DL manuals
Kanguru
TV
Databank
User Manual

Kanguru Databank User Manual

Manual is about: Kanguru Databank Network Attached Storage: User Guide

Page of 13

Download

Print this page

Bookmark us

FCC COMPLIANCE STATEMENTS

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to

equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the Distance between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

TRADEMARKS

MS-DOS, Windows, Windows 98/NT/2000/ME/XP are trademarks of Microsoft Corporation.

Macintosh and Mac are trademarks of Apple Computer

*All of the third-party brands and names are the property of their respective owners.

1 2 3 4 5 6 7 Next › »

Summary of Databank

Page 1
Fcc compliance statements this equipment has been tested and found to comply with the limits for a class b digital device, pursuant to part 15 of the fcc rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment gener...
Page 2: Table Of Contents
Table of contents 1. Introduction ............................................................................................................................................................................................ 2 2. System requirements .......................................................
Page 3: 2. System Requirements
You use your databank if you want to reach maximum transfer speeds. Note2: kanguru databanks can be custom built to include cdrw, dvdrw, and card reader drives. If your databank has one of these custom drives, then follow the instructions for operating that particular drive. If not, then disregard t...
Page 4
• the “windows has finished installing the software that your new hardware device requires” dialog appears. Click “finish.” • repeat the above process for the second nec usb open host controller. Figure 2 • after you have installed the two nec usb open host controllers, windows will find a “pci univ...
Page 5
Finalizing usb 2.0 hi-speed hardware settings usb 2.0 hi-speed products that use an nec chipset have 3 usb host controller engines on board. Two of the host controller engines handle usb 1.1 transactions. One of the host controllers engines handle, usb 2.0 transactions. Usb data traffic is automatic...
Page 6: 4. Driver Installation
Connecting the kanguru databank 1.) boot-up your computer and make sure the usb / usb2.0 port device driver has been installed and is available in operating system. 2.) plug the usb2.0 cable into the usb2.0 port of computer. 3.) plug the ac power cord to the inlet of your kanguru databank and power ...
Page 7
5. Then open the “usb winme-98-2000-xp” folder 6. Run the “tppinst.Exe” to install drivers for the kanguru databank. 7. Choose the language that you use and click “ok”. A dialog box appears as shown, click “next 8. Choose “typical” and click “next”. 6. After the needed files are copied onto your har...
Page 8
This kanguru databank is supported by the mass storage device drivers in win me/2000/xp systems directly .You don’t need to install any drivers. If the kanguru databank has been repartitioned by the user, please refer to the partition the kanguru databank chapter to prepare your unit. 4.3 mac os ste...
Page 9
5. Operating the kanguru databank once the databank has been installed you can connect or disconnect individual kanguru disks at anytime without powering down the databank or your system. Please follow the steps below when you want to remove a drive while the databank is still running: 5.1 connectin...
Page 10
5.2.3 mac os when disconnecting your kanguru databank usb 2.0 external drive from computer, close all windows and quit all running applications that are stored on the kanguru databank usb 2.0 external drive. Drag the kanguru databank usb 2.0 external drive’s icon into “trash” to dismount it from the...
Page 11: Your Kanguru Databank.
6. Partitioning an individual kanguru disk from your kanguru databank. 6.1 partition under windows 98/me boot-up the computer into windows 98/me system. Plug the kanguru databank into a computer. There are two methods to partition and format individual kangurudisk in the databank: method 1. Step1 cl...
Page 12
To step 1 to proceed. Step4 in the first screen of fdisk, answer the questions as follows: do you want to enable large disk support ? [y] if you want to build a partition larger than 2gb. [n] if you want to build a partition small than 2gb. Step5 the next screen is [fdisk options], and type “5” to s...
Page 13: Tech Support
You can create a new or delete an existing partition by right-clicking in this area. Step3. Right-click on the right area of the kangurudisk. Click on [create partition....] and ”create partition wizard” will appear. Step4. Follow the instructions of the wizard to partition and format your kangurudi...