Kaba Simplex 5000 Installation Instructions Manual

Summary of Simplex 5000

  • Page 1

    Kaba access control 2941 indiana avenue winston-salem, nc 27105 usa tel: (800) 849-8324 (336) 725-1331 fax: (800) 346-9640 (336) 725-3269 www.Kabaaccess.Com pkg2842 0407 5000 cylindrical installation instructions.

  • Page 2

    Tools required • safety glasses • electric drill (variable speed) • awl or center punch • 2 1 ⁄ 8 " (54 mm) hole saw pilot drill • 1" (25 mm) hole saw pilot drill • 1 ⁄ 4 " (7 mm) drill bit • 1" (25 mm) wood chisel • hammer • phillips head screw driver • small flat blade screwdriver inside lever mou...

  • Page 3

    A. Door preparation a-1 place paper template (supplied) onto door and mark for holes. Drill the four 1 ⁄ 4 " (7 mm) holes first. Next drill the 2 1 ⁄ 8 " (54 mm) cross bore hole. Drill the 1" (25 mm) hole last. A-2 for models 5041 & 5051 only. When installing model 5021, skip to step a-4. Passage fe...

  • Page 4

    5 f-2 slide the drive hub (a) into the drive sleeve (b) until the inside unit assembly (c) rests flush against the door. F-3 for standard door thickness 1 5 ⁄ 8 " (41 mm) to 2" (51 mm), secure the outside and inside unit assemblies to the door by using four 2 7 ⁄ 8 " (73 mm) screws (d) (supplied) in...

  • Page 5

    7 i-1 make certain the lever catch is up as shown (c). The lever catch should be flush around the outer diameter of the outside driver. Make certain the lever sleeve (f) is rotated to properly mate with the outside lever/knob. I-2 insert one of the supplied keys (a) into the outside lever/knob (b) a...

  • Page 6

    Kaba simplex ® /e-plex ® 5x00 series limited warranty kaba access control warrants this product to be free from defects in material and workmanship under normal use and service for a period of three (3) years. Kaba access control will repair or replace, at our discretion, 5000 series locks found by ...

  • Page 7

    11 notes t hank y ou for pur chasing our pr oduct . In or der to pr o tect y our in v e s tmen t and to enable us to be tt er s e r v e y o u in th e fu tu re , p le a s e fi ll o u t th is re g is tr a ti o n c ar d and r e turn it to k ab a a c c e s s c on tr ol, or r egis ter online at www .K ab...

  • Page 8

    11 j-7 insert the assa/medeco/yale tailpiece (e) vertically into the outside lever/knob as shown. Make certain that you rotate the tailpiece slightly so that it will align with the interchangeable/ removable core. Insert the interchangeable/ removable core into the outside lever/knob. Note: to remov...

  • Page 9

    13 interior combination change m-3 unscrew special torx screw from inside housing using supplied torx wrench. Enter your existing combination, and depress and release the “enter” button. Insert longer end of the same torx wrench through the opening until it engages with the mating part. Turn wrench ...

  • Page 10

    15 o-3 resetting and recovery of current code to reset the code gears (a), each one of the 5 “l” shaped legs (b) of the unlocking slide (c) must engage snugly with the corresponding code gear pocket (d) next to it. Position the chamber in one hand, as shown. Hold chamber by the top screw tab (e) and...

  • Page 11

    17 p. Trouble shooting symptom possible cause remedy 1. The outside lever/knob always retracts the latch after depressing and releasing the “enter” button only (without combination). 2. The outside lever/knob will not go completely inside the outside lock assembly. 3. Correct combination is depresse...

  • Page 12

    19 18 notes notes.