Kaise KU-2600 Instruction Manual
FOR SAFETY MEASUREMENTS!!
WARNING
INTRODUCTION
2. SPECIFICATIONS
3. NAME ILLUSTRATION
4. SAFETY PRECAUTIONS
1. UNPACKING AND INSPECTIONS
(23℃±5℃、＜80％RH in non-condensing)
Σ
1
2
3
4
To prevent an electrical shock hazard to the operator and/or damage to the
instruments, read this instruction manual carefully before using the Digital
Multimeter. WARNINGS with the symbol on the Digital Multimeter and
this instruction manual are highly important.
Important Symbols
The symbol listed in IEC 61010-1 and ISO 3864 means "Caution
(refer to instruction manual)".
WARNING : The symbol in this manual advises the user of an
electrical shock hazard that could result in serious injury or even
death.
CAUTION : The symbol in this manual advises the user of an
electrical shock hazard that could cause injury or material damages.
KU-2600 is designed to comply with CAT Ⅱ 600V. But, do not measure High
Power Line of more than 3kVA power. High Power Line sometimes includes
High Surge Voltage that could possibly induce dangerous arcs of explosive
short in the instrument and could result in serious injury to the operator. Even
if it is Low Power Line, use extreme care when measuring high voltage.
Thank you for purchasing KAISE "MODEL KU-2600 DIGITAL MULTIMETER".
To obtain the maximum performance of this instrument, read this Instruction
Manual carefully, and take safe measurement.
Inspect the instrument and acessories for transport damage. If any damage or
missing items are found, ask your local dealer for replacement.
Confirm that the following items are contained in the package.
2-1. GENERAL SPECIFICATIONS
2-2. MEASUREMENT SPECIFICATIONS
1. Digital Multimeter and Test Leads
2. Two 1.5V R6P Batteries (Installed and spare)
3. Two Spare Fuses (0.5A/250V, 10A/250V)
4. Holster
5. Instruction Manual
1. DISPLAY (LCD)
a. Numerical Display : 4000 count LCD, 12mm high
b. Units and Symbols :
2. OPERATING PRINCIPLE : ⊿ conversion
3. RANGE SELECTION : Auto-Ranging / Range Hold
4. SAMPLING RATE : 2 times per second
5. POLARITY : Auto-Polarity ("ー"symbol appears in minus)
6. OVERRANGE INDICATION : "OL" symbol appears. (excluding DC/AC 600V)
7. DIFFERENCE MEASUREMENT (Zero Adjustment) : Press REL△ Key to
make Difference Measurement and Zero Adjustment.
8. DISPLAY HOLD : Press HOLD Key.
9. BATTERY WARNING : symbol appears when battery voltage goes down
below approx. 2.4V.
10. OPERATING TEMPERATURE & HUMIDITY : 0℃ to 40℃, less than 75％ RH
in non-condensing.
11. STORAGE TEMPERATURE & HUMIDITY : −20℃ to 60℃ less than 80％
RH in non-condensing.
12. POWER SUPPLY : Two 1.5V R6p Batteries.
13. POWER CONSUMPTION : 4.5mW typically.
DIGITAL
MULTIMETER
KU-2600
INSTRUCTION MANUAL
1. LCD
2. FUNCTION Switch
3. SELECT Key ( / or DC/AC selection)
4. RANGE Key
5. REL△ Key
6. HOLD Key
7. RESET Key
8. Hz/Duty Key
14. BATTERY LIFE : 150 hours continuous operation.
15. AUTO POWER OFF : Power turns off automatically in 15 minutes after any
switch operation.
16. DIELECTRIC STRENGTH : 3.7kV rms for one minuite between input
Terminal and Cases.
17. FUSES :
18. OVERLOAD PROTECTION :
a. V : 1000V DC or 750V AC rms max. for 1 minute.
(400mV Range is 500V rms )
b. Ω/ / / : 250V rms max. for 1 minute.
19. DIMENSIONS & WEIGHT : 155×75×29 mm, 180g
20. SAFETY LEVEL : IEC-61010-1, Overvoltage CAT.Ⅱ 600V, CATⅢ300V.
21. ACCESSORY : One Pair of Test Leads, Batteries (Installed), Carrying Case,
Instruction Manual
22. OPTIONAL ACCESSORY : 940 Alligator Clips.
− ＋
− ＋
mV, V, Hz, ％, Ω, kΩ, MΩ, nF, μF, , , mA, A,
REL△, , H , OL, AUTO, AC, DC, − and decimal point.
