Summary of Combi B 30
Page 1
Combi b 30 with metal input unit operating instructions en.
Page 2
Version 2013-08-10 page 26 of 48 operating instructions 82132/3xxx cb 30 table of contents 1 important notes ................................................................................................................................................ 28 2 glossary of abbreviations and terms ........
Page 3
Version 2013-08-10 page 27 of 48 operating instructions 82132/3xxx - combi b 30 11.3 changing master code using the key (p) ................................................................................................................ 44 11.4 resetting the lock (p0) ..................................
Page 4
Version 2013-08-10 page 28 of 48 operating instructions 82132/3xxx cb 30 1 important notes before the start-up of the lock read these operating instructions carefully and observe the following notes: the enclosed inspection key allows full access to the lock and its configurations even in case of co...
Page 5
Version 2013-08-10 page 29 of 48 operating instructions 82132/3xxx - combi b 30 2 glossary of abbreviations and terms - code: numerical sequence of 8 digits for identification of the operator consisting of id and pin. - id: fixed 2-digit operator number. - pin: freely selectable 6-digit combination ...
Page 6
Version 2013-08-10 page 30 of 48 operating instructions 82132/3xxx cb 30 3 the icons used in the instructions icon meaning warning important note icon for the 2-digit code id (also refer to chapter 2) oder icon for individual number keys for the code input action performed action not performed rotat...
Page 7
Version 2013-08-10 page 31 of 48 operating instructions 82132/3xxx - combi b 30 4 lock system: input unit and lock the entire lock system consists of a visible input unit and the lock installed in the secure storage unit. All programmed codes and functions are saved only in the lock and, thus, in th...
Page 8
Version 2013-08-10 page 32 of 48 operating instructions 82132/3xxx cb 30 5 overview of authorizations the authorizations of individual operators are as follows: operator id code designation authorization - inspection key - opening without od/ost and without guard time - assigning of a new master cod...
Page 9
Version 2013-08-10 page 33 of 48 operating instructions 82132/3xxx - combi b 30 7 overview of the possible signals event when signal pressing the key (e.G. Code input) with every key stroke 1 x code valid (code-correct message) correct input after pressing enter 2 x and 2 x error message (e.G. Code ...
Page 10
Version 2013-08-10 page 34 of 48 operating instructions 82132/3xxx cb 30 8 start-up of the lock the lock installation as well as cabling and the first battery installation are described in the installation manual. As long as the lock system has not been put into operation, it can be opened using the...
Page 11
Version 2013-08-10 page 35 of 48 operating instructions 82132/3xxx - combi b 30 9.1 changing master code (p) after modification of the master code the previous master code is no longer valid. The function of the new master code must be checked by opening the lock with the secure storage unit open (s...
Page 12
Version 2013-08-10 page 36 of 48 operating instructions 82132/3xxx cb 30 9.2.2 blocking the user codes or courier codes (p4) after blocking, the code cannot be used anymore until it is released again (see chapter 9.2.3) in contrast to deletion, after blocking the code remains unchanged in the lock a...
Page 13
Version 2013-08-10 page 37 of 48 operating instructions 82132/3xxx - combi b 30 9.2.5 code status query (p6) the status of any code (active, blocked or inactive resp. Deleted) can be requested in this query program. Neither the codes nor their statuses are changed by this operation. The statuses of ...
Page 14
Version 2013-08-10 page 38 of 48 operating instructions 82132/3xxx cb 30 description 1. Press and enter the valid master code and (00 = id, x = valid 6-digit combination for the master) 2x 3x 3x 2 press and 2x 3x 3x 3. Enter and 2x 2x 3x 3x table 15: deleting opening delay and opening standby time 9...
Page 15
Version 2013-08-10 page 39 of 48 operating instructions 82132/3xxx - combi b 30 9.5 programming silent alarm (p8) a silent alarm is triggered by a special code input. The message in question is an alarm message which initiates the lock using an alarm output, the lock can still be opened during this....
Page 16
Version 2013-08-10 page 40 of 48 operating instructions 82132/3xxx cb 30 description 1. Press and enter the valid master code and (00 = id, x = valid 6-digit combination for the master) 2x 3x 3x 2. Press and 2x 3x 3x table 20: acknowledging the take-off contact message 10 lock functions for all user...
Page 17
Version 2013-08-10 page 41 of 48 operating instructions 82132/3xxx - combi b 30 the running opening delay can be canceled any time by pressing twice. If the incorrect code signal is output after the code input, the entry must be repeated completely. After 3 incorrect inputs the lock switches to the ...
Page 18
Version 2013-08-10 page 42 of 48 operating instructions 82132/3xxx cb 30 opening process: description 1. Enter a modified valid opening code as an alarm code and (id = 00 to 30 or 95, x = the first 5 positions of the programmed 6-digit combination for the corr. Id number, y = increased by 1 or decre...
Page 19
Version 2013-08-10 page 43 of 48 operating instructions 82132/3xxx - combi b 30 10.8 opening with activated additional functions the lock has special additional functions (only one of them respectively) which can be set only using the optional pc software. If one of these functions is activated, the...
Page 20
Version 2013-08-10 page 44 of 48 operating instructions 82132/3xxx cb 30 11.2 closing using the key turn the key to the stop counterclockwise through approx. 150°, remove it and secure against unauthorised access (not inside the secure storage unit). Then insert the square shaft with the end of the ...
Page 21
Version 2013-08-10 page 45 of 48 operating instructions 82132/3xxx - combi b 30 description 1. Open the lock using the key (see chapter 11.1) 2. Press and 2x 3x 3x 3. Press and 2x 2x 3x 3x 4. Close the lock again by means of the key (11.2) and mount the rotary handle (11.1) table 28: resetting the l...
Page 22
Version 2013-08-10 page 46 of 48 operating instructions 82132/3xxx cb 30 13.1 undervoltage indication w and the battery must be replaced promptly (see chapter13.2). As soon as the undervoltage indication is displayed, the lock can still be opened, but no reprogramming is possible until after the bat...
Page 23
Version 2013-08-10 page 47 of 48 operating instructions 82132/3xxx - combi b 30 13.3 permanent power supply if necessary, along with the battery power supply the lock can also be supplied with voltage permanently. The following options are available for this purpose: a) power supply via the intruder...
Page 24
Version 2013-08-10 page 48 of 48 operating instructions 82132/3xxx cb 30 15 notes kaba mauer gmbh frankenstrasse 8-12 d-42579 heiligenhaus, germany codes activated blocked released deleted master user 01 user 02 user 03 user 04 user 05 user 06 user 07 user 08 user 09 user 10 user 11 user 12 user 13 ...