1. DL manuals
  2. JEHNERT SOUND DESIGN
  3. Car Receiver
  4. 46149
  5. Installation Instructions Manual

JEHNERT SOUND DESIGN 46149 Installation Instructions Manual

Manual is about: JEHNERT SOUND DESIGN 46149 - BMW Z3 Car audio system

Summary of 46149

  • Page 1

    Sound sound d e s i g n jehnert bmw z 3 roadster / coupé / m 3 g u a r a n t e e 2003/by.Aj/fh - 15 - installation instructions in st al l. In st r. 7 5 1 4 9 /f h 0 4 /0 3 part-no. 75149 jehnert sound design development and production of car-audio-systems heinrich-hertz-str. 11 70794 filderstadt te...

  • Page 2: C O N T E N T S

    Packing list .......................................................................... 1. Disassembly of the door lining............................................... 2. Installation tweeter .............................................................. 3. Panel alignment / reference points .........

  • Page 3: Packing List  75149

    Packing unit check list door panel, covered (right / left) 2 speaker grill, covered (right / left) 2 tweeter 26 mm ( with perforated sheet metal,6.Ktn.Screw m4x8,washer ø 12mm) 2 midrange 100 mm q (each mounted on the panel with 4 sheet metal-screws) 2 woofer 160 mm (each mounted on the panel with 2...

  • Page 4

    9.1. Precisely align and carefully press grill into the velcro fasteners. The velcro fastener makes a crackling sound when it is closed correctly. 9.1. Precisely align and carefully press grill into the velcro fasteners. The velcro fastener makes a crackling sound when it is closed correctly. Removi...

  • Page 5: Loudspeaker Wiring Diagram

    Loudspeaker wiring diagram connect all loudspeakers and crossover circuits: h i g h p e r f o r m a nc e d e s i g n jehnert sound sound m i d r a n g e s p e a k e r m a d e i n g e r m a n y 2.1. Dismount factory installed tweeter 2.2. Install jehnert tweeter in the large mount opening beside the ...

  • Page 6: 3 . Panel Alignment

    3.1. Place the door lining on a plane surface. 3.2. Dismount the loudspeakers attached to the panel for transport protection. Retain the screws for later assembly. Place the panel without loudspeakers and grill on the door lining and align it: 3.3. Remove factory installed tray acc. To fig line (a) ...

  • Page 7

    7.2. Put the door-lining into the upper sealing of the car door tip: grease the upper door sealing with a residue-free lubricant before 7.3. Fit it in contrary order of succession as described on page no. 3 7.4. Important: spax screws 9-11 with washers as spacer: carefully tighten the screws with ø ...

  • Page 8

    6. Insulation of the door lining important tip: the use of 2x16mm mid-woofer /side may cause vibrations which lead to annoying rattle noises in the car door some helpful tips: • use the self-adhesive insulation fleece (art.No.: 27000) or a foam material for the backside of the door lining ( see fig....

  • Page 9

    6. Insulation of the door lining important tip: the use of 2x16mm mid-woofer /side may cause vibrations which lead to annoying rattle noises in the car door some helpful tips: • use the self-adhesive insulation fleece (art.No.: 27000) or a foam material for the backside of the door lining ( see fig....

  • Page 10

    7.2. Put the door-lining into the upper sealing of the car door tip: grease the upper door sealing with a residue-free lubricant before 7.3. Fit it in contrary order of succession as described on page no. 3 7.4. Important: spax screws 9-11 with washers as spacer: carefully tighten the screws with ø ...

  • Page 11: 3 . Panel Alignment

    3.1. Place the door lining on a plane surface. 3.2. Dismount the loudspeakers attached to the panel for transport protection. Retain the screws for later assembly. Place the panel without loudspeakers and grill on the door lining and align it: 3.3. Remove factory installed tray acc. To fig line (a) ...

  • Page 12: Loudspeaker Wiring Diagram

    Loudspeaker wiring diagram connect all loudspeakers and crossover circuits: h i g h p e r f o r m a nc e d e s i g n jehnert sound sound m i d r a n g e s p e a k e r m a d e i n g e r m a n y 2.1. Dismount factory installed tweeter 2.2. Install jehnert tweeter in the large mount opening beside the ...

  • Page 13

    9.1. Precisely align and carefully press grill into the velcro fasteners. The velcro fastener makes a crackling sound when it is closed correctly. 9.1. Precisely align and carefully press grill into the velcro fasteners. The velcro fastener makes a crackling sound when it is closed correctly. Removi...

  • Page 14: Packing List  75149

    Packing unit check list door panel, covered (right / left) 2 speaker grill, covered (right / left) 2 tweeter 26 mm ( with perforated sheet metal,6.Ktn.Screw m4x8,washer ø 12mm) 2 midrange 100 mm q (each mounted on the panel with 4 sheet metal-screws) 2 woofer 160 mm (each mounted on the panel with 2...

  • Page 15: C O N T E N T S

    Packing list .......................................................................... 1. Disassembly of the door lining............................................... 2. Installation tweeter .............................................................. 3. Panel alignment / reference points .........

  • Page 16: Bmw Z 3

    Sound sound d e s i g n jehnert bmw z 3 roadster / coupé / m 3 g u a r a n t e e 2003/by.Aj/fh - 15 - installation instructions in st al l. In st r. 7 5 1 4 9 /f h 0 4 /0 3 part-no. 75149 jehnert sound design development and production of car-audio-systems heinrich-hertz-str. 11 70794 filderstadt te...