems may not be compatible with surge brake couplers. Consult with your hitch and trailer manufacturer or a reputable recr...

  • Page 528

    Trailer towing weights (maximum trailer weight ratings) the following chart provides the maximum trailer weight ratings towable for your given drivetrain. Engine/ transmission axle model gcwr (gross combined wt. Rating) frontal area max. Gtw (gross trailer wt.) max. Trailer tongue wt. (see note) 3.6...

  • Page 529

    Engine/ transmission axle model gcwr (gross combined wt. Rating) frontal area max. Gtw (gross trailer wt.) max. Trailer tongue wt. (see note) 3.6l/ automatic 3.73 two–door sport model (4wd) 6,309 lbs (2 862 kg) 25 sq ft (2.32 sq m) 2,000 lbs (907 kg) 200 lbs (91 kg) 3.6l/manual 3.21 two–door sahara ...

  • Page 530

    Engine/ transmission axle model gcwr (gross combined wt. Rating) frontal area max. Gtw (gross trailer wt.) max. Trailer tongue wt. (see note) 3.6l/ automatic 3.21 two–door sahara model (4wd) 6,368 lbs (2 888 kg) 25 sq ft (2.32 sq m) 2,000 lbs (907 kg) 200 lbs (91 kg) 3.6l/ automatic 3.73 two–door sa...

  • Page 531

    Engine/ transmission axle model gcwr (gross combined wt. Rating) frontal area max. Gtw (gross trailer wt.) max. Trailer tongue wt. (see note) 3.6l/ automatic 3.73 two–door rubicon model (4wd) 6,458 lbs (2 929 kg) 25 sq ft (2.32 sq m) 2,000 lbs (907 kg) 200 lbs (91 kg) 3.6l/ automatic 4.10 two–door r...

  • Page 532

    Engine/ transmission axle model gcwr (gross combined wt. Rating) frontal area max. Gtw (gross trailer wt.) max. Trailer tongue wt. (see note) 3.6l/ automatic 3.21 four–door sport model (4wd) 6,566 lbs (2 978 kg) 32 sq ft (2.97 sq m) 2,000 lbs (907 kg) 200 lbs (91 kg) 3.6l/ automatic 3.73 four–door s...

  • Page 533

    Engine/ transmission axle model gcwr (gross combined wt. Rating) frontal area max. Gtw (gross trailer wt.) max. Trailer tongue wt. (see note) 3.6l/ automatic 3.21 four–door sahara model (4wd) 6,782 lbs (3 076 kg) 32 sq ft (2.97 sq m) 2,000 lbs (907 kg) 200 lbs (91 kg) 3.6l/ automatic 3.73 four–door ...

  • Page 534

    Engine/ transmission axle model gcwr (gross combined wt. Rating) frontal area max. Gtw (gross trailer wt.) max. Trailer tongue wt. (see note) 3.6l/ automatic 4.10 four–door rubicon model (4wd) 8,347 lbs (3 786 kg) 32 sq ft (2.97 sq m) 3,500 lbs (1 587 kg) 350 lbs (159 kg) refer to local laws for max...

  • Page 535

    Never exceed the maximum tongue weight stamped on your bumper or trailer hitch. Consider the following items when computing the weight on the rear axle of the vehicle: • the tongue weight of the trailer. • the weight of any other type of cargo or equipment put in or on your vehicle. • the weight of ...

  • Page 536

    Caution! • do not tow a trailer at all during the first 500 miles (805 km) the new vehicle is driven. The engine, axle or other parts could be damaged. • then, during the first 500 miles (805 km) that a trailer is towed, do not drive over 50 mph (80 km/h) and do not make starts at full throttle. Thi...

  • Page 537

    Warning! (continued) • safety chains must always be used between your vehicle and trailer. Always connect the chains to the frame or hook retainers of the vehicle hitch. Cross the chains under the trailer tongue and allow enough slack for turning corners. • vehicles with trailers should not be parke...

  • Page 538

    Towing requirements – tires – proper tire inflation pressures are essential to the safe and satisfactory operation of your vehicle. Refer to “tires – general information” in “starting and oper- ating” for proper tire inflation procedures. – check the trailer tires for proper tire inflation pressures...

  • Page 539

    Caution! If the trailer weighs more than 1,000 lbs (454 kg) loaded, it should have its own brakes and they should be of adequate capacity. Failure to do this could lead to accelerated brake lining wear, higher brake pedal effort, and longer stopping distances. Warning! • do not connect trailer brake...

  • Page 540

    The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector. Refer to the following illustration. Towing tips before setting out on a trip, practice turning, stopping and backing the trailer in an area away from heavy traffic. If using a manual tra...

