1. DL manuals
  2. Kantech
  3. Gateway
  4. Ethernet Four-Door Controller KT-400
  5. Installation Manual

Kantech Ethernet Four-Door Controller KT-400 Installation Manual

Manual is about: Ethernet Four-Door Controller

Summary of Ethernet Four-Door Controller KT-400

  • Page 1

    Dn1726-0811 kt-400 ethernet four-door controller installation manual.

  • Page 3

    Dn1726-0811 iii kt-400 ethernet four-door controller installation manual table of contents pre-installation information ......................................................................................................................... 1 copyright information .....................................

  • Page 4

    Dn1726-0811 iv configuring the kt-400 ethernet four-door controller with the kt-finder .............................................. 33 installation checklist ................................................................................................................................. 37 inputs ...

  • Page 5

    Dn1726-0811 1 kt-400 ethernet four-door controller installation manual pre-installation information to the installer: if you are familiar with the installation, you can use the installation checklist on page 37 with the symbol . Copyright information copyright © 2008 tyco international ltd. And its ...

  • Page 6

    Dn1726-0811 2 technical support for technical assistance with the kt-400 ethernet four-door controller and other kantech products, contact technical support, monday to friday. See the following table for the technical support phone numbers. Country/region phone numbers support hours email north amer...

  • Page 7

    Dn1726-0811 3 kt-400 ethernet four-door controller installation manual compliance specifications fcc & ic compliance this device complies with part 15 of the fcc rules class a. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this devi...

  • Page 8

    Dn1726-0811 4 • 1 gb ram • minimum free hard disk space: 20 gb • color depth: 24-bit (16 million colors), required for video integration only • screen resolution: 1024 x 768 • graphic adapter card: 32 mb • 48x cd-rom drive • network interface card: 10/100 base-t network adaptor note: actual requirem...

  • Page 9

    Dn1726-0811 5 kt-400 ethernet four-door controller installation manual overview the kt-400 ethernet four-door controller is designed to meet the highest standards of access control and point monitoring applications. Here are the features of the kt-400 ethernet four-door controller. Compatible with a...

  • Page 10

    Dn1726-0811 6 inputs there are 16 onboard inputs on the kt-400 ethernet four-door controller. Up to 240 more can be added through the addition of expansion modules, such as the kt-mod-inp16, for a total of 256 inputs. Each input can be individually configured for one of the following application: • ...

  • Page 11

    Dn1726-0811 7 kt-400 ethernet four-door controller installation manual downloadable firmware the firmware program can be downloaded from any entrapass workstation to the kt-400 ethernet four-door controller. The firmware program, stored in the controller’s flash memory, is upgraded without having to...

  • Page 12

    Dn1726-0811 8 figure 1: kt-400 ethernet four-door controller pcb view.

  • Page 13

    Dn1726-0811 9 kt-400 ethernet four-door controller installation manual figure 2: kt-400 ethernet four-door controller inputs and outputs view 10/100 base-t ethernet por t computer network kt -300 kt -100 rs485 bus (com1) tamper nc c nc z3 nc dr y cont act input defined option with double eol resist ...

  • Page 14

    Dn1726-0811 10 figure 3: kt-400 cabinet model for north america.

  • Page 15

    Dn1726-0811 11 kt-400 ethernet four-door controller installation manual system architecture the kt-400 ethernet four-door controller can be used through various site applications with entrapass special edition, entrapass corporate edition and entrapass global edition. Applications with entrapass spe...

  • Page 16

    Dn1726-0811 12 figure 5: usb-485 with entrapass special edition and corporate edition with corporate gateway figure 6: vc-485 with entrapass global edition and global or corporate gateway.

  • Page 17

    Dn1726-0811 13 kt-400 ethernet four-door controller installation manual figure 7: over the internet with a kt-ncc and entrapass global edition figure 8: over rs-232 straight from the entrapass rs-232 com port.

  • Page 18

    Dn1726-0811 14 vital led heartbeat patterns communication status and other vital controller parameters can be obtained from vital led heartbeat patterns. It is located near the rs-232 port (com3), see figure 1 . This information is particularly useful when connecting the controller to the rest of th...

  • Page 19

    Dn1726-0811 15 kt-400 ethernet four-door controller installation manual technical specifications type description power input ( kt-400 ) transformer class 2, in 120 vac; out 16 vac, 75 va battery back-up ( kt-batt-12 ) 12 vdc, 7 ah battery supervised, provides up to 12 hours of operation operating t...

  • Page 20

    Dn1726-0811 16 electrical specifications kt-400 ethernet four-door controller models, expansion modules models, related documentation and miscellaneous items open collector outputs maximum current (typical) combined maximum current leds (led, out1 and out2) for each door reader 25 ma (each) 2 amps f...

  • Page 21

    Dn1726-0811 17 kt-400 ethernet four-door controller installation manual dn1475 entrapass special edition, reference manual - spanish version dn1436 entrapass corporate edition, reference manual - spanish version dn1599 entrapass global edition, reference manual - spanish version dn1514 entrapass spe...

  • Page 22

    Dn1726-0811 18 models information • kt-400 : cabinet with one kt-400 for north america, up to three expansion modules can be installed in the cabinet, • kt-400-pcb : kt-400 with parts, • kt-400-acc : accessory kit, • kt-400-cab : cabinet only for north america, table 2: models bills of material note...

  • Page 23

    Dn1726-0811 19 kt-400 ethernet four-door controller installation manual installing the kt-400 ethernet four-door controller preparing to install the kt-400 ethernet four-door controller required to install kt-400 ethernet four-door controller • for north america: ac transformer 120 vac 60 hz in; 16 ...

