1. DL manuals
  2. Kaba Mas
  3. Locks
  4. X-10
  5. Operating Instructions Manual

Kaba Mas X-10 Operating Instructions Manual

Manual is about: HIGH SECURITY ELECTRONIC LOCK Type 1F

Summary of X-10

  • Page 1

    Operating instructions x-10 tm type 1f high security electronic lock.

  • Page 2: Table of Contents

    Table of contents introduction 1 lock serial number location 1 dialing the x-10 2 dialing methods 2 to power the lock 2 dialing a...

  • Page 3: Introduction

    1 introduction the x-10™ uses sophisticated computer security and makes dialing much easier than that of traditional combination locks the microprocessor in the lock recognizes a number as part of a combination when you change dialing direction (see the section on dialing the x-10) note: the lock is...

  • Page 4: Dialing The X-10

    2 dialing the x-10 dialing methods the user should dial with full wrist turns this helps the x-10 distinguish between human and robotic dialers note: if an incorrect combination is dialed or if the elapsed combination dialing time is less than 10 seconds, a lightning bolt will appear when you dial r...

  • Page 5

    3 if you pass your target number when dialing: example a: target number = 25 if you pass your target number by 4 or more, continue dialing until you reach the target number again example b: target number = 25 if you pass the target number by no more than 3 numbers, you may continue dialing until you...

  • Page 6: Open And Close The X-10

    4 open and close the x-10 (factory combination) if you have not read the section on “dialing the x-10”, it is important that you do so before proceeding note: the lock is shipped preset to operate in the single combination mode with a default factory combination of 50-25-50. To open the lock (using...

  • Page 7: X-10 Lock Setup

    5 figure 2 - change key x-10 lock setup setting up the x-10 lock for operation involves selecting both the operating mode and the combination(s) note: the lock is shipped preset to operate in the single combination mode with a factory combination of 50-25-50. Before you can set a new combination, yo...

  • Page 8

    6 2 release the container locking bolts if necessary (different containers will have different release mechanisms) 3 insert the change key into the change key holes on the back of the lock (see figure 3) 4 dial left (ccw) until the change key appears in the upper right hand corner of the display cau...

  • Page 9

    7 if selection = 01, single combination mode: 1 dial right (cw) until the symbol ec (enter combination) appears 2 dial the new combination as if dialing a combination to open the lock; ie, left (ccw) to dial the first number, right (cw) to dial the second number, left (ccw) to dial the third number ...

  • Page 10

    8 5. Dial right (cw) briskly. The new combination will be displayed two times, two digits at a time, followed by po (pull out change key). Note: if the correct combination is not displayed, you may pull out the change key and the lock will allow you to reset the combination. You must pull out the ch...

  • Page 11: Using The X-10

    9 using the x-10 if you have not read the section on “dialing the x-10”, it is important that you do so before proceeding single combination mode in this mode the x-10 functions much like a standard combination lock. It will open any time the three-number combination is correctly dialed. 1. Dial le...

  • Page 12

    10 5. Dial right (cw). After op with a right arrow (open right) is displayed, continue dialing to the right to retract the lock bolt. Note: if at any time the dial remains stationary for more than 40 seconds, the computer will reset (lcd will go blank) requiring the operator to redial the entire com...

  • Page 13

    11 to lock up (lu) supervisory operator: 1 dial left (ccw) until lock is “powered” 2 dial the supervisory combination as if dialing a combination to open the lock; ie, left (ccw) to dial the first number, right (cw) to dial the second number, left (ccw) to dial the third number example: combination ...

  • Page 14

    12 audit features and firmware level of the lock the x-10 lock tracks the number of successful openings for the lifetime of the lock; it tracks the number of consecutive unsuccessful attempts, it will alert you upon lock power up if there have been 3 or more consecutive unsuccessful attempts to open...

  • Page 15: Guide To Symbols

    13 blank display lock is powered down op open right lightning bolt incorrect combination dialed lightning bolt with error count incorrect combination dialed xx times. (the error count is only displayed when there have been 3 or more consecutive unsuccessful attempts.) flashing lighting bolts lock in...

  • Page 16

    Document number 5390512 rev b - 10/13 kaba mas llc 749 w. Short street, lexington, ky 40508 usa phone: 859-253-4744 fax: 859-255-2655 technical support: 800-950-4744 www.Kaba-mas.Com notice: the information in this manual is subject to change without notice and does not represent a commitment on the...