  • Page 541

    If you regularly tow a trailer for more than 45 minutes of continuous operation, then change the trans- mission fluid and filter as specified for ⬙ police, taxi, fleet, or frequent trailer towing. ⬙ refer to the “maintenance schedule” for the proper maintenance intervals. Note: check the automatic t...

  • Page 542

    Recreational towing (behind motorhome, etc.) towing this vehicle behind another vehicle towing condition wheels off the ground four-wheel drive models flat tow none see instructions • automatic transmission in park • manual transmission in gear (not in neutral [n]) • transfer case in neutral (n) • t...

  • Page 543

    Recreational towing – four-wheel drive models note: the transfer case must be shifted into neutral (n), automatic transmission must be shifted into park, and manual transmission must be placed in gear (not in neutral) for recreational towing. Caution! • front or rear wheel lifts should not be used. ...

  • Page 544

    Shifting into neutral (n) use the following procedure to prepare your vehicle for recreational towing. Warning! You or others could be injured or killed if you leave the vehicle unattended with the transfer case in the neutral (n) position without first fully engaging the parking brake. The transfer...

  • Page 545

    8. Release the brake pedal (and clutch pedal on manual transmissions) for five seconds and ensure that there is no vehicle movement. 9. Repeat steps 7 and 8 with automatic transmission in drive or manual transmission in first gear. 10. Turn the engine off. 11. Firmly apply the parking brake. 12. Shi...

  • Page 546

    Shifting out of neutral (n) use the following procedure to prepare your vehicle for normal usage. 1. Bring the vehicle to a complete stop, leaving it con- nected to the tow vehicle. 2. Firmly apply the parking brake. 3. Turn the ignition switch to the lock/off position. 4. Turn the ignition switch t...

  • Page 547: Contents

    What to do in emergencies contents 䡵 hazard warning flashers . . . . . . . . . . .546 䡵 if your engine overheats . . . . . . . . . . . .546 䡵 jacking and tire changing . . . . . . . . . .547 ▫ jack location . . . . . . . . . . . . . . . . . . . . . . . .548 ▫ spare tire stowage . . . . . . . . . . ....

  • Page 548

    Hazard warning flashers the hazard warning flasher switch is located on the instrument panel below the climate controls. Press the switch to turn on the hazard warning flasher. When the switch is activated, all direc- tional turn signals will flash on and off to warn oncoming traffic of an emergency...

  • Page 549

    Note: there are steps that you can take to slow down an impending overheat condition: • if your air conditioner (a/c) is on, turn it off. The a/c system adds heat to the engine cooling system and turning the a/c off can help remove this heat. • you can also turn the temperature control to maximum he...

  • Page 550

    Warning! (continued) • the jack is designed to be used as a tool for changing tires only. The jack should not be used to lift the vehicle for service purposes. The vehicle should be jacked on a firm level surface only. Avoid ice or slippery areas. Jack location the jack and lug wrench are located in...

  • Page 551

    Spare tire stowage to remove the spare tire from the carrier, remove the tire cover, if equipped, and remove the lug nuts with the lug wrench turning them counterclockwise. Note: if you have added aftermarket accessories to the spare tire mounted carrier, it cannot exceed a gross weight of 69 lbs (3...

  • Page 552

    4. Shift the automatic transmission into park, or a manual transmission into reverse. 5. Turn the ignition to lock. Block both the front and rear of the wheel diagonally opposite of the jack- ing position. For example, if changing the right front tire, block the left rear wheel. Note: passengers sho...

  • Page 553

    Warning! (continued) • do not let anyone sit in the vehicle when it is on a jack. • do not get under the vehicle when it is on a jack. If you need to get under a raised vehicle, take it to a service center where it can be raised on a lift. • only use the jack in the positions indicated and for lifti...

  • Page 554

    3. Assemble the jack and jacking tools. Connect the jack handle driver to the extension, then to the lug wrench. 4. Operate the jack from the front or the rear of the vehicle. Place the jack under the axle tube, as shown. Do not raise the vehicle until you are sure the jack is fully engaged. 5. Rais...

  • Page 555

    Warning! Raising the vehicle higher than necessary can make the vehicle less stable and cause a collision. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. 6. Remove the lug nuts and wheel. 7. Position the spare wheel/tire on the vehicle and inst...

  • Page 556

    8. Lower the vehicle by turning the jack screw to the left, and remove the jack. 9. Finish tightening the lug nuts. Push down on the wrench while tightening for increased leverage. Alter- nate nuts until each nut has been tightened twice. The correct wheel nut tightness is 95 ft lbs (130 n·m). If in...

  • Page 557

    Warning! To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts fully until the vehicle has been lowered. Failure to follow this warning may result in personal injury. 3. Lower the vehicle to the ground by turning the jack handle counterclockwise. 4. Finish tightening the...

