Summary of E-Plex 5X10
Page 1
5x10 exit trim models installation instructions.
Page 2: Table Of Contents
2 table of contents assembly drawing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 tools required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....
Page 3
3 e-plex 5x10 exit trim model the e-plex exit trim lock is adapt- able to a wide variety of the more popular exit devices on the market today. No tools are required to reverse handing, and the spring loaded tailpiece drive automatical- ly adjusts to door thicknesses from 1 3 ⁄ 4 " to 2 1 ⁄ 8 ". A do...
Page 4: Tools Required
4 tools required • safety glasses • electric drill (variable speed) • awl or center punch • 2 1 ⁄ 8 " (54 mm) hole saw pilot drill • 3 ⁄ 8 " (25 mm) hole saw pilot drill • hammer • phillips head screwdriver • small flat blade screwdriver operational note: the e-plex exit trim lock is almost identica...
Page 5
5 a. Door preparation - exit device a-1 for new installations (existing installations proceed to step a-2): for new installations, all mounting hardware for the actual exit device should be acquired from the exit device supplier. All necessary hardware to mount the e-plex exit trim is included in th...
Page 6: C. Install Exit Device:
6 b. Door preparation – e-plex exit trim b-1 for new installations (existing installations proceed to step b-2): place paper template (e) (supplied) onto the inside of the door and align with the centerlines. Mark the location of the e-plex exit trim mounting holes. Drill the four 3 ⁄ 8 " (10 mm) (b...
Page 7: D. Door Thickness
7 d. Door thickness the e-plex exit trim drive unit (a) has a spring loaded tailpiece (b) and is preassembled to accom- modate standard door thickness from 1 3 ⁄ 4 " to approximately 2 1 ⁄ 8 " for most applications. For doors up to 2 1 ⁄ 4 " inches it may be necessary to add a spacer to increase the...
Page 8: Kaba Simplex
Kaba simplex ® /e-plex ® 5x00 series limited warranty kaba access control warrants this product to be free from defects in material and workmanship under normal use and service for a period of three (3) years. Kaba access control will repair or replace, at our discretion, 5000 series locks found by ...
Page 9
K a b a a c c e s s c o n t r o l 2 9 4 1 in d ia n a a v e n u e w in s t o n -s a l e m , n c 2 7 19 9 -3 7 7 0 n o p o s t a g e n e c e s s a r y if m a il e d in t h e u n it e d s t a t e s b u s i n e s s r e p l y m a il f ir s t -c l a s s m a il p e r m it n o . 15 6 3 p o s t a g e w il l...
Page 10
T h a n k y o u fo r p u r c h a s in g o u r p r o d u c t. In o r d e r to p r o te c t y o u r in v e s tm e n t a n d to e n a b le u s to b e tt e r s e r v e y o u in th e fu tu re , p le a s e fi ll o u t th is re g is tr a ti o n c a r d a n d r e tu r n it to k a b a a c c e s s c o n tr o ...
Page 11: Notes
Notes.
Page 12: Kil Cylinder
A b c e d f 8 g. Changing key-in-lever cylinder on key-in-lever models of the e-plex, the outside lever comes preassembled with kaba’s key-in-lever cylinder (kaba 1599). To use a different key-in-lever cylinder follow remaining steps in this section. G-1 remove kil (key-in-lever) cylinder (a) from t...
Page 13
9 h. Installing / removing outside lever (key-in-lever models only, for interchangeable and removable cores proceed to section i) note: installing levers to the unit assemblies before mounting the unit assemblies may ease initial installation. H-1 make certain the lever catch is up as shown (c). Pos...
Page 14
10 i-2 insert the outside lever (b) until it is flush to the outside unit assembly (a). To secure the outside lever, insert the release tool (d) (or screwdriver) into the outside lever as shown, and slide the lever catch down until it clicks. Make certain lever is attached before installing the core...
Page 15
11 i-7 using two pairs of pliers, break the tailpiece to the desired length of the intended application by holding one pair of pliers on the good side of the score mark and a second pair on the other side of the score mark. Slowly move the 2nd pair of pliers up and down until the unneeded portion of...
Page 16
12 j-4 insert the lectrobolt through the red battery mounting plate hole marked with the lightning bolt symbol. For now, only partially tighten the lectrobolt enough to hold the outside unit assembly and the battery mounting plate in place on the door. J-5 insert the two mounting bushings (f) into t...
Page 17
13 warning: do not install a 9v battery. This eplex lock operates on 4 alkaline only aa batteries (6v). A 9v will ruin the electronics in the lock and void the warranty. K-3 remove the four depleted batteries and install four new alkaline (only) aa batteries. Ensure that each battery is installed in...
Page 18: M. Reset Function
14 m. Reset function warning: when the lock is reset, all existing authorization and access codes are deleted, and the lock is configured to the factory default lock settings. The master code becomes 1,2,3,4,5,6,7,8. If the master code is lost or forgotten and the number has not been recorded, the l...
Page 19: Notes
15 notes.
Page 20
Kaba access control 2941 indiana avenue winston-salem, nc 27105 usa tel: (800) 849-8324 (336) 725-1331 fax: (800) 346-9640 (336) 725-3269 www.Kabaaccess.Com www.E-plexlock.Com pkg3055 0608.