Warning: this manual contains information on limitations regarding product use and function and information on the limitations as to liability of the manufacturer. The entire manual should be carefully read. K t - 1 0 0 ™ d o o r c o n t r o l l e r i n s t a l l a t i o n m a n u a l kantech system...
Products names are trademarks or registered trademarks of their owners. No part of this publication may be reproduced in any form without permission from kantech systems, inc. Kantech systems web site: www.Kantech.Com © 2002, kantech systems all rights reserved. Specifications may be modified withou...
Ta b l e o f c o n t e n t s section 1: kt-100 features 3 section 2: m ounting and w iring the kt-100 door controller 5 step 1•unpacking the kt-100 ..............................................5 step 2•selecting a mounting location .................................5 step 3•installing the power supp...
6.
K t - 1 0 0 i n s t a l l a t i o n m a n u a l 3 s e c t i o n 1 : k t - 1 0 0 f e a t u r e s the kt-100 door controller contains all the intelligence and necessary inputs/outputs to manage one door; it is also easily linked to a network controlling up to 32 doors. The kt-100 door controller featu...
4 k t - 1 0 0 i n s t a l l a t i o n m a n u a l.
K t - 1 0 0 i n s t a l l a t i o n m a n u a l 5 s e c t i o n 2 : m o u n t i n g a n d wi r i n g t h e k t - 1 0 0 d o o r c o n t r o l l e r step 1•unpacking the kt-100 the kt-100 controller has been designed to be mounted on a wall in a single gang electrical box without any additional enclos...
6 k t - 1 0 0 i n s t a l l a t i o n m a n u a l door closer. A standard hydraulic door closer is almost mandatory to insure that the door closes automatically after an entry and to prevent “door open too long” or “door left open” alarms. Door contact. When the door is locked, the access controller...
K t - 1 0 0 i n s t a l l a t i o n m a n u a l 7 to connect inputs: 1. Connect devices between inputs z1 to z4 and com. 2. Connect resistors (included with kt-100) for all inputs 5.6k ohm (if selected). Note: inputs can be defined with none or one end-of-line resis- tor according to parameters defi...
8 k t - 1 0 0 i n s t a l l a t i o n m a n u a l the normally closed tamper switch is connected to an input. It is recommended to choose an unused input (3 or 4) as tamper input. 1. Install the kt-100tamp tamper switch in the musb box as illustrated below. Step 10• connecting the kt-100 to the rs-4...
K t - 1 0 0 i n s t a l l a t i o n m a n u a l 9 s e c t i o n 3 : a p p e n d i x typical kt-100 wiring diagram pw r i n 12 v d c pw r o u t 12 v d c loc k pw r en t r y e xi t le d b u z +- + 5 v w ht gr n w ht gr n ou t p u t s kt -1 0 0 ca rd re a d e r s 75 0m a m a x +- 50 0m a m a x -- m a d...
10 k t - 1 0 0 i n s t a l l a t i o n m a n u a l kt-100 compliance notices this device complies with part 15 of the fcc rules. Operation is subject to the following two conditions: ◗ (1) this device may not cause harmful interference, and ◗ (2) this device must accept any interference received inc...
K t - 1 0 0 i n s t a l l a t i o n m a n u a l 11 kt-100 controller maintenance to ensure the best operating conditions, it is highly recommended to test the kt-100 controller by performing the following tests. Bi-annual test for battery this test will ensure that if a power failure occurs, the bat...
K t - 1 0 0 i n s t a l l a t i o n m a n u a l 12 using the kt-100 with an external alarm panel to interface the kt-100 to an external alarm panel: 1. Connect the kt-100 two inputs (zone 3 and 4) to the external alarm status relay (pgm1 and pgm2) 2. Connect the kt-100 two outputs (relay 3 and 4) to...
Kantech systems web site: www.Kantech.Com © 2002, kantech systems. All rights reserved. Specifications may be modified without notice. ™ trademarks of kantech systems. Printed in canada • dn5073-0205-0207.