  • Page 558

    Warning! Do not attempt jump-starting if the battery is frozen. It could rupture or explode and cause personal injury. Preparations for jump-start the battery in your vehicle is located in the right rear of the engine compartment, behind the power distribution center. Positive battery post 556 what ...

  • Page 559

    Warning! • take care to avoid the radiator cooling fan when- ever the hood is raised. It can start anytime the ignition switch is on. You can be injured by moving fan blades. • remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact. You co...

  • Page 560

    Jump-starting procedure warning! Failure to follow this procedure could result in per- sonal injury or property damage due to battery ex- plosion. Caution! Failure to follow these procedures could result in damage to the charging system of the booster vehicle or the discharged vehicle. 1. Connect th...

  • Page 561

    Once the engine is started, remove the jumper cables in the reverse sequence: 6. Disconnect the negative (-) jumper cable from the engine ground of the vehicle with the discharged battery. 7. Disconnect the negative end (-) of the jumper cable from the negative (-) post of the booster battery. 8. Di...

  • Page 562

    Caution! Racing the engine or spinning the wheels may lead to transmission overheating and failure. Allow the en- gine to idle with the transmission in neutral for at least one minute after every five rocking-motion cycles. This will minimize overheating and reduce the risk of transmission failure d...

  • Page 563

    Warning! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause damage, or even failure, of the axle and tires. A tire could explode and injure someone. Do not spin your vehi- cle’s wheels faster than 30 mph (48 km/h) or for longer than 30 seconds continuously w...

  • Page 564

    Shift lever override if a malfunction occurs and the shift lever cannot be moved out of the park position, you can use the following procedure to temporarily move the shift lever: 1. Turn the engine off. 2. Firmly apply the parking brake. 3. Using a small screwdriver or similar tool, remove the shif...

  • Page 565

    7. Move the shift lever to the neutral position. 8. The vehicle may then be started in neutral. 9. Reinstall the shift lever override access cover. Towing a disabled vehicle this section describes procedures for towing a disabled vehicle using a commercial wrecker service. If the trans- mission and ...

  • Page 566

    Proper towing or lifting equipment is required to prevent damage to your vehicle. Use only tow bars and other equipment designed for this purpose, following equip- ment manufacturer’s instructions. Use of safety chains is mandatory. Attach a tow bar or other towing device to main structural members ...

  • Page 567

    Four–wheel drive models the manufacturer recommends towing with all wheels off the ground. Acceptable methods are to tow the vehicle on a flatbed or with one end of the vehicle raised and the opposite end on a towing dolly. If flatbed equipment is not available and the transfer case is operable, the...

  • Page 569: Maintaining Your Vehicle

    Maintaining your vehicle contents 䡵 engine compartment — 3.6l . . . . . . . . . .569 䡵 onboard diagnostic system — obd ii . .570 ▫ loose fuel filler cap message . . . . . . . . . . . .570 䡵 emissions inspection and maintenance programs . . . . . . . . . . . . .571 䡵 replacement parts . . . . . . . ....

  • Page 570

    ▫ clutch hydraulic system (manual transmission) – if equipped . . . . . . . . . . . . . .597 ▫ manual transmission – if equipped . . . . . . . .597 ▫ transfer case . . . . . . . . . . . . . . . . . . . . . . . .598 ▫ front/rear axle fluid . . . . . . . . . . . . . . . . . .599 ▫ appearance care and ...

  • Page 571

    Engine compartment — 3.6l 1 — integrated power module (fuses) 7 — washer fluid reservoir 2 — battery 8 — engine coolant reservoir 3 — engine oil dipstick 9 — air cleaner filter 4 — automatic transmission dipstick (under engine cover) 10 — coolant pressure cap 5 — engine oil fill 11 — power steering ...

  • Page 572

    Onboard diagnostic system — obd ii your vehicle is equipped with a sophisticated onboard diagnostic system called obd ii. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide ex...

  • Page 573

    Gas cap is properly tightened. Press the odometer reset button to turn the message off. If the problem persists, the message will appear the next time the vehicle is started. This might indicate a damaged cap. If the prob- lem is detected twice in a row, the system will turn on the mil. Resolving th...

  • Page 574

    4. Approximately 15 seconds later, one of two things will happen: • the mil will flash for about 10 seconds and then return to being fully illuminated until you turn off the ignition or start the engine. This means that your vehicle’s obd ii system is not ready and you should not proceed to the i/m ...

  • Page 575

    Dealer service your authorized dealer has the qualified service person- nel, special tools, and equipment to perform all service operations in an expert manner. Service manuals are available which include detailed service information for your vehicle. Refer to these service manuals before attempting...