mA Function : Fast Active 0.5A/250V, 5×20mm
10A Function : Fast Active 10A/250V, 6×30mm
9. DC Current ( mA / A )
0.0％
〜
99.9％
0.1％
1V RMS
±
0.2%rdg±2dgt
250V
AC rms
4. Duty Cycle ( ％ )
Range
Resolution
Accuracy
Max. Input
Voltage
Input
Sensitivity
400.0Ω
≒
0.44V
≒
1m sec
less than 50Ω
250V
DC/AC rms
7. Continuity Tests ( )
Range
Buzzer Sound
Overload
Protection
250V
DC/AC rms
250V
DC/AC rms
Overload
Protection
Overload
Protection
Open Circuit
Voltage
Response
Time
4.000V
≦
1.5V
≦
0.5mA
6. Diode Tests ( )
Range
Accuracy
8. Capacitance ( )
400.0 Ω
4.000kΩ
40.00kΩ
400.0kΩ
4.000MΩ
40.00MΩ
0.1 Ω
1 Ω
10 Ω
100 Ω
1 kΩ
10 kΩ
≒
0.44V
±
1.8%rdg±3dgt
±
5.0%rdg±3dgt
5. Resistance ( Ω )
Range
Resolution
Accuracy
Open Circuit
Voltage
Open Circuit
Voltage
Test
Current
±
1.0%rdg±3dgt
0.1nF〜40nF
40nF〜40μF
40μF〜200μF
0.001nF〜nF
nF〜μF
μ
F
±
5.0%rdg±5dgt
±
3.0%rdg±5dgt
±
4.0%rdg±5dgt
≒
1.2V
Range
Resolution
Accuracy
Test
Current
10. AC Current ( 〜mA / 〜A )
400.0mV
4.000 V
40.00 V
400.0 V
600 V
100μV
1mV
10mV
100mV
1 V
400.0 mV
4.000 V
40.00 V
400.0 V
600 V
1mV
10mV
100mV
1 V
≧
100MΩ
≒
10MΩ
±
1.0%rdg±4dgt
600V DC
1. DC Voltage ( V )
Range
Resolution
Accuracy
Max Input
Voltage
Max Input
Voltage
Input
Impedance
±
0.5%rdg±4dgt
≒
10MΩ
600V
AC rms
2. AC Voltage ( 〜V )
Range
Resolution
Accuracy
Input
Impedance
±
1.2%rdg±5dgt
±
4.0%rdg±8dgt
±
1.5%rdg±5dgt
Frequency Scope :1Hz〜1kHz
Overload Protection : 250V DC/AC rms
3. Frequency ( Hz )
9.999Hz
〜9.999MHz
1V RMS
0.01Hz
〜1.0kHz
±
0.2%rdg
±1dgt
250V
AC rms
Range
Resolution
Accuracy
Max. Input
Voltage
Input
Sensitivity
Frequency Response : 50Hz~500Hz. 500Hz~1000Hz : ±3.5%rdg±5dgt.
*400.0mV Range : 5mV~400mV.
0.1 mV
40.00 mA
400.0 mA
10.00 A
10μA
100μA
10 mA
200mV
max.2.0V
1.0V
Range
Resolution
Voltage
Drop
Accuracy
400mA
10A（within15sec.）
40.00mA, 400.0mA : 0.5A/250V Fuse Protected
10.00A : 10A/250V Fuse Protected
40.00mA, 400.0mA : 0.5A/250V Fuse Protected
10.00A : 10A/250V Fuse Protected
±
2.5％rdg±4dgt
±
2.0％rdg±4dgt
40.00 mA
400.0 mA
10.00 A
10μA
100μA
10 mA
200mV
max.2.0V
1.0V
Range
Resolution
Voltage
Drop
Accuracy
400mA
10A（within15sec.）
±
3.0％rdg±5dgt
±
2.5％rdg±5dgt
NOTE :
NOTE :
Max. Input Voltage
Max. Input Voltage
Direct Current
Alternative Current (AC)
Minus Symbol when polarity is minus
Units of Voltage
Unit of Frequency
Unit of Duty Cycle
Units of Resistance
Units of Capacitance
Diode Tests
Continuity Tests
Auto-ranging
Display Hold
Difference Measurements
Battery Warning Symbol
：
：
：
：
：
：
：
：
：
：
：
：
：
：
−
mV, V
Hz
％
Ω
, kΩ, MΩ
nF, μF
AUTO
H
REL
HOLD Key
REL Key
LCD
Hz / DUTY Key
SELECT Key
RANGE Key
RESET Key
10A Terminal
Test Leads
Test Prods
Test Plugs
mA Terminal
COM Terminal
FUNCTION SWITCH
VΩHz Terminal
( )
DC ( )
AC (〜)
− ＋
RS232
AC
DC
AUTO
H
REL
nmFVA
％
KMΩH
z
μ
COM
mA
VΩHz
10A
FUSED
500mA MAX
FUSED
10A/15sec MAX
600V MAX
300V
MAX
Auto Power OFF
OFF
OFF
V
Hz
〜
V
m
A
A 〜
〜
〜
〜
KU-2600
CAT.
SELECT
RANGE
REL
HOLD
Hz/DUTY
RESET
− ＋
RS232
AC
DC
AUTO
H
REL
nmFVA
％
KMΩH
z
μ
fig.1
Set FUNCTION Switch to desired position.
