Summary of SIMPLEX 3000 NARROW STILE
Page 1
Installation instructions simplex ® 3000 narrow stile.
Page 2: Table Of Contents
2 table of contents package contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 tools required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 a. Combination lock assembly...
Page 3
3 a. Combination lock assembly a-1 cylinder installation: remove interposer assembly (a) by removing one round head screw and one flat head screw (see figure 1-1). A-2 install mortise cylinder by turning cylinder until cylinder cam (e) contacts lock-in plate (b) (see figure 1-1). Turn cylinder to th...
Page 4: Mounting Lock To Stile
4 b. Mounting lock to stile b-1 place combination lock assembly over lock-in studs and slide downward until a stop position is attained (approximately 1 ⁄ 8 " of movement) (see figure 2-1). The top of the lock housing and drive assembly should be flush when properly positioned. Note: before closing ...
Page 5
5 b-2 fix two each 10-24 x 2 1 ⁄ 8 " long round head machine screws (a) as shown (see figures 2-1 & 2-2). Using the df-59 key, thread the control lock assembly (b) into the combination change sleeve (c) df-59 (see figure 2-2) until trim plate is snug against stile. The key can only be removed in ver...
Page 6
6 c. Operating instructions note: all locks are shipped with the following combination: #2 and #4 pushed at the same time, then #3. For proper security, the factory set code must be changed at the time of installation. C-1 gaining access by combination code a. To clear any previously depressed code ...
Page 7
7 c-4 latch holdback a. Insert cylinder key into cylinder on combination lock side of the door. Turn the key in a clockwise direction to the stop position, retracting the latch fully (see figure 3-6). Hold the key in that position and turn the thumb turn to the left (counterclockwise). Bring the key...
Page 8: Kaba Simplex
8 kaba access control warrants this product to be free from defects in material and workmanship under normal use and service for a period of one (1) year. Kaba access control will repair or replace, at our discre- tion, simplex locks found by kaba access control analysis to be defec- tive during thi...
Page 9
K a b a a c c e s s c o n t r o l 2 9 4 1 in d ia n a a v e n u e w in s t o n -s a l e m , n c 2 7 19 9 -3 7 7 0 n o p o s t a g e n e c e s s a r y if m a il e d in t h e u n it e d s t a t e s b u s i n e s s r e p l y m a il f ir s t -c l a s s m a il p e r m it n o . 15 6 3 p o s t a g e w il l...
Page 10
T h a n k y o u f o r p u r c h a s in g o u r p r o d u c t. I n o r d e r t o p r o te c t y o u r i n v e s tm e n t a n d t o e n a b le u s t o b e tt e r s e r v e y o u in t h e f u tu re , p le a s e f ill o u t th is r e g is tr a ti o n c a r d a n d r e tu r n i t to k a b a a c c e s s c...
Page 11
9 d. Combination change information important: read all instructions before beginning. D-1 changing combinations: in order to change an existing combination, you must: 1. Have a df 59 key 2. Know the existing combination 3. Have lock set for pushbutton access to retract latch 4. Have a small flat 1 ...
Page 12
10 d-9 turn the thumb turn clockwise to the stop position, assuring the latch is retracted (see figure 4-3). Release thumb turn. You should not be able to turn the thumb turn unless you have depressed the buttons of your newly entered combination. The new combination is now programmed in the lock. D...
Page 13
11 e. Resetting an unknown combination remove the combination chamber, held by 2 screws, from the lock. To remove the 3-sided dust cover marked "kaba,” “simplex," etc. Place the combination chamber in the position to the right. E-1 place a small screwdriver on the edge of the 3-sided dust cover and ...
Page 14
12 for technical assistance please call 1.800.849.Tech (8324) or 336.725.1331 e-9 depress the lockout slide (g) at the top of the chamber and release. (looks like one end of a spark plug) (see figure 5-4). E-10 using pliers or equivalent, rotate the control shaft (d) counterclockwise to clear the ch...
Page 15
13 notes.
Page 16
Kaba access control 2941 indiana avenue winston-salem, nc 27105 usa tel: 800.849.8324 or 336.725.1331 fax: 800.346.9640 or 336.725.3269 www.Kabaaccess.Com pkg2586 0709.