  • Page 576

    Caution! (continued) • your vehicle has been built with improved fluids that protect the performance and durability of your vehicle and also allow extended maintenance inter- vals. Do not use chemical flushes in these compo- nents as the chemicals can damage your engine, transmission, power steering...

  • Page 577

    Change engine oil the oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance. Refer to the “maintenance schedule” for further informa- tion. Note:under no circumstances should oil change inter- vals exceed 10,000 miles (16,000 km) or twelve mont...

  • Page 578

    Engine oil viscosity – 3.6l engine sae 5w-20 engine oil is recommended for all operating temperatures. This engine oil improves low temperature starting and vehicle fuel economy. The engine oil filler cap also shows the recommended engine oil viscosity for your engine. For information on engine oil ...

  • Page 579

    Engine oil filter selection this manufacturer’s engines have a full-flow type oil filter. Use a filter of this type for replacement. The quality of replacement filters varies considerably. Only high quality filters should be used to assure most efficient service. Mopar® engine oil filters are a high...

  • Page 580

    Warning! • battery fluid is a corrosive acid solution and can burn or even blind you. Do not allow battery fluid to contact your eyes, skin, or clothing. Do not lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area imme- diately with large amounts of water. R...

  • Page 581

    Air conditioner maintenance for best possible performance, your air conditioner should be checked and serviced by an authorized dealer at the start of each warm season. This service should include cleaning of the condenser fins and a performance test. Drive belt tension should also be checked at thi...

  • Page 582

    Refrigerant recovery and recycling r-134a air conditioning refrigerant is a hydrofluoro- carbon (hfc) that is endorsed by the environmental protection agency and is an ozone-saving product. How- ever, the manufacturer recommends that air conditioning service be performed by authorized dealer or othe...

  • Page 583

    4. Disengage the two retaining tabs that secure the two air filter access doors to the hvac housing. 5. Open the two air filter access doors. 6. Remove the two particulate air filters from the hvac air inlet housing. Pull the filter elements straight out of the housing, one at a time. 7 maintaining ...

  • Page 584

    7. Install the a/c air filter with the air filter position indicators pointing in the same direction as removal. Caution! The a/c air filter is identified with an arrow to indicate airflow direction through the filter. Failure to properly install the filter will result in the need to replace it more...

  • Page 585

    Windshield wiper blades clean the rubber edges of the wiper blades and the windshield periodically with a sponge or soft cloth and a mild nonabrasive cleaner. This will remove accumula- tions of salt or road film. Operation of the wipers on dry glass for long periods may cause deterioration of the w...

  • Page 586

    Warning! Commercial windshield washer solvents are flammable. They could ignite and burn you. Care must be exercised when filling or working around the washer solution. Exhaust system the best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust syst...

  • Page 587

    Caution! • the catalytic converter requires the use of un- leaded fuel only. Leaded gasoline will destroy the effectiveness of the catalyst as an emissions control device and may seriously reduce engine perfor- mance and cause serious damage to the engine. • damage to the catalytic converter can res...

  • Page 588

    To minimize the possibility of catalytic converter dam- age: • do not shut off the engine or interrupt the ignition, when the transmission is in gear and the vehicle is in motion. • do not try to start the engine by pushing or towing the vehicle. • do not idle the engine with any spark plug wires di...

  • Page 589

    Engine coolant checks check the engine coolant (antifreeze) protection every 12 months (before the onset of freezing weather, where applicable). If the engine coolant (antifreeze) is dirty or rusty in appearance, the system should be drained, flushed and refilled with fresh engine coolant (anti- fre...

  • Page 590

    Selection of coolant refer to “fluids, lubricants, and genuine parts” in “maintaining your vehicle” for further information. Caution! • mixing of engine coolant (antifreeze) other than speci- fied organic additive technology (oat) engine cool- ant (antifreeze), may result in engine damage and may de...

  • Page 591

    Important that you use the same engine coolant (oat coolant conforming to ms-12106) throughout the life of your vehicle. Please review these recommendations for using organic additive technology (oat) engine coolant (antifreeze) that meets the requirements of chrysler material stan- dard ms-12106. W...

  • Page 592

    The cap should be inspected and cleaned if there is any accumulation of foreign material on the sealing surfaces. Warning! • the warning words “do not open hot” on the cooling system pressure cap are a safety precaution. Never add engine coolant (antifreeze) when the engine is overheated. Do not loo...

  • Page 593

    Engine coolant level the coolant bottle provides a quick visual method for determining that the coolant level is adequate. With the engine idling, and warm to normal operating tempera- ture, the level of the engine coolant (antifreeze) in the bottle should be between the ranges indicated on the bott...

  • Page 594

    • if frequent engine coolant (antifreeze) additions are required, the cooling system should be pressure tested for leaks. • maintain engine coolant (antifreeze) concentration at a minimum of 50% oat coolant (conforming to ms-12106) and distilled water for proper corrosion protection of your engine w...

