- DL manuals
- K2 Bike
- Bicycle
- Bicycle
- Owner's Manual
K2 Bike Bicycle Owner's Manual - page 48
49
• Ask your dealer for copies of the manufacturer’s installation and service instructions for the components on
your bike, or contact the component manufacturer.
• Ask your dealer to recommend a book on bicycle repair.
• Ask your dealer about the availability of bicycle repair courses in your area.
Regardless of which option you select, we recommend that you ask your dealer to check the quality of your work
the first time you work on something and before you ride the bike, just to make sure that you did everything
correctly. Since that will require the time of a mechanic, there may be a modest charge for this service.
A. Service Intervals
Some service and maintenance can and should be performed by the owner, and require no special tools or
knowledge beyond what is presented in this manual. The following are examples of the type of service you should
perform yourself. All other service, maintenance and repair should be performed in a properly equipped facility by a
qualified bicycle mechanic using the correct tools and procedures specified by the manufacturer.
1. Break-in
Period. Your bike will last longer and work better if you break it in before riding it hard. Control
cables and wheel spokes may stretch or “seat” when a new bike is first used and may require readjustment by
your dealer. Your Mechanical Safety Check (Section 1.C) will help you identify some things that need
readjustment. But even if everything seems fine to you, it’s best to take your bike back to the dealer for a
checkup. Dealers typically suggest you bring the bike in for a 30-day checkup. Another way to judge when it’s
time for the first checkup is to bring the bike in after 3 to 5 hours of hard off-road use, or about 10 to 15 hours
of on-road or more casual off-road use. But if you think something is wrong with the bike, take it to your dealer
before riding it again.
2. Before Every Ride: Perform the Mechanical Safety Check (Section 1.C).
Summary of Bicycle
Page 2: K2 Bike Owner’S Manual
3 k2 bike owner’s manual for multi-speed bicycles - 2003 important: this manual contains important safety, performance and service information. Read it before you take the first ride on your new bicycle, and keep it for reference..
Page 3: K2 Bike Owner’S Manual
4 k2 bike owner’s manual for multi-speed bicycles - 2003 contents: general warning note to parents 1. First a. Bike fit b. Safety first c. Mechanical safety check d. First ride 2. Safety a. The basics b. Riding safety c. Off-road safety d. Wet weather riding e. Night riding f. Downhill or competitio...
Page 4
5 4. Tech a. Wheels 1. Wheel quick release description 2. Adjusting the quick release mechanism 3. Front wheel secondary retention devices 4. Removing and installing quick release wheels 5. Removing and installing bolt on wheels b. Seatpost quick release c. Brakes d. Shifting gears e. Pedals f. Bicy...
Page 5: General Warning:
6 general warning: like any sport, bicycling involves risk of injury. By choosing to ride a bicycle, you assume the responsibility for that risk, so you need to know — and to practice — the rules of safe and responsible riding and of proper use and maintenance. Proper use and maintenance of your bic...
Page 6: Note For Parents:
7 note for parents: as a parent or guardian, you are responsible for the activities and safety of your minor child, and that includes making sure the bicycle is properly fitted to the child; that it is in good repair and safe operating condition; that you and your child have learned and understand t...
Page 7
8 3. Are saddle and seatpost securely clamped? A correctly tightened saddle will allow no saddle movement in any direction. See section 3.B for details. 4. Are the stem and handlebars at the right height for you? If not, see section 3.C on what you can do about it. 5. Can you comfortably operate the...
Page 8
9 c. Mechanical safety check routinely check the condition of your bicycle before every ride. Nuts, bolts & straps: make sure nothing is loose. Lift the front wheel off the ground by two or three inches, then let it bounce on the ground. Anything sound, feel or look loose? Do a quick visual and tact...
Page 9
10 handlebar ends: make sure the handlebar grips are secure and in good condition. If not, replace them. Make sure the handlebar ends and extensions are plugged. If not, plug them before you ride. If the handlebars have bar end extensions, make sure they are clamped tight enough so you can’t twist t...
