Owners manual j series decorative aerators contents important safety instructions. . . . Pg2 general owner’s instructions. . . . Pg2 unit specs. . . . Pg3 parts included. . . . Pg3 assembly instructions. . . . Pg4 nozzle options & pattern sizes. . . . Pg7 optional premium nozzles. . . . Pg8 installa...
2 thanks we at kasco marine, inc. Would like to both thank and congratulate you on your purchase of the jf model decorative aerator. We appreciate you choosing kasco and for your purchase. Your decision to purchase kas- co’s decorative aerator will not disappoint you. The jf series decorative aerato...
3 parts included 8400jf, 3.1jf, or 5.1jf aerator 2.3jf, 3.3jf, or 5.3jf aerator (unit with cord or unit with disconnect) (1) a1. Cord in separate box (1) (depending on size of cord) b. Float in separate box (1) (diagram) # item part # qty 1a float sections (2, 3 hp only) 284001 3 1b float sections (...
4 • #10 x 1” long or longer screw(s) for mounting the control panel (4) • 7/16” socket & wrench (1) • 7/16” wrench (1) • 9/16” socket & wrench (1) • 9/16” wrench or adjustable crescent wrench (1) • flat head screw driver (1) assembly instructions 1. Remove all contents from package and place on a cl...
5 7. Take flat mesh pattern and wrap into cone shape by overlapping both vertical edges by approximately 1 inch and aligning top and bottom edges of mesh. Se- cure mesh vertical seam at the top, bottom and middle using (3) cable ties. Overlap vertical edges 1 inch overlap attach 3 cable ties place m...
6 bottom screen clips (part #b12) over the bolts as shown. The power cord can be slid under the bottom screen between the float and screen where two float sections come together before the 3/8” lock nuts are replaced. Replace the three inside lock nuts and tighten all 3/8” lock nuts using the 9/16” ...
7 • the spruce nozzle must have the insert removed prior to nozzle placement. • the birch display does not require a nozzle. The redwood nozzle uses the 3 self tapping screws to attach over the pump housing and the y insert must be installed. Model hp height width 8400, 2.3 2 22’ 7’ 3.1, 3.3 3 24’ 8...
8 the birch display does not use a nozzle or bolt. It is the aerator unit running without any nozzle and allows for the best flow rate and oxygen transfer! Model hp height width 8400, 2.3 2 12’ 11’ 3.1, 3.3 3 14.5’ 10’ 5.1, 5.3 5 14’ 12’ 7.3 7.5 14.5’ 13’ the sequoia nozzle (marked s on the inside o...
9 installation instructions before installing 3 phase units (2.3, 3.3, 5.3, 7.3) into the pond, please refer to 3 phase startup procedure. Use the ropes to position the aerator in the desired location in the pond/lake. Anchor the ropes or secure them to the shoreline so the ropes are free of slack, ...
10 disconnection means. C-85 panel requires at least a 30amp protected circuit feeding the panel. C-95 panel requires at least a 40amp protected circuit feeding the panel. Connect your power feed as detailed in the wiring diagram provided with this panel. L1 connects to terminal #1 l2 connects to te...
11 light kit connections: black connects to terminal #6 white connects to terminal #7 green connects to terminal g step four: test the gfcb with the test button now and every 30 days. If lights are installed, they can now be installed per instructions included with the lights. Once completed, power ...
12 c85 / c95 non-metallic wiring diagram *c95 uses 30 amp breaker.
13 3 phase startup procedure if a kasco control panel is not provided, please refer to the following warnings: when inherent overheating protection is not provided: use with approved motor control that matches motor input in full load amperes with overload element(s) selected or adjusted in accordan...
14 programming with manual override switch your timer may have a 3-way manual switch or a 2-way manual switch. Automatic mode in order to operate the time clock in the automatic mode, the manual switch must be in the automatic postion- see diagram. Manual mode for the 3-way switch, with the manual o...
15 1 2 3 4 5 6 7 8 11 12 14 15 18 16 17 9 13 8400j replacement parts 10 item no. Part no. Description qty. 1 475628 screw, fillister head 3 2 840250 jet pump housing 1 3 840240 2 hp housing cone 1 4 475626 flat washer, #10 3 5 475625 screw, 10-24 x 2.5" long 3 6 840260 impeller, 8400 1 7 475642 wash...