  • Page 595

    Brake master cylinder the fluid level in the master cylinders should be checked whenever the vehicle is serviced. If necessary, add fluid to bring level to the full level mark on the side of the reservoir of the brake master cylinder. With disc brakes, fluid level can be expected to fall as the brak...

  • Page 596

    Warning! (continued) • overfilling the brake fluid reservoir can result in spilling brake fluid on hot engine parts, causing the brake fluid to catch fire. Brake fluid can also damage painted and vinyl surfaces, care should be taken to avoid its contact with these surfaces. • do not allow petroleum ...

  • Page 597

    Special additives the manufacturer strongly recommends against using any special additives in the transmission. Automatic transmission fluid (atf) is an engineered product and its performance may be impaired by supple- mental additives. Therefore, do not add any fluid addi- tives to the transmission...

  • Page 598

    4. Place the shift lever momentarily into each gear posi- tion (allowing time for the transmission to fully en- gage in each position), ending with the shift lever in park. 5. Remove the dipstick, wipe it clean and reinsert it until seated. 6. Remove the dipstick again and note the fluid level on bo...

  • Page 599

    Caution! If the fluid temperature is below 50° f (10° c), it may not register on the dipstick. Do not add fluid until the temperature is elevated enough to produce an accurate reading. Run the engine at idle, in park, to warm the fluid. 7. Check for leaks. Release the parking brake. Note: to prevent...

  • Page 600

    Fluid level check check the fluid level by removing the fill plug. The fluid level should be between the bottom of the fill hole and a point not more than 3/16 in (4.76 mm) below the bottom of the hole. Add fluid, if necessary, to maintain the proper level. Frequency of fluid change under normal ope...

  • Page 601

    Adding fluid fluid should be added only at filler hole until fluid begins to run out of the hole. Drain first remove the fill plug (b), then the drain plug (c). The recommended tightening torque for the drain and fill plugs is 15 to 25 ft lbs (20 to 34 n·m). Caution! When replacing the plugs, do not...

  • Page 602

    Selection of lubricant use only manufacturer’s recommended fluid. Refer to “fluids, lubricants, and genuine parts” in “maintaining your vehicle” for further information. Appearance care and protection from corrosion protection of body and paint from corrosion vehicle body care requirements vary acco...

  • Page 603

    Washing • wash your vehicle regularly. Always wash your ve- hicle in the shade using mopar® car wash, or a mild car wash soap, and rinse the panels completely with clear water. • if insects, tar, or other similar deposits have accumu- lated on your vehicle, use mopar® super kleen bug and tar remover...

  • Page 604

    • if your vehicle is damaged due to a collision or similar cause that destroys the paint and protective coating, have your vehicle repaired as soon as possible. The cost of such repairs is considered the responsibility of the owner. • if you carry special cargo such as chemicals, fertilizers, de-ice...

  • Page 605

    Interior care use mopar® total clean or equivalent to clean fabric upholstery and carpeting. Interior trim should be cleaned starting with a damp cloth, a damp cloth with mopar® total clean or equiva- lent , then mopar® spot & stain remover or equivalent if absolutely necessary. Do not use harsh cle...

  • Page 606

    When cleaning the rear view mirror, spray cleaner on the towel or rag that you are using. Do not spray cleaner directly on the mirror. Cleaning plastic instrument cluster lenses the lenses in front of the instruments in this vehicle are molded in clear plastic. When cleaning the lenses, care must be...

  • Page 607

    • do not allow any vinyl cleaner to run down and dry on the paint, leaving a streak. • after cleaning your vehicle’s fabric top, always make sure it is completely dry before lowering. • be especially careful when washing the windows by following the directions for “care of fabric top windows.” washi...

  • Page 608

    Caution! (continued) • the front panel(s) must be positioned properly to ensure sealing. Improper installation can cause water to leak into the vehicle’s interior. Care of fabric top windows caution! Your vehicle’s fabric top has pliable plastic windows which can be scratched unless special care is ...

  • Page 609

    To maintain ease of use of the window zippers, each window zipper should be cleaned and lubricated regularly. Use mopar® soft top zipper cleaner and lubricant or equivalent to ease zipper operation. Before applying, make sure the zipper teeth are clear of sand, mud, and other materials. Clean both s...

  • Page 610

    Cavity cartridge fuse mini fuse description j1 — — j2 30 amp pink transfer case module j3 — — j4 25 amp natural driver door node j5 25 amp natural passenger door node j6 40 amp green anti-lock brake system (abs) pump/stability control system j7 30 amp pink anti-lock brake system (abs) valve/stabilit...