Page 10: 2. Safety
11 2. Safety warning: failure to wear a helmet when riding may result in serious injury or death a. The basics 1. Always wear a cycling helmet which meets the latest certification standards and follow the helmet manufacturer’s instructions for fit, use and care of your helmet. Most serious bicycle i...
Page 11
12 b. Riding safely 1. Observe all local bicycle laws and regulations. Observe regulations about licensing of bicycles, riding on sidewalks, laws regulating bike path and trail use, and so on. Observe helmet laws, child carrier laws and special bicycle traffic laws. It’s your responsibility to know ...
Page 12
13 10. Never carry anything which obstructs your vision or your complete control of the bicycle, or which could become entangled in the moving parts of the bicycle. 11. Never hitch a ride by holding on to another vehicle. 12. Don’t do stunts, wheelies or jumps. They can cause you injury and damage y...
Page 13
14 responsibility to minimize your impact on the environment. Leave things as you found them; and always take out everything you brought in. 9. Be prepared. If something goes wrong while you’re riding off-road, help may not be close. D. Wet weather riding warning: wet weather impairs traction, braki...
Page 14
15 the mounting brackets of front and rear reflectors are often designed as cantilever brake straddle cable safety catches which prevent the straddle cable from catching on the tire tread if the cable jumps out of its yoke or breaks. Warning: do not remove the front or rear reflectors or reflector b...
Page 15
16 f. Downhill or competition biking if you ride downhill at speed or in competition, you voluntarily assume an increased risk of injury or death. When riding downhill, you can reach speeds seen on motorcycles, and therefore face similar hazards and risks. Have your bicycle and equipment carefully i...
Page 16: 3. Fit
17 3. Fit warning: correct fit is an essential element of bicycling safety, performance and comfort. Making the adjustments to your bicycle which result in correct fit for your body and riding conditions requires experience, skill and special tools. Always have your dealer make the adjustments on yo...
Page 17
18 1. Up and down adjustment. Check for correct saddle height (fig. 3): • sit on the saddle; • place one heel on a pedal; • rotate the crank until the pedal with your heel on it is in the down position and the crank arm is parallel to the seat tube. If your leg is not completely straight and just to...
Page 18
19 warning: after any saddle adjustment, be sure that the saddle adjusting mechanism is properly tightened before riding. A loose saddle clamp or seat post binder can cause damage to the seat post, or can cause you to lose control and fall. A correctly tightened saddle adjusting mechanism will allow...
Page 19
20 warning: on some bicycles, changing the stem or stem height can affect the tension of the front brake cable, locking the front brake or creating excess cable slack which can make the front brake inoperable. If the front brake pads move in towards the wheel rim or out away from the wheel rim when ...
Page 20: 4. Tech
21 4. Tech it’s important to your safety, performance and enjoyment to understand how things work on your bicycle. If you have even the slightest doubt as to whether you understand something in this section of the manual, talk to your dealer. A. Wheels 1. Wheel quick release description. The wheel q...
Page 21
22 secondary retention devices fall into two basic categories: a. The clip-on type is a part the manufacturer adds to the front wheel hub or front fork. B. The integral type is molded, cast or machined into the outer faces of the front fork dropouts. Warning: removing or disabling the secondary rete...
Page 22
23 warning: the full force of the cam action is needed to clamp the wheel securely. Holding the nut with one hand and turning the lever like a wing nut with the other hand until everything is as tight as you can get it will not clamp the wheel safely in the dropouts. Caution: if your bike is equippe...
Page 23
24 (5) if the lever cannot be pushed all the way to a position parallel to the fork blade, return the lever to the open position. Then turn the tension-adjusting nut counterclockwise one-quarter turn and try tightening the lever again. (6) re-engage the brake quick-release mechanism to restore corre...
