- DL manuals
- Kantech
- Controller
- Door Controller Innovative and Powerful KT-300
- Installation Manual
Kantech Door Controller Innovative and Powerful KT-300 Installation Manual
Summary of Door Controller Innovative and Powerful KT-300
Page 1
Dn1315-1007 v01.02 kt-300 door controller installation manual.
Page 3
Kt-300 door controller installation manual dn1315-1006 v01.02 i table of contents pre-installation information ....................................................................................................................... 1 copyright information ................................................
Page 4
Ii dn1315-1006 v01.02 installation and wiring ............................................................................................................... 14 applying power .................................................................................................................15 assignin...
Page 5: III
Iii kantech warranty terms for kantech products provided with or without components or software kantech products purchased with or without components and software is copyrighted and is purchased under the following limited warranty terms: sensomatic electronics, llc (“kantech”) warrants the original...
Page 6
Iv but are not limited to, loss of profits, loss of the product or any associated equipment, cost of capital, cost of substitute or replacement equipment, facilities or services, down time, purchaser’s time, the claims of third parties, including customers, and injury to property. The laws of some j...
Page 7
V and installed correctly. If a device operates only by ac power, any interruption, however brief, will render that device inoperative while it does not have power. Power interruptions of any length are often accompanied by voltage fluctuations which may damage electronic equipment such as an access...
Page 8
Dn1315-1007 1 kt-300 door controller installation manual pre-installation information to the installer: if you are familiar with the installation, you can use the checklist with the symbol. Copyright information copyright © 2010 tyco international ltd. And its respective companies. All rights reserv...
Page 9
Dn1315-1007 2 kt-300 door controller installation manual kt-300 compliance specifications fcc & ic compliance this device complies with fcc part 15, subpart b:2009. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must acce...
Page 10
Dn1315-1007 3 kt-300 door controller installation manual overview the kt-300 will operate with the entrapass software innovative and powerful the kantech kt-300 door controller is designed to meet the highest standards of access control and point monitoring applications. Downloadable firmware the fi...
Page 11
Dn1315-1007 4 kt-300 door controller installation manual technical specifications specification description ac power imput 120/16vac, 40va, class 2 transformer (north america) 230/16vac, 100va, fused transformer (europe) battery back-up 1battery 12vdc, 7ah, supervised, provides up to 12 hours of ope...
Page 12
Dn1315-1007 5 kt-300 door controller installation manual electrical specifications kt-300 controller and accessories voltage outputs maximum current (n.A.) maximum current (eu) absolute combined maximum (n.A.) absolute combined maximum (eu) lock outputs (12 vdc) 500 ma (250 ma each) 1.0 a (500 ma ea...
Page 13
Dn1315-1007 6 kt-300 door controller installation manual vc-485 or usb-485 multi-function communication interface kantech model description.
Page 14
Dn1315-1007 7 kt-300 door controller installation manual installing the kt-300 physical installation check for ideal indoor location. Stay away from electrical or communication devices. The kt-300 controller cabinet has been designed to be mounted on a wall without any additional enclosures. The cab...
Page 15
Dn1315-1007 8 kt-300 door controller installation manual hooking up inputs connect devices to inputs 1 to 8. Resistors (included with kt-300) for all inputs 5.6k ohm (if selected). The kt-300 has an on-board capability of monitoring 8 input points (expandable to 16 if kt-pc4108 module is used). Each...
Page 16
Dn1315-1007 9 kt-300 door controller installation manual auxiliary outputs connect auxiliary outputs to readers and local warning devices. Auxiliary outputs are used for visual and audible signals. They can be activated according to schedules, input conditions or events and local alarms. Auxiliary o...
Page 17
Dn1315-1007 10 kt-300 door controller installation manual connecting the master controller to the host pc connect flat cable from kt-300 to the pc. From 0 to 30m (0 to 100 feet): if the local master controller is located less than 30m (100 feet) from the host computer, use the on-board rs- 232 rj12 ...
Page 18
Dn1315-1007 11 kt-300 door controller installation manual powering the kt-300 install 120 v / 16vac, 40 va, class 2 transformer (north am.). Connect 230 v / 16vac, 100 va, fused transformer (eur.) place battery in cabinet. Power the kt-300 controller. The kt-300 controller must be powered by a 16vac...
Page 19
Dn1315-1007 12 kt-300 door controller installation manual combus repower (if required) depending on how many modules are connected to the combus and how far they are from the kt-300 controller, you may need to “repower” the controller’s combus. The combus needs to be “repowered” if the voltage drops...
Page 20
Dn1315-1007 13 kt-300 door controller installation manual kt-pc4108 input module kt-pc4108 introduction the kt-pc4108 module is a zone input module that adds up to 8 fully programmable zones to the kt-300 controller. Kt-pc4108 specifications • connects to the controller via 4-wire combus • current d...
Page 21
Dn1315-1007 14 kt-300 door controller installation manual kt-pc4204 - 4-relay and additional power supply module kt-pc4204 introduction the kt-pc4204 module is an output module with four programmable relays. This module can be used to “repower” the combus. The kt-pc4204 can also be used for elevator...
Page 22
Dn1315-1007 15 kt-300 door controller installation manual once wiring is completed, the module must be assigned to the system. To assign the module, perform the following: 1. Establish communication between the pc and the controller. 2. Remove the tamper switch wire (or only the wire if tamper switc...
Page 23
Dn1315-1007 16 kt-300 door controller installation manual applying power 1. After all wiring is completed, apply power to the kt-300. 2. Connect the battery leads to the battery. 3. Then, connect the ac transformer. Note: do not connect the power until all wiring is completed. Assigning the kt-pc421...
Page 24
Dn1315-1007 17 kt-300 door controller installation manual wiring the kt3-lcd before beginning to wire the unit, ensure that all power (ac transformer and battery) is disconnected from the control panel. To complete keypad wiring, connect the four combus wires (red, black, yellow and green) to keypad...
Page 25
Dn1315-1007 18 kt-300 door controller installation manual visual status indicators (leds) the kt-300 controller has multiple status indicators such as for troubleshooting, network activity, power status and outputs activity. Please refer to the graphic below for a detailed view of their location. • ...
Page 26
Dn1315-1007 19 kt-300 door controller installation manual kt-300 controller maintenance recommendations the kt-300 circuit board includes a lithium battery (see the kt-300 controller wiring diagram on page 20). This battery must be replaced by a kantech technician to avoid any risk of explosion. If ...
Page 27
Dn1315-1007 20 kt-300 door controller installation manual kt-300 wiring diagram (north american version).
Page 28
Dn1315-1007 21 kt-300 door controller installation manual kt-300 wiring diagram (eu version).