  • Page 611

    Cavity cartridge fuse mini fuse description j14 40 amp green rear defroster j15 40 amp green front blower j17 40 amp green starter solenoid j18 20 amp blue powertrain control module (pcm) trans range j19 60 amp yellow radiator fan j20 30 amp pink front wiper lo/hi j21 20 amp blue front/rear washer j...

  • Page 612

    Cavity cartridge fuse mini fuse description m7 20 amp yellow power outlet #2 (batt/acc select) m8 20 amp yellow front heated seat m9 20 amp yellow rear heated seat – if equipped m10 15 amp blue ignition off draw – vehicle entertainment system, satellite digital audio receiver (sdars), dvd, hands-fre...

  • Page 613

    Cavity cartridge fuse mini fuse description m15 20 amp yellow climate control system, rear view mirror, cabin compartment node, transfer case switch, multi- function control switch, tire pressure monitor, glow plug module – export diesel only m16 10 amp red airbag module m17 15 amp blue left tail/li...

  • Page 614

    Cavity cartridge fuse mini fuse description m26 10 amp red power window switch, driver window switch m27 10 amp red ignition switch feed, wireless module m28 10 amp red powertrain control module m29 10 amp red powertrain m30 15 amp blue wiper motor frt, j1962 diagnostic feed m31 20 amp yellow backup...

  • Page 615

    Caution! • when installing the integrated power module cover, it is important to ensure the cover is properly positioned and fully latched. Failure to do so may allow water to get into the integrated power mod- ule, and possibly result in an electrical system failure. • when replacing a blown fuse, ...

  • Page 616

    Replacement bulbs interior bulbs bulb number automatic transmission indicator lamp 658 heater control lamps (2) 194 rocker switch indicator lamp (rear window defogger, and rear wash/wipe) ** soundbar dome lamp 912 ** bulbs only available from authorized dealer. Exterior bulbs bulb number headlamps (...

  • Page 617

    Bulb replacement note: lens fogging can occur under certain atmo- spheric conditions. This will usually clear as atmospheric conditions change to allow the condensation to change back into a vapor. Turning the lamps on will usually accelerate the clearing process. Headlamp 1. Open hood and support u...

  • Page 618

    Front park/turn signal 1. Remove the front grille. Turn the retainers along the top 1/4 turn counterclockwise and remove. 2. Pull the bottom of the grille away starting at one side and working toward the other. 3. Turn the socket assembly 1/4 turn counterclockwise and remove from housing. Pull the b...

  • Page 619

    Rear tail, stop, turn signal, and backup lamp 1. Remove the two inboard screws attaching the tail light housing to the body. Do not remove the outer screws at any time. 2. Separate the housing from the body by pushing the lamp inboard while pulling the lamp away from the body. 3. Rotate the appropri...

  • Page 620

    Fluid capacities u.S. Metric fuel (approximate) — two door models 18.6 gallons 70 liters fuel (approximate) — four door models 22.5 gallons 85 liters engine oil with filter 3.6l engine 6 quarts 5.6 liters cooling system * 3.6l engine (mopar® antifreeze/engine coolant 10 year/150,000 mile formula or ...

  • Page 621

    Fluids, lubricants and genuine parts engine component fluid, lubricant, or genuine part engine coolant we recommend you use mopar® antifreeze/coolant 10 year/ 150,000 mile formula oat (organic additive technology) or equivalent meeting the requirements of chrysler material standard ms-12106. Engine ...

  • Page 622

    Chassis component fluid, lubricant, or genuine part automatic transmission – if equipped we recommend you only use mopar® atf+4® automatic transmission fluid. Failure to use atf+4 fluid may affect the function or performance of your transmission. Manual transmission – if equipped we recommend you us...

  • Page 623: Maintenance Schedules

    Maintenance schedules contents 䡵 maintenance schedule . . . . . . . . . . . . .622 ▫ maintenance chart. . . . . . . . . . . . . . . . . . . . .624 8 m a i n t e n a n c e s c h e d u l e s.

  • Page 624

    Maintenance schedule your vehicle is equipped with an automatic oil change indicator system. The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance. Based on engine operation conditions, the oil change indicator message will illuminate. This...

  • Page 625

    Note: under no circumstances should oil change inter- vals exceed 10,000 miles (16,000 km) or twelve months, whichever comes first. Once a month or before a long trip: • check engine oil level • check windshield washer fluid level • check the tire inflation pressures and look for unusual wear or dam...

  • Page 626

    Maintenance chart refer to the maintenance schedules on the following pages for the required maintenance intervals. Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 ...

  • Page 627

    Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,000 192,000 208,0...

  • Page 628

    Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,000 192,000 208,0...

  • Page 629

    Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,000 192,000 208,0...

  • Page 630

    Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,000 192,000 208,0...