Page 24
25 (5) tighten the quick-release adjusting nut until it is finger tight against the frame dropout; then swing the lever toward the front of the bike until it is parallel to the frame’s chainstay or seatstay and is curved toward the wheel (fig. 7b). To apply enough clamping force, you should have to ...
Page 25
26 (3) if your front fork has a clip-on type secondary retention device, disengage it and go to he next step. If your front fork has an integral secondary retention device, loosen the axle nuts enough to allow wheel removal; then go to the next step. (4) raise the front wheel a few inches off the gr...
Page 26
27 warning: if your bike is equipped with an internal gear rear hub, do not attempt to remove the rear wheel. The removal and re-installation of internal gear hubs require special knowledge. Incorrect removal or assembly can result in hub failure, which can cause you to lose control and fall. D. Ins...
Page 27
28 adjusting the seatpost quick release mechanism. The action of the quick release cam squeezes the seat collar around the seat post to hold the seat post securely in place. Clamping force is controlled by the tension adjusting nut. Turning the tension-adjusting nut clockwise while keeping the cam l...
Page 28
29 brakes are designed to control your speed, not just to stop the bike. Maximum braking force for each wheel occurs at the point just before the wheel “locks up” (stops rotating) and starts to skid. Once the tire skids, you actually lose most of your stopping force and all directional control. You ...
Page 29
30 other hazards and distractions. Everything changes when you ride on loose surfaces or in wet weather. Tire adhesion is reduced, so the wheels have less cornering and braking traction and can lock up with less brake force. Moisture or dirt on the brake pads reduces their ability to grip. The way t...
Page 30
31 1. How a derailleur drivetrain works a. Parts of the drivetrain. If your bicycle has a derailleur drivetrain, the gear- changing mechanism will have: (1) a rear cassette or freewheel sprocket cluster (2) a rear derailleur (3) usually a front derailleur (4) one or two shifters (5) one, two or thre...
Page 31
32 caution: never move the shifter while pedaling backward, nor pedal backwards after having moved the shifter. This could jam the chain and cause serious damage to the bicycle. C. Shifting the rear derailleur. The rear derailleur is controlled by the right shifter. The function of the rear deraille...
Page 32
33 at first, practice shifting where there are no obstacles, hazards or other traffic, until you’ve built up your confidence. If you have difficulties with shifting, the problem could be mechanical adjustment. See your dealer for help. 2. How an internal gear hub drivetrain works. If your bicycle ha...
Page 33
34 e. Pedals some higher performance bicycles come equipped with pedals that have sharp and potentially dangerous surfaces. These surfaces are designed to add safety by increasing adhesion between the rider’s shoe and the pedal. If your bicycle has this type of high-performance pedal, you must take ...
Page 34
35 warning: getting into and out of pedals with toeclips and straps requires skill which can only be acquired with practice. Until it becomes a reflex action, the technique requires concentration which can distract the rider’s attention, causing you to lose control and fall. Practice the use of toec...
Page 35
36 f. Bicycle suspension warning: failure to maintain, check and properly adjust the suspension system may result in suspension malfunction, which may cause you to lose control and fall. Warning: changing suspension adjustment can change the handling and braking characteristics of your bicycle. Neve...
Page 36
37 g. Tires and tubes 1. Tires. Bicycle tires are available in many designs and specifications, ranging from general-purpose designs to tires designed to perform best under very specific weather or terrain conditions. If, once you’ve gained experience with your new bike, you feel that a different ti...
Page 37
38 warning: never inflate a tire beyond the maximum pressure marked on the tire’s sidewall. Exceeding the recommended maximum pressure may blow the tire off the rim, which could cause damage to the bike and injury to the rider and bystanders. Caution: pencil type automotive tire gauges can be inaccu...
