Summary of KMLSP150W
Page 1
User manual kmlsp150w.
Page 2
I n d e x summarize ......................................................................... 3 product introduction .......................................................... 3 safety instruction ............................................................... 4 installation instruction ...............
Page 3
Summarize thank you for purchasing our led moving lighting. Please read these instructions carefully before begin and operate the fixtures according to these instructions to avoid any possible damages and accidents causes by misusage. Product introduction this light uses kandolite kmlsp150w led ligh...
Page 4
Safety instruction • please open the carton and check whether there is any damage at the arrival of the fixture. If there is any damage caused by transportation, please do not use the fixture and contact the distributor or manufacturer as soon as possible. • make sure the power supply voltages are c...
Page 5
If you have any questions or suggestions, please contact the distributor or manufacturer promptly. Installation instruction dimension diagram clamp release lock handle page 5 of 26.
Page 6
For safey wire instruction for changing interchangeable gobos fixed gobos wheels gobo wheels color wheel 1 color wheel 2 page 6 of 26.
Page 7
Main function 150w high brightness led 2 gobo wheels, 2 color wheels, iris, zoom, focus, prism and atomization accord with dmx512 protocol. Wireless dmx and dmx ethernet network is optional. The color wheel can reach any position 2 dmx channel modes multi strobe effect, 5 dimmer modes sound control,...
Page 8
Display operation menu : access the menu or return to a previous menu option enter : select the current menu option up : menu selection or parameter increments down : menu selection or parameters decrease page 8 of 26.
Page 9
Menu instruction menu dmx address 001-512 option pan inverte on/off tilt inverte on/off p/t swap on/off p/t feedback on/off dimmer mode off,dimmer1,dimmer2,dimmer3,dimmer4 channel mode 17ch/19ch display display intensity 01-32 display sleep permanently on/2 minutes/5 minutes/10 minutes manual contro...
Page 10
Note: 1. When entering menu *, the fixture is set automatically as a master to send data and the other fixtures will receive the data and work synchronously. When turn on the light again after power off, the fixture will jump to the same position. 2. The content with underline is factory default val...
Page 11
7 、 、 、 、3、 、 、 、1 pan inverte choose 【pan inverte】from menu, press【enter】to set pan inverte press 【up/down】to choose【on】or【off】 press 【enter】to exit and save the option 7 、 、 、 、3、 、 、 、2 tilt inverte choose 【tilt inverte】from menu, press【enter】to set tilt inverte press 【up/down】to choose【on】or【off...
Page 12
7 、 、 、 、3、 、 、 、6 dmx channel mode setting choose 【channel mode】from menu, press【enter】to set dmx channel press 【up/down】to choose【17ch】or【19ch】 press 【enter】to exit and save the option 7 、 、 、 、4 display setting menu display display intensity 01-32 display sleep permanently on/2 minutes/5 minutes/...
Page 13
Ch9:gobo1 rotate 0-255 ch10:gobo2 0-255 ch11:color1 0-255 ch12:color2 0-255 ch13:iris 0-255 ch14:zoom 0-255 ch15:focus 0-255 ch16:prism 0-255 ch17:atomization 0-255 ch18:moving blackout 0-255 ch19:control 0 choose 【manual control】from menu, press【enter】to set manual control of dmx value of 【ch1】~【ch...
Page 14
Note: 1 、 after pressing 【 enter 】 to confirm, gobo and color wheel will reset automatically once 2 、when the value is 128， the gobo and color wheel are in the middle; when the value is below 128, the gobo and color wheel are moving left by fine adjustment; when the value is above 128, the gobo and ...
Page 15
Note: 1 、、after pressing【enter】to confirm, gobo and color wheel will reset automatically once 2 、the factory default value is 128, i.E. The middle. 7 、 、 、 、8、 、 、 、2 recover factory default of setting parameter choose 【setting load】from menu, press【enter】to recover the factory default of setting pa...
Page 16
Note: 1 、 should disconnect with dmx controller before sending the parameters. 2 、 the setting of【dmx address】 and 【calibration】is invalid and won’t be sent. 3 、 the other fixtures will reset automatically once after receiving data correctly. Page 16 of 26.
Page 17
Dmx control function 17channels 19channels dmx value function ch1 ch1 0~255 dimming ， ， ， ，intensity zerofull ch2 ch2 0~10 11~20 21~60 61~100 101~140 141~180 181~220 221~255 shutter ， ， ， ，strobe shutter closed shutter open strobe ，slowfast electronic sine wave ，slowfast random strobe ，slowfast open...
Page 18
141~220 221~255 cwccw cycle ，slowfast reserved ch8 ch10 0~10 11~20 21~30 31~40 41~50 51~60 61~70 71~80 81~90 91~100 101~110 111~120 121~130 131~140 141~150 151~190 191~230 231~240 241~255 gobo 2 no gobo gobo1 gobo2 gobo3 gobo4 gobo5 gobo6 gobo7 shaking gobo1 shaking gobo2 shaking gobo3 shaking gobo4...
Page 19
91~100 101~110 111~120 121~130 131~140 141~150 151~180 181~190 191~220 221~230 231~255 color 1 （dark blue） color 2 （orange） color 3 （red） color 4 （purple） color 5 （green） color 6 （pink） color 7 （light yellow） cw flow effect ，slowfast color wheel stop ccw flow effect ，slowfast sound running reserved ...
Page 20
231~255 sound running reserved ch11 ch13 0~150 151~190 191~230 231~255 iris openclosed opening pulse ，slowfast closing pulse ，slowfast reserved ch12 ch14 0~255 zoom （zoom inzoom out） ch13 ch15 0~255 focus ch14 ch16 0~10 11~20 21~100 101~180 181~255 prism no prism prism active cw ，slowfast ccw slowfa...
Page 21
Xlr cable connecting xrl cable ： ： ： ： the stand connection way of the xrl is: one end connects to the male plug, and the other connects to the female. Noted ： in order to avoid failures and interference signal transmission ， we connect a resistance120Ω （ 1/4w ） at the end of the dmx connecting as b...
Page 22
The conversion between 3pin and 5 pin xlr if the output cable of dmx512 controller is the 5pin, please use 1pc 5pin to 3pin cable wiring diagram page 22 of 26.
Page 23
Problem analysis problem solution can not turn on the light check the power source plug is good or not check the switch of the lights is off or on check if the fuse is broken check if the switch power supply is good led not light (150w) check if the fan is broken the led can light up when the fan is...
Page 24
Maintenance lubrication: to achieve smooth zooming, we suggest lubricating 2 guide rails every 2 months. Should use good and heat resisting lubricating grease fixture cleaning: to use the fixture reliably, it is very important to keep it clean. Too much dust will cause malfunction of control ic boar...
Page 25
Technical specification input voltage ：ac100v-240v 50-60hz rated power: 300w （pf>90%） lamp specs: led-150w （6500k） life span: above 50000-100000 hours output luminous flux: 6200lm color: 2 color wheels with 7 colors & white gobo ：2 gobo wheels, 1 fixed gobo wheel，7 fixed gobos + white； 1 rotating go...
Page 26
Copyright 2012 kandolite. All rights reserved. Due to continuous improvements and innovations, specifications may change without notice..