  • Page 631

    Warning! • you can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent me- chanic. • failure to properly inspect and m...

  • Page 633: Contents

    If you need consumer assistance contents 䡵 suggestions for obtaining service for your vehicle . . . . . . . . . . . . . . . . . . .633 ▫ prepare for the appointment. . . . . . . . . . . . .633 ▫ prepare a list . . . . . . . . . . . . . . . . . . . . . . . .633 ▫ be reasonable with requests . . . . ....

  • Page 634

    䡵 publication order forms . . . . . . . . . . . .638 䡵 department of transportation uniform tire quality grades . . . . . . . . .639 ▫ treadwear. . . . . . . . . . . . . . . . . . . . . . . . . . .640 ▫ traction grades . . . . . . . . . . . . . . . . . . . . . . .640 ▫ temperature grades. . . . . . ...

  • Page 635

    Suggestions for obtaining service for your vehicle prepare for the appointment if you are having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty. Discuss additional charges with the service manager....

  • Page 636

    Are most concerned that you get prompt and high quality service. The manufacturer’s authorized dealer have the facilities, factory-trained technicians, special tools, and the latest information to ensure the vehicle is fixed correctly and in a timely manner. This is why you should always talk to an ...

  • Page 637

    Chrysler canada inc. Customer center p.O. Box 1621 windsor, ontario n9a 4h6 phone: (800) 465–2001 english / (800) 387–9983 french in mexico contact: av. Prolongacion paseo de la reforma, 1240 sante fe c.P. 05109 mexico, d. F. In mexico city: 5081-7568 outside mexico city: 1-800-505-1300 customer ass...

  • Page 638

    Service contract you may have purchased a service contract for a vehicle to help protect you from the high cost of unexpected repairs after the manufacturer’s new vehicle limited warranty expires. The manufacturer stands behind only the manufacturer’s service contracts. If you purchased a manufactur...

  • Page 639

    Warning! (continued) products of component wear contain, or emit, chemi- cals known to the state of california to cause cancer and birth defects, or other reproductive harm. Warranty information see the warranty information booklet, located on the dvd, for the terms and provisions of chrysler group ...

  • Page 640

    To contact nhtsa, you may either call the auto safety hotline toll free at 1–888–327–4236 (tty: 1–800–424– 9153), or go to http://www.Safercar.Gov; or write to: administra- tor, nhtsa, 1200 new jersey avenue, se., west building, washington, d.C. 20590. You can also obtain other information about mot...

  • Page 641

    Diagnostic procedure manuals diagnostic procedure manuals are filled with diagrams, charts and detailed illustrations. These practical manuals make it easy for students and technicians to find and fix problems on computer-controlled vehicle systems and features. They show exactly how to find and cor...

  • Page 642

    Treadwear the treadwear grade is a comparative rating, based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half times as well on the government course as a tire graded 100. The relativ...

  • Page 643

    Temperature grades the temperature grades are a (the highest), b, and c, representing the tire’s resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the mater...

  • Page 645: Index

    Index 10

  • Page 646

    Abs (anti-lock brake system) . . . . . . . . . . . . . . . .307 adding engine coolant (antifreeze) . . . . . . . . . . . .588 adding fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . .517 additives, fuel . . . . . . . . . . . . . . . . . . . . . . . . . . .515 airbag. . . . . . . . . . . ...

  • Page 647

    Automatic transmission . . . . . . . . . . . . . . . . . . . .424 adding fluid . . . . . . . . . . . . . . . . . . . . . . . . . .597 fluid and filter changes . . . . . . . . . . . . . . . . . .597 fluid change . . . . . . . . . . . . . . . . . . . . . . . . . .597 fluid level check . . . . . . . . ...

  • Page 648

    Cellular phone . . . . . . . . . . . . . . . . . . . . . . . . . . .115 center high mounted stop light . . . . . . . . . . . . . .617 certification label. . . . . . . . . . . . . . . . . . . . . . . . .519 chains, tire . . . . . . . . . . . . . . . . . . . . . . . . . . . . .499 changing a flat tire...

  • Page 649

    Pressure cap . . . . . . . . . . . . . . . . . . . . . . . . . .589 radiator cap . . . . . . . . . . . . . . . . . . . . . . . . . .589 selection of coolant (antifreeze) . . . . . . . . . . . . .588 corrosion protection . . . . . . . . . . . . . . . . . . . . . . .600 cruise light . . . . . . . . . ...

  • Page 650

    Electronic speed control (cruise control) . . . . . . . .180 electronic stability control (esc) . . . . . . . . . . . . . .467 electronic throttle control warning light . . . . . . . .318 electronic vehicle information center (evic) . . . . . .319 emergency brake . . . . . . . . . . . . . . . . . . ...

