1. DL manuals
  2. Kaba
  3. Door locks
  4. E-PLEX 3X00 SERIES
  5. Installation Instructions Manual

Kaba E-PLEX 3X00 SERIES Installation Instructions Manual

Manual is about: E-PLEX 3X00 SERIES NARROW STILE LOCK

Summary of E-PLEX 3X00 SERIES

  • Page 1

    Installation instructions e-plex ® 3 x 00 series narrow stile lock.

  • Page 2: Table Of Contents

    Table of contents e-plex 3x65 deadlatch/exit mortise model e-plex 3x66 deadbolt/swing bolt mortise model this lock is designed to function with new or existing adams rite ® hardware for deadlatch, deadbolt, and exit applications. These adams rite hardware models (1850, 1950, 4500, 4700, 4900, ms1850...

  • Page 3: Tools Required

    Tools required • power drill with 3 ⁄ 8 ” (10mm) drill bit • tape • center punch or awl • hex allen wrench set • phillips head screwdriver • small flat blade screwdriver • safety glasses a. Door preparation—remove existing outside hardware a-1 remove any existing outside hardware such as lever entry...

  • Page 4: Kaba E-Plex

    4 kaba e-plex ® 3x00 series limited warranty kaba access control warrants this product to be free from defects in material and workmanship under normal use and serv- ice for a period of three (3) years. Kaba access control will repair or replace, at our discretion, e-plex 3000 series locks found by ...

  • Page 5: Stile Preparation

    5 b. Stile preparation b-1 install the kaba cam plug d1 or d2 into the deadlatch or deadbolt. Face of cam plug must be flush or below the surface of the stile, make sure set screw is snug but do not tighen it yet. (see figure 2 on page 3). Note: refer to the adams rite cam plug instructions for righ...

  • Page 6: C. Lock Preparation

    6 c. Lock preparation c-1 on deadlatch model only, remove handing screw (fig 4): caution: the appropriate handing screw must be removed for proper lock function after installation. Inside the battery compartment, the lock comes with both handing screws installed. Based on the door application handin...

  • Page 7

    K a b a a c c e s s c o n t r o l 2 9 4 1 in d ia n a a v e n u e w in s t o n -s a l e m , n c 2 7 19 9 -3 7 7 0 no po s t a ge ne ce s s ar y if mailed in the united s t a te s b u s i n e s s r e p l y m a il f ir s t -c l a s s m a il p e r m it n o . 15 6 3 p o s t ag e w il l b e p a id b y a ...

  • Page 8

    T hank y ou for pur chasing our pr oduct . In or der to pr o tect y our in v e s tmen t and to enable us to be tt er s e r v e y o u in th e fu tu re , p le a s e fi ll o u t th is re g is tr a ti o n c ar d and r e turn it to k ab a a c c e s s c on tr ol, or r egis ter online at www .K ab aac c e ...

  • Page 9

    9 notes.

  • Page 10

    10 notes.

  • Page 11

    11 1. Change master code and place lock in passage mode. Step 1. Enter # to start the programming mode step 2. Enter the 8-digit factory default master code: 1 2 3 4 5 6 7 8 # step 3. Enter change master code code command: 0 0 0 # step 4. Enter new 8-digit master code: 8 7 6 5 4 3 2 1 # step 5. Reen...

  • Page 12

    12 5. Orient the lock to keep the key override cam clear and insert the new cylinder (fig 11). 6. Insert the new cylinder all the way until the ms cam bottoms out on the gear pack. Once it bottoms out, back rotate the cylinder until the plug is at the six o’clock position. (fig’s 12, 13, and 14) 7. ...

  • Page 13: D. Lock Installation

    D. Lock installation (see figs. 15a, b, and c) note: this step is to be done with the door open. D-1 from the screw pack, place the two mounting bushings (b) into the upper, interior 3 ⁄ 8 ” holes. D-2 deadlatch: place one end of the square spindle into the upper hole of the lock (marked ”l” on back...

  • Page 14

    14 d-7 locks with levers–based on the required handing of the lock as deter- mined in section c, install the lever (h) and lever cap (g) using torx screws (f) and provided torx wrench. Secure lever cap (g) with allen set screw using supplied allen wrench. (see figure 16) d-8 check for proper operati...

  • Page 15: Programming:

    15 e. Standard operating procedures e-1 this lock is equipped with a standard break away clutch. In the “home position,” the lever or thumb turn is horizontal to the floor with the ability to “break away” down to a detented position as the lever or thumb turn is rotated. This “break away” action pro...

  • Page 16

    Kaba access control 2941 indiana avenue winston-salem, nc 27105 usa tel: (800) 849-8324 (336) 725-1331 fax: (800) 346-9640 (336) 725-3269 www.Kabaaccess.Com www.E-plexlock.Com pkg3215 1107.