Just press RANGE Key several times to select a desired range watching the
position of decimal point. The decimal point moves from the lowest range to
the highest range and circulates with each press.
When taking voltage, resistance or mA measurements, press RANGE Key.
The range to which the input value belongs is held and AUTO symbol turns off.
To cancel Range Hold, press RANGE Key for more than 1 second and AUTO
symbol turns on.
To cancel Range Hold, press RANGE Key for more than 1 second and AUTO
symbol turns on.
1.
2.
When measuring capacitance, press REL△ Key to make zero adjustment. In the
other functions, (〜V, V, Ω, mA, A) press this Key to make difference
measurements.
To cancel this Key, press it again and REL△ symbol disappears.
Select or , and DC or AC.
− ＋
Press HOLD Key while measuring, a measuring value is held on LCD with H
symbol shown.
To cancel this Key, press it again and H symbol disappears on LCD.
Press this Key to reset the operation of the function. This Key is used when
operation is mistaken in the measurment.
Press this Key to select Hz or Duty on 〜V, V, Hz, mA and A positions.
When making voltage, resistance or mA measurements, press RANGE Key to
select Range Hold. AUTO symbol turns off from LCD. There are two ways in
Range Hold.
Alligator
Clip
Alligator
Clip
Red
Test Prod
Test Prod
COM
mA
10A
FUSED
500mA MAX
FUSED
10A/15sec MAX
600V MAX
300V
MAX
Auto Power OFF
OFF
OFF
V
Hz
〜
V
m
A
A 〜
〜
〜
〜
KU-2600
CAT.
SELECT
RANGE
REL
HOLD
Hz/DUTY
RESET
Do not attempt to measure voltage that might exceed 600V AC or DC, the
specified maximum input of this instrument.
fig.3
fig.2
WARNING 5. Maximum Input Observance
WARNING 1. Checks of Body and Test Lead
WARNING 3. Warning for High Voltage Measurements
WARNING 4. Dangerous Voltage Measurement Procedure
WARNING 2. Warning for High Power Line Measurements
4-1. WARNINGS
Correct knowledge of electric measurements is essential to avoid unexpected
danger such as operator's injury or damage to the instrument. Read carefully and
observe the following precautions for safety measurements.
Before measurement, confirm the body of this instrument and handle insulators of
the Test Leads have no cracks or any other damages. Dust, grease and moisture
must be removed.
High Power Line (High Energy Circuits) such as Distribution Transformers, Bus
Bars and Large Motors are very dangerous. High Power Line sometimes includes
High Surge Voltage that could cause explosive short in the instrument and could
result in shock hazard. For voltage measurement of High Power Line, do not
touch Clamp Meter, its Test Leads, and any part of the circuit.
Even for Low Energy Circuits of electric/electronic appliances, such as heating
elements, small motors, line cords and plugs, High Voltage Measurements are
very dangerous. Do not touch Clamp Meter, Test Leads, and any part of the
circuit. Generally, shock hazard could occur when the current between the circuit,
that involves more than 33V rms or 46.7V DC or peak, and ground goes up to
0.5mA or more.
For dangerous voltage measurement, strictly observe the following procedure.
Before measurement, turn off the power of the circuit to be measured.
Plug Black Test Lead into COM terminal and Red Test Lead into VΩHz
terminal.
Attach Black and Red Alligator clips (optional) to Test Lead pins.
Set FUNCTION Switch to 〜V or V.
Confirm the power of the circuit to be measured is turned off. Connect Black
Alligator Clip to − (earth) side and Red Alligator Clip to + (positive) side.
(Refer to fig.2)
Place the Digital Multimeter away from your body not holding it in your hands.
Take safety distance from power source or circuit not to touch the dangerous
voltage.
Turn on the power of the circuit. Read the measurement value on LCD.
After measurement, turn off the power of the circuit and discharge the all
capacitors.
Disconnect Alligator Clips (with Test Leads) from the circuit.
1.
2.
3.
4.
5.
6.
7.
8.
9.
In case of live-line measurement, observe the following procedure.
Place the Digital Multimeter away from your body not holding it in your hands.
Set FUNCTION Switch to 〜V or V.
Attach Black Alligator Clip to Black Test Lead pin. Connect it to − (earth) side
of the circuit to be measured.
Take safety distance from power source or circuit not to touch the dangerous
voltage.
Hold Red Test Lead with one hand and connect it to ＋ (positive) side. (Refer
to fig. 3)
Read the measurement value on LCD.
After measurement, disconnect Red Test Lead and Black Alligator Clip from
the circuit.
1.
2.
3.
4.
5.
6.
7.
When taking measurement, always confirm that FUNCTION Switch is set to
correct position. Do not measure voltage on Ω, , , , mA and A positions.
WARNING 6. Correct Selection of FUNCTION Switch