  • Page 24

    Dn1726-0811 20 warning: controlled door locks may be governed by regulatory bodies and should always be installed according to local regulations. In most instances, there are strict limitations to installing fail-secure devices and fail-safe locking devices such as magnetic locks or other similar lo...

  • Page 25

    Dn1726-0811 21 kt-400 ethernet four-door controller installation manual relay controlled outputs the kt-400 provides four relay outputs relay1 to relay4 (3 amps, 30 vac/vdc). The kt-400 can be expanded up to 256 controlled outputs when using expansion modules. • the kt-mod-out16 module provides 16 o...

  • Page 26

    Dn1726-0811 22 connecting the kt-400 ethernet four-door controller connecting the vc-485 or the usb-485 to the rs-485 bus connect the rs-485 cable to (com1) + 485 - and the rs-485 signal ground to the 12 vdc aux - (negative) controllers are linked together through their rs-485 terminals. The maximum...

  • Page 27

    Dn1726-0811 23 kt-400 ethernet four-door controller installation manual connecting the master controller to the host pc via rs-232 connect rs-232 cable from kt-400 to the pc (maximum length 30 m (100 ft)) if the local master controller is located more than 30 m (100 ft) from the host computer, you m...

  • Page 28

    Dn1726-0811 24 spi expansion port the spi (serial peripheral interface) expansion port on the kt-400 is used to connect expansion modules, in order to add more inputs and outputs such as relays. The maximum current draw for the spi expansion port is 500 ma when the 12v aux terminals are not used. Th...

  • Page 29

    Dn1726-0811 25 kt-400 ethernet four-door controller installation manual important installation rules about expansion modules note 1: the maximum current draw must be calculate each time there is a new module added to the spi chain. Rule 2: the spi cable, between the kt-400 and the 1st module or betw...

  • Page 30

    Dn1726-0811 26 figure 10: pcb view of expansion modules.

  • Page 31

    Dn1726-0811 27 kt-400 ethernet four-door controller installation manual figure 11: example of kt-400 ethernet four-door controller interconnection with expansion modules motion detect or buzzer power tamper - ++ - no1 nc1 c1 12 vdc cont act door locking device buzzer regula ted power suppl y 12 vdc,...

  • Page 32

    Dn1726-0811 28 figure 12: expansion modules cabinet for north america.

  • Page 33

    Dn1726-0811 29 kt-400 ethernet four-door controller installation manual troubleshooting table 3: reset types and descriptions jumpers heartbeats patterns resets continuous quick flashing soft reset: when jp2 and jp3 are on, the controller will reset on a) power up, b) pushbutton, or c) entrapass sof...

  • Page 34

    Dn1726-0811 30 default initialization the kt-400 default initialization or factory default dhcp is done at kantech. The following steps should only be followed if: a) you want to configure the kt-400 with the kt-finder, see page 33. B) the kt-400 was communicating via the rs-232 port and you have in...

  • Page 35

    Dn1726-0811 31 kt-400 ethernet four-door controller installation manual kt-400 ethernet four-door controller maintenance recommendations the kt-400 includes a lithium ion rechargable battery (see the kt-400 ethernet four-door controller pcb view on page 8). This battery must be replaced by a kantech...

  • Page 36

    Dn1726-0811 32 configuring the kt-400 ethernet four-door controller with the web configuration page this procedure is practical if you want to configure the kt-400 in advance before going on site. Optional documentation application note, networking basics , dn1796. Before you start • the detachable ...

  • Page 37

    Dn1726-0811 33 kt-400 ethernet four-door controller installation manual configuring the kt-400 ethernet four-door controller with the kt-finder the kt-finder is an application used to configure the kt-400 over the local area network (lan) or the wide area network (wan). It doesn’t require any instal...

  • Page 38

    Dn1726-0811 34 configuring the kt-400 ethernet four-door controller with the kt-finder (continued) 7. Put jumpers on jp2 and jp3 . 8. Verify your network configuration information sheet : • enter the entrapass ip address or the domain name of the entrapass gateway . This information must be the same...

  • Page 39

    Dn1726-0811 35 kt-400 ethernet four-door controller installation manual kt-400 ethernet four-door controller network configuration information sheet please complete one sheet per kt-400 ethernet four-door controller company name: site name: lan or wan (see other side) configuration in a local area n...

  • Page 40

    Dn1726-0811 36 configuration in a wide area network (wan) entrapass site for more details, refer to the entrapass reference manual. Entrapass special edition / corporate gateway ip address: ______.______.______.______ router public ip address:______.______.______.______ or domain name: _____________...

  • Page 41

    Dn1726-0811 37 kt-400 ethernet four-door controller installation manual installation checklist to the installer: if you are familiar with the installation, you can use the checklist with the symbol. Installing the kt-400 ethernet four-door controller preparing to install the kt-400 ethernet four-doo...

  • Page 42

    Dn1726-0811 38 inputs and outputs assignments sheet doors door 1 contact rex door 2 contact rex door 3 contact rex door 4 contact rex inputs door z1 no or nc eol, dry or deol rex z2 no or nc eol, dry or deol input z3 no or nc eol, dry or deol input z4 no or nc eol, dry or deol door z5 no or nc eol, ...

  • Page 43

    Dn1726-0811 39 kt-400 ethernet four-door controller installation manual figure 14: kt-400 cabinet inner door sticker diagram (north america) figure 15.

  • Page 44

    Dn1726-0811 40