16 1 2 3 4 5 7 8 9 12 13 14 16 15 10 11 2.3j replacement parts 6 17 item no. Part no. Description qty. 1 475628 screw, fillister head 3 2 840250 jet pump housing 1 3 840240 2 hp housing cone 1 4 475626 flat washer, #10 3 5 475625 screw, 10-24 x 2.5" long 3 6 360100 impeller lock nut 1 7 840261 2 hp ...
17 1 2 3 4 5 6 7 8 10 12 14 13 15 9 11 3.1j replacement parts 16 item no. Part no. Description 3 hp/qty. 1 475628 screw, fillister head 3 2 840250 jet pump housing 1 3 840240 2 hp housing cone 1 4 475626 flat washer, #10 3 5 475625 screw, 10-24 x 2.5" long 3 6 840360 impeller, 3 hp 1 7 475642 washer...
18 1 2 3 4 5 6 7 8 10 11 14 13 15 9 12 3.3j replacement parts 17 item no. Part no. Description 3 hp/qty. 1 475628 screw, fillister head 3 2 840250 jet pump housing 1 3 840240 2 hp housing cone 1 4 475626 flat washer, #10 3 5 475625 screw, 10-24 x 2.5" long 3 6 840360 impeller, 3 hp 1 7 475642 washer...
19 2 1 3 4 5 6 7 8 10 11 14 13 15 9 12 5.1j replacement parts 16 item no. Part no. Description qty. 1 840550 5.1 j housing 1 2 475628 screw, fillister head 3 3 840558 cone, 5.1j 1 4 475626 flat washer, #10 3 5 475625 screw, 10-24 x 2.5" long 3 6 840560 impeller, 5 hp 1 7 475642 washer, 1/2" 1 8 8402...
20 1 2 3 4 5 7 8 9 11 12 15 14 16 10 13 5.3j replacement parts 6 17 item no. Part no. Description qty. 1 475628 screw, fillister head 3 2 840550 5.1 j housing 1 3 840558 cone, 5.1j 1 4 475626 flat washer, #10 3 5 475625 screw, 10-24 x 2.5" long 3 6 360100 impeller lock nut 1 7 840561 5 hp impeller 1...
21 1 2 3 4 5 18 8 10 11 13 15 14 16 9 12 7.3j replacement parts 6 19 item no. Part no. Description qty. 1 475628 screw, fillister head 3 2 702200 upper housing, 7 hp 1 3 840240 2 hp housing cone 1 4 475626 flat washer, #10 3 5 475625 screw, 10-24 x 2.5" long 3 6 360100 impeller lock nut 1 8 475642 w...
22 maintenance recommendations ** under no circumstances should anyone enter the water while a aerator is operating. ** ** please keep the original box for maintenance ship- ping. ** the following maintenance procedures can be uti- lized to ensure many years of quality performance from your kasco ae...
23 warranty policy 3 year limited warranty: kasco® marine, inc. War- rants this aerator to be free from defects in material or workmanship (except for the ropes, power cord, and propeller) under normal use and service. The kasco marine, inc. Obligation under this warranty is limited to replacing or ...
24 expense for shipping and handling charges. Billing: all non-warranty repairs will be returned to the customer and billed c.O.D. Unless otherwise directed. Kasco marine also accepts visa and mastercard credit card payments. Kasco marine will call for credit card information upon completion of the ...
25 be started by spinning the prop with a stick, the starting capacitor needs to be replaced by an authorized repair center. “my aerator turns itself off and back on without the timer and without tripping the gfi breaker.” (single phase units only) each kasco single phase aerator has a thermal overl...
26 customer repair form 800 deere rd prescott, wi 54021 phone: 715‐262‐4488 fax: 715‐262‐4487 www.Kascomarine.Com sales@kascomarine.Com repair contact form kasco requires all repairs sent in must be accompanied by this form and marked to repairs attention. (ex. Attn: repairs) repairs returned should...
27.
28 registration information please register your aerator online at: www.Kascomarine.Com also fill in the information below and keep for your records. Model # (ex. 3.1jf)_______________________________ serial # (ex. 8001j311725)______________________________ purchase date:_____________________ purcha...
