- DL manuals
- Karcher
- Vacuum Cleaner
- NT 27/1 Advanced
- Service Manual
Karcher NT 27/1 Advanced Service Manual
Summary of NT 27/1 Advanced
Page 1
English 5.906-472.0 rev. 00 (08/08) 1 nt 27/1, -advanced, nt 27/1 me, -me advanced nt 48/1 service manual.
Page 2
2 english 5.906-472.0 rev. 00 (08/08) contents 1 preface 3 2 safety instructions 3 2.1 hazard levels 3 3 technical features 3 3.1 proper use 3 3.2 general 3 3.3 filter and vacuum system 3 3.4 electrical system 3 4 parts of the system 4 4.1 view of nt 27/1 4 4.2 view of nt 48/1 5 4.3 suction head rem...
Page 3
English 5.906-472.0 rev. 00 (08/08) 3 good service work requires extensive and practice-oriented train- ing as well as well-structured training materials. Hence we offer regular basic and advanced training programmes covering the entire product range for all service engineers. In addition to this, w...
Page 4
4 english 5.906-472.0 rev. 00 (08/08) 1 clip system 2 handle 3 suction hose 4 carrying handle 5 cable hook 6 storage compartment for tools 7 lock for suction head (2x), (as of july 2008) 8 lock for suction head (2x) 9 accessory mount 10 dirt receptacle 11 swivel casters (5x) 12 floor nozzle 13 sucti...
Page 5
English 5.906-472.0 rev. 00 (08/08) 5 1 carrying handle 2 cable hook 3 storage compartment for tools 4 lock for suction head (2x), (as of july 2008) 5 intake for dirt water drain hose 6 lock for suction head (2x) 7 dirt water drain hose 8 dirt receptacle 9 accessory mount 10 impeller (2x) 11 guiding...
Page 6
6 english 5.906-472.0 rev. 00 (08/08) Î open the locks on the suction head and remove the suction head (3) from the dirt container (6). 1 fastening nut, cartridge filter 2 cartridge filter 3 suction head 4 seal 5 suction air guide 6 dirt receptacle 7 suction hose connection the nt 48/1 is equipped w...
Page 7
English 5.906-472.0 rev. 00 (08/08) 7 after a certain amount of use, the cartridge filter is dirty and must be cleaned or replaced as needed. Î remove the suction head (see chapter 4.2). Î unscrew the fastening nut (1). Î remove the cartridge filter (2) toward the top. Î install the cleaned or new c...
Page 8
8 english 5.906-472.0 rev. 00 (08/08) Î remove the suction head (see chapter 4.2). Î remove the fastening screws (1). Î remove the suction turbine casing (2) from the suction head casing (6). 1 fastening screws (4x), suction turbine casing 2 suction turbine housing 3 insulation 4 suction turbine (m1...
Page 9
English 5.906-472.0 rev. 00 (08/08) 9 1 connecting cable, suction turbine (m1) 2 de-interference capacitor (c1) 3 appliance switch (s1) 4 mains cable 5 connector plug (2x), suction turbine and de-interference ca- pacitor 6 connector plug (2x), mains cable 7 bracket Î separate the suction turbine cas...
Page 10
10 english 5.906-472.0 rev. 00 (08/08) Î the suction turbine (6) can be removed for cleaning or replace- ment. Note when installing the suction turbine, watch for correct placement. The protrusions on the suction turbine must be aligned with the screw heads (see arrows). Observe the following when i...
Page 11
English 5.906-472.0 rev. 00 (08/08) 11 if the abrasive coals on the suction turbine (m1) are worn, they can be replaced as follows. Î press the locking noses (2) on both sides of the cover (1) slight- ly toward the outside and remove the cover (1) toward the top. Î pull off the connector plug (6). Î...
Page 12
12 english 5.906-472.0 rev. 00 (08/08) 6 circuit diagram 6.1 circuit diagram 0.088-563.0 c1 de-interference capacitor m1 suction turbine s1 power switch x1 mains plug x2 socket (te version only).
Page 13
English 5.906-472.0 rev. 00 (08/08) 13 the technical specification sheet and the circuit diagram will be in- cluded in the next version of the spare parts cd (disis) and in the intranet. The operating instructions and the spare parts list can be request- ed in paper form with the respective part num...