  • Page 651

    Extender, seat belt . . . . . . . . . . . . . . . . . . . . . . . . .61 exterior lights . . . . . . . . . . . . . . . . . . . . . . . . . . .103 fabric care. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .603 fabric top . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .604 filters...

  • Page 652

    Gasoline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .513 gauge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .304 materials added . . . . . . . . . . . . . . . . . . . . . . . .515 methanol . . . . . . . . . . . . . . . . . . . . . . . . . . . . .514 octane rating . . . ...

  • Page 653

    Passing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .172 replacing . . . . . . . . . . . . . . . . . . . . . . . . . . . . .615 switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .169 head restraints . . . . . . . . . . . . . . . . . . . . . . . . . .162 heated mirrors ...

  • Page 654

    Jack operation . . . . . . . . . . . . . . . . . . . . . . . . . . .547 jump starting . . . . . . . . . . . . . . . . . . . . . . . . . . . .555 key-in reminder . . . . . . . . . . . . . . . . . . . . . . . . . .16 keyless entry system . . . . . . . . . . . . . . . . . . . . . . .24 key, programming...

  • Page 655

    Hazard warning flasher . . . . . . . . . . . . . . . . . .546 headlights . . . . . . . . . . . . . . . . . . . . . . . . . . . .169 headlight switch . . . . . . . . . . . . . . . . . . . . . . .169 high beam . . . . . . . . . . . . . . . . . . . . . . . . . . . .305 high beam indicator . . . . . . ....

  • Page 656

    Maintenance schedule . . . . . . . . . . . . . . . . . . . . . .622 malfunction indicator light (check engine). . . . . . .315 manual, service . . . . . . . . . . . . . . . . . . . . . . . . . .638 manual transmission . . . . . . . . . . . . . . . . . . . . . .418 fluid level check . . . . . . . . ....

  • Page 657

    Filter disposal . . . . . . . . . . . . . . . . . . . . . . . . .576 identification logo . . . . . . . . . . . . . . . . . . . . . .575 materials added to . . . . . . . . . . . . . . . . . . . . . .576 pressure warning light . . . . . . . . . . . . . . . . . . .305 recommendation . . . . . . . . . ....

  • Page 658

    Preparation for jacking . . . . . . . . . . . . . . . . . . . . .549 pretensioners seat belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60 programmable electronic features . . . . . . . . . . . . .335 radial ply tires . . . . . . . . . . . . . . . . . . . . . . . . . .491 radiator c...

  • Page 659

    Safety checks inside vehicle . . . . . . . . . . . . . . . . .101 safety checks outside vehicle . . . . . . . . . . . . . . . .103 safety defects, reporting . . . . . . . . . . . . . . . . . . . .637 safety, exhaust gas . . . . . . . . . . . . . . . . . . . . . . . .100 safety information, tire . . ...

  • Page 660

    Service contract . . . . . . . . . . . . . . . . . . . . . . . . . .636 service manuals . . . . . . . . . . . . . . . . . . . . . . . . . .638 settings, personal . . . . . . . . . . . . . . . . . . . . . . . . .335 setting the clock. . . . . . . . . . . . . . . . . . . . . . . . . .341 shifting . . ...

  • Page 661

    Storage, behind the seat . . . . . . . . . . . . . . . . . . . .192 storage, vehicle. . . . . . . . . . . . . . . . . . . . . . . . . . .406 storing your vehicle . . . . . . . . . . . . . . . . . . . . . . .613 stuck, freeing. . . . . . . . . . . . . . . . . . . . . . . . . . . .559 sunrider. . . . ...

  • Page 662

    Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .476 sizes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .477 snow tires . . . . . . . . . . . . . . . . . . . . . . . . . . . .492 spare tire . . . . . . . . . . . . . . . . . . . . . . . . . . . . .549 spinning . . ...

  • Page 663

    Trip computer . . . . . . . . . . . . . . . . . . . . . . . . . . .319 trip odometer . . . . . . . . . . . . . . . . . . . . . . . . . . .312 trip odometer reset button. . . . . . . . . . . . . . . . . .310 turn signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . .171 uci connector . . ....

  • Page 664

    Windshield wipers . . . . . . . . . . . . . . . . . . . . . . . .176 wiper blade replacement . . . . . . . . . . . . . . . . . . .583 wiper, rear . . . . . . . . . . . . . . . . . . . . . . . . . . . . .297 662 index.

  • Page 665

    Installation of radio transmitting equipment special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained personnel. The following must be obser...

  • Page 666

    Wrangler includes wrangler unlimited chrysler group llc o w n e r ’ s m a n u a l 20 13 w rangler 13jk72-126-af sixth edition printed in u.S.A. 2 0 1 3.