_____________________________________________________ operator’s manual for bm-12 beveling machine - 1 - safety instructions and operator ’s manual for bevelling machine bm-12 jei solutions ltd unit 30 & 31 new hall hey business park new hall hey road, rawtenstall, rossendale, lancashire bb4 6hr uni...
_____________________________________________________ operator’s manual for bm-12 beveling machine - 1 - general safety rules warning! Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and / or serious personal injury. The term ...
Bm-12 bevelling machine - 2 - when operating a power tool outside, use an outdoor extension cord marked “w- a” or “w”. These cords are rated for outdoor use and reduce the risk of electric shock. Personal safety stay alert, watch what you are doing and use common sense when operating a power tool. D...
Bm-12 bevelling machine - 3 - maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools, with sharp cutting edges are less likely to bind and are easier to control. Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may af...
Bm-12 bevelling machine - 4 - specific safety rules 1. Never operate to tool in an area with flammable solids, liquids or gases. Sparks from the commutator/carbon brushes could cause fire or explosion. Warning: risk of injury from high temperature chips! High temperature chips are expelled at high s...
Bm-12 bevelling machine - 5 - standard 45 degree tool holder for use with triangle indexable carbide cutter inserts to achieve quick and easy bevelling. Warning: the machine should not be converted or modified, e.G. For any other form of use, other than as specified in these operating instructions. ...
Bm-12 bevelling machine - 6 - unpacking carefully remove the tool and all loose items from the shipping container. Retain all packaging materials until after you have inspected and satisfactorily operated the machine. Carton contents 1. Operators manual 2. Hook spanner wrench 3. Spindle lock bar do ...
Bm-12 bevelling machine - 7 - zeroing-in the chamfer height – disconnect tool from power source. Note: the machine’s chamfer height is set at zero from the factory. If the setting is disturbed, it must be zeroed in. Follow the instructions below for zeroing-in. 1. Loosen the 2 lock knobs then loosen...
Bm-12 bevelling machine - 8 - arrange the indexable carbide insetrs in staggered, in order to achieve better bevelling result. 1. Using the supplied l-type torx wrench, loosen fixing screw and remove the carbide insert 2. Index the carbide insert to the next sharp edge or insert a new one as needed....
Bm-12 bevelling machine - 9 - starting and stopping tool make sure that the power circuit voltage is the same as that shown on the specification plate of the machine and that switch is “off” before connecting the tool to the power circuit. Switching the machine on and off to switch on: press trigger...
Bm-12 bevelling machine - 10 - how to use the tool effective control of the powerful tool requires two-handed operation at all times for maximum control and safety. Do not use this tool continuously for over 30 minutes. After using the machine for 30 minutes, have a break away from it for at least 2...
Bm-12 bevelling machine - 11 - the carbon brushes the carbon brushes are a normal wearing part and must be replaced when they reach their wear limit. Caution: always replace the brushes as a pair to replace: first unplug the machine. Carefully remove the 4 screws to separate the rear handle halves a...
Bm-12 bevelling machine - 12 -.
Bm-12 bevelling machine - 13 -.
Bm-12 bevelling machine - 14 -.
Bm-12 bevelling machine - 15 - jei six (6) month limited warranty jei solutions warrants the bm-12 bevelling machine to be free of defects in material and workmanship under normal use for a period of six months from date of purchase. This warranty does not cover damage or wear which arise from misus...
