- DL manuals
- K-Tech
- Telephone
- ET1401A
- Instruction Book
K-Tech ET1401A Instruction Book
Summary of ET1401A
Page 1
K-phone et401 emergency speakerphone instruction book sentry (et401a) fortress (et1401a) commander (et401a-oem) liberator (et401a-lp) please read carefully before installation and operation.
Page 2
Page 2.
Page 3: Table of Contents
Page 3 table of contents introduction ................................................................................... 4 pre-installation checklist .............................................................. 5 wiring ................................................................................
Page 4: Introduction
Page 4 introduction thank you for purchasing the k-tech k-phone et401 emergency speakerphone. This vandal resistant speakerphone is designed to provide reliable communication in the event of an emergency. Each unit features a tone dialer capable of dialing five twenty-digit numbers, a voice activate...
Page 5: Wiring
Page 5 wiring we strongly recommend that the wires used to supply the telephone line to k-tech emergency speakerphones be 20 awg shielded, twisted pair. The shield must be continuous from the speakerphone through the traveling cable to the incoming telephone line termination. Make sure the shield is...
Page 6: Wiring Diagram
Page 6 wiring diagram connect telephone line shield to true earth ground at one end only! Telephone line microphone speaker increase vol. 9 6 3 # * 1 4 7 2 5 8 0 but led + - 9.0 vdc in remote led 2v 7ma phone line r t remote button dry contacts 12 - 30v online prog aux power rings 5 - 7 - 9 - k-tech...
Page 7: Installation
Page 7 installation sentry (et401a) 1. Use the 3/32” allen wrench (included) to unscrew the fasteners and remove the rear enclosure. 2. Using the rear enclosure as a template, mark the mounting screw hole locations. 3. Drill holes for two #8 screws (included). 4. Mount the rear enclosure placing the...
Page 8: Liberator (Et401A-Lp)
Page 8 liberator (et401a-lp) 1. Use the 3/32” allen wrench (included) to unscrew the fasteners and remove the rear enclosure. 2. Using the rear enclosure as a template, mark the mounting screw hole locations. 3. Drill holes for two #8 screws (included). 4. Mount the rear enclosure placing the ground...
Page 9: Fortress (Et1401A)
Page 9 fortress (et1401a) 1. Determine the mounting location and cut a 10” x 7” (25 cm x 18 cm) opening to allow for the back enclosure. 2. Using the faceplate as a template, mark the mounting screw hole locations. 3. Drill holes for four #8 security screws (included). K-tech international, inc, tor...
Page 10: Commander (Et401A-Oem)
Page 10 commander (et401a-oem) 1. Using the faceplate as a template, align the microphone and speaker with the grill pattern; mark and install the mounting studs. 2. Mount the faceplate tightly against the back of the cop to avoid feedback between the microphone and speaker. Microphone speaker incre...
Page 11: Settings
Page 11 settings number of rings incoming the k-phone et401 emergency speakerphone will automatically answer an incoming call after either 5, 7, or 9 rings. You can easily set this number of rings by installing the jumper in the appropriate location. Factory default is 5 rings. Microphone speaker in...
Page 12: Programming
Page 12 programming easy, voice prompted programming directs the entry of feature settings and plays back the information entered for confirmation. Programming is done via the built-in keypad, or remotely by any touch-tone telephone. Note: a 9 vdc battery is required for programming using the built-...
Page 13: Voice Announcement 1
Page 13 voice announcement 1 voice announcement 1 will automatically play when the emergency call is answered. Once the 10 second message has played, two- way communication is possible. For best results, record the announcement in a noise free environment. Speak clearly into the microphone or teleph...
Page 14: Voice Announcement 2
Page 14 voice announcement 2 voice announcement 2 can be recorded to supply the called party with additional information. To play this announcement, the called party must hit “ * 2 ” (star two) on their telephone keypad. Activity enter voice prompt record voice announcement 2 * 2 "press pound to sta...
Page 15: Timer Minutes
Page 15 timer minutes this is the amount of time the k-phone et401 emergency speakerphone will remain on (unless the called party extends the timer). Activity enter voice prompt program timer minutes * 4 "enter timer minutes" enter time desired from 01 to 99 minutes, or "0 0" for infinite timer 0 5 ...
Page 16: Operation And Testing
Page 16 operation and testing 1. Press the activating push-button. The visual indicator will turn on, dial tone will be heard for a few seconds, then the first programmed emergency telephone number will dial. If busy or there is no answer, the second number will be dialed, etc. Once answered, the vi...
Page 17: Troubleshooting
Page 17 troubleshooting when the activating push-button is pressed, there is no response from the k-phone et401 emergency speakerphone (i.E. No dial tone is heard, the visual indicator doesn’t light). 1. Check the connections to the microphone, speaker, led, and button (n.O. Contacts) 2. Check that ...
Page 18: Specifications
Page 18 specifications power telephone line: 24 vdc minimum on-hook voltage; 30 ma minimum loop current 9 volt battery required for programming with integral keypad circuit protection varistor lightning suppressor and full wave polarity guard dialing five numbers up to 20 digits each (including 1 1/...
Page 19: Code Compliance
Page 19 code compliance k-tech has taken great care in ensuring that our telephone equipment meets all code requirements. There are however additional requirements that have to be met in order for the installation and operation to pass code. We will attempt to list requirements pertaining to the ins...
Page 20: Fcc Notice For Part 68
Page 20 fcc notice for part 68 this device has been granted a registration number by the federal communications commission, under part 68 rules and regulations for direct connection to the telephone lines. In order to comply with these fcc rules, the following instructions must be carefully read and...
Page 21: Fcc Notice For Part 15
Page 21 fcc notice for part 15 this device complies with part 15 of the fcc rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired oper...
Page 22: Ic Notice
Page 22 ic notice notice: the industry canada label identifies certified equipment. This certification means that the equipment meets telecommunications network protective, operational and safety requirements as prescribed in the appropriate terminal equipment requirements document(s). The departmen...
Page 23: Service & Warranty Agreement
Page 23 to order: • mail your purchase order to: k-tech international, inc. P.O. Box 1025 torrington, ct 06790 • fax your purchase order to k-tech international, inc. At (860) 489-4399. • call in your order to 1-800-993-9399 or (860) 489-9399 customer service: please call customer service at 1-800-9...
Page 24: Notes
Notes date installed: serial number: installer: location: phone line number: phone number(s) dialed: service/security company dialed: 1. 2. K-tech international, inc. 56 ella grasso avenue p.O. Box 1025 torrington, connecticut 06790 usa 1-800-993-9399 (860) 489-9399 – (860) 489-4399 fax www.Ktechonl...