1. DL manuals
  2. K-Star
  3. Ventilation Hood
  4. K1007 SERIES
  5. Operating Instructions Manual

K-Star K1007 SERIES Operating Instructions Manual

Manual is about: Range Hood

Summary of K1007 SERIES

  • Page 1

    Read and save this instructions for domestic cooking only installer: leave this manual with the homeowner. Homeowner: cleaning, maintenance and operating instructions on the coming pages. Range hood item no.: k1007 series/k1009 series/k1019 series refered model no.: 3388c/3388f/3388c2 number: e31211...

  • Page 2: Warning

    Intended for domestic cooking only warning to reduce the risk of fire, electric shock, or injury to persons, observe the following: 1. Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer at the address or telephone number listed in the warra...

  • Page 3: Caution

    Caution 1. To reduce risk of fire and to properly exhaust air, be sure to duct air outside. Do not vent exhaust air into spaces within walls or ceilings or into attics, crawl spaces, or garages. 2. Take care when using cleaning agents or detergents. 3. Avoid using food products that produce flames u...

  • Page 4: Prepare The Hood

    Prepare the hood unpack hood and check contents. You should receive: 1 - hood 1 - decorative flue assembly 1 - parts bag containing: 1 - mounting bracket 1 - installation instructions 1 - vent 1 - warranty card 1 - duct fixing support 1 - slidery duct fixing support 7 - mounting screws (4 x 50mm) 8 ...

  • Page 5: Warning

    Warning note: this range hood must be properly grounded. The unit should be installed by a qualified electrician in accordance with all applicable national and local electrical codes. The minimum hood distance above cooktop must not be less than 24’’. A maximum of 33” above cooktop is highly recomme...

  • Page 6: Install Mounting

    Install mounting brackets 1. After eveluating the height of the hood, place the hook center over installation location. Drill 3 holes of Ø8mm on a suitable place to fix the mounting brackets. 2. Put the drywall anchors into the holes and fix the mounting screws (4x50mm) into the anchors, and install...

  • Page 7: None-Ducted

    None-ducted recirculation filter installation type-a 1. Purchase a non-ducted recirculation filter from your dealer. 2. Install the filter by rotating it onto the equipment which is stands on two sides of the motor. Type-b 1. Purchase a non-ducted recirculation filter from your dealer. 2. Press the ...

  • Page 8

    Type-c 1. Purchase a non-ducted recirculation filter from your dealer. 2. Triangle shape and carbon filter bracket used for fixing the square carbon filter. 3. Fill the carbon filter base on the triangle corner 4. The magnets will make the carbon filter sucked on the hood!.

  • Page 9: Prepare The Hood

    Prepare the hood screw: 4x8mm note: on stainless steel hoods, carefully remove the plastic protective film from all exterior surfaces of the hood and decorative flues, prior to final installation. 5. Pick out the hood from the carton. 6. Install the vent into the duct connector of the cooker hood. 7...

  • Page 10

    4. Put the glass in the lead way, use four screws (4x25mm) with glass washer and rubber washer to fix the glass. (note: the screws and washers should be install as shown.) 5. Measure the height of the glass to the slidery duct fixing support. Adjust the height of the chimney according to the height....

  • Page 11: Maintenance

    Maintenance proper maintenance of the range hood will assure proper performance of the unit. Filters the filters must be cleaned approximately once every 30 hours of operation (when the central segment on the display goes on or starts blinking). Use a warm detergent solution. Grease filters are dish...

  • Page 12: Operation

    Operation controls always trun the hood on before cooking in order to establish an air flow in the kitchen. After turing off the range, let the hood run for a few minutes to clear the air.  electronic button(brighting words button and blue ring button) 1. Power: when power-on ,the output is off ,an...

  • Page 13

     lcd electric control 1. Power on: switch on the power supply, and the backlight is lit, displaying “24-hour system”. The output is then blocked up, and the soot machine enters standby status. The backlight disappear automatically 30 seconds later under the condition of none operation. 2. Press “la...

  • Page 14

     lcd touch control 1. Power: when power-on ,the backlight is lit .Then showing the “24-hour system”,the output is off, and the machine standby .Without any operation, the backlight disappear automatically after 30 seconds. 2. “light” key: press that key once, the lamp and the is lit. Press the key ...

  • Page 15: Halogen Bulbs

    Halogen bulbs always switch off the electricity supply before carrying out any operations on the appliance. To change bulbs: 1. Rotate the cover in anticlockwise, as shown. Caution: bulb may be hot,please rotate when the bulb is cool! 2. Replace with a type jc, 12volt, 20watt max, g-4 base bulb. Do ...

  • Page 16

    K-star international group inc. K-star electronic appliance inc. Toll free:(800) 893-2168 email:info@kstarus.Com http://www.Kstarus.Com.