Page 38
39 tires. To inflate a presta valve tube using a presta headed bicycle pump, remove the valve cap; unscrew (counterclockwise) the valve stem lock nut; and push down on the valve stem to free it up. Then push the pump head on to the valve head, and inflate. To inflate a presta valve with a schraeder ...
Page 39
40 2. Rebound adjustment. All k2 razorback rear shock units are equipped with a rebound adjustment. Rebound is the movement of the shock unit from a compressed mode to an uncompressed mode. Rebound damping controls the speed at which the shock returns to the uncompressed position. While riding, the ...
Page 40
41 4. Adjustable geometry. All razorbacks offer adjustable geometry. The integrated shock mount comes with an a and a b position. The two positions allow you to set up the bicycle with a 71.8 degree head angle with a 3 inch or 4 inch travel fork. It is also possible to adjust the geometry to your pe...
Page 41
42 c. Adjusting the coil shock preload. (1) a coil-sprung shock’s preload is adjusted by rotating the knurled preload nut that compresses the coil. By gripping the spring as in (fig. 30) and rotating, you can usually perform the adjustment. To begin, loosen the preload completely until the coil is l...
Page 42
43 2. Wheel travel adjustment. The k2 tirade offers three travel options; with two inches of range we call broadband travel. The travel increments will match up to the most popular suspension fork offerings for a truly balanced ride. Position a, as in (fig. 32), will give you 6” of rear wheel travel...
Page 43
44 note: for more information, visit the tech areas of www.K2bike.Com and www.Foxracingshox.Com www.Answerproducts.Com j. Lithium set-up instructions 1. Spring preload adjustment. To receive the best performance from your k2 lithium, it is necessary to adjust the suspension. A. What is sag? “sag” is...
Page 44
45 c. Adjusting the coil shock preload. (1) a coil-sprung shock’s preload is adjusted by rotating the knurled preload nut that compresses the coil. By gripping the spring as in (fig. 30) and rotating, you can usually perform the adjustment. To begin, loosen the preload completely until the coil is l...
Page 45
46 3. Rebound adjustment. All k2 lithium shock units are equipped with rebound adjustment. Rebound is the movement of the shock unit from a compressed mode to an uncompressed mode. Rebound damping controls the speed at which the shock returns to the uncompressed position. While riding, the shock uni...
Page 46
47 (1) measure the shock eye-to-eye (the distance from the center of one mounting bolt to the center of the other mounting bolt). Call this dimension “a.” (2) sit on the bicycle in a normal riding position, weighting both the handlebars and saddle. Have an assistant measure the shock unit eye-to-eye...
Page 47: 5. Service
48 3. Rebound adjustment. The k2 attack 2.0 shock units are equipped with rebound adjustment. Rebound is the movement of the shock unit from a compressed mode to an uncompressed mode. Rebound damping controls the speed at which the shock returns to the uncompressed position. While riding, the shock ...
Page 48
49 • ask your dealer for copies of the manufacturer’s installation and service instructions for the components on your bike, or contact the component manufacturer. • ask your dealer to recommend a book on bicycle repair. • ask your dealer about the availability of bicycle repair courses in your area...
Page 49
50 3. After every long or hard ride: if the bike has been exposed to water or grit; or at least every 100 miles: clean the bike and lightly oil the chain. Wipe off excess oil. Lubrication is a function of climate. Talk to your dealer about the best lubricants and the recommended lubrication frequenc...
Page 50
51 6. Every 25 hours of hard off-road riding or 50 hours of road riding: take your bike to your dealer for a complete checkup. Warning: like any mechanical device, a bicycle and its components are subject to wear and stress. Different materials and mechanisms wear or fatigue from stress at different...
Page 51: 6. K2 Bike Support
52 b. If your bicycle sustains an impact: first, check yourself for injuries, and take care of them as best you can. Seek medical help if necessary. Next, check your bike for damage, and fix what you can so you can get home. Then, take your bicycle to your dealer for a thorough check